F3400 Serve File
User Manual: F3400
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
DFT-022 F3930 DELFLEET® Evolution 5.0 VOC Conventional Clear F3930 is a premium quality clearcoat specifically formulated to give optimum gloss and durability. F3930 dries quickly and provides excellent polishing characteristics. Products Compatible Surfaces F3930 may be applied over: Conventional Clear F3930 High Solids Hardener F3200 • FBC Basecoat High Solids Hardener - Fast F3260 • FBCH High Solids Polyurethane Enamel Fast Thinner F3320 • FBCS High Solids Basecoat - Fast Medium Thinner F3330 • FDG Single Stage Polyurethane Slow Thinner F3340 • FDGH Single Stage High Solids Polyurethane Enamel Extra Slow Thinner F3350 • FDGU Single Stage Ultra High Solids Polyurethane Enamel Retarder F3360 Exempt Solvent F3385 Medium Solvent F3390 Slow Solvent F3395 Fast Dry Additive F3400 Medium Dry Additive F3405 Slow Dry Additive F3410 Product Information Effective 05/2017 DFT-022 Technical Data Sheet F3930 5.0 VOC Conventional Clear Always Check for an Updated Copy at www.ppgcommercialcoatings.com F3930 Application Data Selection of Substrate Cleaner: Code Product Purpose CFX435LV Low VOC Cleaner ONECHOICE® Commercial CFX Cleaners Compliant cleaner suitable for removing dirt, grease or other contaminants before or during the painting process. CFX436 Wax & Grease Remover Suitable for removing dirt, grease or other contaminants before or during the painting process. CFX437 Heavy Duty Wax & Grease Remover Used to remove heavy milling oils and grease from bare substrates prior to the painting process. Mixing Ratio: F3400/F3405/F3410 Pot Life @ 70ºF (21°C) / 50% RH: F3930 : F3260 : F33XX : per RTS gal. (Optional) 3 : 1 : 1 : 2 oz. 5 to 6 hours High heat and humidity will shorten pot life. Spray Viscosity: #2 ZAHN CUP #3 ZAHN CUP 25 seconds 11 seconds 17 seconds HVLP Conventional 1.2 – 1.6 mm 1.2 – 1.6 mm Air Pressure: 10 PSI at the cap 55 – 60 PSI Pressure Pot Set-up: 1.0 – 1.4 mm with 8 – 12 fluid ounces per minute 1.0 – 1.4 mm with 8 – 12 fluid ounces per minute Spray Gun Set-up: Fluid Tip: Number of Coats: 2 coats Allow 10 – 15 minutes flash time between coats Flash Off @ 70ºF (21°C) before force drying: 0–15 minutes Page 2 DFT-022 F3930 Always check for an updated copy at www.ppgcommercialcoatings.com 4DIN F3930 Application Data (continued) Dry Times: With F3200 With F3260 Dust-Free: 70ºF (21ºC) 45 minutes 30 minutes Tape Time: 68°F (20°C) 140°F (60°C) 8 hours 40 minutes 7 hours 40 minutes Overcoat/Recoat: 70°F (21°C) 140ºF (60ºC) Minimum 60 minutes to maximum 24 hours at 70ºF (21ºC) before sanding is required. After a force dry, scuff sand to a uniform dull appearance after cool down before recoating. * Force dry times are for quoted metal temperature. Additional time should be allowed in the force-drying schedule to allow metal to reach recommended temperature. Film Build: Wet (per coat) Minimum Theoretical Coverage: 5.0 mils Dry (total) 2.0 mils 690 sq. ft. Theoretical coverage in sq. ft. /US gal. Ready-to-spray (RTS), giving 1 mil. (25µm) dry film thickness (assuming 100% Transfer Efficiency). Physical Characteristics: VOC (Packaged): F3930 4.04 lbs./gal. or 485 g/L F3200 1.35 lbs./gal. or 162 g/L F3260 1.33 lbs./gal. or 160 g/L F33XX 7.13 lbs./gal. or 856 g/L F3400/F3405/F3410 8.14 lbs./gal. or 977 g/L VOC (Ready-To-Spray): 4.12 lbs./gal. or 494 g/L Total Solids By Weight (RTS): 46.43% Total Solids By Volume (RTS): 43.06% Page 3 DFT-022 F3930 Always check for an updated copy at www.ppgcommercialcoatings.com Safety Data Sheets (SDS) for the PPG products mentioned in this publication are available through www.ppgcommercialcoatings.com (Safety, SDS Search) or your PPG Distributor. Health and Safety: For additional information regarding this product, see the SDS and LABEL information. EMERGENCY MEDICAL OR SPILL CONTROL INFORMATION (412) 434-4515; IN CANADA (514) 645-1320 AND IN MEXICO 01-800-00-21-400. Materials described are designed for application by professional, trained personnel using proper equipment and are not intended for sale to the public. Products mentioned may be hazardous and should only be used according to directions, while observing precautions and warning statements listed on label. Statements and methods described are based upon the best information and practices known to PPG Industries. Procedures for applications mentioned are suggestions only and are not to be construed as representations or warranties as to performance, results, or fitness for any intended use, nor does PPG Industries warrant freedom from patent infringement in the use of any formula or process set forth herein. PPG Industries Commercial Coatings 19699 Progress Drive Strongsville, OH 44149 1-800-647-6050 © 2017 PPG Industries PPG Canada Inc. Commercial Coatings 2301 Royal Windsor Drive, Unit #6 Mississauga, Ontario L5J 1K5 1-888-310-4762 www.ppgcommercialcoatings.com The PPG Logo, Delfleet and OneChoice are registered trademarks of PPG Industries Ohio, Inc. Bringing innovation to the surface is a trademark of PPG Industries Ohio, Inc. Part No. DFT-022 05/2017
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Print high-res Language : en-US Tagged PDF : Yes XMP Toolkit : 3.1-701 Producer : Adobe PDF Library 15.0 Creator Tool : Adobe InDesign CC 2015 (Macintosh) Create Date : 2017:05:21 17:21:32-04:00 Modify Date : 2017:05:24 15:05:03-04:00 Page Count : 4 Creator : Adobe InDesign CC 2015 (Macintosh) Trapped : FalseEXIF Metadata provided by EXIF.tools