Millennium 4 Mnl M4092 Rev Logitech Universal Remote IRC600 Shaw TV User Guide

4 to the manual 2ed10421-db62-47e5-8309-d6b9f6886690

User Manual: Logitech Universal Remote IRC600

Open the PDF directly: View PDF .
Page Count: 32

MILLENNIUM™4

Universal Remote Control

User’s Guide

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 1

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Features And Functions . . . . . . . . . . . . . . . . . . . . . . 4

Key Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Programming TV Control . . . . . . . . . . . . . . . . . . . . . 8

Setup Codes for TVs . . . . . . . . . . . . . . . . . . . . . . . . 8

Programming VCR/DVD Player Control. . . . . . . . 12

Setup Codes for VCRs. . . . . . . . . . . . . . . . . . . . . . 13

Setup Codes for DVD Players. . . . . . . . . . . . . . . . . 15

Programming TV/VCR Combo Control . . . . . . . . 16

Setup Codes for TV/VCRs . . . . . . . . . . . . . . . . . . . 17

Programming Cable Converter

(or DBS Receiver) Control . . . . . . . . . . . . . . . . . . . 18

To Unlock the CBL Key. . . . . . . . . . . . . . . . . . . . . . 18

To Program the CBL Key . . . . . . . . . . . . . . . . . . . . 19

To Lock the CBL Key . . . . . . . . . . . . . . . . . . . . . . . 20

Setup Codes for Cable Converters. . . . . . . . . . . . . 20

Setup Codes for DBS Receivers. . . . . . . . . . . . . . . 20

Programming Channel Control Lock . . . . . . . . . . 21

To Activate Channel Control Lock . . . . . . . . . . . . . 21

To De-Activate Channel Control Lock. . . . . . . . . . . 21

Programming Audio Control . . . . . . . . . . . . . . . . . 22

Setup Codes for Audio Amplifiers . . . . . . . . . . . . . 22

Setup Codes for Audio Receivers. . . . . . . . . . . . . . 23

Searching For Your Code . . . . . . . . . . . . . . . . . . . . 24

Checking The Codes . . . . . . . . . . . . . . . . . . . . . . . 25

Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . 26

Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . 27

To Change Volume Lock to the Cable Mode . . . . . . 27

To Change Volume Lock to the TV Mode. . . . . . . . . 27

To Change Volume Lock to the VCR Mode . . . . . . . 27

To Change Volume Lock to the Audio Mode . . . . . . 28

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Additional Information . . . . . . . . . . . . . . . . . . . . . . 30

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 2

INTRODUCTION

The Universal Electronics Millennium™ 4 is our latest

generation universal remote control.It is designed with

sophisticated technology that will allow you to finally

consolidate the clutter of all of the original remote controls

in your home entertainment system.It’s packed with easy-

to-use features such as:

• Preprogrammed to operate the cable converter

supplied by your cable system provider

•Preprogrammed technology for easy setup

• Convenient hide-away sliding door to conceal

less-used functions

• Color-coded keys to quickly locate popular functions

• Cable ID Lock to lock your remote control for use only

with the cable converter

• Channel Lock to lock channel selection only to the

cable converter

• Code library for video and audio components

• Code Search to help program control of older or

discontinued components

Before you can use your new remote control,you will

need to program it to operate the specific home enter-

tainment components you wish to control. Follow the

instructions detailed in this manual to set up your

Millennium 4 and enjoy your new remote control.

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 3

FEATURES AND FUNCTIONS

Use the illustration below to locate Millennium 4 features

and then study the Key Charts (on the next two pages) to

learn how they function.

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 4

Key Charts

The LED (red light) blinks to show that

the remote control is working and is

sending signals.

Press AUDIO,VCR,TV,or CBL once

to select a home entertainment

component to control.

Press POWER once to turn on or off

the selected home entertainment

component.

Use SETUP for all programming

sequences.

Use the keypad (0~ 9) to directly select

channels (e.g.,09 or 31).

Press MUTE once to turn sound off

or on.

Press ENTER once after entering channel

numbers on some TV models.

Use VOL+ (or VOL-) to raise (or lower)

the sound volume.

Use CH+ (or CH-) to select the next

higher (or lower) channel.

Press LAST once to recall the last channel

and to page back one screen in the

main menu.

Use FAV to cycle through your favorite

channels that are stored in your cable

converter.

Use GUIDE to display the program guide.

Press PPV/LOCK once to display the pay

per view menu or to lock out a specific

channel on your cable converter.

Use EXIT to exit out of your cable

converter’s menu and guide.

continued on next page...

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 5

FEATURES AND FUNCTIONS

Key Charts (continued)

Use cursor keys to move the cursor in

the program guide and menu screens.

Use SELECT/OK to choose options, PPV

events,and to tune programs from the

program guide.

Use INFO to display current channel and

program information.

Press MENU once to display your cable

converter’s screen menu.

Use PAGE ▲▲(or PAGE ▼▼) to page up

or down) through menu screens and the

program guide.

Slide the door open to reveal less-often

used keys such as VCR transport buttons

and cable converter features.

In the VCR and TV modes, use the REW,

PLAY,FF,REC,STOP,and PAUSE keys to

control your VCR. To record a program,

press REC twice.

Reserved for cable converter features

(see your cable converter manual).

Press TV/VCR once to switch the VCR to

view TV channels or tape. This key will

also control the input select feature on

most TVs.

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 6

INSTALLING BATTERIES

1. On the back of the Millennium 4, push the tab

and lift off the battery cover.

2. Obtain two (2) fully-charged AA alkaline

batteries. Match the + and – marks on the

batteries to the + and – marks in the battery

case, then insert the new batteries.

3. Press the battery cover back into place. The tab

should click when the cover is locked.

4. Test the unit by pressing POWER and any mode

key (e.g. AUDIO,VCR,TV,or CBL). If the batteries

are inserted correctly, the LED will blink once.

NOTE: Whenever batteries need replacement, the Millennium 4

will blink twice with every key press. Simply replace the batteries

and the Millennium 4 will be restored to its full functionality,

complete with your favorite settings.

❶

❸

❷

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 7

PROGRAMMING TV CONTROL

NOTE: If you own a TV/VCR combination, skip this section and

perform “Programming TV/VCR Combo Control”on page 16.

Locate the brand name of your TV in the Setup Codes

for TVs in the next section, and write it in the space below.

TV Brand: __________________________________

The brands are listed in alphabetical order with the most

popular codes listed first.You will use one of these codes

to program the Millennium 4 to operate your TV:

1. Turn on the TV.

2. On the Millennium 4, press TV once. Press and

hold SETUP until the LED blinks twice, then

release SETUP.

3. Enter the first four-digit code for your TV. If

you perform this procedure correctly, the LED

will blink twice.

NOTE: If the LED did not blink twice after entering

the code’s last digit, then repeat steps 2 through 3 and

try entering the same code again.

4. Aim the Millennium 4 at your TV and press

POWER once.The TV should turn off.If it does

not, repeat steps 2 and 3, trying each code for

your brand until you find one that works. If it

still does not work, try searching for the code

(see Searching For Your Code on page 24).

5. For future reference, write your TV code in the

boxes below.

NOTE: Remember, to use the Millennium 4 to operate your TV,

press TV first.

Setup Codes for TVs:

AOC 0030, 0019

Admiral 0093, 0463

Aiko 0092

Akai 0030

Alaron 0179

America Action 0180

Anam 0180

Audiovox 0451, 0180, 0623, 0092

Baysonic 0180

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 8

Belcor 0019

Bell & Howell 0154, 0016

Bradford 0180

Brockwood 0019

Broksonic 0236, 0463

CXC 0180

Candle 0030, 0056

Carnivale 0030

Carver 0054

Celebrity 0000

Cineral 0451, 0092

Citizen 0060, 0030, 0056, 0092, 0280

Concerto 0056

Contec 0180

Craig 0180

Crosley 0054

Crown 0180

Curtis Mathes 0047, 0747, 0054, 0154, 0051,0451, 0093,0060, 0030,0056,

0145, 0016, 0166

Daewoo 0451, 0019, 0623, 0624, 0092

Daytron 0019

Denon 0145

Dumont 0017, 0019

Electroband 0000

Emerson 0154, 0236, 0463, 0180, 0178, 0179, 0019, 0623, 0624, 0282,

0280

Envision 0030

Fisher 0154

Fujitsu 0179, 0683

Funai 0180, 0179, 0171

Futuretech 0180

GE 0047, 0747, 0051, 0451, 0093, 0178, 0021, 0282

Gibralter 0017, 0030, 0019

GoldStar 0030, 0178, 0056, 0019

Gradiente 0053, 0056

Grunpy 0180, 0179

Hallmark 0178

Harley Davidson 0179

Harman/Kardon 0054

Harvard 0180

Hitachi 0056, 0145, 0016

Infinity 0054

Inteq 0017

JBL 0054

JCB 0000

JVC 0053

KEC 0180

KTV 0180, 0030, 0280

Kenwood 0030, 0019

Konka 0707, 0628, 0632, 0638, 0703

LG 0056

continued on next page...

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 9

PROGRAMMING TV CONTROL

Setup Codes for TVs (continued):

LXI 0047, 0747, 0054, 0154, 0156, 0178

Logik 0016

Luxman 0056

MGA 0150, 0030, 0178, 0019

MTC 0060, 0030, 0056, 0019

Magnavox 0054, 0030, 0179

Majestic 0016

Marantz 0054, 0030

Matsushita 0250

Megatron 0178, 0145

Memorex 0154, 0250, 0463, 0150, 0178, 0179, 0056, 0016

Midland 0047, 0747, 0017, 0051

Minutz 0021

Mitsubishi 0093, 0150, 0178, 0019

Motorola 0093

Multitech 0180

NAD 0156, 0178, 0166

NEC 0030, 0056, 0019

NTC 0092

Nikko 0030, 0178, 0092

Onwa 0180

Optimus 0154, 0250, 0166

Optonica 0093, 0165

Orion 0236, 0463, 0179

Panasonic 0051, 0250

Penney 0047, 0747, 0156, 0051, 0060, 0030, 0178, 0021, 0056, 0019

Philco 0054, 0463, 0030, 0145, 0019

Philips 0054

Pilot 0030, 0019

Pioneer 0166

Portland 0019, 0092

Prism 0051

Proscan 0047, 0747

Proton 0178

Pulsar 0017, 0019

Quasar 0051, 0250, 0165

RCA 0047, 0747, 0090, 0051, 0093, 0019, 0278

RadioShack 0047, 0747, 0154, 0180, 0030, 0178, 0056, 0019, 0165

Realistic 0154, 0180, 0030, 0178, 0056, 0019, 0165

Runco 0017, 0030

SSS 0180, 0019

Sampo 0030

Samsung 0060, 0030, 0178, 0056, 0019

Sansei 0451

Sansui 0463

Sanyo 0154

Scimitsu 0019

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 10

Scotch 0178

Scott 0236, 0180, 0178, 0179, 0019

Sears 0047, 0747, 0054, 0154, 0156, 0178, 0179, 0056, 0171

Semivox 0180

Semp 0156

Sharp 0093, 0688, 0165

Shogun 0019

Signature 0016

Sony 0000

Soundesign 0180, 0178, 0179

Squareview 0171

Starlite 0180

Supreme 0000

Sylvania 0054, 0030

Symphonic 0180, 0171

TMK 0178, 0056

TNCi 0017

Tandy 0093

Technics 0051, 0250

Technol Ace 0179

Techwood 0051, 0056

Teknika 0054, 0180, 0150, 0060, 0179, 0056, 0019, 0016, 0092

Telefunken 0056

Toshiba 0154, 0156, 0060

Vector Research 0030

Victor 0053

Vidikron 0054

Vidtech 0178, 0019

Wards 0054, 0030, 0178, 0021, 0179, 0056, 0019, 0016, 0165

White Westinghouse 0463, 0623,0624

Yamaha 0030, 0019

Zenith 0017, 0463, 0624, 0016, 0092

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 11

PROGRAMMING VCR/DVD PLAYER CONTROL

NOTE: If you own a TV/VCR combination, skip this section and

perform “Programming TV/VCR Combo Control”on page 16.

Locate the brand name of your VCR in Setup Codes for

VCRs on the next page,or your DVD player in Setup Codes

for DVD Players on page 15,and write it in the appropriate

space below.

VCR Brand: ________________________________

DVD Player Brand: ____________________________

The brands are listed in alphabetical order with the most

popular codes listed first.You will use one of these codes

to program the Millennium 4 to operate your VCR or

DVD player:

1. Turn on your VCR and insert a video cassette,

or turn on your DVD player and insert a DVD.

2. On the Millennium 4, press VCR once. Press

and hold SETUP until the LED blinks twice,

then release SETUP.

3. Enter the first four-digit code for your VCR or

DVD player. If you perform this procedure

correctly, the LED will blink twice.

NOTE: If the LED did not blink twice after entering

the code’s last digit, then repeat steps 2 through 3 and

try entering the same code again.

4. Aim the Millennium 4 at the VCR or DVD

player and press POWER once. The device

should turn off.If your VCR remote control

does not have a POWER key, press PLAY.Ifthe

VCR does not respond, repeat steps 2 and 3,

trying each code listed for your brand until you

find one that works. If the device still does not

work , try searching for the code (see Searching

For Your Code on page 24).

5. For future reference, write your device’s code

and type in the boxes and space below.

Device Type:________________________

NOTE: Remember, to use the Millennium 4 to operate your VCR

or DVD player, press VCR first.

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 12

Setup Codes for VCRs:

Admiral 0048, 0209

Adventura 0000

Aiko 0278

Aiwa 0037, 0000

Akai 0041

America Action 0278

American High 0035

Asha 0240

Audiovox 0037

Beaumark 0240

Bell & Howell 0104

Broksonic 0184, 0121, 0209, 0002, 0479, 0295

CCE 0072, 0278

Calix 0037

Canon 0035

Carver 0081

Cineral 0278

Citizen 0037, 0278

Colt 0072

Craig 0037, 0047, 0240, 0072

Curtis Mathes 0035, 0060, 0162, 0041

Cybernex 0240

Daewoo 0045, 0278, 0561

Denon 0042

Dynatech 0000

Electrohome 0037

Electrophonic 0037

Emerex 0032

Emerson 0037, 0184, 0000, 0121, 0043, 0209, 0002, 0278, 0479, 0561,

0295, 0294

Fisher 0047, 0104

Fuji 0035, 0033

Funai 0000

GE 0035, 0060, 0048, 0240

Garrard 0000

Go Video 0432, 0526,0643, 0232, 0279

GoldStar 0037

Gradiente 0000

HI-Q 0047

Harley Davidson 0000

Harman/Kardon 0081

Harwood 0072

Headquarter 0046

Hitachi 0000, 0042, 0041, 0105

Hughes Network Sys. 0042

JVC 0067, 0041

Jensen 0041

KEC 0037, 0278

KLH 0072

continued on next page...

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 13

PROGRAMMING VCR/DVD PLAYER CONTROL

Setup Codes for VCRs (continued):

Kenwood 0067, 0041

Kodak 0035, 0037

LXI 0037

Lloyd’s 0000

Logik 0072

MEI 0035

MGA 0240, 0043

MGN Technology 0240

MTC 0000, 0240

Magnasonic 0278

Magnavox 0035, 0039, 0081, 0000

Magnin 0240

Marantz 0035, 0081

Marta 0037

Matsushita 0035, 0162, 0454

Memorex 0035, 0037, 0048, 0039, 0047, 0162, 0000, 0240, 0104, 0209,

0454, 0479, 0046

Minolta 0042, 0105

Mitsubishi 0048, 0067, 0043

Motorola 0035, 0048

Multitech 0000, 0072

NEC 0067, 0104, 0041

Nikko 0037

Noblex 0240

Olympus 0035

Optimus 0037, 0048, 0162, 0104, 0454, 0432

Orion 0184, 0209, 0002, 0479, 0295

Panasonic 0035, 0225, 0162, 0454, 0616

Penney 0035, 0037, 0042, 0240

Pentax 0042, 0105

Philco 0035, 0209, 0479

Philips 0035, 0081, 0618

Pilot 0037

Pioneer 0067

Polk Audio 0081

Profitronic 0240

Proscan 0060

Protec 0072

Pulsar 0039

Quarter 0046

Quartz 0046

Quasar 0035, 0162, 0454

RCA 0035, 0060, 0048, 0042, 0240, 0105, 0060

RadioShack 0000

Radix 0037

Randex 0037

Realistic 0035, 0037, 0048, 0047, 0000, 0104, 0046

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 14

ReplayTV 0614, 0616

Runco 0039

STS 0042

Samsung 0045, 0240

Samtron 0643

Sanky 0048, 0039

Sansui 0000, 0067, 0209, 0041, 0479

Sanyo 0047, 0240, 0104, 0046

Scott 0184, 0045, 0121, 0043

Sears 0035, 0037, 0047, 0000, 0042, 0104, 0046, 0105

Semp 0045

Sharp 0048

Shintom 0072

Shogun 0240

Singer 0072

Sony 0035, 0032, 0000, 0636, 0033

Sylvania 0035, 0081, 0000, 0043

Symphonic 0000

TMK 0240

Tatung 0041

Teac 0000, 0041

Technics 0035, 0162

Teknika 0035, 0037, 0000

Thomas 0000

Tivo 0618, 0636

Toshiba 0045, 0043

Totevision 0037, 0240

Unitech 0240

Vector 0045

Video Concepts 0045

Videosonic 0240

Wards 0035, 0060, 0048, 0047, 0081, 0000, 0042, 0240, 0072

White Westinghouse 0209, 0072,0278

XR-1000 0035, 0000, 0072

Zenith 0039, 0000, 0209, 0479, 0033

Setup Codes for DVD Players:

Aiwa 0641

Apex 0672

B & K 0655, 0662

Denon 0490, 0634

Fisher 0670

GE 0522

Gradiente 0651

Harman/Kardon 0582

Hitachi 0573, 0664

Hiteker 0672

JVC 0558, 0623

Kenwood 0534, 0682

continued on next page...

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 15

PROGRAMMING VCR/DVD PLAYER CONTROL

Setup Codes for DVD Players (continued):

Konka 0711, 0719, 0720, 0721

Magnavox 0503, 0675

Marantz 0539

Mitsubishi 0521

Onkyo 0503, 0627

Optimus 0571

Oritron 0651

Panasonic 0490, 0677, 0632, 0678, 0679

Philips 0503, 0539

Pioneer 0525, 0571, 0632

Proscan 0522

RCA 0522, 0571

Samsung 0573

Sharp 0630

Sherwood 0633

Sony 0533

Technics 0490

Techwood 0692

Theta Digital 0571

Toshiba 0503

Yamaha 0490, 0545

Zenith 0503, 0591

PROGRAMMING TV/VCR COMBO CONTROL

Locate the brand name of your TV/VCR Combo in Setup

Codes for TV/VCR Combos on the next page,and write it in

the space below.

TV/VCR Combo Brand: ________________________

The brands are listed in alphabetical order with popular

codes listed first.You will use one of these codes to pro-

gram the Millennium 4 to operate your TV/VCR Combo:

1. Turn on your TV/VCR Combo and insert a

video cassette.

2. On the Millennium 4, press VCR once. Press

and hold SETUP until the LED blinks twice,

then release SETUP.

3. Enter the first four-digit code for your TV/VCR

Combo. If you perform this procedure correctly,

the LED will blink twice.

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 16

NOTE: If the LED did not blink twice after entering

the code’s last digit, then repeat steps 2 through 3 and

try entering the same code again.

4. Aim the Millennium 4 at your TV/VCR Combo

and press POWER once.The unit should turn

off.If it does not respond, repeat steps 2 and 3,

trying each code listed for your brand until you

find one that works. If it still does not work, try

searching for the code (see Searching For Your

Code on page 24).

5. If you’ve found a TV/VCR setup code that works

your TV/VCR Combo and a separate TV code is

also listed, you’ll need to program this code into

the Millennium 4 to access volume control (see

Programming TV Control on page 8).

If there is no separate TV code listed, you will

need to perform the following steps to access

volume control:

a. Press and hold SETUP until the LED blinks

twice, then release SETUP.

b. Enter 9 - 9 - 3. The LED will blink twice.

c. Press VCR once. The LED will blink twice.

6. For future reference, write your TV/VCR

Combo code in the boxes below.

NOTE: Remember, to use the Millennium 4 to operate your

TV/VCR Combo, press VCR first.

Setup Codes for TV/VCR Combos:

American High 0035 (for TV use 0051)

Brocksonic 0002, 0294,

Colt 0072

Curtis Mathis 0035 (for TV use 0051)

Daewoo 0278

Emerson 0002, 0294, 0479

Funai 0000

GE 0035 (for TV use 0051),0060 (for TV use 0047),

0048 (for TV use 0093), 0240

Hitachi 0035 (for TV use 0051), 0000

HQ 0000

Lloyds 0000

MGA 0240

Magnavox 0081 (for TV use 0054), 0035 (for TV use 0051), 0000

continued on next page...

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 17

PROGRAMMING TV/VCR COMBO CONTROL

Setup Codes for TV/VCR Combos (continued):

Magnin 0240

Memorex 0037, 0162 (for TV use 0250)

Mitsubishi 0048 (for TV use 0093)

Orion 0002, 0294, 0479

Panasonic 0035 (for TV use 0051), 0162 (for TV use 0250)

Penney 0035 (for TV use 0051), 0240, 0162 (for TV use 0250)

Quasar 0035 (for TV use 0051), 0162 (for TV use 0250)

RCA 0060 (for TV use 0047), 0035 (for TV use 0051),

0048 (for TV use 0093)

Sansui 0000, 0479

Sanyo 0240

Sears 0000, 0037

Sharp 0048 (for TV use 0093)

Sony 0032 (for TV use 0000)

Symphonic 0000

Zenith 0000

PROGRAMMING CABLE CONVERTER

(OR DBS RECEIVER) CONTROL

The Millennium 4 is preprogrammed at the factory to

operate the cable converter given to you by your cable

company. However, if you have another brand or model

of cable converter or satellite receiver that you would like

to control, then you’ll need to perform the following

instructions to unlock the cable key, enter in a new code,

and lock the cable key again.

To Unlock the CBL Key:

1. Turn on the Cable Converter or DBS Receiver.

2. On the Millennium 4, press CBL once. Press

and hold SETUP until the LED blinks twice,

then release SETUP.

3. Enter 9- 9 - 7. The LED will blink twice.

4. Press CH- once. The LED will blink twice.

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 18

To Program the CBL Key:

1. On the next page,locate the brand name of

your Cable Converter in Setup Codes For Cable

Converters, or DBS (Direct Broadcast Satellite)

Receiver in Setup Codes For DBS Receivers,and

write it in the appropriate space below.

Cable Converter Brand: ________________

DBS Receiver Brand: __________________

The brands are listed in alphabetical order

with the most popular codes listed first.You

will use one of these codes to reprogram the

Millennium 4 to operate your Cable Converter

or DBS Receiver.

2. On the Millennium 4, press CBL once. Press

and hold SETUP until the LED blinks twice,

then release SETUP.

3. Enter the first four-digit code for your Cable

Converter or DBS Receiver. If you perform this

procedure correctly, the LED will blink twice.

NOTE: If the LED did not blink twice after entering

the code’s last digit, then repeat steps 2 through 3 and

try entering the same code again.

4. Aim the Millennium 4 at your Cable Converter

or DBS Receiver and press POWER once. The

unit should turn off. If it does not respond,

repeat steps 2 and 3,trying each code listed for

your brand until you find one that works. If it

still does not work , try searching for the code

(see Searching For Your Code on page 24).

5. For future reference, write your device’s code

and type in the boxes and space below.

Device Type:________________________

NOTE: Remember, to use the Millennium 4 to operate your Cable

Converter or DBS Receiver, press CBL first.

continued on next page...

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 19

PROGRAMMING CABLE CONVERTER

(OR DBS RECEIVER) CONTROL

(continued)

To Lock the CBL Key:

1. On the Millennium 4, press CBL once. Press

and hold SETUP until the LED blinks twice,

then release SETUP.

2. Enter 9- 9 - 7. The LED will blink twice.

3. Press CH+ once. The LED will blink twice.

Setup Codes for Cable Converters:

ABC 0003, 0008

Americast 0899

Bell South 0899

General Instrument 0476

GoldStar 0144

Hamlin 0273

Jerrold 0003, 0476

Memorex 0000

Panasonic 0000

Paragon 0000

Philips 0305

Pioneer 0144, 0877, 0533

Pioneer 0533

Pulsar 0000

Quasar 0000

Regal 0273

Runco 0000

Samsung 0144

Scientific Atlanta 0008,0477, 0877

Starcom 0003

Toshiba 0000

Zenith 0525, 0000, 0899

Setup Codes for DBS Receivers:

Echostar 0775, 1005

Expressvu 0775

GE 0566

General Instrument 0869, 0892

HTS 0775

Hughes Network Sys. 0749

JVC 0775

Mitsubishi 0749

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 20

Next Level 0869, 0892

Philips 0749, 1076

Proscan 0392

RCA 0566, 0392

RadioShack 0869

Samsung 1109

Sony 0639

Star Choice 0869

Toshiba 0749

PROGRAMMING CHANNEL CONTROL LOCK

By activating this feature,the Millennium 4 will only

allow access to the channel control capabilities of your

cable converter. This will guarantee that you do not

inadvertently change the channel on your TV or VCR.

To Activate Channel Control Lock:

1. On the Millennium 4, press and hold SETUP

until the LED blinks twice, then release SETUP.

2. Enter 9- 9 - 6. The LED will blink twice.

3. Press CH+ once. The LED will blink twice.

4. Now, regardless of what mode you select (i.e.,

TV,VCR,or CBL), only the channel control capa-

bility of your cable converter will be accessible.

NOTE: This feature does not affect the Audio mode.

To De-Activate Channel Control Lock:

1. On the Millennium 4, press and hold SETUP

until the LED blinks twice, then release SETUP.

2. Enter 9- 9 - 6. The LED will blink twice.

3. Press CH- once. The LED will blink twice.

4. The Millennium 4 will again provide TV and

VCR channel control capabilities while in the

TV or VCR mode.

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 21

PROGRAMMING AUDIO CONTROL

Locate the brand name of your audio amplifier or receiver

in one of the accompanying code lists at the end of this

section.Write it in the appropriate space below.

Audio Amplifier Brand: ________________________

Audio Receiver Brand:__________________________

The brands are listed in alphabetical order with popular

codes listed first.You will use one of these codes to

program the Millennium 4 to operate your audio device:

1. Turn on the audio device.

2. On the Millennium 4, press AUDIO once. Press

and hold SETUP until the LED blinks twice,

then release SETUP.

3. Enter the first four-digit code for your audio

device.If you perform this procedure correctly,

the LED will blink twice.

NOTE: If the LED did not blink twice after entering

the code’s last digit, then repeat steps 2 through 3 and

try entering the same code again.

4. Aim the Millennium 4 at your audio device and

press POWER once.The unit should turn off.If

it does not respond, repeat steps 2 and 3, trying

each code listed for your brand until you find

one that works. If it still does not work , try

searching for the code (see Searching For Your

Code on page 24).

5. For future reference, write your device’s code

and type in the boxes and space below.

NOTE: Remember, to use the Millennium 4 to operate your audio

device, press AUDIO first.

Setup Codes for Audio Amplifiers:

Denon 0160

GE 0078

Harman/Kardon 0892

JVC 0331

Marantz 0892

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 22

Optimus 0395

Panasonic 0308

Philips 0892

Polk Audio 0892

Realistic 0395

Sony 0689

Soundesign 0078

Technics 0308

Victor 0331

Wards 0078

Yamaha 0354

Setup Codes for Audio Receivers:

ADC 0531

Adcom 0616

Aiwa 1405, 0121, 0405

Capetronic 0531

Carver 0008

Casio 0195

Clarinette 0195

Denon 1104, 1160

Garrard 0463

Harman/Kardon 0110, 0891

JBL 0110

JVC 0074

Kenwood 1313, 1027, 1570, 1569, 0186, 0077

Lloyd’s 0195

MCS 0039, 0346

Magnavox 0531, 0195, 0391

Marantz 0039

Modulaire 0195

Nakamichi 0097

Onkyo 0135

Optimus 1023, 0531, 0670, 0186, 0177

Panasonic 1518, 0039

Penney 0195

Philips 1269,1120, 0391

Pioneer 1023, 0531, 0014, 0150, 0630

Proscan 1254

Quasar 0039

RCA 1023, 1254, 0531, 0054, 0346

Realistic 0195

Sansui 0346

Sharp 0186

Sony 1058

Soundesign 0670

Sunfire 1313

Teac 0463

Technics 1308, 1309, 1518, 0039

continued on next page...

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 23

PROGRAMMING AUDIO CONTROL

Setup Codes for Audio Amplifiers (continued):

Victor 0074

Wards 0014, 0054

Yamaha 0176, 1176, 0186

Yorx 0195

Zenith 0857

SEARCHING FOR YOUR CODE

If your TV,VCR or DVD Player, Cable Converter, or Audio

Component does not respond to the Millennium 4 after

trying all of the codes listed for your brand, or if your

brand is not listed at all, try searching for your code.

For example, to search for a code for your TV:

1. Turn on your TV.

2. On the Millennium 4, press and hold SETUP

until the LED blinks twice, then release SETUP.

3. Enter 9- 9 - 1. The LED will blink twice.

4. Aim the remote control at the the TV and slowly

alternate between pressing POWER and TV.

Stop when the TV turns off.

NOTE: In the search mode, the Millennium 4 will

send IR codes from its library to the selected compo-

nent, starting with the most popular code first.

5. Press SETUP once to lock in the code.

6. To search for the codes of your other

components,repeat steps 1 through 5, but

substitute the appropriate key (i.e., VCR,CBL,

or AUDIO) for the (VCR or DVD, Cable, or

Audio) component you are searching for.

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 24

CHECKING THE CODES

If you have set up the Millennium 4 using the Searching

For Your Code procedure,you may need to find out which

four-digit code is operating your equipment:

For example, to find out which code is operating your TV:

1. Turn on your TV.

2. On the Millennium 4, press and hold SETUP

until the LED blinks twice, then release SETUP.

3. Enter 9- 9 - 0. The LED will blink twice.

4. To view the code for the first digit, press 1once.

Wait 3 seconds and count the number of LED

blinks (e.g., 3 blinks = 3) and write down the

number in the leftmost TV Code box below.

NOTE: If a code digit is “0”, the LED will not blink.

5. Repeat step 4 three more times for remaining

digits. Use 2 for the second digit, 3for the third

digit, and 4for the fourth digit. Finish writing

down the code in the TV Code boxes below.

6. To check for the codes of your other

components,repeat steps 1 through 5, but

substitute the appropriate key (i.e., VCR,CBL,

or AUDIO) for the (VCR or DVD, Cable, or

Audio) component you are checking.Write

down the codes in the appropriate boxes below.

TV Code

VCR (or DVD Player) Code

CBL Code

AUDIO ___________________ Code

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 25

RE-ASSIGNING DEVICE KEYS

The Millennium 4 can be set up to control a second TV

or VCR, or any combination of four home entertainment

components. For example, to have the Millennium 4

control a TV, a Cable Converter, and two VCRs, you will

need to re-assign the unused AUDIO key to operate the

second VCR as follows:

1. On the Millennium 4, press and hold SETUP

until the LED blinks twice, then release SETUP.

2. Enter 9- 9 - 2. The LED will blink twice.

3. Press VCR once, then press AUDIO once.

4. The AUDIO key is now ready to be programmed

for your second VCR. See Programming

VCR/DVD Player Control on page 12.

To re-assign other device keys, repeat steps 1 through 4 by

substituting the key sequence from the following chart for

a desired component:

To Re-Assign Perform Key Sequence

TV as 2nd VCR key: SETUP - 9 - 9 - 2- VCR - TV

TV as 2nd Audio key: SETUP - 9 - 9 - 2- AUDIO - TV

TV as 2nd Cable key: SETUP - 9 - 9 - 2- CBL - TV

TV back to TV:SETUP - 9 - 9 - 2- TV - TV

VCR as 2nd TV key: SETUP - 9 - 9 - 2- TV - VCR

VCR as 2nd Audio key: SETUP - 9 - 9 - 2- AUDIO - VCR

VCR as 2nd Cable key: SETUP - 9 - 9 - 2- CBL - VCR

VCR back to VCR:SETUP - 9 - 9 - 2- VCR - VCR

AUDIO as 2nd TV key: SETUP - 9 - 9 - 2- TV - AUDIO

AUDIO as 2nd VCR key: SETUP - 9 - 9 - 2- VCR - AUDIO

AUDIO

as 2nd Cable key:

SETUP - 9 - 9 - 2- CBL - AUDIO

AUDIO

back to

AUDIO

SETUP - 9 - 9 - 2- AUDIO - AUDIO

Upon completion of a re-assignment, the LED will blink

twice to confirm your selection.At that time, you will also

need to program the Millennium 4 to control the new

component. See previous sections on Programming TV

Control,Programming VCR/DVD Player Control,

Programming Cable Converter (or DBS Receiver) Control,

or Programming Audio Control.

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 26

CHANGING VOLUME LOCK

The Millennium 4 is set to control volume of a component

through your TV while in the TV,VCR, or Cable mode.

However, in the Audio mode, you have separate control of

of your audio component’s volume.

If your TV is not remote controllable, or if you would like

the volume to be controlled by a different component, you

can change the Volume Lock setting to control a volume

through a non-associated mode (e.g., through the cable in

the TV mode).

To Change Volume Lock to the Cable Mode:

1. On the Millennium 4, press and hold SETUP

until the LED blinks twice, then release SETUP.

2. Enter 9- 9 - 3and then press CBL once. The

LED will blink twice.

3. Now, whenever you press VOL+,VOL-,or MUTE

on the Millennium 4, volume will be controlled

by your cable converter or DBS receiver.

To Change Volume Lock to the TV Mode:

1. On the Millennium 4, press and hold SETUP

until the LED blinks twice, then release SETUP.

2. Enter 9- 9 - 3and then press TV once. The

LED will blink twice.

3. Now, whenever you press VOL+,VOL-,or MUTE

on the Millennium 4, volume will be controlled

by your TV.

To Change Volume Lock to the VCR Mode:

1. On the Millennium 4, press and hold SETUP

until the LED blinks twice, then release SETUP.

2. Enter 9- 9 - 3and then press VCR once. The

LED will blink twice.

3. Now, whenever you press press VOL+,VOL-,or

MUTE on the Millennium 4, volume will be

controlled by your VCR or DVD player.

continued on next page...

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 27

CHANGING VOLUME LOCK ( continued)

To Change Volume Lock to the Audio Mode:

NOTE: Performing these steps will allow you to access the volume

control of your audio component in all modes.

1. On the Millennium 4, press and hold SETUP

until the LED blinks twice, then release SETUP.

2. Enter 9- 9 - 3and then press AUDIO once. The

LED will blink twice.

3. Now, whenever you press press VOL+,VOL-,or

MUTE on the Millennium 4, volume will be

controlled by your audio component.

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 28

TROUBLESHOOTING

PROBLEM: LED does not blink when you press a key.

SOLUTION: Replace the batteries with two (2) new AA

alkaline batteries (see page 7).

PROBLEM: LED blinks when you press a key, but home

entertainment component does not respond.

SOLUTION: Make sure you are aiming the Millennium 4 at

your home entertainment component and that

you are within 15 feet of the component you are

trying to control.

PROBLEM: The Millennium 4 does not control home

entertainment components or commands are

not performing properly.

SOLUTION: Try all listed codes for the component brand

being set up. Make sure all components can be

operated with an infrared remote control.

PROBLEM: TV/VCR combo does not respond properly.

SOLUTION: Use the VCR codes for your brand. Some combo

units may require both a TV code and a VCR

code for full operation (see page 16).

PROBLEM: No volume on a second TV.

SOLUTION: Follow instructions in Changing Volume Lock

(see page 27).

PROBLEM: CH+ ,CH - ,and LAST do not work for your

RCA TV.

SOLUTION: Due to RCA design (1983-1987), only the original

remote control will operate these functions.

PROBLEM: Changing channels does not work properly.

SOLUTION: If original remote control required pressing

ENTER to change channels, press ENTER on the

Millennium 4 after entering a channel number.

PROBLEM: Tried “Search Method” and still could not find a

working code.

SOLUTION: Try the “Search Method”again after clearing out

the device key as follows: Press and hold SETUP

until the LED (red light) blinks twice,then

release.Next enter 9- 9- 2. Then press and

release the device key to be cleared twice.

PROBLEM: Remote control does not turn on Sony or Sharp

TV/VCR Combo.

SOLUTION: For power on, these products require program-

ming TV codes on the Millennium 4. For Sony,

use TV code 0000 and VCR code 0032. For Sharp,

use TV code 0093 and VCR code 0048.

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 29

ADDITIONAL INFORMATION

The Millennium 4 does not have any user-serviceable

parts. Opening the case, except for the battery cover, may

cause permanent damage to your Millennium 4.

For help via the Internet, visit us at:

cable.rcinfo.com

(do not type in http:// or www before the address)

For help via e-mail, contact us at:

CableHelp@ueic.com

of this publication may be reproduced,transmitted,

transcribed, stored in any retrieval system, or translated

to any language, in any form or by any means, electronic,

mechanical, magnetic, optical, manual, or otherwise,

without the prior written permission of Universal

Electronics Inc.

M4092A 01/03

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 30

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 31

Millennium 4 Mnl M4092 rev 1/22/03 9:38 AM Page 32

Millennium 4 Mnl M4092 Rev Logitech Universal Remote IRC600 Shaw TV User Guide

4 to the manual 2ed10421-db62-47e5-8309-d6b9f6886690

Navigation menu

Versions of this User Manual:

Views

Navigation