Xtreme XPRT SNMP Internal Card Brochure
User Manual: Xtreme XPRT-SNMP Internal Card Brochure Xtreme s
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
HARDWARE SPECIFICATIONS NET LOGIC CPU SAMSUNG S3C4510B 16/32-bit RISC microcontroller Memory Flash Memory – 16Mbits SDRAM – 128Mbits Ethernet Connector 10/100 BaseT RJ-45, auto switch Power Input and Consumption 12V DC regulated, power consumption under 3 watts Size 118 mm (L) x 89 mm (W) x 23 mm( H) Network Interface UTP Fast Ethernet 10/100BastT RJ-45, auto-sense Display Power, Diagnostic, TxD and RxD LEDs Serial Port Two high speed RS-232 ports. One used as a console port or connected to a MODEM allowing PPP dial-in and paging, another is golden finger type serial port and connected to UPS Extension Port Connected to an extended device such as environment measurement through I2C Real Time Clock Time can be adjusted by SNTP Firmware Upgradeable Upgrades firmware via a web browser or TFTP Telnet Management Allows management via telnet SNMP Network Management Supports both SNMP v1 and v2. Supports RFC 1213 (MIB-II), RFC 1628 (UPS MIB) , and private UPS extension MIB. Compatible with any standard SNMP NMS such as HP OpenView, IBM NetView Web Network Management Supports HTTP 1.0 protocol. Combined with HTML, JavaScript and Java Applet Setup/Configuration Allows setup via telnet or console Operating Environment 0 to 60ºC SNMP Card SNMP Communications Schematic U 9 PIN 1 T1 D2 J5 U 10 U1 U2 U1: S3C4510B – Samsung 16/32 bits MCU U2: Altima AC101 or AM79C874 – Ethernet Transceiver U9: K4S281632D – 128Mbit SDRAM U10: MX29LV160T – Flash Memory J1: 10/100BaseT RJ-45 Phone Jack J2: Modem or console port J5: Extension Port D2: Power/Diagnostic, Network Tx/Rx LEDs J1 J2 Ordering Information: NET Logic SNMP Card, Model No: XPRT-SNMP1 or XVRT-SNMPB Xtreme Power Conversion Corporation 920 Bay Vista Blvd. • Englewood, Fl 34223 Tel: 800.582.4524 www.xpcc.com DO YOU REQUIRE XTREME SNMP CONNECTIVITY? SNMP (Simple Network Management Protocol) is used widely in the network management field. With the support for SNMP, the .NETpower software user interface turns the UPS into an industrial standard managed network device. You can use an SNMP NMS (such as HP OpenView or a IBM NetView) to manage your UPS over a LAN or the Internet. Moreover, the Net Logic SNMP card will create a standard browser interface for the UPS. This browser interface allows easy viewing, management and control of the UPS. In addition to the network management function, it will notify you when an event occurs, and even shut down multiple systems on the LAN. Information Management • • Network Interface information and status of the UPS locally or remotely. It Serial Port presents the information in graphical formats from different Used as a console port or connected to a MODEM allowing PPP dial-in and paging • Extension Port • Real Time Clock • Setup/Configuration Connected to an extended device such as environment measurement Time can be adjusted by SNTP Allows setup via telnet or console • Firmware Upgradeable • Multiple System Shutdown • Event Notification • SNMP Network Management • The .NETpower interface allows you to view the UTP Fast Ethernet 10/100 auto-sense Upgrades firmware via a web browser or TFTP points of view: inside activity, power meters, and scope charts. The .NETpower interface maintains two log files • an event log file which contains all UPS related events such as power failures, shutdowns, power recoveries, etc. • a data log file: which is a collection of the UPS power quality, including input voltage, output voltage, battery voltage, temperature, etc. Sends a shutdown signal to shut down multiple systems on LAN OnEvent Includes network message, OnEvent multimedia message, email and page OnEvent is a new notification technology which can exchange multimedia Supports SNMP v1.0 and v2.0. Supports RFC 1213 (MIB-II), RFC 1628 (UPS MIB), and private UPS extension MIB. Compatible with any standard SNMP NMS such as HP OpenView and IBM NetView messages over a LAN, regardless of operating system. When a power event Web Network Management the system when receiving a shutdown signal from the NETLogic card. It also occurs, a multimedia message box will be displayed on each computer with OnEvent software installed. It is also a shutdown agent which will shut down Supports HTTP 1.0 protocol. Combined with HTML, Java Script and Java Applet • Telnet Management • Graphic Information Management • Event Logging serves as a shutdown agent when a shutdown signal is received from the .Netlogic card. Allows management via telnet Includes Power Meter, Block Diagram, Power Scope, and Log Analysis Contains all UPS-related events Data Logging A collection of the UPS power quality Flexible Event Action You can define actions for each event. The .NETpower interface will perform actions according to your definitions when an event occurs. The actions include logging, network notification, email, paging, executing command file, and system shutdown. Scheduling Perform shutdown, startup, and self-test according to the scheduling settings Flexible Event Action Provides flexible event action feature Scheduling The .NETpower interface allows for a customizable UPS schedule setup for UPS Control automatic system shutdown/startups and self-tests. UPS Configuration Compatible Operating Systems The SNMP CD is compatible with the following operating systems: FreeBSD, Hpux, IBMaix, IBMos2, IRIX, Linux, Solsparc, Solx86, Windows Allows you to shut down, reset, or restart the UPS remotely Allows you to configure the UPS remotely Password Security Provides password protection www.xpcc.com www.xpcc.com Information Management • • Network Interface information and status of the UPS locally or remotely. It Serial Port presents the information in graphical formats from different Used as a console port or connected to a MODEM allowing PPP dial-in and paging • Extension Port • Real Time Clock • Setup/Configuration Connected to an extended device such as environment measurement Time can be adjusted by SNTP Allows setup via telnet or console • Firmware Upgradeable • Multiple System Shutdown • Event Notification • SNMP Network Management • The .NETpower interface allows you to view the UTP Fast Ethernet 10/100 auto-sense Upgrades firmware via a web browser or TFTP points of view: inside activity, power meters, and scope charts. The .NETpower interface maintains two log files • an event log file which contains all UPS related events such as power failures, shutdowns, power recoveries, etc. • a data log file: which is a collection of the UPS power quality, including input voltage, output voltage, battery voltage, temperature, etc. Sends a shutdown signal to shut down multiple systems on LAN OnEvent Includes network message, OnEvent multimedia message, email and page OnEvent is a new notification technology which can exchange multimedia Supports SNMP v1.0 and v2.0. Supports RFC 1213 (MIB-II), RFC 1628 (UPS MIB), and private UPS extension MIB. Compatible with any standard SNMP NMS such as HP OpenView and IBM NetView messages over a LAN, regardless of operating system. When a power event Web Network Management the system when receiving a shutdown signal from the NETLogic card. It also occurs, a multimedia message box will be displayed on each computer with OnEvent software installed. It is also a shutdown agent which will shut down Supports HTTP 1.0 protocol. Combined with HTML, Java Script and Java Applet • Telnet Management • Graphic Information Management • Event Logging serves as a shutdown agent when a shutdown signal is received from the .Netlogic card. Allows management via telnet Includes Power Meter, Block Diagram, Power Scope, and Log Analysis Contains all UPS-related events Data Logging A collection of the UPS power quality Flexible Event Action You can define actions for each event. The .NETpower interface will perform actions according to your definitions when an event occurs. The actions include logging, network notification, email, paging, executing command file, and system shutdown. Scheduling Perform shutdown, startup, and self-test according to the scheduling settings Flexible Event Action Provides flexible event action feature Scheduling The .NETpower interface allows for a customizable UPS schedule setup for UPS Control automatic system shutdown/startups and self-tests. UPS Configuration Compatible Operating Systems The SNMP CD is compatible with the following operating systems: FreeBSD, Hpux, IBMaix, IBMos2, IRIX, Linux, Solsparc, Solx86, Windows Allows you to shut down, reset, or restart the UPS remotely Allows you to configure the UPS remotely Password Security Provides password protection www.xpcc.com www.xpcc.com HARDWARE SPECIFICATIONS NET LOGIC CPU SAMSUNG S3C4510B 16/32-bit RISC microcontroller Memory Flash Memory – 16Mbits SDRAM – 128Mbits Ethernet Connector 10/100 BaseT RJ-45, auto switch Power Input and Consumption 12V DC regulated, power consumption under 3 watts Size 118 mm (L) x 89 mm (W) x 23 mm( H) Network Interface UTP Fast Ethernet 10/100BastT RJ-45, auto-sense Display Power, Diagnostic, TxD and RxD LEDs Serial Port Two high speed RS-232 ports. One used as a console port or connected to a MODEM allowing PPP dial-in and paging, another is golden finger type serial port and connected to UPS Extension Port Connected to an extended device such as environment measurement through I2C Real Time Clock Time can be adjusted by SNTP Firmware Upgradeable Upgrades firmware via a web browser or TFTP Telnet Management Allows management via telnet SNMP Network Management Supports both SNMP v1 and v2. Supports RFC 1213 (MIB-II), RFC 1628 (UPS MIB) , and private UPS extension MIB. Compatible with any standard SNMP NMS such as HP OpenView, IBM NetView Web Network Management Supports HTTP 1.0 protocol. Combined with HTML, JavaScript and Java Applet Setup/Configuration Allows setup via telnet or console Operating Environment 0 to 60ºC SNMP Card SNMP Communications Schematic U 9 PIN 1 T1 D2 J5 U 10 U1 U2 U1: S3C4510B – Samsung 16/32 bits MCU U2: Altima AC101 or AM79C874 – Ethernet Transceiver U9: K4S281632D – 128Mbit SDRAM U10: MX29LV160T – Flash Memory J1: 10/100BaseT RJ-45 Phone Jack J2: Modem or console port J5: Extension Port D2: Power/Diagnostic, Network Tx/Rx LEDs J1 J2 Ordering Information: NET Logic SNMP Card, Model No: XPRT-SNMP1 or XVRT-SNMPB Xtreme Power Conversion Corporation 920 Bay Vista Blvd. • Englewood, Fl 34223 Tel: 800.582.4524 www.xpcc.com DO YOU REQUIRE XTREME SNMP CONNECTIVITY? SNMP (Simple Network Management Protocol) is used widely in the network management field. With the support for SNMP, the .NETpower software user interface turns the UPS into an industrial standard managed network device. You can use an SNMP NMS (such as HP OpenView or a IBM NetView) to manage your UPS over a LAN or the Internet. Moreover, the Net Logic SNMP card will create a standard browser interface for the UPS. This browser interface allows easy viewing, management and control of the UPS. In addition to the network management function, it will notify you when an event occurs, and even shut down multiple systems on the LAN.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 Instance ID : uuid:cc85ada0-2ffb-11dd-a19a-0017f2caae84 Document ID : adobe:docid:indd:90feb6e1-a179-11dc-866e-8ac0b2af38a3 Rendition Class : proof:pdf Derived From Instance ID : 90feb6e0-a179-11dc-866e-8ac0b2af38a3 Derived From Document ID : adobe:docid:indd:90feb6df-a179-11dc-866e-8ac0b2af38a3 Manifest Link Form : ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 300.00 Manifest Placed Y Resolution : 72.00, 300.00 Manifest Placed Resolution Unit : Inches, Inches Manifest Reference Instance ID : uuid:33d9c180-a40b-11dc-b5e3-0017f2caae84, uuid:3FFCE4FD136911DDB869DAABEC2B958B Manifest Reference Document ID : uuid:DABEC8BFA25911DC83E7ED9FE08DDB58, uuid:9EA01BB7136211DD855BF39C4AD93BE2 Create Date : 2008:06:01 09:48:30-07:00 Modify Date : 2008:06:01 09:57:20-07:00 Metadata Date : 2008:06:01 09:57:20-07:00 Creator Tool : Adobe InDesign CS2 (4.0.5) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 8598 bytes, use -b option to extract) Format : application/pdf Producer : Adobe PDF Library 7.0 Trapped : False Page Count : 4 Creator : Adobe InDesign CS2 (4.0.5)EXIF Metadata provided by EXIF.tools