F3400 Serve File
User Manual: F3400
Open the PDF directly: View PDF 
.
Page Count: 4
F3930 is a premium quality clearcoat specifically formulated to give optimum gloss and
durability. F3930 dries quickly and provides excellent polishing characteristics.
DELFLEET® Evolution
F3930 5.0 VOC Conventional Clear
DFT-022
Products
Conventional Clear F3930
High Solids Hardener F3200
High Solids Hardener - Fast F3260
Fast Thinner F3320
Medium Thinner F3330
Slow Thinner F3340
Extra Slow Thinner F3350
Retarder F3360
Exempt Solvent F3385
Medium Solvent F3390
Slow Solvent F3395
Fast Dry Additive F3400
Medium Dry Additive F3405
Slow Dry Additive F3410
Compatible Surfaces
F3930 may be applied over:
• FBC Basecoat
• FBCH High Solids Polyurethane Enamel
• FBCS High Solids Basecoat - Fast
• FDG Single Stage Polyurethane
• FDGH Single Stage High Solids Polyurethane Enamel
• FDGU Single Stage Ultra High Solids Polyurethane Enamel
Product Information Effective 05/2017
DFT-022 Technical Data Sheet F3930 5.0 VOC Conventional Clear
Always Check for an Updated Copy at www.ppgcommercialcoatings.com
Code Product Purpose
CFX435LV Low VOC Cleaner Compliant cleaner suitable for
removing dirt, grease or other
contaminants before or during
the painting process.
CFX436 Wax & Grease Remover Suitable for removing dirt, grease
or other contaminants before or
during the painting process.
CFX437 Heavy Duty Wax & Used to remove heavy milling
Grease Remover oils and grease from bare
substrates prior to the painting
process.
Mixing Ratio: F3400/F3405/F3410
F3930 : F3260 : F33XX : per RTS gal. (Optional)
3 : 1 : 1 : 2 oz.
Pot Life @ 70ºF (21°C) /
50% RH: 5 to 6 hours
High heat and humidity will shorten pot life.
Spray Viscosity: #2 ZAHN CUP #3 ZAHN CUP 4DIN
25 seconds 11 seconds 17 seconds
Spray Gun Set-up: HVLP Conventional
Fluid Tip: 1.2 – 1.6 mm 1.2 – 1.6 mm
Air Pressure: 10 PSI at the cap 55 – 60 PSI
Pressure Pot Set-up: 1.0 – 1.4 mm with 1.0 – 1.4 mm with
8 – 12 fluid ounces 8 – 12 fluid ounces
per minute per minute
Number of Coats: 2 coats
Allow 10 – 15 minutes flash time between coats
Flash Off @ 70ºF (21°C)
before force drying: 0 –15 minute s
F3930 F3930
Application Data Application Data (continued)
Selection of
Substrate Cleaner:
ONECHOICE® Commercial
CFX Cleaners
Page 2 DFT-022 F3930
Always check for an updated copy at www.ppgcommercialcoatings.com
Dry Times: With F3200 With F3260
Dust-Free:
70ºF (21ºC) 45 minutes 30 minutes
Tape Time:
68°F (20°C) 8 hours 7 hours
140°F (60°C) 40 minutes 40 minutes
Overcoat/Recoat: Minimum 60 minutes to maximum 24 hours at 70ºF (21ºC)
70°F (21°C) before sanding is required. After a force dry, scuff sand to a
140ºF (60ºC) uniform dull appearance after cool down before recoating.
* Force dry times are for quoted metal temperature. Additional time should be allowed
in the force-drying schedule to allow metal to reach recommended temperature.
Film Build: Wet Dry
(per coat) (total)
Minimum 5.0 mils 2.0 mils
Theoretical Coverage: 690 sq. ft.
Theoretical coverage in sq. ft. /US gal. Ready-to-spray (RTS), giving 1 mil. (25µm) dry
film thickness (assuming 100% Transfer Efficiency).
Physical Characteristics: VOC (Packaged): F3930 4.04 lbs./gal. or 485 g/L
F3200 1.35 lbs./gal. or 162 g/L
F3260 1.33 lbs./gal. or 160 g/L
F33XX 7.13 lbs./gal. or 856 g/L
F3400/F3405/F3410 8.14 lbs./gal. or 977 g/L
VOC (Ready-To-Spray): 4.12 lbs./gal. or 494 g/L
Total Solids By Weight (RTS): 46.43%
Total Solids By Volume (RTS): 43.06%
F3930 F3930
Application Data Application Data (continued)
Page 3 DFT-022 F3930
Always check for an updated copy at www.ppgcommercialcoatings.com
PPG Industries PPG Canada Inc.
Commercial Coatings Commercial Coatings
19699 Progress Drive 2301 Royal Windsor Drive, Unit #6
Strongsville, OH 44149 Mississauga, Ontario L5J 1K5
1-800-647-6050 1-888-310-4762
© 2017 PPG Industries www.ppgcommercialcoatings.com Part No. DFT-022 05/2017
The PPG Logo, Deleet
and OneChoice
are registered trademarks of PPG Industries Ohio, Inc.
Bringing innovation to the surface is a trademark of PPG Industries Ohio, Inc.
For additional information regarding this product, see the SDS and LABEL information.
EMERGENCY MEDICAL OR SPILL CONTROL INFORMATION (412) 434-4515; IN CANADA (514) 645-1320
AND IN MEXICO 01-800-00-21-400.
Materials described are designed for application by professional, trained personnel using proper equipment and are not intended
for sale to the public. Products mentioned may be hazardous and should only be used according to directions, while observing
precautions and warning statements listed on label. Statements and methods described are based upon the best information and
practices known to PPG Industries. Procedures for applications mentioned are suggestions only and are not to be construed as
representations or warranties as to performance, results, or fitness for any intended use, nor does PPG Industries warrant freedom
from patent infringement in the use of any formula or process set forth herein.
Health and Safety: Safety Data Sheets (SDS) for the PPG products mentioned in this publication
are available through www.ppgcommercialcoatings.com (Safety, SDS Search)
or your PPG Distributor.
