SPEEDFIT TEE Instructions
User Manual:
Open the PDF directly: View PDF 
.
Page Count: 3
| Download | |
| Open PDF In Browser | View PDF |
The world’s best-selling electric floor heating brand ™ SPEEDFIT-TEE INSTALLATION INSTRUCTIONS DESCRIPTION The WARMUP Low-Profile Speedfit Tee Kit is suitable for use with Warmup NAMSR self-regulating cable. APPLICATION The Speedfit-Tee is used to create a “T” connection with 3 selfregulating cables. This application is found on tracing runs for water lines as well as a replacement for downspout runs in roof and gutter applications. These connection kits must be installed according to NAMSR guidelines and minimum installation temperatures. APPROVALS KIT CONTENT Item Qty Description A 1 Main Box B C D E F 3 3 2 2 1 Pressure Seal End Grommets Gaskets for Main Box Cover for Main Box Label WARNING The components are electrical devices. They must be installed correctly to ensure proper operation and to prevent shock or fire. Carefully follow all of the installation instructions and read these important warnings. • To minimize the danger of fire from sustained electrical arcing if the heating cable is damaged or improperly installed, and to comply with the requirements of the national electrical codes, ground-fault equipment protection must be used on each heating cable branch circuit. Arcing may not be stopped by conventional circuit protection. • Bus wires will short if they contact each other. Keep bus wire separated. • Keep ends of heating cable and kit components dry before and during installation. • The black heating cable core is conductive and can short. It must be properly insulated and kept dry. WARMUP INC. USA: us@warmup.com Tel.: 1-888-927-6333 www.warmup.com • • • • • • Component approvals and performance are based on the use of specified parts only. Do not substituted parts or use vinyl electrical tape. Leave these installation instructions with the user for future reference. The heating cable should not be embedded in the thermal insulation. The cable should not be twisted during installation. De-energize all power circuits before installation or servicing. The conductive layer of this heating cable device must be connected to a suitable grounding/earthing terminal. Caution: Charring or burning the heat-shrinkable tubes in this kit will produce fumes that may cause eye,shin, nose and throat irritation. CANADA: ca@warmup.com Tel.: 1-888-592-7687 www.warmup.ca The world’s best-selling electric floor heating brand ™ The world’s best-selling electric floor heating brand ™ SPEEDFIT-TEE INSTALLATION INSTRUCTIONS PTC Cores Outer jacket Copper Braid INSTALLATION INSTRUCTIONS Outer jacket Insulation Bus wires Cable with outer jacket for dry and wet conditions 1- Leave extra wire for connections and mishaps. 4• Push the braid back to create a bump. • Then use a screwdriver or similar to create an opening and slide the inner cable out of the braided ground mesh. • Do not cut the ground braid. 7- Separate bus wires from the solid carbon center and peel them off. 2- Insert the Pressure Seal End first and then the grommet for each cable. 5- Now expose the inner core cables and carbon matrix by carefully removing the inner jacket. Do not cut the conductor cables. 3• Do not cut the braiding. • Strip the outer jacket. • Slightly bend the cable where you made the cut to strip it. • • • • • • WARMUP INC. USA: us@warmup.com Tel.: 1-888-927-6333 www.warmup.com 8- Clear about 3-4” of the inner wires from the carbon matrix, then cut off the excess matrix in between. You should be left with a twisted ground braid, and two inner conductor cables about 3-4” long. 6- Twist the ground braid clean for future connection to screw connector. CANADA: ca@warmup.com Tel.: 1-888-592-7687 www.warmup.ca The world’s best-selling electric floor heating brand ™ The world’s best-selling electric floor heating brand ™ SPEEDFIT-TEE INSTALLATION INSTRUCTIONS 9• Using the glass cloth tape, put the ponytail brain against the inner jacket and do a minimum of 3 loops around the inner jacket. • Separate from the cable and loop a minimum of two times around the braid. • Install the grommet to the edge of the loop tape. Do not install grommet over the tape. 10• Install wire number 3 in the main box. • Install the grommet into the hole of the main box. • Push pressure seal end and then tight crews back into the main box. 11• Loosen the screw number 3. • Install wire number 3 on its base. • Tighten the screw back into position. • Cut all extra wire and braid. WARMUP INC. USA: us@warmup.com Tel.: 1-888-927-6333 www.warmup.com 12• Install the wires number 1&2 in the main box. • Install the grommet into the hole of the main box. • Push pressure seal end and then tight crews back into the main box. 13• Loosen the screws number 1&2. • Install wire number 1&2 on their base. • Tighten the screw back into position. • Cut all extra wire and braid. 14• Install the 2 gaskets and the 2 covers onto the main box. • Tighten the screw back into position 15• Affix the Low-Profile Tee Connection and side wires to the pipe using tape. • Affix insulation. • Install label on the of the insulation protector. • Give instructions to the owner/ user. CANADA: ca@warmup.com Tel.: 1-888-592-7687 www.warmup.ca The world’s best-selling electric floor heating brand ™
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2016:02:24 14:29:40-05:00 Metadata Date : 2016:02:24 14:29:41-05:00 Modify Date : 2016:02:24 14:29:41-05:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:c58c78f8-4161-48e8-8fda-80cf677a16a1 Original Document ID : xmp.did:4031EE556476E51195C3B11B0B6A23A0 Document ID : xmp.id:12FF6CEC2CDBE511BBF8951271E6FF12 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:11FF6CEC2CDBE511BBF8951271E6FF12 Derived From Document ID : xmp.did:C5495DFD72CBE5119962E5B26B2DB22B Derived From Original Document ID: xmp.did:4031EE556476E51195C3B11B0B6A23A0 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2016:02:24 14:29:40-05:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 3 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools