P24957 E26_installation E26 Installation
User Manual: e26_installation Eaton Cutler-Hammer Stacklight ation - AutomationDirect
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
INSTALLATION INSTRUCTIONS P24957 Effective November 2010 Supersedes August 1999 E26 Stacklight The E26 Stacklight provides a visual and/or audible status indication. Plug-in light modules consist of a lens with a diffuser for steady of flashing incandescent lamps or LEDs. Up to six color modules provide signals with 360 degree visibility. Flashing xenon tube lights and audible alarms are available. WARNING Mounting and NEMA - IEC Enclosure Type Ratings Base Mounting - For use on a flat surface of Type 1, 4, 4X, and 13 enclosures (IP65). Threaded 3/4” Conduit Mounting - Use with a Myers ST-2 or ST-2CP hub, or suitable enclosure with threaded 3/4” NPT conduit entrance for Type 1, 4, 4X, and 13 enclosure ratings (IP65). Alarm Unit - Enclosure Type 1 (IP20). REMOVE POWER BEFORE DISASSEMBLING THE STACKLIGHT OR CHANGING LAMPS. THESE INSTRUCTIONS MUST BE READ AND CLEARLY UNDERSTOOD BEFORE INSTALLING OR OPERATING THIS EQUIPMENT. THIS EQUIPMENT IS TO BE INSTALLED AND SERVICED BY A TRAINED ELECTRICIAN. Mount the stacklight in the vertical position on a flat horizontal surface. Specifications Lamp Type BA15d. 6 watts maximum (See page 5 for C-H lamp replacement catalog numbers) Operating Temperature Range -20oC to 60oC (-4oF to 140oF) Operating Humidity 95% @ 40oC (104oF) Storage Temperature -40oC to 80oC (-40oF to 176oF) IEC Ratings Compliance IEC60947-5-1, EN60947-5-1 Degree of Protection against Electrical Contact for Stacklight IP2X Degree of Protection against Electrical Contact for Alarm Unit IP0X Rated Insulation Voltage (Ui) 690V Rated Operational Votlage (Ie) 250 max Rated impulse withstand voltage (Uimp) 1.5Kv Shock Resistance (IEC 68-2-27) Without vibration damper fitted 11ms, 15g With vibration damper fitted 18ms, 30g Vibration (IEC 68-2-6) Without vibration damper fitted 10 sweeps, 10-50Hxz, 2g With vibration damper fitted 10 sweeps, 10-150Hz, 10g Bump (IEC 68-2-29) Without vibration damper fitted 6ms duration, 1000 bumps, 15g With vibration damper fitted 6ms duration, 1000 bumps, 25g Fig. 1 Typical Stacklight Assembly (Exploded View) INSTALLATION INSTRUCTIONS P24957 E26 Stacklight Effective November 2010 Field Wiring Remove the Terminal Board for Wiring Squeeze the locking clips one side at a time and pull up on the terminal board to disengage the locking tabs from the cutouts in the stacklight base. Repeat this procedure for the other locking clip. Lift the terminal board out of the stacklight base. Connect Field Wiring to Terminal Blocks Connect field wiring per diagrams below. Terminals accept wire sizes 14AWG - 30AWG (2.5 sq mm - 0.05 sq mm) for single conductors and 18AWG to 26AWG (0.75 sq mm - 0.14 sq mm) for two conductors. Do not mix solid and stranded wire in the same terminal. Recommended tightening torque is 4.4 lb/in to 5.3 lb/ in (0.5Nm to 0.6 Nm). After wiring is complete, proceed to “Assembly” on Page 3. Fig. 2 Use with incandescent lamps, convvtinuous LEDs, flashing LEDs, alarm units, and xenon flashing units. Fig. 3 Standard Boase (Continuous Lights) ??? Use with incandescent lamps only, up to maximum number per table Fig. 4 Flashing Base Continuous lights may be combined with flashing lights according to the wiring diagrams above. 2 EATON CORPORATION www.eaton.com E26 Stacklight INSTALLATION INSTRUCTIONS P24957 Effective November 2010 Assembly MAXIMUM COMBINATIONS OF STACKLIGHT MODULES After wiring is complete, assemble light diffusers. While observing the orientation of the two guides, plug the light diffuser into the terminal connections in the stacklight base or previous diffuser. See Fig. 4. Incandescent or LED Modules Xenon Modules Alarm Modules* Maximum Numbr of Modules 6 -- -- 6 5 -- 1 6 4 1 -- 5 3 1 1 5 2 2 -- 4 1 2 1 4 Assemble lenses and cover by turning clockwise to engage the bayonets in the stacklight base or previous lens. See Fig. 5. * Alarm must be the Top Module. Guide Fig. 5 Fig. 4 WARNING TURN OFF POWER BEFORE INSTALLING ALARM Drill 2 holes in stacklight base to 0.165” (4.2mm). Mount stacklight with #8-32 (M4) screws. Tighten to torque of 7 lb/in (0.79 Nm). Fig. 7 Mounting Dimensions for Stacklight Base If an audible alarm is to be installed, connect the two leads from the alarm to the terminal connections at the innermost points on the connectors as shown in Fig. 6. Without Vibration Damper: Mount stacklight with #8-32 (M4) screws. Tighten to torque of 7 lb/in (0.79 Nm). With Vibration Damper: Discard sealing washer. Mount stacklight with #8-32 (M4 screws). Tighten to torque of 6 lb/in (0.68 Nm). Fig. 6 Installing Alarm Unit Fig. 7 Mounting Dimensions for Mounting Base EATON CORPORATION www.eaton.com 3 INSTALLATION INSTRUCTIONS P24957 E26 Stacklight Effective November 2010 Disasssembly and Lamp Replacement WARNING TURN OFF POWER BEFORE DISASSEMBLY! Remove lens by turning counterlockwise to disengage the bayonets. Remove the light diffuser by pulling upwards to disengage the clips. Replace lamp and reassemble in reverse order. E22BA3 lamp removal tool is available to aid in lamp removal and installation. Fig. 9 Threaded 3/4” NPT Conduit Mounting Fig. 11 ??? INCANDESCENT LAMP REPLACEMENT Fig. 10 Assembled Stacklight Dimensions Description Catalog No. 12V (BA15d) 6 watts E26S8 24V (BA15d) 6 watts E26S9 48V (BA15d) 6 watts E26S10 110/130V (BA15d) 6 watts E26S11 220/240V (BA15d) 6 watts E26S12 Eaton Corporation Electrical Group 1000 Cherrington Parkway Moon Township, PA 15108 United States 877-ETN-CARE (877-386-2273) Eaton.com © 2008 Eaton Corporation All Rights Reserved Printed in USA Publication No. P24957 / 001 November 2010 PowerChain Management is a registered trademark of Eaton Corporation. All other trademarks are property of their respective owners.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : E4088551 Create Date : 2010:12:01 15:28:26-04:00 Modify Date : 2010:12:01 15:28:26-04:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Creator : E4088551 Title : P24957.indd Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.3.0 (Windows) Document ID : uuid:ce6998ea-19fe-4cfc-8b44-cab8d6dead1a Instance ID : uuid:245b4611-5137-4527-8a50-3c75210530a0 Page Count : 4EXIF Metadata provided by EXIF.tools