ImproX (ECII) Ethernet Controller Impro_ixp400i Impro Ixp400i
User Manual: impro_ixp400i
Open the PDF directly: View PDF 
.
Page Count: 14
| Download | |
| Open PDF In Browser | View PDF |
www.powelltronics.com ImproX EC II ImproX (ECII) Ethernet Advanced Controller Overview Introduction The ImproX (ECII) Ethernet Advanced Controller is a fully Ethernet compatible Controller for use in the IXP400i Access Control System. The Controller boasts both an RS485 Controller Port (Port 1) and an Ethernet Port allowing use of either. When connected to the Ethernet Port the Controller offers communication speeds and capacity not yet seen in similar systems. The Controller comes standard with an RS485 Terminal Port (Port 2) (able to support up to 32 full Antipassback doors), on-board Diagnostic LEDs and a 6 V 3 Ahr System Backup Battery. The Battery allows off-line operation of up to 6 hours. The ImproX (ECII) Ethernet Advanced Controller is the next generation of Ethernet hardware promoting quick and easy installation across a LAN or WAN with bandwidth friendly communication protocol. Key Features Hardware ARM920T Microprocessor Core operating at 200 mips (million instructions per second). Linux Operating System. 64 MB SDRAM Memory. 8 MB Flash Memory. LEDs indicate transmit and receive line activity for diagnostics. A Real Time Clock (RTC) with a 3 V Lithium Backup Battery (providing 5 years stand-by operation). Remote Firmware download capability. 1 Part Number: XEC900-0-0-GB-XX Supports a secure logon when changing Controller Configuration settings using the Ethernet Discovery Utility software. An Ethernet Controller Port for connection to an Ethernet Switch or Hub (or other network device). An RS485 Controller Bus Port for connection to other ImproX (ECII) Ethernet Controllers. An RS485 Terminal Bus Port for connection to up to 64 Terminal Fixed Addresses. Operation from power inputs in the range 10 V DC to 30 V DC. Configurable, dynamic memory capable of storing up to 300 000 Tagholders and up to 1 000 000 buffered transactions. Robust, Aluminium enclosure. Fully incorporated uninterrupted Power Supply with trickle charge and battery management. Incorporated 6 V 3 Ahr Sealed Lead Acid Battery providing 6 hours full operation. Power Input Fail and Battery Low signal reporting. 48 Hour Hibernation Mode for extended battery backup of the ImproX (EC II) Ethernet Controllers database (including transactions). When used with ImproNet V7.4 Software Tags per person: 8. Tagholder Access Groups per Tag: 10. Access Groups total: 10 000. Active System Events: 8 000. Actions: 50 000. Approvals CE Approved. FCC Approval Pending. 2 Part Number: XEC900-0-0-GB-XX Specifications Physical Dimensions Length : 168 mm (7 in). Width : 197 mm (8 in). Height : 89 mm (4 in). Approximate Weight : 2 kg (4 lb) Battery included. Cabinet Material : Aluminium. Colour : Black. Operating : -10 C to +50 C (+14 F to +122 F). Storage : -15 C to +50 C (+5 F to +122 F). Humidity Range : Approvals (Test Information) : Dust and Splash Resistance : Drop Endurance : 0 to 95% relative humidity at +40 C (+104 F) noncondensing. EN 301 489-3 EN 304 489-1 Designed to work in an indoor (dry) environment similar to IP30. The Controller is, therefore, NOT sealed against water. 2 m (7 ft) drop (in packaging). : 10 V DC to 30 V DC. Environmental Temperature o o o o o o o o o o Electrical Power Requirements Input Voltage Current (mA) Power (W) : 420 4.2 : 140 4.2 : 1 V PP at 50 Hz. : Reverse polarity on DC power inputs, over-voltage and over-current protection are provided on the Controller. Connection : Protocol : Standard Ethernet RJ45 connector. 10/100 Mbps, half or full duplex. TCP/IP, UDP. Power Requirements Supply Voltage 10 V DC (Maximum) Supply Voltage 30 V DC (Maximum) Permissible Input Supply Ripple Voltage (Max) Power Input Protection Ethernet Port 3 Part Number: XEC900-0-0-GB-XX NOTE: The RS485 1 (Controller) Port connection details only apply to ImproX ECII Controllers with Firmware V7.16 upwards. RS485 1 (Controller) Port Configuration : 38 400 Default. Electrical Interface : RS485. Baud Rates : Data Format : 9 600, 19 200, 28 800, 38 400 and 57 600 selectable via the Communications Protocol. 8 data bits, no parity, 1 stop bit. Communications Protocol : ImproX Secure Communications Protocol. Line Termination : Provision is made for line termination. Default Mode : Receive Mode. Configuration : 38 400 Default. Electrical Interface : RS485. Baud Rates : Data Format : 9 600, 19 200, 28 800, 38 400, 57 600 and 76 800 selectable via the Protocol. 8 data bits, no parity, 1 stop bit. Communications Protocol : ImproX Secure Communications Protocol. Line Termination : Provision is made for line termination. Default Mode : Receive Mode. RAM (Non-volatile) : 64 MBytes. Flash ROM : 8 MBytes. : 1 x 3 V, CR2032, Lithium cell Battery. : 5 Years (with power OFF). : 6 V 3 Ahr Sealed Lead Acid Battery. Length : 133 mm (5 in). Width : 34 mm (1 in). Height RS485 2 (Terminal) Port Memory Real Time Clock (RTC) Backup Battery Battery Type Battery Life System Battery Battery Type Size : 65 mm (3 in) (Including the terminals). Approximate Weight : 650 g (23 oz). Battery Life : : 4-6 Hours uninterrupted operation. 48 Hours Power Shutdown (Hibernation Mode). 2 Internal switches. : RAM, Flash-ROM, RTC. RS485 1 (Controller) Port : 38 400. RS485 2 (Terminal) Port : 38 400. Anti-tamper Protection Factory Default Settings Test Modes Power-on Self-test Baud Rate 4 Part Number: XEC900-0-0-GB-XX Operator or Installer Interfaces Diagnostic LED Indicators Power-on LED : Red LED (internally visible). Incoming RS485 1 (Controller) : Flashing Green LED (internally visible). Outgoing RS485 1 (Controller) : Flashing Red LED (internally visible). Incoming RS485 2 (Terminal) : Flashing Green LED (internally visible). Outgoing RS485 2 (Terminal) : Flashing Red LED (internally visible). Link Speed LED (Ethernet) : Flashing Red LED (internally visible). Duplex Mode LED (Ethernet) : Flashing Red LED (internally visible). Link Active LED (Ethernet) : Flashing Red LED (internally visible). CPU Usage : CPU Running : CPU Fault : Red LED (internally visible). On = Idle, Off = Busy. Red LED (internally visible). On = Yes, Off = No. Red LED (internally visible). On = Fault Condition, Off = Ok. Installation Information Accessories Find the following when unpacking the Controller: II An ImproX EC Controller housed in a Black, powder coated, Aluminium extruded Cabinet. The Cabinet consists of a Top Cover and a Base sealed at each end with a Mild Steel End Plate, secured with 5 Thread Cutter Screws (M3 x 8 mm). A 6 V 3 Ahr Sealed Lead Acid Backup Battery (Installed). A 3 V, CR2032, Lithium cell Battery. Four Wood Screws (3.5 mm x 25 mm). Four Wall Plugs (7 mm). A MAC Address Label. An extra Fixed Address Label. 5 Part Number: XEC900-0-0-GB-XX General II Remember the following when installing your ImproX EC Controller: Communications Distance RS485 1 (Controller Port) and RS485 2 (Terminal Port) II The RS485 communications distance between the ImproX EC Controller and the LAST ImproX Unit in a cable run, MUST NOT exceed 1 km (1 090 yd). Achieve this by using good quality screened twisted pair Mylar cable, EARTHED on one side. Ethernet Port The Ethernet Controller plugs into an Ethernet Switch or Hub (or other network device), cable runs for this must conform to ethernet cabling specifications. Termination Resistors for RS485 Bus Communications Long transmission lines or multiple “star” connections, may cause communication problems. Placing the Terminating Resistor Jumper Link in the LAST UNIT AT THE END OF THE CABLE RUN should solve the problem (depending on the bus). Refer to Figure 1 on page 8. EARTH Connection II In conditions where excessive noise is present connect the ImproX EC Controller to a good EARTH point. Using either of the RS485 Ports, connect the EARTH Lead to the “SHD” Terminal. Mains II EARTH can be used, but electrical noise may persist. The EARTH Lead to the ImproX EC Controller 2 2 should have a minimum cross-sectional area of 1 mm (0.001 in ) and can be either solid or stranded. First Time Use of the Controller CAUTION: Insert the supplied 3 V Lithium Real Time Clock Backup Battery into the Battery II Holder BEFORE powering up the ImproX EC Controller. Installing the Real Time Clock Backup Battery The Battery Holder is located in the bottom right-hand side of the ImproX ECII Controllers Printed Circuit Board (PCB), directly above the RS485 2 (Terminal Port). 1. Remove the Controllers Top Cover. 2. Slide the supplied 3 V, CR2032, Lithium cell Battery under the metal clip of the Battery Holder, with the "+" Terminal facing UP. 3. Pull the plastic clip AWAY from the Battery Holder and press the Battery firmly into the Battery Holder. 6 Part Number: XEC900-0-0-GB-XX Connecting the System Backup Battery 1. Attach the Battery Fly Lead to the System Backup Battery Connector (see Figure 1 for Key Component Positions). 2. Attach the Controller’s Top Cover. Mounting the Controller CAUTION: Make certain that you mount the Controller on a vibration-free surface. II Select the mounting position of the ImproX EC Controller, considering accessibility and routing of wires. Secure the Controller to the mounting surface, using four suitable screws and wall plugs (supplied), nuts and bolts or rivets. Replacing the 6 V 3 Ahr Lead Acid System Backup Battery 1. Remove the Controller’s Top Cover. 2. Remove the Controller’s back End Plate. 3. Disconnect the Battery Fly Lead Spade Terminals from the old Battery. 4. Slide the old Battery out of the Battery Compartment. CAUTION: Ensure that you maintain the correct polarity of the Battery Fly Lead Spade Terminals. Red wire to Positive (+) and Black wire to Negative (-). 5. Slide the new Battery into the Battery Compartment. 6. Reconnect the Battery Fly Lead Spade Terminals to the new Battery. 7. Attach the Controller’s back End Plate. 8. Attach the Controller’s Top Cover. 7 Part Number: XEC900-0-0-GB-XX Electrical Connections Controller Layout Figure 1: Key Component Positions 8 Part Number: XEC900-0-0-GB-XX Connecting the ImproX ECII Controller II Figure 2 and Figure 3 show the ImproX EC Controllers relationship with the rest of the ImproX product range. Figure 2: Ethernet Configuration Diagram 9 Part Number: XEC900-0-0-GB-XX Figure 3: RS485 Configuration Diagram 10 Part Number: XEC900-0-0-GB-XX II Figure 4 shows typical connection options for the ImproX EC Controller. Figure 4: Typical Electrical Connections NOTE: DO NOT connect (daisy chain) additional RS485 Controllers on Port 2, as the System will NOT Auto-ID these Controllers. 11 Part Number: XEC900-0-0-GB-XX Power Shutdown The ImproX ECII Controller’s 6 V 3 Ahr Sealed Lead Acid Backup Battery provides between 4-6 hours of uninterrupted power. Five minutes after the Battery Low signals received by the Controller, the Controller switches to Hibernation Mode (low power). Hibernation Mode provides a further 48 hours of database (including transactions) memory retention. Master Reset The ImproX ECII Controller can be restarted manually, without removing the power connections, by pressing the Master Reset button (See Figure 1 for Key Component Positions).. Restoring Factory Default Settings If you assign an invalid IP address to the ImproX ECII Controller, it will not be able to communicate. To correct the problem, restore the Controllers factory default settings as follows: CAUTION: This will restore the firmware to the version set when shipped from the factory. If you have upgraded the Controllers firmware since installation, ensure that you upgrade again immediately. 1. Power up the ImproX ECII Controller. 2. After 30 seconds, place a link across the pins of the Factory Default Jumper Link (LK4). (See Figure 1 for Key Component Positions). 3. After 5 seconds, remove the Link. 12 Part Number: XEC900-0-0-GB-XX Unit Address Information Fixed Address Label The last 8 digits of the MAC Address, that is 4A-9A-BC-3D (see Figure 5), translate to the products Fixed Address used by the System Software. Attach the loose Fixed Address Label (packaged with the Controller) in position on the Unit Location Chart (or your sketched site plan). MAC Address Label II Each ImproX EC Controller is supplied with a separate MAC Address Label, much like the one shown in Figure 5, which uniquely identifies each Controller. Attach the extra loose MAC Address Label, alongside the Fixed Address Label, to the Unit Location Chart enclosed (or your sketched site plan). Figure 5: Sample MAC Address Label When the system installation is complete and all the units are represented on the Unit Location Chart (or your sketched site plan) by their Fixed Address and MAC Address Labels, file the document for future reference. IP Address NOTE: All ImproX ECII Controllers have the same IP Address (192.168.100.1). In the absence of a DHCP server, plug each Controller into the network individually and set the static IP Address. 13 Part Number: XEC900-0-0-GB-XX Guarantee or Warranty This product conforms to our Guarantee or Warranty details placed on our Web Site, to read further please go to www.impro.net. Ordering Information II Order the ImproX (EC ) Ethernet Controller using the XEC900-0-0-GB-XX Impro part number. II This manual is applicable to the ImproX (EC ) Ethernet Controller, XEC900-0-0-GB-03. (The last two digits of the Impro stock code indicate the issue status of the product). XEC350-0-0-GB-02 Issue 03 May 2008 ImproX ECII\Product Specification Catalogue\ LATEST ISSUE\XECII-psc-en-03.docx 14
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Tagged PDF : No Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2008:05:27 08:04:07Z Creator Tool : Microsoft® Office Word 2007 Modify Date : 2008:11:14 11:52:57+02:00 Metadata Date : 2008:11:14 11:52:57+02:00 Format : application/pdf Description : ImproX (ECII) Ethernet Controller Creator : Shannon Frances Title : ImproX (ECII) Ethernet Controller Producer : Microsoft® Office Word 2007 Document ID : uuid:79d4f8f4-c4cd-4f90-8c99-04d8fbf3d005 Instance ID : uuid:40819906-223c-4c00-9bd5-28104d316e43 Has XFA : No Page Count : 14 Page Layout : SinglePage Language : en-US Subject : ImproX (ECII) Ethernet Controller Author : Shannon Frances Keywords : ImproX, (ECII), Ethernet, ControllerEXIF Metadata provided by EXIF.tools