Arctic_cat_2012_450_1000_service_manual Arctic Cat 2012 450 1000 Service Manual

User Manual: arctic_cat_2012_450_1000_service_manual

Open the PDF directly: View PDF .
Page Count: 210

Download
Open PDF In Browser	View PDF

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

FOREWORD
This Arctic Cat Service Manual contains service, maintenance, and troubleshooting information for certain 2012
Arctic Cat ATV models (see cover). The complete manual is designed to aid service personnel in service-oriented
applications.
Arctic Cat offers additional publications (when they become available) to aid in servicing other ATV models. To
service models not included in this manual, please refer to the following publications:
•
•
•
•
•
•
•
•
•

2012 Y-12+ Service Manual
2012 T-14 Service Manual
2012 300 DVX/Utility Service Manual
2012 350 Service Manual
2012 425 Service Manual
2012 700 Diesel Service Manual
2012 450 XC Service Manual
2012 650 Service Manual
2012 550/700 Service Manual

This manual is divided into sections. Each section covers a specific ATV component or system and, in addition to
the standard service procedures, includes disassembling, inspecting, and assembling instructions. When using this
manual as a guide, the technician should use discretion as to how much disassembly is needed to correct any given
condition.
The service technician should become familiar with the operation and construction of each component or system
by carefully studying the complete manual. This manual will assist the service technician in becoming more aware
of and efficient with servicing procedures. Such efficiency not only helps build consumer confidence but also saves
time and labor.
All Arctic Cat ATV publications and decals display the words Warning, Caution, Note, and At This Point to
emphasize important information. The symbol ! WARNING identifies personal safety-related information.
Be sure to follow the directive because it deals with the possibility of severe personal injury or even death. A
CAUTION identifies unsafe practices which may result in ATV-related damage. Follow the directive because it
deals with the possibility of damaging part or parts of the ATV. The symbol  NOTE: identifies supplementary
information worthy of particular attention. The symbol  AT THIS POINT directs the technician to certain
and specific procedures to promote efficiency and to improve clarity.
At the time of publication, all information, photographs, and illustrations were technically correct. Some photographs used in this manual are used for clarity purposes only and are not designed to depict actual conditions.
Because Arctic Cat Inc. constantly refines and improves its products, no retroactive obligation is incurred.
All materials and specifications are subject to change without notice.
Keep this manual accessible in the shop area for reference.
Product Service and
Warranty Department
Arctic Cat Inc.

www.mymowerparts.com

August 2011

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Click on the blue text to go.

Service
S
erv
ervice
rvice M
Manual
anual

TABLE OF CONTENTS

A V

Note: To navigate through this manual, use the PAGE UP/PAGE DOWN buttons on the keyboard, click on the
Table of Contents bookmarks on the left side of the screen, or click the blue text below. To return to this page,
click the Manual Table of Contents button at the bottom of each page.

'PSFXPSE
1.

General Information/Specifications

Periodic Maintenance

Engine/Transmission

Fuel/Lubrication/Cooling

Electrical System

Drive System/Brake System

Suspension

Steering/Frame

45
4
50
50 Mo
M
Mode
Mod
od
o
de
d
del
els
s
110
1000
00
000
0
00
0
0 Mo
Mode
M
Mod
od
o
de
d
del
ells
s
SHARE OUR PASSION.

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

SECTION 1 - GENERAL INFORMATION/
SPECIFICATIONS

TABLE OF CONTENTS
General Specifications ............................................ 1-2
Torque Specifications .............................................. 1-3
Torque Conversions (ft-lb/N-m) ............................... 1-4
Break-In Procedure ................................................. 1-4
Gasoline - Oil - Lubricant ........................................ 1-5
Genuine Parts ......................................................... 1-5
Preparation For Storage.......................................... 1-6
Preparation After Storage........................................ 1-6

www.mymowerparts.com

1-1

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

General Specifications

1000
CHASSIS
Brake Type
Tire Size

450
CHASSIS
Brake Type

Hydraulic w/Brake Lever
Lock and Auxiliary Brake
Front - 25 x 8-12
Rear - 25 x 10-12
0.35 kg/cm² (5 psi)

Tire Size
Tire Inflation Pressure

MISCELLANY
Spark Plug Type
Spark Plug Gap
Gas Tank Capacity
Coolant Capacity
Rear Drive Capacity
Front Differential Capacity
Engine Oil Capacity (approx)

Gasoline (recommended)
Engine Oil (recommended)
Differential/Rear Drive Lubricant
Drive Belt Width (minimum)
Brake Fluid
Taillight/Brakelight
Headlight

NGK CR7E
0.7-0.8 mm (0.028-0.031 in.)
21.6 L (5.7 U.S. gal.) - FIS
20.0 L (5.3 U.S. gal.) - TRV
2.9 L (3.0 U.S. qt)
250 ml (8.5 fl oz)*
275 ml (9.3 fl oz)**
2.85 L (3.0 U.S. qt) Overhaul
2.50 L (2.6 U.S. qt) - Change
87 Octane Regular
Unleaded
Arctic Cat ACX All Weather
(Synthetic)
SAE Approved 80W-90
Hypoid
28.5 mm (1.12 in.)
DOT 4
12V/8W/27W
12V/37W (2)

(Mud Pro)
(Mud Pro)
(Cruiser)
(Cruiser)
Tire Inflation Pressure

MISCELLANY
Spark Plug Type
Spark Plug Gap
Gas Tank Capacity

Coolant Capacity
Differential Capacity
Rear Drive Capacity
Engine Oil
Capacity (approx)
Gasoline (recommended)
Engine Oil (recommended)
Front Differential/Rear Drive Lubricant
Drive Belt Width (minimum)
Brake Fluid
Taillight/Brakelight
Headlight

ELECTRICAL SYSTEM
Ignition Timing
Spark Plug Cap
Ignition Coil
Resistance

(primary)
(secondary)

Ignition Coil Primary Voltage
Stator Coil (crankshaft position sensor)
Resistance
(AC generator)
Crankshaft Position Sensor AC Voltage
AC Generator Output

(no load)

10° BTDC @ 1500 RPM
5000 ohms
Less than 5.0 ohms
(terminal (+) to terminal (-))
12k-19k ohms (high tension plug cap - to terminal (+))
Battery Voltage
(orange (+) to blue/white(-))
150-250 ohms (blue to
green)
Less than 1 ohm (yellow to
yellow)
2.0 volts or more (blue to
green)
75 AC volts @ 5000 RPM
(yellow to yellow)

Hydraulic w/Brake Lever
Lock and Auxiliary Brake
Front - 25 x 9-12
Rear - 25 x 11-12
Front - 28 x 9-14
Rear - 28 x 11-14
Front - 25 x 8-12
Rear - 25 x 10-12
0.35 kg/cm² (5 psi) - Mud Pro
0.49 kg/cm² (7 psi) - TRV/
Cruiser
NGK CPR8E
0.5-0.6 mm (0.019-0.024 in.)
21.6 L (5.7 U.S. gal.) - FIS
20.0 L (5.3 U.S. gal.) Cruiser/TRV
3.3 L (3.5 U.S. qt)
275 ml (9.3 fl oz)*
250 ml (8.5 fl oz)**
2.6 L (2.75 U.S. qt) Overhaul
1.9 L (2.0 U.S. qt) - Change
87 Octane Regular
Unleaded
Arctic Cat ACX All Weather
(Synthetic)
SAE Approved 80W-90
Hypoid
35.6 mm (1.40 in.)
DOT 4
12V/8W/27W
12V/27W (2)

ELECTRICAL SYSTEM
Ignition Timing
Spark Plug Cap
Ignition Coil
Resistance

(primary)
(secondary)

Ignition Coil
Primary Voltage
Stator Coil (crankshaft position sensor)
Resistance
(AC generator)
Crankshaft Position Sensor
AC Voltage
Generator Output

(no load)

10° BTDC @ 1500 RPM
5000 ohms
4.8 ohms (terminal (+) to
terminal (-))
12k-19k ohms (high tension plug cap to terminal)
Battery Voltage
(orange to ground)
150-250 ohms (blue to
green)
Less than 1 ohm (gray to
gray)
2.0 volts or more
(blue to green)
75 AC volts or more
@ 5000 RPM (black to black)

Specifications subject to change without notice.
* One inch below plug threads.
** At the plug threads.

1-2

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
DRIVE TRAIN COMPONENTS
(450)

Torque Specifications

Part
EXHAUST COMPONENTS
Part

Part Bolted To

Torque
ft-lb N-m

Part Bolted To

Torque
ft-lb N-m

Engine Mounting Through-Bolt Frame

Front Differential

Frame/Differential
Bracket

Output Flange

Rear Flange Output
Joint

Pinion Housing

Differential Housing

Differential Housing Cover***

Differential Housing

Drive Bevel Gear Nut**

Shaft

Lock Collar

Differential Housing

125

169

200

272

Exhaust Pipe

Engine

Spark Arrester

Muffler

48
in.-lb

5.5

Engine/Harness Ground Cap Crankcase
Screw

Hub Hex Nut

Shaft/Axle (max)

Coil

Oil Drain Plug

Front Differential/Rear
45
Drive
in.-lb

Frame

Oil Fill Plug

Front Differential/Rear
Drive

Steering Post Bearing Flange Frame

Oil Drain Plug

Engine

Lower Steering Bearing
Washer Cap Screw***

Steering Post

Rear Drive Input Shaft/Housing Differential Housing

Wheel (Steel)

Hub

Tie Rod End

Knuckle/Steering Post

Wheel (Aluminum)

Hub

108

Frame

Rear Drive Gear Case

Frame

Engine Output Shaft**

Rear Gear Case Input
Flange

ELECTRICAL COMPONENTS

Air Filter Housing

STEERING COMPONENTS
Steering Post Bearing
Housing

EPS Housing

BRAKE COMPONENTS
Brake Disc*

Hub

Brake Hose

Caliper

Brake Hose (Banjo-Fitting)

Master Cylinder

Brake Hose

Auxiliary Brake Cylinder 20

ENGINE/TRANSMISSION
(450)
Clutch Shoe**

Crankshaft

147

199

Crankcase

Master Cylinder (Rear)

Frame

Clutch Cover/Housing
Assembly

Hydraulic Caliper

Knuckle
(w/“Patch-Lock”)

Left-Side Cover

Crankcase

Crankcase Half (6 mm)

Crankcase Half

13.5

Crankcase Half (8 mm)

Crankcase Half

Cylinder Nut

Crankcase Half

Cylinder Head (Cap Screw)

Crankcase

Cylinder Head Nut

Cylinder

Master Cylinder Clamp

Master Cylinder

Brake Pedal

Brake Pedal Axle

CHASSIS COMPONENTS
Footrest
Footrest

Frame (8 mm)

Frame (10 mm)

SUSPENSION COMPONENTS (Front)
A-Arm

Frame

Knuckle

Ball Joint

Shock Absorber

Frame/Upper A-Arm

Knuckle

A-Arm

Frame

Shock Absorber (Lower)

Lower A-Arm

A-Arm

Frame

Knuckle (450)

A-Arm

Knuckle (1000)

A-Arm

SUSPENSION COMPONENTS (Rear)
Shock Absorber (Upper)

Valve Cover****

Cylinder Head

Oil Pump Drive Gear**

Crankshaft

Driven Pulley Nut**

Driveshaft

147

199

Ground Cable

Engine

Output Shaft Flange Nut

Output Shaft

Magneto Rotor Nut

Crankshaft

107

146

Cam Sprocket**

Camshaft

Cam Chain Tensioner Guide

Cylinder

Stator Coil**

Crankcase

Starter Motor

Crankcase

V-Belt Cover

Crankcase

Valve Adjuster Jam Nut

Valve Adjuster

9.5

Oil Fitting

Engine

Oil Pump**

Crankcase

Tappet Cover

Valve Cover

Cam Chain Tensioner

Cylinder

13.5

Magneto Cover

Crankcase

Rear Driveline

Output Drive Flange

Starter One-Way Clutch**

Flywheel

Movable Drive Face Nut**

Clutch Shaft

147

199

Water Pump Cover/Housing

Magneto Cover

Water Pump Drive Gear

Crankshaft

* w/Blue Loctite #243
** w/Red Loctite #271
*** w/Green Loctite #609
**** w/Three Bond Sealant

www.mymowerparts.com

1-3

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
DRIVE TRAIN COMPONENTS (1000)
Part
Engine Mount (Rear)
Front Differential
Rear Gear Case
Pinion Housing
Differential Housing Cover***
Lock Collar
Hub Nut
Oil Drain Plug
Oil Fill Plug
Oil Drain Plug
Wheel (Steel)
Wheel (Aluminum)
Rear Drive Input Shaft/Housing
Rear Output Drive Flange
Shift Cam Stopper
Shift Cam Plate
Shifter Housing
Engine Output Shaft**

Part Bolted To
Frame
Frame/Differential
Bracket
Frame
Differential Housing
Differential Housing
Differential Housing
Shaft/Axle (max)
Front Differential/
Rear Drive
Front Differential/
Rear Drive
Engine
Hub
Hub
Differential Housing
Rear Yoke Flange
Shift Stopper
Shift Cam Shaft
Crankcase
Rear Gear Case
Input Flange

45
38

61
52

38
52
23
31
23
31
125 169
200 272
45
5
in.-lb
16
22
16
40
80
23
20
8
8
8
20

22
54
108
31
27
11
11
11
27

ENGINE/TRANSMISSION (1000)
Clutch Shoe**
Clutch Cover/Housing Assembly
Crankcase Half
Crankcase Lower Cover (6 mm)
Crankcase Lower Cover (8 mm)
Cylinder Head (Cap Screw)
Cylinder Head (6 mm)
Cylinder Head (8 mm)
Cylinder Head Cover
Driven Pulley Nut**
Ground Wire
Magneto Cover
Oil Filler Cover
Speed Sensor Housing
Starter Motor
V-Belt Housing
Intake Manifold
Output Shaft Yoke Nut
Rotor/Flywheel Nut
Cam Sprocket**
V-Belt Cover
Movable Drive Face Nut**
Oil Pump Cover*
Oil Strainer Cap
Shift Cam Stopper
Shift Cam Stopper Spring
Shift Cam Plate
Shifter Housing
Secondary Drive Gear Nut
Starter One-Way Clutch**
Output Yoke Nut

* w/Blue Loctite #243
** w/Red Loctite #271
*** w/Green Loctite #609
**** w/Three Bond Sealant

1-4

www.mymowerparts.com

Crankshaft
Crankcase
Crankcase Half
Crankcase
Crankcase
Crankcase
Cylinder
Cylinder
Cylinder Head
Driveshaft
Engine
Crankcase
Crankcase
Crankcase
Crankcase
Crankcase
Cylinder
Output Shaft
Crankshaft
Camshaft
Clutch Cover
Clutch Shaft
Crankcase
Crankcase
Crankcase
Shift Cam Stopper
Shift Cam Shaft
Crankcase
Gear
Flywheel
Output Shaft

Torque Conversions
(ft-lb/N-m)

Torque
ft-lb N-m

221
8
8
8
20
37
8
18
8.5
80
8
8
8
8
8
8
8
59
107
10
8
165
8
8
8
8
8
8
74
26
74

300
11
11
11
27
50
11
24
11.5
108
11
11
11
11
11
11
11
80
145
13.5
11
224
11
11
11
11
11
11
100
35
100

ft-lb

N-m

ft-lb

N-m

ft-lb

N-m

ft-lb

N-m

1.4

35.4

69.4

103.4

2.7

36.7

70.7

104.7

4.1

38.1

72.1

106.1

5.4

39.4

73.4

107.4

6.8

40.8

74.8

108.8

8.2

42.2

76.2

110.2

9.5

43.5

77.5

111.5

10.9

44.9

78.9

112.9

12.2

46.2

80.2

114.2

13.6

47.6

81.6

115.6

117

16.3

50.3

84.3

118.3

17.7

51.7

85.7

119.7

121

20.4

54.4

88.4

122.4

21.8

55.8

89.8

123.8

23.1

57.1

91.1

125.1

24.5

58.5

92.5

126.5

25.8

59.8

93.8

127.8

27.2

61.2

95.2

129.2

28.6

62.6

96.6

130.6

29.9

63.9

97.9

131.9

31.3

65.3

99.3

133.3

32.6

66.6

100.6

134.6

102

100

136

Break-In Procedure
A new ATV and an overhauled ATV engine require a
“break-in” period. The first 10 hours (or 200 miles) are
most critical to the life of this ATV. Proper operation during this break-in period will help assure maximum life
and performance from the ATV.
During the first 10 hours (or 200 miles) of operation,
always use less than 1/2 throttle. Varying the engine
RPM during the break-in period allows the components
to “load” (aiding the mating process) and then “unload”
(allowing components to cool). Although it is essential to
place some stress on the engine components during
break-in, care should be taken not to overload the engine
too often. Do not pull a trailer or carry heavy loads during the 10-hour break-in period.
When the engine starts, allow it to warm up properly. Idle
the engine several minutes until the engine has reached
normal operating temperature. Do not idle the engine for
excessively long periods of time.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
During the break-in period, a maximum of 1/2 throttle is
recommended; however, brief full-throttle accelerations
and variations in driving speeds contribute to good
engine break-in.

RECOMMENDED FRONT
DIFFERENTIAL/REAR DRIVE
LUBRICANT

After the completion of the break-in period, the engine
oil and oil filter should be changed. Other maintenance
after break-in should include checking of all prescribed
adjustments and tightening of all fasteners (see Periodic
Maintenance Chart in Section 2).

The recommended lubricant is Arctic Cat Gear Lube or
an equivalent gear lube which is SAE approved 80W-90
hypoid. This lubricant meets all of the lubrication
requirements of the Arctic Cat ATV front differentials
and rear drives.

CAUTION

Gasoline - Oil - Lubricant
RECOMMENDED GASOLINE

Any lubricant used in place of the recommended lubricant could cause serious front differential/rear drive
damage.

FILLING GAS TANK

The recommended gasoline to use is 87 minimum octane
regular unleaded. In many areas, oxygenates (either ethanol or MTBE) are added to the gasoline. Oxygenated
gasolines containing up to 10% ethanol, 5% methane, or
5% MTBE are acceptable gasolines.
When using ethanol blended gasoline, it is not necessary
to add a gasoline antifreeze since ethanol will prevent the
accumulation of moisture in the fuel system.

CAUTION
Do not use white gas. Only Arctic Cat approved gasoline additives should be used.

! WARNING
Always fill the gas tank in a well-ventilated area. Never
add fuel to the ATV gas tank near any open flames or
with the engine running. DO NOT SMOKE while filling
the gas tank.

Since gasoline expands as its temperature rises, the gas
tank must be filled to its rated capacity only. Expansion
room must be maintained in the tank particularly if the
tank is filled with cold gasoline and then moved to a
warm area.

RECOMMENDED ENGINE/
TRANSMISSION OIL

CAUTION
Any oil used in place of the recommended oil could
cause serious engine damage. Do not use oils which
contain graphite or molybdenum additives. These oils
can adversely affect clutch operation. Also, not recommended are racing, vegetable, non-detergent, and castor-based oils.

The recommended oil to use is Arctic Cat ACX All
Weather synthetic engine oil, which has been specifically
formulated for use in this Arctic Cat engine. Although
Arctic Cat ACX All Weather synthetic engine oil is the
only oil recommended for use in this engine, use of any
API certified SM 0W-40 oil is acceptable.

ATV0049B

! WARNING
Do not overflow gasoline when filling the gas tank. A
fire hazard could materialize. Always allow the engine to
cool before filling the gas tank.

! WARNING
Do not over-fill the gas tank.

Tighten the gas tank cap securely after filling the tank.

Genuine Parts

OILCHARTJ

www.mymowerparts.com

When replacement of parts is necessary, use only genuine
Arctic Cat ATV parts. They are precision-made to ensure
high quality and correct fit. Refer to the appropriate Illustrated Parts Manual for the correct part number, quantity,
and description.

1-5

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
9. Store the ATV indoors in a level position.

Preparation For Storage

CAUTION

Avoid storing outside in direct sunlight and avoid using
a plastic cover as moisture will collect on the ATV causing rusting.

Prior to storing the ATV, it must be properly serviced to
prevent rusting and component deterioration.

Arctic Cat recommends the following procedure to prepare the ATV for storage.

1. Clean the seat cushion (cover and base) with a
damp cloth and allow it to dry.
2. Clean the ATV thoroughly by washing dirt, oil,
grass, and other foreign matter from the entire
ATV. Allow the ATV to dry thoroughly. DO NOT
get water into any part of the engine or air intake.
3. Either drain the gas tank or add Fuel Stabilizer to
the gas in the gas tank. Remove the air filter housing cover and air filter. Start the engine and allow
it to idle; then using Arctic Cat Engine Storage
Preserver, rapidly inject the preserver into the air
filter opening for a period of 10 to 20 seconds.
Stop the engine. Install the air filter and housing
cover.
CAUTION
If the interior of the air filter housing is dirty, clean the
area before starting the engine.

4. Plug the exhaust hole in the exhaust system with a
clean cloth.
5. Apply light oil to the upper steering post bushing
and plungers of the shock absorbers.
6. Tighten all nuts, bolts, cap screws, and screws.
Make sure rivets holding components together are
tight. Replace all loose rivets. Care must be taken
that all calibrated nuts, cap screws, and bolts are
tightened to specifications.
7. Fill the cooling system to the bottom of the stand
pipe in the radiator neck with properly mixed
coolant.
8. Disconnect the battery cables; then remove the
battery, clean the battery posts and cables, and
store in a clean, dry area.

Preparation After
Storage
Taking the ATV out of storage and correctly preparing it
will assure many miles and hours of trouble-free riding.
Arctic Cat recommends the following procedure to prepare the ATV.

1. Clean the ATV thoroughly.
2. Clean the engine. Remove the cloth from the
exhaust system.
3. Check all control wires and cables for signs of
wear or fraying. Replace if necessary.
4. Change the engine/transmission oil and filter.
5. Check the coolant level and add properly mixed
coolant as necessary.
6. Charge the battery; then install. Connect the battery cables.
CAUTION
The ignition switch must be in the OFF position prior to
installing the battery or damage may occur to the ignition system.

CAUTION
Connect the positive battery cable first; then the negative.

7. Check the entire brake systems (fluid level, pads,
etc.), all controls, headlights, taillight, brakelight,
and headlight aim; adjust or replace as necessary.
8. Tighten all nuts, bolts, cap screws, and screws
making sure all calibrated nuts, cap screws, and
bolts are tightened to specifications.
9. Check tire pressure. Inflate to recommended pressure as necessary.
10. Make sure the steering moves freely and does not
bind.
11. Check the spark plug(s). Clean or replace as necessary.

1-6

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

SECTION 2 PERIODIC MAINTENANCE

TABLE OF CONTENTS
Periodic Maintenance Chart.................................... 2-2
Periodic Maintenance.............................................. 2-3
Lubrication Points.................................................... 2-3
Air Filter................................................................... 2-3
Valve/Tappet Clearance .......................................... 2-4
Testing Engine Compression .................................. 2-5
Spark Plug(s) .......................................................... 2-5
Muffler/Spark Arrester ............................................. 2-6
Engine/Transmission Oil - Filter - Strainer .............. 2-6
Liquid Cooling System ............................................ 2-7
Front Differential/Rear Drive Lubricant .................... 2-9
Nuts/Bolts/Cap Screws............................................ 2-9
Headlights/Taillight-Brakelight ................................. 2-9
Shift Lever ............................................................. 2-11
Hydraulic Brake Systems ...................................... 2-11
Burnishing Brake Pads.......................................... 2-13
Checking/Replacing V-Belt.................................... 2-13

www.mymowerparts.com

2-1

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
A = Adjust
C = Clean
D = Drain

Periodic Maintenance
Chart

Item
Battery

Initial Service
Every
Every 3
After Break-In Every Month or Months or
(First Month or Day Every 100 Every 300
100 Miles)
Miles
Miles
I
I

Valve/Tappet Clearance

Every 6
Every Year
Months or
or Every
Every 500
1500 Miles
Miles

Fuses
Air Filter

I = Inspect
L = Lubricate
R = Replace
T = Tighten

C
I

R
I

Engine Compression
Spark Plug(s)

A
I

Muffler/Spark Arrester

R
(4000 Mi or 18 Mo)
C

Gas/Vent Hoses

Throttle Cable

Engine-Transmission Oil Level
Engine-Transmission Oil/Filter

R (2 Yrs)

C-L

A-R

R*/R**/R***

Oil Strainer
Front Differential/Rear Drive Lubricant

As Needed

C
I

Tires/Air Pressure

Steering Components

V-Belt

Suspension (Ball joint boots, drive axle
boots front and rear, tie rods,
differential and rear drive bellows)

Nuts/Cap Screws/Screws

R (4 Yrs)
R
I

R
l

Ignition Timing

Headlight/Taillight-Brakelight

Switches

R
R

Shift Lever

Handlebar Grips

A-L

Handlebar

Gauges/Indicators

Frame/Welds/Racks

Electrical Connections

Complete Brake System (Hydraulic &
Auxiliary)

Brake Pads

Brake Fluid

R (2 Yrs)

Brake Hoses

R (4 Yrs)

Coolant/Cooling System

R
l
l

C
L-R

R (2 Yrs)

* Service/Inspect more frequently when operating in adverse conditions.
** When using an API certified SM 0W-40 oil.
*** When using Arctic Cat ACX All Weather synthetic oil, oil change interval can be increased to every 1,000 miles or every year.

2-2

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
450

Periodic Maintenance
This section has been organized into sub-sections which
show common maintenance procedures for the Arctic Cat
ATV.
NOTE: Arctic Cat recommends the use of new gaskets, lock nuts, and seals and lubricating all internal
components when servicing the engine/transmission.
NOTE: Some photographs and illustrations used in
this section are used for clarity purposes only and
are not designed to depict actual conditions.

FI515

1000

NOTE: Critical torque specifications are located in
Section 1.

SPECIAL TOOLS
A number of special tools must be available to the technician when performing service procedures in this section.
Description

p/n

Compression Tester Kit

0444-213

Oil Filter Wrench

0644-389

Tachometer

0644-275

GZ019

Timing Light

0644-296

Valve Clearance Adjuster

0444-255

4. Fill a wash pan larger than the element with a
non-flammable solvent; then dip the element in the
solvent and wash it.

NOTE: Special tools are available from the Arctic
Cat Service Department.

Lubrication Points
It is advisable to lubricate certain components periodically to ensure free movement. Apply light oil to the
components using the following list as reference.
A. Throttle Lever Pivot
B. Brake Lever Pivot
C. Auxiliary Brake Pedal Pivot

Air Filter
Use the following procedure to remove the filter and
inspect and/or clean it.
1. Remove the fasteners securing the storage compartment and remove the storage compartment.
2. Remove the air filter housing cover and the air filter/frame assembly.
3. Remove the foam element from the frame making
sure not to tear the element.

www.mymowerparts.com

NOTE: Foam Air Filter Cleaner and Foam Air Filter
Oil are available from Arctic Cat.

5. Squeeze the element by pressing it between the
palms of both hands to remove excess solvent. Do
not twist or ring the element or it will develop
cracks.
6. Dry the element.
7. Put the element in a plastic bag; then pour in air filter
oil and work the oil into the element.
8. Squeeze the element to remove excess oil.

CAUTION
A torn air filter can cause damage to the ATV engine.
Dirt and dust may get inside the engine if the element is
torn. Carefully examine the element for tears before and
after cleaning it. Replace the element with a new one if it
is torn.

9. Clean any dirt or debris from inside the air cleaner.
10. Install the air filter/frame assembly and cover.
11. Install the storage compartment and cover.
CHECKING AND CLEANING DRAINS
1. Inspect the drains beneath the main housing for
debris and for proper sealing.

2-3

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Feeler Gauge Procedure
Using a feeler gauge, check each valve/tappet
clearance. If clearance is not within specifications, loosen the jam nut and rotate the tappet
adjuster screw until the clearance is within specifications. Tighten each jam nut securely after
completing the adjustment.

CAUTION

KX045A

The feeler gauge must be positioned at the same angle
as the valve and valve adjuster for an accurate measurement of clearance. Failure to measure the valve clearance accurately could cause valve component damage.

2. Replace any drain that is cracked or shows any signs
of hardening or deterioration.

VALVE/TAPPET CLEARANCE

CAUTION

450

0.08-0.12 mm (0.003-0.005 in.) - Intake
0.15-0.20 mm (0.006-0.008 in.) - Exhaust

The drain to the right is the clean air section of the filter
housing. Any leak of this drain will allow dirt into the
engine intake causing severe engine damage.

1000

0.08-0.12 mm (0.003-0.005 in.) - Intake
0.13-0.17 mm (0.005-0.007 in.) - Exhaust

3. Wipe any accumulation of oil or gas from the filter
housing and drains.

Valve/Tappet Clearance
To check and adjust valve/tappet clearance, use the following procedure.
1. Remove the timing inspection plug; then remove the
tappet covers and spark plug(s) (for more detailed
information, see Section 3 - Servicing Top-Side
Components).
NOTE: On the 1000 models, remove the crankshaft
end cap and install the special cap screw (left-hand
threads) to rotate the engine.

CC007DC

B. On the 1000 models, rotate the engine 270° to the
TDC position of the rear cylinder; then repeat step
A.

2. Rotate the crankshaft to the TDC position on the
compression stroke (front cylinder on the 1000 models).

GZ059

Valve Adjuster Procedure

GZ063

NOTE: At this point, the rocker arms and adjuster
screws must not have pressure on them.

2-4

www.mymowerparts.com

NOTE: The seat, storage compartment cover
assembly, compartment box, air filter/filter housing,
and left-side/right-side splash panels must be
removed for this procedure.

A. Place Valve Clearance Adjuster onto the jam nut
securing the tappet adjuster screw; then rotate the
valve adjuster dial clockwise until the end is
seated in the tappet adjuster screw.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
B. While holding the valve adjuster dial in place, use
the valve adjuster handle and loosen the jam nut;
then rotate the tappet adjuster screw clockwise
until friction is felt.
C. Align the valve adjuster handle with one of the
marks on the valve adjuster dial.
D. While holding the valve adjuster handle in place,
rotate the valve adjuster dial counterclockwise
until proper valve/tappet clearance is attained.
NOTE: Refer to the appropriate specifications in
Feeler Gauge Procedure sub-section for the proper
valve/tappet clearance.
NOTE: Rotating the valve adjuster dial counterclockwise will open the valve/tappet clearance by
0.05 mm (0.002 in.) per mark.

E. While holding the adjuster dial at the proper
clearance setting, tighten the jam nut securely
with the valve adjuster handle.
F. Rotate the engine 270° to the TDC position of the
rear cylinder; then repeat steps A-E for the rear
cylinder.
3. Install the timing inspection plug; then on the 1000
models, remove the cap screw and install the crankcase end cap.
4. Place the tappet covers into position making sure the
proper cap screws are with the proper cover. Tighten
the cap screws securely.
5. Install the spark plug(s).

Testing Engine
Compression

5. While holding the throttle lever in the full-open position, crank the engine over with the electric starter
until the gauge shows a peak reading (five to 10
compression strokes).
Model

COMPRESSION
PSI Hot (WOT)

PSI Cold (WOT)

450

95-115

N/A

1000 (Front)

125-145

80-120

1000 (Rear)

165-185

150-190

6. If compression is abnormally low, inspect the
following items.
A. Verify starter cranks engine over at normal speed
(approximately 400 RPM).
B. Gauge functioning properly.

C. Throttle lever in the full-open position.
D. Valve/tappet clearance correct.
E. Engine warmed up.
F. Intake not restricted.
NOTE: To service valves, see Section 3.

7. Pour 29.5 ml (1 fl oz) of oil into the spark plug hole,
reattach the gauge, and retest compression.
8. If compression is now evident, service the piston
rings (see Section 3).

Spark Plug(s)
A light brown insulator indicates that a plug is correct. A
white or dark insulator indicates that the engine may need
to be serviced. To maintain a hot, strong spark, keep the
plug free of carbon.

To test engine compression, use the following procedure.
1. Remove the high tension lead(s) from the spark
plug(s).
2. Using compressed air, blow any debris from around
the spark plug(s).

! WARNING
Always wear safety glasses when using compressed
air.

3. Remove the spark plug(s); then attach the high tension lead(s) to the plug(s) and ground the plug(s) on
the cylinder head(s) well away from the spark plug
hole(s).
4. Attach the Compression Tester Kit.
NOTE: The engine should be warm (operating temperature) and the battery fully charged for an accurate compression test. Throttle must be in the
wide-open throttle (WOT) position. In the event the
engine cannot be run, cold values are included.

www.mymowerparts.com

ATV-0051

CAUTION
Before removing a spark plug, be sure to clean the area
around the spark plug. Dirt could enter engine when
removing or installing the spark plug.

Adjust the gap to correct specification (see Section 1 for
proper type and gap). Use a feeler gauge to check the gap.

2-5

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

ATV0052

When installing the spark plug, be sure to tighten it
securely. A new spark plug should be tightened 1/2 turn
once the washer contacts the cylinder head. A used spark
plug should be tightened 1/8 - 1/4 turn once the washer
contacts the cylinder head.

Muffler/Spark Arrester

CF104

Engine/Transmission
Oil - Filter - Strainer
OIL - FILTER
The engine should always be warm when the oil is
changed so the oil will drain easily and completely.

At the intervals shown in the Periodic Maintenance
Chart, clean the spark arrester using the following procedure.

1. Park the ATV on level ground.
2. Remove the oil level stick/filler plug.

! WARNING
Wait until the muffler cools to avoid burns.

1. Remove the three cap screws securing the spark
arrester assembly to the muffler; then loosen and
remove the arrester.

KC372A

1000

CF105A

2. Using a suitable brush, clean the carbon deposits
from the screen taking care not to damage the screen.
NOTE: If the screen or gasket is damaged in any
way, it must be replaced.

3. Install the spark arrester assembly with gasket; then
secure with the three cap screws. Tighten to 48 in.-lb.
GZ415A

3. Remove the drain plug from the bottom of the engine
and drain the oil into a drain pan.

2-6

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

733-441A

GZ461A

4. Remove the oil filter plug from the filter mounting
boss (located on the front side of the transmission
case) and allow the filter to drain completely. Install
the plug and tighten securely.

Do not over-fill the engine with oil. Always make sure
that the oil level is not above the upper mark.

5. Using the adjustable Oil Filter Wrench and a suitable
wrench, remove the old oil filter.

13. Inspect the area around the drain plug and oil filter
for leaks.

NOTE: Clean up any excess oil after removing the
filter.

6. Apply oil to a new filter O-ring and check to make
sure it is positioned correctly; then install the new oil
filter. Tighten securely.
NOTE: Install a new O-ring each time the filter is
replaced.

7. Install the engine drain plug and tighten to 16 ft-lb.
Pour the specified amount of the recommended oil in
the filler hole. Install the oil level stick/filler plug.

8. Start the engine (while the ATV is outside on level
ground) and allow it to idle for a few minutes.

CAUTION

Liquid Cooling System
NOTE: Debris in front of the engine or packed
between the cooling fins of the radiator can reduce
cooling capability. Using a garden hose, wash the
radiator to remove any debris preventing air flow.

CAUTION
Arctic Cat does not recommend using a pressure
washer to clean the radiator core. The pressure may
bend or flatten the fins causing restricted air flow, and
electrical components on the radiator could be damaged. Use only a garden hose with spray nozzle at normal tap pressure.

The cooling system capacity can be found in Section 1.
The cooling system should be inspected daily for leakage
and damage. If leakage or damage is detected, take the
ATV to an authorized Arctic Cat ATV dealer for service.
Also, the coolant level should be checked periodically.

9. Turn the engine off and wait approximately one minute.

CAUTION

10. Remove the oil level stick and wipe it with a clean
cloth.

Continued operation of the ATV with high engine temperature may result in engine damage or premature
wear.

11. Install the oil level stick and thread into the engine
case.
12. Remove the oil level stick; the oil level must be
within the operating range but not exceeding the
upper mark.

www.mymowerparts.com

NOTE: High engine RPM, low vehicle speed, or
heavy load can raise engine temperature. Decreasing
engine RPM, reducing load, and selecting an appropriate transmission gear can lower the temperature.

When filling the cooling system, use a coolant/water
mixture which will satisfy the coldest anticipated weather
conditions of the area in accordance with the coolant
manufacturer’s recommendations. While the cooling system is being filled, air pockets may develop; therefore,
run the engine for five minutes after the initial fill, shut
the engine off, and then fill the cooling system to the bottom of the stand pipe in the radiator neck.
2-7

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Checking/Filling
1. On the 1000 models, remove the two screws from
the front of the radiator access panel. On the 450
models, remove the four screws securing the radiator
access panel.
1000

MP007A

5. Separate the front of the snorkel housing from the
rear; then remove the snorkel housing.

FI465A

450

MP003

6. Remove two reinstallable rivets and remove the
splash guard. The radiator cap can now be accessed
in front of the snorkels.
FI476

2. On the 1000 models, lift the front of the access
panel; then slide the panel forward to disengage the
two rear tabs.

7. Carefully rotate the radiator cap counterclockwise to
release pressure; then remove the cap.

3. On the 1000 models, move the panel rearward until
free of the rack. On the 450 models, move the panel
forward until free of the ATV.
NOTE: Steps 4-6 are for Mud Pro models; for other
models, proceed to step 7.

4. Remove four cap screws securing the snorkel housing to the front inspection panel; then remove two
cap screws from the rear of the snorkel housing.

CF142A

8. Add coolant as necessary; then install the radiator
cap and access panel or snorkel housing.
NOTE: Use a good quality, biodegradable glycol-based, automotive-type antifreeze.

! WARNING
Never check the coolant level when the engine is hot or
the cooling system is under pressure.

CAUTION
MP006A

2-8

www.mymowerparts.com

After operating the ATV for the initial 5-10 minutes, stop
the engine, allow the engine to cool down, and check
the coolant level. Add coolant as necessary.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Front Differential/Rear
Drive Lubricant
NOTE: On the 1000 models, the rear drive incorporates a shock-limiting clutch pack in the gear case
input assembly that is designed to cushion driveline
shock.

CAUTION
Any lubricant used in place of the recommended gear
case lubricant could result in premature failure of the
shock limiter. Do not use any lubricant containing
graphite or molybdenum additives or other friction-modified lubricants as these may cause severe
damage to shock limiter components.

When changing the lubricant, use approved SAE 80W-90
hypoid gear lube.
To check lubricant, remove the fill plug; the lubricant
level should be 1 in. below the threads of the plug. If low,
add SAE approved 80W-90 hypoid gear lubricant as necessary.
To change the lubricant, use the following procedure.
1. Place the ATV on level ground.
2. Remove each fill plug.

737-651B

4. After all the lubricant has been drained, install the
drain plugs and tighten to 45 in.-lb.
5. Pour the appropriate amount of approved SAE
80W-90 hypoid gear lubricant into the filler hole.
NOTE: If the differential/rear drive lubricant is contaminated with water, inspect the drain plug, fill plug,
and/or bladder.

6. Install the fill plugs; then tighten to 16 ft-lb.

CAUTION
Water entering the outer end of the axle will not be able
to enter the rear drive unless the seals are damaged.

Nuts/Bolts/Cap Screws
Tighten all nuts, bolts, and cap screws. Make sure rivets
holding components together are tight. Replace all loose rivets. Care must be taken that all calibrated nuts, bolts, and cap
screws are tightened to specifications (see Section 1).

Headlights/Taillight-Brakelight
AL677C

3. Drain the lubricant into a drain pan by removing in
turn the drain plug from each.

NOTE: The bulb portion of a headlight is fragile.
HANDLE WITH CARE. When replacing a headlight
bulb, do not touch the glass portion of the bulb. If the
glass is touched, it must be cleaned with a dry cloth
before installing. Skin oil residue on the bulb will
shorten the life of the bulb.

! WARNING
Do not attempt to remove a bulb when it is hot. Severe
burns may result.

To replace a headlight bulb, use the following procedure.
1. Rotate the bulb assembly counterclockwise and
remove from the headlight housing; then disconnect
from the wiring harness.
ATV0082A

www.mymowerparts.com

2-9

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
2. Connect the new bulb assembly to the wiring harness
connector; then insert into the headlight housing and
rotate fully clockwise.
To replace the taillight-brakelight bulb, use the following
procedure.
1. Turn the bulb socket assembly counterclockwise and
remove from the housing.

ATV-0070C

NOTE: There should be an average operating load
on the ATV when adjusting the headlight aim.

2. Measure the distance from the floor to the mid-point
of each headlight.
3. Using the measurements obtained in step 2, make
horizontal marks on the aiming surface.
CF135A

2. Pull the bulb straight out of the socket; then insert a
new bulb.

4. Make vertical marks which intersect the horizontal
marks on the aiming surface directly in front of the
headlights.
5. Switch on the lights. Make sure the HIGH beam is
on. DO NOT USE LOW BEAM.
6. Observe each headlight beam aim. Proper aim is
when the most intense beam is centered on the vertical mark 5 cm (2 in.) below the horizontal mark on
the aiming surface.
7. Adjust each headlight by turning the adjuster knob
clockwise to raise the beam or counterclockwise to
lower the beam.

CF132A

3. Insert the bulb socket assembly into the housing and
turn it clockwise to secure.
CHECKING/ADJUSTING HEADLIGHT
AIM
The headlights can be adjusted vertically and horizontally. The geometric center of the HIGH beam light zone
is to be used for vertical and horizontal aiming.
1. Position the ATV on a level floor so the headlights
are approximately 6.1 m (20 ft) from an aiming surface (wall or similar aiming surface).

2-10

www.mymowerparts.com

CD714A

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: An E (Error) in the gear position icon indicates no signal or a poor ground wire connection in
the circuit. Troubleshoot the harness connectors,
gear position switch connector, gear position switch,
and LCD connector.

Shift Lever
CHECKING ADJUSTMENT

Hydraulic Brake Systems
CHECKING/BLEEDING
The hydraulic brake systems have been filled and bled at
the factory. To check and/or bleed a hydraulic brake system, use the following procedure.

CF130B

Stop the ATV completely and shift the transmission into
the R position. The reverse gear indicator light should be
illuminated.

1. With the master cylinder in a level position, check
the fluid level in the reservoir. On the hand brake if
the level in the reservoir is adequate, the sight glass
will appear dark. If the level is low, the sight glass
will appear clear. On the auxiliary brake, the level
must be between the MIN and MAX lines on the reservoir.

! WARNING
Never shift the ATV into reverse gear when the ATV is
moving as it could cause the ATV to stop suddenly
throwing the operator from the ATV.

If the reverse light does not illuminate when shifted to
the reverse position, the switch may be faulty, the fuse
may be blown, the bulb may be faulty, a connection may
be loose or corroded, or the lever may need adjusting. To
adjust, proceed to Adjusting Shift Lever.
ADJUSTING SHIFT LEVER
1. Remove the seat; then remove the left-side engine
cover.

738-420A

2. With the ignition switch in the ON position, loosen
jam nut (A) (left-hand threads); then loosen jam nut
(C) and with the shift lever in the reverse position,
adjust the coupler (B) until the transmission is in
reverse and the (R) icon appears on the LCD.

AL681

2. Compress the brake lever/pedal several times to
check for a firm brake. If the brake is not firm, the
system must be bled.
3. To bleed the main brake system, use the following
procedure.
CF258A

3. Tighten the jam nuts securely; then shift the transmission to each position and verify correct adjustment.
4. Install the left-side engine cover and seat making
sure the seat locks securely in place.

www.mymowerparts.com

A. Remove the cover and fill the reservoir with DOT
4 Brake Fluid; then install and secure the cover.
B. Slowly compress the brake lever several times.

2-11

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
C. Remove the protective cap, install one end of a
clear hose onto one FRONT bleeder screw, and
direct the other end into a container; then while
holding slight pressure on the brake lever, open
the bleeder screw and watch for air bubbles. Close
the bleeder screw before releasing the brake lever.
Repeat this procedure until no air bubbles are
present.

AF637D

PR377C

NOTE: During the bleeding procedure, watch the
reservoir very closely to make sure there is always a
sufficient amount of brake fluid. If low, refill the reservoir before the bleeding procedure is continued. Failure to maintain a sufficient amount of fluid in the
reservoir will result in air in the system.
PR377C

NOTE: During the bleeding procedure, watch the
sight glass very closely to make sure there is always
a sufficient amount of brake fluid. If low, refill the reservoir before the bleeding procedure is continued.
Failure to maintain a sufficient amount of fluid in the
reservoir will result in air in the system.

D. At this point, perform step B and C on the other
FRONT bleeder screw; then move to the REAR
bleeder screw and follow the same procedure.
E. Repeat step D until the brake lever is firm.
4. To bleed the auxiliary brake system, use the following procedure.
A. Remove the cover and fill the reservoir with DOT
4 Brake Fluid; then install and secure the cover.
B. Slowly compress the brake pedal several times.
C. Remove the protective cap, install one end of a
clear hose onto the rear bleeder screw, and direct
the other end into a container; then while holding
slight pressure on the brake pedal, open the
bleeder screw and watch for air bubbles. Close the
bleeder screw before releasing the brake pedal.
Repeat this procedure until no air bubbles are
present.
2-12

www.mymowerparts.com

D. Repeat step B and C until the brake pedal is firm.
5. Carefully check the entire hydraulic brake system
that all hose connections are tight, the bleed screws
are tight, the protective caps are installed, and no
leakage is present.

CAUTION
This hydraulic brake system is designed to use DOT 4
brake fluid only. If brake fluid must be added, care must
be taken as brake fluid is very corrosive to painted surfaces.

INSPECTING HOSES
Carefully inspect the hydraulic brake hoses for cracks or
other damage. If found, the brake hoses must be replaced.
CHECKING/REPLACING PADS
The clearance between the brake pads and brake discs is
adjusted automatically as the brake pads wear. The only
maintenance that is required is replacement of the brake
pads when they show excessive wear. Check the thickness of each of the brake pads as follows.
NOTE: As brake pads wear, it may be necessary to
“top-off” the brake fluid in the reservoir.

1. Remove a front wheel.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
2. Measure the thickness of each brake pad.
3. If thickness of either brake pad is less than 1.0 mm
(0.039 in.), the brake pads must be replaced.

5. Burnish the brake pads (see Burnishing Brake Pads
in this section).

Burnishing Brake Pads
Brake pads (both hydraulic and auxiliary) must be burnished to achieve full braking effectiveness. Braking distance will be extended until brake pads are properly
burnished. To properly burnish the brake pads, use the
following procedure.

! WARNING

PR376B

Failure to properly burnish the brake pads could lead to
premature brake pad wear or brake loss. Brake loss can
result in severe injury.

NOTE: The brake pads should be replaced as a set.

1. Choose an area large enough to safely accelerate the
ATV to 30 mph and to brake to a stop.

4. To replace the brake pads, use the following procedure.
A. Remove the wheel.

2. Accelerate to 30 mph; then compress brake lever or
apply the auxiliary brake to decelerate to 0-5 mph.

B. Remove the cap screws securing the caliper
holder to the knuckle; then remove the pads.

3. Repeat procedure on each brake system twenty
times.
4. Verify that the brakelight illuminates when the hand
lever is compressed or the brake pedal is depressed.

Checking/Replacing
V-Belt
REMOVING
1. Remove the right-side footrest (see Section 8).
PR237

C. Install the new brake pads.
D. Secure the caliper to the knuckle and/or axle
housing with new “patch-lock” cap screws.
Tighten to 20 ft-lb.

2. Remove the cap screws securing the V-belt cover
noting the location of the different-lengthed cap
screws for installing purposes; then using a rubber
mallet, gently tap on the cover tabs to loosen the
cover. Remove the cover.

CD078
PR377B

E. Install the wheel. Tighten to 40 ft-lb (steel
wheels) or 80 ft-lb (aluminum wheels).

www.mymowerparts.com

3. Remove the nut securing the movable drive face;
then remove the face. Account for the flat washer
and spacer.

2-13

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: Keep the drive face plate in contact with the
drive face when removing or installing the drive face
to prevent the rollers from falling out.

GZ085

INSTALLING
CD963

1. Place the V-belt into position on the driven pulley
and over the front shaft.

CD966A

4. Install one of the CVT cover cap screws into the
driven pulley fixed face; then turn the cap screw
clockwise to spread the pulley faces. Remove the
V-belt.

GZ085

NOTE: The arrows on the V-belt should point in
direction of engine rotation (forward).

2. Pinch the V-belt together near its center and slide the
spacer and movable drive face onto the driveshaft.
Secure the drive face with a washer and nut (coated
with red Loctite #271). Tighten the nut to 147 ft-lb
(450 models) or 165 ft-lb (1000 models).

CAUTION
Make sure the movable drive face plate is fully engaged
onto the splines of the clutch shaft before tightening the
nut or false torque readings may occur. This will cause
the assembly to loosen damaging the shaft and clutch
face plate.
GZ076

GZ485A

2-14

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: At this point, the push-bolt can be removed.

3. Rotate the V-belt and clutches until the V-belt is
flush with the top of the driven clutch.
4. Place the V-belt cover gasket into position; then
install the cover and secure with the cap screws making sure the different-lengthed cap screws are in their
proper location. Tighten the cap screws to 8 ft-lb.

CD083

5. Install the right-side footrest (see Section 8).
6. Secure the front fender to the footrest with the two
cap screws. Tighten securely.

www.mymowerparts.com

2-15

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

SECTION 3 - ENGINE/TRANSMISSION

TABLE OF
CONTENTS
Engine/Transmission ............................................... 3-2
Specifications (450)................................................. 3-3
Specifications (1000)............................................... 3-3
Troubleshooting ....................................................... 3-4
Table of Contents (450) ........................................... 3-6
Table of Contents (1000) ....................................... 3-49

www.mymowerparts.com

3-1

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
SPECIAL TOOLS

Engine/Transmission
This section has been organized into sub-sections which
show a progression for the complete servicing of the Arctic Cat ATV engine/transmission.
To service the center crankcase halves, the engine/transmission must be removed from the frame.
To service top-side, left-side, and right-side components,
the engine/transmission does not have to be removed
from the frame.
NOTE: Arctic Cat recommends the use of new gaskets, lock nuts, and seals and lubricating all internal
components when servicing the engine/ transmission.
NOTE: Some photographs and illustrations used in
this section are used for clarity purposes only and
are not designed to depict actual conditions.
NOTE: Critical torque specifications are located in
Section 1.

3-2

www.mymowerparts.com

A number of special tools must be available to the technician when performing service procedures in this section.
Refer to the current Special Tools Catalog for the appropriate tool description.
Description

p/n

Clutch Sleeve Hub Holder

0444-007

Connecting Rod Holder

0444-006

Crankcase Separator/Crankshaft Remover

0444-152

Driven Pulley Compressor

0444-121

Driven Pulley Compressor

0444-140

Magneto Rotor Remover Set

0444-254

Oil Filter Wrench

0644-389

Piston Pin Puller

0644-328

Seal Protector Tool

0444-852

Spanner Wrench

0444-153

Surface Plate

0644-016

Valve Clearance Adjuster

0444-255

V Blocks

0644-535

NOTE: Special tools are available from the Arctic
Cat Service Department.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Specifications (450)
VALVES AND GUIDES
Valve Face Diameter (max)
Valve/Tappet Clearance (cold engine)
Valve Guide/Stem Clearance (max)
Valve Guide Inside Diameter
Valve Stem Outside Diameter
Valve Stem Runout
Valve Margin (min)
Valve Face/Seat Width
Valve Seat Angle
Valve Face Radial Runout
Valve Spring Free Length
Valve Spring Tension @ 32.5 mm

(intake) 35.0 mm
(exhaust) 30.5 mm
(intake) 0.08-0.12 mm
(exhaust) 0.15-0.20 mm

(intake) 0.1 mm
(exhaust) 0.3 mm
5.000-5.012 mm
(intake) 4.975-4.990 mm
(exhaust) 4.955-4.970 mm
(max) 0.10 mm
(intake) 1.1 mm
(min) 0.99 mm
45° +30’
(max) 0.15 mm
(min) 44.73 mm
(outer) 17.23 kg (37.98 lb)

CAMSHAFT AND CYLINDER HEAD
Cam Lobe Height (min)

(intake)
(exhaust)
Camshaft Journal/Cylinder Head Clearance(max)
(right & center)
Camshaft Journal Holder
Inside Diameter
(left)
Camshaft Journal Outside Diameter
(left)
(right & center)
Camshaft Runout
(max)
Rocker Arm Inside Diameter
Rocker Arm Shaft Outside Diameter
Cylinder Head/Cover Distortion
(max)

34.71 mm
34.48 mm
0.074 mm
22.01-22.04 mm
17.51-17.54 mm
17.466-17.480 mm
21.966- 21.980 mm
0.03 mm
10.00-10.15 mm
9.972-9.987 mm
0.05 mm

CYLINDER, PISTON, AND RINGS
Piston Skirt/Cylinder Clearance
Piston Diameter 8 mm from Skirt End
Cylinder Bore
Piston Ring Free End Gap (min)

0.025-0.055 mm
88.96-88.98 mm
89.005-89.015 mm
(1st) 8.0 mm
(2nd) 8.3 mm
Bore x Stroke
89.0 x 71.2 mm
Cylinder Trueness
(max) 0.01 mm
Piston Ring End Gap - Installed
(min) 0.3 8 mm
Piston Ring to Groove Clearance (max) (1st/2nd) 0.06 mm
Piston Ring Groove Width
(1st) 1.01-1.03 mm
(2nd) 1.21-1.23 mm
(oil) 2.01-2.03 mm
Piston Ring Thickness
(1st) 0.97-0.99 mm
(2nd) 1.17-1.19 mm
Piston Pin Bore
(max) 20.008 mm
Piston Pin
(min) 19.994 mm

CRANKSHAFT
Connecting Rod (small end inside diameter)(max)
Connecting Rod (big end side-to-side)
Connecting Rod (small end deflection)
(max)
Crankshaft (web-to-web)
Crankshaft Runout
(max)

20.021 mm
0.7 mm
3.0 mm
60.8-60.9 mm
0.03 mm

Specifications subject to change without notice.

Specifications (1000)
VALVES AND GUIDES
(intake) 31.6 mm
(exhaust) 27.9 mm
Valve/Tappet Clearance (cold engine)
(intake) 0.08-0.12 mm
(exhaust) 0.13-0.17 mm
Valve Guide/Stem Clearance
(max) 0.013 mm
Valve Guide/Valve Stem Deflection
(max) 0.35 mm
(wobble method)
Valve Guide Inside Diameter
5.000-5.012 mm
Valve Stem Outside Diameter
4.972-4.987 mm
Valve Stem Runout
(max) 0.1 mm
Valve Head Thickness
(min) 2.3 mm
Valve Face/Seat Width (max)
(intake) 2.25 mm
(exhaust) 2.60 mm
Valve Seat Angle
45° +15’/+30’
Valve Face Radial Runout
(max) 0.2 mm
Valve Spring Free Length
(min) 38.7 mm
Valve Spring Tension @ 31.5 mm
19.0 kg (42 lb)
CAMSHAFT AND CYLINDER HEAD
Cam Lobe Height
(min) 33.53 mm
Camshaft Journal/Cylinder
(max) 0.04 mm
Head Clearance
Camshaft Journal Holder
(right & center) 21.98-22.04 mm
Inside Diameter
(left) 17.48-17.53 mm
Camshaft Journal Outside
(right & center) 21.96-21.98 mm
Diameter
(left) 17.47-17.48 mm
Camshaft Runout
(max) 0.05 mm
Rocker Arm Inside Diameter
12.000-12.018 mm
Rocker Arm Shaft Outside Diameter
11.97-11.98 mm
Cylinder Head/Cover Distortion
(max) 0.05 mm
CYLINDER, PISTON, AND RINGS
Piston Skirt/Cylinder Clearance
(max) 0.05 mm
Cylinder Bore
91.992-92.008 mm
Piston Diameter 15 mm from Skirt End
91.949-91.959 mm
Piston Ring End Gap (min)
(1st/2nd) 12.5 mm
Bore x Stroke
92 x 71.5 mm
Cylinder Trueness
(max) 0.075 mm
Piston Ring End Gap - Installed (max)
0.38 mm
Piston Ring to Groove Clearance (max)
(1st) 0.034 mm
(2nd) 0.033 mm
Piston Ring Groove Width
(1st/2nd) 1.202-1.204 mm
(oil) 2.501-2.503 mm
Piston Ring Thickness
(1st/2nd) 1.170-1.195 mm
Piston Pin Bore
(max) 20.012 mm
Piston Pin Outside Diameter
(min) 19.995 mm
CRANKSHAFT
Connecting Rod
(max) 20.021 mm
(small end inside diameter)
Connecting Rod (big end side-to-side)
(max) 0.95 mm
Connecting Rod @ 150 mm
(max) 0.3 mm
(small end deflection)
Crankshaft (web-to-web)
(max) 98 mm
Crankshaft Runout
(max) 0.03 mm
Oil Pump Gerotor Clearance
(max) 0.15 mm
Valve Face Diameter (max)

Specifications subject to change without notice.

www.mymowerparts.com

3-3

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Troubleshooting
Problem: Engine will not start or is hard to start (Compression too low)
Condition
Remedy
1.
2.
3.
4.
5.
6.

Valve clearance out of adjustment
Valve guides worn
Valve timing incorrect
Piston rings worn excessively
Cylinder bore worn
Starter motor cranks too slowly - does not turn

1.
2.
3.
4.
5.
6.

Adjust clearance
Repair - replace guides
Replace cam chain/sprocket and retime engine
Replace rings
Replace cylinder
See Section 5 - Troubleshooting

Problem: Engine will not start or is hard to start (No spark)
Condition
Remedy
1.
2.
3.
4.
5.
6.

Spark plug fouled
Spark plug wet
Magneto defective
ECU defective
Ignition coil defective
High-tension lead open - shorted

1.
2.
3.
4.
5.
6.

Clean - replace plug
Clean - dry plug
Replace stator coil
Replace ECU
Replace ignition coil
Replace high tension lead

Problem: Engine will not start or is hard to start (No fuel reaching the fuel injector)
Condition
Remedy
1.
2.
3.
4.

Gas tank vent hose obstructed
Fuel hose obstructed
Fuel screens obstructed
Fuel pump defective

Problem: Engine stalls easily
Condition
1.
2.
3.
4.
5.

Spark plug fouled
Magneto defective
ECU defective
Fuel injector obstructed
Valve clearance out of adjustment

Problem: Engine noisy (Excessive valve chatter)
Condition
1.
2.
3.
4.
5.

Valve clearance too large
Valve spring(s) weak - broken
Rocker arm - rocker arm shaft worn
Camshaft worn
Valve tappets worn

1.
2.
3.
4.

Clean vent hose
Clean - replace hose
Clean - replace inlet screen - valve screen
Replace fuel pump

Remedy
1.
2.
3.
4.
5.

Clean plug
Replace magneto
Replace ECU
Replace fuel injector
Adjust clearance

Remedy
1.
2.
3.
4.
5.

Adjust clearance
Replace spring(s)
Replace arm - shaft
Replace camshaft
Replace tappets

Problem: Engine noisy (Noise seems to come from piston)
Condition
Remedy
1.
2.
3.
4.

Piston - cylinder worn
Combustion chamber carbon buildup
Piston pin - piston pin bore worn
Piston rings - ring groove(s) worn

1.
2.
3.
4.

Replace - service piston - cylinder
Clean cylinder head and piston
Replace - service pin - bore
Replace rings - piston

Problem: Engine noisy (Noise seems to come from timing chain)
Condition
Remedy
1. Chain stretched
2. Sprockets worn
3. Tension adjuster malfunctioning

1. Replace chain
2. Replace sprockets
3. Repair - replace adjuster

Problem: Engine noisy (Noise seems to come from crankshaft)
Condition
Remedy
1. Main bearing worn - burned
2. Lower rod-end bearing worn - burned
3. Connecting rod side clearance too large

1. Replace bearing
2. Replace crankshaft assembly
3. Replace crankshaft assembly

Problem: Engine noisy (Noise seems to come from transmission)
Condition
Remedy
1.
2.
3.
4.
5.

3-4

Gears worn
Splines worn
Primary gears worn
Bearings worn
Bushing worn

www.mymowerparts.com

1.
2.
3.
4.
5.

Replace gears
Replace shaft(s)
Replace gears
Replace bearings
Replace bushing

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Problem: Engine noisy (Noise seems to come from secondary bevel gear and final driven shaft)
Condition
Remedy
1.
2.
3.
4.
5.
6.

Drive - driven bevel gears damaged - worn
Backlash incorrect
Tooth contact improper
Bearing damaged
Gears worn
Splines worn

Problem: Engine idles poorly
Condition
1.
2.
3.
4.
5.
6.
7.
8.
9.

Valve clearance incorrect
Valve seating poor
Valve guides defective
Rocker arms - arm shaft worn
Magneto defective
ECU defective
Spark plug fouled - gap incorrect
Ignition coil defective
Fuel injector obstructed

Problem: Engine runs poorly at high speed
Condition
1.
2.
3.
4.
5.
6.
7.
8.
9.

High RPM “cut out” against RPM limiter
Valve springs weak
Valve timing incorrect
Cams - rocker arms - tappets worn
Spark plug gap incorrect
Ignition coil defective
Fuel pump defective
Air cleaner element obstructed
Fuel hose obstructed

Problem: Exhaust smoke dirty or heavy
Condition
1.
2.
3.
4.
5.
6.

Engine oil overfilled - contaminated
Piston rings - cylinder worn
Valve guides worn
Cylinder wall scored
Valve stems worn
Stem seals defective

1.
2.
3.
4.
5.
6.

Replace gears
Adjust backlash
Adjust contact
Replace bearing
Replace gears
Replace shaft(s)

Remedy
1.
2.
3.
4.
5.
6.
7.
8.
9.

Adjust clearance
Replace - service seats - valves
Replace guides
Replace arms - shafts
Replace stator coil
Replace ECU
Adjust gap - replace plug
Replace ignition coil
Replace fuel injector

Remedy
1.
2.
3.
4.
5.
6.
7.
8.
9.

Shift into higher gear - decrease speed
Replace springs
Time valves
Replace cams - arms - tappets
Adjust gap
Replace ignition oil
Replace fuel pump
Clean element
Clean or replace hose

Remedy
1.
2.
3.
4.
5.
6.

Drain excess oil - replace oil
Replace - service rings - cylinder
Replace guides
Replace - service cylinder
Replace valves
Replace seals

Problem: Engine lacks power
Condition

Remedy

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.

Valve clearance incorrect
Valve springs weak
Valve timing incorrect
Piston ring(s) - cylinder worn
Valve seating poor
Spark plug fouled
Rocker arms - shafts worn
Spark plug gap incorrect
Fuel injector obstructed
Cam chain worn
Air cleaner element obstructed
Engine oil overfilled - contaminated
Intake manifold leaking air

Adjust clearance
Replace springs
Re-time valve gear
Replace - service rings - cylinder
Repair seats
Clean - replace plug
Replace arms - shafts
Adjust gap - replace plug
Replace injector
Replace cam chain
Clean element
Drain excess oil - change oil
Tighten - replace manifold

Problem: Engine overheats
Condition

Remedy

1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.

Carbon deposit (piston crown) excessive
Oil low
Octane low - gasoline poor
Oil pump defective
Oil circuit obstructed
Radiator hoses - cap damaged - obstructed
Intake manifold leaking air
Coolant level low
Fan malfunctioning
Fan relay malfunctioning
Thermostat stuck - closed

www.mymowerparts.com

Clean piston
Add oil
Drain - replace gasoline
Replace pump
Clean circuit
Clear obstruction - replace hoses
Tighten - replace manifold
Fill - examine system for leaks
Check fan fuse - replace fan
Replace fan relay
Replace thermostat

3-5

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Table of Contents
(450)
Removing Engine/ Transmission............................. 3-6
Top-Side Components............................................. 3-8
Removing Top-Side Components ........................... 3-8
Servicing Top-Side Components........................... 3-11
Installing Top-Side Components ........................... 3-19
Left-Side Components .......................................... 3-22
Removing Left-Side Components ......................... 3-22
Servicing Left-Side Components .......................... 3-25
Installing Left-Side Components ........................... 3-27
Right-Side Components ........................................ 3-29
Removing Right-Side Components....................... 3-29
Servicing Right-Side Components ........................ 3-32
Installing Right-Side Components......................... 3-33
Center Crankcase Components............................ 3-36
Separating Crankcase Halves............................... 3-37
Disassembling Crankcase Half ............................. 3-37
Servicing Center Crankcase Components............ 3-39
Assembling Crankcase Half .................................. 3-44
Joining Crankcase Halves..................................... 3-46
Installing Engine/Transmission.............................. 3-47

2. Remove the left footwell, footrest, and footwell
support assembly; then drain the coolant into a
suitable container.

FI530A

3. From the left side, remove the gear position switch
connector (A) and the speed sensor connector (B).

Removing Engine/
Transmission
FI525A

Many service procedures can be performed without
removing the engine/transmission from the frame.
Closely observe the note introducing each sub-section
for this important information.

4. Drain the engine oil into a suitable container.
5. Remove the storage compartment; then remove
the air inlet tube from air filter housing and throttle
body.

AT THIS POINT
If the technician’s objective is to service Top-Side Components, Left-Side Components, or Right-Side Components, the engine/transmission does not have to be
removed from the frame.

AT THIS POINT
If the technician’s objective is to service/replace magneto cover oil seals or the oil strainer (from beneath the
engine/transmission), the engine/transmission does not
have to be removed from the frame.

Secure the ATV on a support stand to elevate the
wheels.
! WARNING
Make sure the ATV is solidly supported on the support
stand to avoid injury.

1. Remove the seat and tool tray; then disconnect the
negative battery cable.

3-6

www.mymowerparts.com

FI516A

6. Remove the air inlet and outlet ducts from the
CVT housing.
7. Loosen the clamp securing the air filter housing to
the front air inlet duct; then disconnect the coil
connector and remove the spark plug cap from the
spark plug.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

FI519A

FI533A

8. Disconnect the crankcase breather hose from the
air filter housing and remove the air filter assembly.

11. Remove the screws securing throttle arm cover to
the throttle body; then loosen the throttle cable
jam-nut and remove the throttle cable.

9. From the top side, remove the engine coolant temperature (ECT) sensor connector (C), fuel injector
connector (D), manifold absolute pressure/inlet air
temperature (MAP/IAT) sensor connector (E), idle
step control (ISC) connector (F), and throttle position sensor (TPS) connector (G).

FI536A

12. Remove the cap screws securing the exhaust pipe
to the cylinder head; then remove the springs
securing the muffler to the exhaust pipe.
13. Remove the muffler and exhaust pipe. Account for
a grafoil seal on each end of the exhaust pipe.
FI522A

10. From the right side, disconnect the stator connector (H) and crankshaft position sensor connector
(I) from the main harness; then disconnect the positive cable from the starter motor and the engine
ground cable from the starter mounting flange.

14. Remove coolant hoses (A) and (B) from the water
pump; then remove the upper coolant hose from
the thermostat housing.

FI530B

FI523A

www.mymowerparts.com

3-7

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
1. Remove the cap screws securing the two tappet
covers. Remove the two tappet covers. Account
for the O-rings.

FI537

15. Remove the four cap screws securing the rear
driveline to the output drive flange.
16. Support the engine and remove the two
through-bolts securing the engine assembly to the
frame; then move the engine rearward sufficiently
to disengage the front driveline and remove the
engine from the left side.

Top-Side Components

FI603

NOTE: Keep the mounting hardware with the covers for assembly purposes.

2. Remove the cylinder head cover cap screws. Note
the rubber washers on the four top-side cap
screws; remove the cylinder head cover. Note the
orientation of the cylinder head plug and remove
it. Note the location of the two alignment pins.

NOTE: For efficiency, it is preferable to remove
and disassemble only those components which
need to be addressed and to service only those
components. The technician should use discretion
and sound judgment.

AT THIS POINT
To service any one specific component, only limited disassembly of components may be necessary. Note the
AT THIS POINT information in each sub-section.

NOTE: The engine/transmission does not have to
removed from the frame for this procedure.

FI606A

Removing Top-Side
Components
A. Cylinder Head Cover/
Rocker Arms
B. Cylinder Head/Camshaft
NOTE: Remove the spark plug, timing inspection
plug, and outer magneto cover; then using an
appropriate wrench, rotate the crankshaft to
top-dead-center of the compression stroke.
NOTE: Arctic Cat recommends the use of new
gaskets, lock nuts, and seals and lubricating all
internal
components
when
servicing
the
engine/transmission.
3-8

www.mymowerparts.com

MD1354A

3. Remove the cap screw from the tension adjuster;
then using a flat-blade screwdriver, relax the cam
chain tension by rotating the adjuster screw clockwise until it locks.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: Care should be taken not to drop the
C-ring down into the crankcase.

FI607A

MD1131

6. Noting the timing marks for installing purposes,
drop the sprocket off the camshaft. While holding
the cam chain, slide the sprocket and camshaft out
of the cylinder head. Account for an alignment
pin.
NOTE: Loop the chain over the cylinder and
secure it to keep it from falling into the crankcase.

FI608

4. Bend the washer tabs and remove the two cap
screws securing the sprocket to the camshaft.

FI620

FI612

5. Using an awl, rotate the C-ring in its groove until
it is out of the cylinder head; then remove the
C-ring.

FI617A

7. Remove the cam chain tensioner pivot bolt and
remove the chain tensioner; then remove the two
nuts securing the cylinder head to the cylinder.

FI613

www.mymowerparts.com

3-9

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

FI616

CD211

9. Remove the cylinder head from the cylinder,
remove the gasket, and account for two alignment
pins.

FI617

FI623A

AT THIS POINT
To service valves and cylinder head, see Servicing
Top-Side Components sub-section.

10. Remove the cam chain guide.

AT THIS POINT
FI618A

To inspect cam chain guide, see Servicing Top-Side
Components sub-section.

FI619A

8. Remove the four cylinder head cap screws and
washers. Note that the two cap screws on the right
side of the cylinder head nearest the cam sprocket
are longer than the two cap screws on the left
(spark plug) side.

3-10

www.mymowerparts.com

FI621

C. Cylinder
D. Piston
NOTE: Steps 1-10 in the preceding sub-section
must precede this procedure.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
11. Remove the two nuts securing the right side of the
cylinder to the right-side crankcase half.

NOTE: It is advisable to remove the opposite-side
circlip prior to using the puller.

FI622A

MD1219

12. Lift the cylinder off the crankcase taking care not
to allow the piston to drop against the crankcase.
Account for the gasket and two alignment pins.

NOTE: Support the connecting rod with rubber
bands to avoid damaging the rod or install a connecting rod holder.

CAUTION
Do not allow the connecting rod to go down inside the
crankcase. If the rod is down inside the crankcase and
the crankshaft is rotated, severe damage will result.

AT THIS POINT
To service piston, see Servicing Top-Side Components
sub-section.

AT THIS POINT
To service center crankcase components only, proceed
to Removing Left-Side Components.
FI624A

AT THIS POINT
To service cylinder, see Servicing Top-Side Components sub-section.

CAUTION
When removing the cylinder, be sure to support the piston to prevent damage to the crankcase and piston.

13. Using an awl, remove one piston-pin circlip. Take
care not to drop it into the crankcase.

Servicing Top-Side
Components
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is
necessary.

VALVE ASSEMBLY
When servicing valve assembly, inspect valve seats,
valve stems, valve faces, and valve stem ends for pits,
burn marks, or other signs of abnormal wear.
NOTE: Whenever a valve is out of tolerance, it
must be replaced.

Cleaning/Inspecting Cylinder Head
Cover
FI625

14. Using Piston Pin Puller, remove the piston pin.
Account for the opposite-side circlip. Remove the
piston.

www.mymowerparts.com

NOTE: If the cylinder head cover cannot be trued,
the cylinder head assembly must be replaced.

1. Wash the cylinder head cover in parts-cleaning
solvent.
3-11

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
2. Place the cylinder head cover on the Surface Plate
covered with #400 grit wet-or-dry sandpaper.
Using light pressure, move the cylinder head cover
in a figure eight motion. Inspect the sealing surface for any indication of high spots. A high spot
can be noted by a bright metallic finish. Correct
any high spots before assembly by continuing to
move the cylinder head cover in a figure eight
motion until a uniform bright metallic finish is
attained.

CAUTION
Do not remove an excessive amount of the sealing surface or damage to the camshaft will result. Always
check camshaft clearance when resurfacing the cylinder head cover.

CC134D

CC136D

NOTE: The valve seals must be replaced.
CC130D

CAUTION
Water or parts-cleaning solvent must be used in conjunction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

Removing Valves

3. Remove the valve springs; then invert the cylinder
head and remove the valves.
Measuring Valve Stem Runout
1. Support each valve stem end with the V Blocks;
then check the valve stem runout using a dial indicator.

NOTE: Index all valves, springs, and cotters to
their original position when removing. When
installing, all valve components should be
installed in their original position.

1. Using a valve spring compressor, compress the
valve springs and remove the valve keepers.
Account for an upper spring retainer.

ATV-1082

2. Maximum runout must not exceed specifications.
Measuring Valve Stem Outside
Diameter
1. Using a micrometer, measure the valve stem outside diameter.
CC132D

2. Remove the valve seal and the lower remaining
spring seat. Discard the valve seal.
3-12

www.mymowerparts.com

2. Acceptable diameter ranges must be within specifications.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Measuring Valve Face/Seat Width
1. Using a calipers, measure the width of the valve
face.

Servicing Valves/Valve
Guides/Valve Seats
If valves, valve guides, or valve seats require servicing
or replacement, Arctic Cat recommends that the components be taken to a qualified machine shop for servicing.

CAUTION
If valves are discolored or pitted or if the seating surface is worn, the valve must be replaced. Do not attempt
to grind the valves or severe engine damage may occur.

Measuring Rocker Arm
(Inside Diameter)

FI367

2. Acceptable width must be at or above specifications.
Measuring Valve Face Radial
Runout

1. Using a dial calipers, measure the inside diameter
of the rocker arm.
2. Acceptable inside diameter range must be within
specifications.

Measuring Rocker Arm Shaft
(Outside Diameter)

1. Mount a dial indicator on the surface plate; then
place the valve stem on a set of V blocks.

1. Using a micrometer, measure the outside diameter
of the rocker arm shaft.

2. Position the dial indicator contact point on the outside edge of the valve face; then zero the indicator.

2. Acceptable outside diameter range must be within
specifications.
Installing Valves
1. Apply grease to the inside surface of the valve
seals; then place a lower spring seat and valve
guide seal over each valve guide.

ATV1082A

3. Rotate the valve in the V blocks.
4. Maximum runout must not exceed specifications.
Measuring Valve Guide
(Inside Diameter)
1. Insert a snap gauge 1/2 way down into each valve
guide bore; then remove the gauge and measure it
with a micrometer.
2. Acceptable inside diameter range must be within
specifications.
3. If a valve guide is out of tolerance, the cylinder
head must be replaced.

www.mymowerparts.com

CC144D

2. Insert each valve into its original valve location.
3. Install the valve springs with the painted end of the
spring facing away from the cylinder head.
NOTE: If the paint is not visible, install the ends
of the springs with the closest wound coils toward
the head.

3-13

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

ATV-1011A

CC400D

4. Place a spring retainer over the valve springs; then
using the valve spring compressor, compress the
valve springs and install the valve keepers.

2. Remove each ring by working it toward the top of
the piston while rotating it out of the groove.
NOTE: When installing new rings, install as a
complete set only.

Cleaning/Inspecting Piston Ring
Grooves
1. Take an old piston ring and snap it into two pieces;
then grind the end of the old ring to a 45° angle
and to a sharp edge.
2. Using the sharpened ring as a tool, clean carbon
from the ring grooves. Be sure to position the ring
with its tapered side up.
CC132D

PISTON ASSEMBLY
NOTE: Whenever a piston, rings, or pin are out of
tolerance, they must be replaced.

Cleaning/Inspecting Piston
1. Using a non-metallic carbon removal tool, remove
any carbon buildup from the top of the piston.
2. Inspect the piston for cracks in the piston pin,
boss, top, and skirt areas.
3. Inspect the piston for seizure marks or scuffing. If
piston is scored or galled, replace it with a new
one.

CAUTION
Improper cleaning of the ring grooves by the use of the
wrong type of ring groove cleaner will result in severe
damage to the piston.

Measuring Piston-Ring End Gap
(Installed)
1. Place each piston ring in the wear portion of the
cylinder. Use the piston to position each ring
squarely in the cylinder.
2. Using a feeler gauge, measure each piston-ring
end gap. Acceptable ring end gap must not exceed
specifications.

4. Inspect the perimeter of each piston for signs of
“blowby” indicated by dark discoloration.
“Blowby” is caused by worn piston rings, excessive carbon in ring grooves, or an out-of-round
cylinder.
Removing Piston Rings
1. Starting with the top ring, slide one end of the ring
out of the ring-groove.
CC995

3-14

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Measuring Piston Pin, Connecting
Rod Small End, and Piston-Pin Bore
1. Measure the piston pin outside diameter at each
end and in the center. If measurement does not
meet specifications, the piston pin must be
replaced.

CC127D

2. Measure the corresponding piston diameter at a
point 8 mm (0.3 in.) above the piston skirt at a
right angle to the piston-pin bore. Subtract this
measurement from the measurement in step 1. The
difference (clearance) must be within specifications.
ATV-1070

2. Inspect and measure the connecting rod small end
inside diameter. If the measurement exceeds specifications, the connecting rod must be replaced
(see Center Crankcase Components in this section).
3. Insert an inside dial indicator into the piston-pin
bore. Take two measurements to ensure accuracy.
The diameter must not exceed specifications. If the
diameter exceeds specifications, the piston must
be replaced.

Installing Piston Rings
1. Install ring expander (4) in the bottom groove of
the piston; then install the thin oil rings (3) over
the expander making sure the expander ends do
not overlap. Stagger the end gaps of the upper and
lower thin oil rings according to the illustration.
NOTE: Note the direction of the exhaust side of
the piston (5) for correct ring end gap orientation.

ATV-1085B
ATV-1069

Measuring Piston Skirt/
Cylinder Clearance
1. Measure the cylinder front to back in six places.

www.mymowerparts.com

2. Install the compression rings (1 and 2) so the letter(s) on the top surface of each ring faces the
dome of the piston. Rotate the rings until the ring
end gaps are on directly opposite sides of the piston according to the illustration.
NOTE: The chrome (silver) ring should be
installed in the top position.

3-15

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
2. Lay a straightedge across the cylinder head; then
using a feeler gauge, check the distortion factor
between the head and the straightedge.
3. Maximum distortion must not exceed specifications.

MD1343A

CAUTION
Incorrect installation of the piston rings will result in
engine damage.

CYLINDER/CYLINDER HEAD
ASSEMBLY
NOTE: If the cylinder/cylinder head assembly
cannot be trued, they must be replaced.

Cleaning/Inspecting Cylinder Head

CAUTION
The cylinder head studs must be removed for this procedure.

1. Using a non-metallic carbon removal tool, remove
any carbon buildup from the combustion chamber
being careful not to nick, scrape, or damage the
combustion chamber or the sealing surface.
2. Inspect the spark plug hole for any damaged
threads. Repair damaged threads using a
“heli-coil” insert.
3. Place the cylinder head on the surface plate covered with #400 grit wet-or-dry sandpaper. Using
light pressure, move the cylinder head in a figure
eight motion. Inspect the sealing surface for any
indication of high spots. A high spot can be noted
by a bright metallic finish. Correct any high spots
before assembly by continuing to move the cylinder head in a figure eight motion until a uniform
bright metallic finish is attained.

CC141D

Cleaning/Inspecting Cylinder
1. Wash the cylinder in parts-cleaning solvent.
2. Inspect the cylinder for pitting, scoring, scuffing,
warpage, and corrosion. If marks are found, repair
the surface using a cylinder hone (see Honing Cylinder in this sub-section).
3. Place the cylinder on the surface plate covered
with #400 grit wet-or-dry sandpaper. Using light
pressure, move the cylinder in a figure eight
motion. Inspect the sealing surface for any indication of high spots. A high spot can be noted by a
bright metallic finish. Correct any high spots
before assembly by continuing to move the cylinder in a figure eight motion until a uniform bright
metallic finish is attained.

CAUTION
Water or parts-cleaning solvent must be used in conjunction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

Measuring Cylinder Head
Distortion
1. Remove any carbon buildup in the combustion
chamber.

3-16

www.mymowerparts.com

CC129D

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Inspecting Cam Chain Guide

Measuring Camshaft Runout

1. Inspect cam chain guide for cuts, tears, breaks, or
chips.

NOTE: If the camshaft is out of tolerance, it must
be replaced.

2. If the chain guide is damaged, it must be replaced.

1. Place the camshaft on a set of V blocks; then position the dial indicator contact point against the
shaft and zero the indicator.

Honing Cylinder
1. Using a slide gauge and a dial indicator or a snap
gauge, measure the cylinder bore diameter in three
locations from top to bottom and again from top to
bottom at 90° from the first measurements for a
total of six measurements. The trueness
(out-of-roundness) is the difference between the
highest and lowest reading. Maximum trueness
(out-of-roundness) must not exceed specifications.

CC283D

2. Rotate the camshaft and note runout; maximum
tolerance must not exceed specifications.
Measuring Camshaft Lobe Height
1. Using a calipers, measure each cam lobe height.
CC127D

2. Wash the cylinder in parts-cleaning solvent.
3. Inspect the cylinder for pitting, scoring, scuffing,
and corrosion. If marks are found, repair the surface using a #320 grit ball hone.
NOTE: To produce the proper 60° cross-hatch
pattern, use a low RPM drill (600 RPM) at the rate
of 30 strokes per minute. If honing oil is not available, use a lightweight petroleum-based oil. Thoroughly clean cylinder after honing using soap and
hot water. Dry with compressed air; then immediately apply oil to the cylinder bore. If the bore is
severely damaged or gouged, replace the cylinder.

ATV1013A

2. The lobe heights must be greater than minimum
specifications.
Inspecting Camshaft Bearing
Journal
1. Inspect the bearing journal for scoring, seizure
marks, or pitting.
2. If excessive scoring, seizure marks, or pitting is
found, the cylinder head assembly must be
replaced.
Measuring Camshaft to
Cylinder Head Clearance

CC390D

4. If any measurement exceeds the limit, the cylinder
must be replaced.

www.mymowerparts.com

1. Loosen the jam nuts and adjuster screws.

3-17

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

CC005D

2. Place a strip of plasti-gauge in each of the camshaft lands in the cylinder head.
3. Place the valve cover on the cylinder head and
secure with the valve cover cap screws. Tighten
securely.
NOTE: Do not rotate the camshaft when measuring clearance.

CC287D

NOTE: If the journals are worn, replace the camshaft; then measure the clearance again. If it is still
out of tolerance, replace the cylinder head.

Inspecting Camshaft Spring/Drive
Pin
1. Inspect the spring and unloader pin for damage.

4. Remove the cap screws securing the valve cover to
the cylinder; then remove the valve cover and
camshaft.

CF061A

MD1261

5. Match the width of the plasti-gauge with the chart
found on the plasti-gauge packaging to determine
camshaft to cylinder head and valve cover clearance.

NOTE: With the weight extended, the unloader
pin should be flat-side out; with the weight
retracted, the unloader pin should be round-side
out.

CF060A

2. If damaged, the camshaft must be replaced.
CC145D

6. If clearance is excessive, measure the journals of
the camshaft.

3-18

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
CAUTION

Installing Top-Side
Components

The cylinder should slide on easily. Do not force the cylinder or damage to the piston, rings, cylinder, or crankshaft assembly may occur.

A. Piston
B. Cylinder
1. Lubricate the piston pin, connecting rod, and piston pin bore with motor oil; then install the piston
on the connecting rod making sure there is a circlip on each side.

GZ142

4. Loosely install the two nuts securing the cylinder
to the right-side crankcase half.
NOTE: The two cylinder-to-crankcase nuts will be
tightened in step 9.

FI626

NOTE: The piston should be installed so the IN
points towards the intake side.

2. Place the two alignment pins into position. Place a
new cylinder gasket into position; then place a piston holder (or suitable substitute) beneath the piston skirt and square the piston in respect to the
crankcase.
FI622A

C. Cylinder Head/Camshaft
D. Cylinder Head Cover/
Rocker Arms
NOTE: Steps 1-4 in the preceding sub-section
must precede this procedure.

5. While keeping tension on the cam chain, place the
front cam chain guide into the cylinder.
MD1344

3. Lubricate the inside wall of the cylinder; then
using a ring compressor or the fingers, compress
the rings and slide the cylinder over the piston.
Route the cam chain up through the cylinder cam
chain housing; then remove the piston holder and
seat the cylinder firmly on the crankcase.

www.mymowerparts.com

CAUTION
Care should be taken that the bottom of the chain guide
is secured in the crankcase boss.

3-19

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

FI621

CD383

6. Place a new gasket into position on the cylinder.
Place the alignment pins into position; then place
the head assembly into position on the cylinder
making sure the cam chain is routed through the
chain cavity.

12. With the alignment pin installed in the camshaft
and the cam lobes directed down (toward the piston), place the camshaft in position and verify that
the timing mark on the magneto is visible through
the inspection plug and that the timing marks on
the camshaft sprocket are parallel with the valve
cover mating surface.

CAUTION
Keep tension on the cam chain to avoid damaging the
crankcase boss.

GZ190C

MD1347

7. Install the four cylinder head cap screws with
washers. Note that the two cap screws on the right
side of the cylinder head nearest the cam sprocket
are longer than the two cap screws on the left
(spark plug) side. Tighten only until snug.
8. Install the two lower nuts securing the cylinder
head to the cylinder, one in front and one in rear.

NOTE: When the camshaft assembly is seated,
make sure the alignment pin in the camshaft aligns
with the smallest hole in the sprocket.

13. With the alignment pin installed in the camshaft,
loosely place the cam sprocket (with the recessed
side facing the camshaft lobes) onto the camshaft
and place it into position with the cam chain over
the sprocket.

9. In a crisscross pattern, tighten the four cylinder
head cap screws (from step 7) to 28 ft-lb. Tighten
the two lower cylinder head nuts (from step 8) to
20 ft-lb and the cylinder-to-crankcase nuts (from
step 4) to 8 ft-lb.
10. With the timing inspection plug removed and the
cam chain held tight, rotate the crankshaft until the
piston is at top-dead-center.
11. While holding the cam chain to the front, install
the rear cam chain tensioner guide into the cylinder head. Install the pivot cap screw and washer.
Tighten to 11 ft-lb.

3-20

www.mymowerparts.com

CD463

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
16. Place the tab washer onto the sprocket making
sure it covers the pin in the alignment hole.

MD1359

14. Place the C-ring into position in its groove in the
cylinder head.

MD1363

CAUTION
Care must be taken that the tab washer is installed correctly to cover the alignment hole on the sprocket. If the
alignment pin falls out, severe engine damage will
result.

17. Apply red Loctite #271 to the first cap screw
securing the sprocket and tab washer to the camshaft; then install the cap screw and tab washer.
Tighten cap screw only until snug.

FI615

NOTE: At this point, oil the camshaft bearings,
cam lobes, and the three seating journals on the
cylinder head.
NOTE: Note the position of the alignment marks
on the end of the camshaft. They must be parallel
with the valve cover mating surface. If rotating the
camshaft and sprocket is necessary for alignment,
do not allow the crankshaft to rotate and be sure
the cam lobes end up in the down position.

CC404D

15. When the camshaft assembly is seated, ensure the
following.
A. Piston still at top-dead-center.
B. Camshaft lobes directed down (toward the piston).
C. Camshaft alignment marks parallel to the valve
cover mating surface.
D. Recessed side of the sprocket directed toward
the cam lobes.
E. Camshaft alignment pin and sprocket alignment
hole (smallest) are aligned.

CAUTION
If any of the above factors are not as stated, go back to
step 13 and carefully proceed.

www.mymowerparts.com

FI612

18. Rotate the crankshaft until the second cap screw
securing the sprocket to the camshaft can be
installed; then install the cap screw (threads coated
with red Loctite #271). Tighten to 11 ft-lb; then
bend the tab to secure the cap screw.

3-21

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
19. Rotate the crankshaft until the first cap screw
(from step 17) securing the sprocket to the camshaft can be addressed; then tighten to 11 ft-lb.
Bend the tab to secure the cap screw.
20. Install the cylinder head plug with the cupped end
facing the camshaft and the opening directed
downwards.

27. Adjust valve/tappet clearance (see Section 2).
28. Place the two tappet covers with O-rings into position; then install and tighten the cap screws to 8
ft-lb.

21. Place the cam chain tensioner assembly and gasket
into the cylinder. Tighten to 10 ft-lb.
22. Using a flat-blade screwdriver, turn the tensioner
screw counterclockwise to apply tension to the
cam chain; then install the cap screw plug and
washer and tighten securely.

FI602

29. Install the spark plug and tighten securely; then
install the timing inspection plug.

Left-Side Components

FI608

23. Loosen the adjuster screw jam nuts; then loosen
the adjuster screws on the rocker arms in the valve
cover.
24. Apply a thin coat of Three Bond Sealant to the
mating surface of the valve cover; then place the
valve cover into position. Note that the two alignment pins are properly positioned.
NOTE: At this point, the rocker arms and adjuster
screws must not have pressure on them.

25. Install the four top-side cap screws with rubber
washers; then install the remaining cap screws.
Tighten only until snug.

AT THIS POINT
To service any one specific component, only limited disassembly of components may be necessary. Note the
AT THIS POINT information in each sub-section.

NOTE: The engine/transmission does not have to
be removed from the frame for this procedure.

Removing Left-Side
Components
A. Water Pump
B. Speed Sensor
C. Magneto Cover/
Stator Assembly
1. Remove the coolant hose connecting the water
pump to the cylinder; then remove the water pump
cover.

MD1261

26. In a crisscross pattern starting from the center and
working outward, tighten the cap screws (from
step 25) to 8 ft-lb.

3-22

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
4. Remove the water pump drive gear; then remove
the speed sensor housing assembly. Account for
two alignment pins, a gasket, and two seal washers.

FI538

2. Remove the water pump housing assembly noting
the location of the longer cap screw. Account for a
gasket and two alignment pins.
FI543

5. Remove the cap screws securing the magneto
cover to the crankcase. Note the location of the two
internal cap screws and the two longer cap screws.

FI539

FI596A

6. Remove the magneto cover and account for two
alignment pins and the gasket.
D. Rotor/Flywheel
E. Starter Clutch/Gear
F. Starter Motor
FI541

NOTE: Steps 1-6 in the preceding sub-section
must precede this procedure.

3. Remove two cap screws and the oil bolt securing
the oil pressure relief line to the engine. Account
for two crush washers and an O-ring.

7. Remove the nut securing the rotor/flywheel on the
crankshaft and install the crankshaft protector.

FI544

FI549

www.mymowerparts.com

3-23

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
8. Using the Magneto Rotor Remover Set, break the
rotor/flywheel loose from the crankshaft; then
remove the puller and crankshaft protector and
remove the rotor/flywheel.

FI559

12. Remove the shift detent cam arm and spring.

FI550

9. Remove the flywheel key from the crankshaft;
then remove the starter clutch gear.

FI560

13. Remove the snap ring securing the output drive
gear to the output shaft and remove the gear noting
that the hub flange is directed toward the crankcase.
FI551A

10. Remove starter idler gears and their respective
shafts; then remove the starter motor. Account for
an O-ring on the starter drive housing.

FI564

FI555

G. Shift Shaft
H. Drive Gear
NOTE: Steps 1-10 in the preceding sub-sections
must precede this procedure.

11. Remove the shift shaft noting a washer on each
end; then remove the cap screw securing the gear
shift cam plate and remove the plate from the shaft.
3-24

www.mymowerparts.com

FI566

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Servicing Left-Side
Components
INSPECTING STARTER
CLUTCH/GEAR
1. Place the starter clutch gear onto the rotor/flywheel and attempt to rotate the starter clutch gear
clockwise. It should lock up to the rotor/flywheel.
Rotate the gear counterclockwise and it should
turn freely. If it moves or locks up both ways, the
starter clutch must be replaced.
2. Inspect the starter clutch gear for chipped or missing teeth or discoloration/scoring of the clutch surface. Inspect the bearing for loose, worn, or
discolored rollers. If bearing is damaged, it must
be replaced.

FI570

2. Thoroughly clean the rotor/flywheel; then install
the new one-way clutch and secure with the cap
screws after applying a drop of red Loctite #271 to
the threads. Tighten to 26 ft-lb using a crisscross
pattern. Make sure the one-way bearing is installed
with the notches directed away from the rotor/flywheel.

FI576A

FI569

3. Inspect the one-way bearing for chipped surfaces,
missing rollers, or discoloration. If any of the
above conditions exist, replace the starter clutch
assembly.

FI578

REPLACING STARTER GEAR
BEARING
FI572

REPLACING STARTER CLUTCH
ASSEMBLY

1. Support the starter clutch gear in a press making
sure to support the hub around the entire circumference; then using a suitable bearing driver, press
the bearing from the gear.

1. Remove the cap screws securing the one-way
clutch assembly to the flywheel; then remove from
the flywheel.

www.mymowerparts.com

3-25

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
REPLACING STATOR COIL/
CRANKSHAFT POSITION SENSOR
1. Remove the three cap screws securing the stator
coil, two cap screws securing the crankshaft position sensor, and one cap screw from the harness
hold-down.
2. Lift the rubber grommet out of the housing; then
remove the stator coil/crankshaft position sensor.
Account for and note the position of the harness
hold-down under the crankshaft position sensor.
FI583

2. Thoroughly clean the gear hub; then apply a drop
of green Loctite #620 to the bearing outer race and
press into the gear hub until even with the lower
chamfer radius.

FI590

3. Install the new stator coil assembly and secure
with three cap screws using a drop of red Loctite
#271 on each. Tighten to 8 ft-lb.
FI580

INSPECTING STATOR/MAGNETO
COVER ASSEMBLY

4. Place the stator wire harness hold-down into position; then install the crankshaft position sensor and
secure with two cap screws. Tighten securely.
5. Install the upper cable hold-down and secure with
a cap screw. Tighten securely.

1. Inspect the stator for burned or discolored wiring,
broken or missing hold-down clips, or loose cap
screws.
2. Inspect the bearings in the magneto housing for
discoloration, roughness when rotated, and secure
fit in bearing bores.
3. Inspect the oil pressure relief valve for evidence of
metal chips or contamination. Do not disassemble
the valve.

FI595A

REPLACING MAGNETO COVER
BEARINGS
1. Using a suitable press and proper support, press
the bearing from the housing as indicated (one
from outside and one from inside).

FI588

3-26

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

FI593

MD1122

2. Install the starter motor and tighten the two cap
screws securely.
3. Install the shift detent cam making sure the washer
is installed.

3
FI594

2. Clean the bearing bores in the housing and inspect
closely for cracks or shiny areas indicating bearing
movement. Replace the housing if any of the
above are evident.
3. With a drop of red Loctite #271 around the bearing
bore, press a new bearing into the magneto cover
until the bearing is firmly seated in the bearing
bore.

MD1086

4. Install the shift detent cam arm and spring.
5. Install the gear shift shaft assembly and washer
making sure to align the alignment marks.

Installing Left-Side
Components
A. Starter Clutch/Gear
B. Rotor/Flywheel
1. If removed, place the crankshaft bearing retainer
into position. Apply red Loctite #271 to the three
cap screws. Install and tighten the three cap screws
securely.

FI559

6. Install starter idler gears (1) and (2).

www.mymowerparts.com

3-27

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

FI555A

FI547

7. Install the starter clutch gear onto the crankshaft;
then install the rotor/flywheel key in the crankshaft.

11. Install two alignment pins and a gasket on the
magneto cover; then install the water pump housing assembly. Tighten the cap screws to 8 ft-lb.

FI551A

FI541A

8. Install the rotor/flywheel and secure with the nut.
Tighten to 107 ft-lb.
C. Magneto Cover
D. Water Pump
NOTE: Steps 1-8 in the preceding sub-section
must precede this procedure.

9. Install two alignment pins and place the magneto
cover gasket into position. Install the magneto
cover. Noting the different-lengthed 6 mm cap
screws and the location of the two internal cap
screws, tighten cap screws in a crisscross pattern
to 8 ft-lb.

FI539

12. Install the water pump cover with a new O-ring
and secure with the four cap screws. Tighten to 8
ft-lb.

FI596A

10. Install the water pump drive gear and secure with
the nut. Tighten to 28 ft-lb.
3-28

www.mymowerparts.com

FI538

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
13. Connect the coolant hoses to the water pump and
secure with the hose clamps. Tighten securely.

Right-Side Components
AT THIS POINT
To service center crankcase components only, proceed
to Removing Right-Side Components.

KC142A

3. Mark the movable drive face and the fixed drive
face for installing purposes; then remove the nut
holding the movable drive face onto the crankshaft.

AT THIS POINT
To service any one specific component, only limited disassembly of components may be necessary. Note the
AT THIS POINT information in each sub-section.

NOTE: The engine/transmission does not have to
be removed from the frame for this procedure.

Removing Right-Side
Components
A. V-Belt Cover
B. Driven Pulley
C. Clutch Cover

MD1033

4. Remove the movable drive face and spacer.
Account for the movable drive face rollers and
outer drive face cover.

1. If the engine is still in the frame, remove the cap
screw securing the brake pedal to the pivot shaft.
Account for a flat washer.

MD1035

KC149A

2. Remove the cap screws securing the V-belt cover
to the clutch cover; then slide the brake pedal outward and remove the V-belt cover. Account for
two alignment pins and a gasket.

MD1034

www.mymowerparts.com

3-29

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

MD1036

MD1068

5. Using a 6 mm cap screw threaded into the fixed
driven face, spread the driven pulley by turning the
cap screw clockwise; then remove the V-belt.

8. Using an impact screwdriver, remove the three
Phillips-head cap screws holding the air intake
plate. Remove the air intake plate.

KC132

6. Remove the fixed drive face.

MD1092

9. Remove the cap screws holding the clutch cover
onto the right-side crankcase half. Note the positions of the different-lengthed cap screws for
installing purposes.
10. Using a rubber mallet, loosen the clutch cover;
then pull it away from the right-side crankcase
half. Account for two alignment pins and gasket.

MD1094

7. Remove the nut holding the driven pulley assembly; then remove the driven pulley assembly.

MD1115

D. Centrifugal Clutch Assembly
E. Oil Pump Drive Gear
F. Oil Pump Driven Gear
NOTE: Steps 1-10 in the preceding sub-section
must precede this procedure.

3-30

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
11. Remove the one-way clutch noting the direction of
the green dot or the word OUTSIDE for installing
purposes.

FI630

14. Remove the oil pump drive gear cap screw.
MD1286

12. Remove the left-hand threaded nut holding the
centrifugal clutch assembly.

CAUTION

Care must be taken when removing the nut; it has
“left-hand” threads.

MD1018

15. Remove oil pump drive gear. Account for the pin.

MD1014

MD1017

16. Remove the snap ring holding the oil pump driven
gear.

MD1016

13. Remove the cam chain.

MD1019

www.mymowerparts.com

3-31

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: Always use a new snap ring when installing the oil pump driven gear.

17. Remove oil pump driven gear. Account for the
drive pin and thrust washer.

MD1337

MD1020

AT THIS POINT
To service clutch components, see Servicing Right-Side
Components sub-section.

G. Oil Pump/Oil Strainer
NOTE: Steps 1-17 in the preceding sub-sections
must precede this procedure.

18. Remove three cap screws holding the oil pump
and remove the oil pump. Account for two alignment pins.

MD1208

AT THIS POINT
To service center crankcase components only, proceed
to Separating Crankcase Halves.

Servicing Right-Side
Components
NOTE: Whenever a part is worn excessively,
cracked, damaged in any way, or out of tolerance,
replacement is necessary.

INSPECTING CENTRIFUGAL
CLUTCH SHOE
MD1060

19. Remove the four cap screws securing the oil
strainer cap; then remove the Phillips-head screws
securing the oil strainer. Account for the O-ring.

1. Inspect the clutch shoe for uneven wear, chips,
cracks, or discoloration.
2. Inspect the depth of the grooves in the clutch
shoes. If any shoe is worn to the bottom of the
groove, replace the complete set.

CAUTION
Always replace clutch shoes as a complete set or
severe imbalance could occur.

3-32

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
3. Check that the clutch shoe can only be rotated
counterclockwise in respect to the clutch housing.
If the clutch shoe locks up or turns in both directions, the one-way clutch must be replaced.

ATV1014

INSPECTING CENTRIFUGAL
CLUTCH HOUSING
1. Inspect the clutch housing for burns, marks, scuffs,
cracks, scratches, or uneven wear.
2. If the housing is damaged in any way, the housing
must be replaced.
INSPECTING PRIMARY
ONE-WAY DRIVE
1. Place the one-way clutch onto the clutch shoe
assembly with the green dot or the word “OUTSIDE” directed away from the clutch shoe.

KC332A

INSPECTING OIL PUMP
1. Inspect the pump for damage.
2. It is inadvisable to remove the screw securing the
pump halves. If the oil pump is damaged, it must
be replaced.
NOTE: The oil pump is a non-serviceable component and must be replaced as a complete assembly.

DRIVEN PULLEY ASSEMBLY
NOTE: The driven pulley assembly is a non-serviceable component and must be replaced as a
complete assembly.

Installing Right-Side
Components
KC330

2. Place the clutch housing onto the clutch
shoe/one-way clutch.

A. Oil Strainer/Oil Pump

NOTE: It will be necessary to rotate the clutch
housing counterclockwise to properly seat the
one-way clutch.

1. Place the oil strainer into position beneath the
crankcase. Tighten the Phillips-head screws
securely.

KC331A

MD1337

www.mymowerparts.com

3-33

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
2. Place the strainer cap into position on the crankcase making sure the O-ring is properly installed
and secure with the four cap screws; then tighten
the oil drain plug to 16 ft-lb.

MD1019

5. Install the cam chain.
NOTE: Keep tension on the cam chain to avoid
damaging the crankcase boss.
MD1208

3. Place two alignment pins and the oil pump into
position on the crankcase and secure with the Phillips-head screws coated with red Loctite #271.
Tighten to 8 ft-lb.

6. Place the pin into position, install the oil pump
drive gear, and tighten the cap screw (coated with
red Loctite #271) to 63 ft-lb.

MD1017
MD1060

4. Place the thrust washer and drive pin into position
on the oil pump shaft, install the oil pump driven
gear making sure the recessed side of the gear is
directed inward, and secure with a new snap ring.
NOTE: Always use a new snap ring when installing the oil pump driven gear.

MD1018

7. Install the clutch shoe assembly on the crankshaft;
then install the flange nut (left-hand thread)
(coated with red Loctite #271). Tighten to 147
ft-lb.
NOTE: The flat side of the flange nut should be
directed towards the clutch shoe.
MD1020

CAUTION
Care must be taken when installing the flange nut; it has
“left-hand” threads.

3-34

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
8. Install the one-way clutch making sure that the
green dot or the word OUTSIDE is directed away
from the crankcase.

MD1342

MD1286

12. Place the driven pulley assembly into position and
secure with the nut (threads coated with red Loctite #271). Tighten to 147 ft-lb.

B. Clutch Cover
C. Fixed Drive Face
D. Movable Drive Face

NOTE: Steps 1-8 in the preceding sub-section
must precede this procedure.

9. Install two alignment pins and place the clutch
cover gasket into position. Install the clutch cover.

MD1068

MD1115

10. Tighten the clutch cover cap screws to 8 ft-lb.
KC134

13. Slide the fixed drive face assembly onto the front
shaft.
14. Spread the faces of the driven pulley by threading
a V-belt cover cap screw into the fixed driven face
and tightening until the faces open sufficiently to
allow the V-belt to drop into the pulley approximately 3/4 in.

MD1117

11. Install the air intake plate. Apply red Loctite #271
to the threads of the three Phillips-head cap
screws; then install and tighten securely.

www.mymowerparts.com

3-35

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

KC137

KC141

NOTE: The arrows on the V-belt should point in
direction of engine rotation.

NOTE: At this point, the cap screw can be
removed from the driven pulley face.

15. Making sure the movable drive face rollers are in
position, pinch the V-belt together near its center
and slide the spacer and movable drive face onto
the shaft.

17. Rotate the V-belt and drive/driven assemblies until
the V-belt is flush with the top of the driven pulley.
18. Install two alignment pins and place a new V-belt
cover gasket into position on the clutch cover. In a
crisscross pattern, tighten cap screws to 8 ft-lb.

KC127

16. Coat the threads of the nut with red Loctite #271;
then making sure the splines of the clutch shaft
protrude through the cover plate, secure with the
nut and tighten to 147 ft-lb.

KC142A

Center Crankcase
Components
NOTE: This procedure cannot be done with the
engine/transmission in the frame. Complete
Removing procedures for Top-Side, Left-Side, and
Right-Side must precede this procedure.

KC138

3-36

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Separating Crankcase
Halves
1. Remove the left-side and right-side cap screws
securing the crankcase halves noting the position
of the different-sized cap screws for joining purposes.

MD1313

Disassembling
Crankcase Half
NOTE: To aid in installing, it is recommended that
the assemblies be kept together and in order.
MD1006

NOTE: For steps 1-6, refer to illustration FI639A.

MD1012

2. Using Crankcase Separator/Crankshaft Remover
and tapping lightly with a rubber mallet, separate
the crankcase halves. Account for two alignment
pins.

CC869

FI639A

1. Remove the secondary driven shaft assembly (A)
noting the location of the front and rear bearing
locating pins and the center bearing locating ring.

FI660A

NOTE: To keep the shaft/gear assemblies intact
for identification, tap the shafts toward the
left-side crankcase half when separating the
halves.

www.mymowerparts.com

3-37

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

FI659A

FI646

FI661A

FI653A

2. Remove the reverse idler assembly (B). Account
for and note the location of the inner bushing (1),
idler shaft (2), and outer washer (3).

4. Remove the gear shift shaft (F) noting the inner
and outer washers.

FI641A

5. Remove the countershaft assembly (E) along with
the shift fork assembly.

FI650A

3. Remove the driveshaft (C); then pull the shift fork
locating shaft (D) out of the crankcase locating
boss and allow the shift forks to disengage from
the gear shift shaft (F).

FI662

3-38

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
6. Remove the crank balancer driven gear (G) and
account for a key; then remove the crankshaft balancer shaft.

SECONDARY GEARS
NOTE: When checking and correcting secondary
gear backlash and tooth contact, the universal
joint must be secured to the front shaft or false
measurements will occur.

Checking Backlash
NOTE: The rear shaft and bevel gear must be
removed for this procedure. Also, always start with
the original shims on the rear shaft.

1. Place the left-side crankcase cover onto the
left-side crankcase half to prevent runout of the
secondary transmission output shaft.
MD1024

7. Using Crankcase Separator/Crankshaft Remover
with the appropriate crankshaft protector, remove
the crankshaft.

2. Install the secondary driven output shaft assembly
onto the crankcase.
3. Mount the indicator tip of the dial indicator on the
secondary driven bevel gear (centered on the gear
tooth).
4. While rocking the driven bevel gear back and
forth, note the maximum backlash reading on the
gauge.
5. Acceptable backlash range is 0.05-0.33 mm
(0.002-0.013 in.).
Correcting Backlash
NOTE: If backlash measurement is within the
acceptable range, no correction is necessary.

MD1330

CAUTION
Do not remove the remaining output shaft assembly
unless absolutely necessary. If the shaft is removed, the
shaft nut must be replaced with a new one and the shaft
must be re-shimmed.

8. Remove the secondary drive gear/secondary
driven gear retaining nut. From inside the crankcase using a rubber mallet, drive out the output
shaft assembly. Account for the output shaft, a
shim, a washer, and the nut.

AT THIS POINT
To service crankshaft assembly, see Servicing Center
Crankcase Components sub-section.

Servicing Center
Crankcase Components
NOTE: Whenever a part is worn excessively,
cracked, damaged in any way, or out of tolerance,
replacement is necessary.

www.mymowerparts.com

1. If backlash measurement is less than specified,
remove an existing shim, measure it, and install a
new thinner shim.
2. If backlash measurement is more than specified,
remove an existing shim, measure it, and install a
thicker shim.
NOTE: Continue to remove, measure, and install
until backlash measurement is within tolerance.
Note the following chart.
Backlash Measurement

Shim Correction

Under 0.05 mm (0.002 in.)

Decrease Shim
Thickness

At 0.05-0.33 mm
(0.002-0.013 in.)

No Correction Required

Over 0.33 mm (0.013 in.)

Increase Shim
Thickness

Checking Tooth Contact
NOTE: After correcting backlash of the secondary driven bevel gear, it is necessary to check
tooth contact.

1. Remove the secondary driven output shaft assembly from the left-side crankcase half.

3-39

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
2. Clean the secondary driven bevel gear teeth of old
oil and grease residue.
3. Apply a thin, even coat of a machinist-layout dye
to several teeth of the gear.
4. Install the secondary driven output shaft assembly.
5. Rotate the secondary driven bevel gear several
revolutions in both directions.
6. Examine the tooth contact pattern in the dye and
compare the pattern to the illustrations.

If tooth contact pattern is comparable to an incorrect
pattern, correct tooth contact according to the following chart.
Tooth Contact

Shim Correction

Contacts at Top

Decrease Shim Thickness

Contacts at Root

Increase Shim Thickness

NOTE: To correct tooth contact, steps 1 and 2
(with NOTE) of “Correcting Backlash” must be followed and the above “Tooth Contact/Shim Correction” chart must be consulted.

CAUTION
After correcting tooth contact, backlash must again be
checked and corrected (if necessary). Continue the correcting backlash/correcting tooth contact procedures
until they are both within tolerance values.

CRANKSHAFT ASSEMBLY
NOTE: The crankshaft and connecting rod is a
non-serviceable assembly. If any component is
out of specification, the assembly must be
replaced.
ATV-0103

Measuring Connecting Rod
(Small End Inside Diameter)
1. Insert a snap gauge into the upper connecting rod
small end bore; then remove the gauge and measure it with micrometer.

ATV-0105

CC290D

2. Maximum diameter must not exceed specifications.
Measuring Connecting Rod
(Small End Deflection)
ATV-0104

Correcting Tooth Contact
NOTE: If tooth contact pattern is comparable to
the correct pattern illustration, no correction is
necessary.

3-40

www.mymowerparts.com

1. Place the crankshaft on a set of V-blocks and
mount a dial indicator and base on the surface
plate. Position the indicator contact point against
the center of the connecting rod small end journal.
2. Zero the indicator and push the small end of the
connecting rod away from the dial indicator.
3. Maximum deflection must not exceed specifications.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Measuring Connecting Rod
(Big End Side-to-Side)

Measuring Crankshaft
(Web-to-Web)

1. Push the lower end of the connecting rod to one
side of the crankshaft journal.
2. Using a feeler gauge, measure the gap between the
connecting rod and crankshaft journal.

1. Using a calipers, measure the distance from the
outside edge of one web to the outside edge of the
other web.

ATV-1017
CC289D

3. Acceptable gap range must be within specifications.
Measuring Crankshaft (Runout)
1. Place the crankshaft on a set of V blocks.
2. Mount a dial indicator and base on the surface
plate. Position the indicator contact at point 1 of
the crankshaft.

2. Acceptable width range must be within specifications.
COUNTERSHAFT

CAUTION
When disassembling the countershaft, care must be
taken to note the direction each major component (dog,
gear) faces. If a major component is installed facing the
wrong direction, transmission damage may occur
and/or the transmission will malfunction. In either case,
complete disassembly and assembly will be required.

Disassembling
1. Remove the reverse driven gear dog; then remove
the circlip securing the reverse driven gear.

ATV-1074

3. Zero the indicator and rotate the crankshaft slowly.

CAUTION
Care should be taken to support the connecting rod
when rotating the crankshaft.

FI663

4. Maximum runout must not exceed specifications.
NOTE: Proceed to check runout on the other end
of the crankshaft by positioning the indicator contact at point 2 and following steps 3-4.

www.mymowerparts.com

3-41

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
4. Remove the splined washer; then remove the circlip securing the high-low sliding dog. Remove
the sliding dog.

FI664

2. Remove the splined washer; then remove the
reverse driven gear along with the bearing and
bushing.

FI668

FI669
FI665

3. Remove the low driven gear washer; then remove
the low driven gear along with the bearing and
bushing.

5. Remove the circlip securing the high driven gear;
then remove a washer, the high driven gear along
with the bearing and bushing, and remove the high
driven washer.

FI666

FI670

FI667

FI671

3-42

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
ASSEMBLING
1. With the high driven washer (1) on the countershaft, install the high driven gear bushing (3),
bearings (2), and gear (4) on the countershaft; then
install the washers (5) and secure with the
snap-ring.

FI667A

FI671A

3
FI666

4. Place the reverse driven bushing (13) onto the
shaft; then install the bearing (14), gear (15), and
splined washer (16). Secure with a snap-ring.

FI670

2. Install the high/low shift dog (6) on the countershaft and secure with snap-ring (7); then install the
splined washer (8).

FI665A

FI668A

3. Install the low driven bushing (10), bearing (9),
and gear (11) on the countershaft; then install
splined washer (12).

FI664

5. Install the reverse dog on the shaft; then place the
shift forks and shift shaft into position.

www.mymowerparts.com

3-43

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

FI663

MD1079

2. Install and tighten the output shaft flange nut to 59
ft-lb. Using a punch, peen the nut.

FI662

NOTE: The countershaft assembly is now ready
to be installed.

Assembling Crankcase
Half

MD1333

3. Apply a liberal amount of oil to the crankshaft
bearing. Using a propane torch, heat the bearing
until the oil begins to smoke; then slide the crankshaft assembly into place.

NOTE: For ease of assembly, install components
on the right-side crankcase half.
NOTE: If the output shaft was removed, make
sure that the proper shim is installed.

1. Install the output shaft into the crankcase making
sure the two gears, shim, washer, and nut are in the
correct order.
MD1334

NOTE: If heating the bearing is not possible, the
crankshaft can be installed using a crankshaft
installer.

4. Rotate the crankshaft so the counterweight is
toward the rear of the engine. Install the crank balancer shaft.

MD1199

3-44

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

MD1024

FI662

5. Install the key in the crank balancer shaft; then
install the gear and aligning the timing marks,
slide the gear into place.

3
FI653

FI658

8. Align the shift forks to allow engagement with the
shift cam; then engage the shift forks and slide the
shift fork shaft into the locating boss in the crankcase.

6. Align the shift cam fork slots with the shift fork
shaft locating boss and with a washer on each end,
install in the crankcase.

FI653A

FI652A

7. Place the shift forks into position on the assembled
countershaft and install into the crankshaft as an
assembly.

FI655A

9. Install the input driveshaft.

www.mymowerparts.com

3-45

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

FI646

FI660A

10. Install the spacer (1), shaft (2), reverse idler gear,
and washer (3).

FI659A

FI641A

FI661A

FI645

11. Install the secondary output driveshaft assembly
into the crankcase half making sure the front and
rear bearing alignment pins are seated in the
recesses; then install the center carrier bearing
alignment C-ring.

3-46

www.mymowerparts.com

Joining Crankcase
Halves
1. Verify that the two alignment pins (A) are in place
and that both case halves are clean and grease free.
Apply Three Bond Sealant to the mating surfaces.
Place the right-side half onto the left-side half.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

FI639B

NOTE: Be sure to apply sealant to the inside
radius of all cap screw locations and the entire
surface of the internal cap screw bosses.

CC871

5. In a crisscross pattern, tighten the 8 mm cap
screws until the halves are correctly joined; then
tighten to 21 ft-lb.
NOTE: Rotate the shafts back and forth to ensure
no binding or sticking occurs.

6. In a crisscross pattern, tighten the 6 mm cap
screws to 10 ft-lb.
NOTE: Rotate the shafts back and forth to ensure
no binding or sticking occurs.

AT THIS POINT

FI639C

2. Using a plastic mallet, lightly tap the case halves
together until cap screws can be installed.
3. From the right side, install the crankcase cap
screws noting the location of the different-sized
cap screws; then tighten only until snug.
NOTE: Rotate the shafts back and forth to ensure
no binding or sticking occurs while tightening the
cap screws.

After completing center crankcase components, proceed to Installing Right-Side Components, to Installing
Left-Side Components, and to Installing Top-Side Components.

Installing
Engine/Transmission
1. From the left side, place the engine into the frame
(rear of engine first) tilting the rear up to allow
cylinder head to clear frame.
2. With engine moved rearward, engage the splines
of the front driveline into the front output drive
yoke; then move into position and install the two
through-bolts. Secure with lock nuts and tighten to
35 ft-lb.
3. Install the four cap screws securing the rear driveline
to the output drive flange and tighten to 20 ft-lb.
4. Connect coolant hoses (A) and (B) to the water
pump and connect the upper coolant hose to the
thermostat housing. Tighten all clamps securely.

MD1008

4. From the left side, install the remaining crankcase
cap screws; then tighten only until snug.
NOTE: Rotate the shafts back and forth to ensure
no binding or sticking occurs while tightening the
cap screws.

www.mymowerparts.com

3-47

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
9. From the top side, install the ECT sensor connector (C), fuel injector connector (D), MAP/IAT sensor connector (E), ISC connector (F), and the TPS
connector (G).

FI530B

FI522A

10. Place the air filter assembly into position and connect the crankcase breather securing with the
clamp; then connect the front air inlet duct and
secure with a hose clamp.
11. Install the harness connector onto the coil and
install the spark plug cap.
FI537

5. Install the exhaust pipe using a new seal at the cylinder head and loosely install the retaining cap
screws; then install the muffler with a new grafoil
seal and secure with two springs. Tighten the
exhaust pipe retainer cap screws to 20 ft-lb.
6. Connect the throttle cable and adjust free-play to
specifications (see Section 4); then tighten the
jam-nut securely and install the cover. Tighten the
screws securely.
7. Connect the stator connector (H) and crankshaft
position sensor connector (I) to the main harness;
then connect the positive cable to the starter motor
and tighten securely.

12. Connect the air ducts to the CVT housing and
tighten the clamps securely; then connect the air
duct to the air filter housing and the throttle body
and secure with the clamps.
13. Install the storage compartment and connect the
negative battery cable; then install the tool tray.
14. Pour the specified amount of coolant into the radiator and the specified amount and grade of oil into
the engine.
15. Install the left footwell support assembly, footwell,
and footrest. Tighten all fasteners securely.
16. Install the seat making sure it locks securely in
place; then start the engine and allow to warm up
while checking for leaks.
17. Shut engine off and inspect coolant and oil levels.
Add fluids as required.

FI534A

8. Connect the engine ground cable to the starter
mounting flange and secure with a cap screw tightened to 8 ft-lb.

3-48

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Table of Contents (1000)
Removing Engine/ Transmission........................... 3-49
Top-Side Components........................................... 3-53
Removing Top-Side Components ......................... 3-53
Servicing Top-Side Components........................... 3-57
Installing Top-Side Components ........................... 3-64
Left-Side Components .......................................... 3-71
Removing Left-Side Components ......................... 3-71
Installing Left-Side Components ........................... 3-73
Right-Side Components ........................................ 3-76
Removing Right-Side Components....................... 3-76
Servicing Right-Side Components ........................ 3-78
Installing Right-Side Components......................... 3-78
Center Crankcase Components............................ 3-80
Separating Crankcase Halves............................... 3-81
Disassembling Crankcase Half ............................. 3-82
Servicing Center Crankcase Components............ 3-83
Assembling Crankcase Half .................................. 3-91
Joining Crankcase Halves..................................... 3-93
Installing Engine/Transmission.............................. 3-94

3. Disconnect the IAT sensor connector; then loosen the
clamp securing the inlet air boot to the throttle body
and remove the air filter housing assembly.

GZ013

Removing Engine/
Transmission
GZ091A

Many service procedures can be performed without
removing the engine/transmission from the frame.
Closely observe the note introducing each sub-section for
this important information.

4. Using an absorbent towel, clean any spilled gasoline;
then press the gasline hose connectors and remove
from the fuel rails.

AT THIS POINT
If the technician’s objective is to service front Top-Side
Components, Left-Side Components, or Right-Side
Components, the engine/transmission does not have to
be removed from the frame.

AT THIS POINT
If the technician’s objective is to service/replace the oil
strainer (from beneath the engine/transmission), the
engine/transmission does not have to be removed from
the frame.

Secure the ATV on a support stand to elevate the wheels.

! WARNING
Make sure the ATV is solidly supported on the support
stand to avoid injury.

GZ124

5. Disconnect the TPS connector (A), MAP sensor connector (B), and ISC valve connector (C) from the
throttle body; then route the harness and connectors
away from the engine.

1. Remove the seat and tool tray; then remove the negative battery cable.
2. Remove the front rack, gauge pod, footwells and
footrests; then remove the front body panel (see Section 8).

www.mymowerparts.com

3-49

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ094A

NOTE: Using a suitable marker, mark the locations
of any ties that are removed to relocate wiring out of
the way.

GZ107

8. Disconnect the stator coil connector and the crankshaft
position sensor connector; then disconnect the gear position switch connector from the gear position switch.

6. Loosen the clamps securing the throttle body to the
intake manifolds; then remove the throttle body and
leaving the throttle cable connected, lay the assembly over the handlebar.

GZ069A

GZ090B

7. Disconnect the fuel injector wiring connectors; then
remove the intake manifolds leaving the injectors
installed.

GZ493A

9. Loosen the clamps securing the V-belt cooling ducts
to the V-belt housing; then disconnect the cooling
ducts.

GZ106

GZ037

3-50

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ103B

GZ099A

10. Remove the E-clips securing the shift linkage to the
shift lever and shift shaft; then remove the shift linkage. Account for two bushings and two flat washers.

14. Remove the front and rear spark plug wires from the
spark plugs; then disconnect the primary wire connectors from the coils and remove the coils from the
left side of the frame.

11. Remove the cap screws securing the rear driveshaft
yoke flange to the rear output flange.

GZ071A
GZ374

12. Remove the exhaust pipe springs at the muffler and
remove the muffler. Account for the grafoil seal.

15. Remove the cap screw securing the engine and harness grounds to the engine.

GZ064A
GZ372

13. Remove the nuts securing the rear exhaust pipe to the
cylinder; then remove the springs securing the rear
exhaust pipe to the front exhaust pipe and remove the
rear exhaust pipe. Account for a grafoil seal on the
pipe juncture and a seal in the cylinder.

www.mymowerparts.com

16. Remove the cap screws securing the upper bumper
support to the frame and swing the bumper forward
allowing access to the radiator drain plug.

3-51

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ068

GZ028

17. Place a suitable drain pan under the radiator; then
remove the radiator drain plug. Do not loosen the
radiator cap at this time.

GZ369A

GZ086A

18. Remove the bleed screw from the water pump; then
after coolant has drained, apply compressed air to the
bleed opening to purge the remaining coolant from
the system. Install the bleed screw and radiator drain
plug and tighten securely.

GZ008

20. Remove the flange nuts from the front and rear
engine through-bolts; then rock the engine slightly to
relieve engine mount pressure and remove the
through-bolts.

GZ009A

! WARNING
Always wear safety glasses when using compressed
air.

19. Remove the coolant hoses from the upper engine
coolant outlet pipes; then remove the lower coolant
hose from the water pump.
GZ118

3-52

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Top-Side Components
NOTE: For efficiency, it is preferable to remove and
disassemble only those components which need to
be addressed and to service only those components.
The technician should use discretion and sound
judgment.

AT THIS POINT
GZ104

21. Rotate the front driveshaft until the output yoke universal joint is in the vertical plane; then raise the
front of the engine/transmission until the front drive
splines disengage from the differential.

To service any one specific component, only limited disassembly of components may be necessary. Note the
AT THIS POINT information in each sub-section.

NOTE: The engine/transmission must be removed
to service the rear cylinder head, cylinder, and piston.

Removing Top-Side
Components

A. Valve Cover/Rocker Arms
B. Cylinder Head/Camshaft

GZ 110A

1. Remove the timing inspection plug, spark plugs, and
magneto housing cover; then install the 10 mm cap
screw (left-hand threads) in the crankshaft and rotate
the desired cylinder to top-dead-center of the compression stroke.

GZ117A

22. Fold the front drive line up and secure against the front
of the engine; then lift the engine clear of the mountings and remove from the right side of the frame.

GZ027

GZ026
GZ123

www.mymowerparts.com

3-53

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: Timing marks on the rotor/flywheel are
stamped with an “F” (front cylinder) and “R” (rear cylinder) adjacent to the mark.

GZ162

GZ063

GZ132A

GZ059

2. Remove the tappet covers on the cylinder being serviced. The tappets should not have pressure on them.

4. Remove the cap screw on the end of the tensioner;
then using a flat-blade screwdriver, turn the tensioner
clockwise to remove the tension. Remove the two
cap screws securing the tensioner adjuster assembly
and remove the assembly. Account for a gasket.

3. Remove the cap screws securing the valve cover to
the head; account for the four rubber washers on the
top side cap screws. Remove the valve cover.
Account for and note the orientation of the camshaft
plug. Note the location of two alignment pins.

GZ405

5. Using an awl, rotate the C-ring in its groove until it is
out of the cylinder head; then remove the C-ring.
NOTE: Care should be taken not to drop the C-ring
into the crankcase.
GZ126A

3-54

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ155

GZ136A

6. Bend the washer tabs down and remove the two cap
screws securing the sprocket to the camshaft; then
drop the sprocket off the camshaft.

3
GZ132B

GZ154A

9. Remove the cylinder head from the cylinder, remove
the gasket, and account for two alignment pins; then
remove the cam chain guide.

7. While holding the chain, slide the sprocket and camshaft out of the cylinder head.

GZ151

CC266D

NOTE: Loop the chain over the cylinder head and
secure it to keep it from falling into the crankcase.

8. Remove the five nuts securing the cylinder head to
the cylinder; then remove the four cylinder head cap
screws and washers.
NOTE: Removing the starter will simplify removal of
the front cylinder base nuts.
GZ161

www.mymowerparts.com

3-55

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
10. If the remaining cylinder head is to be serviced,
apply tension to the loose timing chain and rotate the
second cylinder to top-dead-center of the compression stroke; then repeat steps 2-9 on the other cylinder head.

AT THIS POINT
To service valves and cylinder head, see Servicing
Top-Side Components sub-section.

AT THIS POINT
To inspect cam chain guide, see Servicing Top-Side
Components sub-section.
GZ160A

C. Cylinders
D. Pistons
NOTE: Steps 1-10 in the preceding sub-section
must precede this procedure.

13. Lift the cylinder off the crankcase taking care not to
allow the piston to drop against the crankcase.
Account for the gasket and two alignment pins.

11. Remove the cap screws securing the water hose
union to the cylinder; then remove the union from
the cylinder. Account for an O-ring.

GZ142

GZ140A

12. Remove the two nuts securing the cylinder to the
crankcase.

GZ144

AT THIS POINT
To service cylinder, see Servicing Top-Side Components sub-section.

CAUTION
GZ141A

When removing the cylinder, be sure to support the piston to prevent damage to the crankcase and piston.

14. Using an awl, remove one piston-pin circlip.

3-56

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Servicing Top-Side
Components
NOTE: Whenever a part is worn excessively, cracked,
or damaged in any way, replacement is necessary.

VALVE ASSEMBLY

GZ145

When servicing valve assembly, inspect valve seats,
valve stems, valve faces, and valve stem ends for pits,
burn marks, or other signs of abnormal wear.

15. Using the Piston Pin Puller, remove the piston pin.
Account for the opposite-side circlip. Remove the
piston.

NOTE: Whenever a valve is out of tolerance, it must
be replaced.

NOTE: It is advisable to remove the opposite-side
circlip prior to using the puller.

Cleaning/Inspecting Valve Cover

NOTE: Support the connecting rod with rubber
bands or a piece of hose to avoid damaging the rod
or install the Connecting Rod Holder.

NOTE: If the valve cover cannot be trued, the cylinder head assembly must be replaced.

1. Wash the valve cover in parts-cleaning solvent.
2. Place the valve cover on the Surface Plate covered with
#400 grit wet-or-dry sandpaper. Using light pressure,
move the valve cover in a figure eight motion. Inspect
the sealing surface for any indication of high spots. A
high spot can be noted by a bright metallic finish. Correct any high spots before assembly by continuing to
move the valve cover in a figure eight motion until a
uniform bright metallic finish is attained.

CAUTION

GZ146A

Do not remove an excessive amount of the sealing surface or damage to the camshaft will result. Always
check camshaft clearance when resurfacing the valve
cover.

CAUTION
Do not allow the connecting rod to go down inside the
crankcase. If the rod is down inside the crankcase and
the crankshaft is rotated, severe damage will result.

NOTE: If the existing rings will not be replaced with
new rings, note the location of each ring for proper
installation. When replacing with new rings, replace
as a complete set only. If the piston rings must be
removed, remove them in this sequence.

A. Starting with the top ring, slide one end of the ring
out of the ring-groove.
B. Remove each ring by working it toward the dome
of the piston while rotating it out of the groove.

AT THIS POINT
To service piston, see Servicing Top-Side Components
sub-section.

CC130D

CAUTION
Water or parts-cleaning solvent must be used in conjunction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

AT THIS POINT
To service center crankcase components only, proceed
to Removing Left-Side Components.

www.mymowerparts.com

3-57

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Removing Valves
NOTE: Index all valves, springs, and cotters to their
original position when removing. When installing, all
valve components should be installed in their original
position.

1. Using a valve spring compressor, compress the valve
springs and remove the valve cotters. Account for an
upper spring retainer.

ATV-1082

2. Maximum runout must not exceed specifications.
Measuring Valve Stem Outside
Diameter
1. Using a micrometer, measure the valve stem outside
diameter.
2. Acceptable diameter range must be within specifications.
CC132D

2. Remove the valve seal and the lower remaining
spring seat. Discard the valve seal.

Measuring Valve Face/Seat Width
1. Using a micrometer, measure the width of the valve
face.

CC136D

NOTE: The valve seals must be replaced.

3. Remove the valve springs; then invert the cylinder
head and remove the valves.
Measuring Valve Stem Runout
1. Support each valve stem end with the V Blocks; then
check the valve stem runout using a dial indicator.

ATV-1004

2. Acceptable width (intake valve) must not exceed
specifications.
3. Acceptable width (exhaust valve) must not exceed
specifciations.
Measuring Valve Face Radial Runout
1. Mount a dial indicator on the surface plate; then
place the valve stem on a set of V blocks.
2. Position the dial indicator contact point on the outside edge of the valve face; then zero the indicator.

3-58

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Servicing Valves/Valve Guides/Valve
Seats
If valves, valve guides, or valve seats require servicing or
replacement, Arctic Cat recommends that the components be taken to a qualified machine shop for servicing.

CAUTION
If valves are discolored or pitted or if the seating surface is worn, the valve must be replaced. Do not attempt
to grind the valves or severe engine damage may occur.

ATV1082A

3. Rotate the valve in the V blocks.

Measuring Rocker Arm
(Inside Diameter)

4. Maximum runout must not exceed specifications.

1. Using a dial calipers, measure the inside diameter of
the rocker arm.

Measuring Valve Guide/Valve Stem
Deflection (Wobble Method)

2. Acceptable inside diameter range must be within
specifications.

1. Mount a dial indicator and base on the surface plate;
then place the cylinder head on the surface plate.
2. Install the valve into the cylinder head; then position
the dial indicator contact point against the outside
edge of the valve face. Zero the indicator.

Measuring Rocker Arm Shaft
(Outside Diameter)
1. Using a micrometer, measure the outside diameter of
the rocker arm shaft.
2. Acceptable outside diameter range must be within
specifications.
Installing Valves
1. Apply grease to the inside surface of the valve seals;
then place a lower spring seat and valve guide seal
over each valve guide.

CC131D

3. Push the valve from side to side; then from top to
bottom.
4. Maximum “wobble” deflection must not exceed
specifications.
Measuring Valve Guide
(Inside Diameter)
1. Insert a snap gauge 1/2 way down into each valve
guide bore; then remove the gauge and measure it
with a micrometer.
2. Acceptable inside diameter range must be within
specifications.
3. If a valve guide is out of tolerance, it must be
replaced.

www.mymowerparts.com

CC144D

2. Insert each valve into its original location.
3. Install the valve springs with the painted end of the
spring facing away from the cylinder head.
NOTE: If the paint is not visible, install the ends of
the springs with the closest wound coils toward the
head.

3-59

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: If the existing rings will not be replaced with
new ones, note the location of each ring for proper
installation. When installing new rings, install as a
complete set only.

Cleaning/Inspecting Piston Rings
1. Take an old piston ring and snap it into two pieces;
then grind the end of the old ring to a 45° angle and
to a sharp edge.
2. Using the sharpened ring as a tool, clean carbon from
the ring-grooves. Be sure to position the ring with its
tapered side up.
ATV-1011A

4. Place a spring retainer over the valve springs; then
using the valve spring compressor, compress the
valve springs and install the valve cotters.

CAUTION

PISTON ASSEMBLY

Improper cleaning of the ring-grooves by the use of the
wrong type of ring-groove cleaner will result in severe
damage to the piston.

NOTE: Whenever a piston, rings, or pin are out of
tolerance, they must be replaced.

Measuring Piston-Ring End Gap
(Installed)

Cleaning/Inspecting Piston
1. Using a non-metallic carbon removal tool, remove
any carbon buildup from the dome of the piston.
2. Inspect the piston for cracks in the piston pin, dome,
and skirt areas.

1. Place each compression ring in the wear portion of
the cylinder. Use the piston to position each ring
squarely in the cylinder.
2. Using a feeler gauge, measure each piston-ring end
gap. Acceptable ring end gap must not exceed specifications.

3. Inspect the piston for seizure marks or scuffing.
Repair with #400 grit wet-or-dry sandpaper and
water or honing oil.
NOTE: If scuffing or seizure marks are too deep to
correct with the sandpaper, replace the piston.

4. Inspect the perimeter of each piston for signs of
excessive “blowby.” Excessive “blowby” indicates
worn piston rings or an out-of-round cylinder.
Removing Piston Rings
1. Starting with the top ring, slide one end of the ring
out of the ring-groove.

CC280D

Measuring Piston Pin (Outside
Diameter) and Piston-Pin Bore
1. Measure the piston pin outside diameter at each end
and in the center. If measurement exceeds specifications, the piston pin must be replaced.

CC400D

2. Remove each ring by working it toward the dome of
the piston while rotating it out of the groove.

3-60

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

ATV-1070

GZ168

2. Insert an inside dial indicator into the piston-pin
bore. The diameter must not exceed specifications.
Take two measurements to ensure accuracy.

3
GZ169A

2. Install the second compression ring with the marking
“E TOP” directed toward the top of the piston.
ATV-1069

Measuring Piston Skirt/Cylinder
Clearance
1. Measure the cylinder front to back in six places.

GZ167

3. Install the first (unmarked) compression ring; then
rotate the rings so the ring gaps are approximately
180° apart and oriented to the piston pin.

CC127D

2. Measure the corresponding piston diameter at a point
15 mm (0.6 in.) above the piston skirt at a right angle
to the piston-pin bore. Subtract this measurement
from the measurement in step 1. The difference
(clearance) must not exceed specifications.
Installing Piston Rings
1. Install the expander spring making sure the ends are
aligned on the wire; then install the oil ring with the
ring gap 90° from the spring gap and the marking “E
TOP” directed toward the top of the piston.

www.mymowerparts.com

GZ187A

3-61

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Cleaning/Inspecting Cylinder

CAUTION
Incorrect installation of the piston rings will result in
engine damage.

CYLINDER/CYLINDER HEAD
ASSEMBLY
NOTE: If the cylinder/cylinder head cannot be trued,
they must be replaced as an assembly.

Cleaning/Inspecting Cylinder Head

CAUTION
The cylinder head studs must be removed for this procedure.

1. Using a non-metallic carbon removal tool, remove
any carbon buildup from the combustion chamber
being careful not to nick, scrape, or damage the combustion chamber or the sealing surface.

1. Wash the cylinder in parts-cleaning solvent.
2. Inspect the cylinder for pitting, scoring, scuffing,
warpage, and corrosion. If marks are found, repair
the surface using a cylinder hone (see Inspecting
Cylinder in this sub-section).
3. Place the cylinder on the surface plate covered with
#400 grit wet-or-dry sandpaper. Using light pressure,
move the cylinder in a figure eight motion. Inspect
the sealing surface for any indication of high spots.
A high spot can be noted by a bright metallic finish.
Correct any high spots before assembly by continuing to move the cylinder in a figure eight motion
until a uniform bright metallic finish is attained.

CAUTION
Water or parts-cleaning solvent must be used in conjunction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

2. Inspect the spark plug hole for any damaged threads.
Repair damaged threads using a “heli-coil” insert.
3. Place the cylinder head on the surface plate covered
with #400 grit wet-or-dry sandpaper. Using light
pressure, move the cylinder head in a figure eight
motion. Inspect the sealing surface for any indication
of high spots. A high spot can be noted by a bright
metallic finish. Correct any high spots before assembly by continuing to move the cylinder head in a figure eight motion until a uniform bright metallic
finish is attained.

CAUTION

CC129D

Water or parts-cleaning solvent must be used in conjunction with the wet-or-dry sandpaper or damage to
the sealing surface may result.

Measuring Cylinder Head Distortion
1. Remove any carbon buildup in the combustion
chamber.
2. Lay a straightedge across the cylinder head; then
using a feeler gauge, check the distortion factor
between the head and the straightedge.
3. Maximum distortion must not exceed specifications.

CC141D

3-62

www.mymowerparts.com

Inspecting Cam Chain Guide
1. Inspect cam chain guide for cuts, tears, breaks, or
chips.
2. If the chain guide is damaged, it must be replaced.
Inspecting Cylinder
1. Using a slide gauge and a dial indicator or a snap
gauge, measure the cylinder bore diameter in three
locations from top to bottom and again from top to
bottom at 90° from the first measurements for a total
of six measurements. The trueness (out-of-roundness) is the difference between the highest and lowest reading. Maximum trueness (out-of-roundness)
must be within specifications.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

CC127D

2. Wash the cylinder in parts-cleaning solvent.
3. Inspect the cylinder for pitting, scoring, scuffing, and
corrosion. If marks are found, repair the surface
using a #320 grit ball hone.
NOTE: To produce the proper 60° cross-hatch pattern, use a low RPM drill (600 RPM) at the rate of 30
strokes per minute. If honing oil is not available, use
a lightweight petroleum-based oil. Thoroughly clean
cylinder after honing using soap and hot water. Dry
with compressed air; then immediately apply oil to
the cylinder bore. If the bore is severely damaged or
gouged, replace the cylinder.

CC283D

2. Rotate the camshaft and note runout; maximum
runout must not exceed specifications.
Measuring Camshaft Lobe Height
1. Using a calipers, measure each cam lobe height.

ATV1013A

2. The lobe heights must be greater than minimum
specifications.
Inspecting Camshaft Bearing
Journal
CC390D

4. If any measurement exceeds the limit, replace the
cylinder and piston.
Measuring Camshaft Runout
NOTE: If the camshaft is out of tolerance, it must be
replaced.

1. Inspect the bearing journal for scoring, seizure
marks, or pitting.
2. If excessive scoring, seizure marks, or pitting is
found, the cylinder head assembly must be replaced.
Measuring Camshaft to
Cylinder Head Clearance
1. Remove the adjuster screws and jam nuts.

1. Place the camshaft on a set of V blocks; then position
the dial indicator contact point against the shaft and
zero the indicator.

CC005D

www.mymowerparts.com

3-63

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
2. Place a strip of plasti-gauge in each of the camshaft
lands in the cylinder head.
3. Place the valve cover on the cylinder head and secure
with the valve cover cap screws. Tighten securely.
NOTE: Do not rotate the camshaft when measuring
clearance.

4. Remove the cap screws securing the valve cover to
the cylinder; then remove the valve cover and camshaft.
5. Match the width of the plasti-gauge with the chart
found on the plasti-gauge packaging to determine
camshaft to cylinder head and valve cover clearance.

CF061A

CF060A
CC145D

6. If clearance is excessive, measure the journals of the
camshaft.

2. If damaged, the camshaft must be replaced.

Installing Top-Side
Components
A. Pistons
B. Cylinders
1. Install the piston on the connecting rod making sure
the circlip on each side is fully seated in the piston.
NOTE: The piston should be installed so the arrow
points toward the exhaust of the respective cylinder.
CC287D

NOTE: If the journals are worn, replace the camshaft; then measure the clearance again. If it is still
out of tolerance, replace the cylinder head.

Inspecting Camshaft Spring/Drive
Pin (Front Camshaft Only)
1. Inspect the spring and drive pin for damage.

GZ166

2. Place the two alignment pins into position. Place the
cylinder gasket into position; then place a piston
holder (or suitable substitute) beneath the piston skirt
and square the piston in respect to the crankcase.
3-64

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ159

GZ160A

3. Lubricate the inside wall of the cylinder; then using a
ring compressor, compress the rings and slide the
cylinder over the piston. Route the cam chain up
through the cylinder cam chain housing; then remove
the piston holder and seat the cylinder firmly on the
crankcase.

5. Install the coolant hose onto the crankcase union and
tighten the clamp.

CAUTION
The cylinder should slide on easily. Do not force the cylinder or damage to the piston, rings, cylinder, or crankshaft assembly may occur.

C. Cylinder Head
D. Valve Cover
NOTE: Steps 1-5 in the preceding sub-section must
precede this procedure.

6. Place the chain guide into the cylinder.

CAUTION
Care should be taken that the bottom of the chain guide
is secured in the crankcase boss.

GZ142

4. Loosely install the two nuts securing the cylinder to
the crankcase.
NOTE: The two cylinder-to-crankcase nuts will be
tightened in step 10.

GZ161A

7. Place a new head gasket into position on the cylinder.
Place the alignment pins into position; then place the
head assembly into position on the cylinder while
guiding the cam chain through the cylinder head.

GZ141A
GZ151

8. Apply a light coat of grease to the cylinder head cap
screw threads and washers; then install the cap screws.

www.mymowerparts.com

3-65

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: At this point, oil the camshaft bearings, cam
lobes, and the three seating journals on the cylinder.

13. With the cam lobes directed down (toward the piston), maneuver the camshaft/sprocket assembly
through the chain and towards its seating position;
then loop the chain over the sprocket.

GZ132B

NOTE: Note the position of the alignment marks on
the end of the camshaft. They must be parallel with
the valve cover mating surface. If rotating the camshaft and sproket is necessary for alignment, do not
allow the crankshaft to rotate and be sure the cam
lobes end up in the down position.

9. Loosely install the five cylinder head nuts.
10. In a crisscross pattern, tighten the four cylinder head
cap screws (from step 8) initally to 20 ft-lb; then
increase to 30 ft-lb, and finally to 37 ft-lb. Tighten
the 8 mm nut (from step 9) to 18 ft-lb; then using a
crisscross pattern, tighten the 6 mm nuts (from step
9) to 8 ft-lb. Tighten the two cylinder-to-crankcase
nuts (from step 4) securely.
NOTE: If both cylinders have been removed, repeat
steps 1-10 for the remaining cylinder.

11. With the timing inspection plug removed and the
chains held tight, rotate the crankshaft until the front
piston is at top-dead-center.
12. With the alignment pin installed in the camshaft,
loosely place the cam sprocket (with the recessed side
facing the cam shaft lobes) onto the camshaft. At this
point, do not “seat” the sprocket onto the shaft.

GZ190C

14. Seat the cam sprocket onto the camshaft making sure
the alignment pin in the camshaft aligns with the
smallest hole in the sprocket; then place the camshaft/sprocket assembly onto the cylinder ensuring
the following.

GZ190B

732-307B

A. Piston still at top-dead-center.
B. Camshaft lobes directed down (toward the piston).
C. Camshaft alignment marks parallel to the valve
cover mating surface.
D. Recessed side of the sprocket directed toward the
cam lobes.
E. Camshaft alignment pin and sprocket alignment
hole (smallest) are aligned.
GZ130

3-66

www.mymowerparts.com

CAUTION
If any of the above factors are not as stated, go back to
step 11 and carefully proceed.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
15. Place the tab-washer onto the sprocket making sure it
covers the pin in the alignment hole.

18. Rotate the crankshaft until the first cap screw (from
step 16) can be tightened; then tighten to 10 ft-lb.
Bend the tab to secure the cap screw.

AT THIS POINT
Return the engine to TDC on the front cylinder making
sure the cam lobes are directed downward to ensure
correct starting point for step 19.

19. Keeping tension on the rear cam chain, rotate the
engine forward 270° until rear piston is at TDC indicated by timing mark R.

ATV1027

CAUTION
Care must be taken that the tab-washer is installed correctly to cover the alignment hole on the sprocket. If the
alignment pin falls out, severe engine damage will result.

16. Install the first cap screw (threads coated with red
Loctite #271) securing the sprocket and tab-washer
to the camshaft. Tighten only until snug.
GZ060

20. With the cam lobes directed down (toward the piston), maneuver the camshaft/sprocket assembly
through the chain and towards its seating position;
then loop the chain over the sprocket.
NOTE: Note the position of the alignment marks on
the end of the camshaft. They must be parallel with
the valve cover mating surface. If rotating the camshaft and sproket is necessary for alignment, do not
allow the crankshaft to rotate and be sure the cam
lobes end up in the down position.
GZ195

17. Keeping tension on the opposite cam chain, rotate
the crankshaft until the second cap screw securing
the sprocket to the camshaft can be installed; then
install the cap screw (threads coated with red Loctite
#271) and tighten to 10 ft-lb. Bend the tab to secure
the cap screw.

CAUTION
Failure to keep tension on any loose cam chain may
cause severe engine damage.
GZ190C

GZ193

www.mymowerparts.com

3-67

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ190B

21. Seat the cam sprocket onto the camshaft making sure
the alignment pin in the camshaft aligns with the
smallest hole in the sprocket; then place the camshaft/sprocket assembly onto the cylinder ensuring
the following.

ATV-1027

CAUTION
Care must be taken that the tab-washer is installed correctly to cover the alignment hole on the sprocket. If the
alignment pin falls out, severe engine damage will
result.

23. Install the first cap screw (threads coated with red
Loctite #271) securing the sprocket and tab-washer
to the camshaft. Tighten only until snug.

732-307B

A. Piston still at top-dead-center.
B. Camshaft lobes directed down (toward the piston).
C. Camshaft alignment marks offset 5° from the
valve cover mating surface.
D. Recessed side of the sprocket directed toward the
cam lobes.

GZ195

24. Rotate the crankshaft until the second cap screw
securing the sprocket to the camshaft can be
installed; then install the cap screw (threads coated
with red Loctite #271) and tighten to 10 ft-lb. Bend
the tab to secure the cap screw.

E. Camshaft alignment pin and sprocket alignment
hole (smallest) are aligned.

CAUTION
If any of the above factors are not as stated go back to
step 19 and carefully proceed.

22. Place tab-washer onto the sprocket making sure it
covers the pin in the alignment hole.

GZ193

3-68

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

CD465

CD468

25. Rotate the crankshaft until the first cap screw (from
step 23) can be addressed; then tighten to 10 ft-lb.
Bend the tab to secure the cap screw.

28. Remove the cap screw from the end of the chain tensioner; then using a flat-blade screwdriver, rotate the
adjuster screw inside the tensioner clockwise until
the screw bottoms.

GZ194

26. Place the C-rings into position in their grooves in the
cylinder heads.

CD501

NOTE: The adjuster shaft will be drawn into the tensioner as the adjuster screw is rotated clockwise. The
adjuster shaft tension will be released in step 30.

29. Place the chain tensioner adjuster assembly and gasket into position on the cylinder and secure with the
two cap screws.

CC012D

27. Install the cylinder head plugs in the cylinder heads
with the open end facing downward and toward the
inside.

CAUTION
The open end of the plug must be positioned downward.

www.mymowerparts.com

CD469

30. Using a flat-blade screwdriver, rotate the adjuster
screw inside the tensioner counterclockwise until all
tension is released; then install the cap screw into the
end of the chain tensioner.

3-69

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
33. Lubricate the camshaft journals and lobes with
engine oil; then place the valve cover into position.

GZ201

GZ206

NOTE: At this point, the rocker arms and adjuster
screws must not have pressure on them.

34. Install the top side cap screws with rubber washers;
then install the remaining cap screws. Tighten only
until snug.

CD471

31. Loosen the four adjuster screw jam nuts; then loosen
the four adjuster screws on the rocker arms in the
valve cover.

CC003D

35. In a crisscross pattern starting from the center and
working outward, tighten the cap screws on both
valve covers securely.
36. Adjust valve/tappet clearance (see Section 2).

GZ199

37. Place the tappet covers into position making sure the
O-rings are properly installed. Tighten the cap
screws securely.

32. Apply a thin coat of Three Bond Sealant to the mating surfaces of the cylinder heads.

GZ208

38. If removed, install the spark plugs. Tighten securely.
GZ202

3-70

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Left-Side Components
NOTE: For efficiency, it is preferable to remove and
disassemble only those components which need to
be addressed and to service only those components.
The technician should use discretion and sound
judgment.

AT THIS POINT
To service any one specific component, only limited disassembly of components may be necessary. Note the
AT THIS POINT information in each sub-section.

NOTE: The engine/transmission does not have to
be removed from the frame for this procedure.

GZ224A

NOTE: The starter is not serviceable and must be
replaced as a complete assembly.

3. Remove the rotor/flywheel nut; then install the
appropriate crankshaft protector into the crankshaft.

Removing Left-Side
Components
A.
B.
C.
D.
E.

Magneto Cover/Stator Coils
Water Pump
Shifter Assembly
Rotor/Flywheel/Starter Clutch
Speed Sensor/Trigger Assembly

1. Remove the cap screws securing the magneto cover
to the crankcase; then remove the magneto cover.
Account for the gasket.

PR440

4. Install Magneto Rotor Remover Set and loosen the
rotor/flywheel; then remove the crankshaft protector
and rotor/flywheel from the crankshaft. Account for
the flywheel key.

GZ212A

2. Remove the starter motor, starter driven gear (A),
starter countershaft bushing (B), and starter countershaft gear (C); then remove the starter gear shafts (D)
noting that the longer shaft is nearest the starter.

www.mymowerparts.com

GZ216

NOTE: The puller has left-hand threads.

3-71

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
7. Remove the two cap screws securing the water pump
to the crankcase; then remove the water pump.
Account for an O-ring.

GZ217

5. With the flywheel key removed, remove the starter
ring-gear and spacer washer.
GZ230A

NOTE: The water pump is a non-serviceable component and must be replaced as a complete assembly.

8. Remove the cap screws securing the gear shift cover
to the crankcase; then remove the gear shift cover.
Account for a gasket and washer.
NOTE: Inspect the inside of the left-side cover for
any shaft washers that may have come off with the
cover. Make sure they are returned to their respective
shafts.
GZ226

GZ231A
GZ249

6. Remove the hose clamps from the water pump; then
remove the coolant hoses from the water pump outlets and coolant pipes.

GZ233A

9. Remove the nut (A) from the shift cam stopper bolt
(B); then remove the cam stopper spring (C).
Account for a flat washer (D).
GZ218

3-72

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ236A

GZ235

10. Remove the cap screw securing the shift cam plate to
the shift cam shaft and remove the shift cam plate;
then remove the shift shaft. Account for a washer.

12. Remove the cap screws securing the oil filler cover
to the crankcase; then remove the cover. Account for
an O-ring.

GZ234B

11. Remove the cap screws securing the speed sensor
housing to the crankcase and remove the housing
assembly; then remove the snap ring securing the
speed sensor trigger to the shaft and remove the trigger. Account for a gasket.
NOTE: It may be necessary to use a small two-jaw
puller to remove the trigger.

GZ250

Installing Left-Side
Components
1. Thoroughly clean all gasket material and sealant
from mating surfaces.
2. Install a new O-ring on the oil filler cover and coat it
with clean engine oil; then install the oil filler cover
into the crankcase and secure with the cap screws.
Tighten to 8 ft-lb.

GZ243

GZ250

www.mymowerparts.com

3-73

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
3. Clean the countershaft and trigger splines throughly
and install the inner snap ring onto the shaft; then
apply green Loctite #620 to the trigger and countershaft splines and install the trigger. Secure with a flat
washer and outer snap ring.

GZ255

GZ253

GZ256

6. Install the shift cam stopper spring onto the shift cam
stopper and secure with a flat washer and flange nut.
Tighten to 8 ft-lb.
GZ254

4. Using a new gasket, install the speed sensor housing
onto the crankcase and secure with two cap screws.
Tighten to 8 ft-lb.

GZ259

7. Install the shift cam plate onto the shift cam shaft and
secure with the cap screw. Tighten to 8 ft-lb.

GZ232

5. If removed, install the shift cam stopper on the support; then with the flat washer in place, install the
shift cam stopper assembly into the crankcase and
tighten to 8 ft-lb.

GZ260

3-74

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
8. Install the shift shaft into the crankcase making sure
the washers are properly located; then align the timing reference marks and completely seat the shift
shaft.

GZ249

GZ258

3
GZ226

GZ261

9. Apply grease to the lips of the shift shaft seal in the
shifter housing; then using a new gasket, install the
shifter housing and secure with the cap screws.
Tighten in a crisscross pattern to 8 ft-lb.

11. Place the key into the keyway in the crankshaft; then
wipe all oil from the crankshaft surface and rotor/flywheel bore and install the rotor/flywheel onto the
crankshaft aligning the keyway with the key. Secure
with the nut and tighten to 107 ft-lb.

GZ225

CAUTION
GZ262

10. Install the spacer washer on the crankshaft; then
install the starter ring gear.

Make sure the one-way starter clutch is properly
engaged with the starter ring gear before installing and
tightening the rotor/flywheel nut or damage to the
clutch assembly could occur.

12. Install the starter driven and counter gear shafts (D)
into the crankcase (longer shaft to the front); then
install the starter countershaft gear (C), starter driven
gear (A), and bushing (B) making sure the chamfered gear teeth on the countershaft gear are directed
outward.

www.mymowerparts.com

3-75

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
AT THIS POINT
To service any one specific component, only limited disassembly of components may be necessary. Note the
AT THIS POINT information in each sub-section.

NOTE: The engine/transmission does not have to
be removed from the frame for this procedure.

Removing Right-Side
Components

GZ224A

13. Install the starter motor with a new O-ring lightly
lubricated with grease; then tighten the mounting cap
screws to 8 ft-lb.

A.
B.
C.
D.

V-Belt Cover
Driven Pulley
Clutch Cover
Centrifugal Clutch

1. Remove the cap screws securing the V-belt cover;
then using a rubber mallet, gently tap on the cover
tabs to loosen the cover. Account for a gasket and
two alignment pins.

GZ251

14. Place the seal protector into the end of the crankshaft; then install the magneto cover using a new
gasket and secure with the cap screws. Using the pattern shown, tighten to 8 ft-lb.

GZ244B

2. Remove the nut securing the movable drive face;
then remove the face. Account for a spacer and a flat
washer.

GZ212B

Right-Side Components
NOTE: For efficiency, it is preferable to remove and
disassemble only those components which need to be
addressed and to service only those components. The
technician should use discretion and sound judgment.

3-76

www.mymowerparts.com

GZ074

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

CD966A

GZ246B

3. Remove the V-belt.
4. Remove the nut securing the fixed driven assembly;
then remove the assembly.

3
GZ247A

NOTE: To aid in installing, it is recommended that
the assemblies are kept together and IN ORDER.
PR388

5. Remove the fixed drive face.
6. Remove the cap screws securing the V-belt housing
to the crankcase; then remove the V-belt housing.
Account for two alignment pins.

8. Remove the one-way clutch from the centrifugal
clutch. Note the location of the green dot (or the
word OUTSIDE) for installing purposes.

GZ247B

GZ246A

7. Remove the cap screws securing the clutch cover;
then using a rubber mallet, carefully remove the
cover. Account for two alignment pins.

www.mymowerparts.com

9. Using a hydraulic press, remove the clutch housing
assembly from the clutch cover. Account for the left
fixed drive spacer and an O-ring inside the fixed
drive spacer.

3-77

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
INSPECTING CENTRIFUGAL CLUTCH
SHOE
1. Inspect the clutch shoes for uneven wear, chips,
cracks, or discoloration. If any shoe is damaged,
replace the complete set.
2. Inspect the clutch shoes for wear or damage. If any
shoe is worn to the bottom of the groove, replace the
complete set.

CAUTION
CF085

Always replace the clutch shoes as a complete set or
severe imbalance could occur.

CC596

NOTE: Account for and inspect the clutch housing
seal.

10. Remove the nut (left-hand threads) securing the
clutch shoe assembly.

ATV1014

INSPECTING CLUTCH HOUSING
1. Inspect the clutch housing for burns, grooving,
cracks, or uneven wear.
2. If the housing is damaged in any way, the housing
must be replaced.
INSPECTING PRIMARY
ONE-WAY DRIVE
1. Insert the drive into the clutch housing.
2. Rotate the inner race by hand and verify the inner
race rotates only one direction.
3. If the inner race is locked in place or rotates both
directions, the drive assembly must be replaced.
DRIVEN PULLEY ASSEMBLY

GZ248A

Servicing Right-Side
Components
NOTE: Whenever a part is worn excessively,
cracked, damaged in any way, or out of tolerance,
replacement is necessary.

NOTE: The driven pulley is a non-serviceable component. If the pulley faces, cam ramps, or sheeve
bushing are worn or loose, the pulley must be
replaced as an assembly. Do not disassemble the
driven pulley.

Installing Right-Side
Components
1. Install the clutch shoe assembly and secure with the
flange nut (threads coated with red Loctite #271).
Tighten to 221 ft-lb.

3-78

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ241

GZ246B

2. Install the clutch cover alignment pins into the crankcase, apply oil to the cover gasket, and install the
gasket onto the crankcase.

7. Making sure the alignment pins are correctly
installed, place a bead of silicone sealant on the mating surfaces and install the V-belt housing. Secure
with the cap screws tightened to 8 ft-lb.

3. Apply grease to the outer edges of the clutch housing; then from inside the clutch cover, install the
clutch housing into the cover.
4. Lightly grease the clutch housing seal; then insert the
left fixed drive spacer.

GZ263B

CF088A

5. Install the one-way clutch onto the clutch shoe
assembly.

GZ244A

8. Place the driven pulley assembly into position and
secure with the nut (coated with red Loctite #271).
Tighten to 80 ft-lb.

GZ247

CAUTION
When installed correctly, the green alignment dot (or the
word OUTSIDE) on the one-way clutch is visible.

6. Place the clutch cover/clutch housing assembly into
position on the crankcase; then secure with the cap
screws. Tighten in a crisscross pattern to 8 ft-lb.

www.mymowerparts.com

3-79

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ066

GZ075

10. Spread the faces of the driven pulley by threading in
a cap screw; then when the faces are separated, insert
the belt and push down between the faces.

Make sure the splines extend beyond the drive face and
washer or a false torque reading and spline damage
may occur.

GZ065A

PR386

9. Slide the fixed drive face onto the clutch shaft.

CAUTION

11. Place the V-belt into position on the driven pulley
and over the front shaft.

NOTE: At this point, the cap screw can be removed
from between the driven pulley faces.

13. Rotate the V-belt and drive/driven assemblies until
the V-belt is flush with the top of the driven pulley.
14. Place the V-belt cover gasket into position; then
install the cover and secure with the cap screws.
Tighten the cap screws to 8 ft-lb.

Center Crankcase
Components
GZ085

NOTE: The arrows on the V-belt should point forward.

12. Pinch the V-belt together near its center and slide the
spacer and movable drive face onto the shaft. Secure
the drive face with a flat washer and a nut (threads
coated with red Loctite #271). Tighten the nut to 165
ft-lb.

3-80

www.mymowerparts.com

NOTE: This procedure cannot be done with the
engine/transmission in the frame. Complete Removing procedures for Top-Side, Left-Side, and
Right-Side must precede this procedure.
NOTE: For efficiency, it is preferable to remove and
disassemble only those components which need to
be addressed and to service only those components.
The technician should use discretion and sound
judgment.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Separating Crankcase
Halves
1. Remove the oil strainer cap; then remove the oil
strainer.

GZ448A

GZ445

GZ269A

NOTE: Do not disassemble these assemblies
unless service is required. If disassembled, secondary gear sets will have to be reset for backlash and
gear contact (see Servicing Center Crankcase Components in this section).

GZ446

2. Remove the cap screws securing the lower crankcase
to the upper crankcase halves; then using a rubber
hammer, free the lower crankcase and remove.
Account for two alignment pins.

4. Remove one cap screw from the right-side crankcase
and eight cap screws from the left-side crankcase;
then using a rubber mallet, separate the crankcase
halves leaving all components in the right-side case.
Account for a thrust washer on the crankshaft and
flat washers on gear shift shaft, countershaft, and
reverse idler. Note the location of two alignment
pins.

GZ447

3. Remove the secondary drive assembly; then remove
the secondary driven shaft assembly and set aside.
Account for one locating ring.

www.mymowerparts.com

GZ454A

3-81

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ272B

Disassembling Crankcase
Half

GZ299A

3. Remove the snap ring securing the water pump idler
shaft (C) in the crankcase; then remove the shaft and
bearings.

NOTE: For steps 1-8, refer to illustration GZ474A.

GZ463A

4. Remove the snap ring securing the oil pump driven
gear (D) to the oil pump driveshaft; then remove the
gear. Account for a drive pin and washer.
GZ474A

NOTE: To aid in installing, it is recommended that
the assemblies are kept together and IN ORDER.

1. Support the right-side crankcase assembly on suitable support blocks; then carefully remove the crankshaft assembly (A) from the crankcase.

GZ463B

5. Remove the shift fork shaft (E); then remove the gear
shift shaft assembly (F). Account for a washer and a
spacer.

GZ298

2. Remove the snap ring securing the water pump drive
idler (B) to the idler shaft; then remove the drive
idler.

3-82

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
8. Remove the reverse idler gear (I), shaft bushing, and
two washers.

DE677A

GZ279

NOTE: Do not disassemble the countershaft assembly unless necessary. If necessary, see Servicing
Center Crankcase Components sub-section.

Servicing Center
Crankcase Components
GZ276

6. Remove two cap screws securing the oil pump in the
crankcase and remove the oil pump.

NOTE: Whenever a part is worn excessively,
cracked, damaged in any way, or out of tolerance,
replacement is necessary.

SECONDARY OUTPUT DRIVE GEARS
Initial Set-Up
NOTE: If the secondary output driven shaft is
replaced or disassembled, the initial set-up must be
performed to establish correct gear tooth contact. If
only the secondary output driveshaft or secondary
output driven gear are replaced, proceed to Correcting Backlash in this sub-section.

GZ305

7. Remove the driveshaft (G); then remove the countershaft assembly (with shift forks) (H). Account for
two flat washers on the countershaft.

1. Install a new bearing (A) onto the secondary driven
shaft (B) making sure the bearing locating groove is
directed away from the driven gear splines.

MT011A

GZ280B

www.mymowerparts.com

2. Using a suitable press, install the driven gear (C) on
the shaft until the gear firmly seats on the shoulder of
the shaft.
3-83

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

MT011B

3. If installing the existing shaft, start with the shims
removed during disassembly or if installing a new
shaft, start with approximately 1.0 mm shims at point
(D); then install the output driveshaft bearing (E)
making sure the locating pin is directed toward the
center of the shaft.

MT008B

NOTE: Do not use a new lock nut at this time as this
procedure may have to be repeated.

5. Place the assembled shaft into the left crankshaft
case; then lightly coat the gear teeth with machinist’s
lay-out dye. Rotate the shafts through several rotations in both directions. Gear contact should extend
from the root to the top of the gear teeth.

MT012

MT016A

6. To adjust tooth contact, use the following chart to
correctly shim the driven shaft.
Tooth Contact

Shim Correction

Contact at Top

Increase Shim Thickness

Contact at Root

Decrease Shim Thickness

7. After correct tooth contact is established, proceed to
Checking Backlash in this sub-section.
Checking Backlash
MT008A

4. Install a new seal (F), output yoke (G), and nut (H)
and tighten to 74 ft-lb.

1. Install the drive bevel gear assembly and driven
bevel gear/output shaft assembly into the crankcase
bottom cover.
2. Mount the dial indicator so the tip is contacting a
tooth on the secondary drive bevel gear.

3-84

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: Continue to remove, measure, and install
until backlash measurement is within tolerance. Note
the following chart.
Backlash Measurement

Shim Correction

Under 0.127 mm (0.005 in.)

Decrease Shim Thickness

At 0.127-0.381 mm (0.005-0.015 in.)

No Correction Required

Over 0.381 mm (0.015 in.)

Increase Shim Thickness

3. Once correct gear pattern and backlash are established, install a new lock nut on the output shaft yoke
and tighten to 59 ft-lb. Peen the lock nut to the shaft.
GZ396

3. Firmly hold the bearings down and while rocking the
drive bevel gear back and forth, note the maximum
backlash reading on the gauge.

3
MT007A

4. Using an appropriate holding fixture and wrench
adapter, install the secondary drive gear nut and
tighten to 74 ft-lb. The output drive assembly is now
ready for installation.
GZ398

4. Acceptable backlash range is 0.127-0.381 mm
(0.005-0.015 in.).
Correcting Backlash
NOTE: If backlash measurement is within the
acceptable range, no correction is necessary.

1. If backlash measurement is less than specified,
remove an existing shim, measure it, and install a
new thinner shim.

GZ393B

OIL PUMP ASSEMBLY
Disassembling and Inspecting
1. Remove the oil pump cover; then remove the gerotor
set, shaft, and pin (see Disassembling Crankcase
Half in this section).

GZ393A

2. Inspect the crankcase for scoring, discoloration, or
cracks in the gerotor bore. If scored, crankcase
assembly must be replaced.

2. If backlash measurement is more than specified,
remove an existing shim, measure it, and install a
thicker shim.

www.mymowerparts.com

3-85

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ357

3. Inspect the gerotor set for scoring, discoloration, or
cracks; then using a feeler gauge, check the inner to
outer rotor clearance. If measurements exceed specifications, the gerotor set must be replaced.

GZ354A

6. Remove the oil seal from the oil pump cover.

GZ365

Assembling
GZ355

4. Inspect the oil pump cover for scoring, discoloration,
or cracks. Replace if damaged.

1. Install a new oil seal into the oil pump cover; then
coat the lips of the seal with grease and install the
pump driveshaft from the seal side.

GZ358

5. Inspect the oil pump driveshaft and drive pin for
excessive wear or grooving. Replace as required.

3-86

www.mymowerparts.com

GZ359

2. Noting the reference dots on the gerotor set, separate
the inner rotor from the outer rotor and with the reference dot directed toward the oil pump cover, place
the rotor on the shaft; then install the drive pin and
push the shaft into the rotor.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
CRANKSHAFT ASSEMBLY
NOTE: The crankshaft and connecting rod is a
non-serviceable assembly. If any component is out
of specification, the assembly must be replaced.

Measuring Connecting Rod
(Small End Inside Diameter)
1. Insert a snap gauge into the upper connecting rod
small end bore; then remove the gauge and measure
it with micrometer.
GZ356

3
CC290D
GZ363

3. With the outer rotor reference dot directed toward the
oil pump cover, install the rotor onto the inner rotor.

2. Maximum diameter must not exceed specifications.
Measuring Connecting Rod
(Small End Deflection)
1. Place the crankshaft on a set of V blocks and mount a
dial indicator and base on the surface plate. Position
the indicator contact point against the center of the
connecting rod small end journal.
2. Zero the indicator and push the small end of the connecting rod away from the dial indicator.
3. Maximum deflection must not exceed specifications.
Measuring Connecting Rod
(Big End Side-to-Side)

GZ360

4. Place a new O-ring seal on the outside of the oil
pump cover. The oil pump assembly is now ready for
assembly into the crankcase.

1. Push the lower end of the connecting rod to one side
of the crankshaft journal.
2. Using a feeler gauge, measure the gap between the
connecting rod and crankshaft journal.
3. Acceptable gap range must be within specifications.

GZ362
GZ491

www.mymowerparts.com

3-87

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Measuring Crankshaft (Runout)

COUNTERSHAFT

1. Place the crankshaft on a set of V blocks.
2. Mount a dial indicator and base on the surface plate.
Position the indicator contact at point 1 of the crankshaft.

GZ281A

CAUTION
GZ489A

3. Zero the indicator and rotate the crankshaft slowly.

CAUTION
Care should be taken to support the connecting rod
when rotating the crankshaft.

4. Maximum runout must not exceed specifications.
NOTE: Proceed to check runout on the other end of
the crankshaft by positioning the indicator contact at
point 2 and following steps 3-4.

When disassembling the countershaft, care must be
taken to note the direction each major component (dog,
gear) faces. If a major component is installed facing the
wrong direction, transmission damage may occur
and/or the transmission will malfunction. In either case,
complete disassembly and assembly will be required.

Disassembling
1. Remove the shift forks noting the positions for
assembling; then remove the high driven gear outer
washer, high driven gear, high driven gear bearing,
high driven gear bushing, and high driven gear inner
washer.

Measuring Crankshaft
(Web-to-Web)
1. Using a calipers, measure the distance from the outside edge of one web to the outside edge of the other
web.

GZ283A

2. Remove the drive gear; then remove the snap ring
securing the reverse driven gear dog and bushing to
the countershaft.
GZ492

2. Acceptable width range must be within specifications.

GZ296

3-88

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ319

GZ312

3. Remove the reverse driven gear dog.

3
GZ318A
GZ313A

4. Remove the snap ring securing the reverse driven
gear and washer; then remove the washer and gear.

6. Remove the low driven gear. Account for a bearing,
bushing, and thrust washer.

GZ316
GZ314

5. Remove the reverse driven washer; then remove the
low driven gear locking washer.

Assembling
1. From the drive gear end, install a thrust washer,
bushing, and bearing; then install the low driven gear
and washer.

GZ320
GZ317A

www.mymowerparts.com

3-89

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ318

GZ287

2. Install the low driven gear locking washer; then
install the inner reverse driven gear washer.

4. Install the outer reverse driven washer; then secure
the reverse driven gear assembly with a snap ring.

GZ319B

GZ288A

GZ320B

GZ314

3. Install the reverse driven bushing and bearing; then
install the reverse driven gear.

5. Install the reverse driven gear dog onto the countershaft and secure with a snap ring.

GZ286A

GZ313A

3-90

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ312

GZ347

6. From the opposite end of the countershaft, install the
high/low driven gear dog (A), thrust washer (B),
bushing (C), bearing (D), high/low driven gear (E),
and spacer washer (F).

3. Install the countershaft into the crankcase and secure
with the snap ring (flat side away from the bearing).

GZ463A
GZ283B

7. Install the drive gear washer and the shift forks. The
countershaft is now ready for installation.

4. Install the countershaft gear onto the countershaft and
secure with a snap ring (flat-side away from the gear).

Assembling Crankcase
Half
1. Install the oil pump gerotor assembly and oil pump
cover in the crankcase and secure with two cap
screws. Coat the threads with blue Loctite #243 and
tighten securely to 8 ft-lb.
GZ299A

5. Using rubber bands to support the connecting rods, carefully install the crankshaft assembly into the crankcase.

GZ305

2. Install a flat washer, drive pin, and drive gear onto
the oil pump shaft; then secure with a snap ring
(flat-side away from the gear).
GZ474

www.mymowerparts.com

3-91

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: It will be necessary to rotate the crankshaft
back and forth to engage the teeth of the oil pump
and countershaft gears.

6. Install the driveshaft; then with a flat washer on each
end of the reverse idler assembly, install into the
crankcase.

GZ335

8. Place the larger flat washer on the drive gear end of the
countershaft and the smaller flat washer on the high
driven gear end; then with shift forks and shift fork shaft,
install the countershaft assembly into the crankcase.

GZ332

GZ280B

GZ333

7. Install the gear shift shaft into the crankcase making
sure the flat washer is in place on the right case end
and the spacer bearing assembly on the gear shift
stop end.

GZ336

9. Engage the shift forks into the gear shift shaft and
push the shift fork shaft into the crankcase.

DE677A

GZ339

3-92

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

AT THIS POINT
Proper transmission shifting should be verified by turning the gear shift shaft to select High, Low, Neutral, and
Reverse while rotating the input shaft and observing the
countershaft rotation.

AT THIS POINT
The right-side crankcase is now ready for installation to
the left-side crankcase. Proceed to Joining Crankcase
Halves.
GZ345A

Joining Crankcase Halves
1. Using rubber bands, support the connecting rods to
align with the cylinder bores.

4. Carefully join the crankcase halves by placing the
left-side crankcase onto the assembled right side.
Secure with the cap screws (eight left side and one
right side).

GZ342
GZ340

2. Coat both sides with engine oil; then install the
spacer washer on the crankshaft with the radius
directed toward the crankshaft.

5. Tighten the 6 mm cap screws to 8 ft-lb and the 8 mm
cap screws to 20 ft-lb using the pattern shown and
turning the shafts frequently to ensure there is no
binding.
NOTE: Rotate the shafts back and forth to ensure
no binding or sticking occurs.

GZ341

3. Install the two alignment pins; then apply a thin bead
of silicone sealant to the crankcase mating surface.

GZ457A

NOTE: Cap screw number eight (8) is installed from
the right side.
NOTE: If the secondary drive/driven assemblies
have been disassembled, refer to Servicing Center
Crankcase Components for proper gear tooth contact
and backlash.

www.mymowerparts.com

3-93

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
6. Install the locating ring in the crankcase assembly;
then install the secondary driven shaft assembly and
secondary drive assembly making sure the locating
ring and bearing engage correctly.

GZ451

GZ269A

9. Carefully place the lower crankcase cover onto the
joined crankcase halves; then secure with the cap
screws. Tighten the 6 mm cap screws to 8 ft-lb and
the 8 mm cap screws to 20 ft-lb.

GZ448A

7. Make sure the locating pins on the front and rear
bearings are correctly seated in the crankcase.
8. Install two alignment pins into the upper crankcase
assembly; then apply a thin bead of silicone sealant
to the lower crankcase cover.

GZ447

10. Install the oil strainer; then apply a thin bead of silicone sealant to the oil strainer cap and secure with
the cap screws. Tighten to 8 ft-lb.

AT THIS POINT
After completing center crankcase components, proceed to Installing Right-Side Components, to Installing
Left-Side Components, and to Installing Top-Side Components.

Installing
Engine/Transmission
NOTE: Arctic Cat recommends that new gaskets
and O-rings be installed whenever servicing the ATV.
GZ452A

3-94

www.mymowerparts.com

1. Turn the front driveline to place the output drive
yoke universal joint in the horizontal plane; then
secure the driveshaft to the right and against the
engine.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ117A

GZ064A

2. Install the engine/transmission into the frame from
the right side.

8. Install the ignition coils and tighten the cap screws to
7 ft-lb; then connect the primary wires, grounds, and
spark plug caps.

3. Rotate the driveshaft 90°; then lift the front of the
engine sufficiently to engage the splined shaft into
the front differential. Lower the front of the engine.

9. Connect the stator coil connector and crankshaft
position sensor connector; then connect the gear
position switch connector.

GZ110A
GZ069A

GZ119

4. Align the rear output drive flange and the rear yoke
flange and install the cap screws. Tighten to 20 ft-lb.
5. Align the engine with the mounting brackets and
install the through-bolts with flat washers; then
install the flange nuts and tighten to 45 ft-lb.

GZ493A

10. Install the front the rear exhaust pipes with new grafoil seals and tighten the retaining nuts to 20 ft-lb;
then install the muffler and connect all exhaust juncture springs.

6. Connect the coolant hose and tighten the clamps
securely.
7. Secure the engine and harness grounds to the engine
and tighten the cap screw to 8 ft-lb.

www.mymowerparts.com

3-95

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ099A

GZ090B

12. Connect the fuel injector, TPS connector (A), MAP
sensor connector (B), and ISC valve connector (C).

GZ372

11. Install the intake manifolds and tighten to 8 ft-lb;
then install the throttle body and secure with the hose
clamps.

GZ094A

13. Install the shift linkage with bushings and secure
with E-clips.
14. Connect the gasline hose connectors to the fuel rails;
then install any nylon ties that were removed during
disassembly.

GZ106

GZ124

15. Install the air filter housing and secure to the throttle
body with a hose clamp; then connect the IAT sensor
connector.

GZ107

3-96

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
16. Install the V-belt cooling duct and boots. Tighten
securely.
17. Install the front body panel, footrests, foot wells, and
front rack; then install the upper bumper support-to-frame cap screws (see Section 8).
18. Connect the negative battery cable; then secure the
battery with the tool tray and install the seat.
19. Pour in the proper quantities of engine/transmission
oil and coolant; then start the engine and warm up to
operating temperature.
GZ013

20. Check for fluid leaks; then shut off engine and check
fluid levels (see Section 2).

www.mymowerparts.com

3-97

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

SECTION 4 FUEL/LUBRICATION/COOLING

TABLE OF
CONTENTS
Fuel/Lubrication/Cooling ......................................... 4-2
Electronic Fuel Injection .......................................... 4-2
Throttle Cable Free-Play ......................................... 4-4
Engine RPM (Idle)................................................... 4-5
Gas Tank ................................................................. 4-5
Oil Filter/Oil Pump ................................................... 4-5
Testing Oil Pump Pressure...................................... 4-5
Oil Cooler (1000) ..................................................... 4-6
Liquid Cooling System ............................................ 4-6
Electric Fuel Pump/Fuel Level Sensor .................. 4-10
Troubleshooting ..................................................... 4-11

www.mymowerparts.com

4-1

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
REMOVING (450)

Fuel/Lubrication/Cooling
NOTE: Arctic Cat recommends the use of new gaskets, lock nuts, and seals and lubricating all internal
components when servicing the engine/transmission.
NOTE: Some photographs and illustrations used in
this section are used for clarity purposes only and
are not designed to depict actual conditions.
NOTE: Critical torque specifications are located in
Section 1.

SPECIAL TOOLS
A number of special tools must be available to the technician when performing service procedures in this section.
Refer to the current Special Tools Catalog for the appropriate tool description.
Description

p/n

Oil Pressure Test Kit

0644-495

Seal Removal Tool

0644-072

Tachometer

0644-275

1. Turn the ignition switch to the OFF position; then
remove the ignition switch key.

! WARNING
Do not turn the ignition switch to the ON position with
the hoses removed. Gasoline will be pumped by the
electric fuel pump causing a safety hazard.

2. Remove the seat; then disconnect the battery.
3. Remove the storage compartment cover and air filter
housing cover; then remove the air filter.
4. Loosen the clamp securing the air filter housing boot
to the throttle body inlet; then remove the boot from
the throttle body.
5. Slowly disconnect the gasline hose connector from
the fuel rail.

! WARNING
Gasoline may be under pressure. Place an absorbent
towel under the connector to absorb any gasoline spray
when disconnecting.

NOTE: Special tools are available from the Arctic
Cat Service Department.

Electronic Fuel Injection
! WARNING
Whenever any maintenance or inspection is performed
on the fuel system during which there may be fuel leakage, there should be no welding, smoking, open flames,
etc., in the area.

TROUBLESHOOTING
1. Verify that the electric fuel pump is operating by listening for a “whirring” sound for several seconds
after the ignition switch is turned to the ON position.
If no sound can be heard, see Electric Fuel
Pump/Fuel Level Sensor in this section.

FI092A

6. Remove the screw securing the throttle actuator
cover to the throttle body; then remove the cover.
7. Remove the throttle cable from the actuator arm.
8. Loosen the outer jam nut securing the throttle cable to
the throttle body; then route the cable out of the way.
9. Remove the MAP sensor (A), fuel injector connector
(B), ISC connector (C), and TPS connector (D).

2. Check for a flashing DTC (Diagnostic Trouble
Code) on the LCD. If a code is flashing, see appropriate Diagnostic Trouble Codes (DTC) in Section 5.
3. Make sure there is sufficient, clean gas in the gas
tank.
4. Verify that the battery is sufficiently charged to crank
the engine over at normal speed.
5. Check the air filter housing and air filter for contamination. Clean or replace as necessary (see Section 2).

HDX136A

4-2

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
10. Remove the cap screws securing the intake pipe to
the cylinder head and remove the throttle body
assembly; then remove the intake pipe from the
throttle body. Account for an O-ring.

GZ091A

3. Loosen the clamp on the throttle body intake boot;
then remove the air filter housing from the ATV.
FI104A

11. Use tape to cover and seal the intake opening.

4. Disconnect the three wiring connectors from the sensors on the throttle body; then remove the cap screws
securing the throttle body to the intake manifold.

CAUTION
Any objects or liquid entering the intake opening will
fall into the engine causing severe damage if the engine
is turned over or started.

REMOVING (1000)

! WARNING
Whenever the gasline hoses are removed (other than for
pressure testing), the battery must be disconnected to
prevent inadvertent activation of the electronic fuel
pump.

1. Remove the front rack and body panel (see Section
8).

GZ094B

2. Disconnect the wires from the IAT sensor; then
loosen the clamp and remove the inlet air boot from
the air filter housing.

GZ381A

5. Remove the throttle arm cover and disconnect the
throttle cable; then remove the throttle body from the
ATV.
GZ379

www.mymowerparts.com

4-3

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ383A

GZ094B

6. Use tape to cover and seal the intake opening.

CAUTION
Any objects or liquid entering the intake opening will
fall into the engine causing severe damage if the engine
is turned over or started.

INSTALLING (450)
1. Install the throttle body into the intake pipe and
secure with the clamp. Tighten securely.
2. Place a new O-ring in the intake pipe; then position
the pipe onto the engine and secure with two cap
screws.
3. Connect the throttle cable to the throttle body and
adjust throttle cable free-play (see Throttle Cable
Fre-Play in this section); then connect the gasline hose.
4. Connect the four electrical connectors to the throttle
body components.

GZ091A

3. Connect the wiring connector to the IAT sensor.
4. Install the front rack and body panel (see Section 8).
5. Install the seat making sure it locks securely in place.

5. Install the air filter housing boot and secure with the
clamp; then install the air filter, air filter cover, storage compartment, and storage compartment cover.

Throttle Cable Free-Play

6. Connect the battery (positive cable first); then install
the seat making sure it locks securely in place.

To adjust the throttle cable free-play, follow this procedure.

INSTALLING (1000)
1. Connect the throttle cable to the throttle body; then
remove the tape from the intake manifold and install
the throttle body using a new O-ring. Tighten the
cap screws securely.

1. Slide the rubber boot away; then loosen the jam nut
from the throttle cable adjuster.

AL611D

2. Turn the adjuster until the throttle cable has proper
free-play of 3-6 mm (1/8-1/4 in.) at the lever.
GZ381A

2. Connect the three wiring connectors to the sensors;
then install the air filter housing and connect all
hoses. Tighten all clamps securely.
4-4

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
CLEANING AND INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Clean all gas tank components with parts-cleaning
solvent.
2. Inspect all hoses for cracks or leaks.
3. Inspect tank cap and tank for leaks, holes, and damaged threads.
ATV-0047

3. Tighten the jam nut against the throttle cable adjuster
securely; then slide the rubber boot over the adjuster.

Engine RPM (Idle)

4. Remove the fuel level sensor/fuel pick-up assembly
and inspect the fuel level sensor and fuel screen.
NOTE: If the fuel level sensor has failed or may be
faulty, see Electric Fuel Pump/Fuel Level Sensor in
this section.

INSTALLING
1. Install the fuel level sensor/fuel pick-up assembly.

NOTE: The idle RPM is not adjustable on the EFI
models.

2. Place the gas tank into position in the frame; then
install the cap screws. Tighten securely.
3. Connect the gasline hose from the throttle body; then
connect the fuel gauge connector.

Gas Tank

4. Fill the gas tank with gasoline.
5. Start the engine and inspect for leakage.

! WARNING
Whenever any maintenance or inspection is made on
the fuel system during which there may be fuel leakage,
there should be no welding, smoking, open flames, etc.,
in the area.

REMOVING
1. Remove the seat.
2. Remove the rear rack and fenders (see Section 8).
3. Disconnect the hose from the fuel pump to the throttle body by compressing the release on the connector.

6. Install the rear fenders and rack (see Section 8); then
install the seat making sure it latches securely.

Oil Filter/Oil Pump
NOTE: Whenever internal engine components wear
excessively or break and whenever oil is contaminated, the oil pump should be replaced. The oil pump
is not a serviceable component.

Testing Oil Pump
Pressure
NOTE: The engine must be warmed up to the specified temperature for this test.

1. Connect the Tachometer to the engine or utilize the
LCD (if equipped).

FI092A

2. Connect the Oil Pressure Test Kit to the oil pressure
test port (450 models) or the oil cooler to oil filter
line (1000 models).

4. Remove the cap screws securing the gas tank to the
frame.
5. Disconnect the fuel gauge connector; then remove
the gas tank.

www.mymowerparts.com

4-5

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
450

Oil Cooler (1000)
REMOVING
NOTE: It is not necessary to drain the engine oil for
this procedure.

1. Remove the input and output hoses from the fittings
on the cooler.

CAUTION

KC370A

Elevate and secure the hoses to avoid oil spillage.

1000

2. Remove the cap screws securing the oil cooler to the
frame. Account for grommets.
3. Remove the oil cooler from the frame.
INSTALLING
1. Place the cooler into position in the frame.
2. Secure the cooler to the frame with the cap screws
and grommets.

GZ118A

1000

3. Install the hoses onto their respective fittings and
secure with the clamps.

Liquid Cooling System
When filling the cooling system, use premixed Arctic Cat
Antifreeze. While the cooling system is being filled, air
pockets may develop; therefore, run the engine for five
minutes after the initial fill, shut the engine off, and then
fill the cooling system to the bottom of the stand pipe in
the radiator neck.

CAUTION
GZ388A

NOTE: Some oil seepage may occur when installing
the oil pressure gauge. Wipe up oil residue with a
cloth.

3. Start the engine and run at 3000 RPM. With the oil
temperature at 60° C (140° F), the oil pressure gauge
must read as specified.
450

0.6-0.7 kg/cm2 (8.5-10 psi)

1000

1.05-1.2 kg/cm2 (15-17 psi)

NOTE: If the oil pressure is lower than specified,
check for low oil level, defective oil pump, or
restricted oil cooler (1000 models).
NOTE: If the oil pressure is higher than specified,
check for too heavy engine oil weight (see Section 1),
clogged oil passage, clogged oil filter, or improper
installation of the oil filter.

After operating the ATV for the initial 5-10 minutes, stop
the engine, allow the engine to cool down, and check
the coolant level. Add coolant as necessary.

RADIATOR
Removing
1. Drain the coolant at the engine.
2. Remove the front rack (see Section 8).
3. Remove the front bumper and front fender panel (see
Section 8).
4. Remove the upper and lower coolant hoses.
5. Remove the cap screws and nuts securing the radiator to the frame.
6. Disconnect the fan wiring from the main wiring harness; then remove the radiator/fan assembly and
account for the grommets and collars.
7. Remove the fan/fan shroud assembly from the radiator.

4-6

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
THERMOSTAT
Removing (450)

1. Drain approximately one quart of coolant from the
cooling system.
2. Remove the two cap screws securing the thermostat
housing to the cylinder head. Account for an O-ring
and a thermostat.
Removing (1000)

CC863

NOTE: The thermostat is located in a housing
in-line with the upper radiator hoses under the air filter housing.

Cleaning and Inspecting
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Flush the radiator with water to remove any contaminants.
2. Inspect the radiator for leaks and damage.
3. Inspect all hoses for cracks and deterioration.

4. Inspect all fasteners and grommets for damage or
wear.
GZ036A

Installing
1. Position the fan/fan shroud assembly on the radiator;
then secure with existing hardware.
2. Place the radiator with grommets and collars into
position on the frame; then install the cap screws and
nuts. Tighten securely.
3. Install the upper and lower coolant hoses; then
secure with hose clamps.

1. Drain approximately one quart of coolant from the
cooling system.
2. Remove the machine screws securing the thermostat
housing together. Remove the thermostat and
account for an O-ring.
Inspecting
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Inspect the thermostat for corrosion or spring damage.
2. Using the following procedure, inspect the thermostat for proper operation.

A. Suspend the thermostat in a container filled with
water.
B. Heat the water and monitor the temperature
with a thermometer.
AF734D

4. Install the front bumper and front fender panel (see
Section 8).
5. Install the front rack (see Section 8).
6. Fill the cooling system with the recommended
amount of antifreeze. Check for leakage.
7. Connect the fan wiring to the main wiring harness.

www.mymowerparts.com

C. The thermostat should start to open at 71-86° C
(160-187° F).
D. If the thermostat does not open, it must be
replaced.
3. Inspect all coolant hoses, connections, and clamps
for deterioration, cracks, and wear.
NOTE: All coolant hoses and clamps should be
replaced every four years or 4000 miles.

4-7

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Installing (450)
1. Place the thermostat and O-ring into the thermostat
housing; then secure the thermostat housing to the
cylinder head with the two cap screws.

5. Using an impact driver, loosen but do not remove the
two Phillips-head cover screws.

2. Fill the cooling system with the recommended
amount of antifreeze. Check for leakage.
Installing (1000)
1. Place the thermostat and O-ring into the thermostat
housing; then secure the thermostat housing together
with the machine screws.
2. Fill the cooling system with the recommended
amount of antifreeze. Check for leakage.
COOLING FAN

CC785A

6. Remove the two cap screws securing the water pump
to the engine; then remove the water pump.

Removing
1. Remove the radiator (see Radiator in this sub-section).
2. Remove the fan assembly from the radiator.
Installing
1. Position the fan assembly on the radiator; then secure
with existing hardware.
NOTE: The fan wiring must be in the upper-right
position.

2. Install the radiator.
WATER PUMP (450)

CC786A

NOTE: The water pump is a non-serviceable component. It must be replaced as an assembly.

Removing
1. Remove the radiator cap; then remove the water
pump drain and drain the coolant.

Installing
1. Secure the water pump to the engine with the two
cap screws tightened securely; then tighten the two
Phillips-head cover screws securely.

CC786A
CC789

2. Drain the oil from the engine/transmission.
3. Remove the four torx-head cap screws securing the
front and rear fenders to the footrest; then remove the
four cap screws securing the footrest to the frame.
Remove the footrest.
4. Loosen the hose clamps and slide the clamps away
from the hose ends approximately 2 in.; then remove
both hoses from the water pump.
4-8

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: Always use a large container and have sufficient floor drying material available when draining
the coolant in case of coolant spillage.

2. Remove the coolant hoses from the water pump; then
remove two cap screws securing the water pump to
the crankcase.

CC785A

2. Connect the two coolant hoses to the water pump and
secure with the clamps. Tighten securely.
3. Place the footrest into position on the frame and
loosely secure with four cap screws; then secure the
front and rear fenders to the footrest with the four
torx-head cap screws. Tighten the four torx-head cap
screws securely; then tighten the 8 mm cap screws to
20 ft-lb and the 10 mm cap screws to 40 ft-lb.
4. Fill the engine/transmission with the proper amount
of recommended oil.
5. Fill the cooling system with the proper amount of
recommended coolant.

GZ230A

3. Remove the water pump from the engine.
Installing
1. Install a new O-ring onto the water pump and lightly
coat with clean engine oil.

NOTE: While the cooling system is being filled, air
pockets may develop; therefore, run the engine for
five minutes after the initial fill, shut the engine off,
and then fill the cooling system.

6. Check the entire cooling system for leakage.

CAUTION
After operating the ATV for the initial 5-10 minutes, stop
the engine, allow the engine to cool down, and check
the coolant level. Add coolant as necessary.

WATER PUMP (1000)

GZ252C

NOTE: The water pump is a non-serviceable component. It must be replaced as an assembly.

2. Install the water pump assembly onto the engine
aligning the flat drive on the water pump to the slot
in the driveshaft.

Removing
1. Remove the coolant drain plug; then remove the
radiator cap and drain the coolant into a suitable container.

GZ252D

CAUTION
Do not force the water pump housing into the crankcase
or severe engine damage may occur.
GZ093A

www.mymowerparts.com

4-9

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
3. Secure the water pump with the two cap screws and
tighten securely; then connect the coolant hoses and
secure with hose clamps.

3. Turn the ignition switch to the ON position. The fuel
pressure should build until the pump shuts off. Pressure should read 3.0 kg-cm2 (43 psi).

4. Install and tighten the coolant drain plug securely;
then fill the cooling system with the proper amount
of recommended coolant and install the radiator cap.

4. If the pump is not running, disconnect the fuel
pump/tank sensor connector by reaching under the
rear rack from behind.

5. Start the engine and check for coolant leaks; then add
coolant if necessary to proper level.

5. Connect a multimeter to the power supply leads with
the red tester lead to the red wire and the black tester
lead to the black wire; then turn the ignition switch to
the ON position. The meter should read battery voltage. If battery voltage is indicated and the fuel pump
does not run, replace the pump assembly. If no battery voltage is indicated, check the ECU and the
vehicle tilt sensor.

CAUTION
After operating the ATV for the initial 5-10 minutes, stop
the engine, allow the engine to cool down, and check
the coolant level. Add coolant as necessary.

REMOVING

Electric Fuel Pump/Fuel
Level Sensor
The electric fuel pump and fuel level sensor are not serviceable components. If either component fails, it must
be replaced.
TESTING

! WARNING
Whenever any maintenance or inspection is made on
the fuel system during which there may be fuel leakage,
there should be no welding, smoking, open flames, etc.,
in the area.

AT THIS POINT
Prior to removing the electric fuel pump, the following
check should be performed to determine that removal
is necessary.

1. Remove the rear rack and fenders (see Section 8);
then disconnect the power supply/fuel hose connector.
2. Remove the spring clamp; then remove the fuel hose.
3. Remove the screws securing the fuel pump to the gas
tank; then make a reference mark on the fuel pump
and tank.
4. Lift out the fuel pump assembly carefully tilting it
forward to clear the voltage regulator; then guide the
pump and float lever through the opening in the gas
tank.

CAUTION
Take care not to damage the float or float arm or
replacement of the entire assembly will be necessary.

5. Using duct tape or other suitable means, cover the
fuel pump opening.
INSPECTING

1. Turn the ignition switch ON and listen for a momentary “whirring” sound of the pump building pressure.
If the sound is heard (10 seconds), no electrical
checks are necessary. Turn the ignition switch OFF.

If the pump has failed earlier test and must be
replaced, proceed to INSTALLING.

2. Disconnect the gasline hose from the throttle body;
then install a suitable pressure gauge.

1. Inspect the fuel screen and blow clean with low pressure compressed air.

! WARNING
Gasoline may be under pressure. Place an absorbent
towel under the connector to absorb any gasoline spray
when disconnecting.

FI092A

4-10

www.mymowerparts.com

AT THIS POINT

2. Move the float lever and check for free movement.
The float assembly should return to the lower position without force. If not, replace the fuel pump
assembly.
3. Test the fuel level sensor by connecting a multimeter
(A) to the fuel level sensor leads (B); then select
OHMS. The multimeter should show 5 ohms at full
fuel position (C) and 95 ohms at empty fuel position
(D).

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
INSTALLING
1. Mark the new fuel pump with a reference mark in the
same location as the removed pump; then place the
new gasket on the pump.
2. Remove the material covering the fuel pump opening; then carefully guide the fuel pump into position
taking care not to damage the float or float lever.

ATV2116

NOTE: If readings are erratic, clean the resistor
wiper and resistor with clean alcohol and retest. If
still not correct, replace the fuel level sensor.

4. To replace the fuel level sensor, use the following
procedure.

A. Disconnect the two-wire connector (A); then
press the fuel level sensor toward the top of the
fuel pump to release it from the mounting slot
(B).

KX190

3. Rotate the fuel pump until the match marks align;
then install the mounting screws and tighten securely
using a crisscross pattern.
NOTE: It is important to install the fuel pump with
the correct orientation to ensure adequate float lever
clearance.

4. Connect the wires, fuel hose, and spring clamp; then
turn the ignition switch to the ON position. Note that
the fuel pump runs momentarily and the fuel gauge
indicates the proper fuel level.
5. With the transmission in neutral and brake lever lock
engaged, start the engine and check for normal operation. Check for any fuel leaks.
FI460A

B. Engage the tabs (C) of the fuel level sensor into
the mounting slot (B) and press toward the bottom of the fuel pump to latch in place; then connect the two-wire connector (A).

6. Install any wire ties that were removed; then install
the rear fenders, rack, and seat making sure the seat
locks securely.

Troubleshooting
Problem: Starting impaired
Condition
1. Gas contaminated

Problem: Idling or low speed impaired
Condition
1. TPS out of adjustment

Problem: Medium or high speed impaired
Condition
1. High RPM “cut out” against RPM limiter

www.mymowerparts.com

Remedy
1. Drain gas tank and fill with clean gas

Remedy
1. Adjust TPS

Remedy
1. Decrease RPM speed

4-11

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

SECTION 5 ELECTRICAL SYSTEM

TABLE OF
CONTENTS
Electrical System..................................................... 5-2
Electrical Connections............................................. 5-2
Battery..................................................................... 5-2
RPM Limiter............................................................. 5-3
Testing Electrical Components ................................ 5-3
Accessory Receptacle/Connector ........................... 5-3
Brakelight Switch (Auxiliary).................................... 5-3
Brakelight Switch (Handlebar Control) .................... 5-4
Engine Coolant Temperature (ECT) Sensor............ 5-5
Fan Motor ................................................................ 5-5
Power Distribution Module (PDM) ........................... 5-5
Ignition Coil ............................................................. 5-6
EFI Sensors/Components ....................................... 5-7
Speed Sensor ......................................................... 5-8
Electronic Power Steering (EPS)............................. 5-8
Ignition Switch ....................................................... 5-10
Handlebar Control Switches.................................. 5-10
Drive Select Switch ............................................... 5-11
Front Drive/Differential Lock Actuator.................... 5-12
Stator Coil/Crankshaft Position (CKP) Sensor........ 5-12
Starter Relay ......................................................... 5-13
Starter Motor ......................................................... 5-13
Electronic Control Unit (ECU)................................ 5-14
Regulator/Rectifier................................................. 5-14
Headlights ............................................................. 5-14
Taillight - Brakelight ............................................... 5-15
Ignition Timing ....................................................... 5-15
Tilt Sensor ............................................................. 5-15
Throttle Position Sensor (TPS) (450) .................. 5-16
Throttle Position Sensor (TPS) (1000 FIS)............ 5-18
Throttle Position Sensor (TPS)
(1000 TRV/1000 Cruiser/1000 Mud Pro) ........... 5-20
Diagnostic Trouble Codes (DTC) (1000 FIS)......... 5-22
Diagnostic Trouble Codes (DTC)
(450/1000 TRV/1000 Cruiser/1000 Mud Pro)........ 5-22
Troubleshooting ..................................................... 5-24

www.mymowerparts.com

5-1

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Maintenance Charging

Electrical System
This section has been organized into sub-sections which
show procedures for the complete servicing of the Arctic
Cat ATV electrical system.

NOTE: Arctic Cat recommends the use of the CTEK
Multi US 800 or the CTEK Multi US 3300 for battery
maintenance charging. Maintenance charging is
required on all batteries not used for more than two
weeks or as required by battery drain.

NOTE: Some photographs and illustrations used in
this section are used for clarity purposes only and
are not designed to depict actual conditions.

SPECIAL TOOLS
A number of special tools must be available to the technician when performing service procedures in this section.
Refer to the current Special Tool Catalog for the appropriate tool description.
Description
Diagnostic Harness
Fluke Model 77 Multimeter
MaxiClips
Peak Voltage Reading Adapter
Tachometer
Test Plug/Code List
Timing Light

p/n
0486-219
0644-559
0744-041
0644-307
0644-275
0444-216
0644-296

NOTE: Special tools are available from the Arctic
Cat Service Department.

Electrical Connections
The electrical connections should be checked periodically for proper function. In case of an electrical failure,
check fuses, connections (for tightness, corrosion, damage), and/or bulbs.

Battery
After being in service, batteries require regular cleaning
and recharging in order to deliver peak performance and
maximum service life. The following procedure is recommended for cleaning and maintaining a sealed battery.
Always read and follow instructions provided with battery chargers and battery products.
NOTE: Refer to all warnings and cautions provided
with the battery or battery maintainer/charger.

Loss of battery charge may be caused by ambient temperature, ignition OFF current draw, corroded terminals, self
discharge, frequent start/stops, and short engine run
times. Frequent winch usage, snowplowing, extended
low RPM operation, short trips, and high amperage
accessory usage are also reasons for battery discharge.

5-2

www.mymowerparts.com

800E

1. When charging a battery in the vehicle, be sure the
ignition switch is in the OFF position.
2. Clean the battery terminals with a solution of baking
soda and water.
NOTE: The sealing strip should NOT be removed
and NO fluid should be added.

3. Be sure the charger and battery are in a well-ventilated area. Be sure the charger is unplugged from the
110-volt electrical outlet.
4. Connect the red terminal lead from the charger to the
positive terminal of the battery; then connect the
black terminal lead of the charger to the negative terminal of the battery.
NOTE: Optional battery charging adapters are available from your authorized Arctic Cat dealer to connect directly to your vehicle from the recommended
chargers to simplify the maintenance charging process. Check with your authorized Arctic Cat dealer
for proper installation of these charging adapter connectors.

5. Plug the battery charger into a 110-volt electrical
outlet.
6. If using the CTEK Multi US 800, there are no further
buttons to push. If using the CTEK Multi US 3300,
press the Mode button (A) at the left of the charger
until the Maintenance Charge Icon (B) at the bottom
illuminates. The Normal Charge Indicator (C) should
illuminate on the upper portion of the battery charger.
NOTE: The maintainer/charger will charge the battery to 95% capacity at which time the Maintenance
Charge Indicator (D) will illuminate and the maintainer/charger will change to pulse/float maintenance. If the battery falls below 12.9 DC volts, the
charger will automatically start again at the first step
of the charge sequence.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

RPM Limiter
NOTE: The ATV is equipped with an ECU that
retards ignition timing when maximum RPM is
approached. When the RPM limiter is activated, it
could be misinterpreted as a high-speed misfire.

3300A

NOTE: Not using a battery charger with the proper
float maintenance will damage the battery if connected over extended periods.

Charging
NOTE: Arctic Cat recommends the use of the CTEK
Multi US 800 or the CTEK Multi US 3300 for battery
maintenance charging.

1. Be sure the battery and terminals have been cleaned
with a baking soda and water solution.
NOTE: The sealing strip should NOT be removed
and NO fluid should be added.

2. Be sure the charger and battery are in a well-ventilated area. Be sure the charger is unplugged from the
110-volt electrical outlet.
3. Connect the red terminal lead from the charger to the
positive terminal of the battery; then connect the
black terminal lead of the charger to the negative terminal of the battery.
4. Plug the charger into a 110-volt electrical outlet.
5. By pushing the Mode button (A) on the left side of
the charger, select the Normal Charge Icon (E). The
Normal Charge Indicator (C) should illuminate on
the upper left portion of the charger.
6. The battery will charge to 95% of its capacity at
which time the Maintenance Charge Indicator (D)
will illuminate.
NOTE: For optimal charge and performance, leave
the charger connected to the battery for a minimum 1
hour after the Maintenance Charge Indicator (D) illuminates. If the battery becomes hot to the touch, stop
charging. Resume after it has cooled.

7. Once the battery has reached full charge, unplug the
charger from the 110-volt electrical outlet.
NOTE: If, after charging, the battery does not perform
to operator expectations, bring the battery to an authorized Arctic Cat dealer for further troubleshooting.

Testing Electrical
Components
All of the electrical tests should be made using the Fluke
Model 77 Multimeter and when testing peak voltage, the
Peak Voltage Reading Adapter must be used. If any other
type of meter is used, readings may vary due to internal
circuitry. When troubleshooting a specific component,
always verify first that the fuse(s) are good, that the
bulb(s) are good, that the connections are clean and tight,
that the battery is fully charged, and that all appropriate
switches are activated.
NOTE: For absolute accuracy, all tests should be
made at room temperature of 68° F.

Accessory
Receptacle/Connector
NOTE: This test procedure is for either the receptacle or the connector.

VOLTAGE

1. Turn the ignition switch to the ON position; then
set the meter selector to the DC Voltage position.
2. Connect the red tester lead to the red/white wire or
the positive connector; then connect the black tester lead to ground.
3. The meter must show battery voltage.
NOTE: If the meter shows no battery voltage, troubleshoot the battery, fuse, receptacle, connector, or
the main wiring harness.

Brakelight Switch
(Auxiliary)
The switch connector is the two-prong connector on the
brake switch lead above the gas tank on the right side.
NOTE: The ignition switch must be in the ON position.

www.mymowerparts.com

5-3

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
VOLTAGE (Wiring Harness Side)

NOTE: The ignition switch must be in the ON position.

1. Set the meter selector to the DC Voltage position.
2. Connect the red tester to the orange wire; then
connect the black tester lead to the red/blue wire.

VOLTAGE
(Wiring Harness Connector)

1. Set the meter selector to the DC Voltage position.
2. Connect the red tester lead to the orange wire; then
connect the black tester lead to the red/blue wire.

FI510

3. The meter must show battery voltage.
NOTE: If the meter shows no battery voltage, troubleshoot the battery, fuse, switch, or the main wiring harness.
NOTE: If the meter shows battery voltage, the main
wiring harness is good; proceed to test the
switch/component, the connector, and the switch wiring harness for resistance.

RESISTANCE (Switch Connector)

1. Set the meter selector to the OHMS position.
2. Connect the red tester lead to one black wire; then
connect the black tester lead to the other black wire.

FI489

RESISTANCE (Switch Connector)
NOTE: The brake lever must be compressed for this
test. Also, the ignition switch must be in the OFF position.

1. Set the meter selector to the OHMS position.
2. Connect the red tester lead to one black wire; then
connect the black tester lead to the other black wire.

FI502

3. When the brake pedal is depressed, the meter must
show less than 1 ohm.
NOTE: If the meter shows more than 1 ohm of resistance, replace the switch.

Brakelight Switch
(Handlebar Control)
To access the connector, remove the access panel.
5-4

www.mymowerparts.com

FI490

3. When the lever is compressed, the meter must
show less than 1 ohm.
NOTE: If the meter shows more than 1 ohm of resistance, replace the switch.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Engine Coolant
Temperature (ECT)
Sensor
1. Connect the meter leads (selector in OHMS position) to the sensor terminals.
2. Suspend the sensor and a thermometer in a container of cooking oil; then heat the oil.
NOTE: Neither the sensor nor the thermometer
should be allowed to touch the bottom of the container or inaccurate readings will occur. Use wire
holders to suspend the sensor and thermometer.

! WARNING
Wear insulated gloves and safety glasses. Heated oil can
cause severe burns.

3. On the ECT sensor when the temperature reaches
20° C (68° F), the meter should read approximately 2.45k ohms.
4. On the ECT sensor when the temperature reaches
50° C (122° F), the meter should read approximately 800 ohms.
5. On the ECT sensor when the temperature reaches
80° C (176° F), the meter should read approximately 318 ohms.
6. On the ECT sensor when the temperature reaches
110° C (230° F), the meter should read approximately 142 ohms.
7. If the readings are not as indicated, the sensor
must be replaced.
8. Install the sensor and tighten securely.
9. Connect the leads.

Fan Motor

FI501A

3. The meter must show less than 1 ohm.
NOTE: If the meter shows more than 1 ohm of resistance, troubleshoot or replace the fan motor.
NOTE: To determine if the fan motor is good, connect the red wire from the fan connector to the positive side of a 12 volt battery; then connect the black
wire from the fan connector to the negative side. The
fan should operate.

! WARNING
Care should be taken to keep clear of the fan blades.

Power Distribution
Module (PDM)

The fuses are located in a power distribution module
under the seat. If there is any type of electrical system
failure, always check the fuses first.
NOTE: The ignition switch must be in the LIGHTS
position.

1. Remove all fuses from the distribution module.
2. Set the meter selector to the DC Voltage position.
3. Connect the black tester lead to ground.
4. Using the red tester lead, contact each end of the
fuse holder connector terminals individually.

The connector is the black two-prong one located above
the oil cooler/radiator.

5. The meter must show battery voltage from one
side of the connector terminal ends.

NOTE: The ignition switch must be in the ON position.

NOTE: Battery voltage will be indicated from only
one side of the fuse holder connector terminal; the
other side will show no voltage.

RESISTANCE (Fan Motor Connector)

1. Set the meter selector to the OHMS position.
2. Connect the red tester lead to the blue wire; then
connect the black tester lead to the black wire.

NOTE: When testing the HI fuse holder, the headlight dimmer switch must be in the HI position; when
testing the LIGHTS fuse holder, the headlight dimmer
switch can be in either position.
NOTE: If the meter shows no battery voltage, troubleshoot the battery, switches, distribution module,
or the main wiring harness.

www.mymowerparts.com

5-5

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
FUSES
NOTE: To remove a fuse, compress the locking tabs
on either side of the fuse case and lift out.

NOTE: Make sure the fuses are returned to their
proper position according to amperage. Refer to the
fuse block decal for fuse placement.

RELAYS
450/450 TRV

The 4-pin relays are identical plug-in type. Relay function can be checked by switching relay positions. The
relays are interchangeable.
NOTE: The module and wiring harness are not a serviceable components and must be replaced as an assembly.

2411-090

Ignition Coil

1000 Cruiser

NOTE: On the 1000 models, the following procedures should be performed on both ignition coils.

The ignition coil is on the frame above the engine. To access
the coil, the side panel must be removed (see Section 8).
RESISTANCE
2411-081

CAUTION
Always disconnect the battery when performing resistance tests to avoid damaging the multimeter.

1000 Mud Pro

NOTE: For these tests, the meter selector should be
set to the OHMS position and the primary wire(s)
should be disconnected.

Primary Winding
2411-091

1000 Cruiser PS

1. Connect the red tester lead to either terminal; then
connect the black tester lead to the other terminal.
2. The meter reading must be within specification.
Secondary Winding

1. Remove the plug cap from the high tension lead; then
connect the red tester lead to the high tension lead.
2. Connect the black tester lead to either primary
connector.
2411-214

CAUTION
Always replace a blown fuse with a fuse of the same
type and rating.

CAUTION
Always disconnect the battery when performing resistance tests to avoid damaging the multimeter.

1. Set the meter selector to the OHMS position.
2. Connect the red tester lead to one spade end of the
fuse; then connect the black tester lead to the other
spade end.
3. The meter must show less than 1 ohm resistance.
If the meter reads open, replace the fuse.

5-6

www.mymowerparts.com

3. The meter reading must be within specification.
NOTE: If the meter does not show as specified,
replace ignition coil.

Spark Plug Cap

1. Connect the red tester lead to one end of the cap;
then connect the black tester lead to the other end
of the cap.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: If the meter does not read as specified,
replace the sensor.

INLET AIR TEMPERATURE (IAT)
SENSOR (1000 Models)

1. Connect the meter leads (selector in OHMS position) to the sensor terminals.
2. Suspend the sensor and a thermometer in a container of cooking oil; then heat the oil.

AR603D

2. The meter reading must be within specification.
NOTE: If the meter does not read as specified,
replace the spark plug cap.

Primary Voltage - ECU (1000)
NOTE: The ECU is located beneath the rear body
panel near the taillight.

1. Set the meter selector to the DC Voltage position; then
disconnect the orange primary wire from the coil.
2. Connect the red tester lead to the orange primary
wire; then connect the black tester lead to ground.
3. Turn the ignition switch to the ON position.
4. The meter reading must show battery voltage.

EFI Sensors/Components
CRANKSHAFT POSITION (CKP)
SENSOR
To test the CKP sensor, see Stator Coil/Crankshaft Position (CKP) Sensor in this section.
MANIFOLD ABSOLUTE PRESSURE
(MAP) SENSOR (1000 Models)

1. Disconnect the MAP connector from the pressure
sensor located on top of the throttle body.
2. Select DC Voltage on the tester and turn the ignition switch to the ON position.
3. Connect the black tester lead to the black/green
wire and the red tester lead to the orange/blue
wire. The meter should read 4.5-5.5 DC volts. If
the meter does not read as specified, check the
ECU connector or wiring.
4. Connect the MAP to the harness; then using MaxiClips, connect the red tester lead to the brown/white
wire and the black tester lead to the black/green
wire. With the engine running at idle speed, the
meter should read approximately 1.5 DC volts.

www.mymowerparts.com

NOTE: Neither the sensor nor the thermometer
should be allowed to touch the bottom of the container or inaccurate readings will occur. Use wire
holders to suspend the sensor and thermometer.

! WARNING
Wear insulated gloves and safety glasses. Heated oil can
cause severe burns.

3. On the sensor when the temperature reaches 20° C
(68° F), the meter should read approximately
2.45k ohms.
4. On the sensor when the temperature reaches 50° C
(122° F), the meter should read approximately 800
ohms.
5. On the sensor when the temperature reaches 80° C
(176° F), the meter should read approximately 318
ohms.
6. On the sensor when the temperature reaches 110°
C (230° F), the meter should read approximately
142 ohms.
7. If the readings are not as indicated, the sensor
must be replaced.
MANIFOLD ABSOLUTE PRESSURE/
INLET AIR TEMPERATURE (MAP/IAT)
SENSOR (450)

1. Disconnect the MAP/IAT connector from the sensor located on top of the throttle body.
2. Select DC Voltage on the tester and turn the ignition switch to the ON position.
3. Connect the black tester lead to the black/pink
wire and the red tester lead to the orange/blue
wire. The meter should read 4.5-5.5 DC volts. If
the meter does not read as specified, check the
ECU connector or wiring.
4. Connect the MAP/IAT to the harness; then using
MaxiClips, connect the red tester lead to the
brown/white wire and the black tester lead to the
black/pink wire. With the engine running at idle
speed, the meter should read approximately 2.5
DC volts (MAP sensor signal).
5. Connect the red tester lead to the green/red wire.
With the engine at idle and at room temperature
(approximately 60° F), the meter should read
approximately 2.9 DC volts.
5-7

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: If the meter does not read as specified,
replace the sensor.

Speed Sensor
NOTE: Prior to testing the speed sensor, inspect the
three-wire connector on the speed sensor for contamination, broken pins, and/or corrosion.

1. Set the meter selector to the DC Voltage position.
2. With appropriate needle adapters on the meter
leads, connect the red tester lead to the voltage
lead (V); then connect the black tester lead to the
ground lead (G).

CD071

Electronic Power
Steering (EPS)
NOTE: Certain models have been produced with
electronic power steering. The following information
is intended to be used when servicing these models.

CD885A

3. Turn the ignition switch to the ON position.
4. The meter must show 6-12 DC volts.
5. Leave the black tester lead connected; then connect the red tester lead to the signal lead (S) pin.
6. Slowly move the ATV forward or backward; the
meter must show 0 and 6-12 DC volts alternately.
NOTE: If the sensor tests are within specifications,
the gauge must be replaced (see Section 8).

To replace a speed sensor, use the following procedure.

1. Disconnect the three-wire connector from the
speed sensor harness or from the speed sensor;
then remove the Allen-head cap screw securing
the sensor to the sensor housing.
2. Remove the sensor from the sensor housing
accounting for an O-ring.
3. Install the new speed sensor into the housing with
new O-ring lightly coated with multi-purpose
grease; then secure the sensor with the Allen-head
cap screw (threads coated with blue Loctite #242).
Tighten securely.

The electronic power steering (EPS) system is an electro-mechanical device that utilizes 12 volt DC power to
drive a motor linked to the steering shaft to assist the
rider when rotating the handlebar. Rider steering inputs
are detected by a torque-sensing transducer assembly
within the EPS housing. These inputs are converted to
electronic signals by the transducer and control circuitry
to tell the motor which way to drive the steering shaft.
When no steering input (pressure on the handlebar) is
detected, no torque signal is generated, and no steering
assist is provided by the motor.
The EPS system is battery-system powered; therefore,
the battery must be in good condition and fully charged.
Power delivery and overload protection are provided by
an EPS relay and 30-amp fuse, located under the seat in
the Power Distribution Module (PDM).
If a system malfunction occurs, a malfunction code
“P0635” will be displayed on the LCD gauge. Initially,
the gauge will go blank for 30 seconds and the code will
flash: then the gauge will return to normal except the
code will continue to be displayed.
The following is a list of conditions that can generate a
malfunction code. All conditions with the exception of
item 5 are external to the EPS assembly and therefore can
be cleared without replacement of the EPS assembly.
Make sure to thoroughly troubleshoot the entire system
before replacing the EPS assembly.
NOTE: The EPS assembly is not serviceable and no
service parts or parts lists are available. The EPS is
only serviceable as an assembly and must not be disassembled or EPS warranty will be voided.

CAUTION
Do not attempt to check resistance of the EPS motor
(2-pin input receptacle). There are internal capacitors
holding a charge that can cause internal damage to an
ohmmeter.

5-8

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Malfunction code P0635 will appear if one of the following six conditions occur:
1. Battery system power failure:
A. 30 amp EPS fuse blown
B. EPS relay failure
C. EPS voltage less than 8.5 DC volts for more than
two seconds
2. Ignition switch ON for more than five minutes with
the engine not running.
3. Vehicle Speed Signal Malfunction (engine speed
must exceed 2700 RPM for more than 60 seconds to
generate a malfunction code - timer resets if engine
drops below 2700 RPM).
A. Diode defective (open or shorted)
B. Diode not installed
C. Diode installed in reverse
D. Speed sensor defective
E. Speed sensor signal erratic
F. Speed sensor signal present but without tachometer signal
G. Speed sensor power from LCD gauge interrupted
H. Incorrect LCD gauge installed
4. Engine Speed Signal Malfunction (vehicle speed must
exceed 5 MPH for more than two seconds - timer
resets if speed drops below 5 MPH.
A. No engine speed signal
B. Erratic engine speed signal
5. EPS Control Circuit Malfunction
6. Engine Stop Switch in Stop position with Ignition
Key switch ON.
The following procedures may be helpful in determining
the source of a malfunction code:
Condition: Ignition Key Switch ON and NO EPS assist
when moving the handlebar. Code “P0635” flashing.
NOTE: Prior to troubleshooting below, make sure
that Ignition Key Switch has not been left on with the
engine not started. After five minutes, this will deactivate the EPS and display the malfunction code. Turn
Ignition Key Switch OFF and back to ON to reset and
reactivate the EPS. If code and symptom persists,
continue as follows:

1. Check 30 amp EPS fuse.
2. Check EPS relay (may be switched with any other
4-pin relay on PDM - replace relay if EPS normal
after switching).

www.mymowerparts.com

3. Disconnect 2-pin connector on the EPS assembly
and connect a volt meter set to DC voltage to the harness (black meter lead to BLK and red meter lead to
ORG/BRN) With the ignition switch to the ON position, the meter must read more than 8.5 DC volts (if
correct voltage is not present, check connections and
wiring harness - if correct voltage is present, replace
EPS assembly - see Section 8 - Steering Post/Tie
Rods sub-section).

CAUTION
Do not attempt to disassemble the EPS assembly as
there are no serviceable components within the assembly and damage will occur voiding the EPS warranty.

Condition: Ignition switch ON and EPS assist normal
when moving handlebar. Code “P0635” flashing.
NOTE: Prior to troubleshooting steps below, make
sure that the Engine Stop Switch has not been used
to stop the engine leaving the ignition switch in the
ON position. If the engine stop switch is not in the
RUN position, set to RUN position and cycle the ignition switch to OFF then ON. If malfunction code is
still indicated, proceed as follows.

1. Check for speed sensor signal by disconnecting the
8-pin connector from the EPS assembly and using a
multi-meter set to the DC volt position, connect the
black lead to the PNK/YEL wire and the red lead to
the ORG wire. With the ignition switch turned to the
ON position, slowly move the vehicle forward or
backward. The meter must alternate from 0 DC volts
to approximately 12 DC volts. If meter readings are
not as specified:
A. Check EPS diode for correct installation or open
diode (replace diode or install correctly).
B. Check speed sensor using procedure found in this
section (replace speed sensor/install proper
gauge).
2. Check for engine speed signal by disconnecting the
8-pin connector from the EPS assembly and using a
multi-meter set to the AC voltage position, connect
one lead to any BLK wire and the other lead to
YEL/VLT wire. Start the engine and with the engine
idling the meter should read approximately 7.5 AC
volts. If meter reading is not as specified:
A. Check the wiring harness from EPS to gauge
(YEL/VLT wire - repair wiring).
B. Check the AC generator using the Stator
Coil/Crankshaft Position (CKP) Sensor procedure
found in this section. If not to specifications,
replace the stator coil.
If after completing the above checks with normal results
and malfunction code “P0635” persists, the EPS assembly must be replaced. To replace the EPS assembly, see
Section 8 - Steering Post/Tie Rods sub-section.

5-9

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Ignition Switch
The ignition switch harness connects to the switch with a
four-pin connector. To access the connector, remove the
ignition switch nut, remove the switch, and press the connector release tab. Pull the connector from the switch.

CF274A

1. Turn the ignition switch to the ON position.
2. Set the meter selector to the OHMS position.
3. Connect either tester lead to pin C; then connect
the other tester lead to pin D.
4. The meter must show less than 1 ohm.
CF272A

5. Turn the ignition switch to the LIGHTS position.
6. Connect either tester lead to pin A; then connect
the other tester lead to pin B.
7. The meter must show less than 1 ohm.
8. Connect either tester lead to pin C; then connect
the other tester lead to pin D.
9. The meter must show less than 1 ohm.

CF273A

VOLTAGE

10. With the switch in the OFF position, connect the
red tester lead and the black tester lead to each of
the remaining pins. The meter must show an open
circuit on all pins.
NOTE: If the meter shows more than 1 ohm of resistance, replace the switch.

NOTE: Perform this test on the harness connector.

1. Set the meter selector to the DC Voltage position.
2. Connect the red meter lead to either red wire; then
connect the black meter lead to ground.
3. Meter must show battery voltage.
NOTE: If the meter shows no battery voltage, troubleshoot the battery or the main wiring harness.

RESISTANCE
NOTE: Perform this test on the switch using the following procedure.

Handlebar Control
Switches
The connector is the yellow one next to the steering
post. To access the connector, the steering post cover
and the right-side fender splash shield must be
removed (see Section 8).
NOTE: These tests should be made on the top side
of the connector.

RESISTANCE (HI Beam)

1. Set the meter selector to the OHMS position.
2. Connect the red tester lead to the yellow wire; then
connect the black tester lead to the gray wire.
3. With the dimmer switch in the HI position, the
meter must show less than 1 ohm.
5-10

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: If the meter shows more than 1 ohm of resistance, replace the switch.

RESISTANCE (LO Beam)

1. Connect the red tester lead to the white wire; then
connect the black tester lead to the gray wire.

2. Connect the red tester lead to one red/yellow wire;
then connect the black tester wire to the other red/yellow wire. The meter must show less than 1 ohm.
3. Depress and hold the reverse override button. The
meter must show an open circuit.

2. With the dimmer switch in the LO position, the
meter must show an open circuit.

4. Connect the red tester lead to the blue wire; then
connect the black meter lead to the black wire. The
meter must show an open circuit.

NOTE: If the meter reads resistance, replace the
switch.

5. Depress and hold the reverse override button. The
meter must show less than 1 ohm.

DIODE (Starter Button)
NOTE: If voltage is not as specified, check the condition of the battery in the meter prior to replacing the
switch. A low battery will result in a low voltage reading during a diode test.

NOTE: If the meter does not show as specified,
replace the switch.

Drive Select Switch

1. Set the meter selector to the Diode position.
2. Connect the red tester lead to the orange/white
wire; then connect the black tester lead to the yellow/green wire.

The connector is the two-wire black snap-lock one in
front of the steering post. To access the connector, the
cover must be removed.

3. With the starter button depressed, the meter must
show 0.5-0.7 DC volt.

NOTE: Resistance tests should be made with the
connector disconnected and on the selector-side of
the connector.

4. With the starter button released, the meter must
show 0 DC volts.

RESISTANCE

5. Connect the red tester lead to the yellow/green
wire; then connect the black tester lead to the
orange/white wire.

1. Set the meter selector to the OHMS position.
2. Connect the red tester lead to the red wire; then
connect the black tester lead to the white wire.

6. With the starter button depressed, the meter must
show 0 DC volts.

3. With the selector switch in the 2WD position, the
meter must show an open circuit.

NOTE: If the meter does not show as specified,
replace the switch.

4. With the selector switch in the 4WD position, the
meter must show less than 1 ohm.

RESISTANCE (Engine Stop Switch)

1. Set the meter selector to the OHMS position.
2. Connect the red tester lead to the orange wire; then
connect the black tester lead to the orange/white wire.
3. With the switch in the OFF position, the meter
must show an open circuit.

NOTE: If the meter does not show as specified,
replace the drive select switch.

VOLTAGE
NOTE: The battery must be connected when performing voltage tests.

1. Set the meter selector to the DC Voltage position.

4. With the switch in the RUN position, the meter
must show less than 1 ohm.

2. Connect the black tester lead to the negative battery terminal.

NOTE: If the meter shows more than 1 ohm of resistance, replace the switch.

3. Connect the red tester lead to the white wire on the
harness side of the connector.

RESISTANCE (Reverse Override)

4. Turn the ignition switch to the RUN position.

The connector is the four-prong white one next to the
steering post. To access the connector, the front rack and
front fenders must be removed (see Section 8).

5. The meter must show 12 DC volts.

1. Set the meter selector to the OHMS position.

www.mymowerparts.com

NOTE: If the meter shows other than specified,
check the harness, connector, 30 amp fuse, and battery connections.

5-11

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Front Drive/Differential
Lock Actuator
NOTE: With the engine stopped and the ignition
switch in the ON position, a momentary “whirring”
sound must be noticeable each time the drive select
switch is moved to 2WD and 4WD. Test the switch, 30
amp fuse, and wiring connections prior to testing the
actuator.
NOTE: The differential must be in the unlocked
position for this procedure.

VOLTAGE

1. Select the 2WD position on the drive select
switch; then disconnect the connector on the actuator wiring harness.
2. With the ignition switch in the OFF position, connect the black tester lead to the black wire in the
supply harness; then connect the red tester lead to
the orange wire in the supply harness.
3. Turn the ignition switch to the ON position. The
meter must show 12 DC volts.
4. Connect the red tester lead to the white/orange
wire in the supply harness. The meter must show
12 DC volts.

Stator Coil/Crankshaft
Position (CKP) Sensor
VOLTAGE
(AC Generator - Regulated Output)

1. Set the meter selector to the DC Voltage position.
2. Connect the red tester lead to the positive battery
post; then connect the black tester lead to the negative battery post.
3. With the engine running at a constant 5000 RPM
(with the headlights on), the meter must show
14-15.5 DC volts.
CAUTION
Do not run the engine at high RPM for more than 10 seconds.

NOTE: If voltage is lower than specified, test AC
Generator - No Load.

VOLTAGE
(AC Generator - No Load)
The connector is a three-pin one in the harness coming
from the generator.

5. Connect the red tester lead to the white/green wire
in the supply harness. The meter must show 10.2
DC volts.
6. Select the 4WD position on the drive select
switch; then connect the red tester lead to the
white/orange wire in the supply harness. The
meter must show 12 DC volts.
NOTE: The 4WD icon on the LCD should illuminate.

7. Connect the red tester lead to the white/green wire
in the supply harness. The meter must show 0 DC
volts.
8. Select Differential Lock on the drive select switch;
then connect the red tester lead to the white/orange
wire in the supply harness. The meter must show 0
DC volts.
9. Connect the tester lead to the white/green wire in
the supply harness. The meter must show 0 DC
volts.
NOTE: The 4WD and LOCK icons on the LCD
should illuminate.
NOTE: If the voltage readings are as specified and
the actuator does not function correctly, replace the
actuator (see Section 6).

5-12

www.mymowerparts.com

FI083B

NOTE: Test the connector that comes from the
engine.

1. Set the meter selector to the AC Voltage position.
2. Test between the three yellow wires (450) or black
wires (1000) for a total of three tests.
3. With the engine running at a constant 5000 RPM,
all voltage tests must be within specifications.
CAUTION
Do not run the engine at high RPM for more than 10 seconds.

NOTE: If both stator coil tests failed, replace the
stator assembly.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
RESISTANCE (AC Generator)

3. Depress the starter button while observing the
multimeter. The multimeter should drop to 0 volts
and a “click” should be heard from the relay.

1. Set the meter selector to OHMS position.
2. Test between the three yellow wires (450) or gray
wires (1000) for a total of three tests.
3. The meter reading must be within specification.
RESISTANCE
(Crankshaft Position Sensor)

NOTE: If a “click” is heard and more than 1 volt is
indicated by the multimeter, replace the starter relay.
If no “click” is heard and the multimeter continues to
indicate battery voltage, proceed to step 4.

4. Disconnect the two-wire plug from the starter
relay; then connect the red tester lead to the green
wire and the black tester lead to the black wire.

1. Set the meter selector to the OHMS position.
2. Connect the red tester lead to the blue wire; then
connect the black tester lead to the green wire. The
meter reading must be within specification.
AC VOLTAGE
NOTE: The battery must be at full charge for these
tests.

Crankshaft Position Sensor

1. Set the meter selector to the AC Voltage position.
2. Connect the red tester lead to the blue wire; then
connect the black tester lead to the green wire.

KX059A

3. Crank the engine over using the electric starter.

5. Depress the starter button and observe the multimeter.

4. The meter reading must be within specification.

NOTE: If battery voltage is indicated, replace the
starter relay. If no voltage is indicated, proceed to
Power Distribution Module (PDM) check in this section.

Starter Relay
1. Remove the seat; then using the multimeter set to
the DC Voltage position, check the relay as follows.
2. Connect the red tester lead to the positive battery
terminal; then connect the black tester lead to the
starter cable connection on the starter relay. The
meter must show battery voltage.

Starter Motor
NOTE: The starter motor is a non-serviceable component. If the following test does not result as specified, the starter motor must be replaced.

TESTING VOLTAGE
Perform this test on the starter motor positive terminal.
To access the terminal, slide the boot away.
NOTE: The ignition switch must be in the ON position, the engine stop switch in the RUN position, and
the shift lever in the NEUTRAL position.

1. Set the meter selector to the DC Voltage position.
2. Connect the red tester lead to the starter motor terminal; then connect the black tester lead to
ground.
FI496

NOTE: Make sure that the ignition switch is in the ON
position, transmission in neutral, brake lock released,
and the engine stop switch in the RUN position.

www.mymowerparts.com

3. With the starter button depressed, the meter must
show approximately 10.0 DC volts and the starter
motor should operate.

5-13

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
The ECU is rarely the cause for electrical problems; however,
if the ECU is suspected, substitute another ECU of the same
part number to verify the suspected one is defective.
Codes can be cleared by following the procedures located
in the appropriate Diagnostic Trouble Codes (DTC)
sub-section in this section.

Regulator/Rectifier

AR607D

NOTE: If the meter showed correct voltage but the
starter motor did not operate or operated slowly, the
starter motor is defective.
NOTE: If the meter showed no voltage, inspect the
main fuse, ground connections, starter motor lead,
battery voltage (at the battery), starter relay, or the
neutral start relay.

REMOVING

1. Disconnect the battery.
CAUTION
Always disconnect the negative battery cable from the
battery first; then disconnect the positive cable.

2. Remove the nut securing the positive cable to the
starter motor; then remove the cable from the
starter motor.

The regulator/rectifier is located under the rear rack and
rear fenders.
TESTING

1. Start engine and warm up to normal operating
temperature; then connect a multimeter to the battery as follows.
2. Select the DC Voltage position; then connect the
red tester lead to the positive battery post and the
black tester lead to the negative battery post.
3. Start the engine and slowly increase RPM. The
voltage should increase with the engine RPM to a
maximum of 15.5 DC volts.
NOTE: If voltage rises above 15.5 DC volts, the regulator is faulty or a battery connection is loose or corroded. Clean and tighten battery connections or
replace the regulator/rectifier. If voltage does not rise,
see Stator Coil/Crankshaft Position (CKP) Sensor Voltage in this section. If charging coil voltage is normal, replace the regulator/rectifier.

3. Remove the two cap screws securing the starter
motor to the crankcase; then remove the starter
motor. Account for the wiring forms and an
O-ring.
INSTALLING

1. Apply a small amount of grease to the O-ring seal on
the starter motor; then install the starter motor into
the crankcase. Secure with two machine screws and
wiring forms.
2. Secure the positive cable to the starter motor with
the nut.
3. Connect the battery (positive cable first).

Electronic Control Unit
(ECU)
The electronic control unit (ECU) is located beneath the
seat near the battery (450) or under the fender near the
taillight (1000).
NOTE: The ECU is not a serviceable component. If
the unit is defective, it must be replaced.

5-14

www.mymowerparts.com

Headlights
The connectors are the four 2-prong ones plugged into
the headlight bulbs (two on each side).
VOLTAGE
NOTE: Perform this test in turn on the main harness
side of all four connectors. Also, the ignition switch
must be in the LIGHTS position.
NOTE: The LO beam is the outside bulb, and the HI
beam is the inside bulb.

1. Set the meter selector to the DC Voltage position.
2. Connect the red tester lead to one wire; then connect the black tester lead to the other wire.
3. With the dimmer switch in the LO position, test
the two outside connectors (LO beam). The meter
must show battery voltage.
4. With the dimmer switch in the HI position, test the
two inside connectors (HI beam). The meter must
show battery voltage.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: If battery voltage is not shown in any test,
inspect the LIGHTS fuse, battery, main wiring harness, connectors, or the left handlebar switch.

Taillight - Brakelight
The connector is the 3-prong one located under the rear
fender assembly.
VOLTAGE (Taillight)
NOTE: Perform this test on the main harness side of
the connector. Also, the ignition switch should be in
the LIGHTS position.

1. Set the meter selector to the DC Voltage position.
2. Connect the red tester lead to the white wire; then
connect the black tester lead to the black wire.

Tilt Sensor
! WARNING
Incorrect installation of the tilt sensor could cause sudden loss of engine power which could result in loss of
vehicle control resulting in injury or death.

CAUTION
Do not drop the tilt sensor as shock can damage the
internal mechanism.

SUPPLY VOLTAGE

1. Disconnect the three-wire connector from the sensor; then select DC Voltage on the multimeter and
connect the red tester lead to the orange wire (C)
and the black tester lead to the black wire (A).

3. With the ignition key in the LIGHTS position, the
meter must show battery voltage.
NOTE: If the meter shows no voltage, inspect fuses,
wiring harness, connectors, and switches.

VOLTAGE (Brakelight)
NOTE: Perform this test on the main harness side of
the connector. Also, the ignition switch should be in
the ON position and the brake (either foot pedal or
hand lever) must be applied.

1. Set the meter selector to the DC Voltage position.
2. Connect the red tester lead to the red/blue wire; then
connect the black tester lead to the black wire.
3. With either brake applied, the meter must show
battery voltage.
NOTE: If the meter shows no voltage, inspect fuses,
wiring harness, connectors, and switches.

5
CD706A

2. Turn the ignition switch to the ON position. The
multimeter should read battery voltage. If battery
voltage is not indicated, check the 30-amp main
and 10-amp ignition fuses, wiring harness, or the
ignition switch.
3. Remove the red tester lead and connect to the
blue/brown wire (B). The multimeter should read
approximately 2.5 DC volts. If the specified voltage is not indicated, check wire connections at the
ECU or substitute another ECU to verify the test.

Ignition Timing
The ignition timing cannot be adjusted; however, verifying
ignition timing can aid in troubleshooting other components.
To verify ignition timing, use the following procedure.

1. Attach the Timing Light to the spark plug high tension lead; then remove the timing inspection plug
from the left-side crankcase cover.
2. Using the Tachometer, start the engine and run at
1500 RPM; ignition timing should be 10° BTDC.
3. Install the timing inspection plug.

CD706B

If ignition timing cannot be verified, the rotor may be damaged, the key may be sheared, the trigger coil/CKP sensor
bracket may be bent or damaged, or the ECU may be faulty.

www.mymowerparts.com

5-15

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
OUTPUT VOLTAGE
NOTE: Needle adapters or a “break-out” harness
will be required on the multimeter leads as the following tests are made with the sensor connected.

NOTE: When replacing the sensor after testing,
make sure the arrow marking is directed up.

1. Connect the three-wire plug to the sensor; then
remove the right-side mounting screw securing the
sensor to the rear frame.

CD705A

CD707

2. Install the needle adapters to the multimeter leads;
then select DC Voltage on the multimeter.
3. Connect the red tester lead to the blue/brown wire
(B) and the black tester lead to the black/yellow wire
(A); then turn the ignition switch ON and observe the
meter. The meter should read 0.3-1.5 DC volt.

Throttle Position Sensor
(TPS) (450)
INSPECTING

1. Remove the left-side engine cover; then disconnect the three-wire TPS connector plug.

PR544
CD705B

4. Tilt the sensor 60° or more to the left and right
observing the meter. The meter should read 3.0-7.0
DC volts after approximately one second in the
tilted position. If the meter readings are not as
specified, the tilt sensor is defective.

NOTE: Prior to testing the TPS, inspect the
three-wire plug connector on the main harness and
the three-pin plug on the TPS for contamination, broken pins, and/or corrosion.

2. Make sure the ignition switch is in the OFF position; then select the DC Voltage position on the
meter.
3. Connect the black tester lead to terminal B and the
red tester lead to terminal A. Turn the ignition
switch to the ON position. The meter should read
approximately 5.0 DC volts.

CD709

5-16

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

PR538A

NOTE: If the meter does not read as specified,
check for poor connections at the ECU or open/broken wires in the wiring harness.

CAUTION
Always make sure the ignition switch is in the OFF position before disconnecting the ECU.

4. Turn the ignition switch to the OFF position.
5. Select the OHMS position on the meter; then perform the following resistance tests on the TPS.
A. Pin (B) to ground - infinity (open circuit).
B. Pin (A) to pin (B) - approximately 1.22k ohms
(throttle closed).
C. Pin (A) to pin (B) - approximately 4.5k ohms
(throttle full-open).
D. Pin (A) to pin (C) - approximately 5.5k ohms.

PR546A

8. Select the DC Voltage position on the meter and
turn the ignition switch to the ON position. The
meter should read approximately 4.5 DC volts
with the throttle closed and approximately 1.5 DC
volts with the throttle in the full-open position.
NOTE: If the meter readings are as specified, check
the main harness connector at the ECU main harness
wiring. If the meter readings are not as specified,
replace the TPS and adjust to specifications (see
INSTALLING/ADJUSTING in this sub-section).

CAUTION
Always make sure the ignition switch is in the OFF position before disconnecting the ECU.

9. Verify all malfunction codes are closed after servicing is complete (see appropriate Diagnostic
Trouble Codes (DTC) in this section).
REMOVING

1. Remove the left-side engine cover; then disconnect the three-wire TPS connector plug.

PR535A

NOTE: If any meter reading is not as specified,
replace or adjust the TPS (see INSTALLING/ADJUSTING in this sub-section).

6. Connect the positive lead to the battery; then connect the negative lead.
7. Connect the main harness TPS connector to the
TPS; then using MaxiClips, connect the black tester lead to the black/green wire and the red tester
lead to the green/black wire.

www.mymowerparts.com

PR544

2. Remove the screw securing the TPS to the throttle
body and remove the TPS.
INSTALLING/ADJUSTING

1. Place the TPS into position on the throttle body and
secure with the screw. Do not tighten at this time.
2. Connect the TPS Multi-Analyzer Harness connector #8 to the TPS; then connect the harness to the
TPS Analyzer Tool.

5-17

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Throttle Position Sensor
(TPS) (1000 FIS)
INSPECTING

1. Remove the left-side engine cover; then disconnect the three-wire TPS connector plug.

FI672

3. Using a multimeter, connect the black tester lead
to the black socket (GND) on the analyzer and the
red tester lead to the white socket (VAR); then
select the Voltage position.

PR544

NOTE: Prior to testing the TPS, inspect the
three-wire plug connector on the main harness and
the three-pin plug on the TPS for contamination, broken pins, and/or corrosion.

FI673A

4. Adjust the TPS until a reading of 0.68 DC volt is
obtained; then tighten the screw securely. Open
and close the throttle and determine the reading
returns to 0.68 DC volt. Readjust as necessary.

2. Make sure the ignition switch is in the OFF position; then select the DC Voltage position on the
meter.
3. Connect the black tester lead to terminal C and the
red tester lead to terminal B. Turn the ignition
switch to the ON position. The meter should read
approximately 5.0 DC volts.

FI674

5. Disconnect the harness from the analyzer; then
disconnect the harness from the TPS and reconnect the TPS main harness connector.
6. Tighten the mounting screw securely.

PR538A

4. Remove the red tester lead from terminal B and
connect it to terminal A. The meter should read 0
DC volts.
NOTE: If the meter does not read as specified,
check for poor connections at the ECU or open/broken wires in the wiring harness.

CAUTION
Always make sure the ignition switch is in the OFF position before disconnecting the ECU.

5-18

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
5. Turn the ignition switch to the OFF position; then
disconnect the battery (negative cable first).
CAUTION
Always disconnect the battery when performing resistance tests to avoid damaging the multimeter.

6. Select the OHMS position on the meter; then perform the following resistance tests on the TPS.
A. Pin (B) to ground - infinity (open circuit).
B. Pin (A) to pin (B) - approximately 1.22k ohms
(throttle closed).
C. Pin (A) to pin (B) - approximately 4.36k ohms
(throttle full-open).
D. Pin (A) to pin (C) - approximately 4.05k ohms.

PR535A

NOTE: If any meter reading is not as specified,
replace or adjust the TPS (see INSTALLING/ADJUSTING in this sub-section).

NOTE: If the meter readings are as specified, check
the main harness connector at the ECU main harness
wiring. If the meter readings are not as specified,
replace the TPS and adjust to specifications (see
INSTALLING/ADJUSTING in this sub-section).

CAUTION
Always make sure the ignition switch is in the OFF position before disconnecting the ECU.

10. Clear all ECU error codes after servicing is complete (see appropriate Diagnostic Trouble Codes
(DTC) in this section).
REMOVING

1. Remove the left-side engine cover; then disconnect the three-wire TPS connector plug.

PR544

2. Remove the two screws securing the TPS to the
throttle body and remove the TPS.
INSTALLING/ADJUSTING

7. Connect the positive lead to the battery; then connect the negative lead.

1. Place the TPS into position on the throttle body and
secure with the two screws. Do not tighten at this time.

8. Connect the main harness TPS connector to the
TPS; then using MaxiClips, connect the black tester lead to the black/green wire and the red tester
lead to the green/black wire.

2. Connect the main harness to the TPS.
3. Locate the diagnostic connector under the seat
next to the PDM; then install the test plug from
Test Plug/Code List kit onto the connector.
4. Turn the ignition switch to the ON position and
note the position of the TPS indicator icon (A, B,
or C); then adjust the TPS until the TPS icon
appears in the center position (B).

PR546A

9. Select the DC Voltage position on the meter and
turn the ignition switch to the ON position. The
meter should read approximately 0.60 DC volt
with the throttle closed and approximately 4.0 DC
volts with the throttle in the full-open position.

www.mymowerparts.com

PR542A

5-19

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

PR540A

PR544

NOTE: Prior to testing the TPS, inspect the
three-wire plug connector on the main harness
and the three-pin plug on the TPS for contamination, broken pins, and/or corrosion.

2. Make sure the ignition switch is in the OFF position; then select the DC Voltage position on the
meter.
3. Connect the red tester lead to terminal B and the
black tester lead to terminal A. Turn the ignition
switch to the ON position. The meter should read
approximately 5.0 DC volts.
PR541A

5. Tighten the mounting screws securely; then verify
the TPS icon appears in the center position (throttle in idle position).
6. Cycle the throttle lever from idle to approximately
half throttle position several times; then return the
throttle to idle. The display should return to (B)
position.
7. Remove the test plug; then install the left-side
engine cover.

Throttle Position Sensor
(TPS) (1000 TRV/1000
Cruiser/1000 Mud Pro)
INSPECTING
1. Remove the seat, side covers, front rack, and front
body panel (see Section 8); then remove the air filter assembly. Remove the TPS connector plug
from the TPS.

PR538A

NOTE: If the meter does not read as specified,
check for poor connections at the ECU or
open/broken wires in the wiring harness.

CAUTION
Always make sure the ignition switch is in the OFF
position before disconnecting the ECU.

4. Turn the ignition switch to the OFF position.
5. Select the OHMS position on the meter; then perform the following resistance tests on the TPS.
A. Pin (B) to ground - infinity (open circuit).
B. Pin (A) to pin (C) - approximately 1k ohms
(throttle closed).
C. Pin (A) to pin (C) - approximately 5k ohms
(throttle full-open).
D. Pin (A) to pin (B) - approximately 5k ohms.

5-20

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
REMOVING
1. Remove the left-side engine cover; then disconnect the three-wire TPS connector plug.

PR535A

NOTE: If any meter reading is not as specified,
replace or adjust the TPS (see INSTALLING/ADJUSTING in this sub-section).
PR544

2. Remove the screw securing the TPS to the throttle
body and remove the TPS.
INSTALLING/ADJUSTING
1. Place the TPS into position on the throttle body and
secure with the screw. Do not tighten at this time.
2. Connect the TPS Multi-Analyzer Harness connector #8 to the TPS; then connect the harness to the
TPS Analyzer Tool.

PR546A

8. Select the DC Voltage position on the meter and
turn the ignition switch to the ON position. The
meter should read approximately 0.6 DC volt with
the throttle closed and approximately 4.0 DC volts
with the throttle in the full-open position.
NOTE: If the meter readings are as specified,
check the main harness connector at the ECU
main harness wiring. If the meter readings are not
as specified, replace the TPS and adjust to specifications (see INSTALLING/ADJUSTING in this
sub-section).

FI672

3. Using a multimeter, connect the black tester lead
to the white socket (VAR) on the analyzer and the
red tester lead to the red socket (+SV); then select
the DC Voltage position.

CAUTION
Always make sure the ignition switch is in the OFF
position before disconnecting the ECU.

9. Verify all malfunction codes are cleared after servicing is complete (see appropriate Diagnostic
Trouble Codes (DTC) in this section).
FI676A

www.mymowerparts.com

5-21

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
4. Adjust the TPS until a reading of 0.6 DC volt is
obtained; then tighten the screw securely. Open
and close the throttle and determine the reading
returns to 0.6 DC volt. Readjust as necessary.
5. Disconnect the harness from the analyzer; then
disconnect the harness from the TPS and reconnect the TPS main harness connector.

Diagnostic Trouble Codes
(DTC) (1000 FIS)
If a sensor fails or an out-of-tolerance signal is sensed by
the ECU, a code will be generated by the ECU. This will
result in the analog needle swinging full scale (if
equipped) or the LCD gauge going blank (if equipped).
The EFI icon will flash.

To read the code(s), use the following procedure.
1. Make sure the ignition switch is in the OFF position; then remove the seat.

•
•
•
•
•
•
•
•
•
•
•

26 =
32 =
34 =
40 =
41 =
60 =
95 =
96 =
97 =
98 =
99 =

Ignition Coil #2* - H2
Fuel Injector #1*
Fuel Injector #2* - H2
ISC (Idle Speed Control) Valve
Fuel Pump Relay*
Cooling Fan Relay
Sensor Power
Incorrect ECU*
ECU Memory Power (constant battery power)
ECU to Gauge Comm Link - H2
Start/Run Not Possible (active code only)

*Will initiate code 99.

After all active codes are cleared, clear stored code(s)
using the following procedure.
NOTE: The ignition switch should be in the OFF
position.

1. With the diagnostic harness connected to the diagnostic plug and the drive select switch in the 4WD
position, hold the reverse override switch down
and turn the ignition switch to the ON position.

2. Locate the diagnostic plug next to the PDM; then
remove the black rubber cap.

2. After ten seconds, release the reverse override
switch and turn the ignition switch to the OFF position; then turn the ignition switch to the ON position.
The display should read AC00 (no fault detected).

3. Connect the Diagnostic Harness to the diagnostic
plug.

NOTE: If the LCD still displays a code, continue
troubleshooting the appropriate component.

3. Disconnect the diagnostic harness; then install the
black rubber cap.
4. Install the seat making sure it locks securely in place.

Diagnostic Trouble Codes
(DTC) (450/1000
TRV/1000 Cruiser/1000
Mud Pro)
ATV-112

4. Turn the ignition switch to the ON position and
read the code on the LCD. Refer to the following
Code List to identify the specific problem area.
Code List
NOTE: Each of the following numerical codes will
have a two-letter prefix. A prefix of AC (Active Code)
or SC (Stored Code) will be displayed. Always correct
and clear Active Codes before clearing Stored Codes.
•
•
•
•
•
•
•
•
•
•

00 =
12 =
13 =
13 =
14 =
15 =
16 =
21 =
23 =
24 =

5-22

No Fault Detected (active code only)
CKP (Crankshaft Position) Sensor*
APS (Air Pressure Sensor) - H1
MAP (Manifold Absolute Pressure) Sensor - H2
TPS (Throttle Position Sensor)
ECT (Engine Coolant Temperature) Sensor
Speed Sensor
IAT (Inlet Air Temperature) Sensor
Tilt Sensor*
Ignition Coil #1*

www.mymowerparts.com

If an EFI or related chassis component fails or an out-of-tolerance signal is detected by the ECU, a trouble code will be
generated in the ECU and displayed on the LCD. For the first
thirty seconds, the LCD will go blank and the code will be
displayed alternately with a wrench icon or malfunction indicator light (MIL). After thirty seconds, the digital display will
return to normal; however, the MIL and trouble code will continue to flash. On models equipped with the analog gauge, the
needle will swing full-scale for thirty seconds; then return to
normal with the MIL and code continuing to flash.
Code List
NOTE: Each of the following numerical codes will have a
one-letter prefix of C or P. A “C” prefix denotes a chassis
malfunction and a “P” prefix denotes a power train malfunction.
NOTE: Normal malfunction codes are cleared from
the LCD when the component is replaced or the malfunction is corrected; however, intermittent codes
must be cleared as noted in the code chart.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Gauge DTC

Input/
Output
I

Tilt Sensor Circuit High

Tilt Sensor Circuit Low/SG/Open

ON
ON
ON
ON
OFF

F2
F2
F3
F3
F3

I
I
I
I
I

V
V
V
V
V

MAP Sensor Circuit Low/SG/Open
MAP Sensor Circuit High/SP
Intake Air Temp Sensor Circuit Low/SG
Intake Air Temp Sensor Circuit High/Open
Intake Air Temp Sensor Circuit Intermittent

ON
ON
ON
OFF

F4
F4
F4
F4

I
I
I
I

V
V
V
V

Engine Coolant Temp Sensor Circuit Range/Performance
Engine Coolant Temp Sensor Circuit Low/SG
Engine Coolant Temp Sensor Circuit High/Open/SP
Engine Coolant Temp Sensor Circuit Intermittent

G3
G3
G3
N/A
J1
J1
J1

I
I
I
N/A
O
O
O

V
V
V
N/A
L
L
L

Wrench Icon Status

C0063(1)
(1)

C0064
P0107
P0108
P0112
P0113

P0114(1)
P0116
P0117
P0118
P0119(1)
P0121
P0122
P0123
P0219
P0231
P0232

ON
ON
ON

P0233(1)

ECU PIN

High/Low Variable

Description

Throttle Position Sensor Range/Performance
Throttle Position Sensor Circuit Low/SG
Throttle Position Sensor Circuit High
Engine Over-Speed Condition
Fuel Pump Relay Circuit Low/SG/Open
Fuel Pump Relay Circuit High
Fuel Pump Relay Circuit

P0261(2)

(2)

Rear Cylinder Injector Circuit High

P0263(2)

Rear Cylinder Injector Balance/Open

P0264(2)

Front Cylinder Injector Circuit Low/SG - H2

P0265

(2)

Front Cylinder Injector Circuit High - H2

P0266

(2)

Front Cylinder Injector Balance/Open - H2

P0336(1)

D1/E1

Crankshaft Angle Sensor Synchronization

P0337(1)

D1/E1

Crankshaft Angle Sensor Circuit/SG

P0339(1)

D1/E1

Crankshaft Angle Sensor Intermittent/Erratic

P0262

Rear Cylinder Injector Circuit Low/SG

O
O
O
N/A
I/O
I/O
I
I
N/A
O

L
L
L
N/A
V
V
H
H
N/A
L

Fan Relay Control Circuit
Fan Relay Control Circuit High
Fan Relay Control Circuit Low/SG/Open
Vehicle Speed-Sensor
Idle Air Control System Circuit Low/SG
Idle Air Control System Circuit High/Open
System Voltage Low
System Voltage High
ECU Memory Check-Sum Error
Starter Relay Circuit

P2300(2)

ON
Gauge Direct Error-Code
ON

L3
L3
N/A
N/A
A1
A1
N/A
M1

O
O
N/A
N/A
O
O
N/A
O

L
L
N/A
N/A
H
H
N/A
L

Starter Relay Circuit Low
Starter Relay Circuit High
VIN Not Programmed or Incompatible
Power-Steering Controller Circuit
Sensor Power Circuit Low
Sensor Power Circuit High
Traction Controller Circuit
Rear Ignition Coil Primary Circuit Low/SG/Open

P2301(2)

Rear Ignition Coil Primary Circuit High

(2)

Front Ignition Coil Primary Circuit Low/Open - H2

P2304(2)

Front Ignition Coil Primary Circuit High - H2

A4
A4
B1/C1

I
I
I/O
N/A

H
H
H/L
N/A

P0480
P0484
P0485
P0500
P0508
P0509
P0562
P0563
P0601
P0615(1)
P0616
P0617
P0630
P0635
P0642
P0643
P0856

P2303

K2
K2
ON
K2
Gauge Direct Error-Code
N/A
ON
C4/D3/D4/E4
ON
C4/D4
L1
L1
N/A
L3
ON
ON
Gauge Direct Error-Code

P2531
P2532
U0155
“FUEL OFF”

Ignition Switch Circuit Low
Ignition Switch Circuit High
LCD Gauge Communication Lost
Tilt Sensor Activation Operator-Code

Gauge Direct Error-Code
High = Signal Level is too High (Possible Short-to-Battery (+))
Low = Signal Level is too Low (Possible Short-to-Ground or Short-to-Chassis)
SG = Possible Short-to-Ground or Short-to-Chassis
SP = Possible Short-to-Power or Short-to-Battery
Open = Open-Circuit (Possible Broken-Wire or No-Connection)
(1): These codes cleared by one complete power-cycle only (key-off, power-latch, key-on):
C0063, C0064, P0114, P0119, P0233, P0336, P0337, P0339, P0615
(2): These codes cleared by one complete starting-cycle only (key-off, power-latch, key-on, start, key-off, power-latch, key-on):
C0261, P0262, P0263, P0264, P0265, P0266, P2300, P2301, P2303, P2304

www.mymowerparts.com

5-23

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Troubleshooting
Problem: Spark absent or weak
Condition
1.
2.
3.
4.
5.

Ignition coil defective
Spark plug defective
Magneto defective
ECU defective
Pick-up coil defective

Problem: Spark plug fouled with carbon
Condition
1.
2.
3.
4.
5.

Gasoline incorrect
Air cleaner element dirty
Spark plug incorrect (too cold)
Valve seals cracked - missing
Oil rings worn - broken

Problem: Spark plug electrodes overheat or burn
Condition
1. Spark plug incorrect (too hot)
2. Engine overheats
3. Spark plug loose

Problem: Magneto does not charge
Condition
1. Lead wires/connections shorted - loose - open
2. Magneto coils shorted - grounded - open
3. Regulator/rectifier defective

Remedy
1.
2.
3.
4.
5.

Replace ignition coil
Replace plug
Replace stator coil
Replace ECU
Replace stator coil

Remedy
1.
2.
3.
4.
5.

Change to correct gasoline
Clean element
Replace plug
Replace seals
Replace rings

Remedy
1. Replace plug
2. Service cooling system
3. Tighten plug

Remedy
1. Repair - replace - tighten lead wires
2. Replace magneto coils
3. Replace regulator/rectifier

Problem: Magneto charges, but charging rate is below the specification
Condition
Remedy
1.
2.
3.
4.

Lead wires shorted - open - loose (at terminals)
Stator coil (magneto) grounded - open
Regulator/rectifier defective
Cell plates (battery) defective

Problem: Magneto overcharges
Condition
1. Internal battery short circuited
2. Regulator/rectifier resistor damaged - defective
3. Regulator/rectifier poorly grounded

Problem: Charging unstable
Condition
1. Lead wire intermittently shorting
2. Magneto internally shorted
3. Regulator/rectifier defective

Problem: Starter button not effective
Condition
1.
2.
3.
4.
5.

Battery charge low
Switch contacts defective
Starter relay defective
Emergency stop - ignition switch off
Wiring connections loose - disconnected

1.
2.
3.
4.

Repair - tighten lead wires
Replace stator coil
Replace regulator/rectifier
Replace battery

Remedy
1. Replace battery
2. Replace resistor
3. Clean - tighten ground connection

Remedy
1. Replace lead wire
2. Replace stator coil
3. Replace regulator/rectifier

Remedy
1.
2.
3.
4.
5.

Charge - replace battery
Replace switch
Replace relay
Turn on switches
Connect - tighten - repair connections

Problem: Battery “sulfation” (Acidic white powdery substance or spots on surfaces of cell plates)
Condition
Remedy
1. Charging rate too low - too high
2. Battery run-down - damaged
3. Electrolyte contaminated

5-24

www.mymowerparts.com

1. Replace battery
2. Replace battery
3. Replace battery

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Problem: Battery discharges too rapidly
Condition
1.
2.
3.
4.

Charging system not charging
Cell plates overcharged - damaged
Battery short-circuited
Electrolyte contaminated

Problem: Battery polarity reversed
Condition
1. Battery incorrectly connected

Remedy
1.
2.
3.
4.

Check magneto - regulator/rectifier - circuit connections
Replace battery - correct charging system
Replace battery
Replace battery

Remedy
1. Reverse connections - replace battery - repair damage

www.mymowerparts.com

5-25

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

SECTION 6 - DRIVE SYSTEM/
BRAKE SYSTEM

TABLE OF
CONTENTS
Drive System/Brake System.................................... 6-2
Front Drive Actuator/Differential Lock...................... 6-2
Front Differential ...................................................... 6-3
Drive Axles ............................................................ 6-16
Rear Gear Case .................................................... 6-19
Hub........................................................................ 6-22
Hand Brake Lever/Master Cylinder Assembly....... 6-23
Hydraulic Brake Caliper......................................... 6-24
Troubleshooting Drive System............................... 6-28
Troubleshooting Brake System.............................. 6-28

www.mymowerparts.com

6-1

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Drive System/Brake
System

Front Drive
Actuator/Differential
Lock

NOTE: Some photographs and illustrations used in
this section are used for clarity purposes only and
are not designed to depict actual conditions.

NOTE: The actuator is not a serviceable component. If it is defective, it must be replaced.

NOTE: Critical torque specifications are located in
Section 1.

NOTE: The actuator will operate only when the ignition switch is in the ON position.

NOTE: Specifications regarding the gear cases
(capacities, lubricant type, etc.) can be found in Section 1 of this manual.

The front drive actuator is located on the side of the front
drive input housing. With the engine stopped and the
ignition switch in the ON position, a momentary “whirring” sound can be heard each time the drive select
switch is shifted or the differential lock is activated. If no
sound is heard, see Section 5. If the actuator runs constantly or makes squealing or grinding sounds, the actuator must be replaced.

Ring Gear Backlash
Ring Gear End Play

0.28-0.38 mm (0.011-0.015 in.)
0.1-0.2 mm (0.004-0.008 in.)

GENERAL INFORMATION
All gear cases are tagged beneath a cover bolt. This tag is
marked with a production date code, sequence code, and
a ratio code.
A. A “6” or “3.6” on the lower-right corner indicates
a 3.6:1 gear set ratio (10:36 teeth).

REMOVING
1. Disconnect the connector on the actuator harness.
2. Using a T-30 torx wrench, remove the mounting cap
screw from the driveshaft side of the actuator.

B. A “1” or “3.1” on the lower-right corner indicates
a 3.1:1 gear set ratio (11:34 teeth).
The die-cast aluminum housings have been assembled
with thread-rolling screws (trilobular). When assembling
with these screws, start the screws carefully into the
housing; then use the following torque values.
Size

New Housing

Reassembled
Housing

M6 (Torx T-30 Recess)
M8 (Torx T-40 Recess)
M10 (Torx T-50 Recess)

8-9.5 ft-lb
25-31 ft-lb
37-45.5 ft-lb

6.5-9 ft-lb
21-25 ft-lb
31-38 ft-lb

SPECIAL TOOLS

AG926

A number of special tools must be available to the technician when performing service procedures in this section.
Description
Backlash Measuring Tool (24-Spline Axle)
Backlash Measuring Tool (27-Spline Axle)
CV Boot Clamp Tool
Internal Hex Socket
Pinion Gear/Shaft Removal Tool
Gear Case Seal Installer Tool

3. Remove the mounting cap screw from below the
actuator on the suspension side.

p/n
0544-010
0544-011
0444-120
0444-104
0444-127
0444-224

NOTE: Special tools are available from the Arctic
Cat Service Department.
AG927

4. Loosen but do not remove the mounting cap screw at
the front of the actuator; then slide the actuator to the
rear enough to clear the slotted mounting tab and the
selector shaft.

6-2

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

AG928

INSTALLING
NOTE: Make sure to properly align the differential
lock actuator lever with the hole in the differential
lock plunger.

1. Lubricate the O-rings on the actuator; then ensure
that all mounting surfaces are clean and free of
debris.
2. Align the actuator with the selector shaft and slide it
forward onto the shaft taking care to engage the cap
screw in the slot of the front mounting tab.

AG926

NOTE: It is important to tighten this cap screw while
the others are loose to ensure proper seating of the
actuator.

5. Tighten the remaining cap screws; then connect the
electrical plug to the main harness.
6. Turn the ignition switch to the ON position and
check the operation by shifting the drive select
switch several times.
7. Secure the wiring harness to the frame with a nylon
cable tie.

Front Differential
NOTE: To remove the rear gear case, see Rear Gear
Case in this section.

REMOVING DIFFERENTIAL
1. Secure the ATV on a support stand to elevate the
wheels.
AG925

3. While holding the actuator firmly forward, tighten
the front cap screw to hold the actuator in place; then
install but do not tighten the two remaining cap
screws.

! WARNING
Make sure the ATV is solidly supported on the support
stand to avoid injury.

2. Remove the drain plug and drain the gear lubricant
into a drain pan; then reinstall the plug and tighten to
45 in.-lb.

AG928

4. Loosen the front cap screw; then tighten the cap
screw on the driveshaft side.

www.mymowerparts.com

ATV0082A

3. Remove the front wheels.

6-3

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
4. Pump up the hand brake; then engage the brake lever
lock.
5. Remove the cotter pin securing the hex nut; then
remove the hex nut and washer.

AF896D

10. Remove the upper ball joint cap screws taking care
not to strip the threads on the ball joint shaft; then
using a rubber mallet, tap the end of the axle and free
it from the knuckle assembly.
KX041

6. Release the brake lever lock.
NOTE: It is not necessary to remove the brake
hoses from the calipers for this procedure.

7. Remove the two brake calipers. Account for the four
cap screws.

AF628D

11. Pull the steering knuckle away from the axle.

AF894D

8. Remove the tie rod cotter pins and discard the pins.

KX151

12. Support the axle to not allow it to drop or hang.

CAUTION
The axle must be supported. If the axle is allowed to
drop or hang, damage to the inner CV joint may occur.
AF895D

9. Remove the tie rod lock nuts.

6-4

www.mymowerparts.com

13. Remove the lower shock bolts. Account for the lock
nuts; then move the shocks aside and secure them
with a strap.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

AF897D

14. Remove the upper A-arm lock nuts and cap screws;
then remove the A-arms.

PR725A

16. Remove the inner fender panels.
17. Using a T-30 torx wrench, remove the three screws
securing the front drive actuator to the gear case;
then remove the actuator.

AF610D

15. Push the axle shaft firmly toward the differential to
release the internal lock; then while holding the axle
in, pull the CV cup from the differential.

CAUTION

AG925

18. Remove the lower differential mounting cap screw.
Account for a lock nut and washers.

Do not attempt to use a slide hammer or differential/axle
damage will occur.

CD026

19. Remove the upper differential mounting cap screws.
PR729B

www.mymowerparts.com

6-5

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

CD016

GC004A

20. Free the differential assembly from the frame mountings; then shift the differential assembly forward
enough to disengage the front driveshaft from the
output yoke.

2. Using a rubber mallet, remove the housing. Account
for a gasket. Remove the fork, collar, and spring.
Note the location of all the components for assembling purposes.

KX161

GC015

21. Place the differential on its right side; then remove it
from the frame.

CD106

KX159

Disassembling Input Shaft
NOTE: This procedure can be performed on a rear
gear case; however, some components may vary
from model to model. The technician should use discretion and sound judgment.

1. Using a T-40 torx wrench, remove the cap screws
securing the pinion housing.

6-6

www.mymowerparts.com

3. Using a boot-clamp pliers (or suitable substitute),
remove the boot clamps; then remove the boots and
splined drive from the input shaft.
4. Remove the snap ring; then remove the input shaft
from the pinion housing.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

CD107

5. Using a seal removal tool, remove the input shaft
seal. Account for a spacer.

KX219

Assembling Input Shaft
1. Place the pinion housing in a press and install the
input shaft bearing. Secure the bearing with the
existing snap ring making sure the sharp edge of the
snap ring faces to the outside.

GC010

6. Remove the snap ring securing the input shaft bearing; then place the pinion housing in a press and
remove the bearing.
GC012

GC011
GC011

2. Install the input shaft seal making sure it is fully
seated in the housing.

AF984

www.mymowerparts.com

6-7

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GC014

CD099

3. Lubricate the input shaft with High-Performance #2
Molybdenum Disulphide Grease packing the boot
ribs and splines; then assemble allowing excess
grease to freely escape. Slight pressure on the boot
will be present during assembly. Secure with new
clamps.

5. Place the pinion housing with new gasket onto the
gear case housing; then secure with the existing cap
screws. Tighten to 23 ft-lb.
NOTE: If a new gear case housing is being installed,
tighten the cap screws to 25-31 ft-lb.

NOTE: Any time drive splines are separated, clean
all splines with parts-cleaning solvent and dry with
compressed air; then lubricate with recommended
grease.

CD103

Disassembling Differential Assembly

GC009A

4. Install the input shaft into the pinion housing and
secure with the snap ring; then install the front boot
and secure with an appropriate boot clamp and the
rear boot with an appropriate boot clamp.

CD112

6-8

www.mymowerparts.com

NOTE: This procedure can be performed on a rear
gear case.

1. Using a T-40 torx wrench, remove the cap screws
securing the pinion housing. Account for the coupler,
fork, and spring (differential only).

GC015

2. Using a T-40 torx wrench, remove the cap screws
securing the differential cover. Account for and make
note of the ID tag location for assembling purposes.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GC003

KX177

3. Using a plastic mallet, tap lightly to remove the differential cover. Account for an O-ring.

KX178

KX174

6. Place the differential with the open side down; then
lift the housing off the spider assembly. Account for
shim(s) and mark as right-side.

NOTE: If the cover is difficult to remove, pry on
the cover in more than one recessed location.

4. Remove the splined coupler, shifter fork, pin, and
spring of the differential lock assembly and set aside.
Note position of parts for assembling purposes.

KX179

KX175

5. Remove the left differential bearing flange assembly
and account for a shim. Mark the shim as left-side.

KX181

www.mymowerparts.com

6-9

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
Disassembling Pinion Gear
NOTE: Any service of the pinion gear or related
bearings will require a new gear case/differential
housing. The removal of the lock collar severely damages the threads in the housing.

1. Using the 48 mm Internal Hex Socket, remove the
lock collar securing the pinion gear assembly.

CC879

4. Remove any reusable parts from the gear case housing; then discard the housing and lock collar.
Assembling Pinion Gear
1. Install the bearing onto the pinion shaft. Install the
pinion shaft collar.
CC875

CC882

CC876

2. Using the Pinion Gear/Shaft Removal Tool and a
hammer, remove the pinion gear from the gear case
housing.

CC883

2. Place the pinion assembly in a bearing puller; then
install the bearing using a press.

CC878

3. Secure the pinion gear in a bearing puller; then
remove the pinion bearing using a press. Account for
a collar and a bearing.

6-10

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

CC884

3. Coat a new needle bearing and the bearing pocket of
a new gear case/differential housing with red Loctite
#271; then using a suitable driver, install the bearing
lightly seated against the bearing seats. Do not push
the bearing too far into the pocket.

CC891

Shimming Procedure/Shim Selection
Case-side Shims (Backlash)
p/n

in.

0402-405

1.3

0.051

0402-406

1.4

0.055

0402-407

1.5

0.059

0402-408

1.6

0.063

0402-409

1.7

0.067

Cover-side Shims (Ring Gear End-Play)

GC044

4. Install the pinion gear assembly into the housing.
Using the 48 mm Internal Hex Socket, secure the
pinion gear assembly with the existing lock collar.
Tighten to 125 ft-lb.
NOTE: On a front differential, the lock collar has
right-hand threads. On a rear drive gear case, the
lock collar has left-hand threads or a snap-ring.

p/n

in.

1402-074

1.3

0.051

1402-075

1.4

0.055

1402-076

1.5

0.059

1402-077

1.6

0.063

1402-078

1.7

0.067

It is very important to adjust bevel gears for the proper
running tolerances. Gear life and gear noise are greatly
affected by these tolerances; therefore, it is very important to properly adjust any gear set prior to final assembly.
The following procedure can be used on both front differential or rear drive gear case.
NOTE: All bearings must be installed in the gear
case and the pinion properly installed before proceeding.

Backlash
NOTE: Always set backlash prior to any other shimming.

1. Install the existing shim or a 0.051-0.055-in. shim on
the gear case side of the ring gear assembly.
CC890

5. Place a punch on the edge of the lock collar in the oil
gallery area; then using a hammer, stake the lock collar to ensure that the collar will remain securely
tightened.

www.mymowerparts.com

6-11

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GC031A

GC033A

2. Install the ring gear with shim in the gear case; then
while holding the pinion stationary, rock the ring
gear forward and back to determine if any backlash
exists. If no backlash exists, install a thicker shim
and recheck.

4. Install the existing shim or a 0.063 in. shim on the
cover side of the ring gear; then place the assembled
gear case cover onto the gear case and secure with
three cap screws. Tighten evenly using a crisscross
pattern.

GC036A

GC036B

3. Install the bearing flange onto the gear case cover
making sure the alignment/locating pin engages the
locating hole in the cover; then make sure the bearing flange is completely seated in the cover.

5. Place the appropriate Backlash Measuring Tool into
the splines of the ring gear and install a dial indicator
making sure it contacts the gauge at a 90° angle and
on the index mark.

GC032A

GC040

6-12

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
2. Zero the dial indicator; then push the ring gear
toward the dial indicator and release. End-play
should be 0.004-0.008 in.
3. To increase end-play, decrease the shim thickness.
To decrease end-play, increase the shim thickness.
NOTE: Once proper backlash and end play are
established, the gear case can be assembled (see
Assembling Differential Assembly in this sub-section).

GC039A

6. Zero the dial indicator; then while holding the pinion
stationary, rock the ring gear assembly forward and
back and record the backlash. Backlash must be
0.011-0.015 in. If backlash is within specifications,
proceed to Ring Gear End-Play. If backlash is not
within specifications, increase shim thickness to
increase backlash or decrease shim thickness to
decrease backlash.
NOTE: Higher backlash settings usually result in
quieter gear operation.
CC888

Assembling Differential Assembly
1. With the pinion gear and new bearings installed,
place the selected (backlash) shim on the gear case
side of the ring gear with the chamfered side toward
the ring gear; then install into gear case/differential
housing.

6
GC037A

Ring Gear End-Play
After correcting backlash, ring gear end-play can be
adjusted. To adjust end-play, use the following procedure.
1. Secure the gear case in a holding fixture with the
cover side up; then install a dial indicator contacting
the ring gear axle flange.

GC031A

GC020
GC035

www.mymowerparts.com

2. Place the selected (end-play) shim, chamfered side
toward the gear, onto the cover side of the ring gear.
6-13

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GC036B

CF275A

NOTE: The spider and ring gear assembly must be
replaced as a complete unit.

5. Making sure the O-ring is properly positioned on the
differential housing cover assembly, install the cover
with existing cap screws (coated with green Loctite
#609). Account for the ID tag. Tighten the cap
screws evenly to 23 ft-lb.

3. Assemble the fork and sliding collar into the cover
assembly; then install the left bearing flange/bearing
assembly and seat firmly into the cover.

NOTE: Grease can be applied to the O-ring for ease
of assembling.
NOTE: If a new housing is being installed, tighten
the cap screws to 28 ft-lb.

6. Install the shift fork shaft w/spring into the housing
making sure the shaft O-ring is positioned to the
inside.

CF266A

CC892

7. Install the shift fork assembly making sure the fork
leg is facing upward. Apply a small amount of oil to
the gasket; then install the gasket.

CF267A

4. Apply a liberal coat of grease to the O-ring; then
install it on the assembled cover assembly making
sure to seat the O-ring completely down around the
circumference of the bearing flange.

CC893

8. Place the input shaft assembly onto the gear case
housing; then secure with the existing cap screws.
Tighten to 23 ft-lb.
6-14

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: If a new housing is being installed, tighten
the cap screws to 28 ft-lb.

CF278

CAUTION
CD103

Make sure the tool is free of nicks or sharp edges or
damage to the seal may occur.

3. Repeat steps 1-2 for the opposite side.
INSTALLING DIFFERENTIAL
1. Align the splined input yoke with the front output
splines; then place the differential into position on
the frame and install the cap screws (coated with
blue Loctite #243), washers, and flex-lock nuts.
Tighten to 38 ft-lb. Make sure the rubber boot is
properly seated on the input yoke.

CD110

Removing/Installing Axle Seal
NOTE: This procedure can be performed on a rear
gear case.

1. Remove the seal using a seal removal tool.

CD857

CC899

NOTE: Prior to installing the seal, apply High-Performance #2 Molybdenum Disulphide grease to the
seal outside diameter.

2. Using Gear Case Seal Installer Tool, evenly press the
seal into the cover bore until properly seated.

CD859

2. Pour 275 ml (9.3 fl oz) of SAE 80W-90 hypoid gear
lubricant into the differential and install the fill plug.
Tighten to 16 ft-lb.
3. Install the front drive actuator with the three
torx-head cap screws; then connect the wire connector to the main wiring harness.

www.mymowerparts.com

6-15

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

AG925

AF896D

4. Install the inner fender panels.
5. Install the front axles (see Drive Axles in this section).
6. Secure the upper A-arms with cap screws and lock
nuts. Tighten to 50 ft-lb.

AF895D

9. Install the brake calipers and secure with new
“patch-lock” cap screws tightened to 20 ft-lb.

AF610D

7. Secure the lower shock eyelets with cap screws and
lock nuts. Tighten to 50 ft-lb.

AF894D

10. Install the wheels and tighten to 40 ft-lb (steel
wheels) or 80 ft-lb (aluminum wheels).
11. Remove the ATV from the support stand.

AF897D

8. Secure the tie rods with the lock nuts. Tighten to 30
ft-lb; then install and spread the cotter pins.

Drive Axles
REMOVING REAR DRIVE AXLE
1. Secure the ATV on a support stand to elevate the
wheels.

! WARNING
Make sure the ATV is solidly supported on the support
stand to avoid injury.

6-16

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
2. Pump up the hand brake; then engage the brake lever
lock.
3. Remove the wheel.
4. Remove the cotter pin securing the hex nut; then
remove the hex nut. Release the brake lever lock.

PR729B

KX041

5. Remove the two brake calipers (right side only).
NOTE: Do not allow the brake calipers to hang from
their cable/hose.

CAUTION
The calipers should be supported. If the calipers are
allowed to hang from the cable/hose, damage may
occur.

6. Slide the hub out of the knuckle and set aside.
7. Remove the cap screw and lock nut securing the
knuckle to the upper A-arm. Discard the lock nut.

PR725A

REMOVING FRONT DRIVE AXLE
NOTE: For removing a front drive axle, see Front
Differential in this section.

CLEANING AND INSPECTING

NOTE: Never reuse a lock nut. Once a lock nut has
been removed, it must be replaced with a new lock
nut.

NOTE: Always clean and inspect the drive axle components to determine if any service or replacement is
necessary.

8. While holding the drive axle stationary, pull the top
of the knuckle out and down until it is free of the
drive axle.

1. Using a clean towel, wipe away any oil or grease
from the axle components.

9. Place a drain pan under the ATV to contain any oil
leakage.
10. Push the axle shaft firmly toward the gear case to
release the internal lock; then while holding the axle
in, pull the CV cup from the gear case.

CAUTION
Do not attempt to use a slide hammer or gear case/axle
damage will occur.

CD019

2. Inspect boots for any tears, cracks, or deterioration.
NOTE: If a boot is damaged in any way, it must be
replaced with a boot kit.

3. Inspect the gear case seals for nicks or damage.

www.mymowerparts.com

6-17

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
DISASSEMBLING/INSPECTING/ASSEMBLING AXLES
To disassemble/inspect/assemble the axles, follow the
instruction contained in the appropriate boot repair kit.
INSTALLING REAR DRIVE AXLE
1. Push the axle shaft into the CV cup to release the
detent balls; then while holding the axle firmly in,
push the CV splined end into the gear case.

CD027

7. Install the wheel. Tighten to 40 ft-lb (steel wheels) or
80 ft-lb (aluminum wheels).
8. Remove the ATV from the support stand and release
the brake lever lock.
INSTALLING FRONT DRIVE AXLE

PR725A

1. Position the drive axle in the gear case and steering
knuckle; then insert the upper A-arm ball joint into
the steering knuckle. Secure with a cap screw tightened to 50 ft-lb.
2. Place the brake hose into position on the upper
A-arm; then secure the lower shock eyelet to the
A-arm with a cap screw and a new lock nut. Tighten
to 50 ft-lb.
3. Secure the tie rod to the steering knuckle with a new
lock nut. Tighten securely; then install and spread a
new cotter pin.
4. Slide the hub w/brake disc into position in the steering knuckle followed by a washer and hex nut.
Tighten finger-tight at this time.

PR729B

NOTE: To assure proper seating of the axle, give it a
light pull; the axle should remain “clipped” in place.

2. Swing the knuckle up and onto the drive axle; then
place the knuckle into place in the upper A-arm.
Secure the knuckle to the A-arm with a cap screw
and a new lock nut. Tighten to 35 ft-lb (450) or to 50
ft-lb (1000).

5. Install the brake caliper on the steering knuckle using
new “patch-lock” cap screws. Tighten to 20 ft-lb;
then pump up the hand brake lever and engage the
brake lever lock.
6. Tighten the hub hex nut (from step 4) to 200 ft-lb;
then install and spread a new cotter pin making sure
each side of the pin is flush to the hex nut.

3. Place the hub into position on the axle followed by a
hex nut. Tighten the hex nut finger-tight at this time.
4. If the brake calipers were removed, position them on
the knuckle and secure with new “patch-lock” cap
screws. Tighten the auxiliary brake caliper cap
screws to 20 ft-lb. Tighten the hydraulic brake caliper cap screws to 20 ft-lb.
5. Pump up the hand brake lever; then engage the brake
lever lock.
6. Tighten the hub hex nut (from step 3) to 200 ft-lb;
then install and spread a new cotter pin making sure
each side of the pin is flush to the hex nut.

CD027

7. Install the wheel and tighten to 40 ft-lb (steel wheels)
or 80 ft-lb (aluminum wheels).
8. Remove the ATV from the support stand and release
the brake lever lock.

6-18

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
9. Check the front differential oil level and add oil as
necessary.

AT THIS POINT
For servicing the input shaft (450), pinion gear, needle
bearing, ring gear, and axle seal, see Front Differential
in this section.

RING GEAR/THRUST BUTTON
Removing
1. Remove the cap screws securing the gear case cover
to the gear case; then remove the ring gear.
2. Remove the thrust button from the gear case cover
(left-hand threads). Account for a shim.
CF113A

Inspecting
1. Inspect the ring gear for excessive wear, missing or
chipped teeth, or discoloration.

Rear Gear Case

2. Inspect the thrust button for excessive wear or discoloration.
3. Inspect the bearings for discoloration, roughness, or
excessive wear.

REMOVING
1. Remove the left-side rear A-arms (see Rear A-Arms
in Section 7).

NOTE: For servicing bearings or seals, see Front
Differential in this section.

2. Remove both of the rear drive axles (see Drive Axles
in this section).

Installing/Shimming

3. Remove the four cap screws securing the engine output shaft to the rear gear case input flange.

NOTE: Ring gear clearance must be adjusted prior
to selecting shim for the thrust button.

1. Install the thrust button with shim into the gear case
cover and tighten securely (left-hand threads).

CD028

4. Remove the two cap screws and lock nuts securing
the rear gear case to the frame; then remove the gear
case through the left side.

GC057A

2. Place the ring gear with selected shim into the cover
and measure the ring gear to thrust button clearance
with a thickness gauge. Clearance should be
0.002-0.004 in.

AF960A

www.mymowerparts.com

6-19

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GC058A

GZ176A

3. If clearance is as specified, remove the ring gear and
thrust button; then place a drop of red Loctite #271
on the threads and tighten to 8 ft-lb (left-hand
threads).
4. If clearance is not as specified, repeat steps 1 and 2
using thicker (clearance too great) or thinner (clearance too small) until correct specification is reached.
REAR DRIVE INPUT SHAFT/
HOUSING (1000)
Removing/Disassembling
1. Remove the cap screws securing the rear drive input
shaft/housing to the rear gear case; then remove the
input housing assembly.

GZ177

3. Remove the input shaft from the input housing; then
remove the oil seal.

GZ183

2. Remove the clutch pack from the clutch basket; then
remove the snap ring securing the clutch basket (A)
to the input shaft (B) and remove the clutch basket.

GZ180

GZ182A

GZ392

6-20

www.mymowerparts.com

4. Remove the snap ring retaining the input bearing and
using an appropriate bearing driver, press the bearing
from the housing.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

GZ184A

Cleaning and Inspecting
1. Wash all parts in parts-cleaning solvent and dry with
compressed air.

GZ184

2. Using a suitable seal driver, install a new oil seal into
the front of the input housing until the seal flush with
the housing.

! WARNING
Always wear safety glasses when working with compressed air.

2. Clean all gasket material and sealant from mating
surfaces.
3. Inspect bearings, shafts, and housing for excessive
wear, cracks, or discoloration.
4. Inspect the clutch basket for wear in splines or cracks
in the housing.
GZ182A

3. Apply grease to the lips of the oil seal; then install
the input shaft into the input bearing and housing.

GZ178A

5. Inspect the clutch pack for signs of discoloration.
NOTE: The clutch pack is not a serviceable component. If worn, discolored, or damaged in any way, it
must be replaced.

Assembling/Installing

GZ179A

4. Install the clutch basket onto the input shaft and
secure with the snap ring (flat side directed outward);
then install the clutch pack into the basket.

1. Install a new bearing into the input housing and
secure with the snap ring (flat side directed away
from bearing).

www.mymowerparts.com

6-21

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
3. Remove the hex nut securing the hub.
4. Remove the brake caliper.

GZ176

5. Using a new gasket, install the assembled rear drive
input shaft/housing onto the rear drive gear case and
secure with the three cap screws. Tighten to 23 ft-lb.

PR243A

5. Remove the hub assembly.

INSTALLING

6. Remove the four cap screws securing the brake disc.

1. Slide the gear case into position through the left side
of the frame; then secure it to the frame with cap
screws and lock nuts. Tighten to 45 ft-lb.

CLEANING AND INSPECTING

2. Secure the engine output shaft to the rear gear case
input flange with four cap screws and lock nuts.
Tighten to 20 ft-lb.

NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

3. Install the rear drive axles (see Drive Axles in this
section).
4. Install the left-side rear A-arms (see Rear A-Arms in
Section 7).

1. Clean all hub components.
2. Inspect all threads for stripping or damage.
3. Inspect the brake disc for cracks or warping.
4. Inspect the hub for pits, cracks, loose studs, or spline
wear.

Hub

INSTALLING
1. Secure the brake disc to the hub with the four cap
screws coated with blue Loctite #243. Tighten to 15
ft-lb.

REMOVING
1. Secure the ATV on a support stand to elevate the
wheel; then remove the wheel.

2. Apply grease to the splines in the hub.
3. Install the hub assembly onto the shaft.

! WARNING
Make sure the ATV is solidly supported on the support
stand to avoid injury.

2. Remove the cotter pin from the nut.
NOTE: During assembly, new cotter pins should be
installed.

PR290

4. Secure the hub assembly with the hex nut. Tighten
only until snug.
5. Secure the brake caliper to the knuckle with two new
“patch-lock” cap screws. Tighten the auxiliary caliper to 20 ft-lb. Tighten the hydraulic caliper to 20
ft-lb.
KX041

6-22

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

PR243A

AF637D

6. Tighten the hex nut (from step 4) to 200 ft-lb; then
install and spread a new cotter pin making sure each
side of the pin is flush to the hex nut.

2. Place an absorbent towel around the connection to
absorb brake fluid. Remove the banjo-fitting from
the master cylinder. Account for two crush washers
and a banjo-fitting bolt.

NOTE: If the cotter pin does not line up, always
tighten to the next alignment.

DE059A
PR260

7. Install the wheel and tighten to 40 ft-lb (steel wheels)
or 80 ft-lb (aluminum wheels).
8. Remove the ATV from the support stand.

Hand Brake Lever/Master
Cylinder Assembly

CAUTION
Brake fluid is highly corrosive. Do not spill brake fluid
on any surface of the ATV.

3. Remove the snap ring and pivot pin securing the
brake lever to the master cylinder housing; then
remove the brake lever and set aside.
4. Dislodge the brakelight switch from the master cylinder housing by gently pressing it toward the pivot
pin hole in the housing; then lay it aside leaving the
switch and wiring harness connected.

NOTE: The master cylinder is a non-serviceable
component; it must be replaced as an assembly.

REMOVING
1. Slide a piece of flexible tubing over one of the wheel
bleeder valves and direct the other end into a container. Remove the reservoir cover; then open the
bleeder valve. Allow the brake fluid to drain completely.
NOTE: Compressing the brake lever several times
will quicken the draining process.
BC205

5. Remove the clamp screws securing the brake housing to the handlebar; then remove the assembly from
the handlebar.

www.mymowerparts.com

6-23

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

DE058A

INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

DE059A

3. Gently press the brakelight switch into the housing
(left to right) until the mounting tabs snap into the
four locating holes; then install the brake lever, pivot
pin, and snap ring.

1. Inspect the pin securing the brake lever for wear.
2. Inspect the brake lever for elongation of the pivot
hole.
3. Inspect the reservoir for cracks and leakage.
4. Inspect the banjo-fitting for cracks and deterioration
and the condition of the fittings (threaded and compression).
5. Inspect the brakelight switch for corrosion, cracks,
missing or broken mounting tabs, or broken and
frayed wiring.
NOTE: If the brakelight switch is determined to be
not serviceable, see Section 5.

BC206

4. Bleed the brake system (see Section 2).

Hydraulic Brake Caliper

INSTALLING
1. Position the brake housing on the handlebar. Secure
with clamp screws; then tighten securely.

! WARNING
Arctic Cat recommends that only authorized Arctic Cat
ATV dealers perform hydraulic brake service. Failure to
properly repair brake systems can result in loss of control causing severe injury or death.

REMOVING/DISASSEMBLING
1. Secure the ATV on a support stand to elevate the
wheel; then remove the wheel.

! WARNING
DE058A

2. Using two new crush washers, connect the banjo-fitting to the master cylinder; then secure with the
banjo-fitting bolt. Tighten to 20 ft-lb.

Make sure the ATV is solidly supported on the support
stand to avoid injury.

! WARNING
Never let brake fluid contact the eyes. Damage to the
eyes will occur. Always wear appropriate protective
safety goggles and latex gloves when handling brake
fluid.

2. Drain the brake fluid from the caliper, hose, and
master cylinder through the bleed screw by pumping
the brake lever/pedal.
6-24

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

PR235

CAUTION
Brake fluid is highly corrosive. Do not spill brake fluid
on any surface of the ATV and do not reuse brake fluid.

PR238

5. Remove the caliper holder from the caliper and discard the O-ring.

NOTE: Whenever brake components are removed,
disassembled, or repaired where brake fluid is
exposed to air, drain all fluid and replace with new
DOT 4 brake fluid from an unopened container. Brake
fluid readily absorbs moisture from the air significantly lowering the boiling point. This increases the
chance of vapor lock reducing braking power and
increasing stopping distance.

3. Remove the brake hose from the caliper and close
the bleed screw; then remove the caliper.
4. Compress the caliper holder against the caliper
(opposite the O-ring side) and remove the outer
brake pad; then remove the inner brake pad.
NOTE: If brake pads are to be returned to service,
do not allow brake fluid to contaminate them.

PR239B

NOTE: The O-ring is used for shipping purposes
and provides no function in operation.

6. Cover the piston end of the housing with a shop
towel; then keeping fingers clear of piston travel,
apply compressed air to the fluid port to blow the
piston free of the housing. Account for two seal
rings in the housing.

PR237A

PR713A

www.mymowerparts.com

6-25

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

PR715

! WARNING
Make sure to hold the towel firmly in place or the piston
could be ejected from the housing causing injury.

PR717A

2. Press the piston into the caliper housing using hand
pressure only. Completely seat the piston; then wipe
off any excessive brake fluid.

7. Using an appropriate seal removal tool, carefully
remove the seals from the brake caliper housing; then
remove four O-rings from the brake caliper housing
noting the location of the different sized O-rings. Discard all seals, O-rings, and crush washers.
CLEANING AND INSPECTING
1. Clean all caliper components (except the brake pads)
with DOT 4 brake fluid. Do not wipe dry.
2. Inspect the brake pads for damage and excessive
wear.
NOTE: For measuring brake pads, see Section 2.

PR711A

3. Inspect the brake caliper housings for scoring in the
piston bores, chipped seal ring grooves, or signs of
corrosion or discoloration.
4. Inspect the piston surface for scoring, discoloration,
or evidence of binding or galling.
5. Inspect the caliper holder for wear or bending.
ASSEMBLING/INSTALLING
1. Install new seals into the brake caliper housing and
apply a liberal amount of DOT 4 brake fluid to the
cylinder bore of the housing, seals, and brake piston.

CAUTION
Make sure the seals are properly in place and did not
twist or roll during installation.

PR712

3. Apply high-temperature silicone grease (supplied
with the O-ring kit) to the inside of the caliper holder
bores and O-rings; then install the four O-rings into
the caliper.

PR719C
PR715

6-26

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
4. Install the caliper onto the caliper holder making sure
the caliper and holder are correctly oriented.
NOTE: It is very important to apply silicone grease
to the O-rings and caliper bores prior to assembly.

PR239

6. Place the brake caliper assembly into position and
secure with new “patch-lock” cap screws. Tighten
the caliper to 20 ft-lb.
PR239C

5. Making sure brake fluid does not contact the brake pads,
compress the caliper holder toward the caliper and
install the inner brake pad; then install the outer pad.

CAUTION
If brake pads become contaminated with brake fluid, they
must be thoroughly cleaned with brake cleaning solvent
or replaced with new pads. Failure to do so will result in
reduced braking and premature brake pad failure.

7. Place a new crush washer on each side of the brake
hose fitting and install it on the caliper. Tighten to 20
ft-lb.
8. Fill the reservoir; then bleed the brake system (see
Section 2).

! WARNING
Never use brake fluid from an open container or reuse
brake fluid. Moisture-contaminated brake fluid could
cause vapor build-up (expansion) during hard braking
resulting in greatly increased stopping distance or loss
of control leading to injury or death.

9. Install the wheel. Tighten to 40 ft-lb (steel wheels) or
80 ft-lb (aluminum wheels).
10. Remove the ATV from the support stand and verify
brake operation.

PR238

www.mymowerparts.com

6-27

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Troubleshooting Drive
System
Problem: Power not transmitted from engine to wheels
Condition
1. Rear axle shafts serration worn - broken

Remedy
1. Replace shaft

Problem: Power not transmitted from engine to either front wheel
Condition
1. Secondary drive - driven gear teeth broken
2. Propeller shaft serration worn - broken
3. Coupling damaged
4. Coupling joint serration worn - damaged
5. Front drive - driven bevel gears broken - damaged
6. Front differential gears/pinions broken - damaged
7. Sliding dogs/shaft fork worn - damaged
8. Front drive axle worn - damaged
9. Front drive axle serration worn - damaged

Remedy
1. Replace gear(s)
2. Replace shaft
3. Replace coupling
4. Replace joint
5. Replace gear(s)
6. Replace gears - pinions
7. Replace gear(s)
8. Replace axle
9. Replace axle

Troubleshooting Brake
System
Problem: Braking poor
Condition
1.
2.
3.
4.
5.

Pad worn
Pedal free-play excessive
Brake fluid leaking
Hydraulic system spongy
Master cylinder/brake cylinder seal worn

Problem: Brake lever travel excessive
Condition
1.
2.
3.
4.

Hydraulic system entrapped air
Brake fluid low
Brake fluid incorrect
Piston seal - cup worn

Problem: Brake fluid leaking
Condition
1. Connection joints loose
2. Hose cracked
3. Piston seal worn

6-28

www.mymowerparts.com

Remedy
1.
2.
3.
4.
5.

Replace pads
Replace pads
Repair - replace hydraulic system component(s)
Bleed hydraulic system - correct or repair leaks
Replace master cylinder

Remedy
1.
2.
3.
4.

Bleed hydraulic system
Add fluid to proper level
Drain system - replace with correct fluid
Replace master cylinder

Remedy
1. Tighten joint
2. Replace hose
3. Replace brake caliper

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

SECTION 7 - SUSPENSION

TABLE OF
CONTENTS
Suspension ............................................................. 7-2
Shock Absorbers ..................................................... 7-2
Front A-Arms ........................................................... 7-3
Rear A-Arms ........................................................... 7-5
Wheels and Tires .................................................... 7-7
Troubleshooting ....................................................... 7-8

www.mymowerparts.com

7-1

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Suspension
The following suspension system components should be
inspected periodically to ensure proper operation.
A. Shock absorber rods not bent, pitted, or damaged.
B. Rubber damper not cracked, broken, or missing.
C. Shock absorber body not damaged, punctured, or
leaking.
D. Shock absorber eyelets not broken, bent, or
cracked.

AF626D

4. Compress the shock absorber spring, remove the
retainer, and remove the spring.

E. Shock absorber eyelet bushings not worn, deteriorated, cracked, or missing.
F. Shock absorber spring not broken or sagging.
NOTE: Critical torque specifications are located in
Section 1.

Shock Absorbers
REMOVING
1. Secure the ATV on a support stand to elevate the
wheels and to release load on the suspension.

! WARNING
Make sure the ATV is solidly supported on the support
stand to avoid injury.

2. Remove the two cap screws and nuts securing each
front shock absorber to the frame and the upper
A-arm. Account for bushings and sleeves from each.

AF730D

CLEANING AND INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Clean all shock absorber components using a pressure washer.
2. Inspect each shock rod for nicks, pits, rust, bends,
and oily residue.
3. Inspect all springs, spring retainers, shock rods,
sleeves, bushings, shock bodies, and eyelets for
cracks, leaks, and bends.
INSTALLING
1. Place the shock absorber spring over the shock
absorber, compress the spring, and install the
retainer.

AF605D

CAUTION
Additional support stands are necessary to support the
rear axle when the shock absorbers are removed or
damage may occur.

3. Remove the two cap screws and nut securing each
rear shock absorber to the frame and lower A-arm.
Account for bushings and sleeves from each.
7-2

www.mymowerparts.com

2. Place bushings and sleeves (where appropriate) into
shock eyelet; then install shock with two cap screws
and nuts. Tighten all front suspension nuts to 50
ft-lb. Tighten rear suspension nuts (upper) to 50 ft-lb;
tighten lower shock-to-A-arm nuts to 20 ft-lb.

CAUTION
Do not tighten the nuts beyond the recommended specification or the shock eyelet or mount WILL be damaged.

NOTE: The rear shock absorber-to-lower A-arm
torque factor is 20 ft-lb.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
3. Remove the ATV from the support stand.

Front A-Arms
REMOVING
1. Secure the ATV on a support stand to elevate the
front wheels; then remove the wheels.

! WARNING
Make sure the ATV is solidly supported on the support
stand to avoid injury.

2. Remove the cotter pin from the nut. Discard the cotter pin.

AF618D

7. Remove the cap screws securing the ball joints to the
knuckle.

CAUTION
Support the knuckle when removing the cap screws or
damage to the threads will occur.

CD008

3. Remove the nut securing the hub.
4. Remove the brake caliper. Account for two cap
screws.

PR203

8. Tap the ball joints out of the knuckle; then remove
the knuckle.
9. Remove the lower shock absorber eyelet from the
upper A-arm.
10. Remove the cap screws securing the A-arms to the
frame.

PR377B

NOTE: Do not allow the brake caliper to hang from
the cable/hose.

5. Remove the hub assembly.
6. Remove the cotter pin and slotted nut securing the tie
rod end to the knuckle; then remove the tie rod end
from the knuckle.

www.mymowerparts.com

AF610D

11. Remove the circlip from the ball joint; then remove
the ball joint from the A-arm.

7-3

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

AF616D

CLEANING AND INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

AF610D

3. Route the brake hose through the upper A-arm shock
absorber mount; then secure the hose to the A-arm
with a cable tie and grommet.

1. Clean all A-arm components using a pressure
washer.
2. Clean the ball joint mounting hole of all residual
Loctite, grease, oil, or dirt for installing purposes.
3. Inspect the A-arm for bends, cracks, and worn bushings.
4. Inspect the ball joint mounting holes for cracks or
damage.
5. Inspect the frame mounts for signs of damage, wear,
or weldment damage.
INSTALLING
1. Apply Loctite Primer “T” to the arm socket; then
apply green Loctite #609 to the entire outside diameter of the ball joint. Install the ball joint into the
A-arm and secure with the snap ring.

DE054A

4. Secure the lower eyelet of the shock absorber to the
upper A-arm. Tighten nut to 50 ft-lb.
5. Secure the A-arm assemblies to the frame mounts
(from step 2). Tighten the cap screws to 50 ft-lb.

CAUTION
Do not tighten the nut beyond the 50 ft-lb specification
or the shock eyelet or mount WILL be damaged.

6. Install the knuckle assembly onto the ball joints and
secure with cap screws. Tighten to 35 ft-lb.

AF616D

2. Install the A-arm assemblies into the frame mounts
and secure with the cap screws. Only finger-tighten
at this time.
AF628D

7. Install the tie rod end and secure with the nut.
Tighten to 30 ft-lb; then install a new cotter pin and
spread the pin to secure the nut.
NOTE: During assembly, new cotter pins should be
installed.
7-4

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

AF618D

CD008

8. Apply grease to the hub and drive axle splines; then
install the hub assembly onto the drive axle.

13. Install the wheel and tighten to 40 ft-lb (steel wheels)
or 80 ft-lb (aluminum wheels).
14. Remove the ATV from the support stand.

Rear A-Arms
REMOVING
1. Secure the ATV on a support stand to elevate the
wheels.

! WARNING
CD009

9. Secure the hub assembly with the nut. Tighten only
until snug.
10. Secure the brake caliper to the knuckle with two new
“patch-lock” cap screws. Tighten to 20 ft-lb.

Make sure the ATV is solidly supported on the support
stand to avoid injury.

2. Pump up the hand brake; then engage the brake lever
lock.
3. Remove the wheel.
4. Remove the cotter pin securing the hex nut; then
remove the hex nut. Release the brake lever lock.
5. Remove the caliper (right side only).
NOTE: Do not allow the brake caliper to hang from
the cable/hose.

6. Remove the cap screws and lock nut securing the
shock absorber to the frame and lower A-arm; then
remove the shock absorber.
7. Remove the cap screws securing the boot guard to
the lower A-arm.
CD007

11. Secure the hub nut (from step 9) to the shaft/axle.
Tighten to 200 ft-lb.
NOTE: If the cotter pin does not line up, always
tighten to the next alignment.

12. Install a new cotter pin and spread the pin to secure
the nut.

AF934

www.mymowerparts.com

7-5

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
8. Slide the hub out of the knuckle and set aside.
9. Remove the cap screws and lock nuts securing the
knuckle to the A-arms. Discard the lock nuts.
NOTE: Never reuse a lock nut. Once a lock nut has
been removed, it must be replaced with a new lock nut.

10. Remove the cap screws and lock nuts securing the
A-arms to the frame; then remove the A-arms.
NOTE: If removing the upper right A-arm, it will be
necessary to disconnect the brake hose from the
A-arm.
DE054A

CLEANING AND INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Clean all A-arm components using a pressure
washer.
2. Inspect the A-arm for bends, cracks, and worn bushings.

7. Compress the hand brake lever and engage the brake
lever lock; then secure the hub nut (from step 5) to
the drive axle. Tighten to 200 ft-lb.
8. Install a new cotter pin and spread the pin to secure
the nut.
NOTE: If the cotter pin does not line up, always
tighten to the next alignment.

3. Inspect the frame mounts for signs of damage, wear,
or weldment damage.
INSTALLING
1. Install the A-arm assemblies into the frame mounts
and secure with the cap screws and new lock nuts.
Only finger-tighten at this time.
2. Slide the knuckle onto the drive axle and into position on the A-arms; then secure the knuckle to the
A-arms with cap screws and new lock nuts. Tighten
to 35 ft-lb (450 models) or 50 ft-lb (1000 models).
3. Tighten the hardware securing the A-arms to the
frame mounts (from step 1) to 50 ft-lb.
4. Apply grease on the drive axle splines; then install
the hub assembly onto the drive axle.

PR260

9. Secure the shock absorber to the frame with a cap
screw and new lock nut. Tighten to 50 ft-lb.
10. Secure the shock absorber to the lower A-arm with a
cap screw and new lock nut. Tighten to 20 ft-lb.
11. Secure the boot guard to the lower A-arm with the
two cap screws. Tighten securely.
12. Install the wheel and tighten to 40 ft-lb (steel wheels)
or 80 ft-lb (aluminum wheels).
13. Remove the ATV from the support stand.

Wheels and Tires
PR290

5. Secure the hub assembly with the nut. Tighten only
until snug.
6. Secure the brake caliper to the knuckle with two new
“patch-lock” cap screws (right side only). Tighten
the caliper to 20 ft-lb.
NOTE: Ensure that the brake hose is properly
routed and secured to the upper A-arm.
7-6

www.mymowerparts.com

TIRE SIZE

! WARNING
Use only Arctic Cat approved tires when replacing tires.
Failure to do so could result in unstable ATV operation.

The ATV is equipped with low-pressure tubeless tires of
the size and type listed in Section 1. Do not under any
circumstances substitute tires of a different type or size.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
! WARNING
Do not mix tire tread patterns. Use the same pattern
type on front and rear. Failure to heed warning could
cause poor handling qualities of the ATV and could
cause excessive drive train damage not covered by warranty.

NOTE: Make sure each wheel is installed on its
proper hub as noted in removing (the “rotation
arrow” (if applicable) must indicate forward direction
of rotation).

TIRE INFLATION PRESSURE
Front and rear tire inflation pressure should be as specified in Section 1.
REMOVING
1. Secure the ATV on a support stand to elevate the
wheels.

! WARNING
Make sure the ATV is solidly supported on the support
stand to avoid injury.

2. Remove the wheels.
NOTE: Keep left-side and right-side wheels separated for installing them on their proper sides.

CLEANING AND INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Clean the wheels and hubs using a pressure washer.
2. Inspect each wheel for cracks, dents, or bends.
3. Inspect each tire for cuts, wear, missing lugs, and
leaks.
INSTALLING
Install each wheel on its hub. Tighten to 40 ft-lb (steel
wheels) or 80 ft-lb (aluminum wheels).

www.mymowerparts.com

AF612D

CHECKING/INFLATING
1. Using an air pressure gauge, measure the air pressure
in each tire. Adjust the air pressure as necessary to
meet the recommended inflation pressure.
2. Inspect the tires for damage, wear, or punctures.

! WARNING
Do not operate the ATV if tire damage exists.

NOTE: Be sure all tires are the specified size and
have identical tread pattern.
NOTE: If pulling is noted, measure the circumference of the front and rear tires on the pulling side.
Compare the measurements with the tires on the
opposite side. If pulling is noted during braking only,
check and adjust the brakes as necessary and
recheck operation (see Section 2).

7-7

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Troubleshooting
Problem: Suspension too soft
Condition
1. Spring(s) weak
2. Shock absorber damaged
3. Shock absorber preload too low

Problem: Suspension too stiff
Condition
1. A-arm-related bushings worn
2. Shock absorber preload too high

Problem: Suspension noisy
Condition
1. Cap screws (suspension system) loose
2. A-arm-related bushings worn

Problem: Rear wheel oscillation
Condition
1.
2.
3.
4.
5.
6.
7.
8.

Rear wheel hub bearings worn - loose
Tires defective - incorrect
Wheel rim distorted
Wheel hub cap screws loose
Auxiliary brake adjusted incorrectly
Rear suspension arm-related bushing worn
Rear shock absorber damaged
Rear suspension arm nut loose

Problem: Vehicle pulling or steering erratic
Condition
1. Vehicle steering is erratic on dry, level surface
2. Vehicle pulls left or right on dry, level surface

7-8

www.mymowerparts.com

Remedy
1. Replace spring(s)
2. Replace shock absorber
3. Adjust shock absorber preload

Remedy
1. Replace bushing
2. Adjust shock absorber preload

Remedy
1. Tighten cap screws
2. Replace bushings

Remedy
1.
2.
3.
4.
5.
6.
7.
8.

Replace bearings
Replace tires
Replace rim
Tighten cap screws
Adjust brake
Replace bushing
Replace shock absorber
Tighten nut

Remedy
1. Check front wheel alignment and adjust if necessary (see
Section 8)
2. Check air pressure in tires and adjust to specifications

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

SECTION 8 STEERING/FRAME/CONTROLS

TABLE OF
CONTENTS
Steering/Frame/Controls ............................................ 2
LCD Gauge ................................................................ 2
Steering Post/Tie Rods .............................................. 2
Handlebar Grip ........................................................... 6
Throttle Control .......................................................... 7
Steering Knuckles ...................................................... 8
Measuring/Adjusting Toe-Out ................................... 10
Shift Lever ................................................................ 11
Front Rack ................................................................ 11
Front Bumper Assembly ........................................... 11
Front Body Panel/Side Panels.................................. 12
Footrests .................................................................. 15
Belly Panel ............................................................... 15
Exhaust System ....................................................... 16
Rear Body Panel/Rack ............................................. 16
Taillight Assembly..................................................... 17
Seat .......................................................................... 17
Troubleshooting ........................................................ 18

www.mymowerparts.com

8-1

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Steering/Frame/Controls
The following steering components should be inspected
periodically to ensure safe and proper operation.
A. Handlebar grips not worn, broken, or loose.
B. Handlebar not bent, cracked, and has equal and
complete full-left and full-right capability.
C. Steering post bearing assembly/bearing housing
not broken, worn, or binding.

FI463A

D. Ball joints not worn, cracked, or damaged.
E. Tie rods not bent or cracked.
F. Knuckles not worn, cracked, or damaged.
G. Cotter pins not damaged or missing.
The frame, welds, and racks should be checked periodically for damage, bends, cracks, deterioration, broken
components, and missing components.
NOTE: Critical torque specifications are located in
Section 1.
FI464A

LCD Gauge

2. Remove the reinstallable rivets securing the radiator
access cover and remove the cover.

REPLACING
To replace the gauge, use the following procedure.
1. Remove the two reinstallable rivets securing the
instrument pod; then remove the ignition switch
retaining ring.
2. Remove the two nuts securing the mounting studs;
then remove the gauge and disconnect the
multi-pin connector.
3. Mount the gauge and secure with the two nuts;
then connect the multi-pin connector.

FI465A

3. Remove four reinstallable rivets securing the steering post cover and remove the cover.

4. Install the instrument pod and secure with the reinstallable rivets.
5. Secure the ignition switch with the retaining ring.

Steering Post/Tie Rods
REMOVING
1. Remove the ignition switch retaining ring; then
remove the reinstallable rivets securing the instrument pod to the mounting bracket and remove the
pod and LCD gauge.

8-2

www.mymowerparts.com

FI466A

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
4. Unlatch the storage compartment lid; then slide the
storage compartment cover assembly forward and
lift off.

CD760

8. Using a suitable lift stand, raise the ATV enough to
remove the front wheels.
FI467A

5. Remove the storage compartment.

CD685

FI468

NOTE: For models not equipped with electronic
power steering, proceed to step 13.

6. Remove the four cap screws securing the handlebar
caps and LCD gauge bracket to the steering post;
then move the handlebar and gauge out of the way.
Account for four handlebar caps.

9. Remove the left front shock absorber; then remove
the cap screws and nuts from the steering post to the
EPS couplers.

CD762

7. Remove two cap screws securing the upper steering
post bearing to the frame. Account for two housings.

EPS005A

10. Pull upward on the handlebar to disengage the upper
coupler from the EPS assembly.
11. Disconnect the 2-pin and 8-pin connectors from the
top of the EPS housing.

www.mymowerparts.com

8-3

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

EPS007A

12. Remove four cap screws securing the EPS housing to
the frame; then lift the assembly upward sufficiently
to disengage the lower coupler and remove from the
left side.

CAUTION
Do not attempt to disassemble the EPS assembly as
there are no serviceable components within the assembly and damage will occur voiding the EPS warranty.

13. Remove the cotter pins and slotted nuts from the
inner and outer tie rod ends; then remove the tie rods
from the steering post arm and the left-side and
right-side steering knuckles.

AL600D

CLEANING AND INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Clean and inspect the pivot area for wear. Apply a
low-temperature grease to the ends.

! WARNING
Always wear safety glasses when using compressed
air.

2. Inspect the tie rods for damaged threads or wear.
3. Inspect the tie rods for cracks or unusual bends.
4. Inspect all welded areas for cracks or deterioration.
5. Inspect the steering post and steering-post brackets
for cracks, bends, or wear.
6. Inspect the bearing halves, bearing caps, and bearing
housings for cracks or wear.
7. Inspect the handlebar tube for cracks, wear, or
unusual bends.
8. Inspect the handlebar grips for damage or wear.

AF778D

INSTALLING (Models Without
Electronic Power Steering)
1. Place the steering post into position; then secure the
lower bearing flange to the frame with two cap
screws. Tighten to 20 ft-lb.

KX039

14. Remove two cap screws securing the lower steering
post bearing flange to the frame; then remove the
steering post.
AL600D

8-4

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
2. Place the upper steering post bearings into the housings; then position on the steering post and secure the
housings to the frame with two cap screws. Tighten
to 20 ft-lb.

FI464A

CD760

3. Install the tie rods and secure with the slotted nuts.
Tighten to 30 ft-lb; then install new cotter pins.
NOTE: If the slots do not align with the holes in the
tie rod ends, tighten the nuts just enough to allow
installation of the cotter pins.

FI463A

8. Install the steering post access cover and secure with
four reinstallable rivets; then install and secure the
radiator access cover.

AF778D

4. Install the front wheels and tighten to 40 ft-lb (steel
wheels) or 80 ft-lb (aluminum wheels) using a crisscross pattern.
5. Lower the ATV and place the handlebar and caps
into position on the steering post; then position the
LCD gauge on top of the caps and secure with the
four cap screws. Tighten securely.

8
FI466A

6. Install the storage compartment box; then attach the
storage compartment cover assembly by engaging
the tabs into the slots and sliding rearward. Lock the
storage compartment lid to hold the assembly in
place.
7. Place the instrument pod into position; then secure
with two reinstallable rivets and the ignition switch
retaining ring.

FI465A

www.mymowerparts.com

8-5

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
INSTALLING (Electronic Power
Steering Models)
1. Place the lower steering post into position; then
secure the lower bearing flange to the frame with two
cap screws. Tighten to 20 ft-lb.

AF778D

AL600D

2. Making sure the double spline is aligned to the slot in
the lower coupler, install the EPS output shaft into
the lower coupler; then install the four caps screws
securing the EPS housing to the frame. Tighten to 35
ft-lb.
EPS005A

4. Connect the 2-pin and 8-pin connectors to the EPS
assembly.
5. Install the upper steering post support to the frame
and secure with two cap screws. Tighten to 20 ft-lb.
6. Install the storage compartment, steering post and
radiator access panels, and storage compartment
cover; then install the shock absorber and tighten to
50 ft-lb.
EPS008A

7. Install the front wheels and tighten the nuts to 40
ft-lb (steel wheels) or 80 ft-lb (aluminum wheels).

Handlebar Grip
REMOVING
1. Loosen but do not remove the cap screws in the end
of the handlebar; then tap lightly on the head to dislodge the handlebar plug.

EPS007

8-6

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
2. Slide the grommet out of the lower half of the throttle control; then remove the cable from the actuator
arm.

KC310

AF676D

3. Remove the cap screw, lock washer, and washer
securing the actuator arm to the throttle control lever.

KC309A

2. Grasp the end and remove the cap screw, plug, and
end cap.
INSPECTING
NOTE: Whenever a part is worn excessively, cracked,
or damaged in any way, replacement is necessary.

1. Inspect the grip for wear, cuts, or cracks.
2. Inspect the grip for deterioration.

AF677D

4. Remove the actuator arm and account for a bushing.
Note the position of the return spring for installing
purposes.

3. If a grip is damaged, cut the grip lengthwise using a
sharp knife or box cutter; then peel off the grip.
INSTALLING

NOTE: Before installing a grip, use contact removal
spray or alcohol to clean the handlebar of glue residue, oil, or any other contaminant.

1. Apply a liberal amount of Handlebar Grip Adhesive
to the inside of a new grip.
2. Slide the grip onto the handlebar until it is fully
seated with the smooth part of the grip facing up.
3. Wipe off any excess glue; then secure the grip with
the handlebar end-cap.

Throttle Control

AF678D

INSTALLING
1. Place the return spring into the throttle control; then
place the bushing and actuator arm into position.
Secure with the cap screw, lock washer, and washer.

REMOVING
1. Remove the two machine screws securing the throttle control to the handlebar.

www.mymowerparts.com

8-7

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
7. Remove the two cap screws securing the ball joints
in the knuckle.
8. Tap the ball joint end out of the knuckle; then
remove the knuckle.
9. Remove the snap ring from the knuckle; then remove
the bearing.

AF679D

2. Using a pair of needle-nose pliers, place the spring
into position on the actuator arm.

PR287A

AF680D

3. Place the two halves of the throttle control onto the
handlebar and secure with the two machine screws.
ADJUSTING
To adjust throttle cable free-play, see Section 4.

PR288

CAUTION

Steering Knuckles
REMOVING AND DISASSEMBLING
1. Secure the ATV on a support stand to elevate the
wheel; then remove the wheel.

! WARNING
Make sure the ATV is solidly supported on the support
stand to avoid injury.

2. Remove the wheel cap from the hub; then remove
the cotter pin from the nut.
3. Remove the nut securing the hub.
4. Remove the brake caliper.
NOTE: Do not allow the brake caliper to hang from
the cable/hose.

5. Remove the hub assembly.
6. Remove the cotter pin from the tie rod end and
remove the tie rod end from the knuckle.
8-8

www.mymowerparts.com

Use extreme care when removing the bearing. If the
bearing is allowed to fall, it will be damaged and will
have to be replaced.

CLEANING AND INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Clean all knuckle components.
2. Inspect the bearing for pits, gouges, rusting, or premature wear.
3. Inspect the knuckle for cracks, breaks, or porosity.
4. Inspect threads for stripping or damage.
ASSEMBLING AND INSTALLING
1. Install the bearing; then install the snap ring making
sure it seats into the knuckle.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

PR287A

PR290A

2. Install the knuckle to the upper and lower ball joints
and secure with the two cap screws. Tighten to 35
ft-lb.

5. Install the hub assembly onto the splines of the shaft.
6. Secure the hub assembly with the nut. Tighten only
until snug.

AF628D

3. Install the tie rod end and secure with the nut.
Tighten to 30 ft-lb; then install a new cotter pin and
spread the pin.

PR257

7. Secure the brake caliper to the knuckle with new
“patch-lock” cap screws. Tighten to 20 ft-lb.

NOTE: During assembling, new cotter pins should
be installed.

8
PR264A

8. Pump the hand brake lever; then engage the brake
lever lock.
AF618D

4. Apply a small amount of grease to the hub splines.

9. Secure the hub nut (from step 6) to the shaft. Tighten
to 200 ft-lb.
10. Install a new cotter pin and spread the pin to secure
the nut.
11. Install the wheel; then using a crisscross pattern,
tighten to 40 ft-lb (steel wheels) or 80 ft-lb (aluminum wheels).
12. Remove the ATV from the support stand.

www.mymowerparts.com

8-9

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Measuring/Adjusting
Toe-Out
1. Thoroughly wash the ATV to remove excess weight
(mud, etc.).
2. Refer to the specifications and ensure the tires are
properly inflated to the recommended pressure.
NOTE: Ensure the inflation pressure is correct in
the tires or inaccurate measurements can occur.

AF785D

3. Place the ATV in a level position taking care not to
push down or lift up on the front end; then turn the
handlebar to the straight ahead position.
NOTE: When measuring and adjusting, there
should be a normal operating load on the ATV (without an operator but with Arctic Cat approved accessories).

4. Measure the distance from the outside edge of each
handlebar grip to equal reference points on each.
AF786D

NOTE: The distances from the inside rims to the
frame tubes should be equal. If the measurements
are equal, proceed to step 8; if the measurements are
not equal, proceed to step 7.

7. To make the measurements equal, loosen the appropriate tie rod jam nuts and adjust accordingly; then
proceed to step 8.

DE047A

5. Adjust the handlebar direction until the two measurements are equal; then secure the handlebar to the rear
rack using tie-down straps.
NOTE: Care must be taken not to allow the handlebar to turn while securing it.

AF617D

CD014

6. Measure the distance from the inside of each front
rim to the lower frame tube.
AF778D

8-10

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: The front wheels do not have to be removed
to adjust the tie rod. Also, care should be taken not to
disturb the handlebar position.

2. Remove two cap screws, two self-tapping screws,
and three nylon ties securing the left-side splash
panel and remove the panel.

8. Using a permanent marker of some type, mark the
center of each front tire (at a height parallel to the
belly panel).

3. Remove the axle and nut securing the shift lever to
the upper shift arm; then remove the shift lever.
Account for a spring and two O-rings.
INSTALLING
1. Place the spring into position between the upper shift
arm and shift lever; then making sure the O-rings are
in place on the axle, secure the shift lever to the arm
with the existing axle and nut.
2. Place the shift rod into position on the shift lever and
secure with the existing E-clip.
3. Check shift lever adjustment (see Section 2); then
tighten jam nut(s) securely.
4. Install the left-side splash panel.

AF789D

9. Measure the distance between the marks (at a height
parallel to the belly panel) at the front side; then
record the measurement.
10. Push the ATV forward until the marks are parallel to
the belly panel on the back side; then measure the
distance between the marks.
11. The difference in the measurements must show
1/8-1/4 in. toe-out (the front measurement 1/8-1/4 in.
more than the rear measurement).
12. If the difference in the measurements is not within
specifications, adjust both tie rods equally until
within specifications.
NOTE: Prior to locking the jam nuts, make sure the
ball joints are at the center of their normal range of
motion and at the correct angle.

Front Rack
REMOVING
1. Remove the cap screws and lock nuts securing the
rack to the frame and front fender panel.
2. Remove the front rack from the ATV.
CLEANING AND INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Clean all rack components using a pressure washer.
2. Inspect all welds for cracking or bending.
3. Inspect threaded areas of all mounting bosses for
stripping.

4. Inspect for missing decals and/or reflectors.
INSTALLING
1. Place the rack into position on the frame and front
fender panel. Install the cap screws and lock nuts and
finger-tighten only.
2. Install the two cap screws and lock nuts securing the
rack to the fenders. Tighten all hardware securely.
733-559A

Front Bumper Assembly

Shift Lever
REMOVING
REMOVING
1. Remove the E-clip securing the shift rod to the shift
lever.

www.mymowerparts.com

1. Remove the two flange bolts and lock nuts securing
the upper bumper supports to the bumper.
2. Remove the through-bolt and lock nut securing the
bumper to the frame; then remove the bumper.
8-11

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
CLEANING AND INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Clean all bumper components with parts-cleaning
solvent.
2. Inspect all welds for cracking or bending.
INSTALLING
1. Place the front bumper assembly into position and
install the through-bolt. Start the lock nut and finger-tighten only.
2. Install the two flange bolts and lock nuts on the
upper supports. Tighten all hardware securely.

FI467

3. Remove the storage compartment box; then remove
the seat.

Front Body Panel/Side
Panels
REMOVING
1. Remove the reinstallable rivets securing the radiator
access cover and remove the cover; then remove four
reinstallable rivets securing the steering post cover
and remove the cover.
FI468

4. Remove the ignition switch retaining ring and two
reinstallable rivets securing the instrument pod; then
remove the instrument pod.

FI465A

FI463A

FI466A

2. Unlock the storage compartment lid; then slide the
storage compartment cover assembly forward and
lift off the storage compartment.
FI464A

8-12

www.mymowerparts.com

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
5. Remove the cap screws and lock nuts securing the
front rack to the frame; then remove the front rack.
Account for the grommets and bushings.

CD779

FI469A

6. Remove the side panels by pulling on them to release
the tabs from the body; then remove the screws
securing the rear of the front panel to the frame.

CD780A

8. Disconnect four headlight connectors and secure the
wires out of the way; then disconnect the wires to the
front accessory plug.

CF237A

8
CD681

FI470A

9. Rotate the handlebar to the full-left position; then lift
and slide the panel to the rear and lift the rear up to
clear the handlebar.

7. Remove the left and right footwells; then remove the
shift knob. Remove the shift lever pivot axle nut and
remove the axle and shift lever. Account for a spring
and two O-rings.

CD765A

www.mymowerparts.com

8-13

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
NOTE: It may be necessary to rotate the body panel
to the right to align the opening with the handlebar.

CLEANING AND INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Clean all fender components with warm soap and
water.
2. Inspect fenders for cracks and/or loose rivets.
3. Inspect for any missing decals.
FI470A

INSTALLING
1. Rotate the handlebar to the full-left position; then
place the front body panel over the handlebar and
rotate and lower into position.

6. Install the shift lever spring, shift lever, and pivot
axle; then tighten the axle nut securely.

CD779
CD765

2. Connect the headlight connectors to the appropriate
headlights and the front accessory plug wires to the
accessory plug.

7. Install the instrument pod and ignition switch; then
secure with two reinstallable rivets and the ignition
switch retaining ring.
8. Set the storage compartment box into position; then
install the storage compartment cover making sure
the mounting tabs engage the slots. Slide rearward to
secure and lock by engaging the lid lock.

CD681

3. Make sure the rubber grommets and bushings are in
place; then place the front rack into position and
secure with the cap screws and lock nuts. Tighten
securely.
4. Install the footwells and foot rests. Tighten securely.
5. Install the cap screws securing the front body panel
to the frame and rear panel.

8-14

www.mymowerparts.com

FI468

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

FI467

CD691A

9. Install the steering post cover and secure with the
reinstallable rivets; then install and secure the radiator access panel.

2. Remove the screws securing the foot pegs to the
footrests; then remove the foot pegs and footwells.
3. Remove the cap screws and flange nuts securing the
footrests to the frame; then remove the footrests.
CLEANING AND INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Clean the footrest in parts-cleaning solvent.
2. Inspect the footrest weldments for cracks or unusual
bends.
3. Inspect all tubing for cracks or unusual bends.
FI466A

INSTALLING
1. Secure the footrests to the frame with four cap
screws and two flange nuts; then tighten the 8 mm
hardware to 20 ft-lb and the 10 mm hardware to 40
ft-lb.
2. Place the footwells onto the footrests; then put the
foot pegs in position and secure with two cap screws.
3. Install the machine screws and flange nuts securing
the front and rear fenders to the footwells.

Belly Panel
FI465A

10. Install the side panels.
REMOVING/INSTALLING

Footrests
REMOVING
1. Remove the machine screws and flange nuts securing the front and rear fenders to the footwells.

www.mymowerparts.com

1. Remove the machine screws and shoulder washers
securing the belly panel to the underside of the
frame; then remove the belly panel.
2. Place the belly panel into position on the underside
of the frame; then install the machine screws and
shoulder washers. Tighten securely.

8-15

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Exhaust System
REMOVING MUFFLER
1. Remove the two exhaust springs at the muffler/exhaust pipe juncture.

CD691A

3. Remove two machine screws securing the battery
cover and remove the cover.

CF138A

2. Slide the muffler rearward to clear the mounting lugs
and remove the muffler.
INSPECTING MUFFLER
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Inspect muffler externally for cracks, holes, and
dents.
2. Inspect the muffler internally by shaking the muffler
back and forth and listening for rattles or loose debris
inside the muffler.
NOTE: For additional details on cleaning the muffler/spark arrester, see Section 2.

INSTALLING MUFFLER
1. Place the muffler into position engaging the mounting lugs into the grommets; then slide the muffler
forward.
2. Install the two exhaust springs.

Rear Body Panel/Rack
REMOVING
1. Remove the cap screws and lock nuts securing the
rear rack; then remove the rear rack. Account for the
bushings.
2. Remove one shoulder screw and lock nut and three
plastic rivets (on each side) securing the rear body
panel to the footwells.

8-16

www.mymowerparts.com

CD687A

4. Disconnect the battery (negative cable first); then
remove the battery.
5. Disconnect the taillight/brakelight; then remove the
gas tank cap and lift off the rear body panel. Install
the gas tank cap.
NOTE: If the front body panel has not been
removed, the left-side and right-side panels and the
two machine screws must be removed (see Front
Body Panel/Side Panels in this section).

CLEANING AND INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

1. Clean all rear body panel components with warm
soap and water.
2. Inspect side panels and rear body panel for cracks
and loose rivets.
3. Inspect threaded areas of all mounting bosses for
stripping.
4. Inspect for missing decals.
INSTALLING
1. Remove the gas tank cap and set the rear body panel
in position; then install the cap and connect the taillight/brakelight connector.

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
2. Place the rear rack in position with the bushings and
secure with the cap screws and lock nuts. Tighten
securely.
3. Install one shoulder screw and three plastic rivets (on
each side) to secure the front of the rear body panel
to the footwells.

Taillight Assembly
REMOVING
1. Unplug the three-prong connector and free the taillight wiring harness from the frame.
2. Remove the torx-head cap screws securing the taillight assembly to the frame. Account for any washers.
3. Remove the taillight assembly.
INSPECTING
NOTE: Whenever a part is worn excessively,
cracked, or damaged in any way, replacement is necessary.

CD691

4. Place the battery into the battery box; then connect
the battery (positive cable first) and secure with the
battery cover.

1. Inspect wiring harness, three-prong connector, lens,
base, cap screws, and socket for damage.
2. Inspect all wires for corroding, pinching, and cracking.
3. Inspect the bulb for wattage, voltage, and proper
operation.
INSTALLING
1. Place the assembly into position on the frame and
secure with torx-head cap screws and any washers.
2. Tighten the cap screws securely.
3. Route the wiring harness over the rear frame; then
connect the three-prong connector.

CD687A

5. Secure the front and rear panels with two machine
screws; then install the left and right side panels.
NOTE: If the front body panel has not been
installed, see Front Body Panel/Side Panels in this
section.

6. Place the seat into position making sure it locks
securely.

www.mymowerparts.com

Seat
REMOVING/INSTALLING
1. To remove the seat, lift up on the latch release
(located at the rear of the seat). Raise the rear of the
seat and slide it rearward.
2. To lock the seat into position, slide the front of the
seat into the seat retainers and push down firmly on
the rear of seat. The seat should automatically lock
into position.

8-17

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

Troubleshooting
Problem: Handling too heavy or stiff
Condition
1.
2.
3.
4.
5.

Front wheel alignment incorrect
Lubrication inadequate
Tire inflation pressure low
Tie rod ends seizing
Linkage connections seizing

Problem: Steering oscillation
Condition
1.
2.
3.
4.
5.
6.
7.
8.

Tires inflated unequally
Wheel(s) wobbly
Wheel hub cap screw(s) loose - missing
Wheel hub bearing worn - damaged
Tie rod ends worn - loose
Tires defective - incorrect
A-arm bushings damaged
Bolts - nuts (frame) loose

Problem: Steering pulling to one side
Condition
1.
2.
3.
4.
5.

Tires inflated unequally
Front wheel alignment incorrect
Wheel hub bearings worn - broken
Frame distorted
Shock absorber defective

Problem: Tire wear rapid or uneven
Condition
1. Wheel hub bearings worn - loose
2. Front wheel alignment incorrect
3. Tire inflation pressure incorrect

Problem: Steering noise
Condition
1. Cap screws - nuts loose
2. Wheel hub bearings broken - damaged
3. Lubrication inadequate

8-18

www.mymowerparts.com

Remedy
1.
2.
3.
4.
5.

Adjust alignment
Lubricate appropriate components
Adjust pressure
Replace tie rod ends
Repair - replace connections

Remedy
1.
2.
3.
4.
5.
6.
7.
8.

Adjust pressure
Replace wheel(s)
Tighten - replace cap screws
Replace bearing
Replace - tighten tie rod ends
Replace tires
Replace bushings
Tighten bolts - nuts

Remedy
1.
2.
3.
4.
5.

Adjust pressure
Adjust alignment
Replace bearings
Repair - replace frame
Replace shock absorber

Remedy
1. Replace bearings
2. Adjust alignment
3. Adjust pressure

Remedy
1. Tighten cap screws - nuts
2. Replace bearings
3. Lubricate appropriate components

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Modify Date                     : 2011:08:18 08:20:15-05:00
Create Date                     : 2011:08:16 16:40:29-05:00
Metadata Date                   : 2011:08:18 08:20:15-05:00
Creator Tool                    : FrameMaker 8.0
Format                          : application/pdf
Title                           : untitled
Document ID                     : uuid:7523c659-f5e9-4081-96cf-5e8e4ea18159
Instance ID                     : uuid:15b91278-25db-4336-af1e-673b68d90260
Producer                        : Acrobat Distiller 9.4.5 (Windows)
Page Layout                     : SinglePage
Page Mode                       : UseOutlines
Page Count                      : 210
Creator                         : FrameMaker 8.0

EXIF Metadata provided by EXIF.tools

Arctic_cat_2012_450_1000_service_manual Arctic Cat 2012 450 1000 Service Manual

Navigation menu

Versions of this User Manual:

Views

Navigation