TN855 11 Telex DSP 223 CI (Vega) Tone Remote Adapter 1
User Manual: TN855 CI-DSP-223 Telex (Vega) DSP Tone-Remote Adapter 8. Other | LMR & HF Radio | Codan Radio
Open the PDF directly: View PDF 
.
Page Count: 6
| Download | |
| Open PDF In Browser | View PDF |
TECHNICAL NOTES MT-3/4 Radio Systems TN855 CI-DSP-223 Telex (Vega) DSP Tone-Remote Adapter The Telex DSP-223 tone-remote adapter provides a reliable means of remotely controlling Codan base stations and repeaters. The adapters can be used in conjunction with tone-remote control consoles which use the industrystandard sequential tone keying format. The DSP-223 adapters are interconnected to the distant remote control console(s) by any voice grade transmission medium such as a microwave link, a leased telephone line, or a twistedpair 600-ohm line. All DSP-223 adapters are capable of decoding the PTT tone sequence and the voice-plus-tone signals during transmission. The tone portion of the voice-plus-tone signal is removed from the transmitted voice. All models are prepared for jumper-plug conversion from four-wire-line operation to two-wire-line operation. In the four-wire mode, the panels are full duplex capable. The Telex DSP-223 tone-remote adapter provides the following features: • PTT Relay and Monitor Relay • 99 digit front panel display • PTT, Monitor and Power LED indicators • F1 and F2 Relays (programmable to any function tone) • Digital outputs for channel selection of the Codan Tx and Rx modules (programmable to any function tone) • CTCSS encode generation (64 frequencies available) • Hardware and software gain controls • Local handset port for monitoring activity through the unit and transmission back to the base or to the radio • Front panel test points and level set pots • RS-232C port on front panel for software configuration via Windows application • Ability to pass through to a second tone adapter • Single or Dual function tone recognition (16 or 100 function tones) • Morse code encoder for Automatic station identification • Voter / Ring Down Tone Generation All models have been factory tuned to the following frequencies: Guard Tone / PTT Tone: 2175 Hz Monitor Function Tone: 2050 Hz Frequency Select Function Tones (where used) F1: 1950 Hz F4: 1650 Hz F7: 1350 Hz F2: 1850 Hz F5: 1550 Hz F8: 1250 Hz F11: 950 Hz F14: 650 Hz F3: 1750 Hz F6: 1450 Hz F9: 1150 Hz F12: 850 Hz F15: 550 Hz 43 Erie Street Victoria, B.C. Canada V8V 1P8 Toll Free Canada & U.S.A. Phone: 1-800-664-4066 Fax: 1-877-750-0004 TN855 Rev 11-0-0 Aug 16 F10: 1050 Hz International Phone: 250-382-8268 Fax: 250-382-6139 © 2016 Codan Limited All rights reserved. F13: 750 Hz F16: 450 Hz Internet Email: LMRsales@codanradio.com Web: www.codanradio.com Page 1 of 6 TECHNICAL NOTES MT-3/4 Radio Systems TN855 CI-DSP-223 Telex (Vega) DSP Tone-Remote Adapter DB-25 Connector Table (Color coding for Codan Interconnect cables): 1 YEL/GRN (PTT NC) 10 RED/BLU (DIG4) 18 WHT/GRY (F2 NC) 2 YEL/BRN (PTT COM) 11 VIO/GRN (CTCSS) 19 WHT/ORG (F2 COM) 3 YEL/GRY (MON NO) 12 VIO/BRN (RX-) 20 WHT/BLU (+POWER) 4 YEL/ORG (F1 NC) 13 VIO/GRY (TX-) 21 BLK/GRN (DIG1) 5 YEL/BLU (F1 COM) 14 VIO/ORG (PTT NO) 22 BLK/BRN (DIG3) 6 RED/GRN (F2 NO) 15 VIO/BLU (MON NC) 23 BLK/GRY (DIG5) 7 RED/BRN (GND) 16 WHT/GRN (MON COM) 24 BLK/ORG (RX+) 8 RED/GRY (DIG0) 17 WHT/BRN (F1 NO) 25 BLK/BLU (TX+) 9 RED/ORG (DIG2) Installation: A female DB25 connector on the back of the subrack (J10) can be used for basic base connections to a Telex DSP-223, using a standard straight-through male-to-male DB25 cable (CBLC40-04225092). (WARNING: JU108 must be configured correctly or damage can occur. JU108 A for +13.8 Vdc / DSP-223). The A-PNL-AUX96-3 auxiliary connector can also be used to connect to the Telex board to a Codan Base Station with an AC-3E or CIBC-4E, as shown in Figure 1. Select the two or four-wire-line operation and setup jumpers J20 and J21on the Telex. For four-wire-line operation, set the jumpers in position ‘B’ and connect the four-wire leased line outgoing to Pins 4 and 5 and the receive to Pins 3 and 6 of the RJ45 modular connector. For two-wire-line operation, set the jumpers in position ‘A’ and connect the two-wire leased line to Pins 4 and 5 of the RJ45 modular connector. Ensure jumpers JU67A (or JU67X for CI-BC-4E) and JU68 are installed on the AC-3E and CI-BC-4E. On Codan MT-4R and MT-4D radio systems, the CTCSS to Subtone connection is not connected. P1 (A-PNL-AUX96-3 CONTROL CONNECTOR) CODAN RADIO EQUIPMENT 13.8V GND (GPIO 5) AUX 1 AUDIO O/P1 (GPIO 6) AUX 1 AUDIO O/P2 (GPIO 1) AUX 1 AUDIO I/P1 (GPIO 2) AUX 1 AUDIO I/P2 (GPIO 14) AUX 1 PTT K RXA SQUELCH OVERRIDE TXA SECURE / CLEAR (OPTIONAL) TXA SUBTONE I/P TXA CSEL D0 TXA CSEL D1 TXA CSEL D2 TXA CSEL D3 TELEX CI-DSP-223 TONE REMOTE ADAPTER B2 (J4-5) +POWER B32 (J4-1) GND B11 (J3-5) RX+ A11 (J3-6) C19 (J3-1) C20 (J3-2) C13 (J3-14) C10 (J4-9) C24 (J5-5) C22 (J1-4) C21 (J2-1) B21 A21 (J2-2) (J2-3) C23 (J2-4) RXTX+ TXPTT NO (INSTALL JP2) 430 OHM P/N 1101-2A0431JP MONITOR NO (INSTALL JP3) F1 NO (INSTALL JP4) CTCSS DIG0 DIG1 DIG2 DIG3 2/4 WIRE LINE IN/OUT 2/4 WIRE CONNECTIONS TO CUSTOMER EQUIPMENT 2/4 WIRE LINE OUT 4 WIRE LINE IN 4 WIRE LINE IN Jumpers Required For TXA Channel Select: TELEX: J16B (+5 V Pullup) SR-39-1: JU50A, JU51A, JU52A, JU53A, Remove JU48 On older motherboards (Serial # 123125 and earlier) the jumpers were as follows: SR-39-1: JU24B, JU25B, JU26B, JU27B, Remove JU41 Jumpers Required For PTT Operation: TELEX: JP2 Installed Figure 1: Codan Radio System to Telex DSP-223 connection 43 Erie Street Victoria, B.C. Canada V8V 1P8 Page 2 of 6 Toll Free Canada & U.S.A. Phone: 1-800-664-4066 Fax: 1-877-750-0004 International Phone: 250-382-8268 Fax: 250-382-6139 © 2016 Codan Limited All rights reserved. Internet Email: LMRsales@codanradio.com Web: www.codanradio.com TN855 Rev 11-0-0 Aug 16 TECHNICAL NOTES MT-3/4 Radio Systems TN855 CI-DSP-223 Telex (Vega) DSP Tone-Remote Adapter Telex DSP Programming: The Telex DSP-223 is typically factory programmed for the customers requirements, however, reprogramming of the Telex can be done with the Telex software contained on the CD that comes with the radio system. Ensure that the embedded firmware of the Telex is the same version as the software. To determine the embedded firmware version, turn the Telex on and the words DSP-223 will scroll across the display, then the firmware version will appear. Connect the PC to the Telex programming port on the front panel of the Telex tone remote adapter using the cable supplied with the Telex. New software and firmware for the Telex can be downloaded from www.telex.com. The software shown in Figure 2 is version 2.8 and is programmed for channels 1 through 9 with CTCSS tones of 100.0 Hz on channel 1, 203.5 Hz on channel 2 and no CTCSS on channels 3 through 9. Codan radio systems do not require the “Set Gains” or “TX Filters” sections to be accessed on the Telex DSP-223 software. The CTCSS tone is shown as always on, to allowing CTCSS to be transmitted when testing, using the microphone on the front panel of the transmitter module. On Codan MT-4R and MT-4D P25 radio systems, the CTCSS to Subtone connection is not connected and CTCSS tones are generated internally in the transmitter. Figure 2: Telex DSP-223 Programming Software 43 Erie Street Victoria, B.C. Canada V8V 1P8 Toll Free Canada & U.S.A. Phone: 1-800-664-4066 Fax: 1-877-750-0004 TN855 Rev 11-0-0 Aug 16 International Phone: 250-382-8268 Fax: 250-382-6139 © 2016 Codan Limited All rights reserved. Internet Email: LMRsales@codanradio.com Web: www.codanradio.com Page 3 of 6 TECHNICAL NOTES MT-3/4 Radio Systems TN855 CI-DSP-223 Telex (Vega) DSP Tone-Remote Adapter TELEX FUNCTION DSP-223 R O LI UN D N E R TX AD I C OT TC X S LI S N E LI RX N E R TX AD + I R OT AD X IO + R LI X N E TX LI N E R X R AD IO TX R AD IO R X C TC SS HANDSET G PROGRAMMING PORT POWER PTT MONITOR PTT IC Telex DSP Alignment / Tuning Procedures: Initial Setup Step 1 - Program the Telex using the Telex programming software and ensure all jumpers are correctly installed. AC-3E Audio Control Card and CI-BC-4E Base Control Card Tuning Step 2 - Disconnect the Telex tone remote from the Codan radio system. Step 3 - Apply a 1.0 KHz tone @ 0 dBm (775 mV) to the GPIO 1 (Aux 1 I/P 1) and GPIO 2 (Aux 1 I/P 2) balanced auxiliary audio input on the Codan radio system. Step 4 - Adjust R120 (Aux In 1 to TXA) for a transmitter deviation of ± 3 KHz (WB), ± 1.5 KHz (NB). Step 5 - Inject a 1.0 KHz tone @ a deviation of ± 3 KHz (WB), ± 1.5 KHz (NB) into Receiver A. Step 6 - Adjust R13 (RXA to Aux Out 1) for an audio level of 0 dBm (775 mV @ 600 ohms) across GPIO 5 (Aux 1 O/P 1) and GPIO 6 (Aux 1 O/P 2) on the Codan radio system. Note: MT-4R and MT-4D P25 Receiver modules have a higher audio level output when receiving a digital signal (as opposed to analog). When using these receiver modules in digital mode, adjust R13 for an audio level of -8.0 dBm (308 mV @ 600 ohms). Step 7 - Connect the Telex tone remote to the Codan radio system. Telex Line and Radio Level Tuning Step 8 - Using an appropriate test set (Telex C-2002), apply a 1.0 KHz tone @ 0 dBm into the tone remote. Step 9 - On the front panel of the Telex, monitor the receive line level (AC Voltmeter across LINE RX and GROUND) and adjust the LINE RX pot for 500 mV. This level can vary with the cable length between the console and the remote. Step 10 - On the front panel of the Telex, monitor the transmit radio level (AC Voltmeter across RADIO TX+ and RADIO TX-) and adjust the RADIO TX pot for 0 dBm (775 mV) or a transmitter deviation of ± 3 KHz (WB), ± 1.5 KHz (NB). Step 11 - Inject a 1.0 KHz tone @ a deviation of ± 3 KHz (WB), ± 1.5 KHz (NB) into Receiver A. Step 12 - On the front panel of the Telex, monitor the receive radio level (AC Voltmeter across RADIO RX and GROUND) and adjust the RADIO RX pot for 0 dBm (775 mV). Note: When adjusting R13 in Step 6 for an audio level of -8.0 dBm (308 mV), adjust the RADIO RX pot for -8.0 dBm (308 mV). Step 13 - On the front panel of the Telex, monitor the transmit line level (AC Voltmeter across LINE TX+ and LINE TX-) and adjust the LINE TX pot for 0 dBm (775 mV). This level can vary with the cable length between the console and the remote. Step 14 - Set the Communications analyzer to monitor the deviation level of the transmitter CTCSS encode tone (enable 300 Hz Lowpass filter). Step 15 - Key the Telex test set with a CTCSS tone programmed and adjust the CTCSS pot on the front panel of the Telex for a transmitter deviation of ± 500 Hz (WB), ± 350 Hz (NB). 43 Erie Street Victoria, B.C. Canada V8V 1P8 Page 4 of 6 Toll Free Canada & U.S.A. Phone: 1-800-664-4066 Fax: 1-877-750-0004 International Phone: 250-382-8268 Fax: 250-382-6139 © 2016 Codan Limited All rights reserved. Internet Email: LMRsales@codanradio.com Web: www.codanradio.com TN855 Rev 11-0-0 Aug 16 TECHNICAL NOTES MT-3/4 Radio Systems TN855 CI-DSP-223 Telex (Vega) DSP Tone-Remote Adapter Bypassing the AC-3E Audio Control Card and CI-BC-4E Base Control Card: The AC-3E Audio Control Card and CI-BC-4E Base Control Card can be bypassed and the MT-4E Receiver and Transmitter can be connected directly to the Telex adapter. The control card needs to be removed from the subrack, or unwanted loading could occur. The following receiver and transmitter tuning changes would be required: Transmitter Setup - Apply a 1.0 KHz tone @ 0 dBm (775 mV) to the Tx A Bal I/P1 (J1-1) and Tx A Bal I/P 2 (J1-2) balanced audio input and adjust the RSS software Balanced Audio Deviation Level for a transmitter deviation of ± 3 KHz (WB), ± 1.5 KHz (NB). Receiver Setup - Inject a 1.0 KHz tone @ a deviation of ± 3 KHz (WB), ± 1.5 KHz (NB) into the receiver and adjust the RSS software Balanced Output Audio Level for an audio level of 0 dBm (775 mV @ 600 ohms) across Rx A Bal O/P 1 (J1-5) and Rx A Bal O/P 2 (J1-6). The DB25 (J10) can be jumpered for Balanced Audio direct to / from the receiver and transmitter as follows: JU104 JU105 JU106 A = RX A Bal O/P2 A = TX A Bal I/P2 A = TX A Bal I/P1 JU107 JU108 A = RX A Bal O/P1 A = DSP-223 / +13.8 V On the Wiring diagram for the A-PNLAUX96-3, the following connections change: (GPIO 5) AUX 1 AUDIO O/P1(J3-5) (GPIO 6) AUX 1 AUDIO O/P2 (J3-6) (GPIO 1) AUX 1 AUDIO I/P1 (J3-1) (GPIO 2) AUX 1 AUDIO I/P2 (J3-2) (GPIO 14) AUX 1 PTT K (J3-14) 43 Erie Street Victoria, B.C. Canada V8V 1P8 Rx A Bal O/P 1 (J1-5) Rx A Bal O/P 2 (J1-6) Tx A Bal I/P1 (J1-1) Tx A Bal I/P 2 (J1-2) Tx A PTT (J1-3) Toll Free Canada & U.S.A. Phone: 1-800-664-4066 Fax: 1-877-750-0004 TN855 Rev 11-0-0 Aug 16 International Phone: 250-382-8268 Fax: 250-382-6139 © 2016 Codan Limited All rights reserved. Internet Email: LMRsales@codanradio.com Web: www.codanradio.com Page 5 of 6 TECHNICAL NOTES MT-3/4 Radio Systems TN855 CI-DSP-223 Telex (Vega) DSP Tone-Remote Adapter This Page Intentionally Left Blank 43 Erie Street Victoria, B.C. Canada V8V 1P8 Page 6 of 6 Toll Free Canada & U.S.A. Phone: 1-800-664-4066 Fax: 1-877-750-0004 International Phone: 250-382-8268 Fax: 250-382-6139 © 2016 Codan Limited All rights reserved. Internet Email: LMRsales@codanradio.com Web: www.codanradio.com TN855 Rev 11-0-0 Aug 16
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : plunness Create Date : 2017:11:23 15:22:35-08:00 Modify Date : 2017:11:23 15:22:35-08:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Producer : Acrobat Distiller 10.1.16 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Format : application/pdf Title : TN855-11 Telex DSP-223.indd Creator : plunness Document ID : uuid:94a7089b-5f94-43fc-822d-0548136f00e3 Instance ID : uuid:0100d7d3-abe6-42d5-a1f8-7e51c1f2b324 Page Count : 6EXIF Metadata provided by EXIF.tools