Shimano PCE1 Di2 PC Linkage User Manual

User Manual: Shimano PCE1 Di2 PC Linkage User Manual

Open the PDF directly: View PDF PDF.
Page Count: 10

1
All information on this page as of Apr. 27th 2012.
Line-up Chart
Version 1.4
RD-9070-SS
FD-9070-F
Caliper brake
FC-9000
SM-BB92-41B
SM-BB9000
HOLLOWTECH-II
W/BB cup unit
Press - Fit type BB
BB unit
50-34T
52-36T
52-38T
53-39T
54-42T
55-42T
CS-9000
11-speed HG CS
11-23T
11-25T
11-28T
12-25T
12-28T CN-9000
Super narrow
HG chain
for 11-speed
BR-9000
Direct mount
caliper brake / Front
BR-9010-F
Direct mount
caliper brake / Rear
BR-9010-R
Cable adjuster
for BR-9010
SM-CB90
CP-W020
(10-speed)
CP-W024
(10-speed)
CP-WH23
CP-W184
Spoke protector
PD-9000
SPD-SL Pedal
Brake cable
BC-9000
HB-9000
FH-9000
WH-9000-C75-TU
75mm deep
Carbon Tubular
Wheel set
WH-9000-C50-TU
WH-9000-C50-CL
50mm deep
Carbon Tubular
Wheel set
50mm deep
Carbon/Aluminum
Clincher
Wheel set
WH-9000-C35-TU
WH-9000-C35-CL
35mm deep
Carbon Tubular
Wheel set
35mm deep
Carbon/Aluminum
Clincher
Wheel set
WH-9000-C24-TL
Carbon/Aluminum
Road Tubeless
Wheel set
WH-9000-C24-CL
Carbon/Aluminum
Clincher
Wheel set
Direct mount
9070 series
SM-EWC2
Cord cover
SW-R610
Remote sprinter
shifter
EW-SD50
Electric wire for
external wire routing
2 pcs
SM-EW90-A
Junction
for cockpit area
3 port
SM-EW90-F
Junction
for cockpit area
with wireless unit
5 port
SM-EW90-F
Junction
for cockpit area
with wireless unit
5 port
ST-9070
Remote TT/Time
trial shifter
New 1 button
design
SW-9071
Remote Triathlon
shifter
Current 2 button
design
SW-R671
Remote satellite
shifter
(Climbing shifter)
SW-R600
Dual control lever
ST-9071
Dual control
lever
SM-JC40
Junction
SM-JC41
Junction
Built-in type
SM-BMR2-L/S/I
Battery mount
SM-BCR1
Battery charger
SM-BCC1
Cord for SM-BCR1
SM-BA01
Battery cage adapter
SM-BTR1
Battery
SM-BTR2
Battery
Built-in type
SM-BCR2
Battery charger
for SM-BTR2
TT/TRI spec
(2×11-speed)
SM-AD90
Band adapter
EW-SD50-I
Electric wire for
built-in type
wire routing
4pcs for
SM-JC40/41
EW-SD50
Electric wire for
external wire
routing
External wire routing
Built-in wire routing
Around cockpit area
SM-HRR1
Heart rate monitor
SM-SPD1
Speed sensor
SC-R770
Cycle computer
Wireless type
Line-up Chart
,0*BSVG
20
All information on this page as of Apr. 27th 2012.
Electric wire routing
< DURA-ACE 9070 series >
Built-in battery mount type (Internal wire routing)
Connector
Junction (SM-JC41)
Hole
External battery mount type (Internal wire routing)
Junction (SM-JC41)
Connector
Hole
External battery mount type (External wire routing)
Junction (SM-JC40)
Connector
Junction
(SM-JC40)
,0*BSVG
22
All information on this page as of Apr. 27th 2012.
Technical Information
Version 1.4
Electric wire routing around cockpit area
1. Drop handle type
1-1. 3 port type
E-tube connector
Connector for remote sprinter shifter
ST-9070 ST-9070
SM-EW90-A
Junction-A
SW-R600
option
SW-R610
option
SW-R610
option
SM-JC40/41
Junction-B
Port for remote
sprinter shifter
E-tube port ×2E-tube port ×2Port for remote
sprinter shifter
E-tube port ×3
Technical Information
23
All information on this page as of Apr. 27th 2012.
Technical Information
Version 1.4
1-2. 5 port with wireless unit type
SW-9071
option
SW-R671
option
SM-EW90-F
Junction-A
E-tube port ×5
SC-R770SW-R610
option
SW-R600
option
SW-R610
option
SM-JC40/41
Junction-B
E-tube connector
Connector for remote sprinter shifter
Wireless
or
ST-9070
ST-9070
Port for remote
sprinter shifter
E-tube port ×2E-tube port ×2Port for remote
sprinter shifter
Technical Information
24
All information on this page as of Apr. 27th 2012.
Technical Information
Version 1.4
2. TT / Triathlon handle type
2-1. 5 port with wireless unit type
SW-9071
option
SW-R671
option
SM-EW90-F
Junction-A
E-tube port ×5
SC-R770 SM-JC40/41
Junction-B
E-tube connector
Connector for remote sprinter shifter
Wireless
or
ST-9071 ST-9071
6
18
Technical Information
7
All information on this page as of Apr. 27th 2012.
Technical Information
Version 1.4
2. Battery holder and junction
Short size
Battery Holder
SM-BMR2-S (External wire routing)
SM-BMR2-I (Internal wire routing)
SM-BMR2-L (External wire routing)
Long size
Battery Holder
Long size
Battery Holder
Junction
SM-JC40 (External mount type)
30
13
Junction
SM-JC41 (Built in type)
8
53.6
30
14.3
Technical Information
PC Linka
g
e
SM-PCE1
1Y7EA0200
0
USB Cable
2Y7EA0300
0
PC Link Cable
Feb.-2011-3138
© Shimano Inc. I
Specifications are subject to change without notice.
CODE NO.
SHIMANO
ITEM
NO. DESCRIPTION
SM-PCE1
1
2
2
4. If you would like Shimano STEPS Manager to be available for use
by all users of the PC, select
“Anyone who uses this computer
(all users)”. If you would like only
the current user of the PC to be
able to use the application, select
“Only for me”. After making the
selection, click the [Next] button.
7. When installation is complete, the following window appears.
Click the [Finish] button to close the
installation wizard. If you select
“Launch Shimano STEPS
Manager”, Shimano STEPS
Manager will be launched when
you click the [Finish] button.
Te c h n i c a l Ser vi ce I n s t r uc t i o n s SI-7EA0A-002
SM-PCE1
•Do not use outdoors or in environments with high humidity.
•Do not place the SM-PCE1 on dusty floors when using it.
•Place the SM-PCE1 on a stable surface such as a table when
using it.
•Do not place any objects on top of the SM-PCE1 or its cables.
•Do not wrap the cables into bundles.
•Do not hold the SM-PCE1 by the cables when carrying it.
•Do not apply excessive tension to the cables.
•Do not use any USB cable other than the USB cable which is
supplied with the SM-PCE1.
•Connect the SM-PCE1 directly to a computer, without using an
intermediate device such as a USB hub.
•Do not ride the bicycle while the SM-PCE1 and cable are still
connected to it.
•Do not connect two or more of the same units to the same
connection point. If this is not done, the units may not operate
correctly.
•Do not connect or disconnect units again while unit recognition is
in progress or after recognition is complete. If this is not done,
the units may not operate correctly.
Check the procedures which are given in the user's manual for
the PC application when connecting and disconnecting units.
•After connecting the battery and launching the PC application,
be sure to disconnect the SM-PCE1 from the bicycle and then
disconnect and reconnect the battery. If this is not done, the
system may not operate correctly.
•The tightness of the PC link cable will tend to drop after
repeated connections and disconnections. If this happens,
replace the cable.
•Do not wash the SM-PCE1 or wipe it using detergents.
•Do not connect two or more SM-PCE1 units to the same PC at
the same time. If two or more SM-PCE1 units are connected,
they will not operate correctly. In addition, operating errors may
occur at the PC and it may require the PC to be restarted.
NOTE
* Service Instructions in further languages are available at :
http://techdocs.shimano.com
Please note: specifications are subject to change for improvement without notice. (English)
© May 2011 by Shimano Inc. XBC IZM Printed in Japan.
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
SI-7EA0A-002-00
Operating temperature
Specifications
Compatible PCs
1. Downloading the PC application
Storage temperature
Operating/ storage humidity
Rated voltage
Rated power
Interface
Port type
Dimensions
Weight
LED
Accessories: * PC link cable (x 2) 2 m
* USB cable (x 1) 50 cm
(as of 1 November 2010)
0 °C -- 40 °C
– 20 °C -- 70 °C
10 -- 95 % RH/ 10 -- 95 % RH
5 V ± 5 %
2.5 W
USB 2.0 (Full Speed)
At PC: A type
At SM-PCE1: Mini B type
96.4 x 53.4 x 22 mm
80 g
During normal operation: Illuminated
During charging: Flashing
Operating system
Required components
Other hardware
Windows XP 32bit/64bit (SP2 or higher)
Windows Vista 32bit/64bit
Windows 7 32bit/64bit
.NET Framework 3.5
USB 1.1/2.0
Active Internet connection
Display resolution:
XGA (1024 x 768 dots) or higher
The PC application can be obtained by downloading it from
http://media.shimano.com. You will need the following user ID and
password at this time.
•User ID: shimano •Password: 2s8m8n3
2. Installing the PC application
After downloading the PC application, run the Installer to install it to the
PC by the following procedure. (The screenshots below show examples
of installing Shimano STEPS Manager to a PC which is running
Windows XP.)
Features
The SM-PCE1 can be used to connect a PC to the bicycle (system or
unit), and a PC application (such as Shimano STEPS Manager) can be
used to carry out tasks such as problem diagnosis of single units and
the whole system, updating firmware*, and retrieving logs. For details on
operating the PC, refer to the manual for the PC application.
* Firmware: the software inside each unit
3. Connect the SM-PCE1 to the PC
When the PC application is run, a “Connect the SM-PCE1.” message
will be displayed, so connect the USB cable of the SM-PCE1 to the PC.
4. Install the USB driver
Install the USB driver according to the instructions given in the manual
for the PC application (such as Shimano STEPS Manager).
Connect the SM-PCE1 to the system or to a unit according to the
instructions given in the manual for the PC application (such as
Shimano STEPS Manager).
1. Run the Installer. Select the
language in the window which
appears, and then click [OK].
2. Click the [Next] button.
3. If you agree to the terms of the
Software License Agreement, click
the [Yes] button.
5. Select the installation folder and
then click the [Next] button.
6. Installation will begin when you
click the [Install] button.
After Shimano STEPS Manager is
launched, you can select “Manual
Help” from the “Help” menu on the
menu bar to display the user's
manual for Shimano STEPS
Manager.
Displaying the manual for Shimano STEPS Manager
After purchasing the SM-PCE1, follow this procedure to prepare the
SM-PCE1 for use.
1. Download the PC application from the website.
2. Install the PC application.
3. Connect the SM-PCE1 to the PC.
4. Install the USB driver.
• For details, refer to the manual for the PC application.
• The method for displaying the manual for Shimano STEPS Manager
is given in “Displaying the manual for Shimano STEPS Manager”.
5. Connect the SM-PCE1 to the system or to a unit.
This completes the preparation for using the SM-PCE1.
*These Service Instructions describe the procedure using Shimano STEPS
Manager as an example.
*Shimano STEPS Manager is one type of PC application.
Flow of operation when using the
SM-PCE1 for the first time Troubleshooting
•If the message “Connect the SM-PCE1.”appears on the PC screen
shortly after the SM-PCE1 has been connected to the PC, there may
be a problem with the SM-PCE1. (The message window shown
below appears when Shimano STEPS Manager is being used.)
If the same problem occurs even after repeatedly disconnecting and
reconnecting the USB cable, contact the place of purchase or the
nearest bicycle manufacturer in the country of use.
•If the LED on the SM-PCE1 does not illuminate after the PC
application has been launched, the firmware may not have been
correctly written into the SM-PCE1. In such cases, a message such
as the following will appear on the PC screen. (The message window
shown below appears when Shimano STEPS Manager is being
used.)
Use the load initial firmware function to reload the firmware, and if
this does not solve the problem, contact the place of purchase or the
nearest bicycle manufacturer in the country of use.
5. Connect the SM-PCE1 to the system
or unit

Navigation menu