SED2 Variable Frequency Drives Siemens Installation Instructions
User Manual: Siemens-SED2-Installation-Instructions Igor's of metalworking and electrical manuals
Open the PDF directly: View PDF .
Page Count: 8
Download | |
Open PDF In Browser | View PDF |
Installation Instructions Document No. 129-371 October 13, 2003 SED2 Variable Frequency Drives Table 1. SED2 Full Load Amp (FLA) Ratings. Product Description Provides a quick and efficient site installation of the SED2 Variable Frequency Drive (VFD). Product Numbers (leave blank) * Available with Voltage Codes 3 and 4. Example shown: SED2-0.75/22X = SED2 only, 0.75 kW (1hp), 200V to 240V, open type IP20. 1 1.5 2 3 575V 480V 240V A 5 7.5 10 15 20 25 30 40 50 60 75 100 125 3 4 5.5 7.5 11 15 19 22 30 37 45 55 75 90 C A CAUTION: 4 B B D C E D F E 0.37 0.55 0.75 1.1 1.5 2.2 3.0 4.0 5.5 7.5 11.0 15.0 18.5 22.0 30.0 37.0 45.0 55.0 75.0 90.0 WARNING: SED2 IP20 and NEMA Type 1 frame sizes and power ranges are as follows: .7 kW Output Current Max (amps) 208V to 240V (3-Phase) 2.3 3.0 3.9 5.5 7.4 10.4 13.6 17.5 22.0 28.0 42.0 54.0 68.0 80.0 104.0 130.0 154.0 — — — 380V to 480V (3-Phase) 500V to 600V (3-Phase) 1.2 1.6 2.1 3.0 4.0 5.9 7.7 10.2 13.2 18.4 26.0 32.0 38.0 45.0 62.0 75.0 90.0 110.0 145.0 178.0 — — 1.4 2.1 2.7 3.9 5.4 6.1 9.0 11.0 17.0 22.0 27.0 32.0 41.0 52.0 62.0 77.0 99.0 125.0 Warning/Caution Notations Frame Sizes and Power Ratings HP .5 HP 0.5 0.75 1.0 1.5 2.0 3.0 4.0 5.0 7.5 10.0 15.0 20.0 25.0 30.0 40.0 50.0 60.0 75.0 100.0 125.0 Your Product Number: S E D 2 / X Example Product Number: S E D 2 - 0 . 7 5 / 2 2 X Model: SED2kW: (uses 2 to 4 spaces 0.37, 0.55, 0.75, 1.1, 1.5, 2.2, plus a divider "/") 3, 4, 5.5, 7.5, 11, 15, 18.5, 22, 30, 37, 45, 55, 75, 90 Voltage: 2 = 200 to 240 3 = 380 to 480 4 = 500 to 600 NEMA: 2 (IP 20) 1 NEMA Type 1 5 NEMA Type 12 (IP 54) * Other: X include with all part #'s kW .37 .5 .75 1.1 1.5 2.2 Output Rating Personal injury/loss of life may occur if you do not follow the procedures as specified. Equipment damage, or loss of data may occur if you do not follow the procedures as specified. Required Tools F C See Mounting and Dimensions to determine correct tool sizing. SED2 IP54/NEMA Type 12 frame sizes and power ranges are as follows: HP .5 .7 1 1.5 2 3 575V 480V kW .37 .5 .75 1.1 1.5 2.2 4 5 7.5 10 15 20 25 30 40 50 60 75 100 125 3 4 5.5 7.5 11 15 19 22 30 37 45 55 75 90 B Expected Installation Time 15 minutes C D E F C Item Number 129-371, Rev. 012 http://www.sbt.siemens.com/hvp/drives Page 1 of 8 Document No. 129-371 Installation Instructions October 13, 2003 Gland Plate Installation and Conduit Connections Installation Prerequisites For Frame Sizes A, B, and C, see Figures 1 and 2 for gland plate installation and for conduit connection diameters. Circled numbers indicate the order of assembly. CAUTION: On installation of a SED2 after extended storage, see the Extended Storage: Conditioning of Capacitors section in the SED2 VFD Startup, Operation, and Maintenance Manual (Document Number 125-3201). If capacitors are not properly recharged, catastrophic damage to the drive can result. For Frame Sizes D, E, and F, see Figures 3 and 4 for conduit connection diameters. CAUTION: Install the SED2 in a climate-controlled environment that is free of moisture and conductive contaminants, such as condensation and dust. The air entering the unit for ventilation must be clean and free of corrosive materials. The ambient temperature must be between 14°F and 104°F (–10°C and 40°C) and the relative humidity must be 0% to 95% non-condensing. Do not mount unit in direct sunlight. • Bonding between conduit connections is not automatic and must be provided as part of the installation. • Each bonding conductor must be equal or greater in cross-section to the power supply cable. 3 4 Ground 2 5 Ground VFD0002R1 Conduit Connections: .90 (22.8) Figure 1. Frame Size A Gland Plate Installation and Conduit Connection Diameters in Inches (Millimeters). Page 2 of 8 http://www.sbt.siemens.com/hvp/drives Siemens Building Technologies, Inc. Document No. 129-371 Installation Instructions October 13, 2003 3 2 4 1 5 Conduit Connections: nd ou Gr VFD0003R1 Frame Size B .90 (22.8) Frame Size C .74 (18.8) .90 (22.8) 1.10 (28) .74 (18.8) 1.10 (28) Figure 2. Frame Size B & C Gland Plate Installation and Conduit Connection Diameters in Inches (Millimeters). 13.5 (343) 6.8 (173) .3 (58) 1.8 (46) ON 1 2 20 21 22 23 24 25 12 13 14 15 16 17 26 27 28 29 30 1 2 3 4 5 6 7 8 9 10 11 4.4 (112) 1.8 (46) 1.4 o(36) 9.0 (229) o 6.1 (155) o 0.25 (6) o 3.5 (89) .35 (9) VFD0091R1 PE VFD0062R1 1.77 (45.0) 1.77 (45.0) 1.10 (28.4) 1.5 (38) 14.0 (356) 1.0 (25) Figure 4. Frame Size F Conduit Connection Diameters (Bottom View) in Inches (Millimeters). 1.77 (45.0) .90 (22.8) Figure 3. Frame Size D & E Conduit Connection Diameters in Inches (Millimeters). Siemens Building Technologies, Inc. http://www.sbt.siemens.com/hvp/drives Page 3 of 8 Document No. 129-371 Installation Instructions October 13, 2003 CAUTION: Mounting and Dimensions Overheating/Ventilation: Install SED2 vertically for optimum ventilation. Do not obstruct SED2 vents. Additional ventilation may be required if SED2 is mounted horizontally. Mount the SED2 so there is a minimum clearance for ventilation and equipment access. IP20 SED2s Table 2. IP20 SED2 Overall Dimensions in Inches (Millimeters). Frame Size Height x Width x Depth Mounting Specification 6.8 x 2.9 x 5.9 (173 x 73 x 149) 8.0 x 5.9 x 6.8 (202 x 149 x 172) 9.6 x 7.3 x 7.7 (245 x 185 x 195) 20.5 x 10.8 x 9.6 (520 x 275 x 245) 25.6 x 10.8 x 9.6 (650 x 275 x 245) 33.5 x 13.8x x 12.6 (850 x 350 x 320) A B C D E F Frame Size A 2 × M4 Bolts, nuts, washers, or connecting to DIN rail 115 (13) 4 × M8 Bolts, nuts, washers 221 (25) Frame Size Frame Size C 0.22 (5.5) 5.4 (138) Vmin Clearance in Inches (Millimeters) 4 (100) 11-3/4 (300) 13-3/4 (350) A, B, C 8.0 (204) 6.9 (174) 0.17 (4.5) 2.9 (1.3) 7.5 (3.4) 12.1 (5.5) 35.3 (16) 44.1 (20) 116 (53) 26 (3.0) 4 × M5 Bolts, nuts, washers 0.19 (4.8) 6.3 (160) Weight lb (kg) 22 (2.5) 4 × M4 Bolts, nuts, washers Frame Size B 0.22 (5.5) Tightening Torque lb-in (Nm) D, E F 6.9 (174) Frame Size F Frame Size E Frame Size D Vmin. 0.59 (15) 0.68 (17.5) SIEMENS 0.68 (17.5) 31.9 (810) 24.3 (616) 19.1 (486) SED2 VFD0143R1 VFD0012R1 9.3 (235) 9.3 (235) 11.8 (300) Figure 5. IP20 SED2 Mounting Dimensions in Inches (Millimeters). Page 4 of 8 SIEMENS SED2 Vmin. NOTE: When fitted with a protective shield, allow 12-inches (305 mm) of space between each SED2. http://www.sbt.siemens.com/hvp/drives Siemens Building Technologies, Inc. Document No. 129-371 Installation Instructions October 13, 2003 NEMA Type 1 SED2s Table 3. NEMA Type 1 SED2 Overall Dimensions in Inches (Millimeters). Frame Size A B C D Height x Width x Depth Mounting Specification 9.1 x 2.9 x 5.9 (231 x 73 x 149) 11.8 x 5.9 x 6.8 (300 x 49 x 172) 13.8 x 7.3 x 7.7 (351 x 185 x 195) 24.6 x 10.8 x 9.6 (625 x 275 x 245) E 29.7 x 10.8 x 9.6 (754 x 275 x 245) F 54.5 x 16.0 x 14.0 (1384 x 406 x 356) Tightening Torque lb-in (Nm) 2 × M4 Bolts, nuts, washers, or connecting to DIN rail 4 × M4 Bolts, nuts, washers 4 × M5 Bolts, nuts, washers 0.19 (4.8) 0.22 (5.5) 3.2 (1.5) 8.3 (3.8) 13.6 (6.2) 37,5 (17.1) 22 (2.5) 26 (3.0) 115 (13) 46.4 (21.1) 4 × M8 Bolts, nuts, washers 221 (25) Frame Size C Frame Size 0.22 (5.5) A, B, C Frame Size B Frame Size A 8.0 (204) 6.9 (174) 6.3 (160) 200 (91) Vmin Clearance in Inches (Millimeters) 4 (100) 11-3/4 (300) 13-3/4 (350) D, E F 0.17 (4.5) Weight lb (kg) 5.4 (138) 6.9 (174) Vmin. Frame Size F Frame Size E 0.59 (15) Vmin. SIEMENS SIEMENS Frame Size D 0.68 (17.5) 12 in. (305 mm) 0.68 (17.5) VFD0092R2 SED2 VFD0143R1 19.1 (486) 9.3 (235) 51 (1295) 24.3 (616) 9.3 (235) Vmin. SED2 Vmin. 15 (381) Figure 6. NEMA Type 1 SED2 Mounting Dimensions in Inches (Millimeters). Siemens Building Technologies, Inc. http://www.sbt.siemens.com/hvp/drives Page 5 of 8 Document No. 129-371 Installation Instructions October 13, 2003 IP54/NEMA Type 12 SED2s Table 4. IP54/NEMA Type 12 SED2 Overall Dimensions in Inches (Millimeters). Frame Size B C D E F Mounting Clearance Top x Bottom x Sides Overall Dimensions Height x Width x Depth 15.2 x 10.6 x 10.6 (385 x 270 x 270) 23.9 x 13.8 x 11.2 (606 x 350 x 284) 27.0 x 142 x 13.9 (685 x 360 x 200) 34.8 x 14.2 x 17.8 (885 x 360 x 453) 45.3 x 17.7 x 18.6 (1150 x 450 x 473) 5.9 x 5.9 x 3.9 (150 x 150 x 100) 7.9 x 7.9 x 5.9 (200 x 200 x 150) Mounting Specification Tightening Torque lb-in (Nm) 4 × M6 Bolts, nuts, washers 44 (5) 177 (20) 0.22 (5.5) D, E F 12.3 (313) 9.1 (230) NOTE: In all cases, Smin Clearance is 5-7/8 inches (150 millimeters). Frame Size F 0.59 (15) Frame Size E Frame Size D 4 (100) 11-3/4 (300) 13-3/4 (350) A, B, C 22.2 (564) 13.5 (343) Vmin Clearance in Inches (Millimeters) Frame Size Frame Size C 0.19 (4.8) 22 (10) 42 (19) 77 (35) 105 (48) 178 (81) 115 (13) 4× M8 Bolts, nuts, washers 11.8 x 9.8 x 5.9 (300 x 250 x 150) Frame Size B Weight lb (kg) Vmin. 0.68 (17.5) SIEMENS 0.68 (17.5) 43.8 (1112) 33.5 (847) SED2 VFD0144R1 VFD0013R1 12.2 (310) Smin. Smin. Smin. 25.5 (647) SIEMENS SED2 Vmin. 15.7 (400) 12.2 (310) Figure 7. IP54/NEMA Type 12 SED2 Mounting Dimensions in Inches (Millimeters). Wiring Cable Cross-Sections for Power and Motor Cables Tightening Torque for Connecton Terminals Tables 5 through 7 provide cable cross-sections for input power cables and for motor cables. Frame Size A B C D E F Tightening Torque lb-in (Nm) 9.7 (1.1) 13.3 (1.5) 19.9 (2.25) 88.5 (10) max. 88.5 (10) max. 442 (50) Page 6 of 8 http://www.sbt.siemens.com/hvp/drives Siemens Building Technologies, Inc. Document No. 129-371 Installation Instructions October 13, 2003 Table 5. Cable Cross-Sections for Input Voltage Range 3ø AC 200V through 240V. Input Power Cable Table 6. Cable Cross-Sections for Input Voltage Range 3ø AC 380V through 480V. Motor Cable Input Power Cable Motor Cable Output Rating kW (hp) Min. CrossSection AWG (mm2) Max. CrossSection AWG (mm2) Min. CrossSection AWG (mm2) Max. CrossSection AWG (mm2) Output Rating kW (hp) Min. CrossSection AWG (mm2) Max. CrossSection AWG (mm2) Min. CrossSection AWG (mm2) Max. CrossSection AWG (mm2) 0.37 (.50) 0.55 (.75) 0.75 (1.0) 1.1 (1.5) 1.5 (2.0) 2.2 (3.0) 3 (4.0) 4 (5.0) 5.5 (7.5) 7.5 (10) 11 (15) 15 (20) 18.5 (25) 22 (30) 30 (40) 37 (50) 45 (60) 17 (1) 17 (1) 17 (1) 17 (1) 15 (1.5) 13 (2.5) 11 (4) 11 (4) 11 (4) 7 (10) 5 (16) 5 (16) 3 (25) 2 (35) 0 (50) -2 (70) -2 (70) 13 (2.5) 13 (2.5) 13 (2.5) 9 (6) 9 (6) 9 (6) 7 (10) 7 (10) 7 (10) 2 (35) 2 (35) 2 (35) 2 (35) 2 (35) -5 (150) -5 (150) -5 (150) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 15 (1.5) 11 (4) 11 (4) 7 (10) 16 (5) 5 (16) 5 (16) 2 (35) 0 (50) -2 (70) -3 (95) 13 (2.5) 13 (2.5) 13 (2.5) 9 (6) 9 (6) 9 (6) 7 (10) 7 (10) 7 (10) 2 (35) 2 (35) 2 (35) 2 (35) 2 (35) -5 (150) -5 (150) -5 (150) 0.37 (.50) 0.55 (.75) 0.75 (1.0) 1.1 (1.5) 1.5 (2.0) 2.2 (3.0) 3 (4.0) 4 (5.0) 5.5 (7.5) 7.5 (10) 0.37 (.50) 0.55 (.75) 0.75 (1.0) 1.1 (1.5) 1.5 (2.0) 2.2 (3.0) 3 (4.0) 4 (5.0) 5.5 (7.5) 7.5 (10) 11 (15) 15 (20) 18.5 (25) 22 (30) 30 (40) 37 (50) 45 (60) 55 (75) 75 (100) 90 (125) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 13 (2.5) 11 (4) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 13 (2.5) 11 (4) 9 (6) 7 (10) 7 (10) 5 (16) 3 (25) 3 (25) 2 (35) -2 (70) -2 (70) -2 (70) 13 (2.5) 13 (2.5) 13 (2.5) 13 (2.5) 13 (2.5) 9 (6) 9 (6) 9 (6) 7 (10) 7 (10) 13 (2.5) 13 (2.5) 13 (2.5) 13 (2.5) 13 (2.5) 9 (6) 9 (6) 9 (6) 7 (10) 7 (10) 7 (10) 2 (35) 2 (35) 2 (35) 2 (35) 2 (35) -5 (150) -5 (150) -5 (150) -5 (150) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 13 (2.5) 11 (4) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 13 (2.5) 11 (4) 9 (6) 7 (10) 7 (10) 5 (16) 3 (25) 2 (35) 2 (35) -2 (70) -3 (95) -3 (95) 13 (2.5) 13 (2.5) 13 (2.5) 13 (2.5) 13 (2.5) 9 (6) 9 (6) 9 (6) 7 (10) 7 (10) 13 (2.5) 13 (2.5) 13 (2.5) 13 (2.5) 13 (2.5) 9 (6) 9 (6) 9 (6) 7 (10) 7 (10) 7 (10) 2 (35) 2 (35) 2 (35) 2 (35) 2 (35) -5 (150) -5 (150) -5 (150) -5 (150) Table 7. Cable Cross-Sections for Input Voltage Range 3ø AC 500V through 600V. Input Power Cable Motor Cable Output Rating kW (hp) Min. CrossSection AWG (mm2) Max. CrossSection AWG (mm2) Min. CrossSection AWG (mm2) Max. CrossSection AWG (mm2) 0.75 (1.0) 1.1 (1.5) 1.5 (2.0) 2.2 (3.0) 3 (4.0) 4 (5.0) 5.5 (7.5) 7.5 (10) 11 (15) 15 (20) 18.5 (25) 22 (30) 30 (40) 37 (50) 45 (60) 55 (75) 75 (100) 90 (125) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 15 (1.5) 13 (2.5) 11 (4) 9 (6) 9 (6) 7 (10) 5 (16) 3 (25) 3 (25) 0 (50) -2 (70) -2 (70) 7 (10) 7 (10) 7 (10) 7 (10) 7 (10) 7 (10) 7 (10) 7 (10) 7 (10) 2 (35) 2 (35) 2 (35) 2 (35) 2 (35) -5 (150) -5 (150) -5 (150) -5 (150) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 17 (1) 15 (1.5) 13 (2.5) 11 (4) 9 (6) 9 (6) 7 (10) 5 (16) 5 (16) 3 (25) 2 (35) 0 (50) 0 (50) 7 (10) 7 (10) 7 (10) 7 (10) 7 (10) 7 (10) 7 (10) 7 (10) 7 (10) 2 (35) 2 (35) 2 (35) 2 (35) 2 (35) -5 (150) -5 (150) -5 (150) -5 (150) Siemens Building Technologies, Inc. Input Power Connection WARNING: Use only permanently wired input power connections. Connect input power to SED2 terminals L1, L2, and L3. http://www.sbt.siemens.com/hvp/drives Page 7 of 8 Document No. 129-371 Installation Instructions October 13, 2003 Motor Cable Length Motor Connection Maximum motor cable length is 164 ft (50 m). Motor cable length is given to ensure performance of only the SED2, not the suitability of the motor when connected to a SED2 at this distance. See Figure 8 for motor cable installation notes. The motor nameplate indicates the required supply voltage and method of connection (delta, ∆, or star/wye, ‘Y’, configuration). Connect motor wiring to SED2 terminals U, V, and W. See Figure 9. ! 1. Never run control or drive input wires in the same conduit as the drive output wires. 2. Keep the distance from the drive to the motor as short as possible to maximize motor life. 4. If a disconnect is mounted on the load side of your drive, it is desirable to wire an auxiliary contact to the drive that will disable drive operation when the disconnect opens. (The wiring for this contact must not be run in the same conduit as the drive output wires). SED2 VFD0014R2 M 3. If needed, use SBT-specified input line reactors to ensure a good impedance match with your drive. 5. Inverter duty motors are recommended. Install motors within their guidelines. Use dV/dT filters, output reactors, or other load conditioners as applicable or as specified by the motor manufacturer. Figure 8. Motor Cable Installation Notes. MOTOR TERMINALS VFD0029R2 U1 W2 V1 U2 W1 V2 U1 W2 V1 U2 W1 V2 Wye "Y" Figure 9. SED2 Motor Connections. Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced. Other product or company names mentioned herein may be the trademarks of their respective owners. © 2003 Siemens Building Technologies, Inc. Siemens Building Technologies, Inc. 1000 Deerfield Parkway Buffalo Grove, IL 60089-4513 U.S.A. Your feedback is important to us. If you have comments about this document, please send them to technical.editor@siemens.com Document No.129-371 Printed in the U.S.A. Page 8 of 8
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Page Count : 8 Page Mode : UseNone XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:541a1df6-1985-4570-9c92-30cc1e25c9c6 Producer : Acrobat Distiller 5.0 (Windows) Create Date : 2003:10:14 16:52:25Z Modify Date : 2003:10:23 15:40:25-05:00 Metadata Date : 2003:10:23 15:40:25-05:00 Creator Tool : Acrobat PDFMaker 5.0 for Word Document ID : uuid:9ebc7616-1cb4-402a-a472-c1c20a46098d Format : application/pdf Creator : Technical Communications Services, LRye Title : SED2 Variable Frequency Drives Description : Installation Instructions Tagged PDF : Yes Author : Technical Communications Services, LRye Keywords : HVP, 127-371, October 13, 2003 Subject : Installation InstructionsEXIF Metadata provided by EXIF.tools