T10 4_01 S_T10 S
User Manual: S_T10
Open the PDF directly: View PDF .
Page Count: 4
|Open PDF In Browser||View PDF|
SunSet T10 TM April 2001 SPECIFICATIONS Connectors Bantam jacks, Line 1 and 2 Tx/Rx Serial Port: 8 DIN, RS232C (V.24), DTE Datacom Port: SCSI-36 system expansion port Test Mode T1SINGLE: T1 line testing T1DUAL: Bidirectional T1 line testing, DS0/VF channelized drop/insert, SS7 protocol analysis, ISDN PRI protocol analysis and call setup, DDS testing T1-MUX: Fractional T1 datacom port drop/insert testing DATACOM: V.35, RS449/V.36, X.21/V.11, RS232/V.24 Status/Alarm Indicators Power and low battery LED indicators 16 dual-color LED indicators for Line 1 & 2: Pulses, B8ZS, AIS, Yellow Alarm, SF-D4, ESF, SLC-96, Error Logical: Test Pattern Sync, bit error T1 Interface Framing: SF-D4, ESF, SLC-96 Coding: AMI, B8ZS Access Mode DSX Monitor: 100Ω, ±1% Bridge: > 1000Ω Terminated: 100Ω, ±1% Transmitter Line Build Out (LBO): 0, -7.5, -15, -22.5 dB Clock: Internal (1.544 MHz, ± 5 ppm), looped, external Pulse shape to TR-TSY-000499; reference: G.703, CB113, CB119, CB132, CB143, PUB62508, PUB62411 Receiver Terminate, Bridge: +6 to -36 dB cable loss DSXMON: -15 to -25 dB, resistive Frequency range: 1542 kHz to 1546 kHz Test Patterns Repeating: 3 in 24, 1 in 8 (1:7), 1 in 16, 55 octet, 55 Daly, Alt 1010, All 0s, All 1s, FOX, T1-T6, DDS1, DDS2, DDS3, DDS4, DDS6 Pseudo random: QRS, PRBS 2-n - 1, n = 6, 7, 9, 11, 15, 20, 23 Programmable: 10 patterns, 2048 bits long with user defined alphanumeric labels Test pattern inversion Error Injection BPV, logic, frame errors; programmable error burst 1 to 9999, or error rate 2 x 10-3 to 1 x 10-9 Measurements . . . a step ahead Error Types: BPV, Bit error, Framing bit error, CRC-6 error Error Reports: Total count, error rate, ES, %ES, SES, %SES, UAS, %UAS, AS, %AS, DGRM, %DGRM Alarm Statistics: AIS seconds, loss of signal seconds, Yellow Alarm seconds, loss of frame seconds, change of frame alignment seconds G.821 Analysis Signal Measurements Signal available seconds count and percent, loss of signal seconds count & percent, low density seconds count, excess 0s seconds count, AIS seconds count Receive bit rate: 1542 to 1546 kbps, ± 1 bps, ext/int clock Receive level (volts and dBdsx): Vpeak-peak, V+peak, V-peak Simplex current: 1 to 200 mA, ± 1 mA, ± 5% Frequency Measurements Moving bar graph of slip count, max frequency, min frequency, clock slips, frame slips, max positive wander, max negative wander General Measurement Duration: Continuous or timed (programmable from 1 min to 999 hours) Printing at timed interval or at end of test Printing on alarm or event with timestamp Error/Alarm events and test results may be stored in NVRam in absence of printer Other Measurements View Received Data View T1 data in binary, hex, ASCII Shows data in bytes by timeslot Trap 60 pages of data, 8 bytes per page Captures 256 consecutive timeslots and stores as user pattern Bridge Tap Automated transmission & measurement of 21 different patterns to identify possible bridge taps on line TM SunSet T10 Propagation Delay Measure roundtrip propagation delay in unit intervals ± 1 UI, with translation to microseconds and one way distance over cable Quick Tests Two programmable automated loopback tests that save time when performing standardized loopback tests CSU & NI Loopback Control In-band Codes CSU, NI, 100000 10 programmable user patterns ESF-FDL Payload, Line, Network 10 programmable user patterns HDSL Span Control Looping and control of HDSL equipment from DS1 access Supports loopback commands for HTU-C, HTU-R, HRU, HLU, HRE Graphical display updates with span status Includes SF/ESF modes, arm, disarm, loop up, loop down, timeout disable Westell & Teltrend Looping Device Control (SW184) Automated looping of Westell and Teltrend line and central office repeaters. Includes SF and ESF modes, arm, loop up/down, loopback query, sequential loopback, power loop query, span power down/up, unblocking ESF Facility Data Link (SW182) Read and Send T1.403 message on FDL (PRM and BOM) Automatic HDLC protocol handling YEL ALM, LLB ACT, LLB DEA, PLB ACT, PLB DEA T1.403 24 hour PRM collection per 15 min interval DDS Basic Package (SW188) Test from T1 interfaces Choose receive and transmit timeslots independently Test rates: 2.4, 4.8, 9.6, 19.2, 56, 64 kbps Patterns: 2047, 511, 127, 63, All 1s, All 0s, DDS-1, DDS-2, DDS-3, DDS-4, DDS-6, 8-bit user, Alt 1010 Loopbacks: Latching, interleaved. CSU, DSU, OCU, DSO-DP, 8-bit user Measurements: Bit errors, Bit error rate Control code send/receive: Abnormal, mux out-of-sync, idle Teleos & Switched 56 Tests (SW187) Switched 56 call setup and bit error rate testing Teleos signaling sequence timing analysis and dial digits decoding Fractional T1 Error measurements, channel configuration verification Nx64 kbps, Nx56 kbps, N=1 to 24 Sequential, alternating, or random channels Auto scan and auto configure to any FT1 order CSU & NI Emulation (SW181) Bidirectional Responds to loopback commands, in-band and out-of-band (ESF datalink T1.403) Graphic indication of incoming signal status in both directions Simultaneous display of T1 line measurements Automatic generation of AIS and Yellow alarm Loopbacks Line 1: Line and payload loopback Line 2: Line loopback Simultaneous loopbacks in both directions Local and remote loopback control Remote Control (SW180) SLC-96 Data Link (SW182) Send and receive message WP1, WP1B, NOTE formats Alarms, switch-to-protect, far end loop To Telcordia TR-TSY-000008 specifications, mode I and III VT100 emulation with same graphical interface used by test set Circuit status table provides current and historical information on test set LEDs Uses 8 pin MINI DIN, RS232C, 9600 baud preferred Voice Frequency Capabilities Westell & Teltrend PM NIU and MSS (SW184) Supports Westell and Teltrend performance monitoring network interface unit and maintenance switch system with ramp. Set/query NIU time and date. Query performance data by hour or all. Reset performance registers. Read data over RAMP line. Perform maintenance switch. Pulse Mask Analysis (SW190) Scan Period: 800 ns Measurements: Pass/Fail, rise time, fall time, pulse width, %overshoot, %undershoot Resolution: 1 ns or 1%, as applicable Masks: ANSI T1.102, T1.403; AT&T CB119, Pub 62411 Pulse/Mask Display: Test set screen and SS118 printer Monitor speaker with volume control for Line 1 and 2 Built-in microphone for talk View all 24 channel A, B (C, D) bits for Line 1 and 2 Control A, B (C, D) bits (E&M ground/loop start, FXO, FXS, on/off hook, wink) Companding law - µ Law Programmable idle channel A, B (C, D) bits Selectable idle channel code, 7F or FF hex VF Level and Frequency Measurement Level: +3 to -60 dBm, resolution 0.1 dBm Frequency: 50 to 3950 Hz, resolution 1 Hz VF tone generation Variable tone: 50 to 3950 Hz @ 1 Hz step, +3 to -60 dBm @ 1 dBm Fixed tones: 404, 1004, 1804, 2713, 2804 Hz @ 0 dBm and -13 dBm Noise Analysis (SW183) ISDN PRI (SW186) Signal to noise (S/N) Noise with filters: 3 kHz flat, C-message, C-notch Bidirectional monitoring and call analysis National ISDN-2, AT&T 5ESS, ETSI, and Northern Telecom DMS-100 compatible NT and TE emulation Voice and data call setup and receive Built-in microphone and speaker for B-channel talk/listen Supports multirate Nx64k data calls Generates 2047, 511, 127, 63, All 1s, All 0s, and user programmable 8-bit test patterns Bit error rate test with G.821 analysis Supports 23B+D, 47B+D, and 46B+2D Test for Backup D-channel in 46B+2D User programmable trace filter, view bidirectional real time message flow. Messages are interpreted up to layer 3 or displayed in hex format. Trace storage holds up to 1000 messages with timestamps On-screen help for special optional call feature programming MF/DTMF/DP Dialing, Decoding/Analysis (SW185) MF/DTMF/DP dialing up to 32 digits, 10 user programmable quick dial number for each tone type MFR1 digits, 0 - 9, KP, ST, ST1-3, Pause DTMF digits, 0 - 9, *, #, A, B, C, D, Pause DP digits, 0 - 9, Pause MF/DTMF decode up to 40 received digits. Analyze number, high/low frequencies, high/low levels, twist, tone period, interdigital time. Analyzer dynamic range: 0 to -25 dBm DP decode up to 40 digits. Analyze number, %break, PPS, interdigital time Programmable interdigital period, tone period, and tone level (MF, DTMF) Programmable %break and interdigital period @ 10 pps (DP) Signaling Analysis Analyze mode Tracer on A, B (C, D) signaling state changes for Line 1 and 2 with timestamps MFR1: Timing analysis of signaling transition states and dialing digits decoding of MFR1 signaling MFR1M: Modified MFR1 CO switches signaling analysis MIXTONE: Decode a signaling sequence that has both MF and DTMF digits Protocol Analysis SS7 (SW189A) Layer 2, 3, 4 analysis to bit level SU traffic analysis Counters for FISU, LSSU, TUP, ISUP, SNM, SNT messages Counters for FIB and BIB retransmissions % analysis on different types of messages MSU tracer User programmable trace filter; CIC, DPC, OPC, H1H0, Signaling address View bidirectional real time message flow Messages are interpreted up to layer 4 or displayed in hex format. The trace storage holds up to 1000 messages. SS7 TCAP Analysis (SW189B) ANSI T1.114 TCAP filter: And/or filtering on Origination and Destination Transaction ID Decoding: For Transaction, Dialogue, and Component Portions Transaction Portion decoding includes Package Type and Transaction ID Dialogue Portion decoding for Information Element Identifier and Context Component decode screen displays Component Type, Correlation ID, Operation Code (Operation Family & Operation Specifier), and Parameter Identifier and Contents GSM 16K Voice/TRAU Analysis (SW191) Supports GSM 06.10, 08.60 Drop/Monitor 16 kbps GSM channel at 13 kbps voice rate to built-in speaker Selectable timeslot (1 to 24) and subchannel (1 to 4) Codification RPE LTP at 13 kbps Frame type decode of 16 kbps subchannel (Voice, Data, Idle) Identify uplink or downlink direction Transmit encoded 13 kbps voice message on timeslot/subchannel BERT (G.821) on 16 kbps subchannel: Bit error/rate, ES, SES, EFS, UAS, LOSS Send test pattern on 16 kbps: 2047, All 1s, All 0s, Alt 1010 GR-303 Analysis (SW193) Bidirectional monitoring of TMC/CSC/EOC channels Tricordia GR-303-CORE TMC/CSC Monitoring Decode to Layer 3 Statistics counters for each cause value 1000 messages can be stored with date & timestamp, direction, and full L3 decode Trace filters for: Call Reference Value, DS0, DS1, Cause Value EOC Verification Decode to Layer 2 Errored or discarded frame counters Filter on SAPI/TEI combination Frame Relay Analysis (SW194) Supported from DS1 or V.35 interface Test Rate: 1.544 Mbps, Nx56 kbps, Nx64 kbps Supports ITU-T Q.933, ANSI T1.617 Mode: UNI DTE/DCE Requires factory installation LMI Analysis Auto configuration for protocol type Settings: T391 Status Enquiry, T393 Status, N391 Full Status Polling, N392 Error Threshold, N393 Monitor Events Results: Link O.K. Total, Link Errored Total, Timeout Error, Response Sequence Number, Wrong message PVC Status: New, Active, New & Active, or Inactive DLCI indication Datacom Interface (SS151) Supports V.35, X.21 (V.11), RS232 (V.24), RS449 (V.36) RS530 interfaces DTE, DCE Emulation SCSI-36 connector to test set: Adapter cables for V.35, X.21, RS232 (V.24), RS449 (V.36), RS530 Synchronous data rates: 300 bps to 1.544 Mbps Asynchronous data rates: 50 bps to 19.2 kbps (RS232V.24 only) Send test patterns and make G.821 measurements Bit error injection View transmit and receive signal status: TxD, TxC, RxD, RxC, DTR, RTS, CTS, DSR, RL, LL, RI Control signal leads: DTR, RTS, CTS, DSR, DCD, RL, LL, RI Invoke Local Loopback (LL), Remote Loopback (RL) Internal or received clock selectable Hitless 1.544k, Nx56k and Nx64k T1 drop and insert, via V.35, X.21 (V.11), RS232 (V.24), RS449 (V.36) interface; DCE mode only GENERAL Operating temperature: 0˚C to 50˚C Operating humidity: 5% to 90%, noncondensing Storage temperature: -20˚C to 70˚C Size: 2.4" (max.) x 4.2" (max.) x 10.5" Weight: 2.5 lb [1.1 kg] Battery operation time: 2 1/2 hr nominal AC operation: 110V/120V @ 60 Hz, or 220V/240V @ 50 Hz 3 year warranty on chassis 1 year warranty on accessories and battery ORDERING INFORMATION Test Set SunSet T10 Chassis Includes chassis, Software cartridge, NiMH battery, Universal Charger (SS138C), Instrument Stand, and User's Manual SW180 SW181 SW182 SW183 SW184 SW185 SW186 SW187 SW188 SW189A SW189B SW190 SW191 SW193 SW194 Remote control CSU/NIU Emulation ESF & SLC-96 Data Link Send and Receive VF Level, Frequency, and Noise Measurement Westell, Teltrend Intelligent Products MF/DTMF/DP Dialing, Decoding, and Analysis ISDN PRA (also known as PRI) Call Setup & D-channel Monitor Switched Call Setup and BERT DDS testing (T1 interface access) SS7 Protocol Analysis SS7 TCAP Analysis Pulse Mask Analysis GSM 16K Voice/TRAU Analysis GR-303 Analysis Frame Relay Analysis (Requires factory installation) Accessories SS101 SS104 SS105 SS106 SS107 SS108 SS109 SS110 SS111 SS112 SS115B SS116 SS117 SS118B SS122C SS123A SS127 SS128A SS130A SS130B SS132 SS136 SS138C SS152 SS252 SS253 SS254 SS255 SS262 SS308 Carrying case Cigarette lighter battery charger Repeater extender Single bantam to bantam cable, 6' Dual bantam to bantam cable, 6' Single bantam to 310 cable, 6' Single bantam to alligator clip cable, 6' Dual bantam to 15-pin D-sub connector cable, Male, 6' Dual bantam to 15-pin D-sub connector cable, Female, 6' 2 single bantams to RJ-48 8 position modular plug cable, 6' 8-pin mini DIN to DB9 Printer cable Instrument stand Printer paper, 5 rolls, for SS118 High capacity thermal printer. Includes SS115B. Null Modem Adapter SunSet jacket Printer 220VAC charger for SS118 120V/12V 1.2A SunSet Charger 19"/23" SunSet Rack Mount - Removable 19"/23" SunSet Rack Mount - Permanent Two single bantams to 4-position modular plug cable SunSet T10 User's Manual SunSet AC Adapter, 100-240 VAC, 50/60 Hz input, output 15 VDC @ 2A SunSet T10 Training Tape V.35 DTE/DCE Adapters X.21/V.11 DTE/DCE Adapters RS232/V.24 DTE/DCE Adapters RS449/V.36 DTE/DCE Adapters RS530 DTE/DCE Adapters Datacom Cable SCSI-36 (m) to DB-37 (f), 6' LE E TE C O M Datacom Module Includes cable adapters for V.35, RS449/V.36, X.21, RS232, DTE and DCE O SS151 Note: Specifications subject to change without notice. © 2001 Sunrise Telecom Incorporated. All rights reserved. Printed in USA. 0 IS Hardware Option N C. SUN IS ,I R SS150B Software Options 90 38 PING Testing Transmit and respond to PING messages Send Settings: DLCI length (2-4 bytes), DLCI value, Local IP, Destination IP, Network Layer Protocol Identifier (NLPID), Timeout, Number of PINGS Results: Number of PINGs, Number sent, PING status (received, unreached, errored), Round Trip Time (current, average, maximum, minimum) Response settings: Local IP Response results: PVC status, Number of PINGS, Number received, PING from IP address with timestamp 01 - A6 Your representative: Roman Porenta email@example.com Omnicor 1170 Foster City Blvd. Foster City, CA 94404 Phone: (650) 572 0122 Ext. 111 Fax: (650) 572 0533 www.omnicor.com 22 Great Oaks Blvd. San Jose, CA 95119 ph 1 408 363 8000 fax 1 408 363 8313 firstname.lastname@example.org www.sunrisetelecom.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2001:04:03 16:39:52Z Subject : T10 FINAL 4_01 Modify Date : 2002:11:15 22:18:03-08:00 Page Count : 4 Has XFA : No Creation Date : 2001:04:03 16:39:52Z Producer : Acrobat Distiller 4.0 for Macintosh Keywords : Author : Supriya Mody Mod Date : 2002:11:15 22:18:03-08:00 Metadata Date : 2002:11:15 22:18:03-08:00 Description : T10 FINAL 4_01 Title : T10 FINAL 4_01 Creator : Supriya ModyEXIF Metadata provided by EXIF.tools