Singulaire 7120 Ops&Parts Manual

User Manual: Singulaire 7120 Ops&Parts Manual

Open the PDF directly: View PDF .
Page Count: 61

Download
Open PDF In Browser	View PDF

DEPTH A(.60SINENT

METERING uNIT WITH EITHER I LITPE
On 2 LITRE HOPPER.
EXTENSIONS INCREASE CAPACITY By 6 LITRES

3701165 ZE1
3501160 ST.
& CLEANER

pooPtiii, u

EEL WHEEL

DISC GUARD
OPTIONAL 14'0IA DOUBLE DISC OPENER

STANHAY SINGULAIRE 7120 SO DIAMOND

AAPAzi S cA

DEPTH ADJUSTMENT

METERING UNIT WITH EITHER I LITRE
OR 2 LITRE HOPPER.
EXTENSIONS INCREASE CAPACITY GY 6 LITRES

370X165 ZERO PF
350X160 STAINLE
CLEANER

UNLESS STEEL WHEEL

DISC GUARD

OPTIONAL 14 - 0IA DOUBLE DISC OPENER

STANHAY SINGULAIRE 7120 100 SQUARE

Number metering units.
Mark identification number on both halves of
singulators are
each metering unit and on each singulator. (Note:
factory calibrated to ensure all units perform similarly: they must
remain fitted to the units as supplied).

Check row units. Raise machine off the ground. Then check:

Wheels:
check all wheels rotate:
cleaners.
3.

check adjustment of scrapers and

Check P.T.O. shaft. Start P.T.O., raise machine fully. If shaft angle
is not acceptable, move fan and headstock to lower position.
(Note:
fan cannot be lowered on machines with short extension brackets and
clod deflectors: adjust stop on tractor linkage control lever quadrant
instead).
If necessary, shorten P.T.O. shaft to ensure end float at
all times.

SAFETY INSTRUCTION.
Fit splined P.T.O. shaft couplings securely.
Secure shaft cover to prevent rotation in use.
4.

Check hoses. Check all hoses are correctly and securely fitted:Vacuum: front of fan connects to front tubes on metering unit (marked
V')
Pressure: rear of fan connects to rear tubes on metering unit
(marked'P').
Raise and lower machine: check hoses are not too tight, and do not
contact shafts, sprockets or chains.
(Note: unused hose stubs on the
fan must be plugged).

Check hydraulics.
hydraulic equipment.

Check drives.
Check all drive chains are in line and drive shaft
locking collars and bearing grub screws are fitted securely.

Check tyre pressures. Chain Land Drive Wheels:
Transport Wheels:

Check operation of hydraulic markers or other

1.5 bar (22 psi)
4.0 bar (59 psi)

Notes on Disconnecting Unit Drive. This procedure facilitates removal of
metering unit from chassis for fitting alternative coulters:

Pull long drive chain upwards to compress knee joint spring. With
other hand, transfer the R-clip in the end of the spring rod to a
hole exposed about 50mm down the rod. Release the drive chain from
the knee joint sprocket.

To reconnect drive, re-fit drive chain, pull upwards to compress
knee joint spring, and re-fit R-clip in normal position.

2. Check row widths. Lower machine to ground, draw forward and check row
widths at coulter tips.
3. Clean metering units. Empty seed from hopper, using removeable drain
plug.
Remove hopper side of metering units and ensure the unit is
absolutely clean.
Use soft brush to clean vacuum galleries B; dry
cloth to clean face of gallery block; air line to blow dust and s- Ea
dressing from inaccessible galleries.
(Note: remove pressure hose
from metering unit to allow dust to escape, and direct air line behind
turntable C and through hole cleaning jets E.)

IMPORTANT. METERING UNITS SHOULD BE CLEANED AT LEAST TWICE A DAY AND
AFTER WORK.
(Note: avoid using dirty or heavily dressed seed, as the unit will not
function correctly with such seed: if its use is unavoidable,
the unit must be cleaned frequently.)

PRESSURE PORT
VACUUM PORT

waLuum mcaecte nutc .

uperi

Refer to SEED SETTING GUIDE (see pages 36-42) and check seed to be
planted. Any variation from above standard arrangements is given as a
"special instruction": follow these instructions using procedures on
pages 13-15 (PREPARING METERING UNITS).
(Note: body side of metering
unit need not be removed from the row unit chassis for cleaning,
preparation or setting).

5. Choose settings.

Use SEED SETTING GUIDE to identify the following
recommended settings:

a) Seed disc (see page 16 for detailed instructions on choosing a
disc).

b) Rpm seed disc (i.e. revs/minute)
c) Vacuum m.b.
d) Pressure m.b.
Then select correct SEED SPACING CHART for the seed disc and unit drive
shaft sprocket (11T or 16T) you will be using. Use the chart to choose
the gear setting that gives the required seeding rate (see left hand
columns). Then note the forward speed that gives the recommended rpm
seed disc, and note the corresponding landwheel rpm.

6. Set gearbox(es).

The gearbox(es) are incorporated within the main
drive landwheel.
See page 17 for detailed setting instructions
(SETTING SEED SPACING).

7. Check vacuum. Ensure seed discs are free of grease and check all holes
are clear of blockage.
(Note: for care of seed discs, see page 16.)
Fit seed discs carefully over drive pegs D, concave side towards vacuum
galleries.
(Note: if one peg is marked with red paint, fit the disc so
the part number is opposite this peg.) Open fully both valves on the
fan, start tractor, engage P.T.O. Raise engine rpm until recommended
vacuum m.b. shows on vacuum gauge.
(Note:
if the gauge does not
respond immediately, refer to SETTING AIR SUPPLY, page 18.)

SAFETY INSTRUCTION. ONLY ENGAGE P.T.O. WITH ENGINE ON LOW RPM.
NEVER EXCEED 540 RPM P.T.O. SPEED.
Fit calibration handle (if available) to landwheel arm stub shaft (see
page 17). Rotate land drive wheel(s) in forward direction (using
calibration handle), and check all seed discs are seated firmly without
vibration or noise: turn over any offending disc and re-check. Having
decided which side of each seed disc should face towards the vacuum
gallery, mark the centre with a felt tipped pen, and always replace the
disc this way round. A disc may need to be turned over after some
work, but this will occur only once in its life time.
(Note: always
stop P.T.O. or remove vacuum hose before removing discs: handle discs
carefully by the edges - grease from finger marks can adversely affect
performance.)

8. Assemble metering units. Refit hopper side of metering units taking
care they are not held apart by the top sealing brush, seed guides, or
agitator gears: if necessary rotate agitator spindle F slightly.
Aaain
Lightly tighten both conical nuts A with a wrench or socket.

release; repeat several times to ensure singulators are settled in
correct working position flat on seed discs. Rotate cams to setting
16 for zero singulation. Check seed emptying plugs are securely
fitted and put seed in hoppers. Place container for collecting seed
under each unit.
b)

Rotate land drive wheel(s) in forward direction at approx. required
landwheel rpm (see page 5, paragraph 5). Check that all seed discs
are picking up seed with very few misses. (Note: better
distribution is obtained at lower vacuum levels, so do not be
tempted to increase vacuum excessively to eliminate the odd miss,
which is unavoidable with some seed.)

Select a unit whose disc is clearly visible (the "calibration
unit"). Again rotate land drive wheel at approx. required landwheel
rpm and adjust singulator cam on the calibration unit until there
are no seeds on the disc. Then gradually adjust to bring seeds back
on the disc, until there are mainly single seeds. (The lower the
setting number, the less seed will be planted.) Clamp singulator
cam with handwheel J and re-check.

When satisfied, set singulators on all remaining units to the same
setting as the calibration unit. Clamp singulator cams. Empty seed
containers into hoppers.

(Note:
when the machine is new and when fitting new or alternative
singulators, check that all units are calibrated similarly: for
procedure, see pages 14-15.)

SETTING
POINT

sowing depth is most easily achieved by progressively adjusting
coulters downwards until the desired sowing depth is achieved).

EMPTY SEED FROM HOPPERS BEFORE TRANSPORTING MACHINE TO FIELD.
Release the locking handle and adjust the depth screw. Re-tighten
locking handle.

DEPTH SCREW

LOCK I NG HANDLE

Set,

'or seeu spdclng.

b) Singulator setting:
c)
2.

must be the same setting on all units.

Hopper emptying plugs:

must be securely fitted.

Prepare the tractor.

a) Wheel tracks:
widths.

ensure front and rear wheel trackssuit
drill row
.
-

b) Lower links:
adjust levelling box until headstock pins are
horizontal: stabilizers or check chains must be fitted and adjusted
to be tight when lower links are at workinTheight.
c) Hydraulics:
markers).

connect and test any hydraulic equipment (e.g.

d) Top link:
pull forward a few metres and fully lower tractor
linkage: then adjust top link until machine headstock is vertical.
3.

Check toolbar height.
Nominal toolbar height (centre of toolbar to
ground) should be 514mm (20.25 ins.) on 60 diamond bar, and 508 (20
ins.) on 100 square bar.
On level seedbeds this is normally achieved
with landwheel struts in 3rd hole (see diagram page 17). Check height
adjacent to each land drive wheel and adjust struts if necessary.

Select tractor gear.
Lift machine, engage P.T.O. and raise engine
speed to achieve desired vacuum and pressure levels. Note tractor
engine speed, and select tractor gear to give recommended forward
speed.

Check seed delivery. Fill hoppers evenly with seed, close lids firmly.
(Note: seed should be good quality, clean, with no soil, stones, paper,
etc.: avoid using heavily dressed seed, as the dressing will be sucked
off the seed and deposited in the vacuum galleries.) Rotate land drive
wheel(s) by hand and check all seed discs are picking up and delivering
seed evenly.
If there is dampness on the coulter chutes, dry with a
cloth or by blowing air through the units: (fully close valve A, then
return it to original setting when chutes are dry).

Sowing depth: adjust coverers as necessary to achieve desired results:
re-check sowing depth and adjust all units identically.
Release the
locking handle and adjust the depth screw. Re-tighten locking handle.

CHECK FOR BLOCKED COULTERS
GO TO WORK
LOCK ING HANDLE

markers it necessary.
c) Pivot limiters:

if a yoke bar with toolbar pivots is used, check
the pivot limiters are set symmetrically and do not restrict the
toolbars pivotting in work.

d) Clamp fasteners:

after a few hectares, check all clamp fasteners
for tightness, including marker clamps.

e) Drive shaft:

after a few hectares, check drive shaft locking
collars and bearing grub screws are secure.

NOTE:

CORRECT OPERATION IS THE RESPONSIBILITY OF THE OPERATOR WHO SHOULD
CHECK PERIODICALLY THAT THE DESIRED SEEDING RATE, PLANTING DEPTH AND
MACHINE PERFORMANCE ARE BEING ACHIEVED.

a) ALWAYS lower and raise machine on the move to prevent coulter
blockage.

b) ALWAYS raise machine and check coulters for blockage if you have
c)

stopped for any reason whilst drilling.
ALWAYS move tractor linkage control lever to 'fully down' position
when going into work to ensure adequate land wheel drive.

d) ALWAYS raise machine fully when turning at headlands.
2.

Tractor forward speed

a) ALWAYS operate at the recommended forward speed.
3.

Hoppers and transport

a) ALWAYS fill hoppers with seed to the same level, and check periodically that seed levels go down evenly.

b) ALWAYS keep hopper lids firmly closed except when filling.
c) ALWAYS empty hoppers of seed before transporting machine or driving
long distances: for short distances, keep PTO engaged to ensure
discs remain seated against vacuum galleries.

Gauges and seed discs

a) REGULARLY check vacuum and pressure readings during work:
immediately investigate cause of any unexpected change of readings,
or of any unusual noise from the fan (see page 18). A loud
whistling noise from a metering unit indicates complete loss of
vacuum.
(Note: the tractor engine can be allowed to idle when the
tractor is turning or is stationary at headlands: only during work
must the vacuum and pressure be maintained.)

b) REGULARLY check unit performance.

To check seed disc pick up,
raise machine on the move at normal drilling speed, maintain
vacuum, stop and inspect seed discs.
(Note:
misses usually
indicate blocked holes in disc or unit requires cleaning.) To
check singulator setting, use one of the field check procedures on
page 21, paragraph 6.

c) ALWAYS wipe seed off the disc in the area of the singulator before
replacing hopper side of metering unit, to avoid trapping seed
between the singulator and the disc.

d) ALWAYS clean units at least twice a day and after work: do not
leave seed, seed dressing or dust in the unit overnight: if the
machine is to be out of use for more than ONE DAY, the seed discs
For care of seed
should be removed and stored in a dry place.
discs see page 16.

NOTES: 1. CORRECT OPERATION IS THE RESPONSIBILITY OF THE OPERATOR WHO
SHOULD CHECK PERIODICALLY THAT THE DESIRED SEEDING RATE,
PLANTING DEPTH AND MACHINE PERFORMANCE ARE BEING ACHIEVED.

transmission. Slacken the two adjuster frame wing nuts on the outside of
the transmission box and pivot the layshaft assembly downwards to slacken
the drive chain. REFER TO THE SEED SPACING CHARTS (pages 26-35). Hang the
drive chain over the sprocket on the layshaft as required and slide the
assembly along the shaft until the chain lines up with the appropriate
sprocket on the primary drive shaft. To tension the chain pull the
layshaft upwards and lock in position with the two adjuster frame wing
nuts.
Check that the correct gear has been selected, rotate the landwheel and
recheck chain tension, check the adjuster frame wing nuts are tight and
close the guard.

Note: Where there is more than one Drive Landwheel fitted it is
essential that all transmissions are set in the same gear
setting.
The primary drive chain is tensioned by loosening the wheel hub retaining
nuts and adjusting the chain centres by means of slots in the hub flange.
The drive from the layshaft to the main hexagon drive shaft is tensioned by
means of a nylon rubbing block.

Unit Drive
Shaft Sprocket

Gearbox
SHding Sprocket
11 24; 17130;13

FIEIDCB A
Drive Sprocket

CLAMPING FACE OF TOOLBAR MUST BE VERTICAL

The wheels must be adjusted such that the toolbar height when set squarely,
is nominally 51 cm. centre to the ground. This dimension should be checked
adjacent to each landwheel, which should be individually adjusted to allow
for variations in wheel sinkage over the width of drilling. Where
landwheels are not running in tractor wheelings, use the third hole in the
stay as a starting point before making final adjustments in the field: in
tractor wheelings use the fifth hole as a starting point.

51 cm
s==asassmassav

io prepare a PELLEIIEU A(.i1IATOR, snip off the fingers of a standard
agitator to 3mm length. The PARSNIP AGITATOR has two roll pins in
place of the rubber fingers. To fit, follow this procedure:
a)

Holding the agitator spindle with a pair of grips, unscrew gear
assembly A (left hand thread) and bolt B (left hand thread). The
complete Agitator may then be removed.

When re-assembled the Agitator should turn freely. If more end
float is required, washer C may be removed.

n
_p)
LEFT HAND
THREAD

LEFT HAND
THREAD

STANDARD AGITATOR

PARSNIP AGITATOR

PELLET AGITATOR

Remove handwheel B and lift off setting arm C and setting cam D.
Remove retaining cap A if fitted.

Lift off Singulator, and unhook spring E.

When re-assembling, ensure that springs F are located over the
bosses on the underside of the Singulator.

(Note: Singulators are factory calibrated to ensure all units perform
similarly: they must remain fitted to the units as supplied. When
fitting new Singulators, the units must be re-calibrated - see
instructions opposite.)

STANDARD SINGULATOR

SINGLE LINE SINGULATOR

a./

I I vvr IIII J

ULeUUI t.

Select your most difficult seed (for example raw carrot, raw
chicory, raw lettuce).

Follow the calibration instructions for natural carrot seed, pages
20-21, paragraphs 1-4 except clamp the singulator cam on all units
to setting 6 and leave them at this setting throughout the
calibration procedure. Then calibrate each unit individually
paragraph 5a-d) by adjusting the "eccentric boss" G until all
units deliver the same "Target Weight". (To adjust the "eccentric
boss", tighten the nut until the boss can just be turned by a
large screwdriver, then adjust by turning anti-clockwise until the
test collects the "Target Weight".)

Check in work that the seed usage from all units is similar (see
page 21, paragraph 6). If seed usage from any unit is slightly
different from the remainder, adjust the singulator until all
units perform similarly.

Vacuum Release Hole. Seed spacing benefits occasionally by fitting a
plastic plug in the vacuum release hole K. For most seed types, this
plug must not be fitted. Refer to SEED SETTING GUIDE, and check each
unit careft5TTY. When not required, the plug may be stored on the end
of the hopper lid pivot rod L.

Find the seed you wish to plant in the SEED SETTING GUIDE (see pages
36-42).
Select the number of lines you will be planting (1, 2 or 3) and
note the recommended seed disc.
(Note:
the first digit - for example
0.6 - is the diameter of each hole in mm: the second digit - for example
96 - is the number of holes in each line: a single line disc of this
specification is designated 0.6 x 96 x I line, a two line disc 0.6 x 96 x
2 line, and a three line disc 0.6 x 96 x 3 line.)

You may be given a choice of seed discs (for example, 96 or 48 holes).
If so, for faster forward speeds, choose the greater number of holes, but
for best accuracy of seed spacing when multi-line drilling , choose the
lesser number of holes.

Three disc speeds are shown: slow (12 rpm), medium (17 rpm) and fast (25
rpm). As a general rule, the slower the disc speed the better the seed
spacing, particularly with multi-line drilling. The special instructions
section on
the SEED SETTING GUIDE indicates where alternative
instructions apply.

Having selected a seed disc, refer to the SEED SPACING CHART for the
appropriate number of holes and the unit drive shaft sprocket you will be
using (11 tooth or 16 tooth).
Then check that the disc speed you have
chosen (rpm seed disc) gives an acceptable forward speed at the seed
spacing you require.

Standard seed discs are shown in the SEED SETTING GUIDE. Other discs ar
available to special order.
These include 3-line discs for carrot and
onion giving 75% seeding rate in the central line (for example 0.6 x
144/144/108; 0.8 x 96/96/72; etc.)
For full list, see page 1 of Parts
List section.

Care of Seed Discs.
Proper care of seed discs is essential to ensure
consistent performance. Follow these guidelines:
a)

Handle gently, by the edges. Do not attempt to remove from unit without
first stopping the fan or disconnecting the vacuum hose from the unit.

Store in a dry place, preferably in the original wrapping. Always remove
from machine if it is to be out of use for more than one day.

If you -suspect the disc is greasy, clean thoroughly with a solvent
solution.
(Grease can cause seeds to stick to the surface of the disc).
Always clean new discs with solvent solution before use.

Always check all holes in seed discs are clear of blockage before
refitting in units.
Blocked holes can be cleaned with fine wire, or
re-sized using a fine drill bit of the correct size.
(Note: this
operation requires extreme care.)

Always fit discs in metering unit with concave side towards vacuum
If the fit over the turntable is too tight, rub the inne
galleries.
diameter of the disc lightly with fine abrasive paper until. an exact fit
Z1-4 .1_-_
-nn nn+
Arhipvad

both the lower 'drive sprocket' and the upper 'sliding sprocket' that
are required.
There are 3 interchangeable 'sliding sprockets' in the gearbox:
a)

17T : 241
of

Standard fitment: provides the most popular range
spacings.

13T : 301

Provides spacings both above and below the standard
range.

111 For use when very close spacings are required.

(Note:
161
sprockets.)

shaft sprockets

give closer spacings than 11T shaft

2. Set seed spacing. Follow this procedure:
a)

Loosen nuts A, pivot layshaft downwards to slacken drive chain.

Check required 'sliding sprocket' is fitted: if not, follow
procedure * below.

Fit drive chain over appropriate 'drive sprocket' and 'sliding
sprocket', check that the chain is in line, and re-tension.

Turn landwheel by hand and check chain tension and drive.

* To Change Sliding Sprocket
a) Pivot layshaft until it is in line with the holes in the gearcase

Gently tap layshaft through the hole towards the wheel area, change
'sliding sprockets' as required, and tap layshaft back 'into
position.

HEIGHT ADJUSTABLE
IN 25MM STEPS

TOOLBAR HEIGHT
51AMM
(20.25)

recommended seed discs are fitted in all units.

2. Check for leaks. Check all hoses are securely connected. Check unused
vacuum and pressure ports C on fan are securely plugged.
3. Set valves. Follow this procedure:
a)

Open fully valves A and B on fan, start tractor, engage P.T.O. on
minimum engine speed.

Increase tractor engine speed until required vacuum reading shows
on vacuum gauge.

SAFETY INSTRUCTION. NEVER EXCEED 540 RPM P.T.O. SPEED.
(Note:
if the gauge does not respond immediately to the increase in
engine speed, or the belt screams, the fan drive belt is probably
slack: follow tightening procedure * below).
c)

Progressively close valve A until the required pressure reading
shows on pressure gauge.
Increase engine speed if necessary to
maintain vacuum level.
If pressure reading is too high even with
valve A fully open, remove plugs from unused pressure ports.

Pour seed into hoppers, turn land drive wheel(s) in forward
direction to prime the discs with seed, and readjust vacuum and
pressure if necessary (see notes below).

Notes on Setting Valves
a)

Increasing tractor engine speed increases both vacuum and pressure.

Closing valve A increases pressure and reduces vacuum.

Valve B is normally left fully open: closing it reduces both vacuum
and pressure.

Air inlet port G is normally left open.

Notes on Fan Maintenance
a) To adjust belt tension. Disengage P.T.O., stop tractor engine,
disconnect PTO shaft. Remove four self locking nuts E.
Remove drive cover D complete with pressure manifold.
Tension drive belt using jockey roller F. Replace drive cover and
secure with two nuts. Reconnect PTO shaft, start tractor engine,
engage P.T.0 and check fan is performing correctly. Disengage
P.T.O., stop tractor engine, remove drive cover and check drive
belt has been tracking correctly. Replace drive cover and secure
with four self locking nuts.

SAFETY INSTRUCTION. ALWAYS DISCONNECT THE P.T.O. SHAFT BEFORE
WORKING ON THE FAN UNIT.
b) Noise. The type of fan unit used on this machine should run very

Vacuum
Gauge N

(a
e
e

FKUUtUUKE.

You must have:
a)
b)
c)

Scales weighing to +/- 0.1 gram.
Container for placing under the unit to collect seed.
Calibration handle.

Choose settings. Use SEED SETTING GUIDE for CARROT - RAW/COATED (see
page 44) to select required seed disc. (Note: for most seed spacings
use a 0 0.6 x 96 hole disc, but for seed spacings over 50mm best
results are obtained using a 0 0.6 x 48 hole disc.) Then use
appropriate SEED SPACING CHART to select gear setting that gives
required seeding rate. (Use SEED POPULATION GUIDES to help calculate
field populations). Then choose either 25rpm or 17rpm seed disc speed,
based on your preferred forward speed, and note the corresponding
landwheel rpm (you will need this for the calibration procedure).

Calculate "Target Weight". From the SEED SPACING CHART (right hand
column) note the number of revs of the seed disc for 25 revs of the
landwheel in selected gear. This figure multiplied by the total number
of holes in the discs give the number of single seeds which should be
delivered for 25 revs of the landwheel.
Use the information given on the seed packet to determine the weight of
(Note: seed
this number of seeds: we call this the "Target Weight".
packets normally show seeds per 10 gram or seeds per ounce.)

(Example:
machine with 11 tooth unit drive shaft sprocket, target
seeding rate 26 per metre/8 per foot in each of 3 lines: use 0.6 x 96 x
3 line disc, in gear F13, which gives 13.3 revs of the seed disc for 25
revs of the landwheel. Number of single seeds for 25 revs of the
landwheel is therefore 13.3 x 96 x 3 = 3830. If seed packet shows 4670
seeds per 10 gram (467 per gram), the weight of 3830 seeds is 3830 ~
467 = 8.2 gram.)
4.

Set air supply. Follow this procedure:
a) Ensure vacuum release holes K of all units are unplugged (see page
15).
b) Remove hopper side of all metering units. Fit seed discs, concave
side towards vacuum galleries.
c)

Open valves A and B on fan. Start tractor engine. Raise machine
clear of ground. Engage tractor P.T.O. Increase engine rpm until
vacuum gauge reads 50 m.b.

d) Rotate land drive wheel(s) in forward direction and check all seed
discs are seated firmly without air leaks or vibration: turn over
any offending disc and re-check.
e) Replace hopper sides of all metering units, checking unit halves
coat fnnafhos.

SINGULAIRE 7120
PARTS LISTS

Contents
Page
Singulaire 7120 (line drawing)
List of seed discs

1 - la

Metering Unit - Hopper Side
- Drive Side
- Knee Joint

3 - 5
7
9

Hopper Extensions

Coulters

Fan & Drive

15 - 17

Gauges

Headstock/Fan Brackets/Parking Stand

Toolbars/Shafts/Miscellaneous

Master Landwheel/Gearbox:
- Single Type - 4.00 - 16 Tyre
- 60 x 60 toolbar
- Single Type - 6.00 - 16 Tyre
- 100 x 100 toolbar
Spring Loading Conversion

General Warranty Policy

25 - 27
29 - 31
33

Inside Back Cover

03/95

PARTS ENQUIRIES
Stanhay Webb Limited
Exning
Newmarket
Suffolk
CB8 7HD
England.
Tel: +44 (0)1638 577 206
Fax: +44 (0)1638 578 359

WHEN ORDERING PARTS PLEASE QUOTE THE FOLLOWING INFORMATION:
1. Model - SINGULAIRE 7120
2. Order number.
3. Part number and description.

PLEASE NOTE:
The parts listed are not necessarily supplied as unit items, they may
be part of an assembly or be packed in quantities.
Some of the parts shown are optional extras and are not fitted as
standard to new machines.

v.F.447

6902717 DISC SCRAPER R/H
6902718 DISC SCRAPER L/H
6902719 INSIDE DISC SCRAPER

.113%

...

8002904 3501160 STAINLESS STEEL WHEEL ANC
8002921 350X165 ZERO PRESSURE WHEEL K/1

kmoNnyilt *

SS STEEL WHEEL KIT

6902905 FRONT WHEEL CLEANER

8002760 DISC KIT

5902814 COVERER UAW-.

STANHAY SINGULAIRE 7120

6902706

No holes

6902639

0.6 x 48 x 48 x 36 special

6902868

0.5 x 12 groups of 2

6902630

0.6 x 96 x 96 x 72 special

6902970

0.5 x 12 groups of 3

6903149

0.6 x 96 x 96 x 82 special

6902865

0.5 x 24 groups of 2

6902531

0.7 x 12 groups of 3

6902533

0.5 x 12 x 1 line

6902979

0.7 x 12 groups of 4

6902489

0.5 x 24 x 1 line

6903111

0.7 x 24 groups of 3

6902488

0.5 x 48 x 1 line

6903146

0.7 x 96 x 2 line

6902557

0.5 x 48 x 2 line

6903147

0.7 x 120 x 2 line

6902400

0.5 x 48 x 3 line

6903122

0.7 x 120 x 3 line

6902532

0.5 x 96 x 1 line

6902705

0.8 x 12 groups of 2

6902558

0.5 x 96 x 2 line

6902966

0.8 x 12 groups of 3

6902690

0.5 x 96 x 3 line

6902930

0.8 x 72 x 2 line

6903095

0.5 x 144 x 2 line

6902953

0.8 x 12 groups 4 x 2 line

6902698

0.5 x 144 x 3 line

6902750

0.8 x 12 x 1 line

6902559

0.5 x 192 x 2 line

6902643

0.8 x 24 x 1 line

6902702

0.5 x 192 x 3 line

6902812

0.8 x 24 x 2 line

6902568

0.5 x 96 x 96 x 72 special

6902826

0.8 x 24 x 2 line/staggev. "

6903093

0.6 x 120 x 96 special

6902565

0.8 x 48 x 1 line

6903094

0.6 x 96 x 120 special

6902646

0.8 x 48 x 2 line

6902648

0.6 x 24 x 3 line

6902562

0.8 x 48 x 3 line

6902624

0.6 x 48 x 1 line

6902828

0.8 x 72 x 1 line

6902691

0.6 x 48 x 2 line

6902567

0.8 x 96 x 1 line

6902645

0.6 x 48 x 3 line

6902629

0.8 x 96 x 2 line

6902967

0.6 x 60 x 1 line

6902647

0.8 x 96 x 3 line

6902776

0.6 x 72 x 1 line

6902958

0.8 x 144 x 1 line

6902777

0.6 x 72 x 2 line

6903007

0.8 x 144 x 2 line

6902778

0.6 x 72 x 3 line

6003070

0.8 x 48 x inside line

6902566

0.6 x 96 x 1 line

6902632

0.8 x 96 x 96 x 72

6902637

0.6 x 96 x 2 line

6902490

1.0 x 8 x 1 line

6902563

0.6 x 96 x 3 line

6902957

1.0 x 24 x 1 line

6903092

0.6 x 120 x 2 line

6902625

1.0 x 48 x 1 line

6903071

0.6 x 144 inside line

6902829

1.0 x 72 x 1 line

6902668

0.6 x 144 x 2 line

6902670

1.0 x 96 x 1 line

6902667

0.6 x 144 x 3 line

6902623

1.0 x 96 x 2 line

6902669

0.6 x 144 x 144 x 108

6902944

1.0 x 96 x 3 line

cnnonnn

c - 10 ,1 -

1z_

1.2 x IZ groups of 3

6902775

2.0 x 72 x 1 line

6902863

1.2 x 12 x 1 line

6902582

2.0 x 12 x inside line

6902692

1.2 x 24 x 1 line

6902956

2.2 x 48 x 1 line

6902626

1.2 x 48 x 1 line

6902693

2.2 x 48 x 2 line

6902960

1.2 x 48 x 2 line

6902684

2.5 x 24 x 1 line

6902534

1.2 x 96 x 1 line

6902955

2.5 x 28 x 48 x 20 special

6902640

1.2 x 96 x 2 line

6902954

2.5 x 48 x 28 x 20 special

6902564

1.2 x 96 x 3 line

6902976

1.2 x 144 x 1 line

6902961

1.2 x 24 x inside line

6903148

1.2 x 48 x inside line

6902642

1.2 x 96 x 96 x 72

6902980

1.4 x 24 x 1 line

6902963

1.4 x 48 x 1 line

6902809

1.4 x 48 x 2 line

6902649

1.4 x 48 x 3 line

6903110

1.4 x 72 x 1 line

1 2952

1.4 x 72 x 2 line

6903109

1.4 x 72 x 3 line

6902975

1.4 x 96 x 1 line

6903139

1.4 x 96 x 1 line

6903125

1.4 x 96 x 3 line

6903140

1.4 x 96 x 96 x 72 special

6902981

1.6 x 12 groups of 2

6902864

1.6 x 12 x 1 line

6902712

1.6 x 24 x 1 line

6902821

1.6 x 48 x 2 line

6903145

1.6 x 72 x 3 line

6903144

1.6 x 96 x 2 line

6903057

2.0 x 12 groups of 2

6902810

2.0 x 48 inner & middle

6902811

2.0 x 48 inner & outer

6902651

2.0 x 8 x 1 line

6903091

2.0 x 12 x 1 line

- 3112

2.0 x 24 x 2 line

6902671

2.0 x 48 x 1 line

1 29I4

27 26 23 24,25 22 20,21

41,42, ,

18,19
14
10,11,12,13
9
7,8
2

30,31 3562

36,37

Item No:

Part No:

Description:

1
2
3
4
5
6
7
* 8
9
***10
***11
***12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
*33

7702828
2002012
6902687
6902760
7702880
2214280
2311089
6902665
2701060
6902822
6902823
2375009
2303008
7703032
7703033
6902711
2303007
7702899
2357002
2332105
2303005
2810204
6902496
2311090
6404015
6902498
6409340
2702040
2810207
2332106
2303090
7702830
6902664

*34
**35
36
37
38
39

2830040
7702861
7702860
2215260
2701062
6902666

Body - Hopper Side c/w items 2,23,27
Oilite Bearing
Felt Seal
Felt Seal - Inner Rin-g7I)
151 Pinion/Spindle c/w item 6
Tension Pin
M8 Flat Washer
Agitator Bolt - Short (L/H thread)
Singulator Spring
Singulator Spindle (spherical ball type)
Singulator Spindle End Cap
M3 x 30 Socket Head Cap Screw
M10 Hexagon Nut
Singulator - multi-line (c/w items 16,17)
Singulator - single line (c/w items 16,17)
Eccentric Singulator Pin
M8 Hexagon Nut
Singulator Brush - Hopper Side
M3 x 6 Taptite Pozidriv Pan Head Screw
M5 x 16 Slotted Cheese Head Screw
M5 Hexagon Nut
Singulator Cam
Cam Stud
M10 Flat Washer (between Cam and Body)
Handwheel
Singulator Setting Arm
10 x 25 Dowel
Singulator Arm Spring
Seed Splitter
M5 x 20 Slotted Cheese Head Screw
M5 Nyloc Hexagon Nut
Agitator - Standard
Agitator Spindle
(White - L/H thread both ends)
Agitator Finger (snap-in)
Agitator - Large Pellet
Agitator - Raw Parsnip
4 x 36 Tension Pin (finger for raw parsnip)
Primary Singulator Spring
Primary Singulator

* For Metering Units fitted with black agitator spindles, order these
parts.
** For Agitator Finger use item 34 and cut to length after fitting.
*** For Metering Units fitted with straight Singulator Spindles (no
spherical ball), order these parts.

9)vu6If■

6t6litW 1 1 07, iSqii

Outd;)(040.0y

27 26 23 24,25 22 20,21

38 39 12

41,42

■•■•
.•••••

9
18,19
14

2
32,33,34

19
29

30,31 3562

Item No:

Part No:

Description:

8002647
8002648
6902506
6902505
2311132
2211366
2212562
2705009
7402812
7402811
2357022
2810206
2705008
6902586

2 litre Hopper Lid Kit (c/w items 41-45)
1 litre Hopper Lid Kit (c/w items 41-45)
2 litre Hopper Hinge Pin
1 litre Hopper Hinge Pin
M5 Flat Washer - Large Diameter
M5 Starlock Washer - Capped
POP Rivet
Hopper Lid Clip
2 litre Hopper
1 litre Hopper
M5 x 10 Taptite Pozidriv Pan Head Screw
Unit Plug
Plug Clip
Cover Plate

41
42
43
44
45
46
47
48
49
50

KITS

8010047
8002703
8002508
8002507

Seed Splitter Kit (items 19,29,30,31)
Primary Singulator Kit (items 12,38,39)
yor '
Hopper Kit - 2 litre
Hopper Kit - 1 litre
)0"

21 22 23

5 4

2,3

14 13 12

11 10

Style 2
29

30 23

27
25
26
25

Style 1

11 10

Fit in other side

Item No:
1
2
3
4
5
6
7
* 8
** 9

Part No:

Description:

7702827
2309053
6902514
2357002
7702898
2332105
2309090
2810205
6402038

Body - Drive Side
M8 x 50 Hexagon Head Screw
Unit Conical Nut
M3 x 6 Taptite Pozidriv Pan Head Screw
Singulator Brush - Drive Side
M5 x 16 Slotted Cheese Head Screw
M5 Nyloc Hexagon Nut
Air Gallery Block
Plastic Plug

* Air Gallery Blocks:- when used to replace white air gallery blocks
in metering unit without felt seals.
To prevent leakage of small seeds (e.g. raw tomato, lettuce,
carrots) it may be necessary to fit a steel shim (part number
6902805) between body and air gallery block.
** For most seed types this plug should NOT be fitted. See SEED
SETTING GUIDE and page 15 in Operators Manual.
BODY/TURNTABLE/KNEE JOINT ASSEMBLY - STYLE 2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

7702829
6409339
2375022
2311132
1502001
6409402
1909029 2217215
6409401
7403153
6902757
2377084
2303007
2215253
6902858

Turntable c/w items 11,23
10 x 20 Dowel
M5 x 10 Taptite Pozidriv Pan Head Screw
M5 Flat Washer - Large Diameter
45T Crownwheel
Support Washer
Ball Bearing
Circlip
Support Shim (2 per unit)
241 Unit Sprocket
Unit Tab Washer
M8 x 35 Socket Button Head Screw
M8 Hexagon Nut
4 x 20 Tension Pin
Knee Joint Arm

BODY/TURNTABLE/KNEE JOIN ASSEMBLY - STYLE 1
10
11
12
14
24
25
26
27
28
29
30

7702829
6409339
2357022
1502001
7703030
4001021
1901407
2217010
1901052
7402815
2375081

Turntable c/w items 11,23
10 x 20 Dowel
M5 x 10 Taptite Pozidriv Pan Head Screw
45T Crownwheel
Knee Joint Arm c/w item 28
Metal Seal (Nilos) (2 per unit)
Ball Bearing
Circlip
Ball Bearing
24T Unit Sprocket
M8 x 20 Socket Cap Screw

•

Item No:

Part No:

Description:

1
2
3
4
5
6
7
8
9
14
15
16
17

2303008
2311216
2311090
2001002
7703107
6902804
7000022
2306028
6902858
1807018
1807022
1807045
7700400
7702695
2374066

M10 Hexagon Nut
M10 Spring Washer
M10 Flat Washer
Oilite Bearing
23/241 Knee Joint Sprocket c/w item 4
Sprocket Spacer
Clamp Spacer
M10 x 120 Hexagon Head Bolt
Knee Joint Arm
Connecting Link
Chain - 55 pitches
Chain - 161 pitches (K.J. to Drive Shaft)
11T Shaft Sprocket c/w item 18
16T Shaft Sprocket c/w item 18
M8 x 8 Socket Set Screw

ASSEMBLY

7703108

7120 Knee Joint Assembly

- 9

Item No:

Part No:

Description:

1
2

2309021
7702901
7702900
2211366
2311132
6902269
8002646
2212562
2705003

M5 x 10 Hexagon Head Screw
Extension for 2 litre Hopper - complete
Extension for 1 litre Hopper - complete
M5 Starlock Washer - Capped
M5 Flat Washer - large diameter
Hinge Pin
Lid Kit (c/w items, 3,4,5,7,8)
POP Rivet
Lid Clip

3
4
5
6
7
8

Item No:

Part No:

Description:

SINGLE LINE COULTER
1
2
3
4

2377079
6902351
3210177
3210176
3000495
3240004
3000674

M8 x 12 Socket Button Head Screw
Coulter Screw Boss
Coulter Side - L/H
Coulter Side - R/H
Coulter Insert - Cast Iron
Coulter Insert - Ceramic - Standard
Disc Drill Coulter Tip

KITS
8002617
8002550
8002812

Coulter Kit - Cast Iron
Coulter Kit - Ceramic - Standard
Coulter Kit Disc Drill

8 9
,

13 14,15

0
0

0
0
0
0

16,17

9 11,12

0
0
©

0
0
0

18,19
----,-,

17
18
24

20,21
22
23

Item No:

Part No:

Description:

7403020
7403021
7403022
2311090
2303109
6902592
2316012
4801002
6404026
2311089
7402921
2303092
2309047
6902526
7402821
7403025
7403023
7403189
6402039
2311088
2303091
6902522
2303095
7403026
6902663
2309033
7403024
7403190
6402007
6902915

Fan Drive Case - Toolbar
Fan Drive Case - Yoke Bar
Drive Cover Plate
M10 Flat Washer
M10 Nyloc Hexagon Nut - thin
Pressure Feed Hose
Hose Clip
t
Fan
Handwheel
M8 Flat Washer
Pressure Baffle
M8 Nyloc Hexagon Nut
M8 x 20 Hexagon Head Screw
Vacuum Baffle Guide
Vacuum Baffle Plate
Pressure Outlet
Vacuum Manifold - 12 row
Vacuum Manifold - 18 row
Plastic Bung (centre hole in manifold)
M6 Flat Washer
M6 Nyloc Hexagon Nut
Jockey Washer
M16 Nyloc Hexagon Nut
PTO Guard
PTO Guard Cover
M6 x 16 Hexagon Head Screw
Pressure Manifold - 12 row
Pressure Manifold - 18 row
Plastic Cap
Sealing Strip for Fan Casing
and Cover Plates

2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
-

32,43,44
37 45
42
40

20
21
27
28
29
30
31

39
41

36 28

39 40

36
37 38

Item No:

Part No:

Description:

7403020
7403021
7403022
2311090
2303109
4801002
2311089
2309047
6902522
2303095
2306135
1901051
6902589
6902590
7403191
2303008
1323002
6902587
6902872
6902871
3000632
2215587
2303078
2311093
641 3057
2311216
2306068
6902588

Fan Drive Case - Toolbar
Fan Drive Case - Yoke Bar
Drive Cover Plate
M10 Flat Washer
M10 Nyloc Hexagon Nut - thin
Fan
M8 Flat Washer
M8 x 20 Hexagon Head Screw
Jockey Washer
M16 Nyloc Hexagon Head Bolt
M16 x 90 Hexagon Head Bolt
Ball Bearing
Jockey Roller
Bearing Spacer - Jockey
Eccentric Jockey
M10 Hexagon Nut
Drive Belt - 20 rib
Drive Shaft
Bearing Spacing - 29 long
Double Bearing
Shaft Housing
PTO Pulley
4 x 40 Split Pin
M20 Hexagon Slotted Nut
M20 Flat Washer
Shaft Key M10 Spring Washer
M10 x 50 Hexagon Head Bolt
Fan Impeller Shaft

2
3
4
7
9
12
20
21
27
28
29
30
31
32
34
35
36
37
38
39
40
41
42
43
44
45

ASSEMBLIES
7702922
7702923

Fan & Drive - Toolbar Drills
Fan & Drive - Yoke Bar Drills

NOT ILLUSTRATED
4300016
4300018
5215046

Unit Hose - Black (per metre)
Unit Hose - Grey (per metre)
Cable Tie

For Yoke Bar Drills: *
2303010
46
47
48

6409358
2303092
2306042

M16 Hexagon Nut
(for attaching to yoke bar)
PTO Extension Adaptor
M8 Nyloc Hexagon Nut
M8 x 60 Hexagon Head Bolt

* Note: Item 23 not fitted
Item 22 fitted on underside

FIT PIPE TO
LOWER
NIPPLE

Item No:

Part No:

Description:

4803005
4803006
2326033

4803007
4803008
2326006

3
4
5
6
7
8
9
10

6409399
6409400
2309022
2303005
4802040
4300024
4300025
2316003

P- -1 ' 11"4-01
Vacuum Gauge 156'1" 19
Gauge Cover
6 - 32 x 5/16 Slotted Cheese Head Screw
(Fixing Screws - 3 off required)
Pressure Gauge
Gauge Cover
4 - 40 x 5/8 Slotted Cheese Head Screw
(Fixing Screws - 2 off required)
Gauge Bracket
Magnetic Foot
M5 x 12 Hexagon Head Screw
M5 Hexagon Nut
Pipe Connector
Gauge Pipe - 4.6m Long
Manifold Spigot Pipe
Hose Clip

KIT
4803004

Vacuum/Pressure Gauge Kit
(items 1-10)

6
1.17 19 20 21 19 18

12_
11

Item No:
1
2
3
4
5
6
7
8
9
10
11
*12
13
14
15
16
17
18
19
20
21

Part No:

Description:

7403040
6902672
2303011
2311219
2306164
7403031
2309108
2306128
2311218
2303010
7403178
7403179
7403180
7403181
7403028
8002134
7402141
7402238
2316033
6902100
2303009
2311217
6402018

Cat.1 Headstock
Cat.1 Headstock Spacer
M20 Hexagon Nut
M20 Spring Washer
M20 x 90 Hexagon Head Bolt
Cat.2 Headstock
M20 x 50 Hexagon Head Screw
M16 x 50 Hexagon Head Bolt
M16 Spring Washer
M16 Hexagon Nut
Fan Bracket - long - L/H
Fan Bracket - long - R/H
Fan Bracket - short - L/H
Fan Bracket - short - R/H
Toolbar Bracket
7403029 U-Bolt c/w item 3
Parking Stand
Support Pin
R-Clip
Stand Handle
M12 Hexagon Nut
M12 Spring Washer
Plastic Plug

KITS

8002708
8002676
*8002707

Cat.1 Headstock Fitting Kit
(items 2-5)
Fan Bracket (long) Kit
(items 7-11, 13-21)
Fan Bracket (short) Kit
(items 7-10, 12-21)

* Lower PTO position cannot be obtained if Clod Deflectors are fitted.

91.

81.

91-

./
RI

Item No:

1
2

4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

Part No:

Description:

6402015
7701112
7701113
7402903
7402984
7403050
7402901
7402967
7402991
7402906
7402907
6902175
6902469
6902322
7000067
7000068
6902103
7000070
7700089
6902352
2309061
8010027
2303007
2311215
2309048
7400070
8002126
7403037
7402922
6416032
8002125
7403132
2303010

Plastic Plug
2.30M Toolbar
2.90M Toolbar
1.65M Toolbar )
2.00M Toolbar )
2.15M Toolbar ) Double
2.30M Toolbar ) Box
2.90M Toolbar ) Type
3.30M Toolbar )
3.80M Toolbar )
4.27M Toolbar )
1.65M Shaft
2.00M Shaft
2.15M Shaft
2.30M Shaft
2.90M Shaft
3.30M Shaft
3.80M Shaft
Muff Coupling (to join two shafts)
Locking Collar
M10 x 20 Hexagon Head Screw
1905025 Ball Bearing c/w items 8-10
M8 Hexagon Nut
M8 Spring Washer
M8 x 25 Hexagon Head Screw
Bearing Bracket
7001098 U-Bolt c/w items 8, 9
Calibration Handle
Box Spanner - 17mm
PTO Shaft - heavy duty c/w overrun clutch
7001093 U-Bolt c/w item 18
Joining Member - 200 centres
M16 Hexagon Nut

KITS
7700996
8002781

Bearing Bracket (items 7-12)
Joining Member (items 16, 17)

ILLUSTRA1

34 39

22
26

21
7 18

10
47

4.00-

4.00-16 TYRE - ROUND WHEEL SPINDLE

WHEEL TYPES

L/H

RIH

Note: L/H and R/H wheels may be fitted on either side of drill outfits.
Item No:

Part No:

Description:

7402719
7402720
7402662
2311092
2303010
7402445
7402860
2303109
2311090
2306082
2217009
1901051
7402808
6902326
7402687
2306466
6902235
2311089
2303092
1901049
7703060
1707090
1707057
6902234
7402807
1807018
1807036

Gearbox Body L/H
Gearbox Body R/H
Clamp Half
M16 Flat Washer
M16 Hexagon Nut
Gearbox Lid L/H
Gearbox Lid R/H
M10 Nyloc Hexagon Nut - thin
M10 Flat Washer
M10 x 160 Hexagon Head Bolt
Circlip
Ball Bearing
21T Driven Sprocket
Shaft Support (non driving wheels only)
Adjuster Frame
M8 x 40 Coach Bolt
Output Drive Jockey
M8 Flat Washer
M8 Nyloc Hexagon Nut
Ball Bearing
17/24T Sliding Sprocket
13/301 Sliding Sprocket
111 Sliding Sprocket
Output Shaft
191 Output Sprocket
Connecting Link (for items 22 & 23)
Chain
-42
__ pitches
.. .
,... .

2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

19
20
21
22

(L I 1-1 I LLUSTRAT

53 36 34 55 54 33 7

34 39

37
16

14 12

26
18 21N,

3
25 8
27
24

6,--

20 10
23

44
45

21
48
44
10
47
49

4.00-16

Item No:

Part No:

24
25
26
27

2306488
6902236
6902742
6902229
6902325
28
2309063
29
2309061
30
1707083
1707084
31
32
1707085
33
7402467
34
2311091
2306097
35
36
2306097
6902230
37
38
2311370
39
2303094
40
7402434
1808065
41
42
1808066
7403158
43
44
2217208
45
3000657
46
6902673
47
7703048
5700339
48 5700336
5700337
5700333
5700334
5700335
49
5700340
50
6902239
51
2309049
52
7402446
53
2316033
54
2303009
55
2311217
56
2303013
57
6902759
58
6413059

TYRE - ROUND WHEEL SPINDLE
Description:
M10 x 30 Coach Bolt
Quadrant Washer
Adjuster Frame Nut
Arm Pivot Plate
Plate Packing (for adjustment)
M10 x 30 Hexagon Head Screw
M10 x 20 Hexagon Head Screw
16/17T Sprocket
18/19T Sprocket
20/21T Sprocket
16T Input Shaft
M12 Flat Washer
M12 x 45 Hexagon Head Bolt
M12 x 45 Hexagon Head Bolt
Wheel Strut
M10 Flat Washer - Extra Large
M12 Nyloc Hexagon Nut
Wheel Arm
Connecting Link
Chain - 87 pitches
161 Wheel Spindle
Circlip
Landwheel Hub
Bearing Spacer - landwheel
Wheel Centre c/w studs
Wheel Stud
Landwheel L/H (c/w tyre & tube)
Landwheel R/H (c/w tyre & tube)
Wheel
Tyre
Tube
Wheel Nut
Scraper Arm
M8 x 30 Hexagon Head Screw
Landwheel Scraper
R-clip
M12 Hexagon Nut
M12 Spring Washer
M30 Hexagon Nut
Tab Washer - Landwheel
Key - Wheel Centre

ASSEMBLIES
7703053
7703054

Single Landwheel L/H
Single Landwheel R/H

) Drill and
) Granyl Drive

7703049

Single Landwheel L/H

Granvl Drivp

77nnnrn

r.!

.1 -

(LIH ILLUSTRi

34 39

44
10
47

4.00-16 TYRE - ROUND WHEEL SPINDLE

WHEEL TYPES

L/H

R/H

Note: L/H and R/H wheels may be fitted on either side of drill outfits.
Item No:

Part No:

Description:

19
20
21
22

7403119
7403120
6902964
2311092
2303010
7402445
7402860
2303109
2311090
2306082
2217009
1901051
7402808
6902326
7402687
2306466
6902235
2311089
2303092
1901049
7703060
1707090
1707057
6902234
7402807
1807018
1807036

Gearbox Body L/H
Gearbox Body R/H
Clasp Plate
M16 Flat Washer
M16 Hexagon Nut
Gearbox Lid L/H
Gearbox Lid R/H
M10 Nyloc Hexagon Nut - thin
M10 Flat Washer
M10 x 160 Hexagon Head Bolt
Circlip
Ball Bearing
21T Driven Sprocket
Shaft Support (non driving wheels only)
Adjuster Frame
M8 x 40 Coach Bolt
Output Drive Jockey
M8 Flat Washer
M8 Nyloc Hexagon Nut
Ball Bearing
17/241 Sliding Sprocket
13/301 Sliding Sprocket
11T Sliding Sprocket
Output Shaft
19T Output Sprocket
Connecting Link (for items 22 & 23)
Chain - 42 pitches

1nn -innn

2
3
- 4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

(LIH ILLUSTR?

34 39

44
47

4.UU- 10 ITFL. — KUUMU WIttL

Item No:

Part No:

24
25
26
27

2306488
6902236
6902742
6902229
6902325
28
2309063
2309061
29
30
1707083
31
1707084
32
1707085
33
7402467
34
2311091
35
2306097
2306097
36
6902230
37
38
2311370
39
2303094
40
7402434
41
1808065
42
1808066
43
7403158
44
2217208
45
3000657
46
6902673
47
7703048
5700339
48 5700336
5700337
5700333
5700334
5700335
49
5700340
50
6902239
51
2309049
52
7402446
53
2316033
54
2303009
55
2311217
56
2303013
57
6902759
58
6413059

w-inuLt

Description:
M10 x 30 Coach Bolt
Quadrant Washer
Adjuster Frame Nut
Arm Pivot Plate
Plate Packing (for adjustment)
M10 x 30 Hexagon Head Screw
M10 x 20 Hexagon Head Screw
16/17T Sprocket
18/19T Sprocket
20/211 Sprocket
16T Input Shaft
M12 Flat Washer
M12 x 45 Hexagon Head Bolt
M12 x 45 Hexagon Head Bolt
Wheel Strut
M10 Flat Washer - Extra Large
M12 Nyloc Hexagon Nut
Wheel Arm
Connecting Link
Chain - 87 pitches
16T Wheel Spindle
Circlip
Landwheel Hub
Bearing Spacer - landwheel
Wheel Centre c/w studs
Wheel Stud
Landwheel L/H (c/w tyre & tube)
Landwheel R/H (c/w tyre & tube)
Wheel
Tyre
Tube
Wheel Nut
Scraper Arm
M8 x 30 Hexagon Head Screw
Landwheel Scraper
R-clip
M12 Hexagon Nut
M12 Spring Washer
M30 Hexagon Nut
Tab Washer - Landwheel
Key - Wheel Centre

ASSEMBLIES
7703194
7703195

Single Landwheel L/H
Single Landwheel R/H

7703010
77nlnii

Single Landwheel L/H
CinrOn InnAwhnell 0/14

) Drill and
) Granyl Drive
) Granyl Drive

(LIR ILLUSTRATI

Item No:

Part No:

Description:

1
2
3
4

2303094
2306097
6902689
7402838
2303044
6902536
2701056
7402837
2306105
2311091
6902537

M12 Nyloc Hexagon Nut
M12 x 45 Hexagon Head Bolt
Spring Loading Arm
Spring Locator
M10 Hexagon Locknut
Spring Tensioner Handle
Compression Spring
Pivot Arm/Spring Adjuster
M12 x 90 Hexagon Head Bolt
M12 Flat Washer
Pivot Bush

6
7
8
9
10
11

KIT
8002538

MLD Spring Loading Kit

(Note: Will fit L/H and R/H Master Landwheels)

40-Da

rtz.a

41d22 1-'44

(3-

•

(

401—
‘b6PPs' ■

C-0
•
••

STANHAY WEBB TEL NO:

4-17-'93 WED 17:38 ID:

Stanh4y Singulaire 7100 Disc

Ref. No.

Part No

Description

1807018
1807041

Connector
129P Chain

4
5

4300016
4300018

Hose Black - per metre
Hose Grey - per metre

7703005
6401018
7703007
1901046
6902780
2309078
2303092

Depth Screw Assy
Greaser
.
Trunion Carrier Assy
Bearing
Trunion Bolt
Set Screw
Nyloc Nut

2387013
2309021

Toggle Clip
Set Screw

7703001
1901101

Upper Parallel Link Assy
Bearing

2702027

Tension Spring

1905025
2303007
2311215
2309047

Bushing
Hex. Nut
Spring Washer
Set Screw

6902730
2303010

'U' Bolt
Nut

7703002
1901101

Lower Parallel Link Assy
Bearing

7703000
1901046
6401006
2303128
2309079
6902729 .

Unit Bracket Assy
Bearing
Greaser
Philidas Nut
Set Screw
Arm Pivot Spindle

6902720
2303092
2311134

Disc Guard
Nyloc Nut
Plain Washer

0638 51

Chassis

IML

Part No.

Description

8002760
7703073
2303091
2309033
6000116
7703008
1901103
2217201
7403170
6902719
6902718
6902717
2309061
2303095

Disc Kit
Disc & Nut Asy
Nyloc Nut
Set Screw
Disc
Disc Hub Assy
Bearing
Circlip
Disc Bracket
Inside Disc Scraper
Disc Scraper L/H
Disc Scraper R/H
Set Screw
Nyloc Nut

8002812
2377079
3000674
3210176
3210177
6902351

Coulter Kit
Socket Button Head Screw
Coulter Tip
Coulter Side R/H
Coulter Side L/H
Coulter Screw Boss

8002761
8002762
2303127
2309063
6902734
6902735

Arm Cover Kit R/H
Arm Cover Kit L/H
Philidas Nut
Set Screw
Coverer R/H
Coverer L/H

Zero Pressure Wheel

Ref.No.
11

8002765
2303110
2311113
7403113
16

UM3d

111-1.

■?)ji i

/li

cia
V

Zero Pressure Wheel Kit
Nyloc Nut
Washer
Rear Wheel Bolt

Stainless Steel Wheel
8002766
7703009
6902622
2303091
2303110
2311113
7403113
1901104
8002767

Wheel Cleaner Kit
Wheel Assy
Wheel Cleaner
Nyloc Nut
Nyloc Nut
Washer
Rear Wheel Bolt • YV■ 12-/..1.,W 11, 1- .)5.
Bearing
Stainless Steel Wheel Kit

1
7

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2012:02:06 14:36:27-08:00
Create Date                     : 2012:02:06 14:36:27-08:00
Metadata Date                   : 2012:02:06 14:36:27-08:00
Creator Tool                    : ScanFlowStore registered to 211645 (ID:33493676)
Format                          : application/pdf
Document ID                     : uuid:70a48731-465b-47be-b35a-0679addfe804
Instance ID                     : uuid:2e00aa90-86f8-47a6-9e7d-b4409e801f75
Producer                        : Nuance Communications, Inc.
Page Count                      : 61
Creator                         : ScanFlowStore registered to 211645 (ID:33493676)

EXIF Metadata provided by EXIF.tools

Singulaire 7120 Ops&Parts Manual

Navigation menu

Versions of this User Manual:

Views

Navigation