Manual SG2100 New1 HH 2100 SG

User Manual: HH-2100

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

DiSEqC 1.2 Motorized H
-H Motor
H-H

SG-2100

Compatible with DiSEqC 1.2 Receivers
Adjustable Hardware Limit Switches
Indicating LED for Easy Trouble Shooting
Manual Button for Easy Installation
Compact, Powerful and Quiet
For Dish up to 1.2 M
Goto X Function

ADJUST THE HARDWARE LIMITS if necessary
The factory preset hardware limits are from 70°East to 70°West. If smaller azimuth range is required,
adjust the hardware limits as the following:
1. Always drive the motor to 0 position before
adjust the hardware limits.
2. Disassemble the Mounting Tube.
3. Loose the screw on the Limit Slider. Please
don’t loose the screw thoroughly; otherwise,
the Slider might drop into the motor.
4. Adjust the Limit Slider to the wanted angle
( 20~70°for East or West ) .
5. Tighten the screws again.
6. Assemble the Mounting Tube onto the motor.
Drive the motor East and West via the Manual
Button or receiver to make sure the new
hardware limits are well set.

ASSEMBLE THE MOTOR
1.
2.
3.

Assemble the H-H Motor as the following diagram.
Make sure the mounting pole is exactly vertical before
installation.
Fix the H-H Motor onto the mounting pole.

INSTALLING THE MOTOR
I. Traditional Installation:
1. Aiming TRUE SOUTH.
Attaching the Antenna Dish to the Motor. Make sure it is at the center of the mounting tube.
Rotate the motor together with the antenna toward TRUE SOUTH. You can find the TRUE
SOUTH via the magnetic variation table and a compass that indicates the MAGNETIC
SOUTH.

-1-

2. Setting Elevation Angle of the Motor.
Adjust the motor elevation angle via the Inclinometer or the Elevation / Latitude scale on
both sides of the Motor.
3. Setting Angle of the Dish.
??Attach the Dish onto the motor. The centerline on the tube of the motor can help to
mount the Dish on the center. Find the Declination Angle by the attached ANGLE
TABLE.
??Set the Declination Angle by the scale on the antenna dish. The reading on the Dish
scale should be:
40° - DECLINATION ANGLE

Setting Elevation Angle

Setting Declination Angle

4. Drive the antenna east and west via the manual button on the bottom of the Motor or via
Receiver to check if the reception arc is correct. If not, adjust the direction, elevation, and
declination angle to find the best reception.
p.s. Please connect the Motor to the receiver via coaxial cable to get the power. The Green LED
will light on if the power from the receiver is on.
II. Quick Installation (A receiver with Goto X Function is recommended):
1. Set Elevation Angle of the motor:
According to the Latitude of your location, set the elevation angle of the motor. There
is also a Latitude scale on the other side of the motor.
2. Mount the Dish:
Mount the Dish onto the motor. The centerline on the tube of the motor can help to
mount the Dish on the center.
Find the Declination Angle by the attached ANGLE TABLE.
Set the Declination Angle by the scale on the antenna dish. The reading on the Dish
scale should be:
40° - DECLINATION ANGLE Please refer to the drawing on Page 2.
-2-

3. Drive the motor to the position for a favorite satellite:
According to your Longitude and the position of the wanted satellite, drive the motor
to the right position. For example, a user in Paris (Longitude is 2.5°E) wants to aim the
Hot Bird (13°E). Just drive the motor to 10.5°E(=13-2.5) via the manual button.
If the receiver has Goto X function, just input the longitude and wanted satellite, the
receiver can calculate and drive the motor to right angle automatically.
4. Aim the Satellite:
Move the whole unit around the pole to find the strongest signal from the wanted
satellite.
Tighten everything and the installation is finished. It will take about only 10 minutes.

CABLE CONNECTION
H-H Mount

LNB
To
LNB

Adjustable
Hardware
Limits

To
Receiver

Coaxial Cable

TV
Coaxial Cable

Indicating LED

DiSEqC 1.2 Receiver

Reset
Key

Manual Button

Connect the Motor via the coaxial cable (RG -6/U is recommended) as the following diagram.

MANUAL BUTTON
Drive the Motor East / West via only one Manual Button on the bottom of the Motor
1. West: Press once and keep pressing.
2. East: Press twice within 0.5 second and then keep pressing.
3. West Fine-tune: Press Once and release immediately for one step West.
4. East Fine-tune: Press Twice and then release the button for one step East.

INDICATING LED
The LED on the bottom of the Motor can show the following information

Color
Green
Orange
Orange

Status
On
Blink
On

Indication
Power On; Standby Mode
Receiving DiSEqC 1.2 Commands / Reset Mode
Error Message: Over Current / Reach Hardware Limits …
-3-

HARDWARE RESET
1. Make sure the power from the receiver is turn -on. The indicating LED lights on.
2. Drive the motor to 0° via the manual button.
3. Probe the RESET button behind the bottom of the motor via a thin rod for 2 seconds. The LED
blinks in Orange Color. The reset process is OK while the LED is green. The preset Satelli te
Table will be re-install and the current position will be set as 0°. Please cut off the power for the
motor first before any operation.

DiSEqC 1.2 OPERATION
The Motor is designed for DiSEqC 1.2 Receiver.

The commands on the receivers might be

different, but similar. Please refer to the manual of the receiver.
1. Go East / West: Drive the dish to East / West.
2. Fine Tune East / West: Drive the dish East / West for one step.
3. Store nn: Store Satellites Position nn (01~60).
4. Goto nn: Drive Motor to Satellite Position nn (01~60).
5. East / West Limits: Set software East / West limits.
6. Limit Off: Disable the software limits.
7. Goto 0°: Drive the Motor to 0° as a reference point.
8. Re-synchronize / Shift:
a) Drive the motor to a position by Goto command. For example, P03.
b) Drive the motor East / West to a better position.
c) Send Re-synchronize commands to the motor. The P03 will be shifted to the new position.
All the other Satellite positions are also changed.
d) If step a) is skipped, the P01 will be shifted to the new position.
P02

P03

P01

P02
P03

Stored Positions

9. Goto X Function:
e) This function only works with receivers which have goto x function.
f) It can drive the motor to exact x.x° East or West in relative to the 0 position of the motor.
( For example, 15.2° East on the bottom of the motor.)
g) Just input the longitude, some receivers can drive the antenna to focus on the right
Satellites automatically

-4-

TROUBLESHOOTING
Symptoms
The Manual Button doesn’t work
The Manual Button can only drive
the motor toward West

The Motor doesn’t work

The Motor stops at a certain
position and can’t go further.

The Motor runs discontinuously

The Motor runs sometimes fast
and sometimes slowly.

All satellite positions are not
correct.

Check points
1. Make sure the power of receiver is on and the indication
LED on the bottom of the motor lights on.
2. Check every devices between receiver and motor.
For East movement: Press the manual button twice within 1
second or shorter.
1. Make sure all cables and power are well connected. The
LED on the bottom lights on.
2. Make sure the motor is not blocked by the software limits.
Try to use the manual button, which is only limited by
hardware limits.
3. Check if the receiver supports DiSEqC 1.2 and if the
DiSEqC 1.2 system has been enabled.
1. Disable the software limits and drive the motor again.
2. Check if it’s stopped by the hardware limit sliders.
3. Make sure the Motor or antenna is not interfered with any
other item.
1. Make sure the antenna is not too heavy or too large. The
maximum size is 1.2 m.
2. Check if the cable quality is good enough. Try to use a
better RG-6/U cable.
3. Check if the output power of the receiver is less than
350mA.
The speed of the Motor is according to the output voltage (13
/18V) of the receiver.
Vertical=13V=slow
Horizontal=18V=fast
1. Goto One satellite position via receiver. Wait for about 30
seconds until the motor stops.
2. Drive the antenna East or West until the reception of this
satellite is clear.
3. Use “Re-calculate” Function to correct position via receiver.
Or
Use Goto 0 position Function to go to 0 degree as a reference
point.

The Motor runs but stops
somehow immediately

This could be caused by a loosen magnet on the rear end of the
DC motor inside. Please contact your vendor for repair.

The Motor doesn’t make any
movement, but clicks from inside
of the motor can be heard

1. Check if the dish is too heavy. The maximum size of the
antenna is 1.2 m.
2. The DC motor inside is broken. Please contact your vendor
for repair.

-5-

ELEVATION AND DECLINATION ANGLE TABLE

Your Site

Elevation

Declination

Your Site

Elevation

Declination

Latitude

Angle

Latitude

Angle

0.000

5.510

0.178

5.641

0.355

5.770

0.533

5.897

0.710

5.966

0.887

6.142

1.063

6.260

1.239

6.376

1.415

6.489

1.589

6.600

1.763

6.708

1.936

6.813

2.108

6.799

2.279

7.015

2.449

7.112

2.618

7.205

2.786

7.296

2.952

7.385

3.117

7.470

3.280

7.552

3.442

7.632

3.603

7.782

3.761

7.792

3.918

8.047

4.073

8.162

4.226

8.265

4.377

8.357

4.526

8.437

4.674

8.505

4.819

8.562

4.961

8.608

5.102

8.643

5.241

8.666

5.377

8.678

-6-

SPECIFICATION
Protocol
Compatible Receiver
Antenna Size
Speed
Azimuth Angle
Elevation Angle
Tube for Antenna
Diameter of Stand-mast
Input Voltage
Output Voltage
Power Consumption
Satellite Positions
Goto 0 Position Function
Recalculation Function
Goto X Function
Manual Button
Indicating LED
Limit Protection

:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:

Positioning Sensor
Weight
Dimension

:
:
:

DiSEqC

DiSEqC 1.2
DiSEqC 1.2 Receiver
120 cm Max.
1.9°/ sec (at 13V); 2.5°/ sec (at 18V)
75°East ~ 75°West (150°Max.) Adjustable
10~75°
Ø 55 x 160L mm
Ø 35~65 mm
13 / 18Vdc
13 / 18Vdc (according to input)
50 mA (Standby) / 200mA (Normal) / 350mA (Max.)
60 positions
Yes ( Go to 0°)
Yes
Yes
Yes (East /West)
Yes (2 Colors)
1. Adjustable Hardware Limits
2. Programmable Software Limit
3. Current Limit
High Resolution Hall Effect Sensor
3.1 Kg (Net) / 3.5 Kg (Gross)
345 x 168 x 110 mm3 (Gross)

is a trademark of EUTELSAT

BUILT-IN SAT. TABLE
No.

Satellite

Position

No.

Satellite

13°E

Hispasat

19.2°E

Telstar 11

Position
30°W

Hot Bird

Astra

Eutelsat W2

16°E

Kopernicus

Eutelsat W1

10°E

Arabsat 2A / 3A

Eutelsat W3

7°E

Astra 2

28.2°E

Sirius 2/3

5°E

EuroBird

28.5°E

Thor 2/3

0.8°W

Arabsat 2B

30.5°E

Intelsat 707

1°W

Turksat 1B

31.3°E

Telecom 2C

5°W

Turksat 1C

42°E

Telecom 2D

8°W

Intelsat 601

34.5°W

Intelsat 705

18°W

Pas 3R

43°W

NSS 803

21.5°W

Amos

4°W

Intelsat 605

27.5°W

Nilesat

7°W

-7-

37.5°W
23.5°E
26°E

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2003:03:06 18:30:13Z
Modify Date                     : 2004:09:11 12:09:36-04:00
Page Count                      : 8
Has XFA                         : No
Creation Date                   : 2003:03:06 18:30:13Z
Author                          : Jeremy
Producer                        : Acrobat PDFWriter 4.0Windows NT ª©
Mod Date                        : 2004:02:26 21:22:14-05:00
Metadata Date                   : 2004:02:26 21:22:14-05:00
Title                           : Manual SG2100 New1.PDF
Creator                         : Jeremy

EXIF Metadata provided by EXIF.tools

Manual SG2100 New1 HH 2100 SG

Navigation menu

Versions of this User Manual:

Views

Navigation