Copley Controls Corp Step Net Panel Manual
StepNet_panel_Manual
User Manual: StepNet panel Manual
Open the PDF directly: View PDF 
.
Page Count: 190
| Download | |
| Open PDF In Browser | View PDF |
Stepnet™ Panel Amplifier User Guide P/N CC95-00294-000 Revision A June 2009 Stepnet Panel Amplifier User Guide TABLE OF CONTENTS About This Manual ................................................................................................................................................................................ 5 1: Introduction ................................................................................................................................................................................. 9 1.1: Amplifier ............................................................................................................................................................................... 10 1.2: Amplifier Commissioning with CME 2 ................................................................................................................................... 11 1.3: CANopen for Distributed Control........................................................................................................................................... 11 2: Operational Theory.................................................................................................................................................................... 13 2.1: Amplifier Power: Stepnet Panel (STP) .................................................................................................................................. 14 2.2: Amplifier Power: Stepnet Panel AC (STX) ............................................................................................................................ 15 2.3: Stepper Mode Operation....................................................................................................................................................... 16 2.4: Servo Mode Operation.......................................................................................................................................................... 18 2.5: Input Command Types ......................................................................................................................................................... 25 2.6: Communication .................................................................................................................................................................... 30 2.7: Limit Switches ...................................................................................................................................................................... 33 2.8: Brake Operation ................................................................................................................................................................... 34 2.9: Status Indicators................................................................................................................................................................... 35 2.10: Protection ........................................................................................................................................................................... 37 2.11: Position and Servo Velocity Errors...................................................................................................................................... 39 2.12: Inputs ................................................................................................................................................................................. 42 2.13: Outputs............................................................................................................................................................................... 42 3: Specifications ............................................................................................................................................................................ 43 3.1: Agency Approvals................................................................................................................................................................. 44 3.2: Power Input .......................................................................................................................................................................... 44 3.3: Power Output........................................................................................................................................................................ 45 3.4: Control Loops ....................................................................................................................................................................... 46 3.5: Stepnet Panel AC (STX) Internal Regen Circuit.................................................................................................................... 46 3.6: Digital Command Input ......................................................................................................................................................... 46 3.7: Stepnet Panel AC (STX) Analog Command Input................................................................................................................. 47 3.8: Digital Inputs......................................................................................................................................................................... 47 3.9: Digital Outputs...................................................................................................................................................................... 49 3.10: Encoder Power Supply Output............................................................................................................................................ 49 3.11: Incremental Quadrature Encoder Inputs ............................................................................................................................. 50 3.12: Stepnet Panel AC (STX) Multi-Mode Port ........................................................................................................................... 51 3.13: Serial Interface ................................................................................................................................................................... 51 3.14: CAN Interface ..................................................................................................................................................................... 51 3.15: Status Indicators................................................................................................................................................................. 52 3.16: Fault Levels ........................................................................................................................................................................ 52 3.17: Power Dissipation ............................................................................................................................................................... 52 3.18: Thermal Impedance............................................................................................................................................................ 52 3.19: Mechanical and Environmental ........................................................................................................................................... 53 3.20: Dimensions......................................................................................................................................................................... 54 4: Wiring......................................................................................................................................................................................... 57 4.1: Stepnet Panel (STP) Wiring.................................................................................................................................................. 58 4.2: Stepnet Panel AC (STX) Wiring............................................................................................................................................ 67 5: Mode Selection and General Setup.......................................................................................................................................... 85 5.1: Warnings .............................................................................................................................................................................. 86 5.2: CME 2 Installation and Serial Port Setup.............................................................................................................................. 87 5.3: Prerequisites ........................................................................................................................................................................ 91 5.4: Basic Setup .......................................................................................................................................................................... 93 5.5: Motor Setup.......................................................................................................................................................................... 95 5.6: Amplifier Configuration ....................................................................................................................................................... 100 5.7: Command Input.................................................................................................................................................................. 110 6: Stepper Mode Phase and Tune............................................................................................................................................... 115 6.1: Auto Phase (Stepper Mode) ............................................................................................................................................... 116 6.2: Position Limits (Stepper Mode with Encoder) ..................................................................................................................... 120 6.3: Current Loop....................................................................................................................................................................... 122 6.4: Profile Move Tests.............................................................................................................................................................. 125 6.5: Encoder Correction............................................................................................................................................................. 128 6.6: Completion Steps ............................................................................................................................................................... 129 7: Servo Mode Phase and Tune.................................................................................................................................................. 131 7.1: Auto Phase (Servo Mode)................................................................................................................................................... 132 7.2: Current Loop....................................................................................................................................................................... 136 7.3: Velocity Loop...................................................................................................................................................................... 139 7.4: Position Loop...................................................................................................................................................................... 141 7.5: Completion Steps ............................................................................................................................................................... 148 8: Using CME 2 (Stepper or Servo Mode) .................................................................................................................................. 149 8.1: CME 2 Overview................................................................................................................................................................. 150 8.2: Manage Amplifier and Motor Data ...................................................................................................................................... 154 8.3: Downloading Firmware ....................................................................................................................................................... 157 8.4: Control Panel...................................................................................................................................................................... 159 8.5: Home Function ................................................................................................................................................................... 164 Copley Controls Corp. 3 Table of Contents A: C: D: E: 4 Stepnet Panel Amplifier User Guide I2T Time Limit Algorithm ......................................................................................................................................................... 167 A.1: I2T Algorithm ...................................................................................................................................................................... 168 A.2: I2T Scope Trace Variables (STX Only) ............................................................................................................................... 172 Thermal Considerations.......................................................................................................................................................... 173 C.1: Operating Temperature and Cooling Configurations .......................................................................................................... 174 C.2: Heatsink Mounting Instructions .......................................................................................................................................... 179 Detent Compensation Gain..................................................................................................................................................... 181 D.1: Detent Gain Tuning ............................................................................................................................................................ 182 Ordering Guide and Accessories ........................................................................................................................................... 185 E.1: Stepnet Panel (STP) Amplifier ........................................................................................................................................... 186 E.2: Stepnet Panel AC (STX) Amplifier...................................................................................................................................... 187 E.3: Stepnet Module (STM) Amplifier ........................................................................................................................................ 188 E.4: Stepnet Micro Module (STL) Amplifier................................................................................................................................ 189 Copley Controls ABOUT THIS MANUAL Overview and Scope This manual describes the operation and installation of the Stepnet Panel (STP) and Stepnet Panel AC (STX) amplifiers manufactured by Copley Controls. The material in this manual applies to the entire Stepnet amplifier family with the exception of the specifications and wiring diagrams. For specifications and wiring information on the Stepnet Module and Stepnet Micro Module, refer to the appropriate data sheets. Related Documentation See the Stepnet data sheets at http://www.copleycontrols.com/Motion/Downloads/stepnetData.html Choose the appropriate data sheet. Related Copley Controls manuals include: • CME 2 User Guide • CANopen Programmer’s Manual • Copley Motion C++ Libraries (CML) Reference Manual (license purchase required) • Copley Motion Objects (CMO) Programmer’s Guide • Copley Camming User Guide • Copley ASCII Interface Programmer’s Guide • Copley DeviceNet Programmer’s Guide • Copley Amplifier Parameter Dictionary Information on Copley Controls Software can be found at: http://www.copleycontrols.com/Motion/Products/Software/index.html Comments Copley Controls welcomes your comments on this manual. See http://www.copleycontrols.com for contact information. Copyrights No part of this document may be reproduced in any form or by any means, electronic or mechanical, including photocopying, without express written permission of Copley Controls. Stepnet, STP, STX, CML, CMO, and CME 2 are registered trademarks of Copley Controls. Windows NT, 2000, XP, Vista, Visual Basic, and .NET are trademarks or registered trademarks of the Microsoft Corporation. LabVIEW is a registered trademark of National Instruments Corporation. Document Validity We reserve the right to modify our products. The information in this document is subject to change without notice and does not represent a commitment by Copley Controls. Copley Controls assumes no responsibility for any errors that may appear in this document. Copley Controls Corp. 5 About this Manual Stepnet Panel Amplifier User Guide Product Warnings Observe all relevant state, regional, and local safety regulations when installing and using Copley Controls amplifiers. For safety and to assure compliance with documented system data, only Copley Controls should perform repairs to amplifiers. ! DANGER: Hazardous voltages. Exercise caution when installing and adjusting Copley Controls amplifiers. Failure to heed this warning can cause equipment damage, injury, or death. DANGER DANGER: Risk of electric shock. High-voltage circuits are connected to DC or AC power. Failure to heed this warning can cause equipment damage, injury, or death. DANGER: Motor voltage rating. Be sure that the motor is rated for the voltage provided by the amplifier’s outputs. Failure to heed this warning can cause equipment damage, injury, or death. DANGER: Risk of unexpected motion with non-latched faults. After the cause of a non-latched fault is corrected, the amplifier re-enables the PWM output stage without operator intervention. In this case, motion may re-start unexpectedly. Configure faults as latched unless a specific situation calls for non-latched behavior. When using non-latched faults, be sure to safeguard against unexpected motion. Failure to heed this warning can cause equipment damage, injury, or death. DANGER: Using CME 2 can affect or suspend amplifier operations. Use of CME 2 to change amplifier parameters while operating the amplifier can affect operations in progress. Using CME 2 to initiate motion can cause operations to suspend. The operations may restart unexpectedly when the CME 2 move is stopped. Failure to heed this warning can cause equipment damage, injury, or death. DANGER: Latching an output does not eliminate the risk of unexpected motion with nonlatched faults. Associating a fault with a latched, custom-configured output does not latch the fault itself. After the cause of a non-latched fault is corrected, the amplifier re-enables without operator intervention. In this case, motion may re-start unexpectedly. For more information, see Clearing Non-Latched Faults (p. 37). Failure to heed this warning can cause equipment damage, injury, or death. 6 Copley Controls Stepnet Panel Amplifier User Guide ! About this Manual WARNING: Do not ground mains-connected circuits. With the exception of the ground pins on the STX connectors J1 and J2, all of the other circuits on these connectors are mains-connected and must never be grounded. Failure to heed this warning can cause equipment damage. WARNING WARNING: Do not plug or unplug connectors with power applied. The connecting or disconnecting of cables while the amplifier has 24Vdc and/or mains power applied is not recommended. Failure to heed this warning may cause equipment damage. Copley Controls Corp. 7 About this Manual Stepnet Panel Amplifier User Guide Revision History Revision Date 1.0 August 2004 Initial publication. 2.0 June 2005 Detent compensation gain feature. See Detent Compensation Gain (p. 181). 3 June 2008 17137 Updated Web page references. A June 2009 32822 Updated to include Stepnet Panel AC (STX) amplifiers. 8 ECO Comments Copley Controls CHAPTER 1: INTRODUCTION This chapter provides an overview of the Copley Controls Stepnet amplifier. Contents include: Title Page 1.1: Amplifier ............................................................................................................................................................................... 10 1.2: Amplifier Commissioning with CME 2 ................................................................................................................................... 11 1.3: CANopen for Distributed Control........................................................................................................................................... 11 Copley Controls Corp. 9 Introduction Stepnet Panel Amplifier User Guide 1.1: Amplifier Stepnet is a 100% digital stepping motor amplifier which can operate in two control modes, stepper or servo. In stepper mode, conventional microstepping techniques are used. In servo mode, stepping motors fitted with encoders can be operated as DC brushless servo motors in closed loop current, velocity or position modes. Stepnet can operate as a stand-alone amplifier or as a networked CANopen or DeviceNet node. It can also be controlled using the Copley ASCII interface over a serial connection. The multi-drop feature allows CME 2 or other ASCII serial controller to use an RS-232 serial connection to one amplifier as a gateway to other amplifiers linked together by CAN bus connections. The Stepnet can also be controlled by a Copley Virtual Machine (CVM) program running on the amplifier. Stepnet amplifiers can be networked with Copley Accelnet and Xenus digital servo amplifiers. When operating as a stand-alone amplifier, Stepnet can accept incremental position commands from step-motor controllers in Pulse and Direction or Count Up/Count Down formats, as well as A/B quadrature commands from a master-encoder. Pulse to motor position ratio is programmable for electronic gearing. In servo mode Stepnet can also accept PWM torque or velocity commands. The amplifier features 12 programmable digital inputs and four programmable digital outputs. The Stepnet amplifier is RoHS compliant. 1.1.1: Stepper and Servo Modes Stepper Mode In stepper mode, the amplifier operates as a traditional, open position loop, stepper amplifier. With the addition of optional encoder feedback in stepper mode, the amplifier can monitor and report actual motor position and optionally apply a proportional gain to correct following error. Also, a position-tracking window can be set up along with a programmable following error warning and fault. Servo Mode In servo mode with motor encoder feedback, the amplifier operates as a true, closed loop, servo amplifier controlling a stepper motor. Using motor encoder feedback, the amplifier can monitor actual motor position and velocity and correct its output so the motor follows the commanded input precisely. The amplifier can be configured to accept current, velocity, or position commands. Use of the amplifier in servo mode can result in quieter operation and reduced power consumption. 1.1.2: Amplifier Power The main power input (+HV) to the Stepnet Panel (STP) amplifier can range from 20 to 75 Vdc. This power can be supplied by an inexpensive, unregulated DC power supply. An auxiliary power input allows the digital processor to stay active when the main +HV supply has been removed. Mains input voltage to the Stepnet Panel AC (STX) can range from 100 to 120 Vac or 200 to 240 Vac single-phase at 50 to 60 Hz. This allows Stepnet the ability to work in the widest possible range of industrial settings. Model 10 Continuous Current Peak Current Voltage STP-075-07 5A 7A STP-075-10 10 A 10 A STX-115-07 5A 7A 100 - 120 Vac STX-230-07 5A 7A 100 - 240 Vac 20 - 75 Vdc Copley Controls Stepnet Panel Amplifier User Guide Introduction 1.2: Amplifier Commissioning with CME 2 Amplifier commissioning is fast and simple using Copley Controls CME 2 software. All of the operations needed to configure the amplifier are accessible through CME 2. CME 2 communicates with Stepnet via an RS-232 link or CAN. The multi-drop feature allows CME 2 to use a single RS232 serial connection to one amplifier as a gateway to other amplifiers linked together by CAN bus connections. The CME 2 Auto Phasing routine eliminates the "wire and try" method of connecting the motor and optional encoder to the amplifier. After wiring the motor and encoder to the amplifier, the Auto Phasing routine determines the correct motor polarity and encoder phasing to match the user’s "positive" direction. The amplifier configuration data can be saved to the PC as a file that contains all the amplifier settings. This file can then be copied to new amplifiers, making it possible to quickly duplicate amplifier/motor configurations. 1.3: CANopen for Distributed Control CANopen compliance allows the amplifier to take instruction from a master application over a CAN network to perform homing operations, point-to-point motion, and interpolated motion. Multiple drives can be tightly synchronized for high performance coordinated motion. Copley Motion Libraries (CML) and Copley Motion Objects (CMO) make CANopen system commissioning fast and simple. All network housekeeping is taken care of automatically by a few simple commands linked into your application program. CML provides a suite of C++ libraries, allowing a C++ application program to communicate with and control an amplifier over the CANopen network. CMO provides a similar suite of COM objects that can be used by Visual Basic, .NET, LabVIEW, or any other program supporting the COM object interface. Copley Controls Corp. 11 Introduction 12 Stepnet Panel Amplifier User Guide Copley Controls CHAPTER 2: OPERATIONAL THEORY This chapter describes the basics of Stepnet operation. Contents include: Title Page 2.1: Amplifier Power: Stepnet Panel (STP) .................................................................................................................................. 14 2.2: Amplifier Power: Stepnet Panel AC (STX) ............................................................................................................................ 15 2.3: Stepper Mode Operation....................................................................................................................................................... 16 2.4: Servo Mode Operation.......................................................................................................................................................... 18 2.5: Input Command Types ......................................................................................................................................................... 25 2.6: Communication .................................................................................................................................................................... 30 2.7: Limit Switches ...................................................................................................................................................................... 33 2.8: Brake Operation ................................................................................................................................................................... 34 2.9: Status Indicators................................................................................................................................................................... 35 2.10: Protection ........................................................................................................................................................................... 37 2.11: Position and Servo Velocity Errors...................................................................................................................................... 39 2.12: Inputs ................................................................................................................................................................................. 42 2.13: Outputs............................................................................................................................................................................... 42 Copley Controls Corp. 13 Operational Theory Stepnet Panel Amplifier User Guide 2.1: Amplifier Power: Stepnet Panel (STP) 2.1.1: Stepnet Panel (STP) High Voltage (+HV) Power A Stepnet Panel (STP) amplifier typically operates from a transformer-isolated, unregulated DC power supply. The supply should be sized such that the maximum output voltage under high-line and no-load conditions does not exceed the amplifier's maximum voltage rating. Power supply rating depends on the power delivered to the load by the amplifier. In many cases, the continuous power output rating of the amplifier is considerably higher than the actual power required the load. By appropriately selecting the boost, run and hold current levels in stepper mode or by using servo mode, it is often possible to use a smaller power supply then would normally be required. Operation from regulated switching power supplies is possible if a diode is placed between the power supply and amplifier to prevent regenerative energy from reaching the output of the supply. If this is done, there must be external capacitance between the diode and the amplifier. 2.1.2: Stepnet Panel (STP) Auxiliary Power Stepnet has an Auxiliary Power input which can keep the amplifier communications and feedback circuits active when the PWM output stage has been disabled by removing the main +HV supply. This can occur during EMO (Emergency Off) conditions where the +HV supply must be removed from the amplifier to ensure operator safety. The Auxiliary Power input operates from any DC voltage that is within the operating voltage range of the amplifier. The higher of the two voltages, +HV or Auxiliary, will power the DC/DC converter that supplies operating voltages to the amplifier DSP and control circuits. As long as the +HV voltage is greater than the auxiliary power voltage it will power the DC/DC converter and the auxiliary power input will draw no current. Connection of an Auxiliary power supply is optional. 14 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.2: Amplifier Power: Stepnet Panel AC (STX) Power distribution within the Stepnet Panel AC (STX) is divided into three sections: +24 Vdc, logic/signal, and high voltage. Each is isolated from the other. 2.2.1: Logic/Signal Power An internal DC/DC converter operates from the +24 Vdc Logic Supply input and creates the required logic/signal operating voltages, the isolated voltages required for the high-voltage control circuits, and a +5 Vdc supply for powering the motor encoder circuits. All the digital and analog inputs, digital outputs, and encoder inputs are referenced to the same signal common. The CAN interface is optically isolated. Deriving internal operating voltages from a separate source enables the amplifier to stay on-line when the mains have been disconnected for emergency-stop or operator-intervention conditions. This allows CAN bus and serial communications to remain active so that the amplifier can be monitored by the control system while the mains power is removed. 2.2.2: High Voltage Mains power drives the high-voltage section. It is rectified and capacitor-filtered to produce the DC bus: the DC “link” power that drives the PWM inverter, where it is converted into the voltages that drive the stepper motor. An internal solid-state switch and power resistor provides dissipation during regeneration when the mechanical energy of the motor is converted back into electrical energy. This prevents charging the internal capacitors to an overvoltage condition. Copley Controls Corp. 15 Operational Theory Stepnet Panel Amplifier User Guide 2.3: Stepper Mode Operation 2.3.1: Stepper Mode Control The amplifier receives target position commands from the digital inputs or over the CAN interface. When using the digital inputs, the amplifier's internal trajectory generator calculates a trapezoidal motion profile based on the trajectory limit parameters. The trajectory generator updates the calculated profile in real time as additional position commands are received. The output of the generator is an instantaneous limited position command. The vector generator accepts this command and calculates a limited current command which is the input to the current loop. For information on the current loop see Servo Current Mode and Current Loop (p. 19). Refer to Copley Controls’ CANopen Programmer’s Manual for position loop operation while under CAN control. In stepper mode, the trajectory generator accepts a target position and provides a current demand to the current limiter. The current limiter provides a limited current to the stepper current loop. The stepper current loop outputs a PWM command to drive the motor. Actual current feedback is used to close the current loop in the amplifier. Position feedback from an optional encoder can be used to provide position maintenance data to the external controller program. Target Position Control Program Position Command Trajectory Generator Limited Current Vector Generator Actual Position (w ith optional encoder) PWM Command Stepper Current Loop Motor/ Encoder Actual Current 2.3.2: Full Stepping Full stepping is a traditional and simple approach to driving a step motor. The motor moves when the amplifier stops applying current to one phase and applies it to the other. The amplifier can apply current to either of these two phases in either direction (i.e., positive current into phase A, negative into phase A, positive into B, negative into B). This allows the amplifier to make the motor come to rest in 4 distinct positions for each magnetic poll pair of the motor. Step motors typically have 50 or 100 poll pairs. This means a full stepping amplifier can make the motor come to rest at 200 or 400 distinct positions or steps. These motors are often described as being 1.8 degree / step, or 0.9 degree / step. (360 degrees/200 steps gives 1.8 degrees/step). The Stepnet amplifier can be set to full stepping mode by the programming the microsteps/rev value equal to the motors step/rev value. 16 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.3.3: Microstepping Through microstepping, Stepnet amplifiers provide a much higher degree of control over a motor’s position than does an amplifier that only supports full stepping. The Stepnet amplifier can apply varying amounts of current into both phases of the motor at the same time, making it possible to rest the motor not only at the full step locations, but at points or microsteps between them, and thus allow a high degree of control over the motor’s position. There is virtually no limit on the number of microsteps/rev that can be programmed into the Stepnet amplifier. The practical limit depends on the motor, but a value on the order of 4096 microsteps/electrical cycle is generally reasonable. Programming a very high value will limit the maximum velocity of the motor. When a high resolution encoder is connected to the motor, it is sometimes advantageous to program the number of microsteps to be equal to the number of encoder counts. Some drive manufacturers require that the number of microsteps/rev be an integer multiple of the number of electrical cycles. The Stepnet amplifiers do not have such a limitation. 2.3.4: Current Control in Stepper Mode The Stepnet amplifier uses three programmable current settings to control the current applied to the motor: boost, run, and hold. Boost current is applied to motor while it is accelerating or decelerating. Since it is only applied for a short amount of time, it can typically be set higher then the motor's continuous rated value. Another parameter, time at boost, specifies how long the boost current may be applied to the motor. If acceleration or deceleration time exceeds this limit, the current will decrease to the run value even though the motor is still accelerating/decelerating. The run current is applied to the motor while it running at a constant velocity. The hold current is used after the motor has stopped running and after the time specified by the run to hold parameter has expired. A small amount of jitter can occur when Stepper motors are at rest under hold current. To prevent this, the Stepnet features an optional voltage mode. After the time specified in the hold to voltage parameter has expired, the amplifier enters the voltage mode, locking the duty cycle to prevent jitter. 2 An I T algorithm is used to protect the motor from overheating by basically averaging the amount of current applied to the motor and not allowing it exceed the run current setting. If boost current is used, then the motor must spend time with hold current applied so the average does not exceed the run setting. See I2T Time Limit Algorithm (p. 167). NOTE: Current loop operation in stepper mode is very similar to current loop operation in servo mode. Reading the description of servo mode operation can be helpful in understanding stepper mode operation. When doing so, make the following substitutions: where stepper mode uses run current, servo mode uses continuous current; where stepper mode uses boost current, servo mode uses peak current. Also, there is no servo mode equivalent to the stepper mode hold current. For more details about current loop operation, see Servo Current Mode and Current Loop (p. 19). Copley Controls Corp. 17 Operational Theory Stepnet Panel Amplifier User Guide 2.4: Servo Mode Operation 2.4.1: Servo Modes and Control Loops Nesting of Servo Mode Control Loops and Modes In servo mode, the Stepnet uses up to three nested control loops - current, velocity, and position to control a motor in three associated operating modes. Servo Mode Nested Loops Illustration In servo position mode, the amplifier uses all three loops, as shown below. The loops are nested: the current loop within the velocity loop, within the position loop. Stated another way: the position loop drives the velocity loop, which drives the current loop. Limits Target Position Position Demand Velocity Limiter Actual Position Current Demand Velocity Loop FILTER Position Loop Limited Velocity FILTER Trajectory Generator Velocity Demand Limited Current Current Limiter Derived Velocity PWM Command Current Loop Motor/ Sensors Actual Current Servo Control Loops per Operating Mode The loops are employed in the operating modes as described below. Operating Mode Servo Position Loop Input Output Servo Velocity Loop Input Output Current Velocity and position loops not employed in current mode. Velocity Position loop not employed in velocity mode. External command. Position External command. Velocity command from position loop. Velocity command (input to the velocity loop). Current command (input to current loop). Servo Current Loop Input Output External command. Current command from velocity loop. Voltage command (input to the PWM power stage) Basic Attributes of All Servo Control Loops These loops (and servo control loops in general) share several common attributes: Loop Attribute Description Command input Every loop is given a value to which it will attempt to control. For example, the velocity loop receives a velocity command that is the desired motor speed. Limits Limits are set on each loop to protect the motor and/or mechanical system. Feedback The nature of servo control loops is that they receive feedback from the device they are controlling. For example, the position loop uses the actual motor position as feedback. Gains These are constant values that are used in the mathematical equation of the servo loop. The values of these gains can be adjusted during amplifier setup to improve the loop performance. Adjusting these values is often referred to as tuning the loop. Output The loop generates a control signal. This signal can be used as the command signal to another control loop or the input to a power amplifier. 18 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.4.2: Servo Current Mode and Current Loop Servo Current Loop Diagram As shown below, the “front end” of the servo current loop is a limiting stage. The limiting stage accepts a current command, applies limits, and passes a limited current command to the summing junction. The summing junction takes the commanded current, subtracts the actual current (represented by the feedback signal), and produces an error signal. This error signal is then processed using the integral and proportional gains to produce a command. This command is then applied to the amplifier’s power stage. Current Loop Current Integral Gain (Ci) Current Demand Current Limiter Limited Current + Current Offset Current Proportional Gain (Cp) + PWM Command + Motor - Limits: Peak Current Continuous Current Peak Current Limit Time Feedback (Actual Current) Inputs In servo current mode, the current command comes from external sources such as the amplifier’s PWM inputs, or internal sources, such as a Copley Virtual Machine (CVM) program. See PWM Input (Servo Mode Only) (p. 29). In servo velocity or position modes, the current command is generated by the velocity loop. Offset The servo current loop offset is intended for use in applications where there is a constant force applied to, or required of, the motor and the system must control this force. Typical applications would be a vertical axis holding against gravity, or web tensioning. This offset value is summed with the current command before the limiting stage. Limits The current command is limited based on the following parameters: Limiter Description Peak Current Limit Maximum current that can be generated by the amplifier for a short duration of time. This value cannot exceed the peak current rating of the amplifier. Continuous Current Limit Maximum current that can be constantly generated by the amplifier. 2 I T Time Limit Maximum amount of time that the peak current can be applied to the motor. The amplifier can be programmed to fold back the current to the continuous current setting or generate a latched fault when this time is exceeded. 2 For more details, see I T Time Limit Algorithm (p. 167). Note: Although the current limits set by the user may exceed the amplifier's internal limits, the amplifier operates using both sets of limits in parallel, and therefore will not exceed its own internal limits regardless of the values programmed. Copley Controls Corp. 19 Operational Theory Stepnet Panel Amplifier User Guide Current Loop Gains The current loop uses these gains: Gain Description Cp - Current loop proportional The current error (the difference between the actual and the limited commanded current) is multiplied by this value. The primary effect of this gain is to increase bandwidth (or decrease the step-response time) as the gain is increased. Ci - Current loop integral The integral of the current error is multiplied by this value. Integral gain reduces the current error to zero over time. It controls the DC accuracy of the loop, or the flatness of the top of a square wave signal. The error integral is the accumulated sum of the current error value over time. Current Loop Output The output of the current loop is a command that sets the duty cycle of the PWM output stage of the amplifier. Auto Tune CME 2 provides a current loop Auto Tune feature, which automatically determines optimal Cp and Ci values for the motor. For more information, see the CME 2 User Guide. 20 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.4.3: Servo Velocity Mode and Velocity Loop Servo Velocity Loop Diagram As shown below, the “front end” of the servo velocity loop is a limiting stage. This accepts a velocity command, applies limits, and passes a limited velocity command to the summing junction. The summing junction takes the limited velocity command, subtracts the actual velocity, represented by the feedback signal, and produces an error signal. This error signal is then processed using the integral and proportional gains to produce a current command. Optional filters can be used to reduce the excitation of any resonance in the system. They are available on both the input command and the output current demand, but most typically used on the output only. Velocity Loop Velocity Demand Velocity Limiter Filter Limited Velocity Velocity Integral Gain (Vi) + Velocity Proportional Gain (Vp) + Filter + Current Demand Limits: Velocity Feedback (Derived Velocity) Acceleration* Deceleration* Emergency Stop Deceleration* *Not used w hen velocity loop is controlled by position loop. See "Velocity Loop Limits" for details. Inputs In servo velocity mode, the velocity command comes from external sources such as the amplifier’s PWM inputs, or internal sources, such as a Copley Virtual Machine (CVM) program. See PWM Input (Servo Mode Only) (p. 29). In servo position mode, the velocity command is generated by the position loop. Servo Velocity Loop Limits The velocity command is limited based on the following set of parameters designed to protect the motor and/or the mechanical system. Limiter Description Velocity Limit Sets the maximum velocity command input to the servo velocity loop. Acceleration Limit Limits the maximum acceleration rate of the commanded velocity input to the servo velocity loop. This limit is used in servo velocity mode only. In servo position mode, the trajectory generator handles acceleration limiting. Deceleration Limit Limits the maximum deceleration rate of the commanded velocity input to the servo velocity loop. This limit is used in servo velocity mode only. In servo position mode, the trajectory generator handles deceleration limiting. Fast Stop Ramp Specifies the deceleration rate used by the servo velocity loop when the amplifier is hardware disabled. (Fast stop ramp is not used when amplifier is software disabled.) If the brake output is active, the fast stop ramp is used to decelerate the motor before applying the brake. Note that Fast Stop Ramp is used only in servo velocity mode. In servo position mode, the trajectory generator handles controlled stopping of the motor. There is one exception: if a non-latched following error occurs in position mode, then the amplifier goes into velocity mode and the Fast Stop Ramp is used. For more information, see Following Error Fault Details (p. 40). Copley Controls Corp. 21 Operational Theory Stepnet Panel Amplifier User Guide Diagram: Effects of Limits on Velocity Command The following diagram illustrates the effects of the servo velocity loop limits. Limited Velocity Commanded Velocity Vel Limit Accel Limit Decel Limit Servo Velocity Loop Gains The servo velocity loop uses these gains: Gain Description Vp - Velocity loop proportional The velocity error (the difference between the actual and the limited commanded velocity) is multiplied by this gain. The primary effect of this gain is to increase bandwidth (or decrease the step-response time) as the gain is increased. Vi - Velocity loop integral The integral of the velocity error is multiplied by this value. Integral gain reduces the velocity error to zero over time. It controls the DC accuracy of the loop, or the flatness of the top of a square wave signal. The error integral is the accumulated sum of the velocity error value over time. Servo Velocity Gains Shift The Velocity Gains Shift feature adjusts the resolution of the units used to express Vp and Vi, providing more precise tuning. If the non-scaled value of Vp or Vi is 64 or less, the Low Gains Shift option is available to increase the gains adjustment resolution. (Such low values are likely to be called for when tuning a linear motor with an encoder resolution finer than a micrometer.) If the non-scaled value of Vp or Vi is 24001 or higher, the High Gains Shift option is available to decrease the gains adjustment resolution. Servo Velocity Loop Command and Output Filters The servo velocity loop contains two programmable digital filters. The input filter should be used to reduce the effects of a noisy velocity command signal. The output filter can be used to reduce the excitation of any resonance in the motion system. Two filter classes can be programmed: the Low-Pass and the Custom Bi-Quadratic. The LowPass filter class includes the Single-Pole and the Two-Pole Butterworth filter types. The Custom Bi-Quadratic filter allows advanced users to define their own filters incorporating two poles and two zeros. For more information, see the CME 2 User Guide. Servo Velocity Loop Outputs The output of the servo velocity loop is a current command used as the input to the servo current loop. 22 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.4.4: Servo Position Mode and Position Loop Servo Position Loop Diagram The amplifier receives position commands from internal sources, such as a Copley Virtual Machine (CVM) program, or external input sources such as the amplifier’s digital inputs or a CANopen or DeviceNet network. When using the digital inputs, the amplifier's internal trajectory generator calculates a trapezoidal motion profile based on the trajectory limit parameters. The trajectory generator updates the calculated profile in real time as additional position commands are received. The output of the generator is an instantaneous position command (limited position). In addition, values for the instantaneous profile velocity and acceleration are generated. These signals, along with the actual position feedback, are processed by the position loop to generate a velocity command. The following diagram summarizes the servo position loop. Position Loop Profile Velocity Target Position Trajectory Ge ne rator Velocity Feed Forw ard (Vff) Profile Acceleration Limited Position Acceleration Feed Forw ard (Aff) + Position Proportional Gain (Pp) + + Gain Multiplier + Velocity Demand - Limits: Max velocity Max accel Max decel Abort decel Feedback (Actual Position) The Clear Limits feature is described in Position Loop Settings, p. 141. Servo Position Mode Inputs In servo position mode, various input sources can drive the amplifier: • • The amplifier receives position commands directly from the digital inputs. For more information, see Digital Inputs (p. 100). The amplifier receives position commands over a CANopen or DeviceNet network via the amplifier’s CAN interface. For more information, see Communication (p. 30) and the Copley DeviceNet Programmer’s Guide. Trajectory Limits In servo position mode, the trajectory generator applies the following user-set limits to generate the motion profile. Limiter Description Maximum Velocity* Limits the maximum speed of the profile. Maximum Acceleration* Limits the maximum acceleration rate of the profile. Maximum Deceleration* Limits the maximum deceleration rate of the profile. Abort Deceleration Specifies the deceleration rate used by the trajectory generator when motion is aborted. *When the amplifier is driven by pulse and direction commands, Maximum Velocity, Acceleration, and Deceleration function as maximum values. When the amplifier is driven by any other command input, Maximum Velocity, Acceleration, and Deceleration function as commanded values. Copley Controls Corp. 23 Operational Theory Stepnet Panel Amplifier User Guide Servo Position Loop Inputs From the Trajectory Generator The servo position loop receives the following inputs from the trajectory generator. Input Description Profile Velocity The instantaneous velocity value of the profile. Used to calculate the velocity feed forward value. Profile Acceleration The instantaneous acceleration/deceleration value of the profile. Used to calculate the acceleration feed forward value. Limited Position The instantaneous commanded position of the profile. Used with the actual position feedback to generate a position error. Servo Position Loop Gains The following gains are used by the servo position loop to calculate the velocity command: Gain Description Pp - Position loop proportional The loop calculates the position error as the difference between the actual and limited position values. This error in turn is multiplied by the proportional gain value. The primary effect of this gain is to reduce the following error. Vff - Velocity feed forward The value of the profile velocity is multiplied by this value. The primary effect of this gain is to decrease following error during constant velocity. Aff - Acceleration feed forward The value of the profile acceleration is multiplied by this value. The primary effect of this gain is to decrease following error during acceleration and deceleration. Gain Multiplier The output of the position loop is multiplied by this value before being passed to the velocity loop. Servo Position Loop Feedback The feedback to the loop is the actual motor position, obtained from a quadrature encoder attached to the motor. Servo Position Loop Output The output of the servo position loop is a velocity command used as the input to the velocity loop. 24 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.5: Input Command Types The amplifier can be controlled by a variety of external sources: analog voltage input (STX only), digital inputs, CAN network (CANopen or DeviceNet), or over an RS-232 serial connection using ASCII commands. The amplifier can also function as a stand-alone motion controller running an internal CVM program or using its internal function generator. 2.5.1: Analog Command Input (STX Servo Mode Only) Overview The amplifier can be driven by an analog voltage signal through the analog command input. The amplifier converts the signal to a current, velocity, or position command as appropriate for current, velocity, or position mode operation, respectively. The analog input signal is conditioned by the scaling, dead band, and offset settings. A programmable filter is also available on the analog input. See the “Low-Pass and Bi-Quad Filters” appendix in the CME 2 User’s Guide. Scaling The magnitude of the command generated by an input signal is proportional to the input signal voltage. Scaling controls the input-to-command ratio, allowing the use of an optimal command range for any given input voltage signal range. For example, in current mode, with default scaling, +10 Vdc of input generates a command equal to the amplifier’s peak current output; +5 Vdc equals half of that. Scaling could also be useful if, for example, the signal source generates a signal range between 0 and +10 Vdc, but the command range only requires +7.5 Vdc of input. In this case, scaling allows the amplifier to equate +7.5 Vdc with the amplifier’s peak current (in current mode) or maximum velocity (in velocity mode), increasing the resolution of control. Dead Band To protect against unintended response to low-level line noise or interference, the amplifier can be programmed with a “dead band” to condition the response to the input signal voltage. The amplifier treats anything within the dead band ranges as zero, and subtracts the dead band value from all other values. For instance, with a dead band of 100 mV, the amplifier ignores signals between –100 mV and +100 mV, and treats 101 mV as 1 mV, 200 mV as 100 mV, and so on. Copley Controls Corp. 25 Operational Theory Stepnet Panel Amplifier User Guide 200 Output 100 Dead Band 0 -100 -200 -200 -100 0 Input 100 200 Offset To remove the effects of voltage offsets between the controller and the amplifier in open loop systems, CME 2 provides an Offset parameter and a Measure function. The Measure function takes 10 readings of the analog input voltage over a period of approximately 200 ms, averages the readings, and then displays the results. The Offset parameter allows the user to enter a corrective offset to be applied to the input voltage. The offset can also set up the amplifier for bi-directional operation from a uni-polar input voltage. An example of this would be a 0 to +10 Vdc velocity command that had to control 1000 rpm CCW to 1000 rpm CW. Scale would be set to 2000 rpm for a +10 Vdc input and Offset set to -5V. After this, a 0 Vdc input command would be interpreted as -5 Vdc, which would produce 1000 rpm CCW rotation. A +10 Vdc command would be interpreted as +5 Vdc and produce 1000 rpm CW rotation. Monitoring the Analog Command Voltage The analog input voltage can be monitored in the CME 2 control panel and oscilloscope. The voltage displayed in both cases is after both offset and deadband have been applied. Analog Command in Position Mode The amplifier’s Analog Position command operates as a relative motion command. When the amplifier is enabled the voltage on the analog input is read. Then any change in the command voltage will move the axis a relative distance, equal to the change in voltage, from its position when enabled. To use the analog position command as an absolute position command, the amplifier should be homed every time it is enabled. The Homing sequence may be initiated by CAN, ASCII serial, or CVM Indexer program commands. 26 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.5.2: Digital Position Inputs Three Formats In position mode, the amplifier can accept position commands via two digital inputs, using one of these signal formats: pulse and direction, count up/count down, or quadrature. In all three formats, the amplifier can be configured to invert the command. Pulse Smoothing In position mode, the amplifier’s trajectory generator ensures smooth motion even when the command source cannot control acceleration and deceleration rates. Pulse and Direction Format In pulse and direction format, one input takes a series of pulses as motion step commands, and another input takes a high or low signal as a direction command, as shown below. Pulse Input Direction Input Velocity Command The amplifier can be set to increment position on the rising or falling edge of the signal. Stepping resolution can be programmed for electronic gearing. Count Up/Count Down Format In the count up/count down format, one input takes each pulse as a positive step command, and another takes each pulse as a negative step command, as shown below. Up Input Down Input Velocity Command The amplifier can be set to increment position on the rising or falling edge of the signal. Stepping resolution can be programmed for electronic gearing. Copley Controls Corp. 27 Operational Theory Stepnet Panel Amplifier User Guide Quadrature Format In quadrature format, A/B quadrature commands from a master encoder (via two inputs) provide velocity and direction commands, as shown below. A Input B Input Velocity Command The ratio can be programmed for electronic gearing. 28 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.5.3: PWM Input (Servo Mode Only) Two Formats The amplifier can accept a pulse width modulated signal (PWM) signal to provide a current command in servo current mode or a velocity command in servo velocity mode. The PWM input can be programmed for two formats: 50% duty cycle (one-wire) or 100% duty cycle (two-wire). 50% Duty Cycle Format (One-Wire) The input takes a PWM waveform of fixed frequency and variable duty cycle. As shown below, a 50% duty cycle produces zero output from the amplifier. Increasing the duty cycle toward 100% commands a positive output; decreasing the duty cycle commands a negative output. Decreasing Duty Cycle Increasing Duty Cycle PWM Input 50 % Duty Cycle Max + Amplifie r Output 0 Max - The command can be inverted so that increased duty cycle commands negative. 100% Duty Cycle Format (Two-Wire) One input takes a PWM waveform of fixed frequency and variable duty cycle, and the other input takes a DC level that controls the polarity of the output. A 0% duty cycle creates a zero command, and a 100% duty cycle creates a maximum command level. The command can be inverted so that increasing the duty cycle decreases the output and vice versa. 100% Duty Cycle 0% Duty Cycle 100% Duty Cycle PWM Input Direction Input Max + Amplifier Output 0 Min - Failsafe Protection from 0 or 100% Duty Cycle Commands In both formats, the amplifier can be programmed to interpret both 0 and 100% duty cycle as a zero command. This provides a measure of safety in case of a controller failure or a cable break. Copley Controls Corp. 29 Operational Theory Stepnet Panel Amplifier User Guide 2.6: Communication As described below, the amplifier features multiple communication interfaces, each used for different purposes. Interface Description RS-232 port The amplifier features a three-wire RS-232 port. Control commands can be sent over the RS-232 port using Copley Controls ASCII interface commands. In addition, CME 2 software communicates with the amplifier (using a binary protocol) over this link for amplifier commissioning, adjustments, and diagnostics. For RS-232 port specifications, see Serial Interface (p. 51). For RS-232 port wiring instructions, see Stepnet Panel (STP) RS-232 Serial Communications (J4) (p. 66) or Stepnet Panel AC (STX) RS-232 Serial Communications (J8) (p. 83). Note that CME 2 can be used to make adjustments even when the amplifier is being controlled over the CAN interface or by the digital inputs. CAN interface When operating as a CAN node, the amplifier takes command inputs over a CANopen or DeviceNet network. CAN communications are described in the next section. Using CME 2 can affect or suspend CAN operations. ! DANGER When operating the amplifier as a CANopen or DeviceNet node, use of CME 2 to change amplifier parameters can affect CANopen or DeviceNet operations in progress. Using CME 2 to initiate motion can cause CANopen or DeviceNet operations to suspend. The operations may restart unexpectedly when the CME 2 move is stopped. Failure to heed this warning can cause equipment damage, injury, or death. 2.6.1: CAN Network and CANopen Profiles for Motion In servo or stepper position mode, the amplifier can take instruction over a two-wire Controller Area Network (CAN). CAN specifies the data link and physical connection layers of a fast, reliable network. CANopen is a set of profiles (specifications) built on a subset of the CAN application layer protocol. These profiles specify how various types of devices, including motion control devices, can use the CAN network in a highly efficient manner. Stepnet supports the relevant CANopen profiles, allowing it to operate in the following modes of operation: profile torque, profile velocity, profile position, interpolated position, and homing. 2.6.2: Supported CANopen Modes In profile torque mode, the amplifier is programmed with a torque command. When the amplifier is enabled, or the torque command is changed, the motor torque ramps to the new value at a programmable rate. When the amplifier is halted, the torque ramps down at the same rate. In profile velocity mode, the amplifier is programmed with a velocity, a direction, and acceleration and deceleration rates. When the amplifier is enabled, the motor accelerates to the set velocity and continues at that speed. When the amplifier is halted, the velocity decelerates to zero. In profile position mode, the amplifier is programmed with a velocity, a relative distance or absolute position, and acceleration and deceleration rates. On command, a complete motion profile is executed, traveling the programmed distance or ending at the programmed position. The amplifier supports both trapezoidal and s-curve profiles. 30 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory In interpolated position mode, the controller sends a sequence of points to the amplifier, each of which is a segment of a larger, more complex move, rather than a single index or profile. The amplifier then uses cubic polynomial interpolation to “connect the dots” so that the motor reaches each point at the specified velocity at the programmed time. Homing mode is used to move the axis from an unknown position to a known reference or zero point with respect to the mechanical system. The homing mode is configurable to work with a variety of combinations of encoder index, home switch, limit switches and mechanical stops. 2.6.3: Architecture CAN port CANopen As shown below, in a CANopen motion control system, control loops are closed on the individual amplifiers, not across the network. A master application coordinates multiple devices, using the network to transmit commands and receive status information. Each device can transmit to the master or any other device on the network. CANopen provides the protocol for mapping device and master internal commands to messages that can be shared across the network. Control Copley Controls Corp. Local Control Motor I/O Status CAN port CANopen Local Control I/O Sensor Other CANopen Device CAN port StepNet Amplifier CANopen Feedback CAN Network Master Controller CANopen CAN port Softw are Application StepNet Amplifier Motor 31 Operational Theory Stepnet Panel Amplifier User Guide 2.6.4: CAN Addressing A CANopen network can support up to 127 nodes. Each node must have a unique and valid seven-bit address (Node ID) in the range of 1-127. (Address 0 is reserved and should not be used.) There are several methods for setting the CAN address, using various combinations of the rotary CAN ADDR selector switch, programmed values entered into flash memory, and digital input signals. Addressing Method Description Address selector switch If the address number <= 16, CAN address can be set using the CAN ADDR switch only. Use programmed value Program address into flash only. Ignore switch. Use address switch with programmed offset value Use address switch and an offset value programmed into flash memory. Address is the sum of the offset value and the switch setting. Use inputs with programmed offset value Use inputs (user selects how many lines, 1-7) and an offset value programmed into flash. This offset value is added to the value set by the inputs to determine the address. Programmed value could be zero so that inputs alone determine address. Ignore the CAN ADDR switch. Use switch, input lines, and programmed offset value Use switch, inputs (user selects how many lines, 0-3), and an offset value programmed in to flash memory. Switch provides the lower four bits; inputs provide the next 0 - 3 bits. The offset is added to the value set by the switch and inputs to determine address. If programmed value is zero, switch and inputs alone determine address. For more information on CAN addressing, see CAN Interface (p. 112). For more information on CAN communications see Communication (p. 30). For more information on CANopen operations, see the following Copley Controls documents: • • • 32 CANopen Programmer’s Manual CML Reference Manual Copley Motion Objects Programmer’s Guide Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.7: Limit Switches 2.7.1: Use Digital Inputs to Connect Limit Switches Limit switches help protect the motion system from unintended travel to the mechanical limits. Any of the digital inputs 2-12 can be can be programmed as positive or negative limit switch inputs. An input can also be programmed as a home limit switch for homing operations. The amplifier also supports software limits, as configured in Homing Functions Settings (p. 164). 2.7.2: How the Amplifier Responds to Limit Switch Activation In all modes, in response to an active limit switch: • • • • The amplifier status indicator flashes green at fast rate. A warning is displayed on CME 2 Control Panel and the CME 2 Control Panel limit indicator turns red. (Optional) Appropriately configured digital outputs go active. See Custom Digital Output Settings: Custom Event (p. 104). The amplifier stops driving motion in the direction of an active limit switch, with the modedependent and configurable variations described below. Mode Response to Active Limit Switch Servo Current Amplifier stops driving motion in the direction of the active limit switch. The amplifier will drive motion in the opposite direction if commanded. Servo Velocity Stepper or Servo Position Responses depend on the setting of Hold position when limit switch is active (p. 101). Hold Position… not set: The amplifier aborts the trajectory in progress and stops the axis, using reverse current only, at the Abort Deceleration rate. After the axis has stopped the amplifier will not drive current in the direction of the activated limit switch. In any command mode other then a digital input mode, the amplifier will respond to commands in the opposite direction. If in digital input mode, the amplifier must be disabled and re-enabled to command motion in the opposite direction. Hold Position… set: The amplifier aborts the trajectory in progress and stops the axis at the Abort Deceleration rate. After the axis stops the amplifier servos to hold that position. The amplifier will respond to commands in the opposite direction. ! WARNING: Limit switches may be disabled. If the amplifier is switched back to current or velocity mode with Hold position when limit switch is active (p. 101) set, the limit switches will no longer function. Failure to heed this warning can cause equipment damage. WARNING Copley Controls Corp. 33 Operational Theory Stepnet Panel Amplifier User Guide 2.8: Brake Operation 2.8.1: Digital Output Controls Brake Many control systems employ a brake to hold the axis when the amplifier is disabled. Any of the digital outputs can be programmed for brake control. 2.8.2: Event- and Mode-Specific Brake/Stop Sequences Braking sequences vary depending on the amplifier’s operating mode. In current mode, disabling the amplifier activates the brake output and disables the amplifier output stages immediately. In position or velocity mode, a hardware or software disable starts a sequence of events: • • • The motor begins to decelerate (at Abort Deceleration rate in position mode or Fast Stop Ramp rate in velocity mode). At the same time, the Brake/Stop Delay Time count begins. When the motor slows to Brake/Stop Activation Velocity OR the Brake/Stop Delay Time expires, the brake output activates and PWM Delay Brake/Stop Response Time count begins. When response time has passed, the amplifier’s output stages are disabled. 2.8.3: Brake Settings As shown below, the brake settings available in position and velocity mode provide control over the braking sequence. The pre-braking delay (controlled by the deceleration rate and delay timer) allows the amplifier to slow the motor before applying the brake. PWM Delay Brake/Stop Response Time makes it possible to ensure the brake has time to lock in before disabling the power section. 34 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.9: Status Indicators 2.9.1: Amplifier and CAN Interface Status Indicators Stepnet Panel (STP): The amplifier’s status indicator is a bicolor LED labeled STATUS on the J5 connector. The CAN interface status indicator is a bicolor LED on the J6 connector. Stepnet Panel AC (STX): The amplifier’s status indicator is a bicolor LED labeled STATUS on the front panel. The CAN interface status indicator is a bicolor LED on the J4 connector. 2.9.2: Amplifier Status Indicator Operation Amplifier status indicator color/blink codes are described below. Color/Blink Code Meaning Not illuminated No power to amplifier. Steady green Amplifier is enabled and operational. Slow-blinking green Amplifier is disabled. No faults or warnings are active. Fast-blinking green A limit switch is active. The amplifier is enabled. Steady red A non-latched fault has occurred. Blinking red A latched fault has occurred. Copley Controls Corp. 35 Operational Theory Stepnet Panel Amplifier User Guide 2.9.3: CAN Interface Status Indicator Operation The amplifier status indicator color/blink codes comply with CAN Indicator Specification 303-3 as described below. Note that green and red codes are often interlaced, each indicating a different set of conditions. The green codes indicate the CANopen state machine mode of operation (preoperational, operational, or stopped). The red codes indicate the status of the physical bus (warning or error conditions). CANopen State Machine Mode of Operation Diagram Indicator State Blinking green Pre-operational. 200 ms green off 200 ms Steady green Operational green off Single flash green Stopped 1 second green off 200 ms Physical Bus Status Single flash red Warning Limit Reached 1 second red off 200 ms Double flash red Error Control Event 1 second red off 200 ms Triple flash red 200 ms Sync Error 1 second red off 200 ms Steady red Bus Off 200 ms 200 ms red off In addition, the CAN status indicator is turned off when the CAN node ID selector (CAN ADDR) is set to 0. A setting of 0, which is an invalid CAN address, shuts down most operations on the CAN interface, and the light is shut off to indicate this status. 36 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.10: Protection 2.10.1: Faults Overview Stepnet detects and responds to a set of conditions regarded as faults, such as amplifier over temperature and excessive following error. When any fault occurs, with the exception of a following error, the amplifier’s PWM output stage is disabled, the fault type is recorded in the amplifier’s internal error log (which can be viewed with CME 2), and the status LED changes to indicate a fault condition exists. A digital output can also be programmed to activate on a fault condition. The following error fault behaves with slight differences, as described in Following Error Fault Details (p. 40). The amplifier’s PWM output stage can be re-enabled after the fault condition is corrected and the amplifier faults are cleared. The process for clearing faults varies depending on whether the fault is configured as non-latched or latched. The fault-clearing descriptions below apply to all faults except for the following error fault, which is described in Following Error Fault Details (p. 40). Clearing Non-Latched Faults The amplifier clears a non-latched fault, without operator intervention, as soon as the fault condition is corrected. ! DANGER Risk of unexpected motion with non-latched faults. After the cause of a non-latched fault is corrected, the amplifier re-enables the PWM output stage without operator intervention. In this case, motion may re-start unexpectedly. Configure faults as latched unless a specific situation calls for nonlatched behavior. When using non-latched faults, be sure to safeguard against unexpected motion. Failure to heed this warning can cause equipment damage, injury, or death. Clearing Latched Faults A latched fault is cleared only after the fault has been corrected and at least one of the following actions has been taken: • • power-cycle the amplifier cycle (disable and then enable) an enable input that is configured as Enables with Clear Faults or Enables with Reset • • ) and press Clear Faults or Reset access the CME 2 Control Panel ( clear the fault over the CANopen network Example: Non-Latched vs. Latched Faults For example, the amplifier temperature reaches the fault temperature level and the amplifier reports the fault and disables the PWM output. Then, the amplifier temperature is brought back into operating range. If the Amplifier Over Temperature fault is not latched, the fault is automatically cleared and the amplifier’s PWM outputs are enabled. If the fault is latched, the fault remains active and the amplifier’s PWM outputs remain disabled until the faults are specifically cleared (as described above). Copley Controls Corp. 37 Operational Theory Stepnet Panel Amplifier User Guide Fault Descriptions The set of possible faults is described below. For details on limits and ranges, see Fault Levels (p. 52). Fault Description Fault Occurs When… Fault is Corrected When… *Amplifier Over Temperature Amplifier's internal temperature exceeds specified temperature. Temperature falls below specified temperature. Motor Phasing Error (in servo mode only) Motor fails to properly phase initialize. Amplifier is reset and re-enabled. *Feedback error (STX only) Under voltage condition detected on output of the internal +5 Vdc supply used to power the encoder. Encoder power returns to specified voltage range. Differential encoder signal fault. Line errors are corrected. *Motor Over Temperature Motor over-temperature input changes state to indicate an over-temperature condition. Input changes back to normal operating state. Under Voltage +HV voltage falls below specified voltage limit. +HV voltage returns to specified voltage range. Over Voltage +HV voltage exceeds specified voltage limit. +HV voltage returns to specified voltage range. *Following Error (with encoder only) User set following error threshold exceeded. See Position and Servo Velocity Errors (p. 39). *Short Circuit Detected Output to output, output to ground, internal PWM bridge fault. Short circuit has been removed. Over Current (Latched) Output current I T limit has been exceeded. Amplifier is reset and re-enabled. Command Input Fault PWM command at 0 or 100% duty cycle with the Allow 100% Output option disabled. Proper PWM input command is restored. 2 PWM frequency out of range. *Latched by default. STX Encoder Loss Detection The Stepnet Panel AC (STX) amplifier incorporates Encoder Loss Detection circuitry that continuously monitors the integrity of the differential encoder feedback signals. When a fault in any of the differential pairs is detected, a feedback error occurs. To enable or disable this protection, see Enter Motor/Feedback/Brake Settings Manually (p. 96). In applications where Encoder Loss Detection is enabled and the encoder does not have an index channel or the index channel is not wired to the amplifier, the amplifier’s index channel connector pins must be jumpered as shown in Stepnet Panel AC (STX) J6 Quad A/B Incremental Encoder Wiring Diagram – No Index (p. 76). 38 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.11: Position and Servo Velocity Errors 2.11.1: Error-Handling Methods In stepper mode with encoder or servo position mode, any difference between the limited position output of the trajectory generator and the actual motor position is a position error. The servo or stepper position loop uses complementary methods for handling position errors: following error fault, following error warning, and a position-tracking window. Likewise, in servo velocity or servo position mode, any difference between the limited velocity command and actual velocity is a velocity error. The servo velocity loop uses a velocity tracking window method to handle velocity errors. (There is no velocity error fault.) 2.11.2: Following Error Faults When the position error reaches the programmed fault threshold, the amplifier immediately faults. (The following error fault can be disabled.) For detailed information, see Following Error Fault Details (p. 40). 2.11.3: Following Error Warnings When the position error reaches the programmed warning threshold, the amplifier immediately sets the following error warning bit in the status word. This bit can be read over the CAN network. It can also be used to activate a digital output. 2.11.4: Position and Velocity Tracking Windows When the position error exceeds the programmed tracking window value, a status word bit is set. The bit is not reset until the position error remains within the tracking window for the programmed tracking time. This bit can be read over the CAN network. It can also be used to activate a digital output. In servo mode, a similar method is used to handle velocity errors. For detailed information, see Tracking Window Details (p. 41). Copley Controls Corp. 39 Operational Theory Stepnet Panel Amplifier User Guide 2.11.5: Following Error Fault Details Position Error Reaches Fault Level As described earlier, position error is the difference between the limited position output of the trajectory generator and the actual position. When position error reaches the programmed Following Error Fault level, the amplifier faults (unless the following error fault is disabled.) As with a warning, a status bit is set. In addition, the fault is recorded in the error log. Additional responses and considerations depend on whether the fault is non-latched or latched, as described below. Amplifier Response to Non-Latched Following Error Fault In servo mode, when a non-latched following error fault occurs, the amplifier drops into velocity mode and applies the Fast Stop Ramp deceleration rate to bring the motor to a halt. The amplifier PWM output stage remains enabled, and the amplifier holds the velocity at zero, using the velocity loop. In stepper mode, when a non-latched following error fault occurs, the current move is aborted and the amplifier decelerates at the Trajectory Abort Deceleration rate. The amplifier PWM output stage remains enabled and the Hold current is applied to the motor. Resuming Operations After a Non-Latched Following Error Fault The clearing of a non-latched following error depends on the amplifier’s mode of operation. If the amplifier is operating as a CAN node, starting a new trajectory, using CANopen commands, will clear the fault and return the amplifier to normal operating condition. If the amplifier is receiving position commands from the digital inputs, then the amplifier must be disabled and then reenabled using a hardware input or though CME 2 software commands. After re-enabling, the amplifier will operate normally. Amplifier Response to a Latched Following Error Fault When a latched following error fault occurs, the amplifier disables the output PWM stage without first attempting to apply a deceleration rate. Resuming Operations After a Latched Following Error Fault A latched following error fault can be cleared using the steps used to clear other latched faults: • • power-cycle the amplifier cycle (disable and then enable) an enable input that is configured as Enables with Clear Faults or Enables with Reset • • access the CME 2 Control Panel ( ) and press Clear Faults or Reset clear the fault over the CANopen network 40 Copley Controls Stepnet Panel Amplifier User Guide Operational Theory 2.11.6: Tracking Window Details Proper Tracking Over Time As described earlier, position error is the difference between the limited position output of the trajectory generator and the actual position. In servo mode, velocity error is the difference between commanded and actual velocity. When the position or velocity error exceeds the programmed tracking window value, a status word bit is set. The bit is not reset until the error remains within the tracking window for the programmed tracking time. Servo Mode Velocity Tracking Illustration The following diagram illustrates the use of tracking window and time settings in servo velocity mode. Actual Velocity Limited Velocity ± Tracking Window Tracking Time Tracking Window Output Copley Controls Corp. 41 Operational Theory Stepnet Panel Amplifier User Guide 2.12: Inputs 2.12.1: Digital Inputs The amplifier has 12 digital inputs (IN1-IN12). IN1 is always used as an enable input. IN2-IN12 are fully programmable. See Digital Input Functions (p.102). 2.12.2: Input Filters Two types of input RC filters are used: GP (general-purpose) and HS (high-speed). The digital command inputs, such as Count Up/Count Down and PWM, are wired to inputs having the HS filters. Inputs with the GP filters are used for general-purpose logic functions, limit switches, and the motor temperature sensor. 2.12.3: Debounce Time To prevent undesired multiple triggering caused by switch bounce upon switch closures, each input can be programmed with a debounce time. The programmed time specifies how long an input must remain stable at a new state before the amplifier recognizes the state. The programmed debounce time is ignored if the input is programmed as a digital position command, PWM input or encoder input. 2.12.4: Configure for Pull Up/Pull Down Resistors by Groups Pre-defined groups of inputs can be programmed to have either an internal pull up or pull down resistor. See Stepnet Panel (STP) J3 Pin Description (p. 62) or Stepnet Panel AC (STX) J7 Pin Description (p. 79) for groupings. 2.13: Outputs 2.13.1: Digital Outputs The amplifier has four programmable digital outputs. These outputs are open-drain MOSFETs, each with a pull-up resistor, in series with a diode, connected to the amplifier’s internal +5 Vdc supply. This design allows the outputs to be directly connected to optically isolated PLC inputs that reference a voltage higher than +5 Vdc, typically +24 Vdc. The diode prevents current flow between the +24 Vdc supply and the internal +5 Vdc supply though the pull-up resistor. This current, if allowed to flow, could turn on the PLC input, giving a false indication of the amplifier’s true output state. The outputs require an external fly-back diode to be installed across any inductive loads, such as relays, that are connected to them. NOTE: Outputs will remain off (high) after powering up the amplifier, for a maximum delay of 2 seconds. They will then assume their programmed states. The outputs will also turn off during an amplifier reset and return to their programmed state after a maximum delay of 0.5 seconds. 42 Copley Controls CHAPTER 3: SPECIFICATIONS This chapter describes the amplifier specifications for the Stepnet Panel (STP) and Stepnet Panel AC (STX) amplifiers. Contents include: Title Page 3.1: Agency Approvals................................................................................................................................................................. 44 3.2: Power Input .......................................................................................................................................................................... 44 3.2.1: Stepnet Panel (STP) Power Input ............................................................................................................................ 44 3.2.2: Stepnet Panel AC (STX) Power Input ...................................................................................................................... 44 3.3: Power Output........................................................................................................................................................................ 45 3.3.1: Stepnet Panel (STP) Power Output ......................................................................................................................... 45 3.3.2: Stepnet Panel AC (STX) Power Output.................................................................................................................... 45 3.3.3: Power Output Configuration (STP and STX) ............................................................................................................ 45 3.4: Control Loops ....................................................................................................................................................................... 46 3.5: Stepnet Panel AC (STX) Internal Regen Circuit.................................................................................................................... 46 3.6: Digital Command Input ......................................................................................................................................................... 46 3.7: Stepnet Panel AC (STX) Analog Command Input................................................................................................................. 47 3.8: Digital Inputs......................................................................................................................................................................... 47 3.8.1: Stepnet Panel (STP) Digital Inputs .......................................................................................................................... 47 3.8.2: Stepnet Panel AC (STX) Digital Inputs..................................................................................................................... 48 3.9: Digital Outputs...................................................................................................................................................................... 49 3.10: Encoder Power Supply Output............................................................................................................................................ 49 3.11: Incremental Quadrature Encoder Inputs ............................................................................................................................. 50 3.11.1: Incremental Differential Encoder Inputs ................................................................................................................. 50 3.11.2: Stepnet Panel AC (STX) Single Ended Encoder Inputs ......................................................................................... 50 3.12: Stepnet Panel AC (STX) Multi-Mode Port ........................................................................................................................... 51 3.13: Serial Interface ................................................................................................................................................................... 51 3.14: CAN Interface ..................................................................................................................................................................... 51 3.15: Status Indicators................................................................................................................................................................. 52 3.16: Fault Levels ........................................................................................................................................................................ 52 3.17: Power Dissipation ............................................................................................................................................................... 52 3.17.1: Stepnet Panel (STP) Power Dissipation................................................................................................................. 52 3.17.2: Stepnet Panel AC (STX) Power Dissipation ........................................................................................................... 52 3.18: Thermal Impedance............................................................................................................................................................ 52 3.19: Mechanical and Environmental ........................................................................................................................................... 53 3.20: Dimensions......................................................................................................................................................................... 54 3.20.1: Stepnet Panel (STP) Dimensions .......................................................................................................................... 54 3.20.2: Stepnet Panel AC (STX) Dimensions..................................................................................................................... 55 Copley Controls Corp. 43 Specifications Stepnet Panel Amplifier User Guide 3.1: Agency Approvals Stepnet Panel (STP) and Stepnet Panel AC (STX) Agency Approvals CE Compliance: EN 55011, 2007 • CiSPR 11 : 2003/A2 : 2006 • Limits and Methods of Measurement of Radio Disturbance Characteristics of Industrial, Scientific, and Medical (ISM) Radio Frequency equipment EN 61000-6-1 : 2007 • Electromagnetic Compatibility generic immunity Requirements (Following the provisions of EC Directive 2004/108/EC [EMC Directive]) EN 61010-1 : 2001 • Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory use. (Following the provisions of EC Directive 2006/95/EC [Low Voltage Directive]) UL 508C 3rd Ed.: 2002 UL Standard for Safety for Power Conversion Equipment UL 61010-1 2nd Ed.: 2004 Safety Requirements for Electrical Equipment for Measurement, Control and Laboratory Use 3.2: Power Input 3.2.1: Stepnet Panel (STP) Power Input Specification Model STP-075-10 STP-075-07 HV min to HV max +20 to +75 Vdc, transformer-isolated Peak current 8 Adc (1 Sec) 11 Adc Continuous current 5.5 Adc 11 Adc Auxiliary power (optional) +20 to +75 Vdc 3W typical when auxiliary power > HV 0W when auxiliary power < HV 3.2.2: Stepnet Panel AC (STX) Power Input Specification Mains voltage Mains frequency Mains current Logic supply (required) 44 STX-115-07 100 – 120 Vac Model STX-230-07 100 – 240 Vac 50-60 Hz 8 Arms, continuous 20-32 Vdc @ 500 mAdc maximum Copley Controls Stepnet Panel Amplifier User Guide Specifications 3.3: Power Output 3.3.1: Stepnet Panel (STP) Power Output Specification Boost / peak current STP-075-07 Model STP-075-10 7 Adc (5 Arms, sinusoidal) ± 5% 10 Adc (7 Arms, sinusoidal) ± 5% Boost / peak time 1 Sec n/a Run / continuous current 5 Adc (3.54 Arms, sinusoidal)± 5% 10 Adc (7 Arms, sinusoidal) ± 5% Efficiency 97% @ Full rated voltage and continuous output current. 3.3.2: Stepnet Panel AC (STX) Power Output Specification Boost / peak current STX-115-07 Model STX-230-07 7 Adc (5 Arms, sinusoidal) ± 5% 7 Adc (5 Arms, sinusoidal) ± 5% Boost / peak time 1 Sec 1 Sec Run / continuous current 5 Adc (3.54 Arms, sinusoidal) ± 5% 5 Adc (3.54 Arms, sinusoidal) ± 5% Efficiency 97% @ Full rated voltage and continuous output current. (Note 2) NOTES: 1. Current ratings are for current vector produced by currents flowing in A and B phases (90º phase difference between phases). 2. Mounting to heat sink required for operation at continuous current. 3.3.3: Power Output Configuration (STP and STX) Type Dual MOSFET H-bridges, 15 kHz center-weighted PWM, space-vector modulation PWM ripple frequency 30 kHz Minimum load inductance STX > 200 µH per phase STP > 400 µH per phase Note: Contact factory if lower inductance is required. Copley Controls Corp. 45 Specifications Stepnet Panel Amplifier User Guide 3.4: Control Loops Type Servo mode: current Servo mode: velocity 100% digital. Stepper or servo mode: position Sampling rate (time) Servo mode: current 15 kHz (67 Xs) Servo mode: velocity 3 kHz (333 Xs) Stepper or servo mode: position 3 kHz (333 Xs) Current loop small signal bandwidth > 2 kHz (Tuning and load impedance dependent) Servo mode velocity loop filters Type Programmable Low Pass, 1 Pole Low Pass, Butterworth, 2 Poles Bi-Quadratic, 2 Poles & 2 Zeros Frequency range Programmable 20 - 1500 Hz Voltage compensation Changes in HV or Mains voltage does not affect current-loop bandwidth 3.5: Stepnet Panel AC (STX) Internal Regen Circuit Specification Type STX-115-07 Model STX-230-07 Internal MOSFET dissipater Continuous power 40 W Peak power 80 W Turn on voltage(± 2%) Bus voltage > 195 Vdc Bus voltage > 390 Vdc Turn off voltage(± 2%) Bus voltage < 190 Vdc Bus voltage < 380 Vdc 3.6: Digital Command Input Step and direction, Count up/ count down maximum rate STP = 1 MHz max pulse rate Quadrature A/B encoder maximum rate 5 M line/sec (20 M count/sec after quadrature) Digital current & velocity command PWM frequency range 1 kHz - 100 kHz Servo mode only PWM minimum pulse width 220 nSec Digital position command Stepper or servo mode 46 STX = 1.5 MHz max pulse rate Copley Controls Stepnet Panel Amplifier User Guide Specifications 3.7: Stepnet Panel AC (STX) Analog Command Input Channels 1 Type Differential, non-isolated Measurement range ±10 Vdc Maximum voltage Differential ±10 Vdc Input to Ground ±10 Vdc Input impedance 5k Resolution 12 Bit Accuracy ± 2% of reading, ± 0,5% of range Bandwidth 7 kHz Sample period 200 µSec Function Current, velocity, or position commands. Analog input filter Programmable: Type Low Pass, 1 Pole Low Pass, Butterworth, 2 Poles Bi-Quadratic, 2 Poles & 2 Zeros Programmable: 20 - 1500 Hz Frequency range 3.8: Digital Inputs 3.8.1: Stepnet Panel (STP) Digital Inputs Channels 12 5 general-purpose 7 high-speed Function IN1 dedicated to enable input function IN2 - IN12 programmable Logic low input voltage < +1.35 Vdc Logic high input voltage > +3.65 Vdc Scan time 333 µSec (pulse and direction, PWM input, and secondary encoder are handled at DSP clock rate of 25 nSec) Debounce Digital, programmable from 0 - 10,000 mSec General purpose inputs 1 - 5 Type 74HC14 Schmitt trigger w/ RC filter Inputs 1 – 4, RC time constant = 33uSec Input 5, RC time constant = 22uSec 10 k resistor programmable as pull down or pull up to internal +5 Vdc. Input voltage range 0 V - +30 Vdc Type 74HC14 Schmitt trigger w/ RC filter RC time constant = 0.1uSec 10 k resistor programmable as pull down or pull up to internal +5 Vdc. Input voltage range 0 V - +12 Vdc High speed inputs 6 - 12 Copley Controls Corp. 47 Specifications Stepnet Panel Amplifier User Guide 3.8.2: Stepnet Panel AC (STX) Digital Inputs Channels 12 7 general-purpose 5 high-speed Function IN1 dedicated to enable input function IN2 – 11 programmable IN12 motor over temperature, may be reprogrammed Scan time 333 µSec (pulse and direction, PWM input, and secondary encoder are handled at DSP clock rate of 25 nSec) Debounce Digital, programmable from 0 - 10,000 mSec General purpose inputs 1 – 4, 10 ,11 Type 74HC14 Schmitt trigger w/ RC filter RC time constant = 330uSec 10 k resistor programmable as pull down or pull up to internal +5 Vdc. High speed input 5 Input voltage range 0 V - +24 Vdc Logic low input voltage < +1.35 Vdc Logic high input voltage > +3.65 Vdc Type 74HC14 Schmitt trigger w/ RC filter RC time constant = 0.1uSec 10 k resistor programmable as pull down or pull up to internal +5 Vdc. High speed inputs 6 -9 Input voltage range 0 V - +12 Vdc Logic low input voltage < +1.35 Vdc Logic high input voltage > +3.65 Vdc Type RS422 line receiver w/ RC Filter RC time constant = 0.1 uSec 10 k resistor programmable as pull down or pull up to internal +5 Vdc. May be programmed as 4 independent inputs or 2 differential inputs General purpose input 12 Input voltage range 0 V - +12 Vdc Logic low input voltage < +2.30 Vdc Logic high input voltage > +2.45 Vdc Type 74HC14 Schmitt trigger w/ RC filter RC time constant = 500uSec 5k 48 resistor pull up to internal +5 Vdc. Input voltage range 0 V - +24 Vdc Logic low input voltage < +1.35 Vdc Logic high input voltage > +3.65 Vdc Copley Controls Stepnet Panel Amplifier User Guide Specifications 3.9: Digital Outputs Channels 4 Type STP 1 – 4 STX 1 – 3 Current-sinking MOSFET, open-drain with 1 k through diode STX 4 (Brake) Opto-isolated, current sinking MOSFET with flyback diode to 24Vdc Maximum voltage +30 Vdc Low level output resistance < 0.1 Function Programmable pullup to internal +5 Vdc Maximum sink current STP 1 - 4 1A, Total current of outputs 1 – 4 not to exceed 2A STX 1 – 3 1A, Total current of outputs 1 - 3 not to exceed 1A STX 4 1A 3.10: Encoder Power Supply Output Voltage output +5 Vdc ±5% Maximum current output 250 mA Short circuit protection, STX only Fold-back current limiting Note: collapsing this supply will put the amplifier in a fault condition. Function Provides power for motor encoder. Copley Controls Corp. 49 Specifications Stepnet Panel Amplifier User Guide 3.11: Incremental Quadrature Encoder Inputs 3.11.1: Incremental Differential Encoder Inputs Channels 3 Type Differential RS-422 line receiver, Non-isolated RC filter Signals A, /A, B, /B, X*, /X* Common mode Vin range ±7 Vdc Differential input threshold ±0.2 Vdc Differential input impedance 121 Maximum frequency 5 MHz Line (20 Mcount/sec) Function Incremental encoder required for servo mode of operation or for position monitoring and correction in stepper mode. * X is equivalent to Marker, Index, or Z channels, depending on the encoder manufacturer. This channel is only required in certain homing modes. 3.11.2: Stepnet Panel AC (STX) Single Ended Encoder Inputs Channels 3 Type Single ended 5V CMOS, Non-isolated RC filter, 2 K pull up to 5V Signals A, B, X* Vin Low <1.35 V Vin High >3.65 V Vin Maximum +10 Vdc Vin Minimum -7 Vdc Maximum frequency 1 MHz Line (4 Mcount/sec) Function Incremental encoder required for servo mode of operation or for position monitoring and correction in stepper mode. * X is equivalent to Marker, Index, or Z channels, depending on the encoder manufacturer. This channel is only required in certain homing modes. 50 Copley Controls Stepnet Panel Amplifier User Guide Specifications 3.12: Stepnet Panel AC (STX) Multi-Mode Port Channels 3 Type Bi-Directional, differential RS-422 Non-isolated Signals A, /A, B, /B, X, /X Common mode Vin range ±7 Vdc Differential input threshold ±0.2 Vdc Termination resistance None Function Programmable Output Mode Buffered primary incremental encoder Input Mode Current / velocity mode, PWM input Position mode, digital command input Maximum frequency Output mode Buffered encoder 5 MHz Line (20 Mcount/sec) Input Mode PWM input Digital command 100Khz 5 MHz (50% Duty Cycle) 3.13: Serial Interface Channels 1 Type RS-232 Signals Rxd, Txd, Gnd Baud rate 9,600 to 115,200 (defaults to 9600 on power up or reset) Data format N, 8, 1 Protocol Binary or ASCII format Function Amplifier set up, control, and diagnostics 3.14: CAN Interface Channels 1 (optically isolated from amplifier circuits) Connectors 2 eight-position modular (RJ-45 style) wired as per CAN Cia DR-303-1, V1.1 One connector for signal input. Second connector for daisy chaining to next node. Signals CAN H, CAN L, CAN Gnd (CAN Power Pass though only) Format CAN V2.0b physical layer for high-speed connections compliant Protocol Motion Control Device Under DSP-402 of the CANopen DS-301 V4.01 (EN 50325-4) Application Layer Supported modes Profile Torque, Profile Velocity, Profile Position, Interpolated Position, and Homing Node address selection 16-position rotary switch on front panel OR programmable digital inputs OR stored in flash memory OR combination of above. Bus termination External 121 resistor across CAN-H and CAN-L when termination plug is installed in second connector. Function Real-time motion control Copley Controls Corp. 51 Specifications Stepnet Panel Amplifier User Guide 3.15: Status Indicators Amplifier status Stepnet Panel (STP): LED is integrated in connector J5. Stepnet Panel AC (STX): LED on front panel. CAN status Stepnet Panel (STP): LED is integrated in connector J6. Stepnet Panel AC (STX): LED is integrated in connector J4 Conforms to CAN Indicator Specification CiA DR-303-3. 3.16: Fault Levels Amp over temperature > 70 °C DC bus under voltage Stepnet Panel (STP): < +20 Vdc Stepnet Panel AC (STX): < +60 Vdc DC bus over voltage Stepnet Panel (STP): > +90 Vdc Stepnet STX -115-07: > +200 Vdc Stepnet STX-230-07: > +400 Vdc Encoder power STX only <4.55 Vdc 3.17: Power Dissipation 3.17.1: Stepnet Panel (STP) Power Dissipation STP-075-07 Output Current +HV 0 Adc 75 Vdc 3W Maximum continuous 25 Vdc 6.0 W 75 Vdc 7.5 W STP-075-10 Dissipation 3.17.2: Stepnet Panel AC (STX) Power Dissipation STX-115-07 STX-230-10 Output Power 0 Adc 1W 4W Maximum continuous 30W 40W 3.18: Thermal Impedance See C: Thermal Considerations (p. 173). 52 Copley Controls Stepnet Panel Amplifier User Guide Specifications 3.19: Mechanical and Environmental Stepnet Panel (STP) Stepnet Panel AC (STX) 5.35 x 3.51 x 1.65 [135.9 x 89.3 x 41.8] 5.73 x 4.70 x 2.17 [145.5 x 119.5 x 55.0] See Stepnet Panel (STP) Dimensions (p. 54) See Stepnet Panel AC (STX) Dimensions (p. 55) Without heat sink 0.94 lb (0.43 kg) 1.73 lb (0.79 kg) With heat sink 1.34 lb (0.61 kg) 2.65 lb (1.20 kg) Storage -40 to +85°C -40 to +85 °C Operating 0 to +50°C 0 to 45 °C Size; inches [mm] (without heatsink) Weight Ambient temperature Humidity 0% to 95%, non-condensing Contaminants Pollution degree 2 Environment IEC68-2: 1990 Cover material Meets U.L. Spec 94 V-0 Flammability Rating Copley Controls Corp. 53 Specifications Stepnet Panel Amplifier User Guide 3.20: Dimensions 3.20.1: Stepnet Panel (STP) Dimensions Optional heatsink shown 54 Copley Controls Stepnet Panel Amplifier User Guide Specifications 3.20.2: Stepnet Panel AC (STX) Dimensions Optional heatsink shown Copley Controls Corp. 55 Specifications 56 Stepnet Panel Amplifier User Guide Copley Controls CHAPTER 4: WIRING This chapter describes the wiring of amplifier and motor connections. Contents include: Title Page 4.1.1: Stepnet Panel (STP) General Wiring Instructions .............................................................................................................. 58 4.1.2: Stepnet Panel (STP) Connector Locations ........................................................................................................................ 59 4.1.3: Stepnet Panel (STP) Power (J1)........................................................................................................................................ 60 4.1.4: Stepnet Panel (STP) Motor (J2)......................................................................................................................................... 61 4.1.5: Stepnet Panel (STP) Signal (J3)........................................................................................................................................ 62 4.1.6: Stepnet Panel (STP) CAN Bus (J5 and J6)........................................................................................................................ 65 4.1.7: Stepnet Panel (STP) RS-232 Serial Communications (J4) ................................................................................................ 66 4.2.1: Stepnet Panel AC (STX) General Wiring Instructions ........................................................................................................ 67 4.2.2: Stepnet Panel AC (STX) Connector Locations................................................................................................................... 69 4.2.3: Stepnet Panel AC (STX) Power (J1) .................................................................................................................................. 70 4.2.4: Stepnet Panel AC (STX) Motor (J2) ................................................................................................................................... 71 4.2.5: Stepnet Panel AC (STX) Aux HV and Brake (J3)............................................................................................................... 72 4.2.6: Stepnet Panel AC (STX) CAN Bus (J4 and J5).................................................................................................................. 73 4.2.7: Stepnet Panel AC (STX) Feedback (J6) ............................................................................................................................ 74 4.2.8: Stepnet Panel AC (STX) Control (J7)................................................................................................................................. 78 4.2.9: Stepnet Panel AC (STX) J7 Digital Inputs Wiring Diagram ................................................................................................ 80 4.2.10: Stepnet Panel AC (STX) RS-232 Serial Communications (J8)......................................................................................... 83 Copley Controls Corp. 57 Wiring Stepnet Panel Amplifier User Guide 4.1: Stepnet Panel (STP) Wiring 4.1.1: Stepnet Panel (STP) General Wiring Instructions Stepnet Panel (STP) Electrical Codes and Warnings Be sure that all wiring complies with the National Electrical Code (NEC) or its national equivalent, and all prevailing local codes. DANGER: Hazardous voltages. ! Exercise caution when installing and adjusting. Failure to heed this warning can cause equipment damage, injury, or death. DANGER Stepnet Panel (STP) Shielding and Grounding Considerations Amplifier Auxillary Power Supply (optional) RS232 Circuit J4 Serial + J1 Power - DC/DC Converter AUX +HV GND + DC Power Supply - I/O Circuit Controller Encoder Circuit Encoder 5V 250 ma Connections to system ground should be kept as short as possible. J5 & J6 CAN CAN Network Isolation Barrier CAN Bus Transceiver 9 J3 Signal PWM Inverter Motor J2 Motor As shown above, power and control circuits in the Stepnet share a common circuit-ground. Digital inputs are referenced to this common circuit-ground, as are the digital outputs, encoder inputs, and serial communications port. The CAN ports are electrically isolated from this common circuitground. The Stepnet case (Chassis Ground) is also isolated from any of the internal circuits. The Stepnet "Gnd" terminal on the power connector (J1-4) should be connected to the users’ system common ground, through the shortest path, so that signals between the controller and the Stepnet are at the same common potential, and to minimize noise. The system common ground should, in turn, be connected to an earthing conductor by the shortest wire possible so that the whole system is referenced to “earth.” The HV power supply should be connected to the system common ground only at the Stepnet power connector. In this way, voltage drops across the power conductors due to high motor currents will not appear at the Stepnet ground, but at the HV power supply negative terminal where they will have less effect. Connection to the case is provided on the Chassis Ground terminal of the power connector (J1-1). This terminal should connect to the system chassis ground, keeping the wire as short as possible. 58 Copley Controls Stepnet Panel Amplifier User Guide Wiring This maximizes the shielding effect of the case, and provides a path to ground for noise currents that may occur in the cable shields. Stepnet Panel (STP) Shielding It is recommended that connections to the Stepnet motor, power and signal connectors be made using shielded cables. Shields on cables reduce emissions from the amplifier and help protect internal circuits from interference due to external sources of electrical noise. The shields shown in the wiring diagrams are also required for CE compliance. Cable shields should be tied to earth or system ground. Provisions are made on each Stepnet connector for connecting the shield to the chassis ground of the Stepnet which in turn is connected to the system ground. 4.1.2: Stepnet Panel (STP) Connector Locations Connector locations are shown below. J3: Signal J2: Motor J4: RS-232 J5: CAN J6: CAN J1: Power S1: CAN Address Switch Copley Controls Corp. 59 Wiring Stepnet Panel Amplifier User Guide 4.1.3: Stepnet Panel (STP) Power (J1) Stepnet Panel (STP) J1 Mating Connector Description Receptacle, Single Row 4 Position Manufacturer part numbers Housing; Molex 39-01-4041 Crimp Terminal: Molex 39-00-0039 (4 required) Wire size 18 - 24 AWG Connector housing and terminals are included in connector kit STP-CK Stepnet Panel (STP) J1 Pin Description Pin Signal Function 1 Chassis Ground Earth ground connection 2 Aux HV Auxiliary power input 3 +HV Power input 4 Ground Power common Stepnet Panel (STP) J1 Power Input Wiring Diagram Amplifier J1-1 J1-2 HV Bus J1-3 J1-4 Logic Supply + J1 - Aux Auxiliary Power Supply (optional) + +HV DC Power Supply Gnd Note 1 Note 1: Diode and capacitor should be installed if using a switching power supply. 60 Copley Controls Stepnet Panel Amplifier User Guide Wiring 4.1.4: Stepnet Panel (STP) Motor (J2) Stepnet Panel (STP) J2 Mating Connector Description Receptacle, Single Row 5 Position Manufacturer part numbers Housing; Molex 39-01-4051 Crimp Terminal: Molex 39-00-0039 (5 required) Wire Size 18 - 24 AWG Connector housing and terminals are included in connector kit STP-CK Stepnet Panel (STP) J2 Pin Description Pin Signal Function 1 Chassis Ground Motor frame ground and cable shield 2 Motor B- Phase B- output of amplifier 3 Motor B+ Phase B+ output of amplifier 4 Motor A- Phase A- output of amplifier 5 Motor A+ Phase A+ output of amplifier Stepnet Panel (STP) J2 Motor Wiring Diagram Typical wiring for a 4-lead motor: Amplifier J2 J2-1 J2-2 J3-3 J2-4 J2-5 Case Ground Motor BB+ B A- B A+ A A Typical wiring alternatives: 8-lead motor, coils in parallel B 8-lead motor, coils in series 6-lead motor B B No Connection B B B No Connection A Copley Controls Corp. A A A A A 61 Wiring Stepnet Panel Amplifier User Guide 4.1.5: Stepnet Panel (STP) Signal (J3) Stepnet Panel (STP) J3 Mating Connector Description Plug, High Density D-Sub, 26 Position Manufacturer Part numbers Connector, solder cup; Norcomp 180-026-102-001 Backshell: Norcomp: 979-015-020R121 Wire Size 22 - 26 AWG, shielded cable Connector and backshell are included in connector kit STP-CK. Amplifier pin locations are shown here: 9 1 18 10 26 19 Stepnet Panel (STP) J3 Pin Description Pin Signal Function Speed Pull-Up/Pull-Down Group 1 IN1 Enable Standard Group 1 2 IN2 Programmable Standard Group 1 3 IN3 Programmable Standard Group 1 4 IN4 Programmable Standard Group 2 5 Encoder A Motor incremental encoder input 6 Encoder /A 7 Signal Ground Signal ground reference for input, outputs and Encoder +5V 8 OUT1 General-purpose, programmable output 9 Frame Ground Frame Ground 10 IN5 Programmable Standard Group 2 11 IN6 Mode Dependent High Group 3 12 IN7 Mode Dependent High Group 3 13 IN8 Mode Dependent High Group 3 14 Encoder B Motor incremental encoder input 15 Encoder /B 16 +5V OUT Encoder +5 Vdc power supply output. Total load current not to exceed 250 mA. 17 OUT2 General-purpose, programmable output 18 OUT4 19 IN9 Mode Dependent High Group 4 20 IN10 Mode Dependent High Group 4 21 IN11 Mode Dependent High Group 4 22 IN12 Mode Dependent High Group 4 23 Encoder X Motor incremental encoder input 24 Encoder /X 25 Signal Ground Signal ground reference for input, outputs and encoder +5V 26 OUT3 General-purpose, programmable output 62 Copley Controls Stepnet Panel Amplifier User Guide Wiring Stepnet Panel (STP) J3 Mode-Dependant Dedicated Inputs These inputs are dedicated to specific functions, depending on operating mode. Mode Input Function All IN1 Enable Current & Velocity IN9 PWM Input Current & Velocity IN9 PWM Input PWM 100% IN10 Direction Input Position IN9 Pulse Input Pulse & Direction IN10 Direction Input PWM 50% Position IN9 Count Up Up/Down IN10 Count Down Position IN9 Channel B Quadrature IN10 Channel A Stepnet Panel (STP) J3 Input Wiring Diagram J3 Amplifier J3-1 Typical Circuit + 5 Vdc R1 pull up / pull dow n J3-2 J3-3 J3-4 R2 J3-10 J3-11 J3-12 74HC14 C J3-13 J3-19 J3-20 J3-21 J3-22 J3-25 IN1 (Enable) IN2 Motion Controller IN3 IN4 IN5 IN6 IN7 IN8 IN9 (Pulse) IN10 (Direction) IN11 IN12 Signal Ground Standard inputs (IN1-IN4): R1 = 10 K , R2 = 10 K , C = 3300 pƒ High speed input (IN6-IN12): R1 = 10 K , R2 = 1 K , C = 100 pƒ IN5: R1 = 4.99 K , R2 = 10 K , C = 2200 pƒ Copley Controls Corp. 63 Wiring Stepnet Panel Amplifier User Guide Stepnet Panel (STP) J3 Digital Outputs Wiring Diagram J3 Amplifier Typical Output Loads + 5 Vdc Typical Circuit Relay 1K J3-8 J3-17 J3-26 J3-18 J3-25 OUT1 OUT2 * Lamp Motion Controller OUT3 External Power Supply OUT4 Signal Ground * Flyback diode required for inductive loads Stepnet Panel (STP) J3 Incremental Encoder Wiring Diagram Amplifier J3 Typical Circuit 1K J3-5 J3-6 + - 22 pƒ 121 1K J3-14 J3-15 J3-23 22 pƒ J3-24 5V @ 250 mA J3-16 J3-7 A A A A B B B B X Index X Index + 5 VDC Gnd J3-9 Frame Gnd 64 Incremental Encoder Encoder Power Case Ground Copley Controls Stepnet Panel Amplifier User Guide Wiring 4.1.6: Stepnet Panel (STP) CAN Bus (J5 and J6) Stepnet Panel (STP) J5 and J6 Mating Connector 8-position, modular connector (RJ-45 style). Copley Controls provides the following assemblies: • Prefabricated 10 foot cable, PN STP-NC-10 • Prefabricated 1 foot cable, PN STP-NC-01 • Terminator Plug, PN STP-NT A diagram of the female connector is shown below. 1 2 3 4 5 6 7 8 Stepnet Panel (STP) J5 and J6 Pin Description Pin Signal Function 1 CAN_H CAN_H bus line (dominant high) 2 CAN _L CAN_L bus line (dominant low) 3 CAN_Gnd Ground / 0 V / V- 4 -- Pass though to second connector, no internal connection 5 -- Pass though to second connector, no internal connection 6 CAN_SHLD Pass though to second connector, no internal connection 7 CAN_Gnd Ground / 0 V / V- 8 CAN V+ Pass through to second connector, no internal connection Stepnet Panel (STP) CAN Bus Wiring Diagram Amplifier Opto-isolation J5 J5-1 J5-2 J5-3 J5-4 J5-5 J5-6 J5-7 J5-8 CAN + CAN CAN Gnd CAN Network J6 J6-1 J6-2 J6-3 J6-4 J6-5 J6-6 J6-7 J6-8 Copley Controls Corp. CAN + CAN CAN Gnd CAN Network Note 1: If this is the last amplifier on the network, use Copley Terminator Plug PN STP-NT to terminate the bus. 65 Wiring Stepnet Panel Amplifier User Guide 4.1.7: Stepnet Panel (STP) RS-232 Serial Communications (J4) Stepnet Panel (STP) J4 Mating Connector 6-position, modular connector (RJ-11 style). Copley Controls provides a prefabricated cable and modular-to-9-pin sub-D adapter in RS-232 Serial Cable Kit, PN SER-CK. A diagram of the female connector is shown below. 1 2 3 4 5 6 Stepnet Panel (STP) J4 Pin Description Pin Signal Function 1 N/C No connection 2 RxD Receive data input from computer 3 Signal ground Power supply ground 4 Signal ground Power supply ground 5 TxD Transmit data output to computer 6 N/C No connection Stepnet Panel (STP) J4 RS-232 Serial Communications Wiring Diagram Amplifier J4 J4-6 J4-5 J4-4 J4-3 J4-2 Tx D ground ground Rx D To PC RS-232 Port J4-1 66 Copley Controls Stepnet Panel Amplifier User Guide Wiring 4.2: Stepnet Panel AC (STX) Wiring 4.2.1: Stepnet Panel AC (STX) General Wiring Instructions Stepnet Panel AC (STX) Electrical Codes and Warnings Be sure that all wiring complies with the National Electrical Code (NEC) or its national equivalent, and all prevailing local codes. ! DANGER: Hazardous voltages. Exercise caution when installing and adjusting. Failure to heed this warning can cause equipment damage, injury, or death. DANGER ! Risk of electric shock. High-voltage circuits on J1 and J2 are connected to mains power. Failure to heed this warning can cause equipment damage, injury, or death. DANGER ! WARNING ! WARNING Copley Controls Corp. Do not ground mains-connected circuits. With the exception of the ground pins on J1 and J2, all of the other circuits on these connectors are mains-connected and must never be grounded. Failure to heed this warning can cause equipment damage. Do not plug or unplug connectors with power applied. The connecting or disconnecting of cables while the amplifier has 24Vdc and/or mains power applied is not recommended. Failure to heed this warning may cause equipment damage. 67 Wiring Stepnet Panel Amplifier User Guide Power and Grounding Diagram: Stepnet Panel AC (STX) AMPLIFIER CHASSIS A+ DC BUSS(+) J1 L1 MAINS L2 + ~ A- + PWM INVERTER REGEN ~ - FRAME (SAFETY) GROUND J2 MOTOR B+ B- DC BUSS(-) J3 CASE PWM STAGE CONTROL POWER +24 Vdc ISOLATION BARRIER +24 VDC BRAKE BRAKE DC/DC Cntrl RTN +24 Vdc GROUND CAN NETWORK DC/DC Converter J4 & 5 CONTROL SYSTEM LOGIC & SIGNAL POWER +5 Vdc @ 250mA CAN Bus Ckt SHIELD +5 Vdc ENCODER +5 Vdc J7 ENABLE [IN1] J6 CONTROL LOGIC SIGNAL GND SIGNAL GND CONTROL SIGNAL GROUND Stepnet Panel AC (STX) Primary Grounding Functions A grounding system has three primary functions: safety, voltage-reference, and shielding. Stepnet Panel AC (STX) J1-2 Primary Ground The primary ground at J1-2 is the safety ground and is intended to carry the fault currents from the mains in the case of an internal failure or short-circuit of electronic components. This ground is connected to the amplifier chassis. Wiring to this ground should be done using the same gauge wire as that used for the mains. This wire is a “bonding”’ conductor that should be connected to an earthed ground point and must not pass through any circuit interrupting devices. The pin on the amplifier at J1-2 is longer than the other pins on J1, giving it a first-make, lastbreak action so that the amplifier chassis is never ungrounded when the mains power is connected. 68 Copley Controls Stepnet Panel Amplifier User Guide Wiring Stepnet Panel AC (STX) J2 Ground The ground terminal at J2-1 also connects to the amplifier chassis. Motor cases can be safety-grounded in one or optionally both of these ways: • Direct grounding of the motor frame (assuming the frame of the machine is grounded). Attach the metal motor case to the metal machine frame or connect the ground wire of the motor to the metal frame of the machine. • Grounding of the motor frame through the motor power cable to amplifier J2-1. The ground wire should be of the same gauge as the power wires. Cable shields, because of their smaller wire size, must not be used as part of a safety-ground system. Stepnet Panel AC (STX) Signal Grounding The amplifier signal ground must be connected to the control system signal ground. The amplifier signal ground is not connected to earth ground internal to the amplifier. Therefore, the control system signal ground can be connected to earth ground without introducing a ground loop. Stepnet Panel AC (STX) Shielding Shields on cables reduce emissions from the amplifier and help protect internal circuits from interference due to external sources of electrical noise. The shields shown in the wiring diagrams are also required for CE compliance. Cable shields should be tied at both ends to earth or chassis ground. The housing and pin 1 of both J6 and J7 are connected to the amplifier’s chassis. 4.2.2: Stepnet Panel AC (STX) Connector Locations Connector locations are shown below. Copley Controls Corp. 69 Wiring Stepnet Panel Amplifier User Guide 4.2.3: Stepnet Panel AC (STX) Power (J1) Stepnet Panel AC (STX) J1 Mating Connector Description Plug, 3 position, 7.5 mm, female Manufacturer Part numbers Wago 721-203/026-045/RN01-0000 Insert/extract lever: Wago 231-131 Wire size 12 AWG maximum Connector housing and terminals are included in connector kit STX-CK Stepnet Panel AC (STX) J1 Pin Description Pin Signal Function 1 L1 AC power input (hot or L1) 2 Frame ground Chassis safety ground 3 L2 AC power input (neutral or L2) Stepnet Panel AC (STX) J1 AC Mains Fuse Recommendation Recommended fuse type: Class CC, 600 Vac rated, Ferraz-Shawmut ATDR, Littelfuse CCMR, Bussman LP-CC, or equivalent. Stepnet Panel AC (STX) J1 AC Mains Wiring Diagram (Single-Phase) Amplifier J1 J1-1 J1-2 J1-3 Fuses** L1 L2 L1 (Line) L O A D Line Filter* L I N E L2 (Neut) 1Ø 47-63 Hz 100-240 VAC Earth Ground Keep wire length as short as possible. Not to exceed 1 Meter. * Corcom 10VN1 (or equivalent) used for CE compliance ** Not required on a neutral line. Note: A clamp-on ferrite (Fair-Rite PN 0431164951) was used on the AC input cable between the filter and drive (single turn) to meet EMC requirements during qualification testing. 70 Copley Controls Stepnet Panel Amplifier User Guide Wiring 4.2.4: Stepnet Panel AC (STX) Motor (J2) Stepnet Panel AC (STX) J2 Mating Connector Description Receptacle, Single Row 5 Position Manufacturer Part numbers Wago: 721-605/000-043/RN01-0000 Insert/extract lever: Wago: 231-131 Wire Size 28 - 12 AWG Connector housing and terminals are included in connector kit STX-CK Stepnet Panel AC (STX) J2 Pin Description Pin Signal Function 1 Frame Ground Motor frame ground and cable shield 2 Motor /B Phase B- output of amplifier 3 Motor B Phase B+ output of amplifier 4 Motor /A Phase A- output of amplifier 5 Motor A Phase A+ output of amplifier Stepnet Panel AC (STX) J2 Motor Wiring Diagram Typical wiring for a 4-lead motor: Note: A clamp-on ferrite (Fair-Rite PN 0431164281) was used on the motor cable (single turn), installed close to the amplifier, to meet EMC requirements during qualification testing. Typical wiring alternatives: 8-lead motor, coils in parallel B 8-lead motor, coils in series 6-lead motor B B No Connection B B B No Connection A Copley Controls Corp. A A A A A 71 Wiring Stepnet Panel Amplifier User Guide 4.2.5: Stepnet Panel AC (STX) Aux HV and Brake (J3) Stepnet Panel AC (STX) J3 Mating Connector Description Plug, 3 position, 5.0 mm, female Manufacturer Part numbers Wago: 721-103/026-047/RN01-0000 Insert/extract lever: Wago: 231-131 Wire Size 12 AWG maximum Connector and backshell are included in connector kit STX-CK. Stepnet Panel AC (STX) J3 Pin Description Pin Signal Function 1 Return +24 Vdc return or common 2 Brake Output Return or low side of motor brake 3 +24 Vdc +24 Vdc Logic power supply Stepnet Panel AC (STX) J3 Logic Supply and Brake Wiring Diagram Amplifier J3 Isolated Logic Power Supply Brake J3-3 J3-2 J3-1 72 +24 V Brake RTN +24 Vdc Power Supply (Required) Copley Controls Stepnet Panel Amplifier User Guide Wiring 4.2.6: Stepnet Panel AC (STX) CAN Bus (J4 and J5) Stepnet Panel AC (STX) J4-5 Mating Connector 8-position, modular connector (RJ-45 style). Copley Controls provides the following assemblies: • Prefabricated 10 foot cable, PN STX-NC-10 • Prefabricated 1 foot cable, PN STX-NC-01 • Terminator Plug, PN STX-NT A diagram of the female connector is shown below. 1 2 3 4 5 6 7 8 Stepnet Panel AC (STX) J4-5 Pin Description* Pin Signal Function 1 CAN_H CAN_H bus line (dominant high) 2 CAN _L CAN_L bus line (dominant low) 3 CAN_Gnd Ground / 0 V / V- 4 -- Pass though to second connector, no internal connection 5 -- Pass though to second connector, no internal connection 6 CAN_SHLD Pass though to second connector, no internal connection 7 CAN_Gnd Ground / 0 V / V- 8 CAN V+ Pass through to second connector, no internal connection *Table applies to both J4 and J5 CAN connectors Stepnet Panel AC (STX) J4-5 CAN Bus Wiring Diagram Amplifier Opto-isolation J4 J4-1 J4-2 J4-3 J4-4 J4-5 J4-6 J4-7 J4-8 CAN + CAN CAN Gnd CAN Network J5 J5-1 J5-2 J5-3 J5-4 J5-5 J5-6 J5-7 J5-8 Copley Controls Corp. CAN + CAN CAN Gnd CAN Network Note 1: If this is the last amplifier on the network, use Copley Terminator Plug PN STX-NT to terminate the bus. 73 Wiring Stepnet Panel Amplifier User Guide 4.2.7: Stepnet Panel AC (STX) Feedback (J6) Stepnet Panel AC (STX) J6 Mating Connector Description 15 Position, High-Density D-Sub Male Solder Style Connector and backshell. Manufacturer Part numbers Norcomp: 180-015-103L001 connector Norcomp: 979-009-020R121 backshell Wire Size 24-30 AWG Connector and backshell are included in connector kit STX-CK. Pin connections are shown here: 1 6 11 J6 pin connections 5 10 15 74 Copley Controls Stepnet Panel Amplifier User Guide Wiring Stepnet Panel AC (STX) J6 Pin Description Pin Signal Function 1 Frame Ground Cable shield connection 2 +5 Vdc Encoder +5 Vdc power supply output. Total load current on J7-20 and J6-4 not to exceed 250 mA. 3 Encoder B2 Single-ended primary incremental encoder input. 4 +5 Vdc Encoder +5 Vdc power supply output. Total load current on J7-20 and J6-4 not to exceed 250 mA. 5 Signal Ground Signal and +5 Vdc ground 6 Encoder X2 Single-ended primary incremental encoder input. 7 Encoder /X Input 8 Encoder X Input Differential primary incremental encoder inputs 9 Encoder A2 Single-ended primary incremental encoder input. 10 [IN12] Motemp Motor over temperature switch Standard speed Pull-up/pull-down group 2 May be programmed to other functions 11 Encoder /B Input 12 Encoder B Input 13 Encoder /A Input 14 Encoder A Input 15 Signal Ground Differential primary incremental encoder inputs Signal and +5 Vdc ground Stepnet Panel AC (STX) J6 Quad A/B Incremental Encoder Wiring Diagram – With Index When the index pulse is used (as in most applications), wire the connection as shown here. Amplifier J6 Typical Circuit 1K J6-14 J6-13 + To Encoder Output 22 pƒ 121 1K J6-12 J6-11 J6-8 22 pƒ J6-7 5V @ 250 mA J6-4 J6-2 A A A A B B B B X Index X Index + 5 VDC Gnd J6-1 Frame Gnd Copley Controls Corp. Incremental Encoder Encoder Power Case Ground 75 Wiring Stepnet Panel Amplifier User Guide Stepnet Panel AC (STX) J6 Quad A/B Incremental Encoder Wiring Diagram – No Index In applications where the encoder index pulse is not used, wire the connector as shown here. Amplifier J6 J6-14 J6-13 J6-12 J6-11 J6-8 J6-7 J6-4 J6-2 A A A A B B B B X X + 5 VDC Gnd J6-1 Frame Gnd 76 Incremental Encoder Encoder Power Case Ground Copley Controls Stepnet Panel Amplifier User Guide Wiring Stepnet Panel AC (STX) J6 Single-Ended Encoder Wiring Diagram The Stepnet "Gnd" terminal on the feedback connector (J6-1) should be connected to the users’ system common ground, through the shortest path, so that signals between the controller and the Stepnet are at the same common potential, and to minimize noise. The system common ground should, in turn, be connected to an earthing conductor by the shortest wire possible so that the whole system is referenced to “earth.” Amplifier J6 + 5 Vdc Typical Circuit 2K 1K J6-3 J6-6 100 p 5V @ 250 mA J6-9 J6-4 A2 A B2 B X2 X 5 Vdc Gnd J6-2 J6-1 Encoder Encoder Power Frame Gnd Case Ground Stepnet Panel AC (STX) J6 Motor Over Temperature Wiring Diagram Amplifier +5 Vdc J6 4.99 K 4.99 K 74HC14 0.1 µƒ Motor Over Temperature Switch J6-10 J6-15 J6-1 Copley Controls Corp. IN12 Ground Frame Gnd Case Ground 77 Wiring Stepnet Panel Amplifier User Guide 4.2.8: Stepnet Panel AC (STX) Control (J7) Stepnet Panel AC (STX) J7 Mating Connectors Description Manufacturer PN Wire Size 26 Position, 0.1 x 0.09 High Density D-Sub Male, Solder Style Connector Norcomp 180-026103L001 24 - 30 AWG Back shell Norcomp 979-015020R121 Solder style connector included in Connector Kit PN STX-CK. Pin connections are shown here: 1 10 19 J7 pin connections 9 78 18 26 Copley Controls Stepnet Panel Amplifier User Guide Wiring Stepnet Panel AC (STX) J7 Pin Description Pin Signal Function 1 Frame Ground Cable shield connection 2 Ref - Input Analog command negative input 3 Ref + Input Analog command positive input 4 IN1 5 IN2 6 IN3 7 IN4 8 IN10 Enable Programmable inputs Speed Pull-Up/PullDown Standard Group 1 Standard Group 1 Standard Group 1 Standard Group 2 Standard Group 4 9 IN11 Standard Group 4 10 IN5 HS Group 3 11 IN6 HS Group 3 12 IN7 HS Group 3 13 IN8 HS Group 4 14 IN9 HS Group 4 15 Signal Ground 16 OUT1 17 OUT2 18 OUT3 19 Signal Ground Signal ground for +5Vdc, inputs and outputs 20 +5 Vdc +5 Vdc output. Total load current on J7-20, J6-2, and J6-4 not to exceed 250 mA. 21 Multi-Mode Port /X 22 Multi-Mode Port X 23 Multi-Mode Port /B Programmable differential input/output port. 24 Multi-Mode Port B See Mode-Dependant Dedicated Inputs (p. 80) 25 Multi-Mode Port /A 26 Multi-Mode Port A Copley Controls Corp. Mode-dependant. See Mode-Dependant Dedicated Inputs (p. 80) Signal ground reference for inputs and outputs Programmable outputs 79 Wiring Stepnet Panel Amplifier User Guide Mode-Dependant Dedicated Inputs These inputs are dedicated to specific functions, depending on operating mode. Selected Command Source Mode Function Digital Input Digital Input Multi-Mode Port Single Ended Differential Current & Velocity IN8 IN8(+) & IN6(-) A & /A PWM Input Current & Velocity IN8 IN8(+) & IN6(-) A & /A PWM Input PWM 100% IN9 IN9(+) & IN7(-) B & /B Direction Input Position IN8 IN8(+) & IN6(-) A & /A Pulse Input PWM 50% Pulse & Direction IN9 IN9(+) & IN7(-) B & /B Direction Input Position IN8 IN8(+) & IN6(-) A & /A Count Up Up/Down IN9 IN9(+) & IN7(-) B & /B Count Down Position IN9 IN8(+) & IN6(-) A & /A Channel A Quadrature IN8 IN9(+) & IN7(-) B & /B Channel B 4.2.9: Stepnet Panel AC (STX) J7 Digital Inputs Wiring Diagram J7 Amplifier Typical Circuit + 5 Vdc J7-4 10 K pull up / pull dow n J7-5 J7-6 J7-7 R* J7-8 J7-9 J7-10 C* J7-11 J7-12 J7-13 J7-14 J7-15 IN1 (Enable) IN2 Motion Controller IN3 IN4 IN11 IN12 IN6 IN7 IN8 IN9 IN10 Signal Ground * Standard input R = 10 K C = 0.033 µƒ High-speed input R = 1K C = 100 pƒ 80 Copley Controls Stepnet Panel Amplifier User Guide Wiring Stepnet Panel AC (STX) J7 Digital Outputs Wiring Diagram J7 Amplifier Typical Output Loads + 5 Vdc Typical Circuit Relay 1K J7-16 J7-17 J7-18 J7-15 OUT1 OUT2 OUT3 * Lamp Motion Controller External Power Supply Signal Ground * Flyback diode required for inductive loads Copley Controls Corp. 81 Wiring Stepnet Panel Amplifier User Guide Stepnet Panel AC (STX) J7 Multi-Mode Port Interface Diagram Amplifier J7 +5 Vdc Typical Circuit 1K 26C32 2K 1K 22pF X J7-22 B J7-23 22pF B J7-24 26C31 Motion Controller or Position Encoder X J7-21 A J7-25 A J7-26 Signal Ground J7-15 J7-1 Frame Gnd Stepnet Panel AC (STX) J7 Analog Input Wiring Diagram Amplifier J7 Motion Controller 5K 37.4 K + - 5.36 K 37.4 K J7-2 J7-3 J7-1 Ref - VCMD - Ref + VCMD + Frame Gnd 5K 82 Copley Controls Stepnet Panel Amplifier User Guide Wiring 4.2.10: Stepnet Panel AC (STX) RS-232 Serial Communications (J8) Stepnet Panel AC (STX) J8 Mating Connector 6-position, modular connector (RJ-11 style). Copley Controls provides a prefabricated cable and modular-to-9-pin sub-D adapter in RS-232 Serial Cable Kit, PN SER-CK. A diagram of the female connector is shown below. 1 2 3 4 5 6 Stepnet Panel AC (STX) J8 Pin Description Pin Signal Function 1 N/C No connection 2 RxD Receive data input from computer 3 Signal ground Power supply ground 4 Signal ground Power supply ground 5 TxD Transmit data output to computer 6 N/C No connection Stepnet Panel AC (STX) J8 RS-232 Serial Communications Wiring Diagram Amplifier J8 J8-6 J8-5 J8-4 J8-3 J8-2 Tx D ground ground Rx D To PC RS-232 Port J8-1 Copley Controls Corp. 83 Wiring 84 Stepnet Panel Amplifier User Guide Copley Controls CHAPTER 5: MODE SELECTION AND GENERAL SETUP The Stepnet amplifier can be operated in stepper mode or servo mode, as described below. Mode Features Stepper Amplifier operates as a traditional, open position loop, stepper drive. With the addition of encoder feedback, the amplifier can monitor and report actual motor position and provide encoder correction. Also a position-tracking window can be set up along with a programmable following error warning and fault. Servo Amplifier operates as a true, closed loop, servo amplifier controlling a stepper motor. In this mode, the amplifier can be configured to accept current, velocity, or position commands. Encoder feedback is required for all servo modes of operation. This chapter contains procedures required for and information relevant to all modes of operation. Start here to begin amplifier set up, and then continue as instructed to the appropriate modespecific chapter. To copy setup data from an existing Copley Controls axis file (.ccx), skip to Quick Copy Setup Procedure (p. 156). NOTE: In the procedures described in this chapter, CME 2 uses a serial connection to a single amplifier to set up that amplifier. As an alternative, the multi-drop feature allows CME 2 to use a single RS-232 serial connection to one amplifier as a gateway to other amplifiers linked together by CAN bus connections. For more information, see the CME 2 User Guide. Step Page 5.1: Warnings .............................................................................................................................................................................. 86 5.2: CME 2 Installation and Serial Port Setup.............................................................................................................................. 87 5.3: Prerequisites ........................................................................................................................................................................ 91 5.4: Basic Setup .......................................................................................................................................................................... 93 5.5: Motor Setup.......................................................................................................................................................................... 95 5.6: Amplifier Configuration ....................................................................................................................................................... 100 5.7: Command Input.................................................................................................................................................................. 110 Copley Controls Corp. 85 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.1: Warnings ! DANGER: Hazardous voltages. Exercise caution when installing and adjusting. Failure to heed this warning can cause equipment damage, injury, or death. DANGER ! Make connections with power OFF. Do not make connections to motor or drive with power applied. Failure to heed this warning can cause equipment damage. WARNING ! Spinning motor with power off may damage amplifier. Do not spin motors with power off. Voltages generated by a motor can damage an amplifier. Failure to heed this warning can cause equipment damage. WARNING 86 Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup 5.2: CME 2 Installation and Serial Port Setup 5.2.1: Requirements Computer Requirements Minimal hardware requirements: • CPU: Minimum: 400 MHZ* • RAM: Minimum: 128 MB* *Using the minimum requirements will allow CME 2 to run, but performance will be significantly reduced. Communication Requirements For serial communications: • • At least one standard RS-232 serial port or a USB port with a USB to RS-232 adapter. At least one serial communication cable. Available from Copley Controls. Copley Controls cable part number: SER-CK. For CAN communications: • • One Copley Controls CAN PCI network card (part number CAN-PCI-02). CME 2 also supports CAN network cards made by these manufacturers: KVaser, Vector, and National Instruments. One PC-to-amplifier CANopen network cable. Software Requirements Copley Controls CME 2 software, Version 5.2 or higher. Operating System Requirements Operating Systems Supported: Windows NT, 2000, XP. Vista users see Special Notes for Windows Vista Users. 5.2.2: Special Notes for Windows Vista Users When the CME 2 installer starts running under Windows Vista, a message will be displayed stating that an unidentified program is trying to access the computer. Click the button to allow the installer to continue, and CME 2 will be installed properly. On previous versions of Windows, the user data for CME 2 (like ccx, ccm, files, etc.) were stored in C:\Program Files\Copley Motion\CME 2. Because of Windows Vista security, the CME 2 user files are stored on Vista systems in C:\Users\Public\Public Documents\Copley Motion\CME 2. 5.2.3: Downloading CME 2 Software from Web (Optional) 5.2.3.1 Choose or create a folder where you will download the software installation file. 5.2.3.2 In an internet browser, navigate to http://www.copleycontrols.com/Motion/Downloads/index.html Under Software Releases, click on CME 2. 5.2.3.3 When prompted, save the file to the folder chosen or created in Step 5.2.3.1. The folder should now contain a file named CME2.zip. 5.2.3.4 Extract the contents of the zip file to the same location. The folder should now contain the files CME2.zip and Setup.exe. Copley Controls Corp. 87 Mode Selection and General Setup 5.2.3.5 Stepnet Panel Amplifier User Guide If desired, delete CME2.zip to save disk space. 5.2.4: Installing CME 2 Software 5.2.4.1 If installing from a CD, insert the CD (Copley Controls part number CME2). Normally, inserting the CD causes the installation script to launch, and a CME 2 Installation screen appears. If so, skip to Step 5.2.4.3. 5.2.4.2 If the software installation file was downloaded from the Copley Controls website, navigate to the folder chosen or created in Step 5.2.3.1, and then double-click on Setup.exe OR if you inserted the CD and the CME 2 Installation screen did not appear, navigate to the root directory of the installation CD and then double-click on Setup.exe. 5.2.4.3 Respond to the prompts on the CME 2 Installation screens to complete the installation. We recommend accepting all default installation values. 88 Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup 5.2.5: Serial Port Setup One or more serial ports on a PC can be used to connect amplifiers. Use the following instructions to add (enable) ports for amplifiers, to choose baud rates for those ports, and to remove (disable) ports for amplifiers. 5.2.5.1 Start CME 2 by double-clicking the CME 2 shortcut icon on the Windows desktop: If a serial or CAN port has not been selected, the Communications Wizard Select device screen appears. 5.2.5.2 If the CME 2 Main screen appears instead of Select Devices, choose Tools Communications Wizard. 5.2.5.3 Choose Serial Ports and click Next to open the Communications Wizard Select Ports screen. 5.2.5.4 From the Available Devices list on the Select Devices screen, choose the serial ports that will be used to connect to amplifiers. 1 To allow connection of an amplifier through a port, highlight the port name and click Add (or click Add All to enable all available ports). 2 To remove a port from the Selected Devices list, highlight the port name and click Remove. Copley Controls Corp. 89 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.2.5.5 Click Next to save the choices and open the Communications Wizard Configure Serial Ports screen. 5.2.5.6 Configure the selected ports. 1 Highlight a port in the Selected Devices list. 5.2.5.7 90 2 Choose a Baud Rate for that port. 3 Repeat for each selected port. Click Finish to save the choices. Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup 5.3: Prerequisites 5.3.1: Hardware and Equipment 5.3.1.1 Verify that all power is OFF. 5.3.1.2 Verify wiring to all amplifier connectors 5.3.1.3 Secure the motor. Make sure motor is securely fastened. 1 2 5.3.1.4 Make sure that no load is connected to the motor. STP: Apply Aux voltage if available. If the Aux supply is not wired, verify that the amplifier enable input (IN1) is in the disabled state and then apply HV power. The factory default setting for the enable input is open or pulled high for disable. STX: Apply 24 V only. ! DANGER Copley Controls Corp. Risk of unexpected or uncontrolled motion. CME 2 can be used while the amplifier is under other control sources such as CANopen and DeviceNet. However, some changes made with CME 2 could cause unexpected or uncontrolled motion. Failure to heed this warning can cause equipment damage, injury, or death. 91 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.3.2: Starting CME 2 and Choosing an Amplifier NOTE: Digital input 1 (IN1) must be configured as a hardware disable. It may be used to immediately disable the amplifier. To software disable the amplifier at any time while running CME 2, press function key F12. 5.3.2.1 Verify CME 2 installation and serial port configuration. Start CME 2 by double-clicking the CME 2 shortcut icon on the Windows desktop. If there are multiple ports, the Copley Neighborhood root will be selected: 5.3.2.2 Select the desired amplifier to open the CME 2 Main screen (varies with model and configuration): If basic setup settings have not been chosen, the Basic Setup screen opens. 92 Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup 5.4: Basic Setup 5.4.1: Basic Setup Screen 5.4.1.1 5.4.1.2 To load a .ccx file that was prepared for the amplifier/motor combination, see Quick Copy Setup Procedure (p. 156). Click the Basic Setup button to display the Basic Setup screen. 5.4.1.3 Click Change Settings to start the Basic Setup wizard. Use Back Next to navigate screens. Screen details vary depending on amplifier model and mode selection. 5.4.1.4 Select the Motor Type (Rotary or Linear). 5.4.1.5 View or change the Feedback settings described below: Setting Options Motor Encoder Primary Incremental or none. Encoder is required for servo mode operation. In stepper mode operation, it can provide position maintenance information. Run in Servo Mode When checked, amplifier runs in closed loop servo mode. See Stepper and Servo Modes (p. 10). Enable Encoder Correction When checked, amplifier runs in stepper mode and uses a programmable proportional gain to correct following errors. See Encoder Correction, p. 128. Copley Controls Corp. 93 Mode Selection and General Setup 5.4.1.6 Stepnet Panel Amplifier User Guide View or change the Operating Mode settings described below: Setting Options Operating Mode Stepper mode: Position. See Stepper Mode Operation (p. 16). Command Source PWM Command (current and velocity mode only): Digital pulse-width modulated signal provides command input. See Input Command Types (p. 25 ). Servo mode: Current, Velocity, Position. (See Servo Mode Operation (p. 18). Function Generator (current and velocity mode only): Internal function generator provides command input. Software Programmed: The amplifier is controlled by software commands from either the Copley Virtual Machine (CVM) or an external source. See Copley Indexer Program User’s Guide or the Copley ASCII Interface Programmer’s Guide. Digital Input (position mode only): Command input is provided via the Input Source selected from the choices described below. See Digital Position Inputs (p. 27). CAN: (position mode only): Command input is provided over the CANopen network. See Communication (p. 30) and the CANopen Programmer’s Guide. Camming (position mode only): Amplifier runs in Camming Mode. See Copley Camming User Guide. 5.4.1.7 94 Click Finish to close the Basic Setup screen. Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup 5.5: Motor Setup Motor, Feedback, and Brake settings can be loaded from a file or entered manually into the fields. Choose the appropriate method and perform the steps described: • • Load Motor/Feedback/Brake Data File (p. 95) Enter Motor/Feedback/Brake Settings Manually (p. 96) 5.5.1: Load Motor/Feedback/Brake Data File 5.5.1.1 5.5.1.2 To download motor data files from the website: 1 In an internet browser, navigate to http://www.copleycontrols.com/Motion/Downloads/motorData.html 2 Click the appropriate motor name. When prompted, save the file to the MotorData folder in the CME 2 installation folder. (The default installation folder is C:\Program Files\Copley Motion\CME 2\MotorData.) 3 Extract the contents of the zip file to the same location. 4 The folder should now contain the new motor data file (with a .ccm filename extension). 5 If desired, delete the .zip file to save disk space. To load motor data from a motor data file: Click Motor/Feedback to open the Motor/Feedback screen. 1 2 On the Motor/Feedback screen, click Restore Motor Data from Disk ( When prompted, navigate to the folder containing the file, then click on the file name, and then click Open. 3 Verify motor data files against manufacturer’s specifications. 4 Proceed to The Calculate Function (p. 99). Copley Controls Corp. ). 95 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.5.2: Enter Motor/Feedback/Brake Settings Manually 5.5.2.1 Click Motor/Feedback to open the Motor/Feedback screen. A Motor/Feedback screen representing a typical rotary motor is shown below. Parameters vary with amplifier model. 5.5.2.2 Click the Motor tab to view or change Rotary Motor Setup Parameters (p. 97) or Linear Motor Setup Parameters (p. 97). 5.5.2.3 5.5.2.4 5.5.2.5 5.5.2.6 5.5.2.7 96 Click the Feedback tab. For rotary motors, enter the number of Encoder Lines. For linear motors, enter the Encoder Resolution value and select the units for that value (mm, nm, or um). (STX only) Verify the Enable Encoder Loss Detection setting. See STX Encoder Loss Detection (p. 38). Click the Brake/Stop tab to view or change Brake/Stop Parameters (p. 98). Read the Brake/Stop Notes (p. 98) for important related information. Use The Calculate Function (p. 99) to calculate initial gains and limits. On the Main screen, click Save to Flash to avoid losing the changes. Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup 5.5.3: Rotary Motor Setup Parameters View or change the settings described below. Options vary with amplifier model. Metric units are shown here. Setting Description Manufacturer Motor manufacturer’s name. Saved for reference in the motor data file. Model Number Motor model number. Saved for reference in the motor data file. Units Selects whether the parameters entered in this screen are in Metric or English units. Motor Inertia The rotor inertia of the motor. Used in servo mode for calculating initial velocity loop tuning 2 2 2. values. Min: 0.00001 kg-cm . Max: 1,000 kg-cm . Default: 0.00001 kg-cm Resistance Motor resistance line-to-line. Used for calculating the initial current loop tuning values. Min: 0.01 . Max: 327 . Default: 0.01 . Inductance Motor inductance line-to-line. Used for calculating the initial current loop tuning values. For inductance range, see Power Output (p. 45). Rated Torque Motor’s rated operating torque. Min: .001 N m. Max: 1000 N m. Rated Current Motor’s rated continuous current. Min: 0.001 A. Max: 1000 A. Basic Step Angle Fundamental stepper motor step, in degrees. Min: 0.225. Max: 22.5. Default 1.8. µStep/Rev (stepper mode only) Number of microsteps per revolution of the motor. Min: 4. Max: 100,000,000. Default 4000. Note: When using encoder feedback, it is desirable to set this value equal to the number of encoder counts per rev. 5.5.4: Linear Motor Setup Parameters View or change the settings described below. Options vary with amplifier model. Metric units are shown here. Setting Description Manufacturer Motor manufacturer’s name. Saved for reference in the motor data file. Model Number Motor model number. Saved for reference in the motor data file. Units Selects whether the parameters entered in this screen are in Metric or English units. Motor Mass The mass of the moving component of the motor. Used in servo mode for calculating initial velocity loop tuning values. Min: .0001 Kg. Max: 100,000 Kg. Default: .0001 Kg. Resistance Motor resistance line to line. Used for calculating the initial current loop tuning values. Min: 0.01. Max: 327 . Default: 0.01 . Inductance Motor inductance line to line. Used for calculating the initial current loop tuning values. For inductance range, see Power Output (p. 45). Rated Force Motor’s rated operating force. Min .001 N. Max 1000 N. Rated Current Motor’s rated continuous current. Min: 0.01 A. Max 1000 A. Full Step Fundamental stepper motor step distance. Min: 0.0001mm. Max: 5000 mm. µStep/Full Step (stepper mode only) Number of microsteps per full step. Min: 1. Max: 25,000,000. Copley Controls Corp. 97 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.5.5: Brake/Stop Parameters Enter the following parameters as appropriate. Parameter Description Brake/Stop Delay Time Range of accepted values: 0 to 10,000 mSec. Brake Activation Velocity Range of accepted values: motor-dependent. PWM Delay Brake/Stop Response Time Range of accepted values: 0 to 10,000 mSec. Brake/Stop Notes Many control systems employ a brake to hold the axis when the amplifier is disabled. On brakeequipped systems, disabling the amplifier by a hardware or software command starts the following sequence of events. • • • The motor begins to decelerate (at Abort Deceleration rate in position mode or Fast Stop Ramp rate in velocity mode). At the same time, the Brake/Stop Delay Time count begins. This allows the amplifier to slow the motor before applying the brake. When the motor slows to Brake/Stop Activation Velocity OR the Brake/Stop Delay Time expires, the brake output activates and PWM Delay Brake/Stop Response Time count begins. When response time has passed, the amplifier’s output stages are disabled. This delay ensures the brake has time to lock in before disabling the power section. This sequence is not available in the current mode of operation. Instead, in current mode, the amplifier output turns off and the brake output activates immediately when the disable command is received. 98 Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup 5.5.6: The Calculate Function The Calculate function uses the motor and encoder values entered to calculate initial loop gains and limits. These can be modified later to fine-tune the amplifier. 5.5.6.1 Click Calculate ( ) to calculate and display the settings. Note that in servo mode, Peak Current and Continuous Current replace the stepper mode Boost Current and Run Current settings. 5.5.6.2 Verify the boost (peak) current limit and Run (Continuous) Current limit. If one or more of these values seems inappropriate, click Cancel and check: Rated Torque (or Force) and Rated Current. Correct them if needed. See Rotary Motor Setup Parameters (p. 97) or Linear Motor Setup Parameters (p. 97). If the Motor/Feedback values were correct but the peak current limit, continuous current limit, or velocity loop velocity limit values are not optimal for the application, change these limits during the tuning process. 5.5.6.3 Load the values into amplifier RAM by clicking OK. NOTE: If the motor wiring configuration in the motor file does not match the configuration currently stored in the amplifier, CME prompts for verification on which configuration to use. Select the file configuration by clicking Yes. The configuration will be tested during auto phasing. 5.5.6.4 On the Main screen, click Save to Flash to avoid losing the changes. Copley Controls Corp. 99 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.6: Amplifier Configuration 5.6.1: Digital Inputs 5.6.1.1 Click Input/Output on the Main screen to open the Input/Output screen. A typical Input/Output screen is shown below. (Features vary with model and configuration.) Red: inhibited motion or active input, depending on input function. Grey: motion not inhibited. None: not configured. Lo/Hi: Indicates state of input. Hold position setting 100 Indicates input is used as a CAN address bit. Copley Controls Stepnet Panel Amplifier User Guide 5.6.1.2 Mode Selection and General Setup Change or verify the following settings: Setting Description Pull up +5 V Pulls up the group of inputs up to internal +5 V. Pull down Pulls the group of inputs down to internal signal ground. IN1-IN12 Select the function for the input. See Digital Input Functions (p. 102) for input function descriptions. Debounce Time Sets the input debounce time (how long an input must remain stable at a new state before the amplifier recognizes the state). Increase to prevent undesired multiple triggering caused by switch bounce. Debounce time is ignored for digital command inputs such as PWM. Range: 0 to 10,000 mSec. See Debounce Time (p. 42). *Hold position when limit switch is active Available in position mode when one or more inputs are configured as a limit switch (NEG Limit-HI Inhibits, NEG Limit-LO Inhibits, POS Limit-HI Inhibits, or POS Limit-LO Inhibits). The Hold position… option prevents any motion while a limit switch is active. ! WARNING: Limit switches may be disabled. If the amplifier is switched back to current or velocity mode with Hold position when limit switch is active set, the limit switches will no longer function. Failure to heed this warning can cause equipment damage. WARNING The Restore Defaults button restores all inputs and outputs to factory defaults. The Close button closes the screen. Copley Controls Corp. 101 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.6.2: Digital Input Functions Input Function Description AMP EnableLO Enables with clear faults A low input will enable the amplifier. AMP EnableHI Enables with clear faults A high input will enable the amplifier. AMP EnableLO Enables with reset A low input will enable the amplifier. AMP EnableHI Enables with reset A high input will enable the amplifier. AMP EnableLO Enables A low input will enable the amplifier. AMP EnableHI Enables A high input will enable the amplifier. Not Configured No function assigned to the input. NEG Limit-HI Inhibits A high input will inhibit motion in negative direction. NEG Limit-LO Inhibits A low input will inhibit motion in negative direction. POS Limit-HI Inhibits A high input will inhibit motion in positive direction. POS Limit-LO Inhibits A low input will inhibit motion in positive direction. Reset on LO-HI Transition A low to high transition of the input will reset the amplifier. Reset on HI-LO Transition A high to low transition of the input will reset the amplifier. Motor Temp HI Disables A high input will generate a Motor Over Temperature fault. Motor Temp LO Disables A low input will generate a Motor Over Temperature fault. Home Switch Active HI A high input indicates the home switch is activated. Home Switch Active LO A low input indicates the home switch is activated. Motion Abort Active HI A high input stops motion but amplifier remains enabled. Motion Abort Active LO A low input stops motion but amplifier remains enabled. Hi Res Analog Divide Active HI A high input causes the firmware to divide the level of the analog input signal by 8. Hi Res Analog Divide Active LO A low input causes the firmware to divide the level of the analog input signal by 8. High Speed Position Capture on LO-HI Transition Position will be captured on the low to high transition of the input. High Speed Position Capture on HI-LO Transition Position will be captured on the high to low transition of the input. PWM Sync Input PWM synchronization input. Any transition will clear latched faults and outputs. Any transition will clear latched faults and outputs. A low to high transition will reset the amplifier. A high to low transition will reset the amplifier. 5.6.3: Standard Input Function Assignments Enable Input: On the Stepnet amplifier, IN1 is dedicated to the enable function. Other inputs can be programmed as additional enables. If there is more than one input programmed as an enable then all the inputs must be in the enabled state before the amplifier PWM output stage will be enabled. Motor Over Temperature: On the STX amplifier, IN12 is located on the motor feedback connector and is intended to be used for Motor Over Temperature. Other: Other inputs may have predefined functions depending on mode of operation. 102 Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup 5.6.4: Standard Digital Outputs 5.6.4.1 Click the Digital Outputs tab of the Input/Output screen. A typical Digital Outputs screen is shown below. (Features may vary with amplifier model and configuration.) Hi/Lo state of output Grey light: Output is not active Red light: Output is active 5.6.4.2 Choose any of these functions for any output. OUT4 is recommended for brake function. Output Function Description For More Information Not Configured No function assigned. Output remains high. Fault Active High Output goes high when one or more faults are detected. Fault-Active Low Output goes low when one or more faults are detected. Brake-Active High Output goes high to activate the brake. Brake-Active Low Output goes low to activate the brake. PWM Sync Output (OUT1 only) The PWM synchronization output. Custom Event See Custom Digital Output Settings: Custom Event (p. 104). Custom Trajectory Status See Custom Digital Output Settings: Custom Trajectory Status (p. 106). Custom Position Triggered Output See Custom Digital Output Settings: Position Triggered Output (p. 107). Program Control Active High Output state controlled by CVM or external program. Program Control Active Low Output state controlled by CVM or external program Copley Controls Corp. Faults (p. 37). Brake Operation (p. 34). 103 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.6.5: Custom Digital Output Settings: Custom Event Any of the amplifier’s digital outputs can be programmed to respond to a combination of events including faults, warnings, and status indications. The output goes active when one or more of the selected events take place. 5.6.5.1 5.6.5.2 Choose Custom Event for an output and then click Configure Custom to open the Event Configuration screen. Select one or more of the faults described in Fault Descriptions (p. 38) or any of the following warnings or status conditions described below. Note that multiple functions are OR’ed together, so any event activates the output. Custom Events: Warnings Warning Description The current output is being limited by the I T algorithm or a latched current fault 2 has occurred. See I T Time Limit Algorithm (p. 167). Voltage Limited The current loop is commanding full bus voltage in an attempt to control current. Commonly occurs when motor is running as fast as available bus voltage allows. Positive Limit Switch Negative Limit Switch Positive Software Limit Negative Software Limit Following Warning Axis has contacted positive limit switch. Axis has contacted negative limit switch. Velocity Limit Reached Acceleration Limit reached Velocity Outside of Tracking Window Position Outside of Tracking Window Continued… 104 2 Current Limited Actual position has exceeded the positive software limit setting. See Home Function (p. 164). Actual position has exceeded the negative software limit setting. See Home Function (p. 164). Following error has reached programmed warning limit. See Following Error Fault Details (p. 40). Velocity command (from analog input, PWM input, or position loop) has exceeded the velocity limit that was set as described in Servo Velocity Loop Limits (p. 21). In velocity mode, motor has reached an acceleration or deceleration limit that was set as described in Servo Velocity Loop Limits (p. 21). Difference between target and actual velocity has exceeded the window. See Tracking Window Details (p. 41). The following error has exceeded the programmed value. See Tracking Window Details (p. 41). Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup …Continued: Custom Events: Status Status Description Amplifier Disabled by Hardware Amplifier enable input(s) is not active. Amplifier Disabled by Software Amplifier is disabled by a software command. Attempting to Stop Motor The amplifier, while in velocity or position mode, has been disabled. In velocity mode, amplifier is using the Fast Stop Ramp described in Servo Velocity Loop Limits (p. 21). In position mode, the amplifier is using the Abort Deceleration rate described in Trajectory Limits (p. 23). The output remains active until the amplifier is re-enabled. Motor Brake Activated Motor brake activated. See Brake Operation (p. 34) for more information. PWM Outputs Disabled The amplifier’s PWM outputs are disabled. Home Switch is Active Axis has contacted the home limit switch. Not Settled The motor is moving, or it has not yet settled after a move. The amplifier is settled when it comes within the position tracking window and stays there for the tracking time at the end of a move. Once settled, it remains settled until a new move is started. 5.6.5.3 Choose Output Active High to have the output go high when active or Output Active Low to have the output go low when active. 5.6.5.4 To optionally latch the selected events, set Latch Output. For more information on latching, see Non-Latched and Latched Custom Outputs (p. 108). ! DANGER Latching an output does not eliminate the risk of unexpected motion with non-latched faults. Associating a fault with a latched, custom-configured output does not latch the fault itself. After the cause of a non-latched fault is corrected, the amplifier reenables without operator intervention. In this case, motion may re-start unexpectedly. Failure to heed this warning can cause equipment damage, injury, or death. 5.6.5.5 Click OK to save changes to volatile memory and close the Custom Output Configuration screen. Copley Controls Corp. 105 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.6.6: Custom Digital Output Settings: Custom Trajectory Status Any of the amplifier’s digital outputs can be programmed to respond to a combination of amplifier trajectory status conditions. The output goes active when one or more of the conditions is met. 5.6.6.1 5.6.6.2 Choose Custom Trajectory Status for an output and then click Configure Custom to open the Trajectory Status Configuration screen. Select one or more trajectory status conditions described below. Multiple functions are OR’ed together, so any status match activates the output. Trajectory Status Functions Status Description Homing Error Activate output if an error occurred in the last homing attempt. Referenced (Homed) Activate output if the most recent homing attempt was successful. Homing in Progress Activate output when a homing move is in progress. Move Aborted Activate output if move is aborted. Trajectory Generator Running Activate output while trajectory generator is generating a move. Camming Buffer Error A camming buffer error has occurred. 5.6.6.3 Choose Output Active High to have the output go high when active or Output Active Low to have the output go low when active. 5.6.6.4 Click OK to save changes to volatile memory and close the screen. 106 Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup 5.6.7: Custom Digital Output Settings: Position Triggered Output Any of the amplifier’s digital outputs can be programmed to respond in certain ways to the position of the controlled axis. The output goes active when the axis position meets the specified criteria. 5.6.7.1 5.6.7.2 Choose Custom Position Triggered Output for an output and then click Configure Custom to open the In Position Configuration screen. 5.6.7.3 Select one of the configurations described below and enter appropriate values for the parameters. Configuration Description and Parameters In Position Window Activates the output while the axis is in the window between the programmed Upper and Lower positions. Trigger at Position Activates the output for the programmed Time when the axis travels through the programmed Position. Trigger Positive Motion Activates the output for the programmed Time when the axis travels in the positive direction through the programmed Position. Trigger Negative Motion Activates the output for the programmed Time when the axis travels in the negative direction through the programmed Position. 5.6.7.4 Choose Output Active High to have the output go high when active or Output Active Low to have the output go low when active. 5.6.7.5 Choose Use Actual Position (with encoder only) or Use Limited Position. 5.6.7.6 Click OK to save changes to volatile memory and close the Custom Output Configuration screen. 5.6.8: Save Input/Output Changes 5.6.8.1 5.6.8.2 On the Input/Output screen, click Close. On the Main screen, click Save to Flash. Copley Controls Corp. 107 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.6.9: Non-Latched and Latched Custom Outputs Like an amplifier fault, a custom-configured output can be non-latched or latched. If a non-latched, custom-configured digital output goes active, it goes inactive as soon as the last of the selected events is cleared. If a latched output goes active, it remains active until at least one of the following actions has been taken: • • power-cycle the amplifier cycle (disable and then enable) an enable input that is configured as Enables with Clear Faults or Enables with Reset • • access the CME 2 Control Panel and press Clear Faults or Reset clear faults over the CANopen network ! DANGER Latching an output does not eliminate the risk of unexpected motion with nonlatched faults. Associating a fault with a latched, custom-configured output does not latch the fault itself. After the cause of a non-latched fault is corrected, the amplifier re-enables without operator intervention. In this case, motion may re-start unexpectedly. For more information, see Clearing Non-Latched Faults (p. 37). Failure to heed this warning can cause equipment damage, injury, or death. Custom Event Output Faults An output configured for Custom Event can be programmed to go active in response to events, including any of the amplifier faults described in Fault Descriptions (p. 38). Example: Custom Output Fault Handling vs. Overall Fault Handling A fault on an output configured for Custom Event is separate from a fault on the amplifier. For instance, suppose: • OUT3 has a Custom Event configuration. Only the Under Voltage fault condition is selected, and the output is latched. • Under Voltage is not latched on the Configure Faults screen. An under voltage condition occurs, and the amplifier goes into fault condition, output stages are disabled, and faults are reported. At the same time, OUT3 goes active. The under voltage condition is corrected, and: • • 108 The amplifier fault is cleared. Output stages are enabled. OUT3 remains active. Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup 5.6.10: Fault Latching Click Configure Faults to open the Fault Configuration screen. 5.6.10.1 Note that with no encoder, the Following error fault is not displayed as a choice. 5.6.10.2 To make a fault condition latching, click to put a check mark next to the fault description. Risk of unexpected motion with non-latched faults. ! DANGER After the cause of a non-latched fault is corrected, the amplifier re-enables the PWM output stage without operator intervention. In this case, motion may re-start unexpectedly. Configure faults as latched unless a specific situation calls for nonlatched behavior. When using non-latched faults, be sure to safeguard against unexpected motion. Failure to heed this warning can cause equipment damage, injury, or death. For more information on faults, see Faults (p. 37). 5.6.10.3 To restore factory defaults if needed, click Restore Defaults. 5.6.10.4 Click OK to save fault configuration settings to amplifier RAM and close the Fault Configuration screen OR click Cancel to restore to previous values and close the screen. 5.6.10.5 On the Main screen, click Save to Flash. Copley Controls Corp. 109 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.7: Command Input Choose the appropriate step for the input format. Input Format Step Digital Position Digital Position Input (p. 111) CAN CAN Interface (p. 112) PWM (servo mode only) PWM Input (p. 113) Analog Analog Command Input (STX Servo Mode Only) (p. 114) To run the amplifier with Command Input set to Software Programmed or Function Generator, see the CME 2 User Guide. To run the amplifier with Command Input set to Camming, see the Copley Camming User’s Guide. 110 Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup 5.7.1: Digital Position Input For more information, see Digital Position Inputs (p. 27). 5.7.1.1 Click Digital Position Inputs to open the Digital Position Input screen, Configuration tab. 5.7.1.2 Set the options described below: Option Description Control Input Pulse and Direction: One input takes a series of pulses as motion step commands, and another input takes a high or low signal as a direction command. Pulse Up / Pulse Down: One input takes each pulse as a positive step command, and another takes each pulse as a negative step command. Quadrature: A/B quadrature commands from a master encoder (via two inputs) provide velocity and direction commands. Increment position on Rising Edge: Increment position on the rising edge of the input pulse. Stepping Resolution Input Pulses: Number of Input Pulses required to produce output counts. Range: 1 to 32,767. Default: 1. Falling Edge: Increment position on the falling edge of the input pulse. Output Counts: Number of Output Counts per given number of input pulses. Range: 1 to 32,767. Default: 1. Invert Command 5.7.1.3 5.7.1.4 5.7.1.5 When selected, inverts commanded direction. Click Close. On the Main screen, click Save to Flash. Proceed to Stepper Mode Phase and Tune (p. 115). Copley Controls Corp. 111 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.7.2: CAN Interface For more information on CAN see CAN Addressing (p. 32). For information on DeviceNet, see the Copley DeviceNet Programmer’s Guide. 5.7.2.1 Verify that the CAN bus is properly wired and terminated according to the instructions in Stepnet Panel (STP) CAN Bus (J5 and J6) (p. 65). 1. J6 "CAN" CANopen cable 2. J6 "CAN" Termination plug 5.7.2.2 Click CAN Configuration to open the CAN Configuration screen. (If CAN is not the Position Loop Input, choose Amplifier Network Configuration instead.) Here is a typical CAN Configuration screen. (Features may vary based on amplifier model and configuration.) 5.7.2.3 Choose a Bit Rate and choose any combination of address sources (Switch, Inputs, and Programmed Value). The address is the sum of the values from these sources. 5.7.2.4 For each source selected, perform the additional steps described below. Source Additional Steps Use Switch Verify the S1 switch setting. (Assigns values for Bit 0 – Bit 3 of CAN address.) Use Inputs Enter the Number of inputs. Choose the input that will represent each CAN address bit. Use Programmed Enter the Programmed value. Value 5.7.2.5 Click Save & Reset to save changes to amplifier flash, close the screen, and reset the amplifier. Click Save & Close to save changes to amplifier flash without resetting. NOTE: CAN address and bit rate changes take effect only after power-up or reset. 5.7.2.6 Proceed to Stepper Mode Phase and Tune (p. 115) or Servo Mode Phase and Tune (p. 131) as appropriate. 112 Copley Controls Stepnet Panel Amplifier User Guide Mode Selection and General Setup 5.7.3: PWM Input (Servo Mode Only) For more information, see PWM Input (Servo Mode Only) (p. 29). Click PWM Command to open the PWM Command screen. 5.7.3.1 5.7.3.2 Set the input options described below. Option Description Scaling Current mode: output current at 100% duty cycle. Range: 0 to 10,000,000 A. Default: Peak Current value. Velocity mode: output velocity at 100% duty cycle. Range: 0 to 100,000 rpm (mm/sec). Default: Maximum Velocity value. PWM Input Type One wire 50% or two wire 100% with direction. Options Invert PWM input: Inverts the PWM logic. Allow 100% output: Overrides the 100% command safety measure. See Failsafe Protection from 0 or 100% Duty Cycle Commands (p. 29). Invert Sign Input: In 100% duty cycle mode, inverts the polarity of the directional input. 5.7.3.3 Click Close. 5.7.3.4 On the Main screen, click Save to Flash. 5.7.3.5 Proceed to Servo Mode Phase and Tune (p. 131). Copley Controls Corp. 113 Mode Selection and General Setup Stepnet Panel Amplifier User Guide 5.7.4: Analog Command Input (STX Servo Mode Only) For more information, see Analog Command Input (STX Servo Mode Only) (p. 25). Click Analog Command to open the Analog Command screen. 5.7.4.1 5.7.4.2 5.7.4.3 Set the input options described below. Option Description Scaling Current mode: output current produced by +10 Vdc of input. Range: 0 to 10,000,000 A. Default: Peak Current value. Velocity mode: output velocity produced by +10 Vdc of input. Range: 0 to 100,000 rpm (mm/sec). Default: Maximum Velocity value. Position mode: position change (counts or mm) produced by +10 Vdc of input. Range: 0 to 1,000,000,000 counts. Default: 1 Revolution of a rotary motor or 1 pole pair distance for a linear motor. For more information, see Scaling (p. 25). Dead Band Sets dead band. Range: -10,000 to 10,000 mV. Default: 0. For more information, see Dead Band (p. 25). Invert Command Inverts polarity of amplifier output with respect to input signal. Offset (Current and Velocity modes only.) Used to offset input voltage error in an open loop system. Not recommended for use when the amplifier is part of a closed loop system. Range: -10,000 to 10,000 mV. Default: 0. For more information, see Offset (p. 26). Analog Input Filter Programmable input filter. Disabled by default. See “Low-Pass and Bi-Quad Filters” in the CME 2 User’s Guide. Click Close. 5.7.4.4 On the Main screen, click Save to Flash. 5.7.4.5 Proceed to Servo Mode Phase and Tune (p. 131). . 114 Copley Controls CHAPTER 6: STEPPER MODE PHASE AND TUNE This chapter describes the general procedure for auto phasing and tuning an amplifier with a motor to operate in stepper mode. Step Page 6.1: Auto Phase (Stepper Mode) ............................................................................................................................................... 116 6.1.1: Auto Phase Warnings and Notes ........................................................................................................................... 116 6.1.2: Auto Phase Preliminary Steps ............................................................................................................................... 117 6.1.3: Auto Phase (Stepper Mode, No Encoder) .............................................................................................................. 117 6.1.4: Auto Phase Procedure (Stepper Mode with Encoder) ............................................................................................ 118 6.1.5: Trouble Shoot Motor Direction Setup ..................................................................................................................... 119 6.1.6: Trouble Shoot Motor Wiring Setup......................................................................................................................... 119 6.2: Position Limits (Stepper Mode with Encoder) ..................................................................................................................... 120 6.3: Current Loop....................................................................................................................................................................... 122 6.3.1: Current Loop Settings ............................................................................................................................................ 122 6.3.2: Manually Tune Current Loop.................................................................................................................................. 123 6.3.3: Optimize Hold and Run Current Ratings ................................................................................................................ 124 6.4: Profile Move Tests.............................................................................................................................................................. 125 6.4.2: Test S-Curve Profile .............................................................................................................................................. 127 6.5: Encoder Correction............................................................................................................................................................. 128 6.6: Completion Steps ............................................................................................................................................................... 129 6.6.1: Objective................................................................................................................................................................ 129 6.6.2: Steps ..................................................................................................................................................................... 129 Copley Controls Corp. 115 Stepper Mode Phase and Tune Stepnet Panel Amplifier User Guide 6.1: Auto Phase (Stepper Mode) 6.1.1: Auto Phase Warnings and Notes Warnings ! Motor Motion Applying high voltage power to the amplifier before auto phasing may result in motor motion. Be sure that motor motion will not cause injury. Failure to heed this warning can result in equipment damage, injury, or death. DANGER ! High Voltage Applying AC power to the STX amplifier applies high voltage to the amplifier-motor connections and cabling. Protect personnel against electrical shock. Failure to heed this warning can result in equipment damage, injury, or death. Danger Notes • Do not connect a load to the motor before performing Auto Phase procedure. • Always connect the motor using the same configuration. • Wire properly and consistently. • Connections are actually changed within the DSP, not at the motor terminals, and the results are saved to flash memory. The actual wire configuration should NEVER change. Phasing a stepper motor establishes positive direction for the motor and (if present) encoder. 116 Copley Controls Stepnet Panel Amplifier User Guide Stepper Mode Phase and Tune 6.1.2: Auto Phase Preliminary Steps 6.1.2.1 Verify that the Enable Input is not activated. 6.1.2.2 Apply power. 6.1.2.3 Choose the appropriate auto phase procedure for the configuration: Configuration Procedure Stepper mode, no encoder Auto Phase (Stepper Mode, No Encoder (p. 117)) Stepper mode with encoder Auto Phase Procedure (Stepper Mode with Encoder (p. 118)) 6.1.3: Auto Phase (Stepper Mode, No Encoder) 6.1.3.1 Click Auto Phase to open the Auto Phase Motor Direction Setup screen. 6.1.3.2 Activate the Enable Input. 6.1.3.3 Verify the Velocity, Acceleration, and Deceleration values. 6.1.3.4 Hold down Move POS to move the motor in the direction considered positive, and observe the direction of movement. If the motor does not move, see Trouble Shoot Motor Wiring Setup (p. 119). 6.1.3.5 If the motor did not move in the direction that you wish to program as the positive direction, click Invert Motor Output, and repeat 6.1.3.4. 6.1.3.6 Click OK to save the direction setting. 6.1.3.7 Proceed to Current Loop (p. 122). Copley Controls Corp. 117 Stepper Mode Phase and Tune Stepnet Panel Amplifier User Guide 6.1.4: Auto Phase Procedure (Stepper Mode with Encoder) Click Auto Phase to open the Auto Phase Motor Direction Setup screen. 6.1.4.1 Activate the Enable Input. 6.1.4.2 Move the motor at least three counts in the direction considered positive. 6.1.4.3 If the Motor Actual Position count does not change, see Trouble Shoot Motor Direction Setup (p. 119). 6.1.4.4 Click Next to open the Motor Wiring Setup screen. 6.1.4.5 Verify the Velocity setting. 6.1.4.6 Click Start to begin motor wiring setup. The software displays messages: Configuring Initial Settings, Microstepping, Test Complete, Motor Wiring has been configured. During microstepping, a current vector is applied to the motor windings and microstepped through an electrical cycle at a set rate, causing the motor to move. If you chose to Skip the motor direction setup step, Auto Phase will prompt for confirmation of correct motor direction. If the step fails see Trouble Shoot Motor Wiring Setup (p. 119). 6.1.4.7 118 Click Finish to close the screen and save values to amplifier flash. Copley Controls Stepnet Panel Amplifier User Guide Stepper Mode Phase and Tune 6.1.5: Trouble Shoot Motor Direction Setup If motor direction setup step failed: 6.1.5.1 If an encoder is used, check encoder power and signals. 6.1.5.2 Check shielding for proper grounding. 6.1.6: Trouble Shoot Motor Wiring Setup If motor wiring setup step failed: 6.1.6.1 Verify that amplifier is disabled. 6.1.6.2 Check for mechanical jamming. 6.1.6.3 Check for good connections to the motor power wires. 6.1.6.4 Disconnect motor power wires. 6.1.6.5 Measure for proper motor resistance. Copley Controls Corp. 119 Stepper Mode Phase and Tune Stepnet Panel Amplifier User Guide 6.2: Position Limits (Stepper Mode with Encoder) Click Position Limits to open the Position Limits screen. 6.2.1.1 6.2.1.2 120 Set the following Trajectory Values options as needed. Option Description Max Velocity Maximum trajectory velocity. Max value may depend upon the back EMF and the Max feedback count (servo mode) or maximum number of microsteps (stepper mode). Min:0. Default: 0.25 x motor velocity limit. Max Accel Maximum trajectory acceleration. Max value may depend upon the load inertia and boost current (stepper mode) or peak current (servo mode). Min:0 Max Decel Maximum trajectory deceleration. Max value may depend upon the load inertia and boost current (stepper mode) or peak current (servo mode). Min: 0 (disables limit). Abort Decel Deceleration rate used by the trajectory generator when motion is aborted. Min: 0 (disables limit). Clear Limits Sets Max Velocity, Max Accel, and Max Decel to zero, disabling the trajectory generator. Set Default Limits Restores Max Velocity, Max Accel, and Max Decel to calculated defaults. For More Information Servo Position Mode and Position Loop (p. 23). Brake Operation (p. 34). Copley Controls Stepnet Panel Amplifier User Guide 6.2.1.3 Open the Position Loop Values tab. 6.2.1.4 Set the following Position Loop Values options as needed. Option/Description Following Error Fault The level (in µSteps) at which the following error produces a fault. We recommend raising the fault level before tuning the loop. Warning The level (in µSteps) at which the following error produces a warning. Disable Fault Prevents following error from triggering a fault. Stepper Mode Phase and Tune For More Information Following Error Fault Details (p. 40). Tracking 6.2.1.5 6.2.1.6 Tracking Window Width of the tracking window in µSteps. Tracking Time Position must remain in the tracking window for this amount of time to be considered tracking. Tracking Window Details (p. 41). Click Close. On the Main screen, click Save to Flash to save the changes. Copley Controls Corp. 121 Stepper Mode Phase and Tune Stepnet Panel Amplifier User Guide 6.3: Current Loop Initial current loop proportional gain (Cp) and current loop integral gain (Ci) values were calculated during general amplifier setup. For an introductory overview of the control loops, see Stepper Mode Operation (p. 16). NOTE: For Copley digital amplifiers, current loop gain is independent of power supply voltage. 6.3.1: Current Loop Settings For more information, see Current Control in Stepper Mode (p. 17). Click I Loop to open the Current Loop screen: 6.3.1.1 6.3.1.2 122 Set the following options as needed. Options Description Boost Current Current used during acceleration and deceleration. Time at Boost Current. Maximum time at boost current. Run Current Current used during continuous velocity portion of moves. Hold Current Current used to hold motor at rest. Run to Hold Time The period of time, beginning when a move is completed, during which the output stays at Run Current level before switching to Hold Current level. Hold to Voltage Time The period of time, beginning when a move is completed, during which the output stays at Hold Current level before switching to the voltage mode in which the amplifier locks the duty cycle to prevent jitter. Setting to zero disables Voltage Mode. Cp Current loop proportional gain. Range 0 – 32,767. Ci Current loop integral gain. Range 0 – 32,767. Drive Output Maximize Smoothness: Amplifier uses circular vector limiting to produce smooth operation even into the voltage limits. Maximize Speed: Allows for slightly more of the bus voltage to be used when in the voltage limit. This may produce a small disturbance at top speed. Auto Tune See the CME 2 User Guide. Bandwidth Measure bandwidth using the Cp and Ci values now in the amplifier. Copley Controls Stepnet Panel Amplifier User Guide Stepper Mode Phase and Tune 6.3.2: Manually Tune Current Loop To tune the current loop, apply square-wave excitation to the current loop and adjust current loop proportional gain (Cp) and current loop integral gain (Ci) to obtain a desired waveform. NOTE: During tuning, observe any warnings that appear to the left of the trace. NOTE: For information on the alternate Auto Tune feature, see the CME 2 User Guide. Click the Scope Tool. 6.3.2.1 Choose Current from the Function Generator Apply To: list. 6.3.2.2 On the Settings tab, make sure Auto Setup is selected. Auto Setup automatically sets the following parameters: Function Generator Tab Function Square Wave. Amplitude 50 % of current loop Run Current setting. Frequency 100 Hz. Amplitude Offset 10 percent of current loop Run Current setting. Settings Tab Channel 1 Commanded Current (green). Channel 2 Actual current (white). Verify that the Amplitude value is not excessive for the motor. 6.3.2.3 6.3.2.4 Click Start. 6.3.2.5 1 2 On the Gains tab, adjust current loop proportional gain (Cp). Set current loop integral gain (Ci) to zero. Raise or lower Cp until desired step response is obtained. Typically, this means little or no overshoot with a 100 Hz square wave at 50 percent of Run Current. If the Cp value is too large, ringing may occur. If the Cp value is too low, bandwidth decreases. Make sure gain values don’t produce excessive ring. To change a value, highlight the value. Then enter value directly, use TIP: mouse and arrow controls, OR use Page Up/Page Down keys to move in increments of 10. Copley Controls Corp. 123 Stepper Mode Phase and Tune 6.3.2.6 Stepnet Panel Amplifier User Guide Adjust current loop integral gain (Ci) until desired settling time is obtained. Press Stop to stop the function generator. 6.3.2.7 On the Main screen, click Save to Flash to avoid losing the changes. 6.3.2.8 6.3.3: Optimize Hold and Run Current Ratings 6.3.3.1 Reduce Hold Current if possible, to reduce heat generation. 1 Test with load OR 2 6.3.3.2 124 Calculate: Hold Current requirement >= hold torque x (rated current/rated torque) Reduce Run Current if possible, to reduce heat generation. Copley Controls Stepnet Panel Amplifier User Guide Stepper Mode Phase and Tune 6.4: Profile Move Tests Test the system with various gains, limits, and load conditions. NOTE: During profile tests, observe any warnings that appear to the left of the trace. 6.4.1.1 Click the Scope Tool. 6.4.1.2 Select the Profile tab. 6.4.1.3 On the Settings tab, make sure Auto Setup is selected. Auto Setup automatically sets the following parameters: Profile Tab Move Relative Type Trap Distance ½ revolution (rotary) or 2 cm (linear) Reverse and repeat Not checked Settings Tab Channel 1 Profile velocity (green) Channel 2 Actual current (white) Channel 3 Commanded current (purple) Copley Controls Corp. 125 Stepper Mode Phase and Tune 6.4.1.4 Stepnet Panel Amplifier User Guide Set up a trapezoidal profile by setting the trajectory limits and distance. See table: Trajectory Limits Tab Maximum Velocity Maximum Acceleration Set values typical of those expected to be used in the application. Maximum Deceleration Profile Tab Distance Set the move distance to produce a complete trajectory profile. Be sure that this distance does not exceed mechanical limits of the system. Move Relative Type Trap NOTES: 1 The profile may not reach constant velocity during a short move. 2 At higher speeds, motor back EMF may limit Boost and Run currents. 6.4.1.5 Click Start. The Profile Generator executes the move. 6.4.1.6 Verify that the boost, run, and hold currents are appropriate for the move. 6.4.1.7 Try multiple sets of profiles representing typical moves that might be executed in the application. Starting with Set up a trapezoidal profile, repeat the process as needed. 126 Copley Controls Stepnet Panel Amplifier User Guide Stepper Mode Phase and Tune 6.4.2: Test S-Curve Profile NOTE: Skip this step unless the amplifier will perform CANopen S-Curve profile moves. Jerk is the rate of change of acceleration. S-Curve moves reduce jerk to provide a smooth profile. To tune the level of jerk, run an S-Curve profile and adjust velocity, acceleration, deceleration, and jerk levels until the desired profile is obtained. On the Profile tab, click the S-Curve button. 6.4.2.1 6.4.2.2 Set up an S Curve profile by adjust the following options. Set values that represent a typical move under normal operation. Trajectory Limits Tab Maximum Velocity Maximum speed of the profile. Maximum Acceleration/Deceleration Top acceleration/deceleration of the profile. Deceleration = acceleration. Maximum Jerk The jerk value set by Calculate procedure gives an S-Curve whose maximum slope = the trapezoidal profile slope. This value gives a maximum acceleration no greater than the initial acceleration. Small values produce less jerking but take longer to complete move. Large values produce more jerking and a more trapezoidal profile but complete the move faster. Profile Tab Distance Increase the move distance to produce a complete trajectory profile. Use an acceptable value the does not exceed mechanical limits of the system. Move Relative Type S-Curve 6.4.2.3 Verify that the boost, run, and hold currents are appropriate for the move. 6.4.2.4 Try multiple sets of profiles representing typical moves that might be executed in the application. Starting with Set up an S Curve profile, repeat the process as needed. Copley Controls Corp. 127 Stepper Mode Phase and Tune Stepnet Panel Amplifier User Guide 6.5: Encoder Correction Optionally set encoder correction options: 6.5.1.1 Make sure the Encoder Correction option has been set. See Basic Setup Screen, p. 93. 6.5.1.2 On the CME 2 Main screen, click Encoder Correction to open the Encoder Correction screen. 6.5.1.3 Set the following options: Options Description 128 ECp Gain used to correct following error. Max Step Rate Controls the maximum rate at which the axis is moved to provide encoder correction. Copley Controls Stepnet Panel Amplifier User Guide Stepper Mode Phase and Tune 6.6: Completion Steps 6.6.1: Objective Save the work and perform additional testing with load and under normal control source. 6.6.2: Steps 6.6.2.1 On the Main screen, click Save to Flash. 6.6.2.2 Remove power. 6.6.2.3 Attach load. 6.6.2.4 Reconnect power. 6.6.2.5 Re-test profiles. 6.6.2.6 On the Main screen, click Save to Flash 6.6.2.7 On the Main screen, click Save to Disk (for backup or duplication). 6.6.2.8 Click Control Panel and then click Reset OR Power-cycle the amplifier. 6.6.2.9 The amplifier stepper mode tuning procedure is complete. Copley Controls Corp. 129 Stepper Mode Phase and Tune Stepnet Panel Amplifier User Guide . 130 Copley Controls CHAPTER 7: SERVO MODE PHASE AND TUNE This chapter describes the general procedure for auto phasing and tuning an amplifier with a motor to operate in servo mode. Step Page 7.1: Auto Phase (Servo Mode)................................................................................................................................................... 132 7.1.1: Auto Phase Warnings and Notes ........................................................................................................................... 132 7.1.2: Auto Phase Preliminary Steps ............................................................................................................................... 132 7.1.3: Auto Phase Procedure........................................................................................................................................... 133 7.1.4: Trouble Shoot Motor Direction Setup ..................................................................................................................... 135 7.1.5: Trouble Shoot Motor Wiring Setup......................................................................................................................... 135 7.2: Current Loop....................................................................................................................................................................... 136 7.2.1: Current Loop Settings ............................................................................................................................................ 136 7.2.2: Manually Tune Current Loop.................................................................................................................................. 137 7.3: Velocity Loop...................................................................................................................................................................... 139 7.3.1: Velocity Loop Settings ........................................................................................................................................... 139 7.3.2: Manually Tune the Velocity Loop ........................................................................................................................... 140 7.4: Position Loop...................................................................................................................................................................... 141 7.4.1: Position Loop Settings ........................................................................................................................................... 141 7.4.2: Manually Tune the Position Loop ........................................................................................................................... 145 7.4.3: Test S-Curve Profile .............................................................................................................................................. 147 7.5: Completion Steps ............................................................................................................................................................... 148 7.5.1: Objective................................................................................................................................................................ 148 7.5.2: Steps ..................................................................................................................................................................... 148 Copley Controls Corp. 131 Servo Mode Phase and Tune Stepnet Panel Amplifier User Guide 7.1: Auto Phase (Servo Mode) 7.1.1: Auto Phase Warnings and Notes Warnings ! Motor Motion Applying high voltage power to the amplifier before auto phasing may result in motor motion. Be sure that motor motion will not cause injury. Failure to heed this warning can result in equipment damage, injury, or death. DANGER ! High Voltage Applying AC power to the STX amplifier applies high voltage to the amplifier-motor connections and cabling. Protect personnel against electrical shock. Failure to heed this warning can result in equipment damage, injury, or death. Danger Notes • Do not connect a load to the motor before performing Auto Phase procedure. • Always connect the motor using the same configuration. • Wire properly and consistently. • Connections are actually changed within the DSP, not at the motor terminals, and the results are saved to flash memory. The actual wire configuration should NEVER change. Phasing a stepper motor establishes positive direction for the motor and encoder. 7.1.2: Auto Phase Preliminary Steps 7.1.2.1 Verify that the Enable Input is not activated. 7.1.2.2 Apply power. 132 Copley Controls Stepnet Panel Amplifier User Guide Servo Mode Phase and Tune 7.1.3: Auto Phase Procedure Click Auto Phase to open the Auto Phase Motor Direction Setup screen. 7.1.3.1 Activate the Enable Input. 7.1.3.2 Move the motor in the direction to be considered positive OR if you cannot move the motor, click Skip (you will confirm motor direction later). NOTE: If an output is configured as a brake you can temporarily release the brake by holding down the Release Brake button. The brake will be reactivated when you release the button. 7.1.3.3 The Actual Position value on the screen should change. If it does not change, see Trouble Shoot Motor Direction Setup (p. 119). 7.1.3.4 Click Next to open the Motor Wiring Setup screen. 7.1.3.5 Click Start to begin the motor wiring setup. The software displays messages: Configuring Initial Settings, Microstepping, Test Complete, Motor Wiring has been configured. During microstepping, a current vector is applied to the motor windings and microstepped through an electrical cycle at a set rate, causing the motor to move. If you chose to Skip the motor direction setup step, Auto Phase will prompt for confirmation of correct motor direction. If the step fails see Trouble Shoot Motor Wiring Setup (p. 119). NOTE: If incorrect values were entered for inductance and resistance, the calculated Cp and Ci values may produce current loop oscillation, evidenced by an audible high frequency squeal during auto phasing. Copley Controls Corp. 133 Servo Mode Phase and Tune Stepnet Panel Amplifier User Guide 7.1.3.6 Click Next to open the Phase Count Test screen. 7.1.3.7 Click Start to begin the Phase Count Test. Observe status messages. See the prompt: 7.1.3.8 When you are ready to observe motion, click OK. See the prompt: 7.1.3.9 If motor did not turn 1 full turn, click No and verify that in the Motor/Feedback screen the following parameters have been set correctly: Number of Poles for rotary motors. Magnetic Pole Pair Length for linear motors Encoder Lines or Fundamental Lines for rotary encoders. Encoder Resolution for linear encoders. 134 Copley Controls Stepnet Panel Amplifier User Guide Servo Mode Phase and Tune 7.1.3.10 If motor turned 1 full turn, click Yes. 7.1.3.11 Click Next to open the Motor Phase Initialize screen. 7.1.3.12 Click Initialize Phase. The screen will display completion messages: Test Complete, Phasing has been initialized. 7.1.3.13 Click Finish to close the screen and save values to amplifier flash 7.1.3.14 If the Auto Phase algorithm does not produce desired results, try adjusting the Auto phase Current and Increment Rate values. 7.1.4: Trouble Shoot Motor Direction Setup If motor direction setup step failed: 7.1.4.1 If an encoder is used, check Encoder power and signals. 7.1.4.2 Check shielding for proper grounding. 7.1.5: Trouble Shoot Motor Wiring Setup If motor wiring setup step failed: 7.1.5.1 Verify that amplifier is disabled. 7.1.5.2 Check for mechanical jamming. 7.1.5.3 Check for good connections to the motor power wires. 7.1.5.4 Disconnect motor power wires. 7.1.5.5 Measure for proper motor resistance. Copley Controls Corp. 135 Servo Mode Phase and Tune Stepnet Panel Amplifier User Guide 7.2: Current Loop Initial current loop proportional gain (Cp) and current loop integral gain (Ci) values were calculated during general amplifier setup. For an introductory overview of the control loops, see Servo Modes and Control Loops (p. 19). NOTE: For Copley Controls digital amplifiers, the current loop gain is independent of the power supply voltage. 7.2.1: Current Loop Settings For more information, see Servo Current Mode and Current Loop (p. 19). Click I Loop to open the Current Loop screen: 7.2.1.1 7.2.1.2 Set the following options as needed. Options Description Peak Current Limit 2 Used to limit the peak phase current to the motor. Max value depends upon the amplifier model. Min value > continuous limit. 2 I T Time Limit Sets I T Time Limit in mSec. For more information, see I2T Time Limit Algorithm (p. 167 ). Continuous Current Limit Used to limit the Phase Current. Max Value is < Peak Current and depends upon the amplifier model. Min value: 0 Current Loop Offset Sets current loop offset. Leave it set to zero until after tuning. For more information, see Offset (p. 19). Cp Current loop proportional gain. Range 0 – 32,767. Ci Current loop integral gain. Range 0 – 32,767. Drive Output Maximize Smoothness: Amplifier uses circular vector limiting to produce smooth operation even into the voltage limits. Maximize Speed: Allows for slightly more of the bus voltage to be used when in the voltage limit. This may produce a small disturbance at top speed. 136 Auto Tune See the CME 2 User Guide.. Bandwidth Measure bandwidth using the Cp and Ci values now in the amplifier. Copley Controls Stepnet Panel Amplifier User Guide Servo Mode Phase and Tune 7.2.2: Manually Tune Current Loop To tune the current loop, apply square-wave excitation to the current loop and adjust current loop proportional gain (Cp) and current loop integral gain (Ci) to obtain a desired waveform. NOTE: During tuning, observe any warnings that appear to the left of the trace and take appropriate action. NOTE: For information on the alternate Auto Tune feature, see the CME 2 User Guide. Click the Scope Tool to open the Oscilloscope window. 7.2.2.1 Choose Current from the Function Generator Apply To: list. 7.2.2.2 On the Settings tab, make sure Auto Setup is selected. Auto Setup automatically sets the following parameters: Function Generator Tab Function Square Wave Amplitude 10 % of current loop Continuous Current Limit setting Frequency 100 Hz Settings Tab Channel 1 Commanded Current (green) Channel 2 Actual current (white) Verify that the Amplitude value is not excessive for the motor. 7.2.2.3 7.2.2.4 Click Start. 7.2.2.5 1 2 On the Gains tab, adjust current loop proportional gain (Cp). Set current loop integral gain (Ci) to zero. Raise or lower Cp until desired step response is obtained. Typically, this means little or no overshoot with a 100 Hz, low-current square wave. If the Cp value is too large, ringing may occur. If the Cp value is too low, bandwidth decreases. Make sure gain values don’t produce excessive ring. To change a value, highlight the value. Then enter value directly, use TIP: mouse and arrow controls, OR use Page Up/Page Down keys to move in increments of 10. Copley Controls Corp. 137 Servo Mode Phase and Tune 7.2.2.6 7.2.2.7 Stepnet Panel Amplifier User Guide Adjust current loop integral gain (Ci) until desired settling time is obtained. Press Stop to stop the function generator. 7.2.2.8 On the Main screen, click Save to Flash to avoid losing the changes. 7.2.2.9 If the amplifier is to be operated in current mode, skip the velocity and position loop setup procedures and go to Completion Steps (p. 148). 138 Copley Controls Stepnet Panel Amplifier User Guide Servo Mode Phase and Tune 7.3: Velocity Loop Initial velocity loop proportional gain (Vp) and velocity loop integral gain (Vi) values were calculated during general amplifier setup. 7.3.1: Velocity Loop Settings For more information, see Servo Velocity Mode and Velocity Loop (p. 21). Click V Loop. 7.3.1.1 Enter the following options as needed. Option Description Velocity Limit Top speed limit. Max value may depend upon the back EMF & the Encoder resolution. Min value: 0. Acceleration Limit Maximum acceleration rate. Max value may depend upon load, inertia, & peak current. Min value: 1. (Does not apply in position mode.) Deceleration Limit Maximum deceleration rate. Max value may depend upon load, inertia, & peak current. Min value: 1. (Does not apply in position mode.) Tracking Window Width of the tracking window in rpm (or mm/s for linear). Tracking Time Position must remain in the tracking window for this amount of time to be considered tracking. Vp Velocity loop proportional gain. Range: 0 to 32,767. Vi Velocity loop integral gain. Range: 0 to 32,767. Fast Stop Ramp Deceleration rate used by the velocity loop when the amplifier is hardware disabled. Range: 0 to 100,000,000. Default: velocity loop Decel. Limit value. For more information, see Servo Velocity Loop Limits (p. 21). Low Gains Shift Increases the resolution of the units used to express Vp and Vi, providing more precise tuning. For more information, see Servo Velocity Gains Shift (p. 22). High Gains Shift Decreases the resolution of the units used to express Vp and Vi, providing more precise tuning. For more information, see Servo Velocity Gains Shift (p. 22). Vi Drain (integral bleed) Vi drain modifies the effect of velocity loop integral gain. The higher the Vi Drain value, the faster the integral sum is lowered. Range: 0 to 32,000. Default: 0. Command Filter/ Output Filter For more information, see the CME 2 User Guide. Copley Controls Corp. 139 Servo Mode Phase and Tune Stepnet Panel Amplifier User Guide 7.3.2: Manually Tune the Velocity Loop To tune the velocity loop, apply square-wave excitation to the velocity loop and adjust velocity loop proportional gain (Vp) and velocity loop integral gain (Vi) to obtain a desired waveform. NOTE: During tuning, observe any warnings that appear to the left of the trace. Click the Scope Tool to open the Oscilloscope window. 7.3.2.1 Choose Velocity from the Function Generator Apply To: list. 7.3.2.2 On the Settings tab, make sure Auto Setup is selected. Auto Setup automatically sets the following parameters: Function Tab Function Square Wave Amplitude 10% velocity loop Vel. Limit setting. Frequency 5 Hz Settings Tab Channel 1 Limited velocity (green) Channel 2 Actual motor velocity (white) Verify that the Amplitude value is not excessive for the motor. 7.3.2.3 Click Start. 7.3.2.4 7.3.2.5 On the Gains tab, adjust velocity loop proportional gain (Vp). Set velocity loop integral gain (Vi) to zero. 1 2 7.3.2.6 7.3.2.7 7.3.2.8 7.3.2.9 140 Raise or lower velocity loop proportional gain (Vp) until desired step response is obtained. Typically, this means little or no overshoot on a 5 Hz small, slow-speed square wave. Adjust velocity loop integral gain (Vi) until desired settling time is obtained. Press Stop to stop the function generator. On the Main screen, click Save to Flash to avoid losing the changes. If the amplifier is to be operated in velocity mode, skip the position loop setup procedures and go to Completion Steps (p. 148). Copley Controls Stepnet Panel Amplifier User Guide Servo Mode Phase and Tune 7.4: Position Loop Initial position loop proportional gain (Pp), velocity feed forward (Vff), and acceleration feed forward (Aff) values were calculated during general amplifier setup. 7.4.1: Position Loop Settings For more information, see Servo Position Mode and Position Loop (p. 23). 7.4.1.1 Click P Loop to open the Position Loop screen. Copley Controls Corp. 141 Servo Mode Phase and Tune 7.4.1.2 142 Set the following Trajectory Values as needed: Option Description Max Velocity Maximum trajectory velocity. Max value may depend upon the back EMF and the Max feedback count (servo mode) or maximum number of microsteps (stepper mode). Min:0. Default: 0.25 x motor velocity limit. Max Accel Maximum trajectory acceleration. Max value may depend upon the load inertia and boost current (stepper mode) or peak current (servo mode). Min:0 Max Decel Maximum trajectory deceleration. Max value may depend upon the load inertia and boost current (stepper mode) or peak current (servo mode). Min: 0 (disables limit). Abort Decel Deceleration rate used by the trajectory generator when motion is aborted. Min: 0 (disables limit). Jerk The value of jerk set during the calculate procedure produces an S-Curve whose maximum slope is equal to the trapezoidal profile slope. This value will produce a maximum acceleration that is not more than the initial default value of acceleration. Small values will produce less jerking but will take longer to complete move. Large values will produce more jerking and a more trapezoidal profile but will complete the move faster. Clear Limits Sets Max Velocity, Max Accel, and Max Decel to zero, disabling the trajectory generator. Set Default Limits Restores Max Velocity, Max Accel, and Max Decel to calculated defaults. Stepnet Panel Amplifier User Guide For More Information Servo Position Mode and Position Loop (p. 23). Brake Operation (p. 34). Copley Controls Stepnet Panel Amplifier User Guide 7.4.1.3 Servo Mode Phase and Tune Open the Position Loop Values tab: Copley Controls Corp. 143 Servo Mode Phase and Tune 7.4.1.4 Set the following Position Loop Values as needed: Option Description Gains Aff Acceleration feed forward. Range: 0 to 32,767. Vff Velocity feed forward. Range: 0 to 32,767. 100% Vff = 16,384. Pp Position loop proportional gain. Range: 0 to 32,767. Gains Multiplier The output of the position loop is multiplied by this value before being passed to the velocity loop. Stepnet Panel Amplifier User Guide For More Information… Servo Position Loop Gains (p. 24). Following Error Fault The level (in encoder counts) at which the following error produces a fault. We recommend raising the fault level before tuning the loop. Warning The level (in encoder counts) at which the following error produces a warning. Disable Fault Prevents following error from triggering a fault. Following Error Fault Details (p. 40). Tracking Tracking Window Width of the tracking window in counts. Tracking Time Position must remain in the tracking window for this amount of time to be considered tracking. Tracking Window Details (p. 41). Position Wrap Opens the configuration controls for the Position Wrap feature. This feature causes the amplifier to “wrap back” the reported position value (set it back to zero) at a user-defined position, instead of continually increasing. By default, this feature is disabled. 144 CME 2 User Guide. Copley Controls Stepnet Panel Amplifier User Guide Servo Mode Phase and Tune 7.4.2: Manually Tune the Position Loop Minimize following error and oscillation by running profiles and adjusting position proportional gain (Pp), velocity feed forward (Vff), acceleration feed forward (Aff) and other settings. NOTE: During position loop tuning, observe any warnings that appear to the left of the trace. 7.4.2.1 Perform an auto setup test: Click the Scope Tool to open the Oscilloscope window. 1 Select the Profile tab. 2 3 On the Settings tab, make sure that Auto Setup is checked. Auto Setup automatically sets the following options: Profile Tab Move Relative Type Trap Distance ½ revolution (rotary) or 2 cm (linear) Reverse and repeat Not selected Settings Tab 4 5 Channel 1 Profile velocity (green) Channel 2 Following error (white) If the auto setup default profile distance is not appropriate, enter an appropriate short distance. Set up a trapezoidal profile by setting the trajectory limits and distance on the Trajectory Limits tab. See table: Trajectory Limits Tab Maximum Velocity Maximum Acceleration Set values typical of those expected to be used in the application. Maximum Deceleration Profile Tab Distance Set the move distance to produce a complete trajectory profile. Be sure that this distance does not exceed mechanical limits of the system. Move Relative Type Trap Copley Controls Corp. 145 Servo Mode Phase and Tune 6 Stepnet Panel Amplifier User Guide Click Start. The Profile Generator executes a short move. NOTES: 7.4.2.2 1 The profile may not reach constant velocity during a short move. 2 If following error occurs, open CME 2 Control Panel ( ) and click Clear Faults. Adjust position proportional gain (Pp) to minimize following error. Note that too much position loop proportional gain (Pp) might cause oscillation. 1 On the Gains tab, set velocity feed forward (Vff) and acceleration feed forward (Aff) to zero. 2 On the Profile tab, click Start. On the Gains tab, adjust position loop proportional gain (Pp) until best result is obtained. 3 Click Start after each adjustment to test the new value on a new profile move. NOTE: If a following error occurs, open the CME 2 Control Panel ( Faults. 7.4.2.3 7.4.2.4 ) and click Clear Adjust velocity feed forward (Vff): Velocity feed forward (Vff) reduces following error in the constant velocity portion of the profile. Often, a velocity feed forward (Vff) value of 16384 (100%) provides best results. 1 Click in the Vff field and adjust the value. 2 Click Start after each adjustment to test the new value on a new profile move. Adjust acceleration feed forward (Aff): Acceleration feed forward (Aff) reduces following error during profile acceleration and deceleration. 1 Click in the Aff field and adjust the value. 2 Click Start after each adjustment to test the new value on a new profile move. NOTE: If, after tuning the position loop, the motor makes a low frequency audible noise while enabled but not moving, the velocity loop gains (Vp and Vi) may be lowered to reduce the noise. If the gain values are set too low, the response to instantaneous rates of change might be reduced (i.e., slow correction to disturbances or transients). 7.4.2.5 146 Try multiple sets of profiles representing typical moves that might be executed in the application. Starting with Set up a trapezoidal profile, repeat the process as needed. Copley Controls Stepnet Panel Amplifier User Guide Servo Mode Phase and Tune 7.4.3: Test S-Curve Profile NOTE: Skip this step unless the amplifier will perform S-Curve profile moves. Jerk is the rate of change of acceleration. S-Curve moves reduce jerk to provide a smooth profile. To tune the level of jerk, run an S-Curve profile and adjust velocity, acceleration, deceleration, and jerk levels until the desired profile is obtained. On the Profile tab, click the S-Curve button. 7.4.3.1 7.4.3.2 Set up an S-curve profile by adjusting the following options. Set values that represent a typical move under normal operation. Trajectory Limits Tab Maximum Velocity Maximum speed of the profile. Maximum Acceleration Maximum acceleration/deceleration of the profile. The deceleration is set to be the same as acceleration. Maximum Jerk The value of jerk set during the calculate procedure produces an S-Curve whose maximum slope is equal to the trapezoidal profile slope. This value will produce a maximum acceleration that is not more than the initial default value of acceleration. Small values will produce less jerking but will take longer to complete move. Large values will produce more jerking and a more trapezoidal profile but will complete the move faster. Profile Tab Distance Increase the move distance to produce a complete trajectory profile. Use an acceptable value the does not exceed mechanical limits of the system. Move Relative Type S-Curve 7.4.3.3 Click Start. 7.4.3.4 Adjust values for desired results. 7.4.3.5 Try multiple sets of profiles representing typical moves that might be executed in the application. Starting with Set up an S-curve profile, repeat the process as needed. Copley Controls Corp. 147 Servo Mode Phase and Tune Stepnet Panel Amplifier User Guide 7.5: Completion Steps 7.5.1: Objective Save the work and perform additional testing with load and under normal control source. 7.5.2: Steps 7.5.2.1 On the Main screen, click Save to Flash. 7.5.2.2 Remove power. 7.5.2.3 Attach load. 7.5.2.4 Reconnect power. 7.5.2.5 Re-tune velocity and position loops if applicable. 7.5.2.6 On the Main screen, click Save to Flash. 7.5.2.7 On the Main screen, click Save to Disk (for backup or duplication). 7.5.2.8 Click Control Panel and then click Reset OR Power-cycle the amplifier. 7.5.2.9 The servo setup procedure is complete. 148 Copley Controls CHAPTER 8: USING CME 2 (STEPPER OR SERVO MODE) This chapter provides an overview of CME 2 software features. Contents are relevant to operation in both stepper and servo modes, and include: Title Page 8.1: CME 2 Overview................................................................................................................................................................. 150 8.1.1: Main Screen Overview........................................................................................................................................... 150 8.1.2: Tool Bar Overview ................................................................................................................................................. 150 8.1.3: Main Menu Overview ............................................................................................................................................. 151 8.1.4: Functional Diagram................................................................................................................................................ 152 8.1.5: CAN or DeviceNet Information and Status Bar ...................................................................................................... 153 8.1.6: Choosing an Amplifier from a List of Amplifiers...................................................................................................... 153 8.1.7: Renaming an Amplifier .......................................................................................................................................... 153 8.2: Manage Amplifier and Motor Data ...................................................................................................................................... 154 8.2.1: Memory.................................................................................................................................................................. 154 8.2.2: Disk Storage .......................................................................................................................................................... 154 8.2.3: Data Management Tools........................................................................................................................................ 155 8.2.4: Quick Copy Setup Procedure................................................................................................................................. 156 8.3: Downloading Firmware ....................................................................................................................................................... 157 8.3.1: Acquiring Firmware Updates from Web Site .......................................................................................................... 157 8.3.2: Downloading Firmware to Amplifier........................................................................................................................ 158 8.4: Control Panel...................................................................................................................................................................... 159 8.4.1: Control Panel Overview ......................................................................................................................................... 159 8.4.2: Status Indicators and Messages ............................................................................................................................ 159 8.4.3: Monitor Functions .................................................................................................................................................. 161 8.4.4: Control Functions................................................................................................................................................... 162 8.4.5: Jog Mode............................................................................................................................................................... 163 8.5: Home Function ................................................................................................................................................................... 164 8.5.1: Overview................................................................................................................................................................ 164 8.5.2: Homing Functions Settings .................................................................................................................................... 164 Copley Controls Corp. 149 Using CME 2 Stepnet Panel Amplifier User Guide 8.1: CME 2 Overview 8.1.1: Main Screen Overview The CME 2 features called out in the diagram below are described in the following sections. Main Menu Tool Bar Copley Neighborhood Tree CAN or DeviceNet Information Functional Diagram Status Bar 8.1.2: Tool Bar Overview Click on any of the tools in the toolbar to access the tools described below. Icon 150 Name Description For More Information Basic Setup Opens Basic Setup screen. Basic Setup (p. 93). Control Panel Opens Control Panel. Control Panel (p. 159). Auto Phase Opens Auto Phase tool. Auto Phase (p. 116) and Auto Phase (p. 132). Scope Opens Scope. CME 2 User Guide. Error Log Opens Error Log. CME 2 User Guide. Amplifier Properties Displays basic amplifier properties. Save amplifier data to disk Saves contents of amplifier RAM to a disk file. Restore amplifier data from disk Restores contents of an amplifier file from disk to amplifier RAM. Save amplifier data to flash Saves contents of amplifier RAM to amplifier flash. Restore amplifier data from flash Restores contents of amplifier flash to amplifier RAM. Manage Amplifier and Motor Data (p. 154). Copley Controls Stepnet Panel Amplifier User Guide Using CME 2 8.1.3: Main Menu Overview The CME 2 Main Menu choices are described below. Menu Selection Description For More Information File Save Amplifier Data Saves contents of amplifier’s RAM to a disk file. Manage Amplifier and Motor Data (p. 154). Restore Amplifier Data Restores contents of an amplifier file from disk to amplifier RAM. Restore CVM Control Program Prompts for a Copley Virtual Machine program file. The program in this file will replace the current program in flash. Copley Indexer 2 Program User Guide. Restore Cam Tables Prompts for a saved Cam Table file (.cct file). All tables in amplifier flash will be replaced by the ones in this file. See Copley Camming Users Guide. Exit Closes CME 2. Prompts for data-saving decision. Basic Setup Opens Basic Setup screen. Control Panel Opens Control Panel. Control Panel (p. 159). Auto Phase Opens Auto Phase tool. Auto Phase (p. 116) and Auto Phase (p. 132). Scope Opens Scope. CME 2 User Guide Error Log Opens Error Log. CME 2 User Guide Amplifier Properties Displays amplifier properties. Network Configuration Opens the CAN or DeviceNet Configuration screen. Rename Prompts for new amplifier name. Auto Tune Auto Tune for Linear Servo Motors. Gain Scheduling Opens Gain Scheduling screen. CME 2 User Guide. Communications Wizard Starts sequence of prompts to set up communications. Serial Port Setup (p. 89). Communications Log Opens Communications Log. CME 2 User Guide. Download Firmware Starts sequence of prompts to download new firmware image from disk to amplifier. Downloading Firmware (p. 157). View Scope Files Opens Trace Viewer window. CME 2 User Guide I/O Line States Opens I/O Line States window, showing high/low status of the amplifier’s inputs and outputs. CME 2 Lock/Unlock Opens screen for locking and unlocking CME 2 functionality. CME 2 User Guide. ASCII Command Line Opens screen to accept ASCII format commands. CME 2 User Guide. CME 2 User Guide Opens the CME 2 User Guide. All Documents Opens the Doc folder in the CME 2 installation folder (typically c://Program Files/Copley Motion/CME 2/Doc). This folder contains all of the related documents that were installed with CME 2. Downloads Web Page Opens default web browser with relevant pages from Copley Controls’ website. Amplifier Tools Help Basic Setup (p. 93). Renaming an Amplifier (p. 153). Software Web Page View Release Notes Opens latest CME 2 release notes in a text viewer. About Displays CME 2 version information. Copley Controls Corp. 151 Using CME 2 Stepnet Panel Amplifier User Guide 8.1.4: Functional Diagram The functional diagram, shown below, provides button-click access to most of the screens used to configure an amplifier. It also indicates the flow of control from input, across all active control loops, to motor/feedback. Only those control loop buttons that are appropriate to the operational mode appear on the diagram. The command input button reflects the selected command input. Name Input/Output CVM Control Program Input Command Description Opens Input/Output screen. For More Information Theory: Inputs (p. 42) and Outputs (p. 42). Programming instructions: Amplifier Configuration (p. 100). Opens Copley Virtual Machine screen. Copley Indexer Program User Guide. Configure the input command. Theory: Input Command Types (p. 25. Programming instructions: Basic Setup Screen (p. 93). Button label varies depending on the selected control loop input. Each opens a control loop configuration screen. Theory: Servo Modes and Control Loops (p. 18). Programming instructions: Stepper Mode Phase and Tune (p. 115), Servo Mode Phase and Tune (p. 131). Opens the Motor/Feedback screen. Motor Setup (p. 95). Home Configure and test homing. Home Function (p. 164). Configure Faults Opens Fault Configuration screen. Theory: Faults (p. 37). Programming instructions: Non-Latched and Latched Custom Outputs (p. 108). Control Loops Motor/Feedback 152 Copley Controls Stepnet Panel Amplifier User Guide Using CME 2 8.1.5: CAN or DeviceNet Information and Status Bar The Main screen displays basic CAN or DeviceNet information as shown here: Address shows the amplifier’s CAN or DeviceNet address. This value is updated on +24 Vdc power-up or reset only (see CAN Addressing [p.32] or the Copley DeviceNet Programmer’s Guide). When the Command Source is set to CAN, State shows the state of the amplifier’s CANopen state machine (see Copley Control’s CANopen Programmer’s Manual). The status bar describes the present commutation mode, motor type, and amplifier control status as shown below. It also includes a reminder that pressing the F12 function key while CME 2 is running disables the amplifier. 8.1.6: Choosing an Amplifier from a List of Amplifiers If, as shown at left, below, there is only one serial port set up for communications with an amplifier, CME 2 automatically attempts to connect to the amplifier on that port on CME 2 startup. One amplifier: Multiple amplifiers: If, as shown at right, above, multiple serial ports have been set up for communications with multiple amplifiers, CME polls all the amplifiers and displays their names in the Copley Neighborhood. To choose an amplifier, click on the amplifier name. 8.1.7: Renaming an Amplifier Each amplifier represented in the Copley Neighborhood amplifier tree has a name. The default name for an amplifier is unnamed. Use this procedure to rename an amplifier. 8.1.7.1 Select the amplifier from the Copley Neighborhood. 8.1.7.2 Choose Main Menu Amplifier Rename to open the Rename Amplifier screen. 8.1.7.3 Enter the new name. 8.1.7.4 Click OK to close the screen and save the new name or click Cancel to close the screen without saving the name. Copley Controls Corp. 153 Using CME 2 Stepnet Panel Amplifier User Guide 8.2: Manage Amplifier and Motor Data 8.2.1: Memory To maintain amplifier and motor settings, the amplifier uses volatile RAM memory and non-volatile flash memory. Data can also be saved to disk for backup and distribution. Amplifier RAM and Amplifier Flash Memory Amplifier RAM holds status data and certain user-entered information data during operation, whereas flash memory permanently stores the data for loading into amplifier RAM at power-up or reset, as described below. Amplifier RAM Amplifier Flash Contents erased when amplifier is reset or powered off. Permanent. Contents retained when the amplifier is reset or powered off. Initial contents read from flash on power-up. Contents then updated in real time to reflect certain operational conditions and changes entered with CME 2 software. At any time, the user can use CME 2 to restore data from flash into amplifier RAM. Modified only by using a Save to Flash tool or by closing certain screens (Motor/Feedback, Basic Setup, or CAN Configuration), whose contents are automatically saved to flash upon closing of the screen. How the Amplifier Uses RAM and Flash Memory As described below, some data resides in flash only, some in RAM only, and some in both. Data Resides In Data Flash only This category includes all data represented on the Motor/Feedback screen, Basic Setup screen, and CAN Configuration screen. This data is automatically saved to flash as soon as its entry is confirmed (when the user clicks the appropriate Save to Flash button, or closes the screen). Flash and RAM Includes all user-entered data represented on other screens, such as gains, limits, and I/O, and faults. Initial values for this data are factory-set in flash. They are loaded from flash to RAM with each power-up or amplifier reset. This data is saved to flash only when a user clicks the appropriate Save to Flash button. It is flushed from RAM with each power-down or amplifier reset. RAM only Includes operating status data such as actual position, actual current, and amplifier temperature. Such data is never stored in flash. It is flushed from RAM with each power-down or amplifier reset. 8.2.2: Disk Storage Amplifier Data Files and Motor Data Files At any time, the user can save certain data from RAM and flash memory to a file on disk. From the Main screen, the user can save all user-entered data represented on all screens (the data described as Flash only and Flash and on p. 154). This data is saved in a Copley Controls amplifier data file with a .ccx filename extension. From the Motor/Feedback screen, the user can save all data represented on the Motor/Feedback screen. This data is saved in a Copley Controls motor data file with a .ccm filename extension. A .ccx file can be restored to return the amplifier to a previous state or to copy settings from one amplifier to another, as described in Quick Copy Setup Procedure (p. 156). 154 Copley Controls Stepnet Panel Amplifier User Guide Using CME 2 8.2.3: Data Management Tools Amplifier Data Management Tools Operations performed using the amplifier data management tools at the top of the Main screen (shown below) affect all data, including motor/feedback data. Amplifier Data Management Tools The amplifier data management tools are described below. Icon Name Description Save amplifier data to disk Saves save all user-entered data represented on all screens from volatile and flash memory to a disk file with a .ccx filename extension. Restore amplifier data from disk Restores amplifier and motor data from a .ccx file to the amplifier’s volatile and flash memory. Note that only certain data is saved to flash by this operation (the data described as Flash only on p. 154). To assure that all data (including the data described as Flash and ) is stored in flash, use the Save amplifier data to flash tool. Save amplifier data to flash Saves contents of amplifier RAM to amplifier flash memory. Restore amplifier data from flash Restores contents the amplifier’s flash memory to amplifier’s volatile RAM. To use a data management tool, click the icon and respond to prompts. Motor Data Management Tools Operations performed using the data management tools at the bottom of the Motor/Feedback screen (shown below) affect only user-entered data represented on the Motor/Feedback screen. Motor/Feedback Data Management Tools The motor data management tools are described below. Icon Name Description Save motor data to disk Saves only motor/feedback data from the PC’s RAM to a disk file with a .ccm filename extension. Amplifier data that is not represented on the Motor/Feedback screen is not saved in this file. Restore motor data from disk Restores only motor data from a disk file with a .ccm filename extension to the amplifier’s flash memory. Amplifier data that is not represented on the Motor/Feedback screen is not affected. Save motor data to flash Saves the contents of the Motor/Feedback screen from a buffer in the PC’s RAM to the amplifier’s flash memory. Amplifier data that is not represented on the Motor/Feedback screen is not saved. Can be used to assure that all changes are saved to flash without closing the Motor/Feedback screen. Restore motor data from flash Restores only motor data from amplifier flash to amplifier RAM. Amplifier data that is not represented on the Motor/Feedback screen is not affected. Can be used before closing the Motor/Data screen to restore settings to the previously saved values. To use a data management tool, click the icon and respond to prompts. Copley Controls Corp. 155 Using CME 2 Stepnet Panel Amplifier User Guide 8.2.4: Quick Copy Setup Procedure Use this procedure to configure an amplifier/motor pair by copying configuration files that were prepared for the amplifier/motor combination. 8.2.4.1 8.2.4.2 8.2.4.3 8.2.4.4 8.2.4.5 Make sure the amplifier is connected to the PC serial port. Start CME 2 by double-clicking the CME 2 desktop shortcut icon On the Main screen, click Restore amplifier data from disk.. When prompted, navigate to the folder containing the appropriate .ccx file. Highlight the file name and then click Open to load the file data into amplifier RAM. On the Main screen, click Save to Flash. 8.2.4.6 If you do not need to load a CVM Control Program, skip to Step 8.2.4.7. To load a CVM Control Program, choose File Restore CVM Control Program. When prompted, navigate to the folder containing the appropriate .ccp file. Highlight the file name and then click Open to load the file data into flash memory. This step also results in the setting of the Indexer 2 Program option Enable Control Program on Startup. This configures the program to auto start when the amplifier is powered up or reset. 8.2.4.7 If you do not need to load a set of Cam Tables, skip to Step 8.2.4.8. To load a set of Cam Tables, choose File Restore Cam Tables. When prompted, navigate to the folder containing the appropriate .cct file. Highlight the file name and then click Open to load the file data into flash memory. 8.2.4.8 If you do not need to load a Gain Scheduling Table, the process is complete. To load a Gain Scheduling Table, choose File Restore Gain Scheduling Table. When prompted, navigate to the folder containing the appropriate .ccg file. Highlight the file name and then click Open to load the file data into flash memory. TIP: When copying amplifier data to multiple amplifiers, consider locking CME 2 to prevent accidental changes to settings. See the CME 2 User’s Guide. 156 Copley Controls Stepnet Panel Amplifier User Guide Using CME 2 8.3: Downloading Firmware 8.3.1: Acquiring Firmware Updates from Web Site 8.3.1.1 In an Internet browser, navigate to http://www.copleycontrols.com/Motion/Downloads/firmware.html 8.3.1.2 Click on the appropriate Stepnet firmware icon. 8.3.1.3 When prompted, save the file to the Firmware Image folder in the CME 2 installation folder. (The default installation folder is C:\Program Files\Copley Motion\CME 2\FirmwareImage.) The folder should now contain a file named Stepnet_Firmware.zip. 8.3.1.4 Extract the contents of the zip file to the same location. The folder should now contain the files Stepnet_Firmware.zip and the latest .cff file. 8.3.1.5 If desired, delete Stepnet_Firmware.zip to save disk space. Copley Controls Corp. 157 Using CME 2 Stepnet Panel Amplifier User Guide 8.3.2: Downloading Firmware to Amplifier 8.3.2.1 On the Main screen choose Tools Download Firmware to open the Download Firmware window. 8.3.2.2 To download new firmware without saving amplifier and motor data, click No and then proceed to Step 8.3.2.4. 8.3.2.3 To back up amplifier and motor data before downloading firmware, click Yes. 1 Use check marks to select whether to save to disk, flash, both, or neither. 2 Click OK to save data and continue to select a firmware image, or click Cancel to continue without saving data. 3 If Save Data to Disk was checked, use the Save Amplifier Data to Disk screen to browse to the folder where you want to save the .ccx file. Then enter a name in the Name field. Then click Save. When the Firmware Images window appears, proceed to Step 8.3.2.4. 8.3.2.4 Use the Firmware Images window to locate and select a firmware image file. 8.3.2.5 Click Open to begin the download. (Or click Cancel to close the screen without downloading new firmware.) A message window displays a series of progress messages: When the message window closes, the firmware download is complete. 158 Copley Controls Stepnet Panel Amplifier User Guide Using CME 2 8.4: Control Panel 8.4.1: Control Panel Overview To access the control panel, click the Control Panel icon on the Main screen. Each of the features labeled below is described in the following sections. Status indicators Monitor real-time amplifier values and operational mode Red if fault is active Yellow if warning is active Display error log Message box Control functions Jog mode controls 8.4.2: Status Indicators and Messages The Status area includes status indicator lights (described below) and a message box. All green lights indicate the amplifier is enabled and ready to accept motion commands. Indicator States/Description Motor Output State of the PWM output stage. Red if the output stage is inactive (disabled) Hardware Enabled State of the hardware enable input(s). Red if one or more enable inputs are inactive. Software Enabled State of the software enable. Red if the amplifier is disabled by software. Positive Limit State of the positive limit switch input. Red indicates an activated positive limit switch. Negative Limit State of the negative limit switch input. Red indicates an activated negative limit switch. Software Limits State of the software limits. Red indicates an activated software limit. Motor Phase Indicates a motor phasing error. Red indicates a motor phasing error exists. Motion Abort Input State of the programmed Motion Abort Input. Red indicates the input is active. CVM Control Program Status of the CVM Control Program. Home Indicates whether the axis has successfully been referenced (homed). Continued… Copley Controls Corp. 159 Using CME 2 Stepnet Panel Amplifier User Guide …continued: Indicator States/Description CAN Status The status of the CAN Bus. Yellow indicates a CAN warning limit reached. Red indicates a bus error detected. (If the CAN Status indicator is replaced by the DeviceNet Status indicator, see the Copley DeviceNet Programmer’s Guide.) Gain Scheduling Indicates whether Gain Scheduling is active. See the CME 2 User Guide. The fault indicator goes red when a fault is active. Check the status message box for a description of the most recent fault: . Check the Error Log for a full history of faults and warnings. The warning indicator goes yellow when a warning is active. Check the status message box for a description of the most recent: . Check the Error Log for a full history of faults and warnings. Message Box 160 The message box below the indicators displays the most recent active fault or warning message. Copley Controls Stepnet Panel Amplifier User Guide Using CME 2 8.4.3: Monitor Functions The Control Panel Monitor channels can display real-time values on up to three separate variables. To set up a monitor display box, click in the list box and select a variable from the list. Disabled disables the display. Other options represent the following amplifier variables. Note that some variables are only applicable when an encoder is present (in stepper or servo mode): Variable Description Commanded Current Command input to the internal current loop. Actual Current Actual current output. Profile Velocity Instantaneous velocity command output of the trajectory generator. Profile Acceleration Instantaneous commanded acceleration / deceleration rate. Commanded Velocity (Servo mode only) Command input to the internal velocity loop. Actual Motor Velocity (With encoder only) Actual motor velocity derived from the motor encoder. Velocity Error (With encoder only) Difference between Profile Velocity and Actual Motor Velocity. Commanded Position Position input to the trajectory generator. Limited Position Instantaneous position command output of the trajectory generator. Actual Position (With encoder only) Actual motor position measured by the motor encoder. Following Error (With encoder only) Difference between the Limited Position and the Actual Position. Bus Voltage Applied HV voltage Amplifier Temperature Internal power stage temperature. Mode: Displays the amplifier’s present operating mode. In camming it also displays the active cam table number. Copley Controls Corp. 161 Using CME 2 Stepnet Panel Amplifier User Guide 8.4.4: Control Functions The Control area of the screen provides functions related to overall amplifier control. The screen options vary with model and configuration. Control the operational state of the amplifier using the controls described below. Control Description Enable Click to software enable the amplifier. Disable Click to software disable the amplifier. Set Zero Position Click to set the amplifier’s actual position counter to zero. Clear Faults Click to clear all amplifier faults and latched outputs. Reset Click to reset the amplifier. ! DANGER 162 Risk of unexpected or uncontrolled motion. Using the CME 2 Set Zero Position function while the amplifier is operating under CANopen control or other command sources could cause unexpected or uncontrolled motion. Failure to heed this warning can cause equipment damage, injury, or death. Copley Controls Stepnet Panel Amplifier User Guide Using CME 2 8.4.5: Jog Mode Jog mode provides a simple way to generate forward or reverse commands as described here: 8.4.5.1 To put the amplifier in jog mode, set the Enable Jog option. 8.4.5.2 Set up a jog move by setting the following mode-specific parameters: Mode Parameter Description Current Current applied to the motor. Limited by current loop Continuous Current. Current (servo mode only) Velocity Warning: Unloaded motors may, depending on torque setting, ramp up in speed very quickly. Current Ramp The rate at which the current will increase and decrease. Jog Speed Velocity of the jog move. Limited by velocity loop Vel. Limit. Velocity Velocity of the jog move. Limited by velocity loop Vel. Limit. Acceleration Acceleration rate of the jog move. Deceleration Deceleration rate of the jog move. (servo mode only) Position 8.4.5.3 Command the move. Mode Steps Hold Pos to apply positive current to the motor or hold down Neg to apply negative current to Current (servo mode only) the motor. Velocity Hold Jog Pos to command a forward velocity or hold down Jog Neg to command a negative velocity. (servo mode only) Position Release the button to command zero current. Release the button to command zero velocity. Hold Move Pos to generate a forward move profile or hold Move Neg to generate a negative move profile. Release the button to stop movement. NOTE: A position mode jog move continuously updates the commanded position. If a following error develops with Following Error Fault is disabled, motion will not stop on button release. Instead, it stops when actual position = commanded position. Copley Controls Corp. 163 Using CME 2 Stepnet Panel Amplifier User Guide 8.5: Home Function 8.5.1: Overview The CME 2 Home function can be used to set and test homing parameters. 8.5.2: Homing Functions Settings On Main screen, click Home to open the Homing screen. 8.5.2.1 8.5.2.2 Select homing options described below. Parameter Description Software limits: Positive Position of user-defined travel limits that take effect after homing operation. Software limits: Negative 164 Deceleration Rate Deceleration rate used to stop a motor when approaching a software limit. Software limits: Disable Disables the use of software limits by setting both limits to zero. Method Homing method. See Homing Methods in the CME 2 User Guide. Direction of Motion Initial direction of motion for the homing method (Pos or Neg). Fast Velocity The velocity used to find a limit or home switch. Also used when moving to an offset position, or a resolver or Servo Tube index position. Slow Velocity The velocity used to find a switch edge, incremental or analog encoder index pulse, or hard stop. Accel/Decel The acceleration and deceleration rate used during homing. Offset Execute a move of this distance after the reference is found. Set actual position to 0 and call the new position home. Current Limit Current Delay Time Hard stop home is reached when the amplifier outputs the homing Current Limit continuously for the time specified in the Delay Time. Following Warning Shows the programmed following warning level. Actual Current Shows actual current being applied to windings during homing. Actual Position Shows actual position during homing. Copley Controls Stepnet Panel Amplifier User Guide 8.5.2.3 Optionally click Home to begin a homing sequence. 8.5.2.4 To stop the homing sequence before it is completed, click Stop. 8.5.2.5 Click Save to save the settings to flash memory. Click Exit to close the screen. Copley Controls Corp. Using CME 2 165 Using CME 2 166 Stepnet Panel Amplifier User Guide Copley Controls APPENDIX A: I2T TIME LIMIT ALGORITHM This chapter describes the algorithm used to implement the I2T limit. 2 NOTE: This chapter uses servo mode examples and terminology to describe how the I T limit works. It works the same way in stepper mode, with the following exceptions: • • servo mode continuous current = stepper mode run current servo mode peak current = stepper mode boost current Copley Controls Corp. 167 2 I T Time Limit Algorithm Stepnet Panel Amplifier User Guide A.1: I2T Algorithm A.1.1: I2T Overview The I2T current limit algorithm continuously monitors the energy being delivered to the motor using the I2T Accumulator Variable. The value stored in the I2T Accumulator Variable is compared with the I2T setpoint that is calculated from the user-entered Peak Current Limit, I2T Time Limit, and Continuous Current Limit. Whenever the energy delivered to the motor exceeds the I2T setpoint, the algorithm protects the motor by limiting the output current. A.1.2: I2T Formulas and Algorithm Operation Calculating the I2T Setpoint Value The I2T setpoint value has units of Amperes2-seconds (A2S) and is calculated from programmed 2 motor data. The setpoint is calculated from the Peak Current Limit, the I T Time Limit, and the Continuous Current Limit as follows: I2T setpoint = (Peak Current Limit2 – Continuous Current Limit2) * I2T Time Limit I2T Algorithm Operation During amplifier operation, the I2T algorithm periodically updates the I2T Accumulator Variable at a rate related to the output current Sampling Frequency. The value of the I2T Accumulator Variable is incrementally increased for output currents greater than the Continuous Current Limit and is incrementally decreased for output currents less than the Continuous Current Limit. The I2T Accumulator Variable is not allowed to have a value less than zero and is initialized to zero upon reset or +24 Vdc logic supply power-cycle. Accumulator Increment Formula At each update, a new value for the I2T Accumulator Variable is calculated as follows: I2T Accumulator Variable n+1 = I2T Accumulator Variable n +(Actual Output Current n+12 – Continuous Current Limit2) * Update period After each sample, the updated value of the I2T Accumulator Variable is compared with the I2T setpoint. If the I2T Accumulator Variable value is greater than the I2T Setpoint value, then the amplifier limits the output current to the Continuous Current Limit. When current limiting is active, the output current will be equal to the Continuous Current Limit if the commanded current is greater than the Continuous Current Limit. If instead the commanded current is less than or equal to the Continuous Current Limit, the output current will be equal to the commanded current. 168 Copley Controls Stepnet Panel Amplifier User Guide 2 I T Time Limit Algorithm A.1.3: I2T Current Limit Algorithm – Application Example I2T Example: Parameters 2 Operation of the I T current limit algorithm is best understood through an example. For this example, a motor with the following characteristics is used: • Peak Current Limit – 12 A • I2T Time Limit – 1 S • Continuous Current Limit – 6 A From this information, the I2T setpoint is: I2T setpoint = (12 A2–6 A2) * 1 S = 108 A2S See the example plot diagrams on the next page. Copley Controls Corp. 169 2 I T Time Limit Algorithm Stepnet Panel Amplifier User Guide I2T Example: Plot Diagrams The plots that follow show the response of an amplifier (configured w/ I2T setpoint = 108 A2S) to a given current command. For this example, DC output currents are shown in order to simplify the waveforms. The algorithm essentially calculates the RMS value of the output current, and thus operates the same way regardless of the output current frequency and wave shape. I2T current limit Current (A) 16 14 I_commanded 12 I_actual 10 8 6 4 2 0 0 1 2 3 4 5 6 7 Time (S) A) I2T Accumulator I2T energy (A2-S) 120 100 80 I^2T Setpoint 2 I T Setpoint 2 II^2T T Accumulator 60 40 20 0 0 1 2 3 4 5 6 7 Time (S) B) At time 0, plot diagram A shows that the actual output current follows the commanded current. Note that the current is higher than the continuous current limit setting of 6 A. Under this condition, the I2T Accumulator Variable begins increasing from its initial value of zero. Initially, the output current linearly increases from 6 A up to 12 A over the course of 1.2 seconds. During this same period, the I2T Accumulator Variable increases in a non-linear fashion because of its dependence on the square of the current. 2 2 At about 1.6 seconds, the I T Accumulator Variable reaches a value equal to the I T setpoint. At this time, the amplifier limits the output current to the continuous current limit even though the 2 commanded current remains at 12 A. The I T Accumulator Variable value remains constant during 170 Copley Controls Stepnet Panel Amplifier User Guide 2 I T Time Limit Algorithm the next 2 seconds since the difference between the actual output current and the continuous current limit is zero. At approximately 3.5 seconds, the commanded current falls below the continuous current limit and once again the output current follows the commanded current. Because the actual current is less 2 than the continuous current, the I T Accumulator Variable value begins to fall incrementally. 2 The I T Accumulator Variable value continues to fall until at approximately 5.0 seconds when the commanded current goes above the continuous current limit again. The actual output current follows the current command until the I2T Accumulator Variable value reaches the I2T setpoint and current limiting is invoked. Copley Controls Corp. 171 2 I T Time Limit Algorithm Stepnet Panel Amplifier User Guide A.2: I2T Scope Trace Variables (STX Only) 2 Two Scope Tool trace variables are available for monitoring whether the I T accumulator is accumulating or discharging. 2 The I T Amplifier Accumulator variable evaluates the accumulator against the factory set current limits of the amplifier. The I2T Motor Accumulator variable evaluates the accumulator against the user-programmed current loop values. 2 The value shown in the scope has been normalized so that 100% equals the I T setpoint. When either trace variable line reaches 100%, current limiting will be invoked. For instructions on using these variables in the Scope Tool, see the CME 2 User Guide. 172 Copley Controls APPENDIX C: THERMAL CONSIDERATIONS This chapter describes Stepnet Panel (STP) and Stepnet Panel AC (STX) amplifier operating temperature characteristics, heatsink options, and heatsink mounting instructions. Contents include: C.1: Operating Temperature and Cooling Configurations .......................................................................................................... 174 C.1.1: Stepnet Panel (STP) ............................................................................................................................................. 174 C.1.2: Stepnet Panel AC (STX) ....................................................................................................................................... 176 C.2: Heatsink Mounting Instructions .......................................................................................................................................... 179 Copley Controls Corp. 173 Thermal Considerations Stepnet Panel Amplifier User Guide C.1: Operating Temperature and Cooling Configurations C.1.1: Stepnet Panel (STP) Power Dissipation, Stepnet Panel (STP) The following chart shows the internal power dissipation for of the Stepnet Panel (STP) amplifier versus output current levels at different +HV voltages. The output current is calculated from the motion profile, motor, and load conditions. The values on the chart represent the rms (root-mean square) current that the amplifier would provide during operation. The +HV values are for the average DC voltage of the power supply. 174 Copley Controls Stepnet Panel Amplifier User Guide Thermal Considerations Max Ambient Temperature vs. Current Output, Stepnet Panel (STP) The following chart shows the maximum allowable ambient temperature of the Stepnet Panel (STP) amplifier versus output current levels at different +HV voltages. The values shown represent applications where the amplifier is installed without a heatsink and uses natural convection cooling. The addition of forced air (100 lfm minimum) or forced air and a heatsink will allow the Stepnet to operate at maximum voltage and current in a 45°C ambient environment. Thermal Resistance Stepnet Panel (STP) Configuration No Heat Sink, Convection Cooled No Heat Sink, Fan Cooled (100 LFM minimum) With Heat Sink, Fan Cooled (100 LFM minimum) With Heat Sink, Fan Cooled (200 LFM minimum) Copley Controls Corp. Thermal Resistance 2.8 °C/W 1.3 °C/W 0.8 °C/W 0.6 °C/W 175 Thermal Considerations Stepnet Panel Amplifier User Guide C.1.2: Stepnet Panel AC (STX) Power Dissipation, Stepnet Panel AC (STX) The following chart shows the internal power dissipation for of the Stepnet Panel AC (STX) amplifiers versus output current levels at different +HV voltages. The output current is calculated from the motion profile, motor, and load conditions. The values on the chart represent the rms (root-mean square) current that the amplifier would provide during operation. 176 Copley Controls Stepnet Panel Amplifier User Guide Thermal Considerations Max Ambient Temperature vs. Current Output, Stepnet Panel AC (STX-120) The following chart shows the maximum allowable ambient temperature of the Stepnet STX-120-07 amplifier versus output current levels with different cooling feature configurations. Copley Controls Corp. 177 Thermal Considerations Stepnet Panel Amplifier User Guide Max Ambient Temperature vs. Current Output, Stepnet Panel AC (STX-230-07) The following chart shows the maximum allowable ambient temperature of the Stepnet STX-230-07 amplifier versus output current levels with different cooling feature configurations. Thermal Resistance Stepnet Panel (STX) Configuration Thermal Resistance No Heat Sink, Convection Cooled 2.2 °C/W No Heat Sink, Fan Cooled (200 LFM minimum) 1.1 °C/W With Heat Sink, Convection Cooled 1.2 °C/W With Heat Sink, Fan Cooled (200 LFM minimum) 0.6 °C/W *Air flow 200 LFM minimum. 178 Copley Controls Stepnet Panel Amplifier User Guide Thermal Considerations C.2: Heatsink Mounting Instructions Use the following procedure to mount a heatsink on a Stepnet Panel amplifier. On STP models, the thermal interface between the amplifier and heat sink is a phase change material pad. On STX models, the thermal interface is a dry film interface pad. C.2.1 STX: Remove the blue protective sheet from one side of the pad. Place the phase change material on the amplifier, taking care to center the pad holes over the holes in the amplifier. Remove the clear protective sheet from the pad. Clear Protective Sheet (Discard) Dry Film Interface Pad Blue Protective Sheet (Discard) C.2.2 STP: Place the phase change material (STP) on the amplifier, taking care to center the pad holes over the holes in the amplifier. C.2.3 STP and STX: Mount the heatsink onto the amplifier taking care to see that the holes in the heatsink, phase change material or interface pad, and amplifier all line up. C.2.4 STP and STX: Install and torque the four #6-32 mounting screws to 8~10 lb-in (0.9~1.13 Nm). STP diagram shown here: Copley Controls Corp. 179 Thermal Considerations 180 Stepnet Panel Amplifier User Guide Copley Controls APPENDIX D: DETENT COMPENSATION GAIN This chapter describes the detent compensation gain feature that can be used in stepper mode to reduce detent noise. D.1: Detent Gain Tuning ............................................................................................................................................................ 182 D.1.1: Detent Gain Tuning With Encoder......................................................................................................................... 182 D.1.2: Detent Gain Tuning Without Encoder.................................................................................................................... 184 Copley Controls Corp. 181 Detent Compensation Gain Stepnet Panel Amplifier User Guide D.1: Detent Gain Tuning Some stepper motors are susceptible to detent noise. The detent gain tuning feature can be used to reduce that noise. The detent tuning process is different with an encoder than without. With an encoder, actual position is displayed in a trace and used as the primary tuning reference. Without an encoder, actual voltage is shown in the trace. With some motors, voltage changes can be subtle. In these cases, audible noise can be a better tuning reference. D.1.1: Detent Gain Tuning With Encoder D.1.1.1 D.1.1.2. D.1.1.3. 182 Make sure that amplifier and motor have been set up in stepper mode and tuned. On the CME 2 Main screen, click Detent. With Gain set to 0, adjust the velocity from 0 rpm until the greatest error is seen. Error may peak and then decrease at higher velocities, so it may be necessary to reduce velocity to return to the velocity where the greatest error is seen. Copley Controls Stepnet Panel Amplifier User Guide D.1.1.4 Detent Compensation Gain At the velocity which exhibits the worst position error, adjust Gain until position error is minimized. See example below. Note that excessive Gain can introduce more error, as shown below. Copley Controls Corp. 183 Detent Compensation Gain Stepnet Panel Amplifier User Guide D.1.2: Detent Gain Tuning Without Encoder With no encoder the trace display shows actual voltage instead of actual position. With most motors, the ouput voltage changes are subtle. In these cases, audible noise provides the best reference for tuning. D.1.2.1. Make sure that amplifier and motor have been set up in stepper mode and tuned. D.1.2.2. On the CME 2 Main screen, click Detent. D.1.2.3 With Gain set to zero, adjust velocity from zero until worst noise is heard. Error may peak at a certain velocity and then decrease at higher velocities, so it may be necessary to reduce velocity to return to the velocity where the greatest noise is heard. The trace image below was seen when the noise was loudest. D.1.2.2. At the velocity where the worst noise is heard, adjust Gain to find lowest noise level. Note that the voltage changes were subtle. The noise reduction was obvious. 184 Copley Controls APPENDIX E: ORDERING GUIDE AND ACCESSORIES This chapter lists part numbers for all Stepnet amplifiers and accessories. Contents include: E.1: Stepnet Panel (STP) Amplifier ........................................................................................................................................... 186 E.2: Stepnet Panel AC (STX) Amplifier...................................................................................................................................... 187 E.3: Stepnet Module (STM) Amplifier ........................................................................................................................................ 188 E.4: Stepnet Micro Module (STL) Amplifier................................................................................................................................ 189 Copley Controls Corp. 185 Ordering Guide and Accessories Stepnet Panel Amplifier User Guide E.1: Stepnet Panel (STP) Amplifier Stepnet Panel Model Numbers Model Number Description STP-075-07 Stepnet Panel amplifier 5/7 Adc @ 75 Vdc. STP-075-10 Stepnet Panel amplifier 10/10 Adc @ 75 Vdc. NOTE: Add “-H” to order Panel amplifier with factory-mounted heatsink. Heatsink kits may be ordered separately. Stepnet Panel (STP) Heatsink Kit Model STP-HK Qty Description 1 Heatsink 1 Heatsink thermal material 1 Heatsink hardware mounting kit Stepnet Panel (STP) Connector Kit with Solder-Cup Feedback and Control Connectors Model STP-CK Qty Ref Description Mfr. Model No. 1 J1 Housing Molex 39-01-4041 4 J1 Crimp terminal Molex 39-00-0039 1 J2 Housing Molex 39-01-4051 5 J2 Crimp terminal Molex 39-00-0039 Connector, solder-cup Norcomp: 180-026-103L001 Back shell Norcomp: 979-015-020R121 1 1 J3 Stepnet Panel (STP) CANopen Network Kit Model STP-NK Qty Ref Description Copley Controls Model No. 1 -- Sub-D 9-position female to RJ-45 adapter STP-CV CANopen Network Cable, 10 ft (3 m) generic Cat5E/Cat6E patch cable CANopen Network Terminator STP-NT 1 1 J5/J6 Stepnet Panel (STP) Individual Cable Assemblies (and Related Accessories) Model Ref Description SER-CK J4 RS-232 Serial Cable Kit (for connecting PC to amplifier) STP-CV -- Sub-D 9-position female to RJ-45 adapter (PC to CANopen cable adapter) STP-NC-10 STP-NC-01 CANopen Network Cable, 10 ft (3 m) J5/J6 STP-NT CANopen Network Cable, 1 ft (0.3 m) Mfr. Model No. generic Cat5E/Cat6E patch cable CANopen Network Terminator Software Model Description CME2 CME 2 Drive Configuration Software (CD-ROM) CML Copley Motion Libraries (CD-ROM) CMO Copley Motion Objects (CD-ROM) Order Example Order 1 STP-075-07 amplifier with factory-installed heatsink, CME 2 CD, and serial cable kit: Qty Item Description 1 STP-075-07-H Stepnet Panel (STP) stepper amplifier with heatsink installed 1 STP-CK Connector kit 1 STP-NK CANopen network kit 1 CME 2 CME 2 CD 1 SER-CK Serial Cable Kit for connecting the PC to the amplifier 186 Copley Controls Stepnet Panel Amplifier User Guide Ordering Guide and Accessories E.2: Stepnet Panel AC (STX) Amplifier Stepnet AC Panel Model Numbers Model Number Description STX-115-07 Stepnet Panel AC stepper amplifier 5/7 Adc @ 120 Vac single-phase. STX-230-07 Stepnet Panel AC stepper amplifier 5/7 Adc @ 240 Vac single-phase. Stepnet Panel AC (STX) Heatsink Kit Model STX-HK Qty Description 1 Heatsink, standard 1 Heatsink thermal material 1 Heatsink hardware mounting kit Stepnet Panel AC (STX) Connector Kit Model Qty Ref Description Mfr. Model No. 1 J1 Plug, 3 position, 7.5 mm, female Wago: 721-203/026-045/RN01-0000 1 J2 Plug, 5 position, 5.0 mm, female Wago: 721-605/000-043/RN01-0000 1 J3 3 position, 5.0 mm, female Wago: 721-103/026-047/RN01-0000 Norcomp: 180-015-103L001 J6 High density D-Sub, male, 15 position, solder-cup Backshell for J6 plug Norcomp: 979-009-020R121 High density D-Sub, male, 26 position, solder-cup Norcomp: 180-026-103L001 Backshell for J7 plug Norcomp: 979-015-020R121 Wire insertion/extraction tool Wago: 231-131 1 STX-CK 4 1 J7 1 2 J1 J2 J3 Stepnet Panel AC (STX) CANopen Network Kit Model Qty Ref 1 STX-NK 1 J4/J5 1 Description Copley Controls Model No. Sub-D 9-position female to RJ-45 adapter STX-CV CANopen cable assembly, 10 ft (3 m ) STX-NC-10 CANopen network terminator STX-NT Stepnet Panel AC (STX) Individual Cable Assemblies (and Related Accessories) Model Ref Description SER-CK J8 RS-232 Serial Cable Kit (for connecting PC to amplifier) Mfr. Model No. STX-CV Sub-D 9-position female to RJ-45 adapter (PC to CANopen cable adapter) STX-NC-10 CANopen Network Cable, 10 ft (3 m) STX-NC-01 J4/J5 STX-NT CANopen Network Cable, 1 ft (0.3 m) generic Cat5E/Cat6E patch cable CANopen Network Terminator Software Model Description CME2 CME 2 Drive Configuration Software (CD-ROM) CML Copley Motion Libraries (CD-ROM) CMO Copley Motion Objects (CD-ROM) Copley Controls Corp. 187 Ordering Guide and Accessories Stepnet Panel Amplifier User Guide E.3: Stepnet Module (STM) Amplifier Stepnet Module Model Number Model Number Description STM-075-07 Stepnet Module amplifier 5/7 Adc @ 75 Vdc. For more information, see data sheet (http://www.copleycontrols.com/Motion/Downloads/stepnetData.html). Stepnet Module Heatsink Kit Model STM-HS STM-HL Qty Description 1 Heatsink, standard 1 Heatsink thermal material 1 Heatsink hardware mounting kit 1 Heatsink, low-profile 1 Heatsink thermal material 1 Heatsink hardware mounting kit Stepnet Module Development Kit Model Description TDK-075-01 Stepnet Module Development Kit TDK-CK Stepnet Module Development Kit Connector Kit SER-CK RS-232 Serial Cable Kit (for connecting PC to development kit) Software Model Description CME2 CME 2 Drive Configuration Software (CD-ROM) CML Copley Motion Libraries (CD-ROM) CMO Copley Motion Objects (CD-ROM) 188 Copley Controls Stepnet Panel Amplifier User Guide Ordering Guide and Accessories E.4: Stepnet Micro Module (STL) Amplifier Stepnet Micro Module Model Numbers Model Number Description STL-055-04 Stepnet Micro Module amplifier 3/4.5 Adc @ 55 Vdc. For more information, see data sheet (http://www.copleycontrols.com/Motion/Downloads/stepnetData.html). STL-075-03 Stepnet Micro Module amplifier 2/3 Adc @ 55 Vdc. For more information, see data sheet (http://www.copleycontrols.com/Motion/Downloads/stepnetData.html). Stepnet Micro Development Kit (for Stepnet Micro and Stepnet Micro Module) Model Description LDK-075-01 Stepnet Micro Development Kit LDK-CK Stepnet Micro Development Kit Connector Kit SER-CK RS-232 Serial Cable Kit (for connecting PC to development kit) Software Model Description CME2 CME 2 Drive Configuration Software (CD-ROM) CML Copley Motion Libraries (CD-ROM) CMO Copley Motion Objects (CD-ROM) Copley Controls Corp. 189 Stepnet™ User Guide P/N CC95-00294-000 Revision A June 2009 2004, 2005, 2008, 2009 Copley Controls 20 Dan Road Canton, MA 02021 USA All rights reserved
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Mode : UseOutlines Page Count : 190 Create Date : 2009:06:24 13:04:56 Creator : Microsoft Word 10.0 Producer : Jaws PDF Creator, Word macro v3.3.0 Author : james smith or laura iveson Title : Copley Controls Corp Subject :EXIF Metadata provided by EXIF.tools