EV RD M662 2814 Shimano SLX Rear Derailleur User Manual
User Manual: Shimano SLX M662 Rear Derailleur User Manual
Open the PDF directly: View PDF 
.
Page Count: 3
RD-M662 (GS)
RD-M662 (SGS)
SHIMANO SLX Rear Derailleur
Long Cage
Super Long Cage
DESCRIPTION
SHIMANO
CODE NO.
ITEM
NO.
0803-2814
1
2
3
4
5
6
7
8
9
10
Y-5W7
Y-5W7
Y-5W7
Y-5W7
Y-5UC
Y-5W7
Y-5WM
Y-5WM
Y-5WM
Y-5VN
Y-5W7
Y-5W7
98110
98120
98020
98030
14000
22000
98010
98020
98050
98090
09100
10100
B-Axle Assembly
B-Tension Adjusting Screw (M4 x 18) & Plate
Stroke Adjusting Screws & Plate
Cable Fixing Bolt (M5 x 8) & Plate
P-Seal Ring
P-Tension Spring
Outer Plate Assembly (GS-Type)
Outer Plate Assembly (SGS-Type)
Guide Pulley Bolt & Tension Pulley Bolt Set
Guide & Tension Pulley Unit
Inner Plate (GS-Type)
Inner Plate (SGS-Type)
INTERCHANGE-
ABILITY
A: Same parts.
B: Parts are usable, but differ in materirals, appearance, finish, size, etc.
Absence of mark indicates non-interchangeability.
7
10
5
6
7
9
10
3
4
1
2
M4×
1
6
.
5
M4×
1
8
.
7
8
M5×12.45
M5×13.95
SGS Type
3. Chain length on bicycles with rear suspension
!"#$%#&'("$)*$+$,-%%$./01$2#3#&2-&'$)&$("#$4).#4#&($)*$("#$0#/0
5653#&5-)&7 8#9/65#$)*$("-5:$/&$#;9#55-.#$%)/2$4/1$<#$3%/9#2
)&$("#$20-.#$515(#4$-*$("#$9"/-&$%#&'("$-5$())$5")0(7 =#($("#
%#&'("$)*$("#$9"/-&$<1$/22-&'$(,)$%-&>5$()$("#$9"/-&$,"#&$("#$0#/0
5653#&5-)&$-5$/($/$3)5-(-)&$,"#0#$2-4#&5-)&$?+?$-5$%)&'#5($/&2
("#$9"/-&$-5$)&$("#$%/0'#5($530)9>#($/&2$("#$%/0'#5($9"/-&0-&'7 @*
("#$/4)6&($)*$4).#4#&($)*$("#$0#/0$5653#&5-)&$-5$%/0'#:$("#
5%/9>$-&$("#$9"/-&$4/1$&)($<#$(/>#&$63$30)3#0%1$,"#&$("#$9"/-&$-5
)&$("#$54/%%#5($9"/-&0-&'$/&2$54/%%#5($530)9>#(7
4. Outer casing length
ABC$D))5#&$("#$8E(#&5-)&$/2F65(4#&($590#,$6&(-%$-($-5$-&$("#
3)5-(-)&$5"),&$-&$("#$-%%65(0/(-)&7
AGC$H"#9>$("/($("#0#$-5$#&)6'"$5%/9>$-&$("#$)6(#0$9/5-&'7 I#;(:
/%-'&$("#$)6(#0$9/5-&'$,-("$("#$<)(()4
#2'#$)*$("#$)6(#0$9/5-&'$")%2#0$/($("#
0#/0$2#0/-%%#60$/&2$("#&$96($)*$/&1$#;9#55
%#&'("$)*$)6(#0$9/5-&'7
H)&	($("#$9/<%#$()$("#$0#/0
2#0/-%%#60$/&2:$/*(#0$(/>-&'$63
("#$-&-(-/%$5%/9>$-&$("#$9/<%#:$
0#E5#960#$()$("#$0#/0
2#0/-%%#60$/5$5"),&$-&$("#
-%%65(0/(-)&7
SLX
SL-M660
SIS-SP41
RD-M662
SGS / GS
FH-M665
9
CS-HG80
CN-HG73
SM-SP17
!# 9 " & - 9 / % $ = # 0 . - 9 # $ @ & 5 ( 0 6 9 ( - ) & 5 SI-5WM0A-002
RD-M662
+22$G$%-&>5$A,-("$("#$9"/-&$)&$<)("$("#$%/0'#5(
530)9>#($/&2$("#$%/0'#5($9"/-&0-&'C
D/0'#5(
530)9>#(
H"/-&
D/0'#5(
9"/-&0-&'
J#/0$2#0/-%%#60
=#0-#5
J+K@LM@JN$A="-*(-&'$%#.#0C
O6(#0$9/5-&'
J#/0$2#0/-%%#60
!13#
M0##"6<
P#/05
H/55#((#$530)9>#(
H"/-&
8)(()4$<0/9>#($'6-2#
In order to realize the best performance, we recommend that the following
combination be used.
Specifications
Q)2#%$&64<#0
!1 3 #
P#/05
!)(/%$9/3/9-(1
Applicable sprocket combination
=4/%%#5($530)9>#(
M0)&($9"/-&,"##%$())("$2-**#0#&9#
JLEQRRG
=P=
S
TU!
11 - 32T, 11 - 34T
BB!
GG!
Rear Derailleur
P=
S
VU!
BB!
GG!
Installation of the rear derailleur
U$44$+%%#&$>#1 L0)3)6(
80/9>#(
Bracket spindle
Tightening torque :
8 - 10 N·m {70 - 86 in. lbs.}
General Safety Information
WARNING
W@*$-($-5$2-**-96%($()$-&5(/%%$("#$,"##%:$-&5(/%%$("#$X6-9>$0#%#/5#$%#.#0$)&$("#$0)()0$5-2#7
@*$2)-&'$("-5:$4/>#$560#$("/($("#$X6-9>$0#%#/5#$%#.#0$2)#5$&)($-&(#0*#0#$,-("$("#$0)()0$/&2$("/(
<60&5$2)$&)($)99607
WY5#$(0/%$2#(#0'#&($()$9%#/&$("#$9"/-&7L)$&)($65#$/%>/%-E</5#2$)0$/9-2$</5#2$2#(#0'#&($569"
/5$065($9%#/$/5$-($4/1$0#56%($-&$2/4/'#$/&2Z)0$*/-%60#$)*$("#$9"/-&7
WY5#$("#$0#-&*)09#2$9)&	(-&'$3-&$)&%1$*)0$9)&	(-&'$("#$&/00),$(13#$)*$9"/-&7
W!"#0#$/0#$(,)$2-**#0#&($(13#5$)*$0#-&*)09#2$9)&	(-&'$3-&5$/./-%/<%#78#$560#$()$9"#9>$("#$(/<%#
<#%),$<#*)0#$5#%#9(-&'$,"-9"$3-&$()$65#7 @*$9)&	(-&'$3-&5$)("#0$("/&$0#-&*)09#2$9)&	(-&'$3-&5
/0#$65#2:$)0$-*$/$0#-&*)09#2$9)&	(-&'$3-&$)0$())%$,"-9"$-5$&)($56-(/<%#$*)0$("#$(13#$)*$9"/-&$-5
65#2:$56**-9-#&($9)&	(-)&$*)09#$4/1$&)($<#$)<(/-:$,"-9"$9)6%2$9/65#$("#$9"/-&$()$<0#/>$)0
*/%%$)**7
W@*$-($-5$	#55/01$()$/2F65($("#$%#&'("$)*$("#$9"/-&$26#$()$/$9"/&'#
-&$("#$&64<#0$)*$530)9>#($(##(":$4/>#$("#$96($/($5)4#$)("#0$3%/9#
("/&$("#$3%/9#$,"#0#$("#$9"/-&$"/5$<##&$F)-$65-&'$/
0#-&*)09#2$9)&	(-&'$3-&$)0$/&$#&2$3-&7 !"#$9"/-&$,-%%$<#
2/4/'#2$-*$-($-5$96($/($/$3%/9#$,"#0#$-($"/5$<##&$F)-$,-("$/
0#-&*)09#2$9)&	(-&'$3-&$)0$/&$#&2$3-&7
WH"#9>$("/($("#$(#&5-)&$)*$("#$9"/-&$-5$9)00#9($/&2$("/($("#$9"/-&$-5$&)($2/4/'#27@*$("#$(#&5-)&$-5
())$,#/>$)0$("#$9"/-&$-5$2/4/'#2:$("#$9"/-&$5")6%2$<#$0#3%/9#27 @*$("-5$-5$&)($2)&#:$("#$9"/-&
4/1$<0#/>$/&2$9/65#$5#0-)65$-&F6017
WObtain and read the service instructions carefully prior to installing the parts. D))5#:$,)0&$)0
2/4/'#2$3/0(5$4/1$9/65#$("#$<-919%#$()$*/%%$).#0$/&2$5#0-)65$-&F601$4/1$)9960$/5$/$0#56%(7 [#
5(0)&'%1$0#9)44#&2$)&%1$65-&'$'#&6-&#$="-4/&)$0#3%/9#4#&($3/0(57
WObtain and read the service instructions carefully prior to installing the parts. @*$/2F65(4#&(5
/0#$&)($9/00-#2$)6($9)00#9(%1:$("#$9"/-&$4/1$9)4#$)**$/&2$("-5$4/1$9/65#$1)6$()$*/%%$)**$("#$<-919%#
,"-9"$9)6%2$0#56%($-&$5#0-)65$-&F6017
WJ#/2$("#5#$!#9"&-9/%$=#0.-9#$@&5(069(-)&5$9/0#*6%%1:$/&2$>##3$("#4$-&$/$5/*#$3%/9#$*)0$%/(#0
0#*#0#&9#7
Note
W@*$'#/0$5"-*(-&'$)3#0/(-)&5$2)$&)($*##%$54))(":$,/5"$("#$2#0/-%%#60$/&2$%6<0-9/(#$/%%$4).-&'$3/0(57
W @*$("#$/4)6&($)*$%))5#7$-&$("#$%-&>5$-5$5)$'0#/($("/($/2F65(4#&($-5$&)($3)55-<%#:$1)6$5")6%2
0#3%/9#$("#$2#0/-%%#607
W\)6$5")6%2$3#0-)2-9/%%1$9%#/&$("#$2#0/-%%#60$/&2$%6<0-9/(#$/%%$4).-&'$3/0(5$A4#9"/&-54$/&2
36%%#15C7
W@*$'#/0$5"-*(-&'$/2F65(4#&($9/&&)($<#$9/00-#2$)6(:$9"#9>$("#$2#'0##$)*$3/0/%%#%-54$/($("#$0#/0$#&2
)*$("#$<-919%#7 +%5)$9"#9>$-*$("#$9/<%#$-5$%6<0-9/(#2$/&2$-*$("#$)6(#0$9/5-&'$-5$())$%)&'$)0$())$5")0(7
W@*$1)6$"#/0$/<&)04/%$&)-5#$/5$/$0#56%($)*$%))5#7$-&$/$36%%#1:$1)6$5")6%2$0#3%/9#$("#$36%%#17
W@*$("#$9"/-&$>##35$9)4-&'$)**$("#$530)9>#(5$260-&'$65#:$0#3%/9#$("#$530)9>#(5$/&2$("#$9"/-&7
WY5#$/$*0/4#$,-("$-&(#0&/%$9/<%#$0)6(-&'$-5$5(0)&'%1$2-59)60/'#2$/5$-($"/5$(#&2#&9-#5$()$-43/-0$("#
=@=$5"-*(-&'$*6&9(-)&$26#$()$-(5$"-'"$9/<%#$0#5-5(/&9#7
W+%,/15$<#$560#$()$65#$("#$530)9>#($5#($<#/0-&'$("#$5/4#$'0)63$4/0>57 I#.#0$65#$-&$9)4<-&/(-)&
,-("$/$530)9>#($<#/0-&'$/$2-**#0#&($'0)63$4/0>7
WY5#$/&$)6(#0$9/5-&'$,"-9"$5(-%%$"/5$5)4#$%#&'("$()$53/0#$#.#&$,"#&$("#$"/&2%#</05$/0#$(60
/%%$("#$,/1$()$<)("$5-2#57 M60("#04)0#:$9"#9>$("/($("#$5"-*(-&'$%#.#0$2)#5$&)($()69"$("#$<-919%#
*0/4#$,"#&$("#$"/&2%#</05$/0#$(60$/%%$("#$,/17
W+$53#9-/%$'0#/5#$-5$65#2$*)0$("#$'#/0$5"-*(-&'$9/<%#$A=@=E=KTBC7L)$&)($65#
LYJ+E+HN$'0#/5#$)0$)("#0$(13#5$)*$'0#/5#:$)("#0,-5#$("#1$4/1$9/65#
2#(#0-)0/(-)&$-&$'#/0$5"-*(-&'$3#0*)04/&9#7
WP0#/5#$("#$-&�$9/<%#$/&2$("#$-&5-2#$)*$("#$)6(#0$9/5-&'$<#*)0#$65#$()
#&560#$("/($("#1$5%-2#$30)3#0%17
WM)0$54))("$)3#0/(-)&:$65#$("#$53#9-*-#2$)6(#0$9/5-&'$/&2$("#$<)(()4$<0/9>#(
9/<%#$'6-2#7
WO3#0/(-)&$)*$("#$%#.#05$0#%/(#2$()$'#/0$5"-*(-&'$5")6%2$<#$4/2#$)&%1$,"#&
("#$*0)&($9"/-&,"##%$-5$(60&-&'7
WK/0(5$/0#$&)($'6/0/&(##2$/'/-&5($&/(60/%$,#/0$)0$2#(#0-)0/(-)&$0#56%(-&'$*0)4$&)04/%$65#7
WM)0$4/;-464$3#0*)04/&9#$,#$"-'"%1$0#9)44#&2$="-4/&)$%6<0-9/&(5$/&2$4/-&(#&/&9#$30)269(5
WM)0$/&1$X6#5(-)&5$0#'/02-&'$4#(")25$)*$-&5(/%%/(-)&:$/2F65(4#&(:$4/-&(#&/&9#$)0$)3#0/(-)&:
3%#/5#$9)&(/9($/$30)*#55-)&/%$<-919%#$2#/%#07
H"/-&$())%H"/-&
SE53##2$563#0$&/00),
9"/-&$569"$/5$
HIE]]^B$Z$HIE_PSV
`E Z ]E Z RE53##2$&/00),$
9"/-&$569"$/5$
HIE_PU^$Z$HIE_PT^
J#-&*)09#2$
9)&	(-&'$3-&
!DEHIVG$Z$!DEHIG]
!DEHIVG$Z$!DEHIG]
6.5mm
7.1mm
=-%.#0
8%/9>
J#-&*)09#2$H)&	(-&'$K-&
N&2$K-& D-&>$K-&
'
/
E
B`
!
E
=
_
@
Q
+
I
O
_
\
K
N
J
P
D
@
L
N
H
/
'
E
B
U
!
/
'
E
B
V
!
Group marks
1. Top adjustment
!60&$("#$()3$/2F65(4#&($590#,$()$/2F65($5)
("/($("#$'6-2#$36%%#1$-5$-&$%-&#$,-("$("#$)6(#0
%-&#$)*$("#$54/%%#5($530)9>#($,"#&$%))>-&'
*0)4$("#$0#/07
2. Low adjustment
!60&$("#$%),$/2F65(4#&($590#,$5)$("/($("#
'6-2#$36%%#1$4).#5$()$/$3)5-(-)&$2-0#9(%1$-&$%-&#
,-("$("#$%/0'#5($530)9>#(7
SIS Adjustment
!) 3 $ /2 F6 5( 4 #& (
590#,
P6-2#$36%%#1 Pull
Less than 30 mm
Tightening torque :
5 - 7 N·m {44 - 60 in. lbs.}
P0)).#
Note: 8#$560#$("/($("#$9/<%#$-5
5#960#%1$-&$("#$'0)).#7
D/0'#5($530)9>#(
D),$/2F65(4#&(
590#,
Cutting the outer casing
+*(#0$96((-&'$("#$)6(#0$9/5-&':$4/>#$("#$#&2$0)6&2$5)$("/($("#
-&5-2#$)*$("#$")%#$"/5$/$6&-*)04$2-/4#(#07
+((/9"$("#$5/4#$)6(#0
#&2$9/3$()$("#$96($#&2
)*$("#$)6(#0$9/5-&'7
O6(#0$#&2$9/3
!"#$5#/%#2$9/3$,-("
()&'6#$/&2$("#$06<<#0
5"-#%2$5")6%2$<#
-&5(/%%#2$()$("#$)6(#0
9/5-&'$5()33#0$)*$("#
*0/4#7 J6<<#0$5"-#%2
J6<<#0$5"-#%2
8#$9/0#*6%$&)($()$<#&2
=#/%#2$9/3$,-("$()&'6#
5. How to use the B-tension adjustment screw
Q)6&($("#$9"/-&$)&$("#$54/%%#5($9"/-&0-&'$/&2$("#$%/0'#5(
530)9>#(:$/&2$(60&$("#$90/&>$/04$()$5"-*($'#/057 !"#&$(60&$("#$8E
(#&5-)&$/2F65(4#&($590#,
()$/2F65($5)$("/($("#$'6-2#
36%%#1$2)#5$&)($-&(#0*#0#
,-("$("#$530)9>#($<6($&)($5)
9%)5#$("/($-($()69"#5$("#
9"/-&7 I#;(:$5#($("#$9"/-&
()$("#$54/%%#5($530)9>#(
/&2$0#3#/($("#$/<).#$()
4/>#$560#$("/($("#$36%%#1
2)#5$&)($()69"$("#
530)9>#(7
<Checking the distance between the largest sprocket
and the guide pulley>
=#($("#$0#/0$2#0/-%%#60$()$("#$%),#5($'#/0
3)5-(-)&:$5()3$("#$,"##%$*0)4$(60&-&':$/&2$("#&
9"#9>$("/($("#$2-5(/&9#$*0)4$("#$#2'#$)*$("#
'6-2#$36%%#1$()$("#$#2'#$)*$("#$%/0'#5($530)9>#(
-5$,-("-&$("#$0/&'#$)*$U$E$R$447 !60&$("#$90/&>
/04$()$5"-*($'#/05$/&2$9"#9>$("/($("#0#$-5$&)
0)6'"7$-&$("#$*##%7 @*$("#$&64<#0$)*$(##("$*)0$("#$9/55#((#
530)9>#($-5$9"/&'#2:$9/001$)6($("-5$5#((-&'$/'/-&7
D/0'#5($530)9>#( =4/%%#5($530)9>#(
8E(#&5-)&
/2F65(4#&($590#,
6. SIS Adjustment
O3#0/(#$("#$5"-*(-&'$%#.#0$5#.#0/%$(-4#5$()$4).#$("#$9"/-&$()$("#
G&2$530)9>#(7 !"#&:$,"-%#$30#55-&'$("#$%#.#0$F65($#&)6'"$()$(/>#
63$("#$3%/1$-&$("#$%#.#0:$(60&$("#$90/&>$/047
["#&$5"-*(-&'$()
V02
!-'"(#&$("#$)6(#0$9/5-&'
/2F65(4#&($</00#%$6&(-%$("#
9"/-&$0#(60&5$()$("#$G&2
530)9>#(7 A9%)9>,-5#C
D))5#&$("#$)6(#0$9/5-&'
/2F65(4#&($</00#%$6&(-%$("#
9"/-&$()69"#5$("#$V02$530)9>#(
/&2$4/>#5$&)-5#7 A9)6&(#0
9%)9>,-5#C
["#&$&)$5)6&2
/($/%%$-5$"#/02
Best setting
!"#$<#5($5#((-&'$-5$,"#&$("#$5"-*(-&'$%#.#0$-5
)3#0/(#2$F65($#&)6'"$()$(/>#$63$("#$3%/1$/&2$("#
9"/-&$()69"#5$("#$V02$530)9>#($/&2$4/>#5$&)-5#7
a J#(60&$("#$%#.#0$()$-(5$)0-'-&/%$3)5-(-)&$A("#$3)5-(-)&$,"#0#
("#$%#.#0$-5$/($("#$G&2$530)9>#($5#((-&'$/&2$-($"/5$<##&
0#%#/5#2C$/&2$("#&$(60&$("#$90/&>$/04$9%)9>,-5#7 @*$("#
9"/-&$-5$()69"-&'$("#$V02$530)9>#($/&2$4/>-&'$&)-5#:$(60&$("#$)6(#0
9/5-&'$/2F65(4#&($</00#%$9%)9>,-5#$5%-'"(%1$()$(-'"(#&$-($6&(-%$("#$&)-5#
5()35$/&2$("#$9"/-&$06&5$54))("%17
O3#0/(#$%#.#0$()$9"/&'#$'#/05:$/&2$9"#9>$("/($&)$&)-5#$)99605
-&$/&1$)*$("#$'#/0$3)5-(-)&57
M)0$("#$<#5($=@=$3#0*)04/&9#:$3#0-)2-9/%%1$%6<0-9/(#$/%%$
3),#0E(0/&54-55-)&$3/0(57
+2F65(4#&($<)%( +2F65(4#&($<)%(
Note:
!"#$2-5(/&9#$<#(,##&$("#$)6(#0$5()33#0$()$("#$)6(#0$9/5-&'
")%2#0$)*$("#$0#/0$2#0/-%%#60$4/1$9"/&'#$,"#&$("#$0#/0
5653#&5-)&$4).#5:$5)$2#(#04-&#$("#$%#&'("$)*$("#$)6(#0$9/5-&'$/(
("#$3)-&($,"#0#$("-5$%#&'("$-5$/($-(5$'0#/(#5(7
Note:
=#($("#$-&�$9/<%#$5)$("/($-($30)(062#5$<1$/
%#&'("$)*$%#55$("/&$/<)6($V^$44:$/&2$("#&
9"#9>$("/($("#$-&�$9/<%#$2)#5$&)($-&(#0*#0#$,-("
("#$53)>#5$)*$("#$,"##%7 =()3$("#$,"##%$*0)4
(60&-&'$,"-%#$9/001-&'$)6($("-5$5(#37
K%#/5#$&)(#b 53#9-*-9/(-)&5$/0#$56<F#9($()$9"/&'#$*)0$-430).#4#&($,-(")6($&)(-9#7 AN&'%-5"C$$c Q/1$G^^`$<1$="-4/&)$@&97 d8H$=ef$K0-&(#2$-&$g/3/&7
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
This service instruction explains how to use and maintain the Shimano bicycle parts which have been
used on your new bicycle.
For any questions regarding your bicycle or other matters which are not related to Shimano parts,
please contact the place of purchase or the bicycle manufacturer.
O6(#0$9/5-&'
O6(#0$9/5-&'$")%2#0
P6-2#$36%%#1
O6(#0$%-&#$)*$
54/%%#5($530)9>#(
AGC
ABC
Note: K#0-)2-9/%%1$9"#9>$("/($("#0#$-5
&)$'/3$<#(,##&$("#$20)3)6($/&2$("#
<0/9>#($/5$5"),&$-&$("#$-%%65(0/(-)&7
@*$("#0#$-5$/$'/3$<#(,##&$("#5#$(,)
3/0(5:$30)<%#45$,-("$'#/0$5"-*(-&'
3#0*)04/&9#$4/1$)99607
32T
ba
ba
28T
ba
24T
ba
21T
ap ba
18T
ap
a
Q
ba
ar
16T
ap
a
Q
ar
ba
14T
12T
a
Q
ar
ba
11T
a
Q
a
r
ba
C
S
-
6
J
P
A
A
N
M
9
0
H
P
Y
E
E
R
G
L
I
D
11
T
34T
ap as
30T
ap as
26T
9S
apas
23T
20T
as
as
17T
as
au
15T
as
au
13T
as
au
11T
C
S
-
6
J
P
A
A
N
M
9
0
H
P
Y
E
E
R
G
L
I
D
11
T
[Installation]
3. Operate lever B eight times or
more to set the lever to the top
position.
4. Check that the indicator needle is
pointing to the left, and align the
pin at the bottom of the indicator
and the boss on the indicator with
the omarks on the shifting lever
unit. Then insert the indicator into
the shifting lever unit as shown in
the illustration, starting with the
boss and then followed by the pin
in the reverse order to removal.
5. Tighten the two indicator fixing screws.
6. Check the operation of the indicator. If it does not operate
correctly, reinstall it while paying particular attention to steps 3
and 4.
General Safety Information
WARNING
Note
•If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving parts.
•If the amount of looseness in the links is so great that adjustment is not possible, you should replace the derailleur.
•You should periodically clean the derailleur and lubricate all moving parts (mechanism and pulleys).
•If gear shifting adjustment cannot be carried out, check the degree of parallelism at the rear end of the bicycle.Also check if the
cable is lubricated and if the outer casing is too long or too short.
•If you hear abnormal noise as a result of looseness in a pulley, you should replace the pulley.
•If the wheel becomes stiff and difficult to turn, you should lubricate it with grease.
•Do not apply any oil to the inside of the hub, otherwise the grease will come out.
•You should periodically wash the sprockets in a neutral detergent and then lubricate them again.In addition, cleaning the chain
with neutral detergent and lubricating it can be a effective way of extending the useful life of the sprockets and the chain.
•If the chain keeps coming off the sprockets during use, replace the sprockets and the chain.
•Use a frame with internal cable routing is strongly discouraged as it has tendencies to impair the SIS shifting function due to its
high cable resistance.
•Always be sure to use the sprocket set bearing the same group marks. Never use in combination with a sprocket bearing a
different group mark.
•Use an outer casing which still has some length to spare even when the handlebars are turned all the way
to both sides. Furthermore, check that the shifting lever does not touch the bicycle frame when the
handlebars are turned all the way.
•A special grease is used for the gear shifting cable (SIS-SP41).Do not use DURA-ACE grease or other
types of grease, otherwise they may cause deterioration in gear shifting performance.
•Grease the inner cable and the inside of the outer casing before use to ensure that they slide properly.
•For smooth operation, use the specified outer casing and the bottom bracket cable guide.
•Operation of the levers related to gear shifting should be made only when the front chainwheel is turning.
•If the brake fluid used in the oil disc brakes is of a type which tends to adhere to the plastic parts of the shifting lever, this may
cause the plastic parts to crack or become discolored. Therefore, you should make sure that the brake fluid does not adhere to
these plastic parts.
The mineral oil which is used in SHIMANO disc brakes does not cause cracking or discoloration if it adheres to plastic parts, but
such parts should be cleaned with alcohol beforehand to prevent foreign particles from adhering.
•Do not disassemble the indicator and shifting lever unit, as this may damage them or cause mis-operation.
•Parts are not guaranteed against natural wear or deterioration resulting from normal use.
•For maximum performance we highly recommend Shimano lubricants and maintenance products
•For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a professional
bicycle dealer.
•Check that the wheels are fastened securely before riding the bicycle.If the wheels are loose in any way, they may come off the
bicycle and serious injury may result.
•Use neutral detergent to clean the chain.Do not use alkali-based or acid based detergent such as rust cleaners as it may result
in damage and/or failure of the chain.
•Use the reinforced connecting pin only for connecting the narrow type of chain.
•There are two different types of reinforced connecting pins available.Be sure to check the table below before selecting which
pin to use.
If connecting pins other than reinforced connecting
pins are used, or if a reinforced connecting pin or tool
which is not suitable for the type of chain is used,
sufficient connection force may not be obtained, which
could cause the chain to break or fall off.
•If it is necessary to adjust the length of the chain due
to a change in the number of sprocket teeth, make the
cut at some other place than the place where the chain
has been joined using a reinforced connecting pin or an end pin. The chain will be damaged if it
is cut at a place where it has been joined with a reinforced connecting pin or an end pin.
•Check that the tension of the chain is correct and that the chain is not damaged.If the tension
is too weak or the chain is damaged, the chain should be replaced. If this is not done, the chain
may break and cause serious injury.
•Use a front chainwheel which is compatible with 9-speed chains in conjunction with Shimano
CN-7701, CN-HG93 and CN-HG73 chains. If a chainwheel for an 8-speed chain or less is used, front chainwheel gear shifting
problems may occur, or the chain pins might fall out, causing the chain to break.
•Obtain and read the service instructions carefully prior to installing the parts. Loose, worn or damaged parts may cause the
bicycle to fall over and serious injury may occur as a result. We strongly recommend only using genuine Shimano replacement
parts.
•Obtain and read the service instructions carefully prior to installing the parts. If adjustments are not carried out correctly, the
chain may come off and this may cause you to fall off the bicycle which could result in serious injury.
•Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.
Chain toolChain
9-speed super narrow
chain such as
CN-7701 / CN-HG93
8- / 7- / 6-speed narrow
chain such as
CN-HG50 / CN-HG40
Reinforced
connecting pin
TL-CN32 / TL-CN27
TL-CN32 / TL-CN27
6.5mm
7.1mm
Silver
Black
Series SLX
RAPIDFIRE (Shifting lever) SL-M660
Outer casing SIS-SP41
Rear derailleur RD-M662
Ty p e SGS / GS
Freehub FH-M665
Gears 9
Cassette sprocket
Chain
Bottom bracket guide
CS-HG80
CN-HG73
SM-SP17
Te c hn ic al Se r v ic e I ns tr u c ti on s SI-6PZRA-003
In order to realize the best performance, we recommend that the following combination be used.
Specifications
Replacing and installing the indicator
Model number
Ty p e
Gears
Total capacity
Largest sprocket
Smallest sprocket
Front chainwheel tooth difference
RD-M662
SGS GS
35T
34T
11T
22T
9
45T
34T
11T
22T
Rear Derailleur
Model number
CS-HG80
Group name
ar
au
Gears
9
9
Tooth combination
11, 12, 14, 16, 18, 21, 24, 28, 32T
11, 13, 15, 17, 20, 23, 26, 30, 34T
Cassette sprocket tooth combination
Model number
Gears
FH-M665
9
36 / 32No. of spoke holes
Freehub
g
a
-
18
T
-
S
H
I
M
A
N
O
H
Y
P
E
R
G
L
I
D
E
C
a
g
-
1
5
T
a
g
-
1
3
T
Group marks
Disassembly and reassembly should only be carried out when
removing or replacing the indicator. For the front, the direction of
rotation when removing and installing is opposite to the position of
the needle.
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003 Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222 3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
* Service Instructions in further languages are available at : http://techdocs.shimano.com
Please note: specifications are subject to change for improvement without notice. (English) © May 2009 by Shimano Inc. XBC SZK Printed in Japan.
This service instruction explains how to use and maintain the Shimano bicycle parts which have been used on your new bicycle.
For any questions regarding your bicycle or other matters which are not related to Shimano parts, please contact the place of
purchase or the bicycle manufacturer.
Installation of the sprockets
[Removal]
1. Remove the two indicator fixing screws which are securing the
indicator.
2. Lift up the lens as shown in the illustration, and then disengage
the hooked part and remove the indicator unit.
<If not installing the indicator>
1. Remove the indicator bracket protective cover which is attached
to the indicator, starting from the shorter tab as shown in the
illustration.
2. First insert the tab of the indicator bracket protective cover into
the slot which does not have a omark, and then set it onto the
shifting lever unit and secure it with the indicator fixing screw.
Reinforced Connecting Pin
End Pin Link Pin
CS-HG80 (ar)
CS-HG80 (au)
Sprocket spacer
Lock ring spacer
Lock ring spacer
Lock ring
Lock ring
•For installation of the sprockets, use
the special tool (TL-LR15) to tighten
the lock ring.
•To replace the sprockets, use the
special tool (TL-LR15) and TL-SR21
to remove the lock ring.
Tightening torque:
30 - 50 N·m {261 - 434 in. lbs.}
Gear shifting operation
This release lever is equipped with a 2-way release mechanism which allows release operations to be carried out by either pushing or pulling
the lever.
Both lever (A) and lever (B) always return to the initial position when they are released after shifting. When operating one of the levers,
always be sure to turn the crank arm at the same time.
These Service Instructions describe the operation method when using the RAPIDFIRE SL-M660 in combination with the RD-M662 top
normal-type rear derailleur. If using in combination with a reverse spring-type derailleur, the operations and indicator displays will be
reversed.
Refer to the RD-M662 (Rear Derailleur) Service Instructions for
details on installing the rear derailleur and SIS adjustment.
To sh i ft f ro m a s ma ll sp ro c ke t t o a l a rg er sp r o cke t
(Lever A)
To shift one step only, press lever (A) to the (1) position. To shift two
steps at one time, press to the (2) position.
To sh if t fr o m a la rg e s p ro ck et t o a sm al le r s p ro ck et
(Lever B)
Press lever (B) once to shift one step from a larger to a smaller
sprocket.
Lock ring
To ol
(TL-SR21)
Disassembly
TL-LR15
Lever (A) initial position Lever (B)
2-way release
Install the inner hole cover by turning it as shown in the
illustration until it stops.
Do not turn it any further than this,
otherwise it may damage the screw
thread.
Operate lever (B) eight times or
more, and check on the indicator
that the lever is at the highest
position. Then remove the inner hole
cover and connect the inner cable.
Lever (B)
Inner hole cover
Connection and securing of the inner
cable
Inner hole cover
Inner cable
Cutting the outer casing
When cutting the outer casing, cut the
opposite end to the end with the marking.
After cutting the outer casing, make the
end round so that the inside of the hole has a uniform diameter.
Attach the same outer
end cap to the cut end
of the outer casing.
Outer end cap
The sealed cap with
tongue and the rubber
shield should be
installed to the outer
casing stopper of the
frame. Rubber shield
Rubber shield
Be careful not to bend
Sealed cap with tongue
*If the rear derailleur moves to a large degree, such as in
bicycles with rear suspension, it is recommended that you
replace the cap with the
accessory aluminum cap.
The end of the outer casing
which has the aluminum cap
should be at the derailleur side. Aluminum cap
Derailleur side
Indicator unit
Shorter tab
Indicator bracket
protective cover
Shifting lever unit
Indicator bracket
protective cover
Tightening torque :
0.2 N·m {1 in. lbs.}
Tightening torque :
0.2 N·m {1 in. lbs.}
Indicator fixing screws
Indicator unit
Hooked part
Lens
Pin
Chain length on bicycles
with rear suspension
The length of A will vary depending on the movement of the rear
suspension. Because of this, an excessive load may be placed on
the drive system if the chain length is too short. Set the length of
the chain by adding two links to the chain when the rear suspension
is at a position where dimension "A" is longest and the chain is on
the largest sprocket and the largest chainring. If the amount of
movement of the rear suspension is large, the slack in the chain
may not be taken up properly when the chain is on the smallest
chainring and smallest sprocket.
A
A'
Add 2 links (with the chain on
both the largest sprocket and
the largest chainring)
Largest
sprocket
Chain Largest
chainring
If not using the indicator, this shifting lever can be installed either
on the inside or the outside of the brake lever.
If adjusting the position, remove the indicator, and then be sure
to secure it in the new position with the two fixing bolts.
•Install the shifting lever in a position where it will not obstruct brake
operation and gear shifting operation.
•Do not use in a combination which causes brake operation to be
obstructed.
•When installing the components to carbon frame/handle bar
surfaces, verify with the manufacturer of the carbon frame/parts for
their recommendation on tightening torque in order to prevent over
tightening that can cause damage to the carbon material and/or
under tightening that can cause lack of fixing strength for the
components.
Installation of the lever
Use a handlebar grip with a maximum
outer diameter of 36 mm.
Tightening torque :
5 N·m {44 in. lbs.} 4 mm Allen key
Tightening torque :
2.5 N·m {22 in. lbs.}
3 mm Allen key
Inboard Outboard
3 mm Allen key
Install the rubber seal as
the last item after replacing
the freewheel body, and make
sure that it does not get
clamped by the waterproof cap.
Replacement of the freewheel body
After removing the hub
axle, remove the freewheel
body fixing bolt (inside
the freewheel body),
and then replace the
freewheel body.
Note: Do not attempt to
disassemble the
freewheel body,
because it may result
in a malfunction.
Freewheel body Freewheel body fixing bolt
10 mm Allen key
(TL-WR37)
Disassembly
Assembly
Tightening torque :
35 - 50 N·m {305 - 434 in. lbs.}
Rubber seal
For each sprocket, the surface that has the group mark should face outward and be
positioned so that the wider part of each sprocket and the A part (where the groove width
is wide) of the freewheel body are aligned.
The groove is wide at
one place only.
a
c
-
1
4
T
A
Wide part
SI-6PZRA-003-00
Rear Drive System
1mm
NOTE:
Do not push the brake lever against the indicator cover,
otherwise it may cause problems with the operation of the
needle.
