SFD AISC 360 05

User Manual: SFD-AISC-360-05

Open the PDF directly: View PDF .
Page Count: 197

Download
Open PDF In Browser	View PDF

Steel Frame Design Manual
AISC 360-05 / IBC 2006

Steel Frame
Design Manual
AISC 360-05 / IBC 2006
For SAP2000®

ISO SAP102816M8 Rev. 0
Proudly developed in the United States of America

October 2016

Copyright
Copyright  Computers and Structures, Inc., 1978-2016
All rights reserved.
The CSI Logo® and SAP2000® are registered trademarks of Computers and Structures,
Inc. Watch & LearnTM is a trademark of Computers and Structures, Inc.
The computer program SAP2000® and all associated documentation are proprietary and
copyrighted products. Worldwide rights of ownership rest with Computers and
Structures, Inc. Unlicensed use of these programs or reproduction of documentation in
any form, without prior written authorization from Computers and Structures, Inc., is
explicitly prohibited.
No part of this publication may be reproduced or distributed in any form or by any
means, or stored in a database or retrieval system, without the prior explicit written
permission of the publisher.
Further information and copies of this documentation may be obtained from:
Computers and Structures, Inc.
www.csiamerica.com
info@csiamerica.com (for general information)
support@csiamerica.com (for technical support questions)

DISCLAIMER
CONSIDERABLE TIME, EFFORT AND EXPENSE HAVE GONE INTO THE
DEVELOPMENT AND DOCUMENTATION OF THIS SOFTWARE. HOWEVER,
THE USER ACCEPTS AND UNDERSTANDS THAT NO WARRANTY IS
EXPRESSED OR IMPLIED BY THE DEVELOPERS OR THE DISTRIBUTORS ON
THE ACCURACY OR THE RELIABILITY OF THIS PRODUCT.
THIS PRODUCT IS A PRACTICAL AND POWERFUL TOOL FOR STRUCTURAL
DESIGN. HOWEVER, THE USER MUST EXPLICITLY UNDERSTAND THE BASIC
ASSUMPTIONS OF THE SOFTWARE MODELING, ANALYSIS, AND DESIGN
ALGORITHMS AND COMPENSATE FOR THE ASPECTS THAT ARE NOT
ADDRESSED.
THE INFORMATION PRODUCED BY THE SOFTWARE MUST BE CHECKED BY
A QUALIFIED AND EXPERIENCED ENGINEER. THE ENGINEER MUST
INDEPENDENTLY VERIFY THE RESULTS AND TAKE PROFESSIONAL
RESPONSIBILITY FOR THE INFORMATION THAT IS USED.

Contents

Introduction
1.1

Load Combinations and Notional Loads

1-2

1.2

Stress Check

1-2

1.3

Direct Analysis Method vs. Effective Length Method

1-4

1.3.1
1.3.2

1-4
1-5

Effective Length Method
Direct Analysis Method

1.4

User Options

1-5

1.5

Non-Automated Items in the AISC 360-05/IBC 2006
Steel Frame Design

1-6

Design Algorithms
2.1

Check and Design Capability

2-1

2.2

Design and Check Stations

2-2

2.3

Demand/Capacity Ratios

2-3

Steel Frame Design AISC 360-05/IBC 2006

2.4

Design Load Combinations

2-4

2.5

Second Order P-Delta Effects

2-5

2.6

Analysis Methods

2-6

2.7

Notional Load Patterns

2-11

2.8

Member Unsupported Lengths

2-11

2.9

Effects of Breaking a Member into Multiple Elements

2-13

2.10 Effective Length Factor (K)

2-15

2.11 Supported Framing Types

2-18

2.12 Continuity Plates

2-19

2.13 Doubler Plates

2-21

2.14 Choice of Units

2-22

Steel Frame Design Using ANSI/AISC 360-05
3.1

Notations

3-2

3.2

Design Loading Combinations

3-6

3.3

Classification of Sections for Local Buckling

3-9

3.4

Calculation of Factored Forces and Moments

3-18

3.5

Calculation of Nominal Strengths

3-22

3.5.1
3.5.2
3.5.3

3-22
3-23
3-34

Nominal Tensile Strength
Nominal Compressive Strength
Nominal Flexure Strength

Contents

3.5.4
3.5.5
3.6

Design of Members for Combined Forces
3.6.1
3.6.2
3.6.3
3.6.4

Nominal Shear Strength
Nominal Torsional Strength

Doubly and Singly Symmetric Members
Subjected to Flexure and Axial Compression
Doubly and Singly Symmetric Members
Subjected to Flexure and Axial Tension
Unsymmetric Members Subjected to Flexure
and Axial Force
Members Subject to Torsion, Flexure, Shear
and Axial Force

3-65
3-71
3-73
3-74
3-77
3-79
3-81

Special Seismic Provisions (ANSI/AISC 341-05)
4.1

Notations

4-2

4.2

Design Preferences

4-2

4.3

Overwrites

4-3

4.4

Supported Framing Types

4-3

4.5

Applicability of the Seismic Requirements

4-4

4.6

Design Load Combinations

4-5

4.7

Classification of Sections for Local Buckling

4-7

4.8

Special Check for Column Strength

4-11

4.9

Member Design

4-12

4.9.1
4.9.2
4.9.3
4.9.4
4.9.5

4-12
4-13
4-13
4-14
4-14

Special Moment Frames (SMF)
Intermediate Moment Frame (IMF)
Ordinary Moment Frames (OMF)
Special Tress Moment Frames (STMF)
Special Concentrically Braced Frames (SCBF)

iii

Steel Frame Design AISC 360-05/IBC 2006

4.9.6
4.9.7

Ordinary Concentrically Braced Frames (OCBF)
Ordinary Concentrically Braced Frames from
Isolated Structures (OCBFI)
4.9.8 Eccentrically Braced Frames (EBF)
4.9.9 Buckling Restrained Braced Frames (BRBF)
4.9.10 Special Plate Shear Walls

4-17
4-18
4-22
4-22

4.10 Joint Design

4-22

4.10.1
4.10.2
4.10.3
4.10.4
4.10.5

4-23
4-29
4-33
4-36
4-39

Design of Continuity Plates
Design of Doubler Plates
Weak Beam Strong Column Measure
Evaluation of Beam Connection Shears
Evaluation of Brace Connection Forces

Design Output
5.1

Graphical Display of Design Information

5-2

5.2

Tabular Display of Design Information

5-5

5.3

Detailed Display of Member Specific Information

5-8

5.4

Output of Design Information

5-13

5.5

Error Messages and Warnings

5-16

Appendix A P-Delta Effects
Appendix B Steel Frame Design Preferences
Appendix C Steel Frame Design Procedure Overwrites
Appendix D Interactive Steel Frame Design
Appendix E Analysis Sections vs. Design Sections
Appendix F Error and Warning Messages
Bibliography

4-16

Chapter 1
Introduction

The design/check of steel frames is seamlessly integrated within the program.
Initiation of the design process, along with control of various design parameters, is accomplished using the Design menu. Automated design at the object
level is available for any one of a number of user-selected design codes, as
long as the structures have first been modeled and analyzed by the program.
Model and analysis data, such as material properties and member forces, are
recovered directly from the model database, and are used in the design process
in accordance with the user defined or default design settings. As with all design applications, the user should carefully review all of the user options and
default settings to ensure that the design process is consistent with the user’s
expectations. The AISC 360-05/IBC 2006 steel frame design options include
the use of the Direct Analysis Method. The software is well suited to make use
of the Direct Analysis Method because it can capture the second-order P-Delta
and P-δ effects, provided the user specifies that a nonlinear P-Delta analysis be
performed.
It should be noted that two design processes are available in CSiBridge: superstructure design (on the Design/Rating tab) and design of the individual elements comprising the structure (the Advanced > Frame Design commands).
This manual addresses the second design process.
Chapter 2 addresses prerequisites related to modeling and analysis for a successful design in accordance with ”AISC 360-05/IBC 2006.” Chapter 3 pro-

1-1

Steel Frame Design AISC 360-05/IBC 2006

vides detailed descriptions of the specific requirements as implemented in
”AISC 360-05/IBC 2006.” Chapter 4 provides detailed descriptions of the specific requirements for seismic loading as required by the specification in ANSI/AISC 341-05 code. The appendices provide details on various topics
referenced in this manual. The user also should review the AISC Direct Analysis Method Practical Guide.

1.1

Load Combinations and Notional Loads
The design is based on a set of user-specified loading combinations. However,
the program provides default load combinations for each supported design
code. If the default load combinations are acceptable, no definition of additional load combinations is required. The Direct Analysis Method requires that a
notional load, N = 0.002Yi , where Yi is the gravity load acting at level i, be
applied to account for the destabilizing effects associated with the initial imperfections and other conditions that may induce sway not explicitly modeled in
the structure. The user must be aware that notional loads must be defined and
assigned by the user. Currently, the software creates design combinations that
include notional loads and gravity loads only. If the user needs notional loads
that include combinations containing lateral loads, the user must define such
combinations manually. The automation of combinations, including notional
loads, is currently limited to gravity loads only. Design load combinations of
notional loads acting together with lateral loads currently are NOT automated
by the software.

1.2

Stress Check
Steel frame design/check consists of calculating the ﬂexural, axial, and shear
forces or stresses at several locations along the length of a member, and then
comparing those calculated values with acceptable limits. That comparison
produces a demand/capacity ratio, which typically should not exceed a value of
one if code requirements are to be satisfied. The program follows the same
review procedures whether it is checking a user-specified shape or a shape
selected by the program from a predefined list. The program also checks the
requirements for the beam-column capacity ratio, checks the capacity of the

1-2

Load Combinations and Notional Loads

Chapter 1 Introduction

panel zone, and calculates the doubler plate and continuity plate thickness, if
needed. The program does not do the connection design. However, it calculates
the design basis forces for connection design.
Program output can be presented graphically on the model, in tables for both
input and output data, or in calculation sheets prepared for each member. For
each presentation method, the output is in a format that allows the engineer to
quickly study the stress conditions that exist in the structure, and in the event
the member is not adequate, aid the engineer in taking appropriate remedial
measures, including altering the design member without re-running the entire
analysis.
The program supports a wide range of steel frame design codes, including
many national building codes. This manual is dedicated to the use of the menu
option ”AISC 36005/IBC 2006.” This option covers the ”ANSI/AISC 360-05
Specification for Structural Steel Buildings” (AISC 2005a, b), and the ”ANSI/
AISC 341-05 Seismic Provisions for Structural Steel Buildings Including Supplement No. 1” (AISC 2005c) codes.
The implementation covers loading and load combinations from ”ASCE/SEI
705 Minimum Design Loads for Buildings and Other Structures” (ASCE
2005), and also special requirements from ”IBC 2006 International Building
Code” (IBC 2006). Both LRFD (Load and Resistance Factor Design) and ASD
(Allowable Strength Design) codes are included in this implementation under
the same ”AISC 360-05/IBC 2006” code name. The LRFD and ASD are available as two options in the program’s preferences feature. In both cases, the
strengths are calculated in the nominal levels. The phi (LRFD) and Omega
(ADS) factors are applied during calculation of demand/capacity ratios only.
The design codes supported under ”AISC 360-05/IBC 2006” are written in kipinch units. All the associated equations and requirements have been implemented in the program in kip-in units. The program has been enabled with unit
conversion capability. This allows the users to enjoy the flexibility of choosing
any set of consistent units during creating and editing models, exporting and
importing the model components, and reviewing the design results.

Stress Check

1-3

Steel Frame Design AISC 360-05/IBC 2006

1.3

Direct Analysis Method vs. Effective Length
Method
The Direct Analysis Method described in AISC 360-05/IBC 2006, Appendix 7,
is substantially different from previous design methods supported by AISC.
The user should be knowledgeable about the Stability Analysis and Design
(Chapter C) requirements and the requirements pertaining to consideration of
the geometric imperfections, stiffness reductions, and the P-Δ and P-δ effects.
Several methods for consideration of the second-order effects are available to
the users. Each of these are described in detail in a subsequent section (see
User Options in this chapter) and in the Steel Frame Design Preferences,
Appendix B of this manual. Alternatively, if the user desires to use a more
traditional design method, the Effective Length method can be specified using
the Design Preferences.

1.3.1 Effective Length Method
For structures exhibiting small second-order effects, the effective length
method may be suitable. The effective length approach relies on two main
assumptions, namely, that the structural response is elastic and that all columns
buckle simultaneously. The effective length method also relies on a calibrated
approach to account for the differences between the actual member response
and the 2nd-order elastic analysis results. The calibration is necessary because
the 2nd-order elastic analysis does not account for the effects of distributed
yielding and geometric imperfections. Since the interaction equations used in
the effective length approach rely on the calibration corresponding to a 2ndorder elastic analysis of an idealized structure, the results are not likely
representative of the actual behavior of the structure. However, the results are
generally conservative. In the AISC 360-05/IBC 2006 code, the effective
length method is allowed provided the member demands are determined using
a second-order analysis (either explicit or by amplified first-order analysis) and
notional loads are included in all gravity load combinations. K-factors must be
calculated to account for buckling (except for braced frames, or where
Δ2 /Δ1 < 1.0, K = 1.0)

1-4

Direct Analysis Method vs. Effective Length Method

Chapter 1 Introduction

1.3.2 Direct Analysis Method
The Direct Analysis Method is expected to more accurately determine the
internal forces of the structure, provided care is used in the selection of the
appropriate methods used to determine the second-order effects, notional load
effects and appropriate stiffness reduction factors as defined in AISC 2.2, App.
7.3(3). Additionally, the Direct Analysis Method does not use an effective
length factor other than k = 1.0. The rational behind the use of k = 1.0 is that
proper consideration of the second-order effects (P-∆ and P-δ), geometric
imperfections (using notional loads) and inelastic effects (applying stiffness
reductions) better accounts for the stability effects of a structure than the earlier
Effective Length methods.

1.4

User Options
In addition to offering ASD and LRFD design, the Design Options menu provides seven analysis methods for design, as follows:


General Second Order Elastic Analysis (AISC C2.2a)



Second Order Analysis by Amplified First Order Analysis (AISC C2.1b)



Limited First Order Elastic Analysis (AISC 2.2b, App. 7.3(1))



Direct Analysis Method with General Second Order Analysis and Variable
Factor Stiffness Reduction (AISC 2.2, App. 7.3(3))



Direct Analysis Method with General Second Order Analysis and Fixed
Factor Stiffness Reduction (AISC 2.2, App. 7.3(3))



Direct Analysis Method with Amplified First Order Analysis and Variable
Factor Stiffness Reduction (AISC 2.2, App. 7.3(3))



Direct Analysis Method with Amplified First Order Analysis and Fixed
Factor Stiffness Reduction (AISC 2.2, App. 7.3(3))

These options are explained in greater detail in Chapter 2. The first three options make use of the effective length approach to determine the effective
length factors, K. The four options available for the Direct Design Method dif-

User Options

1-5

Steel Frame Design AISC 360-05/IBC 2006

fer in the use of a variable or fixed stiffness reduction factor and the method
used to capture the second-order effects. All four Direct Analysis Methods options use an effective length factor, K = 1.0.

1.5

Non-Automated Items in the AISC 360-05/IBC
2006 Steel Frame Design
Currently, the software does not automate the following:

1-6



Notional loads combinations that include lateral wind and quake loads



The validity of the analysis method. The user must verify the suitability of
the specified analysis method used under the User Options described in the
preceding sections. The AISC code requires, for instance, that the Direct
Analysis Method be used when a ratio of the second order displacements to
the first order displacements exceeds 1.5. This check currently must be
performed by the user.



P-Δ analysis. Since many different codes are supported by the software and
not all require a P-Δ analysis, the user must specify that a P-Δ analysis be
performed during the analysis phase so that the proper member forces are
available for use in the design phase. See the AISC Direct Analysis Method
Practical Guide for additional information.

Non-Automated Items in the AISC 360-05/IBC 2006 Steel Frame Design

Chapter 2
Design Algorithms

This chapter provides an overview of the basic assumptions, design preconditions, and some of the design parameters that affect the design of steel frames.
For referring to pertinent sections of the corresponding code, a unique prefix is
assigned for each code.

2.1

•

Reference to the ANSI/AISC 360-05 code is identified with the prefix
"AISC."

•

Reference to the ANSI/AISC 341-05 code is identified with the prefix
"AISC SEISMIC" or sometimes "SEISMIC" only.

•

Reference to the ASCE/SEI 7-05 code is identified with the prefix
"ASCE."

•

Reference to the IBC 2006 code is identified with the prefix "IBC."

Check and Design Capability
The program has the ability to check adequacy of a section (shape) in accordance with the requirements of the selected design code. Also the program can
automatically choose (i.e., design) the optimal (i.e., least weight) sections from
a predefined list that satisfies the design requirements.

2-1

Steel Frame Design AISC 360-05/IBC 2006

To check adequacy of a section, the program checks the demand/capacity
("D/C") ratios at a predefined number of stations for each design load combination. It calculates the envelope of the D/C ratios. It also checks the other requirements on a pass or fail basis. If the capacity ratio remains less than or
equal to the D/C ratio limit, which is a number close to 1.0, and if the section
passes all the special requirements, the section is considered to be adequate,
else the section is considered to be failed. The D/C ratio limit is taken as 0.95
by default. However, this value can be overwritten in the Preferences (see
Chapter 3).
To choose (design) the optional section from a predefined list, the program first
orders the list of sections in increasing order of weight per unit length. Then it
starts checking each section from the ordered list, starting with the one with
least weight. The procedure of checking each section in this list is exactly the
same as described in the preceding paragraph. The program will evaluate each
section in the list until it finds the least weight section that passes the code
checks. If no section in the list is acceptable, the program will use the heaviest
section but flag it as being overstressed.
To check adequacy of an individual section, the user must assign the section
using the Assign menu. In that case, both the analysis and design sections will
be changed.
To choose the optimal section, the user must first define a list of steel sections,
the Auto Select sections list. The user must next assign this list, in the same
manner as any other section assignment, to the frame members to be optimized. The program will use the median section by weight when doing the initial analysis. Check the program Help for more information about defining and
assigning Auto Select Section lists.

2.2

Design and Check Stations
For each design combination, steel frame members (beams, columns, and
braces) are designed (optimized) or checked at a number of locations (stations)
along the length of the object. The stations are located at equally spaced
segments along the clear length of the object. By default, at least three stations
will be located in a column or brace member, and the stations in a beam will be
spaced at most 2 feet apart (0.5 m if the model has been created in metric

2-2

Design and Check Stations

Chapter 2 Design Algorithms

units). The user can overwrite the number of stations in an object before the
analysis is run and refine the design along the length of a member by requesting more stations. Refer to the program Help for more information about
specifying the number of stations in an object.

2.3

Demand/Capacity Ratios
Determination of the controlling demand/capacity (D/C) ratios for each steel
frame member indicates the acceptability of the member for the given loading
conditions. The steps for calculating the D/C ratios are as follows:


The factored forces are calculated for axial, flexural, and shear at each defined station for each design combination. The bending moments are calculated about the principal axes. For I-Shape, Box, Channel, T-Shape, Double-Angle, Pipe, Circular, and Rectangular sections, the principal axes coincide with the geometric axes. For Single-Angle sections, the design considers the principal properties. For General sections, it is assumed that all
section properties are given in terms of the principal directions.
For Single-Angle sections, the shear forces are calculated for directions
along the geometric axes. For all other sections, the program calculates the
shear forces along the geometric and principal axes.



The nominal strengths are calculated for compression, tension, bending
and shear based on the equations provided later in this manual. For flexure,
the nominal strengths are calculated based on the principal axes of bending. For the I-Shape, Box, Channel, Circular, Pipe, T-Shape, Double-Angle
and Rectangular sections, the principal axes coincide with their geometric
axes. For the Angle sections, the principal axes are determined and all
computations related to flexural stresses are based on that.
The nominal strength for shear is calculated along the geometric axes for
all sections. For I-Shape, Box, Channel, T-Shape, Double-Angle, Pipe,
Circular, and Rectangular sections, the principal axes coincide with their
geometric axes. For Single-Angle sections, principal axes do not coincide
with the geometric axes.

Demand/Capacity Ratios

2-3

Steel Frame Design AISC 360-05/IBC 2006



2.4

Factored forces are compared to nominal strengths to determine D/C ratios.
In either case, design codes typically require that the ratios not exceed a
value of one. A capacity ratio greater than one indicates a member that has
exceeded a limit state.

Design Load Combinations
The design load combinations are the various combinations of the prescribed
load cases for which the structure needs to be checked. The program creates a
number of default design load combinations for steel frame design. Users can
add their own design combinations as well as modify or delete the program
default design load combinations. An unlimited number of design load combinations can be specified.
To define a design load combination, simply specify one or more load cases,
each with its own scale factor. The scale factors are applied to the forces and
moments from the load cases to form the factored design forces and moments
for each design load combination.
For normal loading conditions involving static dead load (DL), live load (LL),
roof live load (RL), snow load (SL), wind load (WL), earthquake load (EL),
notional load (NL), and dynamic response spectrum load (EL), the program has
built-in default design combinations for the design code. These are based on
the code recommendations.
The default design combinations assume all load cases declared as dead or live
to be additive. However, each load case declared as wind, earthquake, or
response spectrum cases, is assumed to be non-additive with other loads and
produces multiple lateral combinations. Also static wind, earthquake and
notional load responses produce separate design combinations with the sense
(positive or negative) reversed. The notional load patterns are added to load
combinations involving gravity loads only.
For other loading conditions involving moving load, time history, pattern live
load, separate consideration of roof live load, snow load, and the like, the user
must define the design load combinations in lieu of or in addition to the default
design load combinations. If notional loads are to be combined with other load
combinations involving wind or earthquake loads, the design load combina-

2-4

Design Load Combinations

Chapter 2 Design Algorithms

tions need to be defined in lieu of or in addition to the default design load combinations.
For multi-valued design combinations, such as those involving response spectrum, time history, moving loads and envelopes, where any correspondence
between forces is lost, the program automatically produces sub-combinations
using the maxima/minima values of the interacting forces. Separate combinations with negative factors for response spectrum load cases are not required
because the program automatically takes the minima to be the negative of the
maxima response when preparing the sub-combinations described previously.
The program allows live load reduction factors to be applied to the member
forces of the reducible live load case on a member-by-member basis to reduce
the contribution of the live load to the factored responses.

2.5

Second Order P-Delta Effects
The AISC 360-05/IBC 2006 steel frame design options include the use of the
Direct Analysis Method. The software is well suited to make us of the Direct
Analysis Method because each program can capture the second-order P-∆ and
P-δ effects, provided the user specifies that a nonlinear P-Delta analysis be performed.

Second Order P-Delta Effects

2-5

Steel Frame Design AISC 360-05/IBC 2006

∆
Original position of frame
element shown by vertical
line

δ
Final deflected position of the
frame element that includes the
global lateral translation, ∆, and
the local deformation of the
element, δ

Position of frame element
as a result of global lateral
translation, ∆, shown by
dashed line

P
Figure 2-1 System sway and element order effects

For a detailed discussion of the program capabilities and limitations, see
Appendix A.

2.6

Analysis Methods
The code requires that stability shall be provided for the structure as a whole
and for each of the elements. Any method of analysis that considers the influence of second order effects of P-∆ and P-δ , geometric imperfections, out-ofplumbness, and member stiffness reduction due to residual stresses are permitted by the code. The effects of geometric imperfection and out-of-plumbness
generally are captured by the use of notional loads. The effect of axial, shear
and flexural deformations and the effects of residual stresses on the member
stiffness reduction has been considered in a specialized method called "Direct
Analysis Method." This method can come in different incarnations (formats)
according to the choice of the engineer as allowed in the code.
The program offers the user seven analysis options for design:
Direct Analysis Method

2-6

Analysis Methods

Chapter 2 Design Algorithms

•

General Second Order Elastic Analysis with

τb variable

(user option 1, Default)

τb fixed
•

(user option 2)

Amplified First Order Elastic Analysis with

τb variable

(user option 3)

τb fixed

(user option 4)

Equivalent Length Method
•

General Second Order Elastic Analysis (AISC C2.1a)

(user option 5)

•

Amplified First Order Elastic Analysis (AISC C2.1b)

(user option 6)

Limited First-Order Analysis (AISC 2.2b, App. 7.3(1))

(user option 7)

A summary of all of the user options and requirements is provided in
Table 2-1. The main difference between the various options concerns the use of
the Direct Analysis Method or the Equivalent Length Method. Within each of
the categories, the user can choose the method to calculate the second-order
effects, namely, by a General Second Order Analysis or an Amplified FirstOrder Analysis. When the amplified first-order analysis is used, the force
amplification factors, B1 and B2 (AISC C2.1b), are needed. The B1 factor is
calculated by the program; however, the B2 factor is not. The user will need to
provide this value using the overwrite options that are described in Appendix
B.
When the user selects one of the options available under the Direct Analysis
Method, the user must further choose how the stiffness reduction factors for
EI and AE are to be considered. For options 1 and 3, Table 2-1, the stiffness
reduction factors ( τ b ) are variable because they are functions of the axial force
in the members, while for methods 2 and 4, the stiffness reduction factors are
fixed (0.8), and not a function of axial force. If the user desires, the stiffness
reduction factors ( τ b ) can be overwritten. When options 2 and 4 are used, a
higher notional load coefficient (0.003) must be used compared to methods 1
and 3 for which the notional load coefficient is 0.002. Also, all the direct analysis methods (methods 1 through 4) allow use of K -factors for sway condition
Analysis Methods

2-7

Steel Frame Design AISC 360-05/IBC 2006

( K 2 ) to be equal to 1, which is a drastic simplification over the other effective
length method.
The AISC requirements to include notional loads are also summarized in Table
2-1. The notional load coefficients (AISC C2.2a, App. 7.3) are summarized as
well. The program automates creation of notional load combinations for all
gravity loads but does not automate the creation of notional load combinations
that include lateral wind or seismic loads. Combinations for notional loads with
lateral loads are required for the Direct Analysis Method when the ∆2nd ∆1st
exceeds 1.5. Additionally, combinations for notional loads with lateral loads
are required if the Limited First Order Analysis, option 7, is used.
The Limited First Order Analysis, option 7, does not include the secondary
P-∆ and P-δ effects. This method has very limited applicability and might be
appropriate only when the axial forces in the columns are very small compared
to their Euler buckling capacities.
When using the LRFD provision, the actual load combinations are used for
second order P-∆ effects. When using the ASD provision, the load combinations are first amplified by 1.6 before the P-∆ analysis and then the results are
reduced by a factor of (1 1.6 ) (AISC 2.2a, App. 7.3).
Table 2-1 The Essentials and Limitations of the Design Analysis Methods
Direct Analysis Method
Option

Variable

Limitation or
Applicability

Essentials of the Method
2nd Order Analysis
Reduced stiffness
EI* = 0.8τ b EI
EA* = 0.8EA

General Second
Order Analysis

Variable
Factor Stiffness
Reduction

No limitation


1.0 for

τb = 
4  α Pr
  P
  y

α Pr
Py

≤ 0.5

  α Pr
1 −

Py



α Pr
 for
≥ 0.5

Py


B1 and B2 not used

K 2 = 1 (used for Pn )

Notional load with all combos, except for ∆2nd ∆1st ≤ 1.5 for
which notional load with gravity combos only
Notional load coefficient = 0.002 (typically)

2-8

Analysis Methods

Chapter 2 Design Algorithms

Table 2-1 The Essentials and Limitations of the Design Analysis Methods
Direct Analysis Method
Option

Variable

Limitation or
Applicability

Essentials of the Method
2nd Order Analysis
Reduced stiffness
EI* = 0.8τ b EI
EA* = 0.8EA

τ b = 1.0

Fixed Factor
Stiffness
Reduction

No limitation

B1 and B2 not used

K 2 = 1 (used for Pn )

Notional load with all combos, except for ∆2nd ∆1st ≤ 1.5
for which notional load with gravity combos only
Notional load coefficient = 0.003 (typically)
1st Order Analysis
Reduced Stiffness
EI* = 0.8τ b EI
EA* = 0.8EA

Amplified First
Order Analysis

Variable
Factor Stiffness
Reduction

No limitation


1.0 for

τb = 
4  α Pr
  P
  y

α Pr
Py

≤ 0.5

  α Pr
1 −

Py



α Pr
 for
≥ 0.5

Py


K1 = 1 for B1
K 2 = 1 for Pn and B2

Notional load with all combos, except for ∆2nd ∆1st ≤ 1.5
for which notional load with gravity combos only
Notional load coefficient = 0.002 (typically)
2nd Order Analysis
Reduced stiffness
EI* = 0.8τ b EI
Amplified First
Order Analysis

EA* = 0.8EA

Fixed Factor
Stiffness
Reduction

τ b = 1.0

No limitation

K 2 = 1 (used for Pn )

Notional load with all combos, except for ∆2nd ∆1st ≤ 1.5
for which notional load with gravity combos only
Notional load coefficient = 0.003 (typically)

Effective Length Method

Analysis Methods

2-9

Steel Frame Design AISC 360-05/IBC 2006

Table 2-1 The Essentials and Limitations of the Design Analysis Methods
Direct Analysis Method
Limitation or
Applicability
Limitation or
Applicability
∆2nd
≤ 1.5
∆1st

Option

Variable

Option

General Second
Order Elastic
Analysis

(for all stories)

α Pr
Py

= any

Essentials of the Method
2nd Order Analysis
Unreduced Stiffness
K = K 2 (used for Pn )
Notional load with gravity combos only
Notional load coefficient = 0.002 (typically)
B1 = 1

(for all columns)

B2 = 1

∆2nd
≤ 1.5
∆1st

1st Order Analysis
Unreduced stiffness
K1 for B1

(for all stories)

Amplified First
Order Analysis

Essentials of the Method

α Pr
Py

= any

(for all columns)

K 2 for B2
K = K 2 (used for Pn )

Notional load with gravity combos only
Notional load with coefficient = 0.002 (typically)
Use of B1 and B2

Limited First Order Analysis
∆2nd
≤ 1.5
∆1st
Limited First
Order Elastic
Analysis

(for all stories)

α Pr
Py

1st Order Analysis
Unreduced stiffness
K 2 for Pn (not B2 )
Notional load with all combos

≤ 0.5

∆
Notional load with coefficient = ( 2 )   ≥ 0.0042
L

(for all columns)

The program has several limitations that have been stated in Section 1-5 and
the preceding paragraphs. Additionally, the user must be aware that it is possible to choose a design option that violates certain provisions of the AISC code
that will not be identified by the program. The limitation for the use of the
∆
α Pr
must
effective length method, namely, the requirement that 2 nd ≤ 1.5 and
∆1st
Pe
be verified by the user. To assist users to in making validity checks, the ratio
α Pr
and τ are now reported in tabular form for each member.
Pe

2 - 10

Analysis Methods

Chapter 2 Design Algorithms

2.7

Notional Load Patterns
Notional loads are lateral loads that are applied at each framing level and are
specified as a percentage of the gravity loads applied at that level. They are
intended to account for the destabilizing effects of out-of-plumbness, geometric
imperfections, inelasticity in structural members, and any other effects that
could induce sway and that are not explicitly considered in the analysis.
The program allows the user to create a Notional Load pattern as a percentage
of the previously defined gravity load pattern to be applied in one of the global
lateral directions: X or Y. The user can define more than one notional load
pattern associated with one gravity load by considering different factors and
different directions. In the ANSI/AISC 360-05 code, the notional loads are
typically suggested to be 0.2% (or 0.002) (AISC C2.2a, App. 7.3(2)), a factor
referred to as the notional load coefficient in this document. The notional load
coefficient can be 0.003 (AISC App 7.3(3)). In some cases, it can be a function
of second order effects measured by relative story sway (AISC C2.26). The
code also gives some flexibility to allow the engineer-of-record to apply
judgment (AISC App. 7.3(2)).
The notional load patterns should be considered in combination with appropriate factors, appropriate directions, and appropriate senses. Some of the design
analysis methods need the notional loads to be considered only in gravity load
combinations (AISC App. 7.3(2)), and some of the methods need the notional
loads to be considered in all the design load combinations (AISC App 7.3(2)).
For a complete list, see Table 2-1 in the preceding "Second Order Effects and
Analysis Methods" section of this chapter.
Currently, the notional loads are not automatically included in the default
design load combinations that include lateral loads. However, the user is free to
modify the default design load combinations to include the notional loads with
appropriate factors and in appropriate load combinations.

2.8

Member Unsupported Lengths
The column unsupported lengths are required to account for column
slenderness effects for flexural buckling and for lateral-torsional buckling. The

Notional Load Patterns 2 - 11

Steel Frame Design AISC 360-05/IBC 2006

program automatically determines the unsupported length ratios, which are
specified as a fraction of the frame object length. These ratios times the frame
object lengths give the unbraced lengths for the member. These ratios can also
be overwritten by the user on a member-by-member basis, if desired, using the
overwrite option.
Two unsupported lengths, l33 and l22 , as shown in Figure 2-2 are to be
considered for flexural buckling. These are the lengths between support points
of the member in the corresponding directions. The length l33 corresponds to
instability about the 3-3 axis (major axis), and l22 corresponds to instability
about the 2-2 axis (minor axis). The length lLTB , not shown in the figure, is
also used for lateral-torsional buckling caused by major direction bending (i.e.,
about the 3-3 axis).
In determining the values for l22 and l33 of the members, the program recognizes various aspects of the structure that have an effect on these lengths, such
as member connectivity, diaphragm constraints and support points. The program automatically locates the member support points and evaluates the corresponding unsupported length.
It is possible for the unsupported length of a frame object to be evaluated by
the program as greater than the corresponding member length. For example,
assume a column has a beam framing into it in one direction, but not the other,
at a floor level. In this case, the column is assumed to be supported in one
direction only at that story level, and its unsupported length in the other direction will exceed the story height.
By default, the unsupported length for lateral-torsional buckling, lLTB , is taken
to be equal to the l22 factor. Similar to l22 and l33 , lLTB can be overwritten.

2 - 12

Member Unsupported Lengths

Chapter 2 Design Algorithms

Figure 2-2 Unsupported lengths l33 and l22

2.9

Effects of Breaking a Member into Multiple
Elements
The preferred method is to model a beam, column or brace member as one single element. However, the user can request that the program break a member
internally at framing intersections and at specified intervals. In this way, accuracy in modeling can be maintained, at the same time design/check specifications can be applied accurately. There is special emphasis on the end forces
(moments in particular) for many different aspects of beam, column and brace
design. If the member is manually meshed (broken) into segments, maintaining
the integrity of the design algorithm becomes difficult.
Manually, breaking a column member into several elements can affect many
things during design in the program.
1. The unbraced length: The unbraced length is really the unsupported length
between braces. If there is no intermediate brace in the member, the unbraced length is typically calculated automatically by the program from the
top of the flange of the beam framing the column at bottom to the bottom
of the flange of the beam framing the column at the top. The automatically
Effects of Breaking a Member into Multiple Elements 2 - 13

Steel Frame Design AISC 360-05/IBC 2006

calculated length factor typically becomes less than 1. If there are intermediate bracing points, the user should overwrite the unbraced length factor in
the program. The user should choose the critical (larger) one. Even if the
user breaks the element, the program typically picks up the unbraced length
correctly, provided that there is no intermediate bracing point.
2. K-factor: Even if the user breaks the member into pieces, the program typically can pick up the K -factors correctly. However, sometimes it can not.
The user should note the K -factors . All segments of the member should
have the same K -factor and it should be calculated based on the entire
member. If the calculated K -factor is not reasonable, the user can overwrite the K -factors for all the segments.
3. Cm factor: The Cm factor should be based on the end moments of
unbraced lengths of each segment and should not be based on the end
moments of the member. The program already calculates the Cm factors
based on the end moments of unbraced lengths of each segment. If the
break-up points are the brace points, no action is required by the user. If
the broken segments do not represent the brace-to-brace unsupported
length, the program calculated Cm factor is conservative. If this
conservative value is acceptable, no action is required by the user. If it is
not acceptable, the user can calculate the Cm factor manually for the
critical combination and overwrite its value for that segment.
4.

Cb factor: The logic is similar to that for the Cm factor.

B1 factor: This factor amplifies the factored moments for the P-δ effect. In
its expression, there are the Cm factor and the Euler Buckling capacity Pe .
If the user keeps the unbraced length ratios ( l33 and l22 ) and the
K -factors ( K 33 and K 22 ) correct, the B1 factor would be correct. If the

axial force is small, the B1 factor can be 1 and have no effect with respect
to modeling the single segment or multi-segment element.
6.

2 - 14

B2 factor: The program does not calculate the B2 factor. The program
assumes that the user turns on the P-∆. In such cases, B2 can be taken as
equal to 1. That means the modeling with one or multiple segments has no
effect on this factor.

Effects of Breaking a Member into Multiple Elements

Chapter 2 Design Algorithms

If the user models a column with a single element and makes sure that the L factors and K -factors are correct, the effect of B1 and B2 will be picked up
correctly. The factors Cm and Cb will be picked up correctly if there is no intermediate bracing point. The calculated Cm and Cb factors will be slightly
conservative if there are intermediate bracing points.
If the user models a column with multiple elements and makes sure that L factors and K -factors are correct, the effect of B1 and B2 will be picked up
correctly. The factors Cm and Cb will be picked up correctly if the member is
broken at the bracing points. The calculated Cm and Cb factors will be conservative if the member is not broken at the bracing points.

2.10 Effective Length Factor (K)
The effective length method for calculating member axial compressive strength
has been used in various forms in several stability based design codes. The
method originates from calculating effective buckling lengths, KL, and is based
on elastic/inelastic stability theory. The effective buckling length is used to
calculate an axial compressive strength, Pn, through an empirical column curve
that accounts for geometric imperfections, distributed yielding, and residual
stresses present in the cross-section.
There are two types of K -factors in the ANSI/AISC 360-05 code. The first
type of K -factor is used for calculating the Euler axial capacity assuming that
all of the beam-column joints are held in place, i.e., no lateral translation is allowed. The resulting axial capacity is used in calculation of the B1 factor. This
K -factor is named as K1 in the code. This K1 factor is always less than 1 and
is not calculated. By default the program uses the value of 1 for K1 . The program allows the user to overwrite K1 on a member-by-member basis.
The other K -factor is used for calculating the Euler axial capacity assuming
that all the beam-column joints are free to sway, i.e., lateral translation is allowed. The resulting axial capacity is used in calculating Pn . This K -factor is
named as K 2 in the code. This K 2 is always greater than 1 if the frame is a
sway frame. The program calculates the K 2 factor automatically based on
sway condition. The program also allows the user to overwrite K 2 factors on a

Effective Length Factor (K) 2 - 15

Steel Frame Design AISC 360-05/IBC 2006

member-by-member basis. The same K 2 factor is supposed to be used in calculation of the B2 factor. However the program does not calculate B2 factors
and relies on the overwritten values. If the frame is not really a sway frame, the
user should overwrite the K 2 factors.
Both K1 and K 2 have two values: one for major direction and the other for
minor direction, K1minor , K1major , K 2minor , K 2major .
There is another K -factor . K ltb for lateral torsional buckling. By default, K ltb
is taken as equal to K 2minor . However the user can overwrite this on a memberby-member basis.
The rest of this section is dedicated to the determination of K 2 factors.
The K -factor algorithm has been developed for building-type structures,
where the columns are vertical and the beams are horizontal, and the behavior
is basically that of a moment-resisting frame for which the K -factor calculation is relatively complex. For the purpose of calculating K -factors , the objects are identified as columns, beam and braces. All frame objects parallel to
the Z -axis are classified as columns. All objects parallel to the X - Y plane are
classified as beams. The remainders are considered to be braces.
The beams and braces are assigned K -factors of unity. In the calculation of the
K -factors for a column object, the program first makes the following four
stiffness summations for each joint in the structural model:
EI
Scx = ∑  c c 
 Lc  x

EI
Sbx = ∑  b b 
 Lb  x

EI
Scy = ∑  c c 
 Lc  y

EI
Sb y = ∑  b b 
 Lb  y

where the x and y subscripts correspond to the global X and Y directions and
the c and b subscripts refer to column and beam. The local 2-2 and 3-3 terms
EI 22 L22 and EI 33 L33 are rotated to give components along the global X and

Y directions to form the ( EI L ) x and ( EI L ) y values. Then for each column,

the joint summations at END-I and the END-J of the member are transformed
back to the column local 1-2-3 coordinate system, and the G -values for END-I

2 - 16

Effective Length Factor (K)

Chapter 2 Design Algorithms

and the END-J of the member are calculated about the 2-2 and 3-3 directions as
follows:
G I 22 =

S I c 22
S I b 22

G J 22 =

S J c 22
S J b 22

G I 33 =

S I c 33
S I b 33

G J 33 =

S J c 33
S J b 33

If a rotational release exists at a particular end (and direction) of an object, the
corresponding value of G is set to 10.0. If all degrees of freedom for a particular joint are deleted, the G -values for all members connecting to that joint will
be set to 1.0 for the end of the member connecting to that joint. Finally, if G I
and G J are known for a particular direction, the column K -factors for the corresponding direction is calculated by solving the following relationship for α:

α 2 G I G J − 36
6(G + G )
I

α
tan α

from which K = π/α. This relationship is the mathematical formulation for the
evaluation of K -factors for moment-resisting frames assuming sidesway to be
uninhibited. For other structures, such as braced frame structures, the
K -factors for all members are usually unity and should be set so by the user.
The following are some important aspects associated with the column
K -factor algorithm:


An object that has a pin at the joint under consideration will not enter the
stiffness summations calculated above. An object that has a pin at the far
end from the joint under consideration will contribute only 50% of the calculated EI value. Also, beam members that have no column member at the
far end from the joint under consideration, such as cantilevers, will not enter the stiffness summation.



If there are no beams framing into a particular direction of a column member, the associated G-value will be infinity. If the G-value at any one end
of a column for a particular direction is infinity, the K -factor corresponding to that direction is set equal to unity.



If rotational releases exist at both ends of an object for a particular direction, the corresponding K -factor is set to unity.
Effective Length Factor (K) 2 - 17

Steel Frame Design AISC 360-05/IBC 2006



The automated K -factor calculation procedure can occasionally generate
artificially high K -factors , specifically under circumstances involving
skewed beams, fixed support conditions, and under other conditions where
the program may have difficulty recognizing that the members are laterally
supported and K -factors of unity are to be used.



All K -factors produced by the program can be overwritten by the user.
These values should be reviewed and any unacceptable values should be
replaced.



The beams and braces are assigned K -factors of unity.

When a steel frame design is performed in accordance with ANSI/AISC 36005 provision and the analysis method is chosen to be any of the four direct
analysis methods, the K ltb and K 2 factors ( K 2minor and K 2major ) are automatically taken as 1 (AISC App. 7.1). However, their overwritten values are considered in design even if any of the Direct Analysis Methods is chosen.

2.11 Supported Framing Types
The code (ANSI/AISC 341-05) recognizes the following types of framing
systems.
Framing Type

2 - 18

References

SMF (Special Moment Frame)

AISC SEISMIC 9

IMF (Intermediate Moment Frame)

AISC SEISMIC 10

OMF (Ordinary Moment Frame)

AISC SEISMIC 11

STMF (Special Truss Moment Frame)

AISC SEISMIC 12

SCBF (Special Concentrically Braced Frame)

AISC SEISMIC 13

OCBF (Ordinary Concentrically Braced Frame)

AISC SEISMIC 14

EBF (Eccentrically Braced Frame)

AISC SEISMIC 15

BRBF (Buckling Restrained Braced Frame)

AISC SEISMIC 16

SPSW (Special Plate Shear Wall)

AISC SEISMIC 17

Supported Framing Types

Chapter 2 Design Algorithms

With regard to these framing types, the program has implemented specifications for all types of framing systems, except STMF, BRBF, and SPSW. Implementing those three types of framing require further information about
modeling.
The program recognizes the OCBF framing in its two separate incarnations:
OCBF for regular Ordinary Concentrically Braced Frames (AISC SEISMIC
14) and OCBFI for (base) Isolated Ordinary Concentrically Braced Frames
(AISC SEISMIC 14.5).
See Chapter 4 Special Seismic Provisions (ANSI/AISC 314-05) for additional
requirements.

2.12 Continuity Plates
In a plan view of a beam/column connection, a steel beam can frame into a
column in the following ways:


The steel beam frames in a direction parallel to the column major direction,
i.e., the beam frames into the column flange.



The steel beam frames in a direction parallel to the column minor direction, i.e., the beam frames into the column web.



The steel beam frames in a direction that is at an angle to both of the principal axes.

To achieve a beam/column moment connection, continuity plates, such as
shown in Figure 2-3, are usually placed on the column, in line with the top and
bottom flanges of the beam, to transfer the compression and tension flange
forces of the beam into the column.
For connection conditions described in the last two bullet items, the thickness
of such plates is usually set equal to the flange thickness of the corresponding
beam.

Continuity Plates 2 - 19

Steel Frame Design AISC 360-05/IBC 2006

Figure 2-3 Doubler Plates and Continuity Plates

2 - 20

Continuity Plates

Chapter 2 Design Algorithms

However, for the connection condition described by the first bullet item, where
the beam frames into the flange of the column, such continuity plates are not
always needed. The requirement depends upon the magnitude of the beam
flange force and the properties of the column.
The program investigates whether the continuity plates are needed based on the
requirements of the selected code. Columns of I-sections supporting beams of
I-sections only are investigated. The program evaluates the continuity plate requirements for each of the beams that frame into the column flange and reports
the maximum continuity plate area that is needed for each beam flange. The
continuity plate requirements are evaluated for moment frames only.

2.13 Doubler Plates
One aspect of the design of a steel framing system is an evaluation of the shear
forces that exist in the region of the beam column intersection known as the
panel zone. Shear stresses seldom control the design of a beam or column
member. However, in a moment resisting frame, the shear stress in the beamcolumn joint can be critical, especially in framing systems when the column is
subjected to major direction bending and the web of the column resists the joint
shear forces. In minor direction bending, the joint shear is carried by the column flanges, in which case the shear stresses are seldom critical, and the program does therefore not investigate this condition.
Shear stresses in the panel zone, due to major direction bending in the column,
may require additional plates to be welded onto the column web, depending
upon the loading and the geometry of the steel beams that frame into the column, either along the column major direction, or at an angle so that the beams
have components along the column major direction. See Figure 3-3. When
code appropriate, the program investigates such situations and reports the
thickness of any required doubler plates. Only columns with I-shapes and only
supporting beams with I-shapes are investigated for doubler plate requirements.
Also, doubler plate requirements are evaluated for moment frames only.

Doubler Plates 2 - 21

Steel Frame Design AISC 360-05/IBC 2006

2.14 Choice of Units
English as well as SI and MKS metric units can be used for input. The codes
are based on a specific system of units. All equations and descriptions presented in the subsequent chapters correspond to that specific system of units unless
otherwise noted. However, any system of units can be used to define and design a structure in the program.
It should be noted that two design processes are available in CSiBridge: superstructure design (on the Design/Rating tab) and design of the individual elements comprising the structure (the Advanced > Frame Design commands).
This manual addresses the second design process.

2 - 22

Choice of Units

Chapter 3
Design Using ANSI/AISC 360-05

This chapter provides a detailed description of the algorithms used by the programs in the design/check of structures in accordance with "ANSI/AISC 36005 — Specifications for Structural Steel Building" (AISC 2005a, b). The menu
option "AISC 360-05/IBC 2006" also covers the "ANSI/AISC 341-05 —
Seismic Provisions for Structural Steel Building Including Supplement No. 1"
(AISC 2005c), which is described in the next chapter. The implementation covers load combinations from "ASCE/SEI 7-05," which is described in the section "Design Loading Combinations" in this chapter. The loading based on
"ASCE/SEI 7-05" has been described in a separate document entitled "CSI
Lateral Load Manual" (CSI 2007). References also are made to IBC 2006 in
this document.
For referring to pertinent sections of the corresponding code, a unique prefix is
assigned for each code.
•

Reference to the ANSI/AISC 360-05 code is identified with the prefix
"AISC."

•

Reference to the ANSI/AISC 341-05 code is identified with the prefix
"AISC SEISMIC" or sometimes "SEISMIC" only.

•

Reference to the ASCE/SEI 7-05 code is identified with the prefix
"ASCE."

•

Reference to the IBC 2006 code is identified with the prefix "IBC."
3-1

Steel Frame Design AISC 360-05

3.1

Notations
The various notations used in this chapter are described herein.

3-2

Cross-sectional area, in2

Effective cross-sectional area for slender sections, in2

Gross cross-sectional area, in2

Av2,Av3

Major and minor shear areas, in2

Shear area, equal dtw per web, in2

Moment magnification factor for moments not causing sidesway

Moment magnification factor for moments causing sidesway

Bending coefficient

Moment coefficient

Warping constant, in6

Outside diameter of pipes, in

Modulus of elasticity, ksi

Fcr

Critical compressive stress, ksi

Compressive residual stress in flange assumed 10.0 for rolled
sections and 16.5 for welded sections, ksi

Yield stress of material, ksi

Shear modulus, ksi

I22

Minor moment of inertia, in4

I33

Major moment of inertia, in4

Torsional constant for the section, in4

Notations

Chapter 3 - Design using ANSI/AISC 360-05

Effective length factor

Effective length factor for braced condition

Effective length factor for unbraced condition

K33,K22

Effective length K-factors in the major and minor directions for
appropriate braced (K1) and unbraced (K2) condition

Laterally unbraced length of member, in

Limiting laterally unbraced length for full plastic capacity, in

Limiting laterally unbraced length for inelastic lateral-torsional
buckling, in

Mcr

Elastic buckling moment, kip-in

Mlt

Factored moments causing sidesway, kip-in

Mnt

Factored moments not causing sidesway, kip-in

Mn33,Mn22

Nominal bending strength in major and minor directions, kip-in

Mob

Elastic lateral-torsional buckling moment for angle sections, kipin

Mr33, Mr22

Major and minor limiting buckling moments, kip-in

Factored moment in member, kip-in

Mu33, Mu22

Factored major and minor moments in member, kip-in

Euler buckling load, kips

Nominal axial load strength, kip

Factored axial force in member, kips

AgFy, kips

Reduction factor for slender section, = QaQs

Reduction factor for stiffened slender elements
Notations

3-3

Steel Frame Design AISC 360-05

3-4

Reduction factor for unstiffened slender elements

Section modulus, in3

S33,S22

Major and minor section moduli, in3

Seff,33,Seff,22

Effective major and minor section moduli for slender sections,
in3

Section modulus for compression in an angle section, in3

Vn2,Vn3

Nominal major and minor shear strengths, kips

Vu2,Vv3

Factored major and minor shear loads, kips

Plastic modulus, in3

Z33,Z22

Major and minor plastic moduli, in3

Nominal dimension of plate in a section, in
longer leg of angle sections, bf − 2tw for welded and bf − 3tw for
rolled box sections, and the like

Effective width of flange, in

Flange width, in

Overall depth of member, in

Effective depth of web, in

Clear distance between flanges less fillets, in
assumed d − 2k for rolled sections, and d − 2tf for welded sections

Distance from outer face of flange to web toe of fillet, in

Parameter used for section classification
kc = 4 h t w , 0.35 ≤ kc ≤ 0.763

l33,l22

Major and minor directions unbraced member lengths, in

Radius of gyration, in

Notations

Chapter 3 - Design using ANSI/AISC 360-05

r33,r22

Radii of gyration in the major and minor directions, in

Thickness, in

Flange thickness, in

Thickness of web, in

βw

Special section property for angles, in

Slenderness parameter

λc,λe

Column slenderness parameters

λp

Limiting slenderness parameter for compact element

λr

Limiting slenderness parameter for non-compact element

λs

Limiting slenderness parameter for seismic element

λslender

Limiting slenderness parameter for slender element

ϕb

Resistance factor for bending

ϕc

Resistance factor for compression

ϕt

Resistance factor for tension yielding

ϕT

Resistance factor for torsion

ϕv

Resistance factor for shear

Ωb

Safety factor for bending

Ωc

Safety factor for compression

Ωt

Safety factor for tension

ΩT

Safety factor for torsion

Ωv

Safety factor for shear

Notations

3-5

Steel Frame Design AISC 360-05

3.2

Design Loading Combinations
The structure is to be designed so that its design strength equals or exceeds the
effects of factored loads stipulated by the applicable design code. The default
design combinations are the various combinations of the already defined load
cases, such as dead load (DL), live load (LL), roof live load (RL), snow load
(SL), wind load (WL), and horizontal earthquake load (EL).
AISC 360-05 refers to the applicable building code for the loads and load combinations to be considered in the design, and to ASCE 7-05 in the absence of
such a building code. Hence, the default design combinations used in the current version are the ones stipulated in ASCE 7-05:
For design in accordance with LRFD provisions:
1.4 DL
1.2 DL + 1.6 LL + 0.5 RL
1.2 DL + 1.0 LL + 1.6 RL

(ASCE 2.3.2-1)
(ASCE 2.3.2-2)
(ASCE 2.3.2-3)

1.2 DL + 1.6 LL + 0.5 SL
1.2 DL + 1.0 LL + 1.6 SL

(ASCE 2.3.2-2)
(ASCE 2.3.2-3)

0.9 DL ± 1.6 WL
1.2 DL + 1.6 RL ± 0.8 WL
1.2 DL + 1.0 LL + 0.5RL ± 1.6 WL

(ASCE 2.3.2-6)
(ASCE 2.3.2-3)
(ASCE 2.3.2-4)

1.2 DL + 1.6 SL ± 0.8 WL
1.2 DL + 1.0 LL + 0.5SL ± 1.06 WL

(ASCE 2.3.2-3)
(ASCE 2.3.2-4)

0.9 DL ± 1.0 EL
1.2 DL + 1.0 LL + 0.2SL ± 1.0EL

(ASCE 2.3.2-7)
(ASCE 2.3.2-5)

For design in accordance with ASD provisions:

3-6

1.0 DL
1.0 DL + 1.0 LL

(ASCE 2.4.1-1)
(ASCE 2.4.1-2)

1.0 DL + 1.0 RL
1.0 DL + 0.75 LL + 0.75 RL
1.0 DL + 1.0 SL
1.0 DL + 0.75 LL + 0.75 SL

(ASCE 2.4.1-3)
(ASCE 2.3.2-4)
(ASCE 2.4.1-3)
(ASCE 2.3.2-4)

Design Loading Combinations

Chapter 3 - Design using ANSI/AISC 360-05

1.0 DL ± 1.0 WL
1.0 DL + 0.75 LL + 0.75 RL ± 0.75 (WL)
1.0 DL + 0.75 LL + 0.75 SL ± 0.75 (WL)
0.6 DL ± 1.0 WL

(ASCE 2.4.1-5)
(ASCE 2.4.1-6)
(ASCE 2.4.1-6)
(ASCE 2.4.1-7)

1.0 DL ± 0.7 EL
1.0 DL + 0.75 LL + 0.75 SL ± 0.75(0.7 EL)
0.6 DL ± 0.7 EL

(ASCE 2.4.1-5)
(ASCE 2.4.1-6)
(ASCE 2.4.1-8)

Most of the analysis methods recognized by the code are required to consider
Notional Load in the design loading combinations for steel frame design. The
program allows the user to define and create notional loads as individual load
cases from a specified percentage of a given gravity load acting in a particular
lateral direction. These notional load patterns should be considered in the combinations with appropriate factors, appropriate directions, and appropriate
senses. Currently, the program automatically includes the notional loads in the
default design load combinations for gravity combinations only. The user is
free to modify the default design load combinations to include the notional
loads. For further information, refer to the "Notional Load Patterns" section in
Chapter 2.
The program automatically considers seismic load effects, including overstrength factors (ASCE 12.4.3), as special load combinations that are created
automatically from each load combination, involving seismic loads. In that
case, the horizontal component of the force is represented by Ehm and the vertical component of the force is represented byEv , where
Ehm = Ω0QE

(ASCE 12.4.3.1)

Ev = 0.2SDSD

(ASCE 12.4.2.2)

where, Ωo is the overstrength factor and it is taken from ASCE 7-05 Table
12.2-1. The factor SDS is described later in this section. Effectively, the special
seismic combinations that are considered for the LRFD provision are
(0.9 − 0.2SDS)DL ± Ω0QE

(ASCE 12.4.3.2)

(1.2 − 0.2SDS)DL ± Ω0QE + 1.0LL

(ASCE 12.4.3.2)

and for the ASD provision the combinations are
(1.0 − 0.14SDS)DL ± 0.7Ω0QE

(ASCE 12.4.3.2)
Design Loading Combinations

3-7

Steel Frame Design AISC 360-05

(1.0 + 0.105SDS)DL ± 0.75(0.7Ω0)QE + 0.75LL

(ASCE 12.4.3.2)

(0.6 − 0.14SDS)DL ± 0.7Ω0QE

(ASCE 12.4.3.2)

The program assumes that the defined earthquake load is really the strength
level earthquake, which is equivalent to QE as defined in Section 12.4.2.1 of
the ASCE 7-05 code. For regular earthquake, load is considered to have two
components: horizontal, Eh and vertical Ev , which are taken as
Eh = ρθE

(ASCE 12.4.2.1)

Ev = 0.2SDSD

(ASCE 12.4.2.2)

where, ρ is the redundancy factor as defined in Section 12.3.4 of ASCE 7-05,
and the SDS is the design earthquake spectral response acceleration parameters
at short periods, as defined in Section 11.4.4 of ASCE 7-05 code.
Effectively, the seismic load combination for the LRFD provision becomes:
(1.2 + 0.2SDS)DL ± ρQE

(ASCE 2.3.2-5, 12.4.2.3)

(1.2 + 0.2SDS)DL ± ρQE + 1.0LL

(ASCE 2.3.2-5, 12.4.2.3)

(0.9 − 0.2SDS)DL ± ρQE

(ASCE 2.3.2-7, 12.4.2.3)

The seismic load combinations for the ASD provision become:
(1.0 + 0.14SDS)DL ± 0.7ρQE

(ASCE 2.4.1-5, 12.4.2.3)

(1.0 + 0.105SDS)DL ± 0.75(0.7ρ)QE + 0.75LL

(ASCE 2.4.1-6, 12.4.2.3)

(0.6 − 0.14SDS)DL ± 0.7ρQE

(ASCE 2.4.1-7, 12.4.2.3)

The program assumes that the seismic loads defined as the strength level load
is the program load case. Otherwise, the factors ρ, Ωo , and SDS will not be able
to scale the load to the desired level.
The combinations described herein are the default loading combinations only.
They can be deleted or edited as required by the design code or engineer-ofrecord.

3-8

Design Loading Combinations

Chapter 3 - Design using ANSI/AISC 360-05

The program allows live load reduction factors to be applied to the member
forces of the reducible live load case on a member-by-member basis to reduce
the contribution of the live load to the factored responses.

3.3

Classification of Sections for Local Buckling
The nominal strengths for axial, compression, and flexure are dependent on the
classification of the section as Seismically Compact, Compact, Noncompact,
Slender, or Too Slender. Compact or Seismically Compact sections are capable
of developing the full plastic strength before local buckling occurs. Noncompact sections can develop partial yielding in compression, and buckle
inelastically before reaching to a fully plastic stress distribution. Slender sections buckle elastically before any of the elements yield under compression.
Seismically Compact sections are capable of developing the full plastic
strength before local buckling occurs when the section goes through low cycle
fatigue and withstands reversal of load under seismic conditions.
Sections are classified as Compact, Noncompact, or Slender sections in
accordance with Section B4 of the code (AISC B4). For a section to qualify as
Compact, its flanges must be continuously connected to the web or webs and
the width-thickness ratios of its compression elements must not exceed the
limiting width-thickness ratios λp from Table B4.1 of the code. If the widththickness ratio of one or more compression elements exceeds λp, but does not
exceed λr from Table B4.1, the section is Noncompact. If the width-thickness
ratio of any element exceeds λr but does not exceed λs, the section is Slender.
If the width-thickness ratio of any element exceed λs, the section is considered
Too Slender. The expressions of λp, λr, and λs, as implemented in the program,
are reported in Table 3-1 (AISC Table B4.1, B4, F8, F13.2). In that table all
expressions of λp and λr are taken from AISC section B4 and AISC Table
B4.1. The limit demarcating Slender and Too Slender has been identified as λs
in this document. The expressions of λs for I-Shape, Double Channel, Channel
and T-Shape sections are taken from AISC section F13.2. The expression of λs
for Pipe Sections is taken from AISC section F8. The expression of λp for
Angle and Double Angle sections is taken from AISC Seismic code
ANSI/AISC 341-05 Table I-8-1.

Classification of Sections for Local Buckling

3-9

Steel Frame Design AISC 360-05

The table uses the variables kc, FL, h, hp, hc, bf, tf, tw, b, t, D, d, and so on. The
variables b, d, D and t are explained in the respective figures inside the table.
The variables bf, tf, h, hp, hc, and tw are explained in Figure 3-1. For Doubly
Symmetric I-Shapes, h, hp, and hc are all equal to each other.

3 - 10

Classification of Sections for Local Buckling

Chapter 3 - Design using ANSI/AISC 360-05

b ft

k
hp 2
h= h=
hp
c

h= h=
hp
c

hc 2
h

tf
b

b fc

b
=
b b f − 3tw

k
tw
h= h=
hp
c

PNA
NA

h= h=
hp
c

hc= d − 3t f

tf
tf
bf

bf
bf
b

bf
s

tf
d

h
b

tw
AISC-2005: Axes Conventions
2-2 is the cross section axis
parallel to the webs, the
longer dimension of tubes,
the longer leg of single
angles, or the side by side
legs of double anges. This is
the same as the y-y axis.

2, y

3, x

3-3 is orthogonal to 2-2. This is
the same as the x-x axis.

3, x

2, y

Figure 3-1 AISC 360-05 Definition of Geometric Properties

Classification of Sections for Local Buckling 3 - 11

Steel Frame Design AISC 360-05

For unstiffened elements supported along only one edge parallel to the direction of compression force, the width shall be taken as follows:
(a) For flanges of I-shaped members and tees, the width b is one-half the fullflange width, bf.
(b) For legs of angles and flanges of channels and zees, the width b is the full
nominal dimension.
(c) For plates, the width b is the distance from the free edge to the first row of
fasteners or line of welds.
(d) For stems of tees, d is taken as the full nominal depth of the section.
Refer to Table 3-1 (AISC Table B4.1) for the graphic representation of unstiffened element dimensions.
For stiffness elements supported along two edges parallel to the direction of the
compression force, the width shall be taken as follows:
(a) For webs of rolled or formed sections, h is the clear distance between
flanges less the fillet or corner radius at each flange; hc is twice the distance from the centroid to the inside face of the compression flange less the
fillet or corner radius.
(b) For webs of built-up sections, h is the distance between adjacent lines of
fasteners or the clear distance between flanges when welds are used, and hc
is twice the distance from the centorid to the nearest line of fasteners at the
compression flange or the inside face of the compression flange when
welds are used; hp is twice the distance from the plastic neutral axis to the
nearest line of fasteners at the compression flange or the inside face of the
compression flange when welds are used.
(c) For flange or diaphragm plates in built-up sections, the width b is the distance between adjacent lines of fasteners or lines of welds.

3 - 12

Classification of Sections for Local Buckling

Chapter 3 - Design using ANSI/AISC 360-05

Table 3-1 Limiting Width-Thickness Ratios of Compression Elements for Classification Sections

Doubly Symmetric I-Shape

Section
Type

Description
of Element

Example

WidthThickness
AISC Ratio,
Case
(λ)
No.

Limiting Width-Thickness Ratios for Compression
Element
Compact
NonCompact
Slender

(λ )

Flexural
compression
of flanges of
rolled
I-Shapes

b f 2t f

0.38 E Fy

1.0 E Fy

No Limit

Flexural
compression
in flanges of
built-up
I-Shapes

b f 2t f

0.38 E Fy

0.95 kc E FL

No Limit

Axial only
compression
in flanges of
rolled
I-Shapes

b f 2t f

0.38 E Fy

0.56 E Fy

No Limit

Axial only
compression
in flanges of
built-up
I-Shapes

b f 2t f

0.38 E Fy

0.64 kc E FL

No Limit

Flexure in web

h tw

3.76 E Fy

5.70 E Fy

Web in axial
only
compression

h tw

1.49 E Fy

(beams)
No limit for columns
and braces

Flexural
Compression
of flanges of
rolled
I-Shapes

b f 2t f

0.38 E Fy

1.0 E Fy

No Limit

{

}

Singly Symmetric
I-Shapes

min 0.42 E Fy ,260

(beams)
No limit for columns
and braces

{

}

min 0.42 E Fy ,260

Classification of Sections for Local Buckling 3 - 13

Steel Frame Design AISC 360-05

Table 3-1 Limiting Width-Thickness Ratios of Compression Elements for Classification Sections

Singly Symmetric I-Shapes (continued)

Section
Type

Description
of Element

Example

WidthThickness
AISC Ratio,
Case
(λ)
No.

Limiting Width-Thickness Ratios for Compression
Element
Compact
NonCompact
Slender

(λ )

Flexural
Compression
in flanges of
built-up
I-Shapes

b f 2t f

0.38 E Fy

0.95 kc E FL

No Limit

Axial only
compression
in flanges of
rolled
I-Shapes

b f 2t f

0.38 E Fy

0.56 E Fy

No Limit

Axial only
compression
in flanges of
built-up
I-Shapes

b f 2t f

0.38 E Fy

0.64 kc E FL

No Limit

5.70 E Fy

No Limit

Flexure in
Web

hc t w



Mp
− 0.09 
 0.54

My



≤ λr

{

}

min 0.42 E Fy ,260

Flexure in
Web

h tw

(beams)
No limit for columns
and braces

bf t f

0.38 E Fy

1.0 E Fy

No Limit

Axial only
compression
in flanges

bf t f

0.38 E Fy

0.56 E Fy

No Limit

Channel

Flexural
compression
in flanges

3 - 14

Classification of Sections for Local Buckling

Chapter 3 - Design using ANSI/AISC 360-05

Table 3-1 Limiting Width-Thickness Ratios of Compression Elements for Classification Sections

Section
Type

Description
of Element

Example

WidthThickness
AISC Ratio,
Case
(λ)
No.

Limiting Width-Thickness Ratios for Compression
Element
Compact
NonCompact
Slender

(λ )
p

(λ )

{

}

T-Shape

Box

Double Channel

Channel (continued)

min 0.42 E Fy ,260

Flexure in web

h tw

3.76 E Fy

5.70 E Fy

Web in axial
only
compression

h tw

1.49 E Fy

(beams)
No limit for columns
and braces

Flexural
compression
in flanges

bf t f

0.38 E Fy

1.0 E Fy

No Limit

Axial only
compression
in flanges

bf t f

0.38 E Fy

0.56 E Fy

No Limit

Flexure in web

h tw

3.76 E Fy

5.70 E Fy

Web in axial
only
compression

h tw

1.49 E Fy

(beams)
No limit for columns
and braces

Flexural or
axial
compression
of flanges
under major
axis bending

b t

1.12 E Fy

1.40 E Fy

No Limit

Flexure in web

h t

2.42 E Fy

5.70 E Fy

No Limit

Flexural or
axial
compression
in flanges

b f 2t f

0.38 E Fy

1.0 E Fy

No Limit

Compression
in stems

d tw

0.30 E Fy

0.75 E Fy

No Limit

(beams)
No limit for columns
and braces

{

}

min 0.42 E Fy ,260

{

}

min 0.42 E Fy ,260

(beams)
No limit for columns
and braces

{

}

min 0.42 E Fy ,260

Classification of Sections for Local Buckling 3 - 15

Steel Frame Design AISC 360-05

Table 3-1 Limiting Width-Thickness Ratios of Compression Elements for Classification Sections

Description
of Element

Example

Limiting Width-Thickness Ratios for Compression
Element
Compact
NonCompact
Slender

(λ )

Any type of
compression
in leg

b t

0.30 E Fy

0.45 E Fy

No Limit

Any type of
compression
in leg

b t

0.30 E Fy

0.45 E Fy

No Limit

Flexural
compression
in any leg

b t

0.54 E Fy

0.91 E Fy

No Limit

Axial only
compression
in any leg

b t

0.30 E Fy

0.45 E Fy

No Limit

Flexural
compression

D t

0.07 E Fy

0.31 E Fy

0.45 E Fy

Axial only
compression

D t

0.07 E Fy

0.11 E Fy

0.45 E Fy

Pipe

Angle

Double Angle

Section
Type

WidthThickness
AISC Ratio,
Case
(λ)
No.

Round
Bar
Rectangular
General
SD
Section

―――

――

―――

Assumed Noncompact

―――

――

―――

Assumed Noncompact

―――

――

―――

Assumed Noncompact

―――

――

―――

Assumed Noncompact

(d) For flanges of rectangular hollow structural sections (HSS), the width b is
the clear distance between webs less the inside corner radius on each side.
For webs of rectangular HSS, h is the clear distance between the flanges
less the inside corner radius on each side. If the corner radius is not known,
b and h shall be taken as the corresponding outside dimension minus three
times the thickness. The thickness, t, shall be taken as the design wall
thickness, in accordance with AISC Section B3.12.

3 - 16

Classification of Sections for Local Buckling

Chapter 3 - Design using ANSI/AISC 360-05

Refer to Table 3-5 (AISC Table B4.1) for the graphic representation of stiffened element dimensions.
The design wall thickness, t, for hollow structural sections, such as Box and
Pipe sections, is modified for the welding process (AISC B3.12). If the welding
process is ERW (Electric-Resistance Welding), the thickness is reduced by a
factor of 0.93. However, if the welding process is SAW (Submerged Arc
Welded), the thickness is not reduced. The Overwrites can be used to choose if
the thickness of HSS sections should be reduced for ERW on a member-bymember basis. The Overwrites can also be used to change the reduction factor.
The variable kc can be expressed as follows:
kc =

4
h tw

0.35 ≤ kc ≤ 0.76.

(AISC Table B4.1 Note a)
(AISC Table B4.1 Note a)

For Doubly Symmetric I-Shapes, Channels, and Double Channels, FL can be
expressed as follows:
FL = 0.7Fy,

(AISC Table B4.1 Note b)

and for Singly Symmetric I-Shape sections, FL can be expressed as follows:

S xt
Fy , where
S xc

(AISC Table B4.1 Note b, F4-6)

0.5Fy ≤ FL ≤ 0.7Fy.

(AISC Table B4.1 Note b, F4-6)

FL =

Seismically Compact sections are compact sections that satisfy a more stringent width-thickness ratio limit, λps. This limit λps is presented in Table 4-1 in
Chapter 4, which is dedicated to the seismic code.
In classifying web slenderness of I-Shapes, Box, Channel, Double Channel,
and all other sections, it is assumed that there are no intermediate stiffeners.
Double angles and channels are conservatively assumed to be separated.
Stress check of Too Slender sections is beyond the scope of this program.

Classification of Sections for Local Buckling 3 - 17

Steel Frame Design AISC 360-05

3.4

Calculation of Factored Forces and Moments
The factored member loads that are calculated for each load combination are
Pr, Mr33, Mr22, Vr2, Vr3 and Tr corresponding to factored values of the axial load,
the major and minor moments and shears, and torsion, respectively. These factored loads are calculated at each of the previously defined stations.
The factored forces can be amplified to consider second order effects, depending on the choice of analysis method chosen in the Preferences. If the analysis
method is chosen to be General Second Order Elastic Analysis or any of the
Direct Analysis methods with General Second Order Analysis, it is assumed
that the analysis considers the influence of second-order effects (P-∆ and P-δ
effects); hence the analysis results are used without amplification (AISC C2.1,
C2.2a, App 7.3). Second-order effects due to overall sway of the structure can
usually be accounted for, conservatively, by considering the second-order effects on the structure under one set of loads (usually the most severe gravity
load case), and performing all other analyses as linear using the stiffness matrix
developed for this one set of P-delta loads (see also White and Hajjar 1991).
For a more accurate analysis, it is always possible to define each loading combination as a nonlinear load case that considers only geometric nonlinearities.
For both approaches, when P-δ effects are expected to be important, use more
than one element per line object (accomplished using the automatic frame subdivide option; refer to the program Help for more information about automatic
frame subdivide).
If the analysis method is chosen to be Second Order Analysis by Amplified
First Order Analysis or any of the Direct Analysis Methods with Amplified
First Order Analysis (AISC C2.1b, C2.2, App 7.3), it is assumed that the analysis does not consider the influence of second order effects (P-∆ and P-δ).
Hence the analysis results are amplified using B1 and B2 factors using the following approximate second-order analysis for calculating the required flexural
and axial strengths in members of lateral load resisting systems. The required
second-order flexural strength, Mr , and axial strength, Pr are determined as follows:
Mr = B1Mnt + B2Mlt

(AISC C2-1a)

Pr = Pnt + B2Plt

(AISC C2-1b)

where,
3 - 18

Calculation of Factored Forces and Moments

Chapter 3 - Design using ANSI/AISC 360-05

=
B1

=
B2

Cm
1− α

Pr
Pe1

≥ 1, and

1
≥ 1,
αΣPnt
1−
ΣPe 2

(AISC C2-2)

(AISC C2-3)

where,
α

1.0 for LRFD,
= 
1.6 for ASD,

= required second-order flexural strength using LFRD and ASD
load combinations, kip-in (N-mm)

Mnt

= first-order moment using LFRD and ASD load combinations,
assuming there is no lateral translation of the frame, kip-in. (Nmm)

Mlt

= first-order moment using LRFD or ASD load combinations
caused by lateral translation of the frame only, kip-in (N-mm)

= required second-order axial strength using LRFD or ASD load
combinations, kip (N)

Pnt

= first-order axial force using LRFD or ASD load combinations,
assuming there is no lateral translation of the frame, kips (N)

ΣPnt

= total vertical load supported by the story using LRFD or ASD
load combinations, including gravity column loads, kips (N)

Plt

= first-order axial force using LRFD or ASD load combinations
caused by lateral translation of the frame only, kips (N)

= a coefficient assuming no lateral translation of the frame,
whose value is taken as follows:
(i) For beam-columns not subject to transverse loading between supports in the plane of bending,

Calculation of Factored Forces and Moments 3 - 19

Steel Frame Design AISC 360-05

C=
0.6 − 0.4 ( M a M b ) ,
m

(AISC C2-4)

where, Ma and Mb, calculated from a first-order analysis,
are the smaller and larger moments, respectively, at the
ends of that portion of the member unbraced in the plane
of bending under consideration. M a M b is positive when
the member is bent in reverse curvature, negative when
bent in single curvature.
(ii) For beam-columns subjected to transverse loading between
supports, the value of Cm is conservatively taken as 1.0 for
all cases.
When Mb is zero, Cm is taken as 1.0, the program defaults
Cm to 1.0, if the unbraced length is more than actual member length. The user can overwrite the value of Cm for any
member. Cm can be expressed as follows:

1.00,

1.00,

Cm = 1.00,

M
0.6 − 0.4 a ,
Mb

1.00,


if length is more than actual length,
if tension member,
if both ends unrestrained,
if no transverse loading, and
if transverse loading is present.

(AISC C2-1b)
Pel

= elastic critical buckling resistance of the member in the plane
of bending, calculated based on the assumption of zero sidesway, kips (N)
Pe1 =

π2 EI

( K1 L )

(AISC C2-5)

If any of the direct analysis methods are used, the reduced value of EI is used (AISC App. 7.3(1)).

3 - 20

Calculation of Factored Forces and Moments

Chapter 3 - Design using ANSI/AISC 360-05

ΣPe2

= elastic critical buckling resistance for the story determined by
sidesway buckling analysis, kips (N)
For moment frames, where sidesway buckling effective length
factors K2 are determined for the columns, it is the elastic story
sidesway buckling resistance and calculated as
ΣPe 2 =
Σ

π2 EI

( K2 L )

(AISC C2-6a)

where,
E

modulus of elasticity of steel = 29,000 ksi
(200,000 MPa)
If any of the direct analysis methods are used,
the reduced value of EI is used (AISC App.
7.3(1)).

moment of inertia in the plane of bending, in.4
(mm4)

story height, in. (mm)

K1 =

effective length factor in the plane of bending,
calculated based on the assumption of no lateral
translation. It is taken to be equal to 1.0, conservatively. The Overwrites can be used to change
the value of K1 for the major and minor directions.

K2 =

effective length factor in the plane of bending,
calculated based on a sidesway buckling analysis. The Overwrites can be used to change the
value of K2 for the major and minor directions.

In the expression of B1, the required axial force Pr is used based on its first order value. The magnification factor B1 must be a positive number. Therefore,
αPr must be less than Pe1. If αPr is found to be greater than or equal to Pe1 a
failure condition is declared.

Calculation of Factored Forces and Moments 3 - 21

Steel Frame Design AISC 360-05

If the program assumptions are not satisfactory for a particular structural model
or member, the user has the choice to explicitly specify the values of B1 for any
member.
Currently, the program does not calculate the B2 factor. The user is required to
overwrite the values of B2 for the members.

3.5

Calculation of Nominal Strengths
The nominal strengths in compression, tension, bending, and shear are computed for Compact, Noncompact, and Slender members in accordance with the
following sections. The nominal flexural strengths for all shapes of sections
are calculated based on their principal axes of bending. For the Rectangular, IShape, Box, Channel, Double Channel, Circular, Pipe, T-Shape, and Double
Angle sections, the principal axes coincide with their geometric axes. For the
Single Angle sections, the principal axes are determined and all computations
except shear are based on that.
For all sections, the nominal shear strengths are calculated for directions
aligned with the geometric axes, which typically coincide with the principal
axes. Again, the exception is the Single Angle section.
If the user specifies nonzero nominal capacities for one or more of the
members on the Steel Frame Overwrites form, those values will override
the calculated values for those members. The specified capacities should
be based on the principal axes of bending for flexure, and the geometric
axes for shear.

3.5.1 Nominal Tensile Strength
This section applies to the members subject to axial tension.
Although there is no maximum slenderness limit for members designed to resist tension forces, the slenderness ratio preferably should not exceed 300
(AISC D1). A warning message to that effect is printed for such slender elements under tension.
The design tensile strength, φtPn, and the allowable tensile strength, Pn Ωt , of
tension members is taken as the lower value obtained according to the limit

3 - 22

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

states of yielding of gross section under tension and tensile rupture in the net
section.

3.5.1.1 Tensile Yielding in the Gross Section
Pn = Fy Ag

(AISC D2-1)

φ1 = 0.90 (LRFD)

(AISC D2)

Ωt = 1.67 (ASD)

(AISC D2)

3.5.1.2 Tensile Rupture in the Net Section
Pn = Fu Ae

(AISC D2-2)

φ1 = 0.75 (LRFD)

(AISC D2)

Ωt = 2.00 (ASD)

(AISC D2)

The effective net area, Ae, is assumed to be equal to the gross cross-sectional
area, Ag, by default. For members that are connected with welds or members
with holes, the Ae A g ratio must be modified using the steel frame design
Overwrites to account for the effective area.

3.5.2 Nominal Compressive Strength
The design compressive strength, φcPn, and the allowable compressive
strength, Pn Ωc , of members subject to axial compression are addressed in this
section. The resistance and safety factors used in calculation of design and allowable compressive strengths are:
φc = 0.90 (LRFD)

(AISC E1)

Ωc = 1.67 (ASD)

(AISC E1)

In the determination, the effective length factor K2 is used as the K-factor. If
the chosen analysis method in the Preferences is the General Second Order
Elastic Analysis, the First Order Analysis using Amplified First Order Analysis, or the Limited First Order Analysis, the calculated K2 factors are used. If
the user overwrites the K2 factors, the overwritten values are used. If the chosen analysis method is one of any Direct Analysis Methods, the effective

Calculation of Nominal Strengths 3 - 23

Steel Frame Design AISC 360-05

length factor, K, for calculation of Pn is taken as one (AISC App 7.1). The
overwritten value of K2 will have no effect for the latter case.
The nominal axial compressive strength, Pn , depends on the slenderness ratio,
Kl r , where
K l K l 
Kl
= max  33 33 , 22 22  .
r
r22 
 r33

For all sections except Single Angles, the principal radii of gyration r22 and r33
are used. For Single Angles, the minimum (principal) radius of gyration, rz , is
used instead of r22 and r33 , conservatively, in computing Kl r . K33 and K22 are
two values of K2 for the major and minor axes of bending.
Although there is no maximum slenderness limit for members designed to resist compression forces, the slenderness ratio preferably should not exceed 200
(AISC E2). A warning message to that effect is given for such slender elements
under compression.
The members with any slender element and without any slender elements are
handled separately.
The limit states of torsional and flexural-torsional buckling are ignored for
closed sections (Box and Pipe sections), solid sections, general sections, and
sections created using Section Designer.

3.5.2.1 Members without Slender Elements
The nominal compressive strength of members with compact and noncompact
sections, Pn , is the minimum value obtained according to the limit states of
flexural buckling, torsional and flexural-torsional buckling.

3.5.2.1.1 Flexural Buckling
For compression members with compact and noncompact sections, the nominal
compressive strength, Pn , based on the limit state of flexural buckling, is given
by
Pn = Fcr Ag.
The flexural buckling stress, Fcr , is determined as follows:

3 - 24

Calculation of Nominal Strengths

(AISC E3-1)

Chapter 3 - Design using ANSI/AISC 360-05

Fy

Fe
0.658


Fcr =  

 0.877 Fe ,



 Fy ,


KL
E
≤ 4.71
,
r
Fy

KL
E
> 4.71
,
r
Fy

(AISC E3-2, E3-3)

where Fe is the elastic critical buckling stress given by
Fe =

π2 E
 KL 
 r 



(AISC E3-4)

3.5.2.1.2 Torsional and Flexural-Torsional Buckling
For compression members with compact and noncompact sections, the nominal
compressive strength, Pn , based on the limit state of torsional and flexuraltorsional buckling is given by
Pn = Fcr Ag

(AISC E4-1)

where Ag is the gross area of the member. The flexural buckling stress, Fcτ , is
determined as follows.

3.5.2.1.2.1 Box, Pipe, Circular, Rectangular, General and Section Designer Sections
The limit states of torsional and flexural-torsional buckling are ignored for
members with closed sections, such as Box and Pipe sections, solid sections
(Circular and Rectangular), General sections and sections created using the
Section Designer.

3.5.2.1.2.2 Double Angle and T-Shapes
 F + Fcrz
=
Fcr  cr 22
2H


4 Fcr 22 Fcrz H
 
 1 − 1 −
2

( Fcr 22 + Fcrz )


,



(AISC E4-2)

where,

Calculation of Nominal Strengths 3 - 25

Steel Frame Design AISC 360-05

Fcr 22

Fe =

Fy

(0.658 Fe )Fy ,

=

 0.877 Fe ,


π2 E
 KL22 


 r22 

Fcrz =

KL22
E
,
≤ 4.71
r22
Fy

(AISC E3-2, E3-3)

KL22
E
,
> 4.71
r22
Fy

, and

(AISC E3-4)

GJ
.
Ag r0 2

(AISC E4-3)

3.5.2.1.2.3 I-Shape, Double Channel, Channel, Single Angle Sections
For I-Shape, Double Channel, Channel, and Single Angle sections, Fcτ is calculated using the torsional or flexural-torsional elastic buckling stress, Fe , as follows:
Fy

Fe
0.658


Fcr =  

 0.877 Fe ,



 Fy ,


KL
E
≤ 4.71
,
r
Fy

(AISC E3-2, E3-3, E-4b)

KL
E
> 4.71
if
.
r
Fy

where Fe is calculated from the following equations:
3.5.2.1.2.3.1

I-Shapes and Double Channel Sections

 π2 EC
 1 
w

Fe 
GJ
=
+

2
 ( K z Lz )
  I 22 +I 33 



3.5.2.1.2.3.2

 F + Fez
=
Fe  e33
 2H

3 - 26

(AISC E4-4)

Channel Sections

4 Fe33 Fez H
 
 1 − 1 −
2

( Fe33 + Fez )

Calculation of Nominal Strengths






(AISC E4-5)

Chapter 3 - Design using ANSI/AISC 360-05

3.5.2.1.2.3.3

Single Angle Sections with Equal Legs

 F + Fez
=
Fe  e33
 2H

3.5.2.1.2.3.4

4 Fe33 Fez H
 
 1 − 1 −
2

( Fe33 + Fez )






(AISC E4-5)

Single Angle Sections with Unequal Legs

Fe is the lowest root of the cubic equation.
2

x 
y
( Fe − Fe33 )( Fe − Fe22 ) ( Fe − Fez ) − Fe2 ( Fe − Fe22 )  o  − Fe2 ( Fe − Fe33 )  o
 r0 
 r0


0
=


(AISC E4-6)
In the preceding equations,
Cw

is the warping constant, in6 (mm6)

x0, y0

are the coordinates of the shear center with respect to the centroid, x0 = 0 for Double Angle and T-Shaped members (y-axis
symmetry)

xo2 + yo2 +

I 22 + I 33
polar radius of gyration about the shear
=
Ag

center
H

(AISC E4-7)

 x 2 + y2 
= 1−  o 2 o 
 r


Fe33 =

Fe 22 =

π2 E

( K33 L33

r33 )

π2 E

( K 22 L22

r22 )

 π2 EC
 1
w
+ GJ  2
Fez = 
2
 ( K z Lz )
 Ar0
K22, K33

(AISC E4-8)

(AISC E4-9)

(AISC E4-10)

(AISC E 4-11)

are effective length factors K2 in minor and major directions

Calculation of Nominal Strengths 3 - 27

Steel Frame Design AISC 360-05

is the effective length factor for torsional buckling, and it is
taken equal to KLTB in this program; it can be overwritten

L22, L33

are effective lengths in the minor and major directions

r22, r33

are the radii of gyration about the principal axes

is the effective length for torsional buckling and it is taken
equal to L22 by default, but it can be overwritten.

For angle sections, the principal moment of inertia and radii of gyration
are used for computing Fe. Also, the maximum value of KL, i.e.,
max(K22L22, K33L33), is used in place of K22L22 or K33 L33 in calculating
Fe22 and Fe33 in this case. The principal maximum value rmax is used for
calculating Fe33 , and the principal minimum value rmin is used in calculating Fe22.

3.5.2.2 Members with Slender Elements
The nominal compressive strength of members with slender sections, Pn , is the
minimum value obtained according to the limit states of flexural, torsional and
flexural-torsional buckling.

3.5.2.2.1 Flexural Buckling
For compression members with slender sections, the nominal compressive
strength, Pn , based on the limit state of flexural buckling, is given by
Pn = Fcr Ag.

(AISC E7-1)

The flexural buckling stress, Fcr , is determined as follows:
QFy
 
Q  0.658 Fe

Fcr =  

0.877 Fe ,


 Fy , if Fe ≥ 0.44QFy , and



(AISC E7-2, E7-3)

if Fe < 0.44QFy ,

where Fe is the elastic critical buckling stress for flexural buckling limit state.

3 - 28

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

Fe =

π2 E
 KL 
 r 



(AISC E3-4)

3.5.2.2.2 Torsional and Flexural-Torsional Buckling
For compression members with slender sections, the nominal compressive
strength, Pn , based on Torsional and Flexural-Torsional limit state is given by:
Pn = Fcr Ag , where

(AISC E7-1)

Fcr is determined as follows:
QFy
 
Q  0.658 Fe
Fcr =  


0.877 Fe


 Fy if Fy ≥ 0.44QFy , and


if Fy < 0.44 Fy ,

(AISC E7-2, E7-3)

where, Fe is the elastic critical buckling stress for torsional and flexuraltorsional limit states, which are given for different shapes as follows.

3.5.2.2.2.1 Box, Pipe, Circular, Rectangular, General and Section Designer Sections
The limit states of torsional and flexural-torsional buckling are ignored for
members with closed (Box and Pipe), solid (Circular and Rectangular), General
sections and sections created using the Section Designer.

3.5.2.2.2.2 I-Shape and Double Channel Sections
 π2 EC


1
w
=
Fe 
+ GJ  

2
 ( K 2 L2 )
  I 22 + I 33 

(AISC E7, E4-4)

3.5.2.2.2.3 Channel Sections
 F + Fez
=
Fe  e33
 2H

4 Fe33 Fez H
 
 1 − 1 −
2

( Fe33 + Fez )






(AISC E7, E4-5)

Calculation of Nominal Strengths 3 - 29

Steel Frame Design AISC 360-05

3.5.2.2.2.4 Double Angle Sections and T-Shapes
 F + Fez
=
Fe  e 22
 2H

4 Fe 22 Fez H
 
 1 − 1 −
2

( Fe33 + Fez )






(AISC E7, E4-5)

3.5.2.2.2.5 Single Angle Sections with Equal Legs
 F + Fez
=
Fe  e33
2H


4 Fe33 Fez H

 1 − 1 −
 
( Fe33 + Fez )2





(AISC E7, E4-5)

3.5.2.2.2.6 Single Angle Sections with Unequal Legs
Fe is the lowest root of the cubic equation.
2

x 
y 
0
( Fe − Fe33 )( Fe − Fe22 ) ( Fe − Fez ) − F ( Fe − Fe22 )  o  − Fe2 ( Fe − Fe33 )  o  =
 ro 
 ro 
2
e

(AISC E7, E4-6)
The variables used in the preceding expressions for Fe , such as Cw, x0, y0, ro ,
H, Fe33, Fe22, Fez, K22, K33, Kz, L22, L33, Lz, KL r , and so on, were explained in
the previous section.

3.5.2.2.3 Reduction Factor for Slenderness
The reduction factor for slender compression elements, Q, is computed as follows:
Q = QsQa ,

(AISC E7)

where Qs and Qa are reduction factors for slender unstiffened compression elements (flanges of I-Shapes, T-Shapes, Double Angles, Channels, and Double
Channels; legs of angles; and stems of T-Shapes) and slender stiffened compression elements (webs of I-Shapes, Channels, and Boxes; and Pipe sections),
respectively. For cross-sections composed of only unstiffened slender elements, Q = Qs (Qa = 1) and for cross-sections composed of only stiffened slender elements, Q = Qa (Qs = 1).
The reduction factor, Qs , for slender unstiffened elements is defined as follows:

3.5.2.2.3.1 Flange of I-Shape, T-Shape, Channel and Double Channel
Sections
Rolled:
3 - 30

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05



1.0,



 b  Fy
=
Qs 1.415 − 0.74  
,
t E


 0.69 E ,
  b 2
 Fy  
  t 

b
E
≤ 0.56
,
t
Fy

if 0.56
if

E b
E
< ≤ 1.03
, and
Fy t
Fy

b
E
> 1.03
.
t
Fy

(AISC E7-4, E7-5, E7-6)
Built-Up:


1.0,



 b  Fy
=
Qs 1.415 − 0.65  
,
 t  Ekc


 0.90 Ekc ,
2

b
 Fy  
  t 

Ekc
b
≤ 0.64
,
t
Fy

if 0.64

Ekc b
Ekc
< ≤ 1.17
,
Fy
t
Fy

Ekc
b
> 1.17
,
t
Fy

(AISC E7-7, E7-8, E7-9)
where kc =

4
and 0.35 ≤ kc ≤ 0.76,
h tw

(AISC E7.1b)

and b t is defined as

(
(

 bt

b  b f
=
t b
f

b f

)
2t )

2t f

for I Shapes,
for T Shapes,

(AISC B4.1a, E7.1)

for Channels,

for Double Channels.

Calculation of Nominal Strengths 3 - 31

Steel Frame Design AISC 360-05

3.5.2.2.3.1.1

Legs of Single and Double Angle Sections



1.0,
if



 b  Fy
Q=
, if
1.34 − 0.76  
s
t E


 0.53E ,
if
  b 2
 Fy  
  t 

b
E
≤ 0.45
,
t
Fy
0.45

E b
E
< ≤ 0.91
, and
Fy t
Fy

b
E
> 0.91
,
t
Fy

(AISC E7-10, E7-11, E7-12)
where b is the full width of the longest leg, and t is the corresponding thickness
(AISC B4.1b, E7.1c).
3.5.2.2.3.1.2

Stem of T-Sections



1.0,



Fy
=
Qs 1.908 − 1.22
,
E


 0.69 E ,
  d 2
 Fy  
  t 

d
E
≤ 0.75
,
t
Fy

if 0.75
if

E d
E
< ≤ 1.03
, and
Fy t
Fy

d
E
> 1.03
,
t
Fy

(AISC E7-13, E7-14, E7-15)
where d is the full nominal depth of the tee and t is the thickness of the element
(AISC B4.1d).
For T-Shapes, the Qs is calculated for the flange and web separately, and the
minimum of the two values is used as Qs. For Angle and Double Angle sections, Qs is calculated based on the leg that gives the largest b t and so the
smallest Qs .
The reduction factor, Qa, for slender stiffened elements is defined as follows:

3 - 32

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

Qa =

Aeff
A

(AISC E7-16)

where A is the total cross sectional area of the member, and Aeff is the summation of the effective areas of the cross-section,
Aeff = A − Σ (b − be)t ,
based on the reduced effective width, be , which is determined as follows.
3.5.2.2.3.1.3

Webs of I -Shapes, Channels, and Double Channels


E  0.34 E 
b
≥ 1.49
1.92t
1 ≤ b, if
f  ( b t ) F 
t

be = 

b
if < 1.49
b,
t


E
, and
f

(AISC E7-17)

E
,
f

where f is taken as Fcr with Q = 1.0 (AISC 7.2a), and b is taken for rolled
shapes as the clear distance between flanges less the corner radius, and is taken
for welded shapes as the clear distance between flanges.

3.5.2.2.3.2 Webs and Flanges of Box Sections

E  0.38 E 
1.92t
1 ≤ b,
f  ( b t ) F 

be = 

b,


b
E
, and
≥ 1.40
t
f

(AISC E7-18)

b
E
if < 1.40
,
t
Fy

where f is conservatively taken as Fy (AISC 7.2b). The flange, b, is taken as
bf − 3tw, and for webs, b is taken as h − 3tf (AISC B4.1d). The design wall
thickness is modified for the welding process (AISC B3.12)

3.5.2.2.3.3 Pipe Sections
The reduction factor for slender stiffened elements is given directly by:

Calculation of Nominal Strengths 3 - 33

Steel Frame Design AISC 360-05


1.0,

 0.038E 2

+ ,
Qa =Q =
 Fy ( D t ) 3

1.0,


if D t < 0.11
if 0.11

E
,
Fy

E D
E
< < 0.45 , and (AISC E7-19)
Fy
t
Fy

if D t > 0.45

E
,
Fy

where D is the outside diameter and t is the wall thickness. The design wall
thickness is modified for the welding process (AISC B3.12). If D / t exceeds
0.45 E / Fy , the section is considered to be too slender and it is not designed.

3.5.3 Nominal Flexure Strength
This section applies to members subject to simple bending about one principal
axis. The members are assumed to be loaded in a plane parallel to a principal
axis that passes through the shear center, or restrained against twisting.
The design flexural strength, φbMn, and the allowable flexural strength,
M n Ω b , are determined using the following resistance and safety factors:
φb = 0.90 (LRFD)

(AISC F1(1))

Ωb = 1.67 (ASD)

(AISC F1(1))

When determining the nominal flexural strength about the major principal axis
for any sections for the limit state of lateral-torsional buckling, it is common to
use the term Cb, the lateral-torsional buckling modification factor for nonuniform moment diagram. Cb is calculated as follows:

=
Cb

2.5 M max

12.5 M max
Rm ≤ 3.0,
+ 3M A + 4 M B + 3Mc

(AISC F1-1)

where,
Mmax = absolute value of maximum moment in unbraced segment, kip-in.
(N-mm)
MA

3 - 34

= absolute value of moment at quarter point of the unbraced segment, kip-in. (N-mm)

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

= absolute value of moment at centerline of the unbraced segment,
kip-in. (N-mm)

= absolute value of moment at three-quarter point of the unbraced
segment, kip-in. (N-mm)

= cross-section monosymmetry parameter
= 1.0, doubly symmetric members
= 1.0, singly symmetric member subject to single curvature bending
2

I 
= 0.5 + 2  yc  , singly symmetric members subjected to reverse
 Iy 


curvature bending

= moment of inertia about the principal y-axis, in.4 (mm4)

Iyc

= moment of inertia about y-axis referred to the compression flange,
or if reverse curvature bending, referred to the smaller flange, in.4
(mm4)

1.0,



1.0,

Rm = 

2

I 

yc


0.5 + 2  I  ,
 y 





for Double Channel, Box, Pipe, and
doubly symmetric I Shapes,
for Channel, Tee, Double Angle and singly symmetric
I Shapes subjected to curvature bending, and
for Channel, Tee, Double Angle, and singly symmetric
I Shapes subjected to reverse curvature bending.

If the member is under tension and if the section is doubly symmetric, Cb is increased by a factor fcb where Ra is given as follows:

Pu
(LRFD)
 1+
Pey

Ra = 
1.5Pa

 1 + P (ASD)
ey


(AISC H1.2)

Cb should be taken as 1.0 for cantilevers. However, the program is unable to
detect whether the member is a cantilever. The user should overwrite Cb for
Calculation of Nominal Strengths 3 - 35

Steel Frame Design AISC 360-05

cantilevers. The program also defaults Cb to 1.0 if the minor unbraced length,
l22, is redefined to be more than the length of the member by the user or the
program, i.e., if the unbraced length is longer than the member length. The
Overwrites can be used to change the value of Cb for any member.
The nominal bending strength depends on the following criteria: the geometric
shape of the cross-section; the axis of bending; the compactness of the section;
and a slenderness parameter for lateral-torsional buckling. The nominal bending strength is the minimum value obtained according to the limit states of
yielding, lateral-torsional buckling, flange local buckling, web local buckling,
tension flange yielding as appropriate to different structural shapes. The following sections describe how different members are designed against flexure
in accordance with AISC Chapter F. AISC, in certain cases, gives options in
the applicability of its code section, ranging from F2 to F12. In most cases, the
program follows the path of the sections that gives more accurate results at the
expense of more detailed calculation. In some cases, the program follows a
simpler path. For an easy reference, Table 3-2 shows the AISC sections for the
various scenarios.
Table 3.2 Selection Table for the Application of Chapter F Sections
Section in
Chapter F

3 - 36

Flange
Slenderness

Web
Slenderness

Limit States

Y, LTB

NC, S

LTB, FLB

C, NC, S

Y, LTB, FLB

C, NC, S

Y, LTB, FLB

C, NC, S

C, NC

Y, LTB, FLB, TFY

Cross Section

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

Table 3.2 Selection Table for the Application of Chapter F Sections
Section in
Chapter F

Flange
Slenderness

Web
Slenderness

Limit States

C, NC, S

Y, LTB, FLB, TFY

C, NC, S

Any

Y, FLB

C, NC, S

C, NC

Y, FLB, WLB

N/A

Y, LB

C, NC, S

Any

Y, LTB, FLB

F10

N/A

Y, LTB, LLB

F11

N/A

Any

Y, LTB

Cross Section

F12
Unsymmetrical shapes
Y
= yielding
LTB = lateral-torsional buckling
FLB = flange local buckling
WLB = web local buckling
TFY = tension flange yielding

N/A
N/A
All limit states
LLB = leg local buckling
LB = local buckling
C
= compact or seismically compact
NC = noncompact
S
= slender

3.5.3.1 Doubly Symmetric I-Sections
3.5.3.1.1 Major Axis Bending
The nominal flexural strength for major axis bending depends on compactness
of the web and flanges.

3.5.3.1.1.1 Compact Webs with Compact Flanges
The nominal flexural strength is the lowest value obtained according to the
limit states of yielding (plastic moment) and lateral-torsional buckling.

Calculation of Nominal Strengths 3 - 37

Steel Frame Design AISC 360-05

3.5.3.1.1.1.1

Yielding

Mn = Mp = FyZ33 ,

(AISC F2-1)

where, Z33 is the plastic section modulus about the major axis.
3.5.3.1.1.1.2

Lateral-Torsional Buckling

M p ,

 

=
M n Cb  M p − M p − 0.7 Fy S33
 

 Fcr S33 ≤ M p ,


(

if Lb ≤ L p ,
 Lb − L p  
  ≤ M p , if L p < Lb < Lr , and

 r − L p  

)  L

if L p > Lr ,

(AISC F2-1, F2-2, F2-3)
where, S33 is the elastic section modulus taken about the major axis, Lb is the
unbraced length, Lp and Lr are limiting lengths, and Fcr is the critical buckling
stress. Fcr , Lp , and Lr are given by:

=
Fcr

Jc  Lb 
1 + 0.078
  ,
S33 h0  rts 

Cb π2 E
 Lb 
 
 rts 

L p = 1.76ry

E
,
Fy

=
Lr 1.95rts

E
0.7 Fy

(AISC F2-4)

(AISC F2-5)

 0.7 Fy S33 h0 
Jc
1 + 1 + 6.76 
 ,
S33 h0
Jc 
 E

(AISC F2-6)

where,
rts 2 =

I y Cw
S33

c = 1, and
h0 is the distance between flange centroids.

3 - 38

Calculation of Nominal Strengths

(AISC F2-7)
(AISC F2-8a)

Chapter 3 - Design using ANSI/AISC 360-05

3.5.3.1.1.2 Compact Webs with Noncompact or Slender Flanges
The nominal flexural strength is the lowest value obtained from the limit states
of lateral-torsional buckling and compression flange local buckling.
3.5.3.1.1.2.1

Lateral-Torsional Buckling

The provisions of lateral-torsional buckling for "Compact Web and Flanges" as
described in the provision pages also apply to the nominal flexural strength of
I-Shapes with compact webs and noncompact or slender flanges bent about
their major axis.
M p ,

 

=
M n Cb  M p − M p − 0.7 Fy S33
 

 Fcr S33 ≤ M p ,


(

if Lb ≤ L p ,
 Lb − L p  
  ≤ M p , if L p < Lb < Lr , and

 r − L p  

)  L

if L p > Lr .

(AISC F3.1, F2-1, F2-2, F2-3)
3.5.3.1.1.2.2

Compression Flange Local Buckling


 M p − M p − 0.7 Fy S33

Mn = 
 0.9 Ekc S33
,

λ2


(

 λ − λ pf 
 , for noncompact flanges,

−
λ
rf
pf



)  λ

for slender flanges,

(AISC F3-1, 3-2)
where λ, λpf , and λrf are the slenderness and limiting slenderness for compact
and noncompact flanges from Table 3.5, respectively,
λ=

bf
2t f

0.38
λ pf =

E
,
Fy

(AISC Table B4.1, F3.2)

Calculation of Nominal Strengths 3 - 39

Steel Frame Design AISC 360-05


E
(Rolled),
1.0
Fy

λ rf =

kc E

0.95 F (Welded),
L


(AISC Table B4.1, F3.2)

and kc is given by

kc =

4
, 0.35 ≤ kc ≤0.76.
h tw

(AISC F.3.2)

3.5.3.1.1.3 Noncompact Webs with Compact, Noncompact and Slender
Flanges
The nominal flexural strength is the lowest values obtained from the limit
states of compression flange yielding, lateral-torsional buckling, and compression flange local buckling.
3.5.3.1.1.3.1

Compression Flange Yielding

Mn = RpcMy,

(AISC F4-1)

where, Rpc is the web plasticity factor, which is determined as follows:
 Mp
,

M
y

R pc = 
  M p −  M p − 1  λ − λ pw

  M y  M y


 λ rw − λ pw
 

if
 M p
≤
, if
  M y
 

λ ≤ λ pw ,
λ pw < λ w ≤ λ rw ,

(AISC F4-9a, F4-9b)
where,
Mp = Z33Fy ≤ 1.6S33Fy

(AISC F4-2)

S33 = elastic section modulus for major axis bending

λw =

hc
tw

(AISC F4.2, Table B4.1)

λ pw = λ p , the limiting slenderness for a compact web, as given in
Table 3-5
3 - 40

Calculation of Nominal Strengths

(AISC Table B4.1)

Chapter 3 - Design using ANSI/AISC 360-05

λrw = λr, the limiting slenderness for a noncompact web, as given in
Table 3-5
(AISC Table B4.1)
and My is the yield moment, which is determined as follows:
My = S33Fy
3.5.3.1.1.3.2

(AISC F4-1)

Lateral-Torsional Buckling

 R pc M y ,

 

=
M n Cb  R pc M y − R pc M y − FL S33
 

 Fcr S33 ≤ R pc M y ,


(

if Lb ≤ L p ,
 Lb − L p  
  ≤ R pc M y ,

−
L
r
p



)  L

if L p < Lb ≤ Lr ,
if Lb > Lr ,

(AISC F4-1, F4-2, F4-3)
where,
Fcr
=

rt =

=
aw

J L 
1 + 0.078 c  b 
S33 ho  rt 

Cb π2 E
 Lb 
 
 rt 

(AISC F4-5)

(AISC F4-10)

h 1
h2 
12  0 + aw

 d 6 h0 d 

hc t w
≤ 10
bf t f

(AISC F4-11)

1, if I yc I y > 0.23
C=
0, if I yc I y ≤ 0.23

(AISC F4.2)

E
Fy

(AISC F4-7)

L p = 1.1rt

E
=
Lr 1.95rt
FL

J
F S h 
1 + 1 + 6.76  L 33 o 
S33 ho
 E J 

(AISC F4-8)

Calculation of Nominal Strengths 3 - 41

Steel Frame Design AISC 360-05

FL = 0.7Fy

(AISC F4-6a)

Rpc = web plastification factor, which is determined using a formula de-

scribe previously (AISC F4-9)
Iyc = moment of inertia of the compression flange about the minor axis
Iy

3.5.3.1.1.3.3

= moment of inertia of the entire section about the minor axis.

Compression Flange Local Buckling


 R pc M y ,

 
 λ − λ pt
M n =   R pc M y − ( R pc M y − FL S33 ) 
 λ rf − λ pt
 


 0.9 Ekc S33 ,

λ2

if flanges are compact,

  , if flanges are noncompact, and
 
if flanges are slender,

(AISC F4-1, F4-12, F4-13)
where,
FL

= 0.7Fy

(AISC F4-6a, F4.3)

Rpc = is the web plastification factor, which is determined using a formula described previously (AISC F4-9, F4.3)
kc

4
h tw

35 ≤ kc ≤ 0.76

(AISC F4.3, Table B4.1)

bf
2t f

λpf = λp , the limiting slenderness for compact flange, as given in Table
3-5 (AISC Table B4.1, B4.3)
λrf

3 - 42

= λr , the limiting slenderness for noncompact flange, as given in Table 3-5 (AISC Table B4.1, B4.3).

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

3.5.3.1.1.4 Slender Webs with Compact, Noncompact, and Slender
Flanges
The nominal flexural strength is the lowest value obtained from the limit states
of compression flange yielding, lateral-torsional buckling, and compression
flange local buckling.
3.5.3.1.1.4.1

Compression Flange Yielding

Mn = RpgFyS33 ,

(AISC F5-1)

where Rpg is the bending strength reduction factor given by
aw
1−
R pg =
1200 + 300 aw

=
aw

h
E 
 c − 5.7
 ≤ 1.0,
 tw

F
y



ht w
≤ 10,
bf t f

(AISC F5-6)

(AISC F5.2, F4-11)

where h0 is the distance between flange centroids (AISC F2.2).
3.5.3.1.1.4.2

Lateral-Torsional Buckling

Mn = RpgFcrS33 ,

(AISC F5-2)

where Fcr is the critical lateral-torsional buckling stress given by



F ,
 y

 
Fcr Cb  Fy − 0.3Fy
=
 

 Cb π2 E
≤ Fy ,

2
 Lb 
 
  rt 

(

if Lb ≤ L p ,
 Lb − L p  
  ≤ Fy , if L p < Lb ≤ Lr , and

L
−
r
p



)  L

if L p > Lr ,

(AISC F5-1, F5-3, 5-4)
where,

Calculation of Nominal Strengths 3 - 43

Steel Frame Design AISC 360-05

L p = 1.1rt

E
Fy

Lr = πrt

E
0.7 Fy

rt =

(AISC F5.2, 4-7)

(AISC F5-5)

(AISC F5.2, F4-10)

h 1
h2 
12  0 + aw

 d 6 h0 d 

Rpg is the bending strength reduction factor, which has been described in the
previous section.
3.5.3.1.1.4.3

Compression Flange Local Buckling

Mn = RpgFcrS33 ,

(AISC F5-7)

where Fcr is the critical buckling stress given by



F ,
 y


 λ − λ pf

Fcr   Fy − 0.3Fy 
=
 λ rf − λ pf
 


 0.9 Ekc
≤ Fy ,

2
  bf 

 
  2t f 


(

)

if flanges are compact,

  , if flanges are noncompact, and


if flanges are slender,

(AISC F5-1, F5-8, F5-9)
and λ, λpf, and λrf are the slenderness and the limiting slenderness ratios for
compact and noncompact flanges from Table 3.5, respectively, and kc is given
by

kc =

3 - 44

4
where 0.35 ≤ kc ≤ 0.76.
h tw

Calculation of Nominal Strengths

(AISC 5.3)

Chapter 3 - Design using ANSI/AISC 360-05

3.5.3.1.2 Minor Axis Bending
The nominal flexural strength is the lower value obtained according to the limit
states of yielding (plastic moment) and flange local buckling.

3.5.3.1.2.1 Yielding
Mn = Mp = FyZ22 ≤ 1.6FyS22,

(AISC F6-1)

where S22 and Z22 are the section and plastic moduli about the minor axis, respectively.

3.5.3.1.2.2 Flange Local Buckling
M p ,


M n =  M p − M p − 0.7 Fy S22

F S ,
 cr 22

(

for compact flange,
 λ − λ pf 
,

 rf − λ pf 

)  λ

for noncompact flanges, and
for slender flanges,

(AISC F6-1, F6-2, F6-3)
where,
Fcr =

λ=

0.69 E
λ2

(AISC 6-4)

(AISC F6.2)

2t f

and λpf and λrf are the limiting slendernesses for compact and noncompact
flanges, respectively, as described in Table 3-5 (AISC B4.1).

3.5.3.2 Singly Symmetric I-Sections
3.5.3.2.1 Major Axis Bending
The nominal of flexural strength for major axes bending depends on compactness of the web and flanges.

3.5.3.2.1.1 Compact and Noncompact Webs with Compact, Noncompact
and Slender Flanges
The nominal flexural strength is the lowest values obtained from the limit sates
of compression flange yielding, lateral-torsional buckling, compression flange
local buckling, and tension flange yielding.
Calculation of Nominal Strengths 3 - 45

Steel Frame Design AISC 360-05

3.5.3.2.1.2 Compression Flange Yielding
Mn = RpcMyc,

(AISC F4-1)

where, Rpc is the web plasticity factor, which is determined as follows:
 Mp
,

M
yc

R pc = 
  M p −  M p − 1  λ − λ pw

  M yc  M yc
 λ rw − λ pw


 

if
 M p
, if
  ≤
  M yc

λ ≤ λ pw ,
λ pw < λ w ≤ λ rw ,

(AISC F4-9a, F4-9b)
where,
Mp = Z33Fy ≤ 1.6S33cFy

(AISC F4-2)

S33c = elastic section modulus for major axis bending referred to
compression flange
S33t = elastic section modulus for major axis bending referred to tension flange
λ

hc
tw

(AISC F4.2, Table B4.1)

λpw = λp, the limiting slenderness for a compact web, as given in
Table 3-5
(AISC Table B4.1)
λrw = λr , the limiting slenderness for a noncompact web, as given in
Table 3-5
(AISC Table B4.1)
and Myc is the yield moment for compression flange yielding, which is
determined as follows:
Myc = S33cFy.

3 - 46

Calculation of Nominal Strengths

(AISC F4-1)

Chapter 3 - Design using ANSI/AISC 360-05

3.5.3.2.1.3 Lateral-Torsional Buckling
 R pc M yc ,

 

=
M n Cb  R pc M yc − R pc M yc − FL S33c
 

 Fcr S33c ≤ R pc M yc ,


(

if Lb ≤ L p
 Lb − L p  
  ≤ R pc M yc , if L p < Lb ≤ Lr ,

 r − L p  

)  L

if Lb > Lr ,

(AISC F4-1, F4-2, F4-3)
where,
Fcr
=

rt =

=
aw

J L 
1 + 0.078 c  b 
S33 ho  rt 

Cb π2 E
 Lb 
 
 rt 

(AISC F4-5)

b fc

(AISC F4-10)

h 1
h2 
12  0 + aw

 d 6 h0 d 

hc t w
≤ 10
b fe t fc

(AISC F4-11)

1, if I yc I y > 0.23
C=
0, if I yc I y ≤ 0.23

(AISC F4.2)

E
Fy

(AISC F4-7)

L p = 1.1rt

E
=
Lr 1.95rt
FL

J
F S h 
1 + 1 + 6.76  L 33c o 
S33 ho
 E J 


0.7 Fy ,

FL = 
 S33t F ≥ 0.5F ,
y
 S33c y

S33t
≥ 0.7
S33c

S
if 33t ≤ 0.7
S33c

(AISC F4-8)

(AISC F4-6a, F4-6b)

Calculation of Nominal Strengths 3 - 47

Steel Frame Design AISC 360-05

Rpc = web plastification factor, which is determined using a formula

describe previously (AISC F4-9)
Iyc = moment of inertia of the compression flange about the minor axis
Iy = moment of inertia of the section about the minor axis.

3.5.3.2.1.4 Compression Flange Local Buckling

 R pc M yc ,

 λ − λ pt
 
M n =   R pc M yc − ( R pc M yc − FL S33c ) 

 
 λ rf − λ pt

 0.9 Ekc S33c ,
λ2


if flanges are compact,

  , if flanges are noncompact, and
 
if flanges are slender,

(AISC F4-1, F4-12, F4-13)
where,
FL

is a calculated stress, which has been defined previously
(AISC F4-6a, F4-6b, F4.3)

Rpc =

is the web plastification factor, which is determined using a
formula described previously (AISC F4-9, F4.3)

4
h tw

, 35 ≤ kc ≤ 0.76

(AISC F4.3, Table B4.1)

b fc
2t fc

λpf =

λp , the limiting slenderness for compact flange, as given in
Table 3-5 (AISC Table B4.1, B4.3)

λrf

λr , the limiting slenderness for noncompact flange, as given
in Table 3-5 (AISC Table B4.1, B4.3).

3.5.3.2.1.5 Tension Flange Yielding
 M p ,
Mn = 
 R pt M yt ,
3 - 48

if S33t ≥ S33c
if S33t < S33c

Calculation of Nominal Strengths

(AISC F4-14)

Chapter 3 - Design using ANSI/AISC 360-05

where, Rpt is the web plastification factor corresponding to the tension flange
yielding limit state. It is determined as follows:

 Mp
,

 M yt
R pt 
 M p −  M p − 1  λ − λ pw

 M yt  M yt
 λ rw − λ pw




if λ ≤ λ pw

 , if λ pw < λ ≤ λ rw

(AISC F4-15a, F4-15b)

where,
Mp

= Z33Fy

(AISC F4-2)

S33c = elastic section modulus for major axis bending referred to
compression flange
S33t = elastic section modulus for major axis bending referred to tension flange
λw

hc
tw

(AISC F4.2, Table B4.1)

λwp = λp , the limiting slenderness for a compact web, as given in
Table 3-5
(AISC Table B4.1)
λrw = λr , the limiting slenderness for a noncompact web, as given in
Table 3-5.
(AISC Table B4.1)

3.5.3.2.1.6 Slender Webs with Compact, Noncompact and Slender Flanges
The nominal flexural strength is the lowest value obtained from the limit states
of compression flange yielding, lateral-torsional buckling, compression flange
local buckling, and tension flange yielding.
3.5.3.2.1.6.1

Compression Flange Yielding

Mn = RpgFyS33c ,

(AISC F5-1)

where, Rpg is the bending strength reduction factor given by

Calculation of Nominal Strengths 3 - 49

Steel Frame Design AISC 360-05

aw
R pg =
1−
1200 + 300 aw

=
aw

h
E 
 c − 5.7
 ≤ 1.0
 tw
Fy 



ht w
≤ 10
bf t f

(AISC F5-6)

(AISC F5.2, F4-11)

where, h0 is the distance between flange centroids (AISC F2.2).
3.5.3.2.1.6.2

Lateral-Torsional Buckling

Mn = RpgFcrS33c ,

(AISC F5-2)

where, Fcr is the critical lateral-torsional buckling stress given by



F ,
 y

 
Fcr Cb  Fy − 0.3Fy
=
 

 Cb π2 E
≤ Fy ,

2
 Lb 
 
  rt 

(

if Lb ≤ L p ,
 Lb − L p  
  ≤ Fy , if L p < Lb ≤ Lr , and

 r − L p  

)  L

if L p > Lr ,

(AISC F5-1, F5-3, 5-4)
where,
L p = 1.1rt

E
Fy

Lr = πrt

E
0.7 Fy

rt =

3 - 50

(AISC F5.2, 4-7)

bfc
h 1
h2 
12  0 + aw

h0d 
d 6

Calculation of Nominal Strengths

(AISC F5-5)

(AISC F5.2, F4-10)

Chapter 3 - Design using ANSI/AISC 360-05

Rpg is the bending strength reduction factor, which has been described
in a previous section.
3.5.3.2.1.6.3

Compression Flange Local Buckling

Mn = RpgFcrS33c ,

(AISC F5-7)

where, Fcr is the critical buckling stress given by



F ,
 y


 λ − λ pf

=
Fcr   Fy − 0.3Fy 
 λrf − λ pf
 


 0.9Ekc
≤ Fy ,

2
  b fc 

 

  2t fc 

(

)

if flanges are compact ,

  , if flanges are noncompact, and


if flanges are slender,

(AISC F5-1, F5-8, F -9)
and λ, λpf, and λrf are the slenderness and the limiting slenderness ratios for
compact and noncompact flanges from Table 3.5, respectively, and kc is given
by

kc =

4
, where 0.35 ≤ kc ≤ 0.76.
h tw

3.5.3.2.1.6.4

(AISC 5.3)

Tension Flange Yielding

if S33t ≥ S33c ,

M p
Mn = 

 Fy S33t if S33t < S33c .

(AISC F5-10)

3.5.3.2.2 Minor Axis Bending
The nominal flexural strength is the lower value obtained according to the limit
states of yielding (plastic moment) and flange local buckling.

3.5.3.2.2.1 Yielding
Mn = Mp = Fy Z22 ≤ 1.6Fy S22,

(AISC F6-1)

Calculation of Nominal Strengths 3 - 51

Steel Frame Design AISC 360-05

where, S22 and Z22 are the section and plastic moduli about the minor axis, respectively.

3.5.3.2.2.2 Flange Local Buckling
M p ,


M n =  M p − M p − 0.7 Fy S22

F S ,
 cr 22

(

for compact flange,
 λ − λ pf 
,

 rf − λ pf 

)  λ

for noncompact flanges, and
for slender flanges,

(AISC F6-1, F6-2, F6-3)
where,
0.69 E
λ2

(AISC 6-4)

 b fb b ft 
λ =max  , 
 ttb t ft 

(AISC F6.2)

Fcr =

and λpf and λrf are the limiting slendernesses for compact and noncompact
flanges, respectively, as described in Table 3-5 (AISC B4.1).

3.5.3.3 Channel and Double Channel Sections
3.5.3.3.1 Major Axis Bending
The nominal flexural strength is the lowest value obtained according to the
limit states of yielding (plastic moment), lateral-torsional buckling, and compression flange local buckling.

3.5.3.3.1.1 Yielding
Mn = Mp =Fy Z33 ,
where Z33 is the plastic section modulus about the major axis.

3 - 52

Calculation of Nominal Strengths

(AISC F2-1)

Chapter 3 - Design using ANSI/AISC 360-05

3.5.3.3.1.2 Lateral-Torsional Buckling
M p ,

 

=
M n Cb  M p − M p − 0.7 Fy S33
 

 Fcr S33 ≤ M p ,


(

if Lb ≤ L p ,
 Lb − L p  
  ≤ M p if L p < Lb < Lr , and

 r − L p  

)  L

if L p > Lr ,

(AISC F2-1, F2-2, F2-3)
where S33 is the elastic section modulus taken about the major axis, Lb is the
unbraced length, Lp and Lr are limiting lengths, and Fcr is the critical buckling
stress. Fcr , Lp and Lr are given by

=
Fcr

Cb π2 E
 Lb 
 
 rts 

1 + 0.078

Jc
S33 h0

 Lb 
 
 rts 

(AISC F2-4)

E
Fy

L p = 1.76ry

(AISC F2-5)

E
=
Lr 1.95rts
0.7 Fy

 0.7 Fy S33 h0 
Jc
1 + 1 + 6.76 

S33 h0
Jc 
 E

(AISC F2-6)

where
rts 2 =

I y Cw

(AISC F2-7)

S33

1

C =  ho
2


for Double Channel sections
Iy
Cw

for Channel sections

(AISC F2-8a, F2-8b)

and h0 is the distance between flange centroids.

Calculation of Nominal Strengths 3 - 53

Steel Frame Design AISC 360-05

3.5.3.3.1.3 Compression Flange Local Buckling
The nominal strength for compression flange local buckling is determined
based on whether the web is compact, noncompact, or slender.
If the web is compact,

M p ,


M n =  M p − M p − 0.7 Fy S33

 0.9 Ek S
c 33

,

λ2

(

for compact flanges,
 λ − λ pf 
,

 rf − λ pf 

)  λ

for noncompact flanges, and
for slender flanges,

(AISC F2-1, F3-1, F3-2)
if the web is noncompact,

 R pc M y ,


M n =  R pc M y − R pc M y − FL S33

 0.9 Ek S
c 33

,

λ2

(

for compact flange,
 λ − λ pf 
,

 rf − λ pf 

)  λ

for noncompact flanges, and
for slender flanges,

(AISC F4-1, F4-12, F4-13)
and if the web is slender,
Mn = RpgFcr S33

(AISC F5-7)

where, Fcr is the critical buckling stress give by

 Fy ,

 λ − λ pf

F
=
 Fy − ( 0.3Fy ) 
cr

 λ rf − λ pf
 0.9 Ek
c

≤ Fy ,
 λ2

where,
3 - 54

Calculation of Nominal Strengths

if flanges are compact,

 , if the flanges are noncompact,

if the flanges are slender,

Chapter 3 - Design using ANSI/AISC 360-05

λpf

= λp , the limiting slenderness for compact flange, as given in Table
3-5 (AISC Table B4.1, B4.3)

λrf

= λr , the limiting slenderness for noncompact flange, as given in
Table 3-5 (AISC Table B4.1, B4.3)

= 0.7Fy

Rpc

2t f

4
h tw

, 35 ≤ kc ≤ 0.76

 Mp
,

 My
= 
  M p −  M p − 1  λ − λ pw

  M y  M y
 λ rw − λ pw


 

(AISC F4.3, Table B4.1)
(AISC F4-6a, F4.3)
if λ w ≤ λ pw
 M p
,
  ≤
M
y



if λ pw < λ w ≤ λ rw

(AISC F4-9a, F4-9b)
Rpg = 1 −

 hc
aw
E 
 − 5.7
 ≤ 1.0
Fy 
1200 + 300 aw  t w

(AISC F5-6)

S33 = elastic section modulus for major axis bending,
λw

hc
tw

λpw = λp , the limiting slenderness for compact web, as given in Table 3-5
(AISC Table B4.1)
λrw = λr , the limiting slenderness for a noncompact web, as given in
Table 3-5 (AISC Table B4.1)
Rpg is the bending strength reduction factor, which has been described in a
previous section.

Calculation of Nominal Strengths 3 - 55

Steel Frame Design AISC 360-05

3.5.3.3.2 Minor Axis Bending
The nominal flexural strength is the lower value obtained according to the limit
states of yielding (plastic moment) and flange local buckling.

3.5.3.3.2.1 Yielding
Mn = Mp = Fy Z22 ≤ 1.6Fy S22

(AISC F6-1)

where, S22 and Z22 are the section and plastic moduli about the minor axis, respectively.

3.5.3.3.2.2 Flange Local Buckling
M p ,


M n =  M p − M p − 0.7 Fy S22

F S ,
 cr 22

(

for compact flange,
 λ − λ pf 
,

 rf − λ pf 

)  λ

for noncompact flanges, and
for slender flanges,

(AISC F6-1, F6-2, F6-3)
where,

Fcr =
λ=

0.69 E
λ2

bf
2t f

(AISC 6-4)

(AISC F6.2)

and λpf and λrf are the limiting slendernesses for compact and noncompact
flanges, respectively, as described in Table 3-5 (AISC B4.1).

3.5.3.4 Box Sections
This section applies to Box sections with compact or noncompact webs and
compact, noncompact or slender flanges, bent about either axis. The program
uses the same set of formulas for both major and minor direction bending, but
with appropriate parameters.
The nominal flexural strength is the lowest value obtained according to the
limit states of yielding (plastic moment), flange local buckling and web local
buckling.

3 - 56

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

3.5.3.4.1 Yielding
Mn = Mp = FyZ,

(AISC F7-1)

where, Z is the plastic section modulus about the axis of bending.

3.5.3.4.2 Flange Local Buckling
 M p,



b
=
M n  M p − ( M p − Fy S )  3.57

t



 Fy Seff ,

for compact flanges,
Fy
E





− 4.0  ≤ M p , for noncompact flanges, and
for slender flanges,

(AISC F7-1, F7-2, F7-3)
where, Seff is the effective section modulus determined using the effective compressive flange width, be ,
be = 1.92t

E
Fy

 0.38 E 
1 −
 ≤ b.
b t Fy 


(AISC F7-4)

See the "Reduction Factor for Slenderness" section for details (AISC F7, E7.2).

3.5.3.4.3 Web Local Buckling


M p ,



h
M
=
 M p − ( M p − Fy S33 )  0.305
n
tw




h

 M p − ( M p − Fy S33 )  0.305 t
w



for compact webs, and



E


Fy
− 0.738  ≤ M p , for slender webs.

E

(AISC F7-1, F7-5)
Fy

− 0.738  ≤ M p , for noncompact webs,

Note that the code does not cover the Box section flexure strength if the web is
slender. The program uses the same flexure strength formula for Box sections
with noncompact and slender webs, even though the formula applies only to
noncompact section.

Calculation of Nominal Strengths 3 - 57

Steel Frame Design AISC 360-05

3.5.3.5 Pipe Sections
This section applies to pipe sections with D t ratio less than

0.45E
. If a Pipe
Fy

section violates this limit, the program reports an error.
The nominal flexural strength is the lowest value obtained according to the
limit states of yielding (plastic moment) and local buckling. The same set of
formulas is used for both major and minor axes of bending.

3.5.3.5.1 Yielding
Mn = Mp = FyZ

(AISC F8-1)

3.5.3.5.2 Local Buckling
for compact sections,
M p ,




 0.021E
M n = 
+ Fy  S , for noncompact sections, and (AISC F8-1, F8-2, F8-3)

 D

 t
 F S,
for slender sections,
 cr

where, S is the elastic section modulus and Fcr is the critical buckling stress,
where,
Fcr =

0.33E
.
D
t

(AISC F8-4)

3.5.3.6 T-Shapes and Double Angle Sections
3.5.3.6.1 Major Axes Bending
The nominal flexural strength for T-Shapes and Double Angles bent about their
major (3-3) axis, i.e., the axis perpendicular to the axis of symmetry, is taken as
the lowest value obtained according to the limit states of yielding (plastic moment), lateral-torsional buckling, and flange local buckling.

3 - 58

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

3.5.3.6.1.1 Yielding
M p Fy Z 33 ≤ M y ,
=
Mn = 
M p Fy Z 33 ≤ 1.6 M y ,
=

for stems in compression, and
for stems in tension.
(AISC F9-1, F9-2, F9-3)

3.5.3.6.1.2 Lateral-Torsional Buckling
M n = M cr =

π EI y GJ
Lb

 B + 1 + B2  ,



(AISC F9-4)

where, B is taken conservatively as:
 d  Iy
.
B = ±2.3  
 Lb  J

(AISC5 F9-5)

The plus sign for B applies when the stem is in tension (M > 0) and the minus
sign applies when the stem is in compression (M < 0).

3.5.3.6.1.3 Flange Local Buckling
When the flange is under compression (i.e., when the factored moment Mr is
positive), the nominal moment capacity is taken as follows:
Mn = FcrSxc ,

(AISC F9-6)

where. Sxc is the elastic section modulus about the compression flange, and Fcr
is determined as follows:


 Fy ,

 
Fy 

,
Fcr =  Fy  1.19 − 0.50 ( b t )


E
 


 0.69E
,

2
 ( b t )

for compact sections,
for noncompact sections, and

for slender sections,

(AISC F9-1, F9-7, F9-8)
where,

Calculation of Nominal Strengths 3 - 59

Steel Frame Design AISC 360-05

b bf
=
, (for T-Shapes)
t 2t f
b bf
= ,
t tf

(for Double Angles)

and bf and tf are described in Figure 3-1.
When the flange is in tension, i.e., when the factored moment Mr is negative,
this limit state is not considered in the program.

3.5.3.6.2 Minor Axes Bending
The nominal flexural strength for T-Shapes and Double Angles bent about their
minor (2-2) axes, i.e., the axis of symmetry, is taken as the lowest value obtained according to the limit states of yielding (plastic moment) and flange local buckling.

3.5.3.6.2.1 Yielding
Mn = Mp = FyZ22 ≤ 1.6FyS22

(AISC F6-1)

where, S22 and Z22 are the section and plastic moduli about the minor axis, respectively.

3.5.3.6.2.2 Flange Local Buckling
M p ,


M n =  M p − M p − 0.7 Fy S22

F S ,
 cr 22

(

for compact flange,
 λ − λ pf 
,

 rf − λ pf 

)  λ

for noncompact flanges, and
for slender flanges,

(AISC F6-6)
where,

Fcr =
λ=

3 - 60

0.69 E
λ2

bf
2t f

(for T-Shapes)

Calculation of Nominal Strengths

(AISC 6-4)

Chapter 3 - Design using ANSI/AISC 360-05

λ=

bf
tf

(for Double Angles)

and λpf and λrf are the limiting slendernesses for compact and noncompact
flanges, respectively, as described in Table 3-5 (AISC B4.1).

3.5.3.7 Single Angle Sections
The nominal flexural strength of angle sections is conservatively calculated
based on the principal axes of bending. The nominal flexural strength about the
major principal axis is the lowest value obtained according to the limit states of
yielding (plastic moment), lateral-torsional buckling, and leg local buckling.

3.5.3.7.1 Yielding
Mn = 1.5My ,

(AISC F10-1)

where, My is the yield moment about the axis of bending.

3.5.3.7.2 Lateral-Torsional Buckling
The nominal flexure strength for bending about the major principal axis for the
limit state of lateral-torsional buckling is given as follows:


0.17 M e 
 0.92 −
 Me ,
M y 

Mn = 
My 

 0.92 − 1.17 M  M y ≤ 1.5 M y ,
e 


if M e ≤ M y , and
if M e > M y ,
(AISC F10-2, F-10-3)

where Me is the elastic lateral-torsional buckling moment defined as follows:
 0.46 Eb 2 t 2Cb
for equal-leg angles,

L

2
Me = 


 4.9 EI zCb  β2 + 0.052  Lt  + β  for unequal-leg angles.
w
 
 w

 L2
 rz 



(AISC F10-5,6)

where,
Calculation of Nominal Strengths 3 - 61

Steel Frame Design AISC 360-05

Cb = lateral-torsional buckling modification factor for nonuniform moment diagram. It is computed using equation AISC F1-1. A limit on
Cb is imposed (Cb ≤ 1.5) in the program (AISC F10).
L

= laterally unbraced length of the member. It is taken as the max(L22,
L33) in the program because L22 and L33 are not defined in the principal direction, in. (mm).

I2 = minor principal axis moment of inertia, in.4 (mm4),
rt

= radius of gyration for the minor principal axis, in. (mm),

= angle leg thickness, in. (mm). It is taken as min(tb , tf )

βw = a section property for unequal-legged angles. It is given as follows:
=
βw

(

)

1
z w 2 + z 2 dA − 2 z0
I w ∫A

(AISC Table C-F10.1)

βw is positive for short leg in compression, negative for long leg in
compression, and zero for equal-leg angles. If the long leg is in compression anywhere along the unbraced length of the member, the
negative value of β w should be used (AISC F10.2). It is conservatively taken as negative for unequal-leg angles.
z

= coordinate along the minor principal axis

w = coordinate along the major principal axis
z0 = coordinate of the shear center along the z-axis with respect to
the centroid
Iw = major principal axis moment of inertia
Iz

= minor principal axis moment of inertia.

In the preceding equation, My is taken as the yield moment about the major
principal axis of bending, considering the possibility of yielding at the heel and
both of the leg tips.

3 - 62

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

The nominal flexural strength for bending about the minor principal axis for
the limit state of lateral-torsional buckling is not needed because the limit state
of lateral-torsional buckling does not apply for minor axis bending.

3.5.3.7.3 Leg Local Buckling
The nominal flexural strength for bending about the major and minor principal
axes of single angle sections for the limit state of hg local buckling are given as
follows:


1.5Fy Sc


 b   Fy

M n  Fy Sc  2.43 − 1.72   
 t  E


 0.71E
S

2 c
 ( b t )

if compact,
if noncompact, and
if slender,

(AISC F10-7, F10-8, F10-9)
where,
Sc = elastic section modulus to the toe in compression relative to the axis
of bending
t

= thickness of the leg under consideration

= outside width of the leg under consideration.

In calculating the bending strengths for single-angles for the limit state of leg
local buckling, the capacities are calculated for both the principal axes considering the assumption that either of the two tips (toes) can be under compression. The minimum capacities are considered.

3.5.3.8 Rectangular Sections
This section applies to rectangular sections bent about either axis.
The nominal flexural strength is the lowest value obtained according to the
limit states of yielding (plastic moment) and lateral-torsional buckling.

Calculation of Nominal Strengths 3 - 63

Steel Frame Design AISC 360-05

3.5.3.8.1 Yielding
Mn = Mp = Fy Z ≤ 1.6My

(AISC F11-1)

3.5.3.8.2 Lateral-Torsional Buckling
Limit state of lateral-torsional buckling does not apply to rectangular sections
bent about their moving axis. For rectangular sections, Mn about major axis, is
given by the following:

M p ,

 
 L d  Fy 
M = Cb 1.52 − 0.274  b2 
 My ≤ M p ,
 t E
 

 Fcr S33 ≤ M p ,

e

Lb d 0.08 E
≤
,
Fy
t2

0.08 E Lb d 1.9 E
< 2 ≤
,
Fy
Fy
t

Lb d 1.9 E
>
,
Fy
t2

(AISC F11-1, F11-2, F11-3)
where, Fcr is the critical buckling stress, which is given by

Fcr =

1.9 ECb
,
Lb d
t2

(AISC F11-4)

where, t is the width of the rectangular bar parallel to axis of bending; d is the
depth of the rectangular bar; and Lb is the length unbraced against lateral displacement of the compression region or twist of the cross-section.

3.5.3.9 Circular Sections
The nominal flexural strength is the value obtained according to the limit states
of yielding (plastic moment).
Mn = Mp = Fy Z ≤ 1.6My

(AISC F11-1)

For this section, the limit state of lateral-torsional buckling need not be considered (AISC F11.2(c)).

3.5.3.10 General Sections and Section Designer Sections
For General sections and Section Designer sections, the nominal major and
minor direction bending strengths are assumed as:
3 - 64

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

Mn = My = SFy.
The program does not check any lateral-torsional buckling, flange local buckling, web local buckling, or tension flange yielding. The program assumptions
may not be conservative. The user is expected to calculate the capacity and
overwrite it.

3.5.4 Nominal Shear Strength
The nominal shear strengths are calculated for shears along the geometric axes
for all sections. For I-Shape, Box, Channel, Double Channel, T-Shape, Double
Angle, Pipe, Circular and Rectangular sections, the principal axes coincide
with their geometric axes. For Angle sections, principal axes do not coincide
with their geometric axes.
In calculating nominal strength for shear, Vn , it is assumed that there is no intermedial stiffeners used to enhance shear strength of a section (AISC G2-2).
The code allows the use of one of following methods: (a) the limit state of
shear yielding and shear buckling without using tension-field-action (AISC
G2); and (b) post buckling strength of the member or tension-field-action
(AISC G3). The program uses the first method to calculate shear strengths.
The design shear strength, φvVn , and the allowable shear strength, Vn Ω v , are
determined using the following factors.
For all sections in both the major and minor directions, except for the web of
rolled I-Shaped members with h t w ≤ 2.24 E Fy
φv = 0.9 (LRFD)

(AISC G1)

Ω v = 1.67 (LRFD)

(AISC G1)

For the web of rolled I-Shaped members with h t w ≤ 2.24 E Fy and for major direction shear only
φv = 1.0 (LRFD)

(AISC G2.1a)

Ω v = 1.50 (ASD)

(AISC G2.1a)

Calculation of Nominal Strengths 3 - 65

Steel Frame Design AISC 360-05

3.5.4.1 Shear in the Major Direction
The nominal shear strength for major direction, Vn2 , is evaluated according to
the limit states of shear yielding and shear buckling
Vn = 0.6Fy Aw Cv ,

(AISC G2-1)

where Aw is the area of the web (overall depth times the web thickness, dtw),
and Cv is the web shear coefficient. The expressions of Aw and Cv differ from
section to section, as follows.

3.5.4.1.1 I-Shapes
For all I-shaped members, Aw is taken as the overall depth of the member times
the web thickness
Aw = dtw.

(AISC G2.1(b))

For the webs of rolled I-shaped members with h t w ≤ 2.24 E Fy , Cv is taken
as 1.
Cv = 1.

(AISC G2-2)

For webs of all other I-shaped members, including both singly and doubly
symmetric and both rolled and welded sections, Cv is taken as follows:

1.0,


1.10 kv E Fy
,
Cv = 
h tw

 1.51Ek
v
,

2
 ( h t w ) Fy

h
≤ 1.10 kv E Fy ,
tw

if 1.10 kv E Fy <
if

h
≤ 1.37 kv E Fy , and
tw

h
> 1.37 kv E Fy ,
tw

(AISC G2-3, G2-4, G2-5)
where kv is the web plate bucking coefficient and it is taken as
kv = 5.

(AISC G2.1(b)(i))

In the preceding expression, for rolled shapes, h is taken as the clear distance
between flanges less the fillet or corner radii, and for built-up welded sections,
h, is taken as the clear distance between flanges (AISC G2.1(b), B4.2).
3 - 66

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

It should be observed that the φv factor, also the Ωv factor, differs for the web
of rolled I-shaped members with h t w ≤ 2.24 E Fy from the web of other Ishaped members.

3.5.4.1.2 Channel, Double Channel, and T-Shape Sections
Aw is taken as the overall depth of the member times the web thickness
Aw = dtw

for Channel sections,

(AISC G2.1(b))

Aw = 2dtw

for Double Channel sections,

(AISC G2.1(b))

Aw = dtw

for T-Shape sections.

(AISC G2.1(b))

Cv is taken as follows:

1.0,


1.10 kv E Fy
Cv = 
h tw

 1.51Ek
v

2
 ( h t w ) Fy

h
≤ 1.10 kv E Fy ,
tw

1.10 kv E Fy <

h
> 1.37 kv E Fy ,
tw

h
≤ 1.37 kv E Fy , and
tw

(AISC G2-3, G2-4, G2-5)
where,
kv = 5

for Channel and Double Channel sections

kv = 1.2 for T-Shape sections

(AISC G2.1(b)(i))
(AISC G2.1(b)(i))

and for Channel and Double Channel sections, h is taken as the clear distance
between flanges less the fillet or corner radii (AISC G2.1(b), B4.2); and for TShape sections, h is taken as the overall depth (AISC G2.1(b)).

3.5.4.1.3 Box Sections
Aw is taken as follows:
Aw = 2htw.

(AISC G5)

Cv is taken as follows:

Calculation of Nominal Strengths 3 - 67

Steel Frame Design AISC 360-05

h

if
≤ 1.10 kv E Fy ,
1.0,
tw


h
1.10 kv E Fy
Cv = 
, if 1.10 kv E Fy < ≤ 1.37 kv E Fy , and
h tw
tw

 1.51Ek
h
v
,
if
> 1.37 kv E Fy ,

2
t
 ( h t w ) Fy
w
(AISC G5, G2-3, G2-4, G2-5)

where,
kv = 5

(AISC G5)

h = d − 3tf .

(AISC G5)

Note that the design thickness of the Box section can differ by a reduction factor from its nominal thickness if the welding process is ERW (AISC B3.12).
The choice of reduction and the reduction factor C can be overwritten on a
member-by-member basis.

3.5.4.1.4 Angle Sections
Aw and Cv are taken as follows:
Aw = bt

(AISC G4)

Cv = 1.0

(AISC G4)

where b is the width of the leg resisting the shear force.

3.5.4.1.5 Double Angle Sections
Aw and Cv are taken as follows:
Aw = 2bt

(AISC G4)

Cv = 1.0

(AISC G4)

where b is the width of the leg resisting the shear force.

3.5.4.1.6 Rectangular, Circular (Round), General and SD Sections
For these sections, Aw is calculated as the effective shear area from the basic
principle of elastic shear distribution, and Cv is taken as 1 for simplicity.
3 - 68

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

3.5.4.1.7 Pipe Section
The nominal shear strength, Vn , of round HSS (i.e, Pipe sections) according to
the limit state of shear yielding and shear buckling is taken as

Vn = Fcr Ag 2

(AISC G6-1)

where,
=
Fcr

0.78 E

( D t )3 2

≤ 0.6 Fy .

(AISC G6-2b)

The code allows Fcr to be taken as the maximum of two alternate values. The
program conservatively uses one of the two expressions only. In the preceding
equations,
Ag = gross area of section based on design wall thickness
D = outside diameter
t

= design wall thickness.

The design wall thickness is equal to 0.93 times the nominal wall thickness for
ERW HSS, and equal to the nominal wall thickness for SAW HSS. However,
the choice of thickness reduction and the reduction factor can be overwritten in
the program on a member-by-member basis.

3.5.4.2 Shear in Minor Direction
The nominal shear strength for minor directions, Vn3 , is evaluated according to
the limit states of shear yielding and shear buckling as follows:
Vn = 0.6Fy Aw Cv ,

(AISC G2-1)

where, Aw is the shear area for minor direction shear, and Cv is the web shear
coefficient. The expression of Aw and Cv differs from section to section as follows.

3.5.4.2.1 I-Shapes, Channel, Double Channel, and T- Shapes
Aw is taken as the sum of flange areas.

Calculation of Nominal Strengths 3 - 69

Steel Frame Design AISC 360-05

2 b f t f

b fb t fb + b ft t ft

Aw = 2b f t f

4b f t f
b t
 f f

Doubly Symmetric I-Shapes
Singly Symmetric I-Shapes
Channels

(AISC G7)

Double Channels
T Shapes

Cv is taken as follows:
h

≤ 1.10 kv E Fy ,
if
1.0,
tw

1.10 kv E Fy
h

Cv = 
, if 1.10 kv E Fy < ≤ 1.37 kv E Fy , and
h
t
t
w
w

 1.51Ek
h
v
> 1.37 kv E Fy ,
,
if

2
tw
 ( h t w ) Fy
(AISC G7, G2-3, G2-4, G2-5)

where h t w is really meant for flange and is taken as follows,
b f

h b f
=
t w b f
b
 f

2t f

I Shapes

Channels

Double Channels

2t f

T Shapes

(AISC G7)

and kv is taken as 1.2,
kv = 1.2.

(AISC G7)

All dimensions used in the preceding equation are explained in Figure 3-1. For
Singly Symmetric I-Shapes where each flange has its own properties, the shear
capacity contribution is calculated for each flange separately based on its own
dimensions, and then the combinations are added together.

3.5.4.2.2 Box Sections, Angles, and Double Angles
The shear capacity in the minor direction, Vn3 , is calculated in exactly the same
way as for calculation of the major shear capacity, Vn2 , except that the appropriate dimensions are used (AISC G4, G5, G1).
3 - 70

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

3.5.4.2.3 Pipe Sections
The shear capacity in the minor direction, Vn3 , is exactly the same as that for
major direction (AISC G6).

3.5.4.2.4 Rectangular, Circular (Round), General and SD Sections
For these sections, Aw is calculated as the effective shear area from the basic
principle of elastic stress distribution. Cv is taken as 1 for simplicity. Then,
equation G2-1 is used to calculate the shear capacity.

3.5.5 Nominal Torsional Strength
The nominal torsion strengths are calculated for closed sections such as Boxes
and Pipes only. Torsion is ignored in design for all other section types.
The design torsional strength, φTTn, and the allowable torsional strength,
Tn ΩT , are determined using the following resistance and safety factors:
φT = 0.90 (LRFD)

(AISC H3.1)

ΩT = 1.67 (ASD)

(AISC H3.1)

The nominal torsional strength, Tn , according to the limit states of torsional
yielding and torsional buckling, is as follows:
Tn = Fcr C,

(AISC H3-1)

where C is the torsional shear constant, and Fcr is the critical buckling stress.
For round HSS (i.e., Pipe sections), C is taken conservatively as

π( D − t ) t
2
2

(AISC H3.1 Note)

Fcr is taken as,
Fcr = max(Fcr1, Fcr2) ≤ 0.6Fy ,

(AISC H3.1)

where,

Calculation of Nominal Strengths 3 - 71

Steel Frame Design AISC 360-05

Fcr1 =

Fcr 2 =

1.23E
LD
D  t 
0.60 E
D
 t 
 

, and

(AISC H3-2a)

(AISC H3-2b)

In the preceding equations,
L

= torsional unbraced length of the member, LLTB. This length is taken
as the minor direction unbraced length for flexural buckling, L22 , by
default. However, this length can be overwritten in the program.

D = outside diameter of the Pipe section
t

= design wall thickness

For regular HSS (i.e., Box sections),
=
C 2 ( b f − t w )( d − t f

){ min ( tw , t f ) } − 4.5 ( 4 − π ){ ( min ( t f , tw ) )

}

(AISC H3.1)

0.6 Fy ,


2.45 E Fy

,
Fcr = 0.6 Fy
(h t )


E
0.458π2
,
2

(h t )

if h t ≤ 2.45 E Fy ,
if 2.45 E Fy < h t ≤ 3.07 E Fy , and
if 3.07 E Fy < h t ≤ 26.0.

(AISC H3-3, H3-4, H3-5)
The variables bf , tw , d, tf , h and t used in the preceding expression have been
explained in Figure 3-1. In calculating h t , the maximum of the ratio of depth
to thickness and width to thickness are considered.
Here t is the design thickness. The design wall thickness is equal to 0.93 times
the nominal wall thickness for ERW HSS and equal to the nominal wall thick3 - 72

Calculation of Nominal Strengths

Chapter 3 - Design using ANSI/AISC 360-05

ness for SAW HSS. However, the choice of thickness reduction and the reduction factor can be overwritten in the program on a member-by-member basis.

3.6

Design of Members for Combined Forces
Previous sections of this design manual address members subject to only one
type of force, namely axial tension, axial compression, flexure or shear. This
section addresses the design of members subject to a combination of two or
more of the individual forces.
In the calculation of the demand/capacity (D/C) ratios, first, for each station
along the length of the member, the actual member force/moment components
are calculated for each design combination. Then, the corresponding capacities
are calculated. Then, the D/C ratios are calculated at each station for each
member under the influence of each of the design combinations. The controlling D/C ratio is then obtained, along with the associated station and design
combination. A D/C ratio greater than the D/C ratio limit (whose default value
is 1.0) indicates exceeding a limit state.
During the design, the effect of the presence of bolts or welds is not considered.

3.6.1 Doubly and Singly Symmetric Members Subjected to
Flexure and Axial Compression
The interaction of flexure and axial compression in all members with Doubly
Symmetric sections (I-Shapes, Double Channel, Box, Pipe, Solid Circular, Solid Rectangular) and Singly Symmetric sections (Channel, T-Shape, Double
Angle), with some exceptional cases, is given as follows:
For

Pr
≥ 0.2
Pc
Pr 8  Mr 33 Mr 22 
+ 
+
 ≤ 1.0.
Pc 9  M c 33 M c 22 

For

(AISC H1-1a)

Pr
< 0.2
Pc

Design of Members for Combined Forces 3 - 73

Steel Frame Design AISC 360-05

Pr  Mr 33 Mr 22
+
+
2 Pc  M c 33 M c 22


 ≤ 1.0,


(AISC H1-1b)

where, Pr and Pc are the required and available axial strengths; Mr and Mc are
the required and available flexural strengths; and 3 and 2 represent the strong
and weak axes, respectively.
Depending on the selected design provisions (LRFD or ASD), the aforementioned terms are defined as follows:
For design according to LRFD provisions:
Pt = required axial compressive strength using LRFD load combinations
Pc = design axial compressive strength = φcPn
Mr = required flexural strength using LRFD load combinations
Mc = design flexural strength = φbMn
φc = resistance factor for compression = 0.90
φb = resistance factor for flexure = 0.90
For design according to ASD provisions:
Pt = required axial compressive strength using ASD load combinations
Pc = allowable axial compressive strength = Pn/Ωc
Mr = required flexural strength using ASD load combinations
Mc = allowable flexural strength = Mn/Ωb
Ωc = safety factor for compression = 1.67
Ωb = safety factor for flexure = 1.67
As an exception, for Circular and Pipe sections, an SRSS (Square Root of Sum
of Squares) combination is made first of the two bending components before
adding the axial load component, instead of the single algebraic addition as
implied by the interaction equations given by AISC H1-1a and AISC H1-1b.
The resulting interaction equation is given by the following:
For

3 - 74

Pr
≥ 0.2
Pc

Design of Members for Combined Forces

Chapter 3 - Design using ANSI/AISC 360-05

2
2 

Pr 8   Mr 33   Mr 22  
+
+

 
 ≤ 1.0.
Pc 9   M c 33   M c 22  



For

Pr
< 0.2
Pc
2
2 

Pr   Mr 33   Mr 22  
+ 
 +
 ≤ 1.0.
2 Pc   M c 33   M c 22  



The philosophy behind the preceding modification is that the engineer has the
freedom to choose the principal axis. The engineer can easily choose the principal axis to match with the resultant moment so that the design is always
based on the uniaxial bending with axial force. In that case, the moment will be
the resultant (SRSS) moment from the two components. The resultant D/C ratio calculated using the preceding equations will match the calculated D/C ratio
from the pure resultant moment for the Pipe section. The reason is that Mn for
the Pipe section is independent of the K and L factors. However, for solic circular (round) sections, the resultant stress ratio calculated using the preceding
equations will not match exactly with the calculated D/C ratio from the pure
resultant moment because Mn for this section depends on the K and L factors,
which are known for only two given principal directions.
As an exception, for members with double symmetric sections in flexure and
compression with negligible minor axis bending moment, two independent
limit states, namely in-plane instability and out-of-plane buckling, also are
considered separately considering the combined approach provided in AISC
equations H1-1a and H1-1b. The minimum ratio provided by the original approach (AISC H1-1a, H1-1b) and the alternative approach described herein are
taken as the resulting D/C ratio.
a) For the limit state of in-plane instability, equations H1-1a and H1-1b are
used with Mc having a different meaning.
For

Pr
≥ 0.2
Pc

Design of Members for Combined Forces 3 - 75

Steel Frame Design AISC 360-05

Pr 8  Mr 33
M
+ 
+ r 22
Pc 9  M c 33, NoLTB M c 22

For


 ≤ 1.0.


(AISC H1-1a, H1.3a)

Pr
< 0.2
Pc
Pr  Mr 33
M
+
+ r 22

2 Pc  M c 33, NoLTB M c 22


 ≤ 1.0,


(AISC H1-1b, H1.3a)

where, all the terms in the preceding equations are the same as explained
earlier in this section, except Mc33,NoLTB is explained as follows:
For LRFD:
Mc33,NoLTB = φbMn33 = design flexural strength determined in accordance with Chapter F, except that in determining Mn33 , in this case, the
lateral torsional buckling is not considered.
For ASD:
Mn33,NoLTB = M n 33 Ωb = allowable flexural strength determined in accordance with Chapter F, except that in determining Mn33 , in this case,
the lateral torsional buckling is not considered.
In general, Mn33,NoLTB is either larger than the regular Mn33 or equal to (for
Pipe sections) the regular Mn33. The negligibility of the minor axis moment
is tested in the program by using a tolerance (0.001) multiplied by the minor direction capacity (Mn22).
b) For the limit state of out-of-plane buckling, the following interaction equation is used
2

Pr  Mr 33 
+
 ≤ 1.0
Pco  M c 33 

(AISC H1-2)

where
Pco

3 - 76

available compressive strength considering out-of-plane
bending; it is taken equal to φcPn ,

Design of Members for Combined Forces

Chapter 3 - Design using ANSI/AISC 360-05

Mc33 =

available flexural strength considering all limit states, including lateral-torsional buckling.

As an exception, any singly-symmetric I-Shape section with I yc I y beyond the
range of 0.1 ≤ I yc I y ≤ 0.9 is considered beyond the scope of the code (AISC
H.1, F13.2). Those sections are not checked by the program.
As an exception, all General sections and section created using Section Designer are treated as Doubly or Singly Symmetric sections. The equations H11a and H1-1b are use for calculation of the D/C ratios.
The program considers the left-hand side to calculate the D/C ratio. The D/C
ratio is really compared with the D/C ratio limit rather than 1. By default, the
D/C ratio limit is 0.95. This limit can be changed in the Preferences.

3.6.2 Doubly and Singly Symmetric Members Subjected to
Flexure and Axial Tension
The interaction of flexure and axial tension in all members with Doubly Symmetric sections (I, Double Channel, Box, Pipe, Solid Circular, Solid Rectangular) and Singly Symmetric sections (Channel, T-Shapes, Double Angle), with
some exceptional cases, are given as follows:
For

Pr
≥ 0.2
Pc
Pr 8  Mr 33 Mr 22 
+ 
+
 ≤ 1.0
Pc 9  M c 33 M c 22 

For

(AISC H1-2, H1-1a)

Pr
< 0.2
Pc
Pr  Mr 33 Mr 22
+
+
2 Pc  M c 33 M c 22


 ≤ 1.0,


(AISCH1-2, H1-1b)

where, Pr and Pc are the required and available axial strengths; Mr and Mc are
the required and available flexural strengths; and 3 and 2 represent the strong
and weak axes, respectively.

Design of Members for Combined Forces 3 - 77

Steel Frame Design AISC 360-05

Depending on the selected design provisions (LRFD or ASD), the aforementioned terms are defined as follows:
For design in accordance with LRFD provisions:
Pt = required axial tensile strength using LRFD load combinations
Pc = design axial tensile strength = φcPn
Mr = required flexural strength using LRFD load combinations
Mc = design flexural strength = φbMn
φt = resistance factor for tension (0.90 yielding, 0.75 rupture) (AISC D2)
φb = resistance factor for flexure = 0.90
For design in accordance with ASD provisions:
Pt = required axial compressive strength using ASD load combinations
Pc = allowable axial compressive strength = Pn/Ωc
Mr = required flexural strength using ASD load combinations
Mc = allowable flexural strength = Mn/Ωb
Ωt = safety factor for tension (1.67 yielding, 2.00 rupture) (AISC D2)
Ωb = safety factor for flexure = 1.67
As an exception, for Circular and Pipe sections, an SRSS (Square Root of Sum
of Squares) combination is made first of the two bending components before
adding the axial load component, instead of the single algebraic addition as
implied by the interaction equations given by AISC H1-1a and AISC H1-1b.
The resulting interaction equation is given by the following:
For

Pr
≥ 0.2
Pc
2
2 

Pr 8   Mr 33   Mr 22  
+

 +
 ≤ 1.0
Pc 9   M c 33   M c 22  



For

3 - 78

Pr
< 0.2
Pc

Design of Members for Combined Forces

Chapter 3 - Design using ANSI/AISC 360-05

2
2 

Pr   Mr 33   Mr 22  
+ 
+
 
 ≤ 1.0.
2 Pc   M c 33   M c 22  



As an exception, any single-symmetric I-Shape section with I yc I y beyond the
range of 0.1 ≤ I yc I y ≤ 0.9 is considered beyond the scope of the code (AISC
H.1, F13.2). These sections are not checked by the program.
As an exception, all General sections and section created using Section Designer are treated as Doubly or Singly Symmetric sections. The equations H11a and H1-1b are use for calculation of the D/C ratios.
The program considers the left-hand side to calculate the D/C ratio. The D/C
ratio is really compared with the D/C ratio limit rather than 1. By default, the
D/C ratio limit is 0.95. This limit can be changed in the Preferences.

3.6.3 Unsymmetric Members Subjected to Flexure and Axial
Force
Unlike I-Shapes, Box, Channel, Double Channel, T-Shapes, Double Angle,
Pipe, Circular, and Rectangular sections, the principal axes of unsymmetric
(unequal leg) Single Angle sections do not coincide with their geometric axes.
For Single Angle sections, the principal properties of the section are determined. The forces are resolved in the principal directions (w and z). The iteration of flexure and axial stress is calculated as follows:
f
fa
f
+ bw + bz ≤ 1.0
Fa Fbw Fbz

(AISC H2-1)

where fa and Fa are the required and available axial stresses at the point of consideration; fb and Fb are required and available bending stresses; w is the subscript related to the major principal axis bending; and z is the subscript related
to the minor principal axis bending.
For design in accordance with LRFD provisions:
fa

= required axial stress using LRFD load combinations

= design axial stress = φcFcr or φt Fy

fbw , ftz

= required flexural stress using LRFD load combinations
Design of Members for Combined Forces 3 - 79

Steel Frame Design AISC 360-05

Fbw , Ftz = design flexural stress =

φb M n
S

φc

= resistance factor for compression = 0.90

φf

= resistance factor for tension (0.9 for yielding, 0.75 for rupture)
(Section AISC D2)

φb

= resistance factor for flexure = 0.90

For design in accordance with ASD provisions:
fa

= required axial stress using ASD load combinations

= allowable axial stress = Fcr / Ωc or Fy / Ωt

fbw , fbz

= required flexural stress using ASD load combinations

Fbw , Fbz = allowable flexural stress =

Mn
Ωb S

Ωc

= safety factor for compression = 1.67

Ωf

= safety factor for tension (1.67 for yielding, 2.00 for rupture)
(Section AISC D2)

Ωb

= safety factor for flexure = 1.67

For General sections and Section Designer sections, it is assumed that the section properties are given in terms of principal directions. These two types of
sections are treated as symmetric sections for interaction purposes.

3.6.4 Members Subject to Torsion, Flexure, Shear and Axial
Force
The interaction of torsion, flexure, shear, and axial force is considered only for
Box and Pipe sections and only if the torsion is significant. Torsion is considered significant when the required torsional strength, Tr , is more than 20% of
the available torsional strength, Tc (AISC H3.2). The interaction of torsion with
other forces is ignored when
Tr ≤ 0.2Tc ,

(AICS H3.2)

and for members with Box sections, the interaction of torsion, shear, flexure
and axial force is given by

3 - 80

Design of Members for Combined Forces

Chapter 3 - Design using ANSI/AISC 360-05

Pr  Mr 33 Mr 22   Vr 3 Vr 2 Tr 
+
+
+
+  ≤ 1.0,
+
Pc  M c 33 M c 22   Vc 3 Vc 2 Tc 

(AISC H3-6)

and for members with Pipe sections, the interaction of torsion, shear, flexure,
and axial forces is given by
2
2 
2

Pr   Mr 33   Mr 22    Vr 3 Vr 2 Tr 
+ 
+
+  ≤ 1.0,
 +
 +
Pc   M c 33   M c 22    Vc 3 Vc 2 Tc 



(AISC H3-6)

where, Pr and Pc are the required and available axial strength; Mr and Mc are
required and available flexural strength; Vr and Vc are required and available
shear strength; and Tr and Tc are required and available torsional strength, respectively.
For design in accordance with LRFD provisions:
Pr = required axial strength using LRFD load combinations
Pc = design compressive/tensile strength = φcPn or φt Pn
Mr = required flexural strength using LRFD load combinations
Mc = design flexural strength = φbMn
Vr = required shear strength using LRFD load combinations
Vc = desire shear strength = φ vVn
Tr = required torsional strength using LRFD load combinations
Tc = design torsional strength = φTTn
φc = resistance factor for compression = 0.90
φt = resistance factor for tension (0.9 for yielding, 0.75 for rupture) (from AISC D2)
φb = resistance factor for flexure = 0.90
φv = resistance factor for shear = 0.90
φT = resistance factor for torsion = 0.9
For design in accordance with ASD provisions:
Pr = required axial strength using ASD load combinations
Pc = allowable compressive/tensile strength = Pn / Ωc or Pn / Ωt
Mr = required flexural strength using ASD load combinations

Design of Members for Combined Forces 3 - 81

Steel Frame Design AISC 360-05

Mc = allowable flexural strength = Mn / Ωb
Vr = required shear strength using ASD load combinations
Vc = allowable shear strength = Vn /Ωv
Tr = required torsional strength using ASD load combinations
Tc = allowable torsional strength = Tn / Ωr
Ωc = safety factor for compression = 0.90
Ωt = safety factor for tension (1.67 for yielding, 2.0 for rupture) (from AISC D2)
Ωb = safety factor for flexure = 0.90
Ωv = safety factor for shear = 0.90
Ωr = safety factor for torsion = 0.90

3 - 82

Design of Members for Combined Forces

Chapter 4
Special Seismic Provisions
(ANSI/AISC 341-05)

This chapter provides a detailed description of the algorithms related to special seismic
provisions in the design/check of structures in accordance with the "ANSI/AISC 34105―Seismic Provisions for Structural Steel Buildings Including Supplement No. 1"
(AISC 2005). The code option "AISC 360-05/IBC 2006" covers these provisions. The
same code option covers "ANS/AISC 360-05―Specifications for Structural Steel
Building" (AISC 2005a, b) as the basic code. The implementation covers load
combinations from "ASCE/SEI 7-05," which is described in the section "Design
Loading Combination" of Chapter 3. The loading based on "ASCE/SEI 7-05" has been
described in a separate document entitled "CSI Lateral Load Manual" (CSI 2007).
References are also made to IBC 2006 in this chapter.
For referring to pertinent sections of the corresponding code, a unique prefix is
assigned for each code.

 Reference to the ANSI/AISC 360-05 code carries the AISC prefix.
 Reference to the ANSI/AISC 341-05, Part I code carries the AISC SEISMIC prefix
or sometimes SEISMIC only.

 Reference to the ASCE/SEI 7-05 code carries the ASCE prefix.
 Reference to the IBC 2006 code carries the IBC prefix.
4-1

Steel Frame Design AISC 360-05/IBC 2006

4.1

Notations
Most of the notations used in this chapter have been described previously in Chapter 3.
Any additional notations used in this chapter are described herein.

4.2

S DS

Design earthquake spectral response acceleration parameter at short
period (ASCE 11.4.4)

Redundancy factor (ASCE 12.3.4)

ΩO

Overstrength factor (ASCE Table 12.2-1)

Effect of horizontal component of design seismic force, including the
effect of P (ASCE 12.4.2.1)

Effect of vertical component of design seismic force (ASCE 12.4.2.2)

Enm

Horizontal seismic load effects with overstrength factor (ASCE
12.4.3.1)

Effects of horizontal seismic forces (ASCE 12.4.2.1, 12.4.3.1, 12.8.1)

Design Preferences
The steel frame design Preference are basic assignments that apply to all of the steel
frame members. The Preferences are described in Appendix B. Tables
B-1, B-2, and B-3 list the steel frame design Preferences. The following steel frame
design Preferences are relevant to the special seismic provisions.

 Framing Type
 Notional Load Coefficient
 Seismic Design Category
 Ignore Seismic Code?
 Ignore Special Seismic Load?
 Is Doubler Plate Plug Welded?

4-2

Notations

Chapter 4 Special Seismic Provisions

4.3

Overwrites
The steel frame design Overwrites are basic assignments that apply only to those
elements to which they are assigned. The overwrites are described in Appendix C.
Table C-1 lists the steel frame design Overwrites. The following steel frame design
overwrites are relevant to the special seismic provisions.

 Frame Type
 Omega0
 Overstrength factor, Ry

4.4

Supported Framing Types
The code (ANSI/AISC 341-05) now recognizes the following types of framing systems
(AISC SEISMIC 9, 10, 11, 12, 13, 14, 15, 16, 17).
Framing Type

References

SMF (Special Moment Frame)

AISC SEISMIC 9

IMF (Intermediate Moment Frame)

AISC SEISMIC 10

OMF (Ordinary Moment Frame)

AISC SEISMIC 11

STMF (Special Truss Moment Frame)

AISC SEISMIC 12

SCBF (Special Concentrically Moment Frame)

AISC SEISMIC 13

OCBF (Ordinary Concentrically Moment Frame)

AISC SEISMIC 14

EBF (Eccentrically Moment Frame)

AISC SEISMIC 15

BRBF (Buckling Restrained Moment Frame)

AISC SEISMIC 16

SPSW (Special Plate Shear Wall)

AISC SEISMIC 17

With regard to these framing types, the program has implemented specifica-tions for
all types of framing systems, except STMF, BRBF, and SPSW. Implementing those
three types of framing requires further information about modeling.

Overwrites

4-3

Steel Frame Design AISC 360-05/IBC 2006
The program recognizes the OCBF framing in its two separate incarnations: OCBF for
regular Ordinary Concentrically Braced Frames (AISC SEISMIC 14) and OCBFI for
(base) Isolated Ordinary Concentrically Braced Frames (AISC SEISMIC 14.5).
By default, the frame type is taken as Special Moment Frame (SMF) in the program.
However, the default frame type can be changed in the Preference form for all frames
or in the Overwrites form on a member-by-member basis (Chapter 3). If a frame type
Preference is revised in an existing model, the revised frame type does not apply to
frames that have already been assigned a frame type through the Overwrites; the
revised Preference applies only to new frame members added to the model after the
Preference change and to the old frame members that were not assigned a frame type
though the Overwrites.

4.5

Applicability of the Seismic Requirements
Ideally, the special seismic provisions shall apply when the seismic response
modification factor, R, is taken as greater than 3, regardless of the seismic design
category (AISC SEISMIC 1). R is specified by the applicable building code (local
code or IBC). IBC actually refers to ASCE 7-05 for the value of R (IBC 2205.2.1).
Again, when R is taken as 3 or less, the structure is not required to satisfy these
provisions, unless specifically required by the applicable building code.
The applicable building code generally restricts buildings designed with an R factor of
3 or less to Seismic Design Category (SDC) A, B, or C; however, some systems that
have R factors less than 3 are permitted in SDC D, E, or F (IBC 2205.2, ASCE 12.2.1,
ASCE Table 12.2-1).
The program assumes that the special seismic provisions are applicable to any
structural steel structure that is assigned to SDC D, E, or F, irrespective of the value
of R, and to any structural steel structure designed with an R greater than 3 and that is
assigned to SDC A, B, or C. In addition, the program allows the user to change the
default applicability of special seismic provisions using the "Ignore Seismic Code?"
Preference item.

4-4

Applicability of the Seismic Requirements

Chapter 4 Special Seismic Provisions

4.6

Design Load Combinations
The program creates the default design load combinations based on the specification of
ASCE 7-05 code. The default load combinations are generated differently when the
LRFD (ASCE 2.3.2) and ASD (ASCE 2.4.1) provisions are chosen. The default
combinations have been described in "Design Loading Combinations" in Chapter 3.
Additional information may be found in "Design Load Combinations" in Chapter 2.
The user may change the default load combinations if the governing code is different
(AISC SEISMIC 4.1).
The program assumes that the defined earthquake load is really the strength level
earthquake, which is equivalent to θ E as defined in Section 12.4.2.1 in ASCE 7-05
code. For a regular earthquake, load is considered to have two components: horizontal,

Eh and vertical Ev , which are taken as
Eh = ρθ E ,

(ASCE 12.4.2.1)

Ev = 0.2S DS D,

(ASCE 12.4.2.2)

where, ρ is the redundancy factor as defined in Section 12.3.4 of ASCE 7-05, and the
S DS is the design earthquake spectral response acceleration parameters at short
periods, as defined in Section 11.4.4 of ASCE 7-05 code.
Effectively, the seismic load combinations for the LRFD provision become

(1.2 + 0.2S DS ) DL

± ρθ E

(ASCE 2.3.2-7, 12.4.2.3)

(1.2 + 0.2S DS ) DL

± ρΩ E + 1.0 LL

(ASCE 2.3.2-7, 12.4.2.3)

( 0.9 − 0.2S DS ) DL

± ρΩ E .

(ASCE 2.3.2-7, 12.4.2.3)

The seismic load combinations for the ASD provision become

(1.0 + 0.14S DS ) DL

± 0.7 ρΩ E

(1.0 + 0.105S DS ) DL

(ASCE 2.4.1-5, 12.4.2.3)

± 0.75 ( 0.7 ρ ) Ω E + 0.75 LL
(ASCE 2.4.1-6, 12.4.2.3)

( 0.6 − 0.14S DS ) DL

± 0.7 ρΩ E .

(ASCE 2.4.1-7, 12.4.2.3)

Design Load Combinations

4-5

Steel Frame Design AISC 360-05/IBC 2006
The program automatically considers seismic load effects, including overstrength
factors (ASCE 7-05 12.4.3), as special load combinations that are created automatically
from each load combination involving seismic loads. In that case, the horizontal
component of the force is represented by Ehm , and vertical component of the force is
represented by Ev , where,

Ehm = Ω o QE and

(ASCE 12.4.3.1)

Ev = 0.2 S DS D.

(ASCE 12.4.2.2)

Effectively, the special seismic combinations for the LRFD provision are

( 0.9 − 0.2S DS ) DL

± Ω o QE

(ASCE 2.3.2-7, 12.4.3.2)

(1.2 + 0.2S DS ) DL

± Ω o QE + 1.0LL

(ASCE 2.3.2-5, 12.4.3.2)

and for the ASD provision, the combinations are

(1.0 + 0.14S DS ) DL

± 0.7Ω oθ E

(1.0 + 0.105S DS ) DL
( 0.6 − 0.14S DS ) DL

(ASCE 2.4.1-7, 12.4.3.2)

± 0.75 ( 0.7Ω o )θ E + 0.75LL (ASCE 2.4.1-6, 12.4.3.2)
± 0.7Ω oθ E

(ASCE 2.4.1-7, 12.4.3.2)

The factor S DS is described earlier in this section. Ω 0 is the seismic force
amplification factor that is required to account for structural overstrength. The factor

Ω0 is the overstrength factor, and it should be picked up from ASCE 7-05, Table 12.21 by the user and input in the Preferences and auto-seismic load definition. The default

Ω0 is taken as 3.0 in the program. If the user defines one or more autoseismic loads, the values of Ω 0 are taken as the maximum of all the Ω 0 defined for

value of

each auto-seismic load case. Also if the user defines special seismic data that includes

Ω0 value and requests that the program include the special seismic design data,
then this Ω 0 takes precedence over the default values and those defined for the autoseismic load cases. Moreover, Ω 0 can be overwritten for each individual member. The
overwritten Ω 0 gets the highest precedence. The guideline for selecting a reasonable
value for Ω 0 can be found in ASCE 7-05, Table 12.2-1.

4-6

Design Load Combinations

Chapter 4 Special Seismic Provisions
Those combinations involving

Ω0 are internal to the program. The user does NOT

need to create additional load combinations for those load combinations. The special
circumstances for which those load combinations are additionally checked are
described later in this chapter, as appropriate. The special loading combination factors
are applied directly to the load cases. It is assumed that any required scaling (such as
may be required to scale response spectra results) has already been applied to the load
cases.
The program assumes that the seismic loads defined as the strength level load is the
program load case. Otherwise, the factors ρ , Ω0 , and S DS will be unable to scale the
load to the desired level.

4.7

Classification of Sections for Local Buckling
The sections are classified in the program as Seismically Compact, Compact,
Noncompact, Slender, and Too Slender. The sections are classified as Compact,
Noncompact, or Slender sections in accordance with Section B4 of the regular code
(AISC B4, AISC Table B4.1). The limiting width/thickness ratios, λ p , λr , and λs , that
demarcate the slenderness limits for Compact, Noncompact, Slender and Too Slender
sections were given in Table 3-5 in "Classification of Sections for Local Buckling" in
Chapter 3.
Seismically compact sections are capable of developing the full plastic strength before
local buckling occurs when the section goes through low cycle fatigue and withstands
reversal of load under seismic conditions. The width/thickness ratio ( λ ) should be less
than the limit, λ ps , for the section to be Seismically Compact. The limiting
width/thickness ratio, λ ps , for compression elements is given in Table 4-1 and is based
on

the

Seismic

code

(AISC

SEISMIC

8.2,

Table I-8-1). The Seismically Compact sections are reported as "Seismically
Compact," or sometimes as "Seismic" only for brevity in the design output.

Classification of Sections for Local Buckling

4-7

Steel Frame Design AISC 360-05/IBC 2006

Channel

Singly or Doubly Symmetric I Shapes

Table 4-1 Limiting Width-Thickness Ratios of Compression Elements for Classification Sections
Width- Limiting Width-Thickness
ThickRatios for Compression
ness
Elements
Given Ratio,
Seismically Compact
Section Description
Graphical
Case
Applicable Situation
( λ ps )
(λ )
Type
of Element
Example
No.
with Code Reference
Flexural or
uniform
compression
in flanges of
rolled and
welded
I-Shaped
sections
Flexural
compression
in beam web

b f 2t f

0.30 E Fy

Beams in SMF (SEISMIC 9)

h tw

2.45 E Fy

If Ca ≤ 0.125

Webs in
flexural
compression
or combined
flexural and
axial
compression

Flexural or
Uniform
compression
in flanges

bf t f

0.30 E Fy

Flexural
compression
in beam web

h tw

2.45 E Fy

Webs in
flexural
compression
or combined
flexural and
axial
compression

4-8

1,2

Beams in SMF (SEISMIC 9)
Beams in BRBF (SEISMIC 16)
Links in EBF (SEISMIC 15)
Columns in SMF (SEISMIC 9)
Columns in SCBF (SEISMIC 13)
Columns in BRBF (SEISMIC 16)
Braces in SCBF (SEISMIC 13)
Braced in OCBF (SEISMIC 14)

3.14

h tw

E
( 1 − 1.54Ca )
Fy

If Ca > 0.125
1.12

Beams in BRBF (SEISMIC 16)
Columns in SMF (SEISMIC 9)
Columns in SCBF (SEISMIC 13)
Columns in EBF (SEISMIC 15)
Columns in BRBF (SEISMIC 16)
Braces in SCBF (SEISMIC 13)
Braces in OCBF (SEISMIC 14)

E
E
( 2.33 − C a ) ≥ 1.49
Fy
Fy

Columns in SCBF (SEISMIC 13)
Braces in SCBF (SEISMIC 13)

Beams in SMF (SEISMIC 9)

If Ca ≤ 0.125
3.14

h tw

E
( 1 − 1.54Ca )
Fy

If Ca > 0.125
1.12

Classification of Sections for Local Buckling

E
E
( 2.33 − Ca ) ≥ 1.49
Fy
Fy

Beams in BRBF (SEISMIC 16)
Columns in SMF (SEISMIC 9)
Columns in SCBF (SEISMIC 13)
Columns in EBF (SEISMIC 15)
Columns in BRBF (SEISMIC 16)
Braces in SCBF (SEISMIC 13)
Braces in OCBF (SEISMIC 14)

Chapter 4 Special Seismic Provisions

Double Angle

T Shape

Box

Double Channel

bf t f

0.30 E Fy

Flexure
compression
in beam web

h tw

2.45 E Fy

Columns in SCBF (SEISMIC 13)
Braces in SCBF (SEISMIC 13)

Beams in SMF (SEISMIC 9)

If Ca ≤ 0.125

Webs in
flexural
compression
or combined
flexural and
axial
compression

Flexural or
axial
compression
of flanges
under major
axis bending

0.64 E Fy

Columns in SCBF (SEISMIC 13)
Braces in SCBF (SEISMIC 13)
Braces in OCBF (SEISMIC 14)

Flexural
compression
of webs under
minor axis
bending

0.64 E Fy

Columns in SCBF (SEISMIC 13)
Braces in SCBF (SEISMIC 13)
Braces in OCBF (SEISMIC 14)

Flexural or
axial
compression
in flanges

b f 2t f

0.30 E Fy

Chord of STMF (SEISMIC 12)

Compression
in stems

d tw

0.30 E Fy

Chord of STMF (SEISMIC 12)

Any type of
compression
in leg

0.30 E Fy

Chord of STMF (SEISMIC 12)

Any type of
compression
in leg

0.30 E Fy

Chord of STMF (SEISMIC 12)

3.14
h tw

E
( 1 − 1.54Ca )
Fy

If Ca > 0.125
1.12

E
E
( 2.33 − Ca ) ≥ 1.49
Fy
Fy

Beams in BRBF (SEISMIC 16)
Columns in SMF (SEISMIC 9)
Columns in SCBF (SEISMIC 13)
Columns in EBF (SEISMIC 15)
Columns in BRBF (SEISMIC 16)
Braces in SCBF (SEISMIC 13)
Braces in OCBF (SEISMIC 14)

Classification of Sections for Local Buckling

4-9

Steel Frame Design AISC 360-05/IBC 2006

0.30 E Fy

Chord of STMF (SEISMIC 12)

Any type of
compression
in any leg

0.30 E Fy

Chord of STMF (SEISMIC 12)

Pipe

Any type of
compression
in any leg

Flexural or
axial
compression

Round
Bar

―――

Rectangular

Angle

Any
compression

General
SD
Section

―――

―― ―――

0.044

E
Fy

Columns in SCBF (SEISMIC 13)
Braces in SCBF (SIESMIC 13)
Braces in OCBF (SIESMIC 14)

Assumed non-compact

2.5

―――

―― ―――

Assumed non-compact

―――

―― ―――

Assumed non-compact

Diagonal web member in STMF
(SEISMIC 12)

The table uses the dimension-related variables, such as b f , t f , t w , b, t, h, D, and
so forth. Some of those variables have been explained in the table itself. Some are
explained in Figure 3-1 and also explained in the code (AISC B4.1, B4.2, Table B4.1).
The variable Ca can be expressed as follows:

 Pu ( φb Py ) for LRFD
Ca = 
 Ω b Pa Py for ASD

(AISC SEISMIC Table I-8-1 Note K)

where,

Pa = Required compressive strength (ASD)
Pu = Required compressive strength (LRFD)

Py = Axial yield strength
4 - 10

Classification of Sections for Local Buckling

Chapter 4 Special Seismic Provisions

φb = 0.90
Ω b = 1.67
When satisfying the Special Seismic criteria, it is in general not necessary for the
design sections to be Seismically Compact (AISC SEISMIC 8.2). However, for certain
special cases, the design sections must be Seismically Compact (AISC SEISMIC 8.2b)
or Compact (AISC SEISMIC 8.2a, AISC Table B4.1) as described in the "Seismic
Requirements" section of this chapter. For a situation when the code requires the
design section to be Seismically Compact, but the section fails to satisfy the criteria,
the user must modify the section. In that case, the program issues an error message in
the output.

4.8

Special Check for Column Strength
When Pu /φc Pn for LRFD provision or Ω c Pa Pn for ASD provision in columns due
to prescribed loading combination without consideration of amplified seismic load is
greater than 0.4, the axial compressive and tensile strengths are checked in the absence
of any applied moment and shear for the amplified seismic load combinations (AISC
SEISMIC 8.3(1), 4.1).
For LRFD provisions,

( 0.9 − 0.2SDS ) DL ± Ω 0QE

(ASCE 12.4.3.2, 2.3.2-7)

( 1.2 + 0.2SDS ) DL ± Ω 0QE + 1.0 LL

(ASCE 12.4.3.2, 2.3.2-5)

For ASD provisions,

( 1.0 + 0.14SDS ) DL ± 0.7Ω 0QE

(ASCE 12.4.3.2, 2.4.1-5)

( 1.0 + 0.105SDS ) DL ± 0.7 ( 0.7Ω 0 ) QE + 0.75LL

(ASCE 12.4.3.2, 2.4.1-6)

( 0.6 − 0.14SDS ) DL ± 0.7Ω 0QE

(ASCE 12.4.3.2, 2.4.1-7)

where Ω 0 and S DS are as described in the "Design Load Combinations" section in
Chapter 3.

Special Check for Column Strength

4 - 11

Steel Frame Design AISC 360-05/IBC 2006
The preceding load combinations are used to calculate axial force only because other
forces and moments are ignored. This axial capacity check is in addition to regular
strength checks for the regularly specified load combinations (AISC SEISMIC 8.3).
Those combinations involving

Ω0 are internal to the program. The user does NOT

need to create additional load combinations for such load combinations. The special
circumstances for which these load combinations are additionally checked are
described later in this chapter, as appropriate. The special loading combination factors
are applied directly to the load cases. It is assumed that any required scaling (such as
may be required to scale response spectra results) has already been applied to the load
cases.
If the overwrite item "Ignore Special Seismic Load?" is set to yes, the preceding check
will not be performed.

4.9

Member Design
This section describes the special requirements for designing a member. The section
has been divided into subsections for each framing type.

4.9.1 Special Moment Frames (SMF)
10B

For this framing system, the following additional requirements are checked or reported
(AISC SEISMIC 9).

 When Pu /φc Pn (or Ω c Pa Pn in ASD) in columns due to prescribed loading
combinations without consideration of amplified seismic load is greater than 0.4, the
axial compressive and tensile strengths are checked in absence of any applied
moment and shear for the special seismic load combination as described previously
in the "Special Check for Column" section of this manual (AISC SEISMIC 8.3, 4.1).

 All beams and columns are required to be Seismically Compact (AISC SEISMIC
9.4a, 8.2b, Table I-8-1). The limits of the width-thickness ratio, λ ps , has been

presented in this manual in Table 4-1. If these criteria are satisfied, the section is
reported as SEISMIC as described earlier under the "Classification of Sections for

4 - 12

Member Design

Chapter 4 Special Seismic Provisions
Local Buckling" section. If these criteria are not satisfied, the program issues an
error message.

 The program checks the slenderness ratio, L r , for columns to be less than 60
(AISC SEISMC 9.7b(2)). If this criterion is not satisfied, the program issues an error
message.

 The program checks the laterally unsupported length of beams not to exceed
0.086 ( E Fy ) ry (AISC SEISMIC 9.8). If this criterion is not satisfied, the program
issues an error message.

4.9.2 Intermediate Moment Frames (IMF)
1B

For this framing system, the following additional requirements are checked and
reported (AISC SEISMIC 10).

 When Pu /φc Pn

(or Ω c Pa Pn in ASD) in columns due to prescribed loading

combinations without consideration of amplified seismic load is greater than 0.4, the
axial compressive and tensile strengths are checked in absence of any applied
moment and shear for the special seismic load combinations as described previously
in the "Special Check for Column" section of this manual (AISC SEISMIC 8.3, 4.1).

 All beams and columns are checked to be Compact (AISC SEISMIC 10.4a, 8.2a,
AISC Table B4.1). The limits of the width-thickness ratio, λ p , have been presented
in this manual in Table 3-5. If this criterion is satisfied, the section is reported as
Compact as described earlier under the "Classification of Sections for Local
Buckling" section in Chapter 3. If this criterion is not satisfied, the program issues an
error message.

 The program checks the laterally unbraced length of beams between lateral braces
not to exceed the limiting value 0.17 ( E Fy ) ry (AISC SEISMIC 10.8). If this
criterion is not satisfied, the program issues an error message.

4.9.3 Ordinary Moment Frames (OMF)
12B

For this framing system, the following additional requirement is checked and reported
(AISC SEISMIC 11).

Member Design

4 - 13

Steel Frame Design AISC 360-05/IBC 2006

 When Pu /φc Pn (or Ω c Pa Pn for ASD) in columns due to prescribed loading
combinations without consideration of amplified seismic load is greater than 0.4, the
axial compressive and tensile strengths are checked in absence of any applied
moment and shear for the special seismic load combinations as described previously
in the "Special Check for Column" section of this manual (AISC SEISMIC 8.3, 4.1).

4.9.4 Special Truss Moment Frames (STMF)
13B

No special consideration for this type of framing system is given by the program. The
user is required to check the seismic design requirements for STMF independently.

4.9.5 Special Concentrically Braced Frames (SCBF)
14B

For this framing system, the following additional requirements are checked or reported
(AISC SEISMIC 13).

 When Puφc /Pn (or Ω c Pa Pn for ASD) in columns due to prescribed loading
combinations without consideration of amplified seismic load is greater than 0.4, the
axial compressive and tensile strengths are checked in the absence of any applied
moment and shear for the special seismic load combinations as described previously
in the "Special Check for Column" section of this manual (AISC SEISMIC 8.3, 4.1).

 All column and brace members are checked to be Seismically Compact according to
Table 4-1 (AISC SEISMIC 13.2d, 8.2b, Table I-8-1). If these criteria are satisfied,
the section is reported as SEISMIC as described earlier under "Classification of
Sections for Local Buckling" in this chapter. If these criteria are not satisfied, the
program issues an error message.

 The maximum Kl r ratio of the braces is checked not to exceed 4 E Fy (AISC
SEISMC 13.2a). If this criterion is not satisfied, the program issues an error message.
The program checks the following requirements for V-type or inverted V-type SCBF
frames.

 The program checks the laterally unbraced length of beams between lateral braces
not to exceed the limiting value of L pd (AISC SEISMIC 13.4a(2)). The expression
for L pd for Box and Solid rectangular sections is given as follows:

4 - 14

Member Design

Chapter 4 Special Seismic Provisions

 0.17 + 0.10  M1
L pd =
M

 2

   E  r ≥ 0.1 E  r .
   y
F  y
   Fy 
 y
(AISC A-1-8, AISC SEISMIC 13.4a(2))

For all other sections, L pd is take as follows:

M
 E 
=
L pd  0.12 + 0.076  1     ry ,
M

 2    Fy 
(AISC A-1-7, AISC SEISMIC 13.4a(2))
where,

M1 =

Smaller moment at the end of the unbraced length of beam,

M2 =

Larger moment at the end of the unbraced length of the beam,

ry =

Radius of gyration about minor axis.

M1 M 2 is positive for reverse curvature bending and negative for single curvature
bending (AISC A1.7).
Note: Beams intersected by chevron (V or inverted-V) braces are NOT currently
checked to have a strength to support loads for the following two conditions (AISC
SEISMIC 13.4a):
(a) A beam that is intersected by braces shall be designed to support the effects of
all tributary dead and live loads from load combinations stipulated by the code,
assuming the bracings are not present.
(b) A beam that is intersected by braces and supporting earthquake load shall be
designed to resist the effects of the load combinations stipulated by the code,
except the brace forces have to be replaced by their capacities. The forces in all
braces in tension shall be assumed to be equal to Ry Fy Ag (AISC SEISMIC
13.4a(1)a). The forces in all braces in compression shall be assumed to be equal
to 0.3 Pn (AISC SEISMIC 13.4a(1)b).

Member Design

4 - 15

Steel Frame Design AISC 360-05/IBC 2006

4.9.6 Ordinary Concentrically Braced Frames (OCBF)
15B

For this framing system, the following additional requirements are checked or reported
(AISC SEISMIC 14).

 When Puφc /Pn (or Ω c Pa Pn for ASD) in columns due to prescribed loading
combinations without consideration of amplified seismic load is greater than 0.4,
the axial compressive and tensile strengths are checked in the absence of any
applied moment and shear for the special seismic load combinations as described
previously in the "Special Check for Column" section of this manual (AISC
SEISMIC 8.3, 4.1).

 All brace members are checked to be Seismically Compact according to Table 4-1
(AISC SEISMIC 14.2, 8.2b, Table I-8-1). If the criteria are satisfied, the section is
reported as SEISMIC as described earlier in "Classification of Sections for Local
Buckling" in this chapter. If this criterion is not satisfied, the program issues an
error message.

 The program checks the laterally unbraced length of beams for V or inverted V
configurations between lateral braces not to exceed the limiting value of L pd
(AISC SEISMIC 14.3(2)). The expression for L pd for Box and Solid rectangular
sections is given as follows:

 E 

 M1    E 
L pd =
 0.17 + 0.10  M 2    Fy  ry ≥ 0.1  Fy  ry .
(AISC A-1-8, AISC SEISMIC 14.3(2))
For all other sections, L pd is take as follows:

M
 E 
=
L pd  0.12 + 0.076  1   
 ry ,
M

 2    Fy 
(AISC A-1-7, AISC SEISMIC 14.3(2))
where,

4 - 16

Smaller moment at the end of the unbraced length of beam,

Larger moment at the end of the unbraced length of the beam,

Member Design

Chapter 4 Special Seismic Provisions

Radius of gyration about minor axis.

M1 M 2 is positive for reverse curvature bending and negative for single
curvature bending (AISC A1.7).

 The maximum Kl /r ratio of the braces for V or inverted-V configurations is
checked not to exceed 4.0 E Fy (AISC SEISMIC 14.2). If this criterion is not
met, an error message is reported in the output.

4.9.7 Ordinary Concentrically Braced Frames from Isolated
Structures (OCBFI)
16B

For this framing system, the following additional requirements are checked or reported
(AISC SEIAMIC 14.5).

 When Pu /φc Pn

(or Ω c Pa Pn in ASD) in columns due to prescribed loading

combinations without consideration of amplified seismic load is greater than 0.4,
the axial compressive and tensile strengths are checked in absence of any applied
moment and shear for the special seismic load combinations as described
previously in the "Special Check for Column" section of this manual (AISC
SEISMIC 8.3, 4.1).

 All braces are required to be Compact (AISC SEISMIC 14.5a, 8.2a, AISC Table
B4.1). The limits of the width-thickness ratio, λ p , have been presented in this
manual in Table 3-5. If these criteria are satisfied, the section is reported as
Compact as described previously under the "Classification of Sections for Local
Buckling" section in Chapter 3. If this criterion is not satisfied, the program issues
an error message.

 The maximum Kl /r ratio for the braces is checked not to exceed 4 E Fy
(AISC SEISMIC 14.5a). If this criterion is not met, an error message is reported in
the output.

Member Design

4 - 17

Steel Frame Design AISC 360-05/IBC 2006

4.9.8 Eccentrically Braced Frames (EBF)
17B

For this framing system, the program looks for and recognizes the eccentrically braced
frame configurations shown in Figure 4-1. The following additional requirements are
checked or reported for the beams, columns and braces associated with these
configurations (AISC SEISMIC 15).

e
2

(a)

(b)

(c)

Figure 4-1. Eccentrically Braced Frame Configurations

 When Puφc /Pn (or Ω c Pa Pn for ASD) in columns due to prescribed loading
combinations without consideration of amplified seismic load is greater than 0.4,
the axial compressive and tensile strengths are checked in absence of any applied
moment and shear for the special seismic load combinations as described
previously in the "Special Check for Column" section of this manual (AISC
SEISMIC 8.3, 4.1).

 The beams are checked to be Seismically Compact according to Table 4-1 (AISC
SEISMIC 15.2a, 8.2b, Table I-8-1). If this criterion is satisfied, the section is
reported as SEISMIC as described earlier under "Classification of Sections for
Local Buckling Section" in this chapter. If this criterion is not satisfied, the
program issues an error message.

 The shear strength for link beams is taken as follows (AISC SEISMIC 15.2b):
Vu ≤ φvVn (LRFD) or

(AISC SEISMIC 15.2b)

Va ≤ Vn Ωv (ASD),

(AISC SEISMIC 152b)

where,

4 - 18

Member Design

Chapter 4 Special Seismic Provisions

Vn = min(V pa , 2 M pa / e)

=
Vpa Vp

P 
1−  r 
 Pc 

(AISC SEISMIC 15.2b)

 P
M pa =
1.18 M p 1 − r  ,
 Pc 

(AISC SESIMIC 15-1)

(AISC SEISMIC 15-2)

Vp =
0.6 Fy (d − 2t f ) t w ,

(AISC SEISMIC 15.2b)

M p = ZFy

(AISC SEISMIC 15.2b)

φ = φv (default is 0.9)

(AISC SEISMIC 15.2b)

Ω = Ωv (default is 1.67)

(AISC SEISMIC 15.2b)

Pr = Pu (LRFD)

(AISC SEISMIC 15.2b)

Pr = Pa (ASD)

(AISC SEISMIC 15.2b)

Pc = Py (LRFD)

(AISC SEISMIC 15.2b)

Pc = Py 1.5 (ASD)

(AISC SEISMIC 15.2b)

=
Py Ag Fy .

(AISC SEISMIC 15.2b)

 If Pu > 0.15 Ag Fy (LRFD) or Pa > ( 0.15 1.5 ) Ag Fy (ASD), the link beam length,

e, is checked not to exceed the following:
– if ρ′

Aw
≥ 0.3
Ag


A  Mp 
e ≤ 1.15 − 0.5ρ′ w  1.6

Ag  
V p 


(AISC SEISMIC 15-3)

Member Design

4 - 19

Steel Frame Design AISC 360-05/IBC 2006

– if ρ′

Aw
< 0.3
Ag

 Mp 
e ≤ 1.6

V p 


(AISC SEISMIC 15-4)

where,

A=
( d − 2t f ) t w
w

(AISC SEISMIC 15.2b)

ρ′= Pr / Vr

(AISC SEISMIC 15.2b)

Vr = Vu (LRFD)

(AISC SEISMIC 15.2b)

Vr = Va (ASD)

(AISC SEISMIC 15.2b)

If the check is not satisfied, the program reports an error message.

 The link beam rotation, θ , of the individual bay relative to the rest of the beam is
calculated as the story drift ∆ times bay length ( L ) divided by the total lengths of
link beams (e) in the bay.
The link rotation, θ , is checked as follows (AISC SEISMIC 15.2c):

θ=

∆L
e

– θ ≤ 0.08 radian, where link beam clear length, e ≤ 1.6 M p Vp
– θ ≤ 0.02 radian, where link beam clear length, e ≥ 2.6 M p Vp
– θ ≤ value interpolated between 0.08 and 0.02 as the link beam clear
length varies from 1.6 M p Vp to 2.6 M p Vp .
The story drift is calculated as

∆=

4 - 20

∆ s Cd
,
I

Member Design

(ASCE 12.8-15)

Chapter 4 Special Seismic Provisions
where Cd is a System Deflection Amplification Factor and I is the system
Importance Factor.

 The beam strength outside the link is checked to be at least 1.1Ry times the beam
force corresponding to the controlling link beam shear strength (AISC SEISMIC
15.6b). The controlling link beam nominal shear strength is taken as follows:

V=
n

min(Vpa , 2 M pa /e).

(AISC SEISMIC 15.6, 15.2)

The values of Vpa and M pa are calculated following the procedure described
previously (AISC SEISMIC 15.2). The correspondence between brace force and
link beam force is obtained from the associated load cases, whichever has the
highest link beam force of interest.
For load combinations including seismic effects, a load Q1 is substituted for the
term E, where Q1 is defined as the axial forces and moments generated by at least
1.1 times the expected nominal shear strength RyVn (ASIC SEISMIC 15.6b).

 All braces are checked to be at least Compact (AISC SEISMIC 15.6a, 8.2a, AISC
Table B4.1). The limits of the width-thickness ratio, λ p , have been presented in
this manual in Table 3-5. If this criterion is satisfied, the section is reported as
Compact as described earlier under the "Classification of Sections for Local
Buckling" section in Chapter 3. If this criterion is not satisfied, the program issues
an error message.

 The brace strength is checked for 1.25 Ry times the brace forces corresponding to
the controlling link beam nominal shear strength amplified by Ry

( R V ) (AISC
y n

SEISMIC 15.6a). The controlling link beam nominal shear strengths are obtained
by the process described earlier (AISC SEISMIC 15.2b).
For load combinations including seismic effects, a load Qv1 is substituted for the
term E, where Q1 is defined as axial forces and moments generated by at least
1.25 times the expected nominal shear strength of the link RyVn (ASIC SEISMIC
15.6a).

 All column members are checked to be Seismically Compact according to Table
4-1 (AISC SEISMIC 15.8, 8.2b, Table I-8-1). If these criteria are satisfied, the
section is reported as SEISMIC as described earlier under the "Classification of
Member Design

4 - 21

Steel Frame Design AISC 360-05/IBC 2006
Sections for Local Buckling" in this chapter. If these criteria are not satisfied, the
program issues an error message.

 The column strength is checked for 1.1Ry times the column forces corresponding
to the controlling link beam nominal shear strength (AISC SEISMIC 15.8). The
controlling link beam nominal shear strength and the corresponding forces are
obtained by the process described previously.
Note: Axial forces in the beams are included in checking the beams. The user is
reminded that using a rigid diaphragm model will result in zero axial forces in the
beams. The user must disconnect some of the column lines from the diaphragm to
allow beams to carry axial loads. It is recommended that only one column line per
eccentrically braced frame be connected to the rigid diaphragm or that a flexible
diaphragm model be used.

4.9.9 Buckling Restrained Braced Frames (BRBF)
18B

No special consideration for this type of framing system is given by the program. The
user is required to check the seismic design requirements for BRBF independently.

4.9.10 Special Plate Shear Walls (SPSW)
19B

No special consideration for this type of framing system is given by the program. The
user is required to check the seismic design requirements for SPSW independently.

4.10 Joint Design
When using the SEISMIC design code, the structural joints are checked and designed
for the following.

 Check the requirement of continuity plate and determination of its area
 Check the requirement of doubler plate and determination of its thickness
 Check the ratio of beam flexural strength to column flexural strength
 Report the beam connection shear
4 - 22

Joint Design

Chapter 4 Special Seismic Provisions

 Report the brace connection force

4.10.1 Design of Continuity Plates
20B

In a plan view of a beam-column connection, a steel beam can frame into a column in
the following ways.

 The steel beam frames in a direction parallel to the column major direction, i.e.,
the beam frames into the column flange.

 The steel beam frames in a direction parallel to the column minor direction, i.e.,
the beam frames into the column web.

 The steel beam frames in a direction that is at an angle to both of the principal axes
of the column, i.e., the beam frames partially into the column web and partially
into the column flange.
To achieve a proper beam-column moment connection strength, continuity plates such
as shown in Figure 2.3 of Chapter 2 are usually placed on the column, in line with the
top and bottom flanges of the beam, to transfer the compression and tension flange
forces of the beam into the column. For connection conditions described by the first
bullet, where the beam frames into the flange of the column, such continuity plates are
not always needed. The requirement depends on the magnitude of the beam-flange
force and the properties of the column. This is the condition that the program
investigates. Columns of I Sections only are investigated. The program evaluates the
continuity plate requirements for each of the beams that frame into the column flange
(i.e., parallel to the column major direction) and reports the maximum continuity plate
area that is needed for each beam flange. The continuity plate requirements are
evaluated for moment frames (OMF, IMF, SMF) only. No check is made for braced
frames (OCBE, SCBF, EBF, BRBF).
The program first evaluates the need for continuity plates. When the required
strength Pbf exceeds the available strength φRn (LRFD) or Rn Ω (ASD), as
appropriate, a continuity plate will be required. The program checks the following limit
states.

 The column flange design strength, φ Rn , and the allowable strength, Rn Ω , for the
limit state of flange local bending is given as follows:

Joint Design

4 - 23

Steel Frame Design AISC 360-05/IBC 2006

Rn = 6.25t 2fc Fyc

if not at top story

(AISC J10-1)

Rn =(0.5)6.25t 2fc Fyc

if at top story

(AISC J10.1)

where

φ =0.9 (LRFD)
Ω =1.67 (ASD)

 The available strength of the column web against local yielding at the toe of the fillet
is given as follows:

Rn =(5.0kc + t fb ) Fyc twc

if not at top story

(AISC J10-2)

Rn =(2.5kc + t fb ) Fyc twc

if at top story

(AISC J10-3)

where

φ =1.0 (LRFD)
Ω =1.5 (ASD)

 The available strength of the column web against crippling is given as follows:

 t fb
Rn =
0.80 t 1 + 3 

 dc

2
wc

  ttw
 
  t fc

1.5





 EF t
yc fc

, if not at top story

t wc

(AISC J10-4)


 t fb
0.40 t 1 + 3 
Rn =

 dc

2
wc

  ttw
 
  t fc

1.5





 EF t
yc fc

, if at top story and t fb dc ≤ 0.2

t wc

(AISC J10-5a)

  t
 t
fb
Rn =
0.40 t 1 +  4 − 0.2   tw

  d
  t fc

2
wc

4 - 24

Joint Design

1.5





 EF t
yw fc

,

t wc


(AISC J10-5b)

Chapter 4 Special Seismic Provisions
where

φ =0.75 (LRFD)
Ω =2.0 (ASD)

 The available compressive strength of the column web against local buckling is
given as follows:

Rn =

3
24 t wc
EFyc

dc
3
12 t wc
EFyc

if not at the top story

if at the top story.

(AISC J10.8)

(AISC J10.8, J10.5)

If any of the preceding conditions are not met, the program calculates the required
continuity plate area as follows.
For LRFD:

=
Acp

− φRn )

φc Fcr

(AISC J10, J10.8, E3)

For ASD:
=
Acp

− Rn Ω )

Fcr Ωc

(AISC J10, J10.8, E3)

In the preceding expressions, φc, Ωc, and Fcr are taken as follows:
φc

= 0.90 (LFRD)

(AISC E1)

Ωc, = 1.67 (ASD)
Fcr

(AISC E1)

= Flexural buckling stress of equivalent column
related to the beam-column joint

The flexural buckling stress, Fcr , is determined as follows:

Joint Design

4 - 25

Steel Frame Design AISC 360-05/IBC 2006
Fy

Fe
0.658


Fcr =  

 0.877 Fe ,



 Fy ,


KL
E
≤ 4.71
,
r
Fy

KL
E
> 4.71
,
r
Fy

(AISC J10.8, E3)

where Fe is the elastic critical buckling stress given by

Fe =

π2 E
 KL 
 r 



(AISC E3-4)

The member properties of the equivalent column are taken as follows:

 The cross-section is comprised of two stiffeners and a strip of the web having
a width of 25twc at the interior stiffener and 12twc at the ends of the columns
(AISC J10.8).
 The effective length is taken as 0.75h, i.e., K = 0.75 and L = h = dc − 2tfc
(AISC J10.8).


KL
is calculated based on the equivalent cross-section and equivalent length
r

stated here.
In addition to satisfying the preceding limit states, it is made sure that the
equivalent section, consisting of the stiffeners and part of the web plate, is able
to resist the compressive concentrated force (AISC J8). This is similar to a column capacity check. For this condition, the program calculates the required
continuity plate area as follows:
For LRFD:
=
Acp

4 - 26

Joint Design

Pbf
φc Fcr

2
− 25t wc
,

if not at top story

Chapter 4 Special Seismic Provisions

=
Acp

Pbf
φc Fcr

2
− 12t wc
,

if at top story

(AISC J10.8, E3)

For ASD:
=
Acp

=
Acp

Pbf
Fcr Ωc
Pbf
Fcr Ωc

2
− 25t wc
,

if not at top story

2
− 12t wc
,

if at top story

(AISC J10.8, E3)

An iterative process is involved as Acp, r, and Fcr are interdependent. If Acp is
needed, iteration starts with the minimum thickness and minimum width of the
continuity plate. A maximum of three iterations is performed.
If Acp ≤ 0 , no continuity plates are required. If continuity plates are required, they
must satisfy a minimum area specification defined as follows:

 The minimum thickness of the stiffeners is taken as follows:
tcpmin = 0.5t fb

(AISC J10.8)

If the maximum thickness is more than the upper limit, the program reports an error.
Here it is assumed that the continuity plate can extend for the full width of the
column flange.

 The minimum width of the continuity plate on each side plus 1/2 the thickness of the
column web shall not be less than 1/3 of the beam flange width, or

 b fp t wc 
=
bcpmin 2 
−

2 
 3

(AISC J10.8)

 So that the minimum area is given by
Acpmin = tcpmin bcpmin .

(AISC J10.8)

Therefore, the continuity plate area provided by the program is zero or the greater of
Acp and Acpmin .

Joint Design

4 - 27

Steel Frame Design AISC 360-05/IBC 2006
In the preceding equations,

Acp = Required continuity plate area
Fyc = Yield stress of the column and continuity plate material

= Beam depth

= Column depth

= Clear distance between flanges of column less fillets for rolled shapes

= Distance between outer face of the column flange and web toe of its fillet

Mu = Factored beam moment
Pbf = Beam flange force, assumed as Mu / ( db − ttb )

Rn = Nominal strength

t fb = Beam flange thickness
t fc

= Column flange thickness

t wc = Column web thickness
φ

= Resistance factor (LRFD)

Ω

= Safety factor (ASD)

The special seismic requirements additionally checked by the program are dependent
on the type of framing used. Continuity plate requirements for seismic design are
evaluated for moment frames (OMF, IMF, SMF) only. No checks are performed for
braced frames (OCBF, SCBF, and EBF).

 For OMF, the continuity plates are checked and designed for a beam flange force,

Pbf = M pb / (db − t fb ) ,
Pbf = M pb / (db − t fb )

4 - 28

Joint Design

(AISC SEISMIC 11.5)

Chapter 4 Special Seismic Provisions

 For SMF and IMF, the continuity plates are checked and designed for a beam flange
force,

Pbf = Ry Fy b fbt fb ,

Pbf = Ry Fy b fb t fb

(AISC SEISMIC 9.5, 10.5)

Note that the code insists on designing the continuity plate to match with tested
connection (AISC SEISMIC 9.5, 10.5, 11.5).

4.10.2 Design of Doubler Plates
21B

One aspect of the design of a steel framing system is an evaluation of the shear forces
that exist in the region of the beam-column intersection known as the panel zone.
Shear stresses seldom control the design of a beam or column member. However, in a
Moment-Resisting frame, the shear stress in the beam-column joint can be critical,
especially in framing systems when the column is subjected to major direction bending
and the joint shear forces are resisted by the web of the column. In minor direction
bending, the joint shear is carried by the column flanges, in which case the shear
stresses are seldom critical, and this condition is therefore not investigated by the
program.
Shear stresses in the panel zone, due to major direction bending in the column, may
require additional plates to be welded onto the column web, depending on the loading
and the geometry of the steel beams that frame into the column, either along the
column major direction or at an angle so that the beams have components along the
column major direction. See Figure 2-3 of Chapter 2. The program investigates such
situations and reports the thickness of any required doubler plates. Only columns with I
Shapes are investigated for doubler plate requirements. Also doubler plate
requirements are evaluated for moment frames (OMF, IMF, SMF) only. No check is
made for braced frames (OCBF, SCBF, EBF).
The program calculates the required thickness of doubler plates using the following
algorithms. The shear force in the panel zone, is given by

=
Vp

∑
n =1

M bn cosθ n
− Vc .
dn − t fn

Joint Design

4 - 29

Steel Frame Design AISC 360-05/IBC 2006
The available strength of the web panel zone for the limit state of shear yielding is
determined as φ Rn (LFRD) or Rn Ω (ASD), as appropriate. Assuming that the effect
of panel zone deformation on frame stability has not been considered in analysis, the
nominal strength, Rn , is determined as follows:

Rn =
0.6 Fy d c t p ,

for Pr ≤ 0.4 Pc , and


P
Rn =
0.6 Fy d c t p 1.4 − r  , for Pr > 0.4 Pc .
Pc 


(LRFD J10-9)

(LRFD J10-10)

By using V p = φRn (LRFD) or V
=
Rn Ω (ASD), as appropriate, the required
p
column panel zone thickness t p is found as follows.
For LRFD:

tp =

Vp φ
0.6 Fy d c

Vp φ

P
0.6 Fy d c 1.4 − r 
Pc 


for Pr ≤ 0.4 Pc

, for Pr > 0.4 Pc .

For ASD:

tp =

ΩV p
0.6 Fy d c

ΩV p

P
0.6 Fy d c 1.4 − r 
Pc 


for Pr ≤ 0.4 Pc

, for Pr > 0.4 Pc

The extra thickness, or the required thickness of the doubler plate is given as follows:

t dp= t p − t w ,
where

4 - 30

Joint Design

Chapter 4 Special Seismic Provisions

= Column and doubler plate yield stress

= Required column panel zone thickness

t fn

= Flange thickness of n -th beam

tdp

= Required doubler plate thickness

t fc

= Column flange thickness

= Column web thickness

= Required panel zone shear capacity kc

= Column shear in column above

= Number of beams connecting to column

= Overall depth of n -th beam connecting to column

θn

= Angle between n -th beam and column major direction

= Overall depth of column

M bn = Factored beam moment from corresponding loading combination
Rn = Nominal shear strength of panel
Pr

= Required axial strength, Pu (LRFD) or Pa (ASD)

= Column axial yield strength, Fy A

= Py (LRFD) or 0.6 Fy (ASD)

= 0.9 (LRFD)

Ω

= 1.67 (ASD)

The largest calculated value of

tdp , calculated for any of the load combinations based

on the factored beam moments and factored column axial loads, is reported.
Joint Design

4 - 31

Steel Frame Design AISC 360-05/IBC 2006
Doubler plate requirements for seismic design are evaluated for SMF only. No further
check/design is performed for other types of frames.

 For SMF, the panel zone doubler plate requirements that are reported will develop at
least the beam moments equal to the expected plastic moment capacity of the beam

(R M ),
y

or beam moments due to specified load combinations involving seismic

load (AISC SEISMIC 9.3a). For seismic design,
given previously, except that

V p is calculated using the equation

M pb is taken as Ry Fy Z 33 .

The capacity of the panel zone in resisting this shear is taken as:

 3bcf tcf2
Vn =
0.60 Fy dc t p  1 +
 db dc t p



 , for Pu ≤ 0.75Py (AISC J10-11)


 3bcf tcf2
Vn =
0.60 Fy dc t p  1 +
 db dc t p



P
  1.9 − 1.2 r
Pc



 , for Pr > 0.75Pc


(AISC J10-12)

giving the required panel zone thickness as

t p=

V p φv
0.6 Fy d c

−

3bcf tcf2
db dc

, if Pr ≤ 0.75Pc
(AISC SEISMIC 9.3a, AISC J10-11)

=
tp

V p φv

P 
0.6 Fy d c 1.9 − 1.2 r 
Pc 


−

3bcf tcf2
db d c

if Pr > 0.75Pc .

(AISC SEISMIC 9.3a, AISC J10-12)
In the preceding expression, the term V p φv is replaced by Ω vV p if the ASD
provision is followed. The required doubler plate thickness is calculated as

tdp = t p − twc
where,

4 - 32

Joint Design

Chapter 4 Special Seismic Provisions

φ = 1.0 (LRFD)

(AISC J10.6, SEISMIC 9.3a)

Ω = 1.50 (ASD)

(AISC J10.6, SEISMIC 9.3a)

bcf = width of column flange
tcf = thickness of column flange
t p = required column web thickness
db = depth of deepest beam framing into the major direction of the
column
All other terms were explained previously.

 For SMF, the program checks the following panel zone column web thickness
requirement:

t≥
Here,

− 2t fc ) + ( db − 2t fb )
90

(AISC SEISMIC 9.3b)

t is taken as twc + tdp when the doubler plate is plug welded to prevent local

buckling. In such cases,

tdp is increased if necessary to meet this criterion. If the

doubler plate is not plug welded to the web,
checking both the plates. If
declared. If

t is taken as twc and also as tdp for

twc cannot satisfy the criteria, then a failure condition is

tdp does not satisfy this criterion, then its value is increased to meet the

criteria. If the check is not satisfied, it is noted in the output.

4.10.3 Weak Beam Strong Column Measure
2B

Only for Special Moment Frames (SMF) with seismic design category (SDC) A to F,
the code requires that the sum of column flexure strengths at a joint should be more
than the sum of beam flexure strengths (AISC SEISMIC 9.6). The column flexure
strength should reflect the presence of axial force present in the column. The beam
flexural strength should reflect potential increase in capacity for strain hardening. To
facilitate the review of the strong column weak beam criterion, the program will report
a beam-column plastic moment capacity ratio for every joint in the structure.

Joint Design

4 - 33

Steel Frame Design AISC 360-05/IBC 2006
For the major direction of any column (top end), the beam-to-column-strength ratio is
obtained as
nb

Rmaj =

∑M
n =1

∗
pbn

cos θn

M ∗pcax + M ∗pcbx

(AISC SEISMIC 9.6)

For the minor direction of any column, the beam-to-column-strength ratio is obtained
as
nb

Rmaj
=

∑M
n =1

∗
pbn

sin θn

M ∗pcay + M ∗pcby

(AISC SEISMIC 9.6)

where,

Rmaj

= Plastic moment capacity ratios, in the major directions of the
column

Rmin

= Plastic moment capacity ratios, in the minor directions of the
column

M ∗pbn

= Plastic moment capacity of n-th beam connecting to column

θn

= Angle between the n-th beam and the column major direction

M ∗pcax , y = Major and minor plastic moment capacities, reduced for axial

force effects, of column above story level
M ∗pcbx , y = Major and minor plastic moment capacities, reduced for axial

force effects, of column below story level
nb

= Number of beams connecting to the column

The plastic moment capacities of the columns are reduced for axial force effects and
are taken as

4 - 34

Joint Design

Chapter 4 Special Seismic Provisions


P 
M ∗pc Z c  Fyc − uc  (LRFD) (AISC SEISMIC 9.6)
=

Ag 

 Fyc  P 
uc
=
M ∗pc Z c 
 (ASD)
−
A
1.5

g 



(AISC SEISMIC 9.6)

The plastic moment capacities of the beams are amplified for potential increase in
capacity for strain hardening as

M ∗pb = 1.1Ry Fyb Z b f mv (LFRD)
 1.1 
=
M ∗pb 
 Ry Fyb Z b f mv , (ASD)
 1.5 

(AISC SEISMIC 9.6)

where,

Z b = Plastic modulus of beam
Zc

= Plastic modulus of column

Fyb = Yield stress of beam material
Fyc = Yield stress of column material
Puc = Axial compression force in column for given load combination
Ag = Gross area of column
f mv = The moment amplification factor. It is taken as the ratio of beam
moment at the centerline of column to the moment of the column face.
This factor takes care of the M uv (LRFD) or M av (ASD) of the code
(AISC SEISMIC 9.6).

f mv = 1 +
dc

f mv is taken as follows:

dc
where,
Lb

= Depth of column section, and

Joint Design

4 - 35

Steel Frame Design AISC 360-05/IBC 2006

= clear span length of the beam.

For the preceding calculations, the section of the column above is taken to be the same
as the section of the column below, assuming that the column splice will be located
some distance above the story level.

4.10.4 Evaluation of Beam Connection Shears
23B

For each steel beam in the structure, the program will report the maximum major
shears at each end of the beam for the design of the beam shear connections. The beam
connection shears reported are the maxima of the factored shears obtained from the
loading combinations.
For special seismic design, the beam connection shears are not taken less than the
following special values for different types of framing. The special seismic
requirements additionally checked by the program are dependent on the type of
framing used and the Seismic Design Category.

 For SMF, the beam connection shear is taken as the maximum of those from regular
load combinations and those required for the development of full plastic moment
capacity of the beam. The connection shear for the development of the full plastic
moment capacity of beam is as follows:

Vu=

CM pb

=
Va

( 0.7 )

+ VDL + VLL (LRFD),

CM pb
+ VDL + VLL (ASD),
Ln

(AISC SEISMIC 9.2a(3))

where,

4 - 36

Shear force corresponding to END I or END J or beam

=
=
=

0 if beam ends are pinned, or for cantilever beam
1 if one end of the beam is pinned
2 if no ends of the beam are pinned

M pb

Plastic moment capacity of beam = 1.1 Ry M p

Joint Design

Chapter 4 Special Seismic Provisions

Clear length of the beam

VDL

Absolute maximum of the calculated beam shears at the
corresponding beam ends from the factored dead load only

VLL

Absolute maximum of the calculated beam shears at the
corresponding beam ends from the factored live load only

 For IMF, the beam connection shear is taken as the minimum of the two values: (a)
maximum shear from the load combinations and (b) maximum shear based on beam
moment capacity of the beam (AISC SEISMIC 10.2a(2)).
The maximum shear from the load combinations is determined from all of the
regular load combinations and also from the amplified seismic load combinations
(AISC SEISMIC 10.2a(2), ASCE 14.4.3). For LRFD or ASD provisions, appropriate
load combinations are considered. The load combination for amplified seismic load
combinations are also described previously in the "Design Loading Combinations"
section.
The maximum shear based on beam moment capacity is calculated for any load
combination involving seismic load by replacing the seismic effect on shear force
with the capacity shear as follows:

Vu=

CM pb

=
Va

( 0.7 )

+ VDL + VLL (LFRD),

CM pb
Lh

+ VDL + VLL (ASD).

(AISC SEISMIC 10.2a(2))

All parameters in the preceding equation have been described previously in this
section.

 For OMF, the beam connection shear is taken as the minimum of the two values: (a)
maximum shear from the load combinations and (b) maximum shear based on beam
moment capacity of the beam (AISC SEISMIC 11.2a(4)).
The maximum shear from the load combinations is determined from all of the
regular load combinations and also from the amplified seismic load combinations
(AISC SEISMIC 11.2a(4), ASCE 14.42.3). For LRFD or ASD provisions,
appropriate load combinations are considered. The load combination for amplified

Joint Design

4 - 37

Steel Frame Design AISC 360-05/IBC 2006
seismic load combinations also are described previously in the "Design Loading
Combinations" section.
The maximum shear based on beam moment capacity is calculated for any load
combination involving seismic load by replacing the seismic effect on shear force
with the capacity shear as follows:

Vu=

CM pb

=
Va

( 0.7 )

+ VDL + VLL (LFRD),

CM pb
Lh

+ VDL + VLL (ASD).

(AISC SEISMIC 11.2a(4))

All parameters in the preceding equation have been described previously in this
section. The moment connection is assumed to be FR.

 For SCBF the beam connection shear is taken as the maximum of those from
regular load combination and those from amplified seismic load combinations.

 For OCBF and OBFI, the beam connection shear is taken as the maximum of those
from regular load combinations and those from amplified seismic load
combinations.

 For EBF, the beam connection shear is taken as the minimum of the two values:
(a) maximum shear from the load combinations and (b) maximum shear based on
link beam shear capacity (AISC SEISMIC 15.7, 11.2a(4)).
The maximum shear from the load combinations is determined from all of the
regular load combinations and also from the amplified seismic load combinations
(AISC SEISMIC 15.7, 11.2a(4), ASCE 14.2.3). For LRFD or ASD, appropriate load
combinations are considered. The load combinations for amplified seismic load
combinations also were described previously in the "Design Loading Combination"
section of this chapter.
The maximum beam connection shear based on link beam shear capacity is taken as
the beam connection shear that can be developed when the link beam yields in shear.
The load factor for the seismic component of the load in the combination is
calculated to achieve forces related to yielding of the link beam. For connection
shear determination, the forces are further amplified by 1.1 Ry (AISC SEISMIC
15.7, 11.2a(4)).
4 - 38

Joint Design

Chapter 4 Special Seismic Provisions
If the beam-to-column connection is modelled with a pin in the program by releasing
the beam end, it automatically affects the beam connection shear.

4.10.5 Evaluation of Brace Connection Forces
24B

For each steel brace in the structure, the program reports the maximum axial force at
each end of the brace for the design of the brace-to-beam connections. The brace
connection forces reported are the maxima of the factored brace axial forces obtained
from the loading combinations.
For special seismic design, the brace connection forces are not taken less than the
following special values for different types of framing. The special seismic
requirements additionally checked by the program are dependent on the type of
framing used.
Bracer axial forces for seismic designs are evaluated for braced frames (SCBF, IOBF,
OCBF, EBF) only. No special checks are performed for moment frames (OMF, IMF,
SMF).

 For SCBF, the bracing connection force is taken as the minimum of the two values
(AISC SEISMIC 13.3a):

The expected yield strength in tension of the bracing member, determined as
Ry Fy Ag (LFRD) or Ry Fy Ag 1.5 (ASD), as appropriate (AISC SEISMIC
13.3a(a)).
The maximum load effect of the amplified seismic load combination (AISC
SEISMIC 13.3a(b)).
Note that the required bracing connection force for the required compressive
strength of the brace based on limit state of buckling that is equal to 1.1 Ry Pn
(LFRD) or (1.1 1.5 ) Ry Pn (ASD), as appropriate (AISC SEISMIC 13.3c), is
always less than the corresponding value considered in case (a). So this limit
state is not considered.

Joint Design

4 - 39

Steel Frame Design AISC 360-05/IBC 2006

 For OCBF or OCBFI, the bracing connection force is taken as the minimum of the
two values (AISC SEISMIC 14.4):

a. The expected yield strength in tension of the bracing member, determined as Ry Fy Ag (LFRD) or Ry Fy Ag 1.5 (ASD), as appropriate (AISC
SEISMIC 14.4(2)).
b. The maximum load effect of the amplified seismic load combination
(AISC SEISMIC 14.4 Exception (b)).
 For EBF, the required strength of the diagonal brace connection at both ends of the
brace is taken as the maximum of the following two values: (a) the maximum
connection force from the design load combinations, and (b) the maximum brace
connection force based on the link beam shear capacity (AISC SEISMIC 15.6c, and
15.6a).
The maximum connection force from the load combinations is determined for all the
regular load combinations. The amplified seismic load combinations are not
considered.
The maximum brace connection force based on link beam shear capacity is taken as
the brace connection force that can be developed when the link beam yields in shear.
The load factor for seismic component of the load in the combination is calculate to
achieve forces related to yielding of the link beam. For connection force
determination, the forces are further amplified by 1.25 Ry (AISC SEISMIC 15.6e,
15.6a).

4 - 40

Joint Design

Chapter 5
Design Output

The program has the capacity to create design output in four major ways –
graphical display, file output, tabular display, and member specific detailed design information. The graphical display includes input and output design information for members visible in the active window; the display can be sent
directly to a printer or saved to a file. The file output includes both summary and
detail design data that can be saved in RTF, HTML and plain text formats. The
tabular display output includes both summary and detail design data that can be
displayed or saved in many formats, including Excel, Access, RTF, HTML and
plain text. The member specific detailed design information shows the details of
the calculation.
The following sections describe some of the typical graphical display, file output, tabular display output, and member specific detailed design information.
Some of the design information is very specific to the chosen steel design code.
This manual addresses "AISC 360-05/IBC 2006" design code related output
information only.

5.1

Graphical Display of Design Information
The graphical display of design output includes input and output design information for all steel frame members that are visible in the active window. The
5-1

Steel Frame Design AISC 360-05/IBC 2006

graphical output can be produced in color or in gray-scaled screen display. The
active screen display can be sent directly to the printer or saved to a file in several formats.
Design input data displayed includes the following items for the "AISC
360-05/IBC 2006" code, as shown in Figure 5-1:
 Design sections
 Design framing type
 Live load reduction factors
 Unbraced length ratios, L factors, for major and minor direction of bending,
and for lateral-torsional buckling
 Effective length factor for non-sway condition, K1 factors, for major and
minor directions of bending
 Effective length factor for sway condition, K 2 factors, for major and minor
directions of bending
 Effective length factors, K z , for lateral-torsional buckling
 Cm factors for major and minor directions of bending
 Cb factors for major and minor directions of bending
 B1 factors for major and minor directions of bending
 B2 factors for major and minor directions of bending

5-2

Graphical Display of Design Information

Chapter 5 Design Output

Figure 5-1 Choice of design input data for display on the model
in the active window

 Ω0 factors
 Yield stress, Fy
 Nominal axial capacities
 Nominal bending capacities
 Nominal shear capacities
Output design data plotted on the model includes the following items for the
"ACI 360-05/IBC 2006" code as shown in Figure 5-2:
 P-M stress ratio values with members color-coded based on the ratio
 Shear stress ratio
 Continuity plate and doubler plate thickness
 Beam/column capacity ratios
 Beam connection shear force
 Brace connection axial force

Graphical Display of Design Information

5-3

Steel Frame Design AISC 360-05/IBC 2006

Figure 5-2 Choice of design output data for display on the model
in the active window

Use the Design menu > Steel Frame Design > Display Design Info command
in SAP2000/ETABS and the Advanced > Frame Design > Steel > Display
Design Information command in CSiBridge to plot design input and output
values directly on the model. The Display Steel Design Results form shown in
Figures 5-1 and 5-2 will display. Choose the Design Output or Design Input
option. One item can be selected from the drop-down list. For example, the P-M
interaction ratios can be displayed by choosing the Design Output option and
selecting P-M Ratio Colors & Values from the drop-down list. Click the OK
button to display the longitudinal reinforcing in the active window.
The graphics can be displayed in 3D or 2D mode. The standard view transformations are available for all steel design information displays. Several buttons
on the toolbar can be used to switch between 3D and 2D views. Alternatively,
click the View menu and the Set 3D View or Set 2D View commands.
The onscreen graphical display can be sent to printer using any of the following
commands. Use the File menu > Print Graphics command in
SAP2000/ETABS and the Orb > Print > Print Graphics command in
CSiBridge to print the active window. To capture the graphical display in a file
for printing through another application, use the File menu > Capture Enhanced Metafile command in SAP2000/ETABS and the Orb > Pictures >
Metafile command in CSiBridge to create an .emf file, or use the File menu >
Capture Picture command in SAP2000/ETAB and the Orb > Pictures commands in CSiBridge to create a bitmap (.bmp) file. Create a screen capture of the
active window using the Alt+ Print Screen keyboard keys in SAP2000/ETABS

5-4

Graphical Display of Design Information

Chapter 5 Design Output

or create a screen capture of the entire window using the Ctrl + Print Screen
keyboard keys. Then use the Ctrl+V keyboard keys to paste the saved image
into Paint or other graphical program.
By default the graphical displays are in color. It may be advantageous to view or
present the display in gray-scale graphics or using a white background. Use the
Options menu > Color command in SAP2000/ETABS and the Orb > Settings
> Colors command in CSiBridge to set these options.

5.2

Tabular Display of Design Information
In addition to model definition and analysis results, the design information for
all steel frame members or for only selected members can be displayed in tabular
spreadsheet format. Currently, the program generates design summary data,
PMM design details and shear design details. The tabular spreadsheet output can
be displayed by selecting the Display menu > Show Tables command in
SAP2000/ETABS and Home > Display > Show Tables command in CSiBridge
to access the Choose Tables for Display form, an example of which is shown in
Figure 5-3. That form can be used to choose which tables or sets of tables are to
be displayed.
The names of the tables are displayed in a tree structure, which can be collapsed
or expanded by clicking on an item in the tree. Click on the small check boxes
preceding the items to select those tables for display. If a branch of the tree is
selected, all of the tables under that branch are selected. The selected set of tables can be saved as a Named Set using the Save Named Set button. This named
set can be used in the future for quick selection. If one or more frame members
are selected on the structural model before accessing the Choose Tables for
Display form, the Selection Only check box will be checked when the form
displays and, the program will display information for the selected members
only; uncheck the check box to display information for all applicable "unselected" members in the model. If the Show Unformatted check box is checked,
the numbers will be displayed unformatted, instead of being displayed using a
limited number of decimal digits. The unformatted option provides higher precision output that can then be copied into other programs.

Tabular Display of Design Information

5-5

Steel Frame Design AISC 360-05/IBC 2006

Figure 5-3 Choice of design data tables for tabular display

Use the other buttons in the form to tailor the data display. For example, click the
Select Load Patterns button to specify which load patterns are to be included in
the display of model definition data; click the Select Load Case and Modify/Show Options to specify which load cases are to be included and how
analysis results are displayed.
After selecting all of the tables for steel frame design and the display options,
click the OK button to display a form showing one of the selected design tables,
with a drop-down list in the upper right-hand corner of the form that can be used
to select other tables for display. A typical design table is shown in Figure 5-4.

5-6

Tabular Display of Design Information

Chapter 5 Design Output

Figure 5-4 A typical tabular display of design data

Use the scroll bars on the bottom and right side of the tables to scroll right and
left or up and down if portions of the data table can not be displayed in the form's
display area. The columns can be resized by clicking the left mouse button on
the separator of the headers, holding down the left mouse button and then
dragging the mouse to the left or right. Reset the column widths to their default
values by selecting the Format-Filter-Sort menu > Reset Default Column
Widths command on the form. The table can be split into two or more tables by
clicking on the small black rectangular area near the bottom-left corner of the
table, holding down the left mouse button, and then dragging the mouse button
to the left or right. Repeat this process to add more splits. Use the split and
horizontal scroll bar to put two columns side by side for easier comparison. The
splits can be removed by selecting the Format-Filter-Sort menu > Remove
Splits command on the form. Alternatively, remove the split by clicking, holding and dragging the left mouse button to merge the split key to its original location.
Select multiple consecutive columns by putting the cursor on the header, holding
down the mouse button, and then dragging the mouse button left or right. Alternatively, depress the Shift key and click the left mouse button to select a range
of columns.
Tabular Display of Design Information

5-7

Steel Frame Design AISC 360-05/IBC 2006

Each of the individual fields (columns) can be formatted. Fields with text information can be set for specific types of alignment (center, left, right) and to
specific widths. In addition to setting the alignment and column widths, fields
with numeric data can be set for the maximum number of characters, zero tolerance, number of decimal digits and so forth. The tables can be formatted, filtered and sorted using multiple criteria accessed using the Format-Filter-Sort
menu on the form. Filtering and sorting features can be useful in identifying
critical cases. After specifying the table formatting information, save it to a
format file that can be used in the future by selecting the appropriate feature
available under the Format-Filter-Sort menu.
The current table (i.e., the table in the active window) can be exported to Excel,
Access, .rtf., .html, and plain text formats. In both Excel spreadsheet and Access
database formats, the tables can have many columns, making the tables very
wide. In .rft and .html formats, the tables are split at convenient points to make a
reasonably printable document. In plain text format, the tables can be saved with
or without the splits. To export a table to Excel, for example, select the File
menu > Export Current Table > To Excel command. The program will export
the entire table to an Excel spreadsheet workbook and will automatically open
the file in MS Excel. Similarly, if the table is exported to other formats, the
default editor specific to that format will open the document, provided that the
editor is available in the computer. The table will be saved in that format only if
the relevant editor is not available. Instead of exporting or displaying the currently displayed table, the entire set of available tables can be exported and
displayed in the afore-mentioned formats by selecting the File menu and the
appropriate submenu command. With these exporting and display features, the
tables can be saved in many required formats and can be printed. Many other
features of the design tables are left for the user to discover by using the program.

5.3

Detailed Display of Member Specific Information
The program has the capability to display the design details for a specific
member. The information includes member identification, shape name, section
properties, design combination name, design combination forces, and other design input data to check the design results. The information also includes stress
ratios for P-M-M and other interactions, demand/capacity ratios from shear,

5-8

Detailed Display of Member Specific Information

Chapter 5 Design Output

nominal strengths, design factors such as K , Cm , Cb , B1 , B2 , and so forth. The
design details are displayed in a summary form and also are displayed for a
specific load combination and for a specific station of a frame member.
When the design results are displayed on the model in the active window, the
detailed design information can be accessed by right clicking on the desired
frame member to display the Steel Stress Check Information form. Alternatively, click the Design menu > Steel Frame Design > Interactive Steel
Frame Design command and then right click on the frame member. An example
of that form is shown in Figure 5-5.

Figure 5-5 A typical member specific steel stress check information summary

The Steel Stress Check Information form identifies the frame members and the
analysis and design section, and includes a display area of mostly demand/capacity ratio data and a set of buttons that access forms that provide
further details about the selected frame member. The display area reports the
load combinations, the stress check stations, the P-M-M interaction ratio along
with its axial and flexural components, and the shear stress ratios. The load
combination is reported by its name, while the station is reported by its location,

Detailed Display of Member Specific Information

5-9

Steel Frame Design AISC 360-05/IBC 2006

which is measured from the I-end of the column. The number of reported line
items in the text box is equal to the number of design combinations multiplied by
the number of stations. Only one line item is highlighted in blue when the form
first displays. That item highlights the largest demand/capacity ratio from
P-M-M, major and minor shear or any other considered interaction ratio, unless
a line item(s) has design overstress or an error. In that case, the item with the
overstress or error will be selected and highlighted. If many line items are
overstressed or have an error, the last among all such line items will be selected
and highlighted.
The stress check information is always reported for the design section. If the
member is assigned an individual section, the analysis and design section are
always the same. If the member is assigned an Auto Select Section (a list of
sections), the analysis and design section can be different, unless the design has
converged.
The Overwrites and Details buttons near the bottom of the Steel Stress Check
Information form can be used to access the Steel Frame Design Overwrites form,
and the Steel Stress Check Data form, which displays detailed information about
the selected frame element. While the latter form displays information in a
non-editable format, the Overwrites form display the overwrite data in editable
format. This allows the user to enter an interactive mode of design.
 Overwrites button. Click this button to access the Steel Frame Design
Overwrites form. Use that form to make revisions to the steel frame design
overwrites and then immediately review the new design results as a summary
using the Steel Stress Check Information form, or in detail by clicking the
Details button to access the Steel Stress Check Data form. Clicking the OK
button on the Steel Frame Design Overwrites form temporarily saves any
changes. To make the changes permanent, click the OK button on the Steel
Stress Check Information form. To disregard the changes, click the Cancel
button on the Steel Stress Check Information form. An example of an Overwrites form is shown in Figure 5-6.

5 - 10

Detailed Display of Member Specific Information

Chapter 5 Design Output

Figure 5-6 A typical member specific Steel Frame Design Overwrites form

 Details button. Click this button to access the Steel Stress Check Data form.
Use the form to review all of the design details for the highlighted item. An
example of a Steel Stress Check Data form is shown in Figure 5-7. The information includes the member ID, load combo and station identifications,
steel design sections, section properties, design combination forces, stress ratios for P-M-M and other interactions, stress ratios for shear, nominal
strengths, and design factors such as, Cm , Cb , B1 , B2 , and so forth. Values
that are not applicable are reported as N/A. Similarly, N/C and N/N indicate an
item is “Not Calculated” and “Not Needed.”

Detailed Display of Member Specific Information

5 - 11

Steel Frame Design AISC 360-05/IBC 2006

Figure 5-7 A typical Steel Stress Check Data form

Before clicking the button, highlight an item for the desired design station
and design load combination in the Steel Stress Check Information display
area by clicking on the line. The data subsequently displayed will relate to
the highlighted item. By default, the most critical line item is selected
when the form first displays, as described previously.
To increase or decrease the width of the Steel Stress Check Data form, put
the cursor near the right edge of the form, click the left mouse button, and
drag the mouse cursor towards the left or right. Similarly, the height of the
form can be increased or decreased.
The text in the form can be dragged in any direction by positioning the
cursor in the middle of the form, and then clicking the left mouse button

5 - 12

Detailed Display of Member Specific Information

Chapter 5 Design Output

and dragging the text in the desired direction. Similarly, the graphical
display of the column section can also be dragged in any direction.
Use the Units drop-down list in the upper right-hand corner of the form to
change the units used to display the data. Data displayed on the form can
be sent directly to the printer by selecting the File menu > Print command
on the form. The program allows limited page setup options using the
Print Setup Command on the File menu on the form.
The Steel Stress Check Information form also includes a Tabular Data button
that when clicked displays member specific design details in a spreadsheet type
format. The tabular display of design information has been described in the
previous section. In that case, the information displayed is specific to the selected member only. The tabular output is shown for all stations and all design
load combinations for the selected member. An example of design details table
that displays after clicking the Tabular Data button is shown in Figure 5-8.

Figure 5-8 Member specific design details in tabular format

5.4

Output of Design Information
In addition to model definition and analysis results, the design information for
all steel frame members or for selected frames only can be saved in tabular
format. Currently for AISC 360-05/IBC 2006 code, the program saves design
summary data, PMM design details, and shear design details. Save the file
output by selecting the File menu > Print Tables command in SAP2000/ETAB
Output of Design Information

5 - 13

Steel Frame Design AISC 360-05/IBC 2006

and the Orb > File > Print > Print Tables command in CSiBridge to access the
Choose Tables for Printing form. An example of that form is shown in Figure
5-9. Use the options on the form to choose which table or set of tables to save in
a file or print. This form is very similar to the Choose Tables for Display form,
which has been described earlier in this chapter in the "Tabular Display of Design Information" section.

Figure 5-9 Choice of design tables for saving in a file or printing

The name of the tables are displayed in a tree structure, which can be collapsed
or expanded by clicking on an item in the tree. Click on the small check boxes
preceding the items to select those tables for printing or saving to a file. If a
branch of the tree is selected, all of the tables under that branch are selected.
When all options for printing or saving the data to file have been specified, the
settings can be saved as a Named Set using the Save Named Set button. The
Named Set can be easily recalled in the future, reducing the need to reselect the
options and ensuring that output is consistent from one printing effort to another.
5 - 14

Output of Design Information

Chapter 5 Design Output

If one or more structural members are selected before the Choose Tables for
Printing form is accessed, the Selection Only check box will be checked, and the
program will save or print the data for the selected members only; uncheck the
check box to save or print the data for all appropriate "unselected" members.
The output can be generated in a variety of formats, including rich text format
(.rft), plain text with and without splits or page breaks (.txt), and hyperlink text
markup language (.htm) by choosing the appropriate option on the right side of
the form.
Printed output can be specified to have a landscaped orientation, in which the
width of the resulting printout on a given page is longer than the height of the
printout.
Filtering criteria can be applied if those criteria were specified using the Format-Filter-Sort menu > Format Table command when the selected data tables
were displayed using the Display menu > Show Tables command in
SAP2000/ETABS and the Home > Display > Show Tables command in
CSiBridge. The output also can be specified to include a hyperlinked contents to
facilitate accessing specific areas of the printout.
There are other buttons on the form that do not affect saving or printing design
information. For example, the Select Load Patterns button affects only saving/printing model definition data. The Select Load Cases and Modify/Show
Options buttons affect only saving/printing analysis results.
After clicking all the necessary tables for steel frame design and all necessary
options, clicking the OK button will save/print the design tables.
Although the File name > Print Tables command and the Orb > File > Print >
Print Tables command paths are dedicated for saving/printing design information, these are not the only paths to do so. Design tables can be saved in
different formats using the Display menu > Show Tables command in
SAP2000/ETABS and the Home > Display > Show Tables command in
CSiBridge.

Output of Design Information

5 - 15

Steel Frame Design AISC 360-05/IBC 2006

5.5

Error Messages and Warnings
Error messages and warnings may be displayed in the steel frame design output.
The messages are numbered. A list of error messages and warnings used in Steel
Frame Design for all the design codes is provide in Appendix F. However, all of
the messages are not applicable to the AISC 360-05/IBC 2006 Code.

5 - 16

Error Messages and Warnings

Appendix A
P-Delta Effects

Modern design provisions are based on the principle that the member forces are
calculated by a second-order elastic analysis, where the equilibrium is satisfied
on the deformed geometry of the structure. The effects of the loads acting on the
deformed geometry of the structure are known as the second-order or the P-Delta
effects.
The P-Delta effects come from two sources: global lateral translation of the
frame and the local deformation of members within the frame.
Consider the frame object shown in Figure A-1, which is extracted from a story
level of a larger structure. The overall global translation of this frame object is
indicated by ∆ . The local deformation of the member is shown as δ . The total
second order P-Delta effects on this frame object are those caused by both ∆
and δ.
The program has an option to consider P-Delta effects in the analysis. When you
consider P-Delta effects in the analysis, the program does a good job of capturing the effect due to the ∆ deformation ( P-∆ effect) shown in Figure
B-1, but it does not typically capture the effect of the δ deformation ( P-δ
effect), unless, in the model, the frame object is broken into multiple elements
over its length.

Appendix A - 1

Steel Frame Design AISC 360-05/IBC 2006

∆
Original position of frame
element shown by vertical
line

δ
Final deflected position of the
frame element that includes the
global lateral translation, ∆, and
the local deformation of the
element, δ

Position of frame element
as a result of global lateral
translation, ∆, shown by
dashed line

P
Figure A-1 P-∆ and P-δ effects

In design codes, required strengths are usually required to be determined using a
second-order analysis that considers both P-∆ and P-δ effects. Approximate
second-order analysis procedures based on amplification of responses from
first-order analysis for calculating the required flexural and axial strengths are
common in current design codes and have the following general form:
M
=
B1M nt + B2 M lt
CAP
= Pnt + B2 Plt
PCAP
where,

(AISC C2-1a)
(AISC C2-1b)

M CAP , PCAP = Required axial and flexural design capacities

Appendix A - 2

M nt , Pnt

= Required axial and flexural capacities from first-order analysis of the member assuming there is no translation of the
frame (i.e., associated with the δ deformation in Figure 2-1)

M lt , Plt

= Required axial and flexural capacities from first-order analysis of the member as a result of lateral translation of the frame

Appendix A – P-Delta Effects

only (i.e.,
Figure A-1)

associated

with

the

∆

deformation

= Unitless amplification factor multiplying M nt

= Unitless amplification factor multiplying M lt , Plt

Depending on the choice of analysis methods, which is provided by the
ANSI/AISC 360-05 code, a rigorous second order analysis or the amplification
of first order analysis results to estimate the effect of second order effects is
required. The program has the capability of performing both. In the first case, the
required strengths are determined directly from the analysis results without any
amplification factors (i.e., B1 and B2 are equal to 1). However, these amplification factors can always be overwritten by the user on a member-by-member
basis, if desired, using the overwrite option.
To properly capture the P-δ effect in a finite element analysis, each element,
especially column elements, must be broken into multiple finite elements. Although a single element per member can capture the P-δ effect to some extent, the
program considers that inadequate. For practical reasons, the software internally
divides the column elements into two members. The user must provide additional subdivisions where a column is expected to have multiple inflection
points.
In general, steel frame design requires consideration of P-Delta effects in the
analysis before the check/design is performed. Although two elements per line
object are generally adequate to capture the P-∆ effect, it is recommended to use
more than two elements per line object for the cases where both P-∆ and P-δ
effects are to be considered for a member having multiple points of inflection.
However, explicit manual breaking of the member into elements has other
consequences related to member end moments and unbraced segment end moment. It is recommended that the members be broken internally by the program.
In this way, the member is recognized as one unit, end of the members are
identified properly, and P-∆ and P-δ effects are captured better.

Appendix A - 3

Appendix B
Steel Frame Design Preferences

The Steel Frame Design Preferences are basic assignments that apply to all of
the steel frame members. Tables B-1, B-2, and B-3 list Steel Frame Design
Preferences for "AISC 360-05/IBC 2006." Default values are provided for all
preference items. Thus, it is not necessary to specify or change any of the preferences. However, at least review the default values to ensure they are acceptable. Some of the preference items also are available as member specific
overwrite items. The Overwrites are described in Appendix C. Overwritten
values take precedence over the preferences.
Table B-1: Steel Frame Design Preferences
Item

Possible Values

Default Value

Design Code

Design codes
available in the
current version

AISC360-05/
IBC 2006

Time History Design

Envelopes,
Step-by-Step

Envelopes

Description
The selected design code. Subsequent design is
based on this selected code.

Toggle for design combinations that include a time
history designed for the envelope of the time history,
or designed step-by-step for the entire time history.
If a single design combination has more than one
time history case in it, that design combination is
designed for the envelopes of the time histories,
regardless of what is specified here.

Appendix B - 1

Steel Frame Design Manual AISC 360-05/IBC 2006

Table B-1: Steel Frame Design Preferences
Item

Possible Values

Default Value

Description

Framing Type

SMF, IMF,
OMF, SCBF,
OCBF, OCBFI,
EBF

SMF

This item is used for ductility considerations in the
design, when seismic provisions are considered.

Seismic Design
Category

A, B, C, D, E, F

This item varies with the Seismic Hazard Exposure
Group and the Effective Peak Velocity Related
Acceleration.

Design Provision

ASD, LRFD

LRFD

Application provisions for calculation of
allowable/design and required strength of individual
elements. Selection of ASD will enable additional
fields for safety factor overwrites, whereas selection
of LRFD will enable additional fields for resistance
factors.

Analysis Method

7 Values

Direct Analysis
Method with
General 2nd Order
Analysis and

Indicates the method used to check/design the steel
members. The design module does not verify the
acceptability of the selected design analysis method;
the user is expected to verify acceptability. Also, the
user is expected to set the appropriate stiffness
modification factors and to supply the combinations
with appropriate notional loads.

τb

Fixed

Notional Load
Coefficient

Ignore Seismic Code?

Yes, No

Toggle to consider (No) or not consider (Yes) the
seismic part of the code in design.

Ignore Special
Seismic Load?

Yes, No

Toggle to consider (No) or not consider (Yes)
special seismic load combinations in design.

Is Doubler Plate Plug
Welded?

Yes, No

Yes

Toggle to indicate if the doubler-plate is plug welded
(Yes) or it is not plug welded (No).

HSS Welding Type

ERW, SAW

Reduce HSS
Thickness?

Yes, No

Yes

Toggle to consider if the HS (Box or Pipe) thickness
is reduced (Yes) or should not be reduced (No).

Consider
Deflection?

Yes, No

Toggle to consider the deflection limit (Yes) or to
not consider the deflection limit (No).

≥0

120

Deflection limit for dead load. Inputting 120 means
that the limit is L/120. Inputting zero means no
check will be made of this item.

DL Limit, L/

Appendix B - 2

0.002

ERW

The coefficient used to define the notional load as a
fraction of a given gravity load pattern.

Indicates the procedure used for welding the steel
members.

Appendix B Steel Frame Design Preferences

Table B-1: Steel Frame Design Preferences
Item

Possible Values

Default Value

Description

Super DL+LL Limit, L/

≥0

120

Deflection limit for superimposed dead plus live
load. Inputting 120 means that the limit is L/120.
Inputting zero means no check will be made of this
item.

Live Load Limit, L/

≥0

360

Deflection limit for superimposed live load.
Inputting 360 means that the limit is L/360.
Inputting zero means no check will be made of this
item.

Total Limit, L/

≥0

240

Deflection limit for total load. Inputting 240 means
that the limit is L/240. Inputting zero means no
check will be made of this item.

Total-Camber Limit, L/

≥0

240

Limit for net deflection. Camber is subtracted from
the total load deflection to get net deflection.
Inputting 240 means that the limit is L/240. Inputting
zero means no check will be made of this item.

Pattern Live Load
Factor

≤1.0

0.75

The live load factor for automatic generation of load
combinations involving pattern live loads and dead
loads.

D/C Ratio Limit

≤1.0

0.95

The demand/capacity ratio limit to be used for
acceptability. D/C ratios that are less than or equal to
this value are considered acceptable. The program
will select members from the auto select list with
D/C ratios less than or equal to this value.

Maximum Number of Auto
Iteration

≥1

Sets the number of iterations of the analysis-design
cycle that the program will complete automatically
assuming that the frame members have been
assigned auto select sections. This is currently only
available in ETABS.

Table B-2 Additional Steel Frame Design Preferences LRFD Provision
Item

Possible Values

Default Value

Description

Phi (Bending)

≤1.0

0.9

Resistance factor for flexure.

Phi (Compression)

≤1.0

0.9

Resistance factor for compression.

Phi (Tension-Yielding)

≤1.0

0.9

Resistance factor for yielding in tension.

Phi (Tension-Fracture)

≤1.0

0.75

Resistance factor for tension rupture.

Phi (Shear)

≤1.0

0.9

Resistance factor for shear.

Phi (Shear, Short Webbed
Rolled I-Shapes)

≤1.0

1.0

Resistance factor for shear for specific
short-webbed rolled I-Shapes.

Phi (Torsion)

≤1.0

0.9

Resistance factor for torsion.

Appendix B - 3

Steel Frame Design Manual AISC 360-05/IBC 2006

Table B-3 Additional Steel Frame Design Preferences for ASD Provision
Item

Possible Values

Default Value

Description

Omega (Bending)

≥ 1.0

1.67

Safety factor for flexure.

Omega (Compression)

≥ 1.0

1.67

Safety factor for compression.

Omega (Tension-Yielding)

≥ 1.0

1.67

Safety factor for yielding in tension.

Omega (Tension-Fracture)

≥ 1.0

2.00

Safety factor for tension rupture.

Omega (Shear)

≥ 1.0

1.67

Safety factor for shear.

Omega (Shear, Short
Webbed Rolled I-Shape)

≥ 1.0

1.50

Safety factor for shear for specific short-webbed
rolled I-Shapes.

Omega (Torsion)

≥ 1.0

1.67

Safety factor torsion.

Appendix B - 4

Appendix C
Steel Frame Design Procedure Overwrites

The structural model may contain frame elements made of several structural
materials: steel, concrete, aluminum, cold-formed steel and other materials.
The program supports separate design procedures for each material type. By
default the program determines the design procedure from the material of the
frame member.
The software allows the user to turn off or turn on design of specific members
by selecting No Design or Default from material. Refer to the program Help for
information about overwriting the design procedure.

Overwrites
The steel frame design Overwrites are basic assignments that apply only to
those elements to which they are assigned. Table C-1 lists Steel Frame Design
Overwrites for "AISC 360-05/IBC 2006." Default values are provided for all
overwrite items. Thus, it is not necessary to specify or change any of the
overwrites. However, at least review the default values to ensure they are
acceptable. When changes are made to overwrite items, the program applies the
changes only to the elements to which they are specifically assigned.
overwritten values take precedence over the preferences (Appendix B).

Appendix C - 1

Steel Frame Design AISC 360-05/IBC 2006

Table C-1 Steel Frame Design Overwrites for "AISC 360-05/IBC 2006"
Item
Current Design
Section

Fame Type

Possible Values

Default Value

Description

Any defined steel
section

Analysis section The design section for the selected frame object.
When this Overwrite is applied, any previous auto
select section assigned to the frame object is
removed.

SMF, IMF,
OMF, SCBF,
OCBF, OCBFI,
EBF

From Preferences This item is used for ductility considerations in the
design.

Omega O

≥ 1.0

Consider
Deflection?

Yes, No

Deflection Check
Type

Ratio,
Absolute,
Both

DL Limit, L/

≥0

From Preferences Deflection limit for dead load. Inputting 120 means
that the limit is L/120. Inputting zero means no
check will be made of this item.

Super DL+LL
Limit, L/

≥0

From Preferences Deflection limit for superimposed dead plus live
load. Inputting 120 means that the limit is L/120.
Inputting zero means no check will be made of this
item.

Live Load Limit, L/

≥0

From Preferences Deflection limit for superimposed live load. Inputting
360 means that the limit is L/360. Inputting zero
means no check will be made of this item.

Total Limit, L/

≥0

From Preferences Deflection limit for total load. Inputting 240 means
that the limit is L/240. Inputting zero means no check
will be made of this item.

Total-Camber Limit,
L/

≥0

From Preferences Limit for net deflection. Camber is subtracted from
the total load deflection to get net deflection.
Inputting 240 means that the limit is L/240. Inputting
zero means no check will be made of this item.

DL Limit, abs

≥0

Deflection limit for dead load. Inputting zero means
no check will be made of this item.

Super DL+LL Limit,
abs

≥0

Deflection limit for superimposed dead plus live
load. Inputting zero means no check will be made of
this item.

Live Load Limit, abs

≥0

Deflection limit for superimposed live load. Inputting
zero means no check will be made of this item.

Total Limit, abs

≥0

Deflection limit for total load. Inputting zero means
no check will be made of this item.

Appendix C - 2

Calculated

This factor is related to seismic force and ductility.

From Preferences Toggle to consider the deflection limit (Yes) or to not
consider the deflection limit (No) in design.
Both

Choose to consider deflection limit as an absolute, as
a divisor of the beam length, as both, or with no
deflection limit.

Appendix C Frame Design Overwrites

Table C-1 Steel Frame Design Overwrites for "AISC 360-05/IBC 2006"
Item

Possible Values

Default Value

Description

Total–Camber Limit,
abs

≥0

Deflection limit for net deflection. Camber is
subtracted from the total load deflection to get net
deflection. Inputting a value of 240 means that the
limit is L/240. Inputting zero means no check will be
made of this item.

Specified Camber

≥0

The specified amount of camber to be reported in the
design output and to be used in the net deflection
check.

Live Load Reduction
Factor

≥0

Calculated

The reducible live load is multiplied by this factor to
obtain the reduced live load for the frame object.
Specifying zero means the value is program
determined.

Net Area to Total
Area Ratio

≥0

1.0

The ratio of the net area at the end joint to gross
cross-sectional area of the section. This ratio affects
the design of axial tension members. Specifying zero
means the value is the program default, which is 1.

Unbraced Length
Ratio (Major)

≥0

Calculated

Unbraced length factor for buckling about the frame
object major axis; specified as a fraction of the frame
object length. This factor times the frame object
length gives the unbraced length for the object.
Specifying zero means the value is program
determined.

Unbraced Length
Ratio (Minor)

≥0

Calculated

Unbraced length factor for buckling about the frame
object minor axis; specified as a fraction of the frame
object length. This factor times the frame object
length gives the unbraced length for the object.
Specifying zero means the value is program
determined.

Unbraced Length
Ratio (LTB)

≥0

L22

Unbraced length factor for lateral-torsional buckling
for the frame object; specified as a fraction of the
frame object length. This factor times the frame
object length gives the unbraced length for the
object. Specifying zero means the value is program
determined.

Effective Length
Factor (K1 Major)

≥0

1.0

Effective length factor for buckling about the frame
object major axis; specified as a fraction of the frame
object length. This factor times the frame object
length gives the effective length for the object.
Specifying zero means the value is program
determined. For beam design, this factor is always
taken as 1, regardless of any other value specified in
the Overwrites. This factor is used for the B1 factor.

Appendix C - 3

Steel Frame Design AISC 360-05/IBC 2006

Table C-1 Steel Frame Design Overwrites for "AISC 360-05/IBC 2006"
Item

Default Value

Description

≥0

1.0

Effective length factor for buckling about the frame
object minor axis; specified as a fraction of the frame
object length. This factor times the frame object
length gives the effective length for the object.
Specifying zero means the value is program
determined. For beam design, this factor is always
taken as 1, regardless of any other value specified in
the Overwrites. This factor is used for the B1 factor.

Effective Length
Factor (K2 Major)

≥0

Calculated

Effective length factor for buckling about the frame
object major axis assuming that the frame is braced
at the joints against sidewsway; specified as a
fraction of the frame object length. This factor times
the frame object length gives the effective length for
the object. Specifying zero means the value is
program determined. For beam design, this factor is
always 1, regardless of any other values specified in
the Overwrites. The factor is used for axial
compression capacity.

Effective Length
Factor (K2 Minor)

≥0

Calculated

Effective length factor for buckling about the frame
object minor axis assuming that the frame is braced
at the joints against sidewsway; specified as a
fraction of the frame object length. This factor times
the frame object length gives the effective length for
the object. Specifying zero means the value is
program determined. For beam design, this factor is
always 1, regardless of any other values specified in
the Overwrites. The factor is used for axial
compression capacity.

Effective Length
Factor (K LTB)

≥0

K2 minor

Effective length factor for lateral-torsional buckling;
specified as a fraction of the frame object length.
This factor times the frame object length gives the
effective length for the object. Specifying zero means
the value is program determined. For beam design,
this factor is taken as 1 by default. The values should
be set by the user.

Moment Coefficient
(Cm Major)

≥0

Calculated

Unitless factor; Cm for major axis bending is used in
determining the interaction ratio. Inputting zero
means the value is program determined.

Moment Coefficient
(Cm Minor)

≥0

Calculated

Unitless factor; Cm for minor axis bending is used in
determining the interaction ratio. Inputting zero
means the value is program determined.

Bending Coefficient
(Cb)

≥0

Calculated

Unitless factor; Cb is used in determining the
interaction ratio. Inputting zero means the value is
program determined.

NonSway Moment
Factor (B1 Major)

≥0

Calculated

Unitless moment magnification factor for non-sway
major axis bending moment. Specifying zero means
the value is program determined.

NonSway Moment
Factor (B1 Minor)

≥0

Calculated

Unitless moment magnification factor for non-sway
minor axis bending moment. Specifying zero means
the value is program determined.

Effective Length
Factor (K1 Minor)

Appendix C - 4

Possible Values

Appendix C Frame Design Overwrites

Table C-1 Steel Frame Design Overwrites for "AISC 360-05/IBC 2006"
Item

Default Value

Description

≥0

1.0

Unitless moment magnification factor for sway
major-axis bending moment. Specifying zero means
the value is program determined. The program
determined value is taken as 1 because it is assumed
that P-Delta effects were specified to be included in
the analysis, and thus no further magnification is
required.

Sway Moment
Factor (B2 Minor)

≥0

1.0

HSS Welding Type

ERW, SAW

From Preferences Indicates the procedure used to check/design the steel
members.

Reduce HSS
Thickness?

Yes, No

From Preferences Toggle to consider if the HS (Box or Pipe) thickness
is reduced (Yes) or should not be reduced (No).

Yield Stress, Fy

≥0

From Material

Material yield strength used in the design/check.
Specifying zero means the value is program
determined. The program determined value is taken
from the material property assigned to the frame
object.

Overstrength
Factory, Ry

≥0

From Material

The ratio of the expected yield strength to the
minimum specified yield strength. This ratio is used
in capacity-based design for special seismic cases.
Specifying zero means the value is program
determined.

Compressive
Capacity, Pnc

≥0

Calculated

Nominal axial compressive capacity. Specifying
zero means the value is program determined.

Tensile Capacity,
Pnt

≥0

Calculated

Nominal axial tensile capacity. Specifying zero
means the value is program determined.

Major Bending
Capacity, Mn3

≥0

Calculated

Nominal bending moment capacity in major axis
bending. Specifying zero means the value is program
determined.

Minor Bending
Capacity, Mn2

≥0

Calculated

Nominal bending moment capacity in minor axis
bending. Specifying zero means the value is program
determined.

Major Shear
Capacity, Vn2

≥0

Calculated

Nominal shear capacity force for major direction
shear. Specifying zero means the value is program
determined.

Minor Shear
Capacity, Vn3

≥0

Calculated

Nominal shear capacity force for minor direction
shear. Specifying zero means the value is program
determined.

Sway Moment
Factor (B2 Major)

Possible Values

Appendix C - 5

Steel Frame Design AISC 360-05/IBC 2006

Table C-1 Steel Frame Design Overwrites for "AISC 360-05/IBC 2006"
Item
D/C Ratio Limit

Appendix C - 6

Possible Values
≥0

Default Value

Description

Calculated

The demand/capacity ratio limit to be used for
acceptability. D/C ratios that are less than or equal to
this value are considered acceptable. Specifying zero
means the value is program determined.

Appendix D
Interactive Steel Frame Design

The Interactive Steel Frame Design command is a powerful mode that allows
the user to review the design results for any steel frame design and
interactively revise the design assumptions and immediately review the revised
results.
Note that a design must have been run for the interactive design mode to be
available. With the design results displayed, right click on a frame object to
display the Steel Stress Check Information form for the member. Click on the
Overwrites button to display the Design Overwrites form, where the member
section or other design parameters may be changed. Clicking OK on this form
results in an immediate updating of the results displayed on the Steel Stress
Check Information form.

Appendix D - 1

Appendix E
Analysis Sections vs. Design Sections

Analysis sections are those section properties used to analyze the model when
an analysis is run (refer to the program Help for information about running an
analysis). The design section is whatever section is used in the steel frame
design. It is possible for the last used analysis section and the current design
section to be different. For example, an analysis may be run using a W18X35
beam, and then in the design, it may be found that a W16X31 beam worked. In
that case, the last used analysis section is the W18X35 and the current design
section is the W16X31. Before the design process is complete, verify that the
last used analysis section and the current design section are the same. Refer to
the program Help for information about completing this task.
The program keeps track of the analysis section and the design section
separately. Note the following about analysis and design sections:


Assigning a frame section property assigns the section as both the analysis
section and the design section.



Running an analysis always sets the analysis section to be the same as the
current design section.



Assigning an Auto Select section list to a frame object initially sets the
analysis and design section to be the section in the list with the median
weight.
Appendix E - 1

Steel Frame Design AISC 360-05/IBC 2006



Unlocking a model deletes the design results, but it does not delete or
change the design section.



Altering the Design Combinations in any way deletes the design results,
but does not delete or change the design section.



Altering any of the steel frame design preferences deletes the design
results, but does not delete or change the design section.

Appendix E - 2

Appendix F
Error and Warning Messages

This appendix provides all the possible error message that can be offered by the
Steel Frame Design model of the program. Some of these messages are relevant
to the "AISC 360-05/IBC 2006" design code. Others are relevant to the other
design codes supported by the program. However, the entire list is presented
here for completeness.
Error
Number

Description

kl/r > 200

l/r > 300

P > Pe

P > 0.85Py

P . 075Py

1/r > 720/sqrt(Fy)

1 > 96ry

Appendix F - 1

Steel Frame Design AISC 360-05/IBC 2006

Error
Number

Appendix F - 2

Description

h/tw > 380/sqrt(Fy)

Section is slender

Section is Class 4

Section is not plastic

Pu > Pe(B1 is undefined)

Cf > Ce (U1 is undefined)

bf/2tf > 52/sqrt(Fy)

1u > 76bf/sqrt(Fy)

fe > Fe

l/r > 180

l/r > 250

1/r > 120

l/r > 140

Pu > Phi * Pe (Delta b is undefined)

N/C (Not Calculated)

Internal Program Error

Section is too slender

1/r > 1000/sqrt (Fy)

Story drift too high

bf/2tf > 52/sqrt (Fy)

Appendix I Error and Warning Messages

Error
Number

Description

b/t > 100/Sqrt (Fy)

d/t > 1300/Fy

b/t > 52/sqrt (Fy)

Section is not compact

tz < (dz+wz)/90

b/t > 100/Sqrt (Fy)

1/r > 2500/Fy

Fy > 50 ksi

Link is too long

Section is not seismically compact

Phi factor less than or equal to zero

1o/f > 150*Sqrt (235/fy)

1o/f > 300*Sqrt (235/fy)

1o/f > 200*Sqrt (235/fy)

1o/f > 150*Sqrt (235/fy)

1o/f > 120*Sqrt (235/fy)

1o/f > 100*Sqrt (235/fy)

1o/f > 90*Sqrt (235/fy)

1o/f > 80*Sqrt (235/fy)

1o/f > 60*Sqrt (235/fy)

Appendix F - 3

Steel Frame Design AISC 360-05/IBC 2006

Error
Number

Appendix F - 4

Description

tz < (dz+wz)/70

1/r >60

1/r > 0.086*ry*E/Fy

kl/r > 4.23*Sqr(e/Ey

Link Rotaion is too high

Phib factor less than or equal to zero

Lambda_y > 120*sqrt(235/fy): Phib is no longer correct

0.8 N/Ney > .0 : Column is unstable

Beam/Column capacity ratio exceeds limit

Capacity ratio exceeds limit

Section is seismically slender &

tz < (dz+wz)/90

Beam/column capacity ratio exceed limit

Section is slender

Section is unknown

Section is not supported for design

Section is too slender – Effective area negative

Section is too slender – Effective Moment of inertia negative

Section is too slender – D/t high

kl/r > 150

Appendix I Error and Warning Messages

Error
Number

Description

kl/r > 250

l/r > 500

Unequal legs

Nue * N > Ncr

1/r > 5.87*ry*E/Fy

kl/r > 180 (IS 3.7, Table 3.1)

kl/r > 250 (IS 3.7, Table 3.1)

l/r > 400 (IS 3.7, Table 3.1)

Signa_ac, cal > 0.6*fcc (Excessive amplification) (IS 7.1.1)

Appendix F - 5

Bibliography

AISC, 2005a. ANSI/AISC 360-05: An American National Standard – Specification for Structural Steel Building, American Institute of Steel Construction. One East Wacker Drive, Suite 700, Chicago, Illinois, 60601.
March 9.
AISC, 2005b. Commentary on the Specification for Structural Steel Buildings,
American Institute of Steel Construction. One East Wacker Drive, Suite
700, Chicago, Illinois, 60601. March 9.
AISC, 2005c. Seismic Provisions for Structural Steel Buildings, Including
Supplemental No. 1. American Institute of Steel Construction. One East
Wacker Drive, Suite 700, Chicago, Illinois, 60601. March 9. Supplement,
November 16.
ASCE, 2005. SEI/ASCE 7-05. Minimum Design Loads for Buildings and Other
Structures. ASCE Standard, Including Supplement No. 1. American Society of Civil Engineers.
Boresi, A. P., 1985. Advanced Mechanics of Materials, John Wiley & Sons Inc.
ISBN 0-471-88392-1.
CSI, 2007. CSI Lateral Load Manual. Computers and Structures, Inc., 1995
University Avenue, Berkeley, California, 94704.

Bibliography - 1

Steel Frame Design AISC 360-05/IBC 2006

IBC, 2006. International Building Code, International Code Council, 4051 West
Flossmoor Road, Country Club Hills, Illinois, 60478. January.
Popov, E. P., 1990. Engineering Mechanics of Solids, Prentice-Hall Inc. ISBN
0-13279258-3.
White, D.L. and J. F. Hajjar, 1991. “Application of Second-Order Elastic
Analysis in LRFD: Research to Practice,” Engineering Journal, ACI, Vol.
28, No. 4, pp. 133–148.
Wilson, E. L., 1965, "Structural Analysis of Axisymmetric Solids," AIAA
Journal 3, 2269–2274.

Bibliography - 2

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Randy Corson
Create Date                     : 2016:10:23 16:25:05-07:00
Modify Date                     : 2016:10:25 15:56:05-07:00
Title                           : 
Has XFA                         : No
Tagged PDF                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2016:10:25 15:56:05-07:00
Creator Tool                    : Acrobat PDFMaker 11 for Word
Format                          : application/pdf
Creator                         : Randy Corson
Document ID                     : uuid:432a3a74-e559-4acd-be1c-46a2db08d987
Instance ID                     : uuid:075ce279-7101-4ec5-9e4e-a998a507461c
Producer                        : Adobe PDF Library 11.0
Page Layout                     : SinglePage
Page Count                      : 197

EXIF Metadata provided by EXIF.tools

SFD AISC 360 05

Navigation menu

Versions of this User Manual:

Views

Navigation