A Simple CMOS Camera For Itsy WRL TN 58

WRL-TN-58 WRL-TN-58

WRL-TN-58 The Eye | File Listing

User Manual: WRL-TN-58

Open the PDF directly: View PDF .
Page Count: 13

February 2001

Joel F. Bartlett

Western Research Laboratory 250 University Avenue Palo Alto, California 94301 USA

The Western Research Laboratory (WRL), located in Palo Alto, California, is part of Compaq’s Corporate

Research group. WRL was founded by Digital Equipment Corporation in 1982. We focus on information tech-

nology that is relevant to the technical strategy of the Corporation, and that has the potential to open new business

opportunities. Research at WRL includes Internet protocol design and implementation, tools to optimize com-

piled binary code files, hardware and software mechanisms to support scalable shared memory, graphics VLSI

ICs, handheld computing, and more. As part of WRL tradition, we test our ideas by extensive software or hard-

ware prototyping.

We publish the results of our work in a variety of journals, conferences, research reports, and technical notes.

This document is a technical note. We use technical notes for rapid distribution of technical material; usually this

represents research in progress. Research reports are normally accounts of completed research and may include

material from earlier technical notes, conference papers, or magazine articles.

You can retrieve research reports and technical notes via the World Wide Web at:

http://www.research.compaq.com/wrl/

You can request research reports and technical notes from us by mailing your order to:

Technical Report Distribution

Compaq Western Research Laboratory

250 University Avenue

Palo Alto, CA 94301 U.S.A.

You can also request reports and notes via e-mail. For detailed instructions, put the word “Help” in the sub-

ject line of your message, and mail it to:

WRL-techreports@pa.dec.com

A Simple CMOS Camera for Itsy

Joel F. Bartlett*

Abstract

Itsy is a high-performance platform for research in

“off-the-desktop” computing. One of the attributes of the

base hardware is that it can easily be extended through the

use of “daughter cards.” This technical note describes the

packaging and electronics for one such extension: a simple

CMOS camera.

1. Introduction

Itsy[2] is a flexible, high performance handheld com-

puter designed for research in “off-the-desktop” computing.

Approximately the size of a Palm V, it has a 200MHz Intel

StrongARM 1100 processor, 32 MB of RAM, 32 MB of

flash memory, and runs Linux. Hardware extension is done

by building daughter cards that interface directly to the

memory bus and the StrongARM GPIOs.

As CMOS “camera on a chip” image sensors have be-

come available, there has been significant interest in inte-

grating cameras into handheld devices. Itsy’s memory size

and performance also suggest that it could be more than

just a simple camera. It could act as a handheld computer

vision platform, capable of significant image processing at

the time a picture is taken. In addition, public interest in

Itsy has exposed project members to some opportunities for

powerful, camera-centric, handheld devices.

With this motivation, an effort was started to add a

snapshot camera to Itsy with an eye towards demonstrating

an innovative way to integrate a camera into a handheld

device, and encouraging its use. The goal of this effort was

to minimally impact the Itsy base system, yet not compro-

mise the image sensor’s performance. While many digital

cameras use specialized image processing electronics[4],

this camera would use Itsy’s existing processor and mem-

ory for all image processing and control functions. In the

sections that follow, the package and electronics design

will be discussed, and the paper will close with a few sam-

ple images and comparisons to other systems.

2. Package Design

The starting point for the design was the base Itsy sys-

tem shown at the top of Figure 1. Working with the exist-

ing base electronics and minimizing redesign of the case,

Studio Red created the design shown at the center and bot-

tom of Figure 1. The CMOS imager and lens are contained

in a hinged extension to the left end of the case that length-

ens it by 29mm. The rest of the electronics are contained

on a daughter card that thickens the case by 4.5mm.

Figure 1: Three Itsy Pocket Computers. At the top of

the picture is an unmodified Itsy. It is 118mm x 65mm

x 16mm, and weighs (including battery) 130g with a

molded plastic case. Below it are two units with the

camera extension that are 147mm x 64mm x 20.5mm

and weigh (including battery) 195g with a SLA epoxy

case, or 267g with a NC tooled aluminum case.

Itsy’s reflective gray-scale display is used as the view-

finder, displaying in real-time the scene in front of the lens.

Typically when the camera is used, the photographer holds

the display horizontally in their hand at a good viewing

angle. The lens/imager assembly is then rotated into a ver-

tical position so the lens points forward (middle of Figure

1) at the subject. The hinge allows smooth motion through

180° so the display viewing angle need not be compro-

mised to correctly position the lens. When the camera is

not in use, the lens/imager assembly is folded flat (bottom

* Compaq Computer Corporation Western Research Labo-

ratory, 250 University Avenue, Palo Alto, CA 94301.

joel.bartlett@compaq.com.

WRL TECHNICAL NOTE TN-58 A SIMPLE CMOS CAMERA FOR ITSY

of Figure 1) and the camera is easily stored in a purse or

pocket.

There is minimal interference with other Itsy function

as the unit fits as well in the hand as an unmodified Itsy.

The least objectionable way to increase the size of Itsy is to

lengthen it as has been done here. The camera has a mini-

mal impact on the unit’s width and height.

This view camera inspired design has a number of ad-

vantages. First, since the reflective display is illuminated

by ambient light that is typically overhead, the preferred

viewing position is approximately horizontal, which is how

the camera uses it.

Like a camcorder with an LCD viewer, the camera de-

sign allows the photographer to remain in eye contact with

the subject and allows others to look over the photogra-

pher’s shoulder while they are composing the picture.

Finally, the camera can be used in a variety of ways. It

can be placed on a table in front of the photographer for

unobtrusive candid shots. The lens/imager assembly can be

rotated up to 180° for use in making greater than 1:1 close-

up shots, or not rotated at all (bottom of Figure 1) and the

camera used for self-portraits.

3. Inside the Package

In order to implement this design, the camera’s elec-

tronics are segmented into two circuit boards as shown in

Figure 2. The board on the left contains the CMOS image

sensor and the lens. In order to minimize the width of this

board, a conventional lens mount that surrounds the image

sensor was not used. Instead, an aluminum tube is glued

directly to the glass cover of the image sensor and the lens

is threaded into it. Opaque plastic tape is applied around

the tube to prevent extraneous light from entering the im-

age sensor as shown in Figure 4.

Figure 2: Image sensor and daughter card electronics.

The lens was chosen with the idea of using the camera

for snapshots. The lens is a Sunex DSL900C f/3.0 9.9mm

lens. It can be focused from infinity to closer than 2” by

rotating it. Quality color images require an infrared filter,

so the final component of the lens assembly is a Sunex

IRC21-8R IR cut-off filter that is directly bonded to the

glass cover of the image sensor. Since there is no variable

aperture or auto focus system, the camera operates silently.

The rest of the electronics that control the image sen-

sor and provide the datapath to memory are located on the

daughter card shown on the right side of Figure 2.

The camera is assembled as shown in Figures 3 and 4.

In Figure 3, the daughter card is attached to the Itsy moth-

erboard. The daughter card’s impact on the thickness of

the camera is minimized by careful selection and placement

of its components so that they fit in the space available

between the daughter card and the motherboard. A thirty-

wire 0.5mm flat flex cable connects the daughter card and

the image sensor. In order to thread this cable through the

hinge, two wires are removed and the cable split as show in

Figures 3 and 4.

Figure 3: Itsy shown face down with the case back off,

the daughter card installed, and cabled to the image

sensor card.

Figure 4: Itsy shown face up with the front of the im-

age sensor case removed.

Even the simplest cameras have moving parts. Here,

the lens is rotated in its mount to focus it, and the image

sensor/lens arm rotates on a hinge connecting it to the main

body of the camera. Based on experience with other cam-

eras and electronics, users have an expectation about how

things should move: freely without overshoot, yet hold

their position when stopped. This is accomplished by lu-

bricating the joint with the appropriate grade of damping

WRL TECHNICAL NOTE TN-58 A SIMPLE CMOS CAMERA FOR ITSY

grease: Nyogel 774VL on the lens threads and Nyogel PG-

44A on the body hinge.

With this overview of the package design and electron-

ics segmentation complete, attention can now turn to the

details of the electronics.

4. Photobit PB-0300 CMOS Image Sensor

The design of the electronics was driven by the capa-

bilities and requirements of the PB-0300[5] image sensor.

With only a few digital controls, and external VCC and

clock, this “camera-on-a-chip” can produce digital output

at up to 30 frames/second with VGA (640H x 480V) reso-

lution. Unlike earlier CCD image sensors, this sensor re-

quires no external control circuitry, analog-to-digital con-

verters, or non-standard reference voltages as these

functions are integrated into the sensor chip. The sensor’s

integral gain and exposure controls allow pictures to be

taken under widely varying lighting conditions without the

need for an adjustable aperture lens or a mechanical shut-

ter. The “Image Sensor” schematic details the interface to

the PB-0300. Signal names are shown in a sans-serif font

and those signals that are active low have a “~” as the first

character of their name. The signals of interest are:

GND ground

VCC analog and digital power

CLKIN 24 MHz master clock input

STANDBY active high to set chip on standby

~RSTPB active low to reset the chip

SDATA Serial Host Interface Port™ data

SCLK Serial Host Interface Port™ clock

PIXCLK pixel clock for output data

LINEVLD active high on image data output

FRAMEVLD active high during image processing

DOUT0 data output bit 0 (LSB)

DOUT1 data output bit 1

DOUT2 data output bit 2

DOUT3 data output bit 3

DOUT4 data output bit 4

DOUT5 data output bit 5

DOUT6 data output bit 6

DOUT7 data output bit 7 (MSB)

Finding an appropriate method for supplying power to

the PB-0300 required some experimentation as analog and

digital power levels for the chip are specified at 5.0V.

While it will produce acceptable pictures at lower voltages,

it cannot produce them when powered by Itsy’s 3.05V sys-

tem power. One solution would be to use a charge pump to

produce 5.0V power. This was rejected because it was

expected that future 3.3V “camera-on-a-chip” devices

would be available from Photobit and other vendors and

that signal level conversions, required in a mixed voltage

system, would complicate the system.

Instead, a linear regulator is used to convert the raw

battery voltage to 3.3V that is used to power both the ana-

log and digital portions of the image sensor. This provides

a high enough voltage to provide good pictures, yet is close

enough to the level of Itsy’s system power to allow signals

(but not power connections!) to freely cross between the

image sensor and the rest of the system. The sensor power

is noticeably cleaner than the Itsy system power and this

helps improve picture quality. Not obvious on the sche-

matic are the separate analog and digital power and ground

planes that are provided on the image sensor’s circuit board

to further reduce noise.

5. Itsy Daughter Card Interface

The interface to the Itsy daughter card[9] provides ac-

cess to all the unused StrongARM 1100[3] GPIOs (general

purpose I/O pins) and to the full memory address and data

buses. In the interest of building the simplest interface

possible, the only control logic on the daughter card is for

functions that could not be handled by the Linux driver.

The STANDBY, ~RSTB, FRAMEVLD, SCLK, and

SDATA signals from the PB-0300 are directly connected to

dedicated GPIO pins. The flexibility of the StrongARM

GPIOs allows the Serial Host Interface Port™ (SHIP) pro-

tocol (compatible with I²C™) to be implemented entirely

by the driver.

The bulk of the logic on the daughter card is dedicated

to moving data from the PB-0300 to the StrongARM mem-

ory bus. The FIFO is two 8-bit pixels wide and is imple-

mented by a dual 2,048 x 9 IDT72V83 asynchronous FIFO

that is directly connected to bits 0-15 of the memory bus.

Since the FIFO is the only register that need be read or

written, a minimal control design suffices. The FIFO is

visible to the StrongARM as static memory bank 3, and the

static memory control register is configured as follows (as-

suming a 100 MHz memory clock):

RTx 0: nonburst ROM or Flash EPROM

RBWx 0: 32 bit ROM bus width

RDFx 1: 2 clocks from address to data valid

RDNx 0: ignored as device is not written

RRRx 1: 2 clocks to get off the bus

When configured this way, any read (or write access)

to any physical address in static memory bank 3 results in

~DCCS3 (an active low selecting the memory back) being

asserted by the StrongARM, which starts the read cycle on

the FIFO and two pixels are transferred to the memory bus.

The FIFO is reset and status information is communi-

cated to the StrongARM by four dedicated GPIO pins:

~RSTFIFO active low that resets both FIFOs

~FULL active low on FIFO overflow

~EMPTY active low on FIFO empty

~HALF active low on FIFO half full

The final GPIO control signal to the daughter card is

~CAMERA. This is an active low that turns on the clock

and linear regulator for the PB-0300, and enables the

WRL TECHNICAL NOTE TN-58 A SIMPLE CMOS CAMERA FOR ITSY

daughter card memory interface. When the camera is not

in use, this signal is high to disable these components and

save power.

With these signals defined, attention will now shift to

using them to take a picture.

6. Taking a Picture

The camera is visible to application programs as the

device /dev/pb0300. When it is opened, the driver sets

~CAMERA to 0. This starts the 24 MHz clock, supplies

power to the PB-0300, and enables the daughter card mem-

ory interface.

The application starts by issuing an ioctl (I/O control

command) to reset the camera. The driver implements this

operation by pulsing ~RSTPB. This initializes the PB-

0300 and runs it in its default configuration, where it sup-

plies the StrongARM with 30 VGA size images/second.

Before taking pictures, the application may need to

make configuration changes on the PB-0300. This is done

by issuing a number of ioctl requests to read and write the

PB-0300’s registers. The driver performs these functions

via a software implementation of the SHIP protocol using

the SCLK and SDATA GPIOs. The Itsy is the protocol

master and it provides the clock via SCLK, a dedicated

output pin. Clock pulse duration is controlled by busy wait-

ing in the driver, using the StrongARM’s 3.6864 MHz op-

erating system timer. Both Itsy and the PB-0300 use the

SDATA line to transfer data a bit at a time. Typically,

SDATA is configured by the driver as an input pin, so its

value is either driven by the PB-0300 or driven to 1 by the

pull up resistor. The only time Itsy drives this signal is

when the protocol requires the driver to write a 0 data

value, in which case it forces SDATA to 0 by configuring it

as an output pin with a value of 0 for one bit time. Addi-

tion ioctl commands are used to allocate image buffers in

the driver and select the mode of operation: still picture or

video clip.

Once PB-0300 configuration is complete, the applica-

tion issues a read request to the device to take a picture.

This is posted in the driver, but no action is taken until a

falling edge on FRAMEVLD causes an interrupt. The PB-

0300 is now between frames and not trying to transfer any

data into the FIFO, so the FIFO can be reset by pulsing

~RSTFIFO. The interrupt handler completes by enabling

falling edge interrupts on ~FULL and ~HALF.

As pixel values are generated by the PB-0300, they are

moved into memory in the following manner (see the

“DC/FIFO” schematic). When PIXCLK falls to 0 and

LINEVLD is 1, pixel data is available at DOUT[0..7] and

~WRITE falls to 0.

When ~WRITE falls, data is latched in the octal D-

type latch (IC1 74373) and either ~WRITE07 or

~WRITE815 falls to 0 which starts the transfer of the

latched data into the appropriate half of the FIFO.

When ~WRITE rises to 1, the value of the D-type flip

flop (IC12A 7474) is inverted which results in the other

half of the FIFO being selected for holding the next pixel.

When the FIFO become half full, ~HALF falls to 0

which interrupts the processor. The interrupt handler then

reads 2048 pixels from the FIFO and stores them into

memory. The FIFO is visible to the processor as static

memory bank 3. Each load from a virtual address mapped

to this bank causes ~DCCS3 to fall to 0, and the FIFO

places two pixels of data (16 bits) onto the memory data

bus. After the PB-0300 outputs the last pixel of the image,

FRAMEVLD drops to 0, which interrupts the processor.

The FIFO is emptied into the driver’s buffer and then the

read completes. If the driver is configured to record a

video clip, then the interrupt handler will start the next read

so no frames are lost. Otherwise, it will disable the FIFO

interrupts as the PB-0300 images are being ignored.

7. Processing the Image Data

A picture appears to the application program as a VGA

sized (640 x 480) array of unsigned bytes. Cameras im-

plemented using the monochrome version of the PB-0300

require no further processing as this array is the gray-scale

image. Color cameras require additional processing as the

image sensor is covered by a color filter array as shown in

Figure 5. Each pixel in the image sensor looks through a

red, blue, or green color filter and returns that value. When

printed as color image, since each pixel has only a red,

green, or blue value, the result is like that shown in Figure

6. In order to produce RGB values for each pixel, the miss-

ing color values are recovered by interpolation[1] and the

result is shown in Figure 7.

Since the camera does not have dedicated image proc-

essing electronics, in camera color recovery is application

dependent or can be deferred until after the images have

been removed from the camera.

Figure 5: A portion of the Bayer Pattern of the PB-

0300 color filter array, where each colored square is a

color filter covering one pixel.

WRL TECHNICAL NOTE TN-58 A SIMPLE CMOS CAMERA FOR ITSY

Figure 6: A magnified portion of an image returned by

a color PB-0300, where each pixel has only a red,

green, or blue value.

Figure 7: Image color recovery from the image data of

Figure 6 using a simple pixel-averaging algorithm.

8. Initial Applications

Software to implement simple still and video cameras

has been implemented. Three still pictures taken by the

camera are displayed in Figure 9. They demonstrate the

picture quality available from the camera and its ability to

take close-ups.

Since the camera is capable of recording successive

images, short video sequences (limited only by the size of

Itsy’s memory) can also be recorded. By selecting an im-

age size smaller than VGA, frame rates faster than 30

frames/second are possible. One example, is a short feature

called “The Break”, Figure 10, where CIF size images

(352W x 288H) were shot at 60 frames/second in two two-

second long bursts. A slow motion QuickTime movie was

then assembled using Adobe ImageReady.

Figure 9: Three sample still images: an outdoor scene,

a shop window, and a well-worn quarter.

WRL TECHNICAL NOTE TN-58 A SIMPLE CMOS CAMERA FOR ITSY

Figure 10: “The Break” shows a pool break at 1/12

real-time. In this frame, the cue ball has just hit the

head of the rack

The most interesting application for the Itsy camera is

handheld computer vision. To demonstrate this, our col-

leagues at Compaq’s Cambridge Research Laboratory sup-

plied a neural network-based face detector[6] that detects

any number of frontal, upright faces in an image. The de-

tector was paired with the Itsy still camera code and the

result is a “face finding camera” whose results are shown in

Figure 11.

Figure 11: After taking a picture, the “face finding

camera” draws a rectangle around each frontal, upright

face it finds in the image.

Another application that could easily be hosted on an

Itsy with a camera is the gesture pendant[8] designed at

Georgia Tech. This is a wearable camera that contains

sufficient processing power to recognize hand signals and

convert them into control commands to nearby appliances.

It was prototyped using a video camera, a 900MHz video

transmitter/receiver pair, and a desktop computer. Since

Itsy has sufficient processing power and memory to recog-

nize a gesture, its camera could capture the gesture, and its

IRDA link could directly control the desired appliance.

Lest one think the power required for such a device is

impossible in a wearable device, the Itsy still camera soft-

ware that uses the display as a real-time viewfinder is able

to continuously run for three hours before discharging the

standard 2.2 watt-hour battery.

9. Related Work and Extensions

With the Itsy camera’s design in mind, attention can

now turn to putting it in context with related work. One of

WRL’s research partners at EPFL integrated a mobile cam-

era[7] into Itsy. Their electronics were more complex than

those described in this paper as they were interfacing two

sensor chips with less integrated functions that the PB-

0300.

Two commercially available cameras for handheld sys-

tems are the Kodak PalmPix™ for Palm and the eyemod-

ule™ for the Handspring™ Visor™. The PalmPix image

sensor is the same size as Itsy’s, but the display must be

held vertically in a poor viewing position in front of the

user’s face in order to operate it. The eyemodule’s display

is held in a horizontal position like Itsy’s for good viewing,

but its image sensor is only 320x240 pixels. The major

limitations of each of these designs are processor perform-

ance and camera-to-memory bandwidth. The low perform-

ance processors in both handhelds require that the camera

extensions provide dedicated image processing electronics.

The camera is in turn connected to the processor on both

systems by a 115,200 bit/second serial interface. Contrast

this with Itsy, where the camera is directly connected to the

StrongARM memory bus and is capable of sustained trans-

fers at 8.8Mbytes/second (640x480 pixel frames at 30

frames/second). This bandwidth is clearly required for

taking video clips, but it is also desirable to provide real-

time updates to the viewfinder.

While this camera is centered on the Photobit PB-

0300, the design could be easily adapted to a number of

other CMOS image sensors. For example, the Agilent

HDCS-2030, the Kodak KAC-0310, and the Zoran Pixel-

cam PCS2112 all are powered at 3.3V, have I²C compatible

controls, and provide digital image output data. Minimal

changes to the electronics would be required to control any

of these chips.

10. Conclusions

The camera extension of Itsy is a success. The

changes to the base Itsy unit have been minimized, yet the

resulting object is pleasing to the eye and encourages users

to pick it up. It produces pictures of acceptable quality and

the utility and power of the system are demonstrated by the

initial computer vision experiments. The positive results

and the simplicity of the design should encourage others to

integrate cameras into their “off-the-desktop” systems.

WRL TECHNICAL NOTE TN-58 A SIMPLE CMOS CAMERA FOR ITSY

Acknowledgements

This work would not have been possible without the

skills and interest of my colleagues at WRL: William

Hamburgen, Marc Viredaz, Wayne Mack, Deborah A.

Wallach, Lawrence Brakmo, and Andreas Nowatzyk. Stu-

dio Red turned the project’s unfocused ideas about a view

camera into a striking design and functional prototype

packages. Jim Rehg and Uli Kremer provided the neural

network-based face detector. Wendy Bartlett provided edi-

torial assistance for this technical note. I thank you all.

References

[1] Jim Adams, Kevin Parulski, and Kevin Spaulding.

Color Processing in Digital Cameras, IEEE Micro,

November-December 1998, pp 20-29.

[2] Joel F. Bartlett, Lawrence S. Brakmo, Keith I. Farkas,

William R. Hamburgen, Timothy Mann, Marc A.

Viredaz, Carl A. Waldspurger, and Deborah Wallach.

The Itsy Pocket Computer. Research report 2000/6,

WRL, Compaq, Palo Alto, CA (USA), October 2000.

[3] Intel. Intel® SA-1100 Microprocessor Technical Ref-

erence Manual, September 1998, available via

www.intel.com.

[4] Shoji Kawamua, Capturing Images with Digital Still

Cameras, IEEE Micro, November-December 1998,

pp 14-19.

[5] Photobit Corporation. PB-0300 1/3-inch CMOS Ac-

tive-Pixel Digital Image Sensor, March 2000 (Version

3.0), available via www.photobit.com.

[6] H. A. Rowley, S. Baluja, and T. Kanade. Neural Net-

work-Based Face Detection. IEEE Transactions on

Pattern Analysis and Machine Intelligence, Vol. 20,

No. 1, 1998, pp 23-38.

[7] Olivier Saudan. Interfacing a mobile camera with the

Itsy pocket computer. 7

th semester project, LAMI,

EPFL, Lausanne (CH), February 1999.

[8] Thad Starner, Jake Auxier, Daniel Ashbrook, and

Maribeth Gandy. The Gesture Pendant: A Self-

illuminating, Wearable, Infrared Computer Vision

System for Home Automation Control and Medical

Monitoring. In The Fourth International Symposium

on Wearable Computers, IEEE, October 2000, pp 87-

94.

[9] Marc A. Viredaz. The Itsy Pocket Computer Version

1.5: User’s Manual. Technical Note TN-54, WRL,

Compaq, Palo Alto, CA (USA), July 1988.

Bill of Materials

Components labeled “Cn” and “Rn” are capacitors and

resistors whose value is as shown on the schematic. Com-

ponents labeled “JPn” are test points. The rest of the com-

ponents are as follows:

Sensor Circuit Board

CON1 Hirose 30-pin 0.5mm top contact

connector

IC1 PB-0300CCC

L1 & L2 600 ohm @ 100MHz ferrite beads join

split power and ground planes

DC/FIFO Circuit Board

CON1 Hirose 30-pin 0.5mm bottom contact

connector

DC1 daughter card connector

IC1 74LCX373FN octal D-type latch

IC2 IDT72V83L15PA dual 2,048 x 9 FIFO

IC3 74LCX14FN hex Schmitt inverter

IC9 SG636 PCE 24MHz oscillator

IC10 TC1015_33VCT regulator

IC11 74LCX32FN quad 2-input or

IC12 74LCX74FN dual D flip-flop

L1 600 ohm @ 100MHz ferrite bead

R1 & R3 0.1-ohm precision resistors for power

measurement

WRL TECHNICAL NOTE TN-58 A SIMPLE CMOS CAMERA FOR ITSY

A Simple CMOS Camera For Itsy WRL TN 58

WRL-TN-58 WRL-TN-58

WRL-TN-58 The Eye | File Listing

Navigation menu

Versions of this User Manual:

Views

Navigation