SPEEDFIT TEE Instructions
User Manual:
Open the PDF directly: View PDF 
.
Page Count: 3
™
The w
orld’s best-selling electric floor heating brand
WARMUP INC.
USA: us@warmup.com
Tel.: 1-888-927-6333
www.warmup.com
CANADA: ca@warmup.com
Tel.: 1-888-592-7687
www.warmup.ca
SPEEDFIT-TEE
INSTALLATION INSTRUCTIONS ™
The w
orld’s best-selling electric floor heating brand
SPEEDFIT-TEE
INSTALLATION INSTRUCTIONS
DESCRIPTION
The WARMUP Low-Profile Speedfit Tee Kit is suitable for use with
Warmup NAMSR self-regulating cable.
APPLICATION
The Speedfit-Tee is used to create a “T” connection with 3 self-
regulating cables. This application is found on tracing runs for
water lines as well as a replacement for downspout runs in roof
and gutter applications. These connection kits must be installed
according to NAMSR guidelines and minimum installation
temperatures.
APPROVALS KIT CONTENT
Item Qty Description
A 1 Main Box
B 3 Pressure Seal End
C 3 Grommets
D 2 Gaskets for Main Box
E 2 Cover for Main Box
F 1 Label
The components are electrical devices. They must be installed
correctly to ensure proper operation and to prevent shock or fire.
Carefully follow all of the installation instructions and read these
important warnings.
• To minimize the danger of fire from sustained electrical arcing
if the heating cable is damaged or improperly installed, and
to comply with the requirements of the national electrical
codes, ground-fault equipment protection must be used on
each heating cable branch circuit. Arcing may not be stopped by
conventional circuit protection.
• Bus wires will short if they contact each other. Keep bus
wire separated.
• Keep ends of heating cable and kit components dry before and
during installation.
• The black heating cable core is conductive and can short. It must
be properly insulated and kept dry.
• Component approvals and performance are based on the use
of specified parts only. Do not substituted parts or use
vinyl electrical tape.
• Leave these installation instructions with the user for future
reference.
• The heating cable should not be embedded in the thermal
insulation.
• The cable should not be twisted during installation.
• De-energize all power circuits before installation or servicing.
• The conductive layer of this heating cable device must be
connected to a suitable grounding/earthing terminal.
Caution:
Charring or burning the heat-shrinkable tubes in this kit will produce
fumes that may cause eye,shin, nose and throat irritation.
WARNING
™
The w
orld’s best-selling electric floor heating brand
WARMUP INC.
USA: us@warmup.com
Tel.: 1-888-927-6333
www.warmup.com
CANADA: ca@warmup.com
Tel.: 1-888-592-7687
www.warmup.ca
™
The w
orld’s best-selling electric floor heating brand
SPEEDFIT-TEE
INSTALLATION INSTRUCTIONS
Outer jacket
Copper Braid
Outer jacket
Insulation
PTC Cores
Bus wires
Cable with outer jacket for dry and wet conditions
INSTALLATION INSTRUCTIONS
1- Leave extra wire for connections
and mishaps.
2- Insert the Pressure Seal End first
and then the grommet for each
cable.
3-
• Do not cut the braiding.
• Strip the outer jacket.
• Slightly bend the cable where
you made the cut to strip it.
•
•
•
•
•
•
4-
• Push the braid back to create a
bump.
• Then use a screwdriver or
similar to create an opening and
slide the inner cable out of the
braided ground mesh.
• Do not cut the ground braid.
5- Now expose the inner core
cables and carbon matrix by
carefully removing the inner jacket.
Do not cut the conductor cables.
6- Twist the ground braid clean
for future connection to screw
connector.
7- Separate bus wires from the solid
carbon center and peel them off.
8- Clear about 3-4” of the inner wires
from the carbon matrix, then cut off
the excess matrix in between. You
should be left with a twisted ground
braid, and two inner conductor
cables about 3-4” long.
™
The w
orld’s best-selling electric floor heating brand
WARMUP INC.
USA: us@warmup.com
Tel.: 1-888-927-6333
www.warmup.com
CANADA: ca@warmup.com
Tel.: 1-888-592-7687
www.warmup.ca
SPEEDFIT-TEE
INSTALLATION INSTRUCTIONS ™
The w
orld’s best-selling electric floor heating brand
SPEEDFIT-TEE
INSTALLATION INSTRUCTIONS
10-
• Install wire number 3 in the
main box.
• Install the grommet into the
hole of the main box.
• Push pressure seal end and then
tight crews back into the main
box.
11-
• Loosen the screw number 3.
• Install wire number 3 on its
base.
• Tighten the screw back into
position.
• Cut all extra wire and braid.
12-
• Install the wires number 1&2 in
the main box.
• Install the grommet into the
hole of the main box.
• Push pressure seal end and then
tight crews back into the main
box.
13-
• Loosen the screws number 1&2.
• Install wire number 1&2 on their
base.
• Tighten the screw back into
position.
• Cut all extra wire and braid.
14-
• Install the 2 gaskets and the 2
covers onto the main box.
• Tighten the screw back into
position
15-
• Affix the Low-Profile Tee
Connection and side wires to the
pipe using tape.
• Affix insulation.
• Install label on the of the
insulation protector.
• Give instructions to the owner/
user.
9-
• Using the glass cloth tape, put the ponytail brain against the inner jacket and do a minimum of 3 loops around
the inner jacket.
• Separate from the cable and loop a minimum of two times around the braid.
• Install the grommet to the edge of the loop tape. Do not install grommet over the tape.
