RRV3262 XVGX3

User Manual: XVGX3

Open the PDF directly: View PDF .
Page Count: 96

Download
Open PDF In Browser	View PDF

PUSH OPEN

 STANDBY/ON

REVERSE
MODE

P.BASS

REC/STOP

FUNCTION

ORDER NO.


 OPEN/CLOSE

MIC

MAIN

MIC VOL

SUB

MIN

RRV3262

MAX

XV-GX3

STEREO DVD CASETTE DECK RECEIVER

XV-GX3
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model

Type

Power Requirement

Regional
restriction codes
(Region No.)

The voltage can be
converted by the
following method.

XV-GX3

DFLXJ

AC 110-120V/220-230V/240V

3

With the voltage selector

XV-GX3

DDXJ/RD

AC 110-127V/220-230V/240V

4

With the voltage selector

XV-GX3

DDXJ/RB

AC 110-120V/220-230V/240V

2

With the voltage selector

XV-GX3

MTXJ

AC 220-230V

3

–––––

Remarks

For details, refer to "Important Check Points for good servicing".
PIONEER CORPORATION

4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936

PIONEER CORPORATION 2005
T-ZZS NOV. 2005 printed in Japan

1

2

3

4

SAFETY INFORMATION
A

This service manual is intended for qualified service technicians ; it is not meant for the casual doit-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trained to properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and
may void the warranty. If you are not qualified to perform the repair of this product properly and
safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING !
THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1
BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR
CLASS 1.
A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS.

B

LASER DIODE CHARACTERISTICS
FOR DVD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 650 nm
FOR CD : MAXIMUM OUTPUT POWER : 7 mW
WAVELENGTH : 780 nm

C

LABEL CHECK

DDXJ/RB,
DDXJ/RD,
MTXJ type
VRW1699

DFLXJ type
VRW2159

D
Printing on Rear Panel

Additional Laser Caution
1. Laser Interlock Mechanism
• Loading switch (S101 on the LOAB Assy) is used for interlock
mechanism of the laser.
When this switch turned ON in SW2 (CLOSE) side (OPEN signal is
0V and CLOSE signal is 3.5V), a laser becomes the status which can
completely oscillation.
Furthermore, the laser completely oscillates in the disc judgment and
disc playback.
When player is power ON state and laser diode is not completely
oscillating, 780nm laser diode is always oscillating by half power.
• Laser diode is driving with Q307 (650nm LD) and Q308 (780nm LD)
on the DVDM Assy.
Therefore, when short-circuit between the emitter and collector of these
transistors or the base voltage is supplied for transistors turn on, the
laser oscillates. (failure mode)
• In the test mode ∗ , there is the mode that the laser oscillates except
for the disc judgment and playback. LD ON mode in the test mode
oscillates with the laser forcibly.
The interlock mechanism mentioned above becomes invalid in this
mode.

E

2. When the cover is open, close viewing through the objective lens with
the naked eye will cause exposure to the laser beam.

F

∗ : Refer to page 65.

2

XV-GX3
1

2

3

4

5

6

7

8

[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
A

1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.

B

When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.

C

7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
0 Safe environment should be secured during servicing.

D

When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.

2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.

3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.

E

4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.

5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

F

3

XV-GX3
5

6

7

8

1

2

3

4

CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SPECIFICATIONS ............................................................................................................................................ 5
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6
2.1 PACKING SECTION .................................................................................................................................. 6
2.2 EXTERIOR SECTION................................................................................................................................ 8
2.3 FRONT PANEL SECTION ....................................................................................................................... 10
2.4 05 LOADER ASSY................................................................................................................................... 12
2.5 TRAVERSE MECHANISM ASSY-S ......................................................................................................... 14
2.6 DECK MECHANISM ASSY ..................................................................................................................... 15
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .......................................................................................... 16
3.1 BLOCK DIAGRAM ................................................................................................................................... 16
3.2 OVERALL WIRING CONNECTION DIAGRAM and LOAB ASSY ........................................................... 18
3.3 DVDM ASSY (1/2).................................................................................................................................... 20
3.4 DVDM ASSY (2/2).................................................................................................................................... 22
3.5 MAIN ASSY (1/4) ..................................................................................................................................... 24
3.6 MAIN ASSY (2/4) ..................................................................................................................................... 26
3.7 MAIN ASSY (3/4) ..................................................................................................................................... 28
3.8 MAIN ASSY (4/4) ..................................................................................................................................... 30
3.9 DISPLAY and MIC ASSYS....................................................................................................................... 32
3.10 WAVEFORMS ........................................................................................................................................ 34
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 35
4.1 LOAB ASSY ............................................................................................................................................. 35
4.2 DVDM ASSY ............................................................................................................................................ 36
4.3 MAIN ASSY ............................................................................................................................................. 38
4.4 DISPLAY ASSY........................................................................................................................................ 42
4.5 MIC ASSY ................................................................................................................................................ 44
5. PCB PARTS LIST ........................................................................................................................................... 46
6. ADJUSTMENT ............................................................................................................................................... 57
6.1 DECK SECTION ...................................................................................................................................... 57
6.1.1 ADJUSTMENT CONDITION ............................................................................................................. 57
6.1.2 PLAYBACK and RECORDING SECTION ......................................................................................... 58
6.2 DVD SECTION......................................................................................................................................... 60
6.2.1 ADJUSTMENT ITEMS AND LOCATION ........................................................................................... 60
6.2.2 JIG AND MEASURING INSTRUMENTS........................................................................................... 60
6.2.3 NECESSARY ADJUSTMENT POINTS ............................................................................................. 61
6.2.4 TEST MODE ...................................................................................................................................... 62
6.2.5 MECHANISM ADJUSTMENT............................................................................................................ 63
7. GENERAL INFORMATION ............................................................................................................................. 65
7.1 DIAGNOSIS ............................................................................................................................................. 65
7.1.1 TEST MODE ...................................................................................................................................... 65
7.1.2 DISPLAY SPECIFICATION OF THE TEST MODE............................................................................ 66
7.1.3 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY ............................................................ 67
7.1.4 SPECIFICATION OF THE MODEL INFORMATION DISPLAY .......................................................... 68
7.1.5 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE ............................................................. 69
7.1.6 SERVICE TEST MODE ..................................................................................................................... 70
7.1.7 METHOD FOR DIAGNOSING DEGRADATION OF THE LDs ON THE PICKUP ASSY ................... 72
7.1.8 DVD TROUBLE SHOOTING.............................................................................................................. 73
7.1.9 ID NUMBER AND ID DATA SETTING ............................................................................................... 76
7.1.10 DISASSEMBLY................................................................................................................................ 79
7.2 PARTS...................................................................................................................................................... 89
7.2.1 IC ....................................................................................................................................................... 89
8. PANEL FACILITIES ........................................................................................................................................ 92

A

B

C

D

E

F

4

XV-GX3
1

2

3

4

5

6

7

8

1. SPECIFICATIONS
Amplifier section

•

Front . . . . . . . . . . . . . . . . . . 100 W per channel
(1 kHz, 10 % T.H.D., 6 Ω)

Disc section

Digital audio
characteristics . . . . . . . . DVD fs: 96 kHz, 24-bit
Type . . . DVD system, Video CD/Super VCD system
system and Compact Disc digital audio system
Frequency response . . . . . . . . . 4 Hz to 44 kHz
S/N ratio. . . . . . . . . . . . . . . . . . . . . . . . . 107 dB
Dynamic range. . . . . . . . . . . . . . . . . . . . . 94 dB
Total harmonic distortion . . . . . . . . . . . 0.007 %
Wow and Flutter . . . . . . . Limit of measurement
(±0.001 % W.PEAK) or less (JEITA)

Cassette deck section

Systems. . . . . . . . . . . 4 track, 2-channel stereo
Heads . . . . . . . . . Recording/playback head x 1
Erasing head x 1
Motor . . . . . . . . . . . . . . . . . DC servo motor x 1
Tape types . . . . . . . . . . . . . . . . Type I (Normal)

FM tuner section

Frequency range . . . . . . 87.5 MHz to 108 MHz
Antenna . . . . . . . . . . . . . . . . 75 Ω, unbalanced

A

B

• Accessories (Stereo DVD Cassette
Deck Receiver)

AM tuner section

Frequency range
With 9kHz step . . . . . . . . 1 kHz to 1,602 kHz
With 10kHz step (Singapore, Malaysia,
Taiwan, Indonesia and Philippines models
only) . . . . . . . . . . . . . . 530 kHz to 1,700 kHz
Antenna . . . . . . . . . . . . . . . . . . . Loop antenna

Remote control . . . . . . . . . . . . . . . . . . . . . . . . 1
Dry cell batteries (AA/R6) . . . . . . . . . . . . . . . . 2
Video cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . 1
FM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Power cord
Singapore, Malaysia, Taiwan, Indonesia and
Philippines models . . . . . . . . . . . . . . . . . . . . 2
All other models . . . . . . . . . . . . . . . . . . . . . . 1
Power Plug Adapter(DDXJ/RD only) . . . . . . . 1
Operating instructions

“DTS” and “DTS 2.0” are trademarks of Digital
Theater Systems, Inc.
Manufactured under license from Dolby
Laboratories.“Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.

C

Note
• Specifications and design subject to
possible modification without notice, due
to improvements.

Accessories
• Power cord
DFLXJ only
(ADG7097)

• FM Antenna (ADH7030) • Video Cord
(L = 1.5m) (XDE3046)

• Power Plug Adapter
DDXJ/RD only
(XKM3001)

D

Disc / content format playback
compatibility
This player is compatible with a wide range of disc types (media)
and formats. Playable discs will generally feature one of the following
logos on the disc and/or disc packaging. Note however that some
disc types, such as recordable CD and DVD, may be in an unplayable
format. See the Disc compatibility table below for more information.

SLEEP

DISPLAY

MUTE
CLEAR
SHIFT

RETURN
TUNE

KARAOKE
SFC

SOUND
MODE

0

DVD
MENU

ENTER

ST
HOME
MENU

ST

TUNE

TOP MENU

ZOOM

9
ECHO

8
7

SYSTEM SETUP

VOLUME

6

ANGLE
SUBTITLE
AUDIO

3
2

5

1

4

TAPE
RDM

• Remote Control
(AXD7429)

STANDBY/ON

• Dry Cell Batteries

LINE

Yellow

• AM Loop Antenna
(ATB7013)

TUNER

• Power cord
(ADG1154)

RPT

•

DVD/CD

•

PGM

•

P.BASS

•

Miscellaneous

Power requirements
Singapore, Malaysia, Taiwan, Indonesia,
Philippines, Mexico and South America
models . . . AC 110-120/220-230/240 V
(switchable), 50/60 Hz
Power consumption . . . . . . . . . . . . . . . . 124 W
(0.32 W in standby)
Power requirements
Thai model
. . . AC 220-230V (non switchable), 50 Hz
Power consumption . . . . . . . . . . . . . . . . 120 W
(0.32 W in standby)
Power requirements
Middle East and South Africa models
. . . AC 110-127/220-230/240 V
(switchable), 50/60 Hz
Power consumption . . . . . . . . . . . . . . . . 126 W
(0.32 W in standby)
Dimensions (Stereo DVD Cassette
Deck Receiver). . .360 (W) x 145 (H) x 364 (D) mm
Weight (Stereo DVD Cassette Deck Receiver)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6 kg

FM/AM

•

• Also compatible with KODAK Picture CD
This player supports the IECís Super VCD standard for
superior picture quality, dual soundtracks, and widescreen
support.

E

VIDEO

CD

Super Video CD (Super VCD)

About DualDisc playback
DVD-Video DVD-R

Audio CD Video CD

•
•

A DualDisc is a new two-sided disc, one side of which
contains DVD content (video, audio, etc.) while the other
side contains non-DVD content such as digital audio
material. The non-DVD, audio side of the disc is not
compliant with the CD Audio specification and therefore
may not play. The DVD side of a DualDisc plays in this
product (excluding DVD-Audio content). For more detailed
information on the DualDisc specification, please refer to
the disc manufacturer or disc retailer.

DVD-RW

CD-R

CD-RW

Fujicolor CD

is a trademark of Fuji Photo Film Co. Ltd.
is a trademark of DVD Format/Logo
Licensing Corporation

5

XV-GX3
5

6

F

7

8

1

2

3

4

2. EXPLODED VIEWS AND PARTS LIST
NOTES:
A

Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The
mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)

2.1 PACKING SECTION
DFLXJ only

DDXJ/RD only

9

DFLXJ only
4

23

8
5

MTXJ only
7

B

14
20
6
14

10

13

14

Yellow

C

15
17

11
19

12
D

1
Junction

18

E

16

MTXJ only

21
F

22

2

6

XV-GX3
1

2

3

4

5

6

7

8

(1) PACKING SECTION PARTS LIST
Mark No.
NSP 1
NSP 2
3
>
4
>
5
6
7
8
9
10
11
NSP 12
13
NSP 14
15

Description
Getter 2CH
Label
••••••
Power Cord
Power Cord

Mark No.

Part No.
See Contrast table (2)
VRW1629

16
17
18
19
20

ADG1154
See Contrast table (2)

FM Antenna
ADH7030
Operating Instructions (English) See Contrast table (2)
Operating Instructions (Chinese)See Contrast table (2)
Caution Card SB
See Contrast table (2)
AM Loop Antenna
ATB7013
Remote Control
Dry Cell Batteries (AA/R6)
Video Cord
Polyethylene Bag
Pad L

21
NSP 22
23

Description

Part No.

Pad R
Packing Sheet
Packing Case
Battery Cover
Service Map (Thai)

AHA7451
AHG7010
See Contrast table (2)
VNK4998
See Contrast table (2)

Polyethylene Bag
Warranty Card (Thai)
Power Plug Adapter

See Contrast table (2)
See Contrast table (2)
See Contrast table (2)

A

B

AXD7429
VEM1031
XDE3046
Z21-038
AHA7450

(2) CONTRAST TABLE
DFLXJ, DDXJ/RB, DDXJ/RD and MTXJ are constracted the same except for the following:
Mark

No.

NSP

1
5
7

>

DFLXJ

DDXJ/RB

DDXJ/RD

MTXJ

Getter 2CH
Power Cord
Operating Instructions
(English)
Operating Instructions
(Spanish)

AAX8096
ADG7097
ARB7347

AAX8096
Not used
ARB7347

AAX8097
Not used
Not used

AAX8096
Not used
Not used

Not used

Not used

ARC7653

Not used

Not used

Not used

Not used

ARC7654

ARC7655

Not used

Not used

Not used

9
18
20

Operating Instructions
(Thai)
Operating Instructions
(Chinese)
Caution Card SB
Packing Case
Service Map (Thai)

ARM7064
XHD3577
Not used

Not used
XHD3580
Not used

Not used
XHD3579
Not used

Not used
XHD3578
XRY3005

21
22

Polyethylene Bag
Warranty Card (Thai)

Not used
Not used

Not used
Not used

Not used
Not used

AHG7031
XRY3004

23

Power Plug Adapter

Not used

Not used

XKM3001

Not used

7

7
8

NSP

Description

C

D

E

F

7

XV-GX3
5

6

7

8

1

2

3

4

2.2 EXTERIOR SECTION
29

27
29

29

A

28

26

29

29

33
16
3

G

DFLXJ
DDXJ/RB
DDXJ/RD
only

6

14

10
B

29

35

H

Refer to
"2.3 FRONT PANEL
SECTION".

5

I

29

J

29

K
L
M

7

N

C

2

25

G

C

29

K
L

9 30
M

O

21

N

F

P

P

A

29

29

24

Q

29

E

12
31

19

I
H

29

J

32

13

34

O

29

D

19
18
B

A

B

C

C

Fans
Cleaning paper
GED-008

20

19

D

17
D

29

29
29

4

29

F

29

B

8

18

E

E

15
1

11

F

CONTACT SIDE

NON-CONTACT
SIDE

Refer to
"2.4 05 LOADER ASSY".

Q

23

29
23

22

8

XV-GX3
1

2

3

4

29

5

6

7

8

(1) EXTERIOR SECTION PARTS LIST
Mark No.

Description

Mark No.

Part No.

1
2
3
4
5

DVDM Assy
MAIN Assy
FM/AM TUNER Unit
Power Transformer
Fuse (FU2, FU3)

AWM7966
See Contrast table (2)
AXX7173
ATS7406
See Contrast table (2)

6
7
8
9
10

Fuse (FU1)
Fuse (FU4)
25P F.F.C/60V
27P F.F.C/60V
11P F.F.C/60V

See Contrast table (2)
REK1029(T5A)
ADD7520
ADD7521
ADD7523

11
12
NSP 13
14
NSP 15

Connector Assy
DC Fan Motor
05 LOADER Assy
VS Knob
Bottom Chassis

PG05KK-E45
XXM3009
VWT1219
See Contrast table (2)
ANA7186

16
17
18
19
NSP 20

Rear Panel DFL
Heatsink Holder
Side Angle A
FET Bracket A
Heat Sink

See Contrast table (2)
AND7079
ANG7336
ANG7418
ANH7184

>
>
>
>

21
22
23
24
25

Description

Part No.

Ring
S Cover
LEG Cushion
VOL Knob Assy
Tray Panel

ABH7213
AEB7262
XEB3028
AAB7263
AAK8304

26
27
NSP 28
29
30

Bonnet Case
Caution Label
ID Label Assy
Screw
Screw

AZN8013
See Contrast table (2)
VXW1002
BBZ30P080FNI
BBZ30P140FTC

31
32
NSP 33
34
35

Screw
Screw
Label
Cord Clamper
Fuse Card

BBZ30P300FTC
BCZ40P060FNI
VRW1629
RNH-184
See Contrast table (2)

A

B

C

(2) CONTRAST TABLE
DFLXJ and DDXJ/RB and DDXJ/RD and MTXJ are constracted the same except for the following:
Mark
>
>

NSP

No.

Description

2
5
6
14
16

MAIN Assy
Fuse (FU2, FU3)
Fuse (FU1)
VS Knob
Rear Panel

27
35

Caution Label
Fuse Card

DFLXJ

DDXJ/RB

DDXJ/RD

MTXJ

AWM8013
REK1025(T2A)
REK1028(T4A)
AAD7690
ANC8357

AWM8016
REK1025(T2A)
REK1028(T4A)
AAD7690
ANC8370

AWM8013
REK1025(T2A)
REK1028(T4A)
AAD7690
ANC8369

AWM8015
Not used
REK1025(T2A)
Not used
ANC8368

VRW2159
Not used

VRW1699
Not used

VRW1699
Not used

VRW1699
AAX2357

D

E

F

9

XV-GX3
5

6

7

8

1

2

3

4

A

CONTACT SIDE

NON-CONTACT
SIDE

2.3 FRONT PANEL SECTION
1

23

23

Refer to
"2.2 EXTERIOR
SECTION K ".

3

D

B

Refer to
"2.2 EXTERIOR
SECTION L ".
2
22
19
13
Refer to
"2.2 EXTERIOR
SECTION M ".

14
C

E
10
21

4

16

18

20

D

17
12
11
Refer to
"2.2 EXTERIOR
SECTION N ".
5

20

E

Refer to
"2.2 EXTERIOR
SECTION O ".

15

Refer to
"2.2 EXTERIOR
SECTION P ".

6

23

9

7

Refer to
"2.2 EXTERIOR
SECTION Q ".

8
Refer to
"2.6 DECK MECHANISM ASSY".

F

10

XV-GX3
1

2

3

4

5

6

7

8

FRONT PANEL SECTION PARTS LIST
Mark No.
1
2
3
4
5

Description

Part No.

DISPLAY Assy
MIC Assy
17P F.F.C/30V
5P F.F.C/60V
11P F.F.C/60V

AWU8275
AWU8276
ADD7410
ADD7522
ADD7523

Cable Assy
Cord With Plug
DECK Mechanism Unit
Door Spring_R
MIC Knob

ADE7118
DE010VE0
XYM3019
XBH3002
AAK8309

11
12
13
14
15

Front Panel Assy
Button Center (PLS)
Button L
Display Window
Deck Door

AXG7277
ADD7750
ADD7751
AAK8303
AAN7231

16
17
18
19
20

Ratch Spring R
Front Panel
Damper Assy
Pioneer Name Plate
LEG Cushion

ABH7131
AMB7904
AXA7052
VAM1129
XEB3028

6
NSP 7
8
9
10

A

B

C

21
22
23

Ratch Mold R
Screw with Washer
Screw

XMR3002
ABA7124
PPZ30P080FNI

D

E

F

11

XV-GX3
5

6

7

8

1

2

3

4

2.4 05 LOADER ASSY
Pickup leneses
Cleaning liquid
GEM1004
Cleaning paper
GED-008

Note :
Refer to
" Application of Lubricant".

A

2 Refer to
"2.5 TRAVERSE MECHANISM
ASSY-S".

8

6
8

8

To DVDM CN101 (Pickup)
To DVDM CN104 (Stepping Motor)

Daifree
GEM1036

To DVDM CN102 (Spindle Motor)

8

B

18
12
Lubricating Oil
GYA1001

24

3

20

13
A

23

22

17
16

19

22

C

21
15
22
To
DVDM CN103

7

A

10

14

11

D

A

9

Lubricating Oil
GYA1001

1

22

05 LOADER ASSY PARTS LIST
Mark No.

E

NSP 1
2
3
4
5

F

Description

Mark No.

Part No.

LOAB Assy
Traverse Mechanism Assy-S
Loading Motor Assy
• • • • •
• • • • •

VWG2346
DXX2568
VXX2912

6
7
8
9
10

Flexible Cable (24P)
Connector Assy 2P
Floating Rubber
Belt
Stabilizer

VDA2008
VKP2253
VEB1351
VEB1358
VNE2253

11
12
13
14
15

Loading Base
Float Base 04
Drive Cam
Gear Pulley
Loading Gear

VNL1917
VNL1968
VNL1919
VNL1921
VNL1922

12

Description

Part No.

16
17
18
19
20

Drive Gear
SW Lever
Clamper Plate 04
Bridge 04
Clamper 04

VNL1923
VNL1925
VNE2342
VNE2343
VNL1969

21
22
23
24

Screw
Screw
Tray
Clamp Magnet

JGZ17P028FTC
VBA1094
VNL1920
VMG1029

XV-GX3
1

2

3

4

5

6

7

8

Application of Lubricant
A

Lubricating Oil
GYA1001
Around the shaft

No. 11
Loading Base

B

Lubricating Oil
GYA1001

Lubricating Oil
GYA1001

Lubricating Oil
GYA1001

Lubricating Oil
GYA1001
Inner side of a ditch

No. 13
Drive Cam

Lubricating Oil
GYA1001
Inner side of a ditch
C

No. 13
Drive Cam

Lubricating Oil
GYA1001

Front View

Rear View

D

Daifree
GEM1036
Concave of unevenness

No. 23
Tray

Daifree
GEM1036
Concave of unevenness

No. 23
Tray

Inner side of a ditch

E

Daifree
GEM1036

Top View

Bottom View
Concave of unevenness

Side of the rib
Daifree
GEM1036

Daifree
GEM1036

F

13

XV-GX3
5

6

7

8

1

2

3

4

2.5 TRAVERSE MECHANISM ASSY-S
Pickup leneses
Cleaning liquid
1
GEM1004
Cleaning paper
GED-008

Note :
Refer to
" Application of Lubricant".

A

2

Note : When part #2 is replaced,
part #13 also need to be
replaced at the same time.
4

3
5

B

10
6

9

10
11

Silicone Adhesive
GEM1037

To DVDM CN102
(Spindle Motor)

To
DVDM CN101
(Pickup Assy)

11
C

12
7

To
DVDM CN104
(Stepping Motor)

CONTACT SIDE

NON-CONTACT
SIDE

D

8
Note : Spindle screw (DBA1252) of No.13 is the screw which applied special bond.
Therefore the adhesion becomes ineffective when takes it off once. Spindle screw is the part which cannot recycle.
13
When part #2 is replaced, part #13 also need to be replaced at the same time.

E

TRAVERSE MECHANISM ASSY-S PARTS LIST
Mark No.
>

F

Description

Mark No.

Part No.

1
2
NSP 3
NSP 4
NSP 5

05SD Pickup Assy-S
Spindle Motor N200
Guide Shaft VK1
Sub Guide Shaft VK1
Joint VK1B

OXX8014
DXM1197
DLA1940
DLA1941
DNK4272

NSP 6
7
NSP 8
9

Joint Spring VK1
Stepping Motor VK1
Mechanism Frame VK1
Precision Screw VK1

DBK1235
DXM1201
DNK4160
DBA1209

14

10
11
NSP 12
13

Description
Skew Screw VK1

Part No.
DBA1211

Skew Spring VK1
DBH1516
Stepping Screw
DBA1205
Spindle Screw VK1(for Service) DBA1252

XV-GX3
1

2

3

4

5

6

7

8

2.6 DECK MECHANISM ASSY
A

7
8

6
1

B

2

C

5
4

Cassette heads
Pinch rollers
Capstans
Cleaning paper
GED-008

3

NON-CONTACT
SIDE

CONTACT SIDE

D

E

DECK MECHANISM ASSY PARTS LIST
Mark No.

Description

Part No.

1
2
3
4
5

Main Belt
F/R Belt
Plate HD Blk
Roller Pinch Blk R
Roller Pinch Blk L

FF20B-13A
FF19S-31
F513-926
F514-133
F514-134

6
7
8

Clutch Assy Blk
Motor Main Blk
PCB Control Blk

F522-063
F525-394
F567-747

F

15

XV-GX3
5

6

7

8

1

2

3

4

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
A

JA8801

2ch Block Diagram

Compornent
OUT
Video OUT
JA8802

C

Y/C OUT
CN3001(2/2)
CN902(2/2)

6 10

8 12 14 16

6 10

8 12 14 16

DVD MODULE

VOLUME IC
IC3001
BD3401KS2

Video AMP
MM1623BF

B

CN3001
(1/2)

Back End IC
MT1389FE

FTS Driver
BD7995EFS

2ch DAC
PCM1753

25

B

16M
FLASH

61
59

Input SEL

3

4K
EEPROM

DVDM ASSY
9

CN901
CN1501

CN5701(1/2)

C

MIC MIX
Vocal Fader

63

25

CN902
(1/2)
64M
SDRAM

MAIN ASSY

FM/AM
TUNER
UNIT

9

6
10

54
10

CN5701(2/2)

4

RDS 65
IC5701
BU1924F

7

LINE IN

9

J3001

LINE OUT

DECK BLOCK

D
PB/REC
HEAD

PB

3

CN2301

ALC

15

Q2301

ERASE
HEAD

1
58

CN2302
RECOUT1

RDSDATA

Bias OSC
BIAS

E

JA3901

E

MIC ASSY
IC3901 (2/2)
BA4560RF

IC3901 (1/2)
BA4560RF
2
1

5
6

3

7

CN3901
MIC ECHO
9 IC3921 8
M65855FP

4

2

CN3051

JA3902

F
MIC BLOCK

16

XV-GX3
1

2

3

4

5

6

7

8

A

39 38

Power AMP Block
MAIN VOL
Bass

Middle

IC3031
BA4560RF

BASS Boost

Treble

3

33

B

Power AMP
IC3301 STK433-070

1

11

JA3992

4

14

7

JA3301

5

Godzzila AMP
IC3521,3522
LEVEL Detect
Circuit
(STBY)

SP OUT

MUTE

Volum JOG
S5971

94

CN5651 CN5901

70
96
97

18
19
40

C

MS Circuit

20

14

4

73

15

3

Blue LED

CPU
IC5501
PDC-129A-K
PDC-129A8-K

D5981
18
19

12
13

5
6

26

1

15

I

I

I

D

D5982
KEY

28

65
86

4 95

3

17

S5961-S5970

7

D

8

DISPLAY ASSY

10
7-9

Remocon
IC5902
RPM7140
-H9

FL Drider
IC5901
PT6315 14 31 34
I

I

FL
V5901

I

29 32 42

E

Power Supply Block

F

17

XV-GX3
5

6

7

8

1

2

3

4

3.2 OVERALL WIRING CONNECTION DIAGRAM and LOAB ASSY

2

LOAD+

1

SW2
V+3D

4

4

6

6

3

SW1

CN601

STEPPING
MOTOR

B

A3
A2
A1
H1+
H1SPINDLE H2+
MOTOR H2H3+
H3GNDS
V+5S
INSIDE

1

1

LOAD-

2

2

LOAD+

3

3

SW2

4

4

V+3D

5

5

CN902

9
10
11
12

SW1

CN103
AKN7035
1

1

ST1-

2

2

ST1+

3

3

ST2+

4

4

ST2-

12

12

10

10

8

8

9

7

7
6

6

5

5
4

4

2

2

3

3

1

14
15

1

23

23
22

22

20

20

21

21

19

19
18

16

16

17

12
11
10

15
ADD7418

14

24P FFC

PICKUP ASSY

18
17

14
13
12
11
10

9

9
8

8

6

6

4

4

7

7

5

5

3

3
2

1

2
1

10
11
12
13
14
15

16

16

18

18

20

20

22

22

24

24

17
19

A3
A2
A1
H1+
H1H2+
H2- RKN1053
H3+
H3GNDS
V+5S
INSIDE

21

21

23

23
25
27

1
2

CN901

5

VKN1285

FOCS RTN
FOCS DRV
TRKG RTN
TRKG DRV
VSHF
GND
LD(650)
PD
LD(780)
GND
MPD(780)
MD
MPD(650)
VREF(2.1V)
B2
B1
A
OEICG
C
780/650
B4
B3
VCC
GND

NC

3
4
6

7
8
9
10
11
12
13
14

4
5
6
7
8
9
10
11
12
13
14
15

15
16

16

18

18

20

20

22

22

24

24

17

17
19

19

21

21

23

23
25

25

SY
GNDD
CY/G
GNDD
Cb/B
GNDD
Cr/R
GNDD
G
GNDD
B
GNDD
R

1
2

3

CN3001

27

26

26

CN102

P/XI
SQUEEZE
VSEL2
VSEL1
ASPECT
SC
GNDD
VKN1258
V
GNDD

GNDD
GNDA
FL
GNDA
FR

25

ADD7520 (25P FFC)

24

9

19

VKN1482

24

7
8

17

ASSY
B DVDM
(AWM7966)

11

9

13

8

13

11

15

7

VKN1526

CN101

CN1013

5

5

CN104
S5B-PH-SM3

S5B-PH-K-S

C

2

3

LOAB ASSY
(VWG2346)
CN602 LOAD-

FOCS RTN
FOCS DRV
TRKG RTN
TRKG DRV
VSHF
GND
LD(650)
PD
LD(780)
GND
MPD(780)
MD
MPD(650)
VREF(2.1V)
B2
B1
A
OEICG
C
780/650
B4
B3
VCC
GND

2

ADD7521 (27P FFC)

LOADING
MOTOR
ASSY
: VXX2912

1

1

A

A

TRKUP
DVDMUTE
VDET
GNDD
GNDD
DVDACK
MDATA
SDATA
SCLK
XREADY

CN1501
VKN1285

XDVDRST
DVDPOWER
GNDD
GNDD
DOUT(AC3)
GNDD
GNDD
GNDM
GNDM
VPR+8(M)
VPR+8(M)
VPR+8
VPR+8
VDVD+12

D

DECK MECHA
(XYM3019)

3
4
5
6
7
8
9
10
11

52045-1145

CN5651
52045-1745

B4B-PH-K-S

1

(2P+4P)
ADE7118

YK56R-AA4N3

CN2901

CN2301

NoAssign7

E

GNDM
SOL
N.C.
PULSE
HALF
MODE
GNDM
VD+5V
RECF
MOTOR
RECR

1

3
2

2

VFDP
FLDC+
FLDCVE+5
REMOCON
GNDFL
VFL+5
GNDU
KEY1
KEY2
JOG
LED1
VLED+12
GNDLED

(11P FFC)

ADD7523

1
2

FLDATA
FLCK
FLCS

NoAssign5

5
4

7
6

9
8

11
10

13

15
14

12

17
16

3

ADD7410

4

(17P FFC)

CN2302

NoAssign1

B2B-PH-K-S

1

2
1

2

4
3

6
5

8
7

12

10
9

11

14
13

16
15

CN5901
52045-1745
NoAssign6

1
2

(11P FFC)
ADD7523

FM/AM
TUNER UNIT
(AXX7173)

F

3
4
5
6
7
8
9
10

* No schematic diagram

11

ASSY
D DISPLAY
(AWU8275)

GND
RDS
VSM
TXR
+9V
TXL
GND
DO
CLK
DI
CE

CN5701

(FL,LED,KEY,IR)

52045-1145

A
18

XV-GX3
1

2

3

4

17

5

6

VOLTAGE

7

8

A

SELECTOR
AC CORD
VNE1948
2

AN1

S102
AKX7017

JA8801

XKP3084

VKB1168

Cr

1
3

Cb

4

Y

2
6

V

5

MAIN ASSY C 1/4 - C 4/4
(AWM8013) (AWM8015)
(AWM8016)

JA8802
AKP7045

1

S-VIDEO OUT

C

3

Model

XV-GX3

S

/MTXJ

/DDXJ/RB

Singapore
Malaysia
Taiwan
Philippines
Indonesia

Mexico
Middle &
South
America

Thailand

South Africa
Middle East

MAIN ASSY

AWM8013

AWM8013

AWM8015

AWM8016

SUB ASSY

AWM8014

AWM8014

AWM8014

AWM8014

DISPLAY ASSY

AWU8275

AWU8275

AWU8275

AWU8275

MIC ASSY

2

/DDXJ/RD

4

/DFLXJ

B
VIDEO OUT

1
S101
AKX7017

COMPONENT+COMPOSITE OUT

240/220-230/110-120

JA3001

AWU8276

AWU8276

AWU8276

AWU8276

FU1

REK1028

REK1028

REK1025

REK1028

FU2,3

REK1025

REK1025

FU4

REK1029

REK1029

REK1029

REK1029

Main Trans(T1)

ATS7406

ATS7406

ATS7406

ATS7406

REK1025

C

AKB7170

6

L

1

R

3

LINE IN

5

L LINE OUT

4

R

2

JA3992
AKB1233
1

L
MATRIX

D

SURROUND
2

R

GNDHP
GNDHP

HPR

AMPR

3

4

5

6

8

9

2

4
3

11

2

12

1

E

1

2

3

4

5

6

7

8

9

10

11

12

XXM3009
DC FAN MOTOR

5

CN3901
52044-0545

J3992
51048-1200

JA3901 JA3902
AKN7003

10

R

J3992
D20PYY1215E

ADD7522
(5P FFC)

1

7

XKE3020
L
SP OUT

CN3651

5
4

JA3301

KM200SA2

SPR

HPL

2

SPR

AMPL

1

AMPR

AMPL

3
2

52147-1210

SPL

1

CN3991
SPL

52045-0545

+
+

CN3051

GNDA
MIC
VA+12V
ECHOCONT
MICSW

3

RKN1004

E

MIC ASSY
(AWU8276)
JA3991
AKN7003

÷ When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or
"PCB PARTS LIST".
÷ The > mark found on some component parts indicates the importance of the safety factor
of the part. Therefore, when replacing, be sure to use parts of identical designation.
÷
: The power supply is shown with the marked box.

19

XV-GX3
5

6

F

7

8

1

2

3

4

3.3 DVDM ASSY (1/2)

PICKUP ASSY CN1013

A

B

LD Driver for CD
(RF)

(RF)

(T)
(T)
(F)
(F)

LD Driver for DVD

SPINDLE MOTOR

C

FTS DRIVER

(T)

AKN7035

(S)
(S)
(S)
(S)

1

S5B-PH-SM3

(F)
(F)

(S)
(S)
(S)
(S)

(F)
(T)

(T)
(T)

A

CN601

STEPPING
MOTOR

(F)

D

3

2

E
(RF)
(D)
(F)
(T)
(S)
(C/V)
(R/Cr)
(G/Y)
(B/Cb)

F

(S_Y)

BA1/2

(S_C)

: RF SIGNAL ROUTE
: AUDIO SIGNAL ROUTE(DIGITAL)
: FOCUS SERVO LOOP LINE
: TRACKING SERVO LOOP LINE
: STEPPING SERVO LOOP LINE
: VIDEO SIGNAL ROUTE
: VIDEO SIGNAL ROUTE(R/Cr)
: VIDEO SIGNAL ROUTE(G/Y)
: VIDEO SIGNAL ROUTE(B/Cb)
: S VIDEO SIGNAL ROUTE
: S VIDEO SIGNAL ROUTE

20

XV-GX3
1

2

3

4

5

6

7

8

B 1/2 DVDM ASSY

A

(AWM7966)

B 2/2

(G/Y)

(S_C)

B

(C/V)

(B/Cb)

(D)

(R/Cr)

(S_Y)

B 2/2

!

C

D

E

B 2/2
F

B 1/2
21

XV-GX3
5

6

7

8

1

2

3

4

3.4 DVDM ASSY (2/2)
A

B 2/2 DVDM ASSY
(AWM7966)

(D)

B 1/2

B

B 1/2

C

D

E

B 1/2

F

BA2/2
22

XV-GX3
1

2

3

4

5

6

7

8

A

3V Regulator

1.8V Regulator

5V Regulator

C 1/4 CN1501

(D)

6.5V Regulator

7.8V

B

7.8V

5.0V
6.4V

C

NC

Video Driver Amp

(S_C)

(S_C)

(C/V)
(S_Y)

(C/V)

(G/Y)

(B/Cb)
(R/Cr)

G

(B/Cb)

B

(R/Cr)

R

NC

NC

C 2/4 CN3001

(S_Y)

(G/Y)

D

NC

FL

FR

E

(D)
(C/V)
(R/Cr)
(G/Y)
(B/Cb)
(S_Y)
(S_C)

: AUDIO SIGNAL ROUTE
: VIDEO SIGNAL ROUTE
: VIDEO SIGNAL ROUTE(R/Cr)
: VIDEO SIGNAL ROUTE(G/Y)

F

: VIDEO SIGNAL ROUTE(B/Cb)
: S VIDEO SIGNAL ROUTE

BA2/2

: S VIDEO SIGNAL ROUTE

23

XV-GX3
5

6

7

8

1

2

3

4

3.5 MAIN ASSY (1/4)
MAIN ASSY
(AWM8013 : DFLXJ, DDXJ/RD)
(AWM8015 : MTXJ) (AWM8016 : DDXJ/RB)
VE+5

AWM8016
DDXJ/RB
STBY
STBY
STBY
39k
22k

R5583
10K
2

2

1

SUBAC

1

C5581
1/50

R5581
2
10K

2

C5582
100p 1
CH

DVDACK

SIMUKE

TXIDATA

MODEL

RDSDATA
RDSPOW

VDET
KEY1

NC

KEY2

TXODATA
TXCLK

JOG

TCRECR

LEVELIN
XPROTECT

TCRECF

SDATA

TCMODE

MDATA

TCHALF

SCLK

28.FLCLK
29.(DTS ON/OFF)STBY
30.XREADY

FLCE

52.TXCE

VSS2

51.EPROM_CLK

VDD2

FLDATA

EPROM_I

EPROM_O

EPROMCS

NC

NC

ECHOCONT2

ECHOCONT1

UTEST

NC

220

R5556
R5555
R5554
R5553

220
220
STBY
STBY

R5552
R5551
R5550
R5549
R5548
R5547

220
220
220
220
220
220

62
61
60
59
58
57

20

R5545
10k

R5543

R5542

52

220

220

51

220
220
220

48
49
50

45

23
22

25
24

C1507
STBY

C1502
0.1
21

19
18

R5546
10k

R5539
R5540
R5541

R5537
R5538
17
16

VE+5
UTEST
STEST

C1506
47/25
C1503
0.1

15
14

R5544
12k

VPR+8

1000/16

C1501
0.1
13
12

C 3/4

VDVD+12

VPR+8M

C1505
11
10

4.7K
8.2k

STBY
C5506

32

RELAY

DVDPOWER
GNDD
GNDD
DOUT(AC3)
GNDD
GNDD
GNDM
GNDM
VPR+8(M)
VPR+8(M)
VPR+8
VPR+8
VDVD+12

9
8

XDVDRST

7
6

VDET
GNDD
GNDD
DVDACK
MDATA
SDATA
SCLK
XREADY

TRKUP

5
4

C 1/4

SHORT for
TEST POINT

GNDD

STBY*2

GNDVDM

PCB Binder
VEF1040

B 2/2 CN901

24

XV-GX3
1

70
18
68
67
66
65
64

U-COM

VDD1

94

R5558

C5507
STBY

PB/XREC

MOTOR

(RECMUTE)

SOL

BIAS

BEATCUT

NC

VSS3

VDD3

FLASH E/D

FLASH DO

FLASH CLK

XDVDRST

XSYSMUTE

TCPULSE

1

67
24
23
25
30
93

17
3
2
NC(DVDMUTE)

CN1501

VKN1256

1

NC

CNB25

PB/XREC

BIAS
85
84
83

R5567
R5566

R5563
R5568

220
220
220
220

STBY
C5508

94
93
92
91
90

KEY1

CF2

C5589
1/50

R5589
220k
GNDU

F

C5588
0.1 1
C5584
STBY

1
VOLCLK

SYSPOW

NC

NC

NC
CF1

74
LED1
R5559
220

50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31

C 3/4

E

R5586
120k

NC
TCMSIN

VSS1

D5502

D5501
1SS355

LEVEL

NC

PDC129A-K
PDC129A8-K

XT2

STEST

R5535

XT1

LED1

(ATT6dB)STBY

220

VE+5

IC5501

XRESET

NC

R5525
R5526
R5527
R5528
R5529
R5530

NC
LED2

VDD4

220
220
220
220
220
220

NC

REMOCON

VSS4

30

R5514
R5522

80.(XPBMUTE)
79.NC
78.NC

REMOCON

NC

220
220

NC

ACPULSE

RDSCLK

NC

R5512
R5513

MIC DET

NC

220
220

(HPDET)

XRECMUTE

R5511
100

X5501
ASS7034 10MHz

C5510
0.01

C5509
0.01

CH

GNDU

R5503

R5509
C5503 STBY
STBY

22
23
24
25
26
27
28

R5532
STBY

470

DVDON/OFF

NC

STBY

17
18
19
20

R5531
1M

R5502

R5510
STBY

R5516
10K

R5515
10K

R5517
R5519

0.01
C5504
R5521
1M

1k

R5508
STBY

C5502

X5502
VSS1197
STBY

VE+5

R5501

R5505
STBY
220
R5506

6

D

2
R5565

R5504
100K

3

7

48
51
49
50
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51

C 3/4, 4/4

220

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

1

C5505
100p

2

81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100

22

R5564

GNDU

XPROTECT

*

R5580
1K
2

1
1

GNDU
C5501
0.1

7

*

2
1

2
1

5

VE+5

C

C5583
10/50

R5572
15k

4

CNB07

B
E DTC143EUA

NC

6

W229

RELAY

GNDU
NC

3

Q5503
2SC4081(QR)
BR5582
1
2
1K
E

C

97
220
96
220SYSPOW

2

1
2

C Q5502

0.01

FLASH DO
FLASH CLK
XRESET
VE+5

C5585

1

FLASH E/D

B

RDS

1

2

R5585
2 2.2K 1

STBY

90
91
92

2

1
C5587
0.01

RESET

R5507
STBY(220)

VE+5

CN5501
(HLEM7S-1)

65

L5501
22u

RESET

FLASH U_P

AC PULSE

VU+5

C5586
100/10

for
SIMUKE

R5505
R5553
R5554
R5517
R5519

AWM8015
MTXJ
STBY
STBY
STBY
47k
STBY

VOLDATA/CE

for
RDS

AWM8013
DDXJ/RD,DFLXJ
STBY
STBY
STBY
STBY
47k

NC

*

R5584
1 47k 2

C 1/4

A

2

3

4

6

7

8

FM/AM TUNER UNIT

CN5701
52045-1145

VA+9

11

GND
10

9
R5705

8
7
R5703
STBY

R5704
STBY

STBY

C5704

STBY

C5713
STBY
FLDC+

GNDA

LED1
20
19
18
7
26
28
27

5

47k

7
VLED+12

Vcc 8
NC 7
TEST 6
GND 5

8

VFL+5

9

0.1

CS
SK
DI
DO

C5401

R5401

4
6

11
13

KN3
VNF1084

R5402
47k

C5402
47p CH

1
2
3
4

15

R5653

Q5411
DTA143EUA

10

MUTE

C

17

C5411
22/50

B

47k

MUTE
R5411
560

R5412

E

VD+5

3
GNDA

BACKUP

C 3/4

GNDU

GNDD

CN5651

1

VE+5

B

C 4/4
2

IC5401
S-93C46BD0I-J8T1
Main:
Sub:BR93L46RFJ-W

A

52045-1745
FLDATA
FLCK
FLCS

VFDP
FLDC+
FLDCVE+5
REMOCON
GNDFL

10 VFL+5
GNDU
12 KEY1
KEY2
14 JOG
LED1
16 VLED+12
GNDLED

CN5901

STBY

C5723

1000p
C5705

FLDC-

STBY

6

64

STBY

STBY
C5702

STBY

R5707
STBY
R5708
STBY

GNDS(PJ)
STBY

C5701
VE+5

STBY
C5711

GNDD

61
62
52

GNDX

C5710

STBY

TXL
GND
DO
CLK
DI
CE

66

R5713
STBY

C5712

T1

C5703
STBY

T2

CMP

2
1

27p CH

1000p

VSS3

3

C5708

VSS2

4

(TXL)

560p
CH

VSS1

6
5

C5716

C5709
0.01

XI

VDD2

STBY

XO

IC5701
BU1924F

C5707

VDD1

C5706
0.1

RDS

STBY

C5720

VREF

R5714

GNDD

NC

C5718

CH

R5706
STBY

270p

10/50

RDSDATA

15 X5701
14
13
12
11
10
9

47/16

C5721
C5719

C5715
27p CH

ASS7004
RDSCLK 16

QUAL

C5717
0.01

1
2
3
4
5
6
7
8

C5722

100

RDS
VSM
TXR
+9V

D

STBY

C5714
STBY

RDS

RDS

VD+5

R5715
220k

5

C

GNDU
GNDFL
GNDLED

GNDS

VFDP
(TXL)

TX_LCH

CN2901
52045-1145

TX_RCH

1

(TXR)

2

R2902
47k
R2903
47k
R2904
47k

VD+5

3
4

R2901
47k

5
6
7
8
9
R2912 Q2906
1 2SB1132(RS)

GNDTCM

C2
GNDM
E2

GNDD

C 2/4, 4/4

83

84

68

57

58

59

R2911
47k

Q2902
RN1901
B2

11

D

1SS133

E

60

47k

R2906

C

B

1k(1/4W)

C
1
D2901 R2910

Q2902
RN1901
R2909

C

1k(1/4W)

R2907
1k(1/4W)

B

R2908

C

E

E
B

1SS133

E
B

10
2SB1132(RS)
Q2905

D2902

Q2901
DTA124EUA

R2905
47k

VM+12

GNDM
SOL
N.C.
PULSE
HALF
MODE
GNDM
VD+5V
RECF
MOTOR
RECR

DECK MECHA

C 2/4

VD+5

CNB11

VA-12

E

U-COM

NOTES
ALL CAPACITORS ARE IN µF
UNLESS OTHERWISE SPECIFIED
CH:CCSRCH***
OTHER:CKSRYB***
TS:CE*****M##-TS
AL:CEAL***M##-*
(OTHER : CEAT***M##)
ALL INDUCTORS ARE IN µH
UNLESS OTHERWISE SPECIFIED
LAU***J
ALL RESISTORS ARE IN
UNLESS OTHERWISE SPECIFIED
:1/4WPU
:1/16W
NoAssign1
NoAssign2
(1/2W): RD1/2PM***J

F

C 1/4
25

XV-GX3
5

6

7

8

1

2

3

4

VKB1168

R8875

R8876
STBY

R8865

R8866
STBY

C8872
STBY

R8855

47p CH

C8862
STBY

R8856
STBY

21

19

17

15

13

9

11

7

C8852
STBY

22

20

18

16

14

12

10

8

VIDEO OUT

Y1out

C8831

1
1

2 1
2
R1503 R1504
22k
22k

R3004

VA-12

C3004

1.8k

C3107

10/50

C3105
STBY

10/50

C3106
STBY

47k

B

R3103
22K

C3101
220p

L

R3007

4.7K
B2

R3101
5

10/50

4.7K
R3006

E

E2
Q3001
(2/2)
IMX9
C2

15k

C3003

R3104
22K

R

R3005

B

Q3003
DTA124EUA
C
E

C3103
STBY

3

470p
R3002

1

LINE OUT

220k

L

C3002

6

Q3001
(1/2)
IMX9

1.8k

C3104
STBY

220k

470p
R3001

C3001

C

2

C3102
220p

4

LINE IN

R

R3102

C3108
10/50

15k
GNDA

3

1SS133

C2306

GNDA

3
S

1D

R2821
11k
C2813

VR2801
PCP1032
100k-B

M
4700p

B

C

Q2801
2SC1815(YGR)

4700p
M
C2803
10k

C
Q2802
2SC1815(YGR)

C2814

220p
L2812

M
1500p
R2822
11k

VB+12

22k
STBY

R2824 C2816
1k

1/50

ALL CAPACITORS ARE IN µF
UNLESS OTHERWISE SPECIFIED
CH:CCSRCH***
YF:CKSRYF***
OTHER:CKSRYB***

(1/2W)

B R2811

R2809
47/25

C2807
47k

1k

R2810

Q2805 E
2SC1815(YGR)

BIAS

1k

33/50

C2810

4.7k
R2816

1k
GNDB

85

26

1/50

NOTES

R2805
VM 160
(1/2W)

VM 4.7
R2803

B

1k

E
B

C
R2815

C2812

RTF1004
10mH

E

L2802
LFEA151J
0.15mH

33/50

C
E

C 2/4

L2801
RTD1082

C2805

Q2806
2SC2240(GR)

1
2
3

(2125)
ACG7058- -T

150p/200
C2809

F

M
0.012
C2801

HA
8200p/100
C2808

6
5
4

M
C2804
10k 6800p

BIAS OFFSET

R2802 C2802 R2801

VR2802
PCP1032
100k-B

BIAS OSC.

GNDA

R2823 C2815

M
1500p

CH 220p

105KHz

Q2352
RN1901
E2

GNDA

VA-12

10mH
C2811

10/50

CH

STBY

R2352
E

L2811
RTF1004

C2

B2
B

32

B
C DTC114TK

1k

R2813

1k
R2814

R2804

Q2352
C RN1901
100k

R2351

D2305

R2303
330k

D2307

Q2302 2SK373(YGR)

E

B

C

STBY

PB/XREC

D2302
1SS133

Q2351 E
DTA124EUA

E Q2304

1M 2
G
R2302
10p
CH

C2302

2

STBY
Q2303
C DTC114TK
B

R2304
330k

1

VA+12
10/50

E

D2306
1SS133

CN2302
B2B-PH-K-S

C2305

C2304
820p

Rch

10p
R2301 G
1M 2

1
YK56R-AA4N3

1SS133

GNDA

C2301
CH

D2301

Lch

2

1SS133

3

D2303
1SS133

D

D2304
1SS133

DECK MECHA

4

2SK373(YGR)

S

1D

Q2301

B4B-PH-K-S

C2303
820p

CN2301

M:CQMA***
HA:CQHA***
MB:CQMBA***
TS:CE*****M##-TS
JQ:CEJQ***M##-*
AL:CEAL***M##-*
(OTHER : CEAT***M##)

XV-GX3
1

2

3

4

2

CH CH
C1509 C1510
270p 270p

RECAC
VE+5

C 3/4

R3003

JA3001
AKB7170

(C)

75 1%

GNDD

2 R1501
5.6k

Cout

R8842

STBY

R1502
5.6k

(Y)

1000/6.3

1%

1

STBY

R8822

R8832
75

1000/6.3

STBY

R8835

STBY
F8841

STBY

F8831

4

2

3

1

S-VIDEO OUT

AKP7045

Vout

C8881

1% R8821
75

STBY CH 47p
C8832

C8842 C8822

STBY

JA8802

C

6

C8851
1000/6.3

5

L8821

B

(Y)

5

6

V

1%R8853
75

3

L8851
STBY

(Cb)

C8861
470/6.3

4

2

1% R8863
75

2

L8861
STBY

1

Y

4

VKN1258

3

Cb

47p CH 47p CH

STBY

1

FR
27
GNDA 26
FL
25
GNDA 24
GNDD
23

Cr

B 2/2 CN902

(Cr)

R
GNDD
B
GNDD
G
GNDD
Cr/R
GNDD
Cb/B
GNDD
CY/G
GNDD
SY

C8871
1% R8873
75
470/6.3

L8871

CN3001

Video out

JA8801
GNDD
V
GNDD
SC
ASPECT
VSEL1
VSEL2
SQUEEZE
P/XI

A

COMPONENT+COMPOSITE OUT

3.6 MAIN ASSY (2/4)

5

6

7

8

MAIN ASSY
(AWM8013 : DFLXJ, DDXJ/RD)
(AWM8015 : MTXJ) (AWM8016 : DDXJ/RB)
VA+12

VA+12

CN3051
52045-0545
1

W288
R2401
220K
470K

R2404 R2402
470K 220K
R2403

VR2401

4.7K

R2409

4.7K

STBY

C3037

STBY

C3038

C 3/4
97
96

220

GNDA

GNDD

D

R2405
STBY

R2406
STBY
68K

VR2402

R2410

33K
C2321 6800p MB

R2323 R2321 470K

R2327 R2325
STBY 0
R2311 680 R2353
0
R2408

0
R2328

C2106
0.33
C3027
470p

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
C2322 MB
R2324 6800p
R2322 470K
33K

C

GNDA

R2407
68K

C3030
STBY
R3030
0

48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33

MNF2
MOUT2
MOUT1
MNF1
BNF1
BOUT1
BOUT2
BNF2
AMSOUT
TONEOUT2
VIN2
TONEOUT1
BBIN1
VIN1
BBNF1
VOLOUT1

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

C3046
10/50
R3029
0

0.01

C3029
STBY

C2101

R2326

4

REC LEVEL Adj.

STBY
10/50
C2409

STBY

IC3031
BA4560RF

220

C3019
4.7/50

220p
C2407

10/50
C2410

10K

+

1k
R2107

D1
D2
E1
E2
PBNF2
PBOUT2
PBOUT1
PBNF1
TAPEA1
TAPEA2
TAPEB1
TAPEB2
RECNF2
RECOUT2
RECOUT1
RECNF1

ROUT

1000p
C3022
47/25
C3021

R2312 680

8
7

5

220p
C2405

R2354
0

-

VA+9 VD+5

12k
6

0.1
0.1
C3026 C3025

R3012

R3011
4.7M

220p

C2408

3.3/50
C2325

VR2301

VA+12

VA-12
R3013

STBY
C3018

220p
C2406

R2329

12k

64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49

-

CH

STBY
C2403

STBY
C2404

C2323
STBY

STBY

C2324

VR2302

B

GNDA

R3036

47/25
-T

0.033
MBC2401

MB
0.033
C2402

3.3/50

C2326

R2330
10K

+

180p

12k

R3032
180k

C3024

1

C3040
180p CH

10/50
-T

C3034
0.056

STBY
C3017

STBY
C3016

STBY
C3015

10/50
C3014
10/50
C3013

STBY
C3012
STBY
C3011

STBY

C3036
R3034
15k

GNDA

47/25
C3023

VOLOUT2
BBNF2
BBIN2
LF1
LF2
LF3
LF4
SWOUT
FILTER
1/2VCC
VCC
ALC
GND
VDD
SI
SC
ALC

C3032
0.056

R3037 R3038
15k
15k

R3033
180k

IC3031
BA4560RF LOUT

C3039

470p
C3020

IC3001
BD3401KS2

10/50

R3031
15k

3

4

5

GNDA
MIC
VA+12
ECHOCONT
MICSW

8
2
R3035
12k

C3035
R3039 R3040

10/50
10/50
10/50
10/50

STBY
D2102

C3055
C3056
C3059
C3060

10/50

70

270k

C3057

100k

10/50

C3058
STBY

R2109

0.056

C3054
0.33/50

VOL

R2108
STBY

33k
R2105

R3051
4.7k

TNF2
TNF1
SUR1
SURROUND
BASS/TRE
SUR2
LINEOUT2
LINEOUT1
SAOUT2
MIC MIX
SAOUT1
KARAOKE
CAP
MIC
A1
A2
INPUT
Buffer
B1
SEL
B2
C1
C2

4
C2105 D2101
10/50 1SS133

C2104 22/50
C2103
C3033
270
C3031
0.056
R2104 1k
R2106

1800p

0.068

C3043

0.1
C3049
1
C3047
1
C3048
0.1
C3050
C3051
2200p
C3052
2200p
C3053
1

3

3

Q2101
2SC4081

C3041
10/50
C3042
10k R2101

C2102

4.7K 0.068
R3042 C3044

4.7K
R3041

4.7K
R3043

4.7K
R3044

GNDU

3.9k

R2103
120k

R2102

C3045
10/50

L2101
STBY

2

E CN3901

C 1/4

U-COM

TX_LCH
TX_RCH

A

C 1/4

C 2/4

PB LEVEL Adj.

E

U-COM

ALL RESISTORS ARE IN
UNLESS OTHERWISE SPECIFIED
1/16W
1/4WPU
ALL COILS ARE IN µH
UNLESS OTHERWISE SPECIFIED
LAU***J

F

ALL DIODES ARE 1SS133
UNLESS OTHERWISE SPECIFIED
1SS133
MTZJ***
DZ

C 2/4
27

XV-GX3
5

6

7

8

1

2

3

4

3.7 MAIN ASSY (3/4)

Q3652 C2

E
100/25

1
47k

E

C
B

100k

100k
2100k
D3504
D3503
1
MTZJ36B MTZJ36B

100k

R3510

D3508
MTZJ18B
S

D

R3333
33k
R3334
1k
R3335
2.2k
S5688G

Q3305
2SC4081

STBY STBY

C3319 R3330

-T

GNDP
GNDS

W179

IC3304
STBY

GNDA
GNDP

GNDP GNDS

C 3/4

GNDS

28

XV-GX3
1

2

3

C3320
47/25

D3309
1SS133

2

D3308
1

2

D3306
S5688G

C3316
220/50

S5688G

1

2

1

D3304

C3318
0.22/50

2

C3317
0.22/50

B
E
1/10w

1/10w
R3364
2.2

1/10w
R3363
2.2

1/10w
R3362
2.2

R3361
2.2
2

1

5.6k

R3332

1

2W 0.22
R3322
2W 0.22
ACN7122
R3329

R3321
ACN7122

C3313 R3317
10/50 1.5k

R3326
47 MUF
(1/4W)
2 1
D3302
S5688G

1

C3315

R3318
1.5k
C3314
10/50 -T

2

GNDA

C

CH2 IN

CH2 NF

ST-BY

CH1 NF

CH1 IN

GND

SUB

+PRE

CH2-VE

CH2+VE

CH1-VE

CH1+VE

+VCC

-VCC

-PRE

2
1000p

C3307

56k

1
1

S5688G D3305 S5688G
S5688G

AEK7021 (7A)

CH

R3328
STBY
D3307

2

C3310
47p
CH

R3327
STBY
D3303
2

C3306
2.2/50

1R3314 2
220
R3325
MUF 47 D3301
(1/4W) S5688G

1

E

2

F

56k

220/50
-T

C

2

1k

C3309
47p

1

R3323
1

56k
R3320

R3319

CH C3311
8p CH

56k

2.2k
R3310

C

220

CAUTION : FOR CONTINUED PROTECTION AGAINST
RISK OF FIRE. REPLACE ONLY WITH
SAME TYPE NO. 491007 MFD, BY
LITTELFUSE INK. FOR IC3303.
W182
STBY
IC3303

R3509

D3507
MTZJ18B
R3505
R3506

15k

R3514
R3307 2
1
0

0

C3304
STBY

R33081
2
0

STBY

2 R3305 1

STBY

R3301
R3302

C 2/4

3D
Q3301
Q3303
STBY
S
2SD2114K(VW)
1
1
S
Q3304
Q3302 2SD2114K(VW)
STBY
R33122 B
3 D
1

E

8p
C3312

1 R3311 2
2.2k B

1

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

1

R

L,R POWER AMP

2

MUTE

VH-

R3313

1

2.2/50

2
G

1k

C3305
2.2/50

1

1

C3302

R

STBY
1
2
R3304

2

2

2

ROUT

G
2

R3309

1

GNDA

R3303
2
1
STBY

1

D3502
DAP202K

1

GNDA

VL-

R3321,R3322
:ACN7122-

2

1

E

LOUT

MTZJ10B
R3512
G
100

D3510
30PDA20-FC6
D3512

STBY

STBY CH2NF

C3303 1/50

2

2.2/50

L

1
2

R3522

2 R33061
0

C3301

1
2
R3504

B 1SS133
10k
D3506

C3308
1
2
1000p

4

+ 5

D3501
DAN202K

Q3502
1 2SK2232

R3315 2

- 6

10k

2

R3316 2

8

1
2

IC3301
STK433-070

STBY

- 2

C3521

8

1

+ 3

1
2

2

4

MUTE

L

15k

R3513

STBY

R3533

IC3522 STBY
STBY
CH2IN
R3521
STBY

2

4

VA-12
R3530
1

0.01

R3541
10K

Q3504

R3355
100k

STBY

8

3 +

C3522

7
IC3521
STBY

2 -

E
C

R3356
100k

C 1/4

C3528
STBY
2
1

1
IC3521
STBY

Q3521
STBY

C3541

R3503

2SC4081
2SA1576A

STBY
C3529

R3528
STBY
R3527
STBY

D

7
IC3522
STBY

1

4

STBY
C3523

C3524

STBY

R3524
STBY
R3523
C3525 STBY
1
2C3526
R3525
STBY STBY
STBY
1
2
R3526
STBY

5 +

R3542
100k

D3505
B 1SS133

E

E

R3543
22k

Q3503

1

C 1/4

8

D3542
UDZS7.5B

D3541
ISS355
2

RELAY

6 -

B

1
2

1

R3529 C
STBY

R3532
STBY

C
R3531
STBY

S

D
D3509
(SIGNAL CLIP DETECTOR)

MTZJ10B
R3511
G
100

1
2

C3527
2
STBY

GNDS

D3543
UDZS20B

R3546
4.7k

B

Q3542
2SC4081

2

C 4/4

VD+5

R3547
0

Q3501
2SJ304

1

GNDF

C 1/4

1 D3602
MTZJ7.5B
2

47k

R3544 R3545

VH+

30PDA20-FC6
D3511
2

LEVEL

(2/2)

VA-12

VL+

1

B2
Q3606
UMH1N
E2

Q3541 2SA1576A
C
E

22k

Godzilla Amp

C2

3.3k

VF-12

C 1/4, 4/4

B2
C2

R3656

GNDF

VA+12

VH(2/2)

2
D3605
1SS133

1

2

B
E

XPROTECT

C

Q3604
UMB1N
E2

2

VL/VH

VD+5

D3601 R3613
2 11
2
820
MTZJ7.5B

C3601

1

1

E2

R3617
2
10k

Q3606
UMH1N
(1/2)

C3653

R3655

B

D3654

1SS133

C

8.2k

E

D3604
1SS133 1

B

C

B2
Q3605
UMH1N
(2/2)

VA+12

C

Q3653
DTA124EUA
R3654

B

Q3604
UMB1N
(1/2)

RN1901 E

1SS133

D3651

B
1SS133
Q3654

2SD2144S(UV) D3653

C

RN1901 E2

Q3652 C

E

C3652
47/25

C

E

B

R3652 D3652 B
2.2k MTZJ3.9B

2
XPROTECT

C3602

Q3651
DTA124TK

33

R3651

FAN-

2

47/25

1

C3651

FAN+

VF+12

C2

B2
C2

VF+12

1
R3615
1k

B2

KM200SA2

CN3651

R3610
27k

E

E Q3605
UMH1N
(1/2)

1.8k

STBY

R3653

R3605
R3608 STBY

R3607
STBY

STBY

GNDD
Q3602
STBY

1

TO FAN

C

R3606 B

2

B

VD+5

D3603
R3614
R3612
21
2
10k
10k
1SS133

C

1

1k

2

B
C

VD+5

Q3603
UMB1N
E2 (2/2)

1

1/50

R3604

220

VH+

E

Q3603
UMB1N
(1/2)

C Q3601
2SC4081
E

R3602 B
R3603
1k

PROTECT

1
R3611
1k

TH3601
NCP18WF104J03RB

1/50
-T

A

R3616
2
10k

STBY

VD+5

4

5

6

7

8

MAIN ASSY

C 3/4 (AWM8013 : DFLXJ, DDXJ/RD)

A

(AWM8015 : MTXJ) (AWM8016 : DDXJ/RB)

CN3991
52147-1210
12

SPL

11

SPL

10

AMPL

9

AMPL

8

HPL

7

GNDHP

6

GNDHP

5

HPR

4

AMPR

3

AMPR

2

SPR

1

SPR

470

GNDSP

JA3992

L3301
ATH-059
R3345 100

C3997
STBY

0.022

4.7

1

NP
C3996
STBY

(1/2W)PMF
C3323 R3347 C3325
27k

R3343

Q3321
2SC4081(QR)

AKB1233

0.022
2
3

L3302
ATH-059
R3346 100

STBY

STBY
R3352 STBY
(1/10W)

C3331 C3329

R3342
33k

JA3301
1
2
3
4

D3323
DAN202K

+
+
-

5

L
6

SPOUT

R3341
33k

XCG3008
C3328
0.01

STBY

0.022

STBY
R3351 STBY
(1/10W)

R3349 STBY
(1/10W)

4.7

27k

0.022

R3350 STBY
(1/10W)

C3327
XCG3008
0.01

(1/2W)PMF
C3324 R3348 C3326

R3344

1.8k

0.1

2SC4081(QR)
Q3322

R3340

(R)

C

(L)

C3332 C3330

R3338
ACN7112(2W)

MATRIX SURROUND

0.1
1.8k

R3339

(L)

3W LMF

B

E

R3992
470

R3337
ACN7112(2W)

3W LMF

J3922

R3991

D

R

XKE3020-

D3321
DAP202K
E

C

GNDS

GNDHP

2

C 1/4, 4/4

C
B

Q3629
DTC143EUA

R3630
10k

E

C3624
10/50

Q3628
DTC124EUA

XPROTECT

C 2/4
C 4/4

E

C
R3629
27k

R3628
STBY

D3627
STBY

1
E

Q3625
HN1C01FU(YGR)

2

1

C
B

C3623
470/6.3

1SS133 1SS133

2.2/100

R3625
2.7k
C3622
2

1

2

1

D3621
MTZJ5.1B

LOUT

R3621
22k
2
1
R3622
122k 2

D3626

E2

D3625

E

B
C
Q3623
Q3620 B
DTA124EUA DTA124EUA

W398

Q3625
HN1C01FU(YGR)

R3626
13.3k2

1
2

E
Q3624
STBY
C

B
E

R3627
STBY
0

C2

D3622
DAN202K

2SC4081(QR)
Q3622
D3624
1SS133

R3623
6.8k

B2

ROUT

VD+5

1
2

GNDC

C3621
STBY
R3624
STBY

VH+

D3623
1SS133 B

Q3621
DTA124EUA

GNDSP

RECAC

AC1

F

C 3/4
29

XV-GX3
5

6

7

8

1

2

3

4

3.8 MAIN ASSY (4/4)
MAIN ASSY
(AWM8013 : DFLXJ, DDXJ/RD)
(AWM8015 : MTXJ) (AWM8016 : DDXJ/RB)

C 4/4

PRIMARY PART

FU3
H3

H5

H6

CN2
B4P7S-VH

W446
W134

W372
W447

4

1

3

2

2

3

1

4

0

VFDP

2

BHAC1

3

GND

4

BHAC2

5

BLAC1

6

BLAC2

7 SUBAC1
0

8 SUBAC2
120

W338

W337

3 2 1

W373

9

120

FLAC1

10 FLAC2

4

8 7 6 5

AKX7017

10

1

2

1

1

2

0

CN1

EXCEPT
/MTXJ

0

0

0

*2

*1

FUSE01

W441

W440

3 2 1

8 7 6 5

4

S101 AKX7017

FU2
H4

120

W133

S102

B2P3S-VH
W374

VOLTAGE SELECTOR

ATS7406

EXCEPT /MTXJ
H3-H6:AKR7001

W439

B

T1

W438

240/220-230/110-120

W411
W412

W375

A

/DDXJ/RB
/DDXJ/RD
/DFLXJ

W333

W370

W365
H2 W366

1

NC NC
NC

FU4
REK1029
REK1029
REK1029
REK1029

230V 230V 100V 120V

FU3
REK1025
REK1025
REK1025

115V

0V
FU2
REK1025
REK1025
REK1025

0V

FU1
REK1028
REK1025
REK1028
REK1028

4

/DFLXJ
/DDXJ/RD
/MTXJ
/DDXJ/RB

0V

50/60Hz
110V-127V
220V-230V
240V

2

W131
NC

C3
STBY

NC

L1
STBY

ACE7013 W367
W404

NC NC

1

W132

3

NEUTRAL

H1

0V

2

0.01
C1

LIVE

E

ATT7080
ATT7078

5
6
7
8
9

T2

EXCEPT /MTXJ
ONLY /MTXJ

VE+5

VUN+5

13.5V

IC11
TA7805S

C15

R14
1k

C14
0.01

C12

Q12
2SD1858X(QR)

C 1/4

R15
10k

D13
DAN217

C11
1000/25

R11 2.2k

+
~

D14
1SS133

2

22k

~
-

R12

39

S1NB60

ASR7027

1

D11

RY1

R16

D12

Q11
2SC4081(QR)

GNDD

F

SYSPOW
SUBAC

• NOTE FOR FUSE REPLACEMENT
CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE.
REPLACE WITH SAME TYPE AND RATINGS OF FUSE.

C 4/4
30

XV-GX3
1

2

3

10/50

1000p

1/50

VNE1948-

MTZJ20B

KN1

C13

PROTECT BAIDEN

4

U-COM

H1,H2:AKR7001
FU1

XKP3084

C5
ACG7033

AN1

RY1
ASR7027

W371

D

/MTXJ

W365
W366
W367
W404
W370
W371
W132
W131
W306
W307
W374
W375
W133
W134
W411
W412
W372
W373
W446
W447
W440
W441
W337
W338
W438
W439
W334
W333

U-COM

W334

W307

W306

C

5

6

7

8

AC1

C24 STBY

+

~

C25

C26

B10PS-VH

2200/63

STBY
C22

~

C21

STBY STBY

~

VA+9

B

47/25
C74

0.1
C73

C71

STBY

1/50

D62
STBY

C65

STBY

C72

B
10

R62
C63

C64

GNDB

GNDTCM

D61

22/50

STBY

1/50

STBY

GNDF GNDC

GNDP

GNDM

C61

H7 FU4 H8

GNDS

C36
XCG3008VUN+8

H7,H8:AKR7001

C62

VUNVFDP

C35
XCG3008-

~

VLED+12

IC61
TA7812S
IN
OUT

+

-

VA+12

VA+9
IC71
NJM78M09DL1A-TLB
IN
OUT

VL+
GNDREG

VUN+8
Q41
2SB1565(EF)

220

R41

C

IC41
NJM78M05DL1A-TLB
IN
OUT

IC42
NJM78L08A
IN
OUT
C47

C44

1/50

GNDU
GLED
GNDM

VFL+5

VPR+8M

47/25

GNDD

VD+5

VPR+8
VPR+8

D44
MTZJ11B

47/25

C41

D41
D5SBA20(B)

6800/25

~

C42
0.047

-

D43
MTZJ7.5C

C 3/4

D53
MTZJ27B

GNDF

R58 1

Q51
2SB1565(EF)

IN

R57 1

10/50
D57
MTZJ15C

C57

C56
0.047/50

R51 PMF C53
3.3k
33/50
(1/2W)
D55
1SS133
C54
22/50

GNDSP

D
GNDA

OUT

IC51
TA79012S
VA-12

VFDP

VF-12

C 1/4, 3/4

VL-

XPROTECT
R55

82k

R56

220k

E
DTC124EUA
Q52
C B
B

DTA124EUA
Q53

C

E

E
GNDS
D81

C 1/4

-T

FLDC+

R81
10k

S5688G
C81
1000/10

VA-12
MTZJ3R6(B)
D82

R82
C82
0.22

FLDC-

3.3k

D83

MTZJ2.0B

1
Q81
2SB1565(EF)

R84

10

D52
S5688G

~

VDVD+12

C32

9

D51
S5688G

4700/35

8

C51

7

-T 100/63

6

XCG3008C33

4700/35
C31

5

D31
D5SBA20(B)
C34
XCG3008-

R61

4

47k

VL+

C

3

VM+12 VB+12 VF+12
Q61
VA+12
2SD2012

VL+

C33 ~ C36
:DFL ONLY

10/50

VH2

E

1

C43

CN21

C23

2200/63

D21
D5SBA20(B)

A

C 3/4

VH+

GNDSP
VFDP

F

C 4/4
31

XV-GX3
5

6

7

8

1

2

3

4

3.9 DISPLAY and MIC ASSYS

D

A
V5901
AAV7109-

F+

P1

P2

P3

P4

P5

GR1

45

FL

F+

SG1

SG2

SG3

SG4

37 38 39 40

SG5

35

SG6

SG7

32 33

SG8

SG9

SG10

29 30

P6

P7

P8

P9

P10

P11

P12

SG11

26 27

SG12

SG13

SG14

22 23 24

SG15

SG16

SG17

19 20

P13

P14

P15

P16

P17

P18

8G

1G

GR5

SG18

GR4

2G

GR3

GR10

GR2

9G

GR1

11 12 13 14 15 16 17
GR9

9

3G

4G

8

GR8

5G

7

GR7

6G

6

FL

GR6

10G

7G

5

FL SPACER
AEB7091

F-

F-

FL SPACER
AEB7091

1

DISPLAY ASSY (AWU8275 )

W132

C5914
STBY

GR9

GR8

GR7

GR6

GR5

GR4

GR3

GR2

GR1
VDD

VSS

1
2
3
4
R5904
82k
5
6
7
8
9
10
11

IC5901
PT6315

VDD

FL DRIVER

VSS

CH

CH

CH

FLDC- 12
11
VE+5
REMOCON 10
9
GNDFL
VFL+5 8
7
GNDU
KEY1 6
5
KEY2
JOG 4
3
LED1
VLED+12 2
1
GNDLED

GR10

33
32
31
30
29
28
27
26
25
24
23

W133
1

SG18
SG17
VEE
SG16

SG14

C5918
JQ-T
47/35

SG13

D5902

SG12

STBY

SG15

SG11
SG10

C5917
0.022/50

R5951
1
2
47

SG9

SG8

SG7

SG6

SG5

SG4

SG3

SG2

KEY
2

P.BASS

R5971
1
2
10K
R5972
1
2
10K

REVERSE
MODE

1

2

2

REC/STOP

VE+5

R5965
R5964
3.3k
5.6k
12
1
1

1

2

2

FUNCTION

2

S5964
VSG1024

R5966
2.7k
1

1

1

O/C

2

S5965
VSG1024

R5963
1.8k
2

S5966
VSG1024

1

S5967
VSG1024

R5969
1.5k
2

2

S5969
VSG1024

1

1

S5968
VSG1024

VFDP

SR

RPM7140-H9

R5968
1.2k
2

2

S5961
VSG1024

Vcc
3
GND
2
Vout
1

S5970
VSG1024

47/6.3
C5951
1
2
0.022
R5953
1
2
STBY
R5952
1
2
STBY

1

1

2

S5963
VSG1024

R5967
1k
2

1

2

2

POWER ON

1
1

1

S5962
VSG1024

1
2

R5962
1k
2

C5916
0.022/50

IC5902

100
R5954

C5952 JQ-TS

GNDFL

1

SG1

C5915
0.01/50

C5920
220p
C5921
220p
C5922
220p

VE+5

CN5901

2

1

S5971
XSX3007

R5973
2
12K
R5974
1
2
27K

1

VLED+12

3

R5982

1

1SS355

D5983

SLR-343BBT

VE+5

SLR-343BBT

GNDU

C5981

C5971
1
2
0.022

BLUE LED

220
1/10W

E

PCB BINDER
VEF1040

2
0.01
D5982 D5981

VOL JOG

R5981

F

1k

D

Q5981
2SC4081(QR)

GNDLED

32

XV-GX3
1

2
R5908
STBY

C5919
STBY

12 13 14 15 16 17 18 19 20 21 22

52045-1745

D

C5912
0.022

C5911
0.022
R5902
R5903

2
STBY

10
L5902

C 1/4 CN5651

R5901

1

LAU100J

FLDATA
17
FLCK 16
FLCS
15
VFDP 14
13
FLDC+

Q5902
STBY

44 43 42 41 40 39 38 37 36 35 34

220
220
220

STBY

STBY

2
R5907
STBY

R5906

VEE

C5908
STBY

STBY
D5901

STBY
C5903

L5901
LAU220J
22

JQ-TS

STBY
C5904

1

R5905
STBY
1
2
Q5901
STBY
47/6.3

C

C5906

47/35
JQ-T
C5905

VFL+5

C5913

B

C5907

2

3

4

5

6

7

8

E

A

MIC ASSY (AWU8276 )

JA3901
AKN7003

(MAIN)

VA+12

7
6
2
3
4
5

C3917
1200p

GNDA

MIC AMP

CN3901

C 2/4 CN3051

1.5k

B
C3919
0.1

R3911
12k

C3916
2.2/50
AT-T

CH

7

8
C3918
STBY

C3915
STBY

6 -

R3910

C3912
47/16
AT-TS
0.1

C3905

0.01

C3904

R3904

STBY

C3902
100pF
CH

IC3901
BA4560RF

BA4560RF
IC3901
4
5 +
(2/2)

R3908
3.3k

C3903
100pF
CH
R3903
STBY

(SUB)

R3905
10k

R3902
3.3k

1

R3907
47k

(1/2)
3 +
4

C3911
2.2/50
AT-T

C3910
2.2/50
AT-T

8

C3913
0.1
C3914
100pF
R3909
3.3k

C3907
STBY

1
2
3

100K

2 -

C3906
STBY

RKN1004

330p

R3906

C3901
2.2/50
JQ-TS

R3901
3.3k

JA3902

CH

VR3901
ACS7042

1

C3908

52044-0545
GNDC

MIC SW

1
2

ECHOCONT

4

VA+12V
MIC
GNDA

C3926
0.047

AT-TS

0.01

22/25
C3925

R3922
4.7k

C3924

0.01

MUTE 15
Vcc 14

BIAS

ADINT IN 13

DAINT IN
DAINT OUT

ADINT OUT 12

DALPF IN

ADLPF OUT 11
ADLPF IN 10

DALPF OUT
MIC OUT

MIC IN 9

STBY
L3921

R3930

C3930
0.01
R3925
10k

C

C3932
0.012

R3926
R3928 8.2k
12k

R3927

R3923
12k

100/16

C3923

CR 16

ECHO VR

C3933
AT-TS

R3921
15k

GND

4700p

C3922
0.47/50
AT-TS

1
2
3
4
5
6
7
8

C3931

C3921
STBY

C3928
STBY R3924

IC3921
M65855FP

120k
C3929
0.1

MIC ECHO

5

D3921
UDZS5.1B

(MIC)

R3929
680
10
(1/10W)
W106
R3931
STBY
STBY
(1/10W)

3

12k

D
C3927
4.7/50
AT-T

NOTES

51048-1200

J3992
AKN70037
6
2

STBY

C3992
STBY
L3991
STBY

1

C3993
0.1

C3995
0.01
C3996
0.01

1

2
R3993
STBY

C3991

3
4
5

KN3991
VNF1084

GNDHP

1

SPL

2

SPL

3

AMPL

4

AMPL

5

HPL

6

GNDHP

7

GNDHP

8

HPR

9

AMPR

10

AMPR

11

SPR

12

SPR

ALL CAPACITORS ARE IN µF
UNLESS OTHERWISE SPECIFIED

E

CKSRYB**K50

C 3/4 CN3991

JA3991

JQ : CEJQ**M**
AL : CEAL**M**
AT : CEAT**M**

ALL RESISTORS ARE IN
RS1/16S***J
RS1/10S***J

ALL INDUCTORS ARE IN µH

GNDC

F

LAU***J-TA

E
33

XV-GX3
5

6

7

8

1

2

3

4

3.10 WAVEFORMS
Note : The encircled numbers denote measuring point in the schematic diagram.
A

B DVDM ASSY
Measurement condition ;
No. 1 to 10 : reference A1 (DVD), T2-chp 19, Color-bar
No. 11 to 14 : reference A1 (DVD), T1

1

IC201-pin47 [FG]
V: 1V/div. H: 2msec/div.

GND

B

2

IC201-pin 39 [TROPENPWM]
V: 1V/div. H: 5µsec/div.
[Tray stops]

[Tray is opening]

[Tray is closing]

GND

GND

GND

C

3

IC201-pin37 [DMSO]
V: 1V/div. H: 10µsec/div.

V: 1V/div. H: 10µsec/div.

[TRAY OPEN]

V: 1V/div. H: 2sec/div.

[DVD PLAY]

[DMSO]

GND

GND
PLAY

D

Pless OPEN key

GND

Tray :
opening
Pless PLAY key

Braking a turn of disc

4

CN102-pin 11, 10, 9 (IC101-pin 14, 13, 12)
[SPINDLE (WVU)]
V: 2V/div. H: 2msec/div.

11

IC201-pin225 [ASPDIF AUDIO DIGITAL SIGNAL]
V: 2V/div. H: 500nsec/div.

GND
GND

E

8

IC401-pin23 [CompositeVideo Out]
V: 1V/div. H: 10µsec/div.

9

IC401-pin21 [S VIDEO OUT - Y]
V: 1V/div. H: 10µsec/div.

10

IC401-pin26 [S VIDEO OUT - C]
V: 1V/div. H: 10µsec/div.

9
9
GND

GND

10

F
10
GND

34

XV-GX3
1

2

3

4

5

6

7

8

4. PCB CONNECTION DIAGRAM
NOTE FOR PCB DIAGRAMS :
1. Part numbers in PCB diagrams match those in the schematic
diagrams.
2. A comparison between the main parts of PCB and schematic
diagrams is shown below.
Symbol In PCB
Diagrams

Symbol In Schematic
Diagrams
B C E B C E

Part Name

A

3. The parts mounted on this PCB include all necessary parts for
several destinations.
For further information for respective destinations, be sure to
check with the schematic diagram.
4. View point of PCB diagrams.

Connector

Capacitor

Transistor

B C E
B

C

E B

C

SIDE A

E
Transistor
with resistor

B C E
D

G S D

B

G S
Field effect
transistor

D G S

P.C.Board

SIDE B

Chip Part

Resistor array

3-terminal
regulator

C

4.1 LOAB ASSY

D

SIDE A

SIDE B

A LOAB ASSY

A LOAB ASSY
VNP1836-C

LOAB

5

VWG

1
C102
C101

5

(VNP1836-C)

(VNP1836-C)

LOAD+
LOAD-

SW2

1

CN601

5

V+3D
(V+5D)

5

VWG2279VWG2346-

GND

1

CN602
1 2

E

PNE-1B1

S101

5

CN602

1

CN601

CN602

CN601

CN601

CN602

B CN104

M
LOADING MOTOR
ASSY

F

A

A
35

XV-GX3
5

6

7

8

60

3

70

80

90

100

4

120

R481

R

A

CN104

R921
GNDD
5V

Q481

R922
R923

C237
R924 C421
C422
C423
C424

UP SIDE

CN902
CN902

5

C425
C426
C474
C475
C476

GNDA

R

C451

Q505

C513 C514
R511 R512

L
C1001

Q401

C CN3001
To PICKUP ASSY

R539
R538
R537

R602
R601

R243
R244
R245
R246
R252
C258
C263
C267

C216
R206

B
C220
R232
C219 R284
R216

2/2

R265 R263
R264 R262

D
D861
D862
D821
D851

D852
R821
Q821
Q851

R225
4
IC201
129

R270
R241

R269

R223

R261 R260
R259 R258
R235
R234

1
CN204
R219
R218

R242
C252

C290
5

IC204
1

R224
C223
C222

4

R591
B

C201
C714

64

C739
1.8V

A

R207

C202

C310

C213

C204

R214
C206

C215

3.3V

L309

1

IC711

R735
R740
D731

8

4

R801

R713
R737

C738
R739

C

D801

LD_CD

UP SIDE

C151

R734

C143
C144

Q881 C
D881 C752

GNDM

5

C735
C736
R732
R733

D733

1
7

5

3

4

CN101

C732
C731
GNDD
C702

5

1

C1002

GNDD

CN901

1

12

1

2
3

R750
L751

E

22

R909

R906

R904

CN102
1

C734
C733
L731
R764 C763
R763 C762
E

C754
5V

6.5V

4
1

C152

C566 R313
Q305 R318
R315

R314

CN101

24

C701

8V
25

CN901

C371
1

8

R220
R221
C224

C270
C271
C272
C273
1
5

9

4

5

3.3V

D C712
C801

3.3V

Q307

C533

C563
R562
C565

1

C103

R566 R565
R563
R564 R373

R571R572

1

CN103

C CN1501

LF

L308

C133
C142
C141

R534

C562

C568
Q564

C573 C574

R569
R568
R567

1

C502

1
R506
R505 R504

C532

9
1

R579

R582

CN903

R209

1

R253
R251
C259
C262
C265

C454

R503

3

IC591 4

R509
R508
R507

C508
C503

9

C543C544
R541R542

R549 C539
R548

R533
R535

R536
R578

7
R573

R280

R404
R405
5V

GNDD

27
Q504
Q503
R543 Q531
R545
R546 Q506
R520
Q532

C541
IC531
C542
C534
C537 R531

R552

Q534
C569

C376

C373

C372

Q304

Q563

R915
R914
R913
R912
R911
R910
R908
R907
R905
R903
C104
C140

R522

R521

C509

R544
C531

Q535
Q565
Q561

R136
R135
R133
C102
IC101
C153

R151

R152
R154

1

GNDD

R518
R519
Q501

C511
C512
IC501

C504

R514

R515
R516
Q502
Q533

C536
R325
C535 R326
Q308

C161
R153

C101

R762

IC761
R901

C507 R501 C501

R592

R593
R595
C506
C505 R502
R594
R310
C320
C309
R532
R322
LD_DVD

R321

R134
R132
R131

Q801
C145

C131
C132

C761

R761
R751
C751
D751

R731
Q702

R256 C268
C269

C251

256

C344
C343
C346
C345

R714

R736
C146

1

C203

R712
3

5

R401

193

128
65

R200
C221
C711
4

IC731
IC751 C753
R702

Q701

C404

R436
R435
R434
R432
R431
R433

R413

R226
192

R416
R415
R414
R412
R411
X201

R229
R228

R227

C242
R279
C243
C244

C209 C205
R201
R202
R204
R205

R211 C217
R210

C208
C210
C211
C212
R215
R213
R212

R217

R237

C713
R711

R738
C737
C740
R883 R853 R824
R882 R852 R823

Q731
L732
R881 R851 R822

110
R581

50

R575
C571
IC561
R576
C572
Q562
C564
R574
R561 C561
C567
C374

40

V

30

R513

20

R551

2

B

A CN601
10

(ANP7527-A)

Y

60

C538
1

1

XV-GX3

36

B
0
X

F

CN104

0
10
20
E

30
40
50
D

70
80
90

C

100
110
120
B

130

R701
12V

140

CN103

BOTTOM SIDE
UP SIDE

BOTTOM SIDE

UP SIDE

CN102

B DVDM ASSY

To SPINDLE MOTOR
To STEPPING MOTOR

A

SIDE A

SIDE A

4.2 DVDM ASSY
1

2

3

4

5

6

7

8

XV-GX3

37

B
120

B
110

100

90

80

70

60

50

40

30

20

0
X

10

F

(ANP7527-A)
0

Y

IC401

C281

R247
C248
C236

C414
C415
C416

C246
C245

IC202

R422
R423
R424

C413
C405

R425

1

R474

C464
C465
C466

R230
R231
R268

R475
R476

C241

IC451

C256
C214

C255

R255

C261

C347

R590

1

R240

C592

C264

C207

C591

IC203

R233

R254
C254

R248

8 C455

R257
C253

9

C227

C228
C230

C250

C282

C453

16

C240

15 R426
C452

14

C239
R238
C247

C235
R266

R403
R402
C406

C402
28

1

C412

28

R267
C233 C234
27
C283

C287 C288

R421

1
C286

C232
C226 C231

R249

R236
R285
25

48

R1002

R281

R239
C225
C289
C296

R1003

C403
C411
C284

C285
54

E

R282

C218

13

C500

R517

C257
C260
C266

24

R604
R603

CN951

1

R1001

C401

10
20
30
40
50
D

60
70
R208

R500
Q201

80
2
CN952

1

1

D732

3

C530

Q732
6 4

R547

C

90

R530

100

PRODUCTION CODE

0

1

A
B
C

C560

C121

1

R560

0

ICT

DVDM ASSY
AWM7 0 0 0
111
222
333
444
555
666
777
888
999

R577

0 1 2 3 4 5 6 7 8 9

0 1 2 3

110
120

FC

C1003

B

R917
R371

R372

R916

R902

R375
R374

L901

130

LF

R303
R302

R301

140

B DVDM ASSY
A

SIDE B

SIDE B
5

6

7

8

1

2

3

4

4.3 MAIN ASSY
SIDE A

C

A

MAIN ASSY
VIDEO

DI P

AUDIO

230

W420
W290

W399

D3627
C3624

D3623

W357

W400

W358

R3625
C3622

R3622
W323

W359

R3623
R3621
D3603

W356

W324

W322

C3601

C3304

(R3328

W291

W236

C1505

R3345

W325
C3317
W120

W248

W119

W525

W107
W106

W502

UPPER SIDE

W115 SPL

SPR
W144

W528

C3057

W526

W501

D2901

W105

D2902
W104

W108

C1506

R2908

R2907
W102

W101
1

W103

1

R2909

XREADY

W523 XRECMUTE

11

W514

W519

C1507

W520 SCLK

7

10

R3326
W245

W139

W521 MDATA

AMPL

W524 VDET
W522 SDATA

GNDU

20

R3991

W176
W109

C5583

W516

VE+5

W512

W114

W142

R3992

W174

1

25

W527

W513

W171

AMPR W113

30

W517

KN3

W511
W510

W518

W162

W110

W168

W531

TCMODE

W530

W163

C5586

W515

W164

L5501

W141

W169
W529
W165

W175

W170
W173

W159

40

D3511
C3318
W246

C3315

W112

X5501

W160

50

D3307

R3322

R3321
W243
R3346

L3302

W161

E

W276

C3623

C5589

W197

L3301

W199

R3337

W194

W186

W187

W242
D3309

W196

W185 VD+5

R3338

W239

R5563

C2802

70
60

IC3301

C3320
W235

W230
W232

W202

PRINT SIDE

Q2801

W532

W237

C2803

W12

D3303
D3301
R3325

W244

W272

C3314

W234

W233

W238

R5507 W229

W220

C2801

W117
W116

W231

W227

W269

C2103
W226

W224

PB/XREC

W225 XBEATCUT

W268

BIAS
W223

W222

W221

XPROTECT

C2808

CN2302

1

R2815
W218

C3313

15

OPEN SIDE

R2803
C2810

W293

D3305
(R3327

W273
W228 XSYSMUTE
C5411

R2805

D2101
C2105

D2102

D2305

W271

W266
C2805

L2801

Q2802

C3306

W274

Q2805

C2804

C3305

(

W263

Q2806

80

C3523

L2802
W265
C2807

VR2801

90

W270

W241

W289

W275

W288
L2101

C3524
D2307

D2304

4

D2301

W267

D2303

W264

D2302

OPEN SIDE

L2811

1

123.0mm

C2813

L2812

word surface

1

CN2301

C2814

Q2301

VR2802

100

W296

C3303

D3304

D2306

110

D3512

D3308
D3306

Q3301

GNDP

VR2302

W287
W286

W294
XPROTECT
Q3302

W295

VR2301

C2816

Q2302

1

CN2301

R3512

D3506

W292
C3529

C3013

C2305

D3302

C3014
C2410

W316

123.0mm

C2409
C2815

120

CN2302

D3504

C3316

C3302

CONTACT SIDE

To DECK MECHA

D3508

2232

W125
C3060

W310

130

D

R3627

304

Q3501

W126

C3301

C

D3601

C2324

W313

C2323

D3510

W311

C2306

W315

W129
W314

VR2402

W312

CN3001

C2322

1

CN3001

W355

W321
W130

Q3502

27

B CN902

D3507

W351

C3059
W308
C2321

140

R3511

W353

C2402

D3621

D3505

C3045
C2325

D3624

W395

C3046
C3054
C2326

( W398

W396
C3035

D3503

W350

W309

C2401

VR2401

W397

W423
VA+12

W394

C3036
C3041

Vref

W389

W349

C3021

D3509

W352

GNDA

W341

150

W401

C3042

W348

C3019

W347
W342

W340

C3107

C3108

W354 VA-12

EVOLDATA

W127
X5701

CONTACT SIDE

W339

W388

C3024

C3056

C3023

C5718
C5721

EVOLCLK
W136

170

GNDA W418

W417

C71

W383

W381

W384

C5704

W380

W379
W343

1
11

CN5701

W386

W135

C3003

C3004

5

CN5701

W416

C3055

W414

C8871

180

PRODUCTION CODE

C3997

C74

190

W424

W415

200

160

C

NP

C8881

C8851

210

JA3992

W419

JA3001

W421

C8831

CN8802
JA8801
C8861

W422

(

To FM/AM TUNER UNIT

JA3301

(

B

ICT FC

220

CN1501
CN3051
CONTACT SIDE

Y

CN5501

CN2901

0
0
X

F

10

20

30

40

50

60

70

80

CN2901

C
38

90

100

110

120

130

CN1501

To DECK MECHA

B CN901

XV-GX3
1

CO

CONTACT SIDE

2

3

4

140

150

160

CN3051

E CN3901

5

6

7

To DC FUN MOTOR
DI P

240V
POSITION

CN3651

HOLDER

C3653

W447

W446

FU1

200
W438
W412

190

W411

H5

FU2

H2

D3627

W403
W357

H4

D3653

CN3651

W440
W439

C1

W400

W441

Q3654

W399

W402

180

W366

IC51

W333

W328

140
CN2
W306

130

2

1

C5

(

W283

W282

10

D14

D41

Q12

D12

100

RY1

C11

R41

W278
W279

R16

C44

80
W217
W216

70
1

W214
W215

CONTACT SIDE

160

170

180

CN3051

190

200

210

220

D52

W184

R51

Q51
(Q54
D55

KN2

D53

E

D81

C5581

40
30

W508

W156 SYSPOW

R84

20

D83
R82

W507

W506

ATTENTION
EN CAS REMPLACEMENT DES FUSIBLES IC3303 N'UTILISER
QUE LA REFERENCE 491007 DE CHEZ LITTELFUSE INC.

150

VFDP
W157

W183
W505

W504

C81

D82

REPLACE WITH SAME TYPE
#491007 FOR IC3303 MFD.
BY LITTEL FUSE INC.

CN3991
CN3051

C53

D21

D31

W155
C31
W503

W153

W152

W151

12

W150

10

BOND

CAUTION
W149

W501

1

5

W527

1

AWM8015
AWM

W148

C3057

MAIN ASSY

C21

AMPL

CMKM-P3X

AWM8013
AWM8016

50

C54

BOND

C22

1565

C32

4700/35

W181

W180

W212

W211

W210

W206

W147

W146

W205
VPR+8

IC3303

17

W502

W179
IC3304

W115 SPL

SPR
W144

W528

R3991

W114

AMPR W113

R

60

(

LF

W182

1

R3345

L3301

C13
W204

D51

C12

W207

CN21

W261

C41

W257

W208

BOND

W245

IC11

D

W262

W213

W209

90

C51

W254
R3337

FU4

2200/63

W256

D3625

D43

W255

R3338

H8
H7

R3626

D44

W124

W253

W123

Q41

C43

D3626

C47

6800/25

W252

C3315

SECONDARY

1565

W120

W248

W119

W246

W250

W251

R3992

110

T2

7812

W285

W280

IC42

D3305
(R3327

W121

IC61

(

C3317

C61

D3303
D3301
R3325

L3302

120

1

C64
D61

CN1

W305

W303

D3511
C3318

D3307

R3322

W297

W281

C

W307

Q61

2012

W299

W302

W298

H3

H6

150
W375

D3605

W300

W337

W374

D3604

W329

160

W334

D62

W301

W296

GNDP

W338

C65

79012

W324
W325

W331

170

4

D57

W359

D3602

PRIMARY

W304

W322

D3601

W372

C3

R3326
W295

W373

W131

C57

C3602
W330

D3302

W132

W133

W404

W358

R3625
C3622

W323

R3622

D3603

W361

W327

D3512

W367

W363

FU3

W365

L1

C3624

D3623
R3621

W370

W362

C3316

40

B

W371
W360

W134

( W398

(
R3623

KN1

H1

C3652
C3651

1

W401

D3624

210

W433

W426

C3601

220

D3651

W427

D3621

S101

R3651
AN1

W432

W428

W356

230

D3654
S102

7

A

W445

W425

5

SIDE A

240V
POSITION

D3652

CT FC

3

8

10

Q81

CONTACT SIDE

CN5651

Y
230

CN3991

240

250

260

270

280

290

300

310

320

330
F

CN5651

(ANP7548-A)

E CN3901

E J3992

C

D CN5901

39

XV-GX3
5

6

7

8

330

320

310

300

10

R5653

Q53

290

40

2

Q52

280

270

1.FLDATA
2.FLCK
3.FLCS

10.VFL+5 4.VFDP
11.GNDU 5.FLAC
12.GNDU 6.FLAC
13.KEY1 7.VE+5
14.KEY2 8.REMOCON
9.GNDFL
15.JOG
16.LED1
17.LED2
18.VLED+12
19.GNDLED

R55

Q5503

C82

260

F

GNDFL

CONTACT SIDE

CN5651

CN5651

250

240

3

230

220

AWM
7 0 0 0 -A
8 111
C3323

R3343
C3325

210

VH+

SECONDARY

CN3991

200

CN3991

190

C

XV-GX3

4

180

GNDP

GNDA

VM+12

VL+

IC41

R3613

R3616

VLR3615
R3610
R3611

Q3604

CMKM-P3X

CONTACT SIDE

170

R3614

PRIMARY

R3617

C56

R3629

E B C2

AMPL

R61

180

SPR

222
333
444
555
666
777
888
999
SPL

R62

190

5.GNDA
4.MIC
3.VA+12
2.ECHOCONT
1.MICSW

C63

R3628

R3655
R3654
R3656

CN3651

R3653

R3652

LIVE

NEUTRAL

Q3651

2.SPR
1.SPR

C62

R3602

Q3653

3.AMPR

TH3601

R3608
R3607

R14

140

4.AMPR

VPR+8

4
R3604
R3603

1
R3606

3

7.GNDHP
6.GNDHP
5.HPR

Q3602

2

9.AMPL
8.HPL

E
Q3601

11.SPL
10.AMPL

60
D11

12.SPL

C14

Q11
R12
R11

R15

200

R5583

C42

R3605

100
D13

FLCS

C36

110

FLDATA

C35

210

FLCLK

C34

220

GNDLED

40
C33

50

R56

R5581

B

R5582

C26

90

C24
C23

170

C25

D

VFDP

70
1

R5580

10

20

SYSPOW

120
1

30
R81

2

1

CN2

150

1

Y

C

1

A

17

SIDE B
3

5

130

CN1
4

C

CN21

160
NP

B

2

1

1
4

MAIN ASSY

230

Q3652
NP

0
0
0

C B2 E2
Q3629

CN3051

160

Q3623

Q3628

Q3622
Q3624
Q3621

VA-12
D3622

NP
NP

NP
Q3605

Q3606

VH-

VA+12

VL+

VPR+8
VD+5
D3323
Q

80
VE+5

VUN+8

R

MIC

CN3051

0

15

120

110

100

5

1

UPPER SIDE

25

CONTACT SIDE

CN1501

90

80

6

70

CN2901

60

50
VD+5

R5550

IC5401

40

7

30

Q5502
TCMODE

Q2901

CONTACT SIDE

20

4

1

1.Rch
2.GNDA
3.Lch
4.GNDA

CN2301

Rch

150

140

Q2304

1.BIAS
2.GNDB

A

GNDU

NP

CN2901

10

CN3001

27

R5714

C5720
R5705
R5706
C5717 C5710
C5711

C3022

CONTACT SIDE

R3011

R3034
C3034

32

C3020

01

30

C5705

R5713

CN5701

180

C5701
R5703

C5709

C5708

C8832

R8832

R8842

L8861

R8853
R8876
R8873

R8855

R8821

C73

R3103
R3104

R8865 R8866

C5702 C5707
R5704 C5706

C5722

R3006

R3005

C72

GNDA

R3032
C3032
C3027

C3328

C3329
C3331

C3996

R3352

R3350

R3007
R3003

C3030
R3030 (

C3033
R3033

C3031
R3031

R3039

C3038
C3040
R3036
R3038
R3040

CONTACT SIDE

CN5701

VA+12

C3029
R3029 (

C5719

C5723

R3041
R3042
C3044

R3037

R1501 R1504 R1502
C3026

R3505

C3621
R3624

R3628

1.GND
2.RDS
3.VSM
4.TXR
5.+9V
6.TXL
7.GND
8.DO
9.CLK
10.DI
11.CE

110
CN2301

1

CN3001

R3509

R3503

R3629

R8875
L8871
C8872
R8863 C8862

R8856

F8831

F8841

R8822
L8821
C8822
C8852
L8851

C8842
R8835

C3105
C3103
C3104
C3106
R3101
C3101
C3102
R3102

R3001
C3001
R3002
R3004 C3002

C3332

C3330

C3327

R3349
R3351

7

90

80

CN2302

Lch

R2814

Q2303

BIAS Adj

Q2352

C5712 C5713
C5703 C5714
R5715 (

EVOLDATA

1

27.FR
26.GNDA
25.FL
24.GNDA
23.GNDD
22.R
21.GNDD
20.B
19.GNDD
18.G
17.GNDD
16.Cr/R
15.GNDD
Lch
14.Cb/B
13.GNDD
RECLEVEL Adj 12.CY/G
11.GNDD
10.SY
9.GNDD
8.V
RECL
7.GNDD
6.SC
5.ASPECT
4.VSEL1 2.SQUEEZE
3.VSEL2 1.P/XI

R2405

EVOLCLK

OPEN SIDE

OPEN SIDE

R2403
C2405
C2407

R5707

C3018

R3013

C5715

C5716
R2401

R2406
C2404 R2402
R2408
C2406
C2408
R2410

R2404

C2403
R2407

17

IC

C3025

SC

R2804

R2302

R2409

RECR

16

R3504

R3513

C1509
R3035
R3043 C3039
C3047 C3037
C3049

C3015
R3012
C3017
C3016
GNDA

R2312

1

R2323 R2321 R2311

R2353

R2322

C3012 C3011

R3051

C3053

C3051

R3044
C3050
C3048

C1510

SI

R2813

C2301

C2302

4

C2809

C2303

R2324

C3052

R3532
R3533

R3530
R3527
C3527
R3529

R3301

R2354

Rch

R2301

R2325

R2326

R2304 C2304

R2327
R2303

R2328
R2329

R2330

C3525
R3526
R3524

C3528
C3526
R3528
R3523
R3525

R3531

R3307
R3303

R3302 R1503

NP

R3514

R3614

IC5701

CN2302

R2816

R2811

R2822

R2824

R2821

R2823

R3308
R3306
R3304

PB LEVEL Adj

R3309

R3305

R3310
R3356

R3510
R3506

R3615
R3610
R3611

Vref

R2802

R2801

C2812

R2352

C2811

R2101
C2101
R2102
R2103
R2107
R2351

R2108

R3522
R5411

C3522

1

R3364

R3363

R3612

R3613

R3616

VA+9

1.FLASH E/D
2.FLASH DO
3.FLASH CLK
4.XRESET
5.VE+5
6.GNDU
7.NC

Q2906
R5539
R5540
R5541
R5542

C2106

R2810

R2109

Q2351

R2911

UTEST
R5543 R5547
R5548 R5549

XPROTECT

BIAS

PB/XREC

R5559
R5558

R5555

XBEATCUTR2104

C2102 R2105
R2106 C2104

R2809

R5556

C5508

XSYSMUTE

R5567

C3521
R3521

GNDB

C5507

R5552
R5551

R5564

R5568
R5566

C3541

R3541
R5412

R3543

R3355

R3314
R3316

R3313 R3547

R3362

Q2101

R5538

50

R5565

R5502

R5501

D3541

R3315
R3311

R3312

C3311
C3307

C3309

R3319
R3317
C3310
R3320
C3312
R3318
R3542 D3542

C3308

R3330

R3342
R3340
R3332
R3323
15

R3361

NP

R5537

C5506

31

C5501

R5511

R5510

R5506

C3319

R3630

R3341
R3339

R3329

GNDP

Lch

R5401

R5514

R5512

C5587

R5504

D5502

R3544

R3546

R5503 C5582

D3543
R3545

R3344

IC3521
5
8

PBR
PBL

R5572

R2905

R5531
C5505
R5544
C5401
R5546
R5545
R5402
C5402

R5522

C5504
R5521

R5519

R5586
R5587

D5501

R3335
R3333
R3334

R3348
C3324

C3326

R3347

R3343
C3325

Rch

R2902
R2901

2.SOL
1.GNDM

XRECMUTE

R5525
R5526
R5527
R5528
R5529
R5530
R5535
R2906

R5513

SDATA

6.MODE
5.HALF
4.PULSE
3.N.C.

SCLK

R5516
R5515
C5510
C5509

XREADY

GNDTCM

MDATA

R5532

R5517

C5585

R5585

C5588 R5584

VDET
Q5411

R2903
R2904

CN1501

11.RECR
10.MOTOR
9.RECF
8.VD+5V
7.GNDM

C1502

C5584

C1503

C1501

C3058

AMPR

C3323

51

5
NP

01

130
XDVDRST

55

140
4
1

IC

AMPL

Q3521
5

30

CN3051
Q3541
8

80

1
Q3542
81

D3321
Q3625

1

SPR

1

0

SPL

Q3321
Q3303

DVDR

10

Q3304

11

D3323
Q3305
EVOLOUTL

10

5.GNDA
4.MIC
3.VA+12
2.ECHOCONT
1.MICSW

XPROTECT

IC3522

Q3322
EVOLOUTR

DVDL

1

R3617

VA-12

1

Q3504

TXR

7

NP
NP
4

GNDREG

(

Q3606
D3502
IC71

10

D3622
5

TXL

11

Q3605

6

1

NP
1

64

L+

Q3503
IC3031
8

5

D3501

25.VDVD+12
24.VPR+8
23.VPR+8

150
LINEINR

C3043

MIC
Q3620

33

Q3603

LINEINL

49

CN3051

1.NC

160
Q3003
Q3001
NP

8

LINEOUTLLINEOUTR

4

Q3622
Q3624
Q3621

22.VPR+8
21.VPR+8
20.GNDM
19.GNDM
18.GNDD
17.GNDD
16.DOUT
15.GNDD
14.GNDD
13.CVDPOWER
12.XDVDRST
11.XREADY
10.SCLK
9.SDATA
8.MDATA
7.DVDACK
6.GNDD
5.GNDD
4.VDET
3.DVDMUTE
2.TRKUP

170
Q3623

48

CONTACT SIDE

Q3628
A
B
C

(

X
1

1

Q3629
0 1 2 3 4 5 6 7 8 9

(

Q3604
1

9

0

16

0

8

0 1 2 3

1

5
8

SIDE B
A

230

220

210

200

190

XV-GX3

8
B

170

160

C

130

120

100

D

70

60

50

STEST

40

VE+5

E

Q2902

30

Q2905

CN5501

20

10

0 Y

0
X

(ANP7548-A)

F

C

41

120

1

110

100

90

80

42

2

70

S5962
POWER

S5963

W123
FLDC-

1

L5901

C5908

IC5902

C5952

C5913

60
P.BASS

S5964

W133

FL SPACER

W114
GR10

REVERSE MODE

S5965

VFDP

W115

V5901

W125
REMOCON
W126
GNDFL

W120
VFDP

W121
GNDFL

REC/STOP

S5966

CONTACT SIDE

17

C CN5651

W116
VFL+5

CN5901

W118
FLCS

D

W119
FLDATA

VFL+5

C5918
S5967

45

FL SPACER

FUNCTION

CN5901
W131
JOG

W129

C5907

C

W132

D5981

FC ICT

DISPLAY ASSY

S5970

AWU8275
AWU

S5971

GNDU

S5969

W130

S5961

B

L5902

R

2/2

CMKM-P3X

LF

D5982

S5968

D

W124
VE+5

SIDE A

W128
KEY1

A

W127

1

E

Production Code

1
2
3

50

40

D

3

4

4.4 DISPLAY ASSY

DISPLAY ASSY
SIDE A

330

320

310

300

290

280

270

260

250

240

230

220

210

200

190

180

170

160

150

W117
FLCK

140

30

130

(ANP7549-A)

120

F

110 Y

20

10

X

0

180

XV-GX3

D

4

VE+5

5

6

7

8

XV-GX3

D

43

D

X
0

10

20

30

40

50

60

70

80

90

100

110

120
F

Y

110
(ANP7549-A)
POWER

120
R5953
C5951
R5951
R5952
R5954

R5962

C5911

C5904
C5906

I

A

130

FLDCC5912

140

VFL+5

FLCK
FLCS

R5907

R5905
Q5901

FLDATA

C5920 R5901
C5922 R5903
C5921 R5902
R5904

D5901
C5914

R5906

1

GR10

Q5902

11

R5908
R5964

12

33

REVERSE MODE

C5915
22
IC
59
01

23

VFDP

E

1.GNDLED
2.VLED+12
3.LED1
4.JOG
5.KEY2
6.KEY1
7.GNDU
8.VFL+5
9.GNDFL
10.REMOCON
11.VE+5
12.FLDC13.FLDC+
14.VFDP
15.FLCS
16.FLCK
17.FLDATA

34

44

P.BASS

150
160

C5919
D5902
C5917
C5916

170
180

R5965
17

CN5901

GNDFL

VE+5

VFDP

H

REC/STOP

190
200

D

REMOCON
GNDFL
VFL+5
1

210

KEY1
R5966

C5903
C5905

B

FUNCTION

220
230

JOG

DISPLAY ASS'Y
G
LF

C

VE+5
R5963

AWU8275
AWU

R5969
R5981

Q5981
R5982
R5971
R5973
R5974
R5972
C5971

D5983

C

240

C5981

250
260
270
280

R5968

GNDU

B

E

280

D

R

R5967

F

CMKM-P3X

300
310
320
330

D DISPLAY ASSY

SIDE B
5

A

SIDE B

6

7

8

1

2

3

4

4.5 MIC ASSY
SIDE A

SIDE A

A

E

MIC ASSY

250

240

C CN3051
230

B

CN3901

220
CN3921
5

CMKM-P3X

GNDA

W107
MIC SW

CONTACT SIDE

C3922

190

C3927
C3912

150

C3911

W112

160

MIC IN

C3918

C3933

170

C3916

180

W105

C3925

C

DALPF OUT

L3921

W106

R

200

UPPER SIDE
W108

1

210

C3910

C3901

130

VR3901

W111
GNDA

140
D

JA3901

W103

A

90

12

W110
AMPR

JA3991

HPR

80

W102

Y

HPL

J3992

1

KN3991

J3992

W109

70

W101
HPR

E

GNDHP

LF

100

AWU8276
AWU
MIC ASSY

110

JA3902

W104
GNDA

1/2

120

60

0

F

10

20

30

40

50

60

70

C CN3991
80

90

100

(ANP7549-A)

110

120

130

X

E

E

44

XV-GX3
1

2

3

4

5
MIC SW
R3931

R3930
C3928
C3929
R3924
C3930
R3925

R3908
R3907
R3905
D3921

R3910

1

C3919
C3915
R3911
C3917

IC3901

MIC IN

150

D
C3907
R3906
C3908
C3906

AWU8276
AWU
MIC ASSY

110
GNDA
C3903

C3902

100
R3903
R3902
R3901

LF
R3993
C3993

C3905
C3904
R3904

12

GNDHP

L3991

70

C3995

HPR

HPL

R3909
C3914
C3913

AMPR

HPR

C3931
R3926
R3928

160

1

16

CMKM-P3X

8.HPR
9.AMPR
10.AMPR
11.SPR
12.SPR

R3929

C
IC3921

170
C3932

E

90
1.SPL
2.SPL
3.AMPL
4.AMPL
5.HPL
6.GNDHP
7.GNDHP

GNDA

180
DALPF OUT

J3992

210
5.GNDA
4.MIC
3.VA+12
2.ECHOCONT
1.MIC SW

200
C3926
C3921
C3923
R3921
R3922
R3923
C3924
R3927

R

C3991

1

Y

C3996

F

0

10

20

60

(ANP7549-A)

80

C3992

220
CN3901

8

7

6

5

140
4
1
GNDA

5
8

30

40

50

60

70

80

90

100

110

120

130

MIC ASSY

E

8
7
6
5

SIDE B
SIDE B

A

250

240

B

230

190

130

120

X

E

E

45

XV-GX3

8

9

1

2

3

4

5. PCB PARTS LIST
NOTES:
A

B

Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
When ordering resistors, first convert resistance values into code form as shown in the following examples.
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%,
and K=10%).
560 Ω
56 x 10 1
RD1/4PU 5 6 1 J
561
47k Ω
RD1/4PU 4 7 3 J
47 x 10 3
473
0.5 Ω
RN2H R 5 0 K
R50
1Ω
RS1P 1 R 0 K
1R0
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
5.62k Ω
562 x 10 1
5621
RN1/4PC 5 6 2 1 F
Meaning of the figures and others in the parentheses in the parts list.
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding
PC board.
IC 301 (A, 91, 111) IC NJM2068V

Mark No.

Description

Mark No.

Part No.

LIST OF ASSEMBLIES
NSP

C

1..05 LOADER ASSY
2..LOAB ASSY

VWT1219
VWG2346

1..DVDM ASSY

AWM7966

1..MAINASSY (DFLXJ, DDXJ/RD)
1..MAINASSY (DDXJ/RB)
1..MAINASSY (MTXJ)

AWM8013
AWM8016
AWM8015

NSP

Description

Part No.

1..SUB ASSY
2..DISPLAY ASSY
2..MIC ASSY

AWM8014
AWU8275
AWU8276

1..FM/AM TUNER UNIT

AXX7173

7 CONTRAST OF PCB ASSEMBLIES

C MAIN ASSY
AWM8013, AWM8016 and AWM8015 are constructed the same except for the following :
Mark
>
>

D

Symbol and Description

AWM8013

H3–H6 FUSE CLIP
S101, S102 VOLTAGE SELECTOR
T2 STANDBY TRANSFORMER
R5517
R5519
C33–C36 CHIP CAPACITOR

AWM8016

AWM8015

AKR7001
AKR7001
Not used
AKX7017
AKX7017
Not used
ATT7080
ATT7080
ATT7078
Not used
RS1/16S393J RS1/16S473J
RS1/16S473J RS1/16S223J
Not used
XCG3008

Not used

Not used

7 PCB PARTS LIST FOR DFLXJ TYPE UNLESS OTHER WISE NOTED
Mark No.

Description

Mark No.

Part No.

A LOAB ASSY
MISCELLANEOUS
S 101
CN602 CONNECTOR
CN601 CONNECTOR

E

MISCELLANEOUS
101
201
202
203
204

(A,62 ,106 ) 6CH DRIVER IC
(A,50 ,44 ) DVD IC
(B,34 ,25 ) IC
(B,34 ,54 ) FLASH ROM
(A,19 ,44 ) EEPROM

BD7995EFS
MT1389FE/C2-L
K4S641632H-TC75
AYW7082
S-24CS04AFJ

F

IC 401 (B,92 ,22 ) DVD VIDEO AMP IC
IC 501 (A,98 ,71 ) D/A CONVERTER
> IC 711 (A,33 ,74 ) REGULATOR (1.8V)

Part No.

MM1623BF
PCM1753DBQ
MM1661JH

46

R1224N102H
MM1565AF

> IC 761 (A,41 ,119 ) REGURATOR (ADJ.)

VSK1011
S2B-PH-K
S5B-PH-K

B DVDM ASSY
IC
IC
IC
IC
IC

Description

> IC 731 (A,29 ,92 ) DC/DC CONTROLLER IC
> IC 751 (A,32 ,113 ) REGULATOR IC (5.0V)

Q
Q
Q
Q

304
305
307
308

BA3948FP
(A,77 ,127 ) TRANSISTOR
2SC4081
(A,84 ,125 ) NMOS FET TRANSISTOR UM5K1N
(A,71 ,87 ) CHIP TRANSISTOR
HN1A01F
(A,63 ,87 ) CHIP TRANSISTOR
HN1A01F

Q
Q
Q
Q
Q

481
501
502
503
504

(A,100 ,7 ) CHIP TRANSISTOR
(A,103 ,56 ) TRANSISTOR
(A,94 ,56 ) TRANSISTOR
(A,105 ,69 ) CHIP TRANSISTOR
(A,108 ,69 ) CHIP TRANSISTOR

DTC114YUA
2SD2114K
2SD2114K
DTC114YUA
DTC114YUA

Q
Q
Q
Q
>Q

505
506
701
702
732

(A,98 ,53 ) TRANSISTOR
(A,114 ,69 ) CHIP TRANSISTOR
(A,24 ,134 ) TRANSISTOR
(A,27 ,129 ) DIGITAL TRANSISTOR
(B,22 ,90 ) FET

2SA1576A
DTC114YUA
2SA1576A
DTC124EUA
RSQ035P03

3

4

XV-GX3
1

2

5

Mark No.

6

Description

Part No.

Q
Q
Q
Q
D

801
821
851
881
731

(A,50 ,87 )
(A,42 ,86 )
(A,42 ,89 )
(A,42 ,93 )
(A,29 ,87 )

DIGITAL TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DIODE

DTC124EUA
2SA1576A
2SA1576A
2SA1576A
1SS355

D
D
D
D
D

732
733
801
821
851

(B,18 ,92 )
(A,24 ,94 )
(A,50 ,85 )
(A,46 ,86 )
(A,46 ,89 )

DIODE
DIODE
DIODE
DIODE
DIODE

RSX201L-30
1SS355
UDZS4R7(B)
1SS355
1SS355

D
D
D
D
L

852
861
862
881
731

(A,42 ,82 ) DIODE
(A,46 ,82 ) DIODE
(A,46 ,83 ) DIODE
(A,46 ,93 ) DIODE
(A,23 ,109 ) POWER INDUCTOR(22U)

1SS355
1SS355
1SS355
1SS355
DTL1099

L
L
L
X

732
751
901
201

(A,22 ,84 ) POWER INDUCTOR
(A,34 ,99 ) CHIP BEADS
(B,44 ,129 ) CHIP BEADS
(A,77 ,45 ) CRYSTAL RESONATOR
(27MHz)

ATH7011
VTL1095
VTL1075
VSS1172

(A,88 ,140 ) 0.5-24P CONNECTER
(A,69 ,142 ) 12P CONNECTOR
(A,103 ,139 ) 04P CONNECTOR
(A,79 ,9 ) CONNECTOR
(A,42 ,142 ) 25P CONNECTOR

VKN1482
AKN7031
RKN1045
AKM1291
VKN1317

CN101
CN102
CN103
CN104
CN901

CN902 (A,116 ,28 ) 27P CONNECTOR

7

Mark No.

RESISTORS
131
132
133
134
135

(A,61 ,95 )
(A,63 ,95 )
(A,66 ,95 )
(A,65 ,95 )
(A,68 ,95 )

RS1/10S4R7J
RS1/10S4R7J
RS1/10S4R7J
RS1/10S4R7J
RS1/10S4R7J

R
R
R
R
R

136
151
152
153
154

(A,70 ,95 )
(A,59 ,117 )
(A,59 ,121 )
(A,57 ,117 )
(A,57 ,121 )

RS1/10S4R7J
RS1/10S1R0J
RS1/10S1R8J
RS1/10S1R0J
RS1/10S1R8J

R
R
R
R
R

200
201
202
204
205

(A,25 ,56 )
(A,49 ,67 )
(A,48 ,67 )
(A,47 ,67 )
(A,45 ,67 )

RS1/10S0R0J
RS1/16S152J
RS1/16S223J
RS1/16S223J
RS1/16S184J

R
R
R
R
R

206
207
208
209
212

(A,46 ,64 )
(A,65 ,60 )
(B,27 ,71 )
(A,57 ,16 )
(A,40 ,70 )

RS1/16S224J
RS1/10S0R0J
RS1/10S0R0J
RS1/10S0R0J
RS1/16S103J

R
R
R
R
R

213
214
216
217
218

(A,41 ,70 )
(A,45 ,72 )
(A,36 ,62 )
(A,31 ,61 )
(A,18 ,37 )

RS1/16S103J
RS1/16S0R0J
RS1/16S0R0J
RS1/10S0R0J
RS1/16S103J

R
R
R
R
R

219
221
223
224
225

(A,18 ,35 )
(A,25 ,44 )
(A,29 ,35 )
(A,29 ,49 )
(A,40 ,23 ) CHIP RESISTOR ARRAY

RS1/16S103J
RS1/16S330J
RS1/16S330J
RS1/16S330J
RAB4C330J

R 226 (A,43 ,23 )
R 227 (A,44 ,23 )

Description

Part No.

R 229 (A,48 ,24 )
R 230 (B,71 ,35 )
R 231 (B,71 ,37 )

RS1/16S330J
RS1/16S101J
RS1/16S101J

R
R
R
R
R

232
233
234
235
237

(A,34 ,60 )
(B,42 ,50 )
(A,26 ,42 )
(A,26 ,41 )
(A,23 ,41 )

RS1/16S0R0J
RS1/16S0R0J
RS1/16S330J
RS1/16S472J
RS1/16S330J

R
R
R
R
R

238
241
242
243
244

(B,60 ,35 )
(A,71 ,36 )
(A,71 ,37 )
(A,69 ,39 )
(A,69 ,41 )

RS1/16S103J
RS1/16S330J
RS1/16S330J
RS1/16S100J
RS1/16S330J

R
R
R
R
R

247
248
249
251
252

(B,58 ,37 )
(B,58 ,46 )
(B,59 ,40 )
(A,70 ,47 )
(A,68 ,45 )

RS1/16S103J
RS1/16S330J
RS1/16S103J
RS1/16S104J
RS1/16S0R0J

R
R
R
R
R

253
254
255
256
257

(A,70 ,45 )
(B,65 ,48 )
(B,57 ,52 )
(A,73 ,59 )
(B,64 ,42 )

RS1/16S681J
RS1/16S754J
RS1/16S104J
RS1/16S153J
RS1/16S0R0J

R
R
R
R
R

258
259
260
261
266

(A,23 ,39 )
(A,26 ,39 )
(A,24 ,37 )
(A,27 ,38 )
(B,51 ,38 )

RS1/16S330J
RS1/16S330J
RS1/16S330J
RS1/16S330J
RS1/16S330J

R
R
R
R
R

268
269
270
279
281

(B,68 ,37 )
(A,73 ,33 )
(A,73 ,35 )
(A,63 ,25 ) CHIP RESISTOR
(B,19 ,33 )

RS1/16S101J
RS1/16S102J
RS1/16S102J
RS1/16S2201F
RS1/10S0R0J

R
R
R
R
R

284
301
302
303
313

(A,34 ,61 )
(B,89 ,136 )
(B,86 ,136 )
(B,87 ,133 )
(A,80 ,125 )

RS1/16S103J
RS1/10S0R0J
RS1/10S0R0J
RS1/10S0R0J
RS1/16S104J

R
R
R
R
R

314
315
318
321
322

(A,75 ,125 )
(A,80 ,128 )
(A,80 ,126 )
(A,61 ,87 )
(A,73 ,87 )

RS1/16S103J
RS1/16S103J
RS1/16S104J
RS1/16S4R7J
RS1/16S4R7J

R
R
R
R
R

325
326
401
402
403

(A,68 ,87 )
(A,66 ,87 )
(A,82 ,30 )
(B,99 ,14 )
(B,99 ,13 )

RS1/16S4R7J
RS1/16S4R7J
RS1/16S103J
RS1/16S103J
RS1/16S0R0J

R
R
R
R
R

404
411
412
413
414

(A,83 ,25 )
(A,69 ,23 )
(A,70 ,23 )
(A,67 ,23 )
(A,71 ,23 )

RS1/16S102J
RS1/16S1500F
RS1/16S1500F
RS1/16S1500F
RS1/16S1500F

R
R
R
R
R

415
416
421
422
423

(A,73 ,23 )
(A,74 ,23 )
(B,102 ,15 )
(B,99 ,20 )
(B,99 ,21 )

RS1/16S1500F
RS1/16S1500F
RS1/16S0R0J
RS1/16S0R0J
RS1/16S0R0J

A

VKN1319

R
R
R
R
R

8

RS1/16S330J
RS1/16S330J

R 424 (B,99 ,23 )
R 425 (B,99 ,25 )

6

C

D

E

F

RS1/16S0R0J
RS1/16S0R0J

47

XV-GX3
5

B

7

8

1

Mark No.

2

Description

3

Part No.

Mark No.

4

Description

Part No.

R 426 (B,99 ,29 )
R 481 (A,103 ,7 )
R 501 (A,91 ,64 )

RS1/16S0R0J
RS1/16S102J
RS1/16S0R0J

R 909 (A,46 ,125 )
R 910 (A,48 ,128 )
R 911 (A,50 ,128 )

RS1/16S682J
RS1/16S221J
RS1/16S221J

R
R
R
R
R

503
504
505
506
507

(A,92 ,73 )
(A,92 ,74 )
(A,94 ,74 )
(A,101 ,74 )
(A,104 ,74 )

RS1/16S101J
RS1/16S101J
RS1/16S101J
RS1/16S220J
RS1/16S101J

R
R
R
R
R

912
916
917
921
922

(A,53 ,128 )
(B,47 ,128 )
(B,44 ,125 )
(A,106 ,7 )
(A,106 ,8 )

RS1/16S0R0J
RS1/16S223J
RS1/16S223J
RS1/16S0R0J
RS1/16S0R0J

R
R
R
R
R

508
509
511
512
513

(A,104 ,73 )
(A,104 ,72 )
(A,100 ,60 )
(A,97 ,60 )
(A,103 ,59 )

RS1/16S101J
RS1/16S101J
RS1/16S223J
RS1/16S223J
RS1/16S471J

R
R
R
R
R

923 (A,105 ,10 )
924 (A,105 ,11 )
1001(B,107 ,6 )
1002(B,116 ,16 )
1003(B,118 ,16 )

RS1/16S0R0J
RS1/16S0R0J
RS1/10S0R0J
RS1/10S0R0J
RS1/10S0R0J

R
R
R
R
R

514
515
516
517
518

(A,95 ,59 )
(A,99 ,56 )
(A,98 ,56 )
(B,105 ,68 )
(A,101 ,52 )

RS1/16S471J
RS1/16S222J
RS1/16S222J
RS1/16S102J
RS1/16S102J

R
R
R
R
R

519
520
521
522
591

(A,99 ,50 )
(A,111 ,69 )
(A,110 ,53 )
(A,112 ,53 )
(A,83 ,50 )

RS1/16S103J
RS1/16S102J
RS1/16S0R0J
RS1/16S0R0J
RS1/16S0R0J

R
R
R
R
R

592
594
701
702
732

(A,79 ,55 )
(A,80 ,72 )
(A,24 ,137 )
(A,27 ,134 )
(A,25 ,91 )

RS1/16S100J
RS1/16S0R0J
RS1/16S473J
RS1/16S103J
RS1/10S100J

R
R
R
R
R

733
734
735
736
737

(A,25 ,93 )
(A,30 ,89 )
(A,29 ,84 )
(A,32 ,93 )
(A,31 ,83 )

RS1/16S220J
RS1/16S473J
RS1/16S272J
RS1/16S1802F
RS1/16S2702F

R
R
R
R
R

738
739
740
750
751

(A,29 ,82 )
(A,19 ,78 )
(A,29 ,85 )
(A,30 ,99 )
(A,33 ,119 )

RS1/16S1502F
RS1/16S0R0J
RS1/16S0R0J
RS1/16S0R0J
RS1/16S0R0J

R
R
R
R
R

761
762
763
764
801

(A,37 ,114 )
(A,45 ,114 )
(A,44 ,112 )
(A,44 ,110 )
(A,54 ,85 )

RS1/16S0R0J
RS1/16S3902F
RS1/16S334J
RS1/16S334J
RS1/16S471J

R
R
R
R
R

821
822
823
824
851

(A,42 ,83 )
(A,39 ,86 )
(A,36 ,86 )
(A,37 ,86 )
(A,39 ,89 )

RS1/16S103J
RS1/16S473J
RS1/16S153J
RS1/16S103J
RS1/16S473J

R
R
R
R
R

852
853
881
882
901

(A,36 ,89 )
(A,37 ,89 )
(A,39 ,93 )
(A,36 ,93 )
(A,39 ,128 )

RS1/16S103J
RS1/16S103J
RS1/16S473J
RS1/16S103J
RS1/16S0R0J

R
R
R
R
R

902
903
904
905
906

(B,40 ,131 )
(A,43 ,128 )
(A,41 ,128 )
(A,44 ,128 )
(A,42 ,126 )

RS1/16S0R0J
RS1/16S332J
RS1/16S682J
RS1/16S332J
RS1/16S682J

R 907 (A,46 ,128 )
R 908 (A,47 ,128 )

RS1/16S471J
RS1/16S332J

A

B

C

D

E

F

48

CAPACITORS
C
C
C
C
C

101
102
103
104
121

(A,49 ,120 )
(A,73 ,101 )
(A,66 ,116 )
(A,61 ,117 )
(B,61 ,112 )

CEVW101M16
CKSRYB105K10
CKSRYB105K10
CKSRYB105K10
CKSRYB105K10

C
C
C
C
C

131
140
144
145
146

(A,52 ,103 )
(A,60 ,137 )
(A,62 ,99 )
(A,64 ,98 )
(A,60 ,98 )

CKSRYB104K25
CKSRYB105K10
CKSRYB222K50
CKSRYB222K50
CKSRYB222K50

C
C
C
C
C

151
152
153
161
201

(A,68 ,114 )
(A,71 ,114 )
(A,73 ,111 )
(A,58 ,96 )
(A,21 ,52 ) CHIP ELECT.CAPACITOR

CKSRYB103K50
CKSRYB103K50
CKSRYB103K50
CKSRYB102K50
CEVW221M4

C
C
C
C
C

202
203
204
205
206

(A,69 ,64 ) CHIP ELECT.CAPACITOR CEVW221M4
(A,55 ,78 ) CHIP ELECT.CAPACITOR CEVW470M16
(A,52 ,63 )
CKSRYB104K25
(B,52 ,69 )
CKSRYB104K25
(A,47 ,77 ) CHIP ELECT.CAPACITOR CEVW470M16

C
C
C
C
C

207
208
209
210
211

(B,53 ,55 )
(A,48 ,70 )
(A,50 ,70 )
(A,47 ,70 )
(A,46 ,70 )

CKSRYB104K25
CKSRYB222K50
CKSRYB104K25
CKSRYB222K50
CCSRCH560J50

C
C
C
C
C

212
213
214
215
216

(A,44 ,70 )
(A,55 ,63 )
(B,50 ,54 )
(A,55 ,69 ) CHIP ELECT.CAPACITOR
(A,46 ,62 )

CCSRCH560J50
CKSRYB104K25
CKSRYB104K25
CEVW470M16
CKSRYB104K25

C
C
C
C
C

217
219
220
222
223

(A,42 ,62 )
(A,36 ,61 )
(A,31 ,58 )
(A,29 ,53 )
(A,29 ,51 )

CKSRYB104K25
CKSRYB152K50
CKSRYB104K25
CKSRYB104K25
CKSRYB104K25

C
C
C
C
C

224
225
226
227
228

(A,25 ,45 )
(B,34 ,39 )
(B,40 ,39 )
(B,36 ,40 )
(B,39 ,37 )

CKSRYB104K25
CKSRYB104K25
CKSRYB103K50
CCSRCH221J50
CKSRYB104K25

C
C
C
C
C

230
231
232
233
234

(B,37 ,35 )
(B,42 ,35 )
(B,46 ,36 )
(B,49 ,33 )
(B,52 ,33 )

CKSRYB102K50
CKSRYB104K25
CKSRYB104K25
CKSRYB104K25
CKSRYB104K25

3

4

XV-GX3
1

2

5

Mark No.

6

Description

Part No.

7

Mark No.

8

Description

Part No.

C
C
C
C
C

235
236
237
239
240

(B,55 ,35 )
(B,56 ,33 )
(A,65 ,16 ) CHIP ELECT.CAPACITOR
(B,60 ,34 )
(B,59 ,39 )

CKSRYB104K25
CKSRYB104K25
CEVW221M4
CKSRYB104K25
CKSRYB104K25

C
C
C
C
C

416
500
501
503
504

(B,84 ,29 )
(B,95 ,70 )
(A,91 ,60 )
(A,86 ,65 )
(A,93 ,68 )

CKSRYB104K25
CKSRYB105K10
CKSRYB104K25
CEVW101M16
CKSRYB104K25

C
C
C
C
C

241
243
244
245
246

(B,61 ,43 )
(A,61 ,25 )
(A,60 ,25 )
(B,61 ,31 )
(B,63 ,32 )

CKSRYB104K25
CKSRYB105K10
CKSRYB104K25
CKSRYB104K25
CKSRYB104K25

C
C
C
C
C

508
509
511
512
513

(A,104 ,66 )
(A,106 ,62 )
(A,100 ,65 )
(A,95 ,65 )
(A,100 ,58 )

CKSRYB104K25
CEVW100M16
CEVW100M16
CEVW100M16
CKSRYB102K50

C
C
C
C
C

250
251
252
253
254

(B,64 ,36 )
(A,73 ,47 )
(A,73 ,44 )
(B,64 ,44 )
(B,64 ,48 )

CKSRYB103K50
CCSRCH8R0D50
CCSRCH100D50
CKSRYB104K25
CCSRCH391J50

C
C
C
C
C

514
701
711
712
713

(A,97 ,58 )
(A,24 ,131 )
(A,28 ,73 )
(A,35 ,78 )
(A,29 ,66 )

CKSRYB102K50
CKSQYB105K16
CKSRYB105K10
CCSRCH471J50
CKSQYB225K10

C
C
C
C
C

255
256
257
258
259

(B,65 ,53 )
(B,72 ,52 )
(B,60 ,49 )
(A,69 ,49 )
(A,72 ,50 )

CKSRYB474K10
CEVW100M16
CKSRYB104K25
CKSRYB473K50
CKSRYB473K50

C
C
C
C
C

732
733
734
735
736

(A,22 ,113 ) CHIP CERAMIC C.
(A,20 ,105 ) CHIP CERAMIC C.
(A,21 ,100 )
(A,20 ,95 ) CHIP CERAMIC C.
(A,25 ,89 )

DCH1165
DCH1165
CEVW101M16
DCH1165
CKSRYB104K25

C
C
C
C
C

260
265
266
267
268

(B,60 ,50 )
(A,73 ,53 )
(B,60 ,52 )
(A,70 ,53 )
(A,73 ,56 )

CKSRYB104K25
CCSRCH220J50
CKSRYB104K25
CKSRYB102K50
CKSRYB104K25

C
C
C
C
C

737
738
739
751
752

(A,28 ,82 )
(A,24 ,78 ) CHIP CERAMIC C.
(A,21 ,66 )
(A,32 ,119 )
(A,34 ,108 )

CCSRCH121J50
DCH1165
CEVW101M16
CKSRYB105K10
CCSRCH471J50

C
C
C
C
C

269
271
272
273
281

(A,72 ,56 )
(A,70 ,57 )
(A,70 ,58 )
(A,69 ,60 )
(B,18 ,27 ) CHIP ELECT.CAPACITOR

CKSRYB333K16
CKSRYB104K25
CKSRYB104K25
CKSRYB104K25
CEVW221M4

C
C
C
C

753
761
762
801

(A,30 ,108 )
(A,41 ,103 )
(A,40 ,112 )
(A,50 ,83 )

CKSQYB225K10
CEVW101M16
CKSRYB105K10
CKSRYB104K25

C
C
C
C
C

282
283
284
285
286

(B,22 ,31 )
(B,46 ,33 )
(B,33 ,17 )
(B,27 ,17 )
(B,27 ,33 )

CKSRYB105K10
CKSRYB104K25
CKSRYB104K25
CKSRYB104K25
CKSRYB104K25

C
C
C
C
C

287
288
289
290
296

(B,31 ,33 )
(B,34 ,33 )
(B,34 ,40 )
(A,20 ,39 )
(B,34 ,42 )

CKSRYB104K25
CKSRYB104K25
CKSRYB105K10
CKSRYB104K25
CKSRYB102K50

C
C
C
C
C

309
310
343
344
345

(A,71 ,77 ) CHIP ELECT.CAPACITOR CEVW470M16
(A,63 ,77 ) CHIP ELECT.CAPACITOR CEVW470M16
(A,64 ,64 )
CKSRYB105K10
(A,60 ,64 )
CKSRYB105K10
(A,62 ,64 )
CKSRYB105K10

C
C
C
C
C

346
347
371
372
373

(A,63 ,64 )
(A,59 ,64 )
(A,94 ,134 )
(B,94 ,134 )
(A,99 ,127 )

CKSRYB105K10
CKSRYB105K10
CKSRYB104K25
CKSRYB104K25
CEVW101M16

C
C
C
C
C

401
402
404
405
406

(B,90 ,9 )
(B,97 ,11 )
(A,93 ,23 )
(B,84 ,22 )
(B,99 ,16 )

CEVW101M16
CKSRYB104K25
CEVW101M16
CKSRYB104K25
CKSRYB104K25

C
C
C
C
C

411
412
413
414
415

(B,84 ,15 )
(B,84 ,18 )
(B,84 ,21 )
(B,84 ,25 )
(B,84 ,27 )

CKSRYB104K25
CKSRYB105K10
CKSRYB105K10
CKSRYB105K10
CKSRYB104K25

A

B

C

C MAIN ASSY
MISCELLANEOUS
> IC
> IC
> IC
> IC
> IC

11
41
42
51
61

(A,232 ,72 ) IC
(B,218 ,88 ) REGULATOR IC
(A,210 ,103 ) IC
(A,200 ,149 ) REGULATOR IC
(A,200 ,108 ) REGULATOR IC

TA7805S
NJM78M05DL1A
NJM78L08A
TA79012S
TA7812S

IC
IC
> IC
> IC

(B,49 ,200 ) REGULATOR IC
3001(B,80 ,168 ) E-VOL IC
3031(B,108 ,184 ) OP-AMP IC
3301(A,126 ,119 ) AUDIO IC
3303(A,230 ,43 ) PROTECTOR(7A)

NJM78M09DL1A
BD3401KS2
BA4560RF
STK433-070
AEK7021

IC
IC
Q
Q
>Q

5401(B,41 ,38 ) EEPROM
5501(B,66 ,63 ) SYSTEM CONTROL MICON
11 (B,249 ,100 ) TRANSISTOR
12 (A,255 ,104 ) TRANSISTOR
41 (A,200 ,92 ) TRANSISTOR

S-93C46BD0I-J8T1
PDC129A
2SC4081
2SD1858X
2SB1565

> IC 71

> Q 51

Q
Q
>Q
Q
Q
Q
Q
Q
Q

52
53
61
81

(A,305 ,46 ) TRANSISTOR
(B,275 ,13 ) DIGITAL TRANSISTOR
(B,278 ,9 ) CHIP DIGITAL TRANS.
(A,200 ,134 ) TRANSISTOR
(A,309 ,12 ) TRANSISTOR

2101(B,78 ,110 )
2301(A,33 ,120 )
2302(A,31 ,127 )
2303(B,27 ,116 )
2304(B,20 ,117 )

TRANSISTOR
N-FET
N-FET
TRANSISTOR
TRANSISTOR

Q 2351(B,67 ,116 ) CHIP DIGITAL TRANS.
Q 2352(B,57 ,117 ) CHIP TRANSISTOR

6

2SC4081
2SK373
2SK373
DTC114TK
DTC114TK

F

DTA124EUA
RN1901

49
7

E

2SB1565
DTC124EUA
DTA124EUA
2SD2012
2SB1565

XV-GX3
5

D

8

1

Mark No.

2

Description

3

Part No.

Mark No.

4

Description

Part No.

Q 2801(A,11 ,72 ) TRANSISTOR
Q 2802(A,20 ,76 ) TRANSISTOR
Q 2805(A,30 ,101 ) TRANSISTOR

2SC1815
2SC1815
2SC1815

D 2304(A,20 ,108 ) DIODE
D 2305(A,33 ,107 ) DIODE
D 2306(A,10 ,117 ) DIODE

1SS133
1SS133
1SS133

Q
Q
Q
Q
Q

2806(A,30 ,96 )
2901(B,23 ,10 )
2902(B,36 ,22 )
2905(B,45 ,20 )
2906(B,55 ,20 )

2SC2240
DTA124EUA
RN1901
2SB1132
2SB1132

D
D
D
D
D

2307(A,29 ,112 ) DIODE
2901(A,77 ,14 ) DIODE
2902(A,67 ,14 ) DIODE
3301(A,141 ,104 ) DIODE
3302(A,146 ,126 ) DIODE

1SS133
1SS133
1SS133
S5688G
S5688G

Q
Q
Q
Q
Q

3001(B,67 ,207 ) TRANSISTOR
3003(B,146 ,193 ) CHIP DIGITAL TRANS.
3303(B,104 ,115 ) TRANSISTOR
3304(B,112 ,115 ) TRANSISTOR
3305(B,123 ,82 ) TRANSISTOR

IMX9
DTA124EUA
2SD2114K
2SD2114K
2SC4081

D
D
D
D
D

3303(A,141 ,107 )
3304(A,137 ,126 )
3305(A,151 ,104 )
3306(A,137 ,129 )
3307(A,148 ,110 )

S5688G
S5688G
S5688G
S5688G
S5688G

3321(B,147 ,80 ) TRANSISTOR
3322(B,147 ,84 ) TRANSISTOR
3501(A,129 ,173 ) MOS FET
3502(A,129 ,157 ) MOS FET
3503(B,133 ,171 ) TRANSISTOR

2SC4081
2SC4081
2SJ304
2SK2232
2SC4081

D
D
D
D
D

3308(A,136 ,133 ) DIODE
3309(A,125 ,80 ) DIODE
3321(B,128 ,74 ) DIODE
3323(B,151 ,86 ) DIODE
3501(B,134 ,182 ) DIODE

S5688G
1SS133
DAP202K
DAN202K
DAN202K

Q
Q
Q
Q
Q

3504(B,133 ,154 ) TRANSISTOR
3541(B,122 ,61 ) TRANSISTOR
3542(B,102 ,80 ) TRANSISTOR
3603(B,150 ,155 ) CHIP TR (PNP X 2)
3604(B,163 ,157 ) CHIP TR (PNP X 2)

2SA1576A
2SA1576A
2SC4081
UMB1N
UMB1N

D
D
D
D
D

3502(B,128 ,162 )
3503(A,136 ,175 )
3504(A,140 ,153 )
3505(A,136 ,172 )
3506(A,137 ,161 )

DIODE
DIODE
DIODE
DIODE
DIODE

DAP202K
MTZJ36(B)
MTZJ36(B)
1SS133
1SS133

Q
Q
Q
Q
Q

3605(B,153 ,148 )
3606(B,165 ,142 )
3620(B,144 ,188 )
3621(B,161 ,172 )
3622(B,154 ,174 )

TRANSISTOR
TRANSISTOR
CHIP DIGITAL TRANS.
CHIP DIGITAL TRANS.
TRANSISTOR

UMH1N
UMH1N
DTA124EUA
DTA124EUA
2SC4081

D
D
D
D
D

3507(A,136 ,166 )
3508(A,137 ,153 )
3509(A,136 ,178 )
3510(A,130 ,148 )
3511(A,151 ,115 )

DIODE
DIODE
DIODE
DIODE
DIODE

MTZJ18(B)
MTZJ18(B)
MTZJ10(B)
MTZJ10(B)
30PDA20-FC6

Q
Q
Q
Q
Q

3623(B,155 ,180 ) CHIP DIGITAL TRANS.
3625(B,114 ,74 ) CHIP TRANSISTOR
3628(B,160 ,184 ) DIGITAL TRANSISTOR
3629(B,155 ,186 ) DIGITAL TRANSISTOR
3651(B,207 ,218 ) TRANSISTOR

DTA124EUA
HN1C01FU
DTC124EUA
DTC143EUA
DTA124TK

D
D
D
D
D

3512(A,144 ,135 ) DIODE
3541(B,101 ,91 ) DIODE
3542(B,103 ,91 ) DIODE
3543(B,126 ,56 ) DIODE
3601(A,157 ,146 ) DIODE

30PDA20-FC6
1SS355
UDZS7R5(B)
UDZS20(B)
MTZJ7R5(B)

Q
Q
Q
Q
Q

3652(B,194 ,218 ) CHIP TRANSISTOR
3653(B,198 ,210 ) CHIP DIGITAL TRANS.
3654(A,202 ,192 ) TRANSISTOR
5411(B,85 ,104 ) DIGITAL TRANSISTOR
5502(B,108 ,39 ) DIGITAL TRANSISTOR

RN1901
DTA124EUA
2SD2144S
DTA143EUA
DTC143EUA

D
D
D
D
D

3602(A,169 ,161 )
3603(A,148 ,165 )
3604(A,179 ,145 )
3605(A,179 ,138 )
3621(A,145 ,173 )

MTZJ7R5(B)
1SS133
1SS133
1SS133
MTZJ5R1(B)

2SC4081
S1NB60
MTZJ20(B)
DAN217
1SS133

D
D
D
D
D

3622(B,165 ,172 ) DIODE
3623(A,151 ,178 ) DIODE
3624(A,145 ,181 ) DIODE
3625(A,270 ,82 ) DIODE
3626(A,267 ,87 ) DIODE

DAN202K
1SS133
1SS133
1SS133
1SS133

(A,290 ,35 ) DIODE
(A,280 ,35 ) DIODE
(A,301 ,102 ) DIODE
(A,223 ,81 ) DIODE
(A,205 ,83 ) DIODE

D5SBA20(B)
D5SBA20(B)
D5SBA20(B)
MTZJ7R5(C)
MTZJ11(B)

D
D
D
D
D

3651(A,206 ,210 ) DIODE
3652(A,207 ,225 ) DIODE
3653(A,206 ,204 ) DIODE
3654(A,207 ,222 ) DIODE
5501(B,124 ,56 ) DIODE

1SS133
MTZJ3R9(B)
1SS133
1SS133
1SS355

(A,309 ,60 ) DIODE
(A,306 ,60 ) DIODE
(A,309 ,40 ) DIODE
(A,309 ,43 ) DIODE
(A,205 ,153 ) DIODE

S5688G
S5688G
MTZJ27(B)
1SS133
MTZJ15(C)

D
L
L
L
L

5502(B,95 ,56 ) DIODE
2801(A,25 ,86 ) COIL
2802(A,59 ,109 ) RADIAL INDUCTOR
2811(A,48 ,112 ) COIL
2812(A,38 ,112 ) COIL

1SS355
RTD1082
LFEA151J
RTF1004
RTF1004

A

B

Q
Q
>Q
>Q
Q

C

D

TRANSISTOR
CHIP DIGITAL TRANS.
CHIP TRANSISTOR
TRANSISTOR
TRANSISTOR

Q 5503(B,279 ,24 ) TRANSISTOR
(B,231 ,101 ) BRIDGE DIODE
D 12 (A,245 ,108 ) DIODE
D 13 (B,248 ,105 ) DIODE
D 14 (A,270 ,104 ) DIODE

> D 11

E

> D 21
> D 31
> D 41

D 43
D 44
> D 51
> D 52

D 53
D 55
D 57
D
D
D
D
D

F

81 (A,310 ,26 )
82 (A,304 ,22 )
83 (A,309 ,19 )
2101(A,71 ,112 )
2301(A,23 ,111 )

DIODE
DIODE
DIODE
DIODE
DIODE

D 2302(A,17 ,113 ) DIODE
D 2303(A,26 ,106 ) DIODE

S5688G
MTZJ3R6(B)
MTZJ2R0(B)
1SS133
1SS133

DIODE
DIODE
DIODE
DIODE
DIODE

L 3301(A,157 ,71 ) COIL
L 3302(A,144 ,72 ) COIL
L 5501(A,93 ,44 ) AXIAL INDUCTOR
> AN1
(A,228 ,230 ) AC INLET 1P
H 1
(A,230 ,208 ) FUSE CLIP
H 2
H 3

1SS133
1SS133

50

DIODE
DIODE
DIODE
DIODE
DIODE

ATH-059
ATH-059
LAU220J
XKP3084
AKR7001

(A,230 ,187 ) FUSE CLIP
(A,315 ,171 ) FUSE CLIP

AKR7001
AKR7001

3

4

XV-GX3
1

2

5

Mark No.
H 4
H 5
H 6

6

Description

Part No.

(A,315 ,192 ) FUSE CLIP
(A,303 ,176 ) FUSE CLIP
(A,303 ,155 ) FUSE CLIP

H 7
(A,301 ,90 ) FUSE CLIP
H 8
(A,279 ,90 ) FUSE CLIP
JA 3001(A,61 ,230 ) JACK
JA 3301(A,107 ,230 ) SPEAKER TERMINAL 4-P
JA 8801(A,18 ,230 ) JACK
KN1
(A,316 ,225 ) SCREW PLATE
KN3
(A,12 ,31 ) WRAPPING TERMINAL
VR2801(A,20 ,97 ) VR
VR2802(A,10 ,96 ) VR
> RY1
(A,267 ,100 ) RELAY

7

Mark No.

AKR7001
AKR7001
AKR7001
AKR7001
AKR7001
AKB7170
XKE3020
VKB1168
VNE1948
VNF1084
PCP1032
PCP1032
ASR7027

> S 101 (A,303 ,214 ) VOLTAGE SELECTOR AKX7017
> S 102 (A,266 ,214 ) VOLTAGE SELECTOR AKX7017
>T 2
(A,227 ,135 ) STANDBY TRANSFORMER ATT7080

X 5501(A,87 ,56 ) CERAMIC RESONATOR
(10MHz)
> CN1
(A,310 ,118 ) CONNECTOR

ASS7034

> CN2

(A,310 ,133 ) CONNECTOR
CN21 (A,310 ,70 ) CONNECTOR
CN1501(A,115 ,14 ) 25P CONNECTOR
CN2301(A,13 ,114 ) CONNECTOR
CN2302(A,11 ,89 ) CONNECTOR POST

B4P7S-VH
B10PS-VH
VKN1256
B4B-PH
B2B-PH

CN2901(A,80 ,11 ) CONNECTOR
CN3001(A,8 ,157 ) 27P CONNECTOR
CN3051(A,161 ,13 ) CONNECTOR
CN3651(A,211 ,201 ) PLUG(2P)
CN3991(A,186 ,10 ) 12PJUMPER CONNECTOR

52045-1145
VKN1258
52045-0545
KM200SA2
52147-1210

CN5651(A,262 ,11 ) CONNECTOR
CN5701(A,16 ,177 ) CONNECTOR
CN8802(A,39 ,230 ) SOCKET
PCB BINDER
3992PIN JACK(2P)

52045-1745
52045-1145
AKP7045
VEF1040
AKB1233

B2P3S-VH

RESISTORS
R
R
R
R
R

11
12
14
15
16

(B,245 ,100 )
(B,247 ,100 )
(B,252 ,105 )
(B,252 ,101 )
(A,252 ,97 )

RS1/16S222J
RS1/16S223J
RS1/16S102J
RS1/16S103J
RD1/4PU390J

R
R
R
R
R

41
51
55
56
57

(A,204 ,92 )
(A,301 ,53 ) CARBON FILM RESISTOR
(B,269 ,12 )
(B,271 ,12 )

RD1/4PU221J
RD1/2PMF332J
RS1/16S823J
RS1/16S224J
RS1/16S1R0J

R
R
R
R
R

58
61
62
81
82

(B,203 ,135 )
(B,202 ,129 )
(B,304 ,28 )
(A,304 ,16 )

RS1/16S1R0J
RS1/16S473J
RS1/16S100J
RS1/16S103J
RD1/4PU1R0J

R
R
R
R
R

84 (A,288 ,16 )
1501(B,118 ,183 )
1502(B,116 ,190 )
1503(B,115 ,148 )
1504(B,115 ,186 )

RD1/4PU332J
RS1/16S562J
RS1/16S562J
RS1/16S223J
RS1/16S223J

R
R
R
R
R

2101(B,82 ,116 )
2102(B,77 ,116 )
2103(B,75 ,116 )
2104(B,74 ,104 )
2105(B,83 ,110 )

RS1/16S103J
RS1/16S124J
RS1/16S392J
RS1/16S271J
RS1/16S333J

8

Description

Part No.

R
R
R
R
R

2106(B,81 ,106 )
2107(B,73 ,116 )
2108(B,72 ,104 )
2109(B,70 ,104 )
2301(B,33 ,116 )

RS1/16S102J
RS1/16S102J
RS1/16S104J
RS1/16S274J
RS1/16S105J

R
R
R
R
R

2302(B,31 ,130 )
2303(B,50 ,132 )
2304(B,45 ,132 )
2311(B,60 ,154 )
2312(B,70 ,153 )

RS1/16S105J
RS1/16S334J
RS1/16S334J
RS1/16S681J
RS1/16S681J

R
R
R
R
R

2321(B,60 ,150 )
2322(B,72 ,153 )
2323(B,60 ,147 )
2324(B,71 ,149 )
2325(B,63 ,138 )

RS1/16S474J
RS1/16S474J
RS1/16S333J
RS1/16S333J
RS1/16S0R0J

R
R
R
R
R

2326(B,69 ,138 )
2351(B,69 ,116 )
2352(B,64 ,116 )
2353(B,62 ,144 )
2354(B,71 ,143 )

RS1/16S0R0J
RS1/16S104J
RS1/16S223J
RS1/16S0R0J
RS1/16S0R0J

R
R
R
R
R

2401(B,39 ,154 )
2402(B,50 ,151 )
2403(B,39 ,150 )
2404(B,53 ,155 )
2407(B,31 ,152 )

RS1/16S224J
RS1/16S224J
RS1/16S474J
RS1/16S474J
RS1/16S683J

R
R
R
R
R

2408(B,47 ,147 )
2409(B,34 ,138 )
2410(B,41 ,150 )
2801(B,32 ,81 )
2802(B,13 ,78 )

RS1/16S683J
RS1/16S472J
RS1/16S472J
RS1/16S103J
RS1/16S103J

R
R
R
R
R

2803(A,44 ,97 ) CARBON FILM RESISTOR
2805(A,60 ,100 ) CARBON FILM RESISTOR
2809(B,75 ,82 )
2810(B,42 ,100 )
2811(B,38 ,101 )

RD1/2VM4R7J
RD1/2VM161J
RS1/16S102J
RS1/16S473J
RS1/16S102J

R
R
R
R
R

2813(B,19 ,102 )
2814(B,10 ,101 )
2815(A,39 ,88 )
2816(B,32 ,92 )
2821(B,50 ,118 )

RS1/16S102J
RS1/16S102J
RD1/4PU102J
RS1/16S472J
RS1/16S113J

R
R
R
R
R

2822(B,40 ,118 )
2823(B,53 ,115 )
2824(B,43 ,115 )
2901(B,59 ,10 )
2902(B,61 ,10 )

RS1/16S113J
RS1/16S102J
RS1/16S102J
RS1/16S473J
RS1/16S473J

R
R
R
R
R

2903(B,57 ,12 )
2904(B,55 ,12 )
2905(B,49 ,19 )
2906(B,59 ,20 )
2907(A,51 ,24 )

RS1/16S473J
RS1/16S473J
RS1/16S473J
RS1/16S473J
RD1/4PU102J

R
R
R
R
R

2908(A,62 ,24 )
2909(A,21 ,15 )
2910
2911(B,26 ,10 )
2912

RD1/4PU102J
RD1/4PU102J
RS1/16S1R0J
RS1/16S473J
RS1/16S1R0J

R
R
R
R
R

3001(B,71 ,212 )
3002(B,66 ,212 )
3003(B,78 ,209 )
3004(B,64 ,208 )
3005(B,76 ,209 )

RS1/16S224J
RS1/16S224J
RS1/16S182J
RS1/16S182J
RS1/16S472J

6

B

C

D

E

F

51

XV-GX3
5

A

7

8

1

Mark No.

A

B

C

2

Description

3

Part No.

Mark No.

4

Description

Part No.

R
R
R
R
R

3006(B,74 ,209 )
3007(B,80 ,209 )
3011(B,60 ,177 )
3012(B,64 ,173 )
3013(B,58 ,166 )

RS1/16S472J
RS1/16S473J
RS1/16S475J
RS1/16S221J
RS1/16S221J

R
R
R
R
R

3345(A,151 ,72 ) CARBON FILM RESISTOR
3346(A,138 ,72 ) CARBON FILM RESISTOR
3347(B,149 ,64 )
3348(B,142 ,66 )
3355(B,107 ,115 )

RD1/2PMF101J
RD1/2PMF101J
RS1/16S4R7J
RS1/16S4R7J
RS1/16S104J

R
R
R
R
R

3029(B,94 ,177 )
3030(B,91 ,181 )
3031(B,87 ,189 )
3032(B,79 ,192 )
3033(B,82 ,183 )

RS1/16S0R0J
RS1/16S0R0J
RS1/16S153J
RS1/16S184J
RS1/16S184J

R
R
R
R
R

3356(B,122 ,130 )
3361(B,139 ,106 )
3362(B,136 ,106 )
3363(B,136 ,141 )
3364(B,134 ,141 )

RS1/16S104J
RS1/10S2R2J
RS1/10S2R2J
RS1/10S2R2J
RS1/10S2R2J

R
R
R
R
R

3034(B,79 ,188 )
3035(B,109 ,177 )
3036(B,100 ,192 )
3037(B,103 ,187 )
3038(B,98 ,192 )

RS1/16S153J
RS1/16S123J
RS1/16S123J
RS1/16S123J
RS1/16S123J

R
R
R
R
R

3503(B,141 ,181 )
3504(B,133 ,160 )
3505(B,133 ,176 )
3506(B,133 ,150 )
3509(B,133 ,167 )

RS1/16S103J
RS1/16S103J
RS1/16S104J
RS1/16S104J
RS1/16S104J

R
R
R
R
R

3039(B,94 ,190 )
3040(B,96 ,192 )
3041(B,97 ,181 )
3042(B,95 ,181 )
3043(B,96 ,173 )

RS1/16S153J
RS1/16S153J
RS1/16S472J
RS1/16S472J
RS1/16S472J

R
R
R
R
R

3510(B,135 ,150 )
3511(A,141 ,169 )
3512(A,140 ,156 )
3513(B,143 ,168 )
3514(B,142 ,154 )

RS1/16S104J
RD1/4PU101J
RD1/4PU101J
RS1/16S153J
RS1/16S153J

R
R
R
R
R

3044(B,97 ,169 )
3051(B,93 ,163 )
3101(B,57 ,212 )
3102(B,50 ,212 )
3103(B,57 ,205 )

RS1/16S472J
RS1/16S472J
RS1/16S153J
RS1/16S153J
RS1/16S223J

R
R
R
R
R

3541(B,95 ,98 )
3542(B,102 ,85 )
3543(B,98 ,96 )
3544(B,123 ,65 )
3545(B,124 ,61 )

RS1/16S103J
RS1/16S104J
RS1/16S223J
RS1/16S473J
RS1/16S473J

R
R
R
R
R

3104(B,54 ,205 )
3305(B,112 ,136 )
3306(B,120 ,136 )
3307(B,110 ,136 )
3308(B,122 ,136 )

RS1/16S223J
RS1/16S0R0J
RS1/16S0R0J
RS1/16S0R0J
RS1/16S0R0J

R
R
R
R
R

3546(B,126 ,65 )
3547(B,118 ,114 )
3610(B,162 ,148 )
3611(B,157 ,153 )
3612(B,148 ,153 )

RS1/16S472J
RS1/16S0R0J
RS1/16S273J
RS1/16S102J
RS1/16S103J

R
R
R
R
R

3309(B,103 ,128 )
3310(B,124 ,131 )
3311(B,102 ,108 )
3312(B,109 ,107 )
3313(B,118 ,108 )

RS1/16S102J
RS1/16S102J
RS1/16S222J
RS1/16S222J
RS1/16S221J

R
R
R
R
R

3613(B,157 ,149 )
3614(B,150 ,160 )
3615(B,164 ,148 )
3616(B,169 ,144 )
3617(B,169 ,140 )

RS1/16S821J
RS1/16S103J
RS1/16S102J
RS1/16S103J
RS1/16S103J

R
R
R
R
R

3314(B,110 ,111 )
3315(B,104 ,108 )
3316(B,108 ,111 )
3317(B,116 ,97 )
3318(B,117 ,90 )

RS1/16S221J
RS1/16S563J
RS1/16S563J
RS1/16S152J
RS1/16S152J

R
R
R
R
R

3621(A,148 ,173 )
3622(A,151 ,170 )
3623(A,148 ,176 )
3625(A,154 ,165 )
3626(A,267 ,77 )

RD1/4PU223J
RD1/4PU223J
RD1/4PU682J
RD1/4PU272J
RD1/4PU332J

R
R
R
R
R

3319(B,118 ,97 )
3320(B,121 ,92 )
3321(A,138 ,97 ) METAL OXIDE RESISTOR
3322(A,144 ,97 ) METAL OXIDE RESISTOR
3323(B,124 ,88 )

RS1/16S563J
RS1/16S563J
ACN7122
ACN7122
RS1/16S1R0J

R
R
R
R
R

3629(B,163 ,185 )
3630(B,124 ,73 )
3651(A,206 ,213 )
3652(B,210 ,217 )
3653(B,191 ,218 )

RS1/16S273J
RS1/16S103J
RD1/4PU330J
RS1/16S222J
RS1/16S182J

R 3329(B,144 ,92 )
R 3332(B,128 ,88 )
R 3333(B,128 ,84 )

RD1/4MUF470J
RD1/4MUF470J
RS1/16S1R0J
RS1/16S562J
RS1/16S333J

R
R
R
R
R

3654(B,195 ,210 )
3655(B,193 ,205 )
3656(B,193 ,210 )
3991(A,152 ,54 ) METAL OXIDE RESISTOR
3992(A,146 ,52 ) METAL OXIDE RESISTOR

RS1/16S822J
RS1/16S223J
RS1/16S332J
RS3LMF471J
RS3LMF471J

R
R
R
R
R

3334(B,126 ,84 )
3335(B,130 ,84 )
3337(A,140 ,77 ) "RESISTOR (0.1OHM,2W)"
3338(A,140 ,82 ) "RESISTOR (0.1OHM,2W)"
3339(B,143 ,80 )

RS1/16S102J
RS1/16S222J
ACN7112
ACN7112
RS1/16S182J

R
R
R
R
R

5401(B,36 ,32 )
5402(B,48 ,40 )
5411(B,85 ,113 )
5412(B,92 ,101 )
5501(B,94 ,66 )

RS1/16S473J
RS1/16S473J
RS1/16S561J
RS1/16S473J
RS1/16S221J

R
R
R
R
R

3340(B,142 ,86 )
3341(B,145 ,80 )
3342(B,144 ,84 )
3343(B,154 ,69 )
3344(B,141 ,71 )

RS1/16S182J
RS1/16S333J
RS1/16S333J
RS1/16S273J
RS1/16S273J

R
R
R
R
R

5502(B,91 ,66 )
5503(B,98 ,63 )
5504(B,93 ,62 )
5506(B,95 ,62 )
5511(B,80 ,52 )

RS1/16S102J
RS1/16S471J
RS1/16S104J
RS1/16S221J
RS1/16S101J

D

E

> R 3325(A,145 ,101 ) CARBON FILM RESISTOR
> R 3326(A,151 ,127 ) CARBON FILM RESISTOR

F

52

XV-GX3
1

2

3

4

5

Mark No.

6

Description

Part No.

7

8

Mark No.
Description
CAPACITORS

R
R
R
R
R

5512(B,76 ,41 )
5513(B,75 ,37 )
5514(B,74 ,41 )
5515(B,77 ,35 )
5516(B,79 ,35 )

RS1/16S221J
RS1/16S221J
RS1/16S221J
RS1/16S103J
RS1/16S103J

>C 1
>C 5

R
R
R
R
R

5519(B,89 ,37 )
5521(B,78 ,38 )
5522(B,72 ,37 )
5525(B,69 ,41 )
5526(B,67 ,37 )

RS1/16S473J
RS1/16S105J
RS1/16S221J
RS1/16S221J
RS1/16S221J

C
C
C
C
C

R
R
R
R
R

5527(B,66 ,41 )
5528(B,65 ,37 )
5529(B,64 ,41 )
5530(B,62 ,37 )
5531(B,52 ,36 )

RS1/16S221J
RS1/16S221J
RS1/16S221J
RS1/16S221J
RS1/16S105J

R
R
R
R
R

5535(B,61 ,41 )
5537(B,51 ,46 )
5538(B,49 ,46 )
5539(B,47 ,48 )
5540(B,45 ,48 )

R
R
R
R
R

Part No.

(A,223 ,186 ) FILM CAPACITOR
(A,258 ,127 ) CKA (10000P/AC250V)
(A,238 ,97 ) ELECT. CAPACITOR
(A,238 ,70 )
(A,225 ,63 )

ACE7013
ACG7033
CEAT102M25
CEAT1R0M50
CEAT100M50

14
15
21
22
31

(B,221 ,73 )
(A,265 ,33 ) ELECT. CAPACITOR
(A,265 ,53 ) ELECT. CAPACITOR
(A,245 ,33 )

CKSRYB103K50
CKSRYB102K50
CEAT222M63
CEAT222M63
CEAT472M35

C
C
C
C
C

32
33
34
35
36

(A,245 ,53 )
(B,280 ,41 )
(B,278 ,41 )
(B,277 ,49 )
(B,277 ,56 )

CEAT472M35
XCG3008
XCG3008
XCG3008
XCG3008

RS1/16S221J
RS1/16S472J
RS1/16S822J
RS1/16S221J
RS1/16S221J

C
C
C
C
C

41
42
43
44
47

(A,254 ,73 ) ELECT. CAPACITOR
(B,224 ,90 )
(A,225 ,85 ) ELECT. CAPACITOR
(A,208 ,93 )
(A,207 ,87 ) ELECT. CAPACITOR

CEAT682M25
CKSRYB473K50
CEAT470M25
CEAT1R0M50
CEAT470M25

5541(B,43 ,48 )
5542(B,41 ,48 )
5543(B,45 ,56 )
5544(B,48 ,36 )
5545(B,50 ,40 )

RS1/16S221J
RS1/16S221J
RS1/16S221J
RS1/16S123J
RS1/16S103J

C
C
C
C
C

51
53
54
56
57

(A,299 ,62 ) ELECT. CAPACITOR
(A,301 ,38 ) ELECT. CAPACITOR
(A,297 ,48 ) ELECT. CAPACITOR
(B,204 ,150 )
(A,209 ,154 )

CEAT101M63
CEAT330M50
CEAT220M50
CKSRYB473K50
CEAT100M50

R
R
R
R
R

5546(B,52 ,40 )
5547(B,45 ,60 )
5548(B,43 ,56 )
5549(B,43 ,60 )
5550(B,40 ,55 )

RS1/16S103J
RS1/16S221J
RS1/16S221J
RS1/16S221J
RS1/16S221J

C
C
C
C
C

61
64
65
71
73

(A,208 ,108 )
(A,208 ,117 ) ELECT. CAPACITOR
(A,208 ,148 )
(A,54 ,197 )
(B,45 ,202 )

CEAT1R0M50
CEAT220M50
CEAT100M50
CEAT1R0M50
CKSRYB104K16

R
R
R
R
R

5551(B,51 ,73 )
5552(B,53 ,73 )
5555(B,55 ,81 )
5556(B,57 ,81 )
5558(B,61 ,82 )

RS1/16S221J
RS1/16S221J
RS1/16S221J
RS1/16S221J
RS1/16S221J

C
C
C
C
C

74 (A,41 ,199 ) ELECT. CAPACITOR
81 (A,301 ,28 ) ELECTR.CAPACITOR
82 (B,267 ,9 )
1501(B,129 ,26 )
1502(B,111 ,22 )

CEAT470M25
CEAT102M10
CKSRYB224K16
CKSRYB104K16
CKSRYB104K16

R
R
R
R
R

5559(B,63 ,82 )
5563(A,85 ,75 )
5564(B,85 ,71 )
5565(B,87 ,71 )
5566(B,80 ,79 )

RS1/16S221J
RD1/4PU221J
RS1/16S221J
RS1/16S221J
RS1/16S221J

C
C
C
C
C

1503(B,142 ,27 )
1505(A,127 ,28 ) ELECT. CAPACITOR
1506(A,109 ,23 ) ELECT. CAPACITOR
1509(B,115 ,182 )
1510(B,114 ,152 )

CKSRYB104K16
CEAT102M16
CEAT470M25
CCSRCH271J50
CCSRCH271J50

R
R
R
R
R

5567(B,82 ,85 )
5568(B,82 ,79 )
5572(B,42 ,11 )
5580(B,293 ,24 )
5581(B,284 ,25 )

RS1/16S221J
RS1/16S221J
RS1/16S153J
RS1/16S102J
RS1/16S103J

C
C
C
C
C

2101(B,79 ,116 )
2102(B,83 ,106 )
2103(A,78 ,104 ) ELECT. CAPACITOR
2105(A,75 ,111 )
2106(B,68 ,104 )

CKSRYB103K50
CKSRYB182K50
CEAT220M50
CEAT100M50
CKSRYB334K10

R
R
R
R
R

5582(B,282 ,25 )
5583(B,213 ,21 )
5584(B,114 ,41 )
5585(B,112 ,41 )
5586(B,121 ,55 )

RS1/16S102J
RS1/16S103J
RS1/16S473J
RS1/16S222J
RS1/16S124J

C
C
C
C
C

2301(B,31 ,116 )
2302(B,33 ,130 )
2303(B,48 ,132 )
2304(B,45 ,136 )
2305(A,50 ,137 )

CCSRCH100D50
CCSRCH100D50
CKSRYB821K50
CKSRYB821K50
CEAT100M50

R
R
R
R
R

5587(B,119 ,55 )
5653(B,233 ,8 )
5715(B,21 ,180 )
8821(B,27 ,209 ) CHIP RESISTOR
8832(B,36 ,211 ) CHIP RESISTOR

RS1/16S224J
RS1/16S100J
RS1/16S224J
RS1/16S75R0F
RS1/16S75R0F

C
C
C
C
C

2306(A,50 ,143 )
2321(A,63 ,148 )
2322(A,73 ,150 )
2325(A,64 ,155 )
2326(A,71 ,156 )

R
R
R
R

8842(B,42 ,211 )
8853(B,22 ,209 )
8863(B,11 ,210 )
8873(B,15 ,209 )

RS1/16S75R0F
RS1/16S75R0F
RS1/16S75R0F
RS1/16S75R0F

C
C
C
C

2401(A,36 ,154 ) FILM CAPACITOR
2402(A,47 ,151 ) FILM CAPACITOR
2405(B,37 ,148 )
2406(B,45 ,149 )

CHIP RESISTOR
CHIP RESISTOR
CHIP RESISTOR
CHIP RESISTOR

C 11
C 12
C 13

CHIP CAPACITOR
CHIP CAPACITOR
CHIP CAPACITOR
CHIP CAPACITOR

FILM CAPACITOR
FILM CAPACITOR
ELECT. CAPACITOR
ELECT. CAPACITOR

6

B

C

D

E

CEAT100M50
CQMBA682J50
CQMBA682J50
CEAT3R3M50
CEAT3R3M50
CQMBA333J50
CQMBA333J50
CKSRYB221K50
CKSRYB221K50

F

53

XV-GX3
5

A

7

8

1

Mark No.

A

B

C

D

E

F

2

Description

3

Part No.

Mark No.

4

Description

Part No.

C 2407(B,35 ,149 )

CKSRYB221K50

C 3060(A,88 ,145 )

CEAT100M50

C
C
C
C
C

2408(B,43 ,150 )
2409(A,32 ,134 )
2410(A,38 ,136 )
2801(A,25 ,81 )
2802(A,33 ,77 )

CKSRYB221K50
CEAT100M50
CEAT100M50
CQMA123J50
CQMA682J50

C
C
C
C
C

3101(B,55 ,212 )
3102(B,52 ,212 )
3107(A,123 ,192 )
3108(A,122 ,186 )
3301(A,111 ,140 )

CKSRYB221K50
CKSRYB221K50
CEAT100M50
CEAT100M50
CEAT2R2M50

C
C
C
C
C

2803(A,29 ,81 )
2804(A,16 ,78 )
2805(A,48 ,100 ) ELECT. CAPACITOR
2807(A,40 ,103 ) ELECT. CAPACITOR
2808(A,20 ,91 ) PPS CAPACITOR

CQMA472J50
CQMA472J50
CEAT330M50
CEAT470M25
CQHA822J2A

C
C
C
C
C

3302(A,117 ,140 )
3305(A,103 ,120 )
3306(A,110 ,120 )
3307(B,118 ,103 )
3308(B,116 ,87 )

CEAT2R2M50
CEAT2R2M50
CEAT2R2M50
CKSRYB102K50
CKSRYB102K50

C
C
C
C
C

2809(B,26 ,100 ) CHIP CAPACITOR
2810(A,39 ,93 ) ELECT. CAPACITOR
2811(B,50 ,114 )
2812(B,40 ,114 )
2813(A,48 ,119 )

ACG7058
CEAT330M50
CCSRCH221J50
CCSRCH221J50
CQMA152J50

C
C
C
C
C

3309(B,122 ,97 )
3310(B,123 ,92 )
3311(B,120 ,97 )
3312(B,119 ,92 )
3313(A,114 ,101 )

CCSRCH470J50
CCSRCH470J50
CCSRCH8R0D50
CCSRCH8R0D50
CEAT100M50

C
C
C
C
C

2814(A,38 ,119 )
2815(A,25 ,133 )
2816(A,39 ,129 )
3001(B,69 ,212 )
3002(B,64 ,212 )

CQMA152J50
CEAT1R0M50
CEAT1R0M50
CKSRYB471K50
CKSRYB471K50

C
C
C
C
C

3314(A,113 ,88 )
3315(A,146 ,93 )
3316(A,140 ,142 )
3317(A,157 ,112 ) ELECT. CAPACITOR
3318(A,158 ,119 ) ELECT. CAPACITOR

CEAT100M50
CEAT221M50
CEAT221M50
CEATR22M50
CEATR22M50

C
C
C
C
C

3003(A,125 ,199 )
3004(A,119 ,198 )
3013(A,66 ,135 )
3014(A,60 ,135 )
3019(A,58 ,173 )

CEAT100M50
CEAT100M50
CEAT100M50
CEAT100M50
CEAT4R7M50

C
C
C
C
C

3320(A,114 ,82 ) ELECT. CAPACITOR
3323(B,153 ,64 )
3324(B,140 ,66 )
3325(B,151 ,66 )
3326(B,147 ,66 )

CEAT470M25
CKSRYB223K50
CKSRYB223K50
CKSRYB223K50
CKSRYB223K50

C
C
C
C
C

3020(B,67 ,179 )
3021(A,64 ,180 ) ELECT. CAPACITOR
3022(B,53 ,177 )
3023(A,58 ,180 ) ELECT. CAPACITOR
3024(A,67 ,184 )

CKSRYB471K50
CEAT470M25
CKSRYB102K50
CEAT470M25
CEAT470M25

C
C
C
C
C

3327(B,113 ,215 ) CHIP CAPACITOR
3328(B,100 ,215 ) CHIP CAPACITOR
3541(B,92 ,97 )
3601(A,145 ,154 )
3602(A,164 ,152 )

XCG3008
XCG3008
CKSRYB103K50
CEAT1R0M50
CEAT1R0M50

C
C
C
C
C

3025(B,105 ,173 )
3026(B,112 ,185 )
3027(B,75 ,194 )
3031(B,89 ,189 )
3032(B,77 ,192 )

CKSRYB104K16
CKSRYB104K16
CKSRYB471K50
CKSRYB563K16
CKSRYB563K16

C
C
C
C
C

3622(A,158 ,166 ) ELECT. CAPACITOR
3623(A,122 ,74 )
3624(A,161 ,179 )
3651(A,202 ,204 ) ELECT. CAPACITOR
3652(A,202 ,211 ) ELECT. CAPACITOR

CEAT2R2M2A
CEAT471M6R3
CEAT100M50
CEAT470M25
CEAT470M25

C
C
C
C
C

3033(B,84 ,183 )
3034(B,77 ,188 )
3035(A,103 ,182 )
3036(A,84 ,188 )
3039(B,107 ,177 )

CKSRYB563K16
CKSRYB563K16
CEAT100M50
CEAT100M50
CCSRCH181J50

C
C
C
C
C

3653(A,202 ,218 ) ELECT. CAPACITOR
5401(B,46 ,36 )
5402(B,46 ,40 )
5411(A,89 ,102 ) ELECT. CAPACITOR
5501(B,78 ,49 )

CEAT101M25
CKSRYB104K16
CCSRCH470J50
CEAT220M50
CKSRYB104K16

C
C
C
C
C

3040(B,102 ,192 )
3041(A,88 ,183 )
3042(A,93 ,185 )
3043(B,96 ,177 )
3044(B,93 ,181 )

CCSRCH181J50
CEAT100M50
CEAT100M50
CKSRYB683K16
CKSRYB683K16

C
C
C
C
C

5504(B,80 ,38 )
5505(B,50 ,36 )
5509(B,77 ,31 )
5510(B,79 ,31 )
5581(A,288 ,26 )

CKSRYB103K50
CCSRCH101J50
CKSRYB103K50
CKSRYB103K50
CEAT1R0M50

C
C
C
C
C

3045(A,101 ,169 )
3046(A,99 ,176 )
3047(B,94 ,173 )
3048(B,93 ,169 )
3049(B,92 ,173 )

CEAT100M50
CEAT100M50
CKSRYB105K10
CKSRYB105K10
CKSRYB104K16

C
C
C
C
C

5582(B,97 ,67 )
5583(A,111 ,36 )
5585(B,110 ,41 )
5586(A,81 ,46 )
5587(B,85 ,44 )

CCSRCH101J50
CEAT100M50
CKSRYB103K50
CEAT101M10
CKSRYB103K50

C
C
C
C
C

3050(B,95 ,169 )
3051(B,98 ,165 )
3052(B,97 ,162 )
3053(B,95 ,163 )
3054(A,91 ,157 ) ELECT. CAPACITOR

CKSRYB104K16
CKSRYB222K50
CKSRYB222K50
CKSRYB105K10
CEATR33M50

C
C
C
C
C

5588(B,115 ,37 )
5589(A,116 ,62 )
5705(B,19 ,183 )
5706(B,21 ,193 )
5708(B,31 ,194 )

CKSRYB104K16
CEAT1R0M50
CKSRYB102K50
CKSRYB104K16
CKSRYB102K50

C
C
C
C

3055(A,60 ,198 )
3056(A,52 ,189 )
3057(A,153 ,24 )
3059(A,84 ,150 )

CEAT100M50
CEAT100M50
CEAT100M50
CEAT100M50

C
C
C
C

5709(B,29 ,194 )
8822(B,27 ,213 )
8831(A,39 ,205 ) ELECT. CAPACITOR
8851(A,21 ,200 ) ELECT. CAPACITOR

CKSRYB103K50
CCSRCH470J50
CEAT102M6R3
CEAT102M6R3

54

XV-GX3
1

2

3

4

5

Mark No.

6

Description

Part No.

C 8852(B,24 ,213 )

CCSRCH470J50

C
C
C
C
C

CEAT471M6R3
CCSRCH470J50
CEAT471M6R3
CCSRCH470J50
CEAT102M6R3

8861(A,9 ,207 )
8862(B,10 ,214 )
8871(A,9 ,200 )
8872(B,14 ,213 )
8881(A,30 ,203 ) ELECT. CAPACITOR

7

Mark No.

D DISPLAY ASSY
MISCELLANEOUS
IC
IC
Q
D
D

5901(B,165 ,81 )
5902(A,125 ,82 )
5981(B,268 ,90 )
5981(A,274 ,82 )
5982(A,299 ,82 )

FL DRIVER IC
REMOTE RECEIVER UNIT
TRANSISTOR
LED(BLUE)
LED(BLUE)

PT6315
RPM7140-H9
2SC4081
SLR-343BBT(GHJ)
SLR-343BBT(GHJ)

D
L
L
V
S

5983(B,274 ,87 ) DIODE
5901(A,134 ,78 ) AXIAL INDUCTOR
5902(A,184 ,76 ) AXIAL INDUCTOR
5901(A,137 ,69 ) FL TUBE
5961(A,290 ,115 ) SWITCH

1SS355
LAU220J
LAU100J
AAV7109
VSG1024

S
S
S
S
S

5962(A,128 ,49 )
5963(A,128 ,24 )
5964(A,152 ,49 )
5965(A,172 ,49 )
5966(A,192 ,49 )

SWITCH
SWITCH
SWITCH
SWITCH
SWITCH

VSG1024
VSG1024
VSG1024
VSG1024
VSG1024

S
S
S
S
S

5967(A,221 ,49 )
5968(A,318 ,82 )
5969(A,285 ,49 )
5970(A,252 ,82 )
5971(A,288 ,82 )

SWITCH
SWITCH
SWITCH
SWITCH
ROTARY ENCODER

VSG1024
VSG1024
VSG1024
VSG1024
XSX3007

CN5901(A,211 ,109 ) CONNECTOR
PCB BINDER
5901FL SPACER(CR)

RS1/16S221J
RS1/16S221J
RS1/16S221J
RS1/16S823J
RS1/16S470J

R
R
R
R
R

5954(B,130 ,94 )
5962(B,129 ,30 )
5963(B,248 ,84 )
5964(B,168 ,50 )
5965(B,185 ,55 )

RS1/16S101J
RS1/16S102J
RS1/16S182J
RS1/16S562J
RS1/16S332J

R
R
R
R
R

5966(B,217 ,50 )
5967(B,318 ,87 )
5968(B,285 ,53 )
5969(B,257 ,78 )
5971(B,273 ,97 )

RS1/16S272J
RS1/16S102J
RS1/16S122J
RS1/16S152J
RS1/16S103J

R
R
R
R
R

5972(B,279 ,97 )
5973(B,275 ,97 )
5974(B,277 ,97 )
5981(B,263 ,90 )
5982(B,272 ,91 )

RS1/16S103J
RS1/16S123J
RS1/16S273J
RS1/16S102J
RS1/10S221J

5907(A,243 ,60 ) ELECT. CAPACITOR
5911(B,134 ,82 )
5912(B,136 ,74 )
5913(A,143 ,59 )
5915(B,171 ,90 )

C
C
C
C
C

5916(B,182 ,81 )
5917(B,180 ,77 )
5918(A,201 ,55 ) ELECT. CAPACITOR
5920(B,151 ,91 )
5921(B,154 ,91 )

CKSRYB223K50
CKSRYB223K50
CEJQ470M35
CCSRCH221J50
CCSRCH221J50

C
C
C
C
C

5922(B,152 ,91 )
5951(B,129 ,76 )
5952(A,123 ,90 )
5971(B,281 ,96 )
5981(B,278 ,87 )

CCSRCH221J50
CKSRYB223K50
CEJQ470M6R3
CKSRYB223K50
CKSRYB103K50

IC
IC
D
L
J

3901(B,35 ,147 ) OP-AMP IC
3921(B,42 ,181 ) ECHO IC
3921(B,31 ,167 ) DIODE
3921(A,30 ,193 ) AXIAL INDUCTOR
3992(A,24 ,65 ) JUMPER WIRE 12P

JA 3902(A,55 ,117 ) JACK
KN3991(A,15 ,82 ) WRAPPING TERMINAL
VR3901(A,47 ,139 ) VARIABLE( 10K-X1)
CN3921(A,34 ,210 ) 5P CONNECTOR
3991JACK
399212P CABLE HOLDER
3901JACK

B

BA4560RF
M65855FP
UDZS5R1(B)
LAU100J
D20PYY1225E
RKN1004
VNF1084
ACS7042
52044-0545
AKN7003

R
R
R
R
R

3901(B,49 ,106 )
3902(B,46 ,106 )
3905(B,41 ,155 )
3906(B,33 ,139 )
3907(B,39 ,155 )

RS1/16S332J
RS1/16S332J
RS1/16S103J
RS1/16S104J
RS1/16S473J

R
R
R
R
R

3908(B,37 ,155 )
3909(B,44 ,153 )
3910(B,40 ,163 )
3911(B,33 ,155 )
3921(B,41 ,189 )

RS1/16S332J
RS1/16S332J
RS1/16S152J
RS1/16S123J
RS1/16S153J

R
R
R
R
R

3922(B,43 ,189 )
3923(B,45 ,189 )
3924(B,36 ,172 )
3925(B,41 ,172 )
3926(B,46 ,172 )

RS1/16S472J
RS1/16S123J
RS1/16S124J
RS1/16S103J
RS1/16S822J

R 3927(B,49 ,189 )
R 3928(B,48 ,172 )
R 3929(B,38 ,198 )

RS1/16S123J
RS1/16S123J
RS1/10S681J

D

E

CAPACITORS

CEJQ470M35
CKSRYB223K50
CKSRYB223K50
CEJQ470M6R3
CKSRYB103K50

6

C

51048-1200
AKN7003

C
C
C
C
C

3901(A,34 ,135 )
3902(B,52 ,102 )
3903(B,41 ,117 )
3904(B,37 ,99 )
3905(B,34 ,99 )

CEJQ2R2M50
CCSRCH101J50
CCSRCH101J50
CKSRYB103K50
CKSRYB104K16

C
C
C
C
C

3908(B,35 ,139 )
3910(A,41 ,137 )
3911(A,41 ,151 )
3912(A,51 ,152 )
3913(B,48 ,153 )

CCSRCH331J50
CEAT2R2M50
CEAT2R2M50
CEAT470M16
CKSRYB104K16

C 3914(B,46 ,153 )
C 3916(A,44 ,164 )
C 3917(B,35 ,155 )

CCSRCH101J50
CEAT2R2M50
CKSRYB122K50

F

55

XV-GX3
5

A

RESISTORS

CAPACITORS
C
C
C
C
C

Part No.

MISCELLANEOUS

RESISTORS
5901(B,151 ,88 )
5902(B,154 ,88 )
5903(B,152 ,88 )
5904(B,158 ,88 )
5951(B,126 ,94 )

Description

E MIC ASSY

52045-1745
VEF1040
AEB7091

R
R
R
R
R

8

7

8

1

Mark No.

A

Description

3

4

3

4

Part No.

C 3919(B,29 ,155 )
C 3922(A,43 ,193 ) ELECT. CAPACITOR

CKSRYB104K16
CEATR47M50

C
C
C
C
C

3923(B,39 ,190 )
3924(B,47 ,189 )
3925(A,32 ,188 ) ELECT. CAPACITOR
3926(B,46 ,194 )
3927(A,49 ,159 )

CKSRYB103K50
CKSRYB103K50
CEAT220M25
CKSRYB473K50
CEAT4R7M50

C
C
C
C
C

3929(B,35 ,172 )
3930(B,39 ,172 )
3931(B,44 ,172 )
3932(B,51 ,175 )
3933(A,37 ,168 )

CKSRYB104K16
CKSRYB103K50
CKSRYB472K50
CKSRYB123K50
CEAT101M16

C 3993(B,36 ,90 )
C 3995(B,42 ,73 )
C 3996(B,41 ,67 )

B

2

CKSRYB104K16
CKSRYB103K50
CKSRYB103K50

C

D

E

F

56

XV-GX3
1

2

5

6

7

8

6. ADJUSTMENT
6.1 DECK SECTION
6.1.1 ADJUSTMENT CONDITION

A

7 Adjustment Condition
(1) The ground at the time of adjustment shall be JA3001(GND)
(Refer to Fig. 6–2).
(2) Clean the heads and demagnetize them using a head eraser.
(3) Set the measurement level to 0 dBV = 1 Vrms.
(4) Use the specified tape for adjustment. Use the labeled (A) side
of the test tape.
NCT–111 or STD-301
: For Tape Speed adjustment
NCT-112 or STD-331E : For Playback adjustment
STD–630 or STD-631
: Normal blank tape
* As the reference recording level is 250nwb/m for STD-331E,
the recording level will be higher by 4 dB for STD-331B
(160nwb/m).
When adjusting, pay carefull attention to the type of tape used.

7 List of Adjustments
¶ Playback Section
(1) Tape Speed Confirmation
(2) Head Azimuth Adjustment
B

¶ Recording Section
(1) Recording Bias Adjustment

(5) Provide yourself with the following measuring devides:
÷ AC millivoltmeter
÷ Low-frequency oscillator
÷ Attenuator
÷ Oscilloscope
(6) Adjust both right and left channels unless other wise specified.
(7) Warm up the unit for several minutes before adjustment. In
particular, be sure to warm up the unit in the REC/PLAY mode
for 3 to 5 minutes before starting recording/playback frequency
characteristics adjustment.
(8) Always follow the indicated adjustment order.
Otherwise, a complete adjustment may not be achieved.

C

D

0 dB

30s

0 dB: 315 Hz, 250 nwb/m

315 Hz

30 s

30 s

6.3 kHz

10 kHz

30 s

10s

10s .......................................................................................................... 10s
–20 dB
12.5
6.3
500 250 125
14 kHz kHz 10 kHz 8 kHz kHz 4 kHz 2 kHz 1 kHz Hz
63
Hz
40
Hz
Hz
Hz

315 Hz

Fig. 6-1 Test Tape NCT– 112 ( STD-331E)
E

F

57

XV-GX3
5

6

7

8

1

2

3

4

6.1.2 PLAYBACK and RECORDING SECTION
7
A

Playback Section

(1) Tape Speed Confirmation
No.
1

Mode
PLAY

Input Signal/Test Tape
NCT-111 (3kHz)
or
STD-301 (3kHz)

Adjustment Points
ADJ. VR on
CASSETTE MECHA
(Refer to Fig. 6-3)

Measurement Points

Adjustment Value

LINE OUT R (JA3001)
(MAIN ASSY)

3000 Hz

+10
–10

Hz

Remarks
FWD adjustment
REV Confirmation
+40
( 3000 Hz –40 Hz)

(2) Head Azimuth Adjustment
¶ This unit is equipped with auto tape selector.
¶ Do not switch between forward and reverse operation with the screwdriver inserted.
B

No.

Mode

1

PLAY

Input Signal/Test Tape
NCT-112 or STD-331E

7

(Playback: 10 kHz, –20 dB)

Measurement
Points

Adjustment Points
Head azimuth
adjustment Screw
(Refer to Fig. 6-3)

Adjustment
Value

LINE OUT L (JA3001)
Max. Playback
LINE OUT R (JA3001)
signal level
(MAIN ASSY)

Remarks
After adjustment, apply silicon
bond to the head azimuth
adjustment screw.

Recording Section

(1) Recording Bias Adjustment
¶ After the adjustment, caution should be exercised so as not to become under bias by checking the distortion rate.
C

No.

Mode

Input Signal/Test Tape

Adjustment Points

1

REC/
PAUSE

Input a 315Hz signal to the LINE IN terminal. ∗

Input signal level

REC =
PLAY

Load the STD–630 or 631 test tape
and record / playback the 315Hz
and 10KHz signals.
(see the Note below)

2

L ch

VR2801

R ch

VR2802

Measurement
Points

Adjustment
Value

Remarks

–23.7 dBV
LINE OUT L (JA3001)
LINE OUT R (JA3001) Repeat adjustment until playback level of
(MAIN ASSY)
the 10kHz signal is within 0dBV ±0.5dB
from that of the 315Hz signal.

Note: Set the 10kHz input signal level to the same value as the 315Hz input signal level of step 1.

D

E

F

58

XV-GX3
1

2

3

4

5

6

MAIN ASSY

7

8

C

A

JA3001 (LINE OUT)
VIDEO

AUDIO

JA

NP

C8881

C8851

C8861

W415

W136

W347

W420
C3036

W348

C3019

W127
X5701

CONTACT SIDE

W309

W340

GNDA

W342
W341
C2401

W349

C3021

EVOLCLK

EVOLDATA

C

C3041

W389

Vref

W388

C3024

C3056

C3023

C5718
W135

B

W394

GNDA W418

W417

C71

W383

W381

W384

C5704

W380

W379
W343

W386

C5721

1
11

W416

C3055

W414

C8871

CN5701

P

C3997

C74

W339

JA3992

W419

JA3001

W421

C8831

CN8802
JA8801

C305
C2326

C2325

27

C

C2402
C3059

VR2402

W311

C2306
C2323

MECHANISM UNIT

C2324

W313

VR2401

C2322

W312

CN3001

W308
C2321

C3060

W310

123.0mm

C2409

C3529

C2305
C2816

VR2301

VR2302

W287
W286

W290

CONTACT SIDE

W267

D2303

L2811

W288
L2101

W289

C3524

W218

C2801

W269

C2103
W226

PB/XREC

W225 XBEATCUT

W224

BIAS

W268

W223

W222

W221

XPROTECT

W227

R5507 W229

W220

1

R2815

C2808

OPEN SIDE

C2810
L2801

W233

R2805

R2803

W231

C2805
Q2806

W228 XSYSMUTE
C5411

W266

Q2805
VR2801

D2102

D
W265
C2807

D2101
C2105

W263

VR2802

CN2302

W270

L2802
D2305

D2304

D2301

C2813

L2812

D2307

W264

OPEN SIDE

123.0mm

4

CN2301

1

Cassette
Mechanism
Section
(Side View)

C2814

Q2301

D2302

D2306

Front Side

C3013

C2410

Q2302

1

Tape Speed
ADJ. VR

C3014

C2815

W230

Q2802
Q2801

PRINT SIDE

C2803

C2804

W232
R5563

C2802

E

FWD Azimuth
Adjustment Screw

BIAS

REV Azimuth
Adjustment Screw

VR2802
(Rch)

VR2801
(Lch)

Fig. 6-2 Adjustment and Measurement Points
F

59

XV-GX3
5

6

7

8

1

2

3

4

6.2 DVD SECTION
6.2.1 ADJUSTMENT ITEMS AND LOCATION

Adjustment Items

Adjustment Points (Mechanism Part)

A

[Mechanism Part]

Cautions: After adjustment, adjustment screw locks with the
Screw tight.

1 Tangential and Radial Height Coarse Adjustment
2 DVD Error Rate Adjustment

1 2
Tangential
adjustment
screw

[Electrical Part]

1 2
Radial
adjustment
screw

Electrical adjustments are not required.
B

C

D

6.2.2 JIG AND MEASURING INSTRUMENTS

E

Screwdriver (large)

Screwdriver (medium)

TV monitor

Test mode remote control
unit (GGF1381)

Screw tight
(GYL1001)
F

Precise screwdriver

DVD test disc
(GGV1025)

60

Soldering iron

XV-GX3
1

2

3

4

5

6

7

8

6.2.3 NECESSARY ADJUSTMENT POINTS

When

Adjustment Points
A

Exchange Parts of Mechanism
Mechanical ~, Ÿ
point

Exchange the 05SD Pickup Assy

∗ After adjustment, screw locks
with the Screw tight.

Electric
point
Mechanical
point

Exchange the Traverse Mechanism
Assy-S

B

Electric
point
∗ After adjustment, screw locks
with the Screw tight.

Mechanical Ÿ
point

Exchange the Spindle Motor

Electric
point
C

Exchange PCB Assy
Mechanical
point

Exchange PC Board

LOAB and DVDM ASSYS

Electric
point
D

E

F

61

XV-GX3
5

6

7

8

1

2

3

4

6.2.4 TEST MODE

A

POWER ON

POWER

B

ON

DISC SET

OPEN/CLOSE
(Player)


OPEN/CLOSE

DVD disc

(Player)

C

TEST MODE: PLAY
CHECK
DVD, CD


ESC

Press the play key
(
) of the normal
remote control unit.

D

An address is displayed

TEST

GGF1381
Test mode
remote control
unit

DSC - &&&

Notes:
• After going into test mode, if you play back the disc, "DISC-NON" is displayed.
• The video signal and the audio signal are outputted during the test mode.
• The SKIP key and the SCAN key are effective during the test mode.
E

TEST MODE: OFF
ESC

POWER
OR
F

GGF1381
Test mode
remote control
unit

OFF

62

XV-GX3
1

2

3

4

5

6

7

8

6.2.5 MECHANISM ADJUSTMENT

A

1 Tangential and Radial Height Coarse Adjustment
START
05SD Pickup Assy

• Remove the 05SD Pickup Assy from the Traverse Mechanism Assy-S.
• Remove the joint and the joint spring of the 05SD Pickup Assy.

Note:
Before removing the flexible cable for the
pickup, soldering of the pickup circuit is
necessary.
For details, see "7.1.10 DISASSEMBLY".

B

Joint
Joint Spring

• Pass through the guide shaft to a new 05SD Pickup Assy.
• Attach it to the Traverse Mechanism Assy-S.

05SD Pickup Assy
C

Guide Shaft

D

• Put the joint between the Tangential (or Radial) adjustment screw and the mechanism base
and turn each screw to adjust the height.
(Refer to "6.2.1 ADJUSTMENT ITEMS AND LOCATION".)

Joint

7.5mm
Mechanism base
E

• Attach the Traverse Mechanism Assy-S to the 05 LOADER Assy.
• Turn it over and attach the joint and the joint spring.
• Arrange the flexible cables.
(Refer to "7.1.10 DISASSEMBLY".)

F

63

XV-GX3
5

6

7

8

1

2

3

2 DVD Error Rate Adjustment

A

4

• Play the DVD test disc
at inner track
(around #30000)

Notes:
• Use disc: GGV1025

START
Traverse Mechanism
Assy-S
Adjust the radial adjustment
screw so that
ERROR RATE becomes
around "5E-4".
A

• Play the DVD test disc
at inner track
• Display ERROR RATE
on the monitor

ESC CHP/TIM

Traverse Mechanism
Assy-S
Fasten the radial
adjustment screw so that
ERROR RATE becomes
around "1E-3".
B

ERROR RATE : "5E-4"

B

ERROR RATE : "1E-3"

1E-3
BER
5E-4

C

• Unfasten the radial adjustment screw
by 90 degrees step till ERROR RATE
C
becomes around "1E-3" again .
• Record the number of rotation (N1).

B
A

A
Best point

(memorizing how much the screw was rotated.)

• Fasten the radial adjustment screw
till the number of rotation becomes
harf of N1.
Best Radial point

Anticlock wise
Clock wise
Rotation of Radial screw
and Tangential screw

C

ESC

ERROR RATE: - - - -

Player

Service mode end

• Play the DVD test disc
at outer track
(around #200000)

Monitor

D

Turn the POWER OFF in
case of NG once, and
perform the adjustment
once again.

G

E

ESC CHP/TIM

N

If error rate is OK,
locks a root of
tangential and radial
adjustment screws with
the Screw tight.
Screw tight: GYL1001

\ Service mode

Traverse Mechanism
Assy-S
Fasten the tangential
adjustment screw so that
ERROR RATE becomes
around "1E-3".
B

CHECK
OK

In this check, the error rate
that is less than "5E-5"is
better.

ERROR RATE : "1E-3"

Disc playback normally.
• The measurement of
block error rate

ESC CHP/TIM

• Unfasten the tangential screw
by 90 degrees step till ERROR RATE
becomes around "1E-3" again .
C
• Record the number of rotation (N1).

ESC

F

• Fasten the tangential adjustment screw
till the number of rotation becomes
harf of N1.
Best tangential point

Service mode end

64

XV-GX3
1

2

3

4

5

6

7

8

7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 TEST MODE

A

Test Mode Functional Specification
1 Test mode entry
In the power ON state, press the [ESC] (A8-5F) key and [TEST] (A8-5E) key in order of the Test mode remote control unit.
• OSD displays test mode.

2 LD ON
Enter the test mode.
DVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650n).
CD : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n).

B

3 Release the Test mode
• Turn off the power.
• Press the [ESC] (A8-5F) key of the remote control unit and reset it.

C

D

E

F

65

XV-GX3
5

6

7

8

1

2

3

4

7.1.2 DISPLAY SPECIFICATION OF THE TEST MODE

A

2

Character in bold : Item name
: Information display

3
7
8
9

1
5
6
12

13
14
15

B

C

10
11

1 Address indication
The address being traced is displayed in number.
(as for the DVD, indication of decimal number is possible.)
DVD : ID indication (hexadecimal number, 8 digits)
[∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗]
CD : ID indication
[∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗]
2 Code indication of remote control unit [R – ∗ ∗ ∗ ∗]
In case of double code, display a 2nd code.

~ Region setting of the player [REG: ∗]
Setting value : [1] to [6]

5 Tracking status [TRKG – ∗ ∗ ∗]
Tracking on : [ON]
Tracking off : [OFF]

! Destination setting of the FL controller
[MDL: ∗ ∗ ∗ ∗ / ∗ ∗ ∗]
Four characters in the front represent code 01.
Three characters in the back represent the destination code.
J: /J, K: /KU, /KC, /KU/KC, R: /RL/RD, RAM : /RAM,
LB: /LB, WY: /WY

6 Spindle status [SPDL – ∗ ∗ ∗]
CLV : [CLV]
Off : [OFF]
7 Mechanism (loading) position value [M – ∗ ∗]
Unknown
: [01] or [41]
Open state
: [04]
Close state
: [08]
During opening : [12]
During closing : [22]

E

F

- Jitter value [J – ∗ ∗ ∗ ∗]
Note: Don't use it.
= Version of the FL controller [FL: ∗ ∗ ∗ ∗]
Note: Don't use it.

3 Main unit keycode indication [K – ∗ ∗]

D

0 Disc sensing [DSC – ∗ ∗ ∗]
The type of discs loaded is displayed.
[DVD], [CD ]

@ Version of the flash ROM [V: ∗ ∗. ∗ ∗]
Flash ROM size [FLASH = ∗ ∗]

8 Slider position [S – ∗ ∗ ∗ ∗]
In Side Switch ON : [01]
In Side Switch OFF : [00]
9 Output video system [V – ∗ ∗ ∗ ∗]
NTSC system
: [NTSC]
PAL system
: [PAL]
Automatic setting : [AUTO]
Scart terminal output [SK – ∗ ∗]
(Display only the WY model which can do the output setting
of scart terminal.)
VIDEO : [00]
S-VIDEO : [01]
RGB
: [02]

66

XV-GX3
1

2

3

4

5

6

7

8

7.1.3 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY
Only during normal playback, the following shortcut keys can be assigned by pressing a required key after pressing the ESC
key of the remote control unit. To quit, press the ESC key
Command Contents

Conditions

Memory clear and region / revision indication
Average value measurement of DVD error rate
CD error rate measurement
Scart terminal output : VIDEO
Scart terminal output : S-VIDEO

WY, models equipped with Scart terminal

Scart terminal output : RGB
Progressive OFF

Only for progressive models

Progressive ON

A

Remote Control
Remote
Key Name
Control Code

FL indication of ID number
ZOOM ON (×4)
Service mode indication (error rate indication, etc.)

CLEAR (∗1)

A8-45

5 (∗1)

A8-05

5 (∗1)

A8-05

AUDIO

A3-BE

SUBTITLE

A3-36

ANGLE

A3-B5

R_SKIP

A3-9D

F_SKIP

A3-9C

STEREO (∗1)

A8-4A

ZOOM

A3-37

CHP/TIM (∗1)

A8-13

CHAP (∗1)

A8-40

Title search Input mode IN
Title No. input
Search execution

SIDE A (∗1)
Numbers (∗1)
PLAY (∗1)

A8-4D
A8-00 to A8-09
A8-17

Region confimation mode

A.MON (∗1)
Numbers (∗1)

A8-1E
A8-01 to A8-08

Model information indication

B

∗1 : Test mode remote control unit
C

• Service mode indication (ESC + CHP/TIM keys)
ID Address
The error rate is always displayed in exponential notation, e.g., ∗.∗ ∗ e - ∗, for both DVDs and CDs.
EDC/ID/AV 1 error history (ID Address, EDC/ID Error, last eight errors)

• Calculation of the average error rate (ESC + "5" [Test mode remote control unit] keys)
The average of the last eight error rates is calculated and indicated in exponential notation. After the calculation is completed, "OK" or "NG" is
displayed. If "NG" is displayed, the disc tray will open (for both DVDs and CDs)
For DVDs: OK with 5.0e-4 or less, for CDs: OK with 7.6e-3 or less

• Indication of model information (ESC + CHAP keys)
The items from 12 to 15 of the TEST MODE Indications are displayed. However, in the indications, S in the standard test mode is changed to
CHIP VERSION, and M is changed to RF VERSION. For details, see 7.1.4.

D

• Region confirmation mode (ESC + A.MON [Test mode remote control unit] + "1"-"8" [Test mode remote control unit] keys)
After you press the AUDIO key while holding the ESC key pressed and then input the region number, if the number is different from that set in
the unit, an error message is displayed, and the tray opens.

E

F

67

XV-GX3
5

6

7

8

1

2

3

4

7.1.4 SPECIFICATION OF THE MODEL INFORMATION DISPLAY

A

To display model information : Press the ESC key then the CHAP key.
To close the model information display : Press the ESC key.

• Display contents

1
10
9
B

2

Don't care.
3
4
5
6
7

Character in bold : Item name
: Information display
C

1 Destination indication
Display it according to model information set from the FL controller.
2 Region No.
3 Part number
4 ROM version
5 Flash size

D

6 FL controller version
7 CHIP VERSION
9 Remote control code
0 Key code of Main unit

E

F

68

XV-GX3
1

2

3

4

5

6

7

8

7.1.5 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE
• Display during Service Mode
To enter Service Mode, press the CHP/TIM key while holding the ESC key pressed.
To quit, press the ESC key.

A

Service mode display
1 ID Address
2 Error rate (always displayed), in exponential notation
ERROR RATE : ∗ ∗ ∗ ∗ ∗ ∗ ∗
(∗∗∗∗)
Number of error
• Calculation of the average error rate
For DVDs: OK with 5.0e-4 or less, for CDs: OK with 7.6e-3 or less

B

ex) For DVDs
• Step 2

• Step 1

%%e -&
%%e -6
%%e -5
%%e -4
%%e -3
%%e -2

%%e -4
: OK
: OK
: Refer to Step 2
: NG
: NG

3.0e -4
4.0e -4
5.0e -4
6.0e -4
7.0e -4

: OK
: OK
: OK
: NG
: NG
C

3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors)
Note:
∗ Error of AV1 is not supported in this player.

Indication plan contents
3
1
2

D

Character in bold : Item name
: Information display
E

F

69

XV-GX3
5

6

7

8

1

2

3

4

7.1.6 SERVICE TEST MODE
1. Conditions During Service Test Mode
A

• During Service Test mode, the unit will not be shut down for an emergency even if one of the failures mentioned below
occurs.
• After the unit has been shut down in Normal mode for an emergency upon detection of one of the failures mentioned below,
you can turn it on immediately, without waiting for one minute, in Service Test mode.
• The accumulated power-on time can be checked during Service Test mode.

2. How to enter Service Test mode
• Connect AC power cord with the STEST port (microcomputer terminal IC5501: 43-pin) at High (5 V). (See "Service Test
mode connecting point".)
Note: Initial function setting is DVD/CD.
• Connect AC power cord while holding both the  and POWER keys on the main unit pressed. The unit will be turned on,
and the following indication will be displayed:
B

3. How to quit Service Test mode, and conditions for quitting
• To quit Service Test mode, turn the power off or disconnect the AC power cord to turn the power off.
• When Service Test mode is quit, only data on protection in RAM will be initialized, and data on user settings in RAM will not
be initialized.

4. Indications on the FL display when Service Test mode is entered
• Indications on the FL display when Service Test mode is entered differ depending on whether the unit was turned off
normally or shut down for emergency protection, immediately before Service Test mode starts, as follows:
[After a normal power-off]
FL display

C

FL display
FL display

We l c om e
V o l
D V

0

S R V C E
[After a shutdown caused by an AMP-system failure]

[After a shutdown caused by an AMP-system abnormality]
FL display

P R T C T

FL display

V o l

FL display

D V

WG

FL display

P R T C T

0

FL display

V o l

S R V C E

FL display

D V

E R
0

S R V C E

D

[After a shutdown caused by a DVD-system failure]
FL display
FL display
FL display

E

D V

FL display

P R T C T

V o l
D V

[After a shutdown caused by an EEPROM (IC5401) failure]

FL display

0

FL display

S R V C E

E E P

E R R

V o l
D V

0

S R V C E

5. Operations during Service Test Mode
• Basically, operations in Service Test mode are the same as in Normal mode. However, to indicate that the unit is in
Service Test mode, the following are displayed when the functions are changed:
[Functions]

[FL display]

DVD/CD

D V

S R V C E

TUNER

T X

S R V C E

TAPE

T C

S R V C E

LINE

L N

S R V C E

F

70

XV-GX3
1

2

3

4

5

6

7

8

6. Failures
• Depending on the types of errors, one of the following error messages will be displayed when the unit is turned on:
P R T C T

A

WG

A protection circuit was activated:
1. The V+10, V+5, V+3R3, or VFDP was short-circuited (See the protection circuit on "3.4 DVD MAIN ASSY (2/2)"),
or the value at V+10, V+5, or V+3R3 exceeded the standard value because of an abnormality in its power section.
2. The XPROTECT line up to the system-control computer (PDC129A) was short-circuited by grounding or was broken.
P R T C T

E R

A protection circuit was activated:
1. The V+10, V+5, V+3R3, or VFDP was short-circuited (See the protection circuit on "3.4 DVD MAIN ASSY (2/2)"),
or the value at V+10, V+5, or V+3R3 exceeded the standard value because of an abnormality in its power section.
2. The XPROTECT line up to the system-control computer (PDC129A) was short-circuited by grounding or was broken.
D V

B

P R T C T

Abnormality in the DVD section
1. The V+6R8, V+5V, or V+3 was short-circuited, or the value at V+6R8, V+5V, or V+3 exceeded the standard value
because of an abnormality in its power section.
2. The VDET line up to the system-control computer (PDC129A) was short-circuited by grounding or was broken.
(See VDET circuit on "3.4 DVD MAIN ASSY (2/4)")
E E P

E R R

1. Breakage or short-circuiting of the communication line between the µ-COM (IC5501) and the EEPROM (IC5401) can
be suspected.
2. A failure in the EEPROM (IC5401) can be suspected.
C

7. Accumulated power-on time display
• Hold the STOP key on the unit pressed for 8 seconds during Service Test mode. After the version for the system-control
computer is displayed, the accumulated power-on time is displayed.
Version of the system-controller

P D C 1 2 9 A
About 3 seconds after

Accumulated power-on time

1 0 H 3 0 M

• Power-on time is always counted while the power is on, regardless of unit's functions and operations.
However, it is not counted during Standby mode.
• The maximum countable power-on time is 255H59M (255 hours 59 minutes.) The indication will not advance beyond that.
• The accumulated power-on time basically cannot be cleared.

D

Service Test Mode connecting point
Connecting point

R5537

R5538

R5539
R5540
R5541
R5542

31

R5514

R5512

R5522

STEST

R5531
C5505
R5544
C5401
R5546
R5545
R5402
C5402

IC5401

VE+5

R5401

UTEST
R5525
R5526
R5527
R5528
R5529
R5530
R5535
R2906

R5513
R5532

R5516
R5515
C5510
C5509

MUTE

C5506

C5501

50

R5511

R5510
C5587
C5504
R5521

TCMODE

5

R5519

4

ADY

30

K

E

R5550

51

1

A

C5507

R5565

01
55
IC

10
0

R5502

ST

R5543 R5547
R5548 R5549

R5564

80

81

R5552
R5551

C5

SIDE B

8

MAIN ASSY

1

C

GNDU

F

Q2902
Q2906

Q2905

71

XV-GX3
5

6

7

8

1

2

3

4

7.1.7 METHOD FOR DIAGNOSING DEGRADATION OF THE LDs ON THE PICKUP ASSY

A

Case when this diagnosis is required :
When playback of any disc, including a test disc (DVD: GGV1025, CD: STD-905), won't play or doesn't play

How to diagnose
In the case mentioned above, degradation of the laser diodes (LDs) mounted on the 05SD Pickup Assy is suspected.
Measure the voltage between the two ends of one of the resistors mentioned below.

No playback of a DVD :
Measure the voltage between the both ends of R322 or R325 on the DVDM
Assy. If the voltage is 0.4 V or higher, the 650-nm LD is degraded.

B

No playback of a CD :
Measure the voltage between the both ends of R321 or R326 on the DVDM
Assy. If the voltage is 0.4 V or higher, the 780-nm LD is degraded.

If the measurements show degradation
of an LD, replace the 05SD Pickup
Assy.

05SD PICKUP ASSY
C

CN101

B

DVDM ASSY

D

R325
R326

E
R322

R325
R326

R321

Front side

SIDE A

F

72

XV-GX3
1

2

3

4

5

6

7

8

7.1.8 DVD TROUBLE SHOOTING
No.
1

Symptoms

Diagnosis Contents

Possible Defective Points

The power is not turned on. Are wires of output connector (POWER SUPPLY Unit) and CN901
(DVDM Assy) disconnected or damaged ?
Check that the following voltage is output :
+ side of C739 : 3.3V

2

A

Connector / cable
DVDM Assy
3.3V Regulator IC (IC341)

An opening screen is not
Are the signals output from IC201-pin 98 (MDATA) and pin 99 (SCLK)
displayed on the monitor
on the DVDM Assy ? (in the range of 0-3V)
(The FL display lights. The
mechanism does not work.)
Are the signals input into IC5501-pin 50 (MDATA) and pin 51 (SCLK)
on the IFAF Assy ? (in the range of 0-3V)

DVDM Assy
DVD IC (IC201)
MAIN Assy
UCOM (IC5501)

Check that the following voltage are output :
IC751-pin 1 on the DVDM Assy : 5V

DVDM Assy
5V Regulator IC (IC751)

Is a resonator (X201: 27MHz) on the DVDM Assy oscillating ?

DVDM Assy
Crystal resonator (X201)
DVD IC (IC201)

• Is a signal input into IC203-pin26 (PCE#) on the DVDM Assy ?
(Is a signal "H" for 80 mS and then "L" after the power is turned
on ?)
→ Communication with flash ROM.
• Are the signals input into IC202-pin 16 (DWE#), pin 19 (DCS#)
and pin 38 (SDCLK) on the DVDM Assy ?
(Is a signal fluctuating ?)
→ Communication with SDRAM

DVDM Assy
DVD IC (IC201)
Flash ROM (IC203)
SDRAM (IC202)

B

C

Is a signal output from IC203-pin 28 (PRD#) on the DVDM Assy?
DVDM Assy
(Is a signal fluctuating for several hundred mS after the power is turned Flash ROM (IC203)
on ?)
Is a signal input into IC5501-pin 67 (DVD ACK) on the CONTROL
Assy ? (Is a signal fluctuating ?)
→ Communication with FL Control IC

DVDM Assy
DVD IC (IC201)
MAIN Assy
UCOM (IC5501)

Is a signal output from IC5501-pin 30 (XREADY) on the CONTROL
Assy ? (Is a signal fluctuating in the range of 0-5V ?)

MAIN Assy
UCOM (IC5501)

DVDM Assy
Are the signals output from IC5501-pin 49 (SDATA) on the CONTROL DVD IC (IC201)
Assy ? (in the range of 0-5V)
MAIN Assy
UCOM (IC5501)

D

Are the signals of IC204-pin 5(SDA) and pin 6(SCL) on the DVDM Assy DVDM Assy
fluctuating for one or two seconds after the power is turned ?
EEPROM (IC204)
3

An opening screen is not
displayed on the monitor
(The FL display lights. The
mechanism works.)

DVDM Assy
Check the video signal path between DVD IC (DVDM Assy IC201) and
Video circuit after DVD IC
video-out terminal (see the block diagram)
(IC201)

E

F

73

XV-GX3
5

6

7

8

1

No.

2

Symptoms

A

4

A tray cannot be opened.
(An opening screen is
displayed on the monitor)

3

Diagnosis Contents

Possible Defective Points

Does the voltage of CN104-pin 3 and pin 5 on the DVDM Assy change
normally ?
Pin 3 (SW2(TRIN)): Tray is fully closed: "L"
Pin 5 (SW1(TROUT)): Tray is fully opened: "L"
Is the signal input into IC101-pin 11 (TROPEN) on the DVDM Assy ?
At open: 3.3V, At close: 0V
Are the signals output from IC101-pin 1 and pin 2 (CN103-pin 1 and
pin 2) on the DVDM Assy ?
Pin 2: Approx. 6V during opening tray approx. 0V during closing tray.
Pin 1: Approx. 0V during opening tray approx. 6V during closing tray.
Are wires of CN104 and CN103 on the DVDM Assy disconnected or
damaged ?

B

5

Playback impossible
(no focusing)

C

D

E

6

Playback impossible
(Spindle does not turn)

7

Playback impossible
(Playback stops)

8

Picture disturbance during
playback
(block noise, freeze, other)

9

No sound
(Picture is normal)

4

Does the voltage of CN102-pin 1 on the DVDM Assy change to 0V by
pressing the Inside switch.
Are the signals output from IC101-pin 3 (FOCS_DRV) and pin 4
(FOCS_RTN) on the DVDM Assy ?
Does 650-nm LD emit light ?
Does a pickup lens move up / down ?
Does an actuator spring bend ?
Are plastic parts damaged ? Or is a shaft detached ?
Is the turntable detached or tilted ?
Is flexible cable of CN101 on the DVDM Assy disconnected or
damaged ?
Is signal output from IC201-pin 42 (FOSO) on the DVDM Assy ?
(Device control of about 1.4 V is output usually. It is fluctuated by about
± 250 mV with focus up / down.)
Are the signals output from IC101-pin 30 (W), pin 33 (V) and pin 35 (U)
on the DVDM Assy ?
Is pin 26 (STBY) fixed LOW ? (pin 26 is High at playback: 3V)
Is there any part detached from the spindle motor ?
Or Is there any foreign object lodged in it ?
Are wires of CN102 on the DVDM Assy disconnected or damaged ?

LOAB Assy
Tray SW (S101)
DVDM Assy
DVD IC (IC201)
DVDM Assy
FTS Driver IC (IC101)

Connector / cable
Inside switch
DVDM Assy
FTS Driver IC (IC101)
Pickup
Mechanism section (motor)
Flexible cable / connector
DVDM Assy
DVD IC (IC201)
DVDM Assy
FTS Driver IC (IC101)

Mechanism section
(Spindle motor)
Flexible cable / connector
DVDM Assy
Is signal output from IC201-pin 37 (DMSO) on the DVDM Assy ?
DVD IC (IC201)
Does 650-nm LD deteriorate ?
650-nm LD deteriorated.
If the voltage at each both ends of R322 and R325 on the DVDM Assy (When playback of a DVD is
is 0.4 V or more, the 650-nm LD is definitely deteriorated.
impossible)
Does 780-nm LD deteriorate ?
780-nm LD deteriorated.
If the voltage at each both ends of R321 and R326 on the DVDM Assy (When playback of a CD is
is 0.4 V or more, the 780-nm LD is definitely deteriorated.
impossible)
DVDM Assy
Is there abnormality in FG waveform ? (IC201-pin 47)
FG output : FTS Driver IC (IC101)
Are there scratches or dirt on the disc ?

Disc

Are there scratches or dirt on the disc ?
Is there a problem with the format of the disc ?

Disc

Check the video signals.
Composite video signal (IC401-pin 25)
S video signal (IC401-pin 21, pin 26)
RGB video signal (IC401-pin 16, pin 18, pin 20)

DVDM Assy
DVD IC (IC201)
Video IC (IC401, IC451)

Check the waveform (SPDIF: CN901-pin 16).

DVDM Assy
DVD IC (IC201)

F

74

XV-GX3
1

2

3

4

5

6

7

8

Symptoms that may occur when any of the following ICs is in failure
IC

A

Symptoms

EEP ROM
(DVDM Assy : IC204)

User's data cannot be stored in memory.
The ID number is lost.

Flash ROM
(DVDM Assy : IC203)

The power cannot be turned on.
Downloading of the firmware cannot be performed.

DVD IC
(DVDM Assy : IC201)

Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be
generated, because the DVD processing is performed by a single chip.

64M SDRAM
(DVDM Assy : IC202)

No power.
Block noise is generated during playback.
B

C

D

E

F

75

XV-GX3
5

6

7

8

1

2

3

4

7.1.9 ID NUMBER AND ID DATA SETTING

A

Caution:
For the DVD players compatible with DVD-RW, for playback of a DVD-RW disc (CPRM), it is necessary that an individual ID
number and ID data are set for each player. If the ID number and ID data be not properly set in the manner described below,
future operations cannot be guaranteed. The ID number is written on the yellow label at the rear panel of the player.
If there is no yellow label, before downloading FLASH ROM, take note of the ID number set following the procedures
outlined in "ID Number Confirmation Mode" on the next page.
Note: Enter ID numbers while the unit is in Stop mode so that the values set will be immediately written to the flash ROM.
Setting an ID number or ID data is required in the
following case:
If NO NUM! or NO DATA is displayed on the FL display
immediately after the power to the player is turned on or
during Stop mode.

5 After entering all 9 digits, if you press the SEARCH key, the
unit unconditionally sets the input number as the ID number.
Then the unit automatically enters Player's Data Input Mode.
(The SEARCH key is not accepted after all 9 digits have been
entered.)

B

[Player's ID Number Setting]
ID Number ?
000000001

JIGS AND MEASURING INSTRUMENTS


Compare Mode
 Enter

4
5

Input ID Number !
Service Remote Control Unit
[GGF1381]

DVD Data Disc
[GGV1175]

C

6 This display appears when the PLAY key is pressed in Step 4.
Enter a 9-digit number to compare. The number is also
displayed on the FL display.

ID Number Input Mode
1 To enter ID Number Input Mode, with no ID number set, such as
in a case of immediately after upgrading the firmware, press the
ESC key then the STEREO key.

7 By pressing the CLEAR key without having input a number, the
unit returns to Step 2 without doing anything else. Each press
of this key after a number has been input deletes one digit.

Note: If a previous ID number and ID data, such as a factorypreset ID number and ID data, are maintained, the unit
enters ID Number Confirmation Mode when the above keys
are pressed. However, if only an ID number is maintained,
the unit enters ID Data Input Mode.
D

2 Enter a 9-digit ID number. The ID number is also displayed on
the FL display.

[Player's ID Number Setting]
ID Number ?
000000001
Compare
∗∗∗∗∗∗∗∗∗

6

3 By pressing the CLEAR key without having input a number, you
can exit this mode. Each press of this key after a number has
been input deletes one digit.

2

[Player's ID Number Setting]
ID Number ?
---------

8 After entering all 9 digits, if you press the PLAY key, the unit
compares the numbers input in Steps 2 and 6, and only if the
numbers match, that number is set as the ID. Then the unit
automatically enters ID DATA Input Mode. If the numbers do not
match, the disc tray is opened, and the unit exits ID Number
Input Mode.

 Exit

3

Input ID Number !

E

Note: If you press the PLAY button before inputting a 9-digit ID
number, the unit returns to Step 6 without doing anything
else.

Input ID Number !

[Player's ID Number Setting]
ID Number ?
000000001
Compare
000000001

4 After entering all 9 digits, if you press the PLAY key, the unit
enters Compare mode. Enter the same ID number again. Only
if your two input numbers match, the ID number is set. Compare
mode helps eliminate mistyping of the ID number.

F

Note: If you press the PLAY button before inputting a 9-digit ID
number, the unit returns to Step 2 without doing anything
else.

 Enter

8

Input ID Number !

76

XV-GX3
1

2

3

4

5

6

7

8

ID Number Confirmation Mode
1 To enter ID Number Confirmation Mode after the ID number and
the ID data are set, press the ESC key then the STEREO key.
2 The ID number already set is displayed.
(It is also displayed on the FL display.)
3 Enter a 9-digit number for comparison. This is not required
when you only wish to check the ID number visually.
(The number is also displayed on the FL display.)
4 By pressing the CLEAR key without having input a number, you
can exit this mode. Each press of this key after a number has
been input deletes one digit.

2
3
4

A

• Indication of an ID number already set
An ID number already set is displayed in the following cases:
1) When the ESC key then the CLEAR key are pressed, user
settings are cleared, then the ID number set is displayed on
the screen. In this case, the ID number is not displayed on the
FL display.
2) When the unit enters ID Number Confirmation Mode by your
pressing the ESC key then the CLEAR key, the ID number set
is displayed. In this case, the ID number is also displayed on
the FL display.
If you only need to confirm the ID number, you can exit
this mode by pressing the CLEAR key or turning off the power.

• Indication when no ID number is set

[Player's ID Number Setting]
ID Number ?
000000001
Compare
∗∗∗∗∗∗∗∗∗

B

If no ID number is set, the message "NO NUM!" flashes on
the screen and FL display for a few seconds after the power is
turned on or during Stop mode.

 Exit
Input ID Number !

C

5 After entering all 9 digits, if you press the PLAY key, the unit
compares the number entered in Step 2 with the ID number
set, and only if the numbers match, the unit automatically exits
ID Number Confirmation Mode. If an ID data has not been
entered, the unit enters ID DATA Input Mode. If the numbers do
not match, the disc tray is opened, and the unit exits ID Number
Confirmation Mode.
Note: If you press the PLAY button before inputting a 9-digit ID
number, the unit returns to Step 4 without doing anything
else.
6 After entering all 9 digits, if you press the STOP key, the unit
compares the number entered in Step 3 with the ID number
set, and only if the numbers match, the unit automatically
deletes the ID number and exits this mode. If the numbers do
not match, the disc tray is opened, and the unit exits this mode.
(The STOP key is not accepted after all 9 digits have been
entered.)

D

[Player's ID Number Setting]
ID Number ?
000000001
Compare
000000001
5
6

E

 Enter
 Memory Clear
Input ID Number !

F

77

XV-GX3
5

6

7

8

1

2

3

4

ID DATA Input Mode
A

1 To enter ID DATA Input Mode, with the ID number set, press the
ESC key then the STEREO key.
2 When the STEREO key is pressed, the unit enters ID DATA
Input Mode.

Note: Whether or not the data have been written to flash ROM can
be confirmed by watching for the message "Rom Write OK!"
being displayed after the disc is read.

[Player's Data Input Mode]

[Player's ID Number Setting]
ID Number ?
[000000001]
Compare
>∗∗∗∗∗∗∗∗∗

B

5 When writing of the data read from the disc to flash ROM is
completed, "Rom Write OK!" is displayed. After seeing this
message, you can exit this mode by pressing the CLEAR key.

Rom Write OK!

5

 Exit

 Exit
 ID Data Setting Mode

2

Input ID Number !

C

3 If the DVD DATA DISC is loaded in this mode, the unit
automatically starts reading the data.
(If the DVD DATA DISC has already been loaded, the unit does
not start reading the data. In this case, open then close the
tray.)

6 If the data cannot be read from the disc, "Disc Error!" is
displayed on the screen, and the disc is ejected.

[Player's Data Input Mode]

4 To exit this mode, press the CLEAR key. While data are being
read from the DVD DATA DISC, you cannot exit this mode.

[Player's Data Input Mode]

Disc Error!

6

 Exit

D

 Exit

4

• Indication when the data have not been set

Insert The ID Data Disc !

If no ID data are set after the ID number is changed, the message
"NO DATA" displays on FL display after the power is turned on or
during Stop mode.

E

F

78

XV-GX3
1

2

3

4

5

6

7

8

7.1.10 DISASSEMBLY
Note 1: Do NOT look directly into the pickup lens. The laser beam may cause eye injury.
Note 2: Even if the unit shown in the photos and illustrations in this manual may differ from your product, the procedures
described here are common.
Note 3: For performing the diagnosis shown below, the following jigs for service is required:
• Flexible cable for service (GGD1309, GGD1447)

A

Diagnosis of PCB's
1 Bonnet and Tray panel

1

Remove 11 screws from Bonnet.

6

Press the 0 OPEN/CLOSE button to close the Tray.
(Test disc is clamped.)
Press the  STANDBY/ON button to turn off the power.

1

7
8

B

Pull out the Power cord.

How to open the Tray when the power cannot be on
Insert a Tweezer(as shown in the photo) into the Slit located at
the bottom of the unit and slide the projection of the Drive Cam in
the Loader Assy in the direction of the arrow, as indicated in the
photo.
If the Tray pops out a little, fully pull it out by hand.
C

Tweezer

1
Rear View

2
3
4
5

Press the  STANDBY/ON button to turn on the power.
Press the 0 OPEN/CLOSE button to open the Tray.
Remove the Tray Panel.
D

Set the Test Disc.
Slit

2 7

Bottom View

3 6
4
Tray Panel
E

5
3

Test Disc

6

F

79

XV-GX3
5

6

7

8

1

2

3

4

2 Front Panel and Rear Panel
A

1
2

6

Remove the grounding screw of the MIC Assy.

Remove 2 screws from Bottom Chassis and Rear Panel.

Disconnect FFC Cables at CN5651, CN3991 and CN3051.

E

B

MIC Assy

2
6

Bottom View

C

1

MAIN Assy

5

7

Disconnect the FFC Cables at CN1501 and CN3001.
(Do not remove other cables.)

8

Remove 2 screws on the MAIN Assy.

7

MAIN Assy

3
4
5

Remove the grounding screw.
Disconnect the cables at CN2302, CN2301 and CN2901.
Released the hook at the right and left side of the Front
Panel Assy.

C

D

MAIN Assy

4
8
9

Slide the Heatsink Holder to the Rear Panel side, and take
out the Rear Panel and MAIN Assy.

E

5
3
Heat Sink

Heatsink Holder

Rear Panel

F

80

XV-GX3
1

2

3

4

5

6

7

8

3 MAIN Assy diagnosis

1

3

Set the Rear Panel and MAIN Assy upright.

C

A

Take the original cable off from CN901 of the DVDM Assy to
use the GGD1309 cable to connect to CN1501 of the MAIN
Assy.
In the same way, take the original cable off from CN902 of
the DVDM Assy to use the GGD1447 cable to connect to
CN3001 of the MAIN Assy.

MAIN Assy

B

GGD1309

C

2

Set the Front Panel upright, which you took off in the previous procedure, and connect the six cables to CN5651,
CN3991, CN3051, CN2901, CN2302, and CN2301 of the
MAIN Assy, respectively.

GGD1447

B

DVDM Assy

Front Panel

D

2

E

F

81

XV-GX3
5

6

7

8

1

A

2

3

4

4 DVD Main Board diagnosis

1

Remove 4 screws on the DVDM Assy.

B

1

B

2

DVDM Assy

Set the DVDM Assy upright.

C

C

D

MAIN Assy

DISPLAY Assy

D

E

B

MIC Assy

DVDM Assy

E

F

82

XV-GX3
1

2

3

4

5

6

7

8

Removing the Traverse Mechanism Assy-S and 05SD Pickup Assy-S
A

Rear view

1 05 LOADER Assy

1

05SD Pickup Assy-S

Short-circuit point by soldering.

Note: After replacement, connect the flexible cable,
then remove the soldered joint (open).

2
3
4

Disconnect the four connectors.
Remove the two screws.
B

Remove the 05 LOADER Assy.

1
3

05 LOADER Assy
C

4

D

2
2
2

E

2

F

83

XV-GX3
5

6

7

8

1

2

3

4

2 Bridge 04, Tray
A

1
2
3

Remove the one screw.
Remove the bridge 04.

3

Pull out the tray, then remove it by pressing the
hook.

-2

Hook

Bridge 04

B

1
2

C

3

-2

Tray

D

E

Note when reinserting the tray
When reinserting the tray, first align the triangle
printed on the loading base and the pin of the drive
cam, then insert the tray.

Drive cam

Pin

Front side
F

Loading base

84

Triangle

XV-GX3
1

2

3

4

5

6

7

8

3 Traverse Mechanism Assy-S

1

A

Flexible cable
for the spindle motor

Dislodge the two flexible cables from their factory
placement.

Front Side

1

B

1

C

Flexible cable for the pickup
Bottom view

2
3

D

Unhook the four hooks.

Traverse Mechanism Assy-S

Remove the Traverse Mechanism Assy-S

2

×2

3

E

2

×2

F

85

XV-GX3
5

6

7

8

1

2

3

4

4 05SD Pickup Assy-S
A

Note: The 05SD Pickup Assy can be removed
without removing the TTraverse Mechanism
Assy-S.(shown as Step π.)
05SD Pickup Assy-S

1

Front Side

Disconnect the flexible cable for the pickup.

B

1

C

Flexible cable for the pickup
Bottom view

D

2
3

Remove the two adjustment screws.
Adjustment screw
(skew screw VK1)

Remove the 05SD Pickup Assy.

2

2

Adjustment screw
(skew screw VK1)

05SD Pickup Assy-S

3
E

Note: Be careful not to lose the adjustment spring
(skew spring VK1).
Adjustment screw
(skew screw VK1)
Adjustment spring
(skew spring VK1)

F

86

XV-GX3
1

2

3

4

5

4

6

7

8

Remove the one screw.

05SD Pickup Assy
A

Note: The screw is secured with the silicone
adhesive.
Make sure to apply the silicone adhesive after
reattaching the screw.

Joint VK1B

Joint spring VK1

B

4
Silicone Adhesive
GEM1037

C

Arrangement of the flexible cable for the spindle motor
: Conductive surface

Hook

Front Side

D

E

Hook

F

Bottom view

87

XV-GX3
5

6

7

8

1

2

3

4

Arrangement of the flexible cable for the pickup
A

: Conductive surface
Note:
Be sure to move the 05SD Pickup Assy to the innermost perimeter.

1

Fold the flexible cable for the pickup with the backing outward
in the illustration below.

4
5

Hook the part folded in Step 1 to the hook.
Pass the flexible cable through the hook.

Reference line
Reference line
Hook

1

B

5

4

Backing
76 mm

Hook

C

2

6
7

Attach the flexible cable for the pickup to the connector.

Fold the flexible cable along the hook.
Pass the flexible cable through the hook.

Hook

2
7
Backing

6

D

Front Side

Bottom View
Hook

3

Pass the flexible cable through the hook.

E

Hook

Hook

3

Make sure that the cable is loose
F

88

XV-GX3
1

2

3

4

5

6

7

8

7.2 PARTS
7.2.1 IC
• The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams.

• List of IC

A

PDC129A

PDC129A (MAIN ASSY : IC5501)
• System Control Microcomputer

 Pin Functions
Pin Name

No.

I/O

Pin Function
Control power supply for DVD module

1

DVDON/OFF

O

2

NC

O

3

MICDET

I

Mic Detection

4

ACPULSE

I

AC PULSE input detection (Interruption 0)

5

NC

O

6

(RDSCLK)

O

7

REMOCON

I

REMOCON signal input (Interruption 3)

8

XRESET

I

µ-com reset input

B

9

XT1

−

Subclock (connect to VDD when no use)

10

XT2

−

Subclock (leave open when no use, and set the bit 6 of OCR SFR)

11

VSS1

−

12

CF1

−

Main Clock (connect to VDD when no use)

13

CF2

−

Main Clock (leave open when no use)

14

VDD1

−

15

SIMUKE

I

Destination distinction input

16

MODEL

I

Model distinction input

17

VDET

I

DVD3.3V detection input

18

KEY1

I

Key1 input

19

KEY2

I

Key2 input

20

JOG

I

JOG

21

LEVELIN

I

Level meter signal input

22

XPROTECT

I

23

SDATA

O

System bus data output (for DVD)

24

MDATA

I

System bus data input (for DVD)

25

SCLK

I

System bus clock input(for DVD)

26

FLCE

O

CE for FL driver

27

FLDATA

O

Data for FL driver

28

FLCLK

O

Clock for FL driver

29

NC

O

30

XREADY

O

31

NC

O

32

XRECMUTE

O

REC OUT MUTE

33

UTEST_CHK

O

UNITCHECK IN for checker

34

UTEST_EEPOK

O

EEPROM CHECK OK for checker

35

RELAY

O

SP RELAY ON/OFF

36

NC

O

37

NC

O

38

NC

O

39

VSS4

−

40

VDD4

−

C

D

Chip select for system bus (to DVD module)

E

F

89

XV-GX3
5

6

7

8

1

No.

A

B

C

D

E

Pin Name

2

3

I/O

4

Pin Function

41

NC

O

42

NC

O

43

STEST

I

44

UTEST

I

Set UNITCHECK for checker

45

ECHCONT1

O

Control for ECHO1

46

ECHCONT2

O

Control for ECHO2

47

NC

O

48

EPROM_CS

O

EEPROM CS

49

EPROM_O

O

EEPROM D0

50

EPROM_I

I

EEPROM D1

51

EPROM_CLK

I

EEPROM CLK

52

TXCE

O

Chip enable for Tuner LSI

53

NC

−

54

NC

−

55

VDD2

−

56

VSS2

−

57

TCHALF

I

Input switch of mecha half

58

TCMODE

I

Input switch of mecha mode

59

TCRECF

I

Input switch of mecha during recording forward

60

TCRECR

I

Input switch of mecha during recording reverse

61

TXCLK

O

Clock for tuner LSI

62

TXODATA

O

Data for tuner LSI

63

NC

O

64

(RDSPOW)

O

Control power supply of RDS(L:POWER ON)

65

(RDSDATA)

I

Input RDS data

66

TXIDATA

I

Input data from tuner LSI

67

DVDACK

I

Ackknowlegement from DVD MODULE(Interruption 4)

68

TCPULSE

I

Input pulse of TC reel

69

NC

O

70

TCMSIN

I

71

NC

O

72

NC

O

73

LED1

O

74

NC

O

75

NC

O

76

NC

O

77

NC

O

78

NC

O

79

NC

O

80

NC

O

Set TESTMODE for Service

Input MS signa

LED1

F

90

XV-GX3
1

2

3

4

5

No.

Pin Name

6

7

I/O

8

Pin Function

81

PB/XRCE

O

82

NC

O

83

MOTOR

O

Output tape motor

84

SOL

O

Output tape solenoid

85

BEATCUT

O

Control beat cut of deck

86

BIAS

O

Control bias of deck

87

NC

O

88

VSS3

−

89

VDD3

−

90

FLASHE/D

−

for FLASH writing / On board debugger

91

FLASHDO

−

for FLASH writing / On board debugger

92

FLASHCLK

−

for FLASH writing / On board debugger

93

XDVDRST

O

RESET to DVD MODULE

94

SYSMUTE

O

Control mute of system

95

SYSPOW

O

Control power supply of system

96

VOLCLK

O

Clock for E-vol IC

97

VOLDATA/CE

O

98

NC

O

99

NC

O

100 NC

O

A

Switch PB/REC

B

C

D

E

F

91

XV-GX3
5

6

7

8

1

2

3

4

8. PANEL FACILITIES
Front panel
A

1

2

3

4

5

6

7

8

PUSH OPEN

 STANDBY/ON

REVERSE
MODE

P.BASS

REC/STOP

FUNCTION

B


 OPEN/CLOSE

MIC

MAIN

MIC VOL

SUB

9 10

MIN

MAX

11

12

C

8 PUSH OPEN
Press down on this side of the cassette door to
open the tape deck.

1
STANDBY/ON
Switches the player on or into standby.
2

Remote sensor

9 
 OPEN/CLOSE
Ejects the disc.

3 P.BASS
Press to switch on the bass boost.

10 Headphone jack

4 Display
See Display below.
5
D

11 MIC VOL and MIC input jacks
Controls the volume of the karaoke mics
(MAIN and SUB).

Tape cassette controls
REVERSE MODE – Selects the playback
mode for tapes.
REC/STOP– Starts/stops recording on the
tape deck.

12 Disc tray

6 FUNCTION
Selects the source you want to listen to.
7 Playback / volume control
The playback controls are used for playing,
pausing, skipping and stopping playback. Turn
the middle section to adjust the volume.

E

F

92

XV-GX3
1

2

3

4

5

6

7

8

Display
1

2

3

5

4

6

7
A

KEY ECHO
PRGSVE
RPT-1
kHz PGM
MHz RDM

P.BASS SFC
DTS B.CUT L R
D REC

8 9

1

2

6

10 11

Format indicators
DTS - Lights during playback of a DTS source.
2 D - Lights during playback of a Dolby
Digital source.
Sound processing indicators
P.BASS - Lights when the bass boost is
switched on.
SFC - Lights when one of the Sound Field
Control modes is selected.

- Lights when a stereo FM broadcast is
being received in auto stereo mode.
- Lights when FM mono reception is
selected.
8
Lights when the sleep timer is active.
9

3 
Lights during playback.
4

Character display

Cassette deck indicators
B.CUT - Lights when the beat cut mode has
been switched to B.CUT 2.
REC - Lights when recording to the tape deck.
 - Indicates the direction of tape playback.
- Indicates the reverse mode.

5 PRGSVE
Lights when the player is set to output
progressive scan video.

10 kHz / MHz
Indicates the unit of the frequency shown in the
display (kHz for AM, MHz for FM).

6

11 Playback mode indicators
RPT-1 - RPT lights during repeat play
(RPT-1 lights during repeat one-track/
chapter play).
PGM - Lights during program play.
RDM - Lights during program play.

Karaoke indicators
ECHO - Lights when the Karaoke ECHO
effect is selected.
KEY - Lights when the Karaoke pitch control
is selected.
(Vocal cancel) ñ Vocals in the backing
track are partially eliminated using EQ.
L - Left channel only. Use for tracks that
have a vocal recorded in the right channel.
R - Right channel only. Use for tracks that
have a vocal recorded in the left channel.
L R - Use to put a single-channel vocal track
into the center of the mix.

7

B

C

D

Tuner indicators
- Lights when a broadcast is being received.

E

F

93

XV-GX3
5

6

7

8

1

2

3

4

Remote control
A

P.BASS

STANDBY/ON

9

1
2

DVD/CD

FM/AM

LINE

TUNER

TAPE

PGM

RPT

RDM

1

2

3

4

5

6

AUDIO

SUBTITLE

ANGLE

7

8

9

VOLUME

3
B

SYSTEM SETUP

4
5

3 Number buttons and SHIFT functions
The number buttons can be used for selecting
titles/chapters/tracks directly, the functions
above the buttons are accessed by pressing
SHIFT at the same time as the button.
PGM (SHIFT+1) - Use to program/play a
program list.

10

ZOOM

0
TOP MENU

ECHO

TUNE

HOME
MENU

RPT (SHIFT+2) - Selects a repeat play mode.
RDM (SHIFT+3) - Selects a random play mode.
AUDIO (SHIFT+7) - Selects the audio
channel or language.
SUBTITLE (SHIFT+8) - Selects a subtitle
display.
ANGLE (SHIFT+9) - Changes the camera
angle during DVD multi-angle scene playback.
ZOOM (SHIFT+0) -Changes the zoom level.

DVD
MENU

ST

11
4

ST

ENTER
SOUND
MODE

TUNE

6
SFC

SYSTEM SETUP (SHIFT+HOME MENU)
Use to make various system settings.
Also used to save station presets and select
mono FM reception when using the tuner.

12

KARAOKE

RETURN

7

C

8

SHIFT

CLEAR

MUTE

HOME MENU
Press to display (or exit) the on-screen menu
for Initial Settings, Play Mode functions, etc.

SLEEP

13
DISPLAY

D

1
STANDBY/ON
Switches the player on or into standby.
2 Input source function select
Selects the source you want to listen to; DVD/
CD, TUNER, TAPE or LINE (SHIFT+TAPE).

5 Cursor buttons, ENTER, tuning and karaoke
buttons
Cursor buttons - Use the cursor buttons
(///) to navigate on-screen displays
and menus.
ENTER - Selects an option or executes a
command.
TUNE (+/-) -Tunes the radio.
ST (+/-) - Selects station presets when listening
to the radio.
The karaoke functions are accessed by pressing
SHIFT at the same time as the corresponding
button:
KARAOKE (SHIFT+) - Selects audio
channels for karaoke.
ECHO (SHIFT+) - Changes the echo
level on the karaoke mics.
Key controls  and  (SHIFT+/) Lowers/raises the pitch of the backing track.

E

F

94

XV-GX3
1

2

3

4

5

6

7

8

A

6

SFC
Selects sound modes or custom settings from
from the Sound Field Control.
SOUND MODE (SHIFT+SFC)
Accesses settings in the Sound menu, such
as the tone controls.

7

Range of the remote control unit
The remote control has a range of about 7
meters at an angle of 30˚ of the remote control
control sensor. It may not work properly if:
• There are obstacles between the remote
control and this unit's remote sensor.
• Direct sunlight or fluorescent light is
shining onto the remote sensor.

Playback controls
See Playing discs, Playing cassette
tapes, and Disc playback features for an
explanation of these controls.

• This system is located near a device that
is emitting infrared rays.
• This unit is operated simultaneously with
another infrared remote control unit.

8 SHIFT
Some of the buttons have alternate functions
(they are outlined on the remote control). Press
and hold SHIFT to access these.

B

9 P.BASS
Press to switch on the bass boost.
10 VOLUME
Adjusts the volume level.
11 DVD MENU
Press to display a DVD disc menu, or the
Disc Navigator.

C

TOP MENU (SHIFT+ DVD MENU)
Displays the top menu of a DVD disc in the
play positionóthis may be the same as pressing
pressing DVD MENU.
12 RETURN
Press to return to a previous menu screen.
13 CLEAR
Clears an entry.
MUTE
Mutes the volume.
D

DISPLAY
Switches between information displays.
SLEEP (SHIFT+DISPLAY) – Use for setting
the sleep timer.

E

F

95

XV-GX3
5

6

7

8

1

2

3

4

7 Jigs list
Name
Service Remote Control Unit
DVD Test Disc (DVD-Video)
CD Test Disc
Flexible Cable (27P)
Flexible Cable (25P)
DVD Data Disc
Test Tape
Test Tape
Test Tape

A

B

Jig No.
GGF1381
GGV1025
STD-905
GGD1447
GGD1309
GGV1175
NCT-111 or STD-301
NCT-112 or STD-331E
STD-630 or STD-631

Remarks
adjustment, diagnosis
Check of DVD-Video
Check of CD
diagnosis of DVDM ASSY
diagnosis of DVDM ASSY
diagnosis (ID data setting)
Tape Speed adjustment
Tape Playback adjustment
Normal blank tape

7 Lubricants and Glues list
Name
Lubricating Oil
Daifree
Silicone Adhesive
Screw tight

C

Lubricants and Glues No.
GYA1001
GEM1036
GEM1037
GYL1001

Remarks
refer to "2.4 05 LOADER ASSY"
refer to "2.4 05 LOADER ASSY"
refer to "2.5 TRAVERSE MECHANISM ASSY-S"
refer to "6.2.5 MECHANISM ADJUSTMENT"

Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools:

D

Position to be cleaned

Cleaning tools

Pickup leneses

Cleaning liquid : GEM1004
Cleaning paper : GED-008

Position to be cleaned

Cleaning tools

Cassette heads
Pinch rollers
Capstans

Cleaning paper : GED-008

Position to be cleaned

Cleaning tools

Fans

Cleaning paper : GED-008

E

F

96

XV-GX3
1

2

3

4



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Page Count                      : 96
Page Mode                       : UseThumbs
Page Layout                     : SinglePage
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:8b4178a6-98be-43f1-aefa-ce7e1b628e6d
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Create Date                     : 2005:09:28 13:57:51Z
Modify Date                     : 2005:10:26 14:35:36+09:00
Metadata Date                   : 2005:10:26 14:35:36+09:00
Creator Tool                    : FrameMaker 7.0
Document ID                     : uuid:d53274f2-a3f7-4ad1-9e79-79221265b025
Format                          : application/pdf
Creator                         : PMC
Title                           : RRV3262
Description                     : Linked
Author                          : PMC
Subject                         : Linked

EXIF Metadata provided by EXIF.tools