How To Fix The Error Code 10

User Manual:

Open the PDF directly: View PDF PDF.
Page Count: 5

DownloadHow To Fix The Error Code 10
Open PDF In BrowserView PDF
USconverters.com
How to fix the error "This Device Cannot Start. (Code 10)"
When working with a USB device in Windows
If you have plugged in a USB device (usually a mass storage device or any type of adapter) into a
computer and it doesn’t work, here are some basic troubleshooting steps to resolve the problem.
First, you want to rule out any problems with the device itself. A good way to do this is to plug the
USB device into a different computer and install the drivers to see if it works there. If it does not
work in a different computer, then the problem is most likely with the device itself. USB devices,
although very handy and portable can fail just like any other device.
However, if the USB device works in another computer system, then the problem likely lies with
the configuration of the computer where the device did not work.
Follow the steps below to troubleshoot this scenario and make your USB device work.
1) If you are using a USB cable with your device, check the cable to make sure it matches the
speed of the device. Use USB 2.0 cables with USB 2.0 devices and USB 1.1 cables with USB 1.1
devices. Swap cables and check the device, if this does not work, proceed to Step 2.
2) Next, open Device Manager and look under the heading for USB Serial Bus Controllers. If
there is a device with a yellow exclamation mark next to it such as USB Mass Storage Device.
Double-click on the entry and check the Device Status. If the status shows something like
"This device cannot start. (Code 10)"
3) If you have downloaded and installed the device drivers using the DriverInstaller first try this:
1. Uninstall the drivers for the device by using the DriverInstaller again.
2. Remove the device from the USB port and reboot your computer.
3. Plug-in the USB device and point the Windows installer to the drivers on the included CD,
instead of using the DriverInstaller.
4) If above steps does not solve the problem try the steps below to remove and reinstall all USB
controllers, (also see guide below).
A. Click on Start
B. Right Click on My Computer, click on Properties
C. Click on the Hardware tab
D. Click the Device Manager button.
E. Expand Universal Serial Bus controllers section.
F. Right-click every device under the Universal Serial Bus controllers node, and then click
Uninstall to remove them one at a time.
G. Restart the computer, and allow the computer to reinstall the USB controllers.
H. Plug in the removable USB device, and then test to make sure that the issue is resolved.
For more information on Troubleshooting USB device problems, visit the Microsoft Support Article
on this subject.

1
WWW.USCONVERTERS.COM

Troubleshooting Network adapter installation
- Device Manager Error Code 10
This document explains how to troubleshoot Code 10 error (on device manager) after you
install the network adapter. To identify the problem, follow these steps:
1. Click Start.
2. Right-click on My Computer and select Properties.
3. Under System Properties, select Hardware tab and select Device Manager.

2
WWW.USCONVERTERS.COM

4. In the Device Manager you will see the adapter you have installed with a Yellow
Exclamation listed in Network adapters category.

3
WWW.USCONVERTERS.COM

5. Double click on the Adapter and check the device status under General tab.

Causes for Code 10:
•
•
•

IRQ conflict
Adapter not plugged in properly (use a different USB port)
Wrong/Incorrect driver installed

4
WWW.USCONVERTERS.COM

Solution:
1. Uninstall adapter drivers by right-clicking on the Adapter and select Uninstall.

2. Turn off computer and remove adapter from the computer.
3. Turn on computer and install drivers again by using the CD or the software you
downloaded for the adapter from the support site.
4. When you are prompted to plug in or insert the adapter, insert the adapter on a
different slot to avoid any conflict with existing devices.
5. If the issue persists, uninstall the drivers from the system.
6. Download the latest drivers for your adapter from www.usconverters.com and
follow installation instructions.
Note: Make sure to download the correct model and version for your adapter.

5
WWW.USCONVERTERS.COM
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 8.0.0 (Windows)
Company                         : xxx
Source Modified                 : D:20091201132129
Creator Tool                    : Acrobat PDFMaker 8.0 for Word
Modify Date                     : 2009:12:01 05:22:19-08:00
Create Date                     : 2009:12:01 05:22:13-08:00
Metadata Date                   : 2009:12:01 05:22:19-08:00
Document ID                     : uuid:f53e1aa5-5700-4ee8-ba3c-66d8ed01b2cc
Instance ID                     : uuid:f7f8805a-fd63-4961-bbd1-ec0b6435f16e
Subject                         : 11
Format                          : application/pdf
Creator                         : xxxx
Title                           : How to fix the error
Page Count                      : 5
Page Layout                     : OneColumn
Language                        : EN-US
Author                          : xxxx
EXIF Metadata provided by EXIF.tools

Navigation menu