Shimano PCE1 Di2 PC Linkage User Manual
User Manual: Shimano PCE1 Di2 PC Linkage User Manual
Open the PDF directly: View PDF .
Page Count: 10
Download | |
Open PDF In Browser | View PDF |
9070 series Around cockpit area SW-R610 Remote sprinter shifter Junction for cockpit area 3 port ST-9070 SW-9071 Remote TT/Time trial shifter New 1 button design Dual control lever SW-R671 SM-EW90-F Dual control lever SM-AD90 Band adapter Electric wire for external wire routing 2 pcs 11-speed HG CS 11-23T 11-25T 11-28T 12-25T 12-28T Heart rate monitor SM-BB9000 BB unit SM-BB92-41B Press - Fit type BB SM-BMR2-L/S/I SM-BCC1 Battery charger Cord for SM-BCR1 Battery cage adapter Electric wire for built-in type wire routing Built-in wire routing SM-JC41 Junction Built-in type SM-BTR2 Battery Built-in type SM-BCR2 Cord cover Battery charger for SM-BTR2 SM-SPD1 Speed sensor Caliper brake Direct mount WH-9000-C75-TU 75mm deep Carbon Tubular Wheel set WH-9000-C50-TU 50mm deep Carbon Tubular Wheel set CN-9000 BR-9010-F Direct mount caliper brake / Front FC-9000 HOLLOWTECH-II W/BB cup unit 50-34T 53-39T 52-36T 54-42T 52-38T 55-42T SM-BCR1 Battery SM-BA01 SM-EWC2 SM-HRR1 SM-BTR1 Battery mount EW-SD50-I 4pcs for SM-JC40/41 BR-9000 CS-9000 Junction WH-9000-C50-CL WH-9000-C35-TU 35mm deep Carbon Tubular Wheel set WH-9000-C24-TL Carbon/Aluminum Road Tubeless Wheel set WH-9000-C35-CL 35mm deep Carbon/Aluminum Clincher Wheel set 50mm deep Carbon/Aluminum Clincher Wheel set WH-9000-C24-CL Carbon/Aluminum Clincher Wheel set PD-9000 SPD-SL Pedal BR-9010-R Direct mount caliper brake / Rear SM-CB90 Cable adjuster for BR-9010 HB-9000 FH-9000 CP-W020 (10-speed) CP-W024 (10-speed) CP-WH23 CP-W184 Spoke protector BC-9000 Brake cable 1 Line-up Chart Version 1.4 All information on this page as of Apr. 27th 2012. ST-9071 Junction for cockpit area with wireless unit 5 port Super narrow HG chain for 11-speed FD-9070-F EW-SD50 Junction for cockpit area with wireless unit 5 port SM-EW90-F SM-JC40 Electric wire for external wire routing Cycle computer Wireless type SW-R600 RD-9070-SS EW-SD50 SC-R770 Remote Triathlon shifter Current 2 button design Remote satellite shifter (Climbing shifter) External wire routing SM-EW90-A TT/TRI spec (2×11-speed) ,0*BSVG Electric wire routing < DURA-ACE 9070 series > Built-in battery mount type (Internal wire routing) Connector Hole Junction (SM-JC41) External battery mount type (Internal wire routing) Connector Hole Junction (SM-JC41) External battery mount type (External wire routing) Connector Junction (SM-JC40) 20 All information on this page as of Apr. 27th 2012. Junction (SM-JC40) ,0*BSVG Electric wire routing around cockpit area Technical Information 1. Drop handle type 1-1. 3 port type ST-9070 Port for remote sprinter shifter ST-9070 E-tube port ×2 SW-R610 option E-tube port ×2 SM-EW90-A Junction-A SM-JC40/41 SW-R600 Junction-B option E-tube port ×3 E-tube connector Connector for remote sprinter shifter 22 All information on this page as of Apr. 27th 2012. Version 1.4 Port for remote sprinter shifter SW-R610 option 1-2. 5 port with wireless unit type SW-R671 option Technical Information SW-9071 option or ST-9070 ST-9070 Port for remote sprinter shifter SW-R610 option E-tube port ×2 SC-R770 E-tube port ×2 SM-EW90-F Junction-A SM-JC40/41 SW-R600 Junction-B option Port for remote sprinter shifter SW-R610 option E-tube port ×5 E-tube connector Connector for remote sprinter shifter Wireless All information on this page as of Apr. 27th 2012. Version 1.4 23 2. TT / Triathlon handle type Technical Information 2-1. 5 port with wireless unit type SW-9071 option SW-R671 option or 6 18 ST-9071 ST-9071 SC-R770 SM-EW90-F Junction-A SM-JC40/41 Junction-B E-tube port ×5 E-tube connector Connector for remote sprinter shifter Wireless 24 All information on this page as of Apr. 27th 2012. Version 1.4 2. Battery holder and junction Technical Information Short size Battery Holder SM-BMR2-S (External wire routing) Long size Battery Holder SM-BMR2-I (Internal wire routing) Long size Battery Holder 13 30 SM-BMR2-L (External wire routing) Junction SM-JC40 (External mount type) 14.3 Junction SM-JC41 (Built in type) 30 53.6 8 All information on this page as of Apr. 27th 2012. Version 1.4 7 PC Linkage SM-PCE1 1 SM -P CE 1 2 2 ITEM NO. 1 2 SHIMANO CODE NO. Y7EA02000 Y7EA03000 DESCRIPTION USB Cable PC Link Cable Feb.-2011-3138 © Shimano Inc. I Specifications are subject to change without notice. SI-7EA0A-002-00 Technical Service Instructions SI-7EA0A-002 SM-PCE1 NOTE 2. Click the [Next] button. Compatible PCs Operating system Windows XP 32bit/64bit (SP2 or higher) Windows Vista 32bit/64bit Windows 7 32bit/64bit Required components .NET Framework 3.5 Other hardware USB 1.1/2.0 Active Internet connection Display resolution: XGA (1024 x 768 dots) or higher (as of 1 November 2010) • Do not use outdoors or in environments with high humidity. • Do not place the SM-PCE1 on dusty floors when using it. • Place the SM-PCE1 on a stable surface such as a table when using it. • Do not place any objects on top of the SM-PCE1 or its cables. • Do not wrap the cables into bundles. • Do not hold the SM-PCE1 by the cables when carrying it. • Do not apply excessive tension to the cables. • Do not use any USB cable other than the USB cable which is supplied with the SM-PCE1. • Connect the SM-PCE1 directly to a computer, without using an intermediate device such as a USB hub. • Do not ride the bicycle while the SM-PCE1 and cable are still connected to it. • Do not connect two or more of the same units to the same connection point. If this is not done, the units may not operate correctly. • Do not connect or disconnect units again while unit recognition is in progress or after recognition is complete. If this is not done, the units may not operate correctly. Check the procedures which are given in the user's manual for the PC application when connecting and disconnecting units. • After connecting the battery and launching the PC application, be sure to disconnect the SM-PCE1 from the bicycle and then disconnect and reconnect the battery. If this is not done, the system may not operate correctly. • The tightness of the PC link cable will tend to drop after repeated connections and disconnections. If this happens, replace the cable. • Do not wash the SM-PCE1 or wipe it using detergents. • Do not connect two or more SM-PCE1 units to the same PC at the same time. If two or more SM-PCE1 units are connected, they will not operate correctly. In addition, operating errors may occur at the PC and it may require the PC to be restarted. When the PC application is run, a “Connect the SM-PCE1.” message will be displayed, so connect the USB cable of the SM-PCE1 to the PC. 3. If you agree to the terms of the Software License Agreement, click the [Yes] button. The SM-PCE1 can be used to connect a PC to the bicycle (system or unit), and a PC application (such as Shimano STEPS Manager) can be used to carry out tasks such as problem diagnosis of single units and the whole system, updating firmware*, and retrieving logs. For details on operating the PC, refer to the manual for the PC application. * Firmware: the software inside each unit Flow of operation when using the SM-PCE1 for the first time After purchasing the SM-PCE1, follow this procedure to prepare the SM-PCE1 for use. Download the PC application from the website. 4. If you would like Shimano STEPS Manager to be available for use by all users of the PC, select “Anyone who uses this computer (all users)”. If you would like only the current user of the PC to be able to use the application, select “Only for me”. After making the selection, click the [Next] button. 5. Select the installation folder and then click the [Next] button. Install the USB driver. • For details, refer to the manual for the PC application. • The method for displaying the manual for Shimano STEPS Manager is given in “Displaying the manual for Shimano STEPS Manager”. 5. Connect the SM-PCE1 to the system or to a unit. 6. Installation will begin when you 1. Downloading the PC application The PC application can be obtained by downloading it from http://media.shimano.com. You will need the following user ID and password at this time. • User ID: shimano – 20 °C -- 70 °C Operating/ storage humidity 10 -- 95 % RH/ 10 -- 95 % RH Rated voltage 5V±5% Rated power 2.5 W Interface USB 2.0 (Full Speed) Port type At PC: A type At SM-PCE1: Mini B type Dimensions 96.4 x 53.4 x 22 mm Weight 80 g LED During normal operation: Illuminated During charging: Flashing Accessories: * PC link cable (x 2) 2 m * USB cable (x 1) 50 cm • Password: 2s8m8n3 2. Installing the PC application After downloading the PC application, run the Installer to install it to the PC by the following procedure. (The screenshots below show examples of installing Shimano STEPS Manager to a PC which is running Windows XP.) 1. Run the Installer. Select the language in the window which appears, and then click [OK]. If the same problem occurs even after repeatedly disconnecting and reconnecting the USB cable, contact the place of purchase or the nearest bicycle manufacturer in the country of use. click the [Install] button. • If the LED on the SM-PCE1 does not illuminate after the PC application has been launched, the firmware may not have been correctly written into the SM-PCE1. In such cases, a message such as the following will appear on the PC screen. (The message window shown below appears when Shimano STEPS Manager is being used.) Manager as an example. Storage temperature • If the message “Connect the SM-PCE1.” appears on the PC screen shortly after the SM-PCE1 has been connected to the PC, there may be a problem with the SM-PCE1. (The message window shown below appears when Shimano STEPS Manager is being used.) Connect the SM-PCE1 to the PC. * Shimano STEPS Manager is one type of PC application. 0 °C -- 40 °C Connect the SM-PCE1 to the system or to a unit according to the instructions given in the manual for the PC application (such as Shimano STEPS Manager). Troubleshooting * These Service Instructions describe the procedure using Shimano STEPS Operating temperature 5. Connect the SM-PCE1 to the system or unit Install the PC application. This completes the preparation for using the SM-PCE1. Specifications 4. Install the USB driver Install the USB driver according to the instructions given in the manual for the PC application (such as Shimano STEPS Manager). Features 1. 2. 3. 4. 3. Connect the SM-PCE1 to the PC 7. When installation is complete, the following window appears. Click the [Finish] button to close the installation wizard. If you select “Launch Shimano STEPS Manager”, Shimano STEPS Manager will be launched when you click the [Finish] button. Use the load initial firmware function to reload the firmware, and if this does not solve the problem, contact the place of purchase or the nearest bicycle manufacturer in the country of use. Displaying the manual for Shimano STEPS Manager After Shimano STEPS Manager is launched, you can select “Manual Help” from the “Help” menu on the menu bar to display the user's manual for Shimano STEPS Manager. Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222 One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan * Service Instructions in further languages are available at : http://techdocs.shimano.com Please note: specifications are subject to change for improvement without notice. (English) © May 2011 by Shimano Inc. XBC IZM Printed in Japan.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 10 Producer : Mac OS X 10.6.8 Quartz PDFContext Creator : Adobe Illustrator CS3 Create Date : 2013:11:25 18:40:18Z Modify Date : 2013:11:25 18:40:18ZEXIF Metadata provided by EXIF.tools