Stan's Neo Hub User Manual

User Manual: Stan's-Neo-Hub-User-Manual

Open the PDF directly: View PDF PDF.
Page Count: 47

Technical Manual – Neo & Neo Ultimate Hubs
Page 1
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
Table of Contents
1 General
1.1 Target Application
1.2 Safety
1.3 Warranty
1.4 Cleaning
1.5 Maintenance Intervals
2 Compatibility/Conversion
2.1 Compatibility/Conversion Charts
2.2 Bearing Specification and Part Numbers
3 Maintenance Instructions
3.1 Tools
3.2 Neo Front
3.2.1 End Cap Removal/Replacement
3.2.2 Front Hub Bearing Removal
3.2.3 Front Hub Bearing Installation
3.3 Neo Rear
3.3.1 End Cap Removal/Replacement
3.3.2 Freehub Replacement
3.3.3 Rear Hub Bearing Removal
3.3.4 Rear Hub Bearing Installation
3.3.5 Freehub Pawl & Spring Removal/Installation
3.3.6 Freehub Bearing Removal
3.3.7 Freehub Bearing Installation
3.4 Neo OS
3.4.1 OS Endcap Removal/Replacement
3.4.2 OS Front Hub Bearing Removal
3.4.3 OS Front Hub Bearing Installation
4 Hub Diagrams
Neo Front
Neo Rear
Page 2
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
Neo Freehubs
1 General
1.1 Target Application
This manual contains all applicable information regarding Stan’s NoTubes Neo series hubs. This
includes the following: Neo, Neo S, Neo OS, Neo Ultimate, Neo CL, Neo S CL, and Neo Ultimate
CL
1.2 Safety
Proper assembly maintenance, and installation are necessary for all Stan’s NoTubes Neo hubs
and wheels. Incorrect assembly or installation can lead to accidents causing severe injuries or
death.
1.3 Warranty
All Stan’s NoTubes Neo series hubs are covered by a 3 year warranty against manufacturing
defects. Warranty does not cover abuse, misuse, consequential damage resulting from incorrect
or nonexistent maintenance, normal wear and tear, and improper installation. Warranties only
apply to the original owner with valid sales receipt. If a product is found defective customer will
receive, at the discretion of Stan’s NoTubes, free repair or replacement.
1.4 Cleaning
The exterior of your Stan’s NoTubes Neo hub should be cleaned regularly to prevent surface
abrasions or discoloration which can occur from prolonged contact with acidic soils. A mild
detergent is recommended for removal of surface oils and dirt. Further cleaning of the hub
internals is outlined in the maintenance sections, respective to each hub model.
NOTICE: High-pressure water should NOT be used to clean a Neo hub. This can result in water
infiltration past the bearing seals, and will reduce the life of the bearings.
O-ring and SealLock seal care: Water and a mild detergent (such as Dawn dish soap) and
isopropyl alcohol are recommended to clean the o-rings and end cap seals of Stan’s NoTubes
Neo Hubs. Use of harsh chemicals will swell and degrade the o-ring/seal.
Page 3
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1.5 Maintenance Intervals
Periodic inspection and cleaning of your Neo hubs will keep them in excellent working condition.
When inspecting the hub, make sure there is not excessive play in the wheel and that the
bearings roll smooth. If the wheel is loose or the bearings roll rough one or more cartridge
bearings may be worn. Check the freehub for smooth rotation and proper engagement. Utilize
the Table 1 on the next page, to estimate service intervals for all Stan’s NoTubes Neo hubs:
Table 1: Service Intervals for Stan's NoTubes Neo hubs
Page 4
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
2 Compatibility/Conversion
Stan’s NoTubes Neo hubs are available in multiple axle configurations and can be converted to
fit most popular axle standards found on today’s road and mountain bikes.
2.1 Compatibility/Conversion Charts
Utilize the tables 2 and 3 on the next pages to determine axle standard compatibility for each
Neo hub model.
Table 2: Stan’s NoTubes Neo Hub Axle Standard Compatibility/Conversion Chart
9x100mm QR
9x100mm Thru Bolt
12X100mm Thru Axle
15x100mm Thru Axle
15x110mm Thru Axle
20x110mm Thru Axle
10x130mm QR
10x135mm QR
10x135mm BO
10x135mm Thru Bolt
12x135mm Thru Axle
12x142mm Thru Axle
12x148mm Thru Axle
12x150mm Thru Axle
12x157mm Thru Axle
Shimano/SRAM 9/10/11
Campangolo 9/10/11
SRAM XD
Singlespeed
Neo ◉○ ○ ● ◉○ ○ ● ● ● ●
Neo OS ◉● ● ◉● ○ ●
Neo (Boost) ● ● ● ○ ●
Neo CL ◉○ ● ◉○ ○ ● ● ● ●
Neo Singlespeed ◉○ ● ●
Neo S ◉○ ○ ● ◉○ ○ ● ● ● ○
Neo S CL ◉○ ● ◉○ ○ ● ● ● ○
Neo Ultimate ◉○ ○ ● ◉○ ○ ● ● ● ●
Neo Ultimate (Boost) ● ● ● ○ ●
Neo Ultimate CL ◉○ ● ◉○ ○ ● ● ● ●
Neo Ultimate Singlespeed ◉○ ● ●
Hub
Front
Rear
Freehub
Page 5
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
Table 3: Stan’s NoTubes Neo Hub End Cap Conversion Charts
10x135mm QR
10x135mm BO
10x135mm Thru Bolt
12x135mm Thru Axle
12x142mm Thru Axle
12x148mm Thru Axle
12x150mm Thru Axle
12x157mm Thru Axle
Neo
ZH07803ZH07705ZH0781 ZH0778 ZH0779
Neo OS ZH0778 ZH0779
Neo (Boost) ZH0779
Neo CL
ZH09574ZH0987 ZH0988 ZH0956
Neo Singlespeed
ZH07803ZH07705ZH0779
Neo S
ZH07803ZH07705ZH0781 ZH0778 ZH0779
Neo S CL
ZH09574ZH0787 ZH0988 ZH0956
Neo Ultimate
ZH07803ZH07705ZH0781 ZH0778 ZH0779
Neo Ultimate (Boost) ZH0779
Neo Ultimate CL
ZH09574ZH0987 ZH0988 ZH0956
Neo Ultimate Singlespeed
ZH07803ZH07705ZH0781 ZH0778 ZH0779
3 = Also available in kit including 135mm QR lever (ZH0769)
4 = Also available in kit including 135mm QR lever (ZH0962)
5 = Kit includes axle, end caps and bolts
Rear Hub End Cap Kit Part Numbers
Page 6
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
2.2 Bearing Specification and Part Numbers
Use Table 4 below to find the proper bearing size and quantity for your hub and Table 5 to find
the corresponding part number for what you need. Stan’s NoTubes offers two grades of
bearing: chrome steel (stock in Neo, Neo OS, and Neo CL) and stainless steel (stock in Neo S,
Neo Ultimate, and Neo Ultimate CL) - they are interchangeable.
Front* Rear Freehub** Chrome Steel Stainless Steel
Neo 6902 (x2) 6902 (x2) 15267 (x2) 6902 ZH0816 ZH0817
Neo OS 6804 (x2) 6902 (x2) 15267 (x2) 6804 ZH0818 ZH0819
Neo CL 6902 (x2) 6902 (x2) 15267 (x2) 6900 ZH0958 ZH0959
Neo Singlespeed 6902 (x2) 15267 (x2) 15267 ZH0814 ZH0815
Neo S 6902 (x2) 6902 (x2) 15267 (x2)
Neo S CL 6902 (x2) 6902 (x2) 15267 (x2)
Neo Ultimate 6902 (x2) 6902 (x2) 15267 (x2)
Neo Ultimate CL 6902 (x2) 6902 (x2) 15267 (x2)
Neo Ultimate Singlespeed 6902 (x2) 15267 (x2)
Table 4: Bearing Size and Quantity for Neo Series Hubs
* = While Notubes bearings are a standard size, they feature a
machined groove to aid in axle sleeve location and must be used in
Neo series front hubs (see section 3.2.3 for further detail)
** = All Neo series freehubs use the same bearings
Table 5: NoTubes Bearing Part Numbers*
* = All NoTubes bearings are sold in pairs.
Page 7
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
3 Maintenance Instructions
This chapter contains detailed instructions for servicing a Stan’s NoTubes Neo hub. This includes
end cap removal, axle and bearing removal, freehub service, as well as reassembly of the hub.
Careful adherence to these instructions is necessary to safely and reliably service a Neo hub.
3.1 Tools
Stan’s NoTubes Neo series hubs are designed to be user-friendly and require a bare minimum of
tools to service. Below is a list of what is needed to perform a complete service on a pair of Neo
hubs:
● Bench Vise
● Clean, lint free rags
● Dumonde Tech Freehub Grease (or similar light-weight grease)
● Park Tool AV-5 Aluminum Axle Vise Insert
● 15mm Sealed Bearing Extractor (such as Wheels Manufacturing 15mm Sealed Bearing
Extractor), and necessary tools
● ¼” or ⅜”, or similar, Punch
● Hammer
● Soft-Faced Mallet
● Bearing Press (such as Wheels Manufacturing Press-1) with necessary installation drifts
● A small flathead screwdriver
● Isopropyl Alcohol
● Toothbrush
● Clean rag
Page 8
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
3.2 Neo Front Hubs
Before performing maintenance service on a Stan’s NoTubes Neo hub, clean the exterior of the
hub in accordance with Section 1.4.
3.2.1 End Cap Removal/Replacement
1. Remove end caps:
● For Quick Release End caps: Clamp one end cap in the 20mm slot of the Park Tool AV-5.
Gently oscillate the hub/wheel while lightly pulling upwards to unseat the cap. Repeat on
the other end cap.
For 15mm End cap: Clamp one end cap in the 20mm slot of the Park Tool AV-5. Gently rock the
hub/wheel toward you to unseat the cap. Repeat on the other end cap.
Page 9
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
2. Clean end caps before reinserting into the hub. (Note: Cleansing of the end cap seals should be
performed in accordance with Section 1.5 to prevent damaging them). Ensure that the SealLock
seals are positioned with their U-hook facing outwards from the hub body, as shown below.
Install end caps, taking care to not pinch or fold the SealLock seal
3.2.2 Front Hub Bearing Removal
1. Remove end caps from hub using the procedures found in Step 1 of “End Cap
Removal/Replacement
2. Insert 15mm Sealed Bearing Extractor into bearing and tighten with an open-end wrench. Tap
the extractor and bearing out of the hub shell using a hammer and punch. (Note: Perform this
step over a rag as the bearing, extractor, and inner axle sleeve will fall from the hub shell when
the bearing is removed.)
3. Remove the inner axle sleeve.
4. Repeat step 2 to remove second bearing.
Page 10
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
3.2.3 Front Hub Bearing Installation
1. Thoroughly clean hub shell bore, hub sleeve, and bearing exteriors with isopropyl alcohol and a
clean rag.
2. Apply thin layer of grease to the non-drive side bearing bore and the outer race of the bearing.
3. Arrange the hub shell, bearing press, a 6902 open bore drift, and one 6902 bearing as shown
below. (Note: Installing one bearing at a time ensures the bearing is installed straight).
4. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing
is fully seated in the hub shell (Note: Overtightening can result in bearing damage).
5. Apply thin layer of grease to the drive side bearing bore and the outer race of the bearing.
6. With the hub axis oriented vertically, insert the inner axle sleeve. Note: The axle sleeve has a lip
on one end. Insert axle sleeve lip-side down to locate in the groove on the bearing’s inner race.
(Continued on next)
Page 11
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
7. Arrange the hub, bearing press, bearing drifts, and one 6902 bearing as shown below.
(Note: It is very important to keep the hub vertical and steady for this step. If the sleeve
dislocates, it may damage the lips of the axle sleeve upon installation of the second bearing).
8. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing
is fully seated in the hub shell (Note: overtightening can result in bearing damage).
Page 12
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
3.3 Neo Rear Hubs
Before performing maintenance service on a Stan’s NoTubes Neo hub, clean the exterior of the
hub in accordance with Section 1.4.
3.3.1 General Maintenance Disassembly
1. Remove end caps:
Remove non-drive (disc side) endcap. Neo series endcaps are designed to be removed by
hand. Should the endcap not come off easily (this is common with a brand-new, never
disassembled hub) an axle vise may be needed.
Page 13
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
Remove axle and drive-side endcap by hand. If the axle will not remove by hand, tap on the
exposed (non-drive) axle end with a soft-face hammer to dislodge.
2. Pull the freehub from the hub shell. Take care not to lose the small red spacer which sits
between the freehub body and the drive-side bearing.
3. Using a small flathead screw driver, gently remove the co-molded freehub seal from the hub
shell. Take care not to cut or pinch the edge of the seal.
3.3.2 General Maintenance Reassembly
1. Clean the drive ring, co-molded freehub seal, and freehub using isopropyl alcohol and a clean
toothbrush. Apply a light coating of Dumonde Tech Freehub Grease to the axle, drive ring, and
freehub pawls.
2. Install co-molded freehub seal into the groove adjacent to the drive ring in the hub shell.
3. Insert axle into hub.
4. Slide red spacer onto axle.
Page 14
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
5. Install freehub by sliding onto the axle and twisting counter-clockwise to allow the freehub
pawls to mesh with the drive ring. Take care not to cut the co-molded freehub seal.
6. Clean end caps with isopropyl alcohol, a toothbrush, and a clean rag.
7. Gently press end caps onto axle by hand (the flanged end cap goes on the non-drive side) . Take
care not to pinch the o-ring inside each end cap as well as the v-seal on the non-drive side end
cap
Page 15
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
3.3.3 Rear Hub Bearing Removal
1. Disassemble hub by methods outlined in section 3.3.1 General Maintenance Disassembly.
2. Install 15mm Sealed Bearing Extractor into one of the bearings. Tap Extractor and bearing out of hub
shell using punch and hammer, as shown in below. (Note: Perform this step over a rag as the
bearing, extractor, and inner axle sleeve will fall from the hub shell when the bearing is removed.
3. Repeat step 2 to remove second bearing.
3.3.4 Rear Hub Bearing Installation
1. Thoroughly clean hub shell bore, hub sleeve, and bearing exteriors with isopropyl alcohol and a
clean rag.
2. Apply thin layer of grease to the non-drive side bearing bore.
3. Arrange the hub shell, bearing press, a pair of 6902 open bore drifts, and one 6902 bearing as
shown below. (Note: Installing one bearing at a time ensures the bearing is installed straight)
Page 16
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
4. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing
is fully seated in the hub shell. Note: Over-tightening can result in bearing damage.
5. Insert inner axle sleeve.
6. Arrange the hub shell, bearing press, drifts, and the second 6902 bearing as shown below.
7. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing
is fully seated in the hub shell. (Note: Over-tightening can result in bearing damage.)
3.3.5 Freehub Pawl & Spring Removal/Installation
1. Using a small flathead screw driver, pry the pawl retaining ring off of the freehub body.
2. Slide the pawls, and then pawl springs, out of their respective pockets in the freehub body.
3. Thoroughly clean the pawls, pawls springs, and pawl pockets in the freehub body with isopropyl
alcohol, a toothbrush, and a clean rag.
Page 17
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
4. Reassemble the freehub by first installing the pawl springs, and then the pawls. See below for
proper arrangement. (Note: In order to ensure proper freehub function, take care not to deform
pawl springs during installation.)
5. Install the pawl retaining ring into its groove in the freehub body.
Insert photo showing pawl retaining ring install.
3.3.6 Freehub Bearing Removal
1. Remove the pawl retaining ring, pawls, and pawl springs from the freehub body by methods
outlined in Section 3.3.5 Freehub Pawl & Spring Removal/Installation.
2. Remove the rubber seal adjacent to the outboard bearing with a small flathead screwdriver
Page 18
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
3. Insert 15mm Sealed Bearing Extractor into one of the freehub bearings. Tap Extractor and
bearing out of hub shell using punch and hammer, as shown in the following image. (Note:
Perform this step over a rag as the bearing, extractor, and inner axle sleeve will fall from the hub
shell when the bearing is removed.)
4. Install 15mm Sealed Bearing Extractor in the second bearing. Tap Extractor and bearing out of
hub shell using punch and hammer.
3.3.7 Freehub Bearing Installation
1. Thoroughly clean freehub body bore, freehub sleeve, and bearing exteriors with isopropyl
alcohol and a clean rag.
2. Apply thin layer of grease to the outboard bearing bore.
3. Arrange the freehub body, bearing press, 15267 open bore drifts, and one 15267 bearing as
shown below. (Note: Installing one bearing at a time ensures the bearing is installed straight).
Page 19
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
4. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing
is fully seated in the hub shell. (Note: Over-tightening can result in bearing damage.)
5. Apply thin layer of grease to the inboard bearing bore.
6. Insert inner axle sleeve.
7. Arrange the freehub, bearing press, drifts, and the second 15267 bearing as shown below:
8. Turn the handle counter-clockwise to press the bearing into the hub until it is hand-tight and the
bearing is fully seated in the hub shell. (Note: Over-tightening can result in bearing damage.)
Note: Small grooves and burrs from the cassette's contact with the freehub will not affect hub
performance, and can be gently filed down to allow easier cassette installation. (Note: Only light filing is
needed; take care not to remove more material than necessary.)
Page 20
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
3.4 Front OS Hubs
Before performing maintenance service on a Stan’s NoTubes Neo hub, clean the exterior of the
hub in accordance with Section 1.4.
Additional Tools Required:
● 20mm Sealed Bearing Extractor, and necessary tools
3.4.1 OS End Cap Removal/Replacement
3. Remove end caps:
● For Quick Release End caps: Clamp one end cap in the 20mm slot of the Park Tool AV-5.
Oscillate the hub/wheel while lightly pulling upwards to unseat the cap. Repeat on the other
end cap.
● For 15mm End caps: Clamp one end cap in the 20mm slot of the Park Tool AV-5. Oscillate
the hub/wheel while lightly pulling upwards to unseat the cap. Repeat on the other end cap.
● For 20mm End cap: Clamp one end cap in the 25mm slot of the Park Tool AV-5. Gently rock
the hub/wheel toward you to unseat the cap. Repeat on the other end cap.
4. Clean end caps before reinserting into the hub. Note: Cleansing of the end cap seals should be
performed in accordance with Section 1.5 to prevent damaging them. Ensure that the SealLock
seals are positioned with their U-hook facing outwards from the hub body, as shown below.
5. To reinstall, press end caps in by hand. (Note: Take care to not pinch or fold the SealLock seal.)
Page 21
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
3.4.2 OS Front Hub Bearing Removal
1. Remove end caps from hub using the procedures found in Step 1 of “End Cap
Removal/Replacement”
2. Install 20mm Sealed Bearing Extractor into one of the bearings. Tap Extractor and bearing out of
hub shell using punch and hammer, as shown below. (Note: Perform this step over a rag as the
bearing, extractor, and inner axle sleeve will fall from the hub shell when the bearing is
removed.)
3. Repeat step 2 to remove second bearing.
Page 22
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
3.4.3 OS Front Hub Bearing Installation
1. Thoroughly clean hub shell bore, hub sleeve, and bearing exteriors with isopropyl alcohol and a
clean rag.
2. Apply thin layer of grease to the non-drive side bearing bore.
3. Arrange the hub shell, bearing press, a 6804 open bore drift, and one 6804 bearing as shown
below. (Note: Installing one bearing at a time ensures the bearing is installed straight).
4. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing
is fully seated in the hub shell (note: overtightening can result in bearing damage).
5. Apply thin layer of grease to the drive side bearing bore and the outer race of the bearing.
6. With the hub axis oriented vertically, insert the inner axle sleeve. Note: The axle sleeve has a lip
on each end which aligns it with the inner bearing races.
(Continued on next)
Page 23
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
7. Arrange the hub, bearing press, bearing drifts, and the second 6804 bearing as shown below.
Note: Hold the hub steady to maintain the centralized location of the inner axle sleeve. If the
sleeve dislocates, it may damage the lips of the axle sleeve upon installation of the second
bearing.
8. Turn the handle clockwise to press the bearing into the hub until it is hand-tight and the bearing
is fully seated in the hub shell (Note: overtightening can result in bearing damage).
Page 24
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
3
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
21.5 33.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0771
KIT, NEO, END CAPS, FRONT, 15MM TA
E01
*
ZH0772
KIT, NEO, END CAPS, FRONT, 9MM QR
E04
*
ZH0773
KIT, NEO, END CAPS, FRONT, 9MM TA
E03
*
ZH0774
KIT, NEO, END CAPS, FRONT, 12MM TA
E02
*
ZH0985
KIT, NEO, END CAPS, FRONT, TORQUE CAP
E28
2
ZH0792
KIT, NEO, AXLE SPACER, FRONT, 15/9X100, STD
S09
3
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
*
ZH0816
KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, FRONT, STANS, NEO, 6B, 15X100, TA
Page 25
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
3
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 44.5
CTR TO FLANGE (mm)
28
40.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0771
KIT, NEO, END CAPS, FRONT, 15MM TA
E01
*
ZH0772
KIT, NEO, END CAPS, FRONT, 9MM QR
E04
*
ZH0773
KIT, NEO, END CAPS, FRONT, 9MM TA
E03
*
ZH0774
KIT, NEO, END CAPS, FRONT, 12MM TA
E02
*
ZH0985
KIT, NEO, END CAPS, FRONT, TORQUE CAP
E28
2
ZH0794
KIT, NEO, AXLE SPACER, FRONT, 15X110, STD
S11
3
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
*
ZH0816
KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, FRONT, STANS, NEO, 6B, 15X110, TA
Page 26
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
3
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
21.5 33.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0953
KIT, NEO, END CAPS, FRONT, 15MM TA, CL
E20
*
ZH0954
KIT, NEO, END CAPS, FRONT, 9MM QR, CL
E21
*
ZH0986
KIT, NEO, END CAPS, FRONT, 9MM TA, CL
E26
*
ZH0955
KIT, NEO, END CAPS, FRONT, 12MM TA, CL
E22
2
ZH0991
KIT, NEO, AXLE SPACER, FRONT, 15X110, STD, CL
S17
3
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
*
ZH0816
KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, FRONT, STANS, NEO, CL, 15X100, TA
Page 27
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
3
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 45.5
CTR TO FLANGE (mm)
22.0 35.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0771
KIT, NEO, END CAPS, FRONT, 15MM TA
E01
*
ZH0772
KIT, NEO, END CAPS, FRONT, 9MM QR
E04
*
ZH0773
KIT, NEO, END CAPS, FRONT, 9MM TA
E03
*
ZH0774
KIT, NEO, END CAPS, FRONT, 12MM TA
E02
*
ZH0985
KIT, NEO, END CAPS, FRONT, TORQUE CAP
E28
2
ZH0793
KIT, NEO, AXLE SPACER, FRONT, 15/9X100, LTE
S10
3
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, FRONT, STANS, NEO ULT, 6B, 15X100, TA
Page 28
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
3
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 45.5
CTR TO FLANGE (mm)
28
40.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0771
KIT, NEO, END CAPS, FRONT, 15MM TA
E01
*
ZH0772
KIT, NEO, END CAPS, FRONT, 9MM QR
E04
*
ZH0773
KIT, NEO, END CAPS, FRONT, 9MM TA
E03
*
ZH0774
KIT, NEO, END CAPS, FRONT, 12MM TA
E02
*
ZH0985
KIT, NEO, END CAPS, FRONT, TORQUE CAP
E28
2
ZH0795
KIT, NEO, AXLE SPACER, FRONT, 15X110, LTE
S12
3
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, FRONT, STANS, NEO ULT, 6B, 15X110, TA
Page 29
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
3
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 45.5
CTR TO FLANGE (mm)
22.0 35.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0953
KIT, NEO, END CAPS, FRONT, 15MM TA, CL
E20
*
ZH0954
KIT, NEO, END CAPS, FRONT, 9MM QR, CL
E21
*
ZH0986
KIT, NEO, END CAPS, FRONT, 9MM TA, CL
E26
*
ZH0955
KIT, NEO, END CAPS, FRONT, 12MM TA, CL
E22
2
ZH0989
KIT, NEO, AXLE SPACER, FRONT, 15X110, LTE, CL
S18
3
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, FRONT, STANS, NEO ULTIMATE, CL, 15X100, TA
Page 30
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
3
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
27.5 38.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0776
KIT, NEO OS, END CAPS, FRONT, 15MM TA
E06
*
ZH0777
KIT, NEO OS, END CAPS, FRONT, 9MM QR
E07
*
ZH0983
KIT, NEO OS, END CAPS, FRONT, 12MM TA
E25
*
ZH0775
KIT, NEO OS, END CAPS, FRONT, 20MM TA
E05
*
ZH0984
KIT, NEO OS, END CAPS, FRONT, TORQUE CAP
E29
*
ZH0982
KIT, NEO OS, END CAPS, FRONT, 9MM TA
E24
2
ZH0990
KIT, NEO OS, AXLE SPACER, FRONT, 15X110, STD
S16
3
ZH0818
KIT, BEARING, #6804, 20X32X7MM, CHROME (GRAY) 2PC
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, FRONT, STANS, NEO, 6B, 15X110, OS, TA
Page 31
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
3
2
5
5
4
6
4
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
34.5 18.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0779
KIT, NEO, END CAPS, REAR, 12X142/148/157 TA
E15,E16
*
ZH0778
KIT, NEO, END CAPS, REAR, 12X135/150 TA
E13,E14
*
ZH0780
KIT, NEO, END CAPS, REAR, 10X135 QR
E11,E12
*
ZH0781
KIT, NEO, END CAPS, REAR, 10X135 TA
E09,E10
*
ZH0769
KIT, NEO, CONVERSION, REAR, QR END CAPS AND 135MM LEVER
E11,E12
*
ZH0770
KIT, NEO, CONVERSION, REAR, BO END CAPS, AXLE, AND BOLTS
-
2
ZH0782
KIT, NEO, AXLE, REAR, 12X135/142 & SINGLESPEED
A01
3
ZH0786
KIT, NEO, AXLE SPACER, REAR, 12X135/142 , STD
S01
*
ZH0787
KIT, NEO, AXLE SPACER, REAR, 12X135/142 , LTE
S02
4
ZH0805
KIT, NEO, FREEHUB, 4-PAWL, SHIMANO (BLACK)
-
*
ZH0806
KIT, NEO, FREEHUB, 4-PAWL, SRAM XD (BLACK)
-
5
ZH0816
KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC
-
*
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
-
6
ZH0802
KIT, NEO, CASSETTE SPACER, 10SP (SILVER)
-
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
**
ZH0799
KIT, NEO, FREEHUB SEALS
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, REAR, STANS, NEO, 6B, 12x142, TA
Page 32
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
44
5
5
6
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
37.5 23.0
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0779
KIT, NEO, END CAPS, REAR, 12X142/148/157 TA
E15,E16
*
ZH0778
KIT, NEO, END CAPS, REAR, 12X135/150 TA
E13,E14
*
ZH0780
KIT, NEO, END CAPS, REAR, 10X135 QR
E11,E12
*
ZH0781
KIT, NEO, END CAPS, REAR, 10X135 TA
E09,E10
2
ZH0783
KIT, NEO, AXLE, REAR, 12X148
A02
3
ZH0788
KIT, NEO, AXLE SPACER, REAR, 12X148, STD
S03
4
ZH0805
KIT, NEO, FREEHUB, 4-PAWL, SHIMANO (BLACK)
*
ZH0806
KIT, NEO, FREEHUB, 4-PAWL, SRAM XD (BLACK)
*
ZH0808
KIT, NEO, FREEHUB, 4-PAWL, CAMPY (BLACK)
5
ZH0816
KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC
*
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
6
ZH0802
KIT, NEO, CASSETTE SPACER, 10SP (SILVER)
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
**
ZH0799
KIT, NEO, FREEHUB SEALS
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, REAR, STANS, NEO, 6B, 12x148, TA
Page 33
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
44
5
5
6
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
42.0 26.0
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0779
KIT, NEO, END CAPS, REAR, 12X142/148/157 TA
E15,E16
*
ZH0778
KIT, NEO, END CAPS, REAR, 12X135/150 TA
E13,E14
*
ZH0781
KIT, NEO, END CAPS, REAR, 10X135 TA
E09,E10
2
ZH0784
KIT, NEO, AXLE, REAR, 12X150/157
A03
3
ZH0790
KIT, NEO, AXLE SPACER, REAR, 12X150/157 & SINGLESPEED, STD
S05
4
ZH0805
KIT, NEO, FREEHUB, 4-PAWL, SHIMANO (BLACK)
*
ZH0806
KIT, NEO, FREEHUB, 4-PAWL, SRAM XD (BLACK)
*
ZH0808
KIT, NEO, FREEHUB, 4-PAWL, CAMPY (BLACK)
5
ZH0816
KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC
*
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
6
ZH0802
KIT, NEO, CASSETTE SPACER, 10SP (SILVER)
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
**
ZH0799
KIT, NEO, FREEHUB SEALS
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, REAR, STANS, NEO, 6B, 12x157, TA
Page 34
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
44
5
5
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
34.5 33.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0779
KIT, NEO, END CAPS, REAR, 12X142/148/157 TA
E15,E16
*
ZH0778
KIT, NEO, END CAPS, REAR, 12X135/150 TA
E13,E14
*
ZH0780
KIT, NEO, END CAPS, REAR, 10X135 QR
E11,E12
*
ZH0781
KIT, NEO, END CAPS, REAR, 10X135 TA
E09,E10
*
ZH0769
KIT, NEO, CONVERSION, REAR, QR END CAPS AND 135MM LEVER
E11,E12
*
ZH0770
KIT, NEO, CONVERSION, REAR, BO END CAPS, AXLE, AND BOLTS
2
ZH0782
KIT, NEO, AXLE, REAR, 12X135/142 & SINGLESPEED
A01
3
ZH0790
KIT, NEO, AXLE SPACER, REAR, 12X150/157 & SINGLESPEED, STD
S05
4
ZH0807
KIT, NEO, FREEHUB, 4-PAWL, SINGLESPEED (BLACK)
5
ZH0816
KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC
*
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
*
ZH0804
KIT, NEO, SINGLESPEED SPACER KIT
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
**
ZH0799
KIT, NEO, FREEHUB SEALS
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, REAR, STANS, NEO, 6B, 12x142, TA, SS
Page 35
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
4
5
5
6
4
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
33.5 18.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0956
KIT, NEO, END CAPS, REAR, 12X142/148/157 TA, CL
E19,E16
*
ZH0988
KIT, NEO, END CAPS, REAR, 12X135/150 TA, CL
E18,E14
*
ZH0957
KIT, NEO, END CAPS, REAR, 10X135 QR, CL
E17,E12
*
ZH0987
KIT, NEO, END CAPS, REAR, 10X135 TA, CL
E27,E10
*
ZH0962
KIT, NEO, CONVERSION, REAR, QR END CAPS AND 135MM LEVER, CL
E17,E12
*
ZH0770
KIT, NEO, CONVERSION, REAR, BO END CAPS, AXLE, AND BOLTS
2
ZH0782
KIT, NEO, AXLE, REAR, 12X135/142 & SINGLESPEED
A01
3
ZH0995
KIT, NEO, AXLE SPACER, REAR, 12X135/142 , STD, CL
S21
4
ZH0805
KIT, NEO, FREEHUB, 4-PAWL, SHIMANO (BLACK)
*
ZH0806
KIT, NEO, FREEHUB, 4-PAWL, SRAM XD (BLACK)
*
ZH0808
KIT, NEO, FREEHUB, 4-PAWL, CAMPY (BLACK)
5
ZH0816
KIT, BEARING, #6902,15X28X7MM, CHROME (GRAY) 2PC
*
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
6
ZH0802
KIT, NEO, CASSETTE SPACER, 10SP (SILVER)
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
**
ZH0799
KIT, NEO, FREEHUB SEALS
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, REAR, STANS, NEO, CL, 12x142, TA
Page 36
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
44
5
5
6
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
33.5 18.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0779
KIT, NEO, END CAPS, REAR, 12X142/148/157 TA
E15,E16
*
ZH0778
KIT, NEO, END CAPS, REAR, 12X135/150 TA
E13,E14
*
ZH0780
KIT, NEO, END CAPS, REAR, 10X135 QR
E11,E12
*
ZH0781
KIT, NEO, END CAPS, REAR, 10X135 TA
E09,E10
*
ZH0769
KIT, NEO, CONVERSION, REAR, QR END CAPS AND 135MM LEVER
E11,E12
*
ZH0770
KIT, NEO, CONVERSION, REAR, BO END CAPS, AXLE, AND BOLTS
2
ZH0782
KIT, NEO, AXLE, REAR, 12X135/142 & SINGLESPEED
A01
3
ZH0787
KIT, NEO, AXLE SPACER, REAR, 12X135/142 , LTE
S02
4
ZH0809
KIT, NEO, FREEHUB, 6-PAWL, SHIMANO (GRAY)
*
ZH0810
KIT, NEO, FREEHUB, 6-PAWL, SRAM XD (GRAY)
*
ZH0812
KIT, NEO, FREEHUB, 6-PAWL, CAMPY (GRAY)
5
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
6
ZH0802
KIT, NEO, CASSETTE SPACER, 10SP (SILVER)
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
**
ZH0799
KIT, NEO, FREEHUB SEALS
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, REAR, STANS, NEO ULT, 6B, 12x142, TA
Page 37
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
44
5
5
6
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
37.5 23.0
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0779
KIT, NEO, END CAPS, REAR, 12X142/148/157 TA
E15,E16
*
ZH0778
KIT, NEO, END CAPS, REAR, 12X135/150 TA
E13,E14
*
ZH0780
KIT, NEO, END CAPS, REAR, 10X135 QR
E11,E12
*
ZH0781
KIT, NEO, END CAPS, REAR, 10X135 TA
E09,E10
2
ZH0783
KIT, NEO, AXLE, REAR, 12X148
A02
3
ZH0789
KIT, NEO, AXLE SPACER, REAR, 12X148, LTE
S04
4
ZH0809
KIT, NEO, FREEHUB, 6-PAWL, SHIMANO (GRAY)
*
ZH0810
KIT, NEO, FREEHUB, 6-PAWL, SRAM XD (GRAY)
*
ZH0812
KIT, NEO, FREEHUB, 6-PAWL, CAMPY (GRAY)
5
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
6
ZH0802
KIT, NEO, CASSETTE SPACER, 10SP (SILVER)
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
**
ZH0799
KIT, NEO, FREEHUB SEALS
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, REAR, STANS, NEO ULT, 6B, 12x148, TA
Page 38
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
44
5
5
6
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
42.0 26.0
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0779
KIT, NEO, END CAPS, REAR, 12X142/148/157 TA
E15,E16
*
ZH0778
KIT, NEO, END CAPS, REAR, 12X135/150 TA
E13,E14
*
ZH0781
KIT, NEO, END CAPS, REAR, 10X135 TA
E09,E10
2
ZH0784
KIT, NEO, AXLE, REAR, 12X150/157
A03
3
ZH0992
KIT, NEO, AXLE SPACER, REAR, 12X150/157 & SINGLESPEED, LTE
S06
4
ZH0809
KIT, NEO, FREEHUB, 6-PAWL, SHIMANO (GRAY)
*
ZH0810
KIT, NEO, FREEHUB, 6-PAWL, SRAM XD (GRAY)
*
ZH0812
KIT, NEO, FREEHUB, 6-PAWL, CAMPY (GRAY)
5
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
6
ZH0802
KIT, NEO, CASSETTE SPACER, 10SP (SILVER)
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
**
ZH0799
KIT, NEO, FREEHUB SEALS
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, REAR, STANS, NEO ULT, 6B, 12x157, TA
Page 39
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
4
4
5
5
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
34.5 33.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0779
KIT, NEO, END CAPS, REAR, 12X142/148/157 TA
E15,E16
*
ZH0778
KIT, NEO, END CAPS, REAR, 12X135/150 TA
E13,E14
*
ZH0780
KIT, NEO, END CAPS, REAR, 10X135 QR
E11,E12
*
ZH0781
KIT, NEO, END CAPS, REAR, 10X135 TA
E09,E10
*
ZH0769
KIT, NEO, CONVERSION, REAR, QR END CAPS AND 135MM LEVER
E11,E12
*
ZH0770
KIT, NEO, CONVERSION, REAR, BO END CAPS, AXLE, AND BOLTS
2
ZH0782
KIT, NEO, AXLE, REAR, 12X135/142 & SINGLESPEED
A01
3
ZH0992
KIT, NEO, AXLE SPACER, REAR, 12X150/157 & SINGLESPEED, LTE
S06
4
ZH0811
KIT, NEO, FREEHUB, 6-PAWL, SINGLESPEED (GRAY)
5
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
*
ZH0804
KIT, NEO, SINGLESPEED SPACER KIT
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
**
ZH0799
KIT, NEO, FREEHUB SEALS
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, REAR, STANS, NEO ULT, 6B, 12x142, TA, SS
Page 40
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
1
2
3
44
5
5
6
LEFT(DISC)
RIGHT(DRIVE)
FLANGE
(mm)
55.5 55.5
CTR TO FLANGE (mm)
33.5 18.5
#
KIT #
KIT DESCRIPTION
KIT CONTENTS
1
ZH0956
KIT, NEO, END CAPS, REAR, 12X142/148/157 TA, CL
E19,E16
*
ZH0988
KIT, NEO, END CAPS, REAR, 12X135/150 TA, CL
E18,E14
*
ZH0957
KIT, NEO, END CAPS, REAR, 10X135 QR, CL
E17,E12
*
ZH0987
KIT, NEO, END CAPS, REAR, 10X135 TA, CL
E27,E10
*
ZH0962
KIT, NEO, CONVERSION, REAR, QR END CAPS AND 135MM LEVER, CL
E17,E12
*
ZH0770
KIT, NEO, CONVERSION, REAR, BO END CAPS, AXLE, AND BOLTS
2
ZH0782
KIT, NEO, AXLE, REAR, 12X135/142 & SINGLESPEED
A01
3
ZH0994
KIT, NEO, AXLE SPACER, REAR, 12X135/142 , LTE, CL
S22
4
ZH0809
KIT, NEO, FREEHUB, 6-PAWL, SHIMANO (GRAY)
*
ZH0810
KIT, NEO, FREEHUB, 6-PAWL, SRAM XD (GRAY)
*
ZH0812
KIT, NEO, FREEHUB, 6-PAWL, CAMPY (GRAY)
5
ZH0817
KIT, BEARING, #6902,15X28X7MM, STAINLESS (ORANGE) 2PC
6
ZH0802
KIT, NEO, CASSETTE SPACER, 10SP (SILVER)
**
ZH0813
KIT, NEO, END CAP SEALS, FRONT AND REAR
**
ZH0799
KIT, NEO, FREEHUB SEALS
* denotes optional hub configuration
**includes seals for all configurations
2 1
A
B
A
B
12
HUB, REAR, STANS, NEO ULTIMATE, CL, 12x142, TA
Page 41
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
2
3
3 4
4
1
#
KIT #
KIT DESCRIPTION
1
ZH0800
KIT, NEO, SPRING AND PAWL 6PC
2
ZH0798
KIT, NEO, FREEHUB SPACER (RED)
3
ZH0814
KIT, BEARING, #15267, 15X26X7MM, CHROME (GRAY) 2PC
*
ZH0815
KIT, BEARING, #15267, 15X26X7MM, STAINLESS (ORANGE) 2PC
4
ZH0799
KIT, NEO, FREEHUB SEALS (BLACK)
* denotes optional hub configuration
2 1
A
B
A
B
12
FREEHUB, STANS, NEO, 4-PAWL, SHIMANO
Page 42
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
2
3
34
4
1
#
KIT #
KIT DESCRIPTION
1
ZH0800
KIT, NEO, SPRING AND PAWL 6PC
2
ZH0798
KIT, NEO, FREEHUB SPACER (RED)
3
ZH0814
KIT, BEARING, #15267, 15X26X7MM, CHROME (GRAY) 2PC
*
ZH0815
KIT, BEARING, #15267, 15X26X7MM, STAINLESS (ORANGE) 2PC
4
ZH0799
KIT, NEO, FREEHUB SEALS (BLACK)
* denotes optional hub configuration
2 1
A
B
A
B
12
FREEHUB, STANS, NEO, 4-PAWL, SRAM XD
Page 43
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
2
3
3
4
4
5
1
#
KIT #
KIT DESCRIPTION
1
ZH0800
KIT, NEO, SPRING AND PAWL 6PC
2
ZH0798
KIT, NEO, FREEHUB SPACER (RED)
3
ZH0814
KIT, BEARING, #15267, 15X26X7MM, CHROME (GRAY) 2PC
*
ZH0815
KIT, BEARING, #15267, 15X26X7MM, STAINLESS (ORANGE) 2PC
4
ZH0799
KIT, NEO, FREEHUB SEALS (BLACK)
5
ZH0803
KIT, NEO, SINGLESPEED LOCKRING
*
ZH0804
KIT, NEO, SINGLESPEED SPACER KIT
* denotes optional hub configuration
2 1
A
B
A
B
12
FREEHUB, STANS, NEO, 4-PAWL, SINGLESPEED
Page 44
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
2
3
34
4
1
#
KIT #
KIT DESCRIPTION
1
ZH0800
KIT, NEO, SPRING AND PAWL 6PC
2
ZH0798
KIT, NEO, FREEHUB SPACER (RED)
*
ZH0814
KIT, BEARING, #15267, 15X26X7MM, CHROME (GRAY) 2PC
3
ZH0815
KIT, BEARING, #15267, 15X26X7MM, STAINLESS (ORANGE) 2PC
4
ZH0799
KIT, NEO, FREEHUB SEALS (BLACK)
* denotes optional hub configuration
2 1
A
B
A
B
12
FREEHUB, STANS, NEO, 6-PAWL, SHIMANO
Page 45
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
2
3
3
4
4
1
#
KIT #
KIT DESCRIPTION
1
ZH0800
KIT, NEO, SPRING AND PAWL 6PC
2
ZH0798
KIT, NEO, FREEHUB SPACER (RED)
*
ZH0814
KIT, BEARING, #15267, 15X26X7MM, CHROME (GRAY) 2PC
3
ZH0815
KIT, BEARING, #15267, 15X26X7MM, STAINLESS (ORANGE) 2PC
4
ZH0799
KIT, NEO, FREEHUB SEALS (BLACK)
* denotes optional hub configuration
2 1
A
B
A
B
12
FREEHUB, STANS, NEO, 6-PAWL, SRAM XD
Page 46
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL
1
2
3
3
4
4
5
1
#
KIT #
KIT DESCRIPTION
1
ZH0800
KIT, NEO, SPRING AND PAWL 6PC
2
ZH0798
KIT, NEO, FREEHUB SPACER (RED)
3
ZH0814
KIT, BEARING, #15267, 15X26X7MM, CHROME (GRAY) 2PC
*
ZH0815
KIT, BEARING, #15267, 15X26X7MM, STAINLESS (ORANGE) 2PC
4
ZH0799
KIT, NEO, FREEHUB SEALS (BLACK)
5
ZH0803
KIT, NEO, SINGLESPEED LOCKRING
*
ZH0804
KIT, NEO, SINGLESPEED SPACER KIT
* denotes optional hub configuration
2 1
A
B
A
B
12
FREEHUB, STANS, NEO, 6-PAWL, SINGLESPEED
Page 47
EIS-010 NEO INTERACTIVE HUB SERIES MANUAL

Navigation menu