VISHAY Leaded Solid Electrolyte Tantalex Caps INTERACTIVE
User Manual: VISHAY-Leaded-Solid-Electrolyte-Tantalex-Caps-INTERACTIVE
Open the PDF directly: View PDF 
.
Page Count: 153
| Download | |
| Open PDF In Browser | View PDF |
VISHAY I N T E R T E C H N O L O G Y , I N C . INTERACTIVE data book LEADED SOLID ELECTROLYTE TANTALEX ® CAPACITORS vishay vse-db0029-0805 Notes: 1. To navigate: a) Click on the Vishay logo on any datasheet to go to the Contents page for that section. Click on the Vishay logo on any Contents page to go to the main Table of Contents page. b) Click on the products within the Table of Contents to go directly to the datasheet. c) Use the scroll or page up/page down functions. d) Use the Adobe ® Acrobat ® page function in the browser bar. 2. To search the text of the catalog use the Adobe ® Acrobat ® search function. One of the World’s Largest Manufacturers of Discrete Semiconductors and Passive Components V I S H AY I N T E R T E C H N O L O G Y, I N C . DATA B O O K leaded solid electrolyte tantalex ® capacitors Hermetic Seal, A xial Leaded Molded Case, Radial and A xial Leaded R e s i n C o a t e d , R a d i a l a n d Tr i p o l e L e a d e d CECC 30201 Q ualifie d St yles M i l i t a r y M I L- P R F - 3 9 0 0 3 Q u a l i f i e d S t y l e s w w w. v i s h a y. c o m SEMICONDUCTORS Rectifiers Schottky (single, dual) Standard, Fast, and Ultra-Fast Recovery (single, dual) Bridge Superectifier ® Sinterglass Avalanche Diodes High-Power Diodes and Thyristors High-Power Fast-Recovery Diodes Phase-Control Thyristors Fast Thyristors P rod u ct L istings Small-Signal Diodes Schottky and Switching (single, dual) Tuner/Capacitance (single, dual) Bandswitching PIN Zener and Suppressor Diodes Zener (single, dual) TVS (TRANSZORB®, Automotive, ESD, Arrays) FETs Low-Voltage TrenchFET® Power MOSFETs High-Voltage TrenchFET® Power MOSFETs High-Voltage Planar MOSFETs JFETs RF Transistors Bipolar Transistors (AF and RF) Dual Gate MOSFETs MOSMICs® Optoelectronics IR Emitters and Detectors, and IR Receiver Modules Optocouplers and Solid-State Relays Optical Sensors LEDs and 7-Segment Displays Infrared Data Transceiver Modules Custom Products ICs Power ICs Analog Switches RF Transceivers and Receiver Modules ICs for Optoelectronics Modules Power Modules (contain power diodes, thyristors, MOSFETs, IGBTs) DC/DC Converters Passive Components Resistive Products Foil Resistors Film Resistors Metal Film Resistors Thin Film Resistors Thick Film Resistors Metal Oxide Film Resistors Carbon Film Resistors Wirewound Resistors Power Metal Strip® Resistors Chip Fuses Variable Resistors Cermet Variable Resistors Wirewound Variable Resistors Conductive Plastic Variable Resistors Networks/Arrays Non-Linear Resistors NTC Thermistors PTC Thermistors Varistors Magnetics Inductors Transformers Capacitors Tantalum Capacitors Molded Chip Tantalum Capacitors Coated Chip Tantalum Capacitors Solid Through-Hole Tantalum Capacitors Wet Tantalum Capacitors Ceramic Capacitors Multilayer Chip Capacitors Disc Capacitors Film Capacitors Power Capacitors Heavy-Current Capacitors Aluminum Capacitors Silicon RF Capacitors Strain Gage Transducers and Stress Analysis Systems PhotoStress® Strain Gages Load Cells Force Transducers Instruments Weighing Systems Specialized Strain Gage Systems Leaded Solid Electrolyte TANTALEX® Capacitors Vishay Sprague, Inc. 15 Daigle Lane Suite 103 Sanford, ME 04073 U. S. A. Phone: +1 207 490 7205 Fax: +1 207 490 7213 www.vishay.com NOTICE Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc., or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Vishay for any damages resulting from such improper use or sale. Table of Contents Vishay Sprague Leaded Solid Electrolyte TANTALEX® Capacitors Military Style to Commercial Equivalent Product Index ..................................................................................................... Parameter Comparison Guide, Solid Tantalum Leaded Capacitors .................................................................................. Introduction, Solid Tantalum Capacitors ............................................................................................................................ AC Ripple Application Notes, Solid Tantalum Capacitors.................................................................................................. Mounting for Through-hole Components ........................................................................................................................... Total Quality Commitment, Tantalum Capacitors .............................................................................................................. Quick Reference Guide, Solid Tantalum Leaded Capacitors ............................................................................................ SOLID TANTALUM LEADED CAPACITORS METAL CASE 150D Solid Electrolyte TANTALEX® Capacitors, Hermetic Seal, Axial Leaded ......................... 152D Solid Electrolyte TANTALEX® Capacitors, Hermetic Seal, Axial Leaded, Extended Capacitance ................................................................................................... 550D Solid Electrolyte TANTALEX® Capacitors, Hermetic Seal, Axial Leaded, For High Frequency Power Supplies .............................................................................. M39003/01/03/09 Styles CSR13, 21, 23, Solid Electrolyte TANTALEX® Capacitor MIL-PRF-39003 Qualified, Hermetic Seal, Axial Leaded, Tubular.................................. CTS1, CTS13, 749DX Solid Electrolyte TANTALEX® Capacitors CECC30201Qualified, Hermetic Seal, Axial Leaded, Tubular 30201-002, Style CTS1 30201-005, Style CTS13 30201-001/011/012/029, Style 749DX............................................................................ SUBMINIATURE CASE CX06 CX16 HA SHA TC STC RESIN COATED 173D 790D 199D 299D 489D, 499D ETPW ETQW 2 3 4 7 11 13 14 18 27 31 39 54 Solid Leaded TANTALEX® Capacitors .............................................................................. Solid Leaded TANTALEX® Capacitors .............................................................................. Solid Leaded TANTALEX® Capacitors, Polar or Non-Polar............................................... Solid Leaded TANTALEX® Capacitors, Polar or Non-Polar............................................... Solid Leaded TANTALEX® Capacitors, Polar or Non-Polar............................................... Solid Leaded TANTALEX® Capacitors, Polar or Non-Polar............................................... 64 67 70 78 84 91 Solid Electrolyte TANTALEX® Capacitors, Molded Case, Axial Leaded............................ Solid Electrolyte TANTALEX® Capacitors, Molded Case, Radial Leaded, European Style ............................................................................................................... Solid Electrolyte TANTALEX® Capacitors, Resin Coated, Radial Leaded......................... Solid Electrolyte TANTALEX® Capacitors, Resin Coated, Tripole Triple Leaded .............. Solid Electrolyte TANTALEX® Capacitors, Resin Coated, Radial Leaded, European Style ............................................................................................................... Solid Electrolyte TANTALEX® Capacitors, Resin Coated, Radial Leaded, VISHAY Roederstein Type ............................................................................................. Solid Electrolyte TANTALEX® Capacitors, Resin Coated, Radial Leaded, High Reliability,VISHAY Roederstein Type..................................................................... 98 104 111 117 123 131 138 All Military Products are manufactured with DSCC approved designs, processes and testing. Commercial products are manufactured to be in compliance with EIA Industry Standards Revision: 12-Feb-08 www.vishay.com 1 Military Product Index Vishay Sprague Military Style to Commercial Equivalent Product Index SOLID TANTALUM LEADED CAPACITORS M39003/01/03/09 M39003/01 M39003/03 M39003/09 MILITARY STYLE CSR13 CSR23 CSR21 CX05* CX02*, CX12* CX06, CX16 Styles CSR13, 21, 23, Solid Electrolyte TANTALEX® Capacitors, MIL-PRF-39003 Qualified, Metal Case Hermetic Seal, Axial, Tubular ........................... Military Style CSR13, Standard Ratings Chart ............................................................... Military Style CSR21, Standard Ratings Chart .............................................................. Military Style CSR23, Standard Ratings Chart .............................................................. 39 39 39 39 COMMERCIAL TYPE EQUIVALENT 150D, Solid Electrolyte TANTALEX® Capacitors, Hermetic Seal, Axial............................. 18 152D, Solid Electrolyte TANTALEX® Capacitors, Hermetic Seal, Axial, Extended Capacitance.................................................................................................... 27 550D, Solid Electrolyte TANTALEX® Capacitors, Hermetic Seal, Axial, For High Freqency Power Supplies ................................................................................ 31 173D, Solid Electrolyte TANTALEX® Capacitors, Molded Case, Axial .............................. 98 199D, Solid Electrolyte TANTALEX® Capacitors, Resin Coated, Radial ........................... 111 TC, Subminiature, Leaded Solid Tantalum Capacitors................................................... 84 Note: * Military Style CX-MIL-C-49137 not available All Military Products are manufactured with DSCC approved designs, processes and testing. Commercial products are manufactured to be in compliance with EIA Industry Standards www.vishay.com 2 Revision: 12-Feb-08 Parameter Comparison Guide Vishay Sprague SOLID TANTALUM LEADED CAPACITORS - HERMETIC SEAL, METAL CASE MODEL MIL SPEC/ TYPE OUTLINE DRAWING CAPACITANCE RANGE (µF) WORKING VOLTAGES AT 85 °C CASE SIZES PAGE 150D - Polar MIL-PRF-39003/01 (CSR13) 0.056 - 330 6 - 125 VDC A, B, R, S 18 152D - Polar MIL-PRF-39003/03 (CSR23) 1.2 - 1000 6 - 50 VDC A, B, R, S 27 550D - Polar MIL-PRF-39003/09 (CSR21) 5.6 - 330 6 - 50 VDC R, S 31 Military Parts CSR13 - Metal Case Axial CSR21 - Metal Case Axial CSR23 - Metal Case Axial MIL-PRF-39003/01 MIL-PRF-39003/09 MIL-PRF-39003/03 0.056 - 330 6 - 100 VDC 6 - 50 VDC 6 - 50 VDC A, B, C, D C, D A, B, C, D 39 To CECC 30201 CTS1 - Metal Case Axial CTS13 - Metal Case Axial 749DX - Metal Case Axial 30201 - 002 30201 - 005 30201 - 001/ 011/012/029 0.1 - 330 0.1 - 330 0.068 - 1000 6 - 125 VDC 6 - 63 VDC 6 - 63 VDC A, B, C, D A, B, C, D A, B, C, D 54 SOLID TANTALUM LEADED CAPACITORS - NON-HERMETIC SEAL, MOLDED CASE, RESIN COATED CAPACITANCE RANGE (µF) WORKING VOLTAGES AT 85 °C CASE SIZES PAGE 173D - Molded Axial 0.10 - 330 2 - 50 VDC U, V, W, X, Y 98 199D - Dipped Radial 0.1 - 680 3 - 50 VDC A, B, C, D, E, F 111 299D - Dipped Radial 0.1 - 680 3 - 50 VDC A, B, C, D, E, F 117 489D, 499D - Dipped Radial 0.1 - 680 3 - 50 VDC A, B, C, D, E, F, H, M, N, R 123 790D - Molded Radial 0.1 - 330 6 - 50 VDC A, B, C, D 104 ETPW - Dipped Radial Vishay Roederstein Type 0.1 - 330 3 - 50 VDC P1A to P6R 131 ETQW - Dipped Radial Vishay Roederstein Type, High Reliability 0.1 - 330 3 - 50 VDC Q1A to Q6R 138 MODEL MIL SPEC/ TYPE OUTLINE DRAWING Notes: • All Axial Polar capacitors are available tape and reeled per EIA RS-296 • Model 199D/299D capacitors are available tape and reeled per EIA RS-468 Document Number: 40033 Revision: 18-Apr-08 For technical questions, contact: tantalum@vishay.com www.vishay.com 3 Introduction Vishay Sprague Solid Tantalum Capacitors Tantalum electrolytic capacitors are the preferred choice in applications where volumetric efficiency, stable electrical parameters, high reliability and long service life are primary considerations. The stability and resistance to elevated temperatures of the tantalum/tantalum oxide/manganese dioxide system make solid tantalum capacitors an appropriate choice for today’s surface mount assembly technology. Vishay Sprague has been a pioneer and leader in this field, producing a large variety of tantalum capacitor types for consumer, industrial, automotive, military and aerospace electronic applications. Tantalum is not found in its pure state. Rather, it is commonly found in a number of oxide minerals, often in combination with Columbium ore. This combination is known as “tantalite” when its contents are more than one-half tantalum. Important sources of tantalite include Australia, Brazil, Canada, China and several African countries. Synthetic tantalite concentrates produced from tin slags in Thailand, Malaysia and Brazil are also a significant raw material for tantalum production. Electronic applications and particularly capacitors consume the largest share of world tantalum production. Other important applications for tantalum include cutting tools (tantalum carbide), high temperature super alloys, chemical processing equipment, medical implants and military ordnance. Vishay Sprague is a major user of tantalum materials in the form of powder and wire for capacitor elements and rod and sheet for high temperature vacuum processing. Tantalum pentoxide compound possesses high dielectric strength and a high dielectric constant. As capacitors are being manufactured, a film of tantalum pentoxide is applied to their electrodes by means of an electrolytic process. The film is applied in various thicknesses and at various voltages and although transparent to begin with, it takes on different colors as light refracts through it. This coloring occurs on the tantalum electrodes of all types of tantalum capacitors. Rating for rating, tantalum capacitors tend to have as much as three times better capacitance/volume efficiency than aluminum electrolytic capacitors. An approximation of the capacitance/volume efficiency of other types of capacitors may be inferred from the following table, which shows the dielectric constant ranges of the various materials used in each type. Note that tantalum pentoxide has a dielectric constant of 26, some three times greater than that of aluminum oxide. This, in addition to the fact that extremely thin films can be deposited during the electrolytic process mentioned earlier, makes the tantalum capacitor extremely efficient with respect to the number of microfarads available per unit volume. The capacitance of any capacitor is determined by the surface area of the two conducting plates, the distance between the plates and the dielectric constant of the insulating material between the plates. COMPARISON OF CAPACITOR DIELECTRIC CONSTANTS DIELECTRIC K DIELECTRIC CONSTANT Air or Vacuum 1.0 THE BASICS OF TANTALUM CAPACITORS Most metals form crystalline oxides which are non-protecting, such as rust on iron or black oxide on copper. A few metals form dense, stable, tightly adhering, electrically insulating oxides. These are the so-called “valve” metals and include titanium, zirconium, niobium, tantalum, hafnium and aluminum. Only a few of these permit the accurate control of oxide thickness by electrochemical means. Of these, the most valuable for the electronics industry are aluminum and tantalum. Capacitors are basic to all kinds of electrical equipment from radios and television sets to missile controls and automobile ignitions. Their function is to store an electrical charge for later use. Capacitors consist of two conducting surfaces, usually metal plates, whose function is to conduct electricity. They are separated by an insulating material or dielectric. The dielectric used in all tantalum electrolytic capacitors is tantalum pentoxide. www.vishay.com 4 Paper 2.0 - 6.0 Plastic 2.1 - 6.0 Mineral Oil 2.2 - 2.3 Silicone Oil 2.7 - 2.8 Quartz 3.8 - 4.4 Glass 4.8 - 8.0 Porcelain 5.1 - 5.9 Mica 5.4 - 8.7 Aluminum Oxide 8.4 Tantalum Pentoxide 26 Ceramic For technical questions, contact: tantalum@vishay.com 12 - 400 000 Document Number: 40058 Revision: 18-Apr-08 Introduction Solid Tantalum Capacitors Vishay Sprague 150D AND MIL STYLE CSR13 HERMETICALLY-SEALED, SOLID ELECTROLYTE (MILITARY SPECIFICATION NO. MIL-PRF-39003) SINTERED TANTALUM PELLET (ANODE) TANTALUM PENTOXIDE (DIELECTRIC) NICKEL LEAD (NEGATIVE) LEAD SWAGGED TO BOTTOM OF CASE MANGANESE DIOXIDE (SOLID ELECTROLYTE, CATHODE) GRAPHITE METAL CASE SILVER TANTALUM WIRE WELDED TO OR IMBEDDED IN TANTALUM PELLET LOWER END OF CASE FILLED WITH SOLDER WELD METAL EYELET GLASS NICKEL LEAD (POSITIVE) SOLDER METAL RING GLASS FUSED TO METAL EYELET AND METAL RING FOR HERMETIC SEAL Voltage Range: 6 WVDC to 125 WVDC Capacitance Range: 0.056 µF to 330 µF Size Range: 0.125" [3.175 mm] Ø x 0.250" [6.350 mm] long to 0.341" [8.661 mm] Ø x 0.750" [19.050 mm] long Primary Applications: Industrial and military equipment where reliability, low leakage current, low dissipation factor and stability with time and temperature are required. In the tantalum electrolytic capacitor, the distance between the plates is very small since it is only the thickness of the tantalum pentoxide film. As the dielectric constant of the tantalum pentoxide is high, the capacitance of a tantalum capacitor is high if the area of the plates is large: C = eA ------t In solid electrolyte capacitors, a dry material, manganese dioxide, forms the cathode plate. The anode lead wire from the tantalum pellet consists of two pieces. A tantalum lead embedded in, or welded to the pellet, which is in turn connected to a termination or lead wire. The drawings clearly show the construction details of the frequently used types of tantalum capacitors. VISHAY'S LINE OF HIGH QUALITY LEADED TANTALUM CAPACITORS where C = capacitance Vishay manufactures two categories of leaded tantalum capacitors: e = dielectric constant A = surface area of the dielectric 1. Solid electrolyte, sintered anode leaded tantalum capacitors as shown in this data book t = thickness of the dielectric Tantalum capacitors contain either liquid or solid electrolytes. The liquid electrolyte in wet slug capacitors generally sulfuric acid - forms the cathode (negative) plate. Document Number: 40058 Revision: 18-Apr-08 2. Wet electrolyte, sintered anode leaded tantalum capacitors - see Vishay data book, Wet Tantalum Capacitors (VSE-DB0030) For technical questions, contact: tantalum@vishay.com www.vishay.com 5 Introduction Vishay Sprague Solid Tantalum Capacitors SOLID ELECTROLYTE TANTALUM CAPACITORS Solid electrolyte, sintered anode tantalum capacitors in their original hermetically-sealed designs differ from the wet versions in their electrolyte. Here, the electrolyte is manganese dioxide, which is formed on the tantalum pentoxide dielectric layer by impregnating the pellet with a solution of manganous nitrate. The pellets are then heated in an oven and the manganous nitrate is converted to manganese dioxide. 199D EPOXY-DIPPED, SOLID ELECTROLYTE EPOXY COATING WELD TANTALUM PENTOXIDE (DIELECTRIC) NICKEL LEAD (POSITIVE) MANGANESE DIOXIDE (SOLID ELECTROLYTE) The pellet is next coated with graphite followed by a layer of metallic silver, which provides a solderable surface between the pellet and the can in which it will be enclosed. The pellets, with lead wire and header attached, are inserted into the can where the pellet is held in place by solder. The can cover is also soldered into place. After assembly, the capacitors are tested and inspected to assure long life and reliability. Another variation of the solid electrolyte tantalum capacitor encases the element in plastic resins, such as epoxy materials. It offers excellent reliability and high stability for consumer and commercial electronics with the added feature of low cost. Surface mount designs of “Solid Tantalum” capacitors use leadframes or leadframeless designs as shown in the accompanying drawings. SINTERED TANTALUM PELLET (ANODE) GRAPHITE SILVER NICKEL LEAD (NEGATIVE) TANTALUM WIRE WELDED TO TANTALUM PELLET CATHODE LEAD SOLDERED TO SILVERED AREA OF CAPACITOR SECTION Voltage Range: 3 WVDC to 50 WVDC Capacitance Range: 0.10 µF to 680 µF Size Range: 0.177" [4.496 mm] diameter x 0.340" [8.636 mm] high to 0.380" [9.652 mm] diameter x 0.710" [18.034 mm] high Primary Applications: On printed circuit boards in entertainment, commercial and industrial equipment where low cost, small size, high stability, low DC leakage and low dissipation factor are important. TANTALUM CAPACITORS FOR ALL DESIGN CONSIDERATIONS In choosing between the two basic types of tantalum capacitors, the circuit designer customarily uses wet sintered anode capacitors, or wet “slug” tantalum capacitors, where the lowest DC leakage is required. The conventional silver can design will not tolerate any reverse voltages. However, in military or aerospace applications, tantalum cases are used in place of silver cases where utmost reliability is desired. The tantalum cased wet slug units will withstand reverse voltages up to 3 V, will operate under higher ripple currents and can be used at temperatures up to + 392 °F (+ 200 °C). Solid electrolyte designs, which are the least expensive for a given rating, are used in many applications where their very small size for a given unit of capacitance is of importance. www.vishay.com 6 They will typically withstand up to about 10 % of the rated DC working voltage in a reverse direction. Also important are their good low temperature performance characteristics and freedom from corrosive electrolytes. Vishay Sprague patented the original solid electrolyte capacitors and was the first to market them in 1956. (Vishay has the broadest line of tantalum capacitors and has continued its position of leadership in this field.) Datasheets covering the various types and styles of Vishay tantalum capacitors for consumer and entertainment electronics, for industrial and for military applications are available where detailed performance characteristics must be specified. For technical questions, contact: tantalum@vishay.com Document Number: 40058 Revision: 18-Apr-08 Application Notes Vishay Sprague AC Ripple Current Calculations INTRODUCTION Solid tantalum capacitors are preferred for filtering applications in small power supplies and DC/DC converters in a broad range of military, industrial and commercial systems including computers, telecommunications, instruments and controls and automotive equipment. Solid tantalum capacitors are preferred for their high reliability, long life, extended shelf life, exceptional stability with temperature and their small size. Their voltage range is 4 to 50 V for the most common types. Tantalum chip capacitors for surface mount applications are manufactured in very small sizes and are compatible with standard pick-and-place equipment. Looking closely at the internal structure of the pellet, we see that it is made of grains of tantalum powder sintered to each other. A solid tantalum capacitor is equivalent to many small capacitors in parallel, one for each grain of powder. This configuration produces a very large surface area, therefore a large capacitance in a relatively small volume. TANTALUM PELLET SIMPLIFIED VIEW TANTALUM ANODE LEAD The electronics industry has moved to smaller and smaller power supplies and higher switching frequencies, with an increased requirement for capacitors with smaller size and operating characteristics better suited to high frequencies. This application note briefly describes the construction of solid tantalum capacitors, the concept of Equivalent Series Resistance (ESR) and presents calculations for power dissipation and voltage limitations for both low and high frequency applications. TANTALUM Ta2O5 MnO2 CARBON METALLIZED OUTER ELECTRODE CONSTRUCTION The solid tantalum capacitor consists of a sintered tantalum pellet, the anode, on which a tantalum oxide dielectric is formed by electrolysis. The pellet is then coated with manganese dioxide for the cathode. Positive and negative terminations are attached to this pellet and the assembly may be conformally coated, molded or sealed in a metal case. SOLID DIPPED TANTALUM CAPACITOR CROSS SECTION EPOXY COATING WELD SINTERED TANTALUM PELLET (ANODE) TANTALUM PENTOXIDE (DIELECTRIC) NICKEL LEAD (POSITIVE) MANGANESE DIOXIDE (SOLID ELECTROLYTE) GRAPHITE EQUIVALENT SERIES RESISTANCE (ESR) A capacitor offers internal resistance to AC current, called the Equivalent Series Resistance (ESR). At lower frequencies, this is mainly the resistance of the dielectric. At higher frequencies, the resistance of the manganese dioxide in the voids between the grains is predominant. Because the resistivity of manganese dioxide is inversely proportional to temperature, the ESR of solid tantalum capacitors at high frequencies decreases as temperature increases. POWER DISSIPATION LIMITATION When AC current is applied to a solid tantalum capacitor, the resistance (ESR) that opposes the flow of current results in heat generation, according to the formula: 2 (1) P = I × ESR SILVER CATHODE LEAD SOLDERED TO SILVERED AREA OF CAPACITOR SECTION NICKEL LEAD (NEGATIVE) TANTALUM WIRE WELDED TO TANTALUM PELLET Document Number: 40057 Revision: 26-Nov-07 The power (P) dissipated in the capacitor results in an elevation of temperature. The allowable temperature rise of a capacitor due to power dissipation is determined by experience. For example, this value is + 20 °C maximum for molded chip capacitors. This in turn limits the power that the capacitor can dissipate. For technical questions, contact: tantalum@vishay.com www.vishay.com 7 Application Notes AC Ripple Current Calculations Vishay Sprague VOLTAGE LIMITATION The power a capacitor can dissipate is also limited by the applied DC voltage. The operating voltage should not be allowed to rise above the rated voltage (nor should it drop below zero, since the solid tantalum capacitor is a polarized component). Assuming the capacitor is biased at half the rated voltage, which is the optimum use condition, the limiting value of the voltage is, for a sinusoidal waveform: where Irms is the maximum permissible rms current in milliamperes, C the capacitance minus the capacitance tolerance in microfarads and V the rated voltage in volts. All above calculations assume the capacitor is properly biased at half the rated voltage. If this is not the case, Vrms becomes (8) V P ⁄ 2 where VP = Vrated - Vbias or Vbias, whichever is lower. (2) V rms = V pp ⁄ 2 2 = R V ⁄ 2 2 Vrms for each value of RV (Rated voltage) are: CURRENT LIMITATION (HIGH FREQUENCY) RATED VOLTAGE Vrms MAXIMUM 4 10 20 25 35 40 50 1.42 5.30 7.07 8.84 12.37 14.14 17.68 At frequencies in the 10 kHz to several 100 kHz range, the power dissipation becomes the limiting factor. The following formula gives the maximum permissible ripple current for a sinusoidal wave form: (9) I rms = CURRENT LIMITATION (LOW FREQUENCY) To find the limiting current Irms, we divide Vrms by the impedance at the desired frequency. (3) I rms = V rms ⁄ Z 2 X + ESR 2 1. Hermetic Axial (150D, CSR13): where X is 1/Cw + Lw (w = 2πf) Since inductance of a solid tantalum capacitor is usually in the nanohenry range, the Lw factor becomes important only when the frequency is higher than a few megahertz. For filtering applications at 100 kHz and lower, the inductance factor will generally be ignored in the calculation. At 120 Hz, the impedance can be determined by calculation. (5) Z = Pmax. is the maximum power dissipation the capacitor can tolerate. The ESR value in the formula is the maximum ESR of the capacitor at the required frequency. This can be determined by measuring capacitors and determining a maximum value by using the mean value and adding 3 or more standard deviations. Some manufacturers specify the maximum impedance at 100 kHz or 1 MHz. Either value may be used in ripple current calculations. Power dissipation limits calculated for the most popular surface mount types of solid tantalum capacitors are: using the formula: (4) Z = P max. ⁄ ESR 2 2 2 ( 1 ⁄ 2πfC ) + ( DF ⁄ 2πfC ) = ( 1 ⁄ 2πfC ) ( 1 + DF ) At 120 Hz, DF2 is relatively small compared with 1 and the formula can be simplified to: (6) Z = 1 ⁄ 2πfC CASE SIZE MAXIMUM POWER AT + 25 °C (W) A B C D 0.115 0.145 0.185 0.225 2. Dipped Tantalum (199D, 299D): CASE SIZE MAXIMUM POWER AT + 25 °C (W) A B C D E F 199D 299D 0.080 0.090 0.100 0.120 0.140 0.180 0.140 0.160 0.180 0.210 0.240 0.270 3. Molded Case Chip (293D): More generally, DF values of less than 10 % will not affect the final result by more than 1 %. It is important to use the lowest value for C, including the capacitance tolerance. At 120 Hz, the formula can be simplified to: (7) I rms = 0.266 × CV www.vishay.com 8 As a general guideline, it is also worth mentioning that rectangular pellets for large case size ratings have lower ESR than cylindrical ones. Since cylindrical pellets are widely used in leaded capacitors and rectangular pellets for surface mount chips, it is safe to assume that a tantalum chip will have the same or lower ESR than the same capacitance/ voltage capacitor in a leaded package. For technical questions, contact: tantalum@vishay.com Document Number: 40057 Revision: 26-Nov-07 Application Notes AC Ripple Current Calculations ESR SCREENING RIPPLE CURRENT/VOLTAGE CALCULATIONS EXAMPLE For parallel operation, the ESR spread can be minimized by screening. This reduces the risk of excess ripple current exposure to any one of the capacitors. As an example, we will determine the ripple voltage and power dissipation capability for a 1 µF, ± 20 % tolerance, 35 V, dipped tantalum capacitor. Some equipment will only measure impedance. An impedance limit can be caluclated to insure that the ESR stays in the required range. Use the formula: (10) Z max. = 2 Xc ⁄ ESR Vishay Sprague At 120 Hz: V rms = R V ⁄ 2 2 = 12.37 V 2 I rms = V rms ⁄ Z Xc = 1 ⁄ Cω = 12.37 × 2 × 3.14 × 120 × 0.8 × 10 Impedance can be measured using an impedance meter and a fixture that is appropriate for the task. With the most sophisticated fixtures, several capacitors may be tested at the same time, reducing the test cycle time. –6 = 0.007 A If we used I rms = P max. ⁄ ESR With ESR = DF ⁄ 2πfC = 04 ⁄ 2 × 3.14 × 120 × 0.8 × 10 CORRECTIVE FACTORS The calculations for high frequency ripple current are shown in formula (9) for a sinusoidal waveform and an ambient temperature of + 25 °C. If the waveform is not sinusoidal, the ripple current limitations may differ. Generally speaking, the ripple current limit calculated by formula (9) can be divided by the duty cycle of the signal. If the temperature is higher than + 25 °C, the ripple current limit should also be multiplied by the factors shown: I rms = MULTIPLYING FACTOR + 55 °C 0.9 + 85 °C 0.8 + 125 °C 0.4 0.080 ⁄ 66 = = 66 Ω 0.035 A At 120 Hz, the voltage is the limiting factor. At 100 kHz: I rms = P max. ⁄ ESR At 100 kHz, the typical ESR for a 1 µF/35 V tantalum is: ESR = TEMPERATURE °C P max. ⁄ ESR = –6 1.5 Ω ( Z = 3 Ω ) I rms = 0.080 ⁄ 1.5 = 0.231 A If we now look at the maximum ripple voltage, the above limitation translates into: V rms = Z × I rms = 3 × 0.231 = 0.69 V At 100 kHz, the power dissipation is the limiting factor. TYPICAL CURVES OF IMPEDANCE AND ESR VS. FREQUENCY 100 IMPEDANCE ESR 10 1 µF, 35 V, A CASE 1 4.7 µF, 35 V, C CASE 0.1 100 1K 10K 100K 1M 10M FREQUENCY Document Number: 40057 Revision: 26-Nov-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 9 Application Notes Vishay Sprague AC Ripple Current Calculations CONCLUSIONS The industry is moving towards smaller and smaller power supplies and DC/DC converters operating at higher frequencies. The three factors shown become more and more important in capacitor selection. 1. Higher Switching Frequencies: The switching frequency of power supplies has increased from the 10 kHz range a decade ago to the 100 kHz range and up today. The ESR of solid tantalum capacitors is either the same or lower at higher frequencies and impedance is at a minimum in the 100 kHz to megahertz range. Higher switching frequencies and the need for smaller sizes will increase the use of solid tantalum capacitors. www.vishay.com 10 2. Surface Mount Technology: The application of surface mount technology not only reduces the size of power supplies and converters but also uses the substrate on which the components are mounted to dissipate some of the heat generated by the switching elements. Solid tantalum chip capacitors are well suited for this application. They have superior operating characteristics, do not leak electrolyte and are compatible with common automated surface assembly equipment. 3. Tighter High Frequency Parameters: The reduction of the maximum ESR of a solid tantalum capacitor may produce tradeoffs in size or DC characteristics. Rather than looking at lower ESR in terms of process average, it may be advisable to try to reduce ESR variation, producing a lower maximum ESR with a tighter distribution. This improvement may be achieved by using statistical process control, an approach already being implemented at Vishay Sprague Solid Tantalum manufacturing facilities. For technical questions, contact: tantalum@vishay.com Document Number: 40057 Revision: 26-Nov-07 VISHAY SPRAGUE Leaded Tantalum Capacitors Technical Note Mounting for Through-Hole Components General All through-hole or leaded styles fall into two general classes. The first is provided with leads extending from opposite ends of the body, generally along the principle axis of the body (“axial leads”). The second is provided with parallel leads extending from one side or face of the body (“radial leads”). With both type, mounting points are normally provided by the leads themselves. Axial leads may be used for point-to-point wiring, but usually, the wires are bent at 90° from the capacitor axis for insertion through printed circuit (PC) boards. Axial capacitors supplied on reels for machine insertion will withstand the mechanical stresses of bending and inserting. The Vishay axial series may be supplied on reels to feed such machines. Radial leads are intended to plug directly into holes of PC boards. Auto-insertion machines will insert compatible radial capacitor designs, and most Vishay capacitors may be supplied in appropriate reeled forms. With either axial or radial types, attention should be paid to treatment of the capacitors during mounting and afterward under service conditions. Difficulty during mounting usuall y arises from lead damage or from overheating. The hand soldering technique or more often, wave-soldering machines can cause overheating. The internal cathode connection on most solid tantalum through-hole series is made between solder and a silver-pigmented paint. If too much heat is applied, this solder may reflow and degrade the silver-solder interface or cause a direct short circuit. Document Number: 40108 Revision: 27-Nov-07 Lead Forming While we will provide some general guidelines for bending leads, more specific details are outlined in J-STD-001. The positive or anode lead bend must be a minimum of 0.050" from the case or from the external weld connection. If the part has a hermetic (glass-to-metal) seal, do not bend, cut, or disturb the tube between the weld and the glass seal. The cathode lead bend must be a minimum of 0.050" from the case. Solder Heat Test All through-hole capacitors will pass the Resistance to Soldering Heat Test of MIL-STD-202, Method 210, Condition B. This test dips each lead-wire into molten solder at + 260 °C for 10 s while the capacitor body is held vertically above the solder. Vishay capacitors will pass this test when the depth of immersion brings the capacitor body (or closest external solder joint, if it is closer as in some hermetic styles) to a minimum distance of 0.100" from the solder surface. This demonstration of resistance to solder heat is in accordance with what is believed to be the industry standard. More severe treatment must be considered reflective of an improper soldering process. For technical questions, contact: tantalum@vishay.com www.vishay.com 11 TECH NOTE Vishay’s hermetically-sealed series has an internal space into which molten cathode solder may run, depriving the cathode connection and possibly flowing across the terminals to short circuit the capacitor from the inside. It is also possible to remelt or reflow the solder which bonds the rim of the glass-metal seal, causing loss of hermeticity and possibly a short circuit. Finally, solder at the exit point of the positive wire may be re-melted withsimilar effect. This solder however, is a high-temperature alloy, and it is much less likely to be melted. Redipping of leadwires is practiced by some users, introducing another hazard of re-melting this solder. Vishay recommends that redipping or hot solder dipping of any tantalum capacitor be performed by our factories under controlled conditions. Molded series have only one site of solder, the internal cathode connection. The rate of heat transfer through the plastic is lower than through the metal can of our hermetic styles. However the opportunity for temperature transfer or conduction along the negative lead-wire to re-melt this solder is very similar. There is little internal void within molded cased capacitors, so re-melted solder tends to remain in its original location and solidify when heat is removed. Short circuiting is very unlikely, but reliability of the internal connection may be compromised by leaching of silver from the paint into the molten solder. The latter effect degrades the cathode connection in hermetic parts as well. Technical Note Vishay Sprague Mounting for Through-Hole Components Solder Profile Shown below is a recommended solder wave profile for both axial and radial through-hole solid tantalum capacitors. LEADED SOLDER WAVE PROFILE MAX. PEAK TEMPERATURE FOR LEAD (Pb)-FREE SOLDERING: 260 °C 265 TIME AT PEAK ~ 4 s BOTTOM SIDE TEMPERATURE PROFILE 260 °C MAX. TEMPERATURE (°C) 245 225 205 TOP SIDE TEMPERATURE PROFILE 150 °C 185 165 145 125 105 85 65 45 25 0 1 2 3 4 5 6 TECH NOTE TIME (MINUTES) www.vishay.com 12 For technical questions, contact: tantalum@vishay.com Document Number: 40108 Revision: 27-Nov-07 Total Quality Commitment Vishay Sprague “We are dedicated to partnership with our customers... assuring continuously improved quality of the products and services we offer...” About the manufacture of tantalum capacitors at Vishay ... Attention to customer requirements-to your requirements keeps us on the leading edge of the quality revolution. We maintain total quality commitments throughout our operations. The scope of our Quality System encompasses: 1. Product and Materials Development 2. Process Control 3. Training 4. Outgoing Quality Improvement 5. Customer Partnerships 6. Ship-To-Stock Programs. 7. Our Quality System is Registered to ISO/QS 9000 PRODUCT AND MATERIALS DEVELOPMENT The work in our research and development facilities is focused on new materials and designs. Our scientists and engineers are recognized for their experience in this technology. Vishay Sprague, a pioneer in the field of tantalum capacitors, has introduced many important advances over the years. The collection of quality data and reporting of outgoing quality in PPM is not new to Vishay Sprague. In fact, Vishay Sprague provided leadership for the committee developing the EIA Standard for PPM measurement. And long before reporting outgoing quality in "Parts Per Million" was fashionable, Vishay Sprague had defined a program, was collecting data and reporting internally to assure quality improvement. PPM performance, by product, is calculated by Quality Assurance from end-of-the-line electrical performance data. These data include all variations, whether minor or catastrophic, from internal standards that are stricter than those used by our customers. The result is that our customers' measurement of as-received quality in PPM is always more favorable than our own measurement. Today, not all suppliers are using a standard method of PPM calculation. Consequently, when comparing reported PPM levels, it is essential that the method of calculation be understood. For example, calculations that include only catastrophic failures may produce very low reported PPM levels. CUSTOMER PARTNERSHIPS SUPPLIER PARTNERSHIPS We are continuously working with suppliers to assure a thorough understanding of our quality requirements and the use of statistical methods as a tool for process control. We expect our suppliers to be dedicated to the improvement of quality of our incoming materials, taking rigorous action to investigate and correct non-conformance whenever required. Our suppliers are considered extensions of our tantalum processes. PROCESS CONTROL Vishay ships millions of tantalum capacitors each month for aerospace and defense electronics, for computers and communications as well as for a virtually unlimited range of high-performance military, industrial and commercial equipment. We are dedicated to defect prevention in all aspects of design and manufacturing. Rigorous action is taken to investigate the root cause of non-conformances and/or variation and to correct such situations. Vishay is committed to the use of statistical techniques to reduce variation, independent of specification limit. This is one of the tools used to improve performance. We perform a thorough analysis of critical process elements using statistical methods at key points. More and more process steps are being automated to assure consistency in manufacturing and conformance to design specifications. TRAINING A disciplined procedures approach is an essential part of our quality improvement program. This requires a commitment to provide all personnel with the skills and tools necessary to produce quality at the source. Employees are trained in company philosophy, statistical process control, capability studies, application of procedures and equipment operation. Our training includes the analysis of statistical data from our processes to help us understand and control variations. As we train our operators in SPC and automate our processes, the rate of quality improvement accelerates accordingly. Document Number: 40059 Revision: 23-May-05 PARTS PER MILLION (PPM) PROGRAMS We are currently involved with many major Ship-to-Stock programs. These programs rely on our history of providing materials that meet customer quality expectations, are delivered on time and at competitive prices. This history, plus our proven dedication to continuous quality improvement and the use of statistical techniques to identify and reduce variation in our processes, provides customer confidence to eliminate incoming inspection, thereby reducing costs. Our partnership also extends to in-depth applications engineering support. Our engineers work with customers to review their designs and in the selection of the most appropriate Vishay Sprague tantalum capacitors. SHIP-TO-STOCK PROGRAMS Vishay Sprague provides a program for those customers who may not have identified their own Ship-to-Stock program. This program may be modified to suit specific needs. QUARTERLY PPM REPORTS These reports express outgoing quality of each product type purchased and may be used for monitoring quality improvement. SHIPPING CONTAINER ID We identify each container to assure that material proceeds directly to your stockroom and is not inspected when received. Vishay Sprague is responsible for its quality. VISHAY SPRAGUE SHIP TO STOCK INSP. BY DATE For technical questions, contact: wettants@vishay.com www.vishay.com 13 Quick Reference Guide Vishay Sprague SOLID TANTALUM CAPACITORS HERMETIC SEAL, METAL CASE SOLID TANTALUM LEADED CAPACITORS PICTORIAL MODEL CASE CODES DESCRIPTION PAGE Solid Tantalum Capacitor - Solid-Electrolyte TANTALEX®: 150D A, B, R, S Axial lead, hermetically sealed, high performance, high capacitance, low DCL, lLow dissipation factor. Excellent operating stability/reliability. 18 Supplied with plastic film insulation. Terminals are solid, tinned nickel wire leads. Commercial, industrial and military applications. Solid Tantalum Capacitor - Solid-Electrolyte TANTALEX®: 152D A, B, R, S Axial lead, hermetically sealed, extended capacitance, small size, low leakage current, low dissipation factor, Exceptional operating stability. Proven reliability in a wide variety of high performance commercial, industrial and military applications. 27 Solid Tantalum Capacitor - Solid-Electrolyte TANTALEX®: 550D R, S Axial lead, hermetically sealed, small size, long life. Designed for power supply filtering applications at above 100 kHz. Extremely low equivalent series resistance with the capability to handle high ripple currents in switching regulators and high frequency power supplies. 31 Solid Tantalum Capacitor - Solid-Electrolyte TANTALEX®: MIL-PRF-39003 Axial lead, tubular, hermetically sealed. CSR13 M39003/01 CSR21 M39003/09 CSR23 M39003/03 A, B, C, D C, D A, B, C, D Capacitors are qualified to MIL-PRF-39003 Exponential and Weibull distribution. - Capacitors are furnished to the requirements of the military specification, including marking, testing and inspection. 39 Also, MIL-PRF-39003 establishes failure rates (expressed in percent per 1000 h) based on exponential and Weibull distribution. Exponential failure rates are identified as levels M, P, R and S. Weibull failure rates are B, C and D. Levels M, P, R and S are inactive for new designs. CECC30201 CTS1 A, B, C, D CTS13 749DX www.vishay.com 14 The CTS1, CTS13, and 749DX series are qualified to the European standard CECC30201. These are hermetically sealed, metal case, axial leaded capacitors with long life and high performance. They have high capacitance, with low DF (dissipation factor), and low DCL (DC Leakage). The CTS1, CTS13, and 749DX have excellent operating stability and reliability. All units are supplied with plastic film isolation. The standard terminations are tin/lead plated nickel wire, but 100 % tin (RoHS compliant) terminations are available. For technical questions, contact: tantalum@vishay.com 54 Document Number: 40037 Revision: 12-Feb-08 Quick Reference Guide Vishay Sprague SOLID TANTALUM CAPACITORS NON-HERMETIC SEAL, MOLDED CASE AND RESIN COATED SOLID TANTALUM LEADED CAPACITORS PICTORIAL MODEL CASE CODES DESCRIPTION PAGE Solid Tantalum Capacitor - Solid-Electrolyte TANTALEX®: 173D U, V, W, X, Y Axial lead, miniature, molded case, precision molded in gold colored, flame retardant, thermosetting epoxy resin. Units are laser marked for improved legibility. The tapered end of the case provides easy identification of the positive terminal. Tape and reel 98 Solid Tantalum Capacitor - Solid-Electrolyte TANTALEX®: 199D A, B, C, D, E, F Radial lead, resin-coated, miniature, rugged and reliable. High performance, economical, low leakage current and dissipation factor. Two lead styles. Tape and reel packaging. Suitable for a broad range of commercial and industrial equipment applications. 111 Solid Tantalum Capacitor - Solid-Electrolyte TANTALEX®: 299D Tripole®, triple lead, resin-coated - conformal coating, miniature, high performance. The anole lead is in the center while both outside leads are cathode leads. The three-lead design makes backwards insertion impossible. Tape and reel packaging per EIA-468. 117 A, B, C, D The 489D and 499D are solid tantalum resin coated radial leaded capacitors built to conform to the European standards for ratings and case sizes. They are available in many ratings, sizes and lead configurations. They are the economical choice for a variety of applications, with low DF (disspation factor) and low DCL (DC Leakage). The units are laser marked for improved marking legibility. Standard terminations are tin/lead plated, but they are now also available with 100 % tin (RoHS compliant) terminations. Tape and reel packaging is available. 123 790D A, B, C, D Solid Tantalum Capacitor - precisely molded with a flame retardant expoxy resin coating. Four case sizes with stand-off leads. Low leakage current, low impedance and extended value ranges available 104 ETPW 1A, 1B, 2C, 2D, 2E, 3F, 3G, 4H, 5J, 5K, 5L, 6M, 6N, 6P, 6R Solid Tantalum Capacitor - resin coated with flame retardant encapsulation, practically without expoxy run down. Radial lead. Improved humidity class and low leakage current. Very high CV product, low failure rate and high operational stability. 131 1, 2, 3, 4, 5, 6 Solid Tantalum Capacitor - resin coated with flame retardant encapsulation, practically without expoxy run down. Radial lead. Improved humidity class and low leakage current. Very high CV product, low failure rate and high operational stability. 138 489D 499D ETQW Document Number: 40037 Revision: 12-Feb-08 A, B, C, D, E, F For technical questions, contact: tantalum@vishay.com www.vishay.com 15 Vishay Sprague www.vishay.com 16 Contents 150D ............................... 18 152D ............................... 27 550D .............................. 31 Metal Case M39003/01/03/09 MIL-PRF-39003 ............. 39 CTS1, CTS13, 749DX CECC30201 ................... 54 150D Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors Hermetically-Sealed, Axial-Lead FEATURES • Terminations: Tin/lead (SnPb), 100 % Tin (RoHS compliant) Available • These high performance, hermetically-sealed RoHS* TANTALEX® capacitors have set the standard for COMPLIANT solid-electrolyte tantalum capacitors for more than three decades. • High capacitance, low DCL, low dissipation factor and exceptional operating stability. • Performance and reliability have been proven in commercial, industrial and military applications. • Available in four case codes and capacitors and are supplied with plastic-film insulation. • Terminals are solid, tinned nickel wire leads. • The Military equivalent to the 150D is the CSR13 which is qualified to MIL-C-39003/01. PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 °C to + 85 °C (To + 125 °C with voltage derating) Capacitance Tolerance: At 120 Hz, + 25 °C. ± 20 %, ± 10 % standard. ± 5 % available as special. Dissipation Factor: At 120 Hz, + 25 °C. Dissipation factor, as determined from the expression 2πfRC, shall not exceed the values listed in the Standard Ratings Tables. DC Leakage Current (DCL Max.): At + 25 °C: Leakage current shall not exceed the values listed in the Standard Ratings Tables. At + 85 °C: Leakage current shall not exceed 10 times the values listed in the Standard Ratings Tables. At +125 °C: Leakage shall not exceed 15 times the values listed in the Standard Ratings Tables. Life Test: Capacitors shall withstand rated DC voltage applied at + 85 °C for 2000 h or derated DC voltage applied at + 125 °C for 1000 h Following the life test: 1. DCL shall not exceed 125 % of the initial requirement 2. Dissipation Factor shall meet the initial requirement 3. Change in capacitance shall not exceed ± 5 % DIMENSIONS in inches [millimeters] 1.500 ± 0.250 [38.10 ± 6.35] 1.500 ± 0.250 [38.10 ± 6.35] D DIA. L + - 0.047 [1.19] MAX. 0.125 [3.18] MAX. SOLID TINNED NICKEL LEADS J MAX.. WITH INSULATING SLEEVE (1) CASE CODE A B R S D L 0.135 ± 0.016 [3.43 ± 0.41] 0.185 ± 0.016 [4.70 ± 0.41] 0.289 ± 0.016 [7.34 ± 0.41] 0.351 ± 0.016 [8.92 ± 0.41] 0.286 ± 0.031 [7.26 ± 0.79] 0.474 ± 0.031 [12.04 ± 0.79] 0.686 ± 0.031 [17.42 ± 0.79] 0.786 ± 0.031 [19.96 ± 0.79] LEAD SIZE J (MAXIMUM) 0.422 [10.720] 0.610 [15.490] 0.822 [20.880] 0.922 [23.420] AWG NO. 24 24 22 22 NOMINAL DIAMETER 0.020 [0.51] 0.020 [0.51] 0.025 [0.64] 0.025 [0.64] Note: (1) When a shrink-fitted insulation is used, it shall lap over the ends of the capacitor body * Pb containing terminations are not RoHs compliant, exemptions may apply www.vishay.com 18 For technical questions, contact: tantalum@vishay.com Document Number: 40015 Revision: 16-Jan-08 150D Solid-Electrolyte TANTALEX® Capacitors Hermetically-Sealed, Axial-Lead Vishay Sprague ORDERING INFORMATION 150D MODEL 224 CAPACITANCE This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. X0 CAPACITANCE TOLERANCE X0 = ± 20 % X9 = ± 10 % *X5 = ± 5 % *Special Order 006 DC VOLTAGE RATING A CASE CODE 2 STYLE NUMBER T PACKAGING E3 ROHS COMPLIANT This is expressed in volts. To complete the three-digit block, zeros precede the voltage rating. See Ratings and Case Codes Table. 0 = No Sleeve 2 = Insulated sleeve B = Bulk T = Tape and Reel E3 = 100 % Tin termination (RoHS compliant) Blank = SnPb termination STANDARD RATINGS CAPACITANCE (µF) 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 120.0 150.0 180.0 220.0 270.0 330.0 Document Number: 40015 Revision: 16-Jan-08 MAX. DCL AT + 25 °C (µA) 6 WVDC AT + 85 °C, SURGE = 8 V . . . 4 WVDC AT + 125 °C, SURGE = 5 V A 150D224X0006A2 150D224X9006A2 0.5 A 150D274X9006A2 0.5 A 150D334X0006A2 150D334X9006A2 0.5 A 150D394X9006A2 0.5 A 150D474X0006A2 150D474X9006A2 0.5 A 150D564X9006A2 0.5 A 150D684X0006A2 150D684X9006A2 0.5 A 150D824X9006A2 0.5 A 150D105X0006A2 150D105X9006A2 0.5 A 150D125X9006A2 0.5 A 150D155X0006A2 150D155X9006A2 0.5 A 150D185X9006A2 0.5 A 150D225X0006A2 150D225X9006A2 0.5 A 150D275X9006A2 0.5 A 150D335X0006A2 150D335X9006A2 0.5 A 150D395X9006A2 0.5 A 150D475X0006A2 150D475X9006A2 0.5 A 150D565X9006A2 0.5 A 150D685X0006A2 150D685X9006A2 0.5 B 150D825X9006B2 0.5 B 150D106X0006B2 150D106X9006B2 0.5 B 150D126X9006B2 0.5 B 150D156X0006B2 150D156X9006B2 1.0 B 150D186X9006B2 1.0 B 150D226X0006B2 150D226X9006B2 1.0 B 150D276X9006B2 1.0 B 150D336X0006B2 150D336X9006B2 1.0 B 150D396X9006B2 1.0 B 150D476X0006B2 150D476X9006B2 2.0 B 150D566X9006B2 2.0 R 150D686X0006R2 150D686X9006R2 3.0 R 150D826X9006R2 3.0 R 150D107X0006R2 150D107X9006R2 3.0 R 150D127X0006R2 150D127X9006R2 3.0 R 150D157X0006R2 150D157X9006R2 6.0 R 150D187X0006R2 150D187X9006R2 6.0 S 150D227X0006S2 150D227X9006S2 6.0 S 150D277X0006S2 150D277X9006S2 6.0 S 150D337X0006S2 150D337X9006S2 10.0 CASE CODE PART NUMBER CAP. TOL. ± 20 % PART NUMBER CAP. TOL. ± 10 % For technical questions, contact: tantalum@vishay.com MAX. DF AT + 25 °C 120 Hz (%) 2 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 www.vishay.com 19 150D Solid-Electrolyte TANTALEX® Capacitors Hermetically-Sealed, Axial-Lead Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 120.0 150.0 180.0 220.0 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 Max. DCL AT+ 25 °C (µA) 10 WVDC AT + 85 °C, SURGE = 13 V . . . 7 WVDC AT + 125 °C, SURGE = 9 V A 150D224X0010A2 150D224X9010A2 0.5 A 150D274X9010A2 0.5 A 150D334X0010A2 150D334X9010A2 0.5 A 150D394X9010A2 0.5 A 150D474X0010A2 150D474X9010A2 0.5 A 150D564X9010A2 0.5 A 150D684X0010A2 150D684X9010A2 0.5 A 150D824X9010A2 0.5 A 150D105X0010A2 150D105X9010A2 0.5 A 150D125X9010A2 0.5 A 150D155X0010A2 150D155X9010A2 0.5 A 150D185X9010A2 0.5 A 150D225X0010A2 150D225X9010A2 0.5 A 150D275X9010A2 0.5 A 150D335X0010A2 150D335X9010A2 0.5 A 150D395X9010A2 0.5 A 150D475X0010A2 150D475X9010A2 0.5 B 150D565X9010B2 0.5 B 150D685X0010B2 150D685X9010B2 1.0 B 150D825X9010B2 1.0 B 150D106X0010B2 150D106X9010B2 1.0 B 150D126X9010B2 1.0 B 150D156X0010B2 150D156X9010B2 1.0 B 150D186X9010B2 1.0 B 150D226X0010B2 150D226X9010B2 2.0 B 150D276X9010B2 2.0 B 150D336X0010B2 150D336X9010B2 2.0 B 150D396X9010B2 2.0 R 150D476X0010R2 150D476X9010R2 3.0 R 150D566X9010R2 3.0 R 150D686X0010R2 150D686X9010R2 3.0 R 150D826X9010R2 3.0 R 150D107X0010R2 150D107X9010R2 6.0 R 150D127X0010R2 150D127X9010R2 6.0 S 150D157X0010S2 150D157X9010S2 10.0 S 150D187X0010S2 150D187X9010S2 10.0 S 150D227X0010S2 150D227X9010S2 10.0 15 WVDC AT + 85 °C, SURGE = 20 V . . . 10 WVDC AT + 125 °C, SURGE = 12 V A 150D224X0015A2 150D224X9015A2 0.5 A 150D274X9015A2 0.5 A 150D334X0015A2 150D334X9015A2 0.5 A 150D394X9015A2 0.5 A 150D474X0015A2 150D474X9015A2 0.5 A 150D564X9015A2 0.5 A 150D684X0015A2 150D684X9015A2 0.5 A 150D824X9015A2 0.5 A 150D105X0015A2 150D105X9015A2 0.5 A 150D125X9015A2 0.5 A 150D155X0015A2 150D155X9015A2 0.5 A 150D185X9015A2 0.5 A 150D225X0015A2 150D225X9015A2 0.5 A 150D275X9015A2 0.5 A 150D335X0015A2 150D335X9015A2 0.5 B 150D395X9015B2 0.5 B 150D475X0015B2 150D475X9015B2 1.0 CASE CODE PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % Max. DF AT + 25 °C 120 Hz (%) 2 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 8 2 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 Note: Insert capacitance tolerance code “X5” for ± 5 % units (special order) (1) www.vishay.com 20 For technical questions, contact: tantalum@vishay.com Document Number: 40015 Revision: 16-Jan-08 150D Solid-Electrolyte TANTALEX® Capacitors Hermetically-Sealed, Axial-Lead Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 120.0 150.0 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 Max. DCL AT + 25 °C (µA) 15 WVDC AT + 85 °C, SURGE = 20 V . . . 10 WVDC AT + 125 °C, SURGE = 12 V B 150D565X9015B2 1.0 B 150D685X0015B2 150D685X9015B2 1.0 B 150D825X9015B2 1.0 B 150D106X0015B2 150D106X9015B2 1.0 B 150D126X9015B2 1.0 B 150D156X0015B2 150D156X9015B2 2.0 B 150D186X9015B2 2.0 B 150D226X0015B2 150D226X9015B2 3.0 R 150D276X9015R2 3.0 R 150D336X0015R2 150D336X9015R2 3.0 R 150D396X9015R2 3.0 R 150D476X0015R2 150D476X9015R2 6.0 R 150D566X9015R2 6.0 R 150D686X0015R2 150D686X9015R2 6.0 S 150D826X9015S2 6.0 S 150D107X0015S2 150D107X9015S2 6.0 S 150D127X0015S2 150D127X9015S2 6.0 S 150D157X0015S2 150D157X9015S2 10.0 20 WVDC AT + 85 °C, SURGE = 26 V . . . 13 WVDC AT + 125 °C, SURGE = 16 V A 150D273X9020A2 0.1 A 150D333X0020A2 150D333X9020A2 0.1 A 150D393X9020A2 0.1 A 150D473X0020A2 150D473X9020A2 0.1 A 150D563X9020A2 0.1 A 150D683X0020A2 150D683X9020A2 0.1 A 150D823X9020A2 0.1 A 150D104X0020A2 150D104X9020A2 0.5 A 150D124X9020A2 0.5 A 150D154X0020A2 150D154X9020A2 0.5 A 150D184X9020A2 0.5 A 150D224X0020A2 150D224X9020A2 0.5 A 150D274X9020A2 0.5 A 150D334X0020A2 150D334X9020A2 0.5 A 150D394X9020A2 0.5 A 150D474X0020A2 150D474X9020A2 0.5 A 150D564X9020A2 0.5 A 150D684X0020A2 150D684X9020A2 0.5 A 150D824X9020A2 0.5 A 150D105X0020A2 150D105X9020A2 0.5 A 150D125X9020A2 0.5 A 150D155X0020A2 150D155X9020A2 0.5 A 150D185X9020A2 0.5 A 150D225X0020A2 150D225X9020A2 0.5 B 150D275X9020B2 0.5 B 150D335X0020B2 150D335X9020B2 0.5 B 150D395X9020B2 1.0 B 150D475X0020B2 150D475X9020B2 1.0 B 150D565X9020B2 1.0 B 150D685X0020B2 150D685X9020B2 1.0 B 150D825X9020B2 1.0 B 150D106X0020B2 150D106X9020B2 1.0 B 150D126X9020B2 1.0 B 150D156X0020B2 150D156X9020B2 2.0 CASE CODE PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % Max. DF AT + 25 °C 120 Hz (%) 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 4 6 6 6 6 6 Note: (1) Insert capacitance tolerance code “X5” for ± 5 % units (special order) Document Number: 40015 Revision: 16-Jan-08 For technical questions, contact: tantalum@vishay.com www.vishay.com 21 150D Solid-Electrolyte TANTALEX® Capacitors Hermetically-Sealed, Axial-Lead Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 Max. DCL AT + 25 °C (µA) 20 WVDC AT + 85 °C, SURGE = 26 V . . . 13 WVDC AT + 125 °C, SURGE = 16 V R 150D186X9020R2 3.0 R 150D226X0020R2 150D226X9020R2 3.0 R 150D276X9020R2 3.0 R 150D336X0020R2 150D336X9020R2 3.0 R 150D396X9020R2 3.0 R 150D476X0020R2 150D476X9020R2 6.0 S 150D566X9020S2 6.0 S 150D686X0020S2 150D686X9020S2 6.0 S 150D826X9020S2 6.0 S 150D107X0020S2 150D107X9020S2 10.0 35 WVDC AT + 85 °C, SURGE = 46 V . . . 23 WVDC AT + 125 °C, SURGE = 28 V A 150D273X9035A2 0.1 A 150D333X0035A2 150D333X9035A2 0.1 A 150D393X9035A2 0.1 A 150D473X0035A2 150D473X9035A2 0.1 A 150D563X9035A2 0.1 A 150D683X0035A2 150D683X9035A2 0.1 A 150D823X9035A2 0.1 A 150D104X0035A2 150D104X9035A2 0.5 A 150D124X9035A2 0.5 A 150D154X0035A2 150D154X9035A2 0.5 A 150D184X9035A2 0.5 A 150D224X0035A2 150D224X9035A2 0.5 A 150D274X9035A2 0.5 A 150D334X0035A2 150D334X9035A2 0.5 A 150D394X9035A2 0.5 A 150D474X0035A2 150D474X9035A2 0.5 A 150D564X9035A2 0.5 A 150D684X0035A2 150D684X9035A2 0.5 A 150D824X9035A2 0.5 A 150D105X0035A2 150D105X9035A2 0.5 B 150D125X9035B2 0.5 B 150D155X0035B2 150D155X9035B2 0.5 B 150D185X9035B2 0.5 B 150D225X0035B2 150D225X9035B2 1.0 B 150D275X9035B2 1.0 B 150D335X0035B2 150D335X9035B2 1.0 B 150D395X9035B2 1.0 B 150D475X0035B2 150D475X9035B2 1.0 B 150D565X9035B2 1.0 B 150D685X0035B2 150D685X9035B2 2.0 R 150D825X9035R2 3.0 R 150D106X0035R2 150D106X9035R2 3.0 R 150D126X9035R2 3.0 R 150D156X0035R2 150D156X9035R2 3.0 R 150D186X9035R2 3.0 R 150D226X0035R2 150D226X9035R2 6.0 S 150D276X9035S2 6.0 S 150D336X0035S2 150D336X9035S2 6.0 S 150D396X9035S2 6.0 S 150D476X0035S2 150D476X9035S2 10.0 CASE CODE PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % Max. DF AT + 25 °C 120 Hz (%) 6 6 6 6 6 6 6 6 6 6 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 Note: Insert capacitance tolerance code “X5” for ± 5 % units (special order) (1) www.vishay.com 22 For technical questions, contact: tantalum@vishay.com Document Number: 40015 Revision: 16-Jan-08 150D Solid-Electrolyte TANTALEX® Capacitors Hermetically-Sealed, Axial-Lead Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 0.1 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 1.0 2.2 4.7 5.6 6.8 8.2 10 12 15 18 22 CASE CODE PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % Max. DCL AT + 25 °C 50 WVDC AT + 85 °C, SURGE = 65 V . . . 33 WVDC AT + 125 °C, SURGE = 40 V A 150D563X9050A2 0.1 A 150D683X0050A2 150D683X9050A2 0.1 A 150D823X9050A2 0.1 A 150D104X0050A2 150D104X9050A2 0.5 A 150D124X9050A2 0.5 A 150D154X0050A2 150D154X9050A2 0.5 A 150D184X9050A2 0.5 A 150D224X0050A2 150D224X9050A2 0.5 A 150D274X9050A2 0.5 A 150D334X0050A2 150D334X9050A2 0.5 A 150D394X9050A2 0.5 A 150D474X0050A2 150D474X9050A2 0.5 A 150D564X9050A2 0.5 A 150D684X0050A2 150D684X9050A2 0.5 A 150D824X9050A2 0.5 A 150D105X0050A2 150D105X9050A2 0.5 B 150D125X9050B2 0.5 B 150D155X0050B2 150D155X9050B2 0.5 B 150D185X9050B2 0.5 B 150D225X0050B2 150D225X9050B2 1.0 B 150D275X9050B2 1.0 B 150D335X0050B2 150D335X9050B2 2.0 B 150D395X9050B2 2.0 B 150D475X0050B2 150D475X9050B2 3.0 R 150D565X9050R2 3.0 R 150D685X0050R2 150D685X9050R2 3.0 R 150D825X9050R2 3.0 R 150D106X0050R2 150D106X9050R2 3.0 R 150D126X9050R2 3.0 R 150D156X0050R2 150D156X9050R2 6.0 R 150D186X9050R2 6.0 S 150D226X0050S2 150D226X9050S2 6.0 60 WVDC AT + 85 °C, SURGE = 78 V … 40 WVDC AT +125 °C, SURGE = 49 V A 150D104X0060A2 150D104X9060A2 0.5 A 150D124X0060A2 150D124X9060A2 0.5 A 150D154X0060A2 150D154X9060A2 0.5 A 150D184X0060A2 150D184X9060A2 0.5 A 150D224X0060A2 150D224X9060A2 0.5 A 150D274X0060A2 150D274X9060A2 0.5 A 150D334X0060A2 150D334X9060A2 0.5 A 150D394X0060A2 150D394X9060A2 0.5 A 150D474X0060A2 150D474X9060A2 0.5 A 150D564X0060A2 150D564X9060A2 0.5 A 150D684X0060A2 150D684X9060A2 0.5 B 150D105X0060A2 150D105X9060A2 0.5 B 150D225X0060A2 150D225X9060A2 1.0 R 150D475X0060A2 150D475X9060A2 3.0 R 150D565X0060A2 150D565X9060A2 3.0 R 150D685X0060A2 150D685X9060A2 4.0 R 150D825X0060A2 150D825X9060A2 5.0 R 150D106X0060A2 150D106X9060A2 6.0 S 150D126X0060A2 150D126X9060A2 6.0 S 150D156X0060A2 150D156X9060A2 9.0 S 150D186X0060A2 150D186X9060A2 10.0 S 150D226X0060A2 150D226X9060A2 12.0 Max. DF AT + 25 °C 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 Note: Insert capacitance tolerance code “X5” for ± 5 % units (special order) (1) Document Number: 40015 Revision: 16-Jan-08 For technical questions, contact: tantalum@vishay.com www.vishay.com 23 150D Solid-Electrolyte TANTALEX® Capacitors Hermetically-Sealed, Axial-Lead Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 CASE CODE PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % Max. DCL AT + 25 °C (µA) 75 WVDC AT + 85 °C, SURGE = 98 V . . . 50 WVDC AT + 125 °C, SURGE = 64 V A 150D333X0075A2 150D333X9075A2 0.5 A 150D393X9075A2 0.5 A 150D473X0075A2 150D473X9075A2 0.5 A 150D563X9075A2 0.5 A 150D683X0075A2 150D683X9075A2 0.5 A 150D823X9075A2 0.5 A 150D104X0075A2 150D104X9075A2 0.5 A 150D124X9075A2 0.5 A 150D154X0075A2 150D154X9075A2 0.5 A 150D184X9075A2 0.5 A 150D224X0075A2 150D224X9075A2 0.5 A 150D274X9075A2 0.5 A 150D334X0075A2 150D334X9075A2 0.5 A 150D394X9075A2 0.5 A 150D474X0075A2 150D474X9075A2 0.5 A 150D564X9075A2 0.5 A 150D684X0075A2 150D684X9075A2 0.5 B 150D824X9075B2 0.5 B 150D105X0075B2 150D105X9075B2 0.5 B 150D125X9075B2 0.5 B 150D155X0075B2 150D155X9075B2 1.0 B 150D185X9075B2 1.0 B 150D225X0075B2 150D225X9075B2 1.0 B 150D275X9075B2 1.0 B 150D335X0075B2 150D335X9075B2 2.0 B 150D395X9075B2 2.0 R 150D475X0075R2 150D475X9075R2 4.0 R 150D565X9075R2 4.0 R 150D685X0075R2 150D685X9075R2 6.0 R 150D825X9075R2 6.0 R 150D106X0075R2 150D106X9075R2 8.0 S 150D126X9075S2 10.0 S 150D156X0075S2 150D156X9075S2 12.0 100 WVDC AT + 85 °C, SURGE = 130 V . . . 67 WVDC AT + 125 °C, SURGE = 86 V A 150D333X0100A2 150D333X9100A2 0.5 A 150D393X9100A2 0.5 A 150D473X0100A2 150D473X9100A2 0.5 A 150D563X9100A2 0.5 A 150D683X0100A2 150D683X9100A2 0.5 A 150D823X9100A2 0.5 A 150D104X0100A2 150D104X9100A2 0.5 A 150D124X9100A2 0.5 A 150D154X0100A2 150D154X9100A2 0.5 A 150D184X9100A2 0.5 A 150D224X0100A2 150D224X9100A2 0.5 A 150D274X9100A2 0.5 A 150D334X0100A2 150D334X9100A2 0.5 A 150D394X9100A2 0.5 A 150D474X0100A2 150D474X9100A2 0.5 A 150D564X9100A2 0.5 B 150D684X0100B2 150D684X9100B2 0.5 B 150D824X9100B2 0.5 Max. DF AT + 25 °C 120 Hz (%) 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 4 4 4 4 4 4 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Note: (1) Insert capacitance tolerance code “X5” for ± 5 % units (special order) www.vishay.com 24 For technical questions, contact: tantalum@vishay.com Document Number: 40015 Revision: 16-Jan-08 150D Solid-Electrolyte TANTALEX® Capacitors Hermetically-Sealed, Axial-Lead Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) CASE CODE PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % Max. DCL AT + 25 °C (µA) Max. DF AT + 25 °C 120 Hz (%) 100 WVDC AT + 85 °C, SURGE = 130 V . . . 67 WVDC AT + 125 °C, SURGE = 86 V 1.0 B 150D105X0100B2 150D105X9100B2 0.5 2 1.2 B - 150D125X9100B2 0.5 3 1.5 B 150D155X0100B2 150D155X9100B2 0.6 3 1.8 B - 150D185X9100B2 0.6 3 2.2 B 150D225X0100B2 150D225X9100B2 0.6 3 2.7 B - 150D275X9100B2 0.6 3 3.3 R 150D335X0100R2 150D335X9100R2 2.5 3 3.9 R - 150D395X9100R2 3.0 3 4.7 R 150D475X0100R2 150D475X9100R2 4.0 3 5.6 R - 150D565X9100R2 4.0 3 6.8 R 150D685X0100R2 150D685X9100R2 6.0 3 8.2 S 150D825X0100S2 150D825X9100S2 6.0 3 10 S 150D106X0100S2 150D106X9100S2 6.0 3 125 WVDC AT + 85 °C, SURGE = 140 V . . . 82 WVDC AT + 125 °C, SURGE = 94 V 0.027 A - 150D273X9125A2 1.0 2 0.033 A 150D333X0125A2 150D333X9125A2 1.0 2 0.039 A - 150D393X9125A2 1.0 2 0.047 A 150D473X0125A2 150D473X9125A2 1.0 2 0.056 A - 150D563X9125A2 1.0 2 0.068 A 150D683X0125A2 150D683X9125A2 1.0 2 0.082 A - 150D823X9125A2 1.0 2 0.10 A 150D104X0125A2 150D104X9125A2 1.0 2 0.12 A - 150D124X9125A2 1.0 2 0.15 A 150D154X0125A2 150D154X9125A2 1.0 2 0.18 A - 150D184X9125A2 1.0 2 0.22 A 150D224X0125A2 150D224X9125A2 1.0 2 0.27 A - 150D274X9125A2 1.0 2 0.33 A 150D334X0125A2 150D334X9125A2 1.0 2 0.39 A - 150D394X9125A2 1.5 2 0.47 A 150D474X0125A2 150D474X9125A2 1.5 2 0.56 B - 150D564X9125B2 1.6 2 0.68 B 150D684X0125B2 150D684X9125B2 1.8 2 0.82 B - 150D824X9125B2 2.0 2 1.0 B 150D105X0125B2 150D105X9125B2 2.0 2 1.2 B - 150D125X9125B2 2.0 3 1.5 B 150D155X0125B2 150D155X9125B2 2.0 3 1.8 B - 150D185X9125B2 2.0 3 2.2 B 150D225X0125B2 150D225X9125B2 2.0 3 Note: (1) Insert capacitance tolerance code “X5” for ± 5 % units (special order). Document Number: 40015 Revision: 16-Jan-08 For technical questions, contact: tantalum@vishay.com www.vishay.com 25 150D Solid-Electrolyte TANTALEX® Capacitors Hermetically-Sealed, Axial-Lead Vishay Sprague STANDARD REEL PACKAGING SPECIFICATIONS - MEETS EIA STANDARD RS-296 in inches [millimeters] 13.0 [330.2] “A” STANDARD REEL TAPE SPACING B 1.126 to 3.07 [28.6 to 78.0] A I. D. REEL HUB COMPONENT SPACING 1.374 to 3.626 [34.9 to 92.1] 0.031 [0.79] MAX. OFF CENTER (1. a) 0.625 ± 0.0062 DIA. [15.88 ± 1.575] THRU HOLE 0.125 [3.18] MAX. 0.250 [6.35] (3. b) LABEL (4. a) CASE CODE A B R S 0.750 [19.05] “A” SECTION “A” - “A” TYPE 150D UNITS WITH INSULATING SLEEVE D 0.135 ± 0.016 [3.43 ± 0.41] 0.185 ± 0.016 [4.70 ± 0.41] 0.289 ± 0.016 [7.34 ± 0.41] 0.351 ± 0.016 [8.92 ± 0.41] 0.031 [0.79] (3. f) LEAD SIZE L 0.286 ± 0.031 [7.26 ± 0.79] 0.474 ± 0.031 [12.04 ± 0.79] 0.686 ± 0.031 [17.42 ± 0.79] 0.786 ± 0.031 [19.96 ± 0.79] AWG NO. 24 24 22 22 NOM. DIA. 0.020 [0.51] 0.020 [0.51] 0.025 [0.64] 0.025 [0.64] BOTH SIDES (3. f) COMPONENT SPACING TAPE SPACING A 0.200 ± 0.015 [5.08 ± 0.38] 0.200 ± 0.015 [5.08 ± 0.38] 0.400 ± 0.015 [10.16 ± 0.38] 0.400 ± 0.015 [10.16 ± 0.38] B 2.500 ± 0.062 [63.5 ± 1.57] 2.500 ± 0.062 [63.5 ± 1.57] 2.875 ± 0.062 [73.03 ± 1.57] 2.875 ±0.062 [73.03 ± 1.57] UNITS PER REEL 1000 1000 500 500 STANDARD REEL PACKAGING INFORMATION 1. Component Leads: a. Component leads shall not be bent beyond 0.047" [1.19 mm] maximum from their nominal position when measured from the leading edge of the component lead at the inside tape edge and at the lead egress from the component. b. The “C” dimension shall be governed by the overall length of the reel packaged component. The distance between flanges shall be 0.125" to 0.250" [3.18 mm to 6.35 mm] greater than the overall component length. 2. Orientation: All polarized components must be oriented to one direction. The cathode lead tape shall be a color and the anode lead tape shall be white. 3. Reeling: a. Components on any reel shall not represent more than two date codes when date code identification is required. b. Component leads shall be positioned between pairs of 0.250" [6.35 mm] tape. c. The disposable reels have hubs and corrugated fibreboard flanges and core or equivalent. d. A minimum of 12.0" [304.8 mm] leader of tape shall be provided before the first and after the last component on the reel. e. 50 or 60 lb. Kraft paper must be wound between layer of components as far as necessary for component protection. Width of paper to be 0.062" to 0.250" [1.57 mm to 6.35 mm] less than the “C” dimension of the reel. Solid-Electrolyte TANTALEX® Capacitors Hermetically- Sealed, Axial-Lead. www.vishay.com 26 f. A row of components must be centered between tapes ± 0.047" [1.19 mm]. In addition, individual components may deviate from center of component row ± 0.031" [0.79 mm]. g. Staples shall not be used for splicing. Not more than 4 layers of tape shall be used in any splice area and no tape shall be offset from another by more than 0.031" [0.79 mm] non-cumulative. Tape splices shall overlap at least 6.0" [152.4 mm] for butt joints and at least 3.0" [76.2 mm] for lap joints and shall not be weaker than unspliced tape. Universal splicing clips may also be used. h. Quantity per reel shall be controlled so that tape components and cover shall not extend beyond the smallest dimension of the flange (either across flats or diameter). Once the quantity per reel for each part number has been established, future orders for that part number shall be packaged in that quantity. When order or release quantity is less than the established quantity, a standard commercial pack is to be used. i. A maximum of 0.25 % of the components per reel quantity may be missing without consecutive missing components. j. Adequate protection must be provided to prevent physical damage to both reel and components during shipment and storage. 4. Marking: Minimum reel and carton marking shall consist of the following: Customer Part Number, Purchase Order No., Quantity, Package Date, Manufacturer's Name, Electrical Value, Date Code, Vishay Sprague Part Number and Country of Origin. For technical questions, contact: tantalum@vishay.com Document Number: 40015 Revision: 16-Jan-08 152D Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors Extended Capacitance Values, Hermetically-Sealed FEATURES • Terminatons: Tin/lead (SnPb), 100 % Tin (RoHS compliant) Available • • • • • High capacitance and small size RoHS* Low leakage current and low dissipation factor COMPLIANT Exceptional operating stability Hermetically-sealed, cylindrical, metal-case The military equivalent to the 152D is the CSR23 which is qualified to MIL-C-39003/03 • Provide proven reliability in a wide variety of high performance military, industrial and commercial markets PERFORMANCE CHARACTERISTICS At + 125 °C: Leakage shall not exceed 12 times the values listed in the Standard Ratings Tables. Life Test: Capacitors shall withstand rated DC voltage applied at + 85 °C for 2000 h or derated DC voltage applied at + 125 °C for 1000 h. Following the life test: 1.DCL shall not exceed 125 % of the initial requirements. In no case need the leakage current be less than 2 µA. 2.Dissipation Factor shall meet the initial requirement 3.Change in capacitance shall not exceed ± 5 % Operating Temperature: - 55 °C to + 85 °C (To + 125 °C with voltage derating) Capacitance Tolerance: At 120 Hz, + 25 °C ± 20 % and ± 10 % standard, ± 5 % available as special Dissipation Factor: At 120 Hz, + 25 °C. Dissipation factor, as determined from the expression 2πfRC, shall not exceed the values listed in the Standard Ratings Tables DC Leakage Current (DCL Max.): At + 25 °C: Leakage current shall not exceed the values listed in the Standard Ratings Tables At + 85 °C: Leakage current shall not exceed 10 times the values listed in the Standard Ratings Tables ORDERING INFORMATION 152D MODEL 106 CAPACITANCE X0 CAPACITANCE TOLERANCE This is expressed in X0 = ± 20 % X9 = ± 10 % picofarads. The first *X5 = ± 5 % two digits are the significant figures. The *Special Order third is the number of zeros to follow. 006 DC VOLTAGE RATING AT + 85 °C This is expressed in volts. To complete the three-digit block, zeros precede the voltage rating. A 2 CASE STYLE CODE NUMBER See Ratings 2 = and Case Insulated Codes sleeve. Table. T PACKAGING T = Tape and Reel E3 ROHS COMPLIANT E3 = 100 % tin termination (RoHS compliant) Blank = SnPb termination DIMENSIONS in inches [millimeters] 1.500 ± 0.250 [38.10 ± 6.35] 1.500 ± 0.250 [38.10 ± 6.35] D DIA. L - + 0.047 [1.19] MAX. SOLID TINNED LEADS 0.125 [3.18] MAX. J MAX. . CASE CODE WITH INSULATING SLEEVE (1) D 0.135 ± 0.016 [3.43 ± 0.41] 0.185 ± 0.016 [4.70 ± 0.41] 0.289 ± 0.016 [7.34 ± 0.41] 0.351 ± 0.016 [8.92 ± 0.41] L 0.286 ± 0.031 [7.26 ± 0.79] 0.474 ± 0.031 [12.04 ± 0.79] 0.686 ± 0.031 [17.42 ± 0.79] 0.786 ± 0.031 [19.96 ± 0.79] J (MAXIMUM) A 0.422 [10.72] B 0.610 [15.49] R 0.822 [20.88] S 0.922 [23.42] Notes: (1) When a shrink-fitted insulation is used, it shall lap over the ends of the capacitor body * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 40016 Revision: 18-Jan-08 For technical questions, contact: tantalum@vishay.com LEAD SIZE AWG NO. 24 24 22 22 NOMINAL DIA. 0.020 [0.51] 0.020 [0.51] 0.025 [0.64] 0.025 [0.64] www.vishay.com 27 152D Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors Extended Capacitance Values, Hermetically-Sealed STANDARD RATINGS CAPACITANCE (µF) 10 12 15 68 82 100 330 390 470 560 680 820 1000 5.6 6.8 8.2 10 47 56 68 82 150 180 220 270 330 390 470 560 3.9 4.7 5.6 6.8 27 33 39 82 100 120 150 180 220 270 330 CASE CODE PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % Max. DCL AT+ 25 °C (µA) 6 WVDC AT + 85 °C, SURGE = 8 V . . . 4 WVDC AT + 125 °C, SURGE = 5 V A 152D106X0006A2 152D106X9006A2 1.0 A 152D126X9006A2 1.0 A 152D156X0006A2 152D156X9006A2 1.0 B 152D686X0006B2 152D686X9006B2 3.0 B 152D826X9006B2 3.0 B 152D107X0006B2 152D107X9006B2 6.0 R 152D337X0006R2 152D337X9006R2 10.0 R 152D397X9006R2 10.0 R 152D477X0006R2 152D477X9006R2 10.0 S 152D567X9006S2 20.0 S 152D687X0006S2 152D687X9006S2 20.0 S 152D827X9006S2 20.0 S 152D108X0006S2 152D108X9006S2 20.0 10 WVDC AT + 85 °C, SURGE = 13 V . . . 7 WVDC AT + 125 °C, SURGE = 9 V A 152D565X9010A2 1.0 A 152D685X0010A2 152D685X9010A2 1.0 A 152D825X9010A2 1.2 A 152D106X0010A2 152D106X9010A2 1.2 B 152D476X0010B2 152D476X9010B2 4.0 B 152D566X9010B2 5.0 B 152D686X0010B2 152D686X9010B2 6.0 B 152D826X9010B2 7.0 R 152D157X0010R2 152D157X9010R2 8.0 R 152D187X9010R2 8.0 R 152D227X0010R2 152D227X9010R2 12.0 R 152D277X9010R2 13.0 S 152D337X0010S2 152D337X9010S2 16.0 S 152D397X9010S2 16.0 S 152D477X0010S2 152D477X9010S2 16.0 S 152D567X9010S2 20.0 15 WVDC AT + 85 °C, SURGE = 20 V . . . 10 WVDC AT + 125 °C, SURGE = 12 V A 152D395X9015A2 1.0 A 152D475X0015A2 152D475X9015A2 1.0 A 152D565X9015A2 1.3 A 152D685X0015A2 152D685X9015A2 1.3 B 152D276X9015B2 3.0 B 152D336X0015B2 152D336X9015B2 5.0 B 152D396X9015B2 5.0 R 152D826X9015R2 8.0 R 152D107X0015R2 152D107X9015R2 10.0 R 152D127X9015R2 10.0 R 152D157X0015R2 152D157X9015R2 15.0 R 152D187X9015R2 15.0 S 152D227X0015S2 152D227X9015S2 20.0 S 152D277X9015S2 20.0 S 152D337X0015S2 152D337X9015S2 20.0 Max. DF AT + 25 °C 120 Hz (%) 6 6 6 6 6 6 8 8 8 10 10 10 10 4 6 6 6 6 6 6 6 8 8 8 8 8 10 10 10 4 4 4 6 6 6 6 6 8 8 8 8 8 8 8 Note: (1) Insert capacitance tolerance code “X5” for ± 5 % units (special order). www.vishay.com 28 For technical questions, contact: tantalum@vishay.com Document Number: 40016 Revision: 18-Jan-08 152D Solid-Electrolyte TANTALEX® Capacitors Extended Capacitance Values, Hermetically-Sealed Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) 2.7 3.3 3.9 4.7 18 22 27 56 68 82 100 120 150 180 220 2.2 2.7 12 15 18 56 68 82 100 1.2 1.5 1.8 8.2 10 27 33 39 47 56 68 82 100 1.2 1.5 5.6 6.8 22 27 33 39 47 CASE CODE PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % Max. DCL AT + 25 °C (µA) 20 WVDC AT + 85 °C, SURGE = 26 V . . . 13 WVDC AT + 125 °C, SURGE = 16 V A 152D275X9020A2 0.8 A 152D335X0020A2 152D335X9020A2 1.0 A 152D395X9020A2 1.2 A 152D475X0020A2 152D475X9020A2 1.2 B 152D186X9020B2 3.0 B 152D226X0020B2 152D226X9020B2 3.0 B 152D276X9020B2 4.0 R 152D566X9020R2 7.0 R 152D686X0020R2 152D686X9020R2 8.0 R 152D826X9020R2 10.0 R 152D107X0020R2 152D107X9020R2 12.0 R 152D127X9020R2 12.0 S 152D157X0020S2 152D157X9020S2 15.0 S 152D187X9020S2 15.0 S 152D227X0020S2 152D227X9020S2 15.0 30 WVDC AT + 85 °C, SURGE = 39 V . . . 20 WVDC AT + 125 °C, SURGE = 26 V A 152D225X0030A2 152D225X9030A2 1.0 A 152D275X9030A2 1.0 B 152D126X9030B2 3.0 B 152D156X0030B2 152D156X9030B2 3.0 B 152D186X9030B2 3.0 R 152D566X9030R2 7.0 R 152D686X0030R2 152D686X9030R2 7.0 S 152D826X9030S2 10.0 S 152D107X0030S2 152D107X9030S2 10.0 35 WVDC AT + 85 °C, SURGE = 46 V . . . 23 WVDC AT + 125 °C, SURGE = 28 V A 152D125X9035A2 0.6 A 152D155X0035A2 152D155X9035A2 0.8 A 152D185X9035A2 1.0 B 152D825X9035B2 3.0 B 152D106X0035B2 152D106X9035B2 3.0 R 152D276X9035R2 7.0 R 152D336X0035R2 152D336X9035R2 8.0 R 152D396X9035R2 10.0 R 152D476X0035R2 152D476X9035R2 10.0 S 152D566X9035S2 12.0 S 152D686X0035S2 152D686X9035S2 12.0 S 152D826X9035S2 30.0 S 152D107X0035S2 152D107X9035S2 30.0 50 WVDC AT + 85 °C, SURGE = 65 V . . . 33 WVDC AT + 125 °C, SURGE = 40 V A 152D125X9050A2 0.6 A 152D155X0050A2 152D155X9050A2 0.8 B 152D565X9050B2 2.5 B 152D685X0050B2 152D685X9050B2 2.5 R 152D226X0050R2 152D226X9050R2 7.0 R 152D276X9050R2 8.0 S 152D336X0050S2 152D336X9050S2 10.0 S 152D396X9050S2 10.0 S 152D476X0050S2 152D476X9050S2 10.0 60 WVDC AT + 85 °C, SURGE = 78 V . . . 39 WVDC AT + 125 °C, SURGE = 49 V R 152D226X0060R2 7 22 Note: (1) Insert capacitance tolerance code “X5” for ± 5 % units (special order). Document Number: 40016 Revision: 18-Jan-08 For technical questions, contact: tantalum@vishay.com Max. DF AT + 25 °C 120 Hz (%) 4 4 4 4 4 4 4 6 6 6 6 6 8 8 8 4 4 4 4 4 6 6 8 8 4 4 4 4 4 6 6 6 6 6 6 8 8 4 4 4 4 6 6 6 6 6 6 www.vishay.com 29 152D Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors Extended Capacitance Values, Hermetically-Sealed STANDARD REEL PACKAGING SPECIFICATIONS - MEETS EIA STANDARD RS-296 in inches [millimeters] 13.0 [330.2] “A” STANDARD REEL TAPE SPACING B 1.126 to 3.07 [28.6 to 78.0] A I. D. REEL HUB COMPONENT SPACING 1.374 to 3.626 [34.9 to 92.1] 0.031 [0.79] MAX. OFF CENTER (1. a) 0.625 ± 0.0062 DIA. [15.88 ± 1.575] DIA. THRU HOLE 0.125 [3.18] MAX. 0.250 [6.35] (3. b) CASE CODE A B R S 0.031 [0.79] (3. f) SECTION "A" - "A" TYPE 152D UNITS WITH INSULATING SLEEVE D 0.135 ± 0.016 [3.43 ± 0.41] 0.185 ± 0.016 [4.70 ± 0.41] 0.289 ± 0.016 [7.34 ± 0.41] 0.351 ± 0.016 [8.92 ± 0.41] 0.750 [19.05] “A” LABEL (4.a) L 0.286 ± 0.031 [7.26 ± 0.79] 0.474 ± 0.031 [12.04 ± 0.79] 0.686 ± 0.031 [17.42 ± 0.79] 0.786 ± 0.031 [19.96 ± 0.79] LEAD SIZE J (MAX.) AWG NO. 0.422 [10.72] 0.610 [15.49] 0.822 [20.88] 0.922 [23.42] 24 24 22 22 NOM. DIA. 0.020 [0.51] 0.020 [0.51] 0.025 [0.64] 0.025 [0.64] BOTH SIDES (3. f) COMPONENT SPACING TAPE SPACING A 0.200 ± 0.015 [5.08 ± 0.38] 0.200 ± 0.015 [5.08 ± 0.38] 0.400 ± 0.015 [10.16 ± 0.38] 0.400 ± 0.015 [10.16 ± 0.38] B 2.500 ± 0.062 [63.5 ± 1.57] 2.500 ± 0.062 [63.5 ± 1.57] 2.875 ± 0.062 [73.03 ± 1.57] 2.875 ±0.062 [73.03 ± 1.57] UNITS PER REEL 1000 1000 500 500 STANDARD REEL PACKAGING INFORMATION 1. Component Leads: a. Component leads shall not be bent beyond 0.047" [1.19 mm] maximum from their nominal position when measured from the leading edge of the component lead at the lead egress from the component. b. The “C” dimension shall be governed by the overall length of the reel packaged component. The distance between flanges shall be 0.125" to 0.250" [3.18 mm to 6.35 mm] greater than the overall component length. 2. Orientation: a. All polarized components must be oriented to one direction. The cathode lead tape shall be a color and the anode lead tape shall be white. 3. Reeling: a. Components on any reel shall not represent more than two date codes when date code identification is required. b. Component leads shall be positioned between pairs of 0.250" [6.35 mm] tape. c. The disposable reels have hubs and corrugated fibreboard flanges and core or equivalent. d. A minimum of 12" [304.8 mm] leader of tape shall be provided before the first and after the last component on the reel. e. 50 or 60 lb. Kraft paper must be wound between layer of components as far as necessary for component protection. Width of paper to be 0.062" to 0.250" [1.57 mm to 6.35 mm] less than the “C” dimension of the reel. f. A row of components must be centered between tapes ± 0.047" [1.19 mm]. In addition, individual www.vishay.com 30 components may deviate from center of component row ± 0.031" [0.79 mm]. g. Staples shall not be used for splicing. Not more than 4 layers of tape shall be used in any splice area and no tape shall be offset from another by more than 0.031" [0.79 mm] non-cumulative. Tape splices shall overlap at least 6" [152.4 mm] for butt joints and at least 3"[76.2 mm] for lap joints and shall not be weaker than unspliced tape. Universal splicing clips may also be used. h. Quantity per reel shall be controlled so that tape components and cover shall not extend beyond the smallest dimension of the flange (either across flats or diameter). Once the quantity per reel for each part number has been established, future orders for that part number shall be packaged in that quantity. When order or release quantity is less than the established quantity, a standard commercial pack is to be used. i. A maximum of 0.25 % of the components per reel quantity may be missing without consecutive missing components. j. Adequate protection must be provided to prevent physical damage to both reel and components during shipment and storage. 4. Marking: Minimum reel and carton marking shall consist of the following: Customer Part Number, Purchase Order No., Quantity, Package Date, Manufacturer's Name, Electrical Value, Date Code, Vishay Sprague Part Number and Country of Origin. For technical questions, contact: tantalum@vishay.com Document Number: 40016 Revision: 18-Jan-08 550D Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors for High Frequency Power Supplies FEATURES • Terminatons: Tin/lead (SnPb), 100 % Tin (RoHS compliant) Available • Hermetically-sealed, axial-lead solid tantalum RoHS* capacitors COMPLIANT • Small size and long life • Exceptional capacitance stability and excellent resistance to severe environmental conditions • The military equivalent is the CSR21 which is qualified to MIL-C-39003/09 APPLICATIONS Designed for power supply filtering applications at above 100 kHz PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 °C to + 85 °C, (To + 125 °C with voltage derating.) Capacitance Tolerance: At 120 Hz, + 25 °C. ± 20 %, ± 10 % standard. ± 5 % available as special Dissipation Factor: At 120 Hz, + 25 °C. Dissipation factor, as determined from the expression 2πRC, shall not exceed the values listed in the Standard Ratings Tables DC Leakage Current (DCL Max.): At + 25°C: Leakage current shall not exceed the values listed in he Standard Ratings Tables At + 85°C: Leakage current shall not exceed 10 times the values listed in the Standard Ratings Tables. At +125°C: Leakage shall not exceed 15 times the values listed in the Standard Ratings Tables. Life Test: Capacitors shall withstand rated DC voltage applied at + 85 °C for 2000 h or derated DC voltage applied at + 125 °C for 1000 h. Following the life test: 1. DCL shall not exceed 125 % of the initial requirements. 2. Dissipation Factor shall meet the initial requirement. 3. Change in capacitance shall not exceed ± 5 % ORDERING INFORMATION 550D MODEL 157 CAPACITANCE X0 CAPACITANC E TOLERANCE X0 = ± 20 % This is expressed in picofarads. X9 = ± 10 % The first two digits are the significant figures. The third is the X5 = ± 5 % number of zeros to follow. * Special order Standard capacitance ratings are in accordance with EIA preferred number series wherever possible. 006 DC VOLTAGE RATING AT + 85 °C This is expressed in volts. To complete the three-digit block, zeros precede the voltage rating. R CASE CODE See Ratings and Case Codes Table. 2 STYLE NUMBER 2= Insulated sleeve T PACKAGING E3 ROHS COMPLIANT E3 = 100 % tin termination (RoHS compliant) Blank = SnPb termination T = Tape and Reel DIMENSIONS in inches [millimeters] 1.500 ± 0.250 [38.10 ± 6.35] 1.500 ± 0.250 [38.10 ± 6.35] D DIA. L SOLID TINNED LEADS CASE CODE R S WITH INSULATING SLEEVE (1) D 0.289 ± 0.016 [7.34 ± 0.41] 0.351 ± 0.016 [8.92 ± 0.41] L 0.686 ± 0.031 [17.42 ± 0.79] 0.786 ± 0.031 [19.96 ± 0.79] 0.047 [1.19] MAX. 0.125 [3.18] MAX. J MAX. J (MAX.) 0.822 [20.880] 0.922 [23.420] LEAD SIZE AWG NO. 22 22 NOMINAL DIA. 0.025 [0.64] 0.025 [0.64] Notes: (1) When a shrink-fitted insulation is used, it shall lap over the ends of the capacitor body * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 40017 Revision: 28-Nov-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 31 550D Solid-Electrolyte TANTALEX® Capacitors for High Frequency Power Supplies Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) CASE CODE 150 180 220 270 330 R R S S S 82 100 120 150 180 220 R R R S S S 56 68 82 100 120 150 R R S S S S 27 33 39 47 56 68 82 100 R R R R S S S S 8.2 10 12 15 18 22 27 33 39 47 R R R R R R S S S S 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 R R R R R R R S PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % Max. DCL at + 25 °C (µA) Max. DF at + 25 °C 120 Hz (%) 6 WVDC AT + 85 °C, SURGE = 8 V . . . 4 WVDC AT + 125 °C, SURGE = 5 V 550D157X0006R2 550D157X9006R2 9 10 550D187X0006R2 550D187X9006R2 11 10 550D227X0006S2 550D227X9006S2 12 10 550D277X0006S2 550D277X9006S2 13 10 550D337X0006S2 550D337X9006S2 15 12 10 WVDC AT + 85 °C, SURGE = 13 V . . . 7 WVDC AT + 125 °C, SURGE = 9 V 550D826X0010R2 550D826X9010R2 8 8 550D107X0010R2 550D107X9010R2 10 8 550D127X0010R2 550D127X9010R2 12 8 550D157X0010S2 550D157X9010S2 15 8 550D187X0010S2 550D187X9010S2 18 8 550D227X0010S2 550D227X9010S2 20 10 15 WVDC AT + 85 °C, SURGE = 20 V . . . 10 WVDC AT + 125 °C, SURGE = 12 V 550D566X0015R2 550D566X9015R2 8 6 550D686X0015R2 550D686X9015R2 10 6 550D826X0015S2 550D826X9015S2 12 6 550D107X0015S2 550D107X9015S2 15 8 550D127X0015S2 550D127X9015S2 18 8 550D157X0015S2 550D157X9015S2 20 8 20 WVDC AT + 85 °C, SURGE = 26 V . . . 13 WVDC AT + 125 °C, SURGE = 16 V 550D276X0020R2 550D276X9020R2 5 5 550D336X0020R2 550D336X9020R2 7 5 550D396X0020R2 550D396X9020R2 8 5 550D476X0020R2 550D476X9020R2 9 6 550D566X0020S2 550D566X9020S2 11 6 550D686X0020S2 550D686X9020S2 14 6 550D826X0020S2 550D826X9020S2 16 6 550D107X0020S2 550D107X9020S2 20 8 35 WVDC AT + 85 °C, SURGE = 46 V . . . 23 WVDC AT + 125 °C, SURGE = 28 V 550D825X0035R2 550D825X9035R2 3 4 550D106X0035R2 550D106X9035R2 4 4 550D126X0035R2 550D126X9035R2 4 4 550D156X0035R2 550D156X9035R2 5 4 550D186X0035R2 550D186X9035R2 6 4 550D226X0035R2 550D226X9035R2 8 4 550D276X0035S2 550D276X9035S2 9 4 550D336X0035S2 550D336X9035S2 11 5 550D396X0035S2 550D396X9035S2 14 5 550D476X0035S2 550D476X9035S2 16 5 50 WVDC AT + 85 °C, SURGE = 65 V . . . 33 WVDC AT + 125 °C, SURGE = 40 V 550D565X0050R2 550D565X9050R2 4 3 550D685X0050R2 550D685X9050R2 4 3 550D825X0050R2 550D825X9050R2 5 3 550D106X0050R2 550D106X9050R2 5 3 550D126X0050R2 550D126X9050R2 6 3 550D156X0050R2 550D156X9050R2 8 3 550D186X0050R2 550D186X9050R2 9 4 550D226X0050S2 550D226X9050S2 11 4 Max. ESR at + 25 °C 100 kHz (Ω) 0.065 0.060 0.055 0.050 0.045 0.085 0.075 0.070 0.065 0.060 0.055 0.100 0.095 0.085 0.075 0.070 0.065 0.145 0.130 0.120 0.110 0.100 0.095 0.085 0.075 0.250 0.230 0.210 0.190 0.175 0.160 0.145 0.130 0.120 0.110 0.300 0.275 0.250 0.230 0.210 0.190 0.175 0.160 Note: (1) Insert capacitance tolerance code “X5”; for ± 5 % units (special order). www.vishay.com 32 For technical questions, contact: tantalum@vishay.com Document Number: 40017 Revision: 28-Nov-07 550D Solid-Electrolyte TANTALEX® Capacitors for High Frequency Power Supplies Vishay Sprague TAPE AND REEL PACKAGING in inches [millimeters] 13.0 [330.2] “A” STANDARD REEL TAPE SPACING B 1.126 to 3.07 [28.6 to 78.0] A I. D. REEL HUB COMPONENT SPACING 1.374 to 3.626 [34.9 to 92.1] 0.047 [1.19] MAX. OFF CENTER (1. a) 0.625 ± 0.0062 DIA. [15.88 ± 1.575] DIA. THRU HOLE 0.125 [3.18] MAX. 0.250 [6.35] (3. b) CASE CODE 0.750 [19.05] “A” LABEL (4. a) 0.031 [0.79] (3. f) SECTION "A" - "A" TYPE 550D UNITS WITH INSULATING SLEEVE LEAD SIZE J (MAX.) D L R 0.289 ± 0.016 [7.34 ± 0.41] 0.686 ± 0.031 [17.42 ± 0.79] S 0.351 ± 0.016 [8.92 ± 0.41] 0.786 ± 0.031 [19.96 ± 0.79] BOTH SIDES (3. f) COMPONENT SPACING TAPE SPACING UNITS PER REEL AWG NO. NOM. DIA. A B 0.822 [20.88] 22 0.025 [0.64] 0.400 ± 0.015 [10.16 ± 0.38] 2.875 ± 0.062 [73.03 ± 1.57] 500 0.922 [23.42] 22 0.025 [0.64] 0.400 ± 0.015 [10.16 ± 0.38] 2.875 ±0.062 [73.03 ± 1.57] 500 STANDARD REEL PACKAGING INFORMATION 1. Component Leads: a. Component leads shall not be bent beyond 0.047" [1.19 mm] maximum from their nominal position when measured from the leading edge of the component lead at the inside tape edge and at the lead egress from the component. b. The “C” dimension shall be governed by the overall length of the reel packaged component. The distance between flanges shall be 0.125" to 0.250" [3.18 mm to 6.35 mm] greater than the overall component length. 2. Orientation: a. All polarized components must be oriented to one direction. The cathode lead tape shall be a color and the anode lead tape shall be white. 3. Reeling: a. Components on any reel shall not represent more than two date codes when date code identification is required. b. Component leads shall be positioned between pairs of 0.250" [6.35 mm] tape. c. The disposable reels have hubs with corrugated fibreboard flanges and core or equivalent. d. A minimum of 12" [304.8 mm] leader of tape shall be provided before the first and after the last component on the reel. e. 50 or 60 lb. Kraft paper must be wound between layer of components as far as necessary for component protection. Width of paper to be 0.062" to 0.250" [1.57 mm to 6.35 mm] less than the “C” dimension of the reel. Document Number: 40017 Revision: 28-Nov-07 f. A row of components must be centered between tapes ± 0.047" [1.19 mm]. In addition, individual components may deviate from center of component row ± 0.031" [0.79 mm]. g. Staples shall not be used for splicing. Not more than 4 layers of tape shall be used in any splice area and no tape shall be offset from another by more than 0.031" [0.79 mm] non-cumulative. Tape splices shall overlap at least 6" [152.4 mm] for butt joints and at least 3" [76.2 mm] for lap joints and shall not be weaker than unspliced tape. Universal splicing clips may also be used. h. Quantity per reel shall be controlled so that tape components and cover shall not extend beyond the smallest dimension of the flange (either across flats or diameter). Once the quantity per reel for each part number has been established, future orders for that part number shall be packaged in that quantity. When order or release quantity is less than the established quantity, a standard commercial pack is to be used. i. A maximum of 0.25 % of the components per reel quantity may be missing without consecutive missing components. j. Adequate protection must be provided to prevent physical damage to both reel and components during shipment and storage. 4. Marking: a. Minimum reel and carton marking shall consist of the following: Customer Part Number, Purchase Order No., Quantity, Package Date, Manufacturer's name, Electrical Value, Date Code, Vishay Sprague Part Number and Country of Origin. For technical questions, contact: tantalum@vishay.com www.vishay.com 33 550D Solid-Electrolyte TANTALEX® Capacitors for High Frequency Power Supplies Vishay Sprague TYPICAL CURVES AT + 25 °C, IMPEDANCE AND ESR VS. FREQUENCY 10 10 IMPEDANCE IMPEDANCE ESR ESR 1 330 µF, 6 V Ω Ω 1 180 µF, 6 V 120 µF, 10 V 120 µF, 10 V 180 µF, 6 V 0.1 220 µF, 10 V 0.1 220 µF, 10 V 150 µF, 6 V 0.01 0.01 100 1K 10K 100K 1M 100 10M 1K 10K 100K 1M 10M FREQUENCY IN Hz FREQUENCY IN Hz 10 10 IMPEDANCE IMPEDANCE ESR ESR 1 1 150 µF, 15 V 47µF, 20 V Ω 100 µF, 20 V Ω 68 µF, 15 V 68 µF, 15 V 47 µF, 20 V 0.1 0.1 150 µF, 15 V 100 µF, 20 V 0.01 0.01 100 1K 10K 100K 1M 10M 100 1K FREQUENCY IN Hz 10K 100K 1M 10M FREQUENCY IN Hz 10 10 IMPEDANCE IMPEDANCE ESR ESR 47 µF, 35 V 22 µF, 50 V 1 1 22 µF, 35 V Ω Ω 22 µF, 35 V 18 µF, 50 V 18 µF, 50 V 0.1 0.1 22 µF, 50 V 47 µF, 35 V 0.01 0.01 100 1K 10K 100K 1M 10M 100 1K FREQUENCY IN Hz www.vishay.com 34 For technical questions, contact: tantalum@vishay.com 10K 100K 1M 10M FREQUENCY IN Hz Document Number: 40017 Revision: 28-Nov-07 550D Solid-Electrolyte TANTALEX® Capacitors for High Frequency Power Supplies Vishay Sprague PERFORMANCE CHARACTERISTICS • Operating Temperature: Capacitors are designed to operate over the temperature range of - 55 °C to + 85 °C with no derating. - 55 °C - 10 % + 85 °C RATING Dissipation Factor: The dissipation factor, determined from the expression 2πfRC, shall not exceed values listed in the Standard Ratings Table. 6.1 Measurements shall be made by the bridge method at, or referred to, a frequency of 1000 Hz and a temperature of + 25 °C. 7. Leakage Current: Capacitors shall be stabilized at the rated temperature for 30 min. Rated voltage shall be applied to capacitors for 5 min using a steady source of power (such as a regulated power supply) with 1000 Ω resistor connected in series with the capacitor under test to limit the charging current. Leakage current shall then be measured. + 125 °C RATING Surge Voltage (V) Working Voltage (V) Surge Voltage (V) 6 10 15 20 35 50 8 13 20 26 46 65 4 7 10 13 23 33 5 9 12 16 28 40 2. DC Working Voltage: The DC working voltage is the maximum operating voltage for continuous duty at the rated temperature. 3. Surge Voltage: The surge DC rating is the maximum voltage to which the capacitors may be subjected under any conditions, including transients and peak ripple at the highest line voltage. 3.2 TYPICAL LEAKAGE CURRENT FACTOR RANGE AT + 25 °C 1.0 0.8 0.7 0.6 0.5 0.4 Surge Voltage Test: Capacitors shall withstand the surge voltage applied in series with a 33 Ω ± 5 % resistor at the rate of 1.5 min on, 1.5 min off at + 85 °C, for 1000 successive test cycles. Following the surge voltage test, the dissipation factor and the leakage current shall meet the initial requirements; the capacitance shall not have changed more than ± 10 %. 4. Capacitance Tolerance: The capacitance of all capacitors shall be within the specified tolerance limits of the nominal rating. 4.1 Capacitance measurements shall be made by means of polarized capacitance bridge. The polarizing voltage shall be of such magnitude that there shall be no reversal of polarity due to the AC component. The maximum voltage applied to capacitors during measurement shall be 2 Vrms at 1000 Hz at + 25 °C. If the AC voltage applied is less than one-half volt rms, no DC bias is required. Measurement accuracy of the bridge shall be within ± 2 %. 5. Note that the leakage current varies with temperature and applied voltage. See graph below for the appropriate adjustment factor. Capacitance Change With Temperature: The capacitance change with temperature shall not exceed the following percentage of the capacitance measured at + 25 % 0.3 0.2 LEAKAGE CURRENT FACTOR 3.1 + 125 °C + 12 % 6. • Capacitors may be operated up to + 125 °C with voltage derating to two-thirds the + 85 °C rating. Working Voltage (V) + 85 °C +8% 0.1 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0.008 0.007 0.006 0.005 0.004 0.003 0.002 0.001 0 10 20 30 40 50 60 70 80 90 100 PERCENT OF RATED VOLTAGE Document Number: 40017 Revision: 28-Nov-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 35 550D Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors for High Frequency Power Supplies PERFORMANCE CHARACTERISTICS (Continued) 7.1 At + 25 °C, the leakage current shall not exceed the value listed in the Standard Ratings Table. 0.06" [1.52] ± 10 % maximum total excursion or 20 g peak, whichever is less. 7.2 At + 85 °C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings Table. 10.3.1 Vibration Frequency shall be varied logarithmically from 50 Hz to 2000 Hz and return to 50 Hz during a cycle period of 20 minutes. 7.3 At + 125 °C, the leakage current shall not exceed 15 times the value listed in the Standard Ratings Table. 10.3.2 The vibration shall be applied for 4 h in each of 2 directions, parallel and perpendicular to the major axis of the capacitors. 8. Life Test: Capacitors shall withstand rated DC voltage applied at + 85 °C for 2000 h or rated DC voltage applied at + 125 °C for 1000 h. 10.3.3 Rated DC voltage shall be applied during the vibration cycling. 8.1 Following the life test, the dissipation factor shall meet the initial requirement; the capacitance change shall not exceed ± 2 %; the leakage current shall not exceed 125 % of the original requirement. 9. Shelf Test: Capacitors shall withstand a shelf test for 5000 h at a temperature of + 85 °C, with no voltage applied. 9.1 Following the shelf test, the leakage current shall meet the initial requirement; the dissipation factor shall not exceed 150 % of the initial requirement; the capacitance change shall not exceed ± 5 %. 10 10.1 10.2 Vibration Tests: Capacitors shall be subjected to vibration tests in accordance with the following criteria. Capacitors shall be secured for test by means of a rigid mounting using suitable brackets. Low Frequency Vibration: Vibration shall consist of a simple harmonic motion having an amplitude of 0.03" [0.76] and a maximum total excursion of 0.06" [1.52], in a direction perpendicular to the major axis of the capacitor. 10.2.1 Vibration frequency shall be varied uniformly between the approximate limits of 10 Hz to 55 Hz during a period of approximately one minute, continuously for 1 and 1.5 h. 10.2.2 A cathode ray oscilloscope or other comparable means shall be used in determining electrical intermittency during the final 30 minutes of the test. The AC voltage applied shall not exceed 2 volts rms. 10.2.3 Electrical tests shall show no evidence of intermittent contacts, open circuits or short circuits during these tests. 10.2.4 Following the low frequency vibration test, capacitors shall meet the original requirements for leakage current and dissipation factor; capacitance change shall not exceed ± 5 % of the original measured value. 10.3 High Frequency Vibration: Vibration shall consist of a simple harmonic motion having an amplitude of www.vishay.com 36 10.3.4 A cathode ray oscilloscope or other comparable means shall be used in determining electrical intermittency during test. The AC voltage applied shall not exceed 2 Vrms. 10.3.5 Electrical tests shall show no evidence of intermittent contacts, open circuits or short circuits during these tests. 10.3.6 There shall be no mechanical damage to these capacitors as a result of these tests. 10.3.7 Following the high frequency vibration test, capacitors shall meet the original limits for capacitance, dissipation factor and leakage current. 11. Acceleration Test: 11.1 Capacitors shall be rigidly mounted by means of suitable brackets. 11.2 Capacitors shall be subjected to a constant acceleration of 100 g for a period of 10 s in each of 2 mutually perpendicular planes. 11.2.1 The direction of motion shall be parallel to and perpendicular to the cylindrical axis of the capacitors. 11.3 Rated DC voltage acceleration test. shall be applied during 11.3.1 A cathode ray oscilloscope or other comparable means shall be used in determining electrical intermittency during test. The AC voltage applied shall not exceed 2 Vrms. 11.4 Electrical tests shall show no evidence of intermittent contacts, open circuits or short circuits during these tests. 11.5 There shall be no mechanical damage to these capacitors as a result of these tests. 11.6 Following the acceleration test, capacitors shall meet the original limits for capacitance, dissipation factor and leakage current. 12. Shock Test: 12.1 Capacitors shall be rigidly mounted by means of suitable brackets. The test load shall be distributed uniformly on the test platform to minimize the effects of unbalanced loads. For technical questions, contact: tantalum@vishay.com Document Number: 40017 Revision: 28-Nov-07 550D Solid-Electrolyte TANTALEX® Capacitors for High Frequency Power Supplies Vishay Sprague PERFORMANCE CHARACTERISTICS (Continued) 12.1.1 Test equipment shall be adjusted to produce a shock of 100 g peak with a duration of 6 ms and a sawtooth waveform at a velocity change of 9.7 ft./s. 12.2 Capacitors shall be subjected to 3 shocks applied in each of 3 directions corresponding to the 3 mutually perpendicular axes of the capacitors. 12.3 Rated DC voltage shall be applied to capacitors during test. 12.3.1 A cathode ray oscilloscope or other comparable means shall be used in determining electrical intermittency during test. The AC voltage applied shall not exceed 2 Vrms. 12.4 Electrical tests shall show no evidence of intermittent contacts, open circuits or short circuits during these tests. 12.5 There shall be no mechanical damage to these capacitors as a result of these tests. 12.6 Following the shock test, capacitors shall meet the original limits for capacitance, dissipation factor and leakage current. 13. Moisture Resistance: 13.1 Capacitors shall be subjected to temperature cycling at 90 % to 98 % relative humidity, in a test chamber constructed of non-reactive materials (non-resiniferous and containing no formaldehyde or phenol). Steam or distilled, demineralized or deionized water having a pH value between 6.0 and 7.2 at + 23 °C shall be used to obtain the required humidity. No rust, corrosive contaminants or dripping condensate shall be imposed on test specimens. 13.1.1 Capacitors shall be mounted by their normal mounting means in a normal mounting position and placed in a test chamber so that uniform and thorough exposure is obtained. 13.1.2 No conditioning or initial measurements will be performed prior to temperature cycling. Polarization and load voltages are not applicable. maximum total excursion of 0.06" [1.52] varied uniformly from 10 Hz to 55 Hz to 10 Hz over a period of 1 min, for 15 cycles. 13.1.7 Capacitors shall then be returned to temperature/ humidity cycling. 13.2 After completion of temperature cycling, capacitors shall be removed from the test chamber and stabilized at room temperature for 2 to 6 h. 13.3 Capacitors shall show no evidence of harmful or extensive corrosion, obliteration or marking or other visible damage. 13.4 Following the moisture resistance test, capacitors shall meet the original limits for capacitance, dissipation factor and leakage current. 14. Insulating Sleeves: 14.1 Capacitors with insulating sleeves shall withstand a 2000 VDC potential applied for 1 min between the case and a metal “V” block in intimate contact with the insulating sleeve. 14.2 Capacitors with insulating sleeves shall have the insulation resistance measured between the case and a metal “V” block in intimate contact with the insulating sleeve. The insulation resistance shall be at least 1000 MΩ 15. Thermal Shock And Immersion Cycling: 15.1 Capacitors shall be conditioned prior to temperature cycling for 15 min at + 25 °C, at less than 50 % relative humidity and a barometric pressure at 28 to 31". 15.2 Capacitors shall be subjected to thermal shock in a cycle of exposure to ambient air at - 65 °C (+ 0 °C, - 5 °C) for 30 min, then, + 25 °C (+ 10 °C, - 5 °C) for 5 min, then + 125 °C (+ 3 °C, - 0 °C) for 30 min, then + 25 °C (+ 10 °C, - 5 °C) for 5 min, for 5 cycles. 15.3 Between 4 and 24 h after temperature cycling, capacitors shall be subjected to immersion in a bath of fresh tap water with the non-corrosive dye Rhodamine B added, at + 65 °C (+ 5 °C, - 0 °C) for 15 min, then, within 3 s, immersed in a saturated solution of sodium chloride and water with Rhodamine B added, at a temperature of + 25 °C (+ 10 °C, - 5 °C) for 15 min, for 2 cycles. 13.1.3 Capacitors shall be subjected to temperature cycling from + 25 °C to + 65 °C to + 25 °C (+ 10 °C, - 2 °C) over a period of 8 h, at 90 % to 98 % relative humidity, for 20 cycles. 13.1.4 Temperature cycling shall be stopped after an even number of cycles 5 times during the first 18 cycles, and the capacitor shall be alloweed to stabilize at high humidity for 1 to 4 h. 13.1.5 After stabilization, capacitors shall be removed from the humidity chamber and shall be conditioned for 3 h at - 10 °C ± 2 °C. 13.1.6 After cold conditioning, capacitors shall be subjected to vibration cycling consisting of a simple harmonic vibration having an amplitude of 0.03" [0.76] and a Document Number: 40017 Revision: 28-Nov-07 15.3.1 Capacitors shall be thoroughly rinsed and wiped or air-blasted dry immediately upon removal from immersion cycling. 15.4 Capacitors shall show no evidence of harmful or extensive corrosion, obliteration of marking or other visible damage. For technical questions, contact: tantalum@vishay.com www.vishay.com 37 550D Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors for High Frequency Power Supplies PERFORMANCE CHARACTERISTICS (Continued) 15.5 Following the thermal shock immersion cycling test, capacitors shall meet the original requirements for leakage current and dissipation factor; capacitance change shall not exceed ± 5 % of the original measured value. 15.6 Capacitors shall be opened and examined. There shall be no evidence of dye penetration. 16. Reduced Pressure Test: 16.1 Capacitors shall be stabilized at a reduced pressure of 0.315" [8.0] of mercury, equivalent to an altitude of 100 000 feet [30.480 m], for a period of 5 min. 16.2 Rated DC voltage shall be applied for 1 min. 16.3 Capacitors shall not flash over nor shall end seals be damaged. 16.4 Following the reduced pressure test, the capacitance, equivalent series resistance and leakage current shall meet the original requirements. 17. Lead Pull Test: Leads shall withstand a tensile stress of 3 pounds (1.4 kg) applied in any direction for 30 s. 18. Marking: Capacitors shall be marked with Sprague or (2); the type number 550D; rated capacitance and tolerance, rated DC working voltage and the standard EIA date code. 18.1 Capacitors shall be marked on one end with a plus sign (+) to identify the positive terminal. 18.2 Vishay Sprague reserves the right to furnish capacitors of higher working voltages than those ordered, where the physical size of the higher voltage units is identical to that of the units ordered. 2. V rms = I rms × Z where, P= Power Dissipation in W at + 25 °C as given in the table in Paragraph Number 5 (Power Dissipation). The capacitor Equivalent Series RESR = Resistance at the specified frequency. Z= The capacitor Impedance at the specified frequency. 2.1 The sum of the peak AC voltage plus the DC voltage shall not exceed the DC voltage rating of the capacitor. 2.2 The sum of the negative peak AC voltage plus the applied DC voltage shall not allow a voltage reversal exceeding 15 % of the DC working voltage at + 25 °C. 3. Reverse Voltage: These capacitors are capable of withstanding peak voltages in the reverse direction equal to 15 % of the DC rating at + 25 °C, 10 % of the DC rating at + 55 °C; 5 % of the DC rating at + 85 °C. 4. Temperature Derating: If these capacitors are to be operated at temperatures above + 25 °C, the permissible rms ripple current or voltage shall be calculated using the derating factors as shown: GUIDE TO APPLICATION 1. A-C Ripple Current: The maximum allowable ripple current shall be determined from the formula: I rms = P ---------------R ESR where, Power Dissipation in W at + 25 °C as given in the table in Paragraph Number 5 (Power Dissipation) RESR = The capacitor Equivalent Series Resistance at the specified frequency. P= www.vishay.com 38 A-C Ripple Voltage: The maximum allowable ripple voltage shall be determined from the formula: P V rms = Z ---------------R ESR or, from the formula: 5. Temperature Derating Factor + 25 °C 1.0 + 55 °C 0.8 + 85 °C 0.6 + 125 °C 0.4 Power Dissipation: The figures shown relate to an approximate + 20 °C rise in case temperature measured in free air. Power dissipation will be affected by the heat sinking capability of the mounting surface. Non-sinusoidal ripple current may produce heating effects which differ from those shown. It is important that the equivalent Irms value be established when calculating permissable operating levels. Case Code Maximum Permissible Power Dissipation at + 25 °C (W in free air) R 0.185 S 0.225 For technical questions, contact: tantalum@vishay.com Document Number: 40017 Revision: 28-Nov-07 M39003/01/03/09 Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 FEATURES • Hermetically sealed • Metal cased • Axial lead • Tubular STYLE, DOCUMENT/DETAIL SPEC. Style CSR13, M39003/01 Style CSR23, M39003/03 Style CSR21, M39003/09 Solid-Electrolyte TANTALEX® Capacitors to Military Specification MIL-PRF-39003 - Exponential and Weibull Distribution: Hermetically sealed, metal cased, axial leaded tubular capacitors manufactured as Military Styles CSR13, CSR21 and CSR23. These capacitors are furnished to the requirements of the military specification, including marking, testing and inspection. In accordance with the specification, all capacitors are marked with the Military Part Number (M39003/xx-xxxx) rather than the older Style designation (CSRxxxxxxxx) and should be ordered as such. All capacitors covered by MIL-PRF-39003 are now ordered with the Military Part Number as illustrated in the Part Numbering System chart. Capacitors must not be ordered using the Style number identification. MIL-PRF-39003 establishes failure rates (expressed in percent per 1000 h) based on exponential and Weibull distribution. Care must be exercised in ordering to insure the part number correctly identifies the desired failure rate level. Exponential failure rates are identified as levels M, P, R and S; Weibull failure rates are B, C and D. Failure rate levels M, P, R and S are inactive for new designs. In addition, each order for Military Style CSR13, CSR23 capacitors requiring government inspection must state whether inspection is to be at the destination or at the Vishay Sprague Plant. Orders requiring source inspection cannot be shipped until this has been accomplished. Style CS13 capacitors previously shown in MIL-C-26655 are directly replaced by Style CSR13 and Style CSR23 capacitors are extended capacitance range versions of Military Style CSR13. For information on the performance characteristics of these capacitors, please refer to the latest issue of the military specification. MILITARY SPECIFICATION MIL-PRF-39003 PART NUMBERING SYSTEM INFORMATION M39003 BASIC DOCUMENT NUMBER /01 DETAIL SPECIFICATION Indicates the Basic Specification; Indicates the Detail in this case MIL-PRF-39003 Specification of the Basic Military Specification -2254 DASH NUMBER Taken from Standard/ Extended Ratings Tables A (1) SURGE CURRENT OPTION CODE Blank = Standard (no surge current) A = + 25 °C, after Weibull B = - 55 °C and + 85 °C, before Weibull C = - 55 °C and + 85 °C, before Weibull D = + 25 °C, after Weibull, High Temperature solder E = - 55 °C and + 85 °C, after Weibull, High Temperature solder F = - 55 °C and + 85 °C, after Weibull, High Temperature solder H = High Temperature solder only (no surge) Note: (1) The material in this section has been abstracted from MIL-PRF-39003. If questions about optional surge current testing or high temperature solder, please see MIL-PRF-39003, paragraph 1.2, table II. Document Number: 40018 Revision: 20-Nov-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 39 M39003/01/03/09 Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 Vishay Sprague DIMENSIONS in inches [millimeters] STYLE CSR13 STYLE CSR21 STYLE CSR23 1.500 ± 0.250 [38.10 ± 6.35] J D M 0.094 [2.4] Max. L CASE CODE L ± 0.031 [0.79] D + 0.016 [0.41] - 0.015 [0.38] M ± 0.002 [0.05] J (MAX.) A 0.286 [7.26] 0.135 [3.43] 0.020 [0.51] 0.422 [10.72] 0.610 [15.49] B 0.474 [12.04] 0.185 [4.70] 0.020 [0.51] C 0.686 [17.42] 0.289 [7.34] 0.025 [0.64] 0.822 [20.88] D 0.786 [19.96] 0.351 [8.92] 0.025 [0.64] 0.922 [23.42] Notes: The case insulation shall extend 0.015" [0.38 mm] minimum beyond each end. However, when a shrink-fitted insulation is used, it shall lap over the ends of the capacitor body. (2) A minimum lead length of 1.0" [2.54 mm] for use with tape and reel automatic insertion equipment is available upon request. (3) Failure Rate levels M, P, R and S are inactive for new design. Insulation is used, it shall lap over the ends of the capacitor body. (1) STANDARD RATINGS: CSR13, M39003/01-XXXX CAPACITANCE CASE (µF) CODE CAP. TOL. (± %) PART NO. M39003/01FAILURE RATE LEVEL (%/1000 h) M 1.0 P 0.1 R 0.01 S 0.001 B 0.1 C 0.01 MAX. DCL (µA) AT MAX. DF (%) AT - 55 °C + 85 °C D + 25 °C + 85 °C + 125 °C + 25 °C + 125 °C 0.001 6 WVDC AT + 85 °C, SURGE = 8 V . . . 4 WVDC AT + 125 °C, SURGE = 5 V 5.6 A 5 5001 5201 5401 5601 6001 7001 8001 0.3 6.0 7.5 4 4 5.6 A 10 2241 2481 2721 2961 6002 7002 8002 0.3 6.0 7.5 4 4 6.8 A 5 5002 5202 5402 5602 6003 7003 8003 0.3 6.0 7.5 6 6 6.8 A 10 2242 2482 2722 2962 6004 7004 8004 0.3 6.0 7.5 6 6 6.8 A 20 2243 2843 2723 2963 6005 7005 8005 0.3 6.0 7.5 6 6 47.0 B 5 5003 5203 5403 5603 6006 7006 8006 1.5 24.0 30.0 6 6 47.0 B 10 2244 2484 2724 2964 6007 7007 8007 1.5 24.0 30.0 6 6 47.0 B 20 2245 2485 2725 2965 6008 7008 8008 1.5 24.0 30.0 6 6 56.0 B 5 5004 5204 5404 5604 6009 7009 8009 1.5 24.0 30.0 6 6 56.0 B 10 2246 2486 2726 2966 6010 7010 8010 1.5 24.0 30.0 6 6 150.0 C 5 5005 5205 5405 5605 6011 7011 8011 4.5 90.0 113.0 8 8 150.0 C 10 2247 2487 2727 2967 6012 7012 8012 4.5 90.0 113.0 8 8 150.0 C 20 2248 2488 2728 2968 6013 7013 8013 4.5 90.0 113.0 8 8 180.0 C 5 5006 5206 5406 5606 6014 7014 8014 5.5 110.0 138.0 8 8 180.0 C 10 2249 2489 2729 2969 6015 7015 8015 5.5 110.0 138.0 8 8 270.0 D 5 5007 5207 5407 5607 6016 7016 8016 6.5 130.0 163.0 8 8 270.0 D 10 2250 2490 2730 2970 6017 7017 8017 6.5 130.0 163.0 8 8 330.0 D 5 5008 5208 5408 5608 6018 7018 8018 7.5 150.0 188.0 8 8 330.0 D 10 2251 2491 2731 2971 6019 7019 8019 7.5 150.0 188.0 8 8 330.0 D 20 2252 2492 2732 2972 6020 7020 8020 7.5 150.0 188.0 8 8 www.vishay.com 40 For technical questions, contact: tantalum@vishay.com Document Number: 40018 Revision: 20-Nov-07 M39003/01/03/09 Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 Vishay Sprague STANDARD RATINGS: CSR13, M39003/01-XXXX CAPACITANCE CASE (µF) CODE 3.9 3.9 4.7 4.7 4.7 27.0 27.0 33.0 33.0 33.0 39.0 39.0 82.0 82.0 100.0 100.0 100.0 120.0 120.0 180.0 180.0 220.0 220.0 220.0 A A A A A B B B B B B B C C C C C C C D D D D D 2.7 2.7 3.3 3.3 3.3 18.0 18.0 22.0 22.0 22.0 56.0 56.0 68.0 68.0 68.0 120.0 120.0 150.0 150.0 150.0 A A A A A B B B B B C C C C C D D D D D 1.2 1.2 1.5 1.5 1.5 1.5 1.8 A A A A A A A Document Number: 40018 Revision: 20-Nov-07 CAP. TOL. (± %) PART NO. M39003/01FAILURE RATE LEVEL (%/1000 h) MAX. DCL (µA) AT MAX. DF (%) AT - 55 °C + 85 °C M P R S B C D + 25 °C + 85 °C + 125 °C + 25 °C + 125 °C 1.0 0.1 0.01 0.001 0.1 0.01 0.001 10 WVDC AT + 85 °C, SURGE = 13 V . . . 7 WVDC AT + 125 °C, SURGE = 9 V 5 5009 5209 5409 5609 6021 7021 8021 0.3 6.0 7.5 4 4 10 2253 2493 2733 2973 6022 7022 8022 0.3 6.0 7.5 4 4 5 5010 5210 5410 5610 6023 7023 8023 0.4 7.0 8.8 4 4 10 2254 2494 2734 2974 6024 7024 8024 0.4 7.0 8.8 4 4 20 2255 2495 2735 2975 6025 7025 8025 0.4 7.0 8.8 4 4 5 5011 5211 5411 5611 6026 7026 8026 2.0 40.0 50.0 6 6 10 2256 2496 2736 2976 6027 7027 8027 2.0 40.0 50.0 6 6 5 5012 5212 5412 5612 6028 7028 8028 2.5 50.0 63.0 6 6 10 2257 2497 2737 2977 6029 7029 8029 2.5 50.0 63.0 6 6 20 2258 2498 2738 2978 6030 7030 8030 2.5 50.0 63.0 6 6 5 5013 5213 5413 5613 6031 7031 8031 2.5 50.0 63.0 6 6 10 2259 2499 2739 2979 6032 7032 8032 2.5 50.0 63.0 6 6 5 5014 5214 5414 5614 6033 7033 8033 4.0 80.0 100.0 6 6 10 2260 2500 2740 2980 6034 7034 8034 4.0 80.0 100.0 6 6 5 5015 5215 5415 5615 6035 7035 8035 5.0 100.0 125.0 8 8 10 2261 2501 2741 2981 6036 7036 8036 5.0 100.0 125.0 8 8 20 2262 2502 2742 2982 6037 7037 8037 5.0 100.0 125.0 8 8 5 5016 5216 5416 5616 6038 7038 8038 6.0 120.0 150.0 8 8 10 2263 2503 2743 2983 6039 7039 8039 6.0 120.0 150.0 8 8 5 5017 5217 5417 5617 6040 7040 8040 9.0 180.0 226.0 8 8 10 2264 2504 2744 2984 6041 7041 8041 9.0 180.0 226.0 8 8 5 5018 5218 5418 5618 6042 7042 8042 10.0 200.0 250.0 8 8 10 2265 2505 2745 2985 6043 7043 8043 10.0 200.0 250.0 8 8 20 2266 2506 2746 2986 6044 7044 8044 10.0 200.0 250.0 8 8 15 WVDC AT + 85 °C, SURGE = 20 V . . . 10 WVDC AT + 125 °C, SURGE = 12 V 5 5019 5219 5419 5619 6045 7045 8045 0.3 6.0 7.5 4 4 10 2267 2507 2747 2987 6046 7046 8046 0.3 6.0 7.5 4 4 5 5020 5220 5420 5620 6047 7047 8047 0.4 8.0 10.0 4 4 10 2268 2508 2748 2988 6048 7048 8048 0.4 8.0 10.0 4 4 20 2269 2509 2749 2989 6049 7049 8049 0.4 8.0 10.0 4 4 5 5021 5221 5421 5621 6050 7050 8050 2.0 35.0 44.0 6 6 10 2270 2510 2750 2990 6051 7051 8051 2.0 35.0 44.0 6 6 5 5022 5222 5422 5622 6052 7052 8052 2.0 40.0 50.0 6 6 10 2271 2511 2751 2991 6053 7053 8053 2.0 40.0 50.0 6 6 20 2272 2512 2752 2992 6054 7054 8054 2.0 40.0 50.0 6 6 5 5023 5223 5423 5623 6055 7055 8055 4.0 80.0 100.0 6 6 10 2273 2513 2753 2993 6056 7056 8056 4.0 80.0 100.0 6 6 5 5024 5224 5424 5624 6057 7057 8057 5.0 100.0 125.0 6 6 10 2274 2514 2754 2994 6058 7058 8058 5.0 100.0 125.0 6 6 20 2275 2515 2755 2995 6059 7059 8059 5.0 100.0 125.0 6 6 5 5025 5225 5425 5625 6060 7060 8060 9.0 180.0 226.0 8 8 10 2276 2516 2756 2996 6061 7061 8061 9.0 180.0 226.0 8 8 5 5026 5226 5426 5626 6062 7062 8062 10.0 200.0 250.0 8 8 10 2277 2517 2757 2997 6063 7063 8063 10.0 200.0 250.0 8 8 20 2278 2518 2758 2998 6064 7064 8064 10.0 200.0 250.0 8 8 20 WVDC AT + 85 °C, SURGE = 26 V . . . 13 WVDC AT + 125 °C, SURGE = 16 V 5 5027 5227 5427 5627 6065 7065 8065 0.3 6.0 7.5 4 4 10 2279 2519 2759 2999 6066 7066 8066 0.3 6.0 7.5 4 4 5 5028 5228 5428 5628 6067 7067 8067 0.3 6.0 7.5 4 4 10 2280 2520 2760 3000 6068 7068 8068 0.3 6.0 7.5 4 4 20 2281 2521 2761 3001 6069 7069 8069 0.3 6.0 7.5 4 4 5 5029 5229 5429 5629 6070 7070 8070 0.3 6.0 7.5 4 4 10 2282 2522 2762 3002 6071 7071 8071 0.3 6.0 7.5 4 4 For technical questions, contact: tantalum@vishay.com www.vishay.com 41 M39003/01/03/09 Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 Vishay Sprague STANDARD RATINGS: CSR13, M39003/01-XXXX CAPACITANCE CASE (µF) CODE 2.2 2.2 2.2 8.2 8.2 10.0 10.0 10.0 12.0 12.0 15.0 15.0 15.0 27.0 27.0 33.0 33.0 33.0 39.0 39.0 47.0 47.0 47.0 56.0 56.0 68.0 68.0 68.0 82.0 82.0 100.0 100.0 100.0 A A A B B B B B B B B B B C C C C C C C C C C D D D D D D D D D D 5.6 5.6 6.8 6.8 6.8 22.0 22.0 22.0 27.0 27.0 33.0 33.0 33.0 39.0 39.0 47.0 47.0 47.0 B B B B B C C C D D D D D D D D D D www.vishay.com 42 CAP. TOL. (± %) PART NO. M39003/01FAILURE RATE LEVEL (%/1000 h) MAX. DCL (µA) AT MAX. DF (%) AT - 55 °C + 85 °C M P R S B C D + 25 °C + 85 °C + 125 °C + 25 °C + 125 °C 1.0 0.1 0.01 0.001 0.1 0.01 0.001 20 WVDC AT + 85 °C, SURGE = 26 V . . . 13 WVDC AT + 125 °C, SURGE = 16 V 5 5030 5230 5430 5630 6072 7072 8072 0.4 8.0 10.0 4 4 10 2283 2523 2763 3003 6073 7073 8073 0.4 8.0 10.0 4 4 20 2284 2524 2764 3004 6074 7074 8074 0.4 8.0 10.0 4 4 5 5031 5231 5431 5631 6075 7075 8075 1.0 20.0 25.0 6 6 10 2285 2525 2765 3005 6076 7076 8076 1.0 20.0 25.0 6 6 5 5032 5232 5432 5632 6077 7077 8077 1.5 30.0 38.0 6 6 10 2286 2526 2766 3006 6078 7078 8078 1.5 30.0 38.0 6 6 20 2287 2527 2767 3007 6079 7079 8079 1.5 30.0 38.0 6 6 5 5033 5233 5433 5633 6080 7080 8080 1.8 35.0 44.0 6 6 10 2288 2528 2768 3008 6081 7081 8081 1.8 35.0 44.0 6 6 5 5034 5234 5434 5634 6082 7082 8082 2.0 40.0 50.0 6 6 10 2289 2529 2769 3009 6083 7083 8083 2.0 40.0 50.0 6 6 20 2290 2530 2770 3010 6084 7084 8084 2.0 40.0 50.0 6 6 5 5035 5235 5435 5635 6085 7085 8085 2.5 50.0 63.0 6 6 10 2291 2531 2771 3011 6086 7086 8086 2.5 50.0 63.0 6 6 5 5036 5236 5436 5636 6087 7087 8087 3.5 70.0 88.0 6 6 10 2292 2532 2772 3012 6088 7088 8088 3.5 70.0 88.0 6 6 20 2293 2533 2773 3013 6089 7089 8089 3.5 70.0 88.0 6 6 5 5037 5237 5437 5637 6090 7090 8090 4.0 80.0 100.0 6 6 10 2294 2534 2774 3014 6091 7091 8091 4.0 80.0 100.0 6 6 5 5038 5238 5438 5368 6092 7092 8092 4.5 90.0 113.0 6 6 10 2295 2535 2775 3015 6093 7093 8093 4.5 90.0 113.0 6 6 20 2296 2536 2776 3016 6094 7094 8094 4.5 90.0 113.0 6 6 5 5039 5239 5439 5639 6095 7095 8095 5.5 110.0 138.0 6 6 10 2297 2537 2777 3017 6096 7096 8096 5.5 110.0 138.0 6 6 5 5040 5240 5440 5640 6097 7097 8097 7.0 140.0 175.0 6 6 10 2298 2538 2778 3018 6098 7098 8098 7.0 140.0 175.0 6 6 20 2299 2539 2779 3019 6099 7099 8099 7.0 140.0 175.0 6 6 5 5041 5241 5441 5641 6100 7100 8100 8.0 160.0 200.0 6 6 10 2300 2540 2780 3020 6101 7101 8101 8.0 160.0 200.0 6 6 5 5042 5242 5442 5642 6102 7102 8102 10.0 200.0 250.0 8 8 10 2301 2541 2781 3021 6103 7103 8103 10.0 200.0 250.0 8 8 20 2302 2542 2782 3022 6104 7104 8104 10.0 200.0 250.0 8 8 35 WVDC AT + 85 °C, SURGE = 46 V . . . 23 WVDC AT + 125 °C, SURGE = 28 V 5 5043 5243 5443 5643 6105 7105 8105 1.3 25.0 32.0 4 4 10 2303 2543 2783 3023 6106 7106 8106 1.3 25.0 32.0 4 4 5 5044 5244 5444 5644 6107 7107 8107 1.5 30.0 38.0 6 6 10 2304 2544 2784 3024 6108 7108 8108 1.5 30.0 38.0 6 6 20 2305 2545 2785 3025 6109 7109 8109 1.5 30.0 38.0 6 6 5 5045 5245 5445 5645 6110 7110 8110 4.0 80.0 100.0 6 6 10 2306 2546 2786 3026 6111 7111 8111 4.0 80.0 100.0 6 6 20 2307 2547 2787 3027 6112 7112 8112 4.0 80.0 100.0 6 6 5 5046 5246 5446 5646 6113 7113 8113 4.5 90.0 113.0 6 6 10 2308 2548 2788 3028 6114 7114 8114 4.5 90.0 113.0 6 6 5 5047 5247 5447 5647 6115 7115 8115 5.5 110.0 138.0 6 6 10 2309 2549 2789 3029 6116 7116 8116 5.5 110.0 138.0 6 6 20 2310 2550 2790 3030 6117 7117 8117 5.5 110.0 138.0 6 6 5 5048 5248 5448 5648 6118 7118 8118 7.0 140.0 175.0 6 6 10 2311 2551 2791 3031 6119 7119 8119 7.0 140.0 175.0 6 6 5 5049 5249 5449 5649 6120 7120 8120 8.0 160.0 200.0 6 6 10 2312 2552 2792 3032 6121 7121 8121 8.0 160.0 200.0 6 6 20 2313 2553 2793 3033 6122 7122 8122 8.0 160.0 200.0 6 6 For technical questions, contact: tantalum@vishay.com Document Number: 40018 Revision: 20-Nov-07 M39003/01/03/09 Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 Vishay Sprague STANDARD RATINGS: CSR13, M39003/01-XXXX CAPACITANCE CASE (µF) CODE 0.056 0.056 0.068 0.068 0.068 0.082 0.082 0.10 0.10 0.10 0.12 0.12 0.15 0.15 0.15 0.18 0.18 0.22 0.22 0.22 0.27 0.27 0.33 0.33 0.33 0.39 0.39 0.47 0.47 0.47 0.56 0.56 0.68 0.68 0.68 0.82 0.82 1.0 1.0 1.0 1.2 1.2 1.5 1.5 1.5 1.8 1.8 2.2 2.2 2.2 2.7 2.7 3.3 3.3 A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A B B B B B B B B B B B B B B Document Number: 40018 Revision: 20-Nov-07 CAP. TOL. (± %) PART NO. M39003/01FAILURE RATE LEVEL (%/1000 h) MAX. DCL (µA) AT MAX. DF (%) AT - 55 °C + 85 °C M P R S B C D + 25 °C + 85 °C + 125 °C + 25 °C + 125 °C 1.0 0.1 0.01 0.001 0.1 0.01 0.001 50 WVDC AT + 85 °C, SURGE = 65 V . . . 33 WVDC AT + 125 °C, SURGE = 40 V 5 5063 5263 5463 5663 6156 7156 8156 0.3 5.0 6.3 2 4 10 2334 2574 2814 3054 6157 7157 8157 0.3 5.0 6.3 2 4 5 5064 5264 5464 5664 6158 7158 8158 0.3 5.0 6.3 2 4 10 2335 2575 2815 3055 6159 7159 8159 0.3 5.0 6.3 2 4 20 2336 2576 2816 3056 6160 7160 8160 0.3 5.0 6.3 2 4 5 5065 5265 5465 5665 6161 7161 8161 0.3 5.0 6.3 2 4 10 2337 2577 2817 3057 6162 7162 8162 0.3 5.0 6.3 2 4 5 5066 5266 5466 5666 6163 7163 8163 0.3 5.0 6.3 2 4 10 2338 2578 2818 3058 6164 7164 8164 0.3 5.0 6.3 2 4 20 2339 2579 3819 3059 6165 7165 8165 0.3 5.0 6.3 2 4 5 5067 5267 5467 5667 6166 7166 8166 0.3 5.0 6.3 2 4 10 2340 2580 2820 3060 6167 7167 8167 0.3 5.0 6.3 2 4 5 5068 5268 5468 5668 6168 7168 8168 0.3 5.0 6.3 2 4 10 2341 2581 2821 3061 6169 7169 8169 0.3 5.0 6.3 2 4 20 2342 2582 2822 3062 6170 7170 8170 0.3 5.0 6.3 2 4 5 5069 5269 5469 5669 6171 7171 8171 0.3 5.0 6.3 2 4 10 2343 2583 2823 3063 6172 7172 8172 0.3 5.0 6.3 2 4 5 5070 5270 5470 5670 6173 7173 8173 0.3 5.0 6.3 2 4 10 2344 2584 2824 3064 6174 7174 8174 0.3 5.0 6.3 2 4 20 2345 2585 2825 3065 6175 7175 8175 0.3 5.0 6.3 2 4 5 5071 5271 5471 5671 6176 7176 8176 0.3 5.0 6.3 2 4 10 2346 2586 2826 3066 6177 7177 8177 0.3 5.0 6.3 2 4 5 5072 5272 5472 5672 6178 7178 8178 0.3 5.0 6.3 2 4 10 2347 2587 2827 3067 6179 7179 8179 0.3 5.0 6.3 2 4 20 2348 2588 2828 3068 6180 7180 8180 0.3 5.0 6.3 2 4 5 5073 5273 5473 5673 6181 7181 8181 0.3 5.0 6.3 2 4 10 2349 2589 2829 3069 6182 7182 8182 0.3 5.0 6.3 2 4 5 5074 5274 5474 5674 6183 7183 8183 0.3 5.0 6.3 2 4 10 2350 2590 2830 3070 6184 7184 8184 0.3 5.0 6.3 2 4 20 2351 2591 2831 3071 6185 7185 8185 0.3 5.0 6.3 2 4 5 5075 5275 5475 5675 6186 7186 8186 0.3 5.0 6.3 2 4 10 2352 2592 2832 3072 6187 7187 8187 0.3 5.0 6.3 2 4 5 5076 5276 5476 5676 6188 7188 8188 0.3 5.0 6.3 2 4 10 2353 2593 2833 3073 6189 7189 8189 0.3 5.0 6.3 2 4 20 2354 2594 2834 3074 6190 7190 8190 0.3 5.0 6.3 2 4 5 5077 5277 5477 5677 6191 7191 8191 0.3 5.0 6.3 2 4 10 2355 2595 2835 3075 6192 7192 8192 0.3 5.0 6.3 2 4 5 5078 5278 5478 5678 6193 7193 8193 0.4 8.0 10.0 4 4 10 2356 2596 2836 3076 6194 7194 8194 0.4 8.0 10.0 4 4 20 2357 2597 2837 3077 6195 7195 8195 0.4 8.0 10.0 4 4 5 5079 5279 5479 5679 6196 7196 8196 0.4 9.0 11.0 4 4 10 2358 2598 2838 3078 6197 7197 8197 0.4 9.0 11.0 4 4 5 5080 5280 5480 5680 6198 7198 8198 0.6 12.0 15.0 4 4 10 2359 2599 2839 3079 6199 7199 8199 0.6 12.0 15.0 4 4 20 2360 2600 2840 3080 6200 7200 8200 0.6 12.0 15.0 4 4 5 5081 5281 5481 5681 6201 7201 8201 0.7 14.0 18.0 4 4 10 2361 2601 2841 3081 6202 7202 8202 0.7 14.0 18.0 4 4 5 5082 5282 5482 5682 6203 7203 8203 0.8 17.0 22.0 4 4 10 2362 2602 2842 3082 6204 7204 8204 0.8 17.0 22.0 4 4 20 2363 2603 2843 3083 6205 7205 8205 0.8 17.0 22.0 4 4 5 5083 5283 5483 5683 6206 7206 8206 1.0 20.0 25.0 4 4 10 2364 2604 2844 3084 6207 7207 8207 1.0 20.0 25.0 4 4 5 5084 5284 5484 5684 6208 7208 8208 1.2 25.0 32.0 4 4 10 2365 2605 2845 3085 6209 7209 8209 1.2 25.0 32.0 4 4 For technical questions, contact: tantalum@vishay.com www.vishay.com 43 M39003/01/03/09 Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 STANDARD RATINGS: CSR13, M39003/01-XXXX CAPACITANCE CASE (µF) CODE 3.3 3.9 3.9 4.7 4.7 4.7 5.6 5.6 6.8 6.8 6.8 8.2 8.2 10.0 10.0 10.0 12.0 12.0 15.0 15.0 15.0 18.0 18.0 22.0 22.0 22.0 B B B B B B C C C C C C C C C C C C C C C C C D D D 0.1 0.1 0.1 0.12 0.12 0.15 0.15 0.15 0.18 0.18 0.22 0.22 0.22 0.27 0.27 0.33 0.33 0.33 0.39 0.39 0.47 0.47 0.47 0.56 0.56 A A A A A A A A A A A A A A A A A A A A A A A A A www.vishay.com 44 CAP. TOL. (± %) PART NO. M39003/01FAILURE RATE LEVEL (%/1000 h) MAX. DCL (µA) AT MAX. DF (%) AT - 55 °C + 85 °C M P R S B C D + 25 °C + 85 °C + 125 °C + 25 °C + 125 °C 1.0 0.1 0.01 0.001 0.1 0.01 0.001 50 WVDC AT + 85 °C, SURGE = 65 V . . . 33 WVDC AT + 125 °C, SURGE = 40 V 20 2366 2606 2846 3086 6210 7210 8210 1.2 25.0 32.0 4 4 5 5085 5285 5485 5685 6211 7211 8211 1.5 30.0 38.0 4 4 10 2367 2607 2847 3087 6212 7212 8212 1.5 30.0 38.0 4 4 5 5086 5286 5486 5686 6213 7213 8213 1.7 35.0 44.0 4 4 10 2368 2608 2848 3088 6214 7214 8214 1.7 35.0 44.0 4 4 20 2369 2609 2849 3089 6215 7215 8215 1.7 35.0 44.0 4 4 5 5087 5287 5487 5687 6216 7216 8216 2.2 45.0 56.0 4 4 10 2370 2610 2850 3090 6217 7217 8217 2.2 45.0 56.0 4 4 5 5088 5288 5488 5688 6218 7218 8218 2.2 45.0 56.0 6 6 10 2371 2611 2851 3091 6219 7219 8219 2.2 45.0 56.0 6 6 20 2372 2612 2852 3092 6220 7220 8220 2.2 45.0 56.0 6 6 5 5089 5289 5489 5689 6221 7221 8221 2.5 50.0 63.0 6 6 10 2373 2613 2853 3093 6222 7222 8222 2.5 50.0 63.0 6 6 5 5090 5290 5490 5690 6223 7223 8223 2.5 50.0 63.0 6 6 10 2374 2614 2854 3094 6224 7224 8224 2.5 50.0 63.0 6 6 20 2375 2615 2855 3095 6225 7225 8225 2.5 50.0 63.0 6 6 5 5091 5291 5491 5691 6226 7226 8226 3.0 60.0 75.0 6 6 10 2376 2616 2856 3096 6227 7227 8227 3.0 60.0 75.0 6 6 5 5092 5292 5492 5692 6228 7228 8228 4.0 80.0 100.0 6 6 10 2377 2617 2857 3097 6229 7229 8229 4.0 80.0 100.0 6 6 20 2378 2618 2858 3098 6230 7230 8230 4.0 80.0 100.0 6 6 5 5093 5293 5493 5693 6231 7231 8231 4.5 90.0 113.0 6 6 10 2379 2619 2859 3099 6232 7232 8232 4.5 90.0 113.0 6 6 5 5094 5294 5494 5694 6233 7233 8233 5.5 110.0 138.0 6 6 10 2380 2620 2860 3100 6234 7234 8234 5.5 110.0 138.0 6 6 20 2381 2621 2861 3101 6235 7235 8235 5.5 110.0 138.0 6 6 75 WVDC AT + 85 °C, SURGE = 98 V . . . 50 WVDC AT + 125 °C, SURGE = 64 V 5 5095 5295 5495 5695 6236 7236 8236 0.3 5.0 6.3 2 4 10 2382 2622 2862 3102 6237 7237 8237 0.3 5.0 6.3 2 4 20 2383 2623 2863 3103 6238 7238 8238 0.3 5.0 6.3 2 4 5 5096 5296 5496 5696 6239 7239 8239 0.3 5.0 6.3 2 4 10 2384 2624 2864 3104 6240 7240 8240 0.3 5.0 6.3 2 4 5 5097 5297 5497 5697 6241 7241 8241 0.3 5.0 6.3 2 4 10 2385 2625 2865 3105 6242 7242 8242 0.3 5.0 6.3 2 4 20 2386 2626 2866 3106 6243 7243 8243 0.3 5.0 6.3 2 4 5 5098 5298 5498 5698 6244 7244 8244 0.3 5.0 6.3 2 4 10 2387 2627 2867 3107 6245 7245 8245 0.3 5.0 6.3 2 4 5 5099 5299 5499 5699 6246 7246 8246 0.3 5.0 6.3 2 4 10 2388 2628 2868 3108 6247 7247 8247 0.3 5.0 6.3 2 4 20 2389 2629 2869 3109 6248 7248 8248 0.3 5.0 6.3 2 4 5 5100 5300 5500 5700 6249 7249 8249 0.3 5.0 6.3 2 4 10 2390 2630 2870 3110 6250 7250 8250 0.3 5.0 6.3 2 4 5 5101 5301 5501 5701 6251 7251 8251 0.3 5.0 6.3 2 4 10 2391 2631 2871 3111 6252 7252 8252 0.3 5.0 6.3 2 4 20 2392 2632 2872 3112 6253 7253 8253 0.3 5.0 6.3 2 4 5 5102 5302 5502 5702 6254 7254 8254 0.3 5.0 6.3 2 4 10 2393 2633 2873 3113 6255 7255 8255 0.3 5.0 6.3 2 4 5 5103 5303 5503 5703 6256 7256 8256 0.3 5.0 6.3 2 4 10 2394 2634 2874 3114 6257 7257 8257 0.3 5.0 6.3 2 4 20 2395 2635 2875 3115 6258 7258 8258 0.3 5.0 6.3 2 4 5 5104 5304 5504 5704 6259 7259 8259 0.3 5.0 6.3 2 4 10 2396 2636 2876 3116 6260 7260 8260 0.3 5.0 6.3 2 4 For technical questions, contact: tantalum@vishay.com Document Number: 40018 Revision: 20-Nov-07 M39003/01/03/09 Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 Vishay Sprague STANDARD RATINGS: CSR13, M39003/01-XXXX CAPACITANCE CASE (µF) CODE CAP. TOL. (± %) PART NO. M39003/01FAILURE RATE LEVEL (%/1000 h) M 1.0 P 0.1 R 0.01 S 0.001 B 0.1 C 0.01 MAX. DCL (µA) AT MAX. DF (%) AT - 55 °C + 85 °C D + 25 °C + 85 °C + 125 °C + 25 °C + 125 °C 0.001 75 WVDC AT + 85 °C, SURGE = 98 V . . . 50 WVDC AT + 125 °C, SURGE = 64 V 5 5105 5305 5505 5705 6261 7261 8261 0.3 5.0 0.68 A 6.3 2 4 0.68 A 10 2397 2637 2877 3117 6262 7262 8262 0.3 5.0 6.3 2 4 0.68 A 20 2398 2638 2878 3118 6263 7263 8263 0.3 5.0 6.3 2 4 0.82 B 5 5106 5306 5506 5706 6264 7264 8264 0.3 5.0 6.3 2 4 0.82 B 10 2399 2879 2879 3119 6265 7265 8265 0.3 5.0 6.3 2 4 1.0 B 5 5107 5307 5507 5707 6266 7266 8266 0.3 5.0 6.3 2 4 1.0 B 10 2400 2410 2880 3120 6267 7267 8267 0.3 5.0 6.3 2 4 1.0 B 20 2401 2641 2881 3121 6268 7268 8268 0.3 5.0 6.3 2 4 1.2 B 5 5108 5308 5508 5708 6269 7269 8269 0.3 5.0 6.3 4 4 1.2 B 10 2402 2642 2882 3122 6270 7270 8270 0.3 5.0 6.3 4 4 1.5 B 5 5109 5309 5509 5709 6271 7271 8271 0.6 10.0 13.0 4 4 1.5 B 10 2403 2643 2883 3123 6272 7272 8272 0.6 10.0 13.0 4 4 1.5 B 20 2404 2664 2884 3124 6273 7273 8273 0.6 10.0 13.0 4 4 1.8 B 5 5110 5310 5510 5710 6274 7274 8274 0.7 10.0 13.0 4 4 1.8 B 10 2405 2645 2885 3125 6275 7275 8275 0.7 10.0 13.0 4 4 1.8 B 10 2405 2645 2885 3125 6275 7275 8275 0.7 10.0 13.0 4 4 2.2 B 5 5111 5311 5511 5711 6276 7276 8276 0.8 15.0 19.0 4 4 2.2 B 10 2406 2646 2886 3126 6277 7277 8277 0.8 15.0 19.0 4 4 2.2 B 20 2407 2647 2887 3127 6278 7278 8278 1.0 15.0 19.0 4 4 2.7 B 5 5112 5312 5512 5712 6279 7279 8279 1.0 15.0 19.0 4 4 2.7 B 10 2408 2648 2888 3128 6280 7280 8280 1.2 15.0 19.0 4 4 3.3 B 5 5113 5313 5513 5713 6281 7281 8281 1.2 20.0 25.0 4 4 3.3 B 10 2409 2649 2889 3129 6282 7282 8282 1.2 20.0 25.0 4 4 3.3 B 20 2410 2650 2890 3130 6283 7283 8283 1.5 20.0 25.0 4 4 3.9 B 5 5114 5314 5514 5714 6284 7284 8284 1.5 20.0 25.0 4 4 3.9 B 10 2411 2651 2891 3131 6285 7285 8285 3.0 20.0 25.0 4 4 4.7 C 5 5115 5315 5515 5715 6286 7286 8286 3.0 60.0 75.0 4 4 4.7 C 10 2412 2652 2892 3132 6287 7287 8287 3.0 60.0 75.0 4 4 4.7 C 20 2413 2653 2893 3133 6288 7288 8288 3.0 60.0 75.0 4 4 5.6 C 5 5116 5316 5513 5716 6289 7289 8289 3.0 60.0 75.0 4 4 5.6 C 10 2414 2654 2894 3134 6290 7290 8290 5.0 60.0 75.0 4 4 6.8 C 5 5117 5317 5517 5717 6291 7291 8291 5.0 100.0 125.0 6 6 6.8 C 10 2415 2655 2895 3135 6292 7292 8292 5.0 100.0 125.0 6 6 6.8 C 20 2416 2656 2896 3136 6293 7293 8293 5.0 100.0 125.0 6 6 8.2 C 5 5118 5318 5518 5718 6294 7294 8294 5.0 100.0 125.0 6 6 8.2 C 10 2417 2657 2897 3137 6295 7295 8295 5.0 100.0 125.0 6 6 10.0 C 5 5119 5319 5519 5719 6296 7296 8296 5.0 100.0 125.0 6 6 10.0 C 10 2418 2658 2898 3138 6297 7297 8297 5.0 100.0 125.0 6 6 10.0 C 20 2419 2659 2899 3139 6298 7298 8295 5.0 100.0 125.0 6 6 12.0 D 5 5120 5320 5520 5720 6299 7299 8299 5.0 100.0 125.0 6 6 12.0 D 10 2420 2660 2900 3140 6300 7300 8300 5.0 100.0 125.0 6 6 15.0 D 5 5121 5321 5521 5721 6301 7301 8301 7.0 140.0 175.0 6 6 15.0 D 10 2421 2661 2901 3141 6302 7302 8302 7.0 140.0 175.0 6 6 15.0 D 20 2422 2662 2902 3142 6303 7303 8303 7.0 140.0 175.0 6 6 Document Number: 40018 Revision: 20-Nov-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 45 M39003/01/03/09 Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 Vishay Sprague STANDARD RATINGS: CSR13, M39003/01-XXXX CAPACITANCE CASE (µF) CODE CAP. TOL. (± %) PART NO. M39003/01FAILURE RATE LEVEL (%/1000 h) M 1.0 P 0.1 R 0.01 S 0.001 B 0.1 C 0.01 MAX. DCL (µA) AT MAX. DF (%) AT - 55 °C + 85 °C D + 25 °C + 85 °C + 125 °C + 25 °C + 125 °C 0.001 100 WVDC AT + 85 °C, SURGE = 130 V . . . 67 WVDC AT + 125 °C, SURGE = 86 V 0.056 A 5 5135 5335 5535 5735 6337 7337 8337 0.3 5.0 6.3 2 4 0.056 A 10 2443 2683 2923 3163 6338 7338 8338 0.3 5.0 6.3 2 4 0.068 A 5 5136 5336 5536 5736 6339 7339 8339 0.3 5.0 6.3 2 4 0.068 A 10 2444 2684 2924 3164 6340 7340 8340 0.3 5.0 6.3 2 4 0.068 A 20 2445 2685 2925 3165 6341 7341 8341 0.3 5.0 6.3 2 4 0.082 A 5 5137 5337 5537 5737 6342 7342 8342 0.3 5.0 6.3 2 4 0.082 A 10 2446 2686 2926 3166 6343 7343 8343 0.3 5.0 6.3 2 4 0.1 A 5 5138 5338 5538 5738 6344 7344 8344 0.3 5.0 6.3 2 4 0.1 A 10 2447 2687 2927 3167 6345 7345 8345 0.3 5.0 6.3 2 4 0.1 A 20 2448 2688 2928 3168 6346 7346 8346 0.3 5.0 6.3 2 4 0.12 A 5 5139 5339 5539 5739 6347 7347 8347 0.3 5.0 6.3 2 4 0.12 A 10 2449 2689 2929 3169 6348 7348 8348 0.3 5.0 6.3 2 4 0.15 A 5 5140 5340 5540 5740 6349 7349 8349 0.3 5.0 6.3 2 4 0.15 A 10 2450 2690 2930 3170 6350 7350 8350 0.3 5.0 6.3 2 4 0.15 A 20 2451 2691 2931 3171 6351 7351 8351 0.3 5.0 6.3 2 4 0.18 A 5 5141 5341 5541 5741 6352 7352 8352 0.3 5.0 6.3 2 4 0.18 A 10 2452 2692 2932 3172 6353 7353 8353 0.3 5.0 6.3 2 4 0.22 A 5 5142 5342 5542 5742 6354 7354 8354 0.3 5.0 6.3 2 4 0.22 A 10 2453 2693 2933 3173 6355 7355 8355 0.3 5.0 6.3 2 4 0.22 A 20 2454 2694 2934 3174 6356 7356 8356 0.3 5.0 6.3 2 4 0.27 A 5 5143 5343 5543 5743 6357 7357 8357 0.3 5.0 6.3 2 4 0.27 A 10 2455 2695 2935 3175 6358 7358 8358 0.3 5.0 6.3 2 4 0.33 A 5 5144 5344 5544 5744 6359 7359 8359 0.3 5.0 6.3 2 4 0.33 A 10 2456 2696 2936 3176 6360 7360 8360 0.3 5.0 6.3 2 4 0.33 A 20 2457 2697 2937 3177 6361 7361 8361 0.3 5.0 6.3 2 4 0.39 A 5 5145 5345 5545 5745 6362 7362 8362 0.3 5.0 6.3 2 4 0.39 A 10 2458 2698 2938 3178 6363 7363 8363 0.3 5.0 6.3 2 4 0.47 A 5 5146 5436 5546 5746 6364 7364 8364 0.3 5.0 6.3 2 4 0.47 A 10 2459 2699 2939 3179 6365 7365 8365 0.3 5.0 6.3 2 4 0.47 A 20 2460 2700 2940 3180 6366 7366 8366 0.3 5.0 6.3 2 4 0.56 A 5 5147 5347 5547 5747 6367 7367 8367 0.3 5.0 6.3 2 4 0.56 A 10 2461 2701 2941 3181 6368 7368 8368 0.3 5.0 6.3 2 4 0.68 B 5 5148 5348 5548 5748 6369 7369 8369 0.3 5.0 6.3 2 4 0.68 B 10 2462 2702 2942 3182 6370 7370 8370 0.3 5.0 6.3 2 4 0.68 B 20 2463 2703 2943 3183 6371 7371 8371 0.3 5.0 6.3 2 4 0.82 B 5 5149 5349 5549 5749 6372 7372 8372 0.4 5.0 6.3 2 4 0.82 B 10 2464 2704 2944 3184 6373 7373 8373 0.4 5.0 6.3 2 4 www.vishay.com 46 For technical questions, contact: tantalum@vishay.com Document Number: 40018 Revision: 20-Nov-07 M39003/01/03/09 Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 Vishay Sprague STANDARD RATINGS: CSR13, M39003/01-XXXX CAPACITANCE CASE (µF) CODE CAP. TOL. (± %) PART NO. M39003/01FAILURE RATE LEVEL (%/1000 h) M 1.0 P 0.1 R 0.01 S 0.001 B 0.1 C 0.01 MAX. DCL (µA) AT MAX. DF (%) AT - 55 °C + 85 °C D + 25 °C + 85 °C + 125 °C + 25 °C + 125 °C 0.001 100 WVDC AT + 85 °C, SURGE = 130 V . . . 67 WVDC AT + 125 °C, SURGE = 86 V 1.0 B 5 5150 5350 5550 5750 6374 7374 8374 0.5 5.0 6.3 2 4 1.0 B 10 2465 2705 2945 3185 6375 7375 8375 0.5 5.0 6.3 2 4 1.0 B 20 2466 2706 2946 3186 6376 7376 8376 0.5 5.0 6.3 2 4 1.2 B 5 5151 5351 5551 5751 6377 7377 8377 0.5 5.0 6.3 4 4 1.2 B 10 2467 2707 2947 3187 6378 7378 8378 0.5 5.0 6.3 4 4 1.5 B 5 5152 5352 5552 5752 6379 7379 8379 0.7 10.0 13.0 4 4 1.5 B 10 2468 2708 2948 3188 6380 7380 8380 0.7 10.0 13.0 4 4 1.5 B 20 2469 2709 2949 3189 6381 7381 8381 0.7 10.0 13.0 4 4 1.8 B 5 5153 5353 5553 5753 6382 7382 8382 0.7 10.0 13.0 4 4 1.8 B 10 2470 2710 2950 3190 6383 7383 8383 0.7 10.0 13.0 4 4 2.2 B 5 5154 5354 5554 5754 6384 7384 8384 0.9 15.0 19.0 4 4 2.2 B 10 2471 2711 2951 3191 6385 7385 8385 0.9 15.0 19.0 4 4 2.2 B 20 2472 2712 2952 3192 6386 7386 8386 0.9 15.0 19.0 4 4 2.7 B 5 5155 5355 5555 5755 6387 7387 8387 1.1 15.0 19.0 4 4 2.7 B 10 2473 2713 2953 3193 6388 7388 8388 1.1 15.0 19.0 4 4 3.3 C 5 5156 5356 5556 5756 6389 7389 8389 1.5 30.0 38.0 6 6 3.3 C 10 5157 5357 5557 5757 6390 7390 8390 1.5 30.0 38.0 6 6 3.3 C 20 5158 5358 5558 5758 6391 7391 8391 1.5 30.0 38.0 6 6 3.9 C 5 5159 5359 5559 5759 6392 7392 8392 1.5 30.0 38.0 6 6 3.9 C 10 5160 5360 5560 5760 6393 7393 8393 1.5 30.0 38.0 6 6 4.7 C 5 5161 5361 5561 5761 6394 7394 8394 2.5 50.0 63.0 6 6 4.7 C 10 5162 5362 5562 5762 6395 7395 8395 2.5 50.0 63.0 6 6 4.7 C 20 5163 5363 5563 5763 6396 7396 8396 2.5 50.0 63.0 6 6 5.6 C 5 5164 5364 5564 5764 6397 7397 8397 2.5 50.0 63.0 6 6 5.6 C 10 5165 5365 5565 5765 6398 7398 8398 2.5 50.0 63.0 6 6 6.8 C 5 5166 5366 5566 5766 6399 7399 8399 2.5 50.0 63.0 6 6 6.8 C 10 5167 5367 5567 5767 6400 7400 8400 2.5 50.0 63.0 6 6 6.8 C 20 5168 5368 5568 5768 6401 7401 8401 2.5 50.0 63.0 6 6 Document Number: 40018 Revision: 20-Nov-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 47 M39003/01/03/09 Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 Vishay Sprague STANDARD RATINGS: CSR21, M39003/09-XXXX PART NO. M39003/09FAILURE RATE LEVEL (%/1000 h) CAP. CAPACITANCE CASE TOL. (µF) CODE (± %) 150.0 150.0 150.0 180.0 180.0 270.0 270.0 330.0 330.0 330.0 C C C C C D D D D D 82.0 82.0 100.0 100.0 100.0 120.0 120.0 180.0 180.0 220.0 220.0 220.0 C C C C C C C D D D D D 56.0 56.0 68.0 68.0 68.0 120.0 120.0 150.0 150.0 150.0 C C C C C D D D D D 27.0 27.0 33.0 33.0 33.0 39.0 39.0 47.0 47.0 47.0 56.0 56.0 C C C C C C C C C C D D www.vishay.com 48 MAX. MAX. DF AT ESR AT + 25 °C + 25 °C 1 kHz 100 kHz (%) (Ω) + 25 °C + 85 °C + 125 °C MAX. DCL (µA) AT M P R S B C D 1.0 0.1 0.01 0.001 0.1 0.01 0.001 6 WVDC AT + 85 °C, SURGE = 8 V . . . 4 WVDC AT + 125 °C, SURGE = 5 V 5 0001 0101 0201 0301 2001 3001 4001 4.5 90.0 113.0 10 10 0002 0102 0202 0302 2002 3002 4002 4.5 90.0 113.0 10 20 0003 0103 0203 0303 2003 3003 4003 4.5 90.0 113.0 10 5 0004 0104 0204 0304 2004 3004 4004 5.5 110.0 138.0 10 10 0005 0105 0205 0305 2005 3005 4005 5.5 110.0 138.0 10 5 0006 0106 0206 0306 2006 3006 4006 6.5 130.0 163.0 10 10 0007 0107 0207 0307 2007 3007 4007 6.5 130.0 163.0 10 5 0008 0108 0208 0308 2008 3008 4008 7.5 150.0 188.0 12 10 0009 0109 0209 0309 2009 3009 4009 7.5 150.0 188.0 12 20 0010 0110 0210 0310 2010 3010 4010 7.5 150.0 188.0 12 10 WVDC AT + 85 °C, SURGE = 13 V . . . 7 WVDC AT + 125 °C, SURGE = 9 V 5 0011 0111 0211 0311 2011 3011 4011 4.0 80.0 100.0 8 10 0012 0112 0212 0312 2012 3012 4012 4.0 80.0 100.0 8 5 0013 0113 0213 0313 2013 3013 4013 5.0 100.0 125.0 8 10 0014 0114 0214 0314 2014 3014 4014 5.0 100.0 125.0 8 20 0015 0115 0215 0315 2015 3015 4015 5.0 100.0 125.0 8 5 0016 0116 0216 0136 2016 3016 4016 6.0 120.0 150.0 8 10 0017 0117 0217 0317 2017 3017 4017 6.0 120.0 150.0 8 5 0018 0118 0218 0318 2018 3018 4018 9.0 180.0 226.0 8 10 0019 0119 0219 0319 2019 3019 4019 9.0 180.0 226.0 8 5 0020 0120 0220 0320 2020 3020 4020 10.0 200.0 250.0 10 10 0021 0121 0221 0321 2021 3021 4021 10.0 200.0 250.0 10 20 0022 0122 0222 0322 2022 3022 4022 10.0 200.0 250.0 10 15 WVDC AT + 85 °C, SURGE = 20 V . . . 10 WVDC AT + 125 °C, SURGE = 12 V 5 0023 0123 0223 0323 2023 3023 4023 4.0 80.0 100.0 6 10 0024 0124 0224 0324 2024 3024 4024 4.0 80.0 100.0 6 5 0025 0125 0225 0325 2025 3025 4025 5.0 100.0 125.0 6 10 0026 0126 0226 0326 2026 3026 4026 5.0 100.0 125.0 6 20 0027 0127 0227 0327 2027 3027 4027 5.0 100.0 125.0 6 5 0028 0128 0228 0328 2028 3028 4028 9.0 180.0 226.0 8 10 0029 0129 0229 0329 2029 3029 4029 9.0 180.0 226.0 8 5 0030 0130 0230 0330 2030 3030 4030 10.0 200.0 250.0 8 10 0031 0131 0231 0331 2031 3031 4031 10.0 200.0 250.0 8 20 0032 0132 0232 0332 2032 3032 4032 10.0 200.0 250.0 8 20 WVDC AT + 85 °C, SURGE = 26 V . . . 13 WVDC AT + 125 °C, SURGE = 16 V 5 0033 0133 0233 0333 2033 3033 4033 2.5 50.0 63.0 5 10 0034 0134 0234 0334 2034 3034 4034 2.5 50.0 63.0 5 5 0035 0135 0235 0335 2035 3035 4035 3.5 70.0 88.0 5 10 0036 0136 0236 0336 2036 3036 4036 3.5 70.0 88.0 5 20 0037 0137 0237 0337 2037 3037 4037 3.5 70.0 88.0 5 5 0038 0138 0238 0338 2038 3038 4038 4.0 80.0 100.0 5 10 0039 0139 0239 0339 2039 3039 4039 4.0 80.0 100.0 5 5 0040 0140 0240 0340 2040 3040 4040 4.5 90.0 113.0 6 10 0041 0141 0241 0341 2041 3041 4041 4.5 90.0 113.0 6 20 0042 0142 0242 0342 2042 3042 4042 4.5 90.0 113.0 6 5 0043 0143 0243 0343 2043 3043 4043 5.5 110.0 138.0 6 10 0044 0144 0244 0344 2044 3044 4044 5.5 110.0 138.0 6 For technical questions, contact: tantalum@vishay.com DERATED MAX. RIPPLE CURRENT AT + 25 °C (A) 40 kHz 1 kHz 0.065 0.065 0.065 0.060 0.060 0.050 0.050 0.045 0.045 0.045 3.3 3.3 3.3 3.4 3.4 4.1 4.1 4.3 4.3 4.3 2.0 2.0 2.0 2.4 2.4 3.4 3.4 3.8 3.8 3.8 0.085 0.085 0.075 0.075 0.075 0.070 0.070 0.060 0.060 0.055 0.055 0.055 2.9 2.9 3.0 3.0 3.0 3.2 3.2 3.7 3.7 3.9 3.9 3.9 1.8 1.8 2.2 2.2 2.2 2.5 2.5 3.4 3.4 3.4 3.4 3.4 0.100 0.100 0.095 0.095 0.095 0.070 0.070 0.065 0.065 0.065 2.6 2.6 2.7 2.7 2.7 3.5 3.5 3.6 3.6 3.6 1.8 1.8 2.2 2.2 2.2 2.8 2.8 3.1 3.1 3.1 0.145 0.145 0.130 0.130 0.130 0.120 0.120 0.110 0.110 0.110 0.100 0.100 2.2 2.2 2.3 2.3 2.3 2.4 2.4 2.5 2.5 2.5 2.9 2.9 1.2 1.2 1.4 1.4 1.4 1.7 1.7 1.8 1.8 1.8 2.2 2.2 Document Number: 40018 Revision: 20-Nov-07 M39003/01/03/09 Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 Vishay Sprague STANDARD RATINGS: CSR21, M39003/09-XXXX DERATED MAX. RIPPLE CURRENT MAX. DF MAX. AT + 25 °C PART NO. M39003/09MAX. DCL ESR AT AT (A) FAILURE RATE LEVEL (%/1000 h) (µA) AT + 25 °C + 25 °C CAP. 1 kHz 100 kHz CAPACITANCE CASE TOL. M P R S B C D + 25 °C + 85 °C + 125 °C 40 kHz 1 kHz (Ω) (%) (µF) CODE (± %) 1.0 0.1 0.01 0.001 0.1 0.01 0.001 20 WVDC AT + 85 °C, SURGE = 26 V . . . 13 WVDC AT + 125 °C, SURGE = 16 V 68.0 D 5 0045 0145 0245 0345 2045 3045 4045 7.0 140.0 175.0 6 0.095 3.0 2.4 68.0 D 10 0046 0146 0246 0346 2046 3046 4046 7.0 140.0 175.0 6 0.095 3.0 2.4 68.0 D 20 0047 0147 0247 0347 2047 3047 4047 7.0 140.0 175.0 6 0.095 3.0 2.4 82.0 D 5 0048 0148 0248 0348 2048 3048 4048 8.0 160.0 200.0 6 0.085 3.1 2.5 82.0 D 10 0049 0149 0249 0349 2049 3049 4049 8.0 160.0 200.0 6 0.085 3.1 2.5 100.0 D 5 0050 0150 0250 0350 2050 3050 4050 10.0 200.0 250.0 8 0.075 3.3 2.5 100.0 D 10 0051 0151 0251 0351 2051 3051 4051 10.0 200.0 250.0 8 0.075 3.3 2.5 100.0 D 20 0052 0152 0252 0352 2052 3052 4052 10.0 200.0 250.0 8 0.075 3.3 2.5 35 WVDC AT + 85 °C, SURGE = 46 V . . . 23 WVDC AT + 125 °C, SURGE = 28 V 22.0 C 5 0053 0153 0253 0353 2053 3053 4053 4.0 80.0 100.0 4 0.160 2.1 1.5 22.0 C 10 0054 0154 0254 0354 2054 3054 4054 4.0 80.0 100.0 4 0.160 2.1 1.5 22.0 C 20 0055 0155 0255 0355 2055 3055 4055 4.0 80.0 100.0 4 0.160 2.1 1.5 27.0 D 5 0056 0156 0256 0356 2056 3056 4056 4.5 90.0 113.0 4 0.145 2.4 1.9 27.0 D 10 0057 0157 0257 0357 2057 3057 4057 4.5 90.0 113.0 4 0.145 2.4 1.9 33.0 D 5 0058 0158 0258 0358 2058 3058 4058 5.5 110.0 138.0 5 0.130 2.5 1.9 33.0 D 10 0059 0159 0259 0359 2059 3059 4059 5.5 110.0 138.0 5 0.130 2.5 1.9 33.0 D 20 0060 0160 0260 0360 2060 3060 4060 5.5 110.0 138.0 5 0.130 2.5 1.9 39.0 D 5 0061 0161 0261 0361 2061 3061 4061 7.0 140.0 175.0 5 0.120 2.6 2.0 39.0 D 10 0062 0162 0262 0362 2062 3062 4062 7.0 140.0 175.0 5 0.120 2.6 2.0 47.0 D 5 0063 0163 0263 0363 2063 3063 4063 8.0 160.0 200.0 5 0.110 2.7 2.2 47.0 D 10 0064 0164 0264 0364 2064 3064 4064 8.0 160.0 200.0 5 0.110 2.7 2.2 47.0 D 20 0065 0165 0265 0365 2065 3065 4065 8.0 160.0 200.0 5 0.110 2.7 2.2 50 WVDC AT + 85 °C, SURGE = 65 V . . . 33 WVDC AT + 125 °C, SURGE = 40 V 5.6 C 5 0066 0166 0266 0366 2066 3066 4066 2.2 45.0 56.0 3 0.300 1.5 0.6 5.6 C 10 0067 0167 0267 0367 2067 3067 4067 2.2 45.0 56.0 3 0.300 1.5 0.6 6.8 C 5 0068 0168 0268 0368 2068 3068 4068 2.2 45.0 56.0 3 0.275 1.6 0.7 6.8 C 10 0069 0169 0269 0369 2069 3069 4069 2.2 45.0 56.0 3 0.275 1.6 0.7 6.8 C 20 0070 0170 0270 0370 2070 3070 4070 2.2 45.0 56.0 3 0.275 1.6 0.7 8.2 C 5 0071 0171 0271 0371 2071 3071 4071 2.5 50.0 63.0 3 0.250 1.6 0.9 8.2 C 10 0072 0172 0272 0372 2072 3072 4072 2.5 50.0 63.0 3 0.250 1.6 0.9 10.0 C 5 0073 0173 0273 0373 2073 3073 4073 2.5 50.0 63.0 3 0.230 1.7 1.1 10.0 C 10 0074 0174 0274 0374 2074 3074 4074 2.5 50.0 63.0 3 0.230 1.7 1.1 10.0 C 20 0075 0175 0275 0375 2075 3075 4075 2.5 50.0 63.0 3 0.230 1.7 1.1 12.0 C 5 0076 0176 0276 0376 2076 3076 4076 3.0 60.0 75.0 3 0.210 1.8 1.3 12.0 C 10 0077 0177 0277 0377 2077 3077 4077 3.0 60.0 75.0 3 0.210 1.8 1.3 15.0 C 5 0078 0178 0278 0378 2078 3078 4078 4.0 80.0 100.0 3 0.190 1.9 1.4 15.0 C 10 0079 0179 0279 0379 2079 3079 4079 4.0 80.0 100.0 3 0.190 1.9 1.4 15.0 C 20 0080 0180 0280 0380 2080 3080 4080 4.0 80.0 100.0 3 0.190 1.9 1.4 18.0 C 5 0081 0181 0281 0381 2081 3081 4081 4.5 90.0 113.0 4 0.175 2.0 1.4 18.0 C 10 0082 0182 0282 0382 2082 3082 4082 4.5 90.0 113.0 4 0.175 2.0 1.4 22.0 D 5 0083 0183 0283 0383 2083 3083 4083 5.5 110.0 138.0 4 0.160 2.3 1.7 22.0 D 10 0084 0184 0284 0384 2084 3084 4084 5.5 110.0 138.0 4 0.160 2.3 1.7 22.0 D 20 0085 0185 0285 0385 2085 3085 4085 5.5 110.0 138.0 4 0.160 2.3 1.7 Document Number: 40018 Revision: 20-Nov-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 49 M39003/01/03/09 Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 STANDARD RATINGS: CSR23, M39003/03-XXXX CAPACITANCE CASE (µF) CODE 10.0 10.0 12.0 100.0 100.0 330.0 330.0 390.0 470.0 470.0 680.0 680.0 820.0 1000.0 1000.0 A A A B B C C C C C D D D D D 6.8 6.8 8.2 47.0 47.0 56.0 68.0 68.0 82.0 220.0 220.0 270.0 390.0 470.0 470.0 560.0 A A A B B B B B B C C C D D D D 4.7 4.7 5.6 33.0 33.0 39.0 150.0 150.0 180.0 220.0 220.0 270.0 330.0 330.0 A A A B B B C C C D D D D D www.vishay.com 50 CAP. TOL. (± %) PART NO. M39003/03FAILURE RATE LEVEL (%/1000 h) MAX. DCL (µA) AT MAX. DF (%) AT - 55 °C + 85 °C M P R S B C D + 25 °C + 85 °C + 125 °C + 25 °C + 125 °C 1.0 0.1 0.01 0.001 0.1 0.01 0.001 6 WVDC AT + 85 °C, SURGE = 8 V . . . 4 WVDC AT + 125 °C, SURGE = 5 V 10 0101 0201 0301 0401 2001 3001 4001 0.9 9.0 11.0 6 6 20 0102 0202 0302 0402 2002 3002 4002 0.9 9.0 11.0 6 6 10 0103 0203 0303 0403 2003 3003 4003 1.0 10.0 12.5 6 6 10 0104 0204 0304 0404 2004 3004 4004 6.0 60.0 75.0 8 8 20 0105 0205 0305 0405 2005 3005 4005 6.0 60.0 75.0 8 8 10 0106 0206 0306 0406 2006 3006 4006 15.0 150.0 188.0 8 8 20 0107 0207 0307 0407 2007 3007 4007 15.0 150.0 188.0 8 8 10 0108 0208 0308 0408 2008 3008 4008 15.0 150.0 188.0 10 10 10 0109 0209 0309 0409 2009 3009 4009 15.0 150.0 188.0 10 10 20 0110 0210 0310 0410 2010 3010 4010 15.0 150.0 188.0 10 10 10 0111 0211 0311 0411 2011 3011 4011 20.0 200.0 250.0 10 10 20 0112 0212 0312 0412 2012 3012 4012 20.0 200.0 250.0 10 10 10 0113 0213 0313 0413 2013 3013 4013 20.0 200.0 250.0 10 10 10 0114 0214 0314 0414 2014 3014 4014 30.0 300.0 375.0 10 10 20 0115 0215 0315 0415 2015 3015 4015 30.0 300.0 375.0 10 10 10 WVDC AT + 85 °C, SURGE = 13 V . . . 7 WVDC AT + 125 °C, SURGE = 9 V 10 0116 0216 0316 0416 2016 3016 4016 1.0 10.0 12.5 6 6 20 0117 0217 0317 0417 2017 3017 4017 1.0 10.0 12.5 6 6 10 0118 0218 0318 0418 2018 3018 4018 1.2 12.0 15.0 6 6 10 0119 0219 0319 0419 2019 3019 4019 5.0 50.0 63.0 6 6 20 0120 0220 0320 0420 2020 3020 4020 5.0 50.0 63.0 6 6 10 0121 0221 0321 0421 2021 3021 4021 6.0 60.0 75.0 6 6 10 0122 0222 0322 0422 2022 3022 4022 7.0 70.0 88.0 6 6 20 0123 0223 0323 0423 2023 3023 4023 7.0 70.0 88.0 6 6 10 0124 0224 0324 0424 2024 3024 4024 8.0 80.0 100.0 6 6 10 0125 0225 0325 0425 2025 3025 4025 15.0 150.0 188.0 8 8 20 0126 0226 0326 0426 2026 3026 4026 15.0 150.0 188.0 8 8 10 0127 0227 0327 0427 2027 3027 4027 15.0 150.0 188.0 8 8 10 0128 0228 0328 0428 2028 3028 4028 20.0 200.0 250.0 10 10 10 0129 0229 0329 0429 2029 3029 4029 20.0 200.0 250.0 10 10 20 0130 0230 0330 0430 2030 3030 4030 20.0 200.0 250.0 10 10 10 0131 0231 0331 0431 2031 3031 4031 30.0 300.0 375.0 10 10 15 WVDC AT + 85 °C, SURGE = 20 V . . . 10 WVDC AT + 125 °C, SURGE = 12 V 10 0132 0232 0332 0432 2032 3032 4032 1.0 10.0 12.5 4 4 20 0133 0233 0333 0433 2033 3033 4033 1.0 10.0 12.5 4 4 10 0134 0234 0334 0434 2034 3034 4034 1.3 13.0 16.5 4 4 10 0135 0235 0335 0435 2035 3035 4035 6.0 60.0 75.0 6 6 20 0136 0236 0336 0436 2036 3036 4036 6.0 60.0 75.0 6 6 10 0137 0237 0337 0437 2037 3037 4037 6.0 60.0 75.0 6 6 10 0138 0238 0338 0438 2038 3038 4038 15.0 150.0 188.0 8 8 20 0139 0239 0339 0439 2039 3039 4039 15.0 150.0 188.0 8 8 10 0140 0240 0340 0440 2040 3040 4040 15.0 150.0 188.0 8 8 10 0141 0241 0341 0441 2041 3041 4041 20.0 200.0 250.0 8 8 20 0142 0242 0342 0442 2042 3042 4042 20.0 200.0 250.0 8 8 10 0143 0243 0343 0443 2043 3043 4043 20.0 200.0 250.0 8 8 10 0144 0244 0344 0444 2044 3044 4044 20.0 200.0 250.0 8 8 20 0145 0245 0345 0445 2045 3045 4045 20.0 200.0 250.0 8 8 For technical questions, contact: tantalum@vishay.com Document Number: 40018 Revision: 20-Nov-07 M39003/01/03/09 Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 Vishay Sprague STANDARD RATINGS: CSR23, M39003/03-XXXX CAPACITANCE CASE (µF) CODE 2.7 3.3 3.3 3.9 18.0 22.0 22.0 27.0 56.0 68.0 68.0 82.0 100.0 100.0 120.0 150.0 150.0 180.0 A A A A B B B B C C C C C C C D D D 1.8 8.2 10.0 10.0 33.0 33.0 39.0 47.0 47.0 56.0 68.0 68.0 A B B B C C C C C D D D 1.2 1.5 1.5 5.6 6.8 6.8 22.0 22.0 27.0 33.0 33.0 39.0 A A A B B B C C C D D D Document Number: 40018 Revision: 20-Nov-07 CAP. TOL. (± %) PART NO. M39003/03FAILURE RATE LEVEL (%/1000 h) MAX. DCL (µA) AT MAX. DF (%) AT - 55 °C + 85 °C M P R S B C D + 25 °C + 85 °C + 125 °C + 25 °C + 125 °C 1.0 0.1 0.01 0.001 0.1 0.01 0.001 20 WVDC AT + 85 °C, SURGE = 26 V . . . 13 WVDC AT + 125 °C, SURGE = 16 V 10 0146 0246 0346 0446 2046 3046 4046 0.8 8.0 10.0 4 4 10 0147 0247 0347 0447 2047 3047 4047 1.0 10.0 12.5 4 4 20 0148 0248 0348 0448 2048 3048 4048 1.0 10.0 12.5 4 4 10 0149 0249 0349 0449 2049 3049 4049 1.2 12.0 15.0 4 4 10 0150 0250 0350 0450 2050 3050 4050 4.0 40.0 50.0 6 6 10 0151 0251 0351 0451 2051 3051 4051 4.0 40.0 50.0 6 6 20 0152 0252 0352 0452 2052 3052 4052 4.0 40.0 50.0 6 6 10 0153 0253 0353 0453 2053 3053 4053 5.0 50.0 63.0 6 6 10 0154 0254 0354 0454 2054 3054 4054 9.0 90.0 110.0 6 6 10 0155 0255 0355 0455 2055 3055 4055 10.0 100.0 125.0 6 6 20 0156 0256 0356 0456 2056 3056 4056 10.0 100.0 125.0 6 6 10 0157 0257 0357 0457 2057 3057 4057 10.0 100.0 125.0 6 6 10 0158 0258 0358 0458 2058 3058 4058 15.0 150.0 188.0 6 6 20 0159 0259 0359 0459 2059 3059 4059 15.0 150.0 188.0 6 6 10 0160 0260 0360 0460 2060 3060 4060 15.0 150.0 188.0 6 6 10 0161 0261 0361 0461 2061 3061 4061 20.0 200.0 250.0 8 8 20 0162 0262 0362 0462 2062 3062 4062 20.0 200.0 250.0 8 8 10 0163 0263 0363 0463 2063 3063 4063 20.0 200.0 250.0 8 8 35 WVDC AT + 85 °C, SURGE = 46 V . . . 23 WVDC AT + 125 °C, SURGE = 28 V 10 0164 0264 0364 0464 2064 3064 4064 1.0 10.0 12.5 4 4 10 0165 0265 0365 0465 2065 3065 4065 3.5 35.0 44.0 6 6 10 0166 0266 0366 0466 2066 3066 4066 4.0 40.0 50.0 6 6 20 0167 0267 0367 0467 2067 3067 4067 4.0 40.0 50.0 6 6 10 0168 0268 0368 0468 2068 3068 4068 10.0 100.0 125.0 6 6 20 0169 0269 0369 0469 2069 3069 4069 10.0 100.0 125.0 6 6 10 0170 0270 0370 0470 2070 3070 4070 10.0 100.0 125.0 6 6 10 0171 0271 0371 0471 2071 3071 4071 10.0 100.0 125.0 6 6 20 0172 0272 0372 0472 2072 3072 4072 10.0 100.0 125.0 6 6 10 0173 0273 0373 0473 2073 3073 4073 15.0 150.0 188.0 6 6 10 0174 0274 0374 0474 2074 3074 4074 15.0 150.0 188.0 6 6 20 0175 0275 0375 0475 2075 3075 4075 15.0 150.0 188.0 6 6 50 WVDC AT + 85 °C, SURGE = 65 V . . . 33 WVDC AT + 125 °C, SURGE = 40 V 10 0176 0276 0376 0476 2076 3076 4076 0.9 9.0 11.0 4 4 10 0177 0277 0377 0477 2077 3077 4077 1.2 12.0 15.0 4 4 20 0178 0278 0378 0478 2078 3078 4078 1.2 12.0 15.0 4 4 10 0179 0279 0379 0479 2079 3079 4079 4.5 45.0 56.0 4 4 10 0180 0280 0380 0480 2080 3080 4080 4.5 45.0 56.0 6 6 20 0181 0281 0381 0481 2081 3081 4081 4.5 45.0 56.0 6 6 10 0182 0282 0382 0482 2082 3082 4082 10.0 100.0 125.0 6 6 20 0183 0283 0383 0483 2083 3083 4083 10.0 100.0 125.0 6 6 10 0184 0284 0384 0484 2084 3084 4084 10.0 100.0 125.0 6 6 10 0185 0285 0385 0485 2085 3085 4085 10.0 100.0 125.0 6 6 20 0186 0286 0386 0486 2086 3086 4086 10.0 100.0 125.0 6 6 10 0187 0287 0387 0487 2087 3087 4087 10.0 100.0 125.0 6 6 For technical questions, contact: tantalum@vishay.com www.vishay.com 51 M39003/01/03/09 Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 WEIBULL DISTRIBUTION METHOD FOR DETERMINING FAILURE RATE, MIL-PRF-39003 The current issue of Military Specification MIL-PRF-39003 incorporates Weibull distribution techniques as a means for calculating failure rates for solid tantalum capacitors. The exponential failure rates (M, P, R and S) are inactive for new designs. Weibull graded failure rate level “B“ capacitors supersede exponential failure rates M, P, R and S. Increasingly, more stringent quality measurement systems are being used in the electronics industry. AQL sample plans are being replaced by programs measuring component quality in PPM (Parts Per Million). Product quality specifications seemingly approach perfection. Procedures used to calculate PPM quality levels are based on manufacturers in-process controls and final inspection results and by users data at incoming inspection and equipment assembly. Initial quality requirements are only part of a good product specification. Reliability and useful life should be considered as well - to fit the reliability and useful life requirements of end equipment. Reliability is a measure of the expected failure rate during the useful life of the capacitor. When plotted the failure rate follows a characteristic “bathtub“ curve, covering three periods in the typical capacitor life cycle. The bathtub curve shows the early time period called infant failure period, the uniform failure rate period or useful life and a period of increasing failure rate due to wearout. RELIABILITY LIFE CYCLE TYPICAL “BATHTUB“ CURVE WEAROUT PERIOD FAILURE RATE INFANT FAILURE PERIOD USEFUL LIFE PERIOD TIME The Weibull shape parameter beta (β) is shown as less than one (β < 1) during infant mortality, one (β = 1) during the useful life and greater than one (β > 1) during the wearout period. Since Weibull distribution works well on units with a beta less than 1, solid tantalum capacitors can use this method for determining failure rates. Solid tantalum capacitors fail early in life (normally during the aging or burnin cycles) and show a slightly decreasing failure rate with time - however, there is no known wearout failure mode. The processing of solid tantalum capacitors is not “perfectly clean”. Impurities in the tantalum powders along with microscopic dust particles can cause flaws in the dielectric tantalum oxide. These flaws in the dielectric can cause failure sites which are normally found during the in-process aging or burn-in cycles. A very large percentage of failures occur during these burn-ins. Since the worst flaws are www.vishay.com 52 presumed to fail first, we eventually arrive at flaw sizes which are presumably too small to cause further degradation. Weibull states that the failure rate of a component that shows a decreasing failure rate with time can be predicted within a short period of time under accelerated conditions. Accelerated conditions for solid tantalum capacitors can be imposed by means of either voltage or temperature stress. Since temperatures above + 125 °C can cause degradation of the solid manganese dioxide electrolyte, voltage acceleration is performed instead. The Navy's Crane NAD facility completed testing on solid tantalum capacitors from several manufacturers in late 1981. During testing, acceleration factors (A.F.) were derived from life test results and the following formula used: A.F. = 7.034 x 10-9 e (18.7724 Vs/Vr) Vs = Voltage stress Vr = Rated voltage of unit under test The acceleration factors used in MIL-C-39003 are as shown: A.F. Vs/Vr 1.0 1.0 1.1 6.53 1.2 42.7 1.3 279.0 1.4 1824.0 1.5 1.527 11 923.0 FOR EXAMPLE: 20 000.00 If a 15 µF, 20 V part is placed on test for 1 h at + 85 °C and 26 V (Vs/Vr = 1.3), this is equivalent to 279 hours of testing at + 85 °C and 20 V (exponential grading). To explain the Weibull analysis, several formulas must be shown. The basic Weibull formula is as shown: tβ F ( x ) = 1 – e ⎛ -----⎞ ⎝ α⎠ F(x) = Cumulative fraction failed (P) at time (t) t = Actual test time β = Weibull shape parameter (beta) α = Weibull scale parameter (alpha) To calculate Weibull failure rates, special burn-in ovens must be used which will record an actual time to failure for each of the units on test. To perform the test, 100 % of the units (or 500 pieces whichever is less) are placed in the Weibull oven and taken to test conditions (+ 85 °C and voltage stress per the acceleration factors chosen). For lots over 500 pieces, the balance of the lot is placed in a standard burn-in oven at the same Weibull conditions. Failures that occur during the start-up are not used in the calculation. After test conditions are reached (< 5 min), the start time is considered to be t0. A count of good pieces is taken at no later than 15 minutes after t0. This will be the sample size. At least two hours after t0, the number of failures are counted. If no failures occur, the lot must be put back on test and recounted after 10 h. For technical questions, contact: tantalum@vishay.com Document Number: 40018 Revision: 20-Nov-07 M39003/01/03/09 Solid-Electrolyte TANTALEX® Capacitors, Military MIL-PRF-39003 Qualified, Styles CSR13, 21, 23 Vishay Sprague WEIBULL DISTRIBUTION METHOD FOR DETERMINING FAILURE RATE, MIL-PRF-39003 (Cont’d) If no failures occur, the lot can be re-started at a higher stress level only once. If no failures occur at the higher stress level, the lot is not suitable for Weibull analysis. t0 15 min 2 h ≤ t1 ≤ 10 h 40 h After a minimum of 40 h, the failure count is again taken. If no further failures occur, one is added to the count. Failure rate is calculated by the following: Z (t) = [- β 1n (1 - P2)105]/t2 A.F. Where Z(t) = Failure Rate β = Weibull shape parameter (slope of the line between t1 and t2 graphed on paper with a 1n (t) abscissa and 1n 1n (1/(1-P)) ordinate P = Ratio of failures to units on test at stop time t2 = Number of hours on test A.F. = Acceleration Factor The failure rate can be calculated from the previous formula as follows: Z (t) = [- β 1n (1 - P)105]/t A.F. Z (t) = [- 0.2119 1n (1 - 0.0326) 105]/40 (17356) Z (t) = [- 0.2119 (- 0.0331) 105]/6.9424 (105) Z (t) = [0.0070/6.9424] Z (t) = 0.0010 %/1000 h ACTUAL WEIBULL TEST ANALYSIS FOR THE VISHAY SPRAGUE EQUIPMENT Document Number: 40018 Revision: 20-Nov-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 53 CTS1, CTS13, 749DX Vishay Sprague Hermetically Sealed, Axial-Lead, to CECC Specifications FEATURES • Terminations: Tin/lead (SnPb), 100 % Tin (RoHS compliant) • Hermetically sealed metal case with plastic film insulation • • • • Available RoHS* COMPLIANT Extended capacitance range (type 749DX) High operational stability with both time and temperature Low leakage current Low dissipation factor APPLICATIONS Performance and reliability has been proven in a wide range of applications such as: filtering, by-pass, coupling, energy storage, timing circuits. PERFORMANCE CHARACTERISTICS SPECIFICATIONS Operating Temperature: - 55 °C to + 85 °C (types CTS13) - 55 °C to + 125 °C (types CTS1, 749DX) CECC BS 30201-001 30201-002 30201-005 30201-011/012 30201-029 749DX CTS1 CTS13 749DX 749DX 9073-N001 749DX IECQ ORDERING INFORMATION CTS13 TYPE Identifies the Basic Capacitor Design CTS1 = CECC 30201-002 CTS13 = CECC 30201-005 749DX = CECC 30201-001/011/012/029 105 X0 040 CAPACITANCE CAPACITANCE DC VOLTAGE RATING TOLERANCE AT + 85 °C A CASE CODE 2 STYLE NUMBER Expressed in volts. Where necessary, zeros precede the voltage rating to complete the 3 digit block 6R3 = 6.3 V See Table Ratings and Case Codes. 0 = Bare Case 2= Plastic-Film Insulation X0 = ± 20 % X9 = ± 10 % X5 = ± 5 % (Special Order) Expressed in picofarads. First two digits are significant. Third digit is the number of zeros following. P PACKAGING E3 ROHS COMPLIANT See Taping and Packaging E3 = 100 % Tin termination (RoHS compliant) Blank = SnPb termination DIMENSIONS in millimeters 30 MIN. 30 MIN. * L MAX. D MAX. Ød * 23 mm MAX. FOR TAPED CAPACITORS CASE CODE A BS D MAX. 3.6 NF D MAX. 3.8 L MAX. 10.2 + 10 % Ø d - 0.05 0.5 B 4.9 5.1 15.0 0.5 C 7.5 7.7 20.5 0.6 D 9.1 9.3 24.0 0.6 * Pb containing terminations are not RoHS compliant, exemptions may apply www.vishay.com 54 For technical questions, contact: eurotant@vishay.com Document Number: 42073 Revision: 23-Jan-08 CTS1, CTS13, 749DX Hermetically Sealed, Axial-Lead, to CECC Specifications Vishay Sprague TYPE CTS1: STANDARD RATINGS AND CASE CODES RATED VOLTAGE UR (+ 85 °C) CR µF 6.3 V 10 V 16 V 25 V 40 V 50 V 53 V 80 V 100 V 125 V CATEGORY VOLTAGE UC (+ 125 °C) 40 V 50 V 67 V 82 V 0.10 4V 6.3 V 10 V 13 V 25 V 33 V A A A A 0.12 A A A A 0.15 A A A A 0.18 A A A A 0.22 A A A A 0.27 A A A A A 0.33 A A A A A 0.39 0.47 A A A A A B A A A A B 0.56 A A A A A B 0.68 A A A A B B 0.82 A A B B B B 1.0 A A B B B B 1.2 1.5 A A B B B B B B B B B B B 1.8 A B B B B B B 2.2 A B B B B B B 2.7 A B B B B B 3.3 A B B B B C 3.9 A B B B B C 4.7 A B B C C C 5.6 A B C C C C 6.8 A B C C C C 8.2 B C C C C 10 B C C C C 12 B C C D D 15 B C C D D 18 B C C D C D 22 B 27 B C D 33 B C D 39 B C 47 B C 56 B C D C D 68 82 100 120 C 150 C 180 C D C D D D D D D 220 D 270 D 330 D Note: Preferred ratings are in bold characters. Non-preferred ratings are available only with a capacitance tolerance of ± 10 % or ± 5 % (special order). Document Number: 42073 Revision: 23-Jan-08 For technical questions, contact: eurotant@vishay.com www.vishay.com 55 CTS1, CTS13, 749DX Hermetically Sealed, Axial-Lead, to CECC Specifications Vishay Sprague TYPE CTS13: STANDARD RATINGS AND CASE CODES CR µF RATED VOLTAGE UR (+ 85 °C ) 6.3 V 10 V 16 V 20 V 25V 40 V 50 V 63 V 0.10 A A A 0.12 A A A 0.15 A A A 0.18 A A A 0.22 A A A 0.27 A A A 0.33 A A A 0.39 A A A 0.47 A A A 0.56 A A A 0.68 A A A 0.82 A A B 1.0 A A B 1.2 A A B B 1.5 A B B B A B B B A B 1.8 2.2 B B 2.7 A B B B 3.3 A B B B 3.9 A B B B 4.7 A B B C C 5.6 A B C 6.8 A B C C C C C 8.2 B 10 C C C 12 B B C C D 15 B C C D D 18 B C C 22 B C D 27 B C 33 B C 39 B 47 B 56 B C 68 C D C D 100 C D C 150 C 180 D D 82 120 D D C C D D D D 220 D 270 D 330 D Note: Preferred ratings are in bold characters. Non-preferred ratings are available only with a capacitance tolerance of ± 10 % or ± 5 % (special order). www.vishay.com 56 For technical questions, contact: eurotant@vishay.com Document Number: 42073 Revision: 23-Jan-08 CTS1, CTS13, 749DX Hermetically Sealed, Axial-Lead, to CECC Specifications Vishay Sprague TYPE 749DX: STANDARD RATINGS AND CASE CODES CR µF 6.3 V 10 V 16 V RATED VOLTAGE UR ( + 85 °C ) 20 V 25 V 35 V CATEGORY VOLTAGE UC ( + 125 °C ) 13 V 16 V 23 V 40 V 50 V 63 V 4V 6.3 V 10 V 25 V 33 V 40 V 0.068 A 0.085 A 0.10 A A A 0.12 A A A 0.15 A A A 0.18 A A A 0.22 A A A 0.27 A A A 0.33 A A A 0.39 A A A 0.47 A A A 0.56 A A A 0.68 A A A 0.82 A A A B 1.0 A A A B 1.2 A B B B B 1.5 A B B B B 1.8 A B B B B 2.2 A B B B B 2.7 A B B B B 3.3 A B B B B 3.9 A B B B B (1) 4.7 A B B C 5.6 A B B C C (1) (1) 6.8 A C C 8.2 B C C C C 10 B C C C C 12 B C C C D 15 B C C C D 18 B C C C D 22 B C C D 27 B C D D 33 B C D D 39 B C D D 47 B C D (1) 56 B C D 68 C D 82 C D 100 C D 120 C D 150 C D 180 C D 220 D 270 D 330 D Note: (1) See extended range page Preferred ratings are in bold characters. Non-preferred ratings are available only with a capacitance tolerance of ± 10 % or ± 5 % (special order). Document Number: 42073 Revision: 23-Jan-08 For technical questions, contact: eurotant@vishay.com www.vishay.com 57 CTS1, CTS13, 749DX Hermetically Sealed, Axial-Lead, to CECC Specifications Vishay Sprague TYPE 749DX: EXTENDED RATINGS AND CASE CODES RATED VOLTAGE UR ( + 85 °C ) CR µF 6.3 V 10 V 16 V 20 V 25 V 35 V 50 V CATEGORY VOLTAGE UC ( + 125 °C ) 23 V 32 V 1.2 4V 6.3 V 10 V 13 V 16 V A A 1.5 A A 1.8 A 2.2 A 2.7 A 3.3 A 3.9 A A 4.7 A A 5.6 A 6.8 B B A 8.2 A 10 A B B 12 A B 15 A B 18 B 22 B B C 27 B 33 B C D 39 B C D 47 C B C 56 B C D 68 B C D 82 B D 100 B C C D 120 B C C D 150 C 180 C D D D 220 C 270 C D 330 C D D 390 C D 470 C D 560 D D D 680 D 820 D 1000 D Note: Preferred ratings are in bold characters. Non-preferred ratings are available only with a capacitance tolerance of ± 10 % or ± 5 % (special order). www.vishay.com 58 For technical questions, contact: eurotant@vishay.com Document Number: 42073 Revision: 23-Jan-08 CTS1, CTS13, 749DX Hermetically Sealed, Axial-Lead, to CECC Specifications Vishay Sprague TYPICAL CURVES RIPPLE VOLTAGE AT + 25 °C CASE “B” CAPACITORS CASE “A” CAPACITORS 100 100 10 VRMS 1 = 100 V and 125 V 2 = 80 V 3 = 50 V and 63 V 4 = 35 V and 40 V 5 = 20 V and 25 V 6 = 16 V 7 = 10 V 8 = 6.3 V 1 2 3 4 5 6 7 8 5 4 3 2 50 40 30 20 1 0.5 0.4 0.3 0.2 0.5 0.4 0.3 0.2 0.1 0.1 10 100 1K 10K 100K 5 6 7 8 5 4 3 2 1 10 1M 1 = 100 V and 125 V 2 = 80 V 3 = 50 V and 63 V 4 = 35 V and 40 V 5 = 20 V and 25 V 6 = 16 V 7 = 10 V 8 = 6.3 V 1 2 3 4 10 VRMS 50 40 30 20 100 1K 100K 1M FREQUENCY IN Hz FREQUENCY IN Hz CASE “C” CAPACITORS CASE “D” CAPACITORS 100 100 1 = 100 V and 125 V 2 = 80 V 3 = 50 V and 63 V 4 = 35 V and 40 V 5 = 20 V and 25 V 6 = 16 V 7 = 10 V 8 = 6.3 V 1 2 3 4 10 5 6 7 8 5 4 3 2 50 40 30 20 4 5 6 7 5 4 3 2 1 1 0.5 0.4 0.3 0.2 0.5 0.4 0.3 0.2 1 = 80 V 2 = 50 V and 63 V 3 = 35 V and 40 V 4 = 20 V and 25 V 5 = 16 V 6 = 10 V 7 = 6.3 V 1 2 3 10 VRMS 50 40 30 20 VRMS 10K 0.1 0.1 10 100 1K 10K 100K 1M 10 100 FREQUENCY IN Hz Document Number: 42073 Revision: 23-Jan-08 For technical questions, contact: eurotant@vishay.com 1K 10K 100K 1M FREQUENCY IN Hz www.vishay.com 59 CTS1, CTS13, 749DX Hermetically Sealed, Axial-Lead, to CECC Specifications Vishay Sprague PERFORMANCE CHARACTERISTICS 1. Operating Temperature: - 55 °C to + 85 °C with rated DC voltage UR applied, + 85 °C to + 125 °C with linear voltage derating to category voltage UC (only for types CTS1, 749DX). 2. Capacitance and Tolerance: Capacitance measured at 100 Hz and + 25 °C shall be within the specified tolerance limits of the nominal rating. Capacitance measurement shall be made by means of a polarized capacitance bridge. The polarizing voltage shall be of 2.2 V. The maximum voltage applied during measurements shall be 1.0 Vrms at 100 Hz and + 25 °C. 3. Reverse Voltage: These capacitors are capable of withstanding peak voltage in the reverse direction equal to: 15 % of the rated DC voltage at + 25 °C, 5 % of the rated DC voltage at + 85 °C. 4.Surge Voltage: 6. Dissipation factor: The dissipation factor, when measured at 100 Hz, shall not exceed the values below: Table 3 CTS1/CTS13 TEMP. CR ≤ 100 CR > 100 - 55 °C 9% 11 % 8% 10 % + 25 °C 6% 8% 6% 8% + 85 °C 9% 11 % - - 12 % 14 % 10 % 11 % + 125 °C (1) Note: (1) not applicable for CTS13 7. Stability at low and high temperature: Capacitance change with temperature shall not exceed the limits of the following table, leakage current and dissipation factor shall be within the limits specified in Tables 2 and 3. Table 4 TEMPERATURE Table 1 PRODUCT TYPE SURGE VOLTAGE AT + 85 °C SURGE VOLTAGE AT + 125 °C CTS13 1.30 UR - 749DX/CTS1 1.30 UR 1.30 UC Capacitors shall withstand the surge voltage applied in series with a 1000 W resistor, at the rate of 1.5 minute on, 5.5 minute off, for 1000 successive test cycles at + 85 °C or at + 125 °C. After test, dissipation factor and leakage current shall meet the initial requirements at + 25 °C (see below), capacitance change shall not exceed ± 10 % of initial value at + 25 °C. 5. Leakage current: Rated voltage UR shall be applied to capacitors during five minutes with a resistor of 1000 Ω in series with each capacitor, before making DC leakage current measurements. The leakage current shall not exceed the following limits: Table 2 TEMPERATURE CTS1/CTS13/749DX + 25 °C 0.01 CR x UR or 1 µA whichever is greater + 85 °C 0.1 CR x UR or 10 µA whichever is greater + 125 °C 0.125 CR x UR or 12.5 µA whichever is greater www.vishay.com 60 749DX CRUR ≤ 1900 CRUR > 1900 Note: CTS1/CTS13/749DX - 55 °C - 10 % + 85 °C + 12 % + 125 °C (2) + 15 % (2) not applicable for CTS13 8. Impedance: The impedance measured at 100 kHz and 25 °C shall not exceed the following values: Table 5 CASE CODE Z (Ω)(3) A 10 B 5 C 2 D 1 Note: (3) not applicable for CR ≤ 0.68 μF 9. Life test: After 2000 h at + 85 °C with rated DC voltage applied, or after 2000 h at + 125 °C with category DC voltage applied (for types CTS1, 749DX only) capacitors shall meet the requirements in table 6. Table 6 PRODUCT CAPACITANCE TYPE CHANGE CTS1 CTS13 749DX Within ± 10 % of initial value at + 25 °C For technical questions, contact: eurotant@vishay.com DISSIPATION FACTOR DC LEAKAGE CURRENT Within initial requirement at + 25 °C Within 125 % of initial requirements at + 25 °C Document Number: 42073 Revision: 23-Jan-08 CTS1, CTS13, 749DX Hermetically Sealed, Axial-Lead, to CECC Specifications PERFORMANCE CHARACTERISTICS (Continued) 10. Humidity test: After 56 days (1350 h) at + 40 °C, 90 to 95 % of relative humidity (per IEC 68-2-3) with no voltage applied, capacitors shall meet the requirements in table 7 below. Table 7 CAPACITANCE CHANGE Within ± 3 % of initial value DC LEAKAGE CURRENT Within initial requirement at + 25 °C -Table 2 DISSIPATION FACTOR Within initial requirement at + 25 °C - Table 3 Vishay Sprague GUIDE TO APPLICATION 1. A-C Ripple Current: The maximum allowable ripple determined from the formula: I rms = CAPACITANCE CHANGE DC LEAKAGE CURRENT Within initial requirement at + 25 °C - Table 2 DISSIPATION FACTOR Within initial requirement at + 25 °C - Table 3 Typical values of charge-discharge current (per above test conditions). RATED VOLTAGE UR (V) CHARGE-DISCHARGE CURRENT (A) 6.3 13 10 20 16 32 25 50 shall where, P = Power Dissipation in W at + 25 °C as given below RESR = The capacitor Equivalent Series resistance at the specified frequency. 2. A-C Ripple Voltage: The maximum allowable ripple determined from the formula: V rms = voltage shall where, Z= The capacitor Impedance at the specified frequency. The calculations are summarized on the graphs page 59 giving the maximum available ripple voltage as a function of frequency. However, the sum of the peak AC voltage plus the DC voltage shall not exceed the rated DC voltage at + 85 °C of the capacitor. The sum of the negative peak AC voltage plus the DC voltage shall not allow a voltage reversal exceeding 15 % of the rated DC voltage. 3. AC Ripple Current or Voltage Derating Factor: If these capacitors are to be operated at temperatures above + 25° C, the permissible rms ripple current or voltage shall be calculated using the derating factors in the table below: 80 50 100 TEMPERATURE DERATING FACTOR 63 126 + 25 °C 1.0 + 55 °C 0.8 + 85 °C 0.6 + 125 °C 0.4 13. Lead pull test: Leads shall withstand the following test (IEC 68 - 2 - 2): Tensile stress of 5N (cases A and B) or 10N (cases C and D) for 10 s in any direction One bend in each direction Two cosecutive rotations of 180° Document Number: 42073 Revision: 23-Jan-08 be P ----------------- × Z R ESR 40 12. Insulation test: For capacitors with insulating sleeves, a DC voltage of 100 V shall be applied for one minute between the case of the capacitor and a metal “V” block in intimate contact with the insulating sleeve. The insulating resistance measured in these conditions shall be at least 100 MΩ. be P ---------------R ESR Table 8 Within ± 5 % of initial value at + 25 °C current 4. Power Dissipation: Power dissipation will be affected by the heat sinking capability of the mounting surface. Non-sinusoidial ripple current may produce heating effects which differ from those shown in the following table. It is important that the equivalent Irms value be established when calculating permissible operating levels. CASE CODE POWER DISSIPATION AT + 25 °C (W) A 0.115 B 0.145 C 0.185 D 0.225 For technical questions, contact: eurotant@vishay.com www.vishay.com 61 CTS1, CTS13, 749DX Hermetically Sealed, Axial-Lead, to CECC Specifications Vishay Sprague TAPE AND REEL PACKING S MEETS IEC 286-1 1.5 max. L1 - L2 = 1.5 mm max. S = component spacing (cumulative tolerance on 20 units = 4 mm) b = tape spacing c = overall length 0.2 ± 0.3 L1 L2 b c DIMENSIONS in millimeters REEL PACK AMMO PACK CASE SIZE REEL AND AMMO S b c MAX. b c MAX. A 5.0 ± 0.3 63 ± 2 78 53 ± 2 B 5.0 ± 0.3 63 ± 2 78 53 ± 2 C 10.0 ± 0.3 63 ± 2 78 D 10.0 ± 0.3 63 ± 2 78 PACKAGING CODE OPTION P P OPTION R OPTION G BULK QTY PER BOX QTY PER PACK 68 500 100 68 500 75 53 ± 2 68 250 50 53 ± 2 68 250 25 QTY PER REEL b c MAX. 68 1000 53 ± 2 68 1000 53 ± 2 63 ± 2 78 500 63 ± 2 78 500 R G B MARKING Capacitors shall be marked with SPRAGUE and/or the registered trademark 2 at vendor‘s option; the type number; rated capacitance and tolerance (with a letter code, if different from ± 20 %, K = ± 10 % ; J = ± 5 %) ; rated DC voltage at + 85 °C and the date code of manufacture. Capacitors shall be marked on one end with a “plus” sign (+) to identify the positive terminal. www.vishay.com 62 For technical questions, contact: eurotant@vishay.com Document Number: 42073 Revision: 23-Jan-08 Contents CX06 ................................ 64 CX16 ................................ 67 HA .................................... 70 Subminiature Case SHA.................................. 78 TC .................................... 84 STC.................................. 91 CX06 Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors FEATURES • Rectangular case with radial leads • 2 to 35 VDC • 0.1 µF to 220 µF • Operating temperature range: - 55 °C to + 85 °C • Qualified to MIL-PRF-49137 ORDERING INFORMATION CX MODEL 06 LEAD CONFIGURATION A VOLTAGE 474 CAPACITANCE 0 = Radial M CAPACITANCE TOLERANCE M = ± 20 % K = ± 10 % Example: CX06A474M DIMENSIONS in inches [millimeters] RADIAL ANODE IDENTIFICATION PLACED OVER POSITIVE LEAD IN READ OR IN CONTRASTING COLOR T W H M 0.75 [19.5] MIN. (-)(+) 1.00 [25.4] MIN. S CASE CODE T MAX. W MAX. H MAX. M ± 0.002 [± 0.051] S A 0.040 [1.02] 0.050 [1.27] 0.100 [2.54] 0.007 [0.18] 0.030 ± 0.015 [0.76 ± 0.38] B 0.040 [1.02] 0.070 [1.78] 0.125 [3.18] 0.010 [0.25] 0.050 ± 0.015 [1.27 ± 0.38] C 0.070 [1.78] 0.120 [3.05] 0.165 [4.19] 0.010 [0.25] 0.100 ± 0.020 [2.54 ± 0.51] D 0.075 [1.91] 0.185 [4.70] 0.225 [5.72] 0.010 [0.25] 0.150 ± 0.020 [3.81 ± 0.51] E 0.110 [2.79] 0.220 [5.59] 0.290 [7.37] 0.016 [0.41] 0.180 ± 0.025 [4.57 ± 0.64] F 0.130 [3.30] 0.230 [5.84] 0.310 [7.87] 0.016 [0.41] 0.200 ± 0.025 [5.08 ± 0.64] G 0.150 [3.81] 0.375 [9.53] 0.475 [12.07] 0.016 [0.41] 0.300 ± 0.025 [7.62 ± 0.64] www.vishay.com 64 For technical questions, contact: tantalum@vishay.com Document Number: 43007 Revision: 04-Dec-07 CX06 Subminiature, Leaded Solid Tantalum Capacitors Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) MAX. DF (%) 0.47 10 2.2 10 MAX. DCL AT + 25 °C (µA) CASE CODE PART NUMBER 0.5 A CX06A474-(1) 10 0.5 B CX06A225-(1) 10 0.5 C CX06A106-(1) 2 WVDC AT + 85 °C 3 WVDC AT + 85 °C 1.5 10 0.5 B CX06B155-(1) 6.8 10 0.5 C CX06B685-(1) 22 10 1 D CX06B226-(1) 220 15 9 G CX06B227-(1) 0.33 10 0.5 A CX06C334-(1) 1 8 0.5 B CX06C105-(1) 4.7 8 0.5 C CX06C475-(1) 15 8 1 D CX06C156-(1) 47 8 2 E CX06C476-(1) 68 8 3 F CX06C686-(1) 0.22 10 0.5 A CX06D224-(1) 0.68 6 0.5 B CX06D684-(1) 3.3 6 0.5 C CX06D335-(1) 10 6 1 D CX06D106-(1) 33 6 2 E CX06D336-(1) 47 6 3 F CX06D476-(1) 150 10 9 G CX06D157-(1) 0.15 10 0.5 A CX06F154-(1) 0.47 6 0.5 B CX06F474-(1) 2.2 6 0.5 C CX06F225-(1) 6.8 6 1 D CX06F685-(1) 22 6 2 E CX06F226-(1) 33 6 3 F CX06F336-(1) 100 8 9 G CX06F107-(1) 4 WVDC AT + 85 °C 6 WVDC AT + 85 °C 10 WVDC AT + 85 °C 15 WVDC AT + 85 °C 0.10 10 0.5 A CX06H104-(1) 0.33 6 0.5 B CX06H334-(1) 1.5 6 0.5 C CX06H155-(1) 15 6 2 E CX06H156-(1) 22 6 3 F CX06H226-(1) 68 8 9 G CX06H686-(1) Note: (1) Add suffix to indicate capacitance tolerance K = ± 10 % or M = ± 20 % Document Number: 43007 Revision: 04-Dec-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 65 CX06 Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors STANDARD RATINGS CAPACITANCE (µF) MAX. DF (%) MAX. DCL AT + 25 °C (µA) CASE CODE PART NUMBER 20 WVDC AT + 85 °C 0.10 6 0.5 B CX06J104-(1) 0.15 6 0.5 B CX06J154-(1) 0.22 6 0.5 B CX06J224-(1) 1 6 0.5 C CX06J105-(1) 3.3 6 1 D CX06J335-(1) 4.7 6 1 D CX06J475-(1) 10 6 2 E CX06J106-(1) 15 6 3 F CX06J156-(1) 47 8 9 G CX06J476-(1) 25 WVDC AT + 85 °C 0.68 6 0.5 C CX06K684-(1) 2.2 6 1 D CX06K225-(1) 6.8 6 2 E CX06K685-(1) 10 6 3 F CX06K106-(1) 33 6 9 G CX06K336-(1) 35 WVDC AT + 85 °C 0.10 6 0.5 C CX06M104-(1) 0.15 6 0.5 C CX06M154-(1) 0.22 6 0.5 C CX06M224-(1) 0.33 6 0.5 C CX06M334-(1) 0.47 6 0.5 C CX06M474-(1) 0.68 6 1 D CX06M684-(1) 1 6 1 D CX06M105-(1) 1.5 6 1 D CX06M155-(1) 2.2 6 2 E CX06M225-(1) 3.3 6 2 E CX06M335-(1) 4.7 6 2 E CX06M475-(1) 6.8 6 3 F CX06M685-(1) 10 6 9 G CX06M106-(1) 15 6 9 G CX06M156-(1) 22 6 9 G CX06M226-(1) Note: (1) Add suffix to indicate capacitance tolerance K = ± 10 % or M = ± 20 % www.vishay.com 66 For technical questions, contact: tantalum@vishay.com Document Number: 43007 Revision: 04-Dec-07 CX16 Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors FEATURES • Axial leads • 2 to 35 VDC • 0.1 µF to 220 µF • Operating temperature range: - 55 °C to + 85 °C • Qualified to MIL-PRF-49137 ORDERING INFORMATION CX MODEL 06 LEAD CONFIGURATION A VOLTAGE 474 CAPACITANCE M CAPACITANCE TOLERANCE 1 = Axial M = ± 20 % K = ± 10 % Example: CX16A474M DIMENSIONS in inches [millimeters] AXIAL ANODE IDENTIFICATION PLACED OVER POSITIVE LEAD IN RED OR IN CONTRASTING COLOR T W 0.75 [19.05] MIN. (+) H 0.75 [19.05] MIN. (-) M CASE CODE T MAX. W MAX. H MAX. M ± 0.002 [± 0.051] A 0.040 [1.02] 0.050 [1.27] 0.100 [2.54] 0.007 [0.18] B 0.040 [1.02] 0.070 [1.78] 0.125 [3.18] 0.010 [0.25] C 0.070 [1.78] 0.120 [3.05] 0.165 [4.19] 0.010 [0.25] D 0.075 [1.91] 0.185 [4.70] 0.225 [5.72] 0.010 [0.25] E 0.110 [2.79] 0.220 [5.59] 0.290 [7.37] 0.016 [0.41] F 0.130 [3.30] 0.230 [5.84] 0.310 [7.87] 0.016 [0.41] G 0.150 [3.81] 0.375 [9.53] 0.475 [12.07] 0.016 [0.41] Document Number: 43018 Revision: 05-Dec-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 67 CX16 Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors STANDARD RATINGS CAPACITANCE (µF) MAX DF (%) 0.47 10 2.2 10 MAX. DCL AT + 25 °C (µA) CASE CODE PART NUMBER 0.5 A CX16A474-(1) 10 0.5 B CX16A225-(1) 10 0.5 C CX16A106-(1) 2 WVDC AT + 85 °C 3 WVDC AT + 85 °C 1.5 10 0.5 B CX16B155-(1) 6.8 10 0.5 C CX16B685-(1) 22 10 1 D CX16B226-(1) 220 15 9 G CX16B227-(1) 0.33 10 0.5 A CX16C334-(1) 1 8 0.5 B CX16C105-(1) 4.7 8 0.5 C CX16C475-(1) 15 8 1 D CX16C156-(1) 47 8 2 E CX16C476-(1) 68 8 3 F CX16C686-(1) 0.22 10 0.5 A CX16D224-(1) 0.68 6 0.5 B CX16D684-(1) 3.3 6 0.5 C CX16D335-(1) 10 6 1 D CX16D106-(1) 33 6 2 E CX16D336-(1) 47 6 3 F CX16D476-(1) 150 10 9 G CX16D157-(1) 0.15 10 0.5 A CX16F154-(1) 0.47 6 0.5 B CX16F474-(1) 2.2 6 0.5 C CX16F225-(1) 6.8 6 1 D CX16F685-(1) 22 6 2 E CX16F226-(1) 33 6 3 F CX16F336-(1) 100 8 9 G CX16F107-(1) 4 WVDC AT + 85 °C 6 WVDC AT + 85 °C 10 WVDC AT + 85 °C 15 WVDC AT + 85 °C 0.10 10 0.5 A CX16H104-(1) 0.33 6 0.5 B CX16H334-(1) 1.5 6 0.5 C CX16H155-(1) 15 6 2 E CX16H156-(1) 22 6 3 F CX16H226-(1) 68 8 9 G CX16H686-(1) Note: (1) Add suffix to indicate capacitance tolerance K = ± 10 % or M = ± 20 % www.vishay.com 68 For technical questions, contact: tantalum@vishay.com Document Number: 43018 Revision: 05-Dec-07 CX16 Subminiature, Leaded Solid Tantalum Capacitors Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) MAX DF (%) MAX. DCL AT + 25 °C (µA) CASE CODE PART NUMBER 20 WVDC AT + 85 °C 0.10 6 0.5 B CX16J104-(1) 0.15 6 0.5 B CX16J154-(1) 0.22 6 0.5 B CX16J224-(1) 1 6 0.5 C CX16J105-(1) 3.3 6 1 D CX16J335-(1) 4.7 6 1 D CX16J475-(1) 10 6 2 E CX16J106-(1) 15 6 3 F CX16J156-(1) 47 8 9 G CX16J476-(1) 25 WVDC AT + 85 °C 0.68 6 0.5 C CX16K684-(1) 2.2 6 1 D CX16K225-(1) 6.8 6 2 E CX16K685-(1) 10 6 3 F CX16K106-(1) 33 6 9 G CX16K336-(1) 35 WVDC AT + 85 °C 0.10 6 0.5 C CX16M104-(1) 0.15 6 0.5 C CX16M154-(1) 0.22 6 0.5 C CX16M224-(1) 0.33 6 0.5 C CX16M334-(1) 0.47 6 0.5 C CX16M474-(1) 0.68 6 1 D CX16M684-(1) 1 6 1 D CX16M105-(1) 1.5 6 1 D CX16M155-(1) 2.2 6 2 E CX16M225-(1) 3.3 6 2 E CX16M335-(1) 4.7 6 2 E CX16M475-(1) 6.8 6 3 F CX16M685-(1) 10 6 9 G CX16M106-(1) 15 6 9 G CX16M156-(1) 22 6 9 G CX16M226-(1) Note: (1) Add suffix to indicate capacitance tolerance K = ± 10 % or M = ± 20 % Document Number: 43018 Revision: 05-Dec-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 69 HA Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar FEATURES • Subminiature package size and light weight • Cylindrical case with axial or radial leads • 2 to 50 VDC • 0.001 µF to 68 µF • Operating temperature range: - 55 °C to + 125 °C • High stability and reliability • Tested in accordance with MIL-PRF-49137 • Unique and comprehensive custom design capability ELECTRICAL CHARACTERISTICS Operating temperature range: - 55 °C to + 125 °C Capacitance: Measured at 120 Hz and 25 °C with a maximum of 2.2 VDC bias and 1.0 Vrms signal. Capacitance Tolerance: Standard tolerance is ± 20 % for ratings 0.1 µF and above, and + 40, - 20 % for ratings below 0.1 µF. Special tolerances are also available. Dissipation Factor: When measured simultaneously with capacitance, DF shall not exceed the value shown in the ratings tables. DC Leakage Current (DCL Max): When measured with DC voltage applied through a 1000 Ω resistor for 5 min, DC leakage (µA) shall not exceed: At 25 °C: Leakage current shall not exceed the values listed in the Standard Ratings Tables At 85 °C: Leakage current shall not exceed 10 times the values listed in the Standard Ratings Tables At 125 °C and 66 % of rated voltage: Leakage current shall not exceed 15 times the values listed in the Standard Ratings Tables. Operating Voltage: Full working voltage up to 85 °C. From 85 °C to 125 °C working voltage derates linearly to 66 % of the 85 °C working voltage. APPLICATIONS • Hearing aids • Portable communications • Space/avionics • Laptop computers MECHANICAL SPECIFICATIONS Solder coated nickel leads (type N32 per MIL-STD-1276) are standard on all case sizes. Leads are weldable and/or solderable. Special leads are available on request (e.g. bare nickle, gold plated nickle or ribbon leads). Lead length is 1 1/2" [38.1 mm] minimum on nonpolar parts. On polar parts the negative lead is 1 1/4" [31.8 mm] minimum and the positive lead is 1 1/2" [38.1 mm] minimum. ORDERING INFORMATION HA MODEL 1.0 CAPACITANCE IN µF 35 DC VOLTAGE RATING AT + 85 °C C7 CASE CODE A* LEAD CONFIGURATION C = Polar N = Non-polar A = Axial R = Radial M CAPACITANCE TOLERANCE E = + 40, - 20 % M = ± 20 % K = ± 10 % J=±5% Example of Part Number Code: HA1.0-35C7AM * To complete part number in rating tables, add A or R. Change suffix if special capacitance tolerance is required. www.vishay.com 70 For technical questions, contact: tantalum@vishay.com Document Number: 43003 Revision: 05-Dec-07 HA Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague DIMENSIONS in inches [millimeters] POLAR STYLE AXIAL RADIAL 3RD DOT AND POLARITY D d D (+) 2ND DOT 2 ND DOT L L 1ST DOT 1 ST DOT TOLERANCE DOT (-) TOLERANCE DOT (-) d (+) E CASE CODE MAX. L MAX. D MAX. E E TOL. ± C0 0.100 [2.54] 0.057 [1.45] 0.030 [0.76] 0.015 [0.38] 0.007[0.18] C1 0.110 [2.80] 0.067 [1.70] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C2 0.125 [3.18] 0.067 [1.70] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C3 0.145 [3.68] 0.067 [1.70] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C4 0.160 [4.06] 0.070 [1.78] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C5 0.160 [4.06] 0.077 [1.96] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C6 0.190 [4.83] 0.077 [1.96] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C7 0.200 [5.08] 0.080 [2.03] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C8 0.225 [5.72] 0.100 [2.54] 0.070 [1.78] 0.020 [0.51] 0.010 [0.25] C9 0.250 [6.35] 0.150 [3.81] 0.120 [3.05] 0.025 [0.64] 0.016 [0.41] d NON POLAR STYLE AXIAL RADIAL T T W W d TOLERANCE DOT TOLERANCE DOT 2ND DOT 2ND DOT LR LA 1ST DOT 1ST DOT 3RD DOT (-) 3RD DOT (+) d E CASE CODE MAX. LA MAX. LR MAX. W MAX. T E E TOL. ± d N1 0.175 [4.45] 0.135 [3.43] 0.120 [3.05] 0.070 [1.78] 0.100 [2.54] 0.020 [0.51] 0.010 [0.25] N2 0.210 [5.33] 0.160 [4.06] 0.120 [3.05] 0.070 [1.78] 0.100 [2.54] 0.020 [0.51] 0.010 [0.25] N3 0.240 [6.10] 0.200 [5.08] 0.140 [3.56] 0.080 [2.03] 0.100 [2.54] 0.020 [0.51] 0.010 [0.25] N4 0.275 [6.99] 0.235 [5.97] 0.190 [4.83] 0.105 [2.67] 0.125 [3.18] 0.020 [0.51] 0.010 [0.25] N5 0.310 [7.87] 0.270 [6.86] 0.290 [7.37] 0.155 [3.94] 0.200 [5.08] 0.025 [0.64] 0.016 [0.41] Document Number: 43003 Revision: 05-Dec-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 71 HA Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar STANDARD RATINGS - POLAR CAPACITORS CAPACITANCE (µF) MAX DF (%) 0.47 1.5 2.2 3.3 4.7 6.8 10 15 22 68 10 10 10 10 10 10 10 10 10 10 1.0 1.5 2.2 3.3 4.7 6.8 10 15 47 10 10 10 10 10 10 10 10 10 0.33 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 33 10 8 8 8 8 8 8 8 8 8 0.22 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 22 10 6 6 6 6 6 6 6 6 6 MAX. DCL AT + 25 °C (µA) 2 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.0 1.5 3 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.0 1.5 4 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.0 1.5 6 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.0 1.5 CASE CODE PART NUMBER C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 HA.47-2C0 (1)M HA1.5-2C1 (1)M HA2.2-2C2 (1)M HA3.3-2C3 (1)M HA4.7-2C4 (1)M HA6.8-2C5 (1)M HA10-2C6 (1)M HA15-2C7 (1)M HA22-2C8 (1)M HA68-2C9 (1)M C1 C2 C3 C4 C5 C6 C7 C8 C9 HA1.0-3C1 (1)M HA1.5-3C2 (1)M HA2.2-3C3 (1)M HA3.3-3C4 (1)M HA4.7-3C5 (1)M HA6.8-3C6 (1)M HA10-3C7 (1)M HA15-3C8 (1)M HA47-3C9 (1)M C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 HA.33-4C0 (1)M HA.68-4C1 (1)M HA1.0-4C2 (1)M HA1.5-4C3 (1)M HA2.2-4C4 (1)M HA3.3-4C5 (1)M HA4.7-4C6 (1)M HA6.8-4C7 (1)M HA10-4C8 (1)M HA33-4C9 (1)M C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 HA.22-6C0 (1)M HA.47-6C1 (1)M TC.68-6C2 (1)M HA1.0-6C3 (1)M HA1.5-6C4 (1)M HA2.2-6C5 (1)M HA3.3-6C6 (1)M HA4.7-6C7 (1)M HA6.8-6C8 (1)M HA22-6C9 (1)M Note: (1) Add for axial, R for radial www.vishay.com 72 For technical questions, contact: tantalum@vishay.com Document Number: 43003 Revision: 05-Dec-07 HA Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague STANDARD RATINGS - POLAR CAPACITORS CAPACITANCE (µF) MAX DF (%) 0.0010 0.0010 0.0015 0.0015 0.0022 0.0022 0.0033 0.0033 0.0047 0.0047 0.15 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 15 10 10 10 10 10 10 10 10 10 10 10 6 6 6 6 6 6 6 6 6 0.10 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 10 10 6 6 6 6 6 6 6 6 6 0.0068 0.0068 0.010 0.015 0.022 0.033 0.047 0.068 0.15 0.22 10 10 10 10 10 10 10 10 6 6 MAX. DCL AT + 25 °C (µA) 10 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.0 1.5 15 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.0 1.5 20 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 CASE CODE PART NUMBER C0 C1 C0 C1 C0 C1 C0 C1 C0 C1 C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 HA.0010-10C0 (1)E HA.0010-10C1 (1)E HA.0015-10C0 (1)E HA.0015-10C1 (1)E HA.0022-10C0 (1)E HA.0022-10C1 (1)E HA.0033-10C0 (1)E HA.0033-10C1 (1)E HA.0047-10C0 (1)E HA.0047-10C1 (1)E HA.15-10C0 (1)M HA.33-10C1 (1)M HA.47-10C2 (1)M HA.68-10C3 (1)M HA1.0-10C4 (1)M HA1.5-10C5 (1)M HA2.2-10C6 (1)M HA3.3-10C7 (1)M HA4.7-10C8 (1)M HA15-10C9 (1)M C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 HA.10-15C0 (1)M HA.22-15C1 (1)M HA.33-15C2 (1)M HA.47-15C3 (1)M HA.68-15C4 (1)M HA1.0-15C5 (1)M HA1.5-15C6 (1)M HA2.2-15C7 (1)M HA3.3-15C8 (1)M HA10-15C9 (1)M C0 C1 C0 C0 C0 C0 C0 C0 C1 C2 HA.0068-0C0 (1)E HA.0068-0C1 (1)E HA.010-20C0 (1)E HA.015-20C0 (1)E HA.022-20C0 (1)E HA.033-20C0 (1)E HA.047-20C0 (1)E HA.068-20C0 (1)E HA.15-20C1 (1)M HA.22-20C2 (1)M Note: (1) Add for axial, R for radial Document Number: 43003 Revision: 05-Dec-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 73 HA Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar STANDARD RATINGS - POLAR CAPACITORS CAPACITANCE (µF) MAX DF (%) MAX. DCL AT + 25 °C (µA) CASE CODE PART NUMBER 20 WVDC AT + 85 °C (Contd) 0.33 6 0.5 C3 HA.33-20C3(1)M 0.47 6 0.5 C4 HA.47-20C4(1)M 0.68 6 0.5 C5 HA.68-20C5(1)M 1.0 6 0.5 C6 HA1.0-20C6(1)M 1.5 6 0.5 C7 HA1.5-20C7(1)M 2.2 6 1.0 C8 HA2.2-20C8(1)M 4.7 6 1.5 C9 HA4.7-20C9(1)M 6.8 6 1.5 C9 HA6.8-20C9(1)M 35 WVDC AT + 85 °C 0.010 6 0.5 C1 HA.010-35C1 (1)E 0.015 6 0.5 C1 HA.015-35C1 (1)E 0.022 6 0.5 C1 HA.022-35C1 (1)E 0.033 6 0.5 C1 HA.033-35C1 (1)E 0.047 6 0.5 C1 HA.047-35C1 (1)E 0.068 6 0.5 C1 HA.068-35C1 (1)E 0.10 6 0.5 C1 HA.10-35C1 (1)M 0.15 6 0.5 C2 HA.15-35C2 (1)M 0.22 6 0.5 C3 HA.22-35C3 (1)M 0.33 6 0.5 C4 HA.33-35C4 (1)M 0.47 6 0.5 C5 HA.47-35C5 (1)M 0.68 6 0.5 C6 HA.68-35C6 (1)M 1.0 6 0.5 C7 HA1.0-35C7 (1)M 1.5 6 0.5 C8 HA1.5-35C8 (1)M 3.3 6 1.5 C9 HA3.3-35C9 (1)M 50 WVDC AT + 85 °C 0.10 6 0.5 C2 HA.10-50C2 (1)M 0.15 6 0.5 C3 HA.15-50C3 (1)M 0.22 6 0.5 C4 HA.22-50C4 (1)M 0.33 6 0.5 C5 HA.33-50C5 (1)M 0.47 6 0.5 C6 HA.47-50C6 (1)M 0.68 6 0.5 C7 HA.68-50C7 (1)M 1.0 6 1.0 C8 HA1.0-50C8 (1)M 1.5 6 1.5 C9 HA1.5-50C9 (1)M 2.2 6 1.5 C9 HA2.2-50C9 (1)M Note: (1) Add A for axial, R for radial www.vishay.com 74 For technical questions, contact: tantalum@vishay.com Document Number: 43003 Revision: 05-Dec-07 HA Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague STANDARD RATINGS - NON-POLAR CAPACITORS CAPACITANCE (µF) MAX DF (%) MAX. DCL AT + 25 °C (µA) CASE CODE PART NUMBER 2 WVDC AT + 85 °C 1.0 10 0.5 N1 HA1.0-2N1 (1)M 2.2 10 0.5 N2 HA2.2-2N2 (1)M 4.7 10 0.5 N3 HA4.7-2N3 (1)M 10 10 1.0 N4 HA10-2N4 (1)M 33 10 1.5 N5 HA33-2N5 (1)M 3 WVDC AT + 85 °C 0.68 10 0.5 N1 HA.68-3N1 (1)M 1.5 10 0.5 N2 HA1.5-3N2 (1)M 3.3 10 0.5 N3 HA3.3-3N3 (1)M 6.8 10 1.0 N4 HA6.8-3N4 (1)M 22 10 1.5 N5 HA22-3N5 (1)M 4 WVDC AT + 85 °C 0.47 8 0.5 N1 HA.47-4N1 (1)M 1.0 8 0.5 N2 HA1.0-4N2 (1)M 2.2 8 0.5 N3 HA2.2-4N3 (1)M 4.7 8 1.0 N4 HA4.7-4N4 (1)M 15 8 1.5 N5 HA15-4N5 (1)M N1 HA.33-6N1 (1)M 6 WVDC AT + 85 °C 0.33 6 0.5 0.68 6 0.5 N2 HA.68-6N2 (1)M 1.5 6 0.5 N3 HA1.5-6N3 (1)M 3.3 6 1.0 N4 HA3.3-6N4 (1)M 10 6 1.5 N5 HA10-6N5 (1)M N1 HA.22-10N1 (1)M 10 WVDC AT + 85 °C 0.22 6 0.5 0.47 6 0.5 N2 HA.47-10N2 (1)M 1.0 6 0.5 N3 HA1.0-10N3 (1)M 2.2 6 1.0 N4 HA2.2-10N4 (1)M 6.8 6 1.5 N5 HA6.8-10N5 (1)M 15 WVDC AT + 85 °C 0.15 6 0.5 N1 HA.15-15N1 (1)M 0.33 6 0.5 N2 HA.33-15N2 (1)M 0.68 6 0.5 N3 HA.68-15N3 (1)M 1.5 6 1.0 N4 HA1.5-15N4 (1)M 4.7 6 1.5 N5 HA4.7-15N5 (1)M 20 WVDC AT + 85 °C 0.010 6 0.5 N1 HA.010-20N1 (1)M 0.015 6 0.5 N1 HA.015-20N1 (1)M 0.022 6 0.5 N1 HA.022-20N1 (1)M Note: (1) Add for axial, R for radial Document Number: 43003 Revision: 05-Dec-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 75 HA Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague STANDARD RATINGS - NON-POLAR CAPACITORS CAPACITANCE (µF) MAX DF (%) 0.033 0.047 0.068 0.10 0.22 0.47 1.0 2.2 3.3 6 6 6 6 6 6 6 6 6 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 6 6 6 6 6 6 6 6 0.068 0.15 0.33 0.68 6 6 6 6 MAX. DCL AT + 25 °C (µA) 20 WVDC AT + 85 °C (Contd.) 0.5 0.5 0.5 0.5 0.5 0.5 1.0 1.5 1.5 35 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 1.0 1.0 1.5 1.5 50 WVDC AT + 85 °C 0.5 0.5 1.0 1.5 CASE CODE PART NUMBER N2 N2 N2 N1 N2 N3 N4 N5 N5 HA.033-20N2 (1)M HA.047-20N2 (1)M HA.068-20N2 (1)M HA.10-20N1 (1)M HA.22-20N2 (1)M HA.47-20N3 (1)M HA1.0-20N4 (1)M H2.2-20N5 (1)M HA3.3-20N5 (1)M N2 N2 N3 N3 N4 N4 N5 N5 HA.10-35N2 (1)M HA.15-35N2 (1)M HA.22-35N3 (1)M HA.33-35N3 (1)M HA.47-35N4 (1)M HA.68-35N4 (1)M HA1.0-35N5 (1)M HA1.5-35N5 (1)M N3 N3 N4 N5 HA.068-50N3 (1)M HA.15-50N3 (1)M HA.33-50N4 (1)M HA.68-50N5 (1)M Note: (1) Add for axial, R for radial MARKING All other case sizes have color dot marking: HA Capacitors case sizes N4 and N5 are print marked: - Capacitance is in picofarads - 1st and 2nd digits are significant figures - 3rd digit indicates the number of zeros. Capacitance Tolerance Is indicated by a dot on the side of the case. Black dot is omitted. Color Color Digit In picofarads, indicated by 3 dots. Black 0 1st and 2nd dot give the significant digits. 3rd dot indicates the number of zeros. Color dot location is shown on the dimensional sketches. Black dot is omitted on black sleeve. Brown 1 Red 2 Orange 3 Tolerance Yellow 4 Green 5 Blue 6 Gold ±5% Violet 7 Silver ± 10 % Grey 8 None ± 20 % White 9 None + 40 %/- 20 % The positive lead is indicated by a color dot of red epoxy on the unit. www.vishay.com 76 Capacitance e.g. Yellow-Violet-Green = 4 700 000 pf For technical questions, contact: tantalum@vishay.com = 4.7 µF Document Number: 43003 Revision: 05-Dec-07 HA Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague PERFORMANCE AND RELIABILITY The capacitors are tested in accordance with MIL-PRF-49137, with specific requirements as follows: IMPEDANCE VS. FREQUENCY Temperature Stability: When tested per MIL-PRF-49137/6, capacitance shall be within ±15 % at - 55 °C and 85 °C, and ±10 % at 25 °C after exposure to temperature extremes. DF shall be within 200 % of initial limit at - 55 °C, 150 % of initial limit at 85 °C, and meet the initial at 25 °C. DCL shall be within 10 x initial limit at 85 °C, and meet the initial limit at 25 °C. Life: (per Method 108 of MIL-STD-202) after 1000 h at 85 °C and rated voltage; capacitance shall be within ± 10 % of initial limit, DF within initial limits, and leakage within 200 % of initial limit. 5K 1K 50 20 10 5.0 0.2 SP 0V 0 0 10 µF -1 - 10 - 40 EC I IF TYP 0V 1 F- 0µ 10 L ICA 1 -5 SP EC ON C FI I AT µH 0 -2 V ON µF -2 0V 0.5 0.1 100 500 1 Hz 2 kHz 5 10 20 50 100 FREQUENCY 500 1 2 kHz 5 10 MHz LEAKAGE CURRENT - TEMPERATURE 1.0 (MFD-WVDC) D.C. LEAKAGE CURRENT (µA) CHANGE IN CAPACITANCE % +5 I AT IC 4.7 1.0 Solderability: (per Method 208 of MIL-STD-202) After dipping leads in 235 °C molten solder to within 0.125" of the body of the unit, the solder shall cover 95 % of the lead surface. (MFD-WVDC) 7 µF -2 0V 0. 0 0. 4 04 7 µ 7 F µF -2 -3 0 V 5V 0.0 0.0 47 47 µF µF -50 -3 V 5V 4.7 4.7 µF µF -10 -2 V 0V 100 Resistance to Soldering Heat: (per Method 210 0f MIL-STD-202, Condition B) After immersion in 260 °C molten solder to within a 1/4" of the body of the unit, there shall be no evidence of mechanical or electrical degradation. + 10 04 200 2.0 CAPACITANCE VS. TEMPERATURE 0. 500 Surge Voltage: (per MIL-PRF-49317) After 1000 cycles at 85 °C and 1.3 x WVDC; capacitance shall be within ± 10 % of initial limit, DF and leakage within initial limits. Terminal Strength: (per Method 211 of MIL-STD-202) After the following test there shall be no loosening of the terminals or permanent damage to the terminals. Test Condition A: (Pull Test) 0.010" leads withstand 1 pound, 0.016" leads 2 pounds and 0.007" leads 1/2 pound. Test Condition C: (Bend Test) All leads shall withstand 3 - 90° bends with a 1/2 pound applied force. (MFD-WVDC) 2K IMPEDANCE Ω Moisture Resistance: (per Method 106 of MIL-STD-202) After 10 cycles of 24 h at 25 °C to 65 °C and 80-98 % RH; capacitance shall be within ± 15 % of initial value, DF within 1.5 x initial limit and leakage within 3 x initial limit. 10K 1 µF-20 V 100 µF-10 V 0.1 0.01 - 10 + 25 + 85 + 100 - 40 - 10 TEMPERATURE °C Document Number: 43003 Revision: 05-Dec-07 For technical questions, contact: tantalum@vishay.com 0 + 20 + 85 TEMPERATURE °C www.vishay.com 77 SHA Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar FEATURES • Subminiature package size and light weight • Cylindrical case with axial or radial leads • 2 to 35 VDC • 0.22 µF to 68 µF • Operating temperature range: - 55 °C to + 125 °C • High stability and reliability • Tested in accordance with MIL-PRF-49137 • Utilize high CV technology to extend the range of capacitance values in each size • Unique and comprehensive custom design capability ELECTRICAL CHARACTERISTICS Operating Temperature Range: - 55 °C to + 125 °C APPLICATIONS Capacitance: Measured at 120 Hz and 25 °C with a maximum of 2.2 VDC bias and 1.0 Vrms signal. • Hearing aids Capacitance Tolerance: Standard tolerance is ± 20 % for ratings 0.1 µF and above, and + 40, - 20 % for ratings below 0.1 µF. Special tolerances are also available. • Space/avionics Dissipation Factor: When measured simultaneously with capacitance, DF shall not exceed the value shown in the ratings tables. DC Leakage Current (DCL Max): When measured with DC voltage applied through a 1000 W resistor for 5 min, DC leakage (µA) shall not exceed: At 25 °C: Leakage current shall not exceed the values listed in the Standard Ratings Tables At 85 °C: Leakage current shall not exceed 10 times the values listed in the Standard Ratings Tables At 125 °C and 66 % of Rated Voltage: Leakage current shall not exceed 15 times the values listed in the Standard Ratings Tables. • Portable communications • Laptop computers MECHANICAL SPECIFICATIONS Solder coated nickel leads (type N32 per MIL-STD-1276) are standard on all case sizes. Leads are weldable and/or solderable. Special leads are available on request (e.g. bare nickel, gold plated nickle or ribbon leads). Lead length is 1 1/2" [38.1 mm] minimum on non-polar parts. On polar parts the negative lead is 1 1/4" [31.8 mm] minimum and the positive lead is 1 1/2" [38.1 mm] minimum. Operating Voltage: Full working voltage up to 85 °C. From 85 °C to 125 °C working voltage derates linearly to 66 % of the 85 °C working voltage. ORDERING INFORMATION SHA MODEL 1.0 CAPACITANCE (µF) 35 DC VOLTAGE RATING at + 85 °C C7 CASE CODE A (1) LEAD CONFIGURATION C = Polar N = Non-polar A = Axial R = Radial M CAPACITANCE TOLERANCE E = + 40, - 20 % M = ± 20 % K = ± 10 % J=±5% EXAMPLE OF PART NUMBER CODE: SHA1.0-35C7AM Note: (1) To complete part number in rating tables, add A or R. Change suffix if special capacitance tolerance is required. www.vishay.com 78 For technical questions, contact: tantalum@vishay.com Document Number: 43004 Revision: 06-Dec-07 SHA Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague DIMENSIONS in inches [millimeters] POLAR STYLE AXIAL RADIAL 3RD DOT AND POLARITY D d D (+) 2ND DOT 2 ND DOT L L 1ST DOT 1 ST DOT TOLERANCE DOT (-) TOLERANCE DOT (-) d (+) E CASE CODE MAX. L MAX. D MAX. E E TOL. ± C0 0.100 [2.54] 0.057 [1.45] 0.030 [0.76] 0.015 [0.38] 0.007[0.18] C1 0.110 [2.80] 0.067 [1.70] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C2 0.125 [3.18] 0.067 [1.70] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C3 0.145 [3.68] 0.067 [1.70] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C4 0.160 [4.06] 0.070 [1.78] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C5 0.160 [4.06] 0.077 [1.96] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C6 0.190 [4.83] 0.077 [1.96] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C7 0.200 [5.08] 0.080 [2.03] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C8 0.225 [5.72] 0.100 [2.54] 0.070 [1.78] 0.020 [0.51] 0.010 [0.25] C9 0.250 [6.35] 0.150 [3.81] 0.120 [3.05] 0.025 [0.64] 0.016 [0.41] d NON POLAR STYLE AXIAL RADIAL T T W W d TOLERANCE DOT TOLERANCE DOT 2ND DOT 2ND DOT LR LA 1ST DOT 1ST DOT 3RD DOT (-) 3RD DOT (+) d E CASE CODE MAX. LA MAX. LR MAX. W MAX. T E E TOL. ± d N1 0.175 [4.45] 0.135 [3.43] 0.120 [3.05] 0.070 [1.78] 0.100 [2.54] 0.020 [0.51] 0.010 [0.25] N2 0.210 [5.33] 0.160 [4.06] 0.120 [3.05] 0.070 [1.78] 0.100 [2.54] 0.020 [0.51] 0.010 [0.25] N3 0.240 [6.10] 0.200 [5.08] 0.140 [3.56] 0.080 [2.03] 0.100 [2.54] 0.020 [0.51] 0.010 [0.25] N4 0.275 [6.99] 0.235 [5.97] 0.190 [4.83] 0.105 [2.67] 0.125 [3.18] 0.020 [0.51] 0.010 [0.25] N5 0.310 [7.87] 0.270 [6.86] 0.290 [7.37] 0.155 [3.94] 0.200 [5.08] 0.025 [0.64] 0.016 [0.41] Document Number: 43004 Revision: 06-Dec-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 79 SHA Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar STANDARD RATINGS - POLAR CAPACITORS CAPACITANCE (µF) MAX DF (%) 3.3 10 15 10 22 10 68 10 2.2 10 3.3 4.7 MAX. DCL AT + 25 °C (µA) CASE CODE PART NUMBER 0.5 C1 SHA3.3-2C1 (1)M 0.5 C5 SHA15-2C5 (1)M 1.0 C6 SHA22-2C6 (1)M 1.5 C8 SHA68-2C8 (1)M 0.5 C1 SHA2.2-3C1 (1)M 10 0.5 C2 SHA3.3-3C2 (1)M 10 0.5 C3 SHA4.7-3C3 (1)M 6.8 10 0.5 C4 SHA6.8-3C4 (1)M 10 10 0.5 C5 SHA10-3C5 (1)M 15 10 1.0 C6 SHA15-3C6 (1)M 22 10 1.0 C7 SHA22-3C7 (1)M 47 10 1.5 C8 SHA47-3C8 (1)M 68 10 5.0 C9 SHA68-3C9 (1)M 1.5 8 0.5 C1 SHA1.5-4C1 (1)M 2.2 8 0.5 C2 SHA2.2-4C2 (1)M 3.3 8 0.5 C3 SHA3.3-4C3 (1)M 4.7 8 0.5 C4 SHA4.7-4C4 (1)M 6.8 8 0.5 C5 SHA6.8-4C5 (1)M 10 8 1.0 C6 SHA10-4C6 (1)M 15 8 1.0 C7 SHA15-4C7 (1)M 33 8 1.5 C8 SHA33-4C8 (1)M 47 8 5.0 C9 SHA47-4C9 (1)M 2 WVDC AT + 85 °C 3 WVDC AT + 85 °C 4 WVDC AT + 85 °C 6 WVDC AT + 85 °C 1.0 6 0.5 C1 SHA1.0-6C1 (1)M 1.5 6 0.5 C2 SHA1.5-6C2 (1)M 2.2 6 0.5 C3 SHA2.2-6C3 (1)M 3.3 6 0.5 C4 SHA3.3-6C4 (1)M 4.7 6 0.5 C5 SHA4.7-6C5 (1)M 6.8 6 1.0 C6 SHA6.8-6C6 (1)M 10 6 1.0 C7 SHA10-6C7 (1)M 22 6 1.5 C8 SHA22-6C8 (1)M 33 6 5.0 C9 SHA33-6C9 (1)M 10 WVDC AT + 85 °C 0.68 6 0.5 C1 SHA.68-10C1 (1)M 1.0 6 0.5 C2 SHA1.0-10C2 (1)M 1.5 6 0.5 C3 SHA1.5-10C3 (1)M 2.2 6 0.5 C4 SHA2.2-10C4 (1)M 3.3 6 0.5 C5 SHA3.3-10C5 (1)M 4.7 6 1.0 C6 SHA4.7-10C6 (1)M 6.8 6 1.0 C7 SHA6.8-10C7 (1)M 15 6 1.5 C8 SHA15-10C8 (1)M 22 8 5.0 C9 SHA22-10C9 (1)M Note: (1) Add A for axial, R for radial www.vishay.com 80 For technical questions, contact: tantalum@vishay.com Document Number: 43004 Revision: 06-Dec-07 SHA Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague STANDARD RATINGS - POLAR CAPACITORS CAPACITANCE (µF) MAX DF (%) 0.47 0.68 1.0 1.5 2.2 3.3 4.7 15 6 6 6 6 6 6 6 8 0.33 0.47 0.68 1.0 1.5 2.2 3.3 10 6 6 6 6 6 6 6 8 2.2 3.3 6.8 6 6 8 0.22 0.33 0.47 0.68 1.0 1.5 1.5 2.2 6 6 6 6 6 6 6 6 MAX. DCL AT + 25 °C (µA) 15 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 1.0 1.0 5.0 20 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 1.0 1.0 5.0 25 WVDC AT + 85 °C 1.0 1.5 5.0 35 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 0.5 1.0 1.5 CASE CODE PART NUMBER C1 C1 C3 C4 C5 C6 C7 C9 SHA.47-15C1 (1)M SHA.68-15C1 (1)M SHA1.0-15C3 (1)M SHA1.5-15C4 (1)M SHA2.2-15C5 (1)M SHA3.3-15C6 (1)M SHA4.7-15C7 (1)M SHA15-15C9 (1)M C1 C2 C3 C4 C5 C6 C7 C9 SHA.33-20C1 (1)M SHA.47-20C2 (1)M SHA.68-20C3 (1)M SHA1.0-20C4 (1)M SHA1.5-20C5 (1)M SHA2.2-20C6 (1)M SHA3.3-20C7 (1)M SHA10-20C9 (1)M C7 C8 C9 SHA2.2-25C7 (1)M SHA3.3-25C8 (1)M SHA6.8-25C9 (1)M C1 C2 C3 C4 C5 C6 C7 C8 SHA.22-35C1 (1)M SHA.33-35C2 (1)M SHA.47-35C3 (1)M SHA.68-35C4 (1)M SHA1.0-35C5 (1)M SHA1.5-35C6 (1)M SHA1.5-35C7 (1)M SHA2.2-35C8 (1)M CASE CODE PART NUMBER Note: (1) Add A for axial, R for radial STANDARD RATINGS - NON-POLAR CAPACITORS CAPACITANCE (µF) MAX DF (%) MAX. DCL AT + 25 °C (µA) 3.3 10 0.5 N2 SHA3.3-2N2 (1)M 6.8 10 0.5 N3 SHA6.8-2N3 (1)M 15 10 1.0 N4 SHA15-2N4 (1)M 47 10 2.5 N5 SHA47-2N5 (1)M 2 WVDC AT + 85 °C 4 WVDC AT + 85 °C 2.2 8 0.5 N2 SHA2.2-4N2 (1)M 4.7 8 0.5 N3 SHA4.7-4N3 (1)M 10 8 1.0 N4 SHA10-4N4 (1)M 33 8 2.5 N5 SHA33-4N5 (1)M Note (1) Add A for axial, R for radial Document Number: 43004 Revision: 06-Dec-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 81 SHA Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague STANDARD RATINGS - NON-POLAR CAPACITORS CAPACITANCE (µF) MAX DF (%) 1.5 3.3 6.8 22 6 6 6 6 1.0 2.2 4.7 15 6 6 6 6 0.68 1.5 3.3 10 6 6 6 6 0.47 1.0 2.2 6.8 6 6 6 6 0.33 0.68 1.5 6 6 6 MAX. DCL AT + 25 °C (µA) 6 WVDC AT + 85 °C 0.5 1.0 1.0 2.5 10 WVDC AT + 85 °C 0.5 1.0 1.5 2.5 15 WVDC AT + 85 °C 0.5 1.0 1.5 2.5 20 WVDC AT + 85 °C 0.5 1.0 1.5 2.5 35 WVDC AT + 85 °C 0.5 1.0 1.5 CASE CODE PART NUMBER N2 N3 N4 N5 SHA1.5-6N2 (1)M SHA3.3-6N3 (1)M SHA6.8-6N4 (1)M SHA22-6N5 (1)M N2 N3 N4 N5 SHA1.0-10N2 (1)M SHA2.2-10N3 (1)M SHA4.7-10N4 (1)M SHA15-10N5 (1)M N2 N3 N4 N5 SHA.68-15N2 (1)M SHA1.5-15N3 (1)M SHA3.3-15N4 (1)M SHA10-15N5 (1)M N2 N3 N4 N5 SHA.47-20N2 (1)M SHA1.0-20N3 (1)M SHA2.2-20N4 (1)M SHA6.8-20N5 (1)M N2 N3 N4 SHA.33-35N2 (1)M SHA.68-35N3 (1)M SHA1.5-35N4 (1)M Note (1) Add A for axial, R for radial MARKING SHA Capacitors case sizes N4 and N5 are print marked: - Capacitance is in picofarads - 1st and 2nd digits are significant figures - 3rd digit indicates the number of zeros. Capacitance Tolerance Color Is indicated by a dot on the side of the case. Black dot is omitted. Gold Capacitance Color Digit In picofarads, indicated by 3 dots. 1st and 2nd dot give the significant digits. 3rd dot indicates the number of zeros. Color dot location is shown on the dimensional sketches. Black dot is omitted on black sleeve. Black 0 Brown 1 Tolerance ±5% Red 2 Orange 3 Yellow 4 Green 5 Blue 6 Violet 7 Silver ± 10 % Grey 8 None ± 20 % White 9 None + 40 %/- 20 % The positive lead is indicated by a color dot of red epoxy on the unit. Radial lead style is marked with brown epoxy on the top. Axial lead style is marked with brown epoxy on the cathode end www.vishay.com 82 All other case sizes have color dot marking: e.g. Yellow-Violet-Green = 4 700 000 pf For technical questions, contact: tantalum@vishay.com = 4.7 µF Document Number: 43004 Revision: 06-Dec-07 SHA Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague PERFORMANCE AND RELIABILITY The capacitors are tested in accordance with MIL-PRF-49137, with specific requirements as follows: IMPEDANCE VS. FREQUENCY Temperature Stability: When tested per MIL-PRF-49137/6, capacitance shall be within ± 15 % at - 55 °C and 85 °C, and ± 10 % at 25 °C after exposure to temperature extremes. DF shall be within 200 % of initial limit at - 55 °C, 150 % of initial limit at 85 °C, and meet the initial at 25 °C. DCL shall be within 10 x initial limit at 85 °C, and meet the initial limit at 25 °C. Life: (per Method 108 of MIL-STD-202) after 1000 h at 85 °C and rated voltage; capacitance shall be within ± 10 % of initial limit, DF within initial limits, and leakage within 200 % of initial limit. Surge Voltage: (per MIL-PRF-49317) After 1000 cycles at 85 °C and 1.3 x WVDC; capacitance shall be within ± 10 % of initial limit, DF and leakage within initial limits. Resistance to Soldering Heat: (per Method 210 of MIL-STD-202, Condition B) After immersion in 260 °C molten solder to within a 1/4" of the body of the unit, there shall be no evidence of mechanical or electrical degradation. 5K 1K CHANGE IN CAPACITANCE % + 10 (MFD-WVDC) +5 S C PE I C FI I AT ON 0V F 0µ -1 10 0 0 10 µF - V 10 SP - 10 - 40 E L 1 -5 F CI TY A PIC IC I AT 0V µH -2 ON 04 7 µF -2 0V 0. 0. 04 04 7 µ 7 F µF -2 -3 0 V 5V 0.0 0.0 47 47 µF µF -50 -3 V 5V 4.7 4.7 µF µF -10 -2 V 0V 200 100 50 20 10 5.0 2.0 4.7 0V 0.5 0.2 0.1 100 500 1 Hz 2 kHz 5 10 20 50 100 FREQUENCY 500 kHz 1 2 5 10 MHz LEAKAGE CURRENT - TEMPERATURE 1.0 (MFD-WVDC) 1 µF-20 V 100 µF-10 V 0.1 0.01 - 40 - 10 µF -2 1.0 D.C. LEAKAGE CURRENT (µA) CAPACITANCE VS. TEMPERATURE 0. 500 Solderability: (per Method 208 of MIL-STD-202) After dipping leads in 235 °C molten solder to within 0.125" of the body of the unit, the solder shall cover 95 % of the lead surface. Terminal Strength: (per Method 211 of MIL-STD-202) After the following test there shall be no loosening of the terminals or permanent damage to the terminals. Test Condition A: (Pull Test) 0.010" leads withstand 1 pound, 0.016" leads 2 pounds and 0.007" leads 1/2 pound. Test Condition C: (Bend Test) All leads shall withstand 3 - 90° bends with a 1/2 pound applied force. (MFD-WVDC) 2K IMPEDANCE Ω Moisture Resistance: (per Method 106 of MIL-STD-202) After 10 cycles of 24 h at 25 °C to 65 °C and 80-98 % RH; capacitance shall be within ± 15 % of initial value, DF within 1.5 x initial limit and leakage within 3 x initial limit. 10K + 25 + 85 - 10 + 100 0 + 20 + 85 TEMPERATURE °C TEMPERATURE °C Document Number: 43004 Revision: 06-Dec-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 83 TC Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar FEATURES • Subminiature package size and light weight • Rectangular case with axial or radial leads • 2 to 50 VDC • 0.1 µF to 470 µF • Operating temperature range: - 55 °C to + 125 °C • High stability and reliability • Tested in accordance with MIL-PRF-49137 • Unique and comprehensive custom design capability ELECTRICAL CHARACTERISTICS Operating temperature range: - 55 °C to + 125 °C Capacitance: Measured at 120 Hz and 25 °C with a maximum of 2.2 VDC bias and 1.0 Vrms signal. Capacitance Tolerance: Standard tolerance is ± 20 % for ratings 0.1 µF and above, and + 40, - 20 % for ratings below 0.1 µF. Special tolerances are also available. Dissipation Factor: When measured simultaneously with capacitance, DF shall not exceed the value shown in theratings tables. DC Leakage Current (DCL Max): When measured with DC voltage applied through a 1000 Ω resistor for 5 minutes, DC leakage (µA) shall not exceed: At 25 °C: Leakage current shall not exceed the values listed in the Standard Ratings Tables At 85 °C: Leakage current shall not exceed 10 times the values listed in the Standard Ratings Tables At 125 °C and 66 % of Rated Voltage: Leakage current shall not exceed 15 times the values listed in the Standard Ratings Tables. Operating Voltage: Full working voltage up to 85 °C. From 85 °C to 125 °C working voltage derates linearly to 66 % of the 85 °C working voltage. APPLICATIONS • Hearing aids • Portable communications • Space/avionics • Laptop computers MECHANICAL SPECIFICATIONS Solder coated nickel leads (type N32 per MIL-STD-1276) are standard on all case sizes. Leads are weldable and/or solderable. Special leads are available on request (e.g. bare nickel, gold plated nickel or ribbon leads). Lead length is 1 1/2" [38.1 mm] minimum on nonpolar parts. On polar parts the negative lead is 1 1/4" [31.8 mm] minimum and the positive lead is 1 1/2" [38.1 mm] minimum. ORDERING INFORMATION TC MODEL 1.0 CAPACITANCE IN µF 35 DC VOLTAGE RATING AT + 85 °C C3 CASE CODE A (1) LEAD CONFIGURATION C = Polar N = Non-polar A = Axial R = Radial Example of Part Number Code: TC1.0-35C3AM M CAPACITANCE TOLERANCE E = + 40, - 20 % M = ± 20 % K = ± 10 % J=±5% Note: (1) To complete part number in rating tables, add A or R. Change suffix if special capacitance tolerance is required. www.vishay.com 84 For technical questions, contact: tantalum@vishay.com Document Number: 43005 Revision: 12-Sep-07 TC Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague DIMENSIONS in inches [millimeters] POLAR STYLE AXIAL RADIAL T T RED EPOXY POLARITY DOT W W d (+) 3RD DOT 3RD DOT 2ND DOT 2ND DOT L L 1ST DOT 1ST DOT TOLERANCE DOT TOLERANCE DOT d d (+) (-) E THE 3RD DOT IS ON THE END OF THE CX SIZE CASE CODE L MAX. W MAX. T MAX. E E TOL. ± d CX 0.075 [1.91] 0.050 [1.27] 0.040 [1.02] 0.030 [0.76] 0.015 [0.38] 0.007 [0.18] C0 0.100 [2.54] 0.050 [1.27] 0.040 [1.02] 0.030 [0.76] 0.015 [0.38] 0.007 [0.18] C1 0.125 [3.18] 0.070 [1.78] 0.040 [1.02] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C2 0.165 [4.19] 0.120 [3.05] 0.070 [1.78] 0.100 [2.54] 0.020 [0.51] 0.010 [0.25] C3 0.225 [5.72] 0.185 [4.70] 0.075 [1.91] 0.150 [3.81] 0.020 [0.51] 0.010 [0.25] C4 0.290 [7.37] 0.220 [5.59] 0.110 [2.79] 0.180 [4.57] 0.025 [0.64] 0.016 [0.41] C5 0.310 [7.87] 0.230 [5.84] 0.130 [3.30] 0.200 [5.08] 0.025 [0.64] 0.016 [0.41] C6 0.475 [12.07] 0.375 [9.53] 0.150 [3.81] 0.300 [7.62] 0.025 [0.64] 0.016 [0.41] NON POLAR STYLE AXIAL RADIAL T T W d W TOLERANCE DOT TOLERANCE DOT 2ND DOT 2ND DOT LA LR 1ST DOT 1ST DOT 3RD DOT 3RD DOT d E CASE CODE LA MAX. LR MAX. W MAX. T MAX. E MAX. E TOL. ± d N1 0.220 [5.59] 0.180 [4.57] 0.125 [3.18] 0.125 [3.18] 0.100 [2.54] 0.020 [0.51] 0.010 [0.25] N2 0.280 [7.11] 0.240 [6.10] 0.140 [3.56] 0.180 [4.57] 0.100 [2.54] 0.025 [0.64] 0.010 [0.25] N3 0.370 [9.40] 0.315 [8.00] 0.180 [4.57] 0.220 [5.59] 0.150 [3.81] 0.025 [0.64] 0.016 [0.41] N4 0.390 [9.91] 0.335 [8.51] 0.230 [5.84] 0.230 [5.84] 0.180 [4.57] 0.025 [0.64] 0.016 [0.41] Document Number: 43005 Revision: 12-Sep-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 85 TC Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar STANDARD RATINGS - POLAR CAPACITORS CAPACITANCE (µF) MAX. DF (%) 0.47 0.68 1.0 2.2 10 33 100 150 470 10 10 10 10 10 10 15 15 20 1.5 6.8 22 68 100 330 10 10 10 10 10 20 0.33 1.0 4.7 15 47 68 220 10 8 8 8 8 8 15 0.22 0.68 3.3 10 33 47 150 10 6 6 6 6 6 10 0.0010 0.0010 0.0015 0.0015 0.0022 0.0022 0.0033 0.0033 0.0047 0.0047 0.15 0.47 2.2 6.8 22 33 100 10 10 10 10 10 10 10 10 10 10 10 6 6 6 6 6 8 MAX. DCL AT + 25 °C (µA) 2 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 1.0 2.0 3.0 9.0 3 WVDC AT + 85 °C 0.5 0.5 1.0 2.0 3.0 9.0 4 WVDC AT + 85 °C 0.5 0.5 0.5 1.0 2.0 3.0 9.0 6 WVDC AT + 85 °C 0.5 0.5 0.5 1.0 2.0 3.0 9.0 10 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.0 2.0 3.0 9.0 CASE CODE PART NUMBER C0 C0 C0 C1 C2 C3 C4 C5 C6 TC.47-2C0 (1)M TC.68-2C0 (1)M TC1.0-2C0 (1)M TC2.2-2C1 (1)M TC10-2C2 (1)M TC33-2C3 (1)M TC100-2C4 (1)M TC150-2C5 (1)M TC470-2C6 (1)M C1 C2 C3 C4 C5 C6 TC1.5-3C1 (1)M TC6.8-3C2 (1)M TC22-3C3 (1)M TC68-3C4 (1)M TC100-3C5 (1)M TC330-3C6 (1)M C0 C1 C2 C3 C4 C5 C6 TC.33-4C0 (1)M TC1.0-4C1 (1)M TC4.7-4C2 (1)M TC15-4C3 (1)M TC47-4C4 (1)M TC68-4C5 (1)M TC220-4C6 (1)M C0 C1 C2 C3 C4 C5 C6 TC.22-6C0 (1)M TC.68-6C1 (1)M TC3.3-6C2 (1)M TC10-6C3 (1)M TC33-6C4 (1)M TC47-6C5 (1)M TC150-6C6 (1)M C0 C1 C0 C1 C0 C1 C0 C1 C0 C1 C0 C1 C2 C3 C4 C5 C6 TC.0010-10C0 (1)E TC.0010-10C1 (1)E TC.0015-10C0 (1)E TC.0015-10C1 (1)E TC.0022-10C0 (1)E TC.0022-10C1 (1)E TC.0033-10C0 (1)E TC.0033-10C1 (1)E TC.0047-10C0 (1)E TC.0047-10C1 (1)E TC.15-10C0 (1)M TC.47-10C1 (1)M TC2.2-10C2 (1)M TC6.8-10C3 (1)M TC22-10C4 (1)M TC33-10C5 (1)M TC100-10C6 (1)M Note: (1) Add A for axial, R for radial www.vishay.com 86 For technical questions, contact: tantalum@vishay.com Document Number: 43005 Revision: 12-Sep-07 TC Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague STANDARD RATINGS - POLAR CAPACITORS CAPACITANCE (µF) MAX. DF (%) 0.10 0.33 1.5 15 22 68 10 6 6 6 6 8 0.033 0.033 0.047 0.047 0.068 0.068 0.10 0.15 0.22 1.0 3.3 4.7 10 15 47 10 6 10 6 10 6 6 6 6 6 6 6 6 6 8 0.68 2.2 6.8 10 33 6 6 6 6 6 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 6 6 6 6 6 6 6 6 6 6 6 6 6 0.15 4.7 6.8 6 6 6 MAX. DCL AT + 25 °C (µA) 15 WVDC AT + 85 °C 0.5 0.5 0.5 2.0 3.0 9.0 20 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.0 1.0 2.0 3.0 9.0 25 WVDC AT + 85 °C 0.5 1.0 2.0 3.0 9.0 35 WVDC AT + 85 °C 0.5 0.5 0.5 1.0 1.0 1.0 2.0 2.0 2.0 3.0 9.0 9.0 9.0 50 WVDC AT + 85 °C 0.5 3.0 9.0 CASE CODE PART NUMBER C0 C1 C2 C4 C5 C6 TC.10-15C0 (1)M TC.33-15C1 (1)M TC1.5-15C2 (1)M TC15-15C4 (1)M TC22-15C5 (1)M TC68-15C6 (1)M C0 C1 C0 C1 C0 C1 C1 C1 C1 C2 C3 C3 C4 C5 C6 TC.033-20C0 (1)E TC.033-20C1 (1)E TC.047-20C0 (1)E TC.047-20C1 (1)E TC.068-20C0 (1)E TC.068-20C1 (1)E TC.10-20C1 (1)M TC.15-20C1 (1)M TC.22-20C1 (1)M TC1.0-20C2 (1)M TC3.3-20C3 (1)M TC4.7-20C3 (1)M TC10-20C4 (1)M TC15-20C5 (1)M TC47-20C6 (1)M C2 C3 C4 C5 C6 TC.68-25C2 (1)M TC2.2-25C3 (1)M TC6.8-25C4 (1)M TC10-25C5 (1)M TC33-25C6 (1)M C2 C2 C2 C3 C3 C3 C4 C4 C4 C5 C6 C6 C6 TC.22-35C2 (1)M TC.33-35C2 (1)M TC.47-35C2 (1)M TC.68-35C3 (1)M TC1.0-35C3 (1)M TC1.5-35C3 (1)M TC2.2-35C4 (1)M TC3.3-35C4 (1)M TC4.7-35C4 (1)M TC6.8-35C5 (1)M TC10-35C6 (1)M TC15-35C6 (1)M TC22.35C6 (1)M C2 C5 C6 TC.15-50C2 (1)M TC4.7-50C5 (1)M TC6.8-50C6 (1)M Note: (1) Add A for axial, R for radial Document Number: 43005 Revision: 12-Sep-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 87 TC Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar STANDARD RATINGS - NON-POLAR CAPACITORS CAPACITANCE (µF) MAX. DF (%) 4.7 15 47 68 10 10 15 15 3.3 10 33 47 10 10 10 10 2.2 6.8 22 33 8 8 8 8 1.5 4.7 15 22 6 6 6 6 1.0 3.3 10 15 6 6 6 6 0.68 6.8 10 6 6 6 0.47 1.5 2.2 4.7 6.8 6 6 6 6 6 0.33 1.0 3.3 4.7 6 6 6 6 0.10 0.15 0.22 0.33 0.47 0.68 1.0 6 6 6 6 6 6 6 2.2 Note: (1) Add A for axial, R for radial 6 www.vishay.com 88 MAX. DCL AT + 25 °C (µA) 2 WVDC AT + 85 °C 0.5 1.0 2.0 3.0 3 WVDC AT + 85 °C 0.5 1.0 2.0 3.0 4 WVDC AT + 85 °C 0.5 1.0 2.0 3.0 6 WVDC AT + 85 °C 0.5 1.0 2.0 3.0 10 WVDC AT + 85 °C 0.5 1.0 2.0 3.0 15 WVDC AT + 85 °C 0.5 2.0 3.0 20 WVDC AT + 85 °C 0.5 1.0 1.0 2.0 3.0 25 WVDC AT + 85 °C 0.5 1.0 2.0 3.0 35 WVDC AT + 85 °C 0.5 0.5 0.5 1.0 1.0 1.0 2.0 50 WVDC AT + 85 °C 3.0 CASE CODE PART NUMBER N1 N2 N3 N4 TC4.7-2N1 (1)M TC15-2N2 (1)M TC47-2N3 (1)M TC68-2N4 (1)M N1 N2 N3 N4 TC3.3-3N1 (1)M TC10-3N2 (1)M TC33-3N3 (1)M TC47-3N4 (1)M N1 N2 N3 N4 TC2.2-4N1 (1)M TC6.8-4N2 (1)M TC22-4N3 (1)M TC33-4N4 (1)M N1 N2 N3 N4 TC1.5-6N1 (1)M TC4.7-6N2 (1)M TC15-6N3 (1)M TC22-6N4 (1)M N1 N2 N3 N4 TC1.0-10N1 (1)M TC3.3-10N2 (1)M TC10-10N3 (1)M TC15-10N4 (1)M N1 N3 N4 TC.68-15N1 (1)M TC6.8-15N3 (1)M TC10-15N4 (1)M N1 N2 N2 N3 N4 TC.47-20N1 (1)M TC1.5-20N2 (1)M TC2.2-20N2 (1)M TC4.7-20N3 (1)M TC6.8-20N4 (1)M N1 N2 N3 N4 TC.33-25N1 (1)M TC1.0-25N2 (1)M TC3.3-25N3 (1)M TC4.7-25N4 (1)M N1 N1 N1 N2 N2 N2 N3 TC.10-35N1 (1)M TC.15-35N1 (1)M TC.22-35N1 (1)M TC.33-35N2 (1)M TC.47-35N2 (1)M TC.68-35N2 (1)M TC1.0-35N3 (1)M N4 TC2.2-50N4 (1)M For technical questions, contact: tantalum@vishay.com Document Number: 43005 Revision: 12-Sep-07 TC Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague MARKING All other case sizes have color dot marking: TC Capacitors case sizes C3 - C6 and N2 - N4 are print marked: - Capacitance is in picofarads - 1st and 2nd digits are significant figures - 3rd digit indicates the number of zeros. Capacitance Color Digit Black 0 3rd dot indicates the number of zeros. Brown 1 Color dot location is shown on the dimensional sketches. Red 2 Orange 3 Yellow 4 Green 5 Blue 6 In picofarads, indicated by 3 dots. 1st and 2nd dot give the significant digits. Black dot is omitted on black sleeve. Capacitance Tolerance Color Tolerance Is indicated by a dot on the side of the case. Black dot is omitted. Gold ±5% Violet 7 Silver ± 10 % Grey 8 None ± 20 % White 9 None + 40 %/- 20 % e.g. Yellow-Violet-Green = 4 700 000 pF The positive lead is indicated by a color dot of red epoxy on the unit. = 4.7 µF Document Number: 43005 Revision: 12-Sep-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 89 TC Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague PERFORMANCE AND RELIABILITY The capacitors are tested in accordance with MIL-PRF-49137, with specific requirements as follows: IMPEDANCE VS. FREQUENCY Temperature Stability: When tested per MIL-PRF-49137/6, capacitance shall be within ± 15 % at - 55 °C and 85 °C, and ± 10 % at 25 °C after exposure to temperature extremes. DF shall be within 200 % of initial limit at - 55 °C, 150 % of initial limit at 85 °C, and meet the initial at 25 °C. DCL shall be within 10 x initial limit at 85 °C, and meet the initial limit at 25 °C. Life: (per Method 108 of MIL-STD-202) after 1000 h at 85 °C and rated voltage; capacitance shall be within ± 10 % of initial limit, DF within initial limits, and leakage within 200 % of initial limit. Surge Voltage: (per MIL-PRF-49317) After 1000 cycles at 85 °C and 1.3 x WVDC; capacitance shall be within ± 10 % of initial limit, DF and leakage within initial limits. Resistance to Soldering Heat: (per Method 210 of MIL-STD-202, Condition B) After immersion in 260 °C molten solder to within a 1/4" of the body of the unit, there shall be no evidence of mechanical or electrical degradation. 5K (MFD-WVDC) 2K 1K 0. 04 7 µF -2 0V 0. 0 0. 4 7 04 µ 7 F µF -2 -3 0 V 5V 0.0 0.0 47 47 µF µF -50 -3 V 5V 4.7 4.7 µF µF -10 -2 V 0V 500 200 IMPEDANCE Ω Moisture Resistance: (per Method 106 of MIL-STD-202) After 10 cycles of 24 h at 25 °C to 65 °C and 80 - 98 % RH; capacitance shall be within ± 15 % of initial value, DF within 1.5 x initial limit and leakage within 3 x initial limit. 10K 100 50 20 10 5.0 2.0 4.7 µF -2 1.0 0V 0.5 0.2 Solderability: (per Method 208 of MIL-STD-202) After dipping leads in 235 °C molten solder to within 0.125" of the body of the unit, the solder shall cover 95 % of the lead surface. Terminal Strength: (per Method 211 of MIL-STD-202) After the following test there shall be no loosening of the terminals or permanent damage to the terminals. Test Condition A: (Pull Test) 0.010" leads withstand 1 pound, 0.016" leads 2 pounds and 0.007" leads 1/2 pound. Test Condition C: (Bend Test) All leads shall withstand 3 - 90° bends with a 1/2 pound applied force. 0.1 100 500 1 Hz 2 kHz 5 10 20 50 100 FREQUENCY 500 1 2 kHz 5 10 MHz LEAKAGE CURRENT - TEMPERATURE 1.0 (MFD-WVDC) CHANGE IN CAPACITANCE % + 10 (MFD-WVDC) +5 SP 0 0 10 µF 0 -1 - 10 - 40 CI I V TY I AT ON F 0µ 10 AL PIC 1 -5 E SP EC C FI FI - 10 TI CA D.C. LEAKAGE CURRENT (µA) CAPACITANCE VS. TEMPERATURE 0 -1 µH - V V 20 ON 1 µF-20 V 100 µF-10 V 0.1 0.01 + 25 + 85 + 100 - 40 - 10 TEMPERATURE °C www.vishay.com 90 For technical questions, contact: tantalum@vishay.com 0 + 20 + 85 TEMPERATURE °C Document Number: 43005 Revision: 12-Sep-07 STC Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar FEATURES • • • • • • • • Subminiature package size and light weight Rectangular case with axial or radial leads 2 to 35 VDC 0.1 µF to 470 µF Operating temperature range: - 55 °C to + 125 °C High stability and reliability Tested in accordance with MIL-PRF-49137 Unique and comprehensive custom design capability ELECTRICAL CHARACTERISTICS Operating temperature range: - 55 °C to + 125 °C Capacitance: Measured at 120 Hz and 25 °C with a maximum of 2.2 VDC bias and 1.0 Vrms signal. Capacitance Tolerance: Standard tolerance is ± 20 % for ratings 0.1 µF and above, and + 40, - 20 % for ratings below 0.1 µF. Special tolerances are also available. Dissipation Factor: When measured simultaneously with capacitance, DF shall not exceed the value shown in the ratings tables. DC Leakage Current (DCL Max.): When measured with DC voltage applied through a 1000 Ω resistor for 5 min, DC leakage (µA) shall not exceed: At 25 °C: Leakage current shall not exceed the values listed in the Standard Ratings Tables At 85 °C: Leakage current shall not exceed 10 times the values listed in the Standard Ratings Tables At 125 °C and 66 % of Rated Voltage: Leakage current shall not exceed 15 times the values listed in the Standard Ratings Tables Operating Voltage: Full working voltage up to 85 °C. From 85 °C to 125 °C working voltage derates linearly to 66 % of the 85 °C working voltage APPLICATIONS • Hearing aids • Portable communications • Space/avionics • Laptop computers MECHANICAL SPECIFICATIONS Solder coated nickel leads (type N32 per MIL-STD-1276) are standard on all case sizes Leads are weldable and/or solderable Special leads are available on request (e.g. bare nickel, gold plated nickel or ribbon leads) Lead length is 1 1/2" [38.1 mm] minimum on nonpolar parts On polar parts the negative lead is 1 1/4" [31.8 mm] minimum and the positive lead is 1 1/2" [38.1 mm] minimum ORDERING INFORMATION STC MODEL 1.0 CAPACITANCE IN µF 35 DC VOLTAGE RATING AT + 85 °C C2 CASE CODE C = Polar N = Non-polar A (1) LEAD CONFIGURATION A = Axial R = Radial M CAPACITANCE TOLERANCE E = + 40, - 20 % M = ± 20 % K = ± 10 % J= ±5% Example of Part Number Code: STC1.0-35C2AM Note: (1) To complete part number in rating tables, add A or R. Change suffix if special capacitance tolerance is required. Document Number: 43006 Revision: 10-Dec-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 91 STC Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague DIMENSIONS in inches [millimeters] AXIAL POLAR STYLE RADIAL T T RED EPOXY POLARITY DOT W W d (+) 3RD DOT 3RD DOT 2ND DOT 2ND DOT L L 1ST DOT 1ST DOT TOLERANCE DOT TOLERANCE DOT d d (+) (-) E THE 3RD DOT IS ON THE END OF THE CX SIZE L MAX. CASE CODE W MAX. T MAX. E TOL. ± E d CX 0.075 [1.91] 0.050 [1.27] 0.040 [1.02] 0.030 [0.76] 0.015 [0.38] 0.007 [0.18] C0 0.100 [2.54] 0.050 [1.27] 0.040 [1.02] 0.030 [0.76] 0.015 [0.38] 0.007 [0.18] C1 0.125 [3.18] 0.070 [1.78] 0.040 [1.02] 0.050 [1.27] 0.015 [0.38] 0.010 [0.25] C2 0.165 [4.19] 0.120 [3.05] 0.070 [1.78] 0.100 [2.54] 0.020 [0.51] 0.010 [0.25] C3 0.225 [5.72] 0.185 [4.70] 0.075 [1.91] 0.150 [3.81] 0.020 [0.51] 0.010 [0.25] 0.016 [0.41] C4 0.290 [7.37] 0.220 [5.59] 0.110 [2.79] 0.180 [4.57] 0.025 [0.64] C5 0.310 [7.87] 0.230 [5.84] 0.130 [3.30] 0.200 [[5.08] 0.025 [0.64] 0.016 [0.41] C6 0.475 [12.07] 0.375 [9.53] 0.150 [3.81] 0.300 [7.62] 0.025 [0.64] 0.016 [0.41] NON POLAR STYLE AXIAL RADIAL T T W d W TOLERANCE DOT TOLERANCE DOT 2ND DOT 2ND DOT LA LR 1ST DOT 1ST DOT 3RD DOT 3RD DOT d E CASE CODE LA MAX. LR MAX. W MAX. T MAX. E MAX. E TOL. ± d N1 0.220 [5.59] 0.180 [4.57] 0.125 [3.18] 0.125 [3.18] 0.100 [2.54] 0.020 [0.51] 0.010 [0.25] N2 0.280 [7.11] 0.240 [6.10] 0.140 [3.56] 0.180 [4.57] 0.100 [2.54] 0.025 [0.64] 0.010 [0.25] N3 0.370 [9.40] 0.315 [8.00] 0.180 [4.57] 0.220 [5.59] 0.150 [3.81] 0.025 [0.64] 0.016 [0.41] N4 0.390 [9.91] 0.335 [8.51] 0.230 [5.84] 0.230 [5.84] 0.180 [4.57] 0.025 [0.64] 0.016 [0.41] www.vishay.com 92 For technical questions, contact: tantalum@vishay.com Document Number: 43006 Revision: 10-Dec-07 STC Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague STANDARD RATINGS - POLAR CAPACITORS CAPACITANCE (µF) MAX DF (%) 0.0022 0.0033 0.0047 0.0068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 2.2 6.8 100 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 1.5 22 68 100 10 10 10 10 1.0 4.7 10 15 47 68 220 470 10 10 8 8 8 8 15 15 0.68 3.3 33 47 150 330 10 8 6 6 10 15 0.47 1.5 2.2 6.8 22 33 100 220 10 6 6 6 6 6 8 6 1.0 4.7 15 22 68 150 6 6 6 6 6 10 MAX. DCL AT + 25 °C (µA) 2 WVDC AT + 85 °C 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 2.0 3 WVDC AT + 85 °C 0.5 1.0 2.0 3.0 4 WVDC AT + 85 °C 0.5 0.5 1.0 1.0 2.0 3.0 9.0 10.0 6 WVDC AT + 85 °C 0.5 0.5 2.0 3.0 9.0 10.0 10 WVDC AT + 85 °C 0.5 0.5 0.5 1.0 2.0 3.0 9.0 0.5 15 WVDC AT + 85 °C 0.5 1.0 2.0 3.0 6.0 10.0 CASE CODE PART NUMBER CX CX CX CX CX CX CX CX CX CX CX CX CX C0 C1 C3 STC.0022-2CX (1)E STC.0033-2CX (1)E STC.0047-2CX (1)E STC.0068-2CX (1)E STC.10-2CX (1)M STC.15-2CX (1)M STC.22-2CX (1)M STC.33-2CX (1)M STC.47-2CX (1)M STC.68-2CX (1)M STC1.0-2CX (1)M STC1.5-2CX (1)M STC2.2-2CX (1)M STC2.2-2C0 (1)M STC6.8-2C1 (1)M STC100-2C3 (1)M C0 C2 C3 C4 STC1.5-3C0 (1)M STC22-3C2 (1)M STC68-3C3 (1)M STC100-3C4 (1)M C0 C1 C2 C2 C3 C4 C5 C6 STC1.0-4C0 (1)M STC4.7-4C1 (1)M STC10-4C2 (1)M STC15-4C2 (1)M STC47-4C3 (1)M STC68-4C4 (1)M STC220-4C5 (1)M STC470-4C6 (1)M C0 C1 C3 C4 C5 C6 STC.68-6C0 (1)M STC3.3-6C1 (1)M STC33-6C3 (1)M STC47-6C4 (1)M STC150-6C5 (1)M STC330-6C6 (1)M C0 C1 C1 C2 C3 C4 C5 C6 STC.47-10C0 (1)M STC1.5-10C1 (1)M STC2.2-10C1 (1)M STC6.8-10C2 (1)M STC22-10C3 (1)M STC33-10C4 (1)M STC100-10C5 (1)M STC220-10C6 (1)M C1 C2 C3 C4 C5 C6 STC1.0-15C1 (1)M STC4.7-15C2 (1)M STC15-15C3 (1)M STC22-15C4 (1)M STC68-15C5 (1)M STC150-15C6 (1)M Note: Add A for axial, R for radial (1) Document Number: 43006 Revision: 10-Dec-07 For technical questions, contact: tantalum@vishay.com www.vishay.com 93 STC Vishay Sprague Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar STANDARD RATINGS - POLAR CAPACITORS CAPACITANCE (µF) MAX DF (%) 0.68 3.3 6.8 10 15 47 100 6 6 6 6 6 6 10 0.47 2.2 3.3 4.7 10 15 22 33 68 6 6 6 6 6 6 6 6 6 0.33 0.68 1.0 1.5 6 6 6 6 MAX. DCL AT+ 25 °C (µA) 20 WVDC AT + 85 °C 0.5 1.0 2.0 2.0 3.0 6.0 10.0 25 WVDC AT + 85 °C 0.5 1.0 2.0 2.0 3.0 6.0 6.0 6.0 10.0 35 WVDC AT + 85 °C 0.5 1.0 1.0 1.0 CASE CODE PART NUMBER C1 C2 C3 C3 C4 C5 C6 STC.68-20C1 (1)M STC3.3-20C2 (1)M STC6.8-20C3 (1)M STC10-20C3 (1)M STC15-20C4 (1)M STC47-20C5 (1)M STC100-20C6 (1)M C1 C2 C3 C3 C4 C5 C5 C5 C6 STC.47-25C1 (1)M STC2.2-25C2 (1)M STC3.3-25C3 (1)M STC4.7-25C3 (1)M STC10-25C4 (1)M STC15-25C5 (1)M STC22-25C6 (1)M STC33-25C5 (1)M STC68-25C6 (1)M C1 C2 C2 C2 STC.33-35C1 (1)M STC.68-35C2 (1)M STC1.0-35C2 (1)M STC1.5-35C2 (1)M CASE CODE PART NUMBER N1 STC10-2N1*M N2 N3 N4 STC33-3N2*M STC47-3N3*M STC100-3N4*M N1 N2 N3 N4 STC6.8-4N1*M STC22-4N2*M STC33-4N3*M STC68-4N4*M N1 N2 N3 N4 STC4.7-6N1*M STC15-6N2*M STC22-6N3*M STC47-6N4*M N1 N2 N3 N4 STC3.3-10N1*M STC10-10N2*M STC15-10N3*M STC33-10N4*M Note: (1) Add A for axial, R for radial STANDARD RATINGS - NON-POLAR CAPACITORS CAPACITANCE (µF) MAX DF (%) 10 10 33 47 100 10 8 10 6.8 22 33 68 8 8 8 8 4.7 15 22 47 6 6 6 6 3.3 10 15 33 6 6 6 6 MAX. DCL AT + 25 °C (µA) 2 WVDC AT + 85 °C 1.0 3 WVDC AT + 85 °C 2.0 3.0 6.0 4 WVDC AT + 85 °C 1.0 2.0 3.0 6.0 6 WVDC AT + 85 °C 1.0 2.0 3.0 6.0 10 WVDC AT + 85 °C 1.0 2.0 3.0 6.0 Note: Add A for axial, R for radial (1) www.vishay.com 94 For technical questions, contact: tantalum@vishay.com Document Number: 43006 Revision: 10-Dec-07 STC Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague STANDARD RATINGS - NON-POLAR CAPACITORS CAPACITANCE (µF) MAX. DF (%) 2.2 6.8 10 22 6 6 6 6 1.5 4.7 6.8 15 6 6 6 6 1.0 2.2 3.3 4.7 10 6 6 6 6 6 0.68 6 MAX. DCL AT + 25 °C (µA) 15 WVDC AT + 85 °C 1.0 2.0 3.0 6.0 20 WVDC AT + 85 °C 1.0 2.0 3.0 6.0 25 WVDC AT + 85 °C 1.0 2.0 2.0 3.0 6.0 35 WVDC AT + 85 °C 1.0 CASE CODE PART NUMBER N1 N2 N3 N4 STC2.2-15N1*M STC6.8-15N2*M STC10-15N3*M STC22-15N4*M N1 N2 N3 N4 STC1.5-20N1*M STC4.7-20N2*M STC6.8-20N3*M STC15-20N4*M N1 N2 N2 N3 N4 STC1.0-25N1*M STC2.2-25N2*M STC3.3-25N2*M STC4.7-25N3*M STC10-25N4*M N1 STC.68-35N1*M Note: Add A for axial, R for radial (1) MARKING All other case sizes are have color dot marking: STC Capacitors case sizes C3 - C6 and N2 - N4 are print marked: - Capacitance is in picofarads - 1st and 2nd digits are significant figures - 3rd digit indicates the number of zeros. Capacitance In picofarads, indicated by 3 dots. 1st and 2nd dot give the significant digits. 3rd dot indicates the number of zeros. Color dot location is shown on the dimensional sketches. Black dot is omitted on black sleeve. Tolerance Color Digit Black 0 Brown 1 Red 2 Orange 3 Yellow 4 Green 5 Blue 6 Capacitance Tolerance Color Is indicated by a dot on the side of the case. Black dot is omitted. Gold ±5% Violet 7 Silver ± 10 % Grey 8 None ± 20 % White 9 None + 40 %/- 20 % e.g. Yellow-Violet-Green = 4 700 000 pf The positive lead is indicated by a color dot of red epoxy on the unit. Document Number: 43006 Revision: 10-Dec-07 For technical questions, contact: tantalum@vishay.com = 4.7 µF www.vishay.com 95 STC Subminiature, Leaded Solid Tantalum Capacitors Polar or Non-Polar Vishay Sprague PERFORMANCE AND RELIABILITY The capacitors are tested in accordance with MIL-PRF49137, with specific requirements as follows: IMPEDANCE VS. FREQUENCY Temperature Stability: When tested per MIL-PRF-49137/ 6, capacitance shall be within ± 15 % at - 55 °C and 85 °C, and ± 10 % at 25 °C after exposure to temperature extremes. DF shall be within 200 % of initial limit at - 55 °C, 150 % of initial limit at 85 °C, and meet the initial at 25 °C. DCL shall be within 10 x initial limit at 85 °C, and meet the initial limit at 25 °C. Life: (per Method 108 of MIL-STD-202) after 1000 h at 85 °C and rated voltage; capacitance shall be within ± 10 % of initial limit, DF within initial limits, and leakage within 200 % of initial limit. Surge Voltage: (per MIL-PRF-49317) After 1000 cycles at 85 °C and 1.3 x WVDC; capacitance shall be within ± 10 % of initial limit, DF and leakage within initial limits. Resistance to Soldering Heat: (per Method 210 of MIL-STD-202, Condition B) After immersion in 260 °C molten solder to within a 1/4” of the body of the unit, there shall be no evidence of mechanical or electrical degradation. Solderability: (per Method 208 of MIL-STD-202) After dipping leads in 235 °C molten solder to within 0.125" of the body of the unit, the solder shall cover 95 % of the lead surface. CAPACITANCE VS. TEMPERATURE CHANGE IN CAPACITANCE % + 10 (MFD-WVDC) +5 SP 0V 0 0 10 µF -1 - 10 - 40 CI I TY I AT ON F 0µ 10 AL PIC 1 -5 E SP EC C FI FI - 10 TI CA V 0 -1 µH 0V -2 ON (MFD-WVDC) 2K 1K 0. 04 7 µF -2 0V 0. 0. 04 04 7 µ 7 F µF -2 -3 0 V 5V 0.0 0.0 47 47 µF µF -50 -3 V 5V 4. 4.7 7 µF µF -10 -2 V 0V 500 200 100 50 20 10 5.0 2.0 4.7 0V 0.5 0.2 0.1 100 500 1 Hz 2 5 kHz 10 20 50 100 FREQUENCY 500 1 kHz 2 5 10 MHz LEAKAGE CURRENT - TEMPERATURE 1.0 (MFD-WVDC) 1 µF-20 V 100 µF-10 V 0.1 0.01 + 25 + 85 + 100 - 40 TEMPERATURE °C www.vishay.com 96 µF -2 1.0 D.C. LEAKAGE CURRENT (µA) Terminal Strength: (per Method 211 of MIL-STD-202) After the following test there shall be no loosening of the terminals or permanent damage to the terminals. Test Condition A: (Pull Test) 0.010" leads withstand 1 pound, 0.016" leads 2 pounds and 0.007" leads 1/2 pound. Test Condition C: (Bend Test) All leads shall withstand 3 - 90° bends with a 1/2 pound applied force. 5K IMPEDANCE Ω Moisture Resistance: (per Method 106 of MIL-STD-202) After 10 cycles of 24 h at 25 °C to 65 °C and 80 - 98 % RH; capacitance shall be within ± 15 % of initial value, DF within 1.5 x initial limit and leakage within 3 x initial limit. 10K For technical questions, contact: tantalum@vishay.com - 10 0 + 20 + 85 TEMPERATURE °C Document Number: 43006 Revision: 10-Dec-07 Contents 173D .............................. 98 790D .............................. 104 199D .............................. 111 Resin Coated 299D .............................. 117 489D, 499D.................... 123 ETPW............................. 131 ETQW ............................ 138 173D Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors, Axial-Leaded, Molded-Case FEATURES • Terminations: Tin/lead (SnPb), 100 % Tin Pb-free (RoHS compliant) Available • Miniature axial-lead capacitors available in RoHS* 5 sizes COMPLIANT • Precision molded in gold colored, flame retardant, thermosetting epoxy resin • Laser marked for improved legibility and tapered end of case provides easy identification of positive terminal • Standard orders are lead taped and reeled; orders under 500 are taped only APPLICATIONS • Designed for high performance automotive, industrial and commercial electronic equipment PERFORMANCE CHARACTERISTICS At + 85 °C: Leakage current shall not exceed 10 times the values listed in the Standard Ratings Tables At + 125 °C: Leakage shall not exceed 15 times the values listed in the Standard Ratings Tables Life Test: Capacitors shall withstand rated DC voltage applied at + 85 °C for 2000 h and for 1000 h applied at + 25 °C derated voltage Following the life test: 1. DCL shall not exceed 125 % of the initial requirements 2. Dissipation Factor shall meet the initial requirement 3. Change in capacitance shall not exceed ± 10 % Operating Temperature: - 55 °C to + 85 °C (To + 125 °C with voltage derating) Capacitance Tolerance: At 120 Hz, + 25 °C. ± 20 %, ± 10 % standard ± 5 % available as special Dissipation Factor: At 120 Hz, + 25 °C. Dissipation factor, as determined from the expression 2πfRC, shall not exceed the values listed in the Standard Ratings Tables DC Leakage Current (DCL Max.): At + 25 °C: Leakage current shall not exceed the values listed in the Standard Ratings Tables ORDERING INFORMATION 173D MODEL 335 CAPACITANCE X9 CAPACITANCE TOLERANCE This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. X0 = ± 20 % X9 = ± 10 % *X5 = ± 5 % *special order 006 DC VOLTAGE RATING AT + 85 °C U CASE CODE W PACKAGING E3 ROHS COMPLIANT This is expressed in volts. To complete the three-digit block, zeros precede the voltage rating. See Ratings and Case Codes Table W = Tape and Reel Blank =Ammo Pack E3 = 100 % tin termination (RoHS compliant) Blank = SnPb termination DIMENSIONS in inches [millimeters] 0.875 [22.23] MIN. L MAX. (-) TINNED SOLID LEADS CASE CODE U V W X Y D MAX. 0.875 [22.23] MIN. (+) TAPERED END IDENTIFIES ANODE D (MAX.) 0.095 [2.41] 0.110 [2.79] 0.180 [4.57] 0.180 [4.57] 0.280 [7.11] L (MAX.) 0.260 [6.60] 0.290 [7.37] 0.345 [8.76] 0.420 [10.67] 0.550 [13.97] LEAD DIAMETER 0.020 [0.51] 0.020 [0.51] 0.020 [0.51] 0.020 [0.51] 0.025 [0.64] * Pb containing terminations are not RoHS compliant, exemptions may apply www.vishay.com 98 For technical questions, contact: tantalum@vishay.com Document Number: 40019 Revision: 15-Jan-08 173D Solid-Electrolyte TANTALEX® Capacitors, Axial-Leaded, Molded-Case Vishay Sprague STANDARD RATINGS MAX. DCL AT + 25 °C (µA) 2 WVDC AT + 85 °C, SURGE = 2.5 V . . . 1.5 WVDC AT + 125 °C, SURGE = 1.8 V 173D685X0002U 173D685X9002U 0.5 173D825X9002U 0.5 173D106X0002U 173D106X9002U 0.5 173D126X9002V 0.5 173D156X0002V 173D156X9002V 0.5 173D186X9002V 0.5 173D226X0002V 173D226X9002V 0.5 173D276X9002V 0.5 173D336X0002V 173D336X9002V 0.5 173D396X9002W 0.6 173D476X0002W 173D476X9002W 0.8 173D566X9002W 0.9 173D686X0002W 173D686X9002W 1.1 4 WVDC AT + 85 °C, SURGE = 5 V . . . 2.5 WVDC AT + 125 °C, SURGE = 3 V 173D475X0004U 173D475X9004U 0.5 173D565X9004U 0.5 173D685X0004U 173D685X9004U 0.5 173D825X9004V 0.5 173D106X0004V 173D106X9004V 0.5 173D126X9004V 0.5 173D156X0004V 173D156X9004V 0.5 173D186X9004V 0.6 173D226X0004V 173D226X9004V 0.7 173D276X9004W 0.9 173D336X0004W 173D336X9004W 1.1 173D396X9004W 1.2 173D476X0004W 173D476X9004W 1.5 173D566X9004X 1.5 173D686X0004X 173D686X9004X 2.2 6 WVDC AT + 85 °C, SURGE = 8 V . . . 4 WVDC AT + 125 °C, SURGE = 5 V 173D335X0006U 173D335X9006U 0.5 173D395X9006U 0.5 173D475X0006U 173D475X9006U 0.5 173D565X9006V 0.5 173D685X0006V 173D685X9006V 0.5 173D825X9006V 0.5 173D106X0006V 173D106X9006V 0.5 173D126X9006V 0.6 173D156X0006V 173D156X9006V 0.7 173D186X9006W 0.9 173D226X0006W 173D226X9006W 1.1 173D276X9006W 1.3 173D336X0006W 173D336X9006W 1.5 173D396X9006X 1.9 173D476X9006X 173D476X9006X 2.3 173D566X9006X 2.7 173D686X0006X 173D686X9006X 3.3 173D826X9006Y 3.9 173D107X0006Y 173D107X9006Y 4.8 173D127X9006Y 5.0 173D157X0006Y 173D157X9006Y 5.0 173D187X9006Y 8.6 173D227X0006Y 173D227X9006Y 10.0 173D277X9006Y 10.0 173D337X0006Y 173D337X9006Y 10.0 CAPACITANCE (µF) CASE CODE 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 U U U V V V V V V W W W W 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 U U U V V V V V V W W W W X X 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 120.0 150.0 180.0 220.0 270.0 330.0 U U U V V V V V V W W W W X X X X Y Y Y Y Y Y Y Y PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % MAX. DF AT + 25 °C 120 Hz (%) 10 10 10 10 10 10 10 10 10 10 10 10 10 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 8 8 8 8 8 Note: Part number should include “X5”; for ± 5 % units (special order) (1) Document Number: 40019 Revision: 15-Jan-08 For technical questions, contact: tantalum@vishay.com www.vishay.com 99 173D Solid-Electrolyte TANTALEX® Capacitors, Axial-Leaded, Molded-Case Vishay Sprague STANDARD RATINGS MAX. DCL AT + 25 °C (µA) 10 WVDC AT + 85 °C, SURGE = 13 V . . . 7 WVDC AT + 125 °C, SURGE = 9 V 173D225X0010U 173D225X9010U 0.5 173D275X9010U 0.5 173D335X0010U 173D335X9010U 0.5 173D395X9010V 0.5 173D475X0010V 173D475X9010V 0.5 173D565X9010V 0.5 173D685X0010V 173D685X9010V 0.5 173D825X9010V 0.7 173D106X0010V 173D106X9010V 0.8 173D126X9010W 1.0 173D156X0010W 173D156X9010W 1.2 173D186X9010W 1.4 173D226X0010W 173D226X9010W 1.5 173D276X9010X 2.2 173D336X0010X 173D336X9010X 2.6 173D396X9010X 3.1 173D476X0010X 173D476X9010X 3.8 173D566X9010Y 4.4 173D686X0010Y 173D686X9010Y 5.0 173D826X9010Y 5.0 173D107X0010Y 173D107X9010Y 8.0 173D127X9010Y 9.6 173D157X0010Y 173D157X9010Y 10.0 173D187X9010Y 10.0 173D227X0010Y 173D227X9010Y 10.0 15 WVDC AT + 85 °C, SURGE = 20 V . . . 10 WVDC AT + 125 °C, SURGE = 12 V 173D155X0015U 173D155X9015U 0.5 173D185X9015U 0.5 173D225X0015U 173D225X9015U 0.5 173D275X9015V 0.5 173D335X0015V 173D335X9015V 0.5 173D395X9015V 0.5 173D475X0015V 173D475X9015V 0.6 173D565X9015V 0.7 173D685X0015V 173D685X9015V 0.8 173D825X9015W 1.0 173D106X0015W 173D106X9015W 1.2 173D126X9015W 1.4 173D156X0015W 173D156X9015W 1.5 173D186X9015X 2.2 173D226X9015X 173D226X9015X 2.6 173D276X9015X 3.2 173D336X0015X 173D336X9015X 4.0 173D396X9015Y 4.7 173D476X0015Y 173D476X9015Y 5.0 173D566X9015Y 6.7 173D686X0015Y 173D686X9015Y 8.2 173D826X9015Y 9.8 173D107X0015Y 173D107X9015Y 10.0 173D127X9015Y 10.0 173D157X0015Y 173D157X9015Y 10.0 CAPACITANCE (µF) CASE CODE 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 120.0 150.0 180.0 220.0 U U U V V V V V V W W W W X X X X Y Y Y Y Y Y Y Y 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 120.0 150.0 U U U V V V V V V W W W W X X X X Y Y Y Y Y Y Y Y PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % MAX. DF AT+ 25 °C 120 Hz (%) 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 8 8 8 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 8 8 8 8 Note: (1) Part number should include “X5”; for ± 5 % units (special order) www.vishay.com 100 For technical questions, contact: tantalum@vishay.com Document Number: 40019 Revision: 15-Jan-08 173D Solid-Electrolyte TANTALEX® Capacitors, Axial-Leaded, Molded-Case Vishay Sprague STANDARD RATINGS MAX. DCL AT+ 25 °C (µA) 20 WVDC AT + 85 °C, SURGE = 26 V . . . 13 WVDC AT + 125 °C, SURGE = 16 V 173D105X0020U 173D105X9020U 0.5 173D125X9020U 0.5 173D155X0020U 173D155X9020U 0.5 173D185X9020V 0.5 173D225X0020V 173D225X9020V 0.5 173D275X9020V 0.5 173D335X0020V 173D335X9020V 0.5 173D395X9020V 0.6 173D475X0020V 173D475X9020V 0.8 173D565X9020W 0.9 173D685X0020W 173D685X9020W 1.1 173D825X9020W 1.3 173D106X0020W 173D106X9020W 1.6 173D126X9020X 1.9 173D156X0020X 173D156X9020X 2.4 173D186X9020X 2.9 173D226X0020X 173D226X9020X 3.5 173D276X9020Y 4.3 173D336X0020Y 173D336X9020Y 5.0 173D396X9020Y 6.2 173D476X0020Y 173D476X9020Y 7.5 173D566X9020Y 8.9 173D686X0020Y 173D686X9020Y 10.0 173D826X9020Y 10.0 173D107X0020Y 173D107X9020Y 10.0 25 WVDC AT + 85 °C, SURGE = 32 V . . . 17 WVDC AT + 125 °C, SURGE = 21 V 173D474X0025U 173D474X9025U 0.5 173D564X9025U 0.5 173D684X0025U 173D684X9025U 0.5 173D824X9025U 0.5 173D105X0025U 173D105X9025U 0.5 173D125X9025V 0.5 173D155X0025V 173D155X9025V 0.5 173D185X9025V 0.5 173D225X0025V 173D225X9025V 0.5 173D275X9025V 0.5 173D335X0025V 173D335X9025V 0.7 173D395X9025W 0.8 173D475X0025W 173D475X9025W 0.9 173D565X9025W 1.1 173D685X0025W 173D685X9025W 1.4 173D825X9025W 1.5 173D106X0025W 173D106X9025W 1.5 173D126X9025X 2.4 173D156X0025X 173D156X9025X 3.0 173D186X9025Y 3.6 173D226X9025Y 173D226X9025Y 4.4 173D276X9025Y 5.4 173D336X0025Y 173D336X9025Y 6.6 173D396X9025Y 7.8 173D476X0025Y 173D476X9025Y 9.4 CAPACITANCE (µF) CASE CODE 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 56.0 68.0 82.0 100.0 U U U V V V V V V W W W W X X X X Y Y Y Y Y Y Y Y 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 U U U U U V V V V V V W W W W W W X X Y Y Y Y Y Y PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % MAX. DF AT + 25 °C 120 Hz (%) 4 4 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 6 6 6 6 6 6 Note: Part number should include “X5”; for ± 5 % units (special order) (1) Document Number: 40019 Revision: 15-Jan-08 For technical questions, contact: tantalum@vishay.com www.vishay.com 101 173D Solid-Electrolyte TANTALEX® Capacitors, Axial-Leaded, Molded-Case Vishay Sprague STANDARD RATINGS MAX. DCL AT+ 25 °C (µA) 35 WVDC AT + 85 °C, SURGE = 46 V . . . 23 WVDC AT + 125 °C, SURGE = 28 V 173D104X0035U 173D104X9035U 0.5 173D124X9035U 0.5 173D154X0035U 173D154X9035U 0.5 173D184X9035U 0.5 173D224X0035U 173D224X9035U 0.5 173D274X9035U 0.5 173D334X0035U 173D334X9035U 0.5 173D394X9035U 0.5 173D474X0035U 173D474X9035U 0.5 173D564X9035V 0.5 173D684X0035V 173D684X9035V 0.5 173D824X9035V 0.5 173D105X0035V 173D105X9035V 0.5 173D125X9035V 0.5 173D155X0035V 173D155X9035V 0.5 173D185X9035W 0.5 173D225X0035W 173D225X9035W 0.6 173D275X9035W 0.8 173D335X0035W 173D335X9035W 0.9 173D395X9035W 1.1 173D475X0035W 173D475X9035W 1.3 173D565X9035X 1.6 173D685X0035X 173D685X9035X 1.9 173D825X9035X 2.3 173D106X0035X 173D106X9035X 2.8 173D126X9035Y 3.3 173D156X0035Y 173D156X9035Y 4.2 173D186X9035Y 5.0 173D226X0035Y 173D226X9035Y 6.2 173D276X9035Y 7.5 173D336X0035Y 173D336X9035Y 9.2 173D396X9035Y 10.0 173D476X0035Y 173D476X9035Y 10.0 50 WVDC AT + 85 °C, SURGE = 65 V . . . 33 WVDC AT + 125 °C, SURGE = 40 V 173D104X0050U 173D104X9050U 0.5 173D124X9050U 0.5 173D154X0050U 173D154X9050U 0.5 173D184X9050U 0.5 173D224X0050U 173D224X9050U 0.5 173D274X9050U 0.5 173D334X0050V 173D334X9050V 0.5 173D394X9050V 0.5 173D474X0050V 173D474X9050V 0.5 173D564X9050V 0.5 173D684X0050V 173D684X9050V 0.5 173D824X9050V 0.5 173D105X0050V 173D105X9050V 0.5 173D125X9050W 0.5 173D155X0050W 173D155X9050W 0.6 173D185X9050W 0.7 173D225X0050W 173D225X9050W 0.9 173D275X9050X 1.1 173D335X0050X 173D335X9050X 1.3 173D395X9050X 1.6 173D475X0050X 173D475X9050X 1.9 173D565X9050Y 2.2 173D685X0050Y 173D685X9050Y 2.7 173D825X9050Y 3.2 173D106X0050Y 173D106X9050Y 4.0 173D126X9050Y 5.0 173D156X0050Y 173D156X9050Y 6.0 173D186X9050Y 6.0 CAPACITANCE (µF) CASE CODE 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 22.0 27.0 33.0 39.0 47.0 U U U U U U U U U V V V V V V W W W W W W X X X X Y Y Y Y Y Y Y Y 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10.0 12.0 15.0 18.0 U U U U U U V V V V V V V W W W W X X X X Y Y Y Y Y Y Y PART NUMBER (1) CAP. TOL. ± 20 % PART NUMBER (1) CAP. TOL. ± 10 % MAX. DF AT + 25 °C 120 Hz (%) 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 6 6 6 6 6 6 6 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 6 6 6 6 Note: Part number should include “X5”; for ± 5 % units (special order) (1) www.vishay.com 102 For technical questions, contact: tantalum@vishay.com Document Number: 40019 Revision: 15-Jan-08 173D Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors, Axial-Leaded, Molded-Case TAPE AND REEL PACKAGING in inches [millimeters] 13 [330.2] DIA. STANDARD REEL “A” COMPONENT OVERALL LENGTH (1.b) C (1.b) 1.126 TO 3.07 [28.6 TO 78.0] I. D. REEL HUB B (1.a) TAPE SPACING COMPONENT SPACING (4.b) A 1.374 TO 3.626 [34.9 TO 92.1] 0.047 [1.19] MAX. OFF CENTER (1.a) 0.625 ± 0.062 [15.88 ± 1.57] DIA. THRU HOLE 0.125 [3.18] MAX. 0.750 [19.05] “A” LABEL (4.a) 0.250 [6.35] (3.b) 0.750 [19.05] 0.031 [0.79] (3.f) SECTION “A” - ”A” CASE CODE (BOTH SIDES) (3.f) COMPONENT SPACING TAPE SPACING A B UNITS PER AMMOPACK UNITS PER REEL U 4500 V 4000 W, X 2500 Y 500 0.200 ± 0.015 [5.08 ± 3.81] 1000 2.062 ± 0.062 [2.37 ± 1.57] 500 0.400 ± 0.015 STANDARD REEL PACKAGING INFORMATION 1. Component Leads: a. Component leads shall not be bent beyond 0.047" [1.19 mm] maximum from their nominal position when measured from the leading edge of the component lead at the inside tape edge and at the lead egress from the component. b. The “C” dimension shall be governed by the overall length of the reel packaged component. The distance between flanges shall be 0.125" to 0.250" [3.18 mm to 6.35 mm] greater than the overall component length. 2. Orientation: a. All polarized components must be oriented to one direction. The cathode lead tape shall be a color and the anode lead tape shall be white. 3. Reeling: a. Components on any reel shall not represent more than two date codes when date code identification is required. b. Component leads shall be positioned between pairs of 0.250" [6.35 mm] tape. c. The disposable reels have hubs with corrugated fibreboard flanges and core. d. A minimum of 12" [304.8 mm] leader of tape shall be provided before the first and after the last component on the reel. e. 50 to 60 lb. Kraft paper must be wound between layers of components as far as necessary for component protection. Width of paper to be 0.062" to 0.250" [1.57 mm to 6.35 mm] less than the “C” dimension of the reel. Document Number: 40019 Revision: 15-Jan-08 f. Row components must be centered between tapes ± 0.047" [1.19 mm]. In addition, individual components may deviate from center of component row ± 0.031" [0.79]. g. Staples shall not be used for splicing. Not more than 4 layers of tape shall be used in any splice area and no tape shall be offset from another by more than 0.031" [0.79 mm] non-cumulative. Tape splices shall overlap at least 6" [152.4 mm] for butt joints and at least 3" [76.2 mm] for lap joints and shall not be weaker than unspliced tape. Universal splicing clips may also be used. h. Quantity per reel shall be controlled so that tape components and cover shall not extend beyond the smallest dimension of the flange (either across flats or diameter). Once the quantity per reel for each part number has been established, future orders for that part number shall be packaged in that quantity. When order release quantity is less than the established quantity, a standard commercial pack is to be used. i. A maximum of 0.25 % of the components per reel quantity may be missing without consecutive missing components. j. Adequate protection must be provided to prevent physical damage to both reel and components during shipment and storage. 4. Marking: a. Minimum reel and carton marking shall consist of the following: Customer Part Number, Purchase Order No., Quantity, Package Date, Manufacturer's name, Electrical Value, Date Code, Vishay Sprague Part Number and Country of Origin. For technical questions, contact: tantalum@vishay.com www.vishay.com 103 790D Vishay Sprague Resin-Molded, Radial-Lead Solid Tantalum Capacitors FEATURES • Terminations: Tin/lead (SnPb), 100 % Tin (Sn) Pb-free • Four case sizes precisely molded with a flame retardant epoxy resin Available RoHS* • Stand off on all case sizes • Available on tape for automatic insertion equipment (only A- and B-case, C- and D-case on request) • Low leakage current • Low impedance • Extended value ranges available PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 °C to + 125 °C ORDERING INFORMATION 790D 157 X0 006 R 2 P E3 MODEL CAPACITANCE CAPACITANCE TOLERANCE DC VOLTAGE RATING AT + 85 °C CASE CODE STYLE NUMBER PACKAGING ROHS COMPLIANT 790D = Standard and Extended Range Expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros following. X0 = ± 20 % X9 = ± 10 % Expressed in volts. To complete the three-digit block, zeros precede the voltage rating. A decimal point is indicated by an “R” (6R3 = 6.3 V) See Ratings and Case Codes Table Insulated Case (Standard) See Taping Specification B : Bulk G : Ammopack H = 16.5 mm H : Ammopack H = 18.5 mm I : Ammopack Shouldered Leads (A case) X : Reel Pack H = 16.5 mm Y : Reel Pack H = 18.5 mm Z : Reel Pack Shouldered Leads (A case) E3 = 100 % tin termination (RoHS compliant) Blank = SnPb termination DIMENSIONS in millimeters H 0.3 MIN. B + Ø 12 Min. A e CASE CODE A B C D H MAX. (mm) 7.3 10.5 10.5 10.5 A MAX. (mm) 4.7 7.3 12.3 12.3 B MAX. (mm) 4.2 4.8 7.3 12.3 E ± 0.15 (mm) 2.54 5.08 10.16 10.16 Ø 0.05 (+ 10 %) (mm) 0.5 0.5 0.6 0.6 PACKAGING QUANTITIES CASE CODE REEL X/Y AMMO G/H BULK B A B C D 1000 1000 300* 200* 1000 1000 300* 200* 500 250 100 50 * Pb containing terminations are not RoHS compliant, exemptions may apply www.vishay.com 104 For technical questions, contact: eurotant@vishay.com Document Number: 42072 Revision: 10-Dec-07 790D Resin-Molded, Radial-Lead Solid Tantalum Capacitors Vishay Sprague RATINGS AND CASE CODES RATED VOLATAGE UR AT + 85 °C 6.3 V 10 V 16 V 20 V CR µF 25 V 35 V 40 V 50 V 23 V 25 V 32 V CATEGORY VOLTAGE UC AT + 125 °C 4.0 V Std. 6.3 V Ext. Std. 10 V Ext. Std. 13 V Ext. Std. 16 V Ext. Std. Ext. Std. Ext. 0.10 Std. A Ext. Std. A 0.15 A 0.22 A 0.33 A 0.47 A Ext. 0.68 1.0 A 1.5 A 2.2 A 3.3 A 4.7 6.8 A A A 33 B B B B B C C B C C B C C B B B B B 100 330 B B C B B B C B C C 220 B A 15 150 B A A 68 B A 10 47 A A A 22 B D B C C C C C D C C D D Document Number: 42072 Revision: 10-Dec-07 For technical questions, contact: eurotant@vishay.com www.vishay.com 105 790D Vishay Sprague Resin-Molded, Radial-Lead Solid Tantalum Capacitors STANDARD/EXTENDED RATINGS CAPACITANCE CR (µF) CASE CODE PART NUMBER MAX. DCL AT + 25 °C (µA) MAX. DF 120 Hz, AT + 25 °C (%) MAX. IMPEDANCE 100 kHz, AT + 25 °C (Ω) UR = 6.3 V AT + 85 °C, SURGE = 8 V . . . UC = 4 V AT + 125 °C, SURGE = 5 V 6.8 A 790D685X(*)6R3A2(#) 1.0 6 4.0 22.0 A 790D226X(*)6R3A2(#) 1.3 6 2.1 47.0 B 790D476X(*)6R3B2(#) 2.9 6 1.3 68.0 B 790D686X(*)6R3B2(#) 4.2 6 1.3 150.0 C 790D157X(*)6R3C2(#) 9.4 6 0.6 220.0 C 790D227X(*)6R3C2(#) 13.8 6 0.6 330.0 D 790D337X(*)6R3D2(#) 20.7 8 0.4 UR = 10 V AT + 85 °C, SURGE = 13 V . . . UC = 6.3 V AT + 125 °C, SURGE = 8 V 4.7 A 790D475X(*)010A2(#) 1.0 6 4.0 15.0 A 790D156X(*)010A2(#) 1.5 6 2.5 33.0 B 790D336X(*)010B2(#) 3.3 6 1.3 47.0 B 790D476X(*)010B2(#) 4.7 6 1.4 68.0 B 790D686X(*)010B2(#) 6.8 6 1.3 100.0 C 790D107X(*)010C2(#) 10.0 6 0.6 150.0 C 790D157X(*)010C2(#) 15.0 6 0.6 220.0 D 790D227X(*)010D2(#) 22.0 8 0.4 UR = 16 V AT + 85 °C, SURGE = 20 V . . . UC = 10 V AT + 125 °C, SURGE = 13 V 2.2 A 790D225X(*)016A2(#) 1.0 6 5.5 3.3 A 790D335X(*)016A2(#) 1.0 6 4.4 10.0 A 790D106X(*)016A2(#) 1.6 6 2.7 15.0 B 790D156X(*)016B2(#) 2.4 6 1.6 22.0 B 790D226X(*)016B2(#) 3.5 6 1.3 33.0 B 790D336X(*)016B2(#) 5.2 6 1.6 47.0 C 790D476X(*)016C2(#) 7.5 6 0.8 68.0 C 790D686X(*)016C2(#) 10.8 6 0.6 100.0 C 790D107X(*)016C2(#) 16.0 6 0.7 D 790D107X(*)016D2(#) 16.0 6 0.5 100.0 UR = 20 V AT + 85 °C, SURGE = 26 V . . . UC = 13 V AT + 125 °C, SURGE = 16 V 2.2 A 790D225X(*)020A2(#) 1.0 6 5.5 6.8 A 790D685X(*)020A2(#) 1.3 6 3.5 15.0 B 790D156X(*)020B2(#) 3.0 6 1.5 22.0 B 790D226X(*)020B2(#) 4.4 6 2.1 47.0 C 790D476X(*)020C2(#) 9.4 6 0.7 68.0 C 790D686X(*)020C2(#) 13.6 6 0.8 100.0 D 790D107X(*)020C2(#) 20.0 6 0.7 Note: Extended Ratings in bold print (*) Insert 0 for ± 20 % tolerance or 9 for ± 10 % (#) See order information, packaging code www.vishay.com 106 For technical questions, contact: eurotant@vishay.com Document Number: 42072 Revision: 10-Dec-07 790D Resin-Molded, Radial-Lead Solid Tantalum Capacitors Vishay Sprague STANDARD/EXTENDED RATINGS CAPACITANCE CR (µF) CASE CODE PART NUMBER MAX. DCL AT + 25 °C (µA) MAX. DF 120 Hz, AT + 25 °C (%) MAX. IMPEDANCE 100 kHz, AT + 25 °C (Ω) UR = 25 V AT + 85 °C, SURGE = 32 V . . . UC = 16 V AT + 125 °C, SURGE = 20 V 1.5 A 790D155X(*)025A2(#) 1.0 6 6.0 4.7 A 790D475X(*)025A2(#) 1.1 6 4.5 10.0 B 790D106X(*)025B2(#) 2.5 6 1.6 15.0 B 790D156X(*)025B2(#) 3.7 6 2.4 22.0 B 790D226X(*)025B2(#) 5.5 6 2.1 33.0 C 790D336X(*)025C2(#) 8.2 6 0.8 UR = 35 V AT + 85 °C, SURGE = 45 V . . . UC= 23 V AT + 125×C, SURGE = 29 V 3.3 A 790D335X(*)035A2(#) 1.2 6 6.0 10.0 B 790D106X(*)035B2(#) 3.5 6 2.6 C 790D336X(*)035C2(#) 11.6 6 1.3 33.0 UR = 40 V AT + 85 °C, SURGE = 52 V . . . UC = 25 V AT + 125 °C, SURGE = 32 V 0.10 A 790D104X(*)040A2(#) 1.0 6 30 0.33 A 790D334X(*)040A2(#) 1.0 6 14 0.47 A 790D474X(*)040A2(#) 1.0 6 11 1.0 A 790D105X(*)040A2(#) 1.0 6 6.5 1.5 B 790D155X(*)040B2(#) 1.0 6 5.2 2.2 B 790D225X(*)040B2(#) 1.0 6 4.0 3.3 B 790D335X(*)040B2(#) 1.3 6 2.8 4.7 B 790D475X(*)040B2(#) 1.8 6 2.0 6.8 B 790D685X(*)040B2(#) 2.7 6 1.6 10.0 C 790D106X(*)040C2(#) 4.0 6 1.3 15.0 C 790D156X(*)040C2(#) 6.0 6 1.0 C 790D226X(*)040C2(#) 8.8 6 0.8 22.0 UR = 50 V AT + 85 °C, SURGE = 65 V . . . UC = 32 V AT + 125 °C, SURGE = 41 V 0.10 A 790D104X(*)050A2(#) 1.0 6 30 0.15 A 790D154X(*)050A2(#) 1.0 6 24 0.22 A 790D224X(*)050A2(#) 1.0 6 18 1.0 A 790D105X(*)050A2(#) 1.0 6 6.5 1.5 B 790D155X(*)050B2(#) 1.0 6 5.2 2.2 B 790D225X(*)050B2(#) 1.1 6 4.0 3.3 B 790D335X(*)050B2(#) 1.6 6 2.8 4.7 B 790D475X(*)050B2(#) 2.3 6 2.0 6.8 C 790D685X(*)050C2(#) 3.4 6 1.6 10.0 C 790D106X(*)050C2(#) 5.0 6 1.3 15.0 C 790D156X(*)050C2(#) 7.5 6 1.0 Note: Extended Ratings in bold print (*) Insert 0 for ± 20 % tolerance or 9 for ± 10 % (#) See order information, packaging code Document Number: 42072 Revision: 10-Dec-07 For technical questions, contact: eurotant@vishay.com www.vishay.com 107 790D Resin-Molded, Radial-Lead Solid Tantalum Capacitors Vishay Sprague MAXIMUM PERMISSIBLE RIPPLE VOLTAGE AT + 25 °C CASE SIZE “B” 30 20 10 10 7 7 5 3 2 35 50 / V 25 40 V 16 V 10 V 6. V 3V 1 0.7 0.5 0.3 0.2 Urms Urms CASE SIZE “A” 30 20 5 3 2 5 35 0 V /4 2 0V 16 5 V 10 V 6. V 3V 1 0.7 0.5 0.3 0.2 0.1 0.1 0.1K 0.5 1K 5 10K 50 100K 500 0.1K 0.5 1K FREQUENCY IN Hz 10 10 7 7 5 3 2 5 3 2 5 35 0 V / 25 40 16 V V 10 V 6. V 3V 0.5 0.3 0.2 50 100K 500 50 100K 500 CASE SIZE “D” 30 20 Urms Urms CASE SIZE “C” 0.7 10K FREQUENCY IN Hz 30 20 1 5 35 50 / V 25 40 V 16 V 10 V 6. V 3V 1 0.7 0.5 0.3 0.2 0.1 0.1 0.1K 0.5 1K 5 10K 50 100K 500 0.1K 0.5 1K FREQUENCY IN Hz 5 10K FREQUENCY IN Hz TYPICAL CURVES OF IMPEDANCE VS FREQUENCY 30 100 6.3 V 35 V 10 10 Ω Ω 6.8 µF 1 1 µF 47 µF 1 150 µF 6.8 µF 0.1 330 µF 47 µF 22 µF 0.1 1K 10K 100K 1M 10M 100M 1K 10K FREQUENCY IN Hz www.vishay.com 108 For technical questions, contact: eurotant@vishay.com 100K 1M 10M 100M FREQUENCY IN Hz Document Number: 42072 Revision: 10-Dec-07 790D Resin-Molded, Radial-Lead Solid Tantalum Capacitors Vishay Sprague PERFORMANCE CHARACTERISTICS 1. Operating Temperature: - 55 °C to + 85 °C with rated voltage U R applied. + 85 °C to 125 °C with linear voltage derating to category voltage UC (see general information) applied. 2. Capacitance and Tolerance: Capacitance measured at 100 Hz and + 25 °C shall be within the specified tolerance limits of the nominal rating 3. 4. 5. 6. Reverse Voltage: 15 % of rated voltage at + 25 °C 5 % of rated voltage at + 85 °C Surge Voltage: 130 % of UR at + 85 °C 130 % of UC at + 125 °C 7. Life Test: 2000 h at + 85 °C with rated voltage applied 2000 h at + 125 °C. with category voltage applied ΔC/C ≤ 10 % of initial value IL ≤ 1.25 initial limit DF ≤ initial limit 8. Humidity Test: 56 days at + 40 °C, 90 % relative humidity ΔC/C ≤ 8 % of initial value IL ≤ initial limit DF ≤ initial limit • Charge and Discharge Test: 1 million cycles at + 85 °C, 0.5 s charge at UR 0.5 s discharge Series resistance < 0.5 Ω ΔC/C ≤ 5 % of initial value IL ≤ initial limit DF ≤ initial limit 10. Marking: Top: Rating and polarity Front: Type, date code, Sprague trademark Impedance at 100 kHz: Measured at + 20 °C ± 5 °C, impedance shall not exceed the values listed in data sheet. Stability at low and high temperatures : Capacitance change with temperature, dissipation factor and DC leakage current shall not exceed the limits of the following table. TEMP. CAPACITANCE DISSIPATION CHANGE FACTOR CRUR ≤ 1900 IL CRUR > 1900 - 55 °C - 10 % + 25 °C - + 85 °C + 12 % + 125 °C + 15 % 9% 11 % 6% 8% 9% 11 % 12 % Document Number: 42072 Revision: 10-Dec-07 14 % LEAKAGE CURRENT 0.01 CR x UR or 1 µA whichever is greater 0.1 CR x UR or 10 µA whichever is greater 0.125 CR x UR or 12.5 µA whichever is greater For technical questions, contact: eurotant@vishay.com www.vishay.com 109 790D Resin-Molded, Radial-Lead Solid Tantalum Capacitors Vishay Sprague TAPE AND REEL PACKING “A” AND “B” CASES ONLY (MEETS IEC 286-2) REEL P ACKING Δh Ø 20 p SPRAGUE 30 MAX. W2 329 - 331 H0 H W0 W1 AMMOPACKING W t P0 P1 P2 F ØD 191 201 DIRECTION OF UNREEL 41 - 45 320 - 330 CASE CODE TAPE WIDTH DIMENSIONS (mm)/UNITS PER REEL Pitch of component P [mm] 12.7 ± 1.0 Feed hole pitch P0 [mm] 12.7 ± 0.3 Tape width W [mm] 18 (+ 1/- 0.5) Hold down tape width W0 [mm] 5.0 Hole position W1 [mm] 9 (+ 0.75/-0.5) Hold down tape position W2 [mm] 0 (+ 3/-0) Feed hole diameter D0 [mm] 4.0 ± 0.3 Tape thickness T [mm] 0.5 ± 0.2 Component alignment Δh [mm] 0±2 Lead clinch height H0 [mm] 16.0 ± 0.5 Hole center to component center P2 [mm] 6.35 ± 1.3 Lead wire spacing Feed hole center to wire center F [mm] P1 [mm] Case A 2.5 + 0.6, - 0.1 5.1 ± 0.7 Case B 5 + 0.6, - 0.1 3.85 ± 0.7 Case B 5 + 0.6, - 0.1 3.85 ± 0.7 Reel pack options H = 16.5 mm H = 18.5 mm X Y Z X Y Ammopack options H = 16.5 mm H = 18.5 mm G H I G H 1000 1000 1000 Quantity per reel/box www.vishay.com 110 For technical questions, contact: eurotant@vishay.com Document Number: 42072 Revision: 10-Dec-07 199D Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors, Resin-Coated, Radial-Lead FEATURES • Terminations: Tin/lead (SnPb), 100 % tin (Sn) Pb-free • Economy and high performance are combined Available in these radial-lead, solid-electrolyte TANTALEX® capacitor RoHS* • Rugged, reliable capacitors featuring low COMPLIANT leakage current and low dissipation factor • Six miniature case sizes and five lead styles. All case sizes are available in standard tape and reel packaging per EIA-RS-468 • Standard ratings include replacements for Type 196D capacitors • Lead (Pb)-free capacitors have “L” in body marking APPLICATIONS • Suitable for a broad range of consumer, commercial and industrial equipment PERFORMANCE CHARACTERISTICS At + 85 °C: Leakage current shall not exceed 10 times the values listed in the Standard Ratings Tables. At + 125 °C: Leakage shall not exceed 15 times the values listed in the Standard Ratings Tables. Life Test: Capacitors shall withstand rated DC voltage applied at + 85 °C for 1000 h with a circuit resistance not greater than 3 Ω. Following the life test: 1. DCL shall not exceed 125 % of the initial requirements 2. Dissipation Factor shall meet the initial requirement 3. Change in capacitance shall not exceed ± 10 % Operating Temperature: - 55 °C to + 85 °C (To + 125 °C with voltage derating) Capacitance Tolerance: At 120 Hz, + 25 °C, ± 20 %, ± 10 % standard. ± 5 % available as special Dissipation Factor: At 120 Hz, + 25 °C. Dissipation factor, shall not exceed the values listed in the Standard Ratings Tables. DC Leakage Current (DCL Max.): At + 25 °C: Leakage current shall not exceed the values listed in the Standard Ratings Tables. LEAD STYLE CONFIGURATIONS AND DIMENSIONS** (LL = Lead Length) “LONG/SHORT” LL 1, 3 and Y EVEN LL 2, 4 and 5 D D + + 3±1 H “OUTSIDE HOCKEYSTICK” 6 and 7 + + L 6.35 max. D + + H1 L 1.1 ± 0.05 L P P “HAIRPIN” X, Z D D + + H “SNAP- IN” 9 H H L L P P H1 P (1) - WIRE DIAMETER (NOMINAL) 0.020" [0.51 mm] AVAILABLE LEAD STYLES AND PACKAGING TYPES PER CASE SIZE LEAD STYLE/CASE A B C D E F 1 2 Bulk V1 Bulk V1 Reel B1 Ammo A1 3 4 5 Bulk V1 Reel B1 Ammo A1 Bulk V1 Bulk/Reel Ammo 6 Bulk V1 Reel B1 Ammo A1 7 9 X Bulk V1 Reel B1 Ammo A1 Bulk V1 Reel B1 Ammo A1 Bulk V1 Reel B1 Ammo A1 Y Z Bulk V1 Bulk V1 Reel B1 Ammo A1 * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 40020 Revision: 18-Mar-08 For technical questions, contact: tantalum@vishay.com www.vishay.com 111 199D Solid-Electrolyte TANTALEX® Capacitors, Resin-Coated, Radial-Lead Vishay Sprague DIMENSIONS in inches [millimeters] LEAD STYLE 1, 2, 3, 4 CASE D max. A 0.173 [4.40] B 0.197 [5.00] C 0.217 [5.50] D 0.236 [6.00] E 0.339 [8.60] 0.378 [9.60] F P ± 0.024 [0.60] H max. 1, 2, 3 2, 4 L min. L ± 0.118 [3.0] 5, Y P ± 0.03 [0.76] 6 L ± 0.118 [3.0] P ± 0.024 [0.60] H1 max. 0.378 [9.61] 0.280 [7.11] 0.300 [7.62] 0.100 [2.54] 0.360 [9.14] 0.400 [10.16] 0.125 [3.18] 0.591 [15.0] 0.398 [10.12] 0.748 [19.0] 0.748 [19.0] 0.458 [11.64] 0.200 [5.08] 0.492 [12.50] 0.200 [5.08] L - 0.650 [16.50] - 0.240 ± 0.030 [6.1 ± 0.76] 0.498 [12.66] - 0.591 [15.00] - 0.748 [19.00] 1 ± 0.122 [25.4 ± 3.1] DIMENSIONS in inches [millimeters] LEAD STYLE 7, 9 CASE D max. A 0.173 [4.40] B 0.197 [5.00] C 0.217 [5.50] D 0.236 [6.00] 7 P ± 0.024 [0.60] H1 max. 9 L ± 0.03 [0.76] P ± 0.024 [0.60] 0.398 [10.12] 0.458 [11.64] L ± 0.03 [0.76] 0.398 [10.11] 0.378 [9.61] 0.25 [6.35] H1 max. X, Z 0.240 [6.10] 0.200 [5.08] 0.498 [12.66] 0.418 [10.62] 0.478 [12.14] 0.240 [6.10] 0.518 [13.16] D max. H max. H1 max. 0.173 [4.40] 0.280 [7.11] 0.340 [8.64] 0.197 [5.00] 0.300 [7.62] 0.360 [9.14] 0.217 [5.50] 0.360 [9.14] 0.420 [10.67] 0.236 [6.00] 0.400 [10.16] 0.460 [11.68] X Z L ± 0.125 P ± 0.024 P ± 0.024 0.750 [19.05] 0.100 [2.54] 0.125 [3.175] Note: • Lead space measured within 0.05 [1.27] of the body of the capacitor or from the bottom of the crimp ORDERING INFORMATION 199D 475 MODEL CAPACITANCE This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. X9 003 A 1 (1) CAPACITANCE DC VOLTAGE RATING CASE CODE LEAD TOLERANCE AT + 85 °C STYLE X0 = ± 20 % X9 = ± 10 % ** X5 = ± 5 % ** Special Order This is expressed in V. To complete the three-digit block, zeros precede the voltage rating. A decimal point is indicated by an “R” (6R3 = 6.3 V). See Ratings and Case Codes table. V1 E3 PACKAGING RoHS COMPLIANT V1 = Bulk B1 = Tape and reel A1 = Ammo E3 = 100 % tin termination (RoHS compliant) Blank = Tin/lead termination Note: (1) see lead styles table www.vishay.com 112 For technical questions, contact: tantalum@vishay.com Document Number: 40020 Revision: 18-Mar-08 199D Solid-Electrolyte TANTALEX® Capacitors, Resin-Coated, Radial-Lead Vishay Sprague 199D OBSOLETE VS. CURRENT ORDERING CROSS REFERENCE OBSOLETE NEW DESCRIPTION A1 1V1 0.100 SP, UNEVEN STRAIGHT LL, BULK CASES A - D A1 3V1 0.200 SP, UNEVEN STRAIGHT LL, BULK, CASES E, F A1 2V1 0.100 SP, EVEN STRAIGHT LL, BULK, CASES A - D A6 2B1 0.100 SP, EVEN STRAIGHT LL, REEL POSITIVE LEADER, CASES A - D A6 2A1 0.100 SP, EVEN STRAIGHT LL, AMMO, CASES A - D A1 4V1 0.200 SP, EVEN STRAIGHT LL, BULK, CASES E, F A6 4B1 0.200 SP, EVEN STRAIGHT LL, REEL POSITIVE LEADER, CASES E, F A6 4A1 0.200 SP, EVEN STRAIGHT LL, AMMO, CASES E, F A2 5V1 0.125 SP, EVEN STRAIGHT LL, BULK, CASES A - D A7 5B1 0.125 SP, EVEN STRAIGHT LL, REEL POSITIVE LEADER, CASES A - D A7 5A1 0.125 SP, EVEN STRAIGHT LL, AMMO, CASES A - D A2 YV1 0.125 SP, UNEVEN STRAIGHT LL, BULK, CASES A - D B1 XV1 0.100 SP, HAIRPIN LL, BULK CASES A - D B6 XB1 0.100 SP, HAIRPIN LL, REEL POSITIVE LEADER, CASES A - D B6 XA1 0.100 SP, HAIRPIN LL, AMMO, CASES A - D B2 ZV1 0.125 SP, HAIRPIN LL, BULK, CASES A - D B7 ZB1 0.125 SP, HAIRPIN LL, REEL POSITIVE LEADER, CASES A - D B7 ZA1 0.125 SP, HAIRPIN LL, AMMO, CASES A - D E2 6V1 0.200 SP, HOCKEY STICK LL, BULK, CASES A - F E7 6B1 0.200 SP, HOCKEY STICK LL, REEL POSITIVE LEADER, CASES A - F E7 6A1 0.200 SP, HOCKEY STICK LL, AMMO, CASES A - F E3 7V1 0.250 SP, HOCKEY STICK LL, BULK, CASES A - D E8 7B1 0.250 SP, HOCKEY STICK LL, REEL POSITIVE LEADER, CASES A - D E8 7A1 0.250 SP, HOCKEY STICK LL, AMMO, CASES A - D E4 OBSOLETE G2 9V1 0.200 SP, SNAP-IN LL, BULK, CASES A - D G7 9B1 0.200 SP, SNAP-IN LL, REEL POSITIVE LEADER, CASES A - D G7 9A1 0.200 SP, SNAP-IN LL, AMMO, CASES A - D Document Number: 40020 Revision: 18-Mar-08 For technical questions, contact: tantalum@vishay.com www.vishay.com 113 199D Solid-Electrolyte TANTALEX® Capacitors, Resin-Coated, Radial-Lead Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 220.0 330.0 470.0 680.0 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 220.0 330.0 3.3 4.7 6.8 10.0 15.0 22.0 33.0 39.0 47.0 68.0 100.0 150.0 220.0 2.2 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 MAX. DCL at + 25 °C (µA) 3 WVDC AT + 85 °C, SURGE = 3.6 V . . . 2 WVDC AT + 125 °C, SURGE = 2.4 V A 199D475(1)003A(2)(3) 0.5 A 199D685(1)003A(2)(3) 0.5 A 199D106(1)003A(2)(3) 0.5 A 199D156(1)003A(2)(3) 0.5 B 199D226(1)003B(2)(3) 0.6 B 199D336(1)003B(2)(3) 1.0 C 199D476(1)003C(2)(3) 1.4 C 199D686(1)003C(2)(3) 2.0 D 199D107(1)003D(2)(3) 3.0 D 199D157(1)003D(2)(3) 4.0 E 199D227(1)003E(2)(3) 5.0 E 199D337(1)003E(2)(3) 6.0 F 199D477(1)003F(2)(3) 8.0 F 199D687(1)003F(2)(3) 10.0 6.3 WVDC AT + 85 °C, SURGE = 8 V . . . 4 WVDC AT + 125 °C, SURGE = 5 V A 199D475(1)6R3A(2)(3) 0.5 A 199D685(1)6R3A(2)(3) 0.5 B 199D106(1)6R3B(2)(3) 0.6 B 199D156(1)6R3B(2)(3) 0.9 C 199D226(1)6R3C(2)(3) 1.3 C 199D336(1)6R3C(2)(3) 2.0 D 199D476(1)6R3D(2)(3) 2.9 D 199D686(1)6R3D(2)(3) 4.0 D 199D107(1)6R3D(2)(3) 5.0 E 199D157(1)6R3E(2)(3) 6.0 E 199D227(1)6R3E(2)(3) 7.0 F 199D337(1)6R3F(2)(3) 8.0 10 WVDC AT + 85 °C, SURGE = 13 V . . . 7 WVDC AT + 125 °C, SURGE = 9 V A 199D335(1)010A(2)(3) 0.5 A 199D475(1)010A(2)(3) 0.5 B 199D685(1)010B(2)(3) 0.6 B 199D106(1)010B(2)(3) 1.0 C 199D156(1)010C(2)(3) 1.5 C 199D226(1)010C(2)(3) 2.0 D 199D336(1)010D(2)(3) 3.0 D 199D339(1)010D(2)(3) 3.9 D 199D476(1)010D(2)(3) 4.0 D 199D686(1)010D(2)(3) 5.0 E 199D107(1)010E(2)(3) 6.0 E 199D157(1)010E(2)(3) 7.0 F 199D227(1)010F(2)(3) 8.0 16 WVDC AT + 85 °C, SURGE = 20 V . . . 10 WVDC AT + 125 °C, SURGE = 12 V A 199D225(1)016A(2)(3) 0.5 A 199D335(1)016A(2)(3) 0.5 B 199D475(1)016B(2)(3) 0.7 B 199D685(1)016B(2)(3) 1.0 C 199D106(1)016C(2)(3) 1.5 C 199D156(1)016C(2)(3) 2.4 D 199D226(1)016D(2)(3) 3.5 D 199D336(1)016D(2)(3) 4.0 E 199D476(1)016E(2)(3) 5.0 E 199D686(1)016E(2)(3) 6.0 F 199D107(1)016F(2)(3) 7.0 F 199D157(1)016F(2)(3) 8.0 CASE CODE PART NUMBER* MAX. DF at + 25 °C 120 Hz (%) 6 6 8 8 8 8 8 8 10 10 10 10 10 10 6 6 8 8 8 8 8 8 10 10 10 10 6 6 6 8 8 8 8 8 8 8 10 10 10 6 6 6 6 8 8 8 8 8 8 10 10 Notes: * (1) For capacitance tolerance: (X0 = ± 20 %), (X9 = ± 10 %) or (X5 = 5 %) (2) To specify Lead Style/Spacing/Packaging insert the last three characters in the Part Number. Use the appropriate code shown in the Current Ordering Cross Reference table and explained in the Ordering Information and Lead Styles table. (3) E3 = RoHS compliant 100 % tin leads. Blank or no suffix = standard tin/lead termination. www.vishay.com 114 For technical questions, contact: tantalum@vishay.com Document Number: 40020 Revision: 18-Mar-08 199D Solid-Electrolyte TANTALEX® Capacitors, Resin-Coated, Radial-Lead Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) MAX. DCL at + 25 °C (µA) 20 WVDC AT + 85 °C, SURGE = 26 V . . . 13 WVDC AT + 125 °C, SURGE = 16 V B 199D335(1)020B(2)(3) 0.8 B 199D475(1)020B(2)(3) 1.0 C 199D685(1)020C(2)(3) 1.5 C 199D106(1)020C(2)(3) 2.0 D 199D156(1)020D(2)(3) 2.5 D 199D226(1)020D(2)(3) 3.0 E 199D336(1)020E(2)(3) 4.0 E 199D476(1)020E(2)(3) 5.0 F 199D686(1)020F(2)(3) 6.0 F 199D107(1)020F(2)(3) 7.0 25 WVDC AT + 85 °C, SURGE = 33 V . . . 17 WVDC AT + 125 °C, SURGE = 21 V A 199D105(1)025A(2)(3) 0.5 A 199D155(1)025A(2)(3) 0.5 A 199D225(1)025A(2)(3) 0.5 B 199D335(1)025B(2)(3) 0.8 B 199D475(1)025B(2)(3) 1.0 C 199D685(1)025C(2)(3) 1.5 C 199D106(1)025C(2)(3) 2.5 D 199D156(1)025D(2)(3) 3.0 D 199D226(1)025D(2)(3) 4.0 E 199D336(1)025E(2)(3) 5.0 E 199D476(1)025E(2)(3) 6.0 F 199D686(1)025F(2)(3) 7.0 35 WVDC AT + 85 °C, SURGE = 46 V . . . 23 WVDC AT + 125 °C, SURGE = 28 V A 199D104(1)035A(2)(3) 0.5 A 199D154(1)035A(2)(3) 0.5 A 199D224(1)035A(2)(3) 0.5 A 199D334(1)035A(2)(3) 0.5 A 199D474(1)035A(2)(3) 0.5 A 199D684(1)035A(2)(3) 0.5 A 199D105(1)035A(2)(3) 0.5 A 199D155(1)035A(2)(3) 0.5 B 199D185(1)035B(2)(3) 0.7 B 199D225(1)035B(2)(3) 0.7 B 199D335(1)035B(2)(3) 1.0 C 199D475(1)035C(2)(3) 1.5 D 199D685(1)035D(2)(3) 2.3 D 199D106(1)035D(2)(3) 3.5 E 199D156(1)035E(2)(3) 4.0 E 199D226(1)035E(2)(3) 5.0 F 199D336(1)035F(2)(3) 6.0 F 199D476(1)035F(2)(3) 7.0 50 WVDC AT + 85 °C, SURGE = 65 V . . . 33 WVDC AT + 125 °C, SURGE = 40 V A 199D104(1)050A(2)(3) 0.5 A 199D154(1)050A(2)(3) 0.5 A 199D224(1)050A(2)(3) 0.5 A 199D334(1)050A(2)(3) 0.5 A 199D474(1)050A(2)(3) 0.5 A 199D684(1)050A(2)(3) 0.5 B 199D105(1)050B(2)(3) 0.5 C 199D155(1)050C(2)(3) 0.7 C 199D225(1)050C(2)(3) 1.1 D 199D335(1)050D(2)(3) 1.5 D 199D475(1)050D(2)(3) 2.0 F 199D685(1)050F(2)(3) 3.0 F 199D106(1)050F(2)(3) 4.0 F 199D156(1)050F(2)(3) 5.0 F 199D226(1)050F(2)(3) 6.0 CASE CODE 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 1.0 1.5 2.2 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 0.1 0.15 0.22 0.33 0.47 0.68 1.0 1.5 1.8 2.2 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 0.1 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10.0 15.0 22.0 PART NUMBER* MAX. DF at + 25 °C 120 Hz (%) 6 6 6 8 8 8 8 8 8 10 4 6 6 6 6 6 8 8 8 8 8 8 4 4 4 4 4 4 4 6 6 6 6 6 6 8 8 8 8 8 4 4 4 4 4 4 4 6 6 6 6 6 8 8 8 Notes: * (1) For capacitance tolerance: (X0 = ± 20 %), (X9 = ± 10 %) or (X5 = 5 %) (2) To specify Lead Style/Spacing/Packaging insert the last three characters in the Part Number. Use the appropriate code shown in the Current Ordering Cross Reference table and explained in the Ordering Information and Lead Styles table. (3) E3 = RoHS compliant 100 % tin leads. Blank or no suffix = standard tin/lead termination. Document Number: 40020 Revision: 18-Mar-08 For technical questions, contact: tantalum@vishay.com www.vishay.com 115 199D Solid-Electrolyte TANTALEX® Capacitors, Resin-Coated, Radial-Lead Vishay Sprague STANDARD REEL PACKAGING SPECIFICATIONS PER EIA RS-468 in inches [millimeters] LEAD CONFIGURATION 6.7 LEAD CONFIGURATION 2, 4, 5 LEAD CONFIGURATION X, Z 1.270 [32.26] MAX. 0.118 [3.0] MAX. 0.0354 + 0.030 - 0.020 [8.99 + 0.762 - 0.508] 0.630 ± 0.020 [16.0 ± 0.508] 0.728 ± 0.020 [18.49 ± 0.508] ADHESIVE TAPE LEAD DIAMETER 0.500 ± 0.012 [12.70 ± 0.305] CARRIER TAPE SEE LEAD STYLE/SPACING TABLE FOR LEAD SPACING CASE CODE OBSOLETE LEAD STYLE LEAD SPACING LL MIN. (BULK) A, B, C, D A1, A6 1V1 (Bulk), 2B1 (T and R) 0.100 + 0.024 - 0.016 [2.54 + 0.60 - 0.40] 0.187 [4.7] A, B, C, D B1, B6 XV1 (Bulk), XB1 (T and R) 0.100 + 0.024 - 0.016 [2.54 + 0.60 - 0.40] 0.187 [4.7] A, B, C, D, E, F E2, E7 6V1 (Bulk), 6B1 (T and R) 0.200 + 0.024 - 0.016 [5.08 + 0.06 - 0.40] 0.187 [4.7] Note: • Lead space measured within 0.05 [1.27] of the body of the capacitor, or from the bottom of the crimp. Lead Style ‘A’ may be supplied with 0.59 [15] anode lead and 0.47 [12] cathode lead. Tape and Reel Packaging: Type 199D radial-leaded tantalum capacitors, all lead styles exept 1, 3 and Y are available taped and reeled per EIA-468. CASE CODE A Quantity per box bulk Quantity per box ammopack Quantity per reel www.vishay.com 116 B C 1000 2500 D 500 2000 1500 1000 For technical questions, contact: tantalum@vishay.com E F 100 1000 500 500 Document Number: 40020 Revision: 18-Mar-08 299D Vishay Sprague Solid-Electrolyte TANTALEX® Capacitors, Tripole Triple-Lead, Resin-Coated FEATURES Terminations: Tin/lead (SnPb), 100 % Tin (Sn) Pb-free • Easy Installation, economical, high performance Available RoHS* • Triple-Lead design allows reverse installations COMPLIANT • 6 Miniature Case Codes available • EIA Standard Case Sizes PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 °C to + 85 °C (to + 125 °C with voltage derating) Capacitance Tolerance: ± 20 %, ± 10 % standard ± 5 % available as special Capacitance Range: 0.10 µF to 680 µF Voltage Rating: 3 WVDC to 50 WVDC ORDERING INFORMATION 299D MODEL 227 CAPACITANCE X 003 CAPACITANCE DC VOLTAGE RATING TOLERANCE AT + 85 °C This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. X0 = ± 20 % X9 = ± 10 % *X5 = ± 5 % *special order Expressed in volts. To complete the 3-digit block, zeros precede the voltage rating. A decimal point is indicated by an “R” (6R3 = 6.3 V). A CASE CODE B LEAD STYLE 1 PACKAGING E3 ROHS COMPLIANT B = Hockey Stick 1 = Bulk See 6 = Tape and Reel Ratings 13" [330 mm] Reel and Case Codes Table E3 = 100 % tin termination (RoHS compliant) Blank = SnPb termination DIMENSIONS in inches [millimeters] W MAX. T MAX. H MAX. SEATING PLANE L TINNED SOLDERABLE LEADS S - + - 0.200 [5.08] REF. CASE A B C D E F W (MAX.) T (MAX.) 0.280 [7.1] 0 .190 [4.82] 0.280 [7.1] 0.200 [5.08] 0.280 [7.1] 0 .230 [5.84] 0.280 [7.1] 0 .270 [6.85] 0.340 [8.63] 0 .340 [8.63] 0.360 [9.14] 0 .360 [9.14] H (MAX.) L S 0.360 [9.14] 0.360 [9.14] 0.380 [9.65] 0.440 [11.17] 0.560 [14.22] 0.620 [15.74] 0.187 ± 0.032 [4.75 ± 0.82] 0.187 ± 0.032 [4.75 ± 0.82] 0.187 ± 0.032 [4.75 ± 0.82] 0.187 ± 0.032 [4.75 ± 0.82] 0.187 ± 0.032 [4.75 ± 0.82] 0.187 ± 0.032 [4.75 ± 0.82] 0.100 ± 0.015 [2.54 ± 0.38] 0.100 ± 0.015 [2.54 ± 0.38] 0.100 ± 0.015 [2.54 ± 0.38] 0.100 ± 0.015 [2.54 ± 0.38] 0.100 ± 0.015 [2.54 ± 0.38] 0.100 ± 0.015 [2.54 ± 0.38] LEAD SIZE AWG NO. NOM. DIA. 24 24 24 24 24 24 0.020 [0.51] 0.020 [0.51] 0.020 [0.51] 0.020 [0.51] 0.020 [0.51] 0.020 [0.51] * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 40044 Revision: 15-May-06 For technical questions, contact: tantalum@vishay.com www.vishay.com 117 299D Solid-Electrolyte TANTALEX® Capacitors, Tripole Triple-Lead, Resin-Coated Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 220.0 330.0 470.0 680.0 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 220.0 330.0 2.2 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 220.0 1.5 2.2 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 Max. DCL at + 25 °C (µA) 3 WVDC AT + 85 °C, SURGE = 3.6 V . . . 2 WVDC AT + 125 °C, SURGE = 2.4 V A 299D475X_003AB_ 0.5 A 299D685X_003AB_ 0.5 A 299D106X_003AB_ 0.5 A 299D156X_003AB_ 0.5 B 299D226X_003BB_ 0.6 B 299D336X_003BB_ 1.0 C 299D476X_003CB_ 1.4 D 299D686X_003DB_ 2.0 D 299D107X_003DB_ 3.0 D 299D157X_003DB_ 4.0 E 299D227X_003EB_ 5.0 E 299D337X_003EB_ 6.0 F 299D477X_003FB_ 8.0 F 299D687X_003FB_ 10.0 6.3 WVDC AT + 85 °C, SURGE = 8 V . . . 4 WVDC AT + 125 °C, SURGE = 5.0 V A 299D335X_6R3AB_ 0.5 A 299D475X_6R3AB_ 0.5 A 299D685X_6R3AB_ 0.5 B 299D106X_6R3BB_ 0.6 B 299D156X_6R3BB_ 0.9 C 299D226X_6R3CB_ 1.3 C 299D336X_6R3CB_ 2.0 D 299D476X_6R3DB_ 2.9 D 299D686X_6R3DB_ 4.0 D 299D107X_6R3DB_ 5.0 E 299D157X_6R3EB_ 6.0 F 299D227X_6R3FB_ 7.0 F 299D337X_6R3FB_ 8.0 10 WVDC AT + 85 °C, SURGE = 13 V . . . 7 WVDC AT + 125 °C, SURGE = 9.0 V A 299D225X_010AB_ 0.5 A 299D335X_010AB_ 0.5 A 299D475X_010AB_ 0.5 B 299D685X_010BB_ 0.6 B 299D106X_010BB_ 1.0 C 299D156X_010CB_ 1.5 C 299D226X_010CB_ 2.0 D 299D336X_010DB_ 3.0 D 299D476X_010DB_ 4.0 D 299D686X_010DB_ 5.0 E 299D107X_010EB_ 6.0 F 299D157X_010FB_ 7.0 F 299D227X_010FB_ 8.0 16 WVDC AT + 85 °C, SURGE = 20 V . . . 10 WVDC AT + 125 °C, SURGE = 12 V A 299D155X_016AB_ 0.5 A 299D225X_016AB_ 0.5 A 299D335X_016AB_ 0.5 B 299D475X_016BB_ 0.7 B 299D685X_016BB_ 1.0 C 299D106X_016CB_ 1.5 C 299D156X_016CB_ 2.4 D 299D226X_016DB_ 3.5 D 299D336X_016DB_ 4.0 E 299D476X_016EB_ 5.0 E 299D686X_016EB_ 6.0 F 299D107X_016FB_ 7.0 F 299D157X_016FB_ 8.0 CASE CODE PART NUMBER (1) CAP. TOL. ± 20 %, ± 10 % Max. DF at + 25 °C 120 Hz (%) 6 6 8 8 8 8 8 8 10 10 10 10 10 10 6 6 6 8 8 8 8 8 8 10 10 10 10 6 6 6 6 8 8 8 8 8 8 10 10 10 6 6 6 6 6 8 8 8 8 8 8 10 10 Note: (1) Insert capacitance tolerance code “X5”; for ± 5 % units (special order) www.vishay.com 118 For technical questions, contact: tantalum@vishay.com Document Number: 40044 Revision: 15-May-06 299D Solid-Electrolyte TANTALEX® Capacitors, Tripole Triple-Lead, Resin-Coated Vishay Sprague STANDARD RATINGS CAPACITANCE (µF) 1.0 1.5 2.2 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 1.0 1.5 2.2 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10.0 15.0 22.0 Max. DCL at + 25 °C (µA) 20 WVDC AT + 85 °C, SURGE = 26 V . . . 13 WVDC AT + 125 °C, SURGE = 16 V A 299D105X_020AB_ 0.5 A 299D155X_020AB_ 0.5 A 299D225X_020AB_ 0.5 B 299D335X_020BB_ 0.8 B 299D475X_020BB_ 1.0 C 299D685X_020CB_ 1.5 C 299D106X_020CB_ 2.0 D 299D156X_020DB_ 2.5 D 299D226X_020DB_ 3.0 E 299D336X_020EB_ 4.0 E 299D476X_020EB_ 5.0 F 299D686X_020FB_ 6.0 F 299D107X_020FB_ 7.0 25 WVDC AT + 85 °C, SURGE = 33 V . . . 17 WVDC AT + 125 °C, SURGE = 21 V A 299D105X_025AB_ 0.5 A 299D155X_025AB_ 0.5 A 299D225X_025AB_ 0.5 B 299D335X_025BB_ 0.8 B 299D475X_025BB_ 1.0 C 299D685X_025CB_ 1.5 C 299D106X_025CB_ 2.5 D 299D156X_025DB_ 3.0 D 299D226X_025DB_ 4.0 E 299D336X_025EB_ 5.0 F 299D476X_025FB_ 6.0 F 299D686X_025FB_ 7.0 35 WVDC AT + 85 °C, SURGE = 46 V . . . 23 WVDC AT + 125 °C, SURGE = 28 V A 299D104X_035AB_ 0.5 A 299D154X_035AB_ 0.5 A 299D224X_035AB_ 0.5 A 299D334X_035AB_ 0.5 A 299D474X_035AB_ 0.5 A 299D684X_035AB_ 0.5 A 299D105X_035AB_ 0.5 A 299D155X_035AB_ 0.5 B 299D225X_035BB_ 0.7 B 299D335X_035BB_ 1.0 C 299D475X_035CB_ 1.5 D 299D685X_035DB_ 2.2 D 299D106X_035DB_ 3.5 E 299D156X_035EB_ 4.0 E 299D226X_035EB_ 5.0 F 299D336X_035FB_ 6.0 F 299D476X_035FB_ 7.0 50 WVDC AT + 85 °C, SURGE = 65 V . . . 33 WVDC AT + 125 °C, SURGE = 40 V A 299D104X_050AB_ 0.5 A 299D154X_050AB_ 0.5 A 299D224X_050AB_ 0.5 A 299D334X_050AB_ 0.5 A 299D474X_050AB_ 0.5 A 299D684X_050AB_ 0.5 B 299D105X_050BB_ 0.5 C 299D155X_050CB_ 0.7 C 299D225X_050CB_ 1.1 D 299D335X_050DB_ 1.5 D 299D475X_050DB_ 2.0 F 299D685X_050FB_ 3.0 F 299D106X_050FB_ 4.0 F 299D156X_050FB_ 5.0 F 299D226X_050EB_ 6.0 CASE CODE PART NUMBER (1) CAP. TOL. ± 20 %, ± 10 % Max. DF at + 25 °C 120 Hz (%) 4 6 6 6 6 6 8 8 8 8 8 8 10 4 6 6 6 6 6 8 8 8 8 8 8 4 4 4 4 4 4 4 6 6 6 6 6 8 8 8 8 8 4 4 4 4 4 4 4 6 6 6 6 6 8 8 8 Note: (1) Insert capacitance tolerance code "X5"; for ± 5 % units (special order) Document Number: 40044 Revision: 15-May-06 For technical questions, contact: tantalum@vishay.com www.vishay.com 119 299D Solid-Electrolyte TANTALEX® Capacitors, Tripole Triple-Lead, Resin-Coated Vishay Sprague PERFORMANCE CHARACTERISTICS 1. 1.1 Operating Temperature: Capacitors are designed to operate over the temperature range of - 55 °C to + 85 °C Capacitors may be operated to + 125 °C with voltage derating to two-thirds the + 85 °C rating. + 85 °C RATING SURGE VOLTAGE (V) WORKING VOLTAGE (V) SURGE VOLTAGE (V) 3 6.3 10 16 20 25 35 50 3.6 8.0 13 20 26 33 46 65 2.0 4.0 7.0 10 13 17 23 33 2.4 5.0 9.0 12 16 21 28 40 + 85 °C + 125 °C - 10 % + 10 % + 12 % 6. Dissipation Factor: The dissipation factor, determined from the expression 2πfRC, shall not exceed values listed in the Standard Ratings Table. 6.1 Measurements shall be made by the bridge method at, or referred to, a frequency of 120 Hz and a temperature of + 25 °C. 7. Leakage Current: Capacitors shall be stabilized at the rated temperature for 30 min. Rated voltage shall be applied to capacitors for 5 minutes using a steady source of power (such as a regulated power supply) with 1000 Ω resistor connected in series with the capacitor under test to limit the charging current. Leakage current shall then be measured. + 125 °C RATING WORKING VOLTAGE (V) - 55 °C Note that the leakage current varies with temperature and applied voltage. See graph below for the appropriate adjustment factor. LEAKAGE AS A FUNCTION OF VOLTAGE AND TEMPERATURE 2. DC Working Voltage: The DC working voltage is the maximum operating voltage for continuous duty at the rated temperature. 3. Surge Voltage: The surge DC rating is the maximum voltage to which the capacitors may be subjected under any conditions, including transients and peak ripple at the highest line voltage. 1.0 Surge Voltage Test: Capacitors shall withstand the surge voltage applied in series with a 33 Ω ± 5 % resistor at the rate of o1.5 min on, 1.5 minute off, at + 85 °C, for 1000 successive test cycles. 0.3 3.2 Following the surge voltage test, the dissipation factor and the leakage current shall meet the initial requirements; the capacitance shall not have changed more than ± 5 %. 4. Capacitance Tolerance: The capacitance of all capacitors shall be within the specified tolerance limits of the nominal rating. 4.1 5. Capacitance measurements shall be made by means of polarized capacitance bridge. The polarizing voltage shall be of such magnitude that there shall be no reversal of polarity due to the AC component. The maximum voltage applied to capacitors during measurement shall be 2 Vrms at 120 Hz at + 25 °C. If the AC voltage applied is less than one-half volt rms, no DC bias is required. Measurement accuracy of the bridge shall be within ± 2 %. Capacitance Change With Temperature: The capacitance change with temperature shall not exceed the following percentage of the capacitance measured at + 25 % at: www.vishay.com 120 0.2 LEAKAGE CURRENT FACTOR 3.1 0.8 0.7 0.6 0.5 0.4 0.1 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0.008 0.007 0.006 0.005 0.004 0.003 0.002 0.001 0 10 20 30 40 50 60 70 80 90 100 PERCENT OF RATED VOLTAGE For technical questions, contact: tantalum@vishay.com Document Number: 40044 Revision: 15-May-06 299D Solid-Electrolyte TANTALEX® Capacitors, Tripole Triple-Lead, Resin-Coated PERFORMANCE CHARACTERISTICS (Continued) 7.1 At + 25 °C, the leakage current shall not exceed the value listed in the Standard Ratings Table. 7.2 At + 85 °C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings Table. 7.3 At + 125 °C, the leakage current shall not exceed 15 times the value listed in the Standard Ratings Table. 8. 8.1 I rms = where, P= RESR = 2. 9.1 Capacitors shall withstand a force of 2 pounds (9N) applied axially to the leads for 10 seconds, without failure. 9.2 Capacitor leads shall withstand 2 bends through 90° at the point of egress from the case, without failure. 9.3 No stress shall be applied to the capacitor case during the preceding tests. 10. Flammability: Encapsulant materials meet UL94 VO with an oxygen index of 32 %. 11. Capacitor Failure Mode: The predominant failure mode for solid tantalum capacitors is increased leakage current resulting in a shorted circuit. Capacitor failure may result from excess forward or reverse DC voltage, surge current, ripple current, thermal shock or excessive temperature. The increase in leakage is caused by a breakdown of the Ta2O5 dielectric. For additional information on leakage failure of solid tantalum chip capacitors, refer to Vishay Sprague Technical Paper, “Leakage Failure Mode in Solid Tantalum Chip Capacitors.” 12. Humidity Test: Capacitors shall withstand 1000 hours at + 55 °C, 90 % to 95 % relative humidity, with no voltage applied. 12.1 Following the humidity test, capacitance change shall not exceed - 10 % to + 10 % of the initial value, dissipation factor shall not exceed 150 % of the initial requirement; leakage current shall not exceed 200 % of the initial requirement. Power Dissipation in Watts at + 25 °C as given in the table in Paragraph Number 6 (Power Dissipation) The capacitor Equivalent Series Resistance at the specified frequency. A-C Ripple Voltage: The maximum allowable ripple voltage shall be determined from the formula: or, from the formula: V rms = I rms × Z Following the life test, the dissipation factor shall meet the initial requirement; the capacitance change shall not exceed - 10 % to + 10 %; the leakage current shall not exceed 125 % of the initial requirement. Lead Strength: P ---------------R ESR P V rms = Z* ---------------R ESR Life Test: Capacitors shall withstand rated DC voltage applied at + 85 °C for 1000 hours, with a circuit resistance no greater than 3 Ω. 9. Vishay Sprague where, P = Power Dissipation in Watts at + 25 °C as given in the table in Paragraph Number 6 (Power Dissipation). RESR = Z= The capacitor Equivalent Series Resistance at the specified frequency. The capacitor Impedance at the specified frequency. 2.1 The sum of the peak AC voltage plus the DC voltage shall not exceed the DC voltage rating of the capacitor. 2.2 The sum of the negative peak AC voltage plus the applied DC voltage shall not allow a voltage reversal exceeding 10 % of the DC working voltage at + 25 °C. 2.3 Temperature Derating: If these capacitors are to be operated at temperatures above + 25 °C, the permissible rms ripple current or voltage shall be calculated using the derating factors as shown: 3. TEMPERATURE DERATING FACTOR + 25 °C 1.0 + 55 °C 0.8 + 85 °C 0.6 + 125 °C 0.4 Reverse Voltage: These capacitors are capable of withstanding peak voltages in the reverse direction equal to 10 % of the DC rating at + 25 °C, 5 % of the DC rating at + 85 °C and 1 % of the DC rating at + 105 °C Guide To Application 1. A-C Ripple Current: The maximum allowable ripple current shall be determined from the formula: Document Number: 40044 Revision: 15-May-06 For technical questions, contact: tantalum@vishay.com www.vishay.com 121 299D Solid-Electrolyte TANTALEX® Capacitors, Tripole Triple-Lead, Resin-Coated Vishay Sprague 4. Recommended rated working voltage guidelines: APPLICATION VOLTAGE (V) RECOMMENDED CAPACITOR VOLTAGE RATING (V) 2.5 4.0 5. 6. 4.0 6.3 6.0 10.0 7. Power Dissipation: Power dissipation will be affected by the heat sinking capability of the mounting surface. Non-sinusoidal ripple current may produce heating effects which differ from those shown. It is important that the equivalent Irms value be established when calculating permissible operating levels. (Power Dissipation calculated using + 25 °C temperature rise). Solvent Resistance: Type 299D capacitors are conformally coated with thermosetting resin. Markings are either laser imprinted or are a heat cured black epoxy ink conforming to EIA Standard RS-327A. Marked units are compatible with Class 1 (Alcohols), Class 2 (Aromatic Hydrocarbons), Class 3 (Mineral Spirits), Class 4 (Chlorinated Hydrocarbons) and Class 5 (Fluorocarbon Methylene Chloride Azeotropes) solvents. Wave Soldering Compatibility: Capacitor leads may be subjected to immersion in molten solder at + 260 °C, to a distance of not less than 0.1" [2.54] from the capacitor body, for up to 10 seconds. The physical integrity of the capacitor shall not be impaired and the leakage current, dissipation factor and capacitance shall remain within the initial requirements after such exposure. CASE CODE MAXIMUM PERMISSIBLE POWER DISSIPATION AT + 25 °C (W) IN FREE AIR A 0.140 B 0.160 C 0.180 D 0.210 E 0.240 F 0.270 TAPE AND REEL PACKAGING in inches [millimeters] 0.020 ± 0.002 [0.508 ± 0.051] LEAD DIA. TYP. 1.270 [32.26] MAX. 0.630 ± 0.020 [16.0 ± 0.508 0.728 ± 0.020 [18.49 ± 0.508] + + 0.500 ± 0.012 [12.70 ± 0.305] + + 0.100 [2.54] TYP. 0.200 [5.08] TYP. CARRIER TAPE ADHESIVE TAPE Tape and Reel Specifications: Type 299D radial-leaded tantalum capacitors are available taped and reeled per EIA-468. Quantity of components per reel as follows: CASE CODE Requirements for non-standard configurations may be submitted to a Vishay Sales Office or representative for evaluation. www.vishay.com 122 For technical questions, contact: tantalum@vishay.com A, B, C, D E, F UNITS PER REEL 13" [330] REEL (MAX.) 1000 500 Document Number: 40044 Revision: 15-May-06 489D, 499D Vishay Sprague Resin-Coated, Radial-Lead Solid Tantalum Capacitors FEATURES • Terminations: standard SnPb, 100 % Tin available • Large capacitance range Pb-free Available • Encapsulated in a hard orange epoxy resin RoHS* • Large variety of lead styles available COMPLIANT • Supplied on tape and reel or ammopack • Low impedance and ESR at high frequencies ELECTRICAL CHARACTERISTICS Operating Temperature: - 55 °C to + 85 °C: - 55 °C to + 125 °C: Type 489D APPLICATIONS Type 499D • Offer a very cost effective solution in the consumer, industrial and professional electronics markets. The capacitors are intended for high volume applications. ORDERING INFORMATION 489D TYPE 686 CAPACITANCE 489D Standard + 85 °C 499D Standard + 125 °C Low IL X0 6R3 CAPACITANCE DC VOLTAGE RATING TOLERANCE AT + 85 °C X0 = ± 20 % Expressed in picofarads. The X9 = ± 10 % first two digits are the significant figures. The third is the number of zeros following. Expressed by zeros if needed to complete the 3 digit block. A decimal point is indicated by an “R” (6R3 = 6.3 V). D CASE CODE 2 LEAD STYLE A PACKAGING E3 RoHS COMPLIANT See Table Ratings and Case Codes 1, 2, 3, 4, 6, 9 See description on next page A = Ammopack B = Reel pack, positive leader C = Reel pack, negative leader V = Bulk Pack E3 = 100 % tin termination (RoHS compliant design) Blank = SnPb termination (standard design) LEAD STYLE CONFIGURATIONS AND DIMENSIONS (MAX) in millimeters REEL/AMMO : CODE A, B, C BULK : CODE V 1 and 3 D MAX. 2 and 4 D MAX. 9 D MAX. 6 D MAX. 2&4 6 D MAX. D MAX. H Max. H1 MAX. Upper edge of Printed Circuit Board H MAX. 0.5¯ 0.5¯ 3 15 Min. 20 Max. 0.5¯ H2 MAX. 5.5 ± 0.5 15 Min. 20 Max. H4 MAX. H3 MAX. 4.5 ± 1.5 1.1 ± 0.05 0.5¯ P ± 0.5 P P ± 0.5 P ± 0.5 P ± 0.5 LEAD STYLES 1-2-3-4 STYLE 6 STYLE 9 CASE D P H P H1 P H2 A 3.7 2.5 7.0 5 11.0 5 10.0 B 4.0 2.5 7.5 5 11.5 5 10.5 C 4.5 2.5 8.0 5 12.0 5 11.0 D 5.0 2.5 9.0 5 13.0 5 12.0 E 5.5 2.5 10.0 5 14.0 5 13.0 F 6.0 2.5 11.0 5 15.0 5 14.0 H 6.5 2.5 12.0 5 16.0 5 15.0 M 10.0 5.0 14.5 5 18.0 N 11.0 5.0 16.0 5 19.0 R 12.0 5.0 19.0 5 22.0 * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 42070 Revision: 12-Jun-06 For technical questions, contact: eurotant@vishay.com P ± 0.5 P ± 0.5 STYLES 2-4 P H3 2.5 7.0 2.5 7.5 2.5 8.0 2.5 9.0 2.5 10.0 2.5 11.0 2.5 12.0 5.0 14.5 - P 5 5 5 5 5 5 5 - STYLE 6 H4 11.0 11.5 12.0 13.0 14.0 15.0 16.0 - www.vishay.com 123 489D, 499D Resin-Coated, Radial-Lead Solid Tantalum Capacitors Vishay Sprague LEAD STYLE LEAD STYLE 1: LEAD STYLE 2: Straight leads, 2.5 mm Lead Space, Uneven Length Straight leads, 2.5 mm Lead Space, Even Length LEAD STYLE 3: LEAD STYLE 4: Straight leads, 5 mm Lead Space, Uneven Length Straight leads, 5 mm Lead Space, Even Length LEAD STYLE 6: LEAD STYLE 9: Shouldered leads, 5 mm Lead Space Snap-In leads, 5 mm Lead Space STANDARD RATINGS, CASE CODES AND LEAD STYLE CR µF RATED VOLTAGE UR AT + 85 °C 3.0 V 6.3 V 10 V 16 V 20 V LEAD STYLE 0.10 25 V 35 V A 50 V A 0.15 A A 0.22 A A 0.33 A B 0.47 A B 1-2 6-9 2-6 3-4-9 4 0.68 1.0 1.5 A 2.2 C B D B C E A B B C F A B C C D F A A B C C D H 3.3 4.7 B A 6.8 A A B C D D E N 10 B B B C D D F N 15 B B C D E E M N 22 C C C D F H M N 33 C C D E H M N 47 D D D F M M N 68 D D E M N N 100 E E M N N 150 H M M N 220 M M N R 330 N N R 470 N R 680 R R www.vishay.com 124 For technical questions, contact: eurotant@vishay.com BULK AMMO/REEL Document Number: 42070 Revision: 12-Jun-06 489D, 499D Resin-Coated, Radial-Lead Solid Tantalum Capacitors Vishay Sprague STANDARD RATINGS 499D MAX. DCL AT + 25 °C (µA) 489D MAX. DCL AT + 25 °C (µA) TYPE PART NUMBER CASE CODE CR (µF) 489D, 499D MAX. DF, 100 Hz AT + 25 °C (%) UR = 3 V AT + 85 °C, SURGE = 4 V . . . UC = 2 V AT + 125 °C, SURGE = 2.6 V (ONLY 499D) 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 220.0 330.0 470.0 680.0 A 489D685X(*)003A_ _ 1.0 0.5 B 489D106X(*)003B_ _ 1.0 0.5 B 489D156X(*)003B_ _ 1.0 0.5 C 489D226X(*)003C_ _ 1.0 0.5 C 489D336X(*)003C_ _ 1.4 0.7 D 489D476X(*)003D_ _ 2.1 1.1 D 489D686X(*)003D_ _ 3.0 1.6 E 489D107X(*)003E_ _ 4.5 2.4 H 489D157X(*)003H_ _ 6.7 3.6 M 489D227X(*)003M_ _ 9.9 5.2 N 489D337X(*)003N_ _ 14.8 7.9 N 489D477X(*)003N_ _ 21.1 11.2 R 489D687X(*)003R_ _ 30.6 16.3 UR = 6.3 V AT + 85 °C, SURGE = 8 V . . . UC = 4 V AT + 125 °C, SURGE = 5.2 V (ONLY 499D) 6 8 8 8 8 8 8 10 10 10 10 12 12 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 220.0 330.0 470.0 680.0 A 489D475X(*)6R3A_ _ 1.0 0.5 A 489D685X(*)6R3A_ _ 1.0 0.5 B 489D106X(*)6R3B_ _ 1.0 0.5 B 489D156X(*)6R3B_ _ 1.4 0.7 C 489D226X(*)6R3C_ _ 2.0 1.1 C 489D336X(*)6R3C_ _ 3.1 1.6 D 489D476X(*)6R3D_ _ 4.4 2.3 D 489D686X(*)6R3D_ _ 6.4 3.4 E 489D107X(*)6R3E_ _ 9.4 5.0 M 489D157X(*)6R3M_ _ 14.1 7.5 M 489D227X(*)6R3M_ _ 20.7 11.0 N 489D337X(*)6R3N_ _ 31.1 16.6 R 489D477X(*)6R3R_ _ 44.4 23.6 R 489D687X(*)6R3R_ _ 64.2 34.2 UR = 10 V AT + 85 °C, SURGE = 13 V . . . UC = 7 V AT + 125 °C, SURGE = 8.6 V (ONLY 499D) 6 6 8 8 8 8 8 8 10 10 10 10 12 12 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 220.0 330.0 A A B B C C D D E M M N R 489D335X(*)010A_ _ 489D475X(*)010A_ _ 489D685X(*)010B_ _ 489D106X(*)010B_ _ 489D156X(*)010C_ _ 489D226X(*)010C_ _ 489D336X(*)010D_ _ 489D476X(*)010D_ _ 489D686X(*)010E_ _ 489D107X(*)010M_ _ 489D157X(*)010M_ _ 489D227X(*)010N_ _ 489D337X(*)010R_ _ 1.0 1.0 1.0 1.5 2.2 3.3 4.9 7.0 10.2 15.0 22.5 33.0 49.5 0.5 0.5 0.5 0.8 1.2 1.7 2.6 3.7 5.4 8.0 12.0 17.6 26.4 6 6 6 8 8 8 8 8 8 10 10 10 10 Note: 489D Type part number 489D, 499D (*) Insert 0 for ± 20 % tolerance or 9 for ± 10 % _ _ Case code/lead style see case code table PACKAGING QUANTITIES CASE CODE A B C D E F H M 500 BULK R 100 AMMOPACK 2500 2000 1500 500 REEL PACK 2500 2000 1500 500 Document Number: 42070 Revision: 12-Jun-06 N For technical questions, contact: eurotant@vishay.com www.vishay.com 125 489D, 499D Resin-Coated, Radial-Lead Solid Tantalum Capacitors Vishay Sprague STANDARD RATINGS CR (µF) TYPE PART NUMBER CASE CODE 489D MAX. DCL AT + 25 °C (µA) 489D, 499D MAX. DF, 100 Hz AT + 25 °C (%) 499D MAX. DCL AT + 25 °C (µA) UR = 16 V AT + 85 °C, SURGE = 20 V . . . UC = 10 V AT + 125 °C, SURGE = 13 V (ONLY 499D) 2.2 A 489D225X(*)016A_ _ 1.0 0.5 6 3.3 B 489D335X(*)016B_ _ 1.0 0.5 6 4.7 B 489D475X(*)016B_ _ 1.1 0.6 6 6.8 C 489D685X(*)016C_ _ 1.6 0.8 6 10.0 C 489D106X(*)016C_ _ 2.4 1.2 8 15.0 D 489D156X(*)016D_ _ 3.6 1.9 8 22.0 D 489D226X(*)016D_ _ 5.2 2.8 8 33.0 E 489D336X(*)016E_ _ 7.9 4.2 8 47.0 F 489D476X(*)016F_ _ 11.2 6.0 8 68.0 M 489D686X(*)016M_ _ 16.3 8.7 8 100.0 N 489D107X(*)016N_ _ 24.0 12.8 10 150.0 N 489D157X(*)016N_ _ 36.0 19.2 10 220.0 R 489D227X(*)016R_ _ 52.8 28.1 10 UR = 20 V AT + 85 °C, SURGE = 26 V . . . UC = 13 V AT + 125 °C, SURGE = 16 V (ONLY 499D) 1.5 A 489D155X(*)020A_ _ 1.0 0.5 4 2.2 B 489D225X(*)020B_ _ 1.0 0.5 6 3.3 C 489D335X(*)020C_ _ 1.0 0.5 6 4.7 C 489D475X(*)020C_ _ 1.4 0.7 6 6.8 D 489D685X(*)020D_ _ 2.0 1.0 6 10.0 D 489D106X(*)020D_ _ 3.0 1.6 8 15.0 E 489D156X(*)020E_ _ 4.5 2.4 8 22.0 F 489D226X(*)020F_ _ 6.6 3.5 8 33.0 H 489D336X(*)020H_ _ 9.9 5.2 8 47.0 M 489D476X(*)020M_ _ 14.1 7.5 8 68.0 N 489D686X(*)020N_ _ 20.4 10.8 8 100.0 N 489D107X(*)020N_ _ 30.0 16.0 10 UR = 25 V AT + 85 °C, SURGE = 32 V . . . UC = 17 V AT + 125 °C, SURGE = 21 V (ONLY 499D) 1.0 A 489D105X(*)025A_ _ 1.0 0.5 4 1.5 B 489D155X(*)025B_ _ 1.0 0.5 4 2.2 B 489D225X(*)025B_ _ 1.0 0.5 6 3.3 C 489D335X(*)025C_ _ 1.2 0.6 6 4.7 C 489D475X(*)025C_ _ 1.7 0.9 6 6.8 D 489D685X(*)025D_ _ 2.5 1.3 6 10.0 D 489D106X(*)025D_ _ 3.7 2.0 8 15.0 E 489D156X(*)025E_ _ 5.6 3.0 8 22.0 H 489D226X(*)025H_ _ 8.2 4.4 8 33.0 M 489D336X(*)025M_ _ 12.3 6.6 8 47.0 M 489D476X(*)025M_ _ 17.6 9.4 8 68.0 N 489D686X(*)025N_ _ 25.5 13.6 8 Note: 489D Type part number 489D, 499D (*) Insert 0 for ± 20 % tolerance or 9 for ± 10 % _ _ Case code/lead style see case code table www.vishay.com 126 For technical questions, contact: eurotant@vishay.com Document Number: 42070 Revision: 12-Jun-06 489D, 499D Resin-Coated, Radial-Lead Solid Tantalum Capacitors Vishay Sprague STANDARD RATINGS CR (µF) TYPE PART NUMBER CASE CODE 489D MAX. DCL AT + 25 °C (µA) 499D MAX. DCL AT + 25 °C (µA) 489D, 499D MAX. DF, 100 Hz AT + 25 °C (%) UR = 35 V AT + 85 °C, SURGE = 46 V . . . UC= 23 V AT + 125 °C, SURGE = 28 V (ONLY 499D) 0.10 A 489D104X(*)035A_ _ 1.0 0.5 4 0.15 A 489D154X(*)035A_ _ 1.0 0.5 4 0.22 A 489D224X(*)035A_ _ 1.0 0.5 4 0.33 A 489D334X(*)035A_ _ 1.0 0.5 4 0.47 A 489D474X(*)035A_ _ 1.0 0.5 4 0.68 B 489D684X(*)035B_ _ 1.0 0.5 4 1.0 B 489D105X(*)035B_ _ 1.0 0.5 4 1.5 C 489D155X(*)035C_ _ 1.0 0.5 4 2.2 C 489D225X(*)035C_ _ 1.1 0.6 6 3.3 D 489D335X(*)035D_ _ 1.7 0.9 6 4.7 D 489D475X(*)035D_ _ 2.4 1.3 6 6.8 E 489D685X(*)035E_ _ 3.5 1.9 6 10.0 F 489D106X(*)035F_ _ 5.2 2.8 8 15.0 M 489D156X(*)035M_ _ 7.8 4.2 8 22.0 M 489D226X(*)035M_ _ 11.5 6.1 8 33.0 N 489D336X(*)035N_ _ 17.3 9.2 8 N 489D476X(*)035N_ _ 24.6 13.1 8 47.0 UR = 50 V AT + 85 °C, SURGE = 65 V . . . UC = 33 V AT + 125 °C, SURGE = 40 V (ONLY 499D) 0.10 A 489D104X(*)050A_ _ 1.0 0.5 4 0.15 A 489D154X(*)050A_ _ 1.0 0.5 4 0.22 A 489D224X(*)050A_ _ 1.0 0.5 4 0.33 B 489D334X(*)050B_ _ 1.0 0.5 4 0.47 B 489D474X(*)050B_ _ 1.0 0.5 4 0.68 C 489D684X(*)050C_ _ 1.0 0.5 4 1.0 D 489D105X(*)050D_ _ 1.0 0.5 4 1.5 E 489D155X(*)050E_ _ 1.1 0.6 4 2.2 F 489D225X(*)050F_ _ 1.6 0.8 6 3.3 F 489D335X(*)050F_ _ 2.4 1.3 6 4.7 H 489D475X(*)050H_ _ 3.5 1.8 6 6.8 N 489D685X(*)050N_ _ 5.1 2.7 6 10.0 N 489D106X(*)050N_ _ 7.5 4.0 8 15.0 N 489D156X(*)050N_ _ 11.2 6.0 8 22.0 N 489D226X(*)050N_ _ 16.5 8.8 8 Note: 489D Type part number 489D, 499D (*) Insert 0 for ± 20 % tolerance or 9 for ± 10 % _ _ Case code/lead style see case code table Document Number: 42070 Revision: 12-Jun-06 For technical questions, contact: eurotant@vishay.com www.vishay.com 127 489D, 499D Resin-Coated, Radial-Lead Solid Tantalum Capacitors Vishay Sprague PERFORMANCE CHARACTERISTICS 6. 1. Operating Temperature: - 55 °C to + 85 °C with rated DC voltage UR applied. + 85 °C to + 125° C with linear voltage derating to category voltage UC for 499D only (see general information) 2. Capacitance and Tolerance: Capacitance measured at 100 Hz and + 25 °C shall be within the specified tolerance limits of the nominal rating. Capacitance measurement shall be made by means of a polarized capacitance bridge. No polarizing voltage is required. The maximum voltage applied during measurements shall be 0.5 Vrms at 100 Hz and + 25 °C. 3. 4. Capacitance change Within ± 10 % of initial value DC leakage current Within initial requirements at + 25 °C Dissipation factor Within initial requirements at + 25 °C 7. Reverse Voltage: These capacitors are capable of withstanding peak voltage in the reverse direction equal to: 15 % of the rated DC voltage at + 20 °C 10 % of the rated DC voltage at + 25 °C 5 % of the rated DC voltage at + 85 °C Life Test: After 2000 hours at + 85 °C with rated DC voltage applied, or after 1000 hours at + 125 °C. With derated DC voltage*, capacitors shall meet the requirements in table below. (*only for 499D) Humidity Test: After 21 days (504 hours) (1) at + 40 °C, 90 to 95 % of relative humidity (per IEC 68-2-3) with no voltage applied, capacitors shall meet the requirements in table below. Capacitance change Within ± 5 % of initial value DC leakage current Within initial requirements at + 25 °C - Table 2 Dissipation factor Within initial requirements at + 25 °C - Table 2 Note: (1) Humidity test is 56 days (1350 hours) for 499D Surge Voltage: DC rated voltage at + 85 °C (V) 3 6.3 10 16 20 25 35 50 DC surge voltage at + 85 °C (V) 4 DC rated voltage at + 125 °C (V) (1) 2 DC surge voltage at + 125 °C (V) (1) 8. 8 13 20 26 32 46 65 4 7 10 13 17 23 33 2.6 5.2 8.6 13 16 21 28 40 Note: (1) for 499D Marking: The capacitors shall be marked with the rated capacitance and the rated DC working voltage. A code may be used for both capacitance and voltage. Units rated at 6.3 volts are usually marked as 6 volts. The package shall be marked with full Vishay Sprague part number, date code and quantity. Capacitors shall withstand the surge voltage applied in series with a 1000 Ω (± 5 %) resistor, at the rate of 1.5 minute on, 5.5 minute off for 1000 successive test cycles at + 85 °C. After test, capacitance change shall not exceed 10 % of initial value, dissipation factor and DC leakage current shall meet initial requirements at + 25 °C - Table 2. 5. Stability at low and high temperatures: 489D - Table 2A TEMP. CAPACITANCE CHANGE DC LEAKAGE CURRENT (1) - 55 °C - 10 % of initial value ----------- + 25 °C ------------- 0.015 CR x UR or 1 µA, whichever is greater + 85 °C + 10 % of initial value 0.15 CR x UR or 10 µA, whichever is greater TEMP. CAPACITANCE CHANGE DC LEAKAGE CURRENT (1) - 55 °C - 10 % of initial value ------------- ------------ 0.008 CR x UR or 0.5 µA, whichever is greater + 85 °C + 10 % of initial value 0.08 CR x UR or 5 µA, whichever is greater + 125 °C (2) + 10 % of initial value 0.1 CR x UR or 6.25 µA, whichever is greater + 25 °C DISSIPATION FACTOR AT 100 Hz CR ≤ 1.5 µF 1.5 µF < CR < 10 µF 10 µF < CR < 100 µF 100 µF ≤ CR ≤ 330 µF 330 µF < CR 4 % max 6 % max 8 % max 10 % max 12 % max DISSIPATION FACTOR AT 100 Hz CR ≤ 1.5 µF 4 % max 1.5 µF < CR < 10 µF 10 µF < CR < 100 µF 100 µF ≤ CR ≤ 330 µF 6 % max 8 % max 10 % max 330 µF < CR 12 % max Notes: (1) Rated voltage applied for 5 minutes with a series resistor of 1000 Ω (2) Only for 499 D www.vishay.com 128 For technical questions, contact: eurotant@vishay.com Document Number: 42070 Revision: 12-Jun-06 489D, 499D Resin-Coated, Radial-Lead Solid Tantalum Capacitors Vishay Sprague GUIDE TO APPLICATION 1. A-C Ripple Current: The maximum allowable ripple current shall be determined from the formula: I rms = where, P= RESR = 2. P ---------------R ESR Power Dissipation in Watts at + 25 °C as given below The capacitor Equivalent Series Resistance at the specified frequency. A-C Ripple Voltage: The maximum allowable ripple voltage shall be determined from the formula: P ----------------- × Z R ESR V rms = where, Z= 3. 4. The capacitor Impedance at the specified frequency. Power dissipation: Power dissipation will be affected by the heat sinking capability of the mounting surface. Non-sinusoidal ripple current may produce heating effects which differ from those shown in the following table. It is important that the equivalent IRMS value be established when calculating permissible operating levels. CASE CODE POWER DISSIPATION AT + 25 °C (W) A 0.080 B 0.090 C 0.100 D 0.110 E 0.120 F 0.130 AC ripple current or voltage derating factor: If these capacitors are to be operated at temperatures above + 25 °C, the permissible rms ripple current or voltage shall be calculated using the derating factors in the table below: H 0.140 M 0.150 TEMPERATURE DERATING FACTOR N 0.160 + 25 °C 1.0 R 0.180 + 55 °C 0.9 + 85 °C 0.8 + 125 °C 0.4 Document Number: 42070 Revision: 12-Jun-06 5. Cleaning: These capacitors are compatible with all commonly used solvents, such as TES, TMS, Prelete and Chloretane. Solvents containing methylene chloride or other epoxy solvents should be avoided since these will attack the epoxy encapsulation material. For technical questions, contact: eurotant@vishay.com www.vishay.com 129 489D, 499D Resin-Coated, Radial-Lead Solid Tantalum Capacitors Vishay Sprague TAPE AND REEL PACKAGING in millimeters (meets IEC 286-2) P2 P2 P Δh ΔP P H2 P1 F P1 H W2 F H0 L W0 W1 W t P0 UNREELING DIRECTION D0 Dimensions for components on tape and tolerances: DESIGNATION SYMBOL DIMENSIONS (mm) Pitch of component P 12.7 ± 1.0 Feed hole pitch P0 12.7 ± 0.3 Tape width W 18 (+ 1/- 0.5) Hold down tape width W0 5.0 Hole position W1 9 (+ 0.75/- 0.5) Hold down tape position W2 0 (+ 3/- 0) Overall component height H1 32 max. Component alignment ΔP ± 1.3 max. Feed hole diameter D0 4.0 ± 0.3 t 0.5 ± 0.2 ΔH 0±2 Tape thickness Component alignment Lengh of snipped leads L 11 max. Lead clinch height H0 16.0 ± 0.5 Lead wire spacing F 2.5 Feed hole center to wire center P1 5.1 ± 0.7 Hole center to component center P2 6.35 ± 1.3 Component height H www.vishay.com 130 + 0.6 - 0.1 For technical questions, contact: eurotant@vishay.com 5 + 0.6 - 0.1 3.65 ± 0.7 6.35 ± 1.3 18 ± 1 Document Number: 42070 Revision: 12-Jun-06 ETPW Vishay Sprague Resin-Coated, Radial-Leaded Solid Tantalum Capacitors FEATURES • RoHS Compliant design available • Flame retardant encapsulation Pb-free Available • Very high temperature range RoHS* • Improved humidity class COMPLIANT • Low leakage current • Very high CV product • Low failure rate MECHANICAL SPECIFICATIONS Color: Gold Tantalum capacitors with sintered anode and solid semiconductor electrolyte with flame retardant fluidized bed coating. The type ETPW is characterized by very favorable electrical values even at higher ambient temperatures. The capacitors comply with DIN 45910 part 146 and they are also available as a radially taped version. Laser Marked: Capacity and voltage in clear text; Plus pole marked Leads: Standard (Tin/Lead), RoHS compliant (100 % Tin) ORDERING INFORMATION P1A TYPE ETPW 1A .... ETPW 6R 686 CAPACITANCE 603 DC VOLTAGE RATING AT + 85 °C M CAPACITANCE TOLERANCE 00 LEAD STYLE AND PACKAGING Expressed in picofarads. The first two digits are significant figures. The third is the number of zeros following. Expressed by zeros if needed to complete the 3 digit block. A decimal point is indicated by an “0“ (603 = 6.3 Volts) M = ± 20 % K = ± 10 % See Lead styles and packaging table D E3 RoHS COMPLIANT E3 = 100 % tin termination (RoHS compliant design) Blank = SnPb termination (standard design) DIMENSIONS in millimeters BASIC VERSION FORM DS FORM L D D D 1.1 ± 0.1 H2 5.5 ± 0.5 Ød 4.5 ± 1.5 15 ± 0.5 H2 H D RM ± 0.5 RM ± 0.5 RM ± 0.5 MODEL ETPW - 1 A,B ETPW - 2 C,D ETPW - 2 E ETPW - 3 F ETPW - 3 G ETPW - 4 H ETPW - 5 J,K (1) ETPW - 5 J,K,L ETPW - 6 M,N ETPW - 6 P,R D MAX. H MAX. 4.0 4.5 5.0 5.0 5.5 6.0 8.6 8.6 9.5 9.5 7.1 8.0 9.5 9.5 10.0 10.0 12.5 12.5 15.0 16.0 RM ± 0.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 5.0 5.0 5.0 Ø D ± 0.05 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 FORM DS H2 MAX. RM 10.5 5 11.0 5 12.5 5 12.5 5 13.0 5 13.0 5 15.5 5 15.5 5 18.0 5 19.0 5 FORM L H2 MAX. 10.5 11.0 12.5 12.5 13.0 13.0 15.5 - RM 5 5 5 5 5 5 5 - Note: (1) J,K with RM 2.5 mm : 100 µF - 6.3 V, 68 µF - 10 V, 47 µF - 16 V, 22 µF - 25 V * Pb containing terminations are not RoHS compliant, exemptions may apply Document Number: 42074 Revision: 12-Jun-06 For technical questions, contact: eurotant@vishay.com www.vishay.com 131 ETPW Resin-Coated, Radial-Leaded Solid Tantalum Capacitors Vishay Sprague STANDARD RATINGS AND CASE CODES RATED VOLTAGE UR at + 85 °C CR µF 3.0 V 6.3 V 10 V 16 V 25 V 35 V 50 V 0.10 1A 1A 0.15 1A 1A 0.22 1A 1A 0.33 1A 1B 0.47 1A 1B 0.68 1A 2C 1.0 1A 1A 2D 1.5 1A 1B 2E 1B 2C 3F 2.2 1A 3.3 4.7 1A 1B 2C 2D 3G 1A 1B 2C 2D 2E 4H 6.8 1A 1B 2C 2D 2E 3F 5J 10 1A 2C 2D 2E 3F 3G 5L 15 1B 2D 2E 3F 4H 5J 6M 22 2C 2E 3F 3G 5J 5L 6P 33 2D 3F 3G 4H 5K 6M 47 2E 3G 4H 5K 6M 6P 6N 68 3F 4H 5J 5L 100 3G 5J 5L 6N 150 4H 5L 6N 6R 220 5J 6M 6P 330 5L 6P 470 STANDARD RATINGS DIMENSIONS MAX. DCL MAX. Z AT AT 100 kHz + 20 °C, (Ω) (µA) MAX. DF AT 120 Hz + 20 °C CR (µF) CASE CODE 6.8 1A UR = 3 V AT + 85 °C, Surge = 3.9 V . . . UC = 2 V AT + 125 °C P1A685003(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 6.0 0.06 10.0 1A P1A106003(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 5.0 0.08 15.0 1B P1B156003(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 4.0 0.08 22.0 2C P2C226003(*)_ _D 4.5 8.0 11.0 2.5 0.5 0.7 3.2 0.08 33.0 2D P2D336003(*)_ _D 4.5 8.0 11.0 2.5 0.5 1.0 2.5 0.08 47.0 2E P2E476003(*)_ _D 5.0 9.5 12.5 2.5 0.5 1.4 2.0 0.08 68.0 3F P3F686003(*)_ _D 5.0 9.5 12.5 2.5 0.5 2.0 1.6 0.08 100.0 3G P3G107003(*)_ _D 5.5 10.0 13.0 2.5 0.5 3.0 1.2 0.10 150.0 4H P4H157003(*)_ _D 6.0 10.0 13.0 2.5 0.5 4.5 1.0 0.10 220.0 5J P5J227003(*)_ _D 8.6 12.5 15.5 5.0 0.5 6.6 0.8 0.10 330.0 5L P5L337003(*)_ _D 8.6 12.5 15.5 5.0 0.5 9.9 0.6 0.10 PART NUMBER D MAX. (mm) H MAX. (mm) H2 MAX. (mm) RM ± 0.05 d ± 0.05 Note: (*) Insert M for ± 20 % tolerance or K for ± 10 % _ _ Lead style and packaging code, see lead style and packaging www.vishay.com 132 For technical questions, contact: eurotant@vishay.com Document Number: 42074 Revision: 12-Jun-06 ETPW Resin-Coated, Radial-Leaded Solid Tantalum Capacitors Vishay Sprague STANDARD RATINGS CR (µF) CASE CODE 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 220.0 330.0 1A 1B 2C 2D 2E 3F 3G 4H 5J 5L 6M 6P 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 220.0 1A 1B 2C 2D 2E 3F 3G 4H 5J 5L 6N 6P 2.2 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 1A 1B 2C 2D 2E 3F 3G 4H 5K 5L 6N 6R DIMENSIONS PART NUMBER D MAX. H MAX. H2 MAX. RM d (mm) (mm) ± 0.05 ± 0.05 (mm) UR = 6.3 V AT + 85 °C, Surge = 7.8 V . . . UC = 4 V AT + 125 °C P1A475603(*)_ _D 4.0 7.1 10.5 2.5 0.5 P1B685603(*)_ _D 4.0 7.1 10.5 2.5 0.5 P2C106603(*)_ _D 4.5 8.0 11.0 2.5 0.5 P2D156603(*)_ _D 4.5 8.0 11.0 2.5 0.5 P2E226603(*)_ _D 5.0 9.5 12.5 2.5 0.5 P3F336603(*)_ _D 5.0 9.5 12.5 2.5 0.5 P3G476603(*)_ _D 5.5 10.0 13.0 2.5 0.5 P4H686603(*)_ _D 6.0 10.0 13.0 2.5 0.5 P5J107603(*)_ _D 8.6 12.5 15.5 2.5 0.5 P5L157603(*)_ _D 8.6 12.5 15.5 5.0 0.5 P6M227603(*)_ _D 9.5 15.0 18.0 5.0 0.5 P6P337603(*)_ _D 9.5 16.0 19.0 5.0 0.5 UR = 10 V AT + 85 °C, Surge = 13 V . . . UC = 6.3 V AT + 125 °C P1A335010(*)_ _D 4.0 7.1 10.5 2.5 0.5 P1B475010(*)_ _D 4.0 7.1 10.5 2.5 0.5 P2C685010(*)_ _D 4.5 8.0 11.0 2.5 0.5 P2D106010(*)_ _D 4.5 8.0 11.0 2.5 0.5 P2E156010(*)_ _D 5.0 9.5 12.5 2.5 0.5 P3F226010(*)_ _D 5.0 9.5 12.5 2.5 0.5 P3G336010(*)_ _D 5.5 10.0 13.0 2.5 0.5 P4H476010(*)_ _D 6.0 10.0 13.0 2.5 0.5 P5J686010(*)_ _D 8.6 12.5 15.5 2.5 0.5 P5L107010(*)_ _D 8.6 12.5 15.5 5.0 0.5 P6N157010(*)_ _D 9.5 15.0 18.0 5.0 0.5 P6P227010(*)_ _D 9.5 16.0 19.0 5.0 0.5 UR = 16 V AT + 85 °C, Surge = 20.8 V . . . UC = 10 V AT + 125 °C P1A225016(*)_ _D 4.0 7.1 10.5 2.5 0.5 P1B335016(*)_ _D 4.0 7.1 10.5 2.5 0.5 P2C475016(*)_ _D 4.5 8.0 11.0 2.5 0.5 P2D685016(*)_ _D 4.5 8.0 11.0 2.5 0.5 P2E106016(*)_ _D 5.0 9.5 12.5 2.5 0.5 P3F156016(*)_ _D 5.0 9.5 12.5 2.5 0.5 P3G226016(*)_ _D 5.5 10.0 13.0 2.5 0.5 P4H336016(*)_ _D 6.0 10.0 13.0 2.5 0.5 P5K476016(*)_ _D 8.6 12.5 15.5 2.5 0.5 P5L686016(*)_ _D 8.6 12.5 15.5 5.0 0.5 P6N107016(*)_ _D 9.5 15.0 18.0 5.0 0.5 P6R157016(*)_ _D 9.5 16.0 19.0 5.0 0.5 UR = 25 V AT + 85 °C, Surge = 32.5 V . . . UC = 16 V AT + 125 °C P1A105025(*)_ _D 4.0 7.1 10.5 2.5 0.5 P1A155025(*)_ _D 4.0 7.1 10.5 2.5 0.5 P1B225025(*)_ _D 4.0 7.1 10.5 2.5 0.5 P2C335025(*)_ _D 4.5 8.0 11.0 2.5 0.5 P2D475025(*)_ _D 4.5 8.0 11.0 2.5 0.5 P2E685025(*)_ _D 5.0 9.5 12.5 2.5 0.5 P3F106025(*)_ _D 5.0 9.5 12.5 2.5 0.5 P4H156025(*)_ _D 6.0 10.0 13.0 2.5 0.5 P5J226025(*)_ _D 8.6 12.5 15.5 2.5 0.5 P5K336025(*)_ _D 8.6 12.5 15.5 5.0 0.5 P6M476025(*)_ _D 9.5 15.0 18.0 5.0 0.5 P6N686025(*)_ _D 9.5 15.0 18.0 5.0 0.5 1.0 1A 1.5 1A 2.2 1B 3.3 2C 4.7 2D 6.8 2E 10.0 3F 15.0 4H 22.0 5J 33.0 5K 47.0 6M 68.0 6N Note: (*) Insert M for ± 20 % tolerance or K for ± 10 % _ _ Lead style and packaging code, see lead style and packaging Document Number: 42074 Revision: 12-Jun-06 For technical questions, contact: eurotant@vishay.com MAX. DCL MAX. Z AT AT 100 kHz + 20 °C, (Ω) (µA) MAX. DF AT 120 Hz + 20 °C 0.5 0.5 0.6 0.9 1.4 2.1 3.0 4.3 6.3 9.5 13.9 20.8 6.0 5.0 4.0 3.2 2.5 2.0 1.6 1.2 1.0 0.8 0.6 0.5 0.06 0.06 0.08 0.08 0.08 0.08 0.08 0.08 0.10 0.10 0.10 0.10 0.5 0.5 0.7 1.0 1.5 2.2 3.3 4.7 6.8 10.0 15.0 22.0 6.5 5.0 4.0 3.2 2.5 2.0 1.6 1.2 1.0 0.8 0.6 0.5 0.06 0.06 0.06 0.08 0.08 0.08 0.08 0.08 0.08 0.10 0.10 0.10 0.5 0.5 0.8 1.1 1.6 2.4 3.5 5.3 7.5 10.9 16.0 24.0 7.0 6.0 4.5 3.2 2.5 2.0 1.6 1.2 1.0 0.8 0.6 0.5 0.06 0.06 0.06 0.06 0.08 0.08 0.08 0.08 0.08 0.08 0.10 0.10 0.5 0.5 0.6 0.8 1.2 1.7 2.5 3.8 5.5 8.3 11.8 17.0 8.5 7.5 6.0 4.5 3.2 2.5 2.0 1.6 1.2 1.0 0.8 0.6 0.04 0.04 0.06 0.06 0.06 0.06 0.08 0.08 0.08 0.08 0.08 0.08 www.vishay.com 133 ETPW Resin-Coated, Radial-Leaded Solid Tantalum Capacitors Vishay Sprague STANDARD RATINGS DIMENSIONS MAX. DCL MAX. Z AT AT 100 kHz + 20 °C, (OHMS) (µA) MAX. DF AT 120 Hz + 20 °C CR (µF) CASE CODE PART NUMBER 0.1 1A P1A104035(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 38.0 0.04 0.15 1A P1A154035(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 30.0 0.04 0.22 1A P1A224035(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 23.0 0.04 0.33 1A P1A334035(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 18.0 0.04 0.47 1A P1A474035(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 14.0 0.04 0.68 1A P1A684035(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 10.0 0.04 1.0 1A P1A105035(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 8.0 0.04 D MAX. (mm) H MAX. (mm) H2 MAX. (mm) RM ± 0.05 d ± 0.05 UR = 35 V AT + 85 °C, Surge = 45.5 V . . . UC = 23 V AT + 125 °C 1.5 1B P1B155035(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 6.5 0.04 2.2 2C P2C225035(*)_ _D 4.5 8.0 11.0 2.5 0.5 0.8 5.0 0.06 3.3 2D P2D335035(*)_ _D 4.5 8.0 11.0 2.5 0.5 1.2 3.5 0.06 4.7 2E P2E475035(*)_ _D 5.0 9.5 12.5 2.5 0.5 1.6 2.5 0.06 6.8 3F P3F685035(*)_ _D 5.0 9.5 12.5 2.5 0.5 2.4 2.0 0.06 10.0 3G P3G106035(*)_ _D 5.5 10.0 13.0 2.5 0.5 3.5 1.6 0.08 15.0 5J P5J156035(*)_ _D 8.6 12.5 15.5 5.0 0.5 5.3 1.2 0.08 22.0 5L P5L226035(*)_ _D 8.6 12.5 15.5 5.0 0.5 7.7 1.0 0.08 33.0 6M P6M336035(*)_ _D 9.5 15.0 18.0 5.0 0.5 11.6 0.8 0.08 47.0 6P P6P476035(*)_ _D 9.5 16.0 19.0 5.0 0.5 16.5 0.8 0.08 UR = 50 V AT + 85 °C, Surge = 65 V . . . UC = 33 V AT + 125 °C 0.1 1A P1A104050(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 38.0 0.04 0.15 1A P1A154050(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 30.0 0.04 0.22 1A P1A224050(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 23.0 0.04 0.33 1B P1B334050(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 18.0 0.04 0.47 1B P1B474050(*)_ _D 4.0 7.1 10.5 2.5 0.5 0.5 14.0 0.04 0.68 2C P2C684050(*)_ _D 4.5 8.0 11.0 2.5 0.5 0.5 10.0 0.04 1.0 2D P2D105050(*)_ _D 4.5 8.0 11.0 2.5 0.5 0.5 8.0 0.04 1.5 2E P2E155050(*)_ _D 5.0 9.5 12.5 2.5 0.5 0.8 6.5 0.04 2.2 3F P3F225050(*)_ _D 5.0 9.5 12.5 2.5 0.5 1.1 5.0 0.06 3.3 3G P3G335050(*)_ _D 5.5 10.0 13.0 2.5 0.5 1.7 3.5 0.06 4.7 4H P4H475050(*)_ _D 6.0 10.0 13.0 2.5 0.5 2.4 2.5 0.06 6.8 5J P5J685050(*)_ _D 8.6 12.5 15.5 5.0 0.5 3.4 2.0 0.06 10.0 5L P5L106050(*)_ _D 8.6 12.5 15.5 5.0 0.5 5.0 1.6 0.08 15.0 6M P6M156050(*)_ _D 9.5 15.0 18.0 5.0 0.5 7.5 1.2 0.08 22.0 6P P6P226050(*)_ _D 9.5 16.0 19.0 5.0 0.5 11.0 1.0 0.08 Note: (*) Insert M for ± 20 % tolerance or K for ± 10 % _ _ Lead style and packaging code, see lead style and packaging www.vishay.com 134 For technical questions, contact: eurotant@vishay.com Document Number: 42074 Revision: 12-Jun-06 ETPW Resin-Coated, Radial-Leaded Solid Tantalum Capacitors Vishay Sprague PERFORMANCE CHARACTERISTICS 1. Climatic Category: 55/125/56 acc. to IEC 2. Temperature Range: - 55 °C up to + 125 °C with linear voltage derating to category voltage UC 3. Rated Voltage, Category Voltage: 3 V to 50 V; 2 V to 33 V 4. The values apply for + 20 °C For higher temperatures, the values have to be multiplied with the following factors: TEMPERATURE FACTOR + 50 °C 0.7 + 85 °C 0.5 + 125 °C 0.3 Surge Voltage: 1.3 times of rated voltage at + 85 °C 5. Reverse Voltage (Temporary): 15 % of the rated DC voltage at + 20 °C 10 % of the rated DC voltage at + 55 °C 5 % of the rated DC voltage at + 85 °C 6. Rated Capacitance: 0.1 µF to 330 µF 7. Capacitance Tolerance: ± 20 %, ± 10 %, 8. Leakage Current in µA: Measured at + 20 °C after 5 minutes: ≤ 0.01 x CR x UR or 0.5 µA, whichever is greater 9. Intermediate values can be obtained by linear interpolation. For further notes on AC voltage stress: See general information 12. Service life: > 300 000 h (2) 13. Failure percentage: ≤ 0.6 % within 100 000 h (2) 14. Failure rate (λ): ≤ 0.6 10- 7/h = ≤ 60 fit (2) 15. Failure criteria: Catastrophic failure: Short circuit or interruption Dissipation Factor: at 120 Hz and + 20 °C See table Drift failure: DC/C > + 5 - 15 % Z > 3 times initial limit value IR > 5 times initial value + 5 µA 10. Impedance: Measured at 100 kHz and + 20 °C See table 11. Permissible AC Voltage Stress: The highest permissible AC voltage for the respective frequency may be taken from the brochure “General information”. 16. Characteristics at high and low temperatures (the values shall not exceed the following limits) Note: (2) related to UR, + 40 °C and a circuit resistance of ≥ 3 W/V TEST TEMPERATURE - 55 °C + 20 °C + 85 °C + 125 °C ΔC/C < tanδ ≤ 1.5 µF < 10 µF < 100 µF ≥ 100 µF - 10 % - + 12 % + 15 % 0.04 0.06 0.08 0.10 0.04 0.06 0.08 0.10 0.04 0.06 0.08 0.10 0.06 0.08 0.08 0.10 Leakage current IR - ≤ 0.01 x CR x UR or 0.5 µA whichever is greater ≤ 0.1 x CR x UR or 10 µA whichever is greater ≤ 0.125 x CR x UR or 12.5 µA whichever is greater (1) Note: (1) Measured at category voltage Document Number: 42074 Revision: 12-Jun-06 For technical questions, contact: eurotant@vishay.com www.vishay.com 135 ETPW Resin-Coated, Radial-Leaded Solid Tantalum Capacitors Vishay Sprague LEAD STYLES AND PACKAGING AMMO PACKAGING (mm) REEL PACKING 191 - 201 CARD BOARD CLAMP INNERLAYER PAPER PROTECTIVE TAPE TAPED PARTS 0 0- 33 32 41 - 4 5 CODE RM in mm ± 0.5 1-6 00 2.5 / 5 1 - 4 (1) C0 5 CASE SIZE SPECIFICATION REMARKS Bulk Form L, Bulk 1-6 V0 5 1 - 4 (1) W0 2.5 Reel, positive pole in front of unreeling direction Form DS, Bulk 1 - 4 (1) T0 2.5 Reel, negative pole in front of unreeling direction 1 - 4 (1) H0 2.5 Ammo 1-5 V2 5 Reel, positive pole in front of unreeling direction 1-5 R0 5 Reel, negative pole in front of unreeling direction 1-5 08 5 Ammo Reel with positive pole in tape run direction in front is standard Note: (1) 100 µF - 6.3 V, 68 µF - 10 V, 47 µF - 16 V, 22 µF - 25 V CASE SIZE BULK 00, V0, C0 REEL W0, T0, V2, R0 AMMO H0, O8 ETPW 1 A,B 500 2500 2500 ETPW 2 C,D,E 500 2000 2000 ETPW 3 F,G 500 1500 1500 ETPW 4 H 500 1500 1500 ETPW 5 J,K,L 100 500 500 ETPW 6 M,N,P, R 100 - - www.vishay.com 136 For technical questions, contact: eurotant@vishay.com Document Number: 42074 Revision: 12-Jun-06 ETPW Resin-Coated, Radial-Leaded Solid Tantalum Capacitors Vishay Sprague TAPING ACCORDING TO IEC 286-2 (meets IEC 286-2) P2 P2 P P Δh ΔP H2 P1 F H P1 F W2 H0 L W0 W1 W t P0 UNREELING DIRECTION D0 Dimensions for components on tape and tolerances: DESIGNATION SYMBOL DIMENSIONS (mm) Holding tape width W 18.0 (+ 1/- 0.5) Adhesive tape width W0 Min. 5.0 Distance of components P 12.7 ± 1 Hole center to component center P2 6.35 ± 1.3 Hole center to lead P1 5.1/3.8 ± 0.7 Distance of body to hole center H (1) 18.0 (+ 2/- 0) Distance of lead to hole center H0 16.0 ± 0.5 Component upper edge to hole center H1 Max. 32.0 Adhesive tape location W2 Max. 3.0 Hole location W1 9.0 (+ 0.75/- 0.5) Distance of holes P0 12.7 ± 0.3 Hole diameter D0 4.0 ± 0.3 Lead diameter d 0.5 ± 0.05 Component alignment Δh Max. ± 2.0 Pitch F 2.5/5.0 (+ 0.6/- 0.1) Holding tape thickness t 0.5 ± 0.2 Component alignment ΔP Max. ± 1.3 L Max. 11.0 Length of snipped leads Note: (1 ) also available: 16 mm and 20 mm taping according to DIN-IEC 286 part 2 Document Number: 42074 Revision: 12-Jun-06 For technical questions, contact: eurotant@vishay.com www.vishay.com 137 ETQW Vishay Sprague Resin-Coated, Radial-Lead Tantalum Capacitors FEATURES • • • • • • • • • MECHANICAL SPECIFICATIONS RoHS Compliant design available Flame retardant encapsulation Very high temperature range Improved humidity class Very low leakage current Very high CV product Very low leakage current Very low failure rate Preaged under temperature and voltage Pb-free Available RoHS* COMPLIANT Tantalum capacitors with sintered anode and solid semiconductor electrolyte with flame retardant fluidized bed coating. The type ETQW is characterized by very favorable electrical values even at higher ambient temperatures. The capacitor complies with DIN 45910 part 147. This type is also available as a radially taped version. Colour: Gold Laser Marked: Capacity and voltage in clear text; Plus pole marked, Date code (year/month) according to DIN IEC 62 Leads: Standard (Tin/Lead), RoHS Compliant (100 % Tin) ORDERING INFORMATION Q1B TYPE ETQW 1A .... ETQW 6R 685 CAPACITANCE 603 DC VOLTAGE RATING AT + 85 °C M CAPACITANCE TOLERANCE 00 LEAD STYLE AND PACKAGING Expressed in picofarads. The first two digits are significant figures. The third is the number of zeros following. Expressed by zeros if needed to complete the 3 digit block. A decimal point is indicated by an “0“ (603 = 6.3 V) M = ± 20 % K = ± 10 % See Lead styles and packaging table D E3 RoHS COMPLIANT E3 = 100 % tin termination (RoHS compliant design) Blank = SnPb termination (standard design) DIMENSIONS in millimeters BASIC VERSION D FORM DS FORM L D D 1.1 ± 0.1 H2 5.5 ± 0.5 Ød 4.5 ± 1.5 15 ± 5 H2 H D RM ± 0.5 RM ± 0.5 MODEL ETQW - 1 ETQW - 2 ETQW - 3 ETQW - 4 ETQW - 5 ETQW - 6 RM ± 0.5 D MAX. H MAX. RM Ø D ± 0.05 4.5 5.0 6.0 6.5 9.0 9.5 7.5 9.5 10.5 11.5 14.0 17.0 2.5 2.5 2.5 2.5 5.0 5.0 0.5 0.5 0.5 0.5 0.5 0.5 FORM DS RM H2 MAX. 10.5 5 12.5 5 13.5 5 14.5 5 17.0 5 20.0 5 FORM L H2 MAX. 10.5 12.5 13.5 14.5 - RM 5 5 5 5 - * Pb containing terminations are not RoHS compliant, exemptions may apply www.vishay.com 138 For technical questions, contact: eurotant@vishay.com Document Number: 42075 Revision: 12-Jun-06 ETQW Resin-Coated, Radial-Leaded Tantalum Capacitors Vishay Sprague STANDARD RATINGS AND CASE CODES RATED VOLTAGE UR at + 85 °C CR µF 3.0 V 6.3 V 10 V 16 V 25 V 35 V 50 V 0.10 1A 1A 0.15 1A 1A 0.22 1A 1A 0.33 1A 1B 0.47 1A 1B 0.68 1A 2C 1.0 1A 1A 2D 1.5 1A 1B 2E 2.2 3.3 1A 4.7 1A 1B 2C 3F 1B 2C 2D 3G 4H 1A 1B 2C 2D 2E 6.8 1A 1B 2C 2D 2E 3F 5J 10 1A 2C 2D 2E 3F 3G 5L 15 1B 2D 2E 3F 4H 5J 6M 22 2C 2E 3F 3G 5J 5L 6P 33 2D 3F 3G 4H 5K 6M 47 2E 3G 4H 5K 6M 6P 68 3F 4H 5J 5L 6N 100 3G 5J 5L 6N 150 4H 5L 6N 6R 220 5J 6M 6P 330 5L 6P 470 STANDARD RATINGS DIMENSIONS MAX. DCL MAX. Z AT AT 100 kHz + 20 °C, (Ω) (µA) MAX. DF AT 120 Hz + 20 °C CR (µF) CASE CODE 6.8 1A UR = 3 V AT + 85 °C, Surge = 3.9 V . . . UC = 2 V AT + 125 °C Q1A685003(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 5.4 0.06 10.0 1A Q1A106003(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 4.5 0.06 PART NUMBER D MAX. (mm) H MAX. (mm) H2 MAX. (mm) RM ± 0.05 d ± 0.05 15.0 1B Q1B156003(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 3.6 0.06 22.0 2C Q2C226003(*)_ _D 5.0 9.5 12.5 2.5 0.5 0.5 2.9 0.06 33.0 2D Q2D336003(*)_ _D 5.0 9.5 12.5 2.5 0.5 0.8 2.3 0.06 47.0 2E Q2E476003(*)_ _D 5.0 9.5 12.5 2.5 0.5 1.1 1.8 0.06 68.0 3F Q3F686003(*)_ _D 6.0 10.5 13.5 2.5 0.5 1.6 1.4 0.06 100.0 3G Q3G107003(*)_ _D 6.0 10.5 13.5 2.5 0.5 2.4 1.1 0.08 150.0 4H Q4H157003(*)_ _D 6.5 11.5 14.5 2.5 0.5 3.6 0.9 0.08 220.0 5J Q5J227003(*)_ _D 9.0 14.0 17.0 5.0 0.5 5.3 0.7 0.08 330.0 5L Q5L337003(*)_ _D 9.0 14.0 17.0 5.0 0.5 7.9 0.6 0.08 Note: (1) Insert M for ± 20 % tolerance or K for ± 10 % _ _ Lead style and packaging code, see lead style and packaging Document Number: 42075 Revision: 12-Jun-06 For technical questions, contact: eurotant@vishay.com www.vishay.com 139 ETQW Vishay Sprague Resin-Coated, Radial-Leaded Tantalum Capacitors STANDARD RATINGS DIMENSIONS CR (µF) CASE CODE 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 220.0 330.0 1A 1B 2C 2D 2E 3F 3G 4H 5J 5L 6M 6P 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 220.0 1A 1B 2C 2D 2E 3F 3G 4H 5J 5L 6N 6P 2.2 3.3 4.7 6.8 10.0 15.0 22.0 33.0 47.0 68.0 100.0 150.0 1A 1B 2C 2D 2E 3F 3G 4H 5K 5L 6N 6R PART NUMBER D MAX. (mm) H MAX. (mm) H2 MAX. (mm) RM ± 0.05 d ± 0.05 UR = 6.3 V AT + 85 °C, Surge = 7.8 V . . . UC = 4 V AT + 125 °C Q1A475603(*)_ _D 4.5 7.5 10.5 2.5 0.5 Q1B685603(*)_ _D 4.5 7.5 10.5 2.5 0.5 Q2C106603(*)_ _D 5.0 9.5 12.5 2.5 0.5 Q2D156603(*)_ _D 5.0 9.5 12.5 2.5 0.5 Q2E226603(*)_ _D 5.0 9.5 12.5 2.5 0.5 Q3F336603(*)_ _D 6.0 10.5 13.5 2.5 0.5 Q3G476603(*)_ _D 6.0 10.5 13.5 2.5 0.5 Q4H686603(*)_ _D 6.5 11.5 14.5 2.5 0.5 Q5J107603(*)_ _D 9.0 14.0 17.0 5.0 0.5 Q5L157603(*)_ _D 9.0 14.0 17.0 5.0 0.5 Q6M227603(*)_ _D 9.5 17.0 20.0 5.0 0.5 Q6P337603(*)_ _D 9.5 17.0 20.0 5.0 0.5 UR = 10 V AT + 85 °C, Surge = 13 V . . . UC = 6.3 V AT + 125 °C Q1A335010(*)_ _D 4.5 7.5 10.5 2.5 0.5 Q1B475010(*)_ _D 4.5 7.5 10.5 2.5 0.5 Q2C685010(*)_ _D 5.0 9.5 12.5 2.5 0.5 Q2D106010(*)_ _D 5.0 9.5 12.5 2.5 0.5 Q2E156010(*)_ _D 5.0 9.5 12.5 2.5 0.5 Q3F226010(*)_ _D 6.0 10.5 13.5 2.5 0.5 Q3G336010(*)_ _D 6.0 10.5 13.5 2.5 0.5 Q4H476010(*)_ _D 6.5 11.5 14.5 2.5 0.5 Q5J686010(*)_ _D 9.0 14.0 17.0 5.0 0.5 Q5L107010(*)_ _D 9.0 14.0 17.0 5.0 0.5 Q6N157010(*)_ _D 9.5 17.0 20.0 5.0 0.5 Q6P227010(*)_ _D 9.5 17.0 20.0 5.0 0.5 UR = 16 V AT + 85 °C, Surge = 20.8 V . . . UC = 10 V AT + 125 °C Q1A225016(*)_ _D 4.5 7.5 10.5 2.5 0.5 Q1B335016(*)_ _D 4.5 7.5 10.5 2.5 0.5 Q2C475016(*)_ _D 5.0 9.5 12.5 2.5 0.5 Q2D685016(*)_ _D 5.0 9.5 12.5 2.5 0.5 Q2E106016(*)_ _D 5.0 9.5 12.5 2.5 0.5 Q3F156016(*)_ _D 6.0 10.5 13.5 2.5 0.5 Q3G226016(*)_ _D 6.0 10.5 13.5 2.5 0.5 Q4H336016(*)_ _D 6.5 11.5 14.5 2.5 0.5 Q5K476016(*)_ _D 9.0 14.0 17.0 5.0 0.5 Q5L686016(*)_ _D 9.0 14.0 17.0 5.0 0.5 Q6N107016(*)_ _D 9.5 17.0 20.0 5.0 0.5 Q6R157016(*)_ _D 9.5 17.0 20.0 5.0 0.5 UR = 25 V AT + 85 °C, Surge = 32.5 V . . . UC = 16 V AT + 125 °C Q1A105025(*)_ _D 4.5 7.1 10.5 2.5 0.5 Q1A155025(*)_ _D 4.5 7.5 10.5 2.5 0.5 Q1B225025(*)_ _D 4.5 7.5 10.5 2.5 0.5 Q2C335025(*)_ _D 5.0 9.5 12.5 2.5 0.5 Q2D475025(*)_ _D 5.0 9.5 12.5 2.5 0.5 Q2E685025(*)_ _D 5.0 9.5 12.5 2.5 0.5 Q3F106025(*)_ _D 6.0 10.5 13.5 2.5 0.5 Q4H156025(*)_ _D 6.5 11.5 14.5 2.5 0.5 Q5J226025(*)_ _D 9.0 14.0 17.0 5.0 0.5 Q5K336025(*)_ _D 9.0 14.0 17.0 5.0 0.5 Q6M476025(*)_ _D 9.5 17.0 20.0 5.0 0.5 Q6N686025(*)_ _D 9.5 17.0 20.0 5.0 0.5 1.0 1A 1.5 1A 2.2 1B 3.3 2C 4.7 2D 6.8 2E 10.0 3F 15.0 4H 22.0 5J 33.0 5K 47.0 6M 68.0 6N Note: (*) Insert M for ± 20 % tolerance or K for ± 10 % _ _ Lead style and packaging code, see lead style and packaging www.vishay.com 140 For technical questions, contact: eurotant@vishay.com MAX. DCL MAX. Z AT AT 100 kHz + 20 °C, (Ω) (µA) MAX. DF AT 120 Hz + 20 °C 0.5 0.5 0.5 0.8 1.1 1.7 2.4 3.4 5.0 7.6 11.1 16.6 5.4 4.5 3.6 2.9 2.3 1.8 1.7 1.1 0.9 0.7 0.6 0.5 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.08 0.08 0.08 0.5 0.5 0.5 0.8 1.2 1.8 2.6 3.8 5.4 8.0 12.0 17.6 5.9 4.5 3.6 2.9 2.3 1.8 1.4 1.1 0.9 0.7 0.6 0.5 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.08 0.08 0.5 0.5 0.6 0.9 1.3 1.9 2.8 4.2 6.0 8.7 12.8 19.2 6.3 5.4 4.1 2.9 2.3 1.8 1.4 1.1 0.9 0.7 0.6 0.5 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.08 0.5 0.5 0.5 0.7 0.9 1.4 2.0 3.0 4.4 6.6 9.4 13.6 7.7 6.8 5.4 4.1 2.9 2.3 1.8 1.4 1.1 0.9 0.7 0.6 0.04 0.04 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 Document Number: 42075 Revision: 12-Jun-06 ETQW Resin-Coated, Radial-Leaded Tantalum Capacitors Vishay Sprague STANDARD RATINGS DIMENSIONS CR (µF) CASE CODE PART NUMBER D MAX. (mm) H MAX. (mm) H2 MAX. (mm) RM ± 0.05 d ± 0.05 MAX. DCL MAX. Z AT AT 100 kHz + 20 °C, (Ω) (µA) MAX. DF AT 120 Hz + 20 °C UR = 35 V AT + 85 °C, Surge = 45.5 V . . . UC = 23 V AT + 125 °C 0.1 1A Q1A104035(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 34.2 0.04 0.15 1A Q1A154035(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 27.0 0.04 0.22 1A Q1A224035(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 20.7 0.04 0.33 1A Q1A334035(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 16.2 0.04 0.47 1A Q1A474035(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 12.6 0.04 0.68 1A Q1A684035(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 9.0 0.04 1.0 1A Q1A105035(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 7.2 0.04 1.5 1B Q1A155035(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 5.9 0.04 2.2 2C Q2C225035(*)_ _D 5.0 9.5 12.5 2.5 0.5 0.6 4.5 0.06 3.3 2D Q2D335035(*)_ _D 5.0 9.5 12.5 2.5 0.5 0.9 3.2 0.06 4.7 2E Q2E475035(*)_ _D 5.0 9.5 12.5 2.5 0.5 1.3 2.3 0.06 6.8 3F Q3F685035(*)_ _D 6.0 10.5 13.5 2.5 0.5 1.9 1.8 0.06 10.0 3G Q3G106035(*)_ _D 6.0 10.5 13.5 2.5 0.5 2.8 1.4 0.06 15.0 5J Q5J156035(*)_ _D 9.0 14.0 17.0 5.0 0.5 4.2 1.1 0.06 22.0 5L Q5L226035(*)_ _D 9.0 14.0 17.0 5.0 0.5 6.2 0.9 0.06 33.0 6M Q6M336035(*)_ _D 9.5 17.0 20.0 5.0 0.5 9.2 0.7 0.06 47.0 6P Q6P476035(*)_ _D 9.5 17.0 20.0 5.0 0.5 13.2 0.6 0.06 0.1 1A Q1A104050(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 34.2 0.04 0.15 1A Q1A154050(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 27.0 0.04 0.22 1A Q1A224050(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 20.7 0.04 0.33 1B Q1B334050(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 16.2 0.04 UR = 50 V AT + 85 °C, Surge = 65 V . . . UC = 33 V AT + 125 °C 0.47 1B Q1B474050(*)_ _D 4.5 7.5 10.5 2.5 0.5 0.5 12.6 0.04 0.68 2C Q2C684050(*)_ _D 5.0 9.5 12.5 2.5 0.5 0.5 9.0 0.04 1.0 2D Q2D105050(*)_ _D 5.0 9.5 12.5 2.5 0.5 0.5 7.2 0.04 1.5 2E Q2E155050(*)_ _D 5.0 9.5 12.5 2.5 0.5 0.6 5.9 0.04 2.2 3F Q3F225050(*)_ _D 6.0 10.5 13.5 2.5 0.5 0.9 4.5 0.06 3.3 3G Q3G335050(*)_ _D 6.0 10.5 13.5 2.5 0.5 1.3 3.2 0.06 4.7 4H Q4H475050(*)_ _D 6.5 11.5 14.5 2.5 0.5 1.9 2.3 0.06 6.8 5J Q5J685050(*)_ _D 9.0 14.0 17.0 5.0 0.5 2.7 1.8 0.06 10.0 5L Q5L106050(*)_ _D 9.0 14.0 17.0 5.0 0.5 4.0 1.4 0.06 15.0 6M Q6M156050(*)_ _D 9.5 17.0 20.0 5.0 0.5 6.0 1.1 0.06 22.0 6P Q6P226050(*)_ _D 9.5 17.0 20.0 5.0 0.5 8.8 0.9 0.06 Note: (*) Insert M for ± 20 % tolerance or K for ± 10 % _ _ Lead style and packaging code, see lead style and packaging Document Number: 42075 Revision: 12-Jun-06 For technical questions, contact: eurotant@vishay.com www.vishay.com 141 ETQW Resin-Coated, Radial-Leaded Tantalum Capacitors Vishay Sprague PERFORMANCE CHARACTERISTICS 1. Climatic Category: 55/125/56 acc. to IEC 2. Temperature Range: - 55 °C up to + 125 °C with linear voltage derating to category voltage UC 3. Rated Voltage, Category Voltage: 3 V to 50 V; 2 V to 33 V 4. The values apply for + 20 °C. For higher temperatures, the values have to be multiplied with the following factors: TEMPERATURE FACTOR + 50 °C 0.7 + 85 °C 0.5 + 125 °C 0.3 Surge Voltage: 1.3 times of rated voltage at + 85 °C 5. Reverse Voltage (Temporary): 15 % of the rated DC voltage at + 20 °C 10 % of the rated DC voltage at + 55 °C 5 % of the rated DC voltage at + 85 °C 6. Rated Capacitance: 0.1 µF to 330 µF 7. Capacitance Tolerance: ± 20 %, ± 10 %, 8. Leakage Current in µA: Measured at + 20 °C after 5 minutes: ≤ 0.008 x CR x UR or 0.5 µA, whichever is greater 9. Intermediate values can be obtained by linear interpolation. For further notes on AC voltage stress: See general information 12. Service life: > 300.000 h (2) 13. Failure percentage: ≤ 0.3 % within 100 000 h (2) 14. Failure rate (l): ≤ 0.3 10- 7/h = ≤ 30 fit (2) 15. Failure criteria: Catastrophic failure: Short circuit or interruption Dissipation Factor: at 120 Hz and + 20 °C See table Drift failure: DC/C > + 5 - 15 % Z > 3 times initial limit value IR > 5 times initial value + 5 µA 10. Impedance: Measured at 100 kHz and + 20 °C See table. 11. Permissible AC Voltage Stress: The highest permissible AC voltage for the respective frequency may be taken from the brochure “General information”. 16. Characteristics at high and low temperatures (the values shall not exceed the following limits) Note: (2) related to UR, + 40 °C and a circuit resistance of ≥ 3 Ω/V TEST TEMPERATURE - 55 °C + 20 °C + 85 °C + 125 °C ΔC/C < tanδ ≤ 1.5 µF < 10 µF < 100 µF ≥ 100 µF - 10 % - + 12 % + 15 % 0.04 0.06 0.08 0.10 0.04 0.06 0.06 0.08 0.04 0.06 0.08 0.10 0.04 0.06 0.08 0.10 Leakage current IR - ≤ 0.008 x CR x UR or 0.5 µA whichever is greater ≤ 0.08 x CR x UR or 5.0 µA whichever is greater ≤ 0.1 x CR x UR or 6.25 µA whichever is greater (1) Note: (1) Measured at category voltage www.vishay.com 142 For technical questions, contact: eurotant@vishay.com Document Number: 42075 Revision: 12-Jun-06 ETQW Resin-Coated, Radial-Leaded Tantalum Capacitors Vishay Sprague LEAD STYLES AND PACKAGING AMMO PACKAGING (mm) REEL PACKING 191 - 201 CARD BOARD CLAMP INNERLAYER PAPER PROTECTIVE TAPE TAPED PARTS 0 0- 33 32 41 - 4 5 CODE RM in mm ± 0.5 1-6 00 2.5 / 5 1-6 V0 5 1-4 W0 1-4 T0 1-4 H0 2.5 1-5 V2 5 Reel, positive pole in front of unreeling direction 1-5 R0 5 Reel, negative pole in front of unreeling direction 1-5 O8 5 Ammo 1-4 C0 5 Style “L“ Bulk CASE SIZE CASE SIZE SPECIFICATION REMARKS 2.5 Reel, positive pole in front of unreeling direction 2.5 Reel, negative pole in front of unreeling direction Reel with positive pole in tape run direction in front is standard! Bulk Form DS, Bulk Ammo BULK 00, V0, C0 REEL W0, T0, V2, R0 AMMO H0, 08 500 2500 2500 ETQW 2 C,D,E 500 2000 2000 ETQW 3 F,G 500 1500 1500 ETQW 4 H 500 1500 1500 ETQW 5 J,K,L 100 500 500 ETQW 6 M,N,P,R 100 - - ETQW 1 A,B Document Number: 42075 Revision: 12-Jun-06 For technical questions, contact: eurotant@vishay.com www.vishay.com 143 ETQW Resin-Coated, Radial-Leaded Tantalum Capacitors Vishay Sprague TAPING ACCORDING TO IEC 286-2 (meets IEC 286-2) P2 P2 P P Δh ΔP H2 P1 F H P1 F W2 H0 L W0 W1 W t P0 UNREELING DIRECTION D0 Dimensions for components on tape and tolerances: DESIGNATION SYMBOL DIMENSIONS (mm) Holding tape width W 18.0 (+ 1/- 0.5) Adhesive tape width W0 Min. 5.0 Distance of components P 12.7 ± 1 Hole center to component center P2 6.35 ± 1.3 Hole center to lead P1 5.1/3.8 ± 0.7 Distance of body to hole center H (1) 18.0 (+ 2/- 0) Distance of lead to hole center H0 16.0 ± 0.5 Component upper edge to hole center H1 Max. 32.0 Adhesive tape location W2 Max. 3.0 Hole location W1 9.0 (+ 0.75/- 0.5) Distance of holes P0 12.7 ± 0.3 Hole diameter D0 4.0 ± 0.3 Lead diameter d 0.5 ± 0.05 Component alignment Δh Max. ± 2.0 Pitch F 2.5/5.0 (+ 0.6/- 0.1) Holding tape thickness t 0.5 ± 0.2 Component alignment ΔP Max. ± 1.3 L Max. 11.0 Length of snipped leads Note: (1) also available: 16 mm and 20 mm taping according to DIN-IEC 286 part 2 www.vishay.com 144 For technical questions, contact: eurotant@vishay.com Document Number: 42075 Revision: 12-Jun-06 Notes Vishay Sprague www.vishay.com 145 Notes Vishay Sprague www.vishay.com 146 Online Information For product information and a current list of sales offices, representatives and distributors, visit our website: Worldwide Sales Contacts www.vishay.com The Americas EUROPE United States Germany Vishay Americas One Greenwich Place Shelton, CT 06484 United States Ph: +1-402-563-6866 Fax: +1-402-563-6296 Vishay EUROPE SALES GmbH Geheimrat-Rosenthal-Str. 100 95100 Selb Germany Ph: +49-9287-71-0 Fax: +49-9287-70435 Asia France Singapore Vishay S.A. 199, BLVD DE LA MADELEINE 06003 NICE, CEDEX 1 France Ph: +33-4-9337-2920 Fax: +33-4-9337-2997 Vishay intertechnology Asia Pte Ltd. 25 Tampines Street 92 Keppel Building #02-00 Singapore 528877 Ph: +65-6788-6668 Fax: +65-6788-0988 P.R. China Vishay Trading (Shanghai) Co., Ltd. 15D, SUN TONG INFOPORT PLAZA 55 HUAI HAI WEST ROAD SHANGHAI 200030 P.R. China PH: +86-21-5258-5000 FAX: +86-21-5258-7979 UNITED KINGDOM VISHAY LTD. PALLION INDUSTRIAL ESTATE SUNDERLAND SR4 6SU UNITED KINGDOM PH: +44-191-514-4155 FAX: +44-191-567-8262 Japan vishay japan CO., LTD. MG Ikenohata Bldg. 4F 1-2-18, Ikenohata Taito-ku Tokyo 110-0008 Japan Ph: +81-3-5832-6210 fax: +81-3-5832-6260 One of the World’s Largest Manufacturers of Discrete Semiconductors and Passive Components leaded solid electrolyte tantalex® capacitors One of the World’s Largest Manufacturers of Discrete Semiconductors and Passive Components D ata B ook World Headquarters Vishay Intertechnology, Inc. 63 Lancaster Avenue Malvern, PA 19355-2143 United States Copyright © 2008 by Vishay Intertechnology, Inc. Registered Trademarks of Vishay Intertechnology, Inc. All rights reserved. Printed in Germany. Specifications subject to change without notice. w w w. v i s h a y. c o m VSE-DB0029-0805
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Tagged PDF : No XMP Toolkit : 3.1-701 Create Date : 2008:04:30 09:18:01+02:00 Metadata Date : 2009:02:03 11:35:40+01:00 Modify Date : 2009:02:03 11:35:40+01:00 Creator Tool : Adobe InDesign CS3 (5.0) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 7174 bytes, use -b option to extract) Instance ID : uuid:bb0fa9e8-58f2-45da-b0e0-4bbda9fea69c Document ID : adobe:docid:indd:b41423ad-15fc-11dd-931c-b34dc233d784 Rendition Class : proof:pdf Derived From Instance ID : b41423ac-15fc-11dd-931c-b34dc233d784 Derived From Document ID : adobe:docid:indd:4717c25e-176e-11dd-9a09-931e04b869c6 Manifest Link Form : ReferenceStream Manifest Placed X Resolution : 300.00 Manifest Placed Y Resolution : 300.00 Manifest Placed Resolution Unit : Inches Manifest Reference Instance ID : uuid:34DC82328316DD118E8FD46C7F1D4C79 Format : application/pdf Producer : Adobe PDF Library 8.0 Trapped : False Has XFA : No Page Count : 153 Creator : Adobe InDesign CS3 (5.0)EXIF Metadata provided by EXIF.tools