Warmup Trade Brochure

User Manual: Warmup-Trade-Brochure of /wp-content/uploads

Open the PDF directly: View PDF .
Page Count: 100

Download
Open PDF In Browser	View PDF

Electric and hydronic heating portfolio

The world’s best-selling floor heating brand™

4iE

SMART WIFI
THERMOSTAT

For central and underfloor heating

The right temperature. The best tariff.
Effortlessly.

3 YEAR*
LIMITED

WARRANTY

*Visit www.warmup.co.uk for more details

Table of Contents
Warmup Electric Floor and Wall Heating
System Summary Guide
Warmup’s Unique Product Advantage and the Best Warranties,
Installation Guarantee and Accreditations
About Warmup and our Services

3
4 -5

4 Easy Steps to Calculate your Underfloor Heating Requirements

6-7
8
9
10 - 13
14 - 29
30 - 33
34 - 35
53

Thermostats

Page

World Leading Research and Development
Benefits of Underfloor Heating
Warmup Cement Coated Tough Insulation Boards
Heating Systems
Warmup Insulated Underlay/Dual Overlay
Warmup Electric In-Wall Heating Panel

Warmup 4iE Smart WiFi Thermostat
Warmup 3iE Energy-Monitor Thermostat
Warmup Tempo Digital Programmable Thermostat

Accessories

36 - 39
40 - 43
44 - 45

Page
46 - 47
48 - 49

Warmup Mirror Demisters
Warmup Electric Towel Rails

Outdoor Heating Solutions

Page
50
51
52

Snow Melting Cables
Self-Regulating Cable
Patio Heaters

Warmup Hydronic Underfloor Heating
Warmup Hydronic Underfloor Heating Systems - Introduction
Warmup HydroPack Installation Kit
Hydronic Systems - Screed and Concrete Floors
Hydronic Systems - Timber, Suspended and Batten Floors
Hydronic Systems - Total-16 Low Profile System
Warmup Dual Overlay Concrete
Thermostats and Controls
Warmup HydroPack, Thermostats and Controls
Fixings and Ancillary Products
Manifolds, Ancillaries and Fittings
Pipes
Projects Department: A Dedicated Service

FS 586320

2
2

Page

Page
54 - 55
56 - 59
60 - 69
70 - 77
78 - 79
80 - 81
82 - 84
85 - 90
90 - 94
95
96
97 - 99

Exceptional Manufacturer of the Year
London Passport to Export Awards

Call us
us now
now 0845
0845 345
345 2288
2288 or
or visit
visit www.warmup.co.uk
www.warmup.co.uk
Call

System Summary Guide
Whatever the floor finish or subfloor construction, Warmup has
the right underfloor heating solution to match your specific needs.
Use the table below to find out which products best suit your floor
type. Contact us on 0845 345 2288 should you require further
information.
Warmup Electric Products
Loose
Wire
Page
Number

Sticky Sticky
Warmup
Mat
Mat Inscreed Foil
Hydronic
150
200
Cable Heater
Products
Watt Watt

FLOORING TYPE

Tile & Stone
Hardwood
Laminate
Carpet
Vinyl

Call us on 0845 345 2288
to discover how we can help or
chat with us online at
www.warmup.co.uk

Warmup is fully tested and compatible
for use with wood floors and vinyl
including leading brands like:

The
The world’s
world’s best-selling
best-selling floor
floor heating
heating brand
brand

3
3

Warmup’s Unique Product Advantage
Electric
Warmup offers the thinnest dual-fluoropolymer coated
multi-strand heating wire (less than 1.8mm in diameter)
on the market - to enable you to offer your customers the very
best solution. Further, it will not raise floor levels and is BEAB
approved, meeting the highest safety standards. Best of all, it is
quick and easy to install.
1
2
3
4
5

1. Outer Insulation: advanced fluoropolymer
2. Diameter 1.8mm
3. Earth Braid
4. Inner Insulation: advanced fluoropolymer
5. Multi-strand twin conductors/heating element

Hydronic
Warmup offers you a complete bespoke solution
Warmup hydronic heating systems come fully designed and
supplied with a full set of high quality components and controls
ready for installation. Systems are available in a number of
configurations and components guaranteed to perfectly match
your project and budget.
Warmup systems come with a choice of 3 pipe types; PEX-A,
PE-RT and PE-RT/AL/PE-RT. This choice guarantees that
you have the best possible system, tailored to your specific
installation and budget.
Warmup PEX-A hydronic pipe carries a Lifetime Warranty for
greater peace of mind. All other pipes carry a 50 year Warranty.

Call us now 0845 345 2288 or visit www.warmup.co.uk

The Best Warranties, Installation
Guarantee and Accreditations
Warmup Loose Wire, Matting, StickyMat
and PEX-A Systems carry a Lifetime
Warranty for greater peace of mind.
A Lifetime Warranty upgrade is
available on the 4iE Smart WiFi
Thermostat, 3iE Energy-Monitor
Thermostat and Tempo Digital
Programmable Thermostat.

LIFETIME
LIMITED

WARRANTY

If you accidentally damage the heating system during
installation, return it to Warmup and we will replace it with
another heater of the same make and model FREE!
(See www.warmup.co.uk for full details)

Rest assured, you are installing the very best. Warmup is
the only underfloor heating company whose products are
European compliant, CE marked and accredited by all these
independent institutions. In addition, we are members of
BEAMA, CIBSE, Constructionline, RIBA, and the TTA.

FS 586320

17th Edition Approved. All Warmup products comply with
17th Edition of the IET Electrical Requirements BS7671:2012

The world’s best-selling floor heating brand

About Warmup
Warmup is a certified ISO 9001:2008 UK based manufacturing Plc
creating and delivering underfloor heating solutions (electric,
hydronic and hybrid - a mixture of both). We have sold in excess of
2 million systems in more than 60 countries in over 21 years of
trading. We have subsidiary operations in 11 countries and licensed
trading partners in the other countries.
The combination of Warmup’s heating wire with fluoropolymer
coatings (on the inner wires and the outer protective jacket), our
4iE Smart WiFi Thermostat, 3iE Energy-Monitor Thermostat and
Tempo Digital Programmable Thermostat are patented, trade mark
protected, designed and owned by the world’s best selling brand.
We began as, and remain, a knowledge and research driven UK
business, making proprietary, world-leading products.
Warmup has a tradition for quality and innovation. We constantly
update and add to our product range to deliver the absolute best
products.
Warmup is the only underfloor heating company whose products
are European compliant, CE marked and accredited by more
independent institutions than anyone else in the industry, giving
you and your customers security and peace of mind.

FS 586320

Exceptional Manufacturer of the Year
London Passport to Export Awards

Our Services
We are with you every step of the way. Since 1994, Warmup has
provided trade professionals with outstanding services and quality
products through leading retailers, wholesalers and builder
merchants. This includes:

Unique Online “Quick Quote” Service
Let us save you time by calculating the right product, price and size
required for your project. All you need to do is visit our website,
enter a few project details for a no-obligation “Quick Quote”. You
will receive a quotation estimate within a few minutes. Should you
require a more detailed quotation, you can submit your drawings or
plans to www.warmup.co.uk or via fax on 0845 345 2299.

Technical Helpline
We are the only company who offers a technical helpline 24/7/365.
If you have a question or an installation problem, our experienced
Technical Team are available to support you - call 0845 345 2288.
We also offer online ‘live’ chat and a host of installation tutorials www.warmup.co.uk

Call us now 0845 345 2288 or visit www.warmup.co.uk

Repair Kits
Minor damage (i.e. nicking the electric wire with a trowel),
discovered before the floor is laid, can easily be repaired on-site.
Call 0845 345 2288 to obtain an easy-to-fit repair kit, via next-day
delivery (or keep a few extra available).

Running Cost Information
To get an accurate idea of typical running costs of a Warmup System,
see the table below.
2m2

4m2

5m2

10m2

15m2

25m2

1 hr

2.36p

4.72p

5.90p

11.81p

17.71p

29.52p

2 hrs

4.30p

8.61p

10.76p

21.52p

32.28p

53.81p

3 hrs

6.25p

12.49p

15.62p

31.23p

46.85p

78.08p

4 hrs

8.10p

16.20p

20.26p

40.51p

60.77p

101.28p

5 hrs

10.13p

20.26p

25.32p

50.64p

75.96p

126.60p

6 hrs

11.94p

23.89p

29.86

59.72p

89.59p

149.31p

7 hrs

13.93p

27.85

34.82p

69.63p

104.45p

174.08p

8 hrs

15.83p

31.66p

39.57p

79.15p

118.72p

197.87p

Financial figures in £’pence
Notice: Any unauthorised replication of this material, including running cost data,
will constitute an infringement of copyright.

Rapid Delivery
If you need products quickly, ask your supplier to place your order
by 2pm, Monday-Friday and we will ship it the same day for nextworking-day delivery (allow 2-3 days for Scotland and the Channel
Islands). Warmup is fully stocked and available from leading retailers
and trade outlets, throughout the UK.

Warmup Service Engineers
Should your customer’s heating system become damaged after
installation, we offer a team of experienced service engineers, who will
identify and correct the damage. Call Warmup on 0845 345 2288 to
arrange an appointment.

Quotation & Layout Service
Warmup offers a FREE CAD drawing and quotation service to all
customers, regardless of project size. All you need to do is fax your
drawing to 0845 345 2299, email uk@warmup.com or visit www.
warmup.co.uk to access our quotation facility and Warmup will do the
rest.

Training
Warmup provides group training sessions for any sized project, held
at our Head Office in London. Let our trained professionals show you
how quick and easy it is to install Warmup with no need for specialist
trades. It’s FREE - why not upgrade your skills and stand out from your
competitors? Call 0845 345 2288 or email training@warmup.com for
details.

The world’s best-selling floor heating brand

World Leading Research & Development
By continually investing in research and development, Warmup
is able to foresee and respond to upcoming industry trends and
technological developments. This guarantees you fast access to
the latest innovations when it comes to underfloor heating design,
energy efficiency and reducing CO2 emissions.

Warmup Monitored Family Homes Programme
In support of our EN442-2 Research Centre in Germany, we operate
a number of Family Monitored Houses in addition to the BRE
(Building Research Establishment) Renewable House.
This initiative grew out of the need to better predict the future
energy running costs of houses using Warmup underfloor heating
systems. Information is gathered every few minutes from many tiny
sensors.

Bi-climatic chamber in Warmup’s Research Centre in Germany

These sensors are strategically placed in each zone to compare
floor, wire/water and outside temperatures and often other
readings like humidity and radiant temperature. This allows a
detailed view of the amount of energy actually needed to create
ideal living conditions.
This can be compared with test facility results and in particular,
what may have been predicted by SAP (Standard Assessment
Procedure) calculations, which are central to the perceived energy
performance and efficiency of a dwelling.
This information allows us to answer questions from ‘How much
will it cost to run Warmup in my new house?’ to ‘How much will I
save using Warmup underfloor heating rather than radiators in my
home?’
How much does underfloor heating cost to heat my room?
RUNNING TIME
ROOM TYPE

HEATED
AREA

WINTER
COST*

Bathroom

4m2

2hrs

1hr

£24.26

Kitchen

5m2

1hr

2hrs

£30.33

Lounge

15m2

0hrs

3hrs

£85.27

*Assumptions: 12.66p/kWh - system on 6 months (182 days) per year. System installed on 10mm
Warmup Insulation Board. **Avg. running cost after initial heat-up period = 0.85p/m²/hr.
For more details visit www.warmup.co.uk

Call us now 0845 345 2288 or visit www.warmup.co.uk

Benefits of Underfloor Heating
Floor heating is simply the only way to create the ideal comfort
zone in a family room to balance floor and air temperature.
Suitable for every type of project - new-build, refurbishments
and renovations.
Appropriate for use under a wide range of floor finishes - stone,
tile, wood, carpet and vinyl.
Warmup is fully tested and compatible for use with Karndean and
Amtico.
With its low operating temperature, warmth is evenly spread across
the whole floor area, with no cold spots, heating from the floor
upwards without creating a stuffy atmosphere.
Energy efficiency - underfloor heating gives the user control,
provides rapid heat-up and high efficiency heating. It requires
significantly less energy as you are not heating the ceiling area and
it enables the temperature to be accurately controlled as needed,
allowing end users to heat the room(s) they want, with no energy
wasted.
Radiator

Warmup
floor
heating

Temperature control in each zone - comprehensive range of
thermostats, including the 4iE Smart WiFi Thermostat, allows
the end user to choose the temperature levels they require, with
programmable settings (heat on/off) to match their lifestyle.
Cost savings - because underfloor heating uses a lower
temperature than standard radiators, heating costs are reduced and
savings can be achieved by at least 10% on utility bills.
Design freedom - underfloor heating means no bulky radiators to
take up valuable wall and floor space.
Safety - delivers a family-friendly and safe environment. No low
level hot surfaces or hard metal edges that come with a radiator
system, creating a potentially unsafe and dangerous environment
for small children, the elderly or people at risk.
No maintenance - there is no maintenance required for electric
underfloor heating and little or no maintenance required on our
hydronic systems.
Hydronic underfloor heating can be linked to most heat
sources, giving total flexibility - allowing for best energy savings
as new energy efficient heat generators become available, now and
in the future.

The world’s best-selling floor heating brand

Cement Coated
Tough Insulation Boards
Insulate and waterproof in one easy step with
Warmup Insulation Boards. Made from extruded
polystyrene and faced with 0.5mm glassfibre mesh
reinforced polymer-modified cement mortar, they
have a high thermal insulation property for energy
efficiency and an added benefit of sound proofing.
The boards can be used on walls or floors and are
ideal for applications such as dry lining, insulating
and waterproofing in areas such as wetrooms,
bathrooms and kitchens.

Insulation boards prevent heat loss to the subfloor - a warm floor
can be achieved in as little as 20 minutes compared to over 2 hours
with no insulation (see the heat-up chart on page 12 for more
details).
Features

Technical Data

Easy to cut and shape around fixtures with
a knife or saw

Board size:
1,250mm(L) x 600mm(W)

Comes in a range of thicknesses to suit floor
and wall applications. Can be fixed to solid
or stud walls

Thickness:
6mm, 10mm, 20mm, 30mm, 40mm,
50mm

Holds wall tiles up to 62kg/m² and floor
tiles up to 30 tonnes/m²

Composition:
Extruded polystyrene, each side faced
with a nominal 0.5mm thick glassfibre
mesh reinforced polymer-modified
cement mortar

Joints must be sealed to make them
waterproof

R Value:
(6mm) 0.16; (10mm) 0.28;
(20mm) 0.58; (30mm) 0.88;
(40mm) 1.20; (50mm) 1.50

High thermal insulation, resisting heat
loss and increasing the heating system’s
efficiency

Class “0” / “B1” fire rated

Impact sound reduction dl =21

No primer required when used in conjunction with underfloor heating

Ready for tile/plaster – no additional prep
work needed

European compliant and CE marked

Excellent as internal wall insulation
especially when compared to standard
cement building boards and plaster boards

Conforms to Building Regulations Part L

Call us now 0845 345 2288 or visit www.warmup.co.uk

Price Guide

Price (Excl 20% VAT)

Area
Covered

No. of
Boards
Req.

6mm

10mm*

20mm

30mm

40mm

1m2

£34.16

£46.66

£58.32

£66.66

£83.32

2m2

£51.24

£69.99

£87.48

£99.99

£124.98

3m2

£85.40

£116.65

£145.80

£166.65

£208.30

4m2

£102.48

£139.98

£174.96

£199.98

£249.96

5m2

£119.56

£163.31

£204.12

£233.31

£291.62

6m2

£153.72

£209.97

£262.44

£299.97

£374.94

7m2

£170.80

£233.30

£291.60

£333.30

£416.60

8m2

£187.88

£256.63

£320.76

£366.63

£458.26

9m2

£222.04

£303.29

£379.08

£433.29

£541.58

10m2

£239.12

£326.62

£408.24

£466.62

£583.24

11m2

£256.20

£349.95

£437.40

£499.95

£624.90

12m2

£290.36

£396.61

£495.72

£566.61

£708.22

13m2

£307.44

£419.94

£524.88

£599.94

£749.88

14m2

£341.60

£466.60

£583.20

£666.60

£833.20

15m

£358.68

£489.93

£612.36

£699.93

£874.86

16m2

£375.76

£513.26

£641.52

£733.26

£916.52

17m2

£409.92

£559.92

£699.84

£799.92

£999.84

18m2

£427.00

£583.25

£729.00

£833.25

£1,041.50

19m2

£444.08

£606.58

£758.16

£866.58

£1,083.16

20m2

£478.24

£653.24

£816.48

£933.24

£1,166.48

50mm

*Standard board thickness = 10mm

Accessories

Items Required

Price
(Excl 20% VAT)

Glassfibre tape - prevents movement
and covers the joints between boards

One roll per 25
boards

£3.33

WIBS40MM Wooden Screws - 40mm

100 per pack to fix
approximately 5
boards

£3.33

WIBW36MM Penny Washers - 36mm
diameter

50 per pack to fix
approximately
2 boards

£4.99

Installation video for Warmup Insulation Boards.
Always refer to the installation manual prior to commencing your project.

The world’s best-selling floor heating brand

Temperature

Heat-Up Chart

Time in hours
With insulation board
Without insulation board

In testing, heat-up time was cut from over 2 and a half hours to just
20 minutes. This data applies to Warmup heating products only.
* Assumes a system running twice a day for 2 hours on a concrete subfloor
** Source: Warmup tests performed to EN442-2 standards

Installation Guide
(Refer to installation manual for complete instructions)
Installation onto concrete floors
Lay the boards on a concrete base and stagger the joints. Fix the
boards to the concrete base with a suitable flexible tile adhesive.
Once the adhesive hardens, tape the joints with glassfibre tape.
Installation onto wooden floors (Contact us on 0845 345 2288
to receive a copy of our technical guide for wood flooring
or visit www.warmup.co.uk).
On a wooden subfloor, lay the boards and stagger the joints.
Fix with a suitable flexible tile adhesive. When the adhesive has
set but not necessarily dried, fix the boards with a screw fixing and
washer at 200mm spacings. Ensure the screw head is flush with the
surface. Reinforce the joints with glassfibre tape.
Installation onto walls
Fix the lightweight boards to any suitable framework, such as
wood or brick. They are strong, holding a tile weight of 62kg/m²
(double that of plasterboard). Boards can easily be cut with a knife
or sawed, to work around objects. Use 8 galvanised screws per m²
at a minimum of 30mm from edges. Tighten screws until washers
bite the board surface, then level the washer with a rubber mallet.
Cover joints with self adhesive glassfibre tape embedded in a layer
of flexible tile adhesive.

Call us now 0845 345 2288 or visit www.warmup.co.uk

Frequently Asked Questions
Where can I use it?
Floors: Warmup Insulation Boards can be used as a structural tile
backer board on the floor, withstanding a load of 30 tonnes/sqm
and are ideal for use with underfloor heating. We recommend a
minimum thickness of 6mm on a concrete subfloor and 10mm on
a wooden subfloor for floor stability. They offer the added benefit
of high sound proofing properties, which is ideal for rooms above
ground level.
Walls: As wall tile backer boards, tiles can be fixed directly onto the
surface without prior preparation. When the joints are sealed it is
totally waterproof, offering an ideal solution for use in bathrooms,
shower rooms, wetrooms and kitchens.
What is it made from?
Warmup Insulation Boards are made of waterproof extruded
polystyrene and have a glassfibre mesh embedded on each face,
onto a cement polymer adhesive. The boards are fully waterproof,
preventing any water to pass through them in the way expanded
polystyrene boards do. They are lightweight, easy to cut with a
knife and install onto any surface. Being free of harmful asbestos,
they pose no health or safety risks and are unaffected by the freeze/
thaw cycle.
What is an R Value?
The R value is a measure of thermal resistance used in the
construction industry. The higher the R value the better an insulator
(e.g. 10mm Warmup Insulation Boards have an R value of 0.28
m²K/W and the 20mm Warmup Insulation Boards have an R value of
0.58 m²K/W). All buildings should strive for the highest possible R
values to reduce the amount of energy used.
Why do you recommend insulation boards on a concrete base?
Insulation boards can save up to 50% on running costs because
they are a highly efficient thermal barrier to cold rising from the
subfloor. By reflecting the heat upwards into the floor instead of
losing heat to the subfloor, the floor will be warm in approximately
20 minutes after the system comes on. Without insulation boards
it could take several hours. This is important for energy efficiency
for today’s energy-conscious consumers. See the heat up chart
example on page 12 for more details.

The world’s best-selling floor heating brand

Warmup Loose Wire System
Warmup Loose Wire System uses an ultra-thin
dual-core heating wire that is flexible, easy
to install and will not raise floor levels. Ideal
for more irregular shaped areas for precise
installation.

1
2
3

5
6
4
7

1. Floor Covering
2. Flexible Adhesive
3. Warmup Loose Wire
4. Warmup Insulation Board
5. Warmup Tape
6. Flexible Adhesive
7. Subfloor

Features

Technical Data

Ultra-thin dual-core heating element
will not raise floor levels

Operating voltage: 230V: 50Hz

The thinnest dual-fluoropolymer
coated heating wire (less than 1.8mm
diameter)

Cable thickness: 1.8mm

BEAB approved heating element
meets the highest safety standards

Average output rating: 150 W/m2

Quick installation – Single connection
lead for fewer steps

Inner/Outer wire insulation:
Advanced fluoropolymer
Single 3m long ‘cold tail’ connection
lead

LIFETIME
LIMITED

WARRANTY

Approvals: BEAB
European compliant and CE marked
Lifetime Warranty & SafetyNet™
Installation Guarantee

Call us now 0845 345 2288 or visit www.warmup.co.uk

Price Guide
Heaters

Wattage

Amps

Price
(Excl 20%
VAT)

DWS300

300W

1.30A

£101.66

2.5 to 3.4m

DWS400

400W

1.80A

£120.83

3.5 to 4.4m

DWS600

600W

2.61A

£177.49

4.5 to 5.9m

DWS800

800W

3.48A

£229.16

6.0 to 6.9m

DWS600 + DWS400

1000W

4.41A

£298.32

7.0 to 8.4m

2 x DWS600

1200W

5.22A

£354.98

8.5 to 9.9m

DWS800 +DWS600

1400W

6.09A

£406.65

2 x DWS800

1600W

6.96A

£458.32

DWS800 + DWS600
+DWS400

1800W

7.89A

£527.48

2 x DWS800 +
DWS400

2000W

8.76A

£579.15

2 x DWS800 +
DWS600

2200W

9.57A

£635.81

3 x DWS800

2400W

10.43A

£687.48

2 x DWS800 +
DWS600 + DWS400

2600W

11.37A

£756.64

Area Heated
1.5 to 2.4m

10 to 11.4m

11.5 to 12.9m

13.0 to 14.4m

14.5 to 15.9m

16.0 to 17.4m

17.5 to 18.9m

19.0 to 20.4m

20.5 to 21.9m

22.0 to 25m

3 x DWS800 +
DWS400

2800W

12.24A

£808.31

3 x DWS800 +
DWS600

3000W

13.04A

£864.97

4 x DWS800

3200W

13.91A

£916.64

*Prices above DO NOT include a Warmup thermostat. (See pages 36 - 45 for details).

Installation video for Warmup Loose Wire System.
Always refer to the installation manual prior to commencing your project.

The world’s best-selling floor heating brand

Installation Guide
(Refer to installation manual for complete instructions)
Ensure the subfloor is smooth, clean and dry. We recommend you
install Warmup Insulation Boards for energy efficiency, but if you do
not, paint the floor with the Warmup primer and allow to dry. Mark
the perimeter and heater spacings on the floor using the sizing
guide at the back of the installation manual.
Laying the Loose Wire System
Tape the joint to the start point on the floor and lay out the wire
in parallel lines with U-shape returns. Tape and secure the heating
wire to the floor with the adhesive tape provided. Ensure an even
coverage with a minimum of 50mm spacing. Once completed, tape
down the entire length of the heating wire.

Connecting to the power supply
NOTE: All electrical connections must be performed by a certified
electrician.
Chisel out channels for the power supply cable and floor sensor
probe and secure with fixing tape. Wire the thermostat, following
the instructions provided.
Completing the job
Apply a full bed of flexible tile adhesive over the taped wire and tile
as normal, taking care not to damage or dislodge the heating wire.
Grout the floor as soon as possible and allow the adhesive to fully
dry before switching on the heater.
1

1. Outer Insulation: advanced fluoropolymer
2. Diameter 1.8mm
3. Earth Braid
4. Inner Insulation: advanced fluoropolymer
5. Multi-strand twin conductors heating element

Call us now 0845 345 2288 or visit www.warmup.co.uk

Frequently Asked Questions
Can I use the Warmup Loose Wire System as a primary heat
source?
If your room is well insulated and complies with modern insulation
levels you should be able to use Warmup as the sole heat source.
However, if your house is an older property with lower insulation
properties it is likely that an additional heat source may be
required. Heat loss calculations can be carried out by a builder,
architect or heating engineer.
What type of flooring can I use over the Loose Wire System?
The Loose Wire System is specifically designed for use under tiles
and natural stone. Consult the chart on page 3 - Warmup has a
range of heating systems for virtually any floor finish.
What can I do if the heater is too big for my area?
Warmup Loose Wire gives you the flexibility to alter the wire
spacing. The spacings between each run of heating element can be
brought down to a minimum of 50mm and a maximum of 100mm.
NOTE: The heating wire cannot be shortened or cut at any
stage. The correct size heater should be purchased for the floor
area to be heated (e.g. the net heated area after all fixed units have
been subtracted). If in doubt, call 0845 345 2288 and let our trained
staff advise you.
Should I use primer with the Loose Wire System?
If the heating element is being laid directly onto a plywood or
concrete subfloor, use the primer supplied. Leave to dry for 2 ~ 3
hours until tacky, then lay the heating element. If an insulated or
standard tile backer board is being used, no primer is needed. We
recommend you use Warmup Insulation Boards.
How long after installation can I turn the heaters on?
The flexible tile adhesive must be fully dried before the underfloor
heating can be turned on. Allow a minimum of 7 ~ 10 days. Turning
the system on too early can force the flexible tile adhesive to dry
too quickly, causing it to crack.

The world’s best-selling floor heating brand

NEW! NEW! NEW!

Warmup 150W & 200W/m2
StickyMat System
Warmup StickyMat underfloor heating system is
suitable for all projects: new-build, retrofits and
refurbishments. The StickyMat System consists
of a thin loose wire evenly spaced and taped to a
glassfibre mesh with pressure sensitive adhesive,
reducing installation time by 35%, for the fastest
and most secure installation method of electric
underfloor heating.

1
2
3

1. Floor Covering
2. Flexible Adhesive
3. Warmup StickyMat
4. Warmup Insulation Board
5. Flexible Adhesive
6. Subfloor

Features

4
6

Technical Data

The thinnest dual-fluoropolymer
coated heating wire (less than 1.8mm
diameter)

Operating voltage: 230V: 50Hz

StickyMat with pressure sensitive
adhesive, for the fastest and most
secure installation

Width: 500mm (0.5 metre)

Can be repositioned easily without
losing adhesion

Mat thickness: 3mm

The pressure sensitive adhesive ensures
Inner/Outer wire insulation:
that no wire or mesh is raised when
tiling or covering with a self-levelling
advanced fluoropolymer
compound
Output rating: 150W/m2 and 200W/m2

LIFETIME
LIMITED

WARRANTY

Single 3m long ‘cold tail’ connection
lead
Approvals: BEAB
European compliant and CE marked
Lifetime Warranty & SafetyNet™
Installation Guarantee

Call us now 0845 345 2288 or visit www.warmup.co.uk

Price Guide
Price Guide for 150W/m2 Underfloor Heating StickyMat
Area Heated
1m

150W

0.65A

£ 82.25

225W

0.98A

£ 104.12

SPM2

300W

1.30A

£ 118.11

SPM2.5

375W

1.63A

£ 145.00

SPM3

450W

1.96A

£ 167.99

SPM3.5

525W

2.28A

£ 189.00

SPM4

600W

2.61A

£ 209.12

SPM4.5

675W

2.93A

£ 230.00
£ 254.61

2.5m
2

3.5m
2

SPM5

750W

3.26A

SPM6

900W

3.91A

£ 300.12

SPM7

1050W

4.57A

£ 345.62

SPM8

1200W

5.22A

£ 377.12

SPM9

1350W

5.87A

£ 409.49

SPM10

1500W

6.52A

£ 440.99

SPM11

1650W

7.17A

£ 468.12

SPM12

1800W

7.83A

£ 510.00

SPM15

2250W

9.78A

£ 641.37

5m
6m

7m
8m

Price
(Excl 20% VAT)

SPM1

4.5m

Wattage Amps

SPM1.5

1.5m

Heaters

10m
11m

12m
15m

*Prices above DO NOT include a Warmup thermostat. (See pages 36 - 45 for details).

Price Guide for 200W/m2 Underfloor Heating StickyMat
Area Heated

Price
(Excl 20% VAT)

Heaters

Wattage

Amps

2SPM0.5

100W

0.44A

£ 54.24

2SPM1

200W

0.87A

£ 90.99

2SPM1.5

300W

1.30A

£ 113.75

2SPM2

400W

1.74A

£ 126.87

2SPM2.5

500W

2.17A

£ 155.00

2SPM3

600W

2.61A

£ 182.00

2SPM3.5

700W

3.04A

£ 205.00

2SPM4

800W

3.48A

£ 227.49

2SPM4.5

900W

3.91A

£ 247.50

2SPM5

1000W

4.35A

£ 272.99

2SPM6

1200W

5.22A

£ 322.86

2SPM7

1400W

6.09A

£ 372.74

2SPM8

1600W

6.96A

£ 409.49

2SPM9

1800W

7.83A

£ 440.99

2SPM10

2000W

8.70A

£ 472.49

0.5m

1.5m
2m

2.5m
3m

3.5m
4m

4.5m

10m

*Prices above DO NOT include a Warmup thermostat. (See pages 36 - 45 for details).

The world’s best-selling floor heating brand

Installation Guide
(Refer to installation manual for complete instructions)
Make a floor plan of your floor area by measuring your room and
then subtract any fixtures (such as baths and cupboards). Ensure
you have the correct size mat for your floor area.
Laying the Matting System
Roll out the mesh, wire face up. At the end of the run, cut the mat
(not the wire), turn the mat through 90º or 180º and continue
laying the mat. When the area is covered, adjust the mats until the
loops are of equal distance apart. Affix the mat to the floor using
its self-adhesive mesh, or using the double sided tape on the mat.
Lay the temperature probe from the thermostat at equal distance
between two of the cable loops and attach to the floor surface.
Connecting to the power supply
NOTE: All electrical connections must be performed by a certified
electrician.
Install an RCD fused spur to power the thermostat and the matting
system heating element network.
Take the unheated power supply cable from the end of the matting
system, which should be positioned near the thermostat. Make
sure all the connections have been made to the power supply. Turn
the heater(s) on to ensure they are heating up (no more than 10
minutes).
Completing the job
Either lay a thin, self-levelling screed over the mat and leave it to
dry before laying tiles or trowel a full bed of flexible tile adhesive
directly over the mat and lay the floor tiles.
MAT: with pressure sensitive adhesive
Fastest and most secure installation
Use less self-levelling compound and
tile adhesive
Can be repositioned easily without
losing adhesion

1
1. Glassfibre Mesh with pressure sensitive adhesive
2. Outer Insulation: advanced fluoropolymer
3. Earth Braid
4. Inner Insulation: advanced fluoropolymer
5. Heating Element Strand

Call us now 0845 345 2288 or visit www.warmup.co.uk

Frequently Asked Questions
Can I use the Warmup StickyMat System as a primary heat
source?
If your room is well insulated and complies with modern insulation
levels you should be able to use Warmup as the sole heat source.
However if your house is an older property with low insulation
properties it is likely that an additional heat source may be
required. Heat loss calculations can be carried out by a builder,
architect or heating engineer.
What type of flooring can I use over the StickyMat System?
The StickyMat System is specifically designed for use under tiles
and natural stone. For other floor finishes please see our full range
of products on page 3. If you wish to use other floor coverings
please contact our Technical Team on 0845 345 2288.
Can the StickyMat System be cut?
In order to fit the mat into a specific area, it may be necessary to
cut and turn the glassfibre mesh. Care must be taken not to cut
or damage the heating wire. The heating wire / heating mat
cannot be shortened – the correct size heater must be installed on
available floor space.
Can the floor probe / power supply cables be extended?
Both these wires can be extended up to 50 metres – please consult
a qualified electrician for advice on extending the cable.
How long must I wait after installation before turning the
system on?
The underfloor heating cannot be turned on until the flexible
tile adhesive is fully dried. Please allow a minimum of 7 - 10 days.
Turning the system on too early can force the flexible tile adhesive
to dry too quickly, causing it to crack.

Installation video for Warmup StickyMat System.
Always refer to the installation manual prior to commencing your project.

The world’s best-selling floor heating brand

Warmup Inscreed Cable System
Warmup Inscreed Cable System is excellent for
installation within screeded floors of any size.
Once installed, the heated screed can be covered
with any flooring.
Option 1:
Wire laid directly
on insulation*
For use where the
concrete base is
thicker than 100mm
or uninsulated

2
3
4
1. Floor Covering
2. Screed (min 50mm)
3. Inscreed Heater
4. Metal Fixing Bands
5. Insulation*
6. Subfloor

5
6

If the concrete slab is more
or equal to 100mm and
insulated, you must install
insulation before laying the
heater.

Option 2:
Wire laid directly
on concrete slab
For use where the
concrete base is less
than 100mm thick or
insulated

2
3

1. Floor Covering
2. Screed (min 50mm)
3. Inscreed Heater
4. Metal Fixing Bands
5. Concrete Slab
6. Insulation*
7. Subfloor

If the concrete slab is more
or equal to 100mm and
insulated, you must install
insulation before laying the
heater.
* Insulation must be either foil faced or concrete faced and
suitable for use with electric underfloor heating

Call us now 0845 345 2288 or visit www.warmup.co.uk

Features

Technical Data

Tough – 6mm thick heating cable is
protected by multiple layers of metal
shielding and insulation

Operating voltage: 230V: 50Hz

Floor covering can be changed
without risk of damage to the heater

Output rating: 100 to 210W/m²

Heating element meets the highest
safety standards

Single 2.5m long ‘cold tail’
connection lead

Grounding braid makes it safe for wet
rooms

European compliant and CE marked

Versatile - compatible with all floor
finishes

10-Year Warranty & SafetyNet™
Installation Guarantee

Suitable for new-build

Price Guide
Coverage
at
100W/m2

1.8m

0.9m

1.4m

2.0m

2.5m

3.3m

3.8m

5.0m

6.0m

7.3m

1.9m

2.6m

3.3m

4.3m

5.1m

3.9m
5.0m
6.5m

10.0m

6.7m

8.0m

9.7m

12.0m
14.6m

Coverage
at
210W/m2

1.2m

2.8m

7.6m

Coverage
at
150W/m2

Heaters

Price

Heater
Length

Wattage

Amps

(Excl
20% VAT)

WIS180

9.0

180W

0.8A

£43.33

WIS280

14.0

280W

1.2A

£60.83

WIS390

19.5

390W

1.7A

£69.16

WIS500

25.0

500W

2.2A

£82.49

WIS650

32.5

650W

2.8A

£99.16

WIS760

38.0

760W

3.3A

£104.16

WIS1000

50.0

1000W

4.3A

£125.83

WIS1200

60.0

1200W

5.2A

£147.49

WIS1460

73.0

1460W

6.3A

£173.33

WIS1550

77.5

1550W

6.7A

£177.49

WIS1770

88.5

1770W

7.7A

£190.83
£207.49

10.3m

7.8m

11.8m

8.9m

20.7m

13.8m

10.4m

WIS2070

103.5

2070W

9.0A

26.0m

17.3m

13.0m

WIS2600

130.0

2600W

11.3A

£250.83

20.9m

15.7m

WIS3140

157.0

3140W

13.7A

£289.99

22.5m

16.9m

WIS3370

168.5

3370W

14.7A

£307.49

15.5m

17.7m

31.4m
33.7m

*Prices above DO NOT include a Warmup thermostat. (See pages 36 - 45 for details).

Accessories

Price (Excl 20% VAT)

Metal Fixing Bands - 25m

£41.00

Fixing Tape - 50m

£8.33

For more information about this product and
installation videos scan the code.
Always refer to the installation manual prior to
commencing your project.

The world’s best-selling floor heating brand

Installation Guide
(Refer to installation manual for
complete instructions)
Draw up a floor plan to determine the
placement of the thermostat, heating
cable and the sensor probe.
Laying the Inscreed Cable System
The metal fixing strips should be laid out perpendicular to the
heating element runs. Secure these fixing strips on the insulation or
concrete floor using fixing nails or adhesive.
The fixing strips should be evenly spread across the floor at
intervals of 0.75 meters and placed so as to leave a 100mm border
all the way around the room.
The heating cables should then be laid up and down the room and
clipped into the fixing strip. Please check the sizing guide at the
back of the installation manual to determine the cable spacing. To
ensure an evenly heated floor, the cables should be spaced evenly
at all times.
2
4

1. Outer Insulation: PVC
2. Diameter 6mm
3. Earth Braid
4. Inner Insulation: advanced fluoropolymer
5. Heating Element Strand

Connecting to the power supply
The heating cable cold tail should be connected to the thermostat
by a certified electrician. The heating cables should be tested again
BEFORE screeding.
Completing the job
Once laid, the heating cables must be covered with a minimum
thickness of 50mm screed.
Install the Warmup thermostat and floor probe in one of the
following ways:
1. Placed directly in the top 10mm of screed covering the heating wire
2. Placed into a channel cut out of the surface of the screed
3. Placed in a flexible conduit in the top 10mm of screed

Call us now 0845 345 2288 or visit www.warmup.co.uk

Frequently Asked Questions
Can the Inscreed Cable System be shortened?
Never shorten the Inscreed Cable. You must ensure that the
correct size is installed into the area. We have a large range of sizes
to choose from.
How thick is the screed used with the system?
The Warmup Inscreed Cable is designed to be placed within a
screed of at least 50mm in thickness. The exact floor build up
depends on the insulation materials in the subfloor - please see the
installation manual for full details.
Can the Inscreed Cable System be laid directly onto insulation
material? (i.e. single pour)
Yes, if you use cement-faced or foil-faced insulation boards suitable
for electric underfloor heating such as the Warmup Insulation
Boards.
When can I turn my heating on?
The heating should not be activated until the screed has fully cured
(approximately 7-28 days).
Where should I place the floor probe?
The floor probe should be located at the surface of the screed
layer below the floor covering (top 10mm of screed). It can also be
cemented into a channel cut out of the surface of the screed.

The world’s best-selling floor heating brand

Warmup Foil Heater System
The Warmup Foil Heater is a streamlined electric
radiant floor heater designed for use with
carpet, vinyl, wood and other floating floors.
We recommend using the Warmup Insulated
Underlay and Dual Overlay Systems (See pages
30 - 33) for maximum efficiency.* Warmup has
successfully completed controlled tests with
Amtico and Karndean flooring.
*excludes bathrooms; cannot steam clean carpets

Contact
Warmup
to receive our
technical guide
for wood
floors

2
3

1. Floor Covering
2. Warmup Foil Heater
3. Insulated Underlay
4. Subfloor

Features
Installed directly under floor finish;
no self-levelling required
Fully earthed flat aluminium foil will
not raise floor levels
Wire based system can be adapted to
fit around objects
Great for heating under floating floors
such as laminate and hardwood

Technical Data
Construction: Wire with advanced
fluoropolymer insulation, encased in
aluminium foil
Operating voltage: 230V: 50Hz
Output rating: 140W/m2
Mat width: 0.5m
Mat length: min 3m, max 24m
Heating cable spacing: 50mm

15 YEAR
LIMITED

WARRANTY

Cold lead length: 3m
Approvals: BEAB
European compliant and CE marked
15-Year Warranty & SafetyNet™
Installation Guarantee

NOTE: MUST be used with the Warmup Insulated Underlay (See pages 30 - 31).
NOTE: Must be used with Warmup Dual Overlay (See pages 32 - 33) when laying vinyl or carpet.
NOTE: Always check compatibility of flooring with electric underfloor heating.

Call us now 0845 345 2288 or visit www.warmup.co.uk

Price Guide
Area Heated

Heaters

Wattage

Amps

Price
(Excl 20% VAT)

WLFH-140W/140

140W

0.61A

£60.83

1.5

WLFH-140W/210

210W

0.91A

£73.33

WLFH-140W/280

280W

1.22A

£91.66

WLFH-140W/420

420W

1.83A

£138.33

WLFH-140W/560

560W

2.43A

£173.33

WLFH-140W/700

700W

3.04A

£212.49

WLFH-140W/840

840W

3.65A

£250.83

WLFH-140W/980

980W

4.26A

£289.99

WLFH-140W/1120

1120W

4.87A

£329.16

WLFH-140W/1260

1260W

5.48A

£372.49

WLFH-140W/1400

1400W

6.09A

£411.66

WLFH-140W/1680

1680W

7.30A

£493.33

* Prices above DO NOT include a Warmup thermostat. (See pages 36 - 45 for details).
MUST be used with the Warmup Insulated Underlay (See pages 30 - 31). If you are laying a vinyl
or carpet (excludes bathrooms) the Warmup Dual Overlay MUST be used (See pages 32 - 33).
A maximum of 25m² of heating can be used with one thermostat.

For more information about this product and
Installation videos scan the code.
Always refer to the installation manual prior to
commencing your project.

Installation Guide
(Refer to installation manual for complete instructions)
Warmup’s foil heating mats are available in several convenient
sizes. Use larger mats as much as possible and smaller mats as gap
fillers. Ideally, the combination should cover 80% of your floor area.
Exclude permanent or static fixtures from your calculations.
Laying the Foil Heater System
Lay the heating mats on top of the insulation, leaving a gap of
around 50mm from the wall to the heating mats and a gap of about
10mm between each mat. Stretch and secure the mats to the floor
with the aluminium tape provided. Additional duct tape can be
used where required.
Place the mat’s electrical supply cables towards the junction box,
ensuring they do not cross each other. Create a slight groove in the
insulation under the joint to ensure that the heating mat lays flat.

The world’s best-selling floor heating brand

Connecting to the power supply
NOTE: All electrical connections must be performed by a certified
electrician.
Completing the job
Create a groove in the subfloor to accommodate the floor probe.
Connect the floor temperature sensor to the thermostat through
a conduit and install between two heating wire runs on the mat.
The probe wire must NEVER touch or be crossed by the heating
element.

Frequently Asked Questions
What types of flooring can be used?
The Foil Heaters can be used under carpet, vinyl, wood or floating
floorings provided they are no thicker than 18mm and can
withstand up to 27oC of heat. Check with the manufacturer to
ensure it is suitable for use with electric underfloor heating.
Can the Foil Heaters be cut and turned?
You can cut and turn the foil casing to suit the shape of the room,
but NEVER cut the wire. Once the aluminium foil has been cut
and the mat has been re-positioned, use the aluminium foil tape
provided to cover any exposed wire and link the two pieces of the
mat. Please see the installation manual for full details and diagrams.
When can I turn my Foil System on?
Once the finished floor has been laid, wired up and tested, the
system can be switched on immediately.
Which insulation materials should be used?
We recommend Warmup’s own brand Insulation Underlay be used
with Warmup Foil Heaters. If you are installing a soft flooring such
as vinyl or carpet, use the Warmup Dual Overlay to protect the foil
heating wire from heels and heavy load points.

1. Aluminium Foil Earth
2. Wire Insulation: advanced fluoropolymer
3. Multi-strand twin conductors heating element

Call us now 0845 345 2288 or visit www.warmup.co.uk

View or Download our specialist
Wood Guide at
www.warmup.co.uk or call
0845 345 2288 to receive a copy

The world’s best-selling floor heating brand

Warmup Insulated Underlay
Warmup Insulated Underlay is a thin
polystyrene insulation barrier with effective
acoustic properties to reduce contact noise. It
sits between the cold subfloor and Warmup’s
Foil Heater, reflecting heat upwards, making
the heating system even more efficient. The foil
backing acts as a moisture barrier.

1. Floor Covering
2. Warmup Foil Heater
3. Warmup Insulated Underlay
4. Subfloor

Scan the code for more information
about this product.
Always refer to the installation manual
prior to commencing your project.

Features

Technical Data

Resists heat loss and increases the
heating systems efficiency

Roll Size:
1200mm (W); 2.5sqm, 5sqm,
10sqm and 25sqm

Extremely effective for reducing
contact noise

Thickness:
6mm

Very thin at only 6mm in depth

Composition:
Top Layer: Grooved polystyrene
Bottom layer: Silver foil with
adhesive overlap

Lightweight and easy to install

R Value:
0.19 m²K/W

Foil backing acts as a moisture barrier

Contact sound reduction: 25dB
∆Lw when used in conjunction with
the Warmup Dual Overlay System.

Recommended for use with the Warmup Dual Overlay System

Call us now 0845 345 2288 or visit www.warmup.co.uk

Price Guide
Area Covered

Insulated Underlay
System Code

Price (Excl 20% VAT)

2.5m

WIU2.5

£24.98

5.0m2

WIU5.0

£47.49

10.0m2

WIU10.0

£91.66

25.0m2

WIU25.0

£216.66

In the case of floating substrate systems the sound reduction of the finished floor covering will
always depend on the impact sound reduction of the existing substrate.

Installation Guide
(Refer to installation manual for complete instructions)
Install the Insulation Underlay with the silver foil facing down onto
a clean and dry floor. After fitting the first row, roll the next section
of underlay. Remove the protective film from the self-adhesive
overlap and stick both rows together, creating a damp proof barrier.
Stagger subsequent rows until the whole floor area is covered.

Frequently Asked Questions
What is it made from?
The top layer of the underlay is comprised of a 6mm grooved
lightweight polystyrene (which offers added acoustic properties
by reducing contact noise) and a bottom layer of silver foil which
has an adhesive overlap to join subsequent rolls. The underlay has
a sound reduction of 25dB ΔLw when used in conjunction with
Warmup Dual Overlay (See pages 32 - 33). In the case of floating
substrate systems, the sound reduction of the finished floor
covering will always depend on the impact sound reduction of the
existing substrate.
What is an R Value?
The R value is a measure of thermal resistance used in the
construction industry. A rating of 0.19 represents a low level of
insulation for energy efficiency.
Can I use this under tiles and stone?
No. It is designed for installation with the Foil Heater when installed
under soft and resilient floor coverings such as wood, carpet, vinyl
and linoleum. When your finish needs to be fixed down (glued)
such as carpet, then a combination of the Insulated Underlay,
Foil Heater and Dual Overlay should be used. Warmup’s Insulated
Underlay has been specially developed as part of a complete stable
overlay system with the Dual Overlay to protect the heating wire
from sharp heels and heavy point loads. The combined thickness
of the Warmup Dual Overlay and the Warmup Insulated Underlay is
13mm.

The world’s best-selling floor heating brand

Warmup Dual Overlay
Warmup Dual Overlay is a free-floating subfloor,
offering a smooth and seamless finish for carpet, vinyl
and linoleum. The two layers protect the heating wire
from sharp or heavy point loads and provides even
heat distribution. Installation is dry, clean and quick.
Both the Insulated Underlay and Dual Overlay are
designed to work together with Warmup Foil Heaters
(See pages 26 - 33).

1. Floor Covering
2. Warmup Dual Overlay-Top
3. Warmup Dual Overlay-Base Board
4. Warmup Foil Heater
5. Warmup Insulated Underlay
6. Subfloor

2
3
4

Features

Technical Data

Consists of a base board (3mm deep)
and top board (4mm deep) with a
contact adhesive to bond them
together

Contents:
4 base and 4 top boards (covers
2.88m²)

Provides a stable subfloor on which a
variety of floor coverings can be laid

Size:
1200mm (W) x 600mm (L)

Very thin at only 7mm in depth

Thickness:
Base board - 3mm
Top board - 4mm

Protects electric heating wire from
damage if flooring is not laid
immediately

Composition:
MDF fitted with an interactive
adhesive

Installation is quick, easy and dry - no
need for self-levelling

Density (kg/m³): 770

Provides even heat distribution

Bending strength kg/cm²: >40
Humidity (%): 4-10

NOTE: Always check compatibility of flooring
with electric underfloor heating.

Thermal R value (m²K/W): 0.047
Fire Class, DIN4102: B2

Call us now 0845 345 2288 or visit www.warmup.co.uk

Price Guide
Price (Excl 20% VAT)
WDO - Dual Overlay System (covers 2.88m2)

£69.16/pk

Scan the code for more information
about this product.
Always refer to the installation manual
prior to commencing your project.

Installation Guide
(Refer to installation manual for complete instructions)
The Warmup Dual Overlay is comprised of a 3mm deep base board
and 4mm deep top board. The bottom and top layers are laid out
with staggered joints and arranged so that the top boards overlap
the joints in the base boards. The Warmup Foil Heating System lays
between the Underlay and Dual Overlay System. This method of
installation provides a stable surface for the floor finish to rest on
and avoid any joints showing through the final floor finish. Finally,
the floor finish can either be glued to the boards as a final layer or
simply laid freely upon them.

Frequently Asked Questions
Is the Dual Overlay fixed to the subfloor?
The Warmup Dual Overlay is a floating subfloor - it is not fixed to
the floor below. It is comprised of a 3mm deep base board and a
4mm deep top board. Both boards have contact adhesive, bonding
them together to make one solid subfloor, to which a variety of
floor coverings may be fixed. It provides a smooth and seamless
subfloor making it suitable for soft and resilient floor coverings
such as carpet, vinyl and linoleum. The combined thickness of the
Underlay and Dual Overlay is 13mm.
How is it sold?
Each pack contains: 4 base boards & 4 top boards and covers
2.88m² of flooring.
Can I use other Warmup Heaters with the Underlay/ Dual
Overlay?
The Warmup Underlay / Dual Overlay systems are designed to work
specifically with Warmup Foil Heaters only.
Please Note:
* Cannot be used in wet areas such as bathrooms.
**It is strongly recommended to dry clean carpet flooring laid on
Dual Overlay. Do not steam clean, as this can cause moisture to get
into the wood and joints and show through the flooring over time.

The world’s best-selling floor heating brand

NEW! NEW! NEW!

150W & 200W/m2 Electric In-Wall
Heating Panel
In-Wall Heating Panels are perfect if you wish to
extend the luxury of the floor heating to the walls,
ideal if you wish to heat a small area of the wall or
for whole room heating; this is particularly suitable
in dwellings where heat loss and poor insulation is
an issue.
The In-Wall Heater Panels, suitable for use behind
tiles or natural stone are available in two wattages,
150W/m2 & 200W/m2, offering you a choice to
add additional heat with the 200W/m² which is
particularly suitable for high heat loss rooms.
For more information on the application of the
In-Wall Heater Panels or to receive a quotation
please contact our Projects Division on 0845 034
8270 or visit our website www.warmup.co.uk

Features

Technical Data

The thinnest dual-fluoropolymer coated
heating wire (less than 1.8mm diameter)

Operating Voltage: 230V: 50Hz

Toughest wire - multi-strand core,
double-insulated using advanced
fluoropolymers (ECTFE).

Width: 500mm (0.5 metre)

Sturdy glassfibre mesh for extra
durability.

IP Rating: IPX7

High quality double-sided tape, for easier
installation.

Output Rating:
150W/m² and 200W/m²
Protection Class: I
CE Marked
Lifetime Warranty and SafetyNet™
Installation Guarantee

Scan the code for more
information about this
product.
Always refer to the
installation manual prior to
commencing your project.

Call us now 0845 345 2288 or visit www.warmup.co.uk

The world’s best-selling floor heating brand

4iE

SMART WIFI
THERMOSTAT

NEW! NEW! NEW!

For central and underfloor heating

The right temperature. The best tariff.
Effortlessly.
High quality design and dependable engineering,
personalised for you
The 4iE is designed to look great in contemporary and traditionally
styled homes. Available in Onyx Black and Bright Porcelain, with
angled chrome edges to reflect wall colours.
Personalise your 4iE with custom photo backgrounds and a range
of textured skins including brushed metal and natural wood
effects. Use the large display to check the weather forecast and
traffic delays for your journey before you leave home.

*Visit www.warmup.co.uk for more details
36

Call us now 0845 345 2288 or visit www.warmup.co.uk

By working with families across
Europe and our research facilities
in Germany and the UK during
the last 20 years, we have found
the most efficient ways to control
heating in real homes.

Always at the right temperature, home or away
The 4iE does not require programming, it works with your
smartphone to ensure your home is always at the temperature
you want, just as you arrive and using more efficient
temperatures when you’re away.
If you want to use a conventional program or just want to make
a quick change, the MyWarmup app is simple and easy to use.

The most efficient settings for your home
The 4iE learns how you use your heating and the unique way
your home responds to changes in temperature to calculate
more efficient settings.
You will get tips with advice on comfortable temperatures that
use less energy and the optimal times to turn the heating off
early and still stay warm, saving up to 25% on your heating use.

Automatically on the best energy tariff, year after year
The 4iE can find you lower energy tariffs and automatically
switch to the best deal. According to the Department of Energy
& Climate Change, switching energy tariff can save on average
£210 per year.
You can choose to let the 4iE switch for you automatically when
a better deal is available or see the results and easily switch
yourself.

3 YEAR

LIMITED

WARRANTY

*Visit www.warmup.co.uk for more details

The world’s best-selling floor heating brand

Easy to install and set up
Two piece design and wireless
software updates to reduce
call-backs
Easy to setup WiFi
Free installer training classes
Self guiding screw terminals
prevent driver skipping

The 4iE uses a standard 35mm deep back box to house
connections behind its stylish facia. It is installed just like a
traditional three-wire thermostat and therefore easily replaces
existing controls – including covering fixing holes from old
thermostats without the need for additional plates.
Technical Data
Dimensions: (H/W/D): 90 x 120 x 18mm (from wall)
Sensors: Air and floor/ambient
Installation depth: 35mm back box
IP rating: IP33
3-Year Warranty with option to upgrade to Lifetime Warranty
Approvals: BEAB
CE Marked and European compliant
Sensor Type: NTC 10K 3m Long (can be extended to 50m)
Size of Display: 3.5”
Compatibility: Ideal for Electric and Hydronic underfloor heating up to 16A.
Combi and System boilers with switch live (230VAC) input
Er-P Class: IV

Code

Description

Price (Excl. 20%
VAT)

4iE™ OB

Onyx Black Smart WiFi Thermostat

£166.66

4iE™ BP

Bright Porcelain Smart WiFi Thermostat

£166.66

Call us now 0845 345 2288 or visit www.warmup.co.uk

Frequently Asked Questions
How do I connect the 4iE to my internet?
The 4iE connects to WiFi just like a smartphone or laptop.
Simply find your WiFi network in the 4iE menu and enter your
password using the onscreen keyboard.
Once connected you need to create your MyWarmup account.
Go to my.warmup.com and register. From there you can add the
4iE to your account using the unique code displayed on the 4iE.
Which heating systems can the 4iE control?
The 4iE can control Warmup’s electric and hydronic underfloor
heating as well as central heating (combi and system boilers).
Central heating and hydronic underfloor heating systems are
controlled using a ‘switch live’ wire.
Warmup recommends that you check with your heating
system manufacturer or installer to find out if your system can
be controlled by a ‘switch live’ wire. The 4iE should always be
installed by a certified professional.
Data Protection
MyWarmup uses the same web security as online banking
and each communication between your 4iE and MyWarmup is
protected using the same encryption the intelligence services
use for classified documents.
Warmup backs-up and stores all data safely encrypted to
protect it, with firewalls and electronic surveillance in place.
To ensure your system is safe, Warmup recommends your WiFi
network is password protected and you do not share your
log-in details with anyone. Warmup will never ask you for your
password.

View the installation video for the Warmup 4iE Smart WiFi Thermostat
Always refer to the installation manual prior to commencing your project.

The world’s best-selling floor heating brand

Warmup 3iE™ Energy-Monitor
Thermostat
Designed by Warmup, the unique and exclusive
3iE™ Energy-Monitor Thermostat was the first
programmable thermostat to come with Active
Energy Management™ prompting users to save
up to 10% on energy bills.

Features

Technical Data

Active Energy Management™
prompts users to save up to 10% on
utility bills

Output relay: 16A, 3,600W

Easy-to-use interface eliminates
complicated manuals

Temperature range: 0 / +50 °C

Unrivalled accurate floor temperature
control of +/- 0.5°C, significantly
reduces energy wastage

Programming function: 10 events
and 10 temperatures / day

10 programmable periods per day
for efficient energy use

Sensor type: NTC, 3m long

Designed and available exclusively
from Warmup

Dimensions: (H/W/D):
90mm x 113mm x 19mm (flush fit)

Graphs show exact heating costs for
underfloor heating

Size of display: 2.4”

Stylish colours to suit any decor

Installation depth: 30mm
IP rating: IP20/IP32 (with optional
gasket)

3 YEAR
LIMITED

WARRANTY

Approvals: BEAB
European compliant and CE marked
3-Year Warranty with option to
upgrade to Lifetime Warranty
Er-P Class: IV

Call us now 0845 345 2288 or visit www.warmup.co.uk

Price Guide
Description

Price (Excl 20%
VAT)

3iE™ PB

Piano Black Programmable Thermostat

£120.83

3iE™ CC

Classic Cream Programmable Thermostat

£120.83

3iE™ SG

Silver Grey Programmable Thermostat

£129.99

3iE™ LG

Leaf Green Programmable Thermostat

£129.99

3iE™ MB

Madison Blue Programmable Thermostat

£129.99

3iE™ DP

Deep Pink Programmable Thermostat

£129.99

3iE™ WB

Warm Berry Programmable Thermostat

£129.99

Code

The world’s first fully interactive, touch technology,
energy-monitor thermostat features an easy-to-use interface,
eliminating complicated instruction manuals. The display shows
recorded energy consumption usage, so that users know the exact
underfloor heating costs. Up to 10 programmable periods can be
set each day to maximise energy efficiency.
Innovative
First thermostat with a 2.4” full colour screen and integrated touch
technology - patents pending.
Beautifully crafted fashion colour fascias with chrome edging are
perfectly in tune with the modern home environment.
Interactive
Clear graphical display makes any adjustment quick and easy.
Choose the display style that suits you best – wide choice of screen
themes.

Installation video for Warmup 3iE energy-monitor thermostat.
Always refer to the installation manual prior to commencing your project.

The world’s best-selling floor heating brand

Intelligent
Proportional Adaptive Function ensures the room does not
over-heat, reducing wasted energy whilst also protecting the
components inside. The Early Start algorithm learns how long it
takes to warm the room and activates the heating so it’s up to
temperature at the right time.

Energy Efficient
Unrivalled accurate floor temperature control means no wasted
energy - reducing the costs associated with over-heating.
Graphical energy monitor shows exactly how much energy is being
used and when.
AEM™ prompts you to choose the best and most efficient
temperature for each room, maximising energy efficiency.

Installation
The 3iE™ Energy-Monitor Thermostat should be installed by a
certified electrician only, using Warmup’s installation instructions.

Call us now 0845 345 2288 or visit www.warmup.co.uk

Frequently Asked Questions
What is Active Energy Management?
The 3iE Energy-Monitor Thermostat has a unique feature called
Active Energy Management. It displays graphs of the users
recorded energy consumption. By following the on-screen
prompts, users can save up to 10% on utility bills by choosing the
best and most efficient temperature for each room.
How many sensor settings does the 3iE have?
Warmup’s 3iE offers a choice of three (3) sensor settings: air,
external and floor.
This provides unrivalled accurate floor temperature control to
maximise energy efficiency.
Can more than one heater be controlled via the same
thermostat?
Yes. Each thermostat can take up to 16 amps – please note that
the heaters should be wired in parallel only at the thermostat
or junction box. A maximum of two (2) heaters can be wired
directly into the back of the thermostat. If more than two (2)
heaters are used (combined load of less than 16 amps) they must
be wired into a junction box, which connects to the thermostat.
For more than 16 amps a contactor and an RC unit are used in the
circuit. Please consult a certified electrician or Warmup’s Technical
Team on: 0845 345 2288 for advice on this type of installation.

The world’s best-selling floor heating brand

Tempo Digital Programmable
Thermostat
The Tempo thermostat enables end users to
choose the time as easily as they would with a
watch or clock and quickly set their programs
– heat on when they want it and off when they
don’t need it.

Porcelain White

Piano Black

Features

Technical Data

Stylish and contemporary design

Input voltage: 230V +/- 15% at 50Hz

Clear screen displaying program
details

Max output: 16A

Easy control with dial and sliders

Dimensions: (H/W/D):
90 x 113 x 23mm (flush fit)

Suitable with all Warmup electric and
hydronic underfloor heating systems

Screen size: 45 x 50mm

Available in Porcelain White and
Piano Black

Sensors: Floor/air

Perfect for the whole house with the
exception of the bathroom

Programming: 7-day, 1 day, 5/2 day
Battery backup: 3 months (CR2032
battery provided)
IP rating: IP20

3 YEAR
LIMITED

WARRANTY

Approvals: BEAB
European compliant and CE marked
3-Year Warranty with option to
upgrade to Lifetime Warranty
Er-P Class: IV

Also available
MSTAT Manual
Thermostat
Suitable with
Warmup’s electric
underfloor heating
systems only

RCD/Fused Spur
30mA
Residual Current
Device
Fused Spur

Call us now 0845 345 2288 or visit www.warmup.co.uk

Price Guide
Programmable Thermostat

Price (Excl 20% VAT)

Tempo - Piano Black Programmable
Thermostat

£83.33

Tempo - Porcelain White Programmable
Thermostat

£83.33

Manual Thermostats

Price (Excl 20% VAT)

MSTAT - White Manual Thermostat

£60.83

Accessories

Price (Excl 20% VAT)

RCD/Fused Spur - 30mA Residual Current
Device

£41.66

Tempo in each zone provides the following:
BETTER easy-to-use interface and intuitive design
FASTER set-up takes just minutes to get right the first time
SMARTER control of energy costs
With Tempo, end users can simply program their settings to suit
individual requirements, warmer when they are at home, lower
when they are away or asleep.
It will help avoid wasting energy and achieve savings on utility bills.
Its Proportional Adaptive Function ensures the room does not
over-heat, reducing wasted energy whilst also protecting the
components inside. The Early Start algorithm learns how long it
takes to warm the room and activates the heating so it’s up to
temperature at the right time.

Frequently Asked Questions
What is the difference between Tempo and the 3iE
Energy-Monitor Thermostat?
The main difference is the 3iE’s energy-monitoring function. The
monitor tracks your exact usage and based on your fuel rates,
displays your underfloor heating costs. Through the Active Energy
Management, it gives users suggestions to lower usage and fuel
costs without sacrificing comfort.
How does it work?
The sliding lever on the right-hand side takes you through the four
(4) easy program steps to set the day, time and heat periods you
desire. Turn the dial to increase or decrease the settings and then
press to secure that setting. The sliding lever at the bottom allows
you to select between manual, automatic, frost-protection or off
modes.

The world’s best-selling floor heating brand

Mirror Demisters
Mirrors are revealing while they brighten the
most ordinary bathroom. However, steamed up
bathroom mirrors can present a challenge to
homeowners. Not any longer, thanks to Warmup
Mirror Demisters - a safe and easy way to remove
steam from bathroom mirrors.

Features

Technical Data

Flat film does not take up space

IP57 Rated

Self-adhesive for convenient
installation directly onto the back
of the mirror

Suitable for zones 1 & 2 according
to BS7671:2012

Resistant to moisture, vibration,
shock, dust and ageing

Operating voltage: 230V: 50Hz

Connects to existing room light
circuit for automatic operation
when light is switched on

1m cold tail

Suitable with most types of
mirrors, existing or newly installed

Double insulated

Can be used in combination for
large mirrors

No transformers or thermostats
necessary
European compliant and CE marked
1-Year Warranty

Call us now 0845 345 2288 or visit www.warmup.co.uk

Price Guide
Size & Description
WMD1 - 400mm x 450mm

Wattage

Price (Excl 20% VAT)

18W

£47.49

WMD2 - 600mm circular

55W

£64.99

WMD3 - 290mm x 290mm

27W

£34.99

WMD4 - 600mm x 1100mm

132W

£90.83

Installation Guide
(Refer to installation manual for complete instructions)
The Mirror Demisters are self-adhesive and must be mounted
directly onto the reverse side of the mirror or onto a sound surface
which is in direct contact with the mirror. No other adhesives
should be used.
The Mirror Demisters should be connected by a certified electrician.
Scan the code for more information
about this product.
Always refer to the installation manual
prior to commencing your project.

Frequently Asked Questions
Do the Mirror Demisters come in different sizes?
The Mirror Demisters come in round, square and rectangular sizes.
Installation is as simple as exposing the self-adhesive backing and
sticking directly onto the back of the mirror.
What if my mirror is a different size?
The Demisters can be combined for larger mirrors. However, you
must leave a minimum of 5mm between each Demister.
You must also leave a minimum of 10mm around the edges to
ensure the Demisters fit.
How safe are they in the bathroom?
The Mirror Demisters have an IP57 rating and are suitable for zones
1 and 2 according to BS7671:2012, making them safe for bathrooms.
The Demister can either be connected directly to a switched light
circuit, designed to activate the Demister when the light is switched
on or via a separate switch connected to the main lighting circuit.

The world’s best-selling floor heating brand

Electric Towel Rails
When it comes to luxury, nothing beats the comfort
of a soft, warm towel. Warmup heated Towel Rails
not only bring comfort, they also help to heat a
bathroom.
Committed to innovation, whilst at the same time
being energy efficient, Warmup’s range of traditional
and contemporary Towel Rails offer a solution to
cater for all preferences, lifestyles and budget.

HTR 680x450

HTR 800x600

HTR 800x600-curved

Model
HTR
680x450

HTR
800x600

HTR
800x600C

Number of Bars

Discreet with concealed cable
kit

Height mm

680

800

Versatile and easily installed
into new or existing homes

Width mm

450

600

Fixing accessories kit, including
a diamond drill bit (for tiles),
for installation convenience

Depth mm

120

150

European compliant and CE
marked

BTU output

188

341

Wattage

100

Features
Sleek contemporary design
Even heat all at once and
energy efficient

5-Year Warranty

Technical Data
Concealed Wiring
Adaptor available

Amps @ 230Vac

0.23

0.43

IP Rating

IP34

Call us now 0845 345 2288 or visit www.warmup.co.uk

Price Guide
Size & Description

Price (Excl 20% VAT)

HTR 680 x 450

£187.49

HTR 800 x 600

£233.33

HTR 800 x 600 - Curved bars

£266.66

Concealed Wiring Adaptor

£9.99

Scan the code for more information
about this product.
Always refer to the installation manual
prior to commencing your project.

Installation Guide
(Refer to installation manual for complete instructions)
The Towel Rails can be mounted by holding the Towel Rail in the
desired position on the wall. Mark the position on the wall, remove
the Towel Rail and drill holes into the tile/wall. Screw wall anchors
into position, affix the Towel Rail onto the anchors and tighten with
an allen key. Feed or recess power cables to point of connection.
The Towel Rail must be wired by a certified electrician.

Frequently Asked Questions
What material are the Towel Rails made from?
Warmup heated Towel Rails are made from the highest quality
stainless steel.
Do I need any special tools?
The kit comes complete with fixing accessories, including a
diamond drill attachment for tiles for installation convenience.
What can I fix the Towel Rail onto?
The Towel Rail is designed to be fixed through wall cladding into
solid wall framing, solid cement or masonry walls. Plasterboard
toggles, at least 3mm diameter, may be used for two of the
towel rail fixings.

The world’s best-selling floor heating brand

Outdoor Heating Solutions
When it comes to safety in winter, every precaution
should be taken. Using Warmup’s outdoor heating
solutions mean dangerous ice and snow
build-up is reduced in concrete, paved or asphalt
areas minimising the risk of accidents.

For Commercial and Residential use
Warmup offers a range of solutions, whether commercial
walkways, loading docks and ramps or residential driveways
and stairs.

Snow Melting Cables
The resistance-heating element has a single end connection
and is completely grounded and safe. The 25W/m cable is ideal
for outdoor areas in concrete, under pavers or asphalt.
The Snowmelt Cable is available in 2 different versions to suit
concrete/slab and asphalt and offers a 10 year warranty.
For more information on the systems available or
application of Snowmelt, please contact our Sales Support
Team on 0845 345 2288 or visit www.warmup.co.uk

Concrete
Applications

Asphalt
Applications

Scan the code for more information
about this product.
Always refer to the installation manual
prior to commencing your project.

Call us now 0845 345 2288 or visit www.warmup.co.uk

Self-Regulating Cable
During the winter months when the temperature drops
and the snow fall increases, roofs and gutters are affected.
Warmup’s Self-Regulating Cable is perfect to protect pipes from
freezing and gutters, roofs and downspouts from dangerous
accumulation of ice and snow.
One of the unique differences between the Self-Regulating
Cable and traditional heating cables is that the Self-Regulating
Cable can be cut to the exact length required without damaging
the heating properties of the cable.
Once the cable is in operation, it de-ices roofs and gutters from
snow build-up by responding to the ambient temperatures –
the heating output increasing, the colder the weather.
This ambient response function provides an energy efficient
solution as it only increases its heating output when needed
and achieves freeze protection by creating clear drain paths
required for melted snow and ice to flow freely, avoiding the
adverse results of winter.
For more information on the application of the
Self-Regulating Cable, please contact our Sales Support
Team on 0845 345 2288 or visit www.warmup.co.uk

Scan the code for more information
about this product.
Always refer to the installation manual
prior to commencing your project.

The world’s best-selling floor heating brand

Patio Heaters
Warmup patio heaters are the perfect choice
for outdoors in courtyards, conservatories
and gardens.

Warmup patio heaters emit radiant heating to warm
an area up to 10m2
Heaters can be fixed or you can purchase a tripod to
give flexibility to move the heater
Heats-up in seconds, provides coverage of c.10m2
Cost effective - 5 times CHEAPER to run than an
equivalent gas heater
Heaters are water-resistant
Guaranteed for 5,000 hours of usage
No need to refill

Scan the code for more
information about this
product.
Always refer to the
installation manual prior to
commencing your project.

Warmup Patio
heater with tripod

Price Guide

Code

Description

Price (Excl 20% VAT)

WPH – 1760

Patio Heater

£166.66

WPH-TP

Patio Heater Tripod

£104.17

WPH – TPB

Tripod Bracket

£35.00

Call us now 0845 345 2288 or visit www.warmup.co.uk

4 Easy Steps to Calculate your
Underfloor Heating Requirements
for Electric Systems
To calculate the underfloor heating system(s) you require for
your room(s), you need to determine the working floor space
available to you. This is essentially the total amount of floor
space less the area taken up by any fixed objects, i.e. kitchen
units, bath etc. as you do not place your cable/mat in these
areas. You only need to heat the area you will be walking on.
We would recommend that you allow a 5 centimetres (2
inch) gap between the walls and the area where you intend
to install the heating system.

Step 1 - Work out the total floor area. If the overall room is
rectangle in shape, say 4m by 3m – all you need to do is multiply
both numbers – which gives you 12 sqm.
Step 2 - Work out how much of the floor space is taken up
by fixed objects, i.e., in your kitchen – start with the big items
and finish with small items. For example, assume you have
kitchen floor units 600mm in depth x 3m long; a free standing
fridge, 600mm x 600mm. You need to calculate these areas i.e,
0.6m x 3.0m = 1.8sqm and 0.6m x 0.6m = 1.2sqm = Total area
3.0sqm.
Step 3 - From Step 1 and Step 2 you now know the amount of
fixed space: Step 1: 12 sqm Step 2 = 3 sqm
Step 4 - Now calculate the amount of free floor space for your
Warmup cable or mat:
Floor space = 12 sqm – 3 sqm = 9 sqm. Therefore, 9sqm is
what you require from your chosen Warmup system.
The world’s best-selling floor heating brand

Warmup
Hydronic
Underfloor
Heating Systems
Warmup offers you a complete bespoke solution
Warmup hydronic heating systems come designed and supplied
with a full set of high quality components and controls ready for
installation. Systems are available in a number of configurations
and components guaranteed to perfectly match your project and
budget.
Warmup systems come with a choice of 3 pipe types; PEX-A, PE-RT
and PE-RT/AL/PE-RT. This choice guarantees that you have the best
possible system, tailored to your specific installation and budget.
Warmup PEX-A hydronic pipe carries a Lifetime Warranty for
greater peace of mind. All other pipes carry a 50 year Warranty.

LIFETIME
LIMITED

WARRANTY

Our unique SafetyNet™ Installation Guarantee means that should
you accidentally damage the pipe on site, Warmup will exchange
it free of charge.

Flooring
Types

Screed and
Concrete Floors

Timber Suspended
and Batten Floors

Total-16

Page Number

60 - 69

70 - 77

78 - 79

Tile & Stone
Hardwood
Carpet
Laminate
Vinyl

Call us now 0845 345 2288 or visit www.warmup.co.uk

The world’s best-selling floor heating brand

Warmup
HydroPack
Installation Kit
HydroPack is an easy-to-specify kit that comes with everything you
need to install hydronic underfloor heating. It is the ideal solution
for small projects of 22m2 or less (additional products available for
larger rooms), providing a maximum heat output of up to 3kW. The
kit includes the Warmup 3iE thermostat, the PE-RT pipe plus all the
components necessary to complete a successful underfloor heating
installation in a few hours.
HydroPack allows you to quickly purchase and install a hydronic
system without the need to purchase each component separately.
All the components are compatible and from a single source,
packaged in one convenient kit for fast and easy installation.
You will need to ensure that the heat source has the sufficient
capacity to supply sufficient energy for the HydroPack and other
system requirements.
Features
Compact and lightweight modular installation kit, designed to be connected
onto existing pipework
Everything you need in one handy kit for quick and easy installation

All components are compatible and from a single source for reliability
Ideal solution for small projects of 22m2 or less, providing a maximum heat
output up to 3kW
Carries a comprehensive warranty of fifty (50) years on the pipe. You also get
Warmup’s unique SafetyNet™ Installation Guarantee – this means should you
accidentally damage the pipe on-site, Warmup will replace it free of charge

Call us now 0845 345 2288 or visit www.warmup.co.uk

HydroPack Kit Contents
The HydroPack installation kit is made up of
16mmx120m PE-RT pipe

Single room “A” rated energy efficient circulating pump/
mixer control unit

Compression fittings x 2

3iE™ Energy-Monitor Thermostat

Pipe clips x 600

Pipe cutter

HydroPack – 22m UFH system
Installation & User Guide
2

Installation instructions
Ideal for conservatories & extensions

Pump/mixing unit
Technical Specification
Compact bolt-on unit provides quick and easy installation
Easy to set-up with an adjustable temperature range of 35 oC to 65 oC
Delivers controlled mixed temperature water to the underfloor heating system
with heat output of up to 3kW
Controls flow temperature to +/-2 oC with changing boiler flow and return
temperature
Maximum Static Pressure:

10 bar

Maximum Temperature:

90 °C

Adjustable Control Range:

35 - 65 °C

Factory Pre-set:

35 °C (Minimum setting)

Fail Safe Feature

The world’s best-selling floor heating brand

Installation Guide
(Refer to installation manual for complete instructions)
Before commencing installation, ensure the insulation is laid on a
clean and level subfloor. A perimeter strip or edge insulation will
need to be laid around the perimeter of the room. The insulation
should conform to building regulations or practices and laid as per
manufacturers instructions.
The compact control and pump unit should be wall mounted in
a vertical position on a suitable wall. Choose a suitable & solid
mounting location, ensuring adequate clearance for primary and
underfloor heating pipework and accessibility of the control unit.
Begin to unwrap and uncoil the pipe from the inside centre of the
coil, cut the end off with the cutters to leave a neat square cut, but
leaving a rounded pipe (i.e. not compressed). Once the pipe has
gone through the compression fitting, insert the pipe into the flow
from the mixer pump assembly for the underfloor heating. Refer to
installation instructions.
Once connected, begin laying the pipework around the room using
the preferred pipe pattern (see examples below). Take care to turn
the coil of pipe as you uncoil it to relieve tension and staple the pipe
using the pipe clips provided into the insulation. An allowance of 5
clips per linear metre of pipe has been included. However less clips
may be required on the straight runs and more required on the loops.

Spiral pipe layout
(for rectangular
shaped rooms where
even spread of heat is
required)

Serpentine pipe layout
(for odd shaped or
specific-heat areas, i.e.
to concentrate flow near
windows or doors)

Call us now 0845 345 2288 or visit www.warmup.co.uk

Once the pipework has been laid, work out where to cut the pipe
for the final connections to the pump/mixer kit. Insert into the final
compression fitting and connect to the pump/mixer valve. Tighten
the compression fittings.
First the pipework will need to be filled and flushed with fresh cold
water from the mains supply. Connect your hose to the flow side of
the mixing valve that will be connected to the main flow from the
heating system. Connect a hose to the return side of the mixing
valve, that will flow back to the heat source for reheating. Place the
mains water supply and flush through with the mains water until no
air bubbles can be seen in the discharge of water.
Using a pressure testing kit (available for hire from your local plant/
test hire or purchase from your local plumbers merchant), connect
to the red valve and open. Build the pressure up to 6 Bar and hold
for 1 hour. Once the test is complete then the system needs to be
left under pressure during the screeding process. At least 2 Bar
pressure is recommended for the process. This way if the pipework
is damaged a leak and drop in pressure will be shown, then
remedial repair work can take place as required.
Once the system has been installed and pressure tested it should be
protected by laying the floor screed as soon as possible.
Completing the job
If using a standard sand/cement screed, a thickness of between
65mm & 75mm on top of the insulation is recommended. The
screed & screeding works must comply with current Building
Regulations and attention must be paid to the curing times. Under
no circumstances should the underfloor heating system be used
to force curing of the screed. The mixing valve on the control pack
should be set to the minimum temperature when commissioning
commences after the screed has cured as per manufacturers
instructions. Run with the heat on continuously for 3 days, after
this a steady increase of 2 - 3°C per day can be adopted up to the
desired working temperature. Then run for a further 4 days at
this temperature. Ensure relative humidity of the screed is correct
before laying floor finishes.
1. Floor Covering
2. Screed
3. Warmup Pipe
4. Warmup Clip
5. Warmup Clypso insulation
6. Subfloor with built in DPM
7. Perimeter insulation

1
2

4
5

The world’s best-selling floor heating brand

Screed and Concrete Floors

Warmup Clypso
System
The Clypso System uses plastic clips to secure the underfloor
heating pipe to laminated insulation panels. The panels are
constructed from either PIR (polyisocyanurate) or expanded
polystyrene insulation with a fabric reinforced foil laminated to
their surface. The foil on each panel comes with two flaps, for
taping to the adjoining panel, thereby increasing water resistance
and separating the insulation layer from the wet screed.
The laminated foil is printed with a grid pattern to make consistent
pipe-spacing easier for the installer, especially when required to
work around obstacles or a spiral installation pattern.
Insulation must comply with Building Regulations in force at the
time of approval and BS/EN1264.
The Clypso System is suitable for almost any floor finish and in
particular where the flooring (wood, carpet or vinyl) may be
replaced from time to time.
Insulation Features
The insulation is lined in 50mm grids to assist the installer in quickly placing the
pipes in the correct design format and helps speed-up the installation process
Insulation fabric reinforced foil layer is woven to deliver extra security for
retention of the pipe. This also makes it easier to install and provides additional
protection against damage to the pipe prior to screed being laid
Various compressive strengths are available, which safely allows the floor buildup to take imposed loads without damaging the integrity of the floor

LIFETIME
LIMITED

WARRANTY

When PEX-A
Pipe is used

Other pipes carry
50 year warranty

Call us now 0845 345 2288 or visit www.warmup.co.uk

Installation Guide
(Refer to installation manual for complete instructions)
Make a layout plan of your floor area by measuring your room and
then subtract any fixtures (such as baths and cupboards).
Ensure the installation area is dry and sealed to the elements and
that you have a level floor surface. If installation is to take place onto a
concrete base, install Warmup’s polyethylene damp proof membrane
and assess whether supplementary insulation is required before
installing a perimeter insulation to prevent heat loss, allowing for some
subfloor expansion due to temperature changes. Although insulation
is an integral part of the Clypso System, it may not fully comply with
Building Regulations for new-build projects; additional insulation may
be required, depending on the existing subfloor construction.
The Clypso Insulation panels are then installed, covering the entire
floor area providing an insulated surface for pipe installation. Once the
Insulation panels are in place and the overlapping foil is taped down,
the Warmup pipe circuits can be installed using a purpose-built clip
gun and Warmup clips.
The pipe is then fixed into place on the Clypso Insulation panels
according to a predesigned pattern.
Before the screed is poured, attach the pipe to the manifold and
pressure test to ensure the system is sound. The system should be left
under pressure until the flooring process is complete.
Completing the job
Once the system has been tested, the screed should be laid over the
system as soon as possible to prevent damage to the pipe and to
allow the drying process to begin. The screed must be allowed to dry
naturally until full strength is reached before turning on the underfloor
heating, unless the screed manufacturer’s instructions say otherwise.
The heating system is then turned on, gradually increasing the
temperature of the floor over a number of days until the desired
temperature is reached. Turning on the system too early or too high
will dry the screed too quickly, damaging the screed. Underfloor
heating and screed commissioning must take place as per
manufacturer’s instructions and British Standards.
1. Floor Covering
2. Screed
3. Warmup Pipe
4. Warmup Clip
5. Warmup Clypso insulation
6. Subfloor with built in DPM
7. Perimeter insulation

1
2
3

4
5

The world’s best-selling floor heating brand

Screed and Concrete Floors

Warmup Metro
Rail System
The Metro Rail System uses pre-moulded retention clips. The rail is
located on top of the insulation layer and is separated by a plastic
membrane. The Metro Rail System allows pipes to be spaced as
close as 50mm. The system holds the pipework in place until the
screed is applied.
It is suitable for almost any floor finish and in particular where the
flooring (wood, carpet or vinyl) may be replaced from time to time.
Features
Designed to allow quick and easy installation - the rail provides guidance on
how to install the pipework quickly and at the correct design spacing levels
Holds the pipe at the correct level prior to screeding to ensure there are no hot
spots

LIFETIME
LIMITED

WARRANTY

When PEX-A
Pipe is used

Other pipes carry
50 year warranty

Call us now 0845 345 2288 or visit www.warmup.co.uk

required before installing a perimeter insulation to prevent heat
loss, allowing for some subfloor expansion due to temperature
changes. Although insulation is an integral part of the Metro Rail
System, it may not fully comply with Building Regulations for newbuild projects; additional insulation may be required, depending on
the existing subfloor construction.
The Insulation panels are then laid and fixed to the subfloor
throughout the room and covered with a plastic membrane before
installing the Metro Rail system on top. The Metro Rails are held in
place using either an adhesive backing or by integrated fixing pins,
depending on the insulation system used.
When the Metro Rail system is firmly fixed in place the pipe is then
laid according to a predesigned pattern.
Once installed, attach the pipe to the manifold and pressure test
to ensure the system is sound. The system should be left under
pressure until the flooring process is complete.
Completing the job
Once the system has been tested, the screed should be laid over
the system as soon as possible to prevent damage to the pipe and
to allow the drying process to begin. The screed must be allowed
to dry naturally until full strength is reached before turning on the
underfloor heating, unless the screed manufacturer’s instructions
say otherwise.
The heating system is then turned on, gradually increasing the
temperature of the floor over a number of days until the desired
temperature is reached. Turning on the system too early or too high
will dry the screed too quickly, damaging the screed. Underfloor
heating and screed commissioning must take place as per
manufacturer’s instructions and British Standards.
1. Floor Covering
2. Screed
3. Warmup Pipe
4. Warmup Metro Rail
5. Plastic Membrane
6. Insulation
7. Subfloor with built in DPM
8. Perimeter Insulation

2
8
3

4
5

6
7

The world’s best-selling floor heating brand

Screed and Concrete Floors

Warmup Tella Grid
System
The Tella Grid System uses a wire grid to which the underfloor
heating pipework is attached using Warmup plastic cable ties.
The wire grid is typically used to add structural support to the
subfloor where extra strength is required due to high floor loadings.
The Tella Grid System is suitable for almost any floor finish and
in particular where the flooring (wood, carpet or vinyl) may be
replaced from time to time.
Features
Wire grid provides best solution when a structural screed is required,
particularly for heavy and high loads
Grid protects the integrity of the insulation from damage until the structural
screed is laid

LIFETIME
LIMITED

WARRANTY

When PEX-A
Pipe is used

Other pipes carry
50 year warranty

Call us now 0845 345 2288 or visit www.warmup.co.uk

loss, allowing for some subfloor expansion due to temperature
changes. Warmup insulation panels are an integral part of the Tella
Grid System, however, for new-build projects, additional insulation
may be required to comply with building regulations, depending
on the existing subfloor construction.
The Insulation boards are then laid and fixed to the subfloor
throughout the room and covered with a plastic membrane before
installing the Tella Grid.
Warmup’s heating pipe is then laid out according to a predesigned
pattern until your desired heated area is covered. The pipe should
then be secured to the Tella Grid with plastic cable ties.
Then attach the pipe to the flow connection on the manifold and
pressure test to ensure the system is sound. The system should be
left under pressure until screeded.
Completing the job
Once the system has been tested, the screed should be laid over
the system as soon as possible to prevent damage to the pipe and
to allow the drying process to begin. The screed must be allowed
to dry naturally until full strength is reached before turning on the
underfloor heating, unless the screed manufacturer’s instructions
say otherwise.
The heating system is then turned on, gradually increasing the
temperature of the floor over a number of days until the desired
temperature is reached. Turning on the system too early or too high
will dry the screed too quickly, damaging the screed. Underfloor
heating and screed commissioning must take place as per
manufacturer’s instructions and British Standards.

1. Floor Covering
2. Screed
3. Warmup Pipe
4. Plastic Cable Tie
5. Warmup Wire Grid
6. Warmup Insulation
7. Subfloor with built in DPM
8. Perimeter Insulation

1
2

3
5

6
7

The world’s best-selling floor heating brand

Screed and Concrete Floors

Warmup Nexxa
Panel System
The Nexxa Panel System is used primarily where there are floor
build-up issues to deal with. It can substantially reduce the overall
build-up of the floor structure.
Warmup system plates are interlocking vacuum formed sheets of
plastic, incorporating pipe-locating castles. Sheets are laid over
the sub floor and thermally insulated within the castellations and
10mm as a base. Additional insulation may be required to meet
the Building Regulations. The edges are over-lapped by 75mm
inter-locking them to form a continuous layer.
The Nexxa Panel System is suitable for almost any floor finish and
in particular where the flooring (wood, carpet or vinyl) may be
replaced from time to time.
Features
Nexxa panel being of a low build up of just 30mm including the 20mm
castellation is ideal for refurbishments or new build where a low build up floor
is required
Retains pipework prior to screeding
Self-retaining system, no clips required

LIFETIME
LIMITED

WARRANTY

When PEX-A
Pipe is used

Other pipes carry
50 year warranty

Installation Guide
(Refer to installation manual for complete instructions)
Make a layout plan of your floor area by measuring your room and
then subtract any fixtures (such as baths and cupboards).

Call us now 0845 345 2288 or visit www.warmup.co.uk

Ensure the installation area is dry and sealed to the elements
and that you have a level floor surface. If installation is to take
place onto a concrete base, install Warmup’s polyethylene damp
proof membrane and assess whether supplementary insulation is
required before installing a perimeter insulation to prevent heat
loss, allowing for some subfloor expansion due to temperature
changes. Although insulation is an integral part of the Nexxa Panel
System it may not fully comply with Building Regulations for newbuild projects; additional insulation may be required, depending on
the existing subfloor construction.
The Nexxa Panels should be laid to have the edges overlapping by
75mm and interlocking with each new panel, creating a continuous
layer.
Warmup’s heating pipe is then laid out according to a predesigned
pattern, ensuring that the pipe is firmly clipped down in each panel.
Once installed, attach the pipe to the manifold and pressure test
to ensure the system is sound. The system should be left under
pressure until the flooring process is complete.
Completing the job
Once the system has been tested, the screed should be laid over
the system as soon as possible to prevent damage to the pipe and
to allow the drying process to begin. The screed must be allowed
to dry naturally until full strength is reached before turning on the
underfloor heating, unless the screed manufacturer’s instructions
say otherwise.
The heating system is then turned on, gradually increasing the
temperature of the floor over a number of days until the desired
temperature is reached. Turning on the system too early or too high
will dry the screed too quickly, damaging the screed. Underfloor
heating and screed commissioning must take place as per
manufacturer’s instructions and British Standards.
1. Floor Covering
2. Screed
3. Warmup Pipe
4. Warmup Nexxa Panel
5. Warmup Insulation
6. Subfloor with built in DPM
7. Perimeter Insulation

1
2

4
3

The world’s best-selling floor heating brand

Screed and Concrete Floors

Warmup Forte
Grid System
The Forte Grid System is designed for installation into load-bearing
structural floors.
The Forte Grid System incorporates wire grids to which the
underfloor heating pipework is attached using cable ties.
The Forte Grid System is either located within a concrete or
structural screed, but is suitable for almost any floor finish, in
particular where the flooring is for a commercial application, such
as epoxy paint or resin.
Features
Pipework is fastened to the reinforced bars without impacting the integrity of
the floor
To ensure the most heat responsive floor, the pipe can be installed in the
centre of the concrete zone

LIFETIME
LIMITED

WARRANTY

When PEX-A
Pipe is used

Other pipes carry
50 year warranty

Call us now 0845 345 2288 or visit www.warmup.co.uk

changes. Warmup insulation panels are an integral part of the Tella
Grid System, however, for new-build projects, additional insulation
may be required to comply with building regulations, depending
on the existing subfloor construction.
The Insulation boards are then laid over a compacted level bed of
hardcore and fixed to the subfloor throughout the room before
being covered with a plastic membrane.
The Forte Grids are then laid over the plastic membrane.
Warmup’s heating pipe is then laid out according to a predesigned
pattern, with the pipe being secured to the Forte Grid with plastic
cable ties.
In some cases, an additional structural reinforcement grid can be
added above the pipe for additional strength. This additional grid
will normally be laid on castles to ensure the mesh is at the correct
height ready for the screeding process.
Once installed, attach the pipe to the manifold and pressure test
to ensure the system is sound. The system should be left under
pressure until the flooring process is complete.
Completing the job
Once the system has been tested, the screed should be laid over
the system as soon as possible to prevent damage to the pipe and
to allow the drying process to begin. The screed must be allowed
to dry naturally until full strength is reached before turning on the
underfloor heating, unless the screed manufacturer’s instructions
say otherwise.
The heating system is then turned on, gradually increasing the
temperature of the floor over a number of days until the desired
temperature is reached. Turning on the system too early or too high
will dry the screed too quickly, damaging the screed. Underfloor
heating and screed commissioning must take place as per
manufacturer’s instructions and British Standards.
1. Floor Covering
2. Concrete
3. Warmup Forte Grid
4. Plastic Membrane
5. Warmup Insulation
6. Subfloor with built in DPM
7. Perimeter Insulation

1
2

3
4

The world’s best-selling floor heating brand

Timber Suspended and
Batten Floors

Warmup Econna
Joisted Floor
System
The Econna Joisted Floor System is a composite wood load bearing
slotted 22mm floor with return ends.
It is designed to fit on top of standard wood joists of 400mm to
600mm c/c max. This replaces the standard board in the floor
construction.
The Econna Joisted Floor System is suitable for almost any floor
finish, in particular where the flooring (wood, carpet or vinyl) may
be replaced from time to time.
Features
Pipe is built into the structural floor, allowing faster heat-up response times
No screeding required

LIFETIME
LIMITED

WARRANTY

When PEX-A
Pipe is used

Other pipes carry
50 year warranty

Installation Guide
(Refer to installation manual for complete instructions)
Make a layout plan of your floor area by measuring your room and
then subtract any fixtures (such as baths and cupboards).
Before commencing installation, assess whether supplementary
insulation is required. Although insulation is an integral part of the
Econna System it may not fully comply with Building Regulations

Call us now 0845 345 2288 or visit www.warmup.co.uk

for new-build projects; additional insulation may be required,
depending on the existing subfloor construction.
Rigid insulation of the required depth is placed between the joists
before laying the Econna routed flooring layer. The Econna routed
flooring layer is then screwed to the joists avoiding the pre-routed
groves.
Warmup aluminium diffusion plates are then laid on top of the
Econna routed flooring layer in the straight grooves only, leaving
the return grooves bare.
The Warmup Pipe is then fitted into the Diffusion Plate and Econna
Routed groves according to a predesigned pattern.
Once installed, attach the pipe to the manifold and pressure test
to ensure the system is sound. The system should be left under
pressure until the flooring process is complete.
Completing the job
Once the system has been tested, the final flooring should be laid
over the system as soon as possible to prevent damage to the pipe.
The heating system is then turned on, gradually increasing the
temperature of the floor over a number of days until the desired
temperature is reached. Turning on the system too early or too high
will damage the flooring.
Design parameters should not be exceeded and specific
manufacturer’s information should be adhered to.

1. Timber Floor Covering (18mm minimum)
2. Optional Thin Wood Floor Underlay
3. Warmup Diffusion Plate
4. Warmup Pipe
5. Warmup Econna Routed Flooring
6. Joists
7. Insulation

1
2

4
5
7

The world’s best-selling floor heating brand

Timber Suspended and
Batten Floors

Warmup Silva
Joisted Floor
System
The Silva Joisted Floor System is installed in many refurbishment
projects.
Joists traditionally tend to be installed at 400mm centres. However,
Warmup can supply a more bespoke system to suit individual
properties with varying joist centres as required.
The Silva Joisted Floor System is suitable for almost any floor finish,
in particular where the flooring is wood or engineered wood.
Features
Suitable for use under existing wooden floors
System installed between floor joists
Does not impact on floor heights
Lightweight screed provides fast heat-up response times

LIFETIME
LIMITED

WARRANTY

When PEX-A
Pipe is used

Other pipes carry
50 year warranty

Installation Guide
(Refer to installation manual for complete instructions)
Make a layout plan of your floor area by measuring your room and
then subtract any fixtures (such as baths and cupboards).
The Clypso insulation for the Silva Joisted Floor system is installed
between the existing joists using battens or noggins to hold the
insulation in place. The Clypso insulation should be fitted tight to
the joists without any gaps and should cover the entire floor area,

Call us now 0845 345 2288 or visit www.warmup.co.uk

providing an insulated surface for pipe installation. Any holes or
gaps that cannot be covered by the insulating panels should be
filled using expanding foam.
The height of the Clypso Insulation panels should be set so that
the top of the panels are in accordance with the system design,
allowing for proper coverage of the pipe by the lightweight screed
and to finish level with the joists.
In order to feed the pipe across a joist, a notch is cut into the top of
the joist.
Once the Clypso Insulation panels are in place, the pipe circuits can
be installed according to a predesigned pattern using a purposebuilt clip gun and Warmup clips.
Before the screed is poured, the Warmup pipe is attached to
the manifold and pressure tested to ensure the system is sound.
The system is then left under pressure until the flooring process is
complete.
Completing the job
Once the system has been tested, the screed should be laid over
the system as soon as possible to prevent damage to the pipe and
to allow the drying process to begin.
The screed should be level with the top of the joists and must
be allowed to dry naturally until full strength is reached before
installing the floor covering.
The heating system is then turned on, gradually increasing the
temperature of the floor over a number of days until the desired
temperature is reached. Turning on the system too early or too high
will dry the screed too quickly, damaging the screed. Underfloor
heating and screed commissioning must take place as per
manufacturer’s instructions and British Standards.
1. Floor Covering
2. Lightweight Screed
3. Joists
4. Warmup Pipe
5. Warmup Clip
6. Insulation with membrane

1
2

3
6

The world’s best-selling floor heating brand

Timber Suspended and
Batten Floors

Warmup Tectora
Joisted Batten
Floor System
The Tectora Joisted Batten Floor System is particularly suitable
where there is a sprung/cradled battened floor or floor joists. It can
be used in battened installations over a concrete subfloor, variable
height floor battens are employed to create a void of between 50
to 100mm.
The batons can be sprung or on cradles to create an acoustic floor.
For this installation, a diffusion plate system is generally used if
standard installation types are not suitable.
For installing as a joisted system, the rigid insulation is placed
between the joists to support the diffusion plates, as they span the
joists.
The Tectora Joisted Batten Floor System is suitable for almost any
floor finish, in particular wood or engineered wood.
Features
Diffusion plates spread heat efficiently without increasing floor build-up
System promotes fast heat-up response times
No screeding required

LIFETIME
LIMITED

WARRANTY

When PEX-A
Pipe is used

Other pipes carry
50 year warranty

Call us now 0845 345 2288 or visit www.warmup.co.uk

Installation Guide
(Refer to installation manual for complete instructions)
Make a layout plan of your floor area by measuring your room and
then subtract any fixtures (such as baths and cupboards).
Required battens to support the insulation will need to be designed
and installed by the flooring contractor and co-ordinated with the
installer of the Tectora System.
Ensure the installation area is dry and sealed to the elements and
that you have a level floor surface. If installation is to take place onto a
concrete base, install Warmup’s polyethylene damp proof membrane.
You should assess whether supplementary insulation is required
before installing a perimeter insulation to prevent heat loss, allowing
for some subfloor expansion due to temperature changes. Although
insulation is an integral part of the Tectora System it may not fully
comply with Building Regulations for new-build projects; additional
insulation may be required, depending on the existing subfloor
construction.
Rigid insulation of the required depth is placed between the
preinstalled battens before fixing the Tectora diffusion plates to the
battens with screws.
The Warmup pipe is then fitted into the Tectora diffusion plates groove
according to a predesigned pattern.
Once installed, attach the pipe to the manifold and pressure test to
ensure the system is sound. The system should be left under pressure
until the flooring process is complete.
Completing the job
Once the system has been tested, the final flooring should be laid over
the system as soon as possible to prevent damage to the pipe.
The heating system is then turned on, gradually increasing the
temperature of the floor over a number of days until the desired
temperature is reached. Turning on the system too early or too high
will damage the flooring.
Design parameters should not be exceeded and specific
manufacturer’s information should be adhered to.
1. Floor Covering
2. Battens
3. Warmup Tectora Diffusion Plates
4. Warmup Pipe
5. Warmup Insulation
6. Subfloor with built in DPM

3
4

The world’s best-selling floor heating brand

Timber Suspended and
Batten Floors

Warmup Contura
Floating Floor
System
The Contura Floating Floor System (combines preformed insulation
and diffusion plates) is used where heating is installed onto a
concrete or solid wooden subfloor but where a dry finish is used in
place of a standard screed covering.
This system typically has a lower wattage per square metre output
(75w/m²) compared to traditional screeded floors.
It is used primarily in new build on upper floors where insulation
levels are higher, lowering the heat requirements.
It is suitable in refurbishment projects where sufficiently increased
levels of insulation is applied. It can be installed under almost any
floor finish, in particular engineered wood and composite laminate
wood.
Features
Comprehensive choice of board strengths and thickness available to match
individual requirements
Overlay system requires no screeding
System promotes fast heat-up response times

LIFETIME
LIMITED

WARRANTY

When PEX-A
Pipe is used

Other pipes carry
50 year warranty

Call us now 0845 345 2288 or visit www.warmup.co.uk

Installation Guide
(Refer to installation manual for complete instructions)
Make a layout plan of your floor area by measuring your room and
then subtract any fixtures (such as baths and cupboards).
Ensure the installation area is dry and sealed to the elements
and that you have a level floor surface. As the Contura Floating
Floor System is installed directly onto a concrete base, install
Warmup’s polyethylene damp proof membrane, assess whether
supplementary insulation is required. Insulation is an integral part
of the Contura System, but may not fully comply with Building
Regulations for new-build projects; additional insulation may be
required, depending on the existing subfloor construction.
Lay the Contura Insulation directly onto the concrete subfloor
before fitting Warmup’s diffusion plates in the straight groves of the
insulation only, leaving the return grooves clear.
Carefully insert the Warmup pipe into the pre-moulded Contura
grooves according to a predesigned pattern until your desired
heated area is covered.
Once installed, attach the pipe to the manifold and pressure test
to ensure the system is sound. The system should be left under
pressure until the flooring process is complete.
Completing the job
Once the system has been tested, the final flooring should be laid
over the system as soon as possible to prevent damage to the pipe.
The heating system is then turned on, gradually increasing the
temperature of the floor over a number of days until the desired
temperature is reached. Turning on the system too early or too high
will damage the flooring.
Design parameters should not be exceeded. Manufacturer’s
instructions must be followed.

1. Floor Covering
2. Warmup Diffusion Plate
3. Warmup Pipe
4. Warmup Contoured Insulation
5. Subfloor with built in DPM

2
3

The world’s best-selling floor heating brand

NEW! NEW! NEW!

Insulation

Warmup Total-16
Low Profile System
Total-16 is a low build (16mm), no screed required, lightweight
yet heavy-duty hydronic insulation system with inbuilt diffusion
plate.
The system is designed for use with Warmup’s 12mm PEX-A pipe,
which is inserted into the insulation boards. Warmup’s 12mm
PEX-A pipe is at the heart of the low profile system because it
is strong, flexible and kink resistant and it comes with our best
warranty and guarantee.
With Total-16’s build-up of only 16mm and the straight boards
supplied with integrated aluminium heat diffuser plates, the
installation time is significantly reduced. This makes Total-16
ideal for new-build and refurbishment projects where floor
height is at a premium and installation speed is of the essence.
Total-16 is installed onto either concrete or wooden sub-floors
and can be used under almost any floor finish, including solid
and engineered wood, ceramic, stone floors as well as vinyl and
carpet.
Total-16 is comprised of straight boards, with integrated
aluminium plates, multi-feed boards and return boards. These
boards are made of a high density EPS and can support 40
tonnes/m2.
Features

Specification

Suitable for almost any floor finish,
including tiles

Thermal conductivity:
0.034 W/mK @ 10° C

Ultra low weight - only 1.7 Kg for the
straight, multi-feed and return boards

Compressive strength: 400kPa
(40 tonnes/m²)

Ultra low height - only 16mm

Thermal output: Up to 111 W/m²

Aluminium heat diffusion plates are
pre-installed, reducing installation time

Straight boards are moulded at
150mm pipe centres

Can be supplied with or without return
ends

LIFETIME
LIMITED

WARRANTY

Call us now 0845 345 2288 or visit www.warmup.co.uk

Installation Guide
(Refer to installation manual for complete instructions)
Make a layout plan of your floor area by measuring your room and
then subtract any fixtures (such as baths and cupboards).
Before commencing installation, assess whether supplementary
insulation is required. Insulation is an integral part of the Warmup
Total-16, but may not fully comply with Building Regulations for
new-build projects.
Ensure the installation area is dry, level and sealed from the
elements. In most cases Total-16 can be laid as a floating floor, but
for tiled flooring or vinyl flooring in wet areas, the Total-16 boards
must be fixed to the subfloor using Seal Adhesive or Glue (see p89).
When tiling on Total-16, the boards and aluminium plates must be
primed using Warmup’s WHS-X-Primer. For heavy footfall areas,
tiling directly onto the Total-16 boards is not recommended.

12 mm.

16 mm.

Lay the Total-16 low profile system to match the layout plan.
Carefully insert the PEX-A 12mm pipe into the pre-moulded
groves until your desired heated area is covered.
Then attach the 12mm PEX-A pipe to the flow connection on the
manifold - use the Warmup pipe bend support (WHS-P-BEND12)
to hold the pipe at a 90° angle. Following a single meander
pattern, install the pipe in the boards by pushing into the
grooves of the heat diffuser plates. Finally, fix another pipe bend
support to the return pipe and connect to the manifold.

1. Floor Covering
2. Diffusion Plate (part of Total-16)
3. Warmup Total-16 Insulation
4. Warmup 12mm PEX-A Pipe
5. Subfloor with built in DPM

4
5

The world’s best-selling floor heating brand

Screed Replacement Board

Warmup Dual
Overlay Concrete
Dual Overlay Concrete is a fast track floor preparation system for
use as a screed replacement system which can be installed over
the Econna, Contura and Total-16 hydronic systems. It is suitable
for installation under many floor coverings such as tiles, wood and
resilient floors.
Installation is quick, clean and dry making it an easier option for
installers. The low heat resistance allows heat to pass through
the floor finish without any reduction to the efficiency, evenly
distributing the heat and alleviating any hot spots.
Dual Overlay Concrete consists of a base and top board. Both
boards are provided with contact adhesive, bonding them together
to make one solid subfloor.

Features
Provides a stable subfloor on which a variety of floor coverings can be laid
Suitable for our Econna & Contura hydronic underfloor heating systems
Installation is quick and easy
Provides even heat distribution

Technical Data
Size

1,200mm x 600mm

Thickness

2 x 6mm

Composition

Cement, Silica (quartz), Cellulose
and filling material, fitted with an
interactive adhesive

Weight per panel (kg)

7.5

Weight per m² (kg)

Tog

0.4

Thermal Rm value (m².K.W.-1)

0.038

Fire Class

EN 13501: 2007 B

fl..s1

Call us now 0845 345 2288 or visit www.warmup.co.uk

Installation Guide
(Refer to installation manual for complete instructions)
The Warmup Dual Overlay is comprised of a 6mm deep cement
bottom board and 6mm deep cement top board. The bottom and
top layers are laid out with staggered joints and arranged so that
the top boards overlap the joints in the base boards. The Warmup
Hydronic Heating System lays below a decoupling layer and the
Dual Overlay Concrete System. This method of installation provides
a stable surface for the floor finish to rest on and avoid any joints
showing through the final floor finish. Finally, the floor finish can
either be glued to the boards as a final layer or simply laid freely
upon them.

Floor Cutaway - Based on Econna Installation
Dual Overlay Concrete with Floating Wood Floor
1. Floating Wood Floor (18mm maximum)
2. Optional Thin Wood Floor Underlay
3. Dual Over Lay Concrete Boards
4. Warmup Pipe
5. Perimeter Strip
6. Decoupling Layer
7. Econna Underfloor Heating System

Dual Overlay Concrete with Glued Wood Floor
1. Glued Wood Floor
2. Fixed 8mm Chipboard Layer
3. Dual Over Lay Concrete Boards
4. Warmup Pipe
5. Perimeter Strip
6. Decoupling Layer
7. Econna Underfloor Heating System

Dual Overlay Concrete with Tiled Floor
1. Tiled floor
2. Flexible tile adhesive with
glassfibre mesh
3. Dual Over Lay Concrete Boards
4. Warmup Pipe
5. Perimeter Strip
6. Decoupling Layer
7. Econna Underfloor Heating System

Dual Overlay Concrete with Resilient Floor
1. Resilient Floor Covering
2. Thinset fibre-reinforced screed
3. Dual Over Lay Concrete Boards
4. Warmup Pipe
5. Perimeter Strip
6. Decoupling Layer
7. Econna Underfloor Heating System

The world’s best-selling floor heating brand

Price Guide
Warmup HydroPack
WARMUP HYDROPACK INSTALLATION KIT
CODE

DESCRIPTION

WHS-HYDRO
PACK-22

HydroPack Installation Kit for
projects up to 22m²

(Excl. VAT)

RRP

PACK
QTY

£715.24

A RATED SINGLE ROOM / ZONE MANIFOLD WITH PUMP /
MIXING UNIT
CODE

DESCRIPTION

WHS-M-SRM01

A Rated Single Room / Zone Manifold
with Pump / Mixing unit

(Excl. VAT)

RRP

PACK
QTY

£535.71

(Excl. VAT)

RRP

PACK
QTY

Warmup Thermostats

4iE ENERGY-MONITOR THERMOSTAT
CODE

DESCRIPTION

4iE™ OB

Onyx Black Programmable Thermostat

£166.66

4iE™ BP

Bright Porcelain Programmable
Thermostat

£166.66

RRP

PACK
QTY

3iE ENERGY-MONITOR THERMOSTAT
CODE

DESCRIPTION

(Excl. VAT)

3iE™ PB

Piano Black Programmable Thermostat

£120.83

3iE™ CC

Classic Cream Programmable Thermostat

£120.83

3iE™ SG

Silver Grey Programmable Thermostat

£129.99

3iE™ LG

Leaf Green Programmable Thermostat

£129.99

3iE™ MB

Madison Blue Programmable
Thermostat

£129.99

3iE™ DP

Deep Pink Programmable Thermostat

£129.99

3iE™ WB

Warm Berry Programmable Thermostat

£129.99

TEMPO DIGITAL PROGRAMMABLE THERMOSTAT
CODE

DESCRIPTION

(Excl. VAT)

RRP

PACK
QTY

ELT PB

Tempo - Piano Black

£83.33

ELT PW

Tempo - Porcelain White

£83.33

Call us now 0845 345 2288 or visit www.warmup.co.uk

J Range Thermostats & Controls
For Heating & Cooling
4-EVENT TIMER THERMOSTAT
CODE

DESCRIPTION

WHS-J-4ET

4 event timer thermostat

(Excl. VAT)

RRP

PACK
QTY

£185.63

(Excl. VAT)

RRP

PACK
QTY

£65.30

(Excl. VAT)

RRP

PACK
QTY

STANDARD AMBIENT DIAL SENSOR
CODE

DESCRIPTION

WHS-J-SEN-A

Standard ambient dial sensor

240V BMS DIGITAL MASTER WIRING CENTRE
CODE

DESCRIPTION

WHS-JBMSDWC

240v BMS Digital master wiring
centre

£867.29

WHS-J-DWC

240v Digital master wiring centre

£722.74

240V STANDARD MASTER WIRING CENTRE
CODE

DESCRIPTION

WHS-J-SWC

240v Standard Master wiring centre

(Excl. VAT)

RRP

PACK
QTY

£291.79

EXTENSION KIT TO CONNECT CAT5E CABLING TO WIRING
CENTRES
CODE

DESCRIPTION

WHS-J-EK

Extension kit to connect Cat5e
cabling to
wiring centres

(Excl. VAT)

RRP

PACK
QTY

£26.55

(Excl. VAT)

RRP

PACK
QTY

£159.14

HUMIDITY SENSOR FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

WHS-J-SEN-H

Humidity sensor for hydronic
systems

HEATING/COOLING SWITCH FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

WHS-JSWITCH

Heating/cooling switch for hydronic
systems

The world’s best-selling floor heating brand

(Excl. VAT)

RRP

PACK
QTY

£195.74

S Range Thermostats & Controls
DIGITAL ROOM THERMOSTAT FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

WHS-CB-D230

Digital room thermostat for hydronic
systems

(Excl. VAT)

RRP

PACK
QTY

£50.89

230V DUAL TEMP THERMOSTAT FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

WHS-CB-M230

230v Dual temp thermostat for
hydronic systems

(Excl. VAT)

RRP

PACK
QTY

£33.07

230V MASTER WIRING BOX 4 ZONE FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

WHS-C-BMASTER01

230v Master wiring box 4 zone for
hydronic systems

(Excl. VAT)

RRP

PACK
QTY

£64.86

230V 4 ZONE SLAVE UNIT FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

WHS-S-SLV4Z

230V 4 zone slave unit for hydronic
systems

(Excl. VAT)

RRP

PACK
QTY

£48.36

230V 6 ZONE SLAVE UNIT FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

WHS-S-SLV6Z

230V 6 zone slave unit for hydronic
systems

(Excl. VAT)

RRP

PACK
QTY

£55.79

230V TAMPERPROOF ROOM THERMOSTAT FOR HYDRONIC
CODE

DESCRIPTION

WHS-S-230TP

230v Tamperproof room thermostat
for hydronic systems

(Excl. VAT)

RRP

PACK
QTY

£34.39

(Excl. VAT)

RRP

PACK
QTY

£9.29

(Excl. VAT)

RRP

PACK
QTY

£79.86

WET AREA BOX & 3METRE CLASS 2 SENSOR 10K
CODE

DESCRIPTION

WHS-S-SEN

Wet Area Box & 3metre class 2
sensor 10k

230V PLUG-IN TIMER FOR HYDRONIC SYSTEMS

CODE

DESCRIPTION

WHS-STIMER230

230v Plug-in timer for hydronic
systems

Call us now 0845 345 2288 or visit www.warmup.co.uk

Insulation & Routed Boards
Due to the nature of all insulation products, specific availability
and shipping terms may apply.
Please contact us on 0845 034 8270 to confirm.

CLYPSO INSULATION BOARD SYSTEMS
(Excl. VAT)

RRP

PACK
QTY

Clypso 25mm thickness gridded insulation
board, EPS 070, 2.4m x 1.2m (pack of 12)

£134.14

WHSCL-B07050

Clypso 50mm thickness gridded insulation
board, EPS 070, 2.4m x 1.2m (pack of 6)

£99.64

WHSCL-B07075

Clypso 75mm thickness gridded insulation
board, EPS 070, 2.4m x 1.2m (pack of 4)

£88.29

WHSCL-B07100

Clypso 100mm thickness gridded
insulation board, EPS 070, 2.4m x 1.2m
(pack of 3)

£82.50

WHSCL-B10025

Clypso 25mm thickness gridded insulation
board, EPS 100, 2.4m x 1.2m (pack of 12)

£177.43

WHSCL-B10050

Clypso 50mm thickness gridded insulation
board, EPS 100, 2.4m x 1.2m (pack of 6)

£143.36

WHSCL-B10075

Clypso 75mm thickness gridded insulation
board, EPS 100, 2.4m x 1.2m (pack of 4)

£131.86

WHSCL-B10100

Clypso 100mm thickness gridded
insulation board, EPS 100, 2.4m x 1.2m
(pack of 3)

£126.11

WHSCL-B07025+

Clypso 25mm thickness gridded insulation
board, EPS 070, 2.4m x 1.2m Premium
range (pack of 12)

£210.43

WHSCL-B07050+

Clypso 50mm thickness gridded insulation
board, EPS 070, 2.4m x 1.2m Premium
range (pack of 6)

£175.93

WHSCL-B07075+

Clypso 75mm thickness gridded insulation
board, EPS 070, 2.4m x 1.2m Premium
range (pack of 4)

£164.57

WHSCL-B07100+

Clypso 100mm thickness gridded
insulation board, EPS 070, 2.4m x 1.2m
Premium range (pack of 3)

£158.79

WHSCL-B10025+

Clypso 25mm thickness gridded insulation
board, EPS 100, 2.4m x 1.2m Premium
range (pack of 12)

£274.71

WHSCL-B10050+

Clypso 50mm thickness gridded insulation
board, EPS 100, 2.4m x 1.2m Premium
range (pack of 6)

£240.21

WHSCL-B10075+

Clypso 75mm thickness gridded insulation
board, EPS 100, 2.4m x 1.2m Premium
range (pack of 4)

£228.86

WHSCL-B10100+

Clypso 100mm thickness gridded
insulation board, EPS 100, 2.4m x 1.2m
Premium range (pack of 3)

£223.07

CODE

DESCRIPTION

WHSCL-B07025

The world’s best-selling floor heating brand

METRO / GENERAL INSULATION BOARD
(Excl. VAT)

RRP

PACK
QTY

Metro/General 25mm thickness
insulation board, EPS 070, 2.4m x
1.2m (pack of 12)

£65.57

WHSMT-B07050

Metro/General 50mm thickness
insulation board, EPS 070, 2.4m x
1.2m (pack of 6)

£65.36

WHSMT-B07075

Metro/General 75mm thickness
insulation board, EPS 070, 2.4m x
1.2m (pack of 4)

£65.43

WHSMT-B07100

Metro/General 100mm thickness
insulation board, EPS 070, 2.4m x
1.2m (pack of 3)

£65.36

WHSMT-B07025+

Metro/General 25mm thickness insulation board, EPS 070, 2.4m x 1.2m
Premium range (pack of 12)

£141.86

WHSMT-B07050+

Metro/General 50mm thickness insulation board, EPS 070, 2.4m x 1.2m
Premium range (pack of 6)

£141.64

WHSMT-B07075+

Metro/General 75mm thickness insulation board, EPS 070, 2.4m x 1.2m
Premium range (pack of 4)

£141.71

WHSMT-B07100+

Metro/General 100mm thickness
insulation board, EPS 070, 2.4m x
1.2m Premium range (pack of 3)

£141.64

WHSMT-B10025

Metro/General 25mm thickness
insulation board, EPS 100, 2.4m x
1.2m (pack of 12)

£108.86

WHSMT-B10050

Metro/General 50mm thickness
insulation board, EPS 100, 2.4m x
1.2m (pack of 6)

£109.07

WHSMT-B10075

Metro/General 75mm thickness
insulation board, EPS 100, 2.4m x
1.2m (pack of 4)

£109.00

WHSMT-B10100

Metro/General 100mm thickness
insulation board, EPS 100, 2.4m x
1.2m (pack of 3)

£108.96

WHSMT-B10025+

Metro/General 25mm thickness insulation board, EPS 100, 2.4m x 1.2m
Premium range (pack of 12)

£206.14

WHSMT-B10050+

Metro/General 50mm thickness insulation board, EPS 100, 2.4m x 1.2m
Premium range (pack of 6)

£205.93

WHSMT-B10075+

Metro/General 75mm thickness insulation board, EPS 100, 2.4m x 1.2m
Premium range (pack of 4)

£206.00

WHSMT-B10100+

Metro/General 100mm thickness
insulation board, EPS 100, 2.4m x
1.2m Premium range (pack of 3)

£205.93

(Excl. VAT)

RRP

PACK
QTY

£14.00

CODE

DESCRIPTION

WHSMT-B07025

NEXXA CASTELLATED SYSTEM

CODE

DESCRIPTION

WHS-TLALU10

Nexxa System plate with 10mm
Insulation

Call us now 0845 345 2288 or visit www.warmup.co.uk

CLYPSO INSULATION GRIDDED BOARD
(Excl. VAT)

RRP

PACK
QTY

Clypso 25mm Insulation Gridded
PIR board

£52.79

WHS-CL-RB40

Clypso 40mm Insulation Gridded
PIR board

£66.21

WHS-CL-RB50

Clypso 50mm Insulation Gridded
PIR board

£77.89

WHS-CL-RB60

Clypso 60mm Insulation Gridded
PIR board

£86.07

WHS-CL-RB75

Clypso 75mm Insulation Gridded
PIR Board

£100.00

(Excl. VAT)

RRP

PACK
QTY

CODE

DESCRIPTION

WHS-CL-RB25

METRO / GENERAL INSULATION PIR
CODE

DESCRIPTION

WHS-MTINS25

Metro/General 25mm Insulation PIR
- 2.4 x 1.2m

£36.36

WHS-MTINS30

Metro/General 30mm Insulation PIR
- 2.4 x 1.2m

£41.07

WHS-MTINS35

Metro/General 35mm Insulation PIR
- 2.4 x 1.2m

£43.46

WHS-MTINS40

Metro/General 40mm Insulation PIR
- 2.4 x 1.2m

£47.07

WHS-MTINS45

Metro/General 45mm Insulation PIR
- 2.4 x 1.2m

£53.00

WHS-MTINS50

Metro/General 50mm Insulation PIR
- 2.4 x 1.2m

£57.71

WHS-MTINS60

Metro/General 60mm Insulation PIR
- 2.4 x 1.2m

£68.93

WHS-MTINS65

Metro/General 65mm Insulation PIR
- 2.4 x 1.2m

£74.64

WHS-MTINS70

Metro/General 70mm Insulation PIR
- 2.4 x 1.2m

£80.79

WHS-MTINS75

Metro/General 75mm Insulation PIR
- 2.4 x 1.2m

£81.61

WHS-MTINS80

Metro/General 80mm Insulation PIR
- 2.4 x 1.2m

£87.71

WHS-MTINS90

Metro/General 90mm Insulation PIR
- 2.4 x 1.2m

£98.07

WHS-MTINS100

Metro/General 100mm Insulation
PIR - 2.4 x 1.2m

£108.50

The world’s best-selling floor heating brand

TOTAL-16 LOW PROFILE SYSTEM
(Excl. VAT)

RRP

PACK
QTY

£39.99

(Excl. VAT)

RRP

PACK
QTY

£6.66

(Excl. VAT)

RRP

PACK
QTY

£6.66

(Excl. VAT)

RRP

PACK
QTY

Pipes Range - Pipe Pex-A
12mm x 2mm. Sold in lengths
of 70m

£133.67

Pipes Range - Pipe Pex-A
12mm x 2mm. Sold in lengths
of 140m

£267.84

(Excl. VAT)

RRP

PACK
QTY

£105.93

(Excl. VAT)

RRP

PACK
QTY

£5

(Excl. VAT)

RRP

PACK
QTY

£2

(Excl. VAT)

RRP

PACK
QTY

£32

CODE

DESCRIPTION

WHS-TOTAL16BOARD

Total-16 Moulded Straight Board
including Aluminium plate for
Pex-A 12mm pipes.
600 x 1200 x 16mm

CODE

DESCRIPTION

WHS-TOTAL16RETURN

Total-16 Moulded Return Board
for Pex-A 12mm pipes.
300 x 600 x 16mm

CODE

DESCRIPTION

WHS-TOTAL16FEED

Total-16 Moulded Feeding Board
for Pex-A 12mm Pipes.
300 x 600 x 16mm

CODE

DESCRIPTION

WHS-P-PEXA12 X 70
WHS-P-PEXA12 X140

WATER BASED GLUE
CODE

DESCRIPTION

WHS-X-Glue

10 Litre Water-based glue

EUROCONE CONNECTORS
CODE

DESCRIPTION

WHS-PCONNECT12

12mm x 2mm eurocone connectors

PIPE BEND SUPPORT FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

WHS-PBEND12

Pipe bend support for 12mm pipes

DUAL OVERLAY CONCRETE

CODE

DESCRIPTION

WDOC

Dual Overlay Concrete System
(covers 0.72m²)

Call us now 0845 345 2288 or visit www.warmup.co.uk

CONTURA FLOATING PANEL - WITH RETURNS
(Excl. VAT)

RRP

PACK
QTY

Contura Floating 30mm Panel 200mm Centres With Returns 150 Grade

£16.36

WHSCO-P2040

Contura Floating 40mm Panel 200mm Centres With Returns 150 Grade

£21.79

WHSCO-P2050

Contura Floating 50mm Panel 200mm Centres With Returns 150 Grade

£27.25

WHSCO-P2060

Contura Floating 60mm Panel 200mm Centres With Returns 150 Grade

£26.14

WHSCO-P2070

Contura Floating 70mm Panel 200mm Centres With Returns 150 Grade

£30.50

WHSCO-P2080

Contura Floating 80mm Panel 200mm Centres With Returns 150 Grade

£34.86

WHSCO-P2090

Contura Floating 90mm Panel 200mm Centres With Returns 150 Grade

£39.25

WHSCO-P2100

Contura Floating 100mm Panel 200mm Centres With Returns 150 Grade

£43.61

(Excl. VAT)

RRP

PACK
QTY

CODE

DESCRIPTION

WHSCO-P2030

ECONNA OVER JOIST FLOATING PANEL
CODE

DESCRIPTION

WHS-ECCB22A

Econna Over Joist straight contour
board - 600x1800x22

£38.86

WHS-ECCB22AE

Econna Over Joist turn - 800 x 595
x 22mm

£22.36

(Excl. VAT)

RRP

PACK
QTY

£62.21

5 LITRES OF FIX BINDER
CODE

DESCRIPTION

WHS-X-BIND

5 litres of fix binder

3 LITRES OF START PRIMER
CODE

DESCRIPTION

WHS-XPRIMER

3 litres of start primer

(Excl.VAT)

RRP

PACK
QTY

£62.21

20KG PACK OF SEAL ADHESIVE
CODE

DESCRIPTION

WHS-XSEAL25

20kg pack of seal adhesive

The world’s best-selling floor heating brand

(Excl. VAT)

RRP

PACK
QTY

£69.11

Aluminium Diffuser Plates
DIFFUSION PLATE 390 X 1000 X 0.5 / 0.6 / 0.7 MM
TWO GROOVE PLATES (16MM PIPE)
(Excl. VAT)

RRP

PACK
QTY

Diffusion plate 390 x 1000 x 0.5mm
two groove plates (16mm pipe)

£8.75

WHS-TEALUDP2

Diffusion plate 390 x 1000 x 0.6mm
two groove plates (16mm pipe)

£10.36

WHS-TEALUDP3

Diffusion plate 390 x 1000 x 0.7mm
two groove plates (16mm pipe)

£11.79

CODE

DESCRIPTION

WHS-TEALUDP1

DIFFUSION PLATE 190 X 1000 X 0.6 / 0.7 MM PLATES
(16MM PIPE)
(Excl. VAT)

RRP

PACK
QTY

Diffusion plate 190 x 1000 x 0.6mm
plates (16mm pipe)

£4.68

Diffusion plate 190 x 1000 x 0.7mm
plates (16mm pipe)

£5.43

CODE

DESCRIPTION

WHS-TEALUDP4
WHS-TEALUDP5

Fixing & Ancillaries
TACKER GUN TO BE USED WITH TACKER CLIPS
CODE

DESCRIPTION

WHS-CL-FIXER

Tacker gun to be used with tacker
clips)

(Excl. VAT)

RRP

PACK
QTY

£223.21

(Excl. VAT)

RRP

PACK
QTY

£7.11

(Excl. VAT)

RRP

PACK
QTY

£10.39

(Excl. VAT)

RRP

PACK
QTY

£314.79

(Excl. VAT)

RRP

PACK
QTY

£1.88

PIPE CUTTERS UP TO 25MM PIPE DIAMETER
CODE

DESCRIPTION

WHS-P-CUT25

Pipe Cutters up to 25mm pipe
diameter

PIPE CUTTERS UP TO 36MM PIPE DIAMETER
CODE

DESCRIPTION

WHS-P-CUT36

Pipe cutters up to 36mm pipe
diameter

PIPE DECOILER
CODE

DESCRIPTION

WHS-PDECOILER

Pipe decoiler

CALIBRATION TOOL

CODE

DESCRIPTION

WHS-P-FORM

Calibration tool

Call us now 0845 345 2288 or visit www.warmup.co.uk

PIPE BEND SUPPORT FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

WHS-P-BEND

Pipe bend support for hydronic
systems

(Excl. VAT)

RRP

PACK
QTY

£1.48

45/100MM SINGLE CLIPS (100 PER BAG)
FOR HYDRONIC SYSTEMS
(Excl. VAT)

RRP

PACK
QTY

45mm single clips (100 per bag) for
hydronic systems

£4.93

100

65mm single clips (100 per bag) for
hydronic systems

£6.71

100

(Excl. VAT)

RRP

PACK
QTY

£70.71

CODE

DESCRIPTION

WHS-CL-P45
WHS-CL-P65

25MM PIPE CONDUIT PROTECTION 50M
CODE

DESCRIPTION

WHS-CLCONDUIT

25mm pipe conduit protection 50m
for hydronic systems

40 & 60MM CLYPSO CLIPS FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

(Excl. VAT)

RRP

PACK
QTY

WHS-CL-T40

40mm tacker clips (300 per box)

£16.86

300

WHS-CL-T60

60mm Clypso clips (300 per box) for
hydronic systems

£10.46

300

TIES FOR MESH SYSTEM TO HOLD PIPE TO MESH (CABLE TIES)
CODE

DESCRIPTION

WHS-FO-TIE

Ties for Mesh system to hold pipe to
mesh (cable ties) - 100/bag

(Excl. VAT)

RRP

PACK
QTY

£1.39

100

CLIPRAIL FOR HYDRONIC SYSTEMS (SOLD PER UNIT)
CODE

DESCRIPTION

WHS-MTRAIL01

Cliprail for hydronic systems (sold
per unit)

(Excl. VAT)

RRP

PACK
QTY

£2.03

(Excl. VAT)

RRP

PACK
QTY

£9.39

100

(Excl. VAT)

RRP

PACK
QTY

£35.71

NAIL CLIP 16MM FOR JOISTS (100 PER BOX)
CODE

DESCRIPTION

WHS-SI-N16

Nail clip 16mm for joists (100 per
box)

PERIMETER STRIP FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

WHS-XEDGE50

Perimeter strip for hydronic systems
(8mm x 150mm x 50m)

The world’s best-selling floor heating brand

POLYTHENE DPM FOR HYDRONIC SYSTEMS
(Excl. VAT)

RRP

PACK
QTY

Polythene dpm 500g (4m x 50m)

£68.57

Polythene dpm 1200g (4m x 25m)

£81.61

CODE

DESCRIPTION

WHS-XPOL500
WHS-XPOL1200

CABINETS
(Excl. VAT)

RRP

PACK
QTY

Manifold Cabinet 400/640/130mm

£69.88

WHSCabinet450

Manifold Cabinet 450/640/130mm

£71.76

WHSCabinet530

Manifold Cabinet 530/640/130mm

£79.26

WHSCabinet680

Manifold Cabinet 680/640/130mm

£91.58

WHSCabinet830

Manifold Cabinet 830/640/130mm

£104.32

WHSCabinet1030

Manifold Cabinet 1030/640/130mm

£116.64

WHSCabinet1130

Manifold Cabinet 1130/640/130mm

£124.97

(Excl. VAT)

RRP

PACK
QTY

CODE

DESCRIPTION

WHSCabinet400

Steel Manifolds / Ancillaries

STEEL MANIFOLD WITH VALVES AND END SETS

CODE

DESCRIPTION

WHS-M-S-02

2 circuit stainless steel manifold
with ball valves and end sets

£128.93

WHS-M-S-03

3 circuit stainless steel manifold
with ball valves and end sets

£150.89

WHS-M-S-04

4 circuit stainless steel manifold
with ball valves and end sets

£171.14

WHS-M-S-05

5 circuit stainless steel manifold
with ball valves and end sets

£192.18

WHS-M-S-06

6 circuit stainless steel manifold
with ball valves and end sets

£215.18

WHS-M-S-07

7 circuit stainless steel manifold
with ball valves and end sets

£236.11

WHS-M-S-08

8 circuit stainless steel manifold
with ball valves and end sets

£257.14

WHS-M-S-09

9 circuit stainless steel manifold
with ball valves and end sets

£285.25

WHS-M-S-10

10 circuit stainless steel manifold
with ball valves and end sets

£301.32

WHS-M-S-11

11 circuit stainless steel manifold
with ball valves and end sets

£319.79

WHS-M-S-12

12 circuit stainless steel manifold
with ball valves and end sets

£343.57

Call us now 0845 345 2288 or visit www.warmup.co.uk

AUTO AIR VENT
CODE

DESCRIPTION

WHS-M-BVENT

Auto Air Vent for Hydronic System

(Excl. VAT)

RRP

PACK
QTY

£6.07

(Excl. VAT)

RRP

PACK
QTY

£428.57

A RATED MANIFOLD PACK /
ZONE MANIFOLD WITH PUMP / MIXING UNIT
CODE

DESCRIPTION

WHS-M-SRM02

A Rated Manifold Pack / Zone Manifold with Pump / Mixing unit

REPLACEMENT FLOWMETER FOR STAINLESS STEEL MANIFOLD
CODE

DESCRIPTION

WHS-M-SFLOW

Replacement flowmeter for stainless
steel manifold

(Excl. VAT)

RRP

PACK
QTY

£7.50

PRESSURE GAUGE WITH BUSH FOR USE WITH WHS-M-S-PUMP
CODE

DESCRIPTION

WHS-M-SFLOWB

Pressure Gauge with Bush for use
with WHS-M-S-PUMP

(Excl. VAT)

RRP

PACK
QTY

£12.14

(Excl. VAT)

RRP

PACK
QTY

Brass Manifolds & Ancillaries
BRASS MANIFOLD
CODE

DESCRIPTION

WHS-C-DCCT02

2 zone brass manifold

£86.36

WHS-C-DCCT03

3 zone brass manifold

£107.68

WHS-C-DCCT04

4 zone brass manifold

£123.29

WHS-C-DCCT05

5 zone brass manifold

£147.54

WHS-C-DCCT06

6 zone brass manifold

£167.07

WHS-C-DCCT07

7 zone brass manifold

£186.75

WHS-C-DCCT08

8 zone brass manifold

£209.71

WHS-C-DCCT09

9 zone brass manifold

£244.00

WHS-C-DCCT10

10 zone brass manifold

£276.07

WHS-C-DCCT11

11 zone brass manifold

£300.57

WHS-C-DCCT12

12 zone brass manifold

£315.39

The world’s best-selling floor heating brand

“A” RATED GRUNDFOS PUMP
CODE

DESCRIPTION

RRP
EXC
RRP
(Excl.
VAT)
VAT

PACK
QTY

WHS – PUMP
“A” RATED

“A” rated
grundfos
pump
“A” rated
pump

£302.00
£232.14

(Excl. VAT)

RRP

PACK
QTY

£29.29

QUATTRO END SET FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

WHS-M-BENDSET

Quattro end set for hydronic systems

QUATTRO END SET WITH MANUAL VENT AND MANOMETER
CODE

DESCRIPTION

WHS-M-BENDSETVENT

Quattro End set with manual vent
and manometer

(Excl. VAT)

RRP

PACK
QTY

£72.36

(Excl. VAT)

RRP

PACK
QTY

£74.57

MANIFOLD EXTENSION KIT
CODE

DESCRIPTION

WHS-M-B-EXT

Manifold extension kit

REPLACEMENT FLOWMETER FOR BRASS MANIFOLD
CODE

DESCRIPTION

WHS-M-BFLOW

Replacement flowmeter for brass
manifold

(Excl. VAT)

RRP

PACK
QTY

£11.61

A RATED ISOTHERM PUMP/MIXER KIT
CODE

DESCRIPTION

WHS-M-BPUMP “A”
Rated (New)

A Rated Isotherm pump/mixer kit

(Excl. VAT)

RRP

PACK
QTY

£536.14

(Excl. VAT)

RRP

PACK
QTY

£28.64

BALL VALVE SET 1” FOR HYDRONIC SYSTEMS
CODE

DESCRIPTION

WHS-M-BVALVE

Ball valve set 1” for hydronic systems

MANIFOLD BALL VALVE SET WITH THERMOMETERS
CODE

DESCRIPTION

WHS-M-BVALVE-T

Manifold ball valve set with thermometers for hydronic systems

(Excl. VAT)

RRP

PACK
QTY

£59.29

(Excl. VAT)

RRP

PACK
QTY

£1.79

BLANKING CAP FOR CLOSING OFF A MANIFOLD

CODE

DESCRIPTION

WHS-M-BCAP

Blanking cap for Stainless Steel manifolds. Closes off individual circuits

Call us now 0845 345 2288 or visit www.warmup.co.uk

Manifold Ancillaries & Fittings
230 V / 24 V ACTUATOR FOR HYDRONIC SYSTEMS
(Excl. VAT)

RRP

PACK
QTY

230v Actuator for hydronic systems

£19.89

24v actuator for hydronic systems

£23.54

(Excl. VAT)

RRP

PACK
QTY

£25.21

(Excl. VAT)

RRP

PACK
QTY

£62.50

(Excl. VAT)

RRP

PACK
QTY

£2.36

(Excl. VAT)

RRP

PACK
QTY

CODE

DESCRIPTION

WHS-S-230AC
WHS-S-24AC

230V ACTUATOR WITH LED
CODE

DESCRIPTION

WHS-C-D-CCT230ACL

230V Actuator with LED

22MM 2 PORT VALVE FOR ZONING
OF MANIFOLDS AND HEATING SYSTEMS
CODE

DESCRIPTION

WHS – ZONE
VALVE 2 PORT

22mm 2 port valve for zoning of
manifolds and heating systems

MONOBLOCCOS CONNECTOR
CODE

DESCRIPTION

WHS-P24x19
connector

monobloccos connector

MONOBLOCCOS 16/12MM PIPE ADAPTER
CODE

DESCRIPTION

WHS-P-16 x
2Monoblocco

monobloccos 16mm pipe adapter

£4.33

WHS-P-12 x
2Monoblocco

Monobloccos 12mm Pipe Adapter

£4.86

(Excl. VAT)

RRP

PACK
QTY

£2.50

(Excl. VAT)

RRP

PACK
QTY

EUROCONE CONNECTORS
CODE

DESCRIPTION

WHS-PCONNECT

16mm x 2mm eurocone connectors
for hydronic systems

REPAIR CONNECTORS
CODE

DESCRIPTION

WHS-P-RC16

16 x 2mm repair connector

£6.50

WHS-P-RC20

20 x 2mm repair connector

£6.50

(Excl. VAT)

RRP

PACK
QTY

£10.11

THREADED SOCKET (MALE)
CODE

DESCRIPTION

WHS-PSOCKET

Threaded socket (male)

The world’s best-selling floor heating brand

Pipes

WARMUP PEX-A PIPE 16MM X 2MM
CODE

DESCRIPTION

(Excl. VAT)

RRP

PACK
QTY

WHS-P-PEXA-25

PEX-A 16mm x 2mm x 25m

£32.61

WHS-P-PEXA-50

PEX-A 16mm x 2mm x 50m

£65.22

WHS-P-PEXA-60

PEX-A 16mm x 2mm x 60m

£78.27

WHS-P-PEXA70

PEX-A 16mm x 2mm x 70m

£91.31

WHS-P-PEXA-80

PEX-A 16mm x 2mm x 80m

£104.36

WHS-P-PEXA-90

PEX-A 16mm x 2mm x 90m

£117.40

WHS-P-PEXA-100

PEX-A 16mm x 2mm x 100m

£130.45

WHS-P-PEXA-110

PEX-A 16mm x 2mm x 110m

£143.49

WHS-P-PEXA120

PEX-A 16mm x 2mm x 120m

£156.54

WHS-P-PEXA200

PEX-A 16mm x 2mm x 200m

£382.44

WHS-P-PEXA-300

PEX-A 16mm x 2mm x 300m

£573.48

WHS-P-PEXA-500

PEX-A 16mm x 2mm x 500m

£652.23

(Excl. VAT)

RRP

PACK
QTY

WARMUP PE-RT PIPE 16MM X 2MM
CODE

DESCRIPTION

WHS-P-PERT-25

PE-RT 16mm x 2mm x 25m

£23.68

WHS-P-PERT-50

PE-RT 16mm x 2mm x 50m

£47.37

WHS-P-PERT-60

PE-RT 16mm x 2mm x 60m

£56.84

WHS-P-PERT-70

PE-RT 16mm x 2mm x 70m

£66.31

WHS-P-PERT-80

PE-RT 16mm x 2mm x 80m

£75.79

WHS-P-PERT-90

PE-RT 16mm x 2mm x 90m

£85.26

WHS-P-PERT-100

PE-RT 16mm x 2mm x 100m

£94.73

WHS-P-PERT-110

PE-RT 16mm x 2mm x 110m

£104.21

WHS-P-PERT-120

PE-RT 16mm x 2mm x 125m

£113.68

WHS-P-PERT-300

PE-RT 16mm x 2mm x 300m

£305.63

WHS-P-PERT-500

PE-RT 16mm x 2mm x 500m

£473.66

(Excl. VAT)

RRP

PACK
QTY

WARMUP PE-RT/AL/PE-RT 16MM X 2MM
CODE

DESCRIPTION

WHS-P-ALPERT-100

ALPERT 16mm x 2mm, 100m

£153.60

WHS-P-ALPERT-200

ALPERT 16mm x 2mm, 200m

£307.14

WHS-P-ALPERT-500

ALPERT 16mm x 2mm, 500m

£767.86

Call us now 0845 345 2288 or visit www.warmup.co.uk

Projects Department: A Dedicated
Service
Warmup offers a dedicated team of Project Managers to help
you throughout each stage of your project by allocating a
dedicated Project Manager to support you from specifying and
fitting, through to pre and post-installation.

Our Approach

•

Upon receipt of your instructions and/or plans you will be
assigned a dedicated in-house Project Manager

•

Your Project Manager will contact you to review your
project to ensure we have a complete understanding of
your needs and the issues affecting your project

•

Upon receipt of all relevant project information including
details of floor build up and final floor surface, a quotation
will be turned around within 24 hours. Complex projects
will take longer

•

Where appropriate we will provide advice, guidance and
support both on and off-site where potential risks can be
identified and prevented

•

Provide the highest quality of products and services that
is tailored to meet your specific requirements, adhering to
best practice at the right price and at the right time

The world’s best-selling floor heating brand

Design Process
Warmup products and solutions adhere to industry standards,
government legislation and Building Regulations. The project
team, led by your dedicated Project Manager, will always
recommend the best underfloor heating solution for your
project, mindful of the need to keep to your specification, time
schedule and budget.
Warmup will provide complete layouts to ensure there is a
precise installation and zone control to the required area.
Our products can be included from the RIBA Stage C – Concept
Design. It is at this stage that the Warmup project design
team incorporates the development of the general layout, the
external envelope and the principals from the project brief.
Outline costs can be provided at this stage for project budgets.
As the project develops into Stage D, the Detailed Design,
Warmup products, technical and specific design details can be
incorporated. Working in collaboration with you, we will ensure
co-ordination with the layouts and any integrated interior
designs.

Warmup provides quality products and services
and will:

•
•
•

Only promise what we can deliver
Deliver on what we promise
Always remember that the products and services offered
and installed by Warmup stand for quality

We are committed to providing an excellent level
of service and aim to deliver this by:

•

Focusing on your needs when recommending solutions,
planning and delivering services

•

Applying the same standard of customer care to all
our customers, whilst recognising that customers have
individual needs

The following standards indicate the minimum
level of service customers can expect when
dealing with Warmup

•

Requests for quotations will be sent an automatic
response acknowledging your request

•

We will give you the name of the dedicated Project
Manager who has been assigned your enquiry and we will
give you an indication of when you can expect to receive
a response

Call us now 0845 034 8270 or visit www.warmup.co.uk

•

Should you request us to contact you via telephone, we will
agree with you the best time to do so

Every Warmup quotation will include a detailed
summary of the project in which we will break
down:

•
•
•

The total gross and heated areas
The total heat load and amperage required
A detailed list of the items required with relevant technical
data supported by illustrations of every item specified,
including the controls and details of the supporting
Guarantees and Warranties

Once we have been awarded the contract and/or purchase order,
your dedicated Project Manager will continue to work closely
with you to see your project through to a successful conclusion.

Technical Support
We will support you pre and post sales/installation by offering
you telephone support.
We offer online ‘live’ chat between 08.00 and 17.30 hrs Monday
to Friday. This is in addition to installation manuals and access to
online tutorial videos.
We offer a SafetyNetTM Installation Guarantee. Should you (or
your installer) accidentally damage a heating system (wire or
pipe) during installation, we will replace it free of charge.
If a floor(s) is damaged post installation (i.e. by drilling through a
pipe or wire), we offer a dedicated team of service engineers.

For more information or to submit plans please
call: 0845 034 8270, email: projects@warmup.com,
fax: 0845 345 2299 or visit www.warmup.co.uk.

The world’s best-selling floor heating brand

Electric and hydronic heating portfolio

The world’s best-selling floor heating brand™

Over 2 million installations in
more than 60 countries

Total-16
Low Profile System
Hydronic Insulation System

“ideal for new-build and refurbishment projects
where floor height is at a premium”

Warmup Plc
702 & 704 Tudor Estate
Abbey Road
London, NW10 7UW

T: 0845 345 2288
E : uk@warmup.com
E: dispatch@warmup.com
F: 0845 345 2299
W: www.warmup.co.uk
Please scan the QR code
for more information

The WARMUP word and associated logos are trade marks.
©Warmup plc 2015 Reg’d. TM Nos. 1257724, 4409934, 4409926, 5265707. E & OE
v07-09/2015

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract
Create Date                     : 2015:09:30 13:41:38+01:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2015:09:30 13:43:41+01:00
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Metadata Date                   : 2015:09:30 13:43:41+01:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:0d69b51c-88b6-4f88-b793-23caec4e6d92
Original Document ID            : xmp.did:C8E5BBDE01B3E2119FDDA752B50FD3F8
Document ID                     : xmp.id:D6860F8C6767E511A210A890BFAB866B
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:EA0DE82CCF61E511803BFBAF178B0B16
Derived From Document ID        : xmp.did:EA0DE82CCF61E511803BFBAF178B0B16
Derived From Original Document ID: xmp.did:C8E5BBDE01B3E2119FDDA752B50FD3F8
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2015:09:30 13:41:38+01:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 100

EXIF Metadata provided by EXIF.tools

Warmup Trade Brochure

Navigation menu

Versions of this User Manual:

Views

Navigation