CRT3452 XDVM8357
User Manual: XDVM8357
Open the PDF directly: View PDF 
.
Page Count: 118
| Download | |
| Open PDF In Browser | View PDF |
ORDER NO.
CRT3452
LX470
LAND CRUISER 100
AUDIO SYSTEM
DVD/CD COMPATIBLE
CHANGER
VEHICLE
LEXUS LX470,
LAND CRUISER
100
DESTINATION
U.S.A., CANADA, GUAM,
PUERTO RICO, BRAZIL
Manufactured for TOYOTA
by PIONEER CORPORATION
PRODUCED
AFTER
May 2005
OEM PARTS No.
86270-60114
ID No.
•••••
PIONEER MODEL No.
XDV-M8357ZT/UC,
XDV-M8357ZT-91/UC
PUB.NO.CRT3452
1
2
3
4
A
Notes
CD-Rs may not
be playable in
this compact
disc player.
B
This service manual should be used together with the following manual(s):
Model No.
Order No.
Mech. Module
Remarks
CX-692
CRT2533
MM-1
DVD/CD Mech. Unit : Circuit Description, Mech. Description, Disassembly
C
XDV-M8357ZT/UC and XDV-M8357ZT-91/UC have adopted AVC-LAN.
Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks
of Dolby Laboratories.
For details, refer to "Important Check Points for Good Servicing".
D
The supplementary models are identical with the original ones except for the following items.
* : Non spare part
E
Description
Polyethylene Bag
* Air Cap
Carton
Contain Box(x1/2)
Protector
XDV-M8357ZT-91/UC
CEG1181(Unit)
CEG1288(Connector)
CHG4170
CHL5166
CHP2341(TOP)
Protector
CHP2342(BOTTOM)
F
2
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
SAFETY INFORMATION
CAUTION
A
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of
California to cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
B
- DVD Player Service Precautions
1. You should conform to the regulations governing the
product (safety, radio and noise, and other regulations),
and should keep the safety during servicing by following
the safety instructions described in this manual.
2. Never adjust the LD VR in the pickup unit to protect
the pickup from electrical damages.
3. For pickup unit(CGY2020) handling, please refer to
"Disassembly".
During replacement, handling precautions shall be
taken to prevent an electrostatic discharge(set the short
switch of the pickup unit to the SHORT side).
4. During disassembly, be sure to turn the power off since
an internal IC might be destroyed when a connector
is plugged or unplugged.
5. Please adjusting the skew after changing the pickup
unit.
C
D
E
is a trademark of DVD Format/Logo Licensing Corporation.
F
XDV-M8357ZT/UC
5
6
7
8
3
1
2
3
4
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
A
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
B
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
C
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
0 Safe environment should be secured during servicing.
D
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
E
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
F
4
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
CONTENTS
SAFETY INFORMATION......................................................................................................................................3
1. SPECIFICATIONS .............................................................................................................................................6
2. EXPLODED VIEWS AND PARTS LIST.............................................................................................................8
2.1 EXTERIOR .................................................................................................................................................8
2.2 DVD/CD MECHANISM UNIT....................................................................................................................10
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................12
3.1 BLOCK DIAGRAM....................................................................................................................................12
3.2 DVD/CD MECHANISM UNIT, MAIN PCB(SERVO SECTION)(GUIDE PAGE) .........................................16
3.3 MAIN PCB(DECODER SECTION)(GUIDE PAGE)...................................................................................26
3.4 EXTENSION UNIT....................................................................................................................................32
3.5 KEYBOARD PCB .....................................................................................................................................38
3.6 MF UNIT ...................................................................................................................................................39
4. PCB CONNECTION DIAGRAM ......................................................................................................................40
4.1 MAIN PCB ................................................................................................................................................40
4.2 EXTENSION UNIT....................................................................................................................................44
4.3 KEYBOARD PCB .....................................................................................................................................48
4.4 MF UNIT ...................................................................................................................................................49
4.5 DVD/CD MECHANISM UNIT....................................................................................................................50
5. ELECTRICAL PARTS LIST .............................................................................................................................54
6. ADJUSTMENT ................................................................................................................................................65
6.1 JIG CONNECTION DIAGRAM .................................................................................................................65
6.2 MAIN UNIT ADJUSTMENT ......................................................................................................................67
6.3 SKEW ADJUSTMENT ..............................................................................................................................68
6.4 ELEVATION ADJUSTMENT .....................................................................................................................70
6.5 TEST MODE .............................................................................................................................................74
7. GENERAL INFORMATION .............................................................................................................................92
7.1 DIAGNOSIS..............................................................................................................................................92
7.1.1 DISASSEMBLY......................................................................................................................................92
7.1.2 CONNECTOR FUNCTION DESCRIPTION ..........................................................................................95
7.2 IC ..............................................................................................................................................................96
7.3 EXPLANATION .......................................................................................................................................115
7.3.1 OPERATIONAL FLOW CHART ...........................................................................................................115
7.3.2 SYSTEM BLOCK DIAGRAM ...............................................................................................................116
8. OPERATIONS ...............................................................................................................................................117
A
B
C
D
E
F
XDV-M8357ZT/UC
5
6
7
8
5
1
2
3
4
1. SPECIFICATIONS
A
B
General
Player
System .................................... DVD-Video, Video CD,
Compact disc audio system
Usable discs .... DVD-Video, Video CD, Compact disc
Signal format
1.Linear PCM
.................... Sampling frequency: 44.1/48/96 kHz
Number of quantization bits: 16/20/24; linear
2.Dolby digital
3.MPEG
Power source ...... 13.2 V DC (10.5 – 16.1 V allowable)
Grounding system .................................. Negative type
Rated current ................ 1.0 A or less(DVD regenerate)
Region Number
.............................................................................. 1
Backup current ...........................................5mA or less
Weight ................................................................ 2660 g
Video
Output level .......................... 1000 mVp-p±0.2 V/75 Ω
Audio
Frequency response .................... ±1.5dB(20Hz,20kHz)
Signal-to-noise ratio
.......................................................... 80dB or more
Residual distortion .................................... 0.1% or less
Output Level ............................ 1000 mV (1 kHz, 0 dB)
Number of channels ...................................... 2 (stereo)
Max. output power supply ..........................2Vrms±2dB
Separation..................................................65dB or more
The difference between right output and left output
............................................................1.5dB or less
C
D
E
F
6
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
A
B
C
D
E
F
XDV-M8357ZT/UC
5
6
7
8
7
1
2
3
4
2. EXPLODED VIEWS AND PARTS LIST
NOTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
• The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
• Screw adjacent to mark on the product are used for disassembly.
• For the applying amount of lobricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.)
A
"
2.1 EXTERIOR
B
C
D
E
F
8
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
EXTERIOR SECTION PARTS LIST
Mark No.
*
*
Description
Mark No.
Part No.
1
2
3
4
5
Screw
Screw(M2x4)
Screw(M3x12)
Screw(M2x3.5)
Spring
BSZ30P055FTC
CBA1676
CBA1819
CBA1966
CBH2335
6
7
8
9
10
Connector
Cord Assy
Clamper
Clamper
Upper Case
CDE6302
CDE6983
CNV7278
CNV7279
CNB2496
11
12
13
14
15
Holder
Bracket
Bracket
Shield
Insulator
CNC8612
CNC8831
CNC8832
CNC9089
CNM6337
16
17
18
19
20
Insulator
Filter
Insulator
Cushion
Insulator
CNM6405
CNM6600
CNM6735
CNM6743
CNM6906
21
22
23
24
25
Insulator
Cushion
Insulator
Cushion
Cushion
CNM6985
CNM7037
CNM7090
CNM7347
CNM7872
26
27
28
29
30
PCB
PCB
PCB
Panel
Damper
CNP5534
CNP5535
CNP5604
CNS8228
CNV5833
31
32
33
34
35
Holder
Holder
MF Unit
Plug(CN2903)
Connector(CN2901)
CNV6181
CNV8121
CWM6518
CKS1051
CKS3563
36
37
38
39
40
Holder
Shield
Insulator
Main Unit
Terminal(CN1603)
CNC2218
CNC8898
CNM6836
CWX3187
CKF1064
41
42
43
44
45
Terminal(CN1604)
Terminal(CN1605)
Terminal(CN1607)
Connector(CN1601)
Connector(CN101)
CKF1064
CKF1064
CKF1064
CKS1953
CKS1964
46
47
48
49
50
Connector(CN312)
Connector(CN2000)
Connector(CN302)
Connector(CN1600)
Connector(CN310)
CKS2191
CKS2193
CKS3480
CKS3749
CKS3767
51
52
53
54
Connector(CN301)
Connector(CN1000)
Extension Unit
Screw
CKS4358
CKS4374
CWX3198
BMZ26P050FTC
Description
Part No.
55
Cord
CDE6446
56
57
58
59
60
Terminal(CN3810)
Terminal(CN3811)
Terminal(CN3812)
Terminal(CN3813)
Connector(CN3951)
CKF1064
CKF1064
CKF1064
CKF1064
CKS1953
61
62
63
64
65
Connector(CN3891)
Connector(CN3301)
Connector(CN3302)
Plug(CN3802)
Connector(CN3961)
CKS2191
CKS2619
CKS2619
CKS3535
CKS3749
66
67
68
69
70
Connector(CN3801)
Connector(CN3803)
Holder
Shield
Shield
CKS4320
CKS4356
CNC8400
CNC8899
CNC8900
71
72
73
74
75
Insulator
Insulator
Arm Unit
Rear Frame Unit
Lower Case Unit
CNM6834
CNM6835
CXA8606
CXB6364
CXB6365
76
77
78
79
80
Button(EJECT)
Door
Spring
Spring
Spring
CAC6152
CAT2385
CBH2336
CBH2337
CBH2363
81
82
83
84
85
Connector
Holder
Holder
Cushion
Cushion
CDE6022
CNC8402
CNC8409
CNM6407
CNM6842
86
87
88
89
90
Cushion
Insulator
Lever
Lever
Damper Unit
CNM6843
CNM6907
CNV5831
CNV6104
CXB4206
91
92
93
94
95
Screw
IMS20P035FTB
Screw
IMS26P040FTC
DVD/CD Mechanism Unit(MM-1)CXK7020
Fan Motor
CXM1195
Grille
CNS6472
96
97
98
99
100
Screw
Screw
Screw
Screw
Tape
6
B
C
D
*
*
101 IC(IC3821)
102 Transistor(Q3811)
E
IMS30P060FTB
ISS30P060FTC
PMB26P050FTC
TMZ50P060FTC
CNM7273
BA00AST
2SB942A
F
XDV-M8357ZT/UC
5
A
7
8
9
1
2
3
4
3
4
2.2 DVD/CD MECHANISM UNIT
A
B
C
D
E
F
10
XDV-M8357ZT/UC
1
2
5
6
7
8
DVD/CD MECHANISM UNIT SECTION PARTS LIST
Description
Screw(M2x4)
Screw(M2x2.5)
Screw(M2x2.5)
Screw(M2x3.5)
Screw(M2x3)
Part No.
CBA1026
CBA1651
CBA1041
CBA1674
CBA1154
Mark No.
66
67
68
69
70
6
7
8
9
10
Screw(M2x2)
Screw(M2x1.4)
Screw(M2x2.2)
Washer
Washer
CBA1243
CBA1687
CBA1965
CBF1002
CBF1037
11
12
13
14
15
Washer
Spring
Spring
Spring
Spring
Mark No.
1
2
3
4
5
*
*
Description
Bearing
Rail
Lever
Guide
Guide
Part No.
CNR1415
CNV4420
CNV4422
CNV4597
CNV4722
71
72
73
74
75
Rack
Guide
Rack
Gear
Gear
CNV4828
CNV5193
CNV5451
CNV5658
CNV5659
CBF1038
CBH2368
CBH1827
CBH1828
CBH1829
76
77
78
79
80
Holder
Holder
Guide
Guide
Rail
CNV5661
CNV5662
CNV5663
CNV5664
CNV5668
Guide
Arm
Arm
Gear
Gear
CNV5671
CNV5868
CNV6158
CNV6226
CNV6242
*
16
17
18
19
20
Spring
Spring
Spring
Spring
Spring
CBH1830
CBH1919
CBH1930
CBH2070
CBH2091
81
82
83
84
85
21
22
23
24
25
Spring
Spring
Spring
Spring
Spring
CBH2159
CBH2227
CBH2238
CBH2279
CBL1307
86
87
88
89
90
Gear
Connector(CN301)
PCB
Damper Unit
Plate Unit
CNV6285
CKS3476
CNX3040
CXA7159
CXB2262
26
27
28
29
30
Spring
Spring
Spring
Spring
Spring
CBL1362
CBL1388
CBL1416
CBL1417
CBL1418
91
92
93
94
95
Lever Unit
Motor Unit(Carriage)(M1)
Screw
Motor Unit(ELV)(M4)
Gear
CXB2266
CXC1552
JFZ20P025FNI
CXC1540
CNV6239
31
32
33
34
35
Spring
Spring
Spring
Connector
PU Unit
CBL1419
CBL1420
CBL1422
CDE6156
CGY2020
96
97
98
99
100
Gear
Bracket Unit
Motor
Screw
Motor Unit(Tray)(M2)
CNV6240
CXB5838
CXM1220
JFZ20P025FNI
CXC1541
36
37
38
39
40
Shaft
Shaft
Shaft
Shaft
Lever
CLA2803
CLA3428
CLA3431
CLA3562
CNC6194
101
102
103
104
105
Screw
Lever Unit
Screw Unit(-D)
Magazine Holder Unit
Frame Unit
JFZ20P025FNI
CXB3933
CXB3934
CXC5000
CXB3970
41
42
43
44
45
Plate
Holder
Lever
Lever
Frame
CNC6847
CNC7448
CNC7975
CNC8065
CNC8068
106
107
108
109
110
Chassis Unit
Chassis Unit
Lever Unit
Arm Unit
Clamper
CXB3972
CXB3975
CXB3976
CXB4318
CNV5667
46
47
48
49
50
Lever
Bracket
Cover
Arm
Arm
CNC8097
CNC8106
CNC8129
CNC8335
CNC8336
111
112
113
114
115
Motor(Spindle)(M3)
Screw
Screw
Gear
Bracket Unit
CXM1282
IMS26P040FMC
JFZ17P020FNI
CNV6225
CXB4003
51
52
53
54
55
Cover
Holder
Cover
Cover
Cover
CNC8347
CNC8476
CNC8921
CNC8922
CNC8923
116
117
118
119
120
Motor
Photo Transistor(Q851)
Bracket Unit
LED(D851)
Resistor(VR301)
CXM1221
PT4800
CXB3971
CN504-2
CCW1021
56
57
58
59
60
Plate
Cover
Cushion
Spacer
Sheet
CNC9010
CNC9083
CNM6301
CNM6334
CNM6385
121
122
123
124
125
Switch(S301)
Capacitor(C301)
Resistor(R301)
Resistor(R302)
Semi-fixed(VR302)
CSN1044
CKSRYB104K16
RS1/16S562J
RS1/16S622J
CCP1338
61
62
63
64
65
Sheet
PCB
PCB
PCB
Ball
CNM6581
CNP5371
CNP5380
CNP5381
CNR1189
126
127
128
129
130
Switch(S852)
Capacitor(C302)
Switch(S851)
Sheet
Screw
CSN1052
CKSRYB103K50
CSN1051
CNM9776
ZMK30H025FZB
5
6
*
*
*
*
*
*
*
XDV-M8357ZT/UC
7
8
A
B
C
D
E
F
11
1
2
3
4
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
A
E
MAIN PCB
27MMC
IPF
DSPCLK
Q103
CN101
B
Q104
45
78LD
16
44
15 78MPD
B1I-B4I
12
11
5
RFA
6
.
.
.
B1I-B4I
Q165
41
RFA
IC103
TA1254AF
IC107
PA0065AM
19 2
IC108(1/2)
NJM3404AM
1
46
IC105
NJM3404AM
1
38
20
6
IC108(2/2)
NJM3404AM
7
41
47
-
VREF
7
VRCK
PSC
SCB
SCL
SCD
FEB
DDC5S
VREF
MOTOR DRIVER
Q102
-
23 F+,F-,T+,T26
20
LD
1
IC101
IR3C07N
IC304
BA6797FM
5
CRG+ 1
CRG- 2
3
MPD
19
TEMP
9
13 1/2SW
5
16
35
13
14
15
34
1
7
IC102
NJM2904M
SCB
SCL
SCD
1
2
FEB
BUCK
/CCE
48
50
D
7
7
6
6
CRG-
IC601
TC4053BFT
IC604, 605
NJM3414AV
DCONT
S852
DSP
S851
TRP
1
4
4
2
2
5
5
1
1
1
1
2
2
3
3
2
9
3
2
9
3
BUCK
/CCE
D
4
Q851
8
4
8
D
TRY+
TRY-
10
12
3
5
9
13
2
6
IC305
LB1836M
M4
SPDL M
MOTOR
6
7
4
1
5
PCB UNIT(A)
2
3
I4
I2
I3
I1
I4
I3
I1
I2
1
GND
1
VR25
IC352
MC33202D
6
1
IC353
MC33202D
2
IC351
TC4S66F
PCB UNIT(B)
IC301
TC4W53F
SPDL
SELECTOR
6
7
95
5
ASTB
XCS
XIRQ
XWR
XRD
57
BUCK
56
XCCE
26
LCDCLK
D
6
TXDQSY
TXDT,TXCLK
85
40
49
20
46
44
IC703
LC89170MP
73
139
140
141
142
143
ASTBM
XMCS
XIRQ2
XMWR
XMRD
ASTB
XMCS
XIRQ2
XMWR
XMRD
75
XSWR
74
XSRD
XWRL
XRD
D0-D7,A0-A7
ASC,AFC
APC
1,5
C
IC204
NJM2100M
7
3
189
DUTY50
12,13
CD SPDL
7
IC206
TC74VHCU04FT
IC303
NJM2904M
IC501
PEG114A
Xin 15
5
X501
10MHz
7
IC203
NJM2100M
81
83
94
86
93
EPVO
MAGSW 18
98
EREF
EVREF
Q203
170
A
DDC5
8
IC1005
MAX662AESA
6
CS23
2
IC1707
TC7SHU04FU
4
ADDRESS DECODER
12
12
A19-A21
FLASH RAM
D0-15
A1-19
2
CS21
IC1003
TC7SHU04FU
4
IC1001
PD6531A
12
IC1004
PD6520A
11
26 XCS22
28
VMCONT
VDCONT
BSENS
SRSENS
FG
HOME
SPCONT
ELVREF
ADENA
ELVPVO
XMAG
Vref
11 VMCONT
82 VDCONT
74
XBSEN
75 XSRSENS
XMRES 12
B
162
XMRES
IC1007
TC74VHC139FT
2
3,13
A20
A21
1,15
XCS20
SDRAM
D0-7
A0-16
30
IC1000
M5M51008DKV-70HI
5
32
XCS2
F
XDV-M8357ZT/UC
2
3
DCAS,DWE
DOE,DRAS
FPWM,VPWM
PPWM,RPWM
DSCSIZ
ADDRESS DECODER
4
10
11
26
28
AIN
DD0-7
XCS23
FLASH RAM
D0-15
A1-19
VRC
RFA
CN1000
4
ATC
Q204
MAGSW
IC1013
TC7SH08FUS1
186
172
GND
2
1
6
DA0-10
7
Q501
VCOCLK
XSDREQ 76 2
SDACK 77
IC702
MSM5117800F-60JS
10
6
181
4
Xout 13
80
I4
79
I2
78
I3
FG
XCS21
1
165
1
MAD0-MAD7
B
ST/SP
4,5
12
XRESET
XSWAIT
C
VD9
DDC5S
IC1706
TC74VHC238FT
E
XSYSRST
XSACK
SREQ
MCDIF
ASIC
DATA,SFSY,SBSY
RST
DRAM
4
EREF
EVREF
EPVO
MAGSW
16 XFMWE
20 CTS
19 DTR
RXD
18
TXD
17
1 VCC
XSACK 55
SREQ 56
DIFOUT 108
4
IC701
PD4995A
XCS2
B
1
2
3
4
5
IC707
TC7SET04FUS1
VR21
FLGA,FLGB,FLGC,FLGD
XRD
S301
1
2
3
4
5
4
2
Q401
Q402
3
3,5
5
XWRL
VR301
MAG
IC
TC7SH
XCS3
XCSLI 72
XIRQ11 103 XIRQL11
XIRQ10 102 XIRQL10
2
IC706
TC7SET08FUS1
FPWM,VPWM
PPWM,RPWM
CN310
VR302
TESIO0 19
TRO
FMO
DMO
87
DSP
95
TRP
92
DISK
DVD SPDL
VD9
CN301
A
BUCK
CCE
MECHANISM
CONTROLLER
EC
ECR
FG
HOME
ST/SP
VM
VCC
SA6 85 4
EXCK
2VREF
TEMP
21
OEIC
5
LDCONT
MOTOR DRIVER
DSP
TRP
DISC
VLED
120
97
ELV+
ELV-
1
TESIO1 67
6 PSC
SCB
2
RFSCB
SCL 100 RFSLC
SCD
1
RFSCD
22
FEB
FEB
3
LCDBIAS
4
LCDTLT
Q601
DDC5S
Q403
50
CD/DVD
84
DCONT
PCB(B)
M2
TRAY M
MOTOR
1
IC704
TC7SET08FUS1 2
VRA
FOO
BUS0-3
CN302
M1
CRG M
MOTOR
91
92
44
PCB(A)
CRG+
4
IC401
TC9461F
43
24
4
9
ELV+
ELV-
8
DDC5S
2
19
9 10 11
C
CLCK
DSP
F JUMP
IC402
NJM2904M
CKCD
C2F1
TEBC
TEI
VR21
VR25
CN312
1
DOUT,LRCK,AOUT
CDBCK
BCK 109
LRCK 110 CDLRCK
ADATAO 111 CDDATA
DXTKI
CDBCK
Q404
C
M3
ELV M
MOTOR
114
107
116
BCK
DDC5S
3
VRD 7
Q168
VSHF
22
2
BCK
XI 73
IPF 6
P1TN
DDC5S
Q101
4
RFI
FEI
SBAD,FLGB,RFCT,RFPR
5
2 CH1,CH2,CH3
4
2
TEO
RF AMP
IC109
TC7WU04FU
FEO 21
RFA
A
IC106
PU UNIT
MDI1
33
RFO 28
LDO1
4
FGPL
IC
TC7SE
5
6
7
8
A
CN1600
IPF
CDBCK
CDLR
CDDATA
5
29
XRESET
XSWAIT
XRES
165
dten
DRQ
int
reset
RS
1
2
XCS23
XRD
XWRL
IC1704
TC7S02FU
5
IC1501
MC33202D
1
5
7
6
IC1503
NJM2068MD
89
XSACK
91
53 SREQ
DAIIN
7
5V-3V LEVEL SHIFT
A2-9
IC1206
A10
XRES
XLT3
D0-7
IC1204
XRDY
HA10
IC1207
16
1
HD0-7
XRESET
CLKSEL
1 TC74LCX245FTS1 19
LT1
LT1
XWRL
XRD
97
D0-D7,A0-A7
XWAIT
0
67
4
SDACK 77
90 XCDENA
XCDENA
XCDIRQ 100 XCDIRQ
66 DACK0
5V-3V LEVEL SHIFT
IC1202
TC74VHC541FTS1
3V-5V LEVEL SHIFT
IC1203
TC74VHCT08AFTS1
IC1006
PD3411A
XHRD,XHWRL,XHWRH
XHCS6,XHDACK1
HA1
11
140
XVFLD,XAVIRQ0,XDREQ1
205
EXTAL
48X44
XAMUTE
XLT3
60 79 50
XRES
2
98
62
IC1008
TC7SHU04FU
4
1
3
15
XRES
D0-D15,A0-A21
CTS
63 DTR
109
RXD
110 TXD
XFMWE 54 XFMWE
SSI,SSO,SSCK,XRDY,LT1
73
197
95
IC1015
TC7WU04FU
7 4
IC1009
CY2292SI-1A0
X1001
13.824MHz
CLOCK GENERATOR
8
10 1
9
3
CN1601
IC1011
TC7WU04FU
IC1012
TC7WU04FU
2
IC1010
TC7SHU04FU
4 27MMC
5
6
ICK27M
DDC5
DDC5
DDC5S
7
8
SRVDD5
9
VDD5
10
8VA
11
VD9
12
13
SRVDD5
VDD5
8VA
VD9
5
4 ICK27M
DDC3
DDC3
OVCO
DSPCLK
IC1014
TC7SHU04FU
3
4
XEXTRDY
6,7 OVCO
5 DACCLK
2
DDC2
VD25
133
XCS2
CTS
DTR
RXD
TXD
XHBE1
XINT1,XINT2
74 XTAL
X1000
20.000MHz
C
SSO 16
2,9
XAVIRQ1,XAVIRQ2
XDREQ0
XLT3
IC1002
TC7SET08FUS1
SSO
A1
XRES
XSDREQ 76 2
1
XRD 12 13
XRD,XWRL,
XWRH,XCS6,
XDACK1
D0-D15,A0-A21
51 XCS3
XCS3
XIRQL11 1 XIRQL11
XIRQL10 112 XIRQL10
19
SSCK
17
SSI
15
IC1208
TC74VHC00FTS1
56
STP2DREQ
6
XCS6
XDACK1
XWRL
XRD
3
B1
B2
4 C2 Q1600 E2 2
6
1
C1
E1
5
SSCK
SSI
8
75
XSWR
74
XSRD
IC1205
HD8-15
1 TC74LCX245FTS1 19
2
13
20
VDCONT
21
XSRSENS
22
(XMAG)MAGSW
24
VMCONT
27
(XMBSEN)XBSEN
7
XMRES
8
HA2-10,HD0-15
8 TC74VHC541FTS1 12
XRES
IC1705
TC7SHU04FU
9
XRES
MPEG DECODER
HA2-9
TC74VHC541FTS1
73
4
L
XAMUTE
IC1201
MB86373BPFV-G-BI
D8-15
D
SSI,SSO,SSCK,XRDY,LT1
XCS2
K
3
16
4
55 XCDENA
44 DECDRQ
43 XCDIRQ
22
A18
ASIC
D0-7
IC1701
HD74HC245T
1
cs 32
rd 30
wr 31
IC1702
LC89513KP
IC701
PD4995A
XSACK
SREQ
MCDIF
BUS BUFFER
DECD0-DECD7
BCK
LRCK
SDATA
C2PO
XTALCK
LPF
18
CN3951
XSACK
SREQ
MCDIF
DAC
IC1500
PE8001A1
5
F
XSACK 55
SREQ 56
DIFOUT 108
26
28
27
25
23
B
COMPOUT
1
28 21 22
IO0-7,RA0-13,
XROE,XRWE
CDBCK
CDLRCK
CDDATA
IPF
DSPCLK
F1500
CTF1515
MSM56V16160DP-10TS
SDRAM
XCS3
XCSLI 72
XIRQ11 103 XIRQL11
XIRQ10 102 XIRQL10
2
12
REF4V
Q1503
3
BCKA
LRCKA
DATA0
IC1200
IC1700
LC35256FT-70U
DAC5V
SSO,SSCK
1 A6
2
XCS3
1
Q1500
ANACOMP 45
SD0-SD7
IC705
TC7SH32FUS1
IC1504
HA178L05UA
CN3961
CDBCK 56
CDLRCK 55
CDDATA 54
CDBCK
BCK 109
LRCK 110 CDLRCK
ADATAO 111 CDDATA
3
F
8VA
SA6 85 4
DIGOUT
AODAI 64
DSPCLK
XRD
XWRL
XCS23
E
F
XDV-M8357ZT/UC
5
6
7
8
13
1
2
3
4
A
F
EXTENSION UNIT
VIDEO CIRCUIT
1
26
29
DIGO
10
CN3302
24
Q3151
4VREF
1 1
IC3101
NJM2068MD
7 4
IC3821
BA00AST
2
BVD
1
VDCONT
4
13
CN3801
4
2
3
5
COMPOUT
COMPO+
COMPIN
COMPI+
LP
L+
LM
L-
MUTE
VD9
TX+
TXACC
VMCONT
7
XBMUTE
ANSW
XMRES
17
XRES
16
VADCONT
XVMUTE
XRES
XSRSENS
67
XMAG
VIOC
XMRES
5
XSRSENS
SYSMUTE
3
IC3871
PQ20VZ11
IEPW
Q3851
DDC3
11
DDC3
10
1
56
1
57
2
IC3631
HA12187FP
Q3853
24
8
SWREG
IC3851
BA9706K
XBSEN
XASEN
XRST
6
64
5
62
11
60
7
Q3601
75
6
7
3
IC3891
PQ20VZ11
4
1
2
Q3811
OUT2
OUT1
12
3
IN1
RSTOUT
FBIN
IC3811
PAJ002A
VDD5
9
IN3
8V REGULATOR
XADEN
AVREF1
EF3831
BVD
2
IC3831
BA08SFP
4V REGULATOR
4
AV8CONT
52
4VREF
40
FANPW1
Q3891
53
AV8
Q3880
1
BVD
Q3812
4
AVREF0
FAN POWER SUPPLY
FAN+1
BVDD
10
2
IN2
CONT
OUT3
XRST
RSTIN
AV8
VD9
CN3891
1
OCD
63
BSR
VDD5
VD9
5
VDD5V,ASENSE,BSENSE,RESET
XMBSEN
11
SRVDD5
VDD5
8VA
VD9
6
8
55
IC3601
PE5272A
BSR
Q3852
DDC5
26
SYSTEM CONTROLLER
DC-DC
CONVERTER
5V REGULATOR
1
Q3301
35
1
9
DDC5
20
Q3814 Q3813
3.3V REGULATOR
1
13
IP-BUS DRIVER
2.6V REGULATOR
DDC2
13
DDC2
12
FAN
MOTOR
14
27
XMAG
IEDI
CN3951
7
6
5
4
3
12
AV8
IEDO
9
8
10
Q3131
28
11-13,
15,47
SSI,SSO,SCK,XRDY,LT1
9
11
XMBSEN
10
11
9
SYS MUTE
5
16
23
1
3
Q3201
Q3154
CN1601
IC3131
TC74HC4066AF
9V REGULATOR
Q3153
XAMUTE
12
E
5
IC3311
NJM2267V
Q3821
4
C
1
AUDIO CIRCUIT
2
REF4V
7
4
8
DIGO
Q3155
18
2
L
E
B
CN1600
22
19
CN3301
COMP
3
EXTERNAL CONNECTOR
COAXIAL CABLE
CN3961
IC3301
NJM2235V
X1
FANPW2
X2
70
69
H
CN3803
X3601
6.290MHZ
+B
D
2
EXTERNAL CONNECTOR
CN3802
+B
+B
+B
BSR
BSR
BVD
EF3802
BVD
MF UNIT
CN2901
9
8
6
7
2
3
5
4
1
10
+B
+B
+B
BSR
G
BVD
KEYBOARD PCB
ILLMI
BVDD
EF3801
BVDD
2
9
5
6
4
7
3
8
BVDD
CN2903
Q3931
XILL
XCLOSE
XEJ
ILLB
9
65
XCLOSE
66
XEJ
ILLB
XCLOSE
XEJ
ILLB
XCLOSE
XEJ
CN2000
1
1
2
2
3
3
ILLB
XCLOSE
XEJECT
S2001
EJECT
SW
E
F
14
XDV-M8357ZT/UC
1
2
3
4
S2000
CLOSE
SW
5
6
7
8
A
B
C
D
E
F
XDV-M8357ZT/UC
5
6
7
8
15
1
2
3
4
3.2 DVD/CD MECHANISM UNIT, MAIN PCB(SERVO SECTION)(GUIDE PAGE)
Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".
E-a 1/2
A
A-a
A-b
Large size
SCH diagram
R
T
A-a
A-b
%
$
#
Guide page
R(DVD)
R
A-a
A-b
R
Detailed page
R(DVD)
R(DVD)
PU UNIT
T
T
T
T
T
R
R(DVD)
B
R
3
T
R
R
T
R(CD)
R
2
T
R
RF AMP
T
!
R(CD)
56
7
C
T
T
SERVO DSP
1
T
C
S(CD)
8
A PCB UNIT(A)
0
C
C
DSP
S851
CSN1051
S852 TRP
CSN1052
C
TRP
VLED
T
C
D851
CN504-2
D
C
DSP
TRY+
T
C
Q851
PT4800
T
TRYM2
CXC1541
TRAY
CRGCRG+
M1
CXC1552
CARRIAGE
D
GND
DISC
PCB(B)
C PCB(A)
M4 CXC1540
E
C301
R1
EREF
4
EVREF
EPVO
C302
MAG
MAGSW
R01
GND0
S301
CSN1044
S(CD)
S(CD)
R301
5R6K
CN301
VR301
CCW1021
10K
1K(B)
S(DVD)
S(DVD)
MECHANISM
CONTROLLER
S(CD)
S(DVD)
B PCB UNIT(B)
M3
CXM1282
S(DVD)
VR302
CCP1338 R302
6R2K
^
SPDL
F
A B C D E 1/2
16
XDV-M8357ZT/UC
1
2
3
4
@
5
6
7
8
A
E-b 1/2
E 1/2
RF EQUALIZER
F
T
R
VCO
C
MAIN PCB(SERVO SECTION)
F.ACT DRIVE
S
T.ACT DRIVE
RF
CRG DRIVE
AUDIO
ROM
SPDL DRIVE
AUDIO(ANALOG) SIGNAL
ROM DATA SIGNAL
9
R(DVD)
&
B
LCD DRIVE
AUDIO
ROM
E 2/2
ROM
C
ROM
SERVO DSP
0
F JUMP
AUDIO
ROM
D
DRAM
ASIC
E
R(DVD)
S(DVD)
@
S(DVD)
NISM
LLER
Main Unit
Consists of
Main PCB
Keyboard PCB
NOTE :
Symbol indicates a resistor.
No differentiation is made between chip resistors and
discrete resistors.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
discrete capacitors.
Decimal points for resistor
and capacitor fixed values
are expressed as :
2.2 ← 2R2
0.022 ← R022
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
F
: The power supply is shown with the marked box.
E 1/2
XDV-M8357ZT/UC
5
6
7
8
17
1
2
T
3
1
!
T
C
T
0
SERVO DSP
1
S(CD)
7
T
T
56
R(CD)
A
F
E-a 1/2
XDV-M8357ZT/UC
4
C
D
T
3
C
8
R(DVD)
RF AMP
R(CD)
T
RF EQ
2
PU UNIT
A PCB UNIT(A)
R
R
R
R
R(DVD)
B
2
3
T
R(DVD)
R(DVD)
E-b 1/2
T
T
R
R
R
T
ROM
18
R
%
$
#
A-a E-b
E-a
1
4
T
C
E
T
5
M1
CXC1552
CARRIAGE
DISC
GND
CRG+
CRG-
TRY-
TRY+
6
R301
5R6K
1K(B)
B
C301
R1
VR302
CCP1338 R302
6R2K
MAGSW
GND0
S301
CSN1044
C302
MAG
R01
EPVO
EVREF
EREF
CN301
S(DVD)
4
SPDL
S(DVD)
S(CD)
S(CD)
T
T
T
A-a E-b
E-a
C
^
MECHANISM
CONTROLLER
@
0
6
M3
CXM1282
PCB UNIT(B)
10K
VR301
CCW1021
M4 CXC1540
C
C
D PCB(B) C PCB(A)
M2
CXC1541
TRAY
Q851
PT4800
DSP
TRP
VLED
C
C
8
C
D851
CN504-2
S851 DSP
CSN1051
S852 TRP
CSN1052
A PCB UNIT(A)
5
7
7
8
A
2
3
E-b 1/2
B
C
D
E
F
A B C D E-a 1/2
XDV-M8357ZT/UC
8
19
S(DVD)
S(DVD)
S(CD)
20
1
F JUMP
R(DVD)
9
D
LCD DRIVE
&
VCO
E-a E-b
F
C
T
R
T.ACT DRIVE
RF
CRG DRIVE
ROM
AUDIO
S
E-b 1/2
2
ROM
AUDIO
E 2/2
ROM DATA SIGNAL
AUDIO(ANALOG) SIGNAL
SPDL DRIVE
MAIN PCB(SERVO SECTION)
F.ACT DRIVE
E 1/2
2
1
XDV-M8357ZT/UC
O DSP
RF EQUALIZER
F
ROM
B
ROM
1
3
3
4
A
C
E
4
F JUMP
ROM
AUDIO
5
ROM
2
6
7
Decimal points for resistor
and capacitor fixed values
are expressed as :
2.2 ← 2R2
0.022 ← R022
7
: The power supply is shown with the marked box.
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
NOTE :
Symbol indicates a resistor.
No differentiation is made between chip resistors and
discrete resistors.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
discrete capacitors.
6
E-a E-b
Main Unit
Consists of
Main PCB
Keyboard PCB
ASIC
DRAM
5
8
A
3
XDV-M8357ZT/UC
8
B
C
D
E
F
E-b 1/2
21
R(DVD)
S(DVD)
S(DVD)
1
2
4
Note:1. The encircled numbers denote measuring pointes in the circuit diagram.
2. Reference voltage
VR21:2.1V
- Waveforms
A
2 CH2:TT
T-
3
1V/div.
2V/div.
2ms/div.
1 CH1:TEI
2 CH2:T-
DVD:32 tracks jump
1V/div.
2V/div.
2ms/div.
ch1 VR21 →
ch2 VR21 →
ch2 VR21 →
1V/div.
2V/div.
2ms/div.
DVD:1 track jump
CD:32 tracks jump
ch1 VR21 →
1 CH1:TEI
2 CH2:T-
ch1 VR21 →
ch2 VR21 →
B
1 CH1:TEI
2 CH2:T-
1V/div.
2V/div.
2ms/div.
3 CH1:F2V/div.
3 CH1:F2V/div.
500ms/div.
500ms/div.
4 CH2:EC(TP308) 1V/div.
4 CH2:EC(TP308) 1V/div.
CD:S curve check
Servo adjustment mode
DVD:S curve check
Servo adjustment mode
CD:1 track jump
ch1 VR21 →
ch1 VR21 →
ch1 VR21 →
ch2 VR21 →
ch2 VR21 →
C
ch2 VR21 →
5 CH1:FEI
500mV/div. 2ms/div.
5 CH1:FEI
DVD:S curve check
Servo adjustment mode
500mV/div. 2ms/div.
2 layer DVD:S curve check
Servo adjustment mode
5 CH1:FEI
500mV/div. 2ms/div.
CD:S curve check
Servo adjustment mode
D
ch1 VR21 →
6
1 CH2:TEI
E
ch1 VR21 →
ch1 VR21 →
3 CH1:F500mV/div.
6 CH1:RFRP(TP405) 500mV/div.
2ms/div.
5ms/div.
4 CH2:EC(TP308)
1V/div.
1 CH2:TEI
1V/div.
CD:RFRP waveform
Focus close situation
ch1 VR21 →
ch2 VR21 →
ch2 VR21 →
500ms/div.
DVD:Focus close situation
CD:RFRP waveform
Focus close situation
ch1 VR21 →
1V/div.
1V/div.
ch1 VR21 →
ch2 VR21 →
F
22
XDV-M8357ZT/UC
1
2
3
4
5
3 CH1:F4 CH2:EC(TP308)
6
1V/div.
1V/div.
500ms/div.
CD:focus close
7
A
5 CH1:FEI
500mV/div.
v
v.
5 CH1:FEI
500mV/div.
v
v.
10ms/div.
7 CH2:SBAD(TP407) 500mV/div.
v
v.
7 CH2:SBAD(TP407) 500mV/div.
v
v.
v.
CD:focus close
DVD:focus close
ch1 VR21 →
8
ch1 VR21 →
ch1 VR21 →
ch2 VR21 →
ch2 VR21 →
ch2 VR21 →
B
8 CH1:C-(TP313)
4 CH2:EC(TP308)
2V/div.
1V/div.
500m/div.
DVD:CRG inside→outside
8 CH1:C-(TP313)
4 CH2:EC(TP308)
2V/div.
1V/div.
500m/div.
9 CH1:Ain(TP210) 1V/div.
0 CH2:FLGB(TP413) 5V/div.
500µs/div.
DVD:passing black dot (1mm)
CD:CRG inside→outside
ch1 VR21 →
ch1 VR21 →
ch1 VR21 →
ch2 VR21 →
ch2 VR21 →
C
ch2 VR21 →
! CH1:RFOI
1V/div.
0 CH2:FLGB(TP413) 5V/div.
500µs/div.
CD:passing black dot (1mm)
3 CH1:F2 CH2:T-
2V/div.
2V/div.
200µs/div.
DVD:passing black dot (1mm)
3 CH1:F2 CH2:T-
2V/div.
2V/div.
500µs/div.
CD:passing black dot (1mm)
D
ch1 VR21 →
ch1 VR21 →
ch1 VR21 →
ch2 VR21 →
ch2 VR21 →
ch2 VR21 →
9 CH1:Ain(TP210) 500mV/div.100ns/div.
0 CH1:RFOI
DVD:during playback Ain waveform
CD:during playback RFOI waveform
1V/div.
500ns/div.
5 CH1:FEI
3 CH2:F-
200mV/div.
1ms/div.
1V/div.
DVD:during playback FEI waveform
E
ch1 VR21 →
ch1 VR21 →
ch1 GND →
ch2 VR21 →
F
XDV-M8357ZT/UC
5
6
7
8
23
1
A
5 CH1:FEI
3 CH2:F-
2
200mV/div.
1ms/div.
1V/div.
CD:during playback FEI waveform
3
1 CH1:TEI
2 CH2:T-
200mV/div.
1V/div.
1ms/div.
4
1 CH1:TEI
2 CH2:T-
200mV/div.
1V/div.
1ms/div.
DVD:during playback TEI waveform
CD:during playback TEI waveform
ch1 VR21 →
ch1 VR21 →
ch1 VR21 →
ch2 VR21 →
ch2 VR21 →
ch2 VR21 →
B
5 CH1:FEI
1 CH2:TEI
500mV/div.
500ms/div.
1V/div.
5 CH1:FEI
1 CH2:TEI
500mV/div.
1V/div.
1s/div.
2 layer DVD:setup
DVD:setup
ch1 GND →
5 CH1:FEI
1 CH2:TEI
500mV/div.
500ms/div.
1V/div.
CD:setup
ch1 GND →
ch1 GND →
ch2 GND →
ch2 GND →
C
ch2 GND →
5 CH1:FEI
500mV/div.
v
v.
5 CH1:FEI
500mV/div.
v
v.
5 CH1:FEI
500mV/div.
v
v.
500ms/div.
500ms/div.
500ms/div. @ CH2:FEB(TP522) 200mV/div.
v
v.
@ CH2:FEB(TP522) 500mV/div.
v
v.
@ CH2:FEB(TP522) 200mV/div.
v
v.
DVD:focus balance adjustment
2 layer DVD:focus balance adjustment
CD:focus balance adjustment
D
ch1 VR21 →
ch1 VR21 →
ch1 VR21 →
ch2 VR21 →
ch2 VR21 →
ch2 VR21 →
# CH1:TP101
5V/div.
$ CH2:TP102
5V/div.
% CH3:TP103
5V/div.
DVD:LCD tilt servo
E
1ms/div.
# CH1:TP101
200mV/div.
v
v.
& CH1:VCO 500mV/div. 200ns/div.
1s/div.
^ CH4:LCDTILT(TP504)
L
LT(TP504)
100mV/div.
v
v.
DVD:LCD tilt servo
DVD:VCO
CH1, CH4:offset voltage 2.5V
ch1 GND →
ch4 GND →
ch1 GND →
ch1 GND →
ch2 GND →
ch3 GND →
F
24
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
A
* IC1201 pin 45 200mV/div.
10µs/div.
Composite signal output
ch1 GND →
B
C
D
E
F
XDV-M8357ZT/UC
5
6
7
8
25
1
2
3
4
3.3 MAIN PCB(DECODER SECTION)(GUIDE PAGE)
A
E-a 2/2
B
E 1/2
ROM
MPEG DECODER
C
AU
*
VIDEO
D
E
(PROGRAM)
F
E 2/2
26
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
A
E-b 2/2
E 2/2
MAIN PCB(DECODER SECTION)
AU
AU
AU
B
AU
F
CN3961
AU
AU
VIDEO
ROM
VIDEO
VIDEO
C
AU
*
AU
VIDEO
D
F
CN3951
E
Main Unit
Consists of
Main PCB
Keyboard PCB
ROM
VIDEO
ROM DATA SIGNAL
VIDEO SIGNAL(COMPOSITE)
AU
AUDIO SIGNAL
AU(D)
AUDIO SIGNAL(DIGITAL)
F
E 2/2
XDV-M8357ZT/UC
5
6
7
8
27
2
1
2
3
4
*
1
A
MPEG DECODER
E-b 2/2
B
A-a E-b
E-a
C
D
E 1/2
AU
ROM
E
F
E-a 2/2
28
XDV-M8357ZT/UC
3
4
5
6
7
8
*
VIDEO
A
1
E-b 2/2
2
B
A-a E-b
E-a
C
(PROGRAM)
D
E
F
E-a 2/2
XDV-M8357ZT/UC
5
6
7
8
29
30
*
AU
ROM
1
AU
AU
2
AU
VIDEO
F
CN3961
2
VIDEO
AU
C
MAIN PCB(DECODER SECTION)
B
VIDEO
AU
E 2/2
E-a E-b
1
3
3
4
A
AU
D
E
F
E-b 2/2
XDV-M8357ZT/UC
4
*
AU
AU
5
6
ROM
1
7
AUDIO SIGNAL(DIGITAL)
AUDIO SIGNAL
VIDEO SIGNAL(COMPOSITE)
7
E-a E-b
AU(D)
AU
ROM DATA SIGNAL
6
VIDEO
Main Unit
Consists of
Main PCB
Keyboard PCB
F
CN3951
5
8
A
B
C
D
E
VIDEO
F
2
E-b 2/2
XDV-M8357ZT/UC
8
31
1
2
3
4
3.4 EXTENSION UNIT
A
F-a
CABLE
B
E 2/2
CN1600
C
SYSTEM CONTROL
D
>
1.5A
> 1.5A
E 2/2
CN1601
E
DDC2(2.6V)
DDC5(5V), DDC3(3.3V)
POWER SUPPLY FOR
AUDIO AND VIDEO
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
F
F
32
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
A
F-b
F
EXTENSION UNIT
EXTERNAL
CONNECTOR
CABLE
B
C
D
B.SENSE, A.SENSE
RESET VDD(5V)
H
EXTERNAL
CONNECTOR
CN2901
E
POWER SUPPLY FOR MECHANISM
FOR
O
POWER SUPPLY FOR FAN
FAN
CXM1195
F
F
XDV-M8357ZT/UC
5
6
7
8
33
F
34
SYSTEM CONTROL
F-b
CABLE
A
1
2
2
3
CN1600
E 2/2
A-a
F-a F-b
1
3
4
B
C
D
E
F-a
XDV-M8357ZT/UC
4
5
6
CN1601
E 2/2
1.5A
A-a
F-a F-b
DDC5(5V), DDC3(3.3V)
POWER SUPPLY FOR
AUDIO AND VIDEO
6
7
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.
DDC2(2.6V)
> 1.5A
>
5
7
8
A
1
F-b
B
C
D
E
F
F-a
XDV-M8357ZT/UC
8
35
1
2
3
4
3
4
EXTERNAL
CONNECTOR
EXTENSION UNIT
A
F
B
F-a F-b
C
D
E
CABLE
F
F-b
36
XDV-M8357ZT/UC
1
2
5
6
FAN
CXM1195
POWER SUPPLY FOR FAN
B.SENSE, A.SENSE
RESET VDD(5V)
F-a F-b
POWER SUPPLY FOR MECHANISM
H
CN2901
EXTERNAL
CONNECTOR
5
6
7
7
8
A
B
C
D
E
F
1
F-b
XDV-M8357ZT/UC
8
37
1
2
3
4
3.5 KEYBOARD PCB
A
H
G
CN2903
KEYBOARD PCB
B
C
EJECT
CLOSE
D
E
Main Unit
Consists of
Main PCB
Keyboard PCB
F
G
38
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
3.6 MF UNIT
A
H
MF UNIT
B
G
CN2000
Maintenance of BSR
Filter of +B
F
ERA15-02VH
CN3802
2200/16
2200/16
3300/16
3300/16
3300/16
C
Maintenance of VDD
2 1
CN2902
Earth Plate
D
E
F
H
XDV-M8357ZT/UC
5
6
7
8
39
1
2
3
4
4. PCB CONNECTION DIAGRAM
4.1 MAIN PCB
A
NOTE FOR PCB DIAGRAMS
10
SIDE A
B
SIDE B
20
Chip Part
P.C.Board
30
40
C
50
60
D
70
80
E
90
100
110
F
E
40
XDV-M8357ZT/UC
1
2
3
4
50
40
30
20
0
Capacitor
Connector
10
MAIN PCB
Y
E
X
1.The parts mounted on this PCB
include all necessary parts for
several destination.
For further information for
respective destinations, be sure
to check with the schematic diagram.
2.Viewpoint of PCB diagrams
5
6
7
8
A
130
120
110
90
80
70
60
50
100
SIDE A
B
C
D
E
F
E
XDV-M8357ZT/UC
5
6
7
8
41
70
80
90
4
100
MAIN PCB
3
110
E
130
A
2
120
1
M3 SPDL MOTOR
F
CN3951
F
CN3961
B
C
D
E
TC1000
DSPCLK
F
E
42
XDV-M8357ZT/UC
1
2
3
4
P
5
6
7
8
A
M4 ELV MOTOR
C
10
PU UNIT
B
CN301
40
30
20
B
50
C
60
TP210
D
80
70
VCO
100
90
E
110
OTOR
X
0
Y
10
20
30
40
50
60
70
SIDE B
F
E
XDV-M8357ZT/UC
5
6
7
8
43
1
2
3
4
4.2 EXTENSION UNIT
A
B
F
EXTENSION UNIT
H
CN2901
60
C
E
50
E
CN1600
CN1
40
30
D
20
10
CORD ASSY
Y
0
X
E
10
20
30
40
50
60
70
80
90
100
F
F
44
XDV-M8357ZT/UC
1
2
3
4
110
120
5
6
7
8
A
B
SIDE A
C
E
CN1601
D
110
120
130
140
150
160
170
180
190
200
210
220
230
E
F
F
XDV-M8357ZT/UC
5
6
7
8
45
1
2
3
4
A
B
F
EXTENSION UNIT
C
D
220
230
210
200
190
180
160
170
150
140
130
E
F
F
46
XDV-M8357ZT/UC
1
2
3
4
120
110
5
6
7
8
A
B
SIDE B
60
C
50
40
30
D
20
10
Y
120
110
100
90
80
60
70
50
40
30
20
10
0
X
E
F
F
XDV-M8357ZT/UC
5
6
7
8
47
1
2
3
4
4.3 KEYBOARD PCB
A
B
G KEYBOARD PCB
SIDE A
G KEYBOARD PCB
SIDE B
CLOSE
C
40
40
30
30
EJECT
20
20
10
10
D
Y
Y
0
E
X
10
30
20
H
30
20
0
10
X
CN2903
F
G
48
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
4.4 MF UNIT
MF UNIT
G
SIDE A
H
MF UNIT
SIDE B
A
CN2000
B
C
D
F
E
CN3802
H
F
H
XDV-M8357ZT/UC
5
6
7
8
49
1
2
3
4
4.5 DVD/CD MECHANISM UNIT
A
A
PCB UNIT(A)
SIDE A
A
PCB UNIT(A)
SIDE B
TRP
D851
B
DSP
1
4
C
C
D
E
F
A
50
XDV-M8357ZT/UC
1
2
3
4
5
B
6
7
8
PCB UNIT(B)
SIDE A
A
MAG
B
C
B
PCB UNIT(B)
E
CN310
SIDE B
D
EPVO
EREF
E
F
B
XDV-M8357ZT/UC
5
6
7
8
51
1
C
A
2
3
4
E
PCB(A)
CN302
1
9
B
C
A
1
4
Q851
D
E
M1
CARRIAGE
M
1 2
F
D
C
52
XDV-M8357ZT/UC
1
2
3
4
5
D
6
7
8
PCB(B)
A
M
B
M2
TRAY
C
C
2
1
D
E
F
D
XDV-M8357ZT/UC
5
6
7
8
53
1
2
3
4
5. ELECTRICAL PARTS LIST
A
B
NOTE:
• Parts whose parts numbers are omitted are subject to being not supplied.
• The part numbers shown below indicate chip components.
Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
• The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
• Meaning of the figures and others in the parentheses in the parts list.
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding
PC board.
IC 301 (A, 91, 111) IC NJM2068V
Circuit Symbol and No.
C
D
E
Unit Number:CWX3187
Unit Name:Main Unit
Unit Number:CWX3198
Unit Name:Extension Unit
Unit Number:CWM6518
Unit Name:MF Unit
Unit Number:
Unit Name:PCB Unit(A)
Unit Number:
Unit Name:PCB Unit(B)
Unit Number:
Unit Name:PCB(A)
Unit Number:
Unit Name:PCB(B)
Main Unit
Consists of
Main PCB
Keyboard PCB
EG
Unit Number:CWX3187
Unit Name:Main Unit
MISCELLANEOUS
F
IC 101
IC 102
IC 103
IC 105
IC 106
(A,19,35)
(B,29,71)
(B,31,56)
(B,46,47)
(A,47,52)
IC
IC
IC
IC
IC
IR3C07N
NJM2904M
TA1254AF
NJM3404AM
TC7WU04FU
IC 107
IC 108
(A,44,65) IC
(B,52,50) IC
PA0065AM
NJM3404AM
54
Circuit Symbol and No.
Part No.
Part No.
IC 109
IC 203
IC 204
(A,39,55) IC
(A,43,40) IC
(B,63,11) IC
TC7WU04FU
NJM2100M
NJM2100M
IC 206
IC 301
IC 303
IC 304
IC 305
(B,62,28) IC
(B,16,103) IC
(B,22,96) IC
(B,43,91) IC
(B,25,18) IC
TC74VHCU04FT
TC4W53F
NJM2904M
BA6797FM
LB1836M
IC 351
IC 352
IC 353
IC 401
IC 402
(B,12,82)
(B,14,92)
(B,58,40)
(B,34,34)
(A,41,82)
IC
IC
IC
IC
IC
TC4S66F
MC33202D
MC33202D
TC9461F
NJM2904M
IC 501
IC 601
IC 604
IC 605
IC 701
(A,40,17)
(B,26,88)
(B,26,81)
(B,26,77)
(A,74,22)
IC
IC
IC
IC
IC
PEG114A
TC4053BFT
NJM3414AV
NJM3414AV
PD4995A
IC 702
IC 703
IC 704
IC 705
IC 706
(B,80,16)
(A,17,27)
(A,21,21)
(B,77,27)
(A,23,27)
IC
IC
IC
1 chip OR gate
IC
MSM5117800F-60JS
LC89170MP
TC7SET08FUS1
TC7SH32FUS1
TC7SET08FUS1
IC 707
IC 1000
IC 1001
IC 1002
IC 1003
(A,19,21)
(B,76,50)
(B,95,51)
(B,82,30)
(B,70,44)
IC
IC
IC
IC
IC
TC7SET04FUS1
M5M51008DKV-70HI
PD6531A
TC7SET08FUS1
TC7SHU04FU
IC 1004
IC 1005
IC 1006
IC 1007
IC 1008
(B,85,73)
(B,79,34)
(B,64,72)
(A,57,63)
(A,66,99)
IC
IC
IC
IC
IC
PD6520A
MAX662AESA
PD3411A
TC74VHC139FT
TC7SHU04FU
IC 1009
IC 1010
IC 1011
IC 1012
IC 1013
(B,87,92)
(B,95,89)
(B,75,98)
(B,99,97)
(B,63,91)
IC
IC
IC
IC
IC
CY2292SI-1A0
TC7SHU04FU
TC7WU04FU
TC7WU04FU
TC7SH08FUS1
IC 1014
IC 1015
IC 1200
(B,98,89) IC
(B,84,100) IC
(B,99,73) IC
TC7SHU04FU
TC7WU04FU
MSM56V16160DP-10TS
XDV-M8357ZT/UC
1
2
3
4
5
6
Circuit Symbol and No.
7
Part No.
8
Circuit Symbol and No.
Part No.
IC 1201
IC 1202
(A,85,80) IC
(A,90,54) IC
MB86373BPFV-G-BI
TC74VHC541FTS1
L 1004
L 1005
(B,80,87) Inductor
(B,62,55) Inductor
CTF1473
CTF1473
IC 1203
IC 1204
IC 1205
IC 1206
IC 1207
(A,83,54)
(A,77,54)
(A,69,52)
(A,62,70)
(A,62,78)
TC74VHCT08AFTS1
TC74LCX245FTS1
TC74LCX245FTS1
TC74VHC541FTS1
TC74VHC541FTS1
L
L
L
L
L
1007
1008
1009
1010
1011
(B,54,86) Inductor
(B,78,96) Inductor
(A,56,59) Inductor
(A,64,99) Inductor
(A,69,100) Inductor
CTF1473
CTF1473
CTF1473
CTF1473
CTF1470
IC 1208
IC 1500
IC 1501
IC 1502
IC 1503
(A,97,45) IC
(B,66,105) IC
(A,52,87) IC
(B,59,96) IC
(A,52,111) IC
TC74VHC00FTS1
PE8001A1
MC33202D
MC33202D
NJM2068MD
L
L
L
L
L
1012
1013
1014
1015
1016
(B,92,87) Inductor
(B,77,103) Inductor
(B,98,99) Inductor
(B,61,92) Inductor
(B,79,39) Inductor
CTF1473
CTF1473
CTF1473
CTF1473
CTF1473
IC 1504
IC 1700
IC 1701
IC 1702
IC 1704
(B,54,108) IC
(A,106,21) IC
(A,100,31) IC
(B,99,28) IC
(A,106,29) IC
HA178L05UA
LC35256FT-70U
HD74HC245T
LC89513KP
TC7S02FU
L
L
L
L
L
1017
1018
1200
1201
1202
(B,98,85) Inductor
(B,80,100) Inductor
(B,103,60) Inductor
(A,104,89) Inductor
(A,94,55) Inductor
CTF1473
CTF1473
CTF1453
CTF1473
CTF1473
IC 1705
IC 1706
IC 1707
Q 101
Q 102
(A,97,37) IC
(A,66,62) IC
(A,102,37) IC
(A,13,47) Transistor
(A,17,47) Transistor
TC7SHU04FU
TC74VHC238FT
TC7SHU04FU
2SD601A
2SB709A
L
L
L
L
L
1203
1204
1205
1206
1207
(A,82,50) Inductor
(A,97,110) Inductor
(A,75,60) Inductor
(A,97,101) Inductor
(A,92,42) Inductor
CTF1473
CTF1473
CTF1473
CTF1453
CTF1473
Q
Q
Q
Q
Q
103
104
165
168
203
(B,43,63)
(A,24,65)
(A,39,45)
(A,22,51)
(A,50,43)
Transistor
Transistor
Transistor
Transistor
Transistor
DTC114EU
2SB1260
2SB709A
FMC5A
2SB709A
L
L
L
L
L
1208
1209
1210
1500
1503
(A,66,57) Inductor
(A,57,75) Inductor
(A,63,82) Inductor
(A,79,107) Inductor
(B,51,107) Inductor
CTF1473
CTF1473
CTF1473
CTF1473
CTF1473
Q
Q
Q
Q
Q
204
401
402
403
404
(A,53,33)
(A,34,79)
(A,34,84)
(A,44,76)
(A,38,76)
Transistor
Transistor
Transistor
Transistor
Transistor
2SD601A
2SB709A
2SD1781K
IMX1
2SB1132
L
L
L
L
L
1600
1601
1602
1603
1604
(B,35,125)
(B,31,125)
(B,28,125)
(B,23,125)
(B,10,115)
Inductor
Inductor
Inductor
Inductor
Inductor
CTF1453
CTF1453
CTF1453
CTF1453
CTF1453
Q
Q
Q
Q
Q
501
601
1500
1503
1600
(B,51,20) Transistor
(B,28,93) Transistor
(A,72,103) Transistor
(A,75,113) Transistor
(A,76,120) Transistor
DTA114EU
DTC114EU
2SA1037K
2SA1037K
UMH8N
L
L
L
L
L
1606
1607
1608
1609
1610
(B,26,124)
(A,70,122)
(B,10,112)
(A,77,125)
(A,78,125)
Inductor
Inductor
Inductor
Inductor
Inductor
CTF1473
CTF1470
CTF1453
CTF1470
CTF1470
D
D
D
D
L
201
305
2000
2001
101
(B,68,20) Diode
(A,26,7) Diode
(A,12,45) Diode
(A,21,28) LED
(A,13,35) Inductor
KV1410-F1
1SR154-400
UDZ18(B)
SML-210FT(JK)
CTF1473
L
L
L
L
L
1611
1612
1613
1615
1616
(A,80,125)
(A,89,125)
(A,90,125)
(A,85,120)
(A,84,125)
Inductor
Inductor
Inductor
Inductor
Inductor
CTF1470
CTF1470
CTF1470
CTF1470
CTF1470
L
L
L
L
L
120
121
122
123
201
(A,44,53)
(B,47,59)
(A,37,71)
(B,44,53)
(A,53,37)
Inductor
Inductor
Inductor
Inductor
Inductor
CTF1473
CTF1473
CTF1473
CTF1473
LCTC4R7K2125
L
L
L
L
L
1617
1618
1622
1624
1630
(A,85,125)
(A,87,125)
(A,70,121)
(A,75,125)
(B,20,125)
Inductor
Inductor
Inductor
Inductor
Inductor
CTF1470
CTF1470
CTF1470
CTF1470
CTF1453
L
L
L
L
L
202
203
400
500
701
(B,73,27)
(B,61,32)
(A,26,33)
(A,36,35)
(B,94,15)
Chip Coil
Inductor
Inductor
Inductor
Inductor
LCTAW1R5J2520
CTF1473
CTF1473
CTF1473
CTF1473
L
L
L
L
L
1631
1632
1633
1634
1635
(A,80,122)
(A,81,125)
(A,80,121)
(A,82,125)
(A,80,119)
Inductor
Inductor
Inductor
Inductor
Inductor
CTF1470
CTF1470
CTF1470
CTF1470
CTF1470
L
L
L
L
L
702
801
804
805
1000
(B,77,29)
(A,89,41)
(A,16,22)
(A,22,25)
(B,80,60)
Inductor
Inductor
Inductor
Ferrite Bead
Inductor
CTF1473
CTF1453
CTF1473
CTF1528
CTF1473
L
L
L
L
L
1701
1702
1704
1705
1706
(A,114,23)
(B,104,41)
(A,100,27)
(A,107,32)
(A,100,39)
Inductor
Inductor
Inductor
Inductor
Inductor
CTF1473
CTF1473
CTF1473
CTF1473
CTF1473
CTF1473
CTF1473
CTF1473
L 1707
L 1708
TC201
(A,61,59) Inductor
(A,104,37) Inductor
(B,70,31) Trimmer
CTF1473
CTF1473
CCG1039
L 1001
L 1002
L 1003
IC
IC
IC
IC
IC
(B,82,54) Inductor
(B,79,31) Inductor
(B,68,44) Inductor
A
B
C
D
E
F
XDV-M8357ZT/UC
5
6
7
8
55
1
Circuit Symbol and No.
A
2
Part No.
TC1000
X 501
(B,90,100) Trimmer Condenser CCL1053
(A,41,31) Radiator 10.00MHz CSS1428
X
X
S
S
F
(B,47,74) Radiator 20.00MHz
(A,89,106) Radiator 13.824MHz
(A,20,45) Switch(CLOSE)
(A,21,23) Switch(EJECT)
(A,75,108) Filter
1000
1001
2000
2001
1500
CSS1470
CSS1509
CSN1051
CSG1110
CTF1515
RESISTORS
B
C
D
E
F
R
R
R
R
R
101
102
103
104
106
(A,12,51)
(A,13,51)
(A,15,51)
(A,18,51)
(A,44,59)
RS1/16S0R0J
RS1/16S102J
RS1/16S122J
RS1/16S182J
RS1/16S0R0J
R
R
R
R
R
108
109
110
111
112
(B,26,48)
(A,23,61)
(A,23,58)
(A,23,55)
(A,22,48)
RS1/16S0R0J
RS1/10S1R5J
RS1/10S1R5J
RS1/10S1R5J
RS1/10S1R5J
R
R
R
R
R
113
114
115
116
118
(B,32,75)
(B,38,74)
(A,35,57)
(A,25,60)
(B,37,50)
RS1/16S103J
RS1/16S103J
RS1/16S222J
RS1/16S0R0J
RS1/16S0R0J
R
R
R
R
R
119
120
121
122
123
(A,35,56)
(B,39,51)
(B,52,42)
(A,13,33)
(A,15,41)
RS1/16S222J
RS1/16S0R0J
RS1/16S393J
RS1/10S3R9J
RS1/16S104J
R
R
R
R
R
124
125
126
127
133
(A,24,46)
(A,35,55)
(B,45,65)
(A,43,50)
(B,31,47)
RS1/10S1R5J
RS1/16S222J
RS1/16S122J
RS1/16S222J
RS1/16S0R0J
R
R
R
R
R
134
136
137
138
139
(B,37,65)
(B,41,62)
(B,43,65)
(B,41,64)
(A,27,49)
RA3C101J
RS1/16S331J
RS1/16S112J
RS1/16S302J
RS1/16S0R0J
R
R
R
R
R
140
141
143
144
145
(A,29,47)
(B,35,48)
(B,44,57)
(B,46,53)
(A,38,57)
RS1/16S103J
RS1/16S101J
RS1/16S103J
RS1/16S103J
RS1/16S223J
R
R
R
R
R
146
147
148
149
150
(A,40,52)
(A,43,55)
(A,45,51)
(A,49,53)
(A,51,53)
RS1/16S223J
RS1/16S223J
RS1/16S223J
RS1/16S103J
RS1/16S222J
R
R
R
R
R
154
155
156
157
158
(B,49,53)
(B,53,55)
(B,54,55)
(B,55,45)
(B,51,54)
RS1/16S123J
RS1/16S182J
RS1/16S123J
RS1/16S822J
RS1/16S182J
R
R
R
R
R
159
160
164
165
166
(B,52,43)
(A,33,50)
(A,27,50)
(A,38,47)
(A,41,48)
RS1/16S203J
RS1/16S101J
RS1/16S203J
RS1/16S101J
RS1/16S222J
56
3
4
Circuit Symbol and No.
Part No.
R
R
R
R
R
170
171
172
201
214
(A,23,71)
(A,26,71)
(A,27,62)
(A,50,50)
(A,46,44)
RS1/8S100J
RS1/8S120J
RS1/16S470J
RS1/16S0R0J
RS1/16S222J
R
R
R
R
R
215
216
217
220
221
(A,50,47)
(A,55,37)
(A,49,46)
(A,48,39)
(A,49,33)
RS1/16S152J
RS1/16S471J
RS1/16S102J
RS1/16S105J
RS1/16S161J
R
R
R
R
R
222
223
224
225
230
(A,48,37)
(A,51,31)
(A,52,40)
(A,55,40)
(B,63,24)
RS1/16S103J
RS1/16S220J
RS1/16S223J
RS1/16S153J
RS1/8S0R0J
R
R
R
R
R
231
232
233
234
235
(B,59,24)
(B,57,26)
(B,71,27)
(B,68,28)
(B,68,26)
RS1/16S104J
RS1/16S220J
RS1/16S101J
RS1/16S0R0J
RS1/16S104J
R
R
R
R
R
236
237
238
239
240
(B,68,23)
(B,66,21)
(B,63,16)
(B,65,18)
(B,67,10)
RS1/16S104J
RS1/16S202J
RS1/16S105J
RS1/16S222J
RS1/16S103J
R
R
R
R
R
241
242
243
244
245
(B,63,17)
(B,63,19)
(B,63,20)
(B,60,17)
(B,60,19)
RS1/16S683J
RS1/16S153J
RS1/16S153J
RS1/16S223J
RS1/16S153J
R
R
R
R
R
246
247
248
249
250
(B,60,20)
(B,64,6)
(B,60,10)
(B,60,13)
(A,55,34)
RS1/16S103J
RS1/16S102J
RS1/16S153J
RS1/16S153J
RS1/10S0R0J
R
R
R
R
R
251
301
302
303
304
(B,63,34)
(B,33,99)
(B,59,34)
(B,53,38)
(B,47,10)
RS1/10S0R0J
RS1/16S622J
RS1/16S473J
RS1/16S434J
RS1/16S104J
R
R
R
R
R
306
308
310
315
316
(B,14,107)
(A,14,19)
(A,11,20)
(B,50,85)
(B,49,87)
RS1/16S101J
RS1/10S201J
RS1/10S221J
RS1/16S103J
RS1/16S103J
R
R
R
R
R
317
318
322
323
324
(B,24,103)
(B,53,98)
(B,51,94)
(B,51,96)
(B,48,103)
RS1/16S822J
RS1/16S0R0J
RS1/16S1002D
RS1/16S1002D
RS1/16S0R0J
R
R
R
R
R
325
326
328
329
331
(B,46,102)
(B,52,98)
(B,20,102)
(B,22,103)
(B,21,103)
RS1/16S0R0J
RS1/16S1002D
RS1/16S822J
RS1/16S822J
RS1/16S822J
R
R
R
R
R
337
338
339
340
344
(B,37,101)
(B,36,99)
(B,34,82)
(B,37,81)
(B,33,86)
RS1/16S0R0J
RS1/16S0R0J
RS1/16S0R0J
RS1/16S0R0J
RS1/16S1002D
XDV-M8357ZT/UC
1
2
3
4
5
Circuit Symbol and No.
6
7
Part No.
Circuit Symbol and No.
8
Part No.
R
R
R
R
R
345
346
348
349
350
(B,34,88)
(B,34,84)
(B,33,97)
(B,32,95)
(B,34,94)
RS1/16S1002D
RS1/16S1002D
RS1/16S1202D
RS1/16S1202D
RS1/16S1202D
R
R
R
R
R
443
448
450
501
502
(A,37,89)
(A,35,42)
(A,36,42)
(B,56,16)
(B,49,19)
RS1/16S622J
RS1/16S221J
RS1/16S103J
RS1/16S3902D
RS1/16S1502D
R
R
R
R
R
352
354
355
356
358
(B,17,93)
(B,31,97)
(B,13,97)
(B,10,92)
(B,13,86)
RS1/16S103J
RS1/16S0R0J
RS1/16S103J
RS1/16S103J
RS1/16S103J
R
R
R
R
R
503
504
505
506
507
(B,44,17)
(B,41,17)
(B,51,18)
(B,43,17)
(B,46,15)
RS1/16SS473J
RS1/16S683J
RS1/16SS473J
RS1/16S103J
RS1/16S222J
R
R
R
R
R
359
360
361
362
364
(B,17,91)
(B,13,85)
(B,15,83)
(B,15,87)
(A,59,39)
RS1/16S103J
RS1/16S114J
RS1/16S153J
RS1/16S243J
RS1/16S624J
R
R
R
R
R
508
509
510
511
512
(B,41,18)
(B,50,16)
(B,54,18)
(B,33,13) 3.3kΩ
(A,48,30)
RS1/16S222J
RS1/16S222J
RS1/16S1002D
CCN1122
RS1/16S104J
R
R
R
R
R
365
366
368
369
370
(B,52,41)
(A,61,41)
(B,63,37)
(B,60,36)
(B,54,36)
RS1/16S624J
RS1/16S104J
RS1/16S333J
RS1/16S333J
RS1/16S101J
R
R
R
R
R
514
515
516
517
518
(B,46,17)
(A,45,28)
(B,38,20)
(A,37,29)
(A,36,33)
RS1/16S682J
RS1/16S102J
RS1/16S102J
RS1/16S222J
RS1/16S104J
R
R
R
R
R
372
373
374
401
402
(B,55,34)
(B,53,34)
(B,58,34)
(A,33,47)
(A,35,47)
RS1/16S103J
RS1/16S333J
RS1/16S103J
RS1/16S101J
RS1/16S101J
R
R
R
R
R
519
520
521
522
524
(A,35,30)
(A,35,33)
(B,37,20)
(B,42,14)
(B,32,17)
RS1/16S222J
RS1/16S104J
RS1/16S103J
RA3C104J
RS1/16S103J
R
R
R
R
R
404
405
406
407
408
(B,29,99)
(B,31,100)
(B,39,44)
(B,52,100)
(A,29,44)
RS1/16S1202D
RS1/16S3300D
RS1/16S332J
RS1/16S1002D
RS1/16S0R0J
R
R
R
R
R
526
527
528
529
530
(A,21,16)
(B,46,12) 22Ω
(B,45,22)
(B,46,18)
(B,28,13)
RS1/16SS473J
CCN1111
RA3C473J
RS1/16S682J
RS1/16S103J
R
R
R
R
R
409
410
411
412
413
(B,40,44)
(B,25,44)
(A,40,73)
(B,25,46)
(A,25,23)
RS1/16S153J
RS1/16S225J
RS1/16S272J
RS1/16S333J
RS1/16SS104J
R
R
R
R
R
531
532
534
535
536
(B,31,16)
(B,34,17)
(B,44,9)
(B,46,9)
(A,24,13)
RS1/16S103J
RS1/16S103J
RS1/16S104J
RS1/16S104J
RS1/16S104J
R
R
R
R
R
414
416
417
418
419
(A,31,78)
(B,23,44)
(B,24,42)
(B,26,42)
(A,31,84)
RS1/16S103J
RS1/16SS473J
RS1/16S225J
RS1/16S104J
RS1/16S103J
R
R
R
R
R
537
540
541
542
543
(B,52,27)
(B,35,20)
(A,33,31)
(A,32,31)
(A,33,34)
RS1/16S104J
RS1/16S103J
RS1/16S104J
RS1/16S104J
RS1/16S104J
R
R
R
R
R
420
421
423
424
425
(B,23,41)
(B,46,40) 22Ω
(A,45,88)
(A,46,79)
(A,42,89)
RS1/16S103J
CCN1111
RS1/16S1002D
RS1/16S272J
RS1/16S103J
R
R
R
R
R
544
551
556
601
602
(A,32,36)
(B,49,27)
(A,22,18)
(B,26,95)
(B,20,88)
RS1/16S104J
RS1/16S220J
RS1/16SS102J
RS1/16S103J
RS1/16S154J
R
R
R
R
R
426
427
428
429
430
(A,38,88)
(A,39,91)
(A,41,76)
(A,39,92)
(A,44,79)
RS1/16S472J
RS1/16S103J
RS1/16S472J
RS1/16S0R0J
RS1/16S472J
R
R
R
R
R
604
606
608
609
610
(B,20,87)
(B,20,85)
(B,32,82)
(B,31,79)
(B,28,84)
RS1/16S154J
RS1/16S154J
RS1/16S303J
RS1/16S153J
RS1/16S303J
R
R
R
R
R
431
432
433
434
435
(A,37,86)
(B,45,31)
(A,31,79)
(A,30,84)
(A,24,25)
RS1/16S472J
RS1/16S0R0J
RS1/16S223J
RS1/16S223J
RS1/16SS104J
R
R
R
R
R
611
612
613
615
702
(B,20,82)
(B,21,78)
(B,20,78)
(B,21,80)
(A,84,40) 22Ω
RS1/16S153J
RS1/16S153J
RS1/16S153J
RS1/16S153J
CCN1111
R
R
R
R
R
436
439
440
441
442
(B,37,13) 22Ω
(B,31,24)
(B,32,24)
(B,30,24)
(A,36,87)
CCN1111
RS1/16S220J
RS1/16S220J
RS1/16S103J
RS1/16S103J
R
R
R
R
R
703
704
705
707
708
(A,80,40) 22Ω
(B,41,9) 22Ω
(B,51,7) 22Ω
(A,70,40)
(B,52,13) 22Ω
CCN1111
CCN1111
CCN1111
RS1/16S220J
CCN1111
A
B
C
XDV-M8357ZT/UC
5
6
7
8
D
E
F
57
1
Circuit Symbol and No.
A
B
2
3
Part No.
4
Circuit Symbol and No.
Part No.
R
R
R
R
R
709
710
712
713
714
(A,56,29)
(A,53,26)
(A,93,10)
(A,92,37)
(A,90,37)
RS1/16S0R0J
RS1/16S102J
RS1/16S103J
RS1/16S220J
RS1/16S220J
R
R
R
R
R
1035
1036
1038
1039
1040
(B,71,85)
(B,73,86)
(B,64,89)
(B,66,87)
(B,68,88)
RS1/16SS473J
RS1/16SS473J
RS1/16SS473J
RS1/16SS473J
RS1/16SS473J
R
R
R
R
R
723
724
726
727
728
(A,91,18)
(A,94,16)
(A,70,4)
(A,66,4)
(A,64,5)
RS1/16S0R0J
RS1/16SS473J
RS1/16SS473J
RS1/16SS473J
RS1/16SS473J
R
R
R
R
R
1041
1042
1046
1200
1202
(B,50,74)
(A,56,71)
(B,94,86)
(A,104,71)
(A,102,73)
RS1/16S0R0J
RS1/16SS473J
RS1/16S0R0J
RS1/16S0R0J
RS1/16S201J
R
R
R
R
R
734
737
739
740
741
(A,93,24) 10kΩ
(A,72,39)
(A,57,24)
(A,57,20)
(A,57,14)
CCN1125
RS1/16S103J
RS1/16S103J
RS1/16S103J
RS1/16S103J
R
R
R
R
R
1212
1218
1219
1220
1221
(A,85,60)
(A,76,98)
(A,73,101)
(A,85,100)
(A,81,100)
RS1/16S220J
RS1/16S2701D
RS1/16S1600D
RS1/16S2701D
RS1/16S2201D
R
R
R
R
R
742
743
768
769
789
(A,55,10)
(A,57,12)
(A,12,26)
(A,25,29)
(B,53,30)
RS1/16S103J
RS1/16S103J
RA3C221J
RS1/16SS221J
RS1/16S0R0J
R
R
R
R
R
1222
1223
1224
1230
1231
(A,85,99)
(A,84,100)
(A,83,100)
(A,104,69)
(B,92,70)
RS1/16S0R0J
RS1/16S2701D
RS1/16S2201D
RS1/16SS473J
RS1/16SS473J
R
R
R
R
R
790
791
792
793
794
(B,84,25) 10Ω
(B,87,6)
(B,84,7)
(B,82,7)
(B,77,8)
CCN1133
RA3C100J
RS1/16S100J
RS1/16S100J
RS1/16S100J
R
R
R
R
R
1232
1233
1235
1236
1237
(A,84,59)
(A,82,59)
(A,65,93)
(B,72,99)
(B,69,98)
RS1/16SS473J
RS1/16SS473J
RS1/16S0R0J
RS1/16S0R0J
RS1/16S0R0J
R
R
R
R
R
795
1000
1001
1002
1003
(B,81,24)
(B,75,58)
(B,83,55)
(B,90,85)
(B,62,86)
RS1/16S100J
RS1/16SS473J
RS1/16SS473J
RS1/16SS473J
RS1/16SS473J
R
R
R
R
R
1500
1501
1503
1506
1507
(A,75,104)
(A,71,109)
(A,71,106)
(B,66,112)
(A,72,111)
RS1/16S222J
RS1/16S152J
RS1/16S3300D
RS1/16S0R0J
RS1/16S101J
R
R
R
R
R
1004
1005
1006
1007
1008
(B,62,88)
(B,64,87)
(B,76,86) 47kΩ
(B,49,79)
(A,53,76)
RS1/16SS473J
RS1/16SS473J
CCN1131
RA3C471J
RS1/16S472J
R
R
R
R
R
1510
1513
1514
1515
1516
(A,78,111)
(A,45,110)
(A,49,106)
(A,62,114)
(A,59,113)
RS1/16S222J
RS1/16S622J
RS1/16S622J
RS1/16S622J
RS1/16S622J
R
R
R
R
R
1009
1010
1011
1012
1013
(B,50,73)
(B,50,70)
(B,48,68) 47kΩ
(A,54,69)
(B,48,65)
RS1/16S103J
RS1/16SS473J
CCN1131
RS1/16S102J
RS1/16S470J
R
R
R
R
R
1517
1518
1519
1520
1521
(A,48,115)
(A,49,107)
(A,46,112)
(A,48,110)
(A,58,107)
RS1/16S622J
RS1/16S622J
RS1/16S622J
RS1/16S622J
RS1/16S622J
R
R
R
R
R
1014
1015
1016
1017
1018
(B,48,63) 47kΩ
(A,56,55)
(B,58,57)
(B,59,55)
(B,57,55)
CCN1131
RS1/16S332J
RS1/16SS473J
RS1/16SS473J
RA3C473J
R
R
R
R
R
1522
1523
1524
1525
1526
(A,57,114)
(A,58,109)
(A,59,111)
(A,86,120)
(A,88,120)
RS1/16S622J
RS1/16S622J
RS1/16S622J
RS1/16S101J
RS1/16S101J
R
R
R
R
R
1019
1020
1021
1022
1023
(A,83,104)
(A,86,103)
(B,79,91)
(B,95,92)
(B,95,94)
RS1/16S105J
RS1/16S102J
RS1/8S470J
RS1/8S470J
RS1/8S470J
R
R
R
R
R
1611
1612
1700
1701
1702
(A,92,121)
(A,92,120)
(A,112,16)
(A,114,20)
(B,89,31)
RS1/16S0R0J
RS1/16S0R0J
RS1/16SS473J
RS1/16SS473J
RS1/16SS473J
R
R
R
R
R
1025
1026
1027
1028
1029
(B,101,88)
(B,75,92)
(B,73,102)
(B,102,99)
(B,79,38)
RS1/16S0R0J
RS1/16S0R0J
RS1/16S0R0J
RS1/16S0R0J
RS1/16SS473J
R
R
R
R
1703
1704
1705
1708
(B,97,39)
(A,95,37)
(B,89,29)
(B,94,17)
RS1/16SS473J
RS1/16SS473J
RS1/16SS473J
RS1/16SS473J
R
R
R
R
R
1030
1031
1032
1033
1034
(B,57,87) 47kΩ
(B,85,31)
(B,60,88)
(A,56,78)
(B,70,85)
CCN1131
RS1/16SS473J
RS1/16SS473J
RS1/16S472J
RS1/16SS473J
C
D
E
CAPACITORS
F
58
C
C
C
C
101
102
103
104
(A,11,51)
(A,19,47)
(B,21,66)
(B,35,69)
CKSRYB333K16
CKSRYB333K16
CKSSYB104K10
CSZSR100M16
XDV-M8357ZT/UC
1
2
3
4
5
Circuit Symbol and No.
6
7
Part No.
Circuit Symbol and No.
8
Part No.
C 105
(B,38,68)
CKSRYB103K50
C 212
(A,50,40)
CKSQYB105K16
C
C
C
C
C
106
107
108
109
110
(A,23,42)
(A,20,39)
(B,30,75)
(B,35,75)
(A,23,34)
CEVW220M6R3
CKSRYB103K50
CKSRYB103K50
CSZSR100M16
CKSRYB333K16
C
C
C
C
C
213
214
220
222
223
(A,49,35)
(A,52,42)
(B,67,26)
(B,71,28)
(B,71,26)
CCSRCH180J50
CKSRYB102K50
CKSRYB102K50
CCSRCH150J50
CKSRYB103K50
C
C
C
C
C
111
112
113
114
115
(A,17,39)
(B,23,73)
(A,10,36)
(B,28,67)
(A,12,39)
CKSRYB183K25
CSZSR470M6R3
CKSRYB103K50
CKSRYB103K50
CEVW220M6R3
C
C
C
C
C
224
225
226
228
229
(B,71,24)
(B,63,31)
(B,66,16)
(B,60,16)
(B,63,21)
CKSRYB103K50
CKSRYB333K16
CKSRYB104K16
CCSRCH470J50
CKSRYB104K16
C
C
C
C
C
116
117
119
120
121
(B,31,68)
(B,24,63)
(A,28,58)
(B,29,66)
(A,28,54)
CKSSYB104K10
CSZSR2R2M20
CSZSR470M6R3
CKSRYB103K50
CSZSR1R0M35
C
C
C
C
C
230
231
232
233
262
(B,60,21)
(B,67,13)
(B,58,6)
(B,58,12)
(A,44,44)
CKSRYB104K16
CKSRYB333K16
CSZSR1R0M35
CKSRYB104K16
CKSSYB104K10
C
C
C
C
C
122
123
124
125
126
(B,30,64)
(B,31,64)
(B,22,66)
(B,31,66)
(B,33,48)
CKSSYB104K10
CKSSYB104K10
CKSRYB105K6R3
CKSRYB102K50
CKSSYB104K10
C
C
C
C
C
301
302
306
307
309
(B,36,88)
(B,32,97)
(B,25,97)
(B,19,105)
(B,51,87)
CKSRYB104K16
CKSRYB224K10
CKSSYB104K10
CKSSYB104K10
CKSRYB103K50
C
C
C
C
C
127
128
129
130
131
(B,33,66)
(B,37,62)
(B,41,52)
(B,41,55)
(B,41,56)
CKSRYB102K50
CKSRYB102K50
CSZSR100M16
CKSRYB222K50
CKSRYB222K50
C
C
C
C
C
310
311
312
313
314
(B,53,90)
(B,22,101)
(B,50,84)
(B,42,79)
(B,50,98)
CSZSR100M16
CKSRYB123K25
CKSRYB103K50
CSZSR100M16
CKSRYB153K25
C
C
C
C
C
132
133
134
135
136
(B,42,59)
(B,38,61)
(A,32,63)
(B,43,45)
(B,47,55)
CSZSR100M16
CKSSYB104K10
CEVW101M10
CKSSYB104K10
CCSRCH101J50
C
C
C
C
C
319
320
322
323
324
(B,36,93)
(A,44,94)
(B,35,85)
(B,24,13)
(B,35,97)
CKSRYB103K50
CEVW101M10
CCSRCH101J50
CKSQYB224K16
CKSRYB472K50
C
C
C
C
C
137
138
139
140
141
(A,32,57)
(A,32,56)
(A,32,55)
(A,33,53)
(A,47,55)
CKSRYB222K50
CKSRYB222K50
CKSRYB222K50
CKSRYB222K50
CKSRYB103K50
C
C
C
C
C
350
351
352
353
354
(A,22,8)
(B,17,95)
(B,15,98)
(B,13,88)
(B,51,38)
CEVW220M10
CKSSYB104K10
CCSRCH101J50
CKSRYB103K50
CKSQYB334K16
C
C
C
C
C
142
143
144
145
146
(A,52,53)
(A,49,61)
(A,40,59)
(A,41,59)
(A,43,59)
CKSRYB332K50
CKSRYB333K16
CCSRCH121J50
CCSRCH121J50
CCSRCH121J50
C
C
C
C
C
355
356
357
358
359
(A,60,39)
(B,13,80)
(B,62,39)
(B,63,42)
(B,57,36)
CCSRCH161J50
CKSSYB104K10
CKSRYB223K25
CKSRYB472K50
CKSRYB104K16
C
C
C
C
C
147
148
149
150
151
(A,46,59)
(A,47,59)
(A,45,72)
(A,46,72)
(A,37,67)
CCSRCH121J50
CCSRCH121J50
CCSRCH471J50
CKSRYB333K16
CSZSR100M16
C
C
C
C
C
360
370
401
402
403
(B,64,39)
(B,12,105)
(A,42,45)
(A,31,42)
(A,36,71)
CKSSYB104K10
CKSRYB104K16
CKSRYB333K16
CKSRYB103K50
CKSRYB103K50
C
C
C
C
C
152
153
154
155
156
(A,51,67)
(A,51,70)
(A,40,71)
(B,51,56)
(B,52,45)
CKSRYB103K50
CKSRYB103K50
CKSRYB103K50
CCSRCH821J50
CCSRCH151J50
C
C
C
C
C
404
406
409
410
411
(B,37,44)
(B,29,101)
(B,26,46)
(A,30,39)
(A,31,39)
CKSRYB333K16
CKSRYB273K25
CKSRYB153K25
CKSRYB103K50
CKSRYB102K50
C
C
C
C
C
157
158
159
160
162
(B,50,44)
(A,44,57)
(A,28,71)
(A,32,72)
(A,49,74)
CKSRYB333K16
CKSRYB103K50
CKSSYB104K10
CEVW470M10
CSZSR220M10
C
C
C
C
C
412
414
415
417
418
(B,36,45)
(B,32,44)
(B,22,42)
(A,44,82)
(A,33,41)
CKSRYB104K16
CKSSYB104K10
CCSRCH470J50
CKSRYB103K50
CCSRCH101J50
C
C
C
C
163
208
209
211
(A,28,68)
(A,52,48)
(A,46,45)
(A,51,36)
CKSRYB102K50
CKSRYB822K50
CKSSYB104K10
CCSRCH7R0D50
C
C
C
C
419
421
422
424
(B,43,37)
(B,24,36)
(B,24,37)
(B,25,33)
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
XDV-M8357ZT/UC
5
6
7
8
A
B
C
D
E
F
59
1
Circuit Symbol and No.
A
B
C
D
E
F
2
3
Part No.
4
Circuit Symbol and No.
Part No.
C 425
(B,21,32)
CSZSR100M16
C 1000
(B,76,59)
CKSSYB104K10
C
C
C
C
C
426
427
428
429
430
(B,44,30)
(B,34,24)
(B,38,24)
(B,41,24)
(B,41,26)
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CSZSR100M16
CKSSYB104K10
C
C
C
C
C
1001
1002
1003
1004
1005
(A,77,46)
(B,83,51)
(B,82,48)
(B,82,29)
(B,84,39)
CEVW101M6R3
CKSSYB104K10
CKSYB106K6R3
CKSSYB104K10
CSZSR100M16
C
C
C
C
C
431
432
435
442
450
(A,40,89)
(B,46,28)
(A,42,88)
(A,34,88)
(A,35,38)
CKSRYB103K50
CCSRCH101J50
CCSRCH101J50
CKSRYB273K25
CKSRYB152K50
C
C
C
C
C
1006
1007
1008
1009
1010
(A,85,46)
(B,84,36)
(B,70,42)
(B,75,36)
(B,75,33)
CEVW4R7M35
CKSSYB104K10
CKSSYB104K10
CKSQYB224K25
CKSQYB224K25
C
C
C
C
C
501
502
503
504
505
(B,55,22)
(A,54,22)
(A,55,18)
(A,54,19)
(A,47,31)
CKSRYB103K50
CKSSYB104K10
CKSRYB473K16
CKSRYB473K16
CKSRYB103K50
C
C
C
C
C
1011
1012
1014
1015
1016
(B,82,86)
(B,86,85)
(B,54,84)
(B,65,87)
(B,65,56)
CKSYB106K6R3
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSYB106K6R3
C
C
C
C
C
506
507
508
510
511
(B,39,20)
(A,37,6)
(B,37,7)
(B,45,19)
(B,56,18)
CKSSYB104K10
CKSSYB104K10
CSZSR100M16
CKSRYB103K50
CKSRYB103K50
C
C
C
C
C
1018
1019
1020
1021
1022
(B,52,82)
(B,51,81)
(B,50,76)
(B,50,75)
(B,50,71)
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
C
C
C
C
C
512
520
602
604
606
(B,42,21)
(B,38,18)
(B,20,90)
(B,20,91)
(B,22,84)
CKSRYB102K50
CKSRYB104K16
CKSRYB104K16
CKSRYB104K16
CKSRYB104K16
C
C
C
C
C
1023
1024
1025
1026
1027
(B,78,72)
(A,56,57)
(B,65,58)
(B,80,96)
(B,85,97)
CKSSYB104K10
CCSRCH100D50
CKSSYB104K10
CSZSR100M16
CKSSYB104K10
C
C
C
C
C
608
610
612
701
702
(B,25,91)
(B,25,84)
(B,26,75)
(A,78,38)
(A,74,38)
CKSRYB104K16
CKSRYB104K16
CKSRYB104K16
CKSSYB104K10
CKSSYB104K10
C
C
C
C
C
1028
1029
1030
1031
1032
(A,94,106)
(A,54,59)
(A,68,98)
(A,69,98)
(B,94,88)
CCSRCH180J50
CKSSYB104K10
CKSSYB104K10
CCSRCH101J50
CKSSYB104K10
C
C
C
C
C
703
704
705
706
707
(A,64,39)
(A,91,34)
(A,57,35)
(A,90,31)
(B,75,27)
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
C
C
C
C
C
1033
1034
1035
1036
1037
(B,77,101)
(B,101,95)
(B,63,93)
(A,56,77)
(B,81,100)
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSRYB103K50
CKSSYB104K10
C
C
C
C
C
708
709
710
711
712
(A,57,26)
(A,58,45)
(A,57,25)
(A,93,21)
(A,56,21)
CKSSYB104K10
CEVW101M4
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
C
C
C
C
C
1038
1039
1040
1041
1061
(B,86,97)
(B,88,97)
(B,98,87)
(B,86,88)
(B,79,58)
CCSRCH510J50
CCSRCK1R0C50
CKSSYB104K10
CKSSYB104K10
CKSYB106K6R3
C
C
C
C
C
714
715
716
717
718
(A,91,13)
(A,90,8)
(A,57,8)
(A,82,5)
(A,73,5)
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
C
C
C
C
C
1200
1201
1202
1203
1204
(A,103,82)
(A,103,78)
(A,101,60) 68µF/6.3V
(A,103,75)
(A,101,64)
CKSSYB104K10
CKSSYB104K10
CCH1385
CKSSYB104K10
CKSSYB104K10
C
C
C
C
C
719
720
721
722
723
(A,68,4)
(A,66,45)
(A,67,41)
(B,70,17)
(A,13,23)
CKSSYB104K10
CEVW101M4
CKSSYB104K10
CKSRYB103K50
CKSSYB104K10
C
C
C
C
C
1205
1206
1207
1208
1209
(B,100,61)
(B,92,78)
(B,92,74)
(A,102,80)
(A,101,71)
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
C
C
C
C
C
729
801
802
803
806
(A,59,4)
(A,88,38)
(B,31,82)
(B,22,82)
(A,22,29)
CCSRCH101J50
CCSRCH101J50
CCSRCH101J50
CCSRCH221J50
CCSSCH101J50
C
C
C
C
C
1210
1211
1212
1213
1214
(A,102,88)
(A,94,63)
(A,94,97)
(A,88,60)
(A,86,97)
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
C
C
C
C
807
808
809
810
(A,16,21)
(B,91,13)
(A,23,25)
(A,17,20)
CKSSYB104K10
CKSYB106K6R3
CKSSYB104K10
CKSSYB104K10
C
C
C
C
1215
1216
1217
1218
(A,85,63)
(A,80,97)
(A,85,50)
(A,78,98)
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
60
XDV-M8357ZT/UC
1
2
3
4
5
Circuit Symbol and No.
6
7
Part No.
8
Circuit Symbol and No.
Part No.
F
Unit Number:CWX3198
C 1219
(A,90,100)
CEVW470M4
C
C
C
C
C
1220
1221
1222
1223
1224
(A,77,63)
(A,78,100)
(A,74,97)
(A,85,113) 68µF/6.3V
(A,73,99)
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CCH1385
CKSQYB105K16
C
C
C
C
C
1225
1226
1227
1228
1229
(A,92,114)
(A,73,59)
(A,67,70)
(A,68,80)
(A,68,90)
CEVW221M4
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
IC 3101
IC 3102
IC 3131
IC 3301
IC 3311
(B,169,17) IC
(B,169,10) IC
(B,45,20) IC
(B,154,13) IC
(B,150,13) IC
NJM2068MD
NJM2068MD
TC74HC4066AF
NJM2235V
NJM2267V
C
C
C
C
C
1230
1231
1232
1233
1234
(A,102,102) 68µF/6.3V
(A,98,104)
(A,66,55)
(A,97,41)
(A,65,74)
CCH1385
CKSRYB103K50
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
IC 3601
IC 3631
IC 3811
IC 3821
IC 3831
(B,171,34)
(A,174,42)
(B,196,39)
(A,206,28)
(A,194,12)
PE5272A
HA12187FP
PAJ002A
BA00AST
BA08SFP
C
C
C
C
C
1235
1500
1501
1502
1503
(A,66,80)
(A,64,104)
(A,65,104)
(A,62,103)
(A,68,103)
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CSZSR100M16
CSZSR100M16
IC 3851
IC 3871
IC 3891
Q 3131
Q 3151
(A,145,29) IC
(A,138,45) IC
(A,202,12) IC
(B,53,19) Transistor
(B,184,12) Transistor
BA9706K
PQ20VZ11
PQ20VZ11
UMD12N
DTC323TU
C
C
C
C
C
1504
1505
1507
1510
1511
(B,59,101)
(B,56,104)
(A,78,104)
(A,66,109)
(B,65,110)
CSZSR100M16
CKSSYB104K10
CKSRYB104K16
CSZSR100M16
CKSSYB104K10
Q
Q
Q
Q
Q
3152
3153
3154
3155
3201
(B,181,10) Transistor
(B,182,14) Transistor
(B,179,18) Transistor
(B,178,22) Transistor
(B,38,29) Transistor
DTC323TU
UMA2N
DTA114EU
DTA114EU
2SC2712
C
C
C
C
C
1512
1513
1514
1515
1516
(A,63,110)
(B,63,111)
(B,59,105)
(A,51,84)
(B,63,95)
CSZSR100M16
CKSSYB104K10
CSZSR100M16
CKSRYB104K16
CKSRYB104K16
Q
Q
Q
Q
Q
3301
3601
3811
3812
3813
(B,157,18)
(A,174,31)
(A,206,40)
(B,187,41)
(A,194,39)
Transistor
Transistor
Transistor
Transistor
Transistor
DTC144EU
DTA144EK
2SB942A
DTC143TU
DTC143EU
C
C
C
C
C
1517
1518
1519
1520
1521
(A,54,101)
(A,55,94)
(A,50,94)
(A,49,101)
(A,53,114)
CEVWNP4R7M16
CEVWNP4R7M16
CEVWNP4R7M16
CEVWNP4R7M16
CKSRYB104K16
Q
Q
Q
Q
Q
3814
3821
3851
3852
3853
(B,190,32)
(B,198,32)
(A,127,26)
(A,134,34)
(B,147,24)
Transistor
Transistor
Transistor
Transistor
Transistor
DTC143TU
DTC114EU
2SA1731
2SA1731
DTC114EU
C
C
C
C
C
1522
1523
1524
1525
1526
(A,46,110)
(A,59,114)
(A,48,112)
(A,57,111)
(A,52,107)
CCSRCH331J50
CCSRCH331J50
CCSRCH221J50
CCSRCH221J50
CCSRCH221J50
Q
Q
Q
D
D
3880
3891
3931
3131
3141
(B,190,16) Transistor
(B,204,21) Transistor
(A,164,28) Transistor
(B,52,24) Diode
(B,38,17) Diode
2SA1162
DTC114EU
DTA143XU
MA113
RD24M(B2)
C
C
C
C
C
1527
1531
1532
1601
1602
(A,55,107)
(B,53,104)
(B,53,102)
(A,30,125)
(A,28,125)
CCSRCH221J50
CKSQYB334K16
CKSYB475K10
CKSRYB473K25
CKSRYB473K25
D
D
D
D
D
3142
3143
3144
3201
3321
(B,34,23)
(B,34,16)
(B,34,19)
(B,21,20)
(B,27,27)
Diode
Diode
Diode
Diode
Diode
RD24M(B2)
RD24M(B2)
RD24M(B2)
RD24M(B2)
UDZ18(B)
3322
3323
3324
3631
3632
(B,24,27)
(A,33,34)
(A,30,36)
(B,18,40)
(B,16,40)
Diode
Diode
Diode
Diode
Diode
UDZ18(B)
UDZ18(B)
UDZ18(B)
UDZ18(B)
UDZ18(B)
A
Unit Name:Extension Unit
MISCELLANEOUS
IC
IC
IC
IC
IC
C
C
C
C
C
1603
1701
1702
1703
1704
(A,27,125)
(B,100,19)
(A,115,21)
(A,115,17)
(B,98,39)
CKSRYB473K25
CKSSYB104K10
CKSSYB104K10
CSZSR100M16
CKSSYB104K10
D
D
D
D
D
C
C
C
C
C
1705
1709
1710
1711
1712
(B,100,41)
(A,98,27)
(A,105,31)
(A,97,39)
(A,63,59)
CSZSR100M16
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
CKSSYB104K10
D
D
D
D
D
3801
3821
3831
3851
3852
(A,51,8) Diode
(B,184,23) Diode
(B,195,9) Diode
(B,127,25) Diode
(B,133,33) Diode
UDZ18(B)
MA132WK
HZU4R3(B3)
RB051L-40
RB051L-40
C 1713
C 2000
C 2001
(A,102,39)
(A,14,45)
(A,17,23)
CKSSYB104K10
CKSRYB104K16
CKSRYB104K16
D
D
L
L
3880
3931
3101
3102
(B,190,20)
(A,167,27)
(B,184,17)
(B,190,10)
MA147
MA111
CTF1473
CTF1473
Diode
Diode
Inductor
Inductor
6
7
C
D
E
F
XDV-M8357ZT/UC
5
B
8
61
1
Circuit Symbol and No.
A
B
2
Part No.
L 3301
(A,161,15) Inductor
CTF1473
L 3801
L 3851
L 3853
TH3601
X 3601
(A,19,42) Inductor
CTF1473
(A,136,26) Coil
CTH1238
(A,125,34) Coil
CTH1238
(A,182,29) Thermistor
CCX1055
(B,184,35) Ceramic Resonator 6.290MHz CSS1305
>FU3803
>FU3804
EF3301
EF3302
EF3801
(A,120,36) Fuse 1.5A
(B,118,44) Fuse 1.5A
(A,32,28) EMI Filter
(A,29,28) EMI Filter
(B,104,21) EMI Filter
ICPS1R2
ICPS1R2
CCG1076
CCG1076
CCG1051
EF3802
EF3831
EF3851
(A,104,21) EMI Filter
(A,208,11) EMI Filter
(A,116,21) EMI Filter
CCG1051
CCG1051
CCG1051
RESISTORS
C
D
E
R
R
R
R
R
3101
3102
3105
3106
3107
(B,185,8)
(B,183,8)
(B,174,16)
(B,175,9)
(B,175,18)
RS1/16S472J
RS1/16S472J
RS1/16S103J
RS1/16S103J
RS1/16S163J
R
R
R
R
R
3108
3109
3110
3111
3112
(B,175,12)
(B,170,20)
(B,170,13)
(B,163,17)
(B,163,10)
RS1/16S163J
RS1/16S103J
RS1/16S103J
RS1/16S103J
RS1/16S103J
R
R
R
R
R
3113
3114
3115
3116
3120
(A,165,20)
(A,165,12)
(A,165,17)
(A,168,10)
(A,119,10)
RS1/16S750J
RS1/16S750J
RS1/16S750J
RS1/16S750J
RS1/16S0R0J
R
R
R
R
R
3121
3122
3125
3126
3127
(A,116,9)
(A,116,10)
(A,165,19)
(A,165,11)
(A,165,15)
RS1/16S0R0J
RS1/16S0R0J
RS1/16S100J
RS1/16S100J
RS1/16S100J
R
R
R
R
R
3128
3131
3132
3141
3142
(A,165,9)
(B,53,22)
(B,51,17)
(A,34,18)
(A,34,22)
RS1/16S100J
RS1/16S102J
RS1/16S103J
RS1/8S510J
RS1/8S510J
R
R
R
R
R
3143
3144
3151
3152
3154
(A,34,16)
(A,34,20)
(B,179,14)
(B,178,14)
(B,181,16)
RS1/8S510J
RS1/8S510J
RS1/16S223J
RS1/16S223J
RS1/16S102J
R
R
R
R
R
3155
3201
3202
3203
3301
(B,178,20)
(B,21,15)
(B,42,28)
(B,45,28)
(B,156,8)
RS1/16S102J
RS1/4S221J
RS1/16S103J
RS1/16S103J
RS1/16S223J
R
R
R
R
R
3302
3312
3321
3322
3323
(B,157,13)
(A,148,13)
(B,141,10)
(A,30,34)
(B,157,14)
RS1/16S104J
RS1/16S101J
RS1/10S750J
RS1/10S750J
RS1/16S105J
R 3324
R 3325
R 3326
(B,157,11)
(B,147,9)
(B,153,8)
RS1/16S105J
RS1/16S105J
RS1/16S221J
F
62
3
4
Circuit Symbol and No.
Part No.
R 3327
R 3602
(B,146,14)
(A,182,31)
RS1/16S105J
RS1/16S683J
R
R
R
R
R
3603
3605
3607
3611
3612
(A,179,29)
(B,185,28)
(A,163,40)
(A,179,28)
(A,169,35)
RS1/16S104J
RS1/16S104J
RS1/16S102J
RS1/16S104J
RS1/16S104J
R
R
R
R
R
3613
3614
3615
3616
3618
(A,169,37)
(A,169,38)
(A,182,36)
(A,175,35)
(A,180,36)
RS1/16S104J
RS1/16S104J
RS1/16S104J
RS1/16S104J
RS1/16S104J
R
R
R
R
R
3619
3620
3621
3625
3626
(B,182,40)
(B,181,45)
(B,180,45)
(A,173,27)
(B,182,27)
RS1/16S333J
RS1/16S104J
RS1/16S102J
RS1/16S104J
RS1/16S104J
R
R
R
R
R
3627
3628
3629
3630
3631
(B,182,28)
(A,174,25)
(A,177,26)
(A,165,40)
(B,18,35)
RS1/16S393J
RS1/16S333J
RS1/16S104J
RS1/16S104J
RS1/4S101J
R
R
R
R
R
3632
3634
3640
3646
3653
(B,15,35)
(A,168,40)
(B,184,42)
(B,161,27)
(B,166,24)
RS1/4S101J
RS1/16S104J
RS1/10S0R0J
RS1/16S102J
RS1/16S331J
R
R
R
R
R
3656
3657
3658
3660
3661
(B,160,31)
(B,160,33)
(B,173,22)
(B,163,25)
(A,160,24)
RS1/16S102J
RS1/16S102J
RS1/16S0R0J
RS1/16S102J
RS1/16S102J
R
R
R
R
R
3662
3801
3802
3803
3804
(A,181,26)
(A,193,42)
(B,191,36)
(A,192,40)
(A,190,40)
RS1/16S102J
RS1/16S184J
RS1/16S7502D
RS1/16S2203D
RS1/16S1103D
R
R
R
R
R
3805
3806
3807
3808
3809
(B,190,41)
(B,190,42)
(B,33,9)
(B,34,12)
(A,192,42)
RS1/16S2203D
RS1/16S1103D
RS1/4S152J
RS1/4S472J
RS1/16S0R0J
R
R
R
R
R
3810
3811
3812
3813
3814
(A,193,37)
(A,198,44)
(B,203,40)
(B,202,40)
(B,202,37)
RS1/16S0R0J
RS1/4S2R7J
RS1/16S102J
RS1/16S104J
RS1/16S104J
R
R
R
R
R
3815
3816
3817
3818
3819
(B,190,44)
(A,189,40)
(B,190,39)
(A,19,45)
(A,19,44)
RS1/16S133J
RS1/16S133J
RS1/16S334J
RS1/16S102J
RS1/16S102J
R
R
R
R
R
3821
3822
3823
3824
3831
(B,202,24)
(B,203,32)
(B,202,32)
(B,200,32)
(B,192,19)
RS1/16S104J
RS1/16S1002D
RS1/16S1601D
RS1/16S1001D
RS1/16S271J
R 3833
R 3851
R 3852
(B,197,12)
(B,144,28)
(B,143,33)
RS1/16S104J
RS1/16S220J
RS1/16S560J
XDV-M8357ZT/UC
1
2
3
4
5
Circuit Symbol and No.
6
Part No.
R 3853
R 3854
(B,144,36)
(B,147,31)
RS1/16S2702D
RS1/16S151J
R
R
R
R
R
3855
3856
3857
3858
3859
(B,148,28)
(B,144,35)
(A,148,35)
(B,153,28)
(B,149,34)
RS1/16S4702D
RS1/16S1602D
RS1/16S102J
RS1/16S1502D
RS1/16S273J
R
R
R
R
R
3860
3861
3862
3863
3864
(B,144,32)
(A,153,32)
(A,152,35)
(B,144,29)
(A,150,34)
RS1/16S473J
RS1/16S151J
RS1/16S273J
RS1/16S473J
RS1/16S751J
R
R
R
R
R
3865
3866
3867
3868
3869
(A,152,28)
(A,143,36)
(B,141,31)
(B,141,28)
(B,147,25)
RS1/16S512J
RS1/16S101J
RS1/16S104J
RS1/16S202J
RS1/16S473J
R
R
R
R
R
3870
3871
3872
3873
3874
(B,151,28)
(B,149,28)
(B,147,35)
(B,147,36)
(A,145,45)
RS1/16S132J
RS1/16S272J
RS1/16S182J
RS1/16S272J
RS1/16S1301D
R
R
R
R
R
3875
3876
3880
3891
3892
(A,146,46)
(B,144,27)
(B,188,19)
(B,201,16)
(B,201,18)
RS1/16S1201D
RS1/16S0R0J
RS1/16S133J
RS1/16S7501D
RS1/16S1001D
R
R
R
R
R
3893
3894
3931
3964
3965
(B,201,19)
(A,207,16)
(B,118,21)
(A,56,38)
(A,54,37)
RS1/16S4700D
RS1/16S104J
RS1/8S241J
RS1/16S0R0J
RS1/16S221J
R
R
R
R
3966
3967
3968
3969
(A,53,39)
(A,51,39)
(A,50,37)
(A,49,40)
RS1/16S221J
RS1/16S221J
RS1/16S221J
RS1/16S221J
CAPACITORS
C
C
C
C
C
3101
3102
3107
3108
3109
(A,46,30)
(A,51,30)
(A,174,16)
(A,174,9)
(B,174,18)
CEVW4R7M35
CEVW4R7M35
CEVW4R7M35
CEVW4R7M35
CCSRCH560J50
C
C
C
C
C
3110
3111
3112
3113
3114
(B,174,12)
(B,165,20)
(B,164,13)
(B,164,17)
(B,164,10)
CCSRCH560J50
CKSRYB473K16
CKSRYB473K16
CCSRCH560J50
CCSRCH560J50
C
C
C
C
C
3115
3116
3117
3118
3125
(B,49,9)
(A,51,12)
(B,49,10)
(A,52,10)
(A,165,21)
CCSRCH102J25
CCSRCH102J25
CCSRCH102J25
CCSRCH102J25
CCSRCH471J50
C
C
C
C
C
3126
3127
3128
3131
3141
(A,165,13)
(A,165,16)
(A,166,8)
(B,51,22)
(A,40,18)
CCSRCH471J50
CCSRCH471J50
CCSRCH471J50
CKSRYB224K16
CEVWNP4R7M16
(A,40,23)
CEVWNP4R7M16
C 3142
7
Circuit Symbol and No.
8
Part No.
C
C
C
C
3143
3144
3201
3301
(A,47,15)
(A,45,20)
(B,41,28)
(A,149,9)
CEVWNP4R7M16
CEVWNP4R7M16
CKSRYB102K50
CEVW4R7M35
C
C
C
C
C
3302
3303
3304
3305
3306
(B,157,9)
(B,158,8)
(A,157,10)
(A,37,28)
(B,147,14)
CKSRYB104K16
CKSRYB102K50
CEVW101M10
CEVW4R7M35
CCSRCH470J50
C
C
C
C
C
3307
3308
3309
3310
3311
(A,162,19)
(B,146,7)
(B,152,17)
(B,157,16)
(A,44,37)
CSZSR1R0M35
CCSRCH470J50
CCSRCH470J50
CCSRCH470J50
CEVWNP4R7M16
C
C
C
C
C
3312
3313
3314
3315
3316
(B,147,17)
(A,156,18)
(B,149,7)
(A,142,9)
(A,144,15)
CKSRYB102K50
CEVW101M10
CKSYB475K10
CEVW220M16
CEVW101M10
C
C
C
C
C
3317
3601
3602
3603
3604
(A,135,13)
(A,174,33)
(A,179,36)
(B,178,45)
(A,176,33)
CEVW101M10
CKSRYB104K16
CKSRYB104K16
CKSRYB103K50
CKSRYB104K16
C
C
C
C
C
3606
3631
3632
3633
3801
(A,182,30)
(B,21,11)
(B,21,9)
(A,168,41)
(A,47,9)
CKSRYB104K16
CCSRCH201J50
CCSRCH201J50
CKSRYB104K16
CEVW1R0M50
C
C
C
C
C
3811
3812
3813
3814
3821
(A,190,46)
(B,192,45)
(A,192,36)
(A,200,39)
(A,201,25)
CEVW100M16
CKSRYB103K50
CKSRYB103K50
CEHVW101M6R3
CEHVW100M16
C
C
C
C
C
3822
3823
3824
3831
3832
(B,202,26)
(A,199,31)
(B,202,29)
(B,192,9)
(A,187,12)
CKSQYB334K16
CEHVW470M16
CKSQYB334K16
CKSRYB473K16
CEHVW101M6R3
C
C
C
C
C
3833
3834
3835
3851
3852
(A,196,21)
(A,189,22)
(B,195,12)
(B,134,26) 47µF/6.3V
(B,123,25) 10µF
CEHVW100M16
CEHVW470M16
CKSQYB334K16
CCH1372
CCG1138
C
C
C
C
C
3853
3854
3855
3856
3857
(B,125,34) 22µF
(B,129,34) 22µF
(B,136,33) 10µF
(A,144,36)
(A,146,36)
CCG1139
CCG1139
CCG1138
CKSRYB102K50
CKSRYB102K50
C
C
C
C
C
3858
3859
3860
3861
3862
(B,147,33)
(B,146,31)
(A,152,34)
(A,152,32)
(B,149,24)
CKSRYB683K16
CKSRYB822K50
CKSRYB822K50
CKSRYB473K16
CKSRYB473K25
C
C
C
C
C
3863
3864
3865
3866
3867
(B,153,24)
(A,152,30)
(A,152,27)
(A,15,47)
(B,143,25)
CKSYB106K6R3
CKSRYB104K16
CCSRCH151J50
CKSRYB473K25
CKSRYB473K25
C 3868
(A,152,24)
CEHVW100M16
B
XDV-M8357ZT/UC
5
6
A
7
8
C
D
E
F
63
1
Circuit Symbol and No.
A
3
Part No.
4
Circuit Symbol and No.
C
C
C
C
3869
3870
3871
3872
(B,144,31)
(A,15,51)
(A,147,43)
(A,152,46) 100µF/4V
CKSRYB105K6R3
CKSRYB473K25
CKSYB105K16
CCH1400
C
C
C
C
C
3873
3874
3891
3892
3893
(B,149,33)
(A,15,49)
(A,202,20)
(A,207,18)
(B,204,11) 22µF/12V
CKSRYB473K16
CKSRYB473K25
CEHVW100M16
CKSRYB473K25
CCH1359
(A,125,12)
CKSRYB473K16
C 3894
B
2
M 2
Motor Unit(TRAY)
Part No.
CXC1541
Miscellaneous Parts List
Fan Motor
PU Unit
Motor Unit(Carriage)
Motor(Spindle)
Motor Unit(ELV)
M 1
M 3
M 4
CXM1195
CGY2020
CXC1552
CXM1282
CXC1540
H
Unit Number:CWM6518
Unit Name:MF Unit
MISCELLANEOUS
D
D
D
L
2901
2902
2903
2901
Diode
Diode
Diode
Coil
5KP24A
GP30ML-6373
ERA15-02VH
CTH1113
CAPACITORS
C
C
C
C
C
C
2901
2902
2903
2904
2905
2200µF/16V
2200µF/16V
3300µF/16V
3300µF/16V
3300µF/16V
CCH1383
CCH1383
CCH1384
CCH1384
CCH1384
A
Unit Number:
Unit Name:PCB Unit(A)
D
D 851
S 851
S 852
LED
Switch(DSP)
Spring Switch(TRP)
CN504-2
CSN1051
CSN1052
B
Unit Number:
Unit Name:PCB Unit(B)
S 301
VR301
VR302
R 301
R 302
Spring Switch(MAG)
Volume 10kΩ
Semi-fixed 1kΩ(B)
CSN1044
CCW1021
CCP1338
RS1/16S562J
RS1/16S622J
E
C 301
C 302
CKSRYB104K16
CKSRYB103K50
C
Unit Number:
Unit Name:PCB(A)
Q 851
F
Photo-transistor
PT4800
D
Unit Number:
Unit Name:PCB(B)
64
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
6. ADJUSTMENT
6.1 JIG CONNECTION DIAGRAM
A
DC Regulated +14.4V
Power Supply
+14.4V
0V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1. +B
2. NTSO
3. SG
4. SGND
5. CDL+
6. CDR+
7. NC
8. TXM+
9. NC
10. ACC
11. GND
12. NC
13. NC
14. NC
15. CDL16. CDR17. SGND
18. TXM19. NC
20. MUTE
B
15P EXTENSION CABLE
GGD1177
30P EXTENSION CABLE
GGD1171
C
This photo is XDV-M8006ZT.
On your service benches, the mechanism should be placed with
the magazine-slot side up unlike that shown in the photo.
D
Head Unit of TOYOTA
KEX-M9137ZT-02/UC, KEX-M9737ZT-02/UC
E
F
XDV-M8357ZT/UC
5
6
7
8
65
1
2
- Connection Diagram
4
EMV SYSTEM MODEL(/UC)
KEX-M9137ZT-02/UC(Pioneer AMP)
KEX-M9737ZT-02/UC(Mraklevinson AMP)
A
3
GEX-M8087XMZT/XU/UC
XM
TUNER
H/U
20P
20P
12P
20P
20P
12P
12P
EMV(DENSO)
12P
GGD1398
12P
B
6P
28P
26P
6P
28P
26P
12P
GGD1348
Bullet connector
(To DC Regulated Power Supply)
GM-9027ZT-02/E
Marklevinson AMP
Bullet connector
(To DC Regulated Power Supply)
AMP
C
25P
16P
25P
16P
GGD1240
Bullet connector
SP Line
D
NAVI ECU(DENSO)
GGD1169
FR-
FR+
AUI-
AUI+
18P
10P
18P
10P
RSA Controller
24P
XDV-M8357ZT/UC
E
24P
MDVD
20P
*MCD
20P
32P
*Please don't connect the MCD and MDVD at the same time
*MCD or MDVD does not operate if RSA controller is not connected.
F
66
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
6.2 MAIN UNIT ADJUSTMENT
A
- Connection Diagram
MAIN PCB(SIDE B)
DC V Meter
B
C
TC201
VCO
IC702
TC1000
IC1200
DSPCLK
D
Frequency
Counter
Setting state : Normal Mode, Without magazine
Item
Adjustment
Adjustment
point
Method
16MHz Master Clock TC1000
Frequency Counter :16.934400MHz ± 80Hz
VCO Offset
TC201
DC V Meter : 1.4V ± 0.2V
Symptoms at incomplete
adjustment
An image turns from a colored
one to a monochromatic one.
Too much misalignment will
result in no playback.
E
F
XDV-M8357ZT/UC
5
6
7
8
67
1
2
3
4
6.3 SKEW ADJUSTMENT
A
- If skew adjustment is necessary:
1) Replace the pickup unit by a new one.
2) Replace the spindle motor by a new one.
3) Replace the CRG chassis by a new one.
4) Replace the main shaft of the pickup unit by a new one.
5) Replace the sub shaft of the pickup unit by a new one.
* No skew adjustment is necessary for replacement of the CRG motor and the like.
- Procedures (Fig.1)
B
1) Remove the adhesive of the pickup unit with a pair of tweezers (above 2) to 5) only).
* Take care at this time that no fragments of the adhesive will be scattered, and that no unnatural force will apply
to the actuator.
2) Monitor the test point of the TP210 (RF waveform monitor) on the basis of GND in the product state with an
oscilloscope.
3) Clamp adjusting disc (GGV1018).
Skew adjusting screw
C
Adhesive
Coat the shaded portion (two locations)
with (adhesives).
D
Skew adjusting screw B
E
Adhesive
Actuator
Fig.1
F
68
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
4) Turn on the power in the test mode (F. Offset adjustment is found) and move the pickup to the vicinity of the
center of the disc.
5) Turn on the DVD LD and perform Focus Close.
6) Automatically adjust Tracking Balance and perform Tracking Close.
7) Observing RF waveform levels of an oscilloscope, slightly turn skew adjusting screw A and adjust the
oscilloscope so that the levels can be maximized. Repeat this operation three times and fix the levels where
they are maximized.
8) Mix agents A and B of adhesive 601 at a ratio of 1 to 1 and coat a specified part with both agents of the
adhesive. The adhesive is cured about 15 minutes. The coating position is shown in Fig.1.
A
Note) Do not apply the adhesive to the pickup section and the mechanical unit section other than the specified
part. Because heat is generated, do not mix a great number of adhesives at a time. Use the same number
of adhesives as the original one. Do not apply vibration until the adhesive is fixed.
B
9) Apply the screw lock to the head of the skew screw and secure it.
- Symptoms at incomplete adjustment
1) Deterioration of error rates
2) Large RF jitters: Waveforms are distorted.
3) Unstable tracking servo: There are such effects as leading-in and unstable servo.
- Connection Diagram
C
MAIN PCB(SIDE B)
Oscilloscope
D
TP210
E
IC702
IC1200
F
XDV-M8357ZT/UC
5
6
7
8
69
1
2
3
4
6.4 ELEVATION ADJUSTMENT
A
- This adjustment shall be performed when an error code 84 is displayed for an elevation error.
• Precautions
This mechanism unit uses a slide variable resistor to detect the height of the stage.
To absorb misalignment of the stage height due to unevenness of the DVD/CD mechanism unit and main unit,
the adjustment for each mechanism unit needs to be performed using semi-fixed resistors.
Because adjustment is performed on the production line, readjustment is not necessary usually. However, if an
elevation error occurs or when the slide variable resistor, spindle motor and CRG
chassis are replaced, elevation needs to be adjusted in the following procedures:
• Purpose
Adjust and check that the operation of elevation is normal.
B
• Adjustment method
• Measuring apparatus
• Measuring point
• Setting state
Oscilloscope, L.P.F. (one piece)
EREF or EPVO
Without magazine, test mode
Place the DVD/CD mechanism unit facedown (place the DVD/CD mechanism unit so
that the main unit may be set to the upper side).
C
MAIN UNIT
PCB UNIT(B)
EREF
VR302
EPVO
Oscilloscope
L.P.F.
47kΩ
1µF
D
• Check procedures
Display on head unit
For the flowchart of the test mode.
00800000
1. Enter the test mode and select a multiple DVD/CD player.
2. Set the mechanism unit test mode.
E
20400000
F
70
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
3. Move to the ELV/tray selection mode and press DISC key to select the ELV mode.
Key DISC
↑
4. Move to the operation mode selection.
5. When the DISC key is pressed, travel varies.
Note: If travel is set to Major, the stage
mechanical unit continues moving as
long as the DISC key is pressed.
If travel is set to Intermediate and
Key DISC
Minor, the stage mechanical unit
↑
moves whenever the DISC key is
pressed once.
↓
ELV/Tray select mode
↓
Key DISC
↓
Tray select
↓
Key DISC
↓
ELV/Tray select mode
↓
Key DISC
↓
ELV select
Display on head unit
A
70410000
Tray
00000001
70410000
ELV
↓
Operation mode select
↓
Key DISC
↓
Middle movement
↓
Key DISC
↓
Operation mode select
↓
Key DISC
↓
Maximum movement
↓
Key DISC
↓
Operation mode select
↓
Key DISC
↓
Minimum movement
00000000
B
70420000
00000001
70420000
C
00000002
70420000
00000000
D
6. Move to the motor forward revolution mode or motor reverse revolution
mode and align the magazine slot to graduations on the fourth disc (Fig. 2).
7. Adjustment
Adjust the potential difference between EREF and EPVO of PCB (B)
to 380 ± 20 mV with VR302.
Forward
revolution
70430000
Reverse
revolution
70440000
70450000
E
8. Termination of adjustment
Move to the mechanism-unit test termination mode and terminate
the mechanism-unit test mode.
F
XDV-M8357ZT/UC
5
6
7
8
71
1
2
3
4
9. Operation check
Terminate the test mode.
Place the mechanism unit horizontally (set the main unit to the drop side). At this time, take care of
short-circuiting of the PCB.
A
10. Check the height of the stage.
Press the DISC ± key to select DISC 4.
Check that the stopper bend of the clamping lever is fitted in the
groove of the frame stopper
section. (Fig. 3 to 5)
• Precautions
• The stopper bend to be clamped finally is clamped under the groove.
Check the stopper bend at
the position where it is fitted in the groove.
• Adjustment is completed if the stopper bend enters the center and is
clamped under the groove. Go to 14).
• If the stopper bend is dislocated, check misalignment. Go to 11).
11.
If the mechanism unit is dislocated:
Place the mechanism unit facedown.
When the mechanism unit is dislocated to the direction of the first disc,
turn VR302 counterclockwise. (Fig. 3)
B
Drop the voltage of EREF by 20 mV which was adjusted in 7.
to descend the stage to the direction of the sixth disc by 0.1 mm.
GND
EREF
When the mechanism unit is dislocated to the direction of
the sixth disc, turn VR302 clockwise. (Fig. 5)
C
VR302
Raise the voltage of EREF by 20 mV which was adjusted in 7.
to ascend the stage to the direction of the first disc by 0.1 mm.
12. Place the mechanism unit horizontally and recheck from 10.
13. After adjustment has been completed,
47kΩ
L.P.F.
14. Press the EJECT switch.
1µF
15. After the operation of the mechanism unit has stopped, turn off the power.
D
16. After the power has be turned off, turn on the power in one minute or more
and insert the magazine.
Oscilloscope
17. Check that the mechanism unit operates normally for the first and fourth discs.
18. Terminate all adjustment for OK (normal operation) and readjust for NG (abnormal operation).
E
F
72
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
A
B
Stopper bend of the
clamp lever.
NG
C
Dislocated toward the first DVD.
Fig. 3
5
6
R
E
Adjust the insertion gate of magazine to
the fourth scale.
Fig. 2
OK
D
Engaged in the center and pressed downward.
Fig. 4
E
NG
Dislocated toward the sixth DVD.
Fig. 5
F
XDV-M8357ZT/UC
5
6
7
8
73
1
2
3
4
6.5 TEST MODE
1) Precautions on Adjustment
• Because this equipment uses a single voltage (+5 V)
in the regulator, the reference voltage of a signal is
not GND, but is REFO (VR21, VR25, PREF). If REFO
and GND are mixed and touched at product
adjustment, correct potential cannot be measured
but also the servo malfunctions and an strong
shock applies to the pickup. So, note the following
items. REFO and GND must not be mixed on the
negative side of the probe of the measuring
apparatus. In particular, do not connect the
negative side of the ch1 probe of the oscilloscope to
REFO and the negative side of the ch2 probe to
GND. Further, in general, because most main units
of measuring apparatuses reach the same potential
as the negative side of the probe, make the main
unit of the measuring apparatus enter the floating
state. If REFO and GND are incorrectly connected,
immediately turn off the power.
• Be sure to turn off the power when attaching and
detaching the various filters and wire materials
required for measurement.
• For the adjustment and measurement after poweron, adjust or measure after having performed
running for about one minute until the circuit
becomes stable.
• Because various types of protection do not operate
by software in the test mode, do not apply a
mechanical and electrical shock during adjustment.
• This equipment uses a photo transistor to detect a
disc when inserting and removing it to and from the
tray. Accordingly, if strong light enters this
equipment with the case remove at repair and
adjustment, the following malfunctions may occur.
* Although there is a disc, play is disabled because
the disc cannot be used.
* A disc of 12 cm is incorrectly detected for a disc
of 8 cm.
When a malfunction occurred, take action such as
changing the position of the light source, changing
the orientation of this equipment or covering a
photo transistor.
• In the test mode, after having executed carriage
movement during focus search, immediately turn
off the power. (The lens is stuck up or down and
the actuator may be damaged by fire.)
• During disc replacement, press the key of the disc to
be replaced by a new one.
A
B
C
D
E
2) Test Mode
Because this machine is adjusted by combining a
pet unit, each adjustment key operation is also
performed by the pet unit. For reference purposes,
how to enter the test mode and key operation for
KEX-M9737ZT-02/UC are described. Besides, the key in this
adjustment text is also an KEX-M9737ZT-02/UC key.
• How to enter the test mode
Normal mode
Press the DISC key three times while
pressing the 1 key and 6 key.
Diagnosis mode
Press the AM and SEEK/TRACK DOWN key.
Test mode
• How to reset the test mode
Enter ACC and backup OFF.
• After having executed carriage movement during
focus search, immediately turn off the power.
(Because the lens is stuck, the actuator may be
damaged by fire.)
• The TR Jump below 255 TR continues operation
even if the key is detached. Other TR Jumps enter
the T Close state when the key is detached.
• As soon as the power is turned on/off, the Jump
Mode is reset to Single TR and the automatic
adjustment value returns to the initial value.
• During disc replacement, press the key of the disc to
be replaced by a new one.
• Be sure to load a DVD disc on the first tray of the
magazine.
F
74
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
Test mode operation flow
Normal
mode
Diagnosis
mode
Test mode IN
Key operation for FX-MG8606ZT/UC
Press the DISC key three times while
pressing the 1 key and 6 key.
Test contents execute : DISC key press
Test contents select : TRACK UP/DOWN
A
Test contents
1 key press
Command
Number
Press the AM and SEEK/TRACK DOWN key.
Test mode
DISC key press
Stage 0:System check mode
Bus-con
version display
00800000
Detailed error
code display
00810000
Power ON and
system check
00820000
2 key press
Oblique line : NC(Factory mode)
Bold line : Forgetting execution is noted
Power OFF
Clear all
memories
00840000
00830000
Sys-con,
mecha-con
test start
00860000
Debug mode
00850000
1
Stage 1:EDC measurement
EJECT
10030000
EDC mode
start
10690000
Play state
display
10040000
Try select
EDC mode 1
EDC mode 2
10700000
10710000
10211000
Auto adjustment
value display
10240000
Apply version
display
10000000
DVD error
rate check
10720000
EDC mode
end
10730000
EJECT
Servo. to
initial value
20060000
Play state
display
20040000
20030000
3
2
Stage 2:Disc type decision mode
Return to
stage1
20020000
B
Test
start
10940000
Disc type
decision
20070000
Try select
Auto adjustment
value display
20240000
20211000
Mech. test
mode
20400000
1
C
Stage 3: Focus close mode
Switch the
gain of OEIC
30330000
Auto adjustment
value display
30240000
Play state
display
30040000
Return to
stage 1
30020000
Return to
stage 2
30050000
S curve
mode IN
30090000
Carriage
outer move
30100000
Carriage
inner move
30110000
1
2
Tracking
close mode
40140000
TB auto
adjustment
40280000
Focus
close
30080000
LD ON
30130000
EQ measurement
mode
30220000
Stage 4:Tracking close mode
Return to
stage 1
40020000
Return to
stage 2
40050000
S curve
mode OFF
40130000
1
2
Disc type
discrimination
40160000
Auto adjustment
value display
40240000
Carriage
outer move
40100000
Carriage
inner move
40110000
D
Play state
display
40040000
Stage 5:Wave of servo condirmation mode
Track jump
(inner)
50180000
Track jump
(outer)
50190000
FT gain
adjustment
50260000
FB auto
adjustment
50270000
RF auto
adjustment
50250000
Tracking
open
50170000
Tracking
close
50140000
Carrige
inner move
50110000
Carrige
outer move
50100000
Tilt servo
move start
50350000
Tilt servo
move start
50360000
Focus
jump
50150000
CD error
rate check
50200000
Spindel
CAV move
50300000
Play state
display
50040000
Return to
stage 1
50020000
Return to
stage 2
50050000
1
2
Auto adjustment
value display
50240000
E
Stage 6:Mechamism test mode
Mechanism
test end
70450000
Motor negative
rotation
70440000
Motor positive
rotation
70430000
Operation
mode select
70420000
ELV/Try
select
70410000
3
F
XDV-M8357ZT/UC
5
6
7
8
75
1
2
3
4
Test Mode IN, Stage 0
- Outline
[Test Mode IN]
• [Test Mode IN] is a procedure for entering the DVD changer in the test mode.
• Once the DVD changer has exited from the test mode, restart the test mode from [Test Mode IN]
A
[Stage 0]
• This stage displays a version number of the bus microcomputer, checks the contents of detailed errors and
performs a system check.
- Operation Flow of [Test Mode IN] and [Stage 0]
!! To prevent a malfunction and damage !!
• When performing the test mode of [Stages 1 to 6], be sure to insert a DVD video disc in Tray 1
of the magazine. (If DISC1 is not a DVD video disc, the test mode does not function normally.
• When performing the test mode of [Stage 7], be sure to remove all the trays of the magazine and
use a magazine in which no tray is inserted. (If a tray is inserted in the magazine,
a mechanical unit may be damaged.
B
Test Mode
Start
Diagnostic
Mode
DVD Changer
Test Mode
While doubly pressing the [1] and [8] keys,
press the [DISC] key three times.
Test Mode IN
Doubly press the [AM] key and the
[SEEK/TRACK DOWN] key.
Stage 0 System Check Mode
C
Bus Microcomputer
Version Display
00800000
Detailed Error
Display
00810000
Power OFF
Power ON and
System Check
00820000
00830000
All Memory
Clear
00840000
Debug Mode
00850000
System Controller - MechanicalUnit Controller Test Start
00860000
Test Start
If [00800000] is executed when no disc is not inserted
in the magazine and the door opens, return value [00870000] is reached and
no more operation is enabled. At that time, turn off/on ACC once and restart
the test mode from [Test Mode IN] after having inserted the magazine.
10940000
To Stage 1
- Example of Test Execution
D
• Check a detailed error code.
1) Check the contents of an error
which is currently occurring.
2) Newly obtain error contents.
: Execute [00810000].
: Execute [00840000], [00830000], [00820000] and [00810000] in this order.
• Go to the next stage.
: Execute [00860000].
- Contents of Test
Command Test name
number
← Press the 2 key
Press the 1 key →
E
00800000 Bus microcomputer
version display
00810000 Detailed
error display
00820000 Power ON and
system check
00830000 Power OFF
00840000 All memory clear
00850000 Debug mode
00860000 System controller mechanical-unit
controller test start
Test contents
Execute test contents:
Press the DISC key.
Return to the command number
display: Re-press the DISC key.
Displays a bus microcomputer
version.
Displays a detailed error code.
Test contents selection item setting Return value
Selection switching: Pressing the
TRACK UP/DOWN key
Version number
OOO_XX (XX: error code)
For error contents, refer to the
error code table.
None
Turns on the power.
Turns off the power.
Clears error histories recorded in
the system microcomputer.
** Factory Mode **
Displays debug.
Moves to the test mode.
None
00800001
00800001
None
F
76
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
Stage 1
- Outline
[Stage 1] displays an application program version number and measures (DVD) an error rate.
- Operation Flow of [Stage 1]
Only the tray in which a
disc is inserted can be selected
for the [10211000] tray
selection.
After the [10030000] magazine has
been ejected, the test mode cannot be
continued.Turn off/on ACC once and restart
the test mode from [Test Mode IN].
From
Stage 2
Stage 3
Stage 4 and
Stage 5
Return to
Stage 1
X0020000
Stage 1 EDC Measurement Mode
Eject
10030000
Replayed Status
Display
10040000
EDC Mode
Start
10690000
Tray
Selection
10211000
EDC Mode 1
EDC Mode 2
10700000
10710000
Automatic Adjustment
Value Display
10240000
DVD Error Rate
Measurement
10720000
A
From Stage 0
System Controller - MechanicalUnit Controller Test Start
00860000
Application
Version Display
10000000
Test Start
10940000
EDC Mode
Termination
10730000
B
[10700000] and [10710000] are factory
verification modes. They are not used
usually. For incorrect execution,
terminate with [10790000].
∗∗ After execution of the [10690000] EDC
mode, be sure to execute [10730000] EDC mode
termination before executing [10211000] and
[10940000]. The test mode does not
function normally.
Disc Type
Decision
20070000
To Stage 1
- Example of Test Execution
• DVD error rate measurement:
Collectively execute [10690000], [10700000], [10720000] Measurement and [10730000] in this order (normally less than 0.1%).
For the details of the DVD error rate measurement method, refer to the appended table.
The CD error rate is enabled at [Stage 5].
• Display an automatic adjustment value of servo
Execute [10690000], [10240000] Display and [10730000] in this order. Only when [10690000] is executed, a normal value is displayed.
The initial value of automatic adjustment is displayed.
• Go to the next step: Execute [10940000].
- Contents of Test
C
Command Test name
number
Test contents
Test contents selection item setting Return value
10030000 EJECT
Ejects the magazine.
10040000 Replayed status
display
Displays a replayed status.
10211000 Tray selection
Clamps an optional disc
Execute test contents: Press the DISC key. Selection switching: Pressing the
Return to command number display:
TRACK UP/DOWN key
Re-press the DISC key.
Press the 1 key
↓
10240000 Automatic adjustment Displays an automatic adjustment
value display
result of a servo system.
10000000 Application version
display
10940000 Test start
Press the 2 key
10690000 EDC mode start
↓
10700000 EDC test mode 1
10710000 EDC test mode 2
10720000 Error rate
measurement
10730000 EDC mode end
Whether carriage returns the home
position or not is selected at ejection.
[10030000] With carriage home
00000000(With carriage home)
[10031000] Without carriage home 00000001(Without carriage home)
00000000(at servo OFF)
01010101(Servo initialization state)
02020202(at focus servo ON)
ID No.
(at DVD replay)
MSF No. (at CD replay)
A tray number is selected.
Executes [1021X000] "X" matching 0000000X("X" is a tray number.)
an optional tray number.
Toggle-selects an adjustment value
to be displayed. Display at selection
"0"[10240XXX]
Refer to the appended table.
"1"[10241XXX]
"2"[10242XXX]
Application program version number
Displays a version of an application
program.
Goes to Stage 2. (Starts the mechanical00000000
unit controller/microcomputer test mode.)
Starts normal replay after control data
TOC-RDX ("X" is a tray number.)
read for DVD, and after TOC read for CD.
Specifies a replay start position and A replay start position is set.(For DVD) EDC10000(for DVD)
performs solid replay.
ID number, and (for CD) MSF number. EDC1XXXX(for CD) and
Sets an MSF number after having X is a minute and second
executed 10711000.
Sets an ID number after having
10700000
executed 10700000.
** Factory Mode **
A replay start position is set
EDC10000(for DVD)
(For DVD) Starts the replay which
(For DVD) ID number,
EDC1XXXX(for CD) and
repeats the operation of 1-block
and (for CD) MSF number.
X is a minute and second
read/pause. (For CD) Starts the
Sets an MSF number after having
same operation as EDC mode 1
executed 10711000.
Sets an ID number after having
executed 10700000.
Measures a C1 error rate of DVD.
Selects between 1 and 64 of the
number of sampling blocks.
A C1 error rate is exponentially
(Usually 32 blocks)
displayed.
···Refer to the appended table.
Terminates the EDC mode.
None
XDV-M8357ZT/UC
5
D
6
7
8
E
F
77
1
2
3
4
Stage 2
- Outline
[Stage 2] sets and selects a disc type and test mode.
A
- Operation Flow of [Stage 2]
From
Stage 3,
Stage 4 and
Stage 5
Return to
Stage 2
Stage 2 Disc Type Decision Mode
Return to
Stage 1.
20020000
EJECT
20030000
Replayed
Status Display
20040000
∗∗ When executing [20400000] and
performing the mechanical-unit controller test
mode of [Stage 7], be sure to remove all the
trays from the magazine and use a magazine
in which no tray is inserted. (A mechanical
unit may be damaged.)
From Stage 1
Test Start
X0050000
10940000
Servo
Initialization
20060000
Disc Type
Decision
20070000
Only the tray in which a
disc is inserted can be selected
for the [10211000] tray
selection.
Tray
Selection
20211000
Automatic Adjustment
Value Display
20240000
From Stage 7
Mechanical-Unit
Controller Test End
70450000
Mechanical Unit
Test Mode
20400000
B
ELV/Tray
Selection
70410000
LD ON
Test Mode
10940000
30130000
To Stage 1
To Stage 3
To
∗∗ For the [20070000] Disk Type
~ [20070000] = [20211000] = [30130000] ~
When the test enters [Stage 2], be sure to execute [20070000].
If it is not executed, the test mode does not function normally.
A disc type selected for [20070000] must match that selected for [20211000].
Similarly, a type of an LD (laser diode) selected for [30130000] of [Stage 3] needs to
match a disc type selected for [20070000].(If it does not match,
the test mode does not function normally.)
After the [20030000] magazine has
been ejected, the test mode cannot be
continued.Turn off/on ACC once and restart
the test mode from [Test Mode IN].
- Example of Test Execution
Stage 7
• Go to [Stage 3]: Execute [20211000], [20211000] and [2006000] in this order.
• Go to [Stage 7]: Execute [20240000].
C
When the mechanical unit test mode is executed, the [20070000] Execution is unnecessary
because there is no disc in the magazine.
- Contents of Test
Command Test name
number
20020000 Return to Stage 1
20030000 EJECT
Test contents
Test contents selection item setting Return value
Execute test contents: Press the DISC key. Selection switching: Pressing the
Return to command number display: TRACK UP/DOWN key
Re-press the DISC key
Returns to Stage 1.
Ejects the magazine
00000000
Whether carriage returns to the home
position is selected at ejection.
[2003000] With home carriage
00000000 (With carriage home)
[2031000] Without carriage home 00000001 (Without carriage home)
20040000 Replayed Status
Displays a replayed status.
00000000 (at servo OFF)
Display
01010101(Servo initialization state)
02020202(at focus servo ON)
ID number (at DVD replay)
MSF number (at CD replay)
20060000 Servo Initialization Initializes a servo system.
Whether a servo system automatic
adjustment is performed or
not is selected at servo initialization.
[20610000] With offset adjustment
(Usually set to offset adjustment)
00000000(Irrespective of
[20060000] Without offset adjustment a selection result)
20070000 Disc Type Decision Decides a disc type to set a servo
A disc type is decided.
gain in accordance with the disc type [20070000] CD setting
00000000(at CD selection)
used for test.
[20071000] DVD1 layer setting
00000001(at DVD1 layer selection)
[20072000] DVD2 layer setting
00000002(at DVD2 layer selection)
[20073000] Reserved
00000003(Reserved)
20211000 Tray Selection
Clamps an optional disc
A tray number is selected.
Executes [2021X000] "X"
0000000X("X" is a tray number.)
↓
matching an optional tray number
Toggle-selects an adjustment value
to be displayed.Display at selection
20240000 Automatic
Toggle-selects an adjustment value
"0" [20240XXX]
Refer to the appended table.
Adjustment Value to be displayed.
"1" [20241XXX]
Display
"2" [20242XXX]
20400000 Mechanical-Unit
Moves to the mechanical-unit
00000000
Controller Test
controller test mode.
Mode
D
Press the 1 key
↓
Press the 2 key
E
F
78
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
Stage 3
- Outline
[Stage 3] is used for measuring a servo system. (LD ON to focal close)
- Operation Flow of [Stage 3]
LD which turns on for [30130000]
Select an LD (laser diode) which matches
a disc type selected for [Stage 2]
[20070000].
Stage 3 Focal Close Mode
Automatic Adjustment
Value Display
30240000
OEIC Gain
Switching
30330000
S Curve
Mode IN
30090000
A
From Stage 2
Carriage Move to
Outer Circumference
30100000
Replayed
Status Display
30040000
Return to
Stage 1
30020000
Return to
Stage 2
30050000
Servo
Initialization
20060000
Focal Close
LD ON
30080000
30130000
EQ Measurement
Mode
30220000
Carriage Move on
Inner Circumference
30110000
B
Test Start
[30100000] and [30110000] move
while the execution key (DISC key)
is being pressed.
- Example of Test Execution
Servo Start
10940000
20060000
TB Automatic
Adjustment
40280000
To Stage 1
To Stage 2
To Stage 4
∗∗ At [30220000] Execution, because the
pickup may be damaged, remove pickup
connector (CN101).Besides, because this mode
is a factory verification mode, it is
not used usually.
• S curve measurement:
Enter the [30130000] to [30090000] Measurement Mode.
→ [30080000] Measurement (An up and down movement is repeated at a fixed cycle in the S curve mode.)
→ Turn off the S curve mode for [40130000] of [Stage 4].
• Focus servo system measurement/Go to the next stage: Execute [30130000] and [300080000] in this order.
- Contents of Test
Command Test name
number
Press the 1 key
↓
Press the 2 key
Test contents
Test contents selection item setting Return value
Execute test contents:Press the DISC key.
Return to command number display:
Re-press the DISC key.
Selection switching:Pressing the
TRACK UP/DOWN key
30330000 OEIC gain switching ** Factory Mode **
Switch an OEIC gain.
A High/Low gain is selected.
[30331000] gain High
[30330000] gain Low
30240000 Automatic
adjustment value
display
An adjustment value to be
displayed is toggle-selected.
Display at selection
"0"[30240XXX]
"1"[30241XXX]
"2"[30242XXX]
Displays an automatic adjustment
result of a servo system.
30040000 Replayed status
display
Displays a replayed status.
30020000 Return to Stage 1
30050000 Return to Stage 2
30080000 Folcal close
Returns to Stage 1.
Returns to Stage 2.
Moves up and down the actuator
to the focus direction.
When a focal close condition is .
satisfied, turn on focal servo
Executes the ON/OFF of laser diode
(LD).
30130000 Turn on the LD
↓
30090000 S curve mode IN
30100000 Carriage move to
outer circumference
30110000 Carriage move to
inner circumference
30220000 EQ measurement
mode
C
00000000(for Low gain)
00000001(for Low gain)
Refer to the appended
table.
D
00000000(at Servo OFF)
01010101
(Servo initialization state)
02020202(at focus servo ON)
ID number (at DVD replay)
MSF number (at CD replay)
00000000
00000000
00000000
E
An LD to be turned on/off is
selected.
[30130000] DVD LD (650 mm)
[30131000] CD LD (780 mm)
Turn on/off the S curve confirmation mode.
Moves the carriage to the outer
circumference
Moves the carriage to the inner
circumference.
** Factory Mode **
Forcibly turn on the servo of focus
and tracking and check the
characteristics of servo ED.
00007801 (at CD LD ON)
00007800(at CD LD OFF)
00006501(at DVD LD OFF)
00006500(at DVD LD OFF)
00000000
32100000
32110000
00000000
F
XDV-M8357ZT/UC
5
6
7
8
79
1
2
3
4
Stage 4
- Outline
[Stage 4] is used for measuring a servo system. (Tracking close)
A
- Operation Flow of [Stage 4]
∗∗ Be sure to execute the [40800000] TB
(tracking balance) automatic adjustment.
[40140000] may not be able to be executed
normally.
Focus Close
30080000
Stage 4 Tracking Close Mode
Return to
Stage 1.
40020000
Return to
Stage 2.
40050000
B
[40100000] and [40110000] move
while the execution key (DISC key) is
being pressed. Both are valid
when the tracking servo is OFF
(opens).
From Stage 3
S Curve
Mode OFF
40130000
Tracking
Close
40140000
Carriage Move to
Outer Circumference
40100000
TB Automatic
Adjustment
40280000
Automatic Adjustment
Value Display
40240000
Disc Type
Confirmation
40160000
Test Start
10940000
Servo
Initialization
20060000
RF Automatic
Adjustment
50250000
Test Start
To Stage 2
To Stage 5
Carriage Move to
Inner Circumference
40110000
Replayed
Status Display
40040000
- Execution of Test Execution
• Tracking servo system measurement/Go to the next stage: Execute [40280000] and [40140000] in this order.
- Contents of Test
C
Command Test name
number
Press the 1 key
↓
Press the 2 key
D
E
↓
Test contents
Test contents selection item setting Return value
Execute test contents: Press the DISC key. Selection switching: Pressing the
Return to command number display:
TRACK UP/DOWN key
Re-press the DISC key.
40020000 Return to Stage 1 Returns to Stage 1.
40050000 Return to Stage 2 Returns to Stage 2.
40130000 S curve mode OFF Turns off the S curve confirmation
mode.
40140000 Tracking close
Turns on the tracking servo.
40280000 TB automatic
Automatically executes a tracking
adjustment
balance adjustment.
40100000 Carriage move to
Moves the carriage to the outer
outer circumference. circumference.
40110000 Carriage move to
Moves the carriage to the inner
inner circumference circumference.
40160000 Disc type
A disc type selected for
confirmation
[disc type (2007000)] can be
checked.
40240000 Automatic
adjustment value
display
Displays an automatic adjustment
result of a servo system.
40040000 Replayed status
display
Displays a replayed status.
00000000
00000000
00006500
00000000
00000000
42100000
42110000
Toggle-selects an adjustment
value to be displayed.
Display at selection
"0"[40240XXX]
"1"[40241XXX]
"2"[40242XXX]
00000000(at CD selection)
00000001
(at DVD1 layer selection)
00000002
(at DVD2 layer selection)
00000003(Reserved)
Refer to the appended table.
00000000(at servo OFF)
01010101
(Servo intitialization state)
02020202(at focus servo ON)
ID No.
(at DVD replay)
MSF No. (at CD replay)
F
80
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
Stage 5
- Outline
[Stage 5] is used for measuring a servo system.
A
- Operation Flow of [Stage 5]
∗∗ Be sure to execute [50250000], [50260000] and [50270000].
If they are not executed, a servo system is not stable,
and [50180000] and [50190000] may not be able to be executed normally.
The execution procedure is [5025] to [5027] to [5026] to [5025].
Execute [5025] once at the beginning and end respectively.
If less than 255 track jumps are executed in
the track jumps of [50180000] and [50190000],
the track jumps are repeated at regular intervals.
When they must be stopped, they can
be stopped with [50170000].
From Stage 4
Tracking
Close
40140000
Stage 5
Servo Waveform Confirmation Mode
Track Jump
(Inner Circumference)
50180000
Carriage Move To
Inner Circumference
50110000
Track Jump
(Outer Circumference)
50190000
Carriage Move to
Outer Circumference
50100000
Spindle CAV
Operation
50300000
FT Gain
Adjustment
50260000
Tilt Servo
Operation Start
50350000
FB Automatic
Adjustment
50270000
RF Automatic
Adjustment
50250000
Tilt Servo
Operation Stop
50360000
Automatic Adjustment
Value Display
50240000
Focus Jump
50150000
Replayed Status
Display
50040000
[50100000] and [50110000] move
while the execution key (DISC key) is
being pressed. Both are valid when
the tracking servo is OFF.
Tracking
Open
50170000
B
Tracking
Close
50140000
CD Error
Rate Measurement
50200000
Return to
Stage 1
50020000
Return to
Stage 2
50050000
Test Start
10940000
Servo
Initialization
20060000
To Stage 1
To Stage 2
C
D
- Example of Test Execution
• CD error rate measurement:
Execute [50250000]→[5027000]→[50260000]→[50250000] and [50200000] Measurement in this order.
• Tilt servo measurement:
Execute [50250000]→[5027000]→[50260000]→[50250000]→[50350000] Measurement and [50360000] in this order.
• Focus Jump measurement:
Execute [50250000]→[5027000]→[50260000]→[50250000] and [50150000] Measurement in this order.
• Track jump measureme:
Execute [50250000]→[5027000]→[50260000]→[50250000]→[50180000] or [50190000] Measurement in this order.
E
F
XDV-M8357ZT/UC
5
6
7
8
81
1
2
3
4
- Contents of Test
Command Test name
number
A
Test contents
Test contents selection item
setting
Return value
Execute test contents: Press the DISC key. Selection switching: Pressing the
Return to command number display:
TRACK UP/DOWN key
Re-press the DISC key.
50110000 Carriage move to
inner circumference
50100000 Carriage move to
outer circumference
50350000 Tilt servo operation
start
50360000 Tilt servo operation
stop
50150000 Focus jump
B
↓
Press the 1 key
50300000 Spindle CAV
operation
Press the 2 key
50040000 Replayed status
display
50020000 Return to Stage 1
50050000 Return to Stage 2
↓ 50180000 Track jump (Inner
circumference)
D
00000000
Turns off the liquid crystal tilt servo
00000000
Executes the focal jump of the a
DVD2 layer disc.(Swith the layer for
which focus is adjusted(between the
first and second layes)).
00000000(at Layer 0 after jump)
00000001(at Layer 1 after jump)
50200000 CD error rate
measurement
50240000 Automatic
adjustment value
display
C
Moves the carriage to the inner
circumference side.
Moves the carriage to the outer
circumference side.
Turns on the liquid crystal tilt servo.
50190000 Track jump
52110000
52100000
Measures a C1 error rate of CD. A sampling time of 1 to
(Usually five seconds)
30 seconds is set.
Once the execution key has been
pressed, the test enters the
52200000(during sampling)
number of sampling items setting
↓
mode with return value 51200100. A C1 error rate is exponentially
···Refer to theappended table.
displayed.
00000000
** Factory Mode **
Rotates a spindle at a constant speed
at 10 Hz for DVD.
Displays an automatic adjustment
Toggle-selects an adjustment
result of a servo system.
value to be displayed.
Display at selection
"0"[50240XXX]
"1"[50241XXX]
"2"[50242XXX]
Displays a replayed status.
Returns to Stage 1.
Returns to Stage 2.
Executes a track jump having the
specified number of tracks to the
outer circumference.
Executes a track jump having the
circumference.
The number of tracks to jump is
specified.
Refer to the appended table.
The number of tracks to jump is
specified. )
Refer to the appended table.
50260000 FT gain adjustment Executes focus and tracking gain
adjustments. (Automatic adjustment)
50270000 FB automatic
Exceutes a focus balance
adjustment
adjustment. (Automatic adjustment)
50250000 RF automatic
Executes an RF gain adjustment.
adjustment
(Automatic adjustment)
50170000 Tracking open
Turns off tracking servo.
50140000 Tracking close
Turns on tracking servo.
E
Refer to the appended table.
00000000(at servo OFF)
01010101(Servo intitialization state)
02020202(at focus servo ON)
ID number (at DVD replay)
MSF number (at CD replay)
00000000
00000000
The number of specified tracks
is displayed in hexadecimal
notation.
The number of specified tracks
is displayed in hexadecimal
notation.
00000000
00000000
00000000
00000000
00000000
F
82
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
Stage 6
A
- Outline
[Stage 6] is used for checking the ELV (elevation)/tray operation of a mechanical unit.
- Operation Flow of [Stage 6]
∗∗ When performing the trest mode
of [Stage 6], be sure to all the trays in the magazine
and usea magazine in which no tray is inserted.
(The mechanical unit may be damaged.)
[70440000]: (When driving ELV), operate
it in the direction of Tray 6.(Tray operation)
Operate the tray in the direction where it is
accommodated in the magazine.
From Stage 2
Mechanical-Unit
Controller Test Mode
20400000
Stage 6
Mechanical-Unit Controller Test Mode
Mechanical-Unit
Controller Test End
70450000
Motor backward
revolution
70440000
Mechanical-Unit
Controller Test Mode
20400000
Motor forward
revolution
70430000
Operation Mode
Selection
70420000
[70430000]: (When driving
ELV), operate it in the direction of Tray
6. (Tray operation) Operate the tray in the
direction where it is accommodated
in the magazine.
From Stage 2
B
ELV/Tray
Selection
70410000
If an amount of drive
is set to[Intermediate or Minor]
for [70420000], [70430000 (or 70440000)]
operates once at its execution each time
the execution key (DISC key) is pressed.
If an amount of drive is set to
[Major], it operates while
it is being pressed.
C
- Example of Test Execution
• Mechanical-unit controller test: Execute [70410000], [70420000] and [70430000 (or 70440000)] in this order.
- Contents of Test
Press the 2 key
Press the 1 key →
Command Test name
number
70450000 Mechanical-unit
controller test end
70440000 Motor backward
revolution
7043000 Motor forward
revolution
70420000 Operation mode selection
Test contents
Test contents selection item setting Return value
Execute test contents: Press the DISC key. Selection switching: Pressing the
Return to command number
TRACK UP/DOWN key
display:Re-press the DISC key.
D
Terminates the mechanical-unit
controller test mode.
Executes motor drive.
72440000
Executes motor drive.
72430000
Sets an amount of moror drive.
70410000 ELV/tray selection Selects a motor to be operated.
00000000
→
An amount of drive is switched.
(Switched to (Pressing the DISC
key) every execution)
[70420000]An amount drive is Minor.
[70410000]An amount fo drive is
Intermediate.
[70422000]An amount of drive is
Major.
Either the ELV motor or tray motor
is swithed.
(Switched to (Pressing the DISC
key) every execution)
[70410000]ELV motor selection
[70411000]Tray motor selection
00000000(at Minor amount
of drive)
00000001(at Intermediate
amount of drive)
00000002(at Major amount
of drive)
E
00000000(at ELV motor
selection)
00000001(at tray motor
selection)
F
XDV-M8357ZT/UC
5
6
7
8
83
1
2
3
4
TEST MODE APPENDED TABLE
- [X0240000]Return Value Table of Automatic Adjustment Values.
A
"0" [00654321]
"1" [00654321]
"2" [00654321]
B
For DVD
00h
E7h~1Fh
E7h~1Fh
1
1
07h~0Fh
7Bh~85h
-
65 : F offset adjustment value
43 : T offset adjustment value
21 : F. BAL adjustment value
65 : F. AGC adjustment value
43 : T. AGC adjustment value
2 : F. AGC status adjustment value
1 : T. AGC status adjustment value
65 : RF gain adjustment value
43 : Tilt servo adjustment value
21 : T. BAL adjustment value
For CD
00h
E7h~1Fh
E7h~1Fh
1
1
0Ah~12h
-
- DVD Error Rate Measurement Method
[Outline procedures] [10690000]→[10700000]→[10720000]Measurement→[10730000]
∗ It is recommended that DVD error rates be measured according to the following settings
1 [10690000] EDC mode start Starts replay.
2 [10700000] EDC mode 1
Moves the pickup to the position where an error rate is measured (an ID No. is specified).
Operation 1. Execute [10700000] (press the DISC key).→Return value: 11700100
Operation 2. Then, operate the [TRACK UP/DOWN key] and the [1] [2] keys,
display [11700601] or [117050F] and execute it (press the DISC key).
.... Points of the following ID Nos. are indicated respectively
601 = The sixth digit is 1 = 100000h.
50F = The fifth digit is F = F0000h.
.... (Application) If other ID Nos. must be specified, values can be set in the same manner as the following
number of track jumps setting method.
C
3 [10720000] Measurement
Sets the number of sampling items and measures an error rate.
Operation 1. Execute [10720000] (press the DISC key). Return value: 11720100
Operation 2. Then, operate the [TRACK UP/DOWN key] and the [1] and [2] keys,
sequentially display [11720203] and [11720102] and execute them (press the DISC key).
.... [11720(1)0(2)] Enter (1) and (2) in this order. Both [11720203] and [117200102] can be entered previously.
.... The number of sampling items is set according to Operation 2.
203 = The two digit is 3 = 30, 102 = The first digit is 2 = 2 and the result is "32" in total.
.... (Application) If other ID Nos. must be specified, values can be set in the same manner as the following number
of track jumps setting method.
- [50200000] CD Error Rate Measurement Method
∗ It is recommended that DVD error rates be measured according to the following settings.
[50200000] Measurement Sets a sampling time and measures an error rate.
Operation 1. Execute [50200000] (press the DISC key). Return value: 51200100
Operation 2. Then, operate the[TRACK UP/DOWN key] and the [1] and [2] keys,
display [51200105] and execute it (press the DISC key).
D
.... The sampling time is set to"five seconds" according to Operation 2.
105 = The first digit is 5 = 5 seconds
.... If other ID Nos. must be specified, values can be set in the same manner as the following number
of track jumps setting method.
- [50180000] or [50190000] Number of Track Jumps Measurement Method
E
[50180000] Jump
Sets the number of jumps and performs a track jump.
Operation 1. Execute [50180000] (press the DISC key). Return value: 51180100
Operation 2. Then, operate the [TRACK UP/DOWN key] and the [1]and [2] keys,
enter (1) and (2) of [51180(1)0(2)] and execute them (press the DISC key).
.... First enter (1) (the "number of digits" of a value set). Then enter (2) (the value of the number of
digitsset for (1)). The value of each digit can be corrected even any times until the execution key is
pressed. Example) [511810105] [511810205] [511810306] [511810103] Execute (Press the DISC key).
The 653 track jump is executed. (Before execution, the first digit is changed from 5 to 3.)
.... If a track jump of less than 255 is specified, the track jump is repeated at regular intervals until
tracking open [50170000].
F
84
XDV-M8357ZT/UC
1
2
3
4
5
6
SRAM access check error * 1
A0-A16 address line check error * 1
Program flash ROM read access check error * 1
GUI flash ROM read access check error * 1
MPEG decoder read access check error * 1
MY-CHIP access check error * 1
Track buffer access check error * 1
Track buffer address line check error * 1
CD-ROM error correction IC access check error * 1
Pull up/down check error * 1
Flash ROM ID code differs
→Flash ROM contents are damaged
System Controller Peripheral Check Error
System Controller Peripheral Check Error
System Controller Peripheral Check Error
System Controller Peripheral Check Error
System Controller Peripheral Check Error
System Controller Peripheral Check Error
System Controller Peripheral Check Error
System Controller Peripheral Check Error
System Controller Peripheral Check Error
System Controller Peripheral Check Error
Flash ROM Error
Flash ROM Error
Flash ROM Error
Flash ROM Error
Electricity
Electricity
Electricity
Electricity
Electricity
Electricity
Electricity
Electricity
Electricity
Electricity
Electricity
Electricity
Electricity
Electricity
12
13
14
7
flash ROM and system controller is disconnected
Flash ROM size differs
→Flash ROM contents are damaged.Wiring between
6
flash ROM and system controller is disconnected
Flash ROM silicone signature differs
→Flash ROM contents are damaged.Wiring between
Flash ROM ID code differs
→Flash ROM contents are damaged
Details and cause
Contents
Type
Error code
Diagnosis EMV onMajor
Detailed code
mode
screen display classification
01
02
03
04
05
06
07
08
09
0A
11
When the DVD cannot operate or if it stopped due to an error during operation, an error mode occurs and the cause of the error is displayed in numerals.
An object of this error No. display is to reduce the nonsense call of the user and aid in the analysis/repair in the service.
1) Summary of error display
* If major classification error codes are blank, no detailed error codes are not displayed in normal use. Check them for the detailed error codes of the test
mode.
- Error No. Display
5
7
8
A
B
C
D
E
F
XDV-M8357ZT/UC
8
85
86
Detailed
1
Electricity
Electricity
Electricity
Electricity
17
31
32
33
2
3
The DVD is stopping Error5
due to error detection
Check the X-th disc Error2
51
46
Check the X-th disc Error5
The DVD is stopping Error5
due to error detection
50
91
90
84
83
82
Electricity
Electricity
Mechanism
Mechanism
Mechanism
Electricity
→Wiring is disconnected and short-circuited on main unit.
Spindle Lock Error
Focus Search Error
Elevation Error
Tray Existence/Nonexistence
Error
Eject Error
Heat Error
Address Not Found
Focus is disabled
→Disc upside down, scratches, dirt and vibration
are strong
Because spindle lock is not done, subcode cannot be read
→Spindle is faulty and disc scratches, dirt and vibration
are strong.
MAG switch disconnection wait timeout
Elevation timeout at ejection
Tray withdrawal or insertion operation timeout
Tray is hooked at tray withdrawal
Timeout at elevation operation
Pickup section is excessively heated.
Mechanism controller error code F2 XXXX
→Wiring is disconnected and short-circuited on main unit.
CPU Peripheral Hardware Fault DMA address error is detected in flash ROM
→Wiring is disconnected and short-circuited on main unit.
CPU Peripheral Hardware Fault CPU address error occurs in flash ROM
CPU Peripheral Hardware Fault Slot invalid instruction occurs in flash ROM
→Wiring is disconnected and short-circuited on main unit.
→Wiring is disconnected and short-circuited on main unit
CPU Peripheral Hardware Fault General invalid interrupt occurs in flash ROM
CPU Peripheral Hardware Fault Undefined interrupt occurs in flash ROM
→Wiring is disconnected and short-circuited on main unit.
CPU Peripheral Hardware Fault CPU address error interrupt
→Wiring is disconnected and short-circuited on main unit
→Wiring is disconnected and short-circuited on main unit
CPU Peripheral Hardware Fault Slot invalid instruction interrupt occurs in ROM
CPU Peripheral Hardware Fault General invalid instruction occurs in ROM
→Wiring is disconnected or short-circuited on main unit
Write protection is not applied to flash ROM
→Flash ROM contents are damaged.Wiring between
flash ROM and system controller is disconnected.
No reset vector is written to the first address of flash ROM
→Flash ROM contents are damaged
Flash ROM checksum differs
→Flash ROM contents are damaged
Details and cause
CPU Peripheral Hardware Fault Undefined interrupt occurs in ROM
Flash ROM Error
Flash ROM Error
Flash ROM Error
Contents
3
46
The DVD is stopping Error5
due to error detection
81
45
Electricity
39
The DVD is stopping Error3
due to error detection
Electricity
38
47
Electricity
37
Mechanism
Electricity
36
D
The DVD is stopping Error2 or 5 80
due to error detection
Electricity
35
Electricity
Electricity
16
34
Electricity
Type
15
classification code
B
2
44
screen display
E
Error code
Major
C
mode
Diagnosis EMV on-
1
4
A
F
XDV-M8357ZT/UC
4
5
6
Electricity
Electricity
Electricity
Electricity
A3
A4
A5
A6
C0
C1
Check the X-th disc
7
Check the X-th disc
Check the X-th disc
Check the X-th disc
The DVD is stopping
due to error detection
46
46
46
47
Electricity
Electricity
Mechanism error code F8 0013
Subcode cannot be read
→Spindle is faulty and disc scratches, dirt and vibration
are strong.
Mechanism error code F8 0015
Mechanism error code F8 0016
Elevation positioning is disabled
→Power fault and control volume resistor is faulty.
FOK Error
ID/SUBCODE Error
Mechanism controller does not respond.
→Wiring is disconnected and short-circuited on main unit.
Mechanism controller
Communication Timeout
Target address could not be reached.
→Defective carriage/tracking and disc scratches
Disc data cannot be read
→Spindle is faulty and disc scratches, dirt and vibration
are strong.
DVD Read Error
Disc scratches
Video CD Read Error
Disc scratches
System Controller
Communication is disabled between system controller
Communication Error
and BUS microcomputer.
→Wiring between main unit and extension unit is
disconnected and short-circuited.
Low Temperature Detection Equipment temperature is lower than operable
... temperature.
CD-ROM Read Error
DVD Search Timeout Error
DVD disc having region code which cannot be played
back
Digital Copy Guard Error
DVD disc violated against digital copy guard
DVD File System Read Error DVD data read error
→Defective carriage/tracking and disc scratches
Region Code Error
Communication Error between No communication is done from BUS microcomputer.
BUS Microcomputer
→Wiring between main unit and extension unit is
and System Controller
disconnected and short-circuited.
Unexpected Error in Mechanism
Controller Communication
Mechanism error code FA XXXX
Communication is disabled between mechanism
controller and system controller.
→Wiring is disconnected and short-circuited on main unit.
TOC Error
Mechanism controller
Communication Error
Mechanism Unit Reference
Voltage Error
Spindle Low Revolution Error
Spindle High Revolution Error
Movement is disabled to inner circumference and
movement is disabled from inner circumference
→Home SW is faulty and carriage movement is faulty
Details and cause
Carriage Home Error
Contents
6
Electricity
Electricity
A1
A2
Check the X-th disc
Check the X-th disc
Electricity
B3
Electricity
Electricity
B2
A0
Electricity
B1
Region code error Error09
Electricity
Electricity
Mechanism
Mechanism
Electricity
Electricity
98
B0
95
96
97
Check the X-th disc Error2
Check the X-th disc Error2
The DVD is stopping Error6
46
46
due to error detection
93
94
Check the X-th disc Error2
Check the X-th disc Error2
46
46
Error code
Diagnosis EMV onMajor
Detailed Type
mode
screen display
classification code
44
Check the X-th disc Error2
92
Electricity
5
7
8
A
XDV-M8357ZT/UC
8
B
C
D
E
F
87
E
Detailed
classification code
88
1
C6
C7
The DVD is stopping Error-06
due to error detection
The DVD is stopping Error-06
due to error detection
Electricity
Electricity
Electricity
D
Power Supply Fault
Power Supply Fault
Power Supply Fault
Power Supply Fault
Contents
Higher or lower than specified voltage, otherwise no
power is issued.
→Defective switching transistor and power supply fault
Higher or lower than specified voltage in 2.5 V-system
power supply, otherwise no power is issued.
→Defective switching transistor and power supply fault
Higher or lower than specified voltage in 3.3 V-system
power supply, otherwise no power is issued.
→Defective switching transistor and power supply fault
Higher or lower than specified voltage in 9 V-system
power supply, otherwise no power is issued.
→Defective switching transistor and power supply fault
Details and cause
2
3
R :
F
:
.
.
V :
S :
A V
/
1 = '
/
'
L
S H :
F
XDV-M8357ZT/UC
4
A V :
.
.
R E G :
F
← (20)AV1 chip revision
← (16)Flash ROM version 2 and system controller version
← V:(15)Flash ROM version R and (13)region code
Y ← (12)Destination setting and (13)region code of player
← (10)AV1 chip version and (11)Flash ROM size
← (8)Output video format
← (5)Error history
← (2)Receiving code
3
(14)DVD error rates → E R (17)System microcomputer disc judgment → M M (18)Mechanism microcomputer disc judgment → D S C (19)Disc type in a magazine →
V -
O E :
M C T -
E :
S T A T S -
N O W -
T G T -
2
(1)Address →
(3)Target operating state →
(6)Current operating state →
(7)Current state →
(9)Command history to →
mechanism microcomputer
An object of this debug mode is to aid in the analysis/repair in the service by displaying the version display, error rate and error history of the
microcomputer when this equipment was stopped due to a fault.
• How to enter the debug mode
Follow the procedures below.
1. Enter the test mode.
2. Set the normal mode debug screen (00850000).
3. Set AccON to OFF.
4. Continue pressing the EJECT key for five seconds with the door closed.
5. Set AccOFF to ON without releasing the EJECT key as is.
• Debug mode reset
Acc OFF.
• Screen configuration
- Debug Mode
Because door opens, this equipment mechanism stops
The lid of the DVD Error-01
Mechanism Door Opens.
is opening
No disc is loaded
Mechanism Empty Magazine Insertion There is no disc.
* 1: This code is detected only when the system controller peripheral test was executed in the test mode.
C5
The DVD is stopping Error-06
due to error detection
Electricity
Type
C
C4
Error code
Major
B
The DVD is stopping Error-06
due to error detection
Diagnosis EMV onmode
screen display
1
4
A
5
6
7
8
- Explanation of Display Contents by Item
(1) Address display
This item displays the address which is being traced currently.
DVD
******* ID display (8 hexadecimal digits)
CD/VCD
0000**** A-TIME (minutes and seconds)
CD
00000000 Fixed
A
(2) Receiving code
R: ** ** **
This item displays the command transferred from the BUS microcomputer to the system controller.
(3) Target operating state
TGT: * **
This item displays the number of the tray to which playback operation is being attempted and the
internal state of the player.
Number of tray
Internal state of player
1-6
01
02
03
04
05
06
07
08
(4) Error number
This item displays the current error number.
B
Disc changing
Waiting for power-off
Stopping
Disc being detected
During setup
TOC being read
During playback
Searching
E : ** **
(5) Error history
OE : ** ** ** **
This item displays the past error history.
** ** ** **
The upper left is the latest error number. The same number as the current error number is displayed in an error state.
This error history is stored in flash ROM and will not be cleared even for backup OFF.
C
(6) Current operating state
NOW : * **
This item displays the number of the current tray and the internal state of the player.
Number of tray
1-6
Internal state of player
01
Disc changing
02
Waiting for power-off
03
Stopping
04
Disc being detected
05
During setup
06
TOC being read
07
During playback
08
Searching
(7) Status display
This item displays the internal state of the current player.
STATS- **
00
01
02
03
04
05
06
81
82
83
84
85
86
TOC:
TOC information read step information.
(8) Output video formats
NTSC (National Television System Committee) method
PAL (Programmable Array Logic) method
Automatic setting
D
No tray is selected.
Tray 1 is selected.
Tray 2 is selected.
Tray 3 is selected.
Tray 4 is selected.
Tray 5 is selected.
Tray 6 is selected.
Tray 1 disc is changing.
Tray 2 disc is changing.
Tray 3 disc is changing.
Tray 4 disc is changing.
Tray 5 disc is changing.
Tray 6 disc is changing.
E
V-****
[NTSC]
[PAL]
[AUTO]
F
XDV-M8357ZT/UC
5
6
7
8
89
1
2
3
(9) Command history to mechanical-unit microcomputer
This item displays past commands from
left to right and from up to down.
Commands
A
MCT : ** ** ** **
** ** ** **
01
02
03
04
05
06
07
08
09
0A
0B
0C
B
Communication Start
Stop
Seek
Read
Pause
Fast Forward
Reverse
Disc Replacement
Get Address
Get Power Startup State
Get Disc Information
Get Final Mechanism Controller
Error Status
Communication Reset
Test Mode ON
Get Control Data
Get TOC Information (CD Only)
Get Magazine Information
Get CD Address
EJECT
Power-Off Processing
EJECT Interrupt
0D
0E
10
11
12
14
15
16
17
C
4
(10) AV1 chip revision
This item displays a revision of the AV1 chip.
AV1 = '*'
(11) Flash ROM size
This item displays a size of flash ROM.
FLSH : *
(12) Destination setting
F : *** / *
(13) Region setting
REG : *Y
R:*
This item displays the region setting of the player.
(14) Error rate display
ER- **** ****
Error rates are displayed for DVD (displayed only for DVD).
C1 error rate for disc playback is displayed.
To ensure calculation accuracy, the number of errors is being counted in a unit of 16 blocks.
(C1 1block) = (182bytes x 208line = 37856bytes)
(C1 16block) = (182bytes x 208line = 16block = 605696bytes)
The minimum resolution is set to 1.65099E-6 .
Usually, an error rate is less than 1.0E-3 .
D
(15) Flash ROM version 1
Version of the high-level module in flash ROM.
Flash ROM version.
V : *. *** *
**
(16) Flash ROM version 2 and system controller version display
These items display a version of a low-level module
S : *. **
in flash ROM.
The version of the ROM incorporated in the system controller. *. ***
E
F
90
XDV-M8357ZT/UC
1
2
3
4
5
6
(17) Disc judgment(System microcomputer)
7
8
MM : ***
non
DSC
NG
CD
CDP
CDC
D
DVD
DNG
DOK
CDA
CDR
VC1
VC2
Disc not decided
No disc
Disc of type not fixed
No match etc.
CD (format not decided)
CD partial disc
CD combined disc
DVD (format not decided)
DVD (Region not decided)
DVD (Disc which cannot be played back due to a region error)
For DVD
For CD-DA
For CD-ROM
For VCD(Ver1.1)
For VCD(Ver2.0)
A
B
(18) Disc judgment(Mechanism microcomputer)
DSC : ***
This item displays the type of the disc which is being clamped.
NON
DVD
CD
VCD
(19) Disc type in a magazine
No disc
For DVD
For CD
For VCD
For six sheets
The display format is the same as the system microcomputer decision results of item 17.
(20) AV1 chip version
AV1:*.***
C
Function description
Clear error histories by pressing the upper left section of the screen ten consecutive times.
D
E
F
XDV-M8357ZT/UC
5
6
7
8
91
1
2
3
4
7. GENERAL INFORMATION
7.1 DIAGNOSIS
A
7.1.1 DISASSEMBLY
Note:
When disassembling a product, be sure to set the PU unit short circuit switch to the short circuit direction.
The vertical and horizontal specifications of a product are switched by switching the spring hooking position using
an arm. At normal assembly and disassembly, the arm switches the position at the position which conforms to the
horizontal specifications. However, because this product conforms to the vertical specifications, take notice not to
forget the changeover.
The changeover position and method are as follows:
Because a changeover arm is provided in the hole near by the center of the product left and right sides, use the
arm to switch the position. For the confirmation of the position, because H and V are marked on the top case.
Accordingly, to assemble a product, adjust H and V conforming to the installation specifications of the product.
B
- Removing the Upper Case (Fig.1)
1
Remove the screw.
2
Remove the eight screws and then
remove the Upper Case.
2
2
1
C
2
2
2
2
2
2
Upper Case
D
Fig.1
- Removing the DVD/CD Mechanism Unit (Fig.2)
DVD/CD Mechanism Unit
1
Remove the four dampers.
2
remove the two springs.
1
1
Disconnect the connector and then remove the
DVD/CD Mechanism Unit.
E
2
- Removing the Grille Assy (Fig.2)
3
Remove the two screws.
2
1
1
3
3
Disconnect the connector and then remove
the Grille Assy.
Grille Assy
Fig.2
F
92
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
- Removing the Rear Frame Unit (Fig.3)
2
A
1
Remove the two screws.
2
Pull out the Rear Frame Unit in the arrow
indicated direction.
1
1
Rear Frame Unit
- Removing the Extension Unit (Fig.4)
1
2
Fig.3
Shield
Remove the two screws and then remove
the Shield.
3
3
3
3
2
Remove the screw.
1
1
3
B
Remove the four screws.
Extension Unit
Disconnect the connector and then remove the
Extension Unit.
C
Fig.4
- Removing the MF Unit (Fig.5)
1
Remove the three screws and then remove
the MF Unit.
1
1
MF Unit
D
1
Fig.5
E
F
XDV-M8357ZT/UC
5
6
7
8
93
1
2
3
4
Precautions when making servicing works
1) Since the upper surface of the arrowed magazine slot
in the DVD/CD mechanism unit can be deformed
comparatively easily, do not hold this section when
making servicing work. (Refer to Fig. 6)
A
DVD/CD Mechanism Unit
2) The stage mechanism projects downward beyond the
low end of the chassis when it is reset.
Consequently, the stage mechanism may be damaged
to cause functional failures when handled carelessly.
When placing the mechanism, pay great attention not
to damage the gear and the pickup unit.
B
C
Fig. 6
- Removing the pickup unit(Fig. 7)
- Removing the PCB unit(B)(Fig. 7)
1. Set the short switch of the pickup unit to the SHORT
side.
2. Remove the flexible PCB from the connector.
3. Unscrew one screw A to remove the grease cover.
4. Unscrew one screw B to remove the plate spring A.
5. Unscrew one screw C to remove the plate spring B.
6. Remove the pickup unit together with the main shaft.
7. Remove the cushion from one side only to pull out
the main shaft. AT this time, pay attention not to lose
the removed cushion.
Short Switch
1. Remove soldering from the linear position sensor
(VR301).
2. Unscrew the two screws D to remove the PCB unit(B).
- Precautions when installing the linear position
sensor(Fig. 7)
1. If the linear position sensor (VR301) is not being
properly inserted into the U-groove provided in the
detection lever, elevation movement failures can
occur.
When installing the linear position sensor to the
DVD/CD mechanism unit, be sure to insert it into the
U-groove provided in the detection lever securely.
Cushion
C
D
Plate
Spring B
Main Shaft
Cushion
Pickup Unit
B
Plate
Spring A
A
PCB
Unit(B)
D
Grease
Cover
Soldering
D
E
VR301
Fig. 7
F
U-groove
94
Detection Lever
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
7.1.2 CONNECTOR FUNCTION DESCRIPTION
A
Notes
CD-Rs may not
be playable in
this compact
disc player.
B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1. +B
2. NTSO
3. SG
4. SGND
5. CDL+
6. CDR+
7. NC
8. TXM+
9. NC
10. ACC
11. GND
12. NC
13. NC
14. NC
15. CDL16. CDR17. SGND
18. TXM19. NC
20. MUTE
C
D
E
F
XDV-M8357ZT/UC
5
6
7
8
95
1
2
3
4
7.2 IC
LC89170MP
PD4995A
TC7SET04FUS1
M5M51008DKV-70HI
PD6531A
PD6520A
MAX662AESA
MC33202D
MSM5117800F-60JS
TC7SET08FUS1
TC7SH08FUS1
TC9461F
TC7SH32FUS1
PEG114A
A
VCC
OUT2
IN2
IN2
8
7
6
5
VCC 1
28 VSS
DQ1 2
27 DQ8
DQ2 3
26 DQ7
DQ3 4
25 DQ6
DQ4 5
24 DQ5
we 6
+
C
ras
+
NC
A10R
1
2
3
4
OUT1
IN1
IN1
VEE
A0
D
TC74VHCT08AFTS1
TC74LCX245FTS1
LC89513KP
PE5272A
LC35256FT-70U
*MSM5117800F-60JS
MC33202D
B
PD3411A
TC74VHC00FTS1
TC74VHC139FT
CY2292SI-1A0
MSM56V16160DP-10TS
MB86373BPFV-G-BI
TC74VHC541FTS1
23 cas
A0~A9,A10R
7 ras
cas
8 DQ1~DQ8
oe
we
9
VCC
VSS
10
NC
:Address input
:Row address strobe
:Column address strobe
:Data input/output
:Output enable
:Write enable
:Power supply
:GND
:Not used
22 oe
21 A9
20 A8
19 A7
A1 11
18 A6
A2 12
17 A5
A3 13
16 A4
15 VSS
VCC 14
*TC7SET08FUS1
*TC7SH08FUS1
1 IN B
5 VCC
E
IC's marked by * are MOS type.
Be careful in handling them because they are very
liable to be damaged by electrostatic induction.
2 IN A
3 GND
4 OUT Y
F
96
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
- Pin Functions (TC9461F)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59-62
Pin Name
VSS
BCK
AOUT
DOUT
MBOV
IPF
SBOK
CLCK
VDD
VSS
DATA
SFSY
SBSY
SPCK
SPDA
COFS
MONIT
VDD
TESIO0
P2VREF
SPDO
PDOS
PDO
TMAXS
TMAX
LPFN
LPFO
PVREF
VCOREF
VCOF
AVSS
SLCO
RFI
AVDD
RFCT
RFZI
RFRP
FEI
SBAD
TSIN
TEI
TEZI
FOO
TRO
VREF
RFGC
TEBC
FMO
FVO
DMO
2VREF
SEL
FLGA
FLGB
FLGC
FLGD
VDD
VSS
IO0-3
I/O
O
O
O
O
O
O
I/O
O
O
O
O
O
O
O
I
O
O
O
O
O
I
O
I
O
O
I
I
I
I
I
I
I
I
I
O
O
O
O
O
O
O
O
O
O
O
O
I/O
Function and Operation
GND
Bit clock (1.4122MHz) output
Audio data output terminal
Digital out output terminal
Buffer memory over signal output terminal
Augment flag output terminal
CRCC decision result output terminal of subcode Q data
Clock output/input terminal for subcode P-W data reading
Positive power supply terminal
GND
Subcode P-W data output terminal
Play group frame synchronous signal output terminal
Subcode block synchronous output signal
Clock output terminal for processor status signal reading
Processor status signal output terminal
Correct group frame clock (7.35 kHz) output terminal
LSI internal signal monitor terminal
Positive power supply terminal
Test input/output terminal
2VREF terminal for PLL group only
VCO center frequency shift terminal
Phase error signal output terminal of EFM signal and PLCK signal
Phase error signal output terminal of EFM signal and PLCK signal
TMAX detection result output terminal
TMAX detection result output terminal
Inverted input terminal of low-pass filter amplifier
Output terminal of low-pass filter amplifier
VREF terminal for PLL group only
VCO center frequency reference level terminal
Filter terminal for VCO
Analog group ground
Output terminal for data slice level generator DAC
RF signal input terminal
Analog group power supply terminal
RFRP signal center level input terminal
Input terminal for RFRP zero cross
RF ripple signal input terminal
Focus error signal input terminal
Sub beam summing signal input terminal
Test input terminal
Tracking error input terminal
Input terminal for tracking error zero cross
Focus equalizer output terminal
Tracking equalizer output terminal
Analog reference power supply terminal
RF amplitude adjustment control signal output terminal
Tracking balance control signal output terminal
Feed equalizer output terminal
Speed error or Feed search EQ output terminal
Disk equalizer output terminal
Analog reference power supply terminal
APC circuit ON/OFF signal output terminal
External flag output terminal for internal signal monitor
External flag output terminal for internal signal monitor
External flag output terminal for internal signal monitor
External flag output terminal for internal signal monitor
Digital power supply terminal
Digital GND
General purpose I/O port
A
B
C
D
E
F
XDV-M8357ZT/UC
5
6
7
8
97
1
Pin No.
63
2
Pin Name
dmout
I/O
I
ckse
dact
TESIN
TESIO1
VSS
PXI
PXO
VDD
XVSS
XI
XO
XVDD
DVDD
RO
DVSS
DVR
LO
DVDD
TEST1-3
BUS0-3
VDD
VSS
BUCK
cce
TEST4
tsmod
rst
TEST0
hso
uhso
I
I
I
I
B
C
EMPH
LRCK
O
O
4
Function and Operation
A terminal for setting the mode to output binary PWM for a feed equalizer
from I/O terminals 0 and 1, and binary PWM for disc equalizer from I/O
terminal 2 and 3
X'tal select terminal
Test terminal
Test input terminal
Test input/output terminal
Digital GND
DSP group clock oscillation circuit input terminal
DSP group clock oscillation circuit input terminal
Digital power supply terminal
Ground terminal for system clock oscillation circuit
System clock oscillation circuit input terminal
System clock oscillation circuit output terminal
Power supply terminal for system clock oscillation circuit
D/A converter power supply terminal
R channel data positive rotation output terminal
D/A converter analog ground terminal
D/A converter reference voltage terminal
L channel data positive rotation output terminal
D/A converter power supply terminal
Test terminal
Data input/output terminal for microcomputer interface
Digital power supply terminal
Digital GND
Clock input terminal for microcomputer interface
Chip enable signal input terminal for microcomputer interface
Test terminal
Local test mode select terminal
Reset signal input terminal
Test terminal
Play speed mode flag output terminal
uhso hso
Play speed
H
H
Once speed play
H
L
Twice speed play
L
H
Four times speed play
L
L
Eight times speed play
A
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82-84
85-88
89
90
91
92
93
94
95
96
97
98
3
I
O
I
O
O
O
I
I/O
I
I
I
I
I
I
O
O
D
99
100
Emphasis flag output terminal of subcode Q data
Channel clock (44.1 kHz) output terminal
*TC9461F
26
50
*TC7SH32FUS1
25
51
1 IN B
5 VCC
E
2 IN A
1
3 GND
4 OUT Y
76
100
75
F
98
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
- Pin Functions (PEG114A)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29, 30
31
32
33
34
35
36
37
38
39
40
41
42, 43
44
45
46
47
48
49
50
51-54
55
56
57
58-61
62
63
64
65-72
73
74
75
Pin Name
RFSCD
RFSCB
LCDBIAS
LCDTLT
LDCONT
PSC
FG
BYTE
CNVSS
DSCSIZ
VMCONT
XMRES
XOUT
VSS
XIN
VCC
NC
XMAG
NC
XIRQ
OEIC
FEB
FLGA
FLGB
FLGC
LCDCLK
FLGD
TXCLK
NC
EEPDO
EEPDI
EEPSK
EEPCS
TEST_TX
TEST_RX
HSO
UHSO
XREADY
ASTB
XHOLD
NC
XRD
NC
XWR
NC
LCDRS
XCS
CD/DVD
LCDDT3-0
LCDEN
XCCE
BUCK
BUS3-0
VCC
NC
VSS
AD7-0
TXDQSY
BSENS
SRSENS
I/O
O
Format
C
O
O
I
I
C
C
O
O
I
O
C
C
I
I
I
O
C
I
I
I
I
O
I
O
O
O
I
I
I
I
O
I
C
C
C
C
C
O
C
O
C
O
O
O
O
O
O
O
I/O
C
C
C
C
C
C
C
C
I/O
I
I
I
C
Function and Operation
TA1254AF serial data
TA1254AF bit clock
Liquid crystal temperature augment output
Liquid crystal tilt augmenter control output
LD ON/OFF control output
VRCK deviding ON/OFF
FG pulse input
Connect to VCC
Connect to VSS
8cm/12cm select
9V regulator output voltage control output
Reset input
Main clock oscillation terminal
GND
Main clock oscillation terminal
Power supply terminal
Not used
Magazine detection switch input
Not used
Interruption input
OEIC gain select output
FE balance control output
TC9461 internal signal monitor input
TC9461 internal signal monitor input
TC9461 internal signal monitor input
Liquid tilt driver clock output
TC9461 internal signal monitor input
CD-TEXT clock output
Not used
EEPROM data output
EEPROM data input
EEPROM clock output
EEPROM chip select
RS232C communication data output
RS232C communication data input
Play speed mode flag
Play speed mode flag
Wait signal input
Address latch output
Hold signal input
Not used
Read signal output
Not used
Write signal input
Not used
LCD register select
Chip select signal output
CD/DVD select output
LCD display data
LCD enable
Servo processor i/f
Servo processor i/f
Servo processor i/f
Power supply terminal
Not used
GND
Address/data input/output
CD-TEXT sub-code synchronous input
Backup sense input
DDC sense input
A
B
C
D
E
F
XDV-M8357ZT/UC
5
6
7
8
99
1
Pin No.
76
77
78
79
80
81
82
83
84
85
86
87
88
89,90
91
92
93
94
95
96
97
98
99
100
A
B
C
2
Pin Name
OPEN
SEEKT
I13
I2
I4
HOME
VDCONT
SPCONT
DCONT
XSYSRST
ADENA
DSP
XTESTIN
KEYIN2,1
VDSENS
DISK
ELVPVO
ELVREF
TRP
AVSS
TEMP
VREF
AVCC
RFSLC
I/O
Format
O
O
O
O
I
O
O
O
O
O
I
I
C
C
C
C
3
Function and Operation
Open
SEEK time monitor output
Motor driver control output
Motor driver control output
Motor driver control output
Home position detection output
VD control output
Spindle control output
Driver power ON output
Reset output
Reference voltage supply output for A/D
Disk detection timing input
Unit check start input
Key sense
VD short detection input
Disk/No disk sense, 8/12cm detection
Slide voltage input for ELV detection
ELV reference voltage input
Tray position input
Analog ground
Temperature detection input
Reference voltage input
Analog power supply
TA1254AF data latch
C
C
C
C
I
I
I
I
I
I
O
C
*PEG114A
Format
C
Meaning
C MOS
1
30
4
100
31
*LC89170MP
D
81
80
51
50
E
F
100
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
- Pin Functions (PD4995A)
Pin No.
1,2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22-25
26
27
28-31
32
33
34
35
36-38
39-41
42
43
44-50
51,52
53
54
55
56
57-60
61
62
63-66
67
68
69
70
71
72
73
74
75
76
77
78
79
80-91
92-95
96
97
98-101
Pin Name
GND
NC
DXTLI
I/O
DXTLO
BUNRI
TSTSTB
PC2/STB
PC3/BSYNC
PC4/SELNED
PA7/NED7
PA6/NED6
PA5/NED5
PA4/NED4
VDD
GND
PA3/NED3
PA2/NED2
PA1/NED1
PA0/NED0
BMODE1
DD7-4
GND
VDD
DD3-0
XDCAS
XDWE
XDOE
XDRAS
DA12-10
DA9-7
GND
VDD
DA6-0
GND
VDD
XWR
XSACK
SREQ
SDATA0-3
GND
VDD
SDATA4-7
XAVTRM
O
I
I
I/O
I/O
I
I/O
I/O
I/O
I/O
BMODE2
DMACKI
GND
DMACKO
XSCL1
XSWAIT
XSRD
XSWR
XSDREQ
SDACK
VDD
GND
SA11-0
SAD7-4
VDD
GND
SAD3-0
I
I/O
I/O
I/O
I/O
I
I/O
I/O
O
O
O
O
O
O
O
O
O
I
O
O
O
I
I
O
I
O
I
I
O
I
I
I/O
I/O
Function and Operation
Digital circuit GND
Not used
27MHz crystal connection terminal which oscillates reference clock signals of
the spindle and PLL
Not used
Separation test control terminal for internal RAM
Test mode setting input
Not used
Not used
I/O setting terminals for NED (7:0), STM and BSYNC terminals
Not used
Not used
Not used
Not used
Digital circuit power supply
Digital circuit GND
Not used
Not used
Not used
Not used
Sets which test is done in the test mode
DRAM data bus for VBR buffer
Digital circuit GND
Digital circuit power supply
DRAM data bus for VBR buffer
DRAM CAS signal for VBR buffer
DRAM WE signal for VBR buffer
DRAM OE signal for VBR buffer
DRAM RAS signal for VBR buffer
Not used
DRAM address signal for VBR buffer
Digital circuit GND
Digital circuit power supply
DRAM address signal for VBR buffer
Digital circuit GND
Digital circuit power supply
Not used
Transfer response terminal for VIDEO_DMA channel
Data transfer request terminal for VIDEO_DMA channel
Data output bus for VIDEO=DMA channel
Digital circuit GND
Digital circuit power supply
Data output bus for VIDEO=DMA channel
Signal indicating the head of the sector of the transfer data for VIDEO_DMA
channel
Sets which test is done in the test mode
System clock input of DVD/CD ROM data
Digital circuit GND
Outputs reference crystal clock signals of the spindle and PLL
Chip select signal from the main CPU
WAIT output to the main CPU
RD signal for the main CPU
WR signal for the main CPU
DMA request for the main CPU
DMA response signal
Digital circuit power supply
Digital circuit GND
Main CPU address
Main CPU data bus
Digital circuit power supply
Digital circuit GND
Main CPU data bus
XDV-M8357ZT/UC
5
6
7
8
A
B
C
D
E
F
101
1
Pin No.
102,103
104
105,106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
A
B
Pin Name
XIRQ10,11
VDD
GND
CKCD
DIFOUT
BCK
LRCK
ADATAO
CDDT
CDLR
CDBCK
CDDO
C2FI
WFCK
SCOR
SBSO
EXCK
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
C
2
VDD
GND
DSPA0
DSPA1
DSPA2
ASDATA0/PB0
ASDATA1/PB1
ASDATA2/PB2
ASDATA3/PB3
VDD
GND
ASDATA4/PB4
ASDATA5/PB5
ASDATA6/PB6
ASDATA7/PB7
XAWR
ASREQ
TMC2
ASTB
I/O
O
I
O
O
O
O
I
I
I
I
I
I
I
I
O
O
O
O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
I
I
I
D
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155,156
157
158
159
160
161
162
163
E
F
102
XMCS
XIRQ2
XMWR
XMRD
MAD7/PE7
MAD6/PE6
MAD5/PE5
MAD4/SA16/PE4
GND
VDD
MAD3/SA15/PE3
MAD2/SA14/PE2
MAD1/SA13/PE1
MAD0/SA12/PE0
RPWM
GND
VDD
RERR
FPWM
VPWM
PPWM
FGPL
XASACK
I
O
I
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
O
O
O
O
I
O
3
4
Function and Operation
Interrupt request for the main CPU
Digital circuit power supply
Digital circuit GND
Master clock of audio I/F block
Digital audio output
Bit clock output to DAC
LRCK signal output to DAC
Serial data output to DAC
Audio data input from CD decoder
LRCK signal input from CD decoder
Bit clock input from CD decoder
Digital out signal input from CD decoder
Input terminal for the C2 error flag from CD decoder
CD frame clock signal
CD subcode sync input terminal
CD subcode data input terminal
Shift clock which generates the timing at which data is sent to the SBSO
terminal
Digital circuit power supply
Digital circuit GND
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Digital circuit power supply
Digital circuit GND
Not used
Not used
Not used
Not used
Not used
Transfer request terminal for AUDIO_DMA channel
Terminal test control terminal
Strobe signal indicating that address information is provided in the address
data bus (7:0) of the sub CPU
Chip select signal from the sub CPU
Interrupt request for the sub CPU
Sub CPU WR signal
Sub CPU RD signal
Connected to the multiplex bus of the sub CPU address data
Connected to the multiplex bus of the sub CPU address data
Connected to the multiplex bus of the sub CPU address data
Connected to the multiplex bus of the sub CPU address data
Digital circuit GND
Digital circuit power supply
Connected to the multiplex bus of the sub CPU address data
Connected to the multiplex bus of the sub CPU address data
Connected to the multiplex bus of the sub CPU address data
Connected to the multiplex bus of the sub CPU address data
Not used
Digital circuit GND
Digital circuit power supply
Control output for rough servo
7-bit PWM output terminal for FG servo
5-bit PWM output terminal for velocity servo
PWM output terminal for phase servo
Rotational pulse input from the spindle motor
Not used
XDV-M8357ZT/UC
1
2
3
4
5
Pin No.
164
165
166
167
168
169
170
171
172
173
174,175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
Pin Name
GND
XRESET
AGND
NC
VRB
AGND
AIN
NC
VRC
VRT
AVDD
VDD
GND
SEDI
SEDO
TMC1
VCOCLK
GND
VDD
ASC
APC
ATC
AFC
BMODE3
DUTY50
FSX/STATUS4
EFLG/STATUS3
DMCK/RF_A
GND
ADD7/PD7
ADD6/PD6
ADD5/PD5
ADD4/PD4
ADD3/PD3
ADD2/PD2
ADD1/PD1
ADD0/PD0
BMODE0
DEFECT
T_DET
PC7/STATUS2
PC6/STATUS1
PC5/STATUS0
VDD
6
I/O
I
I
I
I
I
I
O
I
I
O
O
O
O
I
O
I/O
I/O
O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
I
O
O
O
O
7
8
Function and Operation
Digital circuit GND
Terminal for initializing the entire LSI system
GND for A/D converter
Not used
Not used
GND for A/D converter
Analog RF signal input terminal to A/D converter
Not used
Reference voltage input terminal for A/D converter
Not used
Power supply for A/D converter
Digital circuit power supply
Digital circuit GND
Serial data input after BITABI decoding
Serial data output after BITABI decoding
Terminal test control terminal
System clock signals of the spindle and demodulator
Digital circuit GND
Digital circuit power supply
Outputs the frequency error of the sync cycle as a PWM pulse
Outputs the phase error of the PLL as a PWM pulse
Outputs the DC error of the RF signal as a PWM pulse
Outputs the frequency errors of VCOCLK and reference clock as PWM pulses
Sets which test is done in the test mode
Outputs a duty 50% pulse at any time
Not used
Not used
Reference clock input terminals of the spindle and PLL for DVD double-speed
playback
Digital circuit GND
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Sets which test is done in the test mode
External defect signal input
Not used
Not used
Not used
Not used
Digital circuit power supply
A
B
C
D
*PD4995A
1
52
*TC7SET04FUS1
E
208
53
1
5 VCC
2
157
104
4
F
156
105
GND 3
XDV-M8357ZT/UC
5
6
7
8
103
1
2
3
*M5M51008DKV-70HI
A
*PD6531A
*PD6520A
A11 1
32 oe
A9 2
31 A10
A8 3
30 s!
A13 4
29 DQ8
w 5
28 DQ7
A15 1
48
A14 2
47 BYTE
A13 3
46
S2 6
VCC
NC
A16
A14
C
A0~A16
DQ1~DQ8
8 w
s!,S2
9 oe
VCC
10 GND
NC
11
:Address input
:Data input/output
:Write control input
:Chip select input
:Output enable input
:Power supply
:GND
:Not used
A11
5
44 DQ7
A10
6
43 DQ14
A9
7
42
A8
8
41 DQ13
NC
9
45 DQ15/A-1
DQ0-DQ15 :Data input/output
A0-A18,A-1 :Address input
RY/BY :Ready/busy output
BYTE :8bit,16bit mode select
OE :Output enable
WE :Write enable
CE :Chip enable
RESET:Reset
NC 10
27 DQ6
RESET 12
26 DQ5
NC 14
D
A5 15
18 A2
A4 16
17 A3
34
DQ10
A18 16
33
DQ2
A17 17
32
DQ9
A7 18
31
DQ1
A6 19
30
DQ8
A5 20
29
DQ0
A4 21
28
OE
A3 22
27
VSS
A2 23
26
CE
A1 24
25
A0
*MAX662AESA
C1-
1
8
SHDN
C1+
2
7
GND
C2-
3
6
VOUT
5
VCC
E
+
ERROR
AMP
C2+
4
OSCILLATOR
F
104
XDV-M8357ZT/UC
1
2
VCC
RY/BY 15
21 DQ1
19 A1
DQ4
37
DQ11
22 DQ2
A6 14
DQ12
38
DQ3
23 DQ3
20 A0
40 DQ5
39
36
24 GND
A7 13
DQ6
35
25 DQ4
A12 12
VSS
4
NC 13
A15 7
A16
A12
WE 11
B
4
3
4
5
6
7
8
- Pin Functions (PD3411A)
Pin No.
1
2
3
4-11
12
13,14
15
16-21
22
23-30
31
32-39
40
41,42
43
44-47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80-82
83,84
85
86
87-89
90
91
92
93
94
95
Pin Name
PB14
PB15
VSS
AD0-7
VSS
AD8,9
VCC
AD10-15
VSS
A0-7
VSS
A8-15
VSS
A16,17
VCC
A18-21
CS0
CS1
CS2
CS3
VSS
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
VSS
PA8
PA9
PA10
PA11
PA12
PA13
PA14
PA15
VCC
CK
VSS
EXTAL
XTAL
VCC
NMI
VCC
WDTOVF
RES
MD0-2
VCC
AVCC
AVREF
PC0-2
PC3
AVSS
PC4
PC5
PC6
PC7
I/O
I
I
I/O
I/O
I/O
O
O
O
O
I
I
I
I
O
I
O
I
O
I
I
I
I
I
I
I
I
I
I
Function and Operation
MY-Chip interruption #1
AV Chip interruption #0
GND
Data bus
GND
Data bus
Power supply terminal
Data bus
GND
Address bus
GND
Address bus
GND
Address bus
Power supply terminal
Address bus
Not used
CARNET 4 chip select
External memory area chip select
MY-Chip chip select
GND
DVD EDC error detection
Flash ROM write enable
AV Chip chip select
External wait input
Low Byte write pulse
High Byte write pulse
Read pulse
Serial data latch pulse
GND
Audio output last step mute
RS-232 ready for sending output
AV Chip interruption #1
Communication response to BUS microcomputer
DMA CH0 transfer request
DMA CH0 transfer request
DMA CH0 transfer request
DMA CH0 transfer request
Power supply terminal
Not used
GND
Clock oscillator
Clock oscillator
Power supply terminal
Not used
Power supply terminal
Not used
Chip enable of after power on
Mode 2
Power supply terminal
Power supply terminal
Power supply terminal
Not used
Data lead enable
GND
V field discrimination signal input
Test mode entry
Communication request from BUS microcomputer
Request of RS-232 ready for communicating
A
B
C
D
E
F
XDV-M8357ZT/UC
5
6
7
8
105
1
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Function and Operation
GND
STEP 2 DMA transfer DREQ
Power supply terminal
Power supply terminal
Transfer end interruption
AV Chip interruption #2
STEP 2 receive interruptio n
STEP 2 transmit interruption #1
CARNET4 chip select
CARNET4 chip power
GND
Serial bus data input
Serial bus data output
RS232C RxD
RS232C TxD
Serial bus clock input/output
MY-Chip interruption #0
*PD3411A
4A
4Y
3B
3A
3Y
14
13
12
11
10
9
8
1
2
3
4
5
6
7
2A
2B
2Y
112
1Y
29
4B
1
28
*TC74VHC00FTS1
1B
B
I/O
4
VCC
A
Pin Name
VSS
PB0
PB1
VCC
PB2
PB3
PB4
PB5
PB6
PB7
VSS
PB8
PB9
PB10
PB11
PB12
PB13
3
1A
Pin No.
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
2
C
56
GND
84
57
85
D
*TC74VHC139FT
VCC
2G
2A
2B
2Y0
2Y1
2Y2
2Y3
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
1G
1A
1B
1Y0
1Y1
1Y2
1Y3
GND
E
F
106
XDV-M8357ZT/UC
1
2
3
4
5
6
10
11
VssQ
DQ7
7
21
22
A10
A0
A1
25
20
A11
26 Vss
27 A4
28 A5
29 A6
30 A7
31 A8
32 A9
33 NC
34 CKE
OUTPUT
MULTIPLEXER
AND
DIVIDERS
CPU
PLL
Vcc
19
CS
35 CLK
CPU
EPROM
TABLE
UTIL
PLL
23
18
RAS
SYS
PLL
24
17
CAS
37 NC
36 UDQM
CONFIGURATION
EPROM AND
TEST LOGIC
A3
16
WE
38 VccQ
39 DQ9
40 DQ10
41 VssQ
42 DQ11
43 DQ12
6
A2
14
15
LDQM
13
9
DQ6
44 VccQ
45 DQ13
14
12
8
DQ5
CLK : System clock
cs : Chip select
CKE : Clock enable
A0-A10 :Address input
A11 : Bank select address input
ras : Row address strobe
cas : Column address strobe
we : Write enable
UDQM,LDQM : Data input/output mask
DQi : Data input/output
15
DQ8
7
VccQ
VssQ
46 DQ14
47
48 DQ15
SHUTDOWN S2/
SUSPEND VDD
/OE
VccQ
5
4
VssQ
49 DQ16
CLKC
6
3
DQ2
50 Vss
1
DQ4
2
16
DQ3
1
Vcc
DQ1
5
7
8
*CY2292SI-1A0
SI
SO
GND
CLKA
CLKB
13
12
11
10
9
2
3
4
5
6
7
8
VDD
GND
XTAL
IN
XTAL
OUT
XBUF
CLKD
CPU
CLK
A
B
OSC
C
*MSM56V16160DP-10TS
D
E
F
XDV-M8357ZT/UC
8
107
1
2
3
4
- Pin Functions (MB86373BPFV-G-BI)
Pin No.
1
2
3
4-9
10
11
12
13
14
15
16
17
18
19
20
21-25
26
27
28-32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57-59
60
61
62
63
64
65
66
67
68,69
70
71
72
73
74-77
78
79
A
B
C
D
E
F
108
Pin Name
CLKSEL
DIGCPN7
VSS
DIGCPN6-1
VDD
DIGCPN0
RBSEL
XHS
XVS
VSS
XRESET
XLDCSYNC
KEY
PD
VFLD
DIGCOMP9-5
VSS
VDD
DIGCOMP4-0
DACK
NC
VSSA3
ANAC
VDDA3
VSSA2
ANAY
VDDA2
VREF
VRO
VDDA4
VSSA1
ANACOMP
VDDA1
BF
XBLK
TEST4
VSS
TEST0
TEST1
DAIIN
CDDATA
CDLR
CDBCK
AODATA3-1
VSS
VDD
AODATA0
AOPCM
AODAI
LRCK
AOMCK
BCK
TEST2,3
NC
XDSPRST
VSS
TEST5
NC
SD7
VDD
I/O
I
O
O
O
O
O
O
I
I
O
O
O
O
O
O
O
O
I
O
O
O
O
O
I
I
I
I
I
I
O
O
O
O
O
O
O
I
I
O
I
Function and Operation
ON/OFF signal of PLL
Digital component signal output
GND
Digital component signal output
2.5V Power supply
Digital component signal output
Cb, Cr identification signal of during digital component signal output
Horizontal synchronizing output signal
Vertical synchronizing output signal
GND
Reset
External synchronizing signal input (LD mode)
KEY signal for LD, OSD overlay (LD mode)
Phase comparing result output signal of horizontal synchronous
Field discrimination signal of digital signal output
Digital composite signal output
GND
2.5V Power supply
Digital composite signal output
27MHz clock output terminal
Not used
GND (D/A converter)
Analog color (C) output signal
2.5V power supply (internal D/A converter only)
GND (D/A converter)
Analog brightness (Y) output signal
2.5V Power supply (internal D/A converter only)
Reference voltage for D/A converter
D/A converter inner current set terminal
2.5V Power supply (internal D/A converter only)
GND (D/A converter)
Analog composite output terminal
2.5V Power supply (internal D/A converter only)
Burst flag signal
H/V complex blanking signal
Open
GND
Open
Test terminal
External input digital data input (SPDIF)
External input audio data input (for CD)
External input data channel clock input (for CD)
External input data clock input (for CD)
Audio decode data
GND
2.5V Power supply
Audio decode data
Digital audio interface output
Digital audio interface output
Data channel clock for D/A, digital filter
Master clock for D/A, digital filter
Bit clock for D/A, digital filter
open
Not used
Open
GND
Open
Not used
Parallel data input
2.5V Power supply
XDV-M8357ZT/UC
1
2
3
4
5
Pin No.
80-84
85
86,87
88
89
90
91
92-95
96
97
98-102
103-106
107
108-113
114
115-118
119
120,121
122
123
124
125,126
127-129
130
131
132
133
134
135
136
137
138-141
142
143
144
145
146
147
148
149
150
151
152
153
154
155-158
159
160
161
162
163
164
165
166
167
168
169
170
Pin Name
SD6-2
VSS
SD1,0
XERR
XSACK
XTEST
SREQ
HADRS10-7
VSS
VDD
HADRS6-2
HDATA15-12
VSS
HDATA11-6
VDD
HDATA5-2
VSS
HDATA1,0
BUSSEL
XOSDACK
XOSDREQ
HCPUSEL1,0
XINT3-1
VSS
VDD
XINT0
XEXTRDY
HRW
HCLKIN
XHCS
XHAS
XHBE3-0
VSS
MDRADR4
MDRADR3
MDRADR5
MDRADR2
VDD
VSS
MDRADR6
MDRADR1
MDRADR7
MDRADR0
MDRADR8
VSS
TEST6-9
MDRADR10
MDRADR9
MDRADR11
XMDRCS
MDRCKE
VSS
VDD
XMDRRAS
MDRCLK
VSS
MDRCLKIN
XMDRCAS
6
I/O
I
I
I
I
I
O
I
I
I/O
I/O
I/O
I/O
I
I
O
I
O
O
O
I
I
I
I
I
O
O
O
O
O
O
O
O
O
I
O
O
O
O
O
O
O
I
O
7
8
Function and Operation
Parallel data input
GND
Parallel data input
Error input signal
Acknowledge signal
Test terminal
Data request signal
CPU address bus signal
GND
2.5V Power supply
CPU address bus signal
CPU data bus signal
GND
CPU data bus signal
2.5V Power supply
CPU data bus signal
GND
CPU data bus signal
Bus width select signal
OSD data acknowledge signal
OSD data request signal
CPU select signal
Interruption request signal to CPU
GND
2.5V Power supply
Interruption request signal to CPU
Acknowledge signal to CPU
CPU read/write signal
Host clock input
LSI chip select signal
CPU address status
CPU byte enable signal
GND
Address signal for SDRAM
Address signal for SDRAM
Address signal for SDRAM
Address signal for SDRAM
2.5V Power supply
GND
Address signal for SDRAM
Address signal for SDRAM
Address signal for SDRAM
Address signal for SDRAM
Address signal for SDRAM
GND
Test terminal
Address signal for SDRAM
Address signal for SDRAM
Address signal for SDRAM
Chip select signal for SDRAM
Clock enable signal for SDRAM
GND
2.5V Power supply
RAS signal for SDRAM
Clock output signal for SDRAM
GND
Clock input signal for SDRAM
CAS signal for SDRAM
A
B
C
D
E
F
XDV-M8357ZT/UC
5
6
7
8
109
1
Pin No.
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
A
B
C
D
2
Pin Name
XMDRDQM1
VSS
XMDRWE
XMDRDQM0
MDRDAT8
VSS
MDRDAT7
MDRDAT9
MDRDAT6
MDRDAT10
MDRDAT5
VSS
VDD
MDRDAT11
MDRDAT4
MDRDAT12
MDRDAT3
MDRDAT13
VSS
MDRDAT2
MDRDAT14
MDRDAT1
MDRDAT15
MDRDAT0
VSS
NC
ICK27M
VSS
OCK27M
VSSA
VDDA
ILPF
MLPF
OLPF
OVCO
VSS
XPLLRST
XSYNCRST
I/O
O
O
O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
O
O
I
O
I
I
3
4
Function and Operation
Input mask/output enable signal for SDRAM
GND
Write enable signal for SDRAM
Input mask/output enable signal for SDRAM
Data bus signal for SDRAM
GND
Data bus signal for SDRAM
Data bus signal for SDRAM
Data bus signal for SDRAM
Data bus signal for SDRAM
Data bus signal for SDRAM
GND
2.5V Power supply
Data bus signal for SDRAM
Data bus signal for SDRAM
Data bus signal for SDRAM
Data bus signal for SDRAM
Data bus signal for SDRAM
GND
Data bus signal for SDRAM
Data bus signal for SDRAM
Data bus signal for SDRAM
Data bus signal for SDRAM
Data bus signal for SDRAM
GND
Not used
System clock output
GND
System clock input
GND (VCO only)
2.5V Power supply (VCO only)
PLL section inverter output for audio
PLL section inverter input for audio
Phase detector output for audio
VCO input for audio clock
GND
PLL section reset signal
Connect to VDD
1
52
*MB86373BPFV-G-BI
53
208
104
157
156
105
E
F
110
XDV-M8357ZT/UC
1
2
3
4
11 Y8
12 Y7
8
13 Y6
14 Y5
16 Y3
15 Y4
7
17 Y2
18 Y1
19 G2
*TC74VHC541FTS1
6
20 VCC
5
A
*TC74VHC08FTS1
10 GND
9 A8
8 A7
7 A6
6 A5
5 A4
4 A3
3 A2
2 A1
1 g1
B
C
*TC74LCX245FTS1
14 VCC
1 1A
20 VCC
1 DIR
2 A1
19 oe
3 A2
18 B1
4 A3
17 B2
5 A4
16 B3
6 A5
15 B4
7 A6
14 B5
8 A7
13 B6
9 A8
12 B7
10 GND
11 B8
13 4B
2 1B
12 4A
3 1Y
4 2A
D
11 4Y
10 3B
5 2B
6 2Y
9 3A
7 GND
8 3Y
E
F
XDV-M8357ZT/UC
5
6
7
8
111
1
2
3
4
3
4
- Pin Functions (LC89513KP)
Pin No.
1
2-8
9
10-16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34-41
42
43
44
45-48
49
50-53
54
55
56
57-64
A
B
C
Pin Name
VSS
RA0-6
VSS
RA7-13
VSS
ra!#
rcs
rwe
roe
reset
XTALCK
VDD
C2PO
BCK
SDATA
LRCK
RS
rd
wr
cs
VSS
D0-7
PSRAM
int
DRQ
HD0-3
VSS
HD4-7
hrd
dten
VDD
IO0-7
I/O
O
O
O
O
O
O
I
I
I
I
O
I/O
I
I
I
I
I
O
O
O
O
I
O
Function and Operation
GND
Address signal output
GND
Address signal output
GND
Address signal output
Chip select
Data write signal
Data read signal
Reset input
Oscillator input
Power supply
C2 pointer input
Serial data clock input
Serial data output
44.1kHz strobe input
Register select signal input
Data read signal input
Data write signal input
Chip select
GND
CPU data signal
SRAM select
Interrupt request signal output
DRQ signal output
Data output
GND
Data output
Data reading request input
Data enable output
Power supply
Data buffer RAM data signal
*LC89513KP
64
D
49
1
48
16
33
E
17
32
F
112
XDV-M8357ZT/UC
1
2
5
6
7
8
- Pin Functions (PE5272A)
Pin No.
1
2
3
4
5
Pin Name
SENS25
SENS3
NC
AVSS
XSRSENS
I/O
I
I
Format
O
C
6
7
8
9
10
11
12
13
14
15
XADEN
AVREF1
SWREG
XILL
VADCONT
SI
SO
SCK
NC
XRDY
O
C
O
C
O
I
O
O
C
O
C
16
17
18,19
20
21-25
26
27
28
29-32
33
34
35
36-39
40
41-46
47
XRES
XMRES
NC
VIOC
NC
SYSMUTE
ANSW
XRMUTE
NC
VSS
DEST2
XVMUTE
NC
AV8CONT
NC
LT1
O
O
C
C
O
C
O
O
O
C
C
C
I
O
C
O
C
48-51
52,53
54
55
56
57
58,59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
NC
FANPW1,2
NC
IEPW
IEDO
IEDI
NC
XRST
RMIN
XASEN
XMBSEN
XBSEN
XCLOSSEN
XEJ
XMAG
VDD
X2
X1
IC
NC
TESTIN
AVDD
AVREF0
C
C
I
O
C
O
O
I
C
C
I
I
I
I
I
I
I
I
I
I
Function and Operation
VD short sense 2.5V
VD short sense 3V
Open
GND
SWREG information output to mechanism controller
(H : Off, L : On)
AVREF0 control output
D/A converter reference voltage
System power supply voltage
Open
Servo, liquid tilt power supply, audio power supply control output
System controller communication data input
System controller communication data output
System controller communication clock output
Open
Communication request to system controller
(L : Communication permission)
System reset output (L : Reset)
Mechanism controller reset output
Open
Image changeover switch(H:External through hole,L:MMCH output)
Open
Mute output of AVC-LAN
Analog switch control output
Mute output for rear RCA
Open
GND
Destination set input
Front video mute output (H : Mute on)
Open
Power supply control output of audio
Open
Communication response from system controller
(L : Communication permission)
Open
Power control output of FAN
Open
IE-BUS driver STBY control output
Data output for IE-BUS driver
Data input for IE-BUS driver
Open
System reset input
Remote control input
ACC on/off state detection input (7, 7.5 V sense)
Backup state detection input (8.5 V sense)
Backup state detection input (7, 7.5 V sense)
Door detection (L : Door close)
Eject SW detection (L : Eject key)
Magazine insert detection (L : Magazine)
Positive power supply
System clock oscillation
System clock oscillation input
Connect to GND
Open
Chip test mode input
A/D converter analog power supply
A/D converter reference voltage
A
B
C
D
E
F
XDV-M8357ZT/UC
5
6
7
8
113
1
Pin No.
76
77
78
79
80
A
2
Pin Name
STEMP
BTEMP
LOTEMP
DEST
SENS9
I/O
I
I
I
I
I
Format
3
Function and Operation
System controller section high-temperature sense A/D input
BUS microcomputer section high-temperature sense A/D input
Low-temperature sense A/D input
Destination set A/D input
VD short sense 9V group
*PE5272A
80
4
Format
C
61
1
60
20
41
Meaning
C MOS
B
21
40
*LC35256FT-70U
C
oe 22
21 A10
20 ce
A11 23
A9 24
19 I/O8
A8 25
18 I/O7
A13 26
17 I/O6
we 27
16 I/O5
VCC 28
15 I/O4
A14 1
14 GND
D
A12 2
A7 3
A6 4
E
A5 5
ce
oe
we
A0~A14
VCC
VSS
I/O1~I/O8
:Chip enable input
:Output enable input
:Read/write input
:Address input
:Power supply
:GND
:Data input/output
13 I/O3
12 I/O2
11 I/O1
10 A0
A4 6
9 A1
A3 7
8 A2
F
114
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
7.3 EXPLANATION
7.3.1 OPERATIONAL FLOW CHART
Power ON
Magazine insertion and door closed state
A
VDD=5V
Pin 68
Y
XBSEN
Pin 64
XBSEN=L
B
XMBSEN
Pin 63
XMBSEN=L
XASEN
Pin 62
XASEN=L
Subsequently,
AVC-LAN enables
communication.
IEPW←Hi
Pin 55
C
SWREG←Hi
Pin 8
SENS9 > 1V
Pin 80
Y
D
SENS3 > 1V
Pin 2
Y
SENS25 > 1V
Pin 1
Y
XSRSENS(Pin 5)←Low
XRES(Pin 16)←Hi
XMRES(Pin 17)←Hi
Subsequently,
communication with
an internal system
controller starts.
E
150ms
In case of the movement as shown above,
communication with the system controller may
cause an error.
A DVD changer
can operate.
F
XDV-M8357ZT/UC
5
6
7
8
115
1
2
3
4
7.3.2 SYSTEM BLOCK DIAGRAM
- (7SP)
POWER SUPPLY(+B, ACC)
BUS
A
SIGNAL(SOUND)
GM-9027ZT-02/E
XDV-M8357ZT/UC
DVD
CHANGER
PWR
AMP
H/U
VISION
KEX-M9137ZT-02/UC
KEX-M9737ZT-02/UC
DISPLAY
B
(OTHER MAKERS)
PWR ANT
ECU
+B, ACC
(OTHER MAKERS)
C
D
E
F
116
XDV-M8357ZT/UC
1
2
3
4
5
6
7
8
8. OPERATIONS
A
Notes
CD-Rs may not
be playable in
this compact
disc player.
B
EJECT
C
D
E
F
XDV-M8357ZT/UC
5
6
7
8
117
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools:
Portions to be cleaned
DVD pickup lenses
Cleaning tools
Cleaning liquid : GEM1004
Cleaning paper : GED-008
Portions to be cleaned
Fans
Cleaning tools
Cleaning paper : GED-008
- Jigs List
Name
15P Extension cable
30P Extension cable
Extension cord
Extension cord
Extension cord
Extension cord
Clamp adjusting disc
Jig No.
GGD1177
GGD1171
GGD1398
GGD1348
GGD1240
GGD1169
GGV1018
Remarks
Adjustment
j
Adjustment
j
Adjustment
j
Adjustment
j
Adjustment
j
Adjustment
j
Skew adjustment
j
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2005
K-ZZA. APR. 2005 Printed in Japan
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Producer : Acrobat Distiller 4.05 for Macintosh Author : PMC Title : CRT3452 Creator : FrameMaker 6.0 Modify Date : 2005:04:26 11:00:39+09:00 Create Date : 2005:04:21 11:33:55 Subject : Linked Page Count : 118 Page Mode : UseThumbs Page Layout : SinglePageEXIF Metadata provided by EXIF.tools