Millennium 4 Mnl M4092 Rev Logitech Universal Remote IRC600 Shaw TV User Guide
4 to the manual 2ed10421-db62-47e5-8309-d6b9f6886690
User Manual: Logitech Universal Remote IRC600
Open the PDF directly: View PDF 
.
Page Count: 32
| Download | |
| Open PDF In Browser | View PDF |
Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM MILLENNIUM™ 4 Universal Remote Control User’s Guide Page 1 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features And Functions . . . . . . . . . . . . . . . . . . . . . . 4 Key Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Programming TV Control . . . . . . . . . . . . . . . . . . . . . 8 Setup Codes for TVs . . . . . . . . . . . . . . . . . . . . . . . . 8 Programming VCR/DVD Player Control . . . . . . . . 12 Setup Codes for VCRs. . . . . . . . . . . . . . . . . . . . . . 13 Setup Codes for DVD Players. . . . . . . . . . . . . . . . . 15 Programming TV/VCR Combo Control . . . . . . . . 16 Setup Codes for TV/VCRs . . . . . . . . . . . . . . . . . . . 17 Programming Cable Converter (or DBS Receiver) Control . . . . . . . . . . . . . . . . . . . 18 To Unlock the CBL Key. . . . . . . . . . . . . . . . . . . . . . 18 To Program the CBL Key . . . . . . . . . . . . . . . . . . . . 19 To Lock the CBL Key . . . . . . . . . . . . . . . . . . . . . . . 20 Setup Codes for Cable Converters. . . . . . . . . . . . . 20 Setup Codes for DBS Receivers. . . . . . . . . . . . . . . 20 Programming Channel Control Lock . . . . . . . . . . 21 To Activate Channel Control Lock . . . . . . . . . . . . . 21 To De-Activate Channel Control Lock. . . . . . . . . . . 21 Programming Audio Control . . . . . . . . . . . . . . . . . 22 Setup Codes for Audio Amplifiers . . . . . . . . . . . . . 22 Setup Codes for Audio Receivers. . . . . . . . . . . . . . 23 Searching For Your Code . . . . . . . . . . . . . . . . . . . . 24 Checking The Codes . . . . . . . . . . . . . . . . . . . . . . . 25 Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . 26 Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . 27 To Change Volume Lock to the Cable Mode . . . . . . 27 To Change Volume Lock to the TV Mode. . . . . . . . . 27 To Change Volume Lock to the VCR Mode . . . . . . . 27 To Change Volume Lock to the Audio Mode . . . . . . 28 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Additional Information . . . . . . . . . . . . . . . . . . . . . . 30 2 Page 2 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM INTRODUCTION The Universal Electronics Millennium™ 4 is our latest generation universal remote control. It is designed with sophisticated technology that will allow you to finally consolidate the clutter of all of the original remote controls in your home entertainment system. It’s packed with easyto-use features such as: • Preprogrammed to operate the cable converter supplied by your cable system provider • Preprogrammed technology for easy setup • Convenient hide-away sliding door to conceal less-used functions • Color-coded keys to quickly locate popular functions • Cable ID Lock to lock your remote control for use only with the cable converter • Channel Lock to lock channel selection only to the cable converter • Code library for video and audio components • Code Search to help program control of older or discontinued components Before you can use your new remote control, you will need to program it to operate the specific home entertainment components you wish to control. Follow the instructions detailed in this manual to set up your Millennium 4 and enjoy your new remote control. 3 Page 3 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM FEATURES AND FUNCTIONS Use the illustration below to locate Millennium 4 features and then study the Key Charts (on the next two pages) to learn how they function. 4 Page 4 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Key Charts The LED (red light) blinks to show that the remote control is working and is sending signals. Press AUDIO, VCR, TV, or CBL once to select a home entertainment component to control. Press POWER once to turn on or off the selected home entertainment component. Use SETUP for all programming sequences. Use the keypad (0 ~ 9) to directly select channels (e.g., 09 or 31). Press MUTE once to turn sound off or on. Press ENTER once after entering channel numbers on some TV models. Use VOL+ (or VOL-) to raise (or lower) the sound volume. Use CH+ (or CH-) to select the next higher (or lower) channel. Press LAST once to recall the last channel and to page back one screen in the main menu. Use FAV to cycle through your favorite channels that are stored in your cable converter. Use GUIDE to display the program guide. Press PPV/LOCK once to display the pay per view menu or to lock out a specific channel on your cable converter. Use EXIT to exit out of your cable converter’s menu and guide. continued on next page... 5 Page 5 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM FEATURES AND FUNCTIONS Key Charts (continued) Use cursor keys to move the cursor in the program guide and menu screens. Use SELECT/OK to choose options, PPV events, and to tune programs from the program guide. Use INFO to display current channel and program information. Press MENU once to display your cable converter’s screen menu. Use PAGE ▲ (or PAGE ▼) to page up or down) through menu screens and the program guide. Slide the door open to reveal less-often used keys such as VCR transport buttons and cable converter features. In the VCR and TV modes, use the REW, PLAY, FF, REC, STOP, and PAUSE keys to control your VCR. To record a program, press REC twice. Reserved for cable converter features (see your cable converter manual). Press TV/VCR once to switch the VCR to view TV channels or tape. This key will also control the input select feature on most TVs. 6 Page 6 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM INSTALLING BATTERIES ❶ ❷ ❸ 1. On the back of the Millennium 4, push the tab and lift off the battery cover. 2. Obtain two (2) fully-charged AA alkaline batteries. Match the + and – marks on the batteries to the + and – marks in the battery case, then insert the new batteries. 3. Press the battery cover back into place. The tab should click when the cover is locked. 4. Test the unit by pressing POWER and any mode key (e.g. AUDIO, VCR, TV, or CBL). If the batteries are inserted correctly, the LED will blink once. NOTE: Whenever batteries need replacement, the Millennium 4 will blink twice with every key press. Simply replace the batteries and the Millennium 4 will be restored to its full functionality, complete with your favorite settings. 7 Page 7 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM PROGRAMMING TV CONTROL NOTE: If you own a TV/VCR combination, skip this section and perform “Programming TV/VCR Combo Control” on page 16. Locate the brand name of your TV in the Setup Codes for TVs in the next section, and write it in the space below. TV Brand: __________________________________ The brands are listed in alphabetical order with the most popular codes listed first.You will use one of these codes to program the Millennium 4 to operate your TV: 1. Turn on the TV. 2. On the Millennium 4, press TV once. Press and hold SETUP until the LED blinks twice, then release SETUP. 3. Enter the first four-digit code for your TV. If you perform this procedure correctly, the LED will blink twice. NOTE: If the LED did not blink twice after entering the code’s last digit, then repeat steps 2 through 3 and try entering the same code again. 4. Aim the Millennium 4 at your TV and press POWER once. The TV should turn off. If it does not, repeat steps 2 and 3, trying each code for your brand until you find one that works. If it still does not work, try searching for the code (see Searching For Your Code on page 24). 5. For future reference, write your TV code in the boxes below. NOTE: Remember, to use the Millennium 4 to operate your TV, press TV first. Setup Codes for TVs: AOC Admiral Aiko Akai Alaron America Action Anam Audiovox Baysonic 0030, 0019 0093, 0463 0092 0030 0179 0180 0180 0451, 0180, 0623, 0092 0180 8 Page 8 Millennium 4 Mnl M4092 rev Belcor Bell & Howell Bradford Brockwood Broksonic CXC Candle Carnivale Carver Celebrity Cineral Citizen Concerto Contec Craig Crosley Crown Curtis Mathes Daewoo Daytron Denon Dumont Electroband Emerson Envision Fisher Fujitsu Funai Futuretech GE Gibralter GoldStar Gradiente Grunpy Hallmark Harley Davidson Harman/Kardon Harvard Hitachi Infinity Inteq JBL JCB JVC KEC KTV Kenwood Konka LG 1/22/03 9:38 AM 0019 0154, 0016 0180 0019 0236, 0463 0180 0030, 0056 0030 0054 0000 0451, 0092 0060, 0030, 0056, 0092, 0280 0056 0180 0180 0054 0180 0047, 0747, 0054, 0154, 0051, 0451, 0093, 0060, 0030, 0056, 0145, 0016, 0166 0451, 0019, 0623, 0624, 0092 0019 0145 0017, 0019 0000 0154, 0236, 0463, 0180, 0178, 0179, 0019, 0623, 0624, 0282, 0280 0030 0154 0179, 0683 0180, 0179, 0171 0180 0047, 0747, 0051, 0451, 0093, 0178, 0021, 0282 0017, 0030, 0019 0030, 0178, 0056, 0019 0053, 0056 0180, 0179 0178 0179 0054 0180 0056, 0145, 0016 0054 0017 0054 0000 0053 0180 0180, 0030, 0280 0030, 0019 0707, 0628, 0632, 0638, 0703 0056 continued on next page... 9 Page 9 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM PROGRAMMING TV CONTROL Setup Codes for TVs (continued): LXI Logik Luxman MGA MTC Magnavox Majestic Marantz Matsushita Megatron Memorex Midland Minutz Mitsubishi Motorola Multitech NAD NEC NTC Nikko Onwa Optimus Optonica Orion Panasonic Penney Philco Philips Pilot Pioneer Portland Prism Proscan Proton Pulsar Quasar RCA RadioShack Realistic Runco SSS Sampo Samsung Sansei Sansui Sanyo Scimitsu 0047, 0747, 0054, 0154, 0156, 0178 0016 0056 0150, 0030, 0178, 0019 0060, 0030, 0056, 0019 0054, 0030, 0179 0016 0054, 0030 0250 0178, 0145 0154, 0250, 0463, 0150, 0178, 0179, 0056, 0016 0047, 0747, 0017, 0051 0021 0093, 0150, 0178, 0019 0093 0180 0156, 0178, 0166 0030, 0056, 0019 0092 0030, 0178, 0092 0180 0154, 0250, 0166 0093, 0165 0236, 0463, 0179 0051, 0250 0047, 0747, 0156, 0051, 0060, 0030, 0178, 0021, 0056, 0019 0054, 0463, 0030, 0145, 0019 0054 0030, 0019 0166 0019, 0092 0051 0047, 0747 0178 0017, 0019 0051, 0250, 0165 0047, 0747, 0090, 0051, 0093, 0019, 0278 0047, 0747, 0154, 0180, 0030, 0178, 0056, 0019, 0165 0154, 0180, 0030, 0178, 0056, 0019, 0165 0017, 0030 0180, 0019 0030 0060, 0030, 0178, 0056, 0019 0451 0463 0154 0019 10 Page 10 Millennium 4 Mnl M4092 rev Scotch Scott Sears Semivox Semp Sharp Shogun Signature Sony Soundesign Squareview Starlite Supreme Sylvania Symphonic TMK TNCi Tandy Technics Technol Ace Techwood Teknika Telefunken Toshiba Vector Research Victor Vidikron Vidtech Wards White Westinghouse Yamaha Zenith 1/22/03 9:38 AM 0178 0236, 0180, 0178, 0179, 0019 0047, 0747, 0054, 0154, 0156, 0178, 0179, 0056, 0171 0180 0156 0093, 0688, 0165 0019 0016 0000 0180, 0178, 0179 0171 0180 0000 0054, 0030 0180, 0171 0178, 0056 0017 0093 0051, 0250 0179 0051, 0056 0054, 0180, 0150, 0060, 0179, 0056, 0019, 0016, 0092 0056 0154, 0156, 0060 0030 0053 0054 0178, 0019 0054, 0030, 0178, 0021, 0179, 0056, 0019, 0016, 0165 0463, 0623, 0624 0030, 0019 0017, 0463, 0624, 0016, 0092 11 Page 11 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM PROGRAMMING VCR/DVD PLAYER CONTROL NOTE: If you own a TV/VCR combination, skip this section and perform “Programming TV/VCR Combo Control” on page 16. Locate the brand name of your VCR in Setup Codes for VCRs on the next page, or your DVD player in Setup Codes for DVD Players on page 15, and write it in the appropriate space below. VCR Brand: ________________________________ or DVD Player Brand: ____________________________ The brands are listed in alphabetical order with the most popular codes listed first.You will use one of these codes to program the Millennium 4 to operate your VCR or DVD player: 1. Turn on your VCR and insert a video cassette, or turn on your DVD player and insert a DVD. 2. On the Millennium 4, press VCR once. Press and hold SETUP until the LED blinks twice, then release SETUP. 3. Enter the first four-digit code for your VCR or DVD player. If you perform this procedure correctly, the LED will blink twice. NOTE: If the LED did not blink twice after entering the code’s last digit, then repeat steps 2 through 3 and try entering the same code again. 4. Aim the Millennium 4 at the VCR or DVD player and press POWER once. The device should turn off. If your VCR remote control does not have a POWER key, press PLAY. If the VCR does not respond, repeat steps 2 and 3, trying each code listed for your brand until you find one that works. If the device still does not work , try searching for the code (see Searching For Your Code on page 24). 5. For future reference, write your device’s code and type in the boxes and space below. Device Type:________________________ NOTE: Remember, to use the Millennium 4 to operate your VCR or DVD player, press VCR first. 12 Page 12 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Setup Codes for VCRs: Admiral Adventura Aiko Aiwa Akai America Action American High Asha Audiovox Beaumark Bell & Howell Broksonic CCE Calix Canon Carver Cineral Citizen Colt Craig Curtis Mathes Cybernex Daewoo Denon Dynatech Electrohome Electrophonic Emerex Emerson 0048, 0209 0000 0278 0037, 0000 0041 0278 0035 0240 0037 0240 0104 0184, 0121, 0209, 0002, 0479, 0295 0072, 0278 0037 0035 0081 0278 0037, 0278 0072 0037, 0047, 0240, 0072 0035, 0060, 0162, 0041 0240 0045, 0278, 0561 0042 0000 0037 0037 0032 0037, 0184, 0000, 0121, 0043, 0209, 0002, 0278, 0479, 0561, 0295, 0294 Fisher 0047, 0104 Fuji 0035, 0033 Funai 0000 GE 0035, 0060, 0048, 0240 Garrard 0000 Go Video 0432, 0526, 0643, 0232, 0279 GoldStar 0037 Gradiente 0000 HI-Q 0047 Harley Davidson 0000 Harman/Kardon 0081 Harwood 0072 Headquarter 0046 Hitachi 0000, 0042, 0041, 0105 Hughes Network Sys. 0042 JVC 0067, 0041 Jensen 0041 KEC 0037, 0278 KLH 0072 continued on next page... 13 Page 13 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM PROGRAMMING VCR/DVD PLAYER CONTROL Setup Codes for VCRs (continued): Kenwood Kodak LXI Lloyd’s Logik MEI MGA MGN Technology MTC Magnasonic Magnavox Magnin Marantz Marta Matsushita Memorex Minolta Mitsubishi Motorola Multitech NEC Nikko Noblex Olympus Optimus Orion Panasonic Penney Pentax Philco Philips Pilot Pioneer Polk Audio Profitronic Proscan Protec Pulsar Quarter Quartz Quasar RCA RadioShack Radix Randex Realistic 0067, 0041 0035, 0037 0037 0000 0072 0035 0240, 0043 0240 0000, 0240 0278 0035, 0039, 0081, 0000 0240 0035, 0081 0037 0035, 0162, 0454 0035, 0037, 0048, 0039, 0047, 0162, 0000, 0240, 0104, 0209, 0454, 0479, 0046 0042, 0105 0048, 0067, 0043 0035, 0048 0000, 0072 0067, 0104, 0041 0037 0240 0035 0037, 0048, 0162, 0104, 0454, 0432 0184, 0209, 0002, 0479, 0295 0035, 0225, 0162, 0454, 0616 0035, 0037, 0042, 0240 0042, 0105 0035, 0209, 0479 0035, 0081, 0618 0037 0067 0081 0240 0060 0072 0039 0046 0046 0035, 0162, 0454 0035, 0060, 0048, 0042, 0240, 0105, 0060 0000 0037 0037 0035, 0037, 0048, 0047, 0000, 0104, 0046 14 Page 14 Millennium 4 Mnl M4092 rev ReplayTV Runco STS Samsung Samtron Sanky Sansui Sanyo Scott Sears Semp Sharp Shintom Shogun Singer Sony Sylvania Symphonic TMK Tatung Teac Technics Teknika Thomas Tivo Toshiba Totevision Unitech Vector Video Concepts Videosonic Wards White Westinghouse XR-1000 Zenith 1/22/03 9:38 AM 0614, 0616 0039 0042 0045, 0240 0643 0048, 0039 0000, 0067, 0209, 0041, 0479 0047, 0240, 0104, 0046 0184, 0045, 0121, 0043 0035, 0037, 0047, 0000, 0042, 0104, 0046, 0105 0045 0048 0072 0240 0072 0035, 0032, 0000, 0636, 0033 0035, 0081, 0000, 0043 0000 0240 0041 0000, 0041 0035, 0162 0035, 0037, 0000 0000 0618, 0636 0045, 0043 0037, 0240 0240 0045 0045 0240 0035, 0060, 0048, 0047, 0081, 0000, 0042, 0240, 0072 0209, 0072, 0278 0035, 0000, 0072 0039, 0000, 0209, 0479, 0033 Setup Codes for DVD Players: Aiwa Apex B&K Denon Fisher GE Gradiente Harman/Kardon Hitachi Hiteker JVC Kenwood 0641 0672 0655, 0662 0490, 0634 0670 0522 0651 0582 0573, 0664 0672 0558, 0623 0534, 0682 continued on next page... 15 Page 15 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM PROGRAMMING VCR/DVD PLAYER CONTROL Setup Codes for DVD Players (continued): Konka Magnavox Marantz Mitsubishi Onkyo Optimus Oritron Panasonic Philips Pioneer Proscan RCA Samsung Sharp Sherwood Sony Technics Techwood Theta Digital Toshiba Yamaha Zenith 0711, 0719, 0720, 0721 0503, 0675 0539 0521 0503, 0627 0571 0651 0490, 0677, 0632, 0678, 0679 0503, 0539 0525, 0571, 0632 0522 0522, 0571 0573 0630 0633 0533 0490 0692 0571 0503 0490, 0545 0503, 0591 PROGRAMMING TV/VCR COMBO CONTROL Locate the brand name of your TV/VCR Combo in Setup Codes for TV/VCR Combos on the next page, and write it in the space below. TV/VCR Combo Brand: ________________________ The brands are listed in alphabetical order with popular codes listed first.You will use one of these codes to program the Millennium 4 to operate your TV/VCR Combo: 1. Turn on your TV/VCR Combo and insert a video cassette. 2. On the Millennium 4, press VCR once. Press and hold SETUP until the LED blinks twice, then release SETUP. 3. Enter the first four-digit code for your TV/VCR Combo. If you perform this procedure correctly, the LED will blink twice. 16 Page 16 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM NOTE: If the LED did not blink twice after entering the code’s last digit, then repeat steps 2 through 3 and try entering the same code again. 4. Aim the Millennium 4 at your TV/VCR Combo and press POWER once. The unit should turn off. If it does not respond, repeat steps 2 and 3, trying each code listed for your brand until you find one that works. If it still does not work, try searching for the code (see Searching For Your Code on page 24). 5. If you’ve found a TV/VCR setup code that works your TV/VCR Combo and a separate TV code is also listed, you’ll need to program this code into the Millennium 4 to access volume control (see Programming TV Control on page 8). If there is no separate TV code listed, you will need to perform the following steps to access volume control: a. Press and hold SETUP until the LED blinks twice, then release SETUP. b. Enter 9 - 9 - 3. The LED will blink twice. c. Press VCR once. The LED will blink twice. 6. For future reference, write your TV/VCR Combo code in the boxes below. NOTE: Remember, to use the Millennium 4 to operate your TV/VCR Combo, press VCR first. Setup Codes for TV/VCR Combos: American High Brocksonic Colt Curtis Mathis Daewoo Emerson Funai GE Hitachi HQ Lloyds MGA Magnavox 0035 (for TV use 0051) 0002, 0294, 0072 0035 (for TV use 0051) 0278 0002, 0294, 0479 0000 0035 (for TV use 0051), 0060 (for TV use 0047), 0048 (for TV use 0093), 0240 0035 (for TV use 0051), 0000 0000 0000 0240 0081 (for TV use 0054), 0035 (for TV use 0051), 0000 continued on next page... 17 Page 17 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM PROGRAMMING TV/VCR COMBO CONTROL Setup Codes for TV/VCR Combos (continued): Magnin Memorex Mitsubishi Orion Panasonic Penney Quasar RCA Sansui Sanyo Sears Sharp Sony Symphonic Zenith 0240 0037, 0162 (for TV use 0250) 0048 (for TV use 0093) 0002, 0294, 0479 0035 (for TV use 0051), 0162 (for TV use 0250) 0035 (for TV use 0051), 0240, 0162 (for TV use 0250) 0035 (for TV use 0051), 0162 (for TV use 0250) 0060 (for TV use 0047), 0035 (for TV use 0051), 0048 (for TV use 0093) 0000, 0479 0240 0000, 0037 0048 (for TV use 0093) 0032 (for TV use 0000) 0000 0000 PROGRAMMING CABLE CONVERTER (OR DBS RECEIVER) CONTROL The Millennium 4 is preprogrammed at the factory to operate the cable converter given to you by your cable company. However, if you have another brand or model of cable converter or satellite receiver that you would like to control, then you’ll need to perform the following instructions to unlock the cable key, enter in a new code, and lock the cable key again. To Unlock the CBL Key: 1. Turn on the Cable Converter or DBS Receiver. 2. On the Millennium 4, press CBL once. Press and hold SETUP until the LED blinks twice, then release SETUP. 3. Enter 9 - 9 - 7. The LED will blink twice. 4. Press CH- once. The LED will blink twice. 18 Page 18 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM To Program the CBL Key: 1. On the next page, locate the brand name of your Cable Converter in Setup Codes For Cable Converters, or DBS (Direct Broadcast Satellite) Receiver in Setup Codes For DBS Receivers, and write it in the appropriate space below. Cable Converter Brand: ________________ or DBS Receiver Brand: __________________ The brands are listed in alphabetical order with the most popular codes listed first.You will use one of these codes to reprogram the Millennium 4 to operate your Cable Converter or DBS Receiver. 2. On the Millennium 4, press CBL once. Press and hold SETUP until the LED blinks twice, then release SETUP. 3. Enter the first four-digit code for your Cable Converter or DBS Receiver. If you perform this procedure correctly, the LED will blink twice. NOTE: If the LED did not blink twice after entering the code’s last digit, then repeat steps 2 through 3 and try entering the same code again. 4. Aim the Millennium 4 at your Cable Converter or DBS Receiver and press POWER once. The unit should turn off. If it does not respond, repeat steps 2 and 3, trying each code listed for your brand until you find one that works. If it still does not work , try searching for the code (see Searching For Your Code on page 24). 5. For future reference, write your device’s code and type in the boxes and space below. Device Type:________________________ NOTE: Remember, to use the Millennium 4 to operate your Cable Converter or DBS Receiver, press CBL first. continued on next page... 19 Page 19 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM PROGRAMMING CABLE CONVERTER (OR DBS RECEIVER) CONTROL (continued) To Lock the CBL Key: 1. On the Millennium 4, press CBL once. Press and hold SETUP until the LED blinks twice, then release SETUP. 2. Enter 9 - 9 - 7. The LED will blink twice. 3. Press CH+ once. The LED will blink twice. Setup Codes for Cable Converters: ABC Americast Bell South General Instrument GoldStar Hamlin Jerrold Memorex Panasonic Paragon Philips Pioneer Pioneer Pulsar Quasar Regal Runco Samsung Scientific Atlanta Starcom Toshiba Zenith 0003, 0008 0899 0899 0476 0144 0273 0003, 0476 0000 0000 0000 0305 0144, 0877, 0533 0533 0000 0000 0273 0000 0144 0008, 0477, 0877 0003 0000 0525, 0000, 0899 Setup Codes for DBS Receivers: Echostar 0775, 1005 Expressvu 0775 GE 0566 General Instrument 0869, 0892 HTS 0775 Hughes Network Sys. 0749 JVC 0775 Mitsubishi 0749 20 Page 20 Millennium 4 Mnl M4092 rev Next Level Philips Proscan RCA RadioShack Samsung Sony Star Choice Toshiba 1/22/03 9:38 AM 0869, 0892 0749, 1076 0392 0566, 0392 0869 1109 0639 0869 0749 PROGRAMMING CHANNEL CONTROL LOCK By activating this feature, the Millennium 4 will only allow access to the channel control capabilities of your cable converter. This will guarantee that you do not inadvertently change the channel on your TV or VCR. To Activate Channel Control Lock: 1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. 2. Enter 9 - 9 - 6. The LED will blink twice. 3. Press CH+ once. The LED will blink twice. 4. Now, regardless of what mode you select (i.e., TV, VCR, or CBL), only the channel control capability of your cable converter will be accessible. NOTE: This feature does not affect the Audio mode. To De-Activate Channel Control Lock: 1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. 2. Enter 9 - 9 - 6. The LED will blink twice. 3. Press CH- once. The LED will blink twice. 4. The Millennium 4 will again provide TV and VCR channel control capabilities while in the TV or VCR mode. 21 Page 21 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM PROGRAMMING AUDIO CONTROL Locate the brand name of your audio amplifier or receiver in one of the accompanying code lists at the end of this section.Write it in the appropriate space below. Audio Amplifier Brand: ________________________ or Audio Receiver Brand:__________________________ The brands are listed in alphabetical order with popular codes listed first.You will use one of these codes to program the Millennium 4 to operate your audio device: 1. Turn on the audio device. 2. On the Millennium 4, press AUDIO once. Press and hold SETUP until the LED blinks twice, then release SETUP. 3. Enter the first four-digit code for your audio device. If you perform this procedure correctly, the LED will blink twice. NOTE: If the LED did not blink twice after entering the code’s last digit, then repeat steps 2 through 3 and try entering the same code again. 4. Aim the Millennium 4 at your audio device and press POWER once. The unit should turn off. If it does not respond, repeat steps 2 and 3, trying each code listed for your brand until you find one that works. If it still does not work , try searching for the code (see Searching For Your Code on page 24). 5. For future reference, write your device’s code and type in the boxes and space below. NOTE: Remember, to use the Millennium 4 to operate your audio device, press AUDIO first. Setup Codes for Audio Amplifiers: Denon GE Harman/Kardon JVC Marantz 0160 0078 0892 0331 0892 22 Page 22 Millennium 4 Mnl M4092 rev Optimus Panasonic Philips Polk Audio Realistic Sony Soundesign Technics Victor Wards Yamaha 1/22/03 9:38 AM 0395 0308 0892 0892 0395 0689 0078 0308 0331 0078 0354 Setup Codes for Audio Receivers: ADC Adcom Aiwa Capetronic Carver Casio Clarinette Denon Garrard Harman/Kardon JBL JVC Kenwood Lloyd’s MCS Magnavox Marantz Modulaire Nakamichi Onkyo Optimus Panasonic Penney Philips Pioneer Proscan Quasar RCA Realistic Sansui Sharp Sony Soundesign Sunfire Teac Technics 0531 0616 1405, 0121, 0405 0531 0008 0195 0195 1104, 1160 0463 0110, 0891 0110 0074 1313, 1027, 1570, 1569, 0186, 0077 0195 0039, 0346 0531, 0195, 0391 0039 0195 0097 0135 1023, 0531, 0670, 0186, 0177 1518, 0039 0195 1269, 1120, 0391 1023, 0531, 0014, 0150, 0630 1254 0039 1023, 1254, 0531, 0054, 0346 0195 0346 0186 1058 0670 1313 0463 1308, 1309, 1518, 0039 continued on next page... 23 Page 23 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM PROGRAMMING AUDIO CONTROL Setup Codes for Audio Amplifiers (continued): Victor Wards Yamaha Yorx Zenith 0074 0014, 0054 0176, 1176, 0186 0195 0857 SEARCHING FOR YOUR CODE If your TV,VCR or DVD Player, Cable Converter, or Audio Component does not respond to the Millennium 4 after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code. For example, to search for a code for your TV: 1. Turn on your TV. 2. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. 3. Enter 9 - 9 - 1. The LED will blink twice. 4. Aim the remote control at the the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off. NOTE: In the search mode, the Millennium 4 will send IR codes from its library to the selected component, starting with the most popular code first. 5. Press SETUP once to lock in the code. 6. To search for the codes of your other components, repeat steps 1 through 5, but substitute the appropriate key (i.e., VCR, CBL, or AUDIO) for the (VCR or DVD, Cable, or Audio) component you are searching for. 24 Page 24 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM CHECKING THE CODES If you have set up the Millennium 4 using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment: For example, to find out which code is operating your TV: 1. Turn on your TV. 2. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. 3. Enter 9 - 9 - 0. The LED will blink twice. 4. To view the code for the first digit, press 1 once. Wait 3 seconds and count the number of LED blinks (e.g., 3 blinks = 3) and write down the number in the leftmost TV Code box below. NOTE: If a code digit is “0”, the LED will not blink. 5. Repeat step 4 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. Finish writing down the code in the TV Code boxes below. 6. To check for the codes of your other components, repeat steps 1 through 5, but substitute the appropriate key (i.e., VCR, CBL, or AUDIO) for the (VCR or DVD, Cable, or Audio) component you are checking.Write down the codes in the appropriate boxes below. TV Code VCR (or DVD Player) Code CBL Code AUDIO ___________________ Code 25 Page 25 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM RE-ASSIGNING DEVICE KEYS The Millennium 4 can be set up to control a second TV or VCR, or any combination of four home entertainment components. For example, to have the Millennium 4 control a TV, a Cable Converter, and two VCRs, you will need to re-assign the unused AUDIO key to operate the second VCR as follows: 1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. 2. Enter 9 - 9 - 2. The LED will blink twice. 3. Press VCR once, then press AUDIO once. 4. The AUDIO key is now ready to be programmed for your second VCR. See Programming VCR/DVD Player Control on page 12. To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the following chart for a desired component: To Re-Assign Perform Key Sequence TV as 2nd VCR key: SETUP - 9 - 9 - 2 - VCR - TV TV as 2nd Audio key: SETUP - 9 - 9 - 2 - AUDIO - TV TV as 2nd Cable key: SETUP - 9 - 9 - 2 - CBL - TV TV back to TV: SETUP - 9 - 9 - 2 - TV - TV VCR as 2nd TV key: SETUP - 9 - 9 - 2 - TV - VCR VCR as 2nd Audio key: SETUP - 9 - 9 - 2 - AUDIO - VCR VCR as 2nd Cable key: SETUP - 9 - 9 - 2 - CBL - VCR VCR back to VCR: SETUP - 9 - 9 - 2 - VCR - VCR AUDIO as 2nd TV key: SETUP - 9 - 9 - 2 - TV - AUDIO AUDIO as 2nd VCR key: SETUP - 9 - 9 - 2 - VCR - AUDIO AUDIO as 2nd Cable key: SETUP - 9 - 9 - 2 - CBL - AUDIO AUDIO back to AUDIO: SETUP - 9 - 9 - 2 - AUDIO - AUDIO Upon completion of a re-assignment, the LED will blink twice to confirm your selection.At that time, you will also need to program the Millennium 4 to control the new component. See previous sections on Programming TV Control, Programming VCR/DVD Player Control, Programming Cable Converter (or DBS Receiver) Control, or Programming Audio Control. 26 Page 26 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM CHANGING VOLUME LOCK The Millennium 4 is set to control volume of a component through your TV while in the TV,VCR, or Cable mode. However, in the Audio mode, you have separate control of of your audio component’s volume. If your TV is not remote controllable, or if you would like the volume to be controlled by a different component, you can change the Volume Lock setting to control a volume through a non-associated mode (e.g., through the cable in the TV mode). To Change Volume Lock to the Cable Mode: 1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. 2. Enter 9 - 9 - 3 and then press CBL once. The LED will blink twice. 3. Now, whenever you press VOL+, VOL-, or MUTE on the Millennium 4, volume will be controlled by your cable converter or DBS receiver. To Change Volume Lock to the TV Mode: 1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. 2. Enter 9 - 9 - 3 and then press TV once. The LED will blink twice. 3. Now, whenever you press VOL+, VOL-, or MUTE on the Millennium 4, volume will be controlled by your TV. To Change Volume Lock to the VCR Mode: 1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. 2. Enter 9 - 9 - 3 and then press VCR once. The LED will blink twice. 3. Now, whenever you press press VOL+, VOL-, or MUTE on the Millennium 4, volume will be controlled by your VCR or DVD player. continued on next page... 27 Page 27 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM CHANGING VOLUME LOCK ( continued) To Change Volume Lock to the Audio Mode: NOTE: Performing these steps will allow you to access the volume control of your audio component in all modes. 1. On the Millennium 4, press and hold SETUP until the LED blinks twice, then release SETUP. 2. Enter 9 - 9 - 3 and then press AUDIO once. The LED will blink twice. 3. Now, whenever you press press VOL+, VOL-, or MUTE on the Millennium 4, volume will be controlled by your audio component. 28 Page 28 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM TROUBLESHOOTING PROBLEM: LED does not blink when you press a key. SOLUTION: Replace the batteries with two (2) new AA alkaline batteries (see page 7). PROBLEM: LED blinks when you press a key, but home entertainment component does not respond. SOLUTION: Make sure you are aiming the Millennium 4 at your home entertainment component and that you are within 15 feet of the component you are trying to control. PROBLEM: The Millennium 4 does not control home entertainment components or commands are not performing properly. SOLUTION: Try all listed codes for the component brand being set up. Make sure all components can be operated with an infrared remote control. PROBLEM: TV/VCR combo does not respond properly. SOLUTION: Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation (see page 16). PROBLEM: No volume on a second TV. SOLUTION: Follow instructions in Changing Volume Lock (see page 27). PROBLEM: CH+ , CH - , and LAST do not work for your RCA TV. SOLUTION: Due to RCA design (1983-1987), only the original remote control will operate these functions. PROBLEM: Changing channels does not work properly. SOLUTION: If original remote control required pressing ENTER to change channels, press ENTER on the Millennium 4 after entering a channel number. PROBLEM: Tried “Search Method” and still could not find a working code. SOLUTION: Try the “Search Method” again after clearing out the device key as follows: Press and hold SETUP until the LED (red light) blinks twice, then release. Next enter 9 - 9 - 2. Then press and release the device key to be cleared twice. PROBLEM: Remote control does not turn on Sony or Sharp TV/VCR Combo. SOLUTION: For power on, these products require programming TV codes on the Millennium 4. For Sony, use TV code 0000 and VCR code 0032. For Sharp, use TV code 0093 and VCR code 0048. 29 Page 29 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM ADDITIONAL INFORMATION The Millennium 4 does not have any user-serviceable parts. Opening the case, except for the battery cover, may cause permanent damage to your Millennium 4. For help via the Internet, visit us at: cable.rcinfo.com (do not type in http:// or www before the address) For help via e-mail, contact us at: CableHelp@ueic.com Copyright 2003 by Universal Electronics Inc. No part of this publication may be reproduced, transmitted, transcribed, stored in any retrieval system, or translated to any language, in any form or by any means, electronic, mechanical, magnetic, optical, manual, or otherwise, without the prior written permission of Universal Electronics Inc. M4092A 01/03 30 Page 30 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 31 Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 32
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2003:01:22 09:38:42 Producer : Acrobat Distiller 4.0 for Macintosh Author : Roman Creator : QuarkXPressª: AdobePS 8.5.1 Title : Millennium 4 Mnl M4092 rev Modify Date : 2004:04:28 08:54:33-07:00 Page Count : 32EXIF Metadata provided by EXIF.tools