C More Hardware User Manual Getting Started Chapter 1 Ch1

User Manual: Chapter 1 C-more (EA9 Series) Touch Panel User Manual and Product Inserts

Open the PDF directly: View PDF .
Page Count: 16

Download
Open PDF In Browser	View PDF

Getting Started

Chapter

1

In This Chapter...
Introduction�������������������������������������������������������������������������������������������������������������������1-2
The Purpose of this Manual������������������������������������������������������������������������������������������1-2
Supplemental Manuals�������������������������������������������������������������������������������������������������1-2
Technical Support��������������������������������������������������������������������������������������������������������1-2
Conventions Used����������������������������������������������������������������������������������������������������������1-3
Key Topics for Each Chapter�����������������������������������������������������������������������������������������1-3
Product Overview����������������������������������������������������������������������������������������������������������1-4
Quick Start Steps�����������������������������������������������������������������������������������������������������������1-5
Step 1 – Unpack and Inspect����������������������������������������������������������������������������������������1-5
Step 2 – Install Optional Hardware Accessories�������������������������������������������������������������1-6
Step 3 – Become Familiar with Available Communication Ports������������������������������������1-7
Step 4 – Install the Programming Software and Develop a Project�������������������������������1-8
Step 5 – Connect Touch Panel to Computer����������������������������������������������������������������1-9
Step 6 – Provide Power to the Touch Panel����������������������������������������������������������������1-10
Step 7 – Access the Touch Panel Setup Screens���������������������������������������������������������1-12
Step 8 – Choose Touch Panel to Device Protocol & Cables����������������������������������������1-13
Step 9 – Connect Touch Panel to PLC������������������������������������������������������������������������1-16

Chapter 1 - Getting Started

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D

Introduction

1-2

The Purpose of this Manual
Thank you for purchasing our C-more® Touch Panel family of products. This manual
describes AutomationDirect.com’s C-more Touch Panels, their specifications, included
components, available accessories and provides you with important information for
installation, connectivity and setup. The manual shows you how install, wire and use the
products. It also helps you understand how to interface the panels to other devices in a
control system.
This user manual contains important information for personnel who will install the touch
panels and accessories, and for the personnel who will be programming the panel. If you
understand control systems that make use of operating interfaces such as the C-more touch
panels, our user manuals will provide all the information you need to get, and keep your
system up and running.

Supplemental Manuals
If you are familiar with industrial control type devices, you may be able to get up and running
with just the aide of the Quick Start Guide that is included with each touch panel. You can
also refer to the On-line help that is available in the C-more programming software for more
information about programming the panel.

Technical Support
We strive to make our manuals the best in the industry. We rely on your feedback to let
us know if we are reaching our goal. If you cannot find the solution to your particular
application, or, if for any reason you need technical assistance, please call us at:
				770–844–4200
Our technical support group will work with you to answer your questions. They are available
Monday through Friday from 9:00 A.M. to 6:00 P.M. Eastern Time. We also encourage you
to visit our web site where you can find technical and non-technical information about our
products and our company.
			http://c-more.automationdirect.com

®

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

Chapter 1 - Getting Started

Conventions Used
When you see the “notepad” icon in the left-hand margin, the paragraph to its immediate right will be a special note.
The word NOTE: in boldface will mark the beginning of the text.

When you see the “exclamation mark” icon in the left-hand margin, the paragraph to its immediate
right will be a warning. This information could prevent injury, loss of property, or even death (in
extreme cases). The word Warning: in boldface will mark the beginning of the text.

Key Topics for Each Chapter
The beginning of each chapter will list the key topics
that can be found in that chapter.
Getting Started

CHAPTER

1

In This Chapter...
General Information .................................................................1-2
Specifications ...........................................................................1-4

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

®

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D

1-3

Chapter 1 - Getting Started

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D

Product Overview

1-4

Some of the features designed into the product to provide excellent hardware and software are
listed below.
• Analog touch screen (no touch cell boundaries). The touchscreen is designed to respond to a single
touch. If it is touched at multiple points at the same time, an unexpected object may be activated.
• Plenty of memory and methods to get data in/out of the panel
• Overlapping active devices on the touch screen
• 65,536 colors for enhanced graphics
• Screen resolutions up to 1024 X 768 pixel
• HDMI Video Output on 12-inch and 15-inch models.
• Built-in FTP client/server, E-mail client, and Web server
• Audio output port - stereo, requires amplifier and speaker(s) (full feature units only)
• User configurable LED on the front of the panel
• Built-in project simulation; test on PC while developing
• Ethernet 10/100Base-T communications (not available on EA9-T6CL-R)
• 15 pin serial port with RS-232, RS422/485
• 3-wire terminal block RS-485 port and RJ12 RS-232 port (full feature units only)
• Programming via USB or Ethernet (Ethernet not available on EA9-T6CL-R)
• Optional AC/DC power adapter (EA-AC)
• Animation of bitmaps and objects
• Thousands of built-in symbols and Windows fonts
• PID face plate, trending, alarming and a recipe database
• Event Manager to trigger actions based on assigned state changes, schedules, PLC tag names, etc.
setup in a database environment. The event can also trigger a sound byte, initiate a screen capture,
send a data file (FTP), send an E-mail, etc.
• Trend Data logging
• Internet Remote Access
• Customizable label on the front of the panel

®

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

Chapter 1 - Getting Started

Quick Start Steps
Step 1 – Unpack and Inspect
a.) U
 npack the C-more Touch Panel from its shipping carton. Included in the carton are the
following:
• C-more Touch Panel
• cutout template
• mounting clips
• DC power connector
• gasket
• logo label
• Quick Start Guide

b.) Unpack any accessories that have
been ordered, such as: AC/DC
Power Adapter, programming cable,
communications cable, etc.

Quick Start
Guide

Cutout Template*

c.) Inspect all equipment for
completeness. If anything is missing
or damaged, immediately call
the AutomationDirect® returns
department @ 1-800-633-0405.

C-more Panel
Gasket
DC power connector
Mounting Clips

Logo Label*

*Not included with EA9-T7CL-R and EA9-T7CL.

Shipping Carton Contents
Optional Accessories
AC Power Adapter
EA-AC

USB Pen Drive
USB-FLASH

Protective Screen Cover
EA-x-COV2

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

®

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D

1-5

Chapter 1 - Getting Started

Step 2 – Install Optional Hardware Accessories

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1-6

EA-AC
AC / DC Power Adapter

EA-x-COV2
Screen Protector

EA-COMCON-3A
DSUB Port Adapter

EA-SD-CARD
SD Card

C-more Touch Panel

®

USB-FLASH
USB Pen Drive

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

Chapter 1 - Getting Started

Step 3 – Become Familiar with Available Communication Ports
Port 2
Serial Communication
RS-485
+
–
Logic Ground

SD Card Slot 1

SD Card Slot 2

Port 3
RJ12 Serial Communication
RS-232C
Pin

Signal

1

0V

2

N.C.

3

RXD

4

TXD

5

Supplies +5VDC

1

N.C.

2

1

6

0V

2

D–

3

4

3

D+

4

GND

1

6

USB Port - Type B
Programming
Pin

Signal

Shell Shield

HDMI Port Video Out

Port 1
PLC Serial Communications
RS-232C / RS-485

Signal

Pin

Signal

1

15

9

Pin

Frame GND

6

LE (for DH485)

11 TXD+ (422/485)

2

TXD (232C)

7

CTS (232C)

12 TXD– (422/485)

3

RXD (232C)

8

RTS (232C)

13 Term. Resistor

4

VCC
(Supplies +5VDC)

9

RXD+ (422/485)

14 N.C.

5

Logic GND

10 RXD– (422/485)

15 N.C.

Pin

Signal

1

USB Port - Type A
USB Device Options

Ethernet 10/100 Base-T
PLC Communications,
Programming/Download
Signal

Pin

TD+

5

do not use

2

TD–

6

RD–

3

RD+

7

N.C.

4

do not use

8

N.C.

Link Status LED (Green)
On

Pin

Signal

1

1 2 3 4

Pin

8

Vbus

2

D–

3

D+

4

GND

SHELL Shield

Network Speed LED (Yellow)

Ethernet Linked

On

100M

Off No Ethernet Comm.

Off

10M

Blinking Comm. Activity
Green

Signal

1

1

8

Note: Device is not available on Base Feature touch panel EA9-T6CL-R
Note: Device is not available on Base Feature touch panels EA9-T7CL-R and EA9-T15CL-R
Note: Device is only available on touch panels EA9-T12CL and EA9-T15CL.
Note: Device is only available on touch panels EA9-T12CL, EA9-T15CL and EA9-T15CL-R.

NOTE: See Chapter 2: Specifications and Chapter 6: PLC Communications for additional details on the available
communication ports, protocols and cables.

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

®

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1-7

Chapter 1 - Getting Started

Step 4 – Install the Programming Software and Develop a Project

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1-8

Following are the minimum system requirements for running C-more Programming
Software, p/n EA9-PGMSW, on a PC:
• Keyboard and Mouse or compatible pointing device
• Super VGA color video adapter and monitor with at least 800 x 600 pixel resolution (1024 x
768 pixel recommended) 64K color minimum
• 300 MB free hard-disk space
• CD-ROM or DVD drive for installing software from the CD
• USB port or Ethernet 10/100 Mbps port for project transfer from software to touch panel
(Ethernet port not available on EA9-T6CL-R)
• Operating System - Windows 7, 8, 8.1 and 10 (32 or 64bit)

Insert the supplied CD into the PC’s CD drive and follow the instructions. If you need
assistance during the software installation, call the AutomationDirect Technical Support team
@ 770-844-4200.
NOTES: Regarding Ethernet access to a C-more panel.
If you intend to take advantage of the methods of remote access to the panel, including the web server, PC remote
access, FTP, iOS or Android app, you need to consider the security exposure in order to minimize the risks to your
process and your C-more panel.
Security measures may include password protection, changing the ports exposed on your network, including a VPN
in your network, and other methods. Security should always be carefully evaluated for each installation. Refer to
Appendix C - Security Considerations for Control Systems Networks.

®

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

Chapter 1 - Getting Started

Step 5 – Connect Touch Panel to Computer
• Connect a USB Programming Cable, such as p/n USB-CBL-AB15, from a USB type A port on the
PC to the USB type B programming port on the C-more touch panel
• or connect the C-more touch panel and PC together either directly or via an Ethernet switch, and
CAT5 Ethernet cables (full feature panels only)
C-more
Touch Panel

PC

USB
Port
USB-CBL-ABxx
USB Cable

USB
Port

Stride™
Ethernet Switch
10/100 Base-T

PC

(such as SE2-SW5U)

Ethernet
Port

C-more
Touch Panel

Ethernet CAT5
Cable

Auto MDI / MDI-X
Ethernet Port

PC
C-more
Touch Panel
Ethernet
Port

Ethernet CAT5
Cable
Auto MDI / MDI-X
Ethernet Port

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

®

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D

1-9

Chapter 1 - Getting Started

Step 6 – Provide Power to the Touch Panel

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D

• Connect a dedicated 12-24 VDC Class 2 power supply to the DC connector on the rear of the
C-more touch panel, include wiring the ground terminal to a proper equipment ground
• or install a C-more AC/DC Power Adapter, EA-AC, to the rear of the touch panel and connect an
AC voltage source of 100-240 VAC, 50/60Hertz, to its AC connector (see note below)
• then turn on the power source and check the LED status indicators on the front and rear of the
C-more touch panel for proper indication (see next page)
NOTE: A dedicated power supply is recommended. If the power supply also feeds inductive loads such as
solenoids or relays, the transients caused by these loads can affect the operation of the panel or damage panel
components.
NOTE: The AC/DC Power Adapter, EA-AC, is for C-more touch panels only. The adapter is powered from a 100240 VAC, 50/60 Hertz power source. The adapter provides 24 VDC @ 1.5 A. Power Fault features help protect data
on an SD memory card during power failures.

AC Wiring

DC Wiring

Recommended DC Supply Fuse
Panel Size Rating
6“ – 10”
2.5 A
12“ & 15”

4.0 A

ADC p/n
MDL2-5
MDL4

+

12-24 VDC

–

Recommended AC Supply Fuse
3.0A time delay, ADC p/n: MDL3

GND

L

Equipment
Ground

100 - 240 VAC
50 / 60 Hz
N

G

DC-CON Tightening Torque
Power connector screw torque
Power connector mounting torque

1-10

70.4 oz-in (0.5 Nm)
56 oz-in (0.4 Nm)

Tightening Torque
Power supply cable torque
71 - 85 oz-in (0.5 - 0.6 Nm)
Power connector mounting torque 71 - 85 oz-in (0.5 - 0.6 Nm)
Mounting flange screw torque
57 - 71 oz-in (0.4 - 0.5 Nm)

Warning: Use 60 / 75­°C copper conductors only.

®

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

Chapter 1 - Getting Started

Step 6 – Provide Power to the Touch Panel (cont’d)
C-more LED Status Indicators

User Defined LED (Green, Orange & Red)
Off

Power LED (Green)

Green
Red
Orange
Blinking
Red
Blinking
Orange
Blinking
Green

User Defined
(Refer to online help
file for further details)

On

Power On

Off

Power Off

Front View
CPU Status LED (Green, Orange & Red)
Off
Green
Red
Blinking
Red
Blinking
Orange
Blinking
Green

Power Off
Normal – CPU Run State

CPU

Memory Error

Port2
TxD
RxD

Watchdog Timer Error
OS Error
Power Loss Detection

Port3
TxD
RxD

Port1 RxD

TxD

Serial TxD/RxD LED (Green)
On Comm. is active
Off No communication

Rear View

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

®

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1-11

Chapter 1 - Getting Started

Step 7 – Access the Touch Panel Setup Screens

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1-12

• Access the Main Menu of the touch panel System Setup Screens by pressing the extreme upper left
corner of the panel display area for three (3) seconds as shown below.
• Adjust the time and date for the panel by pressing the Setting button on the Main Menu, then press
the Adjust Clock button on the Setting screen.
• Use the right pointing arrows for the time or date display to select the unit to change. Use the up
and down arrows to increment or decrement the value for the selected unit.
• Press OK when done to accept the changes to the time and date in the touch panel or press Cancel
to exit the Adjust Clock setup screen without making any changes.
• Press the Main Menu button on the Setting screen and then the Exit button on the Main Menu
screen to return to the application screen.

			

®

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

Chapter 1 - Getting Started

Step 8 – Choose Touch Panel to Device Protocol & Cables
Compatibility Table
Model

Protocols
Productivity Series
Do-more

all

CLICK

DL05/DL06

all
H0-ECOM/H0-ECOM100
all
D2-230

DL105

D2-240

DL205

D2-250/D2-250-1/D2-260
D2-240/D2-250-1/D2-260
Using DCM
H2-ECOM/H2-ECOM100
D3-330/330P (Requires the use of a Data Communications Unit)
D3-340

AutomationDirect

D3-350

DL305

D3-350 DCM
D4-430
D4-440
DL405

D4-450

All with DCM
H4-ECOM/H4-ECOM100
H2-WinPLC (Think & Do) Live V5.2 or later and Studio any version
H2-WinPLC (Think & Do) Live V5.5.1 or later and Studio V7.2.1 or later
GS Drives
SOLO Temperature Controllers

Productivity Serial
Productivity Ethernet
Do-more Serial
Do-more Ethernet
Modbus (CLICK)
K-Sequence
Direct NET
Modbus (Koyo addressing)
Direct LOGIC Ethernet
K-Sequence
K-Sequence
K-Sequence
Direct NET
K-Sequence
Direct NET
Modbus (Koyo addressing)
Direct NET
Modbus (Koyo addressing)
Direct LOGIC Ethernet
Direct NET
Direct NET
K-Sequence
Direct NET
Modbus (Koyo addressing)
Direct NET
Modbus (Koyo addressing)
K-Sequence
Direct NET
K-Sequence
Direct NET
K-Sequence
Direct NET
Modbus (Koyo addressing)
Direct NET
Modbus (Koyo addressing)
Direct LOGIC Ethernet
Think & Do Modbus RTU (serial port)
Think & Do Modbus TCP/IP (Ethernet port)
GS Drives Serial
GS Drives TCP/IP (GS-EDRV)
SOLO Temperature Controller

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

®

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D

1-13

Chapter 1 - Getting Started

Step 8 – Choose Touch Panel to Device Protocol & Cables (cont’d)

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D

Compatibility Table (cont’d)
Model

Protocols
MicroLogix 1000, 1100, 1200, 1400, 1500, SLC 5-01/02/03

DH485/AIC/AIC+

MicroLogix 1000, 1100, 1200, 1400 and 1500
SLC 5-03/04/05

DF1 Half Duplex; DF1 Full Duplex

ControlLogix™, CompactLogix™, FlexLogix™

Allen-Bradley

PLC-5

DF1 Full Duplex

ControlLogix, CompactLogix, FlexLogix - Tag Based

DF1 Half Duplex; DF1 Full Duplex

ControlLogix, CompactLogix, FlexLogix - Generic I/O Messaging

EtherNet/IP Server

ControlLogix, CompactLogix, FlexLogix - Tag Based
MicroLogix 1100, 1400 and SLC 5/05, via native Ethernet port

EtherNet/IP Client

MicroLogix 1000, 1100, 1200, 1400, 1500, SLC 5-03/04/05, all via ENI adapter

GE

Mitsubishi

Modicon

90/30, 90/70. Micro 90, VersaMax Micro

SNPX

90/30, Rx3i

SRTP Ethernet

FX Series

FX Direct

Q02, Q02H, Q06H, Q12H, Q25H

Q CPU

Q, QnA Serial

QnA Serial

Q, QnA Ethernet
QnA Ethernet
984 CPU, Quantum 113 CPU, AEG Modicon Micro Series 110 CPU: 311-xx, 411-xx,
Modbus RTU
512-xx, 612-xx
Modbus RTU
Other devices using Modicon Modbus addressing
TUModbus TCP/IP
C200 Adapter, C500

Omron

CJ1/CS1 Serial
CJ1/CS1 Ethernet

Siemens

1-14

Host Link
FINS

S7-200 CPU, RS-485 Serial

PPI

S7-200 CPU, S7-300 CPU, S7-1200 CPU; Ethernet

Ethernet ISO over TCP

®

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

Chapter 1 - Getting Started

Step 8 – Choose Touch Panel to Device Protocol & Cables (cont’d)
Available cables to connect from PLC to C-more serial Port 1
Purchased Cable
Description

Cable
Part Number

AutomationDirect Productivity Series, Do-more, CLICK,
Direct LOGIC PLC RJ-12 port, DL05, DL06, DL105, EA-2CBL
DL205, D3-350, D4-450 & H2-WINPLC (RS-232C)
Direct LOGIC (VGA Style) 15-pin port
DL06, D2-250 (250-1), D2-260 (RS-232C)

EA-2CBL-1

Direct LOGIC PLC RJ-11 port, D3-340 (RS-232C)

EA-3CBL

Direct LOGIC DL405 PLC 15-pin D-sub port,
DL405 (RS-232C)

EA-4CBL-1

Direct LOGIC PLC 25-pin D-sub port, DL405, D3-350,
EA-4CBL-2
DL305 DCU and all DCM’s (RS-232C)
Allen-Bradley MicroLogix 1000, 1100, 1200, 1400,
1500 (RS-232C)

EA-MLOGIX-CBL

Allen-Bradley SLC 5-03/04/05, ControlLogix,
CompactLogix, FlexLogix DF1 port (RS-232C)

EA-SLC-232-CBL

Allen-Bradley PLC-5 DF1 port (RS-232C)

EA-PLC5-232-CBL

Allen-Bradley MicroLogix, SLC 5-01/02/03, PLC5
DH485 port (RS-232C)

EA-DH485-CBL

GE 90/30, 90/70, Micro 90, VersaMax Micro
15-pin D-sub port (RS-422A)

EA-90-30-CBL

MITSUBISHI FX Series 25-pin port (RS-422A)

EA-MITSU-CBL

MITSUBISHI FX Series 8-pin mini-DIN (RS-422A)

EA-MITSU-CBL-1

OMRON Host Link (C200 Adapter, C500) (RS-232C)

EA-OMRON-CBL

NOTE: The above list of pre-made communications cables may be purchased. See Chapter 6: PLC
Communications for wiring diagrams of additional user constructed cables. Chapter 6 also includes wiring diagrams
for the pre-made cables.

EA-2CBL

EA-2CBL-1

Pre-made cable		
examples

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E

®

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D

1-15

Chapter 1 - Getting Started

Step 9 – Connect Touch Panel to PLC

1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1-16

• Connect the serial communications cable between the C-more touch panel and the PLC
• or connect the C-more touch panel and PLC together either directly or via an Ethernet switch, and
CAT5 Ethernet cables (full feature panels only)

Serial
C-more
Touch Panel
DL-06 PLC

EA-2CBL-1
Port 2

Port 1

Ethernet via Switch
Stride™
Ethernet Switch
10/100 Base-T

(such as SE2-SW5U)

H0-ECOM/H0-ECOM100
Ethernet Module

Ethernet CAT5
Cable
DL06 PLC

C-more
Touch Panel

Auto MDI / MDI-X
Ethernet Port

Ethernet
H0-ECOM/H0-ECOMM100
Ethernet Module

DL06 PLC

®

Ethernet CAT5
Cable

C-more
Touch Panel

Auto MDI / MDI-X
Ethernet Port

EA9-USER-M Hardware User Manual, 1st Ed. Rev. E



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Language                        : en-US
XMP Toolkit                     : Adobe XMP Core 5.6-c138 79.159824, 2016/09/14-01:09:01
Format                          : application/pdf
Title                           : C-more Hardware User Manual Getting Started
Creator                         : AutomationDirect
Create Date                     : 2017:11:06 14:03:48-05:00
Metadata Date                   : 2017:11:06 14:04:27-05:00
Modify Date                     : 2017:11:06 14:04:27-05:00
Creator Tool                    : Adobe InDesign CC 2017 (Windows)
Instance ID                     : uuid:9abc9921-d4cd-4d5a-8639-2fd05fb52458
Original Document ID            : xmp.did:AC8300A79C14E311B497E908AC6DEAF6
Document ID                     : xmp.id:e898c545-51b1-994f-b3eb-431aeb37e78c
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:e65c25ef-f4a8-164d-9309-b221cbe664d3
Derived From Document ID        : xmp.did:7EA195A7CB14E311B497E908AC6DEAF6
Derived From Original Document ID: xmp.did:AC8300A79C14E311B497E908AC6DEAF6
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Windows)
History Changed                 : /
History When                    : 2017:11:06 14:03:48-05:00
Authors Position                : C-more Hardware User Manual
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 16
Author                          : AutomationDirect

EXIF Metadata provided by EXIF.tools