CI2+ Operation Manual Steinberger CI2 Plus Ci2plus (English) A0 En Om
Steinberger CI2 Plus ci2plus (English) Operation Manual a0 ci2plus_en_om_a0 Steinberger - CI2 Plus - ci2plus (English) Operation Manual a0
Steinberger CI2 Plus ci2plus (English) Operation Manual a0 ci2plus_en_om_a0 Steinberger - CI2 Plus - ci2plus (English) Operation Manual a0
User Manual: Steinberger CI2 Plus ci2plus (English) Operation Manual a0 Steinberger - CI2 Plus - ci2plus (English) Operation Manual a0
Open the PDF directly: View PDF 
.
Page Count: 32
| Download | |
| Open PDF In Browser | View PDF |
USB AUDIO INTERFACE EN DE FR ES IT JA FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/ reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B) COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Address : Telephone : Type of Equipment : Model Name : Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620 714-522-9011 USB AUDIO INTERFACE CI2+ This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See user manual instructions if interference to radio reception is suspected. * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. 2 CI2+ Operation Manual (FCC DoC) English PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Do not open Water warning • Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel. • Do not expose the device to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings. If any liquid such as water seeps into the device, unplug the USB cable from this device immediately. Then have the device inspected by qualified Yamaha service personnel. • Never insert or remove a USB cable with wet hands. Fire warning • Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: Location Connections • Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration or damage to the internal components. • Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the device, TV, or radio may generate noise. • Do not place the device in an unstable position where it might accidentally fall over. • Before moving the device, remove all connected cables. (3)-13 • Before connecting the device to other electronic components, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum. Also, be sure to set the volumes of all components at their minimum levels and gradually raise the volume controls while playing the device to set the desired listening level. Maintenance • When cleaning the device, use a soft, dry cloth. Do not use paint thinners, solvents, cleaning fluids, or chemicalimpregnated wiping cloths. 1/2 CI2+ Operation Manual 3 Handling caution English • When turning on the AC power in your audio system, always turn on monitor speakers LAST, to avoid speaker damage. When turning the power off, monitor speakers should be turned off FIRST for the same reason. • Do not insert a finger or hand in any gaps on the device. • Never insert or drop paper, metallic, or other objects into the gaps on the panel. If this happens, unplug the USB cable from this device immediately. Then have the device inspected by qualified Yamaha service personnel. • Do not place vinyl, plastic or rubber objects on the device, since this might discolor the panel. • Do not rest your weight on, or place heavy objects on the device, and do not use excessive force on the buttons, switches or connectors. • Do not use the instrument/device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed. Always unplug the USB cable from a computer or turn off the computer to turn off the device when the device is not in use. NOTICE • This manual is the exclusive copyrights of Yamaha Corporation. • Use of the software and this manual is governed by the license agreement which the purchaser fully agrees to upon breaking the seal of the software packaging. (Please read carefully the Software Licensing Agreement at the end of this manual before installing the application.) • Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. • Yamaha Corporation makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this manual and the software. • Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use. • Future upgrades of application and system software and any changes in specifications and functions will be announced separately. • The screen displays as illustrated in this manual are for instructional purposes, and may appear somewhat different from the screens which appear on your computer. • Steinberg and Cubase are the registered trademarks of Steinberg Media Technologies GmbH. (3)-13 4 CI2+ Operation Manual • This product incorporates and bundles computer programs and contents in which Steinberg Media Technologies GmbH and Yamaha Corporation owns copyrights or with respect to which it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES. • Windows is a registered trademark of Microsoft® Corporation in the United States and other countries. • Apple, Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries. • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. 2/2 Contents English Contents Introduction .........................................................................6 Features ................................................................................................................................6 Package Contents ........................................................................................................7 About the Included Disks .......................................................................................7 About the power supply ...........................................................................................8 The Controls and Connectors ........................................9 Front Panel .........................................................................................................................9 Rear Panel .....................................................................................................................13 Software Installation ..................................................... 14 Installing Cubase Essential ...............................................................................14 Installing TOOLS for CI2 .....................................................................................15 Connecting to an External Device ............................. 18 Connection Examples ............................................................................................18 Options ...............................................................................................................................18 Try it out ............................................................................ 19 Preparing for using the CI2+ with Cubase .........................................19 Recording .........................................................................................................................20 Editing .................................................................................................................................22 Troubleshooting .............................................................. 23 Uninstalling the TOOLS for CI2 .................................. 25 Appendix ........................................................................... 26 Input and Output Specifications ...................................................................26 General Specifications ..........................................................................................26 License Agreement for TOOLS for CI2 .................................................27 CI2+ Operation Manual 5 Introduction Introduction English Thank you for your purchase of the USB AUDIO INTERFACE CI2+. Using Cubase, the CI2+ is a highly intuitive, indispensable aid in recording, editing and sound shaping. Simply connect the CI2+ to your computer via USB, and you’ve got a comprehensive control center and seamless environment for complete music production with Cubase. Please read the Operation Manual (this book) so that you can take full advantage of its superlative features and enjoy trouble-free operation for years to come. Also keep it in a safe place for future reference. Features USB bus-powered The CI2+ can be simply connected to a USB terminal on your computer and can operate on USB bus power. Phantom power (+48V) can be used With the [ACTION PAD] button (or an optional Yamaha FC5 foot switch as an alternative), you can use the Interactive Recording function on Cubase. The Interactive Recording function provides easy and quick recording. Phantom power can be supplied to two analog input jacks (XLR type). Controlling Cubase Compatible with Core Audio (Mac OS X) and ASIO/WDM (Windows) Using with a Core Audio/ASIO compatible DAW software application such as Cubase helps to reduce latency (sound delay). Cubase Essential DAW Software Supplied Cubase Essential software, included in this package, offers versatile, high-performance hard-disk recording capability. Quick access to Cubase with the Browse mode The Browse mode helps to create new projects and new tracks quickly on Cubase. 6 Quick recording with the Interactive Recording function CI2+ Operation Manual The AI KNOB can control a desired parameter within the principal window and plug-in software on Cubase, specified via the mouse pointer. Also, the [PLAY/STOP] button, [REC] button, [PREVIOUS] button, and [NEXT] button can control the transport functions such as Play and Record on Cubase. Introduction The CI2+ package contains the following items. After opening the CI2+ package, make sure that it includes all of the items listed below. • CI2+ • CI2+ Operation Manual (this book) • TOOLS for CI2 CD-ROM • Cubase Essential DVD-ROM • USB-eLicenser (USB protection device) • ESSENTIAL PRODUCT LICENSE INFORMATION card About the Included Disks English Package Contents Disk Contents Each of the included disks contains the following software (driver). TOOLS for CI2 CD-ROM • TOOLS for CI2 Cubase Essential DVD-ROM • Cubase Essential • USB cable • Ferrite core Special Notices NOTE The manual of Cubase Essential is a PDF file which can be opened from the [Help] menu on Cubase. To view PDF files, you need to install Adobe Reader on your computer. You can download the latest version of Adobe Reader at the following website. http://www.adobe.com/products/reader/ Precautions about the USBeLicenser and the ESSENTIAL PRODUCT LICENSE INFORMATION card CAUTION • The USB-eLicenser or the unused activation code on the ESSENTIAL PRODUCT LICENSE INFORMATION card represent the software application license. Losing the unused activation code or the USB-eLicenser once activated can be the same as losing your software product. • If the “USB-eLicenser” and “ESSENTIAL PRODUCT LICENSE INFORMATION card” are lost or stolen, Steinberg Media Technologies GmbH and Yamaha Corporation cannot reissue them. In this case, you will need to purchase the product again. CAUTION • Steinberg and Yamaha make no representations or warranties with regard to any problems while attempting to copy the disks or software and cannot be held responsible for the results of attempts to copy the data. • These disks are NOT for audio/visual purposes. Do not attempt to play the disks on a CD/DVD player. Doing so may result in irreparable damage to your audio CD/DVD player. IMPORTANT • Before breaking the seal of TOOLS for CI2 disk package, please read carefully the Software License Agreement on page 27 of this manual. By opening this disk package, you indicate your agreement with the use terms of the software and concurrence with the Software License Agreement. • The software (Yamaha Steinberg USB Driver, Steinberg CI2 Extension) included in the TOOLS for CI2 and the copyrights thereof are under exclusive ownership by Yamaha. • The software included in the Cubase Essential DVD-ROM and the copyrights thereof are under exclusive ownership by Steinberg Media Technologies GmbH. • Copying/reproduction of the software in whole or in part by any means is expressly forbidden without the written consent of the manufacturer. • For the latest information of the software contained in the accessory disk, please see the site below: Future upgrades of application and system software and any changes in specifications announced separately on the website. http://service.steinberg.de/goto.nsf/show/ supportupdates_ci2plus_gb CI2+ Operation Manual 7 Introduction English System Requirements for Software About the power supply The system requirements below are necessary for installing software included in the accessory disks (TOOLS for CI2 and Cubase Essential). Power supply Windows OS: Windows XP Professional (SP3)/ Windows XP Home Edition (SP3)/ Windows Vista (SP1 or later, 32-bit/64-bit*)/ Windows 7 (32-bit/64-bit*) CPU: 2GHz or more (dual core CPU recommended) Memory: 1GB or more Display Resolution: 1280 x 800 — full color Interface: Equipped with a USB terminal Hard Disk: Free disk space of 4GB or more; high-speed hard disk The power of the CI2+ is supplied only from the computer via a USB cable. A power cable is not necessary. Precautions when using the USB terminal Be sure to observe the following points when connecting to the computer’s USB interface. Failing to do so may result in the computer freezing or shutting down, as well as corruption or even loss of data. If the device or computer does freeze, restart the application or computer. NOTICE *Cubase Essential runs as a 32-bit application on Windows Vista 64-bit and Windows 7 64-bit. • Be sure to wake the computer from sleep/suspended/standby mode before making a connection to the computer’s USB terminal. Mac OS X • Always quit all applications running on the computer before connecting or disconnecting the USB cable. OS: Mac OS X 10.5.5 or later/ Mac OS X 10.6.x • When connecting or disconnecting the USB cable, be sure to set the MASTER control to the minimum. CPU: PowerPC G5 (Intel Core Duo CPU recommended) • Wait at least 6 seconds between connecting or disconnecting the USB cable. Memory: 1GB or more Display Resolution: 1280 x 800 — full color Interface: Equipped with a USB terminal Hard Disk: Free disk space of 4GB or more; high-speed hard disk NOTE NOTE To prevent electromagnetic interference, fasten the ferrite core to the USB cable near the USB terminal on the CI2+. USB cable • A DVD drive is required for installation. • Note that the system requirements may be slightly different from those described above depending on the particular operating system. • Downloading the license of Cubase Essential requires an Internet connection. • The audio input and output functions of the CI2+ also work properly on Mac OS X 10.4.11. Install TOOLS for CI2 to use the functions. 8 CI2+ Operation Manual USB terminal on the CI2+ Ferrite core The Controls and Connectors English The Controls and Connectors Front Panel 1 2 3 % ^ & ) 9 4 ! 8 @ 5 6 7 Mixer section Mixer section 1 [HI-Z INPUT 1] button This button switches the HI-Z on (O)/off (N) for the analog input jack 1. When directly connecting an electric guitar or electric bass that has passive pickups and no built-in preamp to the analog input jack 1, turn the [HI-Z] button on. NOTE • Use an unbalanced phone cable when you connect an electric guitar or electric bass and turn the [HI-Z] button on. If you use a balanced cable or an XLR cable in such a case, this device will not work correctly. • If no device is connected to analog input jack 1, turn this button off. Otherwise noise may occur. $ # AI KNOB section 2 [MONO] button This button allows analog input jacks 1 and 2 to be used either as separate mono channels or as a stereo pair. When the button is on (O), analog input jacks 1 and 2 function as independent mono channels feeding both the L and R LINE OUT jacks. It is used to monitor the sound of the microphone or guitar connected to the analog input jack 1 in the center of the monitor speakers. When the button is off (N), analog input jack 1 and 2 function as a stereo pair: the analog input jack 1 signal feeds the L LINE OUT jack and the analog input jack 2 signal feeds the R LINE OUT jack. Switching this button on/off does not affect the signal sent to the computer. CI2+ Operation Manual 9 The Controls and Connectors 3 INPUT 1/2 GAIN controls/PEAK Indicator English Adjusts the input signal level. The signal that has passed through the GAIN control will be sent to the computer. To achieve the best balance of the recording level between S/N ratio and dynamic range, adjust the level so that the PEAK Indicator lights only occasionally and briefly on the highest input transients. 4 [PHANTOM INPUT 1&2] button/ Indicator This button switches the phantom power (+48V) on (O)/off (N). If you turn the button on, the CI2+ supplies phantom power to the analog input jack 1 and 2 (XLR-type). The indicator lights when the button is turned on. Turn this button on when using a phantom-powered condenser microphone. CAUTION • Make sure that phantom power is turned OFF unless it is needed. • When turning phantom power ON, make sure that no equipment other than phantom-powered devices such as condenser microphones are connected. Devices other than condenser microphones may be damaged if connected to the phantom power supply. Note, however, that the switch may be left on when connecting to balanced dynamic microphones. When connecting an unbalanced device to the analog input jacks (1/4" phone type) and phantom power is turned on, hum or noise may result; this is not a malfunction or failure in the device. • Do not connect or disconnect a device while phantom power is applied. Doing so can damage the connected device and/or the unit itself. • To protect your speaker system, leave the monitor speakers (powered speakers) turned off when switching the phantom power on/off. It’s also a good idea turn all master control and output volume controls down to minimum. Neglect of these precautions may result in large noise bursts that may damage your equipment, your ears, or both. 5 MASTER control Adjusts the signal level sent to the LINE OUT jacks. This allows you to adjust the overall volume without changing the relative volume balance among the channels. This control does not affect the signal sent to the computer. 10 CI2+ Operation Manual 6 PHONES control Adjusts the signal level sent to the PHONES jack, since this output signal is not affected by the MASTER control. 7 MIX control (INPUT—DAW) Adjusts the signal level balance between the signal from the analog input jacks and the signal from an application software, such as DAW. This control does not affect the signal sent to the computer. AI KNOB section The functions of the AI KNOB section differ according to the mode, Normal or Browse. Normal mode is the conventional mode. When a window such as Browse Sounds window in Cubase is opened, the mode changes to the Browse mode automatically. In Browse mode, you can use the button 8 AI KNOB, 9 [LOCK] button, ) [PREVIOUS] button, ! [NEXT] button, and @ [ACTION PAD] button to navigate through Cubase windows, e.g. the Browse Sounds dialog. Below are the explanations of the function in Normal mode. Refer to “The functions of AI KNOB section in the Normal mode and the Browse mode” on page 12 for explanations of the function in the Browse mode. 8 AI KNOB Turning the AI KNOB This multi-function knob can control a desired parameter within the principal window and plugin software in Cubase, specified via the mouse pointer. Pressing the AI KNOB Opens certain windows in Cubase, such as the Browse Sounds window (at which the mode changes to the Browse mode automatically). For details, refer to the following table. The Controls and Connectors Window to be opened Project has not been opened yet Project Assistant Project is opened Browse Sounds window Opening an active VST/VSTi plug-in window Search & Viewer Opening an Interactive Recording panel Preset pop-up list # [REC] button Starts recording on Cubase. English The status of Cubase $ [PLAY/STOP] button Alternately executes Play or Stop on Cubase. Double-clicking this button returns the project cursor on Cubase to the start position. % USB Indicator 9 [LOCK] button/Indicator You can “lock” the parameter to be edited via the AI KNOB by turning this button on. When you locate the mouse pointer to the desired parameter then turn the [LOCK] button on, the AI KNOB will control the “locked” parameter regardless of the mouse pointer’s position. The [LOCK] indicator lights while the parameter is locked. By turning the [LOCK] button off, you can unlock the parameter to be edited and the AI KNOB can then be used to edit another parameter to which the mouse pointer is located. ) [PREVIOUS] button Moves the project cursor on Cubase to the previous marker position. Holding down this button starts fast rewind. Pressing the [PREVIOUS] button and [NEXT] button simultaneously turns on or off the Cycle function on Cubase. ! [NEXT] button Moves the project cursor on Cubase to the next marker position. Holding down this button starts fast forward. Pressing the [PREVIOUS] button and [NEXT] button simultaneously turns on or off the Cycle function on Cubase. This indicator shows the communication state of CI2+ and computer. The indicator lights when the CI2+ is connected to the computer via a USB cable and communication with the computer is enabled. ^ AI READY Indicator This indicator shows the communication state of CI2+ and Cubase. The indicator lights when the Link functions are available. IMPORTANT To use the Link function between the CI2+ and Cubase, you will need to install Cubase/Cubase Essential version 5.1.1 or higher. For details, refer to the following website. http://service.steinberg.de/goto.nsf/show/ supportupdates_ci2plus_gb & BROWSE Indicator This indicator lights when a window in Cubase is opened, such as the Browse Sounds. The indicator lights in the Browse mode. It does not light in the Normal mode. @ [ACTION PAD] button This button is used for an Interactive Recording function on Cubase. When this button is pressed, the Interactive Recording panel is shown. If the display is already shown, pressing the button performs the registered functions in order. Two to six functions can be registered on the Interactive Recording panel. CI2+ Operation Manual 11 The Controls and Connectors The functions of AI KNOB section in the Normal mode and the Browse mode English Normal mode BROWSE off Browse mode BROWSE on Turning the AI KNOB This multi-function knob can control a desired parameter within the principal window and plug-in software in Cubase, specified via the mouse pointer. Moves the cursor. Turning the AI KNOB while holding down the [ACTION PAD] button lets you move the cursor to the next column (only for window having two or more columns). Pressing the AI KNOB Opens certain windows in Cubase, such as the Browse Sounds window (while entering Browse mode in this case). See page 10 for details. Turns the selected item on/off (only for window in which two or more items can be selected) or sets the selected item. Pressing the [LOCK] button You can “lock” the parameter to be edited via the AI KNOB by turning this button on. See page 11 for details. Cancels the selected item and closes the window (returns to Normal mode). Holding down for two seconds or longer cancels all of the selected items (only for window in which two or more items can be selected). Pressing the [ACTION PAD] button (pressing the foot switch) This button is used for an Interactive Record- Moves the cursor to the next column (only for ing function on Cubase. See page 11 for de- window having two or more columns). tails. Pressing the [PREVIOUS] button Moves the project cursor on Cubase to the previous marker position. See page 11 for details. Moves the cursor to the previous column (only for windows having two or more columns). Pressing the [NEXT] button Moves the project cursor on Cubase to the next marker position. See page 11 for details. Moves the cursor to the next column (only for windows having two or more columns). NOTE The [REC] button and [PLAY/STOP] button have the same functions both in the Normal mode and the Browse mode. 12 CI2+ Operation Manual The Controls and Connectors Rear Panel 2 3 1 USB terminal This terminal is used to connect the CI2+ and the computer by using the included USB cable. 2 FOOT SW jack Connect an optional Yamaha FC5 foot switch to this jack. The connected foot switch operates the same as the [ACTION PAD] button. 3 PHONES jack A pair of headphones can be plugged in here. This jack outputs the mixed signal from the analog input jacks and the signal from a DAW or other audio software. The output level can be adjusted using the PHONES control. This output signal is not affected by the MASTER control. 4 5 English 1 5 MIC/LINE/HI-Z jack 1/L (analog input jack 1)/ MIC/LINE jack 2/R (analog input jack 2) Microphones and instruments such as guitars can be connected here using XLR or phone jack cables. The signal received by these jacks is sent to the LINE OUT jacks and computer. NOTE You can directly connect an electric guitar or electric bass without the need for a separate DI box or amp simulator to analog input jack 1. In this case, turn on (O) the [HI-Z] button on the front panel. Make sure to use an unbalanced phone cable when you connect an electric guitar or electric bass. If you use a balanced cable, it will not work correctly. 4 LINE OUT jacks L/R These jacks would typically be connected to monitor speakers (powered speakers). These jacks output the mixed signal from the analog input jacks and the signal from a DAW or other audio software. The output level can be adjusted using the MASTER control. NOTE The volume balance between the analog input signal and the application software like DAW output signal can be adjusted using the MIX control. CI2+ Operation Manual 13 Software Installation Software Installation English To use the CI2+ you must first install the software on the computer. This section explains the software installation. Install Cubase Essential before you install TOOLS for CI2. NOTE • Before installing the software, confirm the “System Requirements for Software” on page 8. The latest information (e.g. OS compatibility, software update, etc.) is available on the following Steinberg website. http://www.steinberg.net/en/support.html • If you have already installed a version of Cubase that is compatible with operation with the CI2+ (page 11), the instructions on installing Cubase Essential described below are not necessary. Jump to the next section “Installing TOOLS for CI2.” Installing Cubase Essential License download (Activation) To install Cubase Essential, there are three steps: Download the software license using the USBeLicenser and ESSENTIAL PRODUCT LICENSE INFORMATION card from the Internet. Follow the instructions below. • Software installation • License download (Activation) • User registration and product registration 6. Connect the USB-eLicenser to a USB NOTE • The “License download” and “User registration and product registration” requires an Internet connection. • Registered customers enjoy various support services such as technical support or upgrade. terminal of your computer. If the “Found New Hardware Wizard” window appears, select “Install the software automatically” to install the driver. 7. Start the “eLicenser Control Center” as Software Installation follows. Install the software using the Cubase Essential DVD-ROM. Follow the instructions below. (Windows) Select [Start] [All Programs] [eLicenser] [eLicenser Control Center]. (Mac OS X) Select [Macintosh HD] [Applications] [eLicenser Control Center]. 1. Start the computer and log on to the Administrator account. 2. Insert the Cubase Essential DVD-ROM into the DVD-ROM drive. 3. When the “WELCOME TO CUBASE ESSENTIAL” window appears, click the corresponding national flag icon to choose your preferred language. 8. Click [Enter Activation Code]. 9. Enter the Activation Code described on the ESSENTIAL PRODUCT LICENSE INFORMATION card. 10. Download the license by following the NOTE If this window does not appear automatically, open the DVD-ROM then double-click the file “Cubase Essential Start Center.” 4. Click “Install CUBASE ESSENTIAL.” 5. Follow the onscreen instructions to install the software. 14 CI2+ Operation Manual on-screen instructions. Software Installation User registration and product registration Windows The installation for Cubase Essential is now complete. English Preparing to install 1 Register your personal information and products on “MySteinberg” in the Steinberg website. See the following website for details. https://www.steinberg.net/en/mysteinberg.html 1. Disconnect all the devices other than the mouse and keyboard from the computer. 2. Start the computer and log on to the Administrator account. Exit any open applications and close all open windows. Installing TOOLS for CI2 TOOLS for CI2 consists of two software components: Yamaha Steinberg USB Driver and Steinberg CI2 Extension. Yamaha Steinberg USB Driver enables communication between the CI2+ and your computer. Using Steinberg CI2 Extension, you can link the CI2+ with a Cubase version which supports the Link functions between both of them (page 11). The TOOLS for CI2 Installer installs these two software components. Follow the instructions below to install the components. Windows: ......................................... page 15 Mac OS X: ....................................... page 17 Preparing to install 2 (Windows XP only) For Windows Vista/Windows 7 users, this setting is not necessary. Go on to step 6. 3. Select [Start] ( [Settings] ) [Control Panel], click “Switch to Classic View” in the upper left of the window. NOTE After completing the installation, make sure to restore the original settings if necessary. 4. Go to [System] [Hardware] [Driver Signing] [Driver Signing Options], and select the radio button to the left of “Ignore – Install the software anyway and don’t ask for my approval” and click [OK]. NOTE After completing the installation, make sure to restore the original settings if necessary. 5. Close the System Properties window by clicking the [OK] button or the Close button ( [X] ) to close the Control Panel. CI2+ Operation Manual 15 Software Installation Software Installation English 6. Insert the TOOLS for CI2 CD-ROM into the CD-ROM drive. 7. Open the CD-ROM, then double-click 13. Select the radio button next to “Install the software automatically” then click [Next]. If a message “The software you are installing has not passed Windows Logo Testing” appears, click [Continue Anyway]. You do not need to abort the installation. the file “setup.exe.” A “Welcome to the InstallShield Wizard for TOOLS for CI2” window appears. (Windows Vista/Windows 7) If the “User Account Control” window appears, click [Continue] or [Yes]. 8. Click [Next] to start the installation. 14. When a message appears indicating that the installation has been completed, click [Finish]. Confirming the installation To cancel the installation, click [Cancel]. 15. Select [Control Panel] from the Start 9. When a message appears indicating that the software has been installed, click [Finish]. menu. 16. Open the Device Manager window as follows. 10. When a window appears requiring you to restart your computer, follow the onscreen instructions to restart the computer. (Windows Vista/Windows 7) Select [Hardware and Sound], then click [Device Manager]. If the “User Account Control” window appears, click [Continue] or [Yes].. 11. Connect the CI2+ directly to the computer (without using a hub) by using the included USB cable. Initial settings of driver (Windows XP only) For Windows Vista/Windows 7 users, the initial settings of the driver are set automatically. Go on to step 15. (Windows XP) Double-click on the System icon to call up the System Properties window, then select the Hardware tab and click [Device Manager]. 17. Click on the [+] mark or [>] mark next to “Sound, video and game controllers,” and confirm that “Steinberg CI2+” is listed. The installation is now complete. 12. The “Found New Hardware Wizard” window appears. Some computers may take a while to display the window. A dialog box may appear asking you whether you wish to connect to Windows Update. In this case, select the radio button to the left of “Not at this time,” then click [Next]. 16 CI2+ Operation Manual Software Installation Mac OS X Confirming the installation (Mac OS X 10.5) English Software Installation For Mac OS X 10.6 users, go on to step 13. 1. Disconnect all the devices other than the mouse and keyboard from the computer. 2. Insert the TOOLS for CI2 CD-ROM into the CD-ROM drive of your computer. 3. Open the CD-ROM, then double-click the file “TOOLS for CI2.mpkg.” 4. A dialog box appears asking if you want to install the software. Click [Continue]. The “Welcome to the TOOLS for CI2 Installer” window appears. 5. Click [Continue]. 11. From the hard disk to which the OS is installed (usually Macintosh HD), click [Applications][Utilities], then doubleclick [Audio MIDI Setup]. The “Audio MIDI Setup” window appears. 12. Click [Audio Devices], then select “Steinberg CI2+” from the pull-down menu in [Properties For]. The current audio settings are shown in the [Audio input] and [Audio Output] fields. NOTE By selecting “Steinberg CI2+” for [Default Output] in System Settings, you can output audio signals of the system sounds and audio player software (e.g., iTunes, etc.) from the CI2+. The “Installation Type” window appears. 6. Click [Install]. The “Authenticate” window appears. 7. Enter the Administrator name and the The installation is now complete. Confirming the installation (Mac OS X 10.6) password, then click [OK]. A message appears prompting you to restart the computer after the installation. 8. Click [Continue Installation] The “Install” window appears indicating the installation progress. When the installation is complete, the “Summary” window appears. 13. From the hard disk to which the OS is installed (usually Macintosh HD), click [Applications][Utilities], then doubleclick [Audio MIDI Setup]. The “Audio Devices” window appears. 14. Select “Steinberg CI2+” from the list of 9. Click [Restart] to restart the computer. audio devices. 10. Connect the CI2+ directly to the com- The current audio settings are shown in the right side of the window. puter (without using a hub) by using the included USB cable. NOTE By selecting “using this device for sound output” in the Action menu at the left bottom of the window, you can output audio signals of audio player software (e.g., iTunes, etc.) from the CI2+. The installation is now complete. CI2+ Operation Manual 17 Connecting to an External Device Connecting to an External Device English Connection Examples Headphones Computer Powered monitor speakers FC5 Electric guitar Microphone Options 18 Foot switch Microphone stand adaptor A Yamaha FC5 foot switch can be connected to the FOOT SW jack. The connected foot switch operates the same as the [ACTION PAD] button. A Yamaha BMS-10A microphone stand adaptor can be attached to the underside of the CI2+. The CI2+ attached with the microphone stand adaptor can then be used with a conventional microphone stand. FC5 BMS-10A CI2+ Operation Manual Try it out English Try it out This section provides information on how to record and edit with Cubase. While going through this section you might find it useful to also refer to the “Controls and Functions” section, as well as the PDF documentation supplied with Cubase Essential (Getting Started and Operation Manual, opened from the “Help” menu). Preparing for using the CI2+ with Cubase You can make the configuration as follows. 1. Make sure that all applications have been quit. 2. Connect the CI2+ and USB-eLicenser to the computer. IMPORTANT • (Windows only) Make sure to use the same USB terminal as the one used in the installation procedure when you connect the CI2+ and USBeLicenser to the computer again. If you connect them to a different USB terminal, you will have to install the driver again. • You need to connect the USB-eLicenser to the computer while running Cubase. 5. Move the cursor to the desired project template by turning the AI KNOB, then press the AI KNOB. A project window will appear. NOTE If you selected the “Prompt for project location” in the Project Assistant window, the “Set Project Folder” window will appear. Select a project folder by using the mouse, then click [OK]. 6. In case the “Missing Ports” window appears. Select the port for each “Mapped Ports” and enter a checkmark for “Map Always,” then click [OK]. 3. Start Cubase on your computer. If the following dialog box is displayed while Cubase is starting, click [Yes]. NOTE If you enter a checkmark for “Map Always,” the “Missing Ports” window will not appear from the next time. 4. When the “Project Assistant” window is displayed, move the cursor to “Recording” by turning the AI KNOB, then press the [ACTION PAD] button. Preparation for using the CI2+ with Cubase is now complete. NOTE Pressing the [ACTION PAD] button moves the focus which can be operated by the AI KNOB to the next column or pane. CI2+ Operation Manual 19 Try it out Recording English You can record your performance to Cubase with the Interactive Recording function by following the instructions below. To operate the Interactive Recording function, use the [ACTION PAD] button. 4. Play the instrument, and adjust the recording level with the CI2+ GAIN controls. To achieve the best balance of the recording level between S/N ratio and dynamic range, adjust the level so that the PEAK Indicator lights only occasionally and briefly on the highest input transients. NOTE NOTE • Interactive Recording function works optimally when “Tapemachine Style” is selected in the “Auto Monitoring” setting in Cubase. Open the Cubase menu [File (Windows) or Cubase Essential (Mac)] [Preference] [VST], then set the “Tapemachine Style” to “Auto Monitoring.” • The connected optional Yamaha FC5 foot switch operates the same as the [ACTION PAD] button. • If the Clipping Indicator in the Transport panel on Cubase lights, lower the CI2+ GAIN controls. 1. Connect external devices such as micro- • The MIX control let you adjust the signal level balance between the signal from the analog input jacks and the signal from Cubase. 5. Press the [ACTION PAD] button to open the Interactive Recording panel. phones and instruments to analog input jacks. CAUTION Before connecting external devices such as microphones and instruments, set the volume of external devices and monitor speakers (powered speakers) to the minimum. We also recommend that you set the MASTER control to the minimum and turn off (N) both the [HI-Z INPUT 1] button and [PHANTOM INPUT 1&2] button, to avoid risk of loud noises that could cause hearing loss or device damage. 6. Press the [ACTION PAD] button to start 2. Click in the track list (the area in which the track names are displayed) to select a track to record on. recording. Recording will begin since “Record” has been executed on the Interactive Recording panel. 7. Play the instrument. NOTE • You can abort the Interactive Recording function and close the Interactive Recording panel by pressing the [LOCK] button. • You can return to step 6 to abort and retry the recording by holding down the [LOCK] button for two seconds or longer. 3. Make sure the [Record Enable] button for the track to be recorded is turned on. If the [Record Enable] button is off, click it to turn it on. 20 CI2+ Operation Manual Try it out press the [ACTION PAD] button to stop recording. Recording will stop since “Stop” has been executed on the Interactive Recording panel. 9. Press the [ACTION PAD] button to return the project cursor to the start position. The project cursor will return to start position since “Return to Start Position” has been executed on the Interactive Recording panel. To hear playback of the track you have just recorded, click the Transport panel [Play] button. Recording operation is now complete. TIP You can also operate in the Interactive Recording panel as shown below. 1 2 3 4 TIP Setting the audio driver buffer size English 8. When you finish recording the track, Noise produced when using audio applications such as DAW software may affect audio recording and/or playback. In most cases, you can solve these problems by adjusting the audio driver buffer size (the size of memory used to temporarily hold data to avoid intermittent playback). The buffer size can usually be adjusted via the audio driver setup window in the application. (When using ASIO compatible software for Windows, the buffer size can be adjusted in the ASIO Buffer Size parameter via the Control Panel of the Yamaha Steinberg USB Driver.) While the higher buffer size reduces load to the computer CPU but produces latency (time lag) during recording/playback, the smaller buffer size may result in noise or the sound cutting off. Make sure to set the buffer size to an appropriate value depending on the performance of your computer, the number of audio/MIDI tracks being recorded/played back on the DAW software, the number of plug-in software, and so on. 1 Saves and loads the sequence of actions. 2 Increases and decreases the number of actions. The available number of actions is two through six. 3 Changes the action to another action. 4 Switches the panel to the small Interactive Recording panel. In the small panel, you can only load the sequence of actions. CI2+ Operation Manual 21 Try it out Editing [LOCK] button English You can edit parameters in the project with the AI KNOB and [LOCK] button by following the instructions. The [LOCK] button can “lock” the parameter to be edited via the AI KNOB. You can lock the volume parameter to the AI KNOB as follows. 1. Locate the mouse pointer to the volume AI KNOB This multi-function knob can control a desired parameter within the principal window and plugin software on Cubase, specified via the mouse pointer. In the following examples, we’ll control the volume and panning parameter of the audio track on the mixer window. parameter then turn on the [LOCK] button. [LOCK] indicator will light. 2. Move the mouse pointer to the other location. 3. Turn the AI KNOB 1. Click [Mixer] from the [Devices] menu. Mixer window will appear. 2. Locate the mouse pointer to the volume or panning parameter of the audio track on the mixer window. panning The AI KNOB will control the volume parameter regardless of the mouse pointer’s position. By turning the [LOCK] button off, you can unlock the parameter to be edited and the AI KNOB can then be used to edit another parameter to which the mouse pointer is located. Continue to edit other parameters in the same way. Editing operation is now complete. volume For more information on this product, please visit the following Steinberg website: http://www.steinberg.net/ 3. Turn the AI KNOB The AI KNOB will control the parameter on which the mouse pointer is located. NOTE The assignable parameters to the AI KNOB are parameters that can be automated within the principal window and plug-in software on Cubase. Plugin software compatible with the AI KNOB are the VST 3 plug-ins included with Cubase (as of February 2010). For the latest information about compatible plug-in software, refer to the following URL: http://service.steinberg.de/goto.nsf/show/ supportupdates_ci2plus_gb 22 CI2+ Operation Manual Troubleshooting The power of the device does not turn on. • Make sure that the CI2+ is properly connected to the computer via a USB cable. The USB bus-power is necessary to use the CI2+. • Confirm whether or not a proper USB cable is used. If the USB cable is broken or damaged, have the USB cable replaced with a known working one. Use a USB cable no longer than 1.5 meters. • Connect the CI2+ to a computer without a USB hub. English Troubleshooting Noise occurs, or the sound is intermittent or distorted. • Is the PEAK indicator flashing red? You might have to lower GAIN control level to avoid distortion. • Does your computer satisfy the system requirements? Refer to “System Requirements” on page 8. • Is the buffer size setting of the Yamaha Steinberg USB Driver set properly? Refer to the “Setting the audio driver buffer size” on page 21. No sound. • Make sure that the MASTER/PHONES/ MIX controls are set properly. • Are your speaker cables connected properly? Refer to “Connection Examples” on page 18. • Are your speaker cables shorted? • Are the volume controls of your sources, audio devices, applications software, computer operating system, etc., set at appropriate levels? • (Windows only) Is the output of your computer operating system muted? • Do you have several applications running at the same time? Be sure to quit all applications you are not using. • Is the “ASIO Driver” setting on Cubase set properly? • Are any other applications, device drivers, or USB devices (scanners, printers, etc.) running at the same time? Be sure to quit all applications you are not using. • Are you playing back a large number of audio tracks? The number of tracks you can play at the same time will depend on the performance of the computer you are using. You may experience intermittent playback if you exceed your computer's capabilities. • Are you recording or playing long continuous sections of audio? The audio data processing capabilities of your computer will depend on a number of factors including CPU speed and access to external devices. • Is the network adaptor running? Disable the suspected network adaptor. Some network adaptors can cause noise. Make sure that the “Yamaha Steinberg USB ASIO (Windows)” or “Steinberg CI2+ (Mac)” is selected on the “ASIO Driver” in the “VST Audio System” window (called up via [Device Setup…] under the [Devices] menu). CI2+ Operation Manual 23 Troubleshooting Cubase does not recognize the CI2+. English • Make sure that the CI2+ is properly connected to the computer via a USB cable. • Confirm whether or not a proper USB cable is used. If the USB cable is broken or damaged, have the USB cable replaced with a known working one. Use a USB cable no longer than 1.5 meters. • Confirm whether or not the CI2+ is connected to the computer before starting Cubase. • Confirm whether or not the “Yamaha Steinberg USB Driver” and “Steinberg CI2 Extension” have been installed. If not, install them. • Confirm whether or not a version of Cubase that is compatible with operation with the CI2+ (page 11) has already been installed. • Make sure that CI2+ is selected as the port setting on Cubase. The port is described in the Device Setup window (called up via [Device Setup...] under the [Devices] menu) when selecting “Steinberg CI2+” under “Remote Devices” in the Devices box. • Make sure that there is no check mark in “In ‘All MIDI Inputs’” for CI2+ MIDI port on the “MIDI Port Setup” window (called up via [Device Setup…] under the [Devices] menu.) • Are you connecting the Steinberg CC121 and the CI2+ simultaneously with one computer? If you are connecting the Steinberg CC121 and the CI2+ simultaneously with one computer, the AI KNOB and [LOCK] button on the CI2+ cannot be used. 24 CI2+ Operation Manual Computer does not recognize the USB-eLicenser properly. • Connect the USB-eLicenser to a computer without a USB hub. • Make sure that the latest version of the software for the USB-eLicenser has been installed. If it is not the case, download it from the following website and install it. http://www.elicenser.net/en Uninstalling the TOOLS for CI2 English Uninstalling the TOOLS for CI2 To uninstall TOOLS for CI2, you must remove the following two software components. • Yamaha Steinberg USB Driver • Steinberg CI2 Extension Windows Mac OS X 1. Disconnect all other USB devices except Removing Yamaha Steinberg USB Driver mouse and keyboard from the computer. 2. Log on to the Administrator account. Exit any open applications and close all open windows. 3. Open the window for the uninstall operation as follows. Remove the following folders and files from the boot disk (usually Macintosh HD). /System/Library/Extensions YamahaSteinbergUSBAudio.kext /Application/Yamaha/USBDriver/ Yamaha Steinberg USB Control Panel.app /Library/PreferencePanes/ Yamaha Steinberg USB.prefPane (Windows Vista/Windows 7) From the Start menu, select [Control Panel] [Uninstall a Program] to call up the “Uninstall or change a program” panel. /Library/Preferences/ com.yamaha.YamahaSteinbergUSBDriver.plist (Windows XP) From the Start menu, select ([Settings] ) [Control Panel] [Add or Remove Programs] to display the Add or Remove Programs panel. Click “Change or Remove Programs” located in the upper left. /Library/Audio/MIDI Devices/Yamaha/Images/ USB_1500.tiff USB_1502.tiff 4. Select “Yamaha Steinberg USB Driver,” ”Steinberg CI2 Extension” from the list. /Library/Audio/MIDI Drivers/ YamahaSteinbergUSBMIDI.plugin /Library/Receipts/ YamahaSteinbergUSBAudioDriver.pkg YamahaSteinbergUSBControlPanel.pkg YamahaSteinbergUSBDriverplist.pkg YamahaSteinbergUSBMIDIPlugIn.pkg YamahaSteinbergUSBMIDIIcon.pkg YamahaSteinbergUSBPrefPane.pkg 5. Uninstall them as follows. (Windows Vista/Windows 7) Click the [Uninstall]/[Uninstall/Change]. If the “User Account Control” window appears, click [Continue] or [Yes]. Follow the on-screen instructions to remove the software. (Windows XP) Click [Change/Remove]/[Remove]. Follow the on-screen instructions to remove the software. Removing Steinberg CI2 Extension Remove the following folders and files from the boot disk (usually Macintosh HD). /Library/Application Support/Steinberg/Components/ ci2_extension_u.bundle /Library/Application Support/Yamaha/ InteractiveRecording /Library/Receipts/ Steinberg CI2 Extension.pkg CI2+ Operation Manual 25 Appendix Appendix English Input and Output Specifications Input Level Analog Input Type MIC 1/L, 2/R XLR type, balanced +48V Phantom powered HI-Z 1/L Phone type, unbalanced LINE 1/L, 2/R TRS phone type, balanced Nominal Level Maximum Level Input Impedance -60dBu — -16dBu -6dBu 3kΩ -44dBu — 0dBu +10dBu 500kΩ -34dBu — +10dBu +20dBu 62kΩ Output Level Analog Output Type Nominal Level Maximum Level Input Impedance LINE OUT L, R TRS phone type, impedance balanced +4dBu +10dBu 10kΩ PHONES TRS phone type, stereo 3.6mW 6.0mW 40Ω General Specifications USB terminal USB1.1, 44.1/48 kHz, 24 bit, bus-powered Dimensions (W x H x D) W190 x H45.4 x D134.5 mm Net Weight 701 g Included Accessories • • • • • • • Operation Manual TOOLS for CI2 CD-ROM Cubase Essential DVD-ROM USB-eLicenser ESSENTIAL PRODUCT LICENSE INFORMATION card USB cable Ferrite core Specifications and descriptions in this manual are for information purposes only. Steinberg/Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Steinberg/Yamaha dealer. 26 CI2+ Operation Manual English License Agreement for TOOLS for CI2 ATTENTION SOFTWARE LICENSE AGREEMENT PLEASE READ THIS SOFTWARE LICENSE AGREEMENT (“AGREEMENT”) CAREFULLY BEFORE USING THIS SOFTWARE. YOU ARE ONLY PERMITTED TO USE THIS SOFTWARE PURSUANT TO THE TERMS AND CONDITIONS OF THIS AGREEMENT. THIS AGREEMENT IS BETWEEN YOU (AS AN INDIVIDUAL OR LEGAL ENTITY) AND YAMAHA CORPORATION (“YAMAHA”). BY BREAKING THE SEAL OF THIS PACKAGE YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. IF YOU DO NOT AGREE WITH THE TERMS, DO NOT INSTALL, COPY, OR OTHERWISE USE THIS SOFTWARE. 1. GRANT OF LICENSE AND COPYRIGHT Yamaha hereby grants you the right to use one copy of the software program(s) and data (“SOFTWARE”) accompanying this Agreement. The term SOFTWARE shall encompass any updates to the accompanying software and data. The SOFTWARE is owned by Yamaha and/or Yamaha’s licensor(s), and is protected by relevant copyright laws and all applicable treaty provisions. While you are entitled to claim ownership of the data created with the use of SOFTWARE, the SOFTWARE will continue to be protected under relevant copyrights. • You may use the SOFTWARE on a single computer. • You may make one copy of the SOFTWARE in machine-readable form for backup purposes only, if the SOFTWARE is on media where such backup copy is permitted. On the backup copy, you must reproduce Yamaha’s copyright notice and any other proprietary legends that were on the original copy of the SOFTWARE. • You may permanently transfer to a third party all your rights in the SOFTWARE, provided that you do not retain any copies and the recipient reads and agrees to the terms of this Agreement. 2. RESTRICTIONS • You may not engage in reverse engineering, disassembly, decompilation or otherwise deriving a source code form of the SOFTWARE by any method whatsoever. • You may not reproduce, modify, change, rent, lease, or distribute the SOFTWARE in whole or in part, or create derivative works of the SOFTWARE. • You may not electronically transmit the SOFTWARE from one computer to another or share the SOFTWARE in a network with other computers. • You may not use the SOFTWARE to distribute illegal data or data that violates public policy. • You may not initiate services based on the use of the SOFTWARE without permission by Yamaha Corporation. Copyrighted data, including but not limited to MIDI data for songs, obtained by means of the SOFTWARE, are subject to the following restrictions which you must observe. • Data received by means of the SOFTWARE may not be used for any commercial purposes without permission of the copyright owner. • Data received by means of the SOFTWARE may not be duplicated, transferred, or distributed, or played back or performed for listeners in public without permission of the copyright owner. • The encryption of data received by means of the SOFTWARE may not be removed nor may the electronic watermark be modified without permission of the copyright owner. 3. TERMINATION This Agreement becomes effective on the day that you receive the SOFTWARE and remains effective until terminated. If any copyright law or provisions of this Agreement is violated, the Agreement shall terminate automatically and immediately without notice from Yamaha. Upon such termination, you must immediately destroy the licensed SOFTWARE, any accompanying written documents and all copies thereof. 4. LIMITED WARRANTY ON MEDIA As to SOFTWARE sold on tangible media, Yamaha warrants that the tangible media on which the SOFTWARE is recorded will be free from defects in materials and workmanship under normal use for a period of fourteen (14) days from the date of receipt, as evidenced by a copy of the receipt. Yamaha’s entire liability and your exclusive remedy will be replacement of the defective media if it is returned to Yamaha or an authorized Yamaha dealer within fourteen days with a copy of the receipt. Yamaha is not responsible for replacing media damaged by accident, abuse or misapplication. TO THE FULLEST EXTENT PERMITTED BY LAW, YAMAHA EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES ON THE TANGIBLE MEDIA, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. CI2+ Operation Manual 27 5. DISCLAIMER OF WARRANTY ON SOFTWARE English You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk. The SOFTWARE and related documentation are provided “AS IS” and without warranty of any kind. NOTWITHSTANDING ANY OTHER PROVISION OF THIS AGREEMENT, YAMAHA EXPRESSLY DISCLAIMS ALL WARRANTIES AS TO THE SOFTWARE, EXPRESS, AND IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY RIGHTS. SPECIFICALLY, BUT WITHOUT LIMITING THE FOREGOING, YAMAHA DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS, THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERRORFREE, OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED. 6. LIMITATION OF LIABILITY YAMAHA’S ENTIRE OBLIGATION HEREUNDER SHALL BE TO PERMIT USE OF THE SOFTWARE UNDER THE TERMS HEREOF. IN NO EVENT SHALL YAMAHA BE LIABLE TO YOU OR ANY OTHER PERSON FOR ANY DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS, LOST DATA OR OTHER DAMAGES ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THE SOFTWARE, EVEN IF YAMAHA OR AN AUTHORIZED DEALER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. In no event shall Yamaha’s total liability to you for all damages, losses and causes of action (whether in contract, tort or otherwise) exceed the amount paid for the SOFTWARE. 7. THIRD PARTY SOFTWARE Third party software and data (“THIRD PARTY SOFTWARE”) may be attached to the SOFTWARE. If, in the written materials or the electronic data accompanying the Software, Yamaha identifies any software and data as THIRD PARTY SOFTWARE, you acknowledge and agree that you must abide by the provisions of any Agreement provided with the THIRD PARTY SOFTWARE and that the party providing the THIRD PARTY SOFTWARE is responsible for any warranty or liability related to or arising from the THIRD PARTY SOFTWARE. Yamaha is not responsible in any way for the THIRD PARTY SOFTWARE or your use thereof. 28 CI2+ Operation Manual • Yamaha provides no express warranties as to the THIRD PARTY SOFTWARE. IN ADDITION, YAMAHA EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, as to the THIRD PARTY SOFTWARE. • Yamaha shall not provide you with any service or maintenance as to the THIRD PARTY SOFTWARE. • Yamaha is not liable to you or any other person for any damages, including, without limitation, any direct, indirect, incidental or consequential damages, expenses, lost profits, lost data or other damages arising out of the use, misuse or inability to use the THIRD PARTY SOFTWARE. 8. GENERAL This Agreement shall be interpreted according to and governed by Japanese law without reference to principles of conflict of laws. Any dispute or procedure shall be heard before the Tokyo District Court in Japan. If for any reason a court of competent jurisdiction finds any portion of this Agreement to be unenforceable, the remainder of this Agreement shall continue in full force and effect. 9. COMPLETE AGREEMENT This Agreement constitutes the entire agreement between the parties with respect to use of the SOFTWARE and any accompanying written materials and supersedes all prior or contemporaneous understandings or agreements, written or oral, regarding the subject matter of this Agreement. No amendment or revision of this Agreement will be binding unless in writing and signed by a fully authorized representative of Yamaha. This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC. By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. English Information for Users on Collection and Disposal of Old Equipment [For business users in the European Union] If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] Verbraucherinformation zur Sammlung und Entsorgung alter Elektrogeräte Befindet sich dieses Symbol auf den Produkten, der Verpackung und/oder beiliegenden Unterlagen, so sollten benutzte elektrische Geräte nicht mit dem normalen Haushaltsabfall entsorgt werden. In Übereinstimmung mit Ihren nationalen Bestimmungen und den Richtlinien 2002/96/EC, bringen Sie alte Geräte bitte zur fachgerechten Entsorgung, Wiederaufbereitung und Wiederverwendung zu den entsprechenden Sammelstellen. Durch die fachgerechte Entsorgung der Elektrogeräte helfen Sie, wertvolle Ressourcen zu schützen und verhindern mögliche negative Auswirkungen auf die menschliche Gesundheit und die Umwelt, die andernfalls durch unsachgerechte Müllentsorgung auftreten könnten. Für weitere Informationen zum Sammeln und Wiederaufbereiten alter Elektrogeräte, kontaktieren Sie bitte Ihre örtliche Stadt- oder Gemeindeverwaltung, Ihren Abfallentsorgungsdienst oder die Verkaufsstelle der Artikel. Deutsch This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. [Information für geschäftliche Anwender in der Europäischen Union] Dieses Symbol gilt nur innerhalb der Europäischen Union. Wenn Sie solche Artikel ausrangieren möchten, kontaktieren Sie bitte Ihre örtlichen Behörden oder Ihren Händler und fragen Sie nach der sachgerechten Entsorgungsmethode. Information concernant la Collecte et le Traitement des déchets d’équipements électriques et électroniques. Le symbole sur les produits, l'emballage et/ou les documents joints signifie que les produits électriques ou électroniques usagés ne doivent pas être mélangés avec les déchets domestiques habituels. Pour un traitement, une récupération et un recyclage appropriés des déchets d’équipements électriques et électroniques, veuillez les déposer aux points de collecte prévus à cet effet, conformément à la réglementation nationale et aux Directives 2002/96/EC. En vous débarrassant correctement des déchets d’équipements électriques et électroniques, vous contribuerez à la sauvegarde de précieuses ressources et à la prévention de potentiels effets négatifs sur la santé humaine qui pourraient advenir lors d'un traitement inapproprié des déchets. Pour plus d'informations à propos de la collecte et du recyclage des déchets d’équipements électriques et électroniques, veuillez contacter votre municipalité, votre service de traitement des déchets ou le point de vente où vous avez acheté les produits. [Pour les professionnels dans l'Union Européenne] Español [Entsorgungsinformation für Länder außerhalb der Europäischen Union] Français Wenn Sie Elektrogeräte ausrangieren möchten, kontaktieren Sie bitte Ihren Händler oder Zulieferer für weitere Informationen. Si vous souhaitez vous débarrasser des déchets d’équipements électriques et électroniques veuillez contacter votre vendeur ou fournisseur pour plus d'informations. [Information sur le traitement dans d'autres pays en dehors de l'Union Européenne] Información para Usuarios sobre Recolección y Disposición de Equipamiento Viejo Este símbolo en los productos, embalaje, y/o documentación que se acompañe significa que los productos electrónicos y eléctricos usados no deben ser mezclados con desechos hogareños corrientes. Para el tratamiento, recuperación y reciclado apropiado de los productos viejos, por favor llévelos a puntos de recolección aplicables, de acuerdo a su legislación nacional y las directivas 2002/96/EC. Al disponer de estos productos correctamente, ayudará a ahorrar recursos valiosos y a prevenir cualquier potencial efecto negativo sobre la salud humana y el medio ambiente, el cual podría surgir de un inapropiado manejo de los desechos. Para mayor información sobre recolección y reciclado de productos viejos, por favor contacte a su municipio local, su servicio de gestión de residuos o el punto de venta en el cual usted adquirió los artículos. [Para usuarios de negocios en la Unión Europea] Si usted desea deshacerse de equipamiento eléctrico y electrónico, por favor contacte a su vendedor o proveedor para mayor información. [Información sobre la Disposición en otros países fuera de la Unión Europea] Este símbolo sólo es válidos en la Unión Europea. Si desea deshacerse de estos artículos, por favor contacte a sus autoridades locales y pregunte por el método correcto de disposición. Italiano Ce symbole est seulement valables dans l'Union Européenne. Si vous souhaitez vous débarrasser de déchets d’équipements électriques et électroniques, veuillez contacter les autorités locales ou votre fournisseur et demander la méthode de traitement appropriée. Informazioni per gli utenti sulla raccolta e lo smaltimento di vecchia attrezzatura English Questo simbolo sui prodotti, sull’imballaggio, e/o sui documenti che li accompagnano significa che i prodotti elettriche e elettroniche non dovrebbero essere mischiati con i rifiuti domestici generici. Per il trattamento, recupero e riciclaggio appropriati di vecchi prodotti, li porti, prego, ai punti di raccolta appropriati, in accordo con la Sua legislazione nazionale e le direttive 2002/96/CE. Smaltendo correttamente questi prodotti, Lei aiuterà a salvare risorse preziose e a prevenire alcuni potenziali effetti negativi sulla salute umana e l’ambiente, che altrimenti potrebbero sorgere dal trattamento improprio dei rifiuti. Per ulteriori informazioni sulla raccolta e il riciclaggio di vecchi prodotti, prego contatti la Sua amministrazione comunale locale, il Suo servizio di smaltimento dei rifiuti o il punto vendita dove Lei ha acquistato gli articoli. [Per utenti imprenditori dell’Unione europea] Se Lei desidera disfarsi di attrezzatura elettrica ed elettronica, prego contatti il Suo rivenditore o fornitore per ulteriori informazioni. [Informazioni sullo smaltimento negli altri Paesi al di fuori dell’Unione europea] Questo simbolo è validi solamente nell’Unione europea. Se Lei desidera disfarsi di questi articoli, prego contatti le Sue autorità locali o il rivenditore e richieda la corretta modalità di smaltimento. Deutsch (weee_eu) ► Warranty Terms and Conditions available as printed PDF file at www.steinberg.net/warranty Français The Warranty Terms and Conditions available as printed PDF file at www.steinberg.net/warranty apply only for countries of the European Economic Area (EEA) and Switzerland. ► Gewährleistungsbestimmungen finden Sie als druckbare PDF Datei unter www.steinberg.de/warranty Die Gewährleistungsbestimmungen in Schriftform sind als PDF-Datei unter www.steinberg.de/warranty erhältlich und gelten nur für den Europäischen Wirtschaftsraum (EWR) und die Schweiz. Español ► Les conditions de garantie se trouvent dans le document PDF imprimable sous www.steinberg.net/warranty Les conditions de garantie disponibles au format PDF à la page www.steinberg.net/warranty s’appliquent uniquement aux pays de l’Espace économique européen (EEE) et à la Suisse. Italiano ► Las condiciones de garantía se encuentran en el documento PDF en www.steinberg.net/warranty Los términos y condiciones de la garantía como archivo PDF para su impresión en www.steinberg.net/ warranty sólo están disponible en países del Espacio Económico Europeo (EEE) y Suiza. ► Termini e Condizioni di Garanzia disponibili su file PDF stampabile all’indirizzo web www.steinberg.net/warranty I termini e le condizioni della garanzia, disponibili in formato PDF all’indirizzo www.steinberg.net/warranty, sono validi soltanto per I paesi dell’Area Economica Europea (EEA) e per la Svizzera. For details of products, please contact your nearest Steinberg representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Steinberg ou au distributeur le plus proche de vous figurant dans la liste suivante. Gedung Yamaha Music Center, Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: 21-520-2577 CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 JAPAN Yamaha Corporation, Steinberg Information Center U.S.A. Steinberg North America, c/o Yamaha Corporation of America Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-5270 KOREA Yamaha Music Korea Ltd. 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011 8F, 9F, Dongsung Bldg. 158-9 Samsung-Dong, Kangnam-Gu, Seoul, Korea Tel: 080-004-0022 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México S.A. de C.V. MALAYSIA Yamaha Music Malaysia, Sdn., Bhd. Calz. Javier Rojo Gómez #1149, Col. Guadalupe del Moral C.P. 09300, México, D.F., México Tel: 55-5804-0600 Lot 8, Jalan Perbandaran, 47301 Kelana Jaya, Petaling Jaya, Selangor, Malaysia Tel: 3-78030900 BRAZIL Yamaha Musical do Brasil Ltda. Rua Joaquim Floriano, 913 - 4' andar, Itaim Bibi, CEP 04534-013 Sao Paulo, SP. BRAZIL Tel: 011-3704-1377 ARGENTINA Yamaha Music Latin America, S.A. Sucursal de Argentina Viamonte 1145 Piso2-B 1053, Buenos Aires, Argentina Tel: 1-4371-7021 SINGAPORE Yamaha Music Asia Pte., Ltd. #03-11 A-Z Building 140 Paya Lebor Road, Singapore 409015 Tel: 747-4374 TAIWAN Yamaha KHS Music Co., Ltd. 3F, #6, Sec.2, Nan Jing E. Rd. Taipei. Taiwan 104, R.O.C. Tel: 02-2511-8688 THAILAND Siam Music Yamaha Co., Ltd. PANAMA AND OTHER LATIN AMERICAN COUNTRIES/ CARIBBEAN COUNTRIES Yamaha Music Latin America, S.A. 4, 6, 15 and 16th floor, Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, Thailand Tel: 02-215-2626 Torre Banco General, Piso 7, Urbanización Marbella, Calle 47 y, Aquilino de la Guardia, Ciudad de Panamá, Panamá Tel: +507-269-5311 OTHER ASIAN COUNTRIES Yamaha Corporation, Asia-Pacific Music Marketing Group EUROPE Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2317 Steinberg Media Technologies GmbH Neuer Hoeltigbaum 22-32, 22143 Hamburg, Germany Tel: +49-(0)40-210 35 0 OCEANIA AFRICA AUSTRALIA Yamaha Music Australia Pty. Ltd. Yamaha Corporation, Asia-Pacific Music Marketing Group Level 1, 99 Queensbridge Street, Southbank, Victoria 3006, Australia Tel: 3-9693-5111 Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312 NEW ZEALAND Music Works LTD MIDDLE EAST P.O.BOX 6246 Wellesley, Auckland 4680, New Zealand Tel: 9-634-0099 Yamaha Music Gulf FZE LOB 16-513, P.O.Box 17328, Jubel Ali, Dubai, United Arab Emirates Tel: +971-4-881-5868 ASIA Para detalles sobre productos, contacte su tienda Steinberg más cercana o el distribuidor autorizado que se lista debajo. INDONESIA PT. Yamaha Music Indonesia (Distributor) PT. Nusantik NORTH AMERICA THE PEOPLE’S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co.,Ltd. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Steinberg Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. COUNTRIES AND TRUST TERRITORIES IN PACIFIC OCEAN Yamaha Corporation, Asia-Pacific Music Marketing Group Nakazawa-cho 10-1, Naka-ku, Hamamatsu, Japan 430-8650 Tel: +81-53-460-2312 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 HEAD OFFICE Steinberg Media Technologies GmbH Neuer Hoeltigbaum 22-32, 22143 Hamburg, Germany Tel: +49-(0)40-210 35 0 ST01 Steinberg Web Site http://www.steinberg.net U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2010 Yamaha Corporation WU10640 002MWAP?.?-01A0
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Fill forms, Extract, Assemble, Print high-res Page Mode : UseOutlines XMP Toolkit : 3.1-702 Modify Date : 2010:03:03 13:39:14+09:00 Create Date : 2010:02:23 14:25:49+09:00 Metadata Date : 2010:03:03 13:39:14+09:00 Format : application/pdf Title : CI2+ Operation Manual Creator : U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation Description : ci2plus_en_om_a0 Document ID : uuid:395ebd4d-6640-4482-9e4f-07601852b47a Instance ID : uuid:d201962c-c66e-43f9-a293-0b10719b77b1 Has XFA : No Page Count : 32 Subject : ci2plus_en_om_a0 Author : U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha CorporationEXIF Metadata provided by EXIF.tools