DsPIC33/PIC24 Family Reference Manual, Liquid Crystal Display (LCD) Lcd Manual
User Manual:
Open the PDF directly: View PDF 
.
Page Count: 44
| Download | |
| Open PDF In Browser | View PDF |
Liquid Crystal Display (LCD) HIGHLIGHTS This section of the manual contains the following major topics: 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 Introduction ....................................................................................................................... 2 LCD Registers................................................................................................................... 3 LCD Segment Pins Configuration ..................................................................................... 6 LCD Clock Source Selection............................................................................................. 8 LCD Bias Types ................................................................................................................ 9 LCD Multiplex Types ....................................................................................................... 21 Segment Enables............................................................................................................ 22 Pixel Control.................................................................................................................... 22 LCD Frame Frequency ................................................................................................... 22 LCD Waveform Generation............................................................................................. 22 LCD Interrupts................................................................................................................. 36 Configuring the LCD Module........................................................................................... 38 Operation During Sleep .................................................................................................. 39 Registers......................................................................................................................... 40 Revision History .............................................................................................................. 41 2010-2013 Microchip Technology Inc. DS30009740B-page 1 dsPIC33/PIC24 Family Reference Manual 1.0 INTRODUCTION The Liquid Crystal Display (LCD) driver module generates the timing control to drive a Static or Multiplexed LCD panel. In the 100-pin devices (PIC24FJXXXGA3XX), the module drives panels of up to eight commons and up to 60 segments when 5 to 8 commons are used, and up to 64 segments when 1 to 4 commons are used. It also provides control of the LCD pixel data. The LCD driver module supports: • Direct driving of LCD panel • Three LCD clock sources with selectable prescaler • Up to eight commons: - Static (one common) - 1/2 Multiplex (two commons) - 1/3 Multiplex (three commons) - 1/8 Multiplex (eight commons) • Up to 60 segments (in 100-pin devices when 1/5-1/8 Multiplex is selected), 64 (in 100-pin devices when up to 1/4 Multiplex is selected), 46 (in 80-pin devices when 1/5-1/8 Multiplex is selected), 50 (in 80-pin devices when up to 1/4 Multiplex is selected), 30 (in 64-pin devices when 1/5-1/8 Multiplex is selected) and 34 (in 64-pin devices when up to 1/4 Multiplex is selected) • Static, 1/2 or 1/3 LCD Bias • On-chip Bias generator with dedicated charge pump to support a range of fixed and variable Bias options • Internal resistors for Bias voltage generation • Software contrast control for LCD using the internal biasing A simplified block diagram of the module is shown in Figure 1-1. Figure 1-1: LCD Driver Module Block Diagram Data Bus LCD DATA 32 x 16 (= 8x 64) 16 LCDDATA31 512 LCDDATA30 . . . to 64 LCDDATA1 MUX 64 SEG<63:0> LCDDATA0 Bias Voltage To I/O Pins Timing Control LCDCON 8 LCDPS LCDSEx COM<7:0> LCD Bias Generation Resistor Ladder FRC Oscillator LPRC Oscillator SOSC (Secondary Oscillator) DS30009740B-page 2 LCD Clock Source Select LCD Charge Pump 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) 2.0 LCD REGISTERS The LCD driver module has 40 registers: • • • • • • LCD Control Register (LCDCON) LCD Phase Register (LCDPS) LCD Voltage Regulator Control Register (LCDREG) LCD Reference Ladder Control Register (LCDREF) Four LCD Segment Enable Registers (LCDSE3:LCDSE0) 32 LCD Data Registers (LCDDATA31:LCDDATA0) The LCDCON register, shown in Register 2-1, controls the overall operation of the module. Once the module is configured, the LCDEN (LCDCON<15>) bit is used to enable or disable the LCD module. The LCD panel can also operate during Sleep by clearing the SLPEN (LCDCON<6>) bit. The LCDPS register, shown in Register 2-2, configures the LCD clock source prescaler and the type of waveform: Type-A or Type-B. For details on these features, see Section 4.0 “LCD Clock Source Selection”, Table 14-1 and Section 10.0 “LCD Waveform Generation”. 2010-2013 Microchip Technology Inc. DS30009740B-page 3 dsPIC33/PIC24 Family Reference Manual Register 2-1: LCDCON: LCD Control Register R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 LCDEN — LCDSIDL — — — — — bit 15 bit 8 U-0 R/W-0 R/C-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — SLPEN WERR CS1 CS0 LMUX2 LMUX1 LMUX0 bit 7 bit 0 Legend: C = Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 LCDEN: LCD Driver Enable bit 1 = LCD driver module is enabled 0 = LCD driver module is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 LCDSIDL: LCD Stop in CPU Idle Mode Control bit 1 = LCD driver halts in CPU Idle mode 0 = LCD driver continues to operate in CPU Idle mode bit 12-7 Unimplemented: Read as ‘0’ bit 6 SLPEN: LCD Driver Enable in Sleep Mode bit 1 = LCD driver module is disabled in Sleep mode 0 = LCD driver module is enabled in Sleep mode bit 5 WERR: LCD Write Failed Error bit 1 = LCDDATAx register is written while WA (LCDPS<4>) = 0 (must be cleared in software) 0 = No LCD write error bit 4-3 CS<1:0>: Clock Source Select bits 00 = FRC 01 = LPRC 1x = SOSC bit 2-0 LMUX<2:0>: LCD Commons Select bits LMUX<2:0> Multiplex Bias 111 1/8 MUX (COM<7:0>) 1/3 110 1/7 MUX (COM<6:0>) 1/3 101 1/6 MUX (COM<5:0>) 1/3 100 1/5 MUX (COM<4:0>) 1/3 011 1/4 MUX (COM<3:0>) 1/3 010 1/3 MUX (COM<2:0>) 1/2 or 1/3 001 1/2 MUX (COM<1:0>) 1/2 or 1/3 000 Static (COM0) Static DS30009740B-page 4 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Register 2-2: LCDPS: LCD Phase Register U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0 WFT BIASMD LCDA WA LP3 LP2 LP1 LP0 bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-8 Unimplemented: Read as ‘0’ bit 7 WFT: Waveform Type Select bit 1 = Type-B waveform (phase changes on each frame boundary) 0 = Type-A waveform (phase changes within each common type) bit 6 BIASMD: Bias Mode Select bit When LMUX<2:0> = 000 or 011-111: 0 = Static Bias mode/1/3 Bias mode (do not set this bit to ‘1’) When LMUX<2:0> = 001 or 010: 1 = 1/2 Bias mode 0 = 1/3 Bias mode bit 5 LCDA: LCD Active Status bit 1 = LCD driver module is active 0 = LCD driver module is inactive bit 4 WA: LCD Write Allow Status bit 1 = Write into the LCDDATAx registers is allowed 0 = Write into the LCDDATAx registers is not allowed bit 3-0 LP<3:0>: LCD Prescaler Select bits 1111 = 1:16 1110 = 1:15 1101 = 1:14 1100 = 1:13 1011 = 1:12 1010 = 1:11 1001 = 1:10 1000 = 1:9 0111 = 1:8 0110 = 1:7 0101 = 1:6 0100 = 1:5 0011 = 1:4 0010 = 1:3 0001 = 1:2 0000 = 1:1 2010-2013 Microchip Technology Inc. x = Bit is unknown DS30009740B-page 5 dsPIC33/PIC24 Family Reference Manual 3.0 LCD SEGMENT PINS CONFIGURATION The LCDSEx registers configure the functions of the port pins. Setting the segment enable bit for a particular segment configures that pin as an LCD driver. There are four LCD Segment Enable registers, as shown in Table 3-1. The prototype LCDSEx register is shown in Register 3-1. Table 3-1: LCDSEx Registers and Associated Segments Register Segments LCDSE0 Seg 15:Seg 0 LCDSE1 Seg 31:Seg 16 LCDSE2 Seg 47:Seg 32 LCDSE3 Seg 63:Seg 48 Once the module is initialized for the LCD panel, the individual bits of the LCDDATAx registers are cleared, or set, to represent a clear or dark pixel, respectively. Specific sets of LCDDATAx registers are used with specific segments and common signals. Each bit represents a unique combination of a specific segment connected to a specific common. Individual LCDDATAx bits are named by the convention, “SxxCy”, with “xx” as the segment number and “y” as the common number. The relationship is summarized in Register 2-2. The prototype LCDDATAx register is shown in Register 3-2. Note: Register 3-1: Not all LCDSEx and LCDDATAx registers are implemented in all devices. Refer to the specific device data sheet for more details. LCDSEx: LCD Segment x Enable Register R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SE(n+15) SE(n+14) SE(n+13) SE(n+12) SE(n+11) SE(n+10) SE(n+9) SE(n+8) bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SE(n+7) SE(n+6) SE(n+5) SE(n+4) SE(n+3) SE(n+2) SE(n+1) SE(n) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 7-0 x = Bit is unknown SE(n + 15):SE(n): Segment Enable bits For LCDSE0: n = 0 For LCDSE1: n = 16 For LCDSE2: n = 32 For LCDSE3: n = 48 1 = Segment function of the pin is enabled; digital I/O is disabled 0 = Segment function of the pin is disabled DS30009740B-page 6 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Register 3-2: LCDDATAx: LCD Data x Register R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 S(n+15)Cy S(n+14)Cy S(n+13)Cy S(n+12)Cy S(n+11)Cy S(n+10)Cy S(n+9)Cy S(n+8)Cy bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 S(n+7)Cy S(n+6)Cy S(n+5)Cy S(n+4)Cy S(n+3)Cy S(n+2)Cy S(n+1)Cy S(n)Cy bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15-0 Table 3-2: x = Bit is unknown S(n + 15)Cy:S(n)Cy: Pixel On bits For registers, LCDDATA0 through LCDDATA3: n = (16x), y = 0 For registers, LCDDATA4 through LCDDATA7: n = (16(x – 4)), y = 1 For registers, LCDDATA8 through LCDDATA11: n = (16(x – 8)), y = 2 For registers, LCDDATA12 through LCDDATA15: n = (16(x – 12)), y = 3 For registers, LCDDATA16 through LCDDATA19: n = (16(x – 16)), y = 4 For registers, LCDDATA20 through LCDDATA23: n = (16(x – 20)), y = 5 For registers, LCDDATA24 through LCDDATA27: n = (16(x – 24)), y = 6 For registers, LCDDATA28 through LCDDATA31: n = (16(x – 28)), y = 7 1 = Pixel on 0 = Pixel off LCDDATAx Registers and Bits for Segment and COM Combinations Segments COM Lines 0 to 15 16 to 31 32 to 47 48 to 64 0 LCDDATA0 S00C0:S15C0 LCDDATA1 S16C0:S31C0 LCDDATA2 S32C0:S47C0 LCDDATA3 S48C0:S63C0 1 LCDDATA4 S00C1:S15C1 LCDDATA5 S16C1:S31C1 LCDDATA6 S32C1:S47C1 LCDDATA7 S48C1:S63C1 2 LCDDATA8 S00C2:S15C2 LCDDATA9 S16C2:S31C2 LCDDATA10 S32C2:S47C2 LCDDATA11 S48C2:S63C2 3 LCDDATA12 S00C3:S15C3 LCDDATA13 S16C3:S31C3 LCDDATA14 S32C3:S47C3 LCDDATA15 S48C3:S63C3 4 LCDDATA16 S00C4:S15C4 LCDDATA17 S16C4:S31C4 LCDDATA18 S32C4:S47C4 LCDDATA19 S48C4:S59C4 5 LCDDATA20 S00C5:S15C5 LCDDATA21 S16C5:S31C5 LCDDATA22 S32C5:S47C5 LCDDATA23 S48C5:S69C5 6 LCDDATA24 S00C6:S15C6 LCDDATA25 S16C6:S31C6 LCDDATA26 S32C6:S47C6 LCDDATA27 S48C6:S59C6 7 LCDDATA28 S00C7:S15C7 LCDDATA29 S16C7:S31C7 LCDDATA30 S32C7:S47C7 LCDDATA31 S48C7:S59C7 2010-2013 Microchip Technology Inc. DS30009740B-page 7 dsPIC33/PIC24 Family Reference Manual 4.0 LCD CLOCK SOURCE SELECTION The LCD driver module has three possible clock sources: • FRC/8192 • SOSC Clock/32 • LPRC/32 The first clock source is the 8 MHz Fast Internal RC (FRC) oscillator, divided by 8,192. This divider ratio is chosen to provide about 1 kHz output. The divider is not programmable. Instead, the LCD Prescaler bits, LCDPS<3:0>, are used to set the LCD frame clock rate. The second clock source is the SOSC oscillator/32. This also outputs about 1 kHz when a 32.768 kHz crystal is used with the SOSC oscillator. To use the SOSC oscillator as a clock source, set the SOSCEN (OSCCON<1>) bit. The third clock source is a 31.25 kHz internal LPRC oscillator/32 that provides approximately 1 kHz output. The second and third clock sources may be used to continue running the LCD while the processor is in Sleep. These clock sources are selected through the bits, CS<1:0> (LCDCON<4:3>). 4.1 LCD Prescaler A 16-bit counter is available as a prescaler for the LCD clock. The prescaler is not directly readable or writable. Its value is set by the LP<2:0> bits (LCDPS<2:0>) that determine the prescaler assignment and prescale ratio. Selectable prescale values are from 1:1 through 1:16, in increments of one. LCD Clock Generation FRC Oscillator (8 MHZ) SOSC Oscillator (32 kHz) LPRC Oscillator (31.25 kHz) ÷8192 ÷32 ÷4 STAT ÷2 1/2 MUX 4-Bit Prog Prescaler ÷1, 2, 3....8 Ring Counter MUX ÷32 CS<1:0> (LCDCON<4:3>) DS30009740B-page 8 COM0 COM1 COM2 COM7 Figure 4-1: LP<2:0> (LCDPS<2:0>) LMUX<2:0> (LCDCON<2:0>) LMUX<2:0> (LCDCON< 2:0>) 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) 5.0 LCD BIAS TYPES The LCD module can be configured in one of three Bias types: • Static Bias (Two Voltage Levels: VSS and VDD) • 1/2 Bias (Three Voltage Levels: VSS, 1/2 VDD and VDD) • 1/3 Bias (Four Voltage Levels: VSS, 1/3 VDD, 2/3 VDD and VDD) LCD Bias voltages can be generated with an internal resistor ladder, internal Bias generator or external resistor ladder. 5.1 Internal Resistor Biasing This mode does not use external resistors, but rather internal resistor ladders that are configured to generate the Bias voltage. The internal reference ladder actually consists of three separate ladders. Disabling the internal reference ladder disconnects all of the ladders, allowing external voltages to be supplied. Depending on the total resistance of the resistor ladders, the biasing can be classified as low, medium or high power. Table 5-1 shows the total resistance of each of the ladders. Figure 5-1 shows the internal resister ladder connections. When the internal resistor ladder is selected, the Bias voltage will be internal; it can also provide software contrast control (using LCDCST<2:0>). Table 5-1: Internal Resistance Ladder Power Modes Power Mode Low Nominal Resistance of Entire Ladder IDD 3 MΩ 1 µA Medium 300 kΩ 10 µA High 30 kΩ 100 µA 2010-2013 Microchip Technology Inc. DS30009740B-page 9 dsPIC33/PIC24 Family Reference Manual Figure 5-1: LCD Bias Internal Resistor Ladder Connection Diagram VDD LCDIRE LCDCST<2:0> VLCD3PE LCDBIAS3 VLCD2PE LCDBIAS2 VLCD1PE LCDBIAS1 Low Resistor Ladder Medium Resistor Ladder High Resistor Ladder A Power Mode B Power Mode LRLAT<2:0> LRLAP<1:0> LRLBP<1:0> There are two power modes, designated as “Mode A” and “Mode B”. Mode A is set by the bits, LRLAP<1:0>, and Mode B by the LRLBP<1:0> bits. The resistor ladder to use for Modes A and B are selected by the bits, LRLAP<1:0> and LRLBP<1:0>, respectively. Each ladder has a matching contrast control ladder, tuned to the nominal resistance of the reference ladder. This contrast control resistor can be controlled by the LCDCST<2:0> bits (LCDREF<13:11>). Disabling the internal reference ladder results in all of the ladders being disconnected, allowing external voltages to be supplied. To get additional current in High-Power mode, when LRLAP<1:0> (LCDREF<7:6>) = 11, both the medium and high-power resistor ladders are activated. Whenever the LCD module is inactive (LCDA (LCDPS<5>) = 0), the reference ladder will be turned off. DS30009740B-page 10 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) 5.1.1 AUTOMATIC POWER MODE SWITCHING As an LCD segment is electrically only a capacitor, current is drawn only during the interval when the voltage is switching. To minimize total device current, the LCD reference ladder can be operated in a different power mode for the transition portion of the duration. This is controlled by the LCDREF register. Mode A Power mode is active for a programmable time, beginning at the time when the LCD segment waveform is transitioning. The LRLAT<2:0> (LCDREF<2:0>) bits select how long the transition or if the Mode A is active. Mode B Power mode is active for the remaining time before the segments or commons change again. As shown in Figure 5-2, there are 32 counts in a single segment time. Type-A can be chosen during the time when the waveform is in transition. Type-B can be used when the clock is stable or not in transition. By using this feature of automatic power switching using Type-A/Type-B, the power consumption can be optimized for a given contrast. Figure 5-2: LCD Reference Ladder Power Mode Switching Diagram Single Segment Time lcd_32x_clk cnt<4:0> ‘H00 ‘H01 ‘H02 ‘H03 ‘H04 ‘H05 ‘H06 ‘H07 ‘H1E ‘H1F ‘H00 ‘H01 lcd_clk ‘H3 LRLAT<2:0> Segment Data LRLAT<2:0> Power Mode Power Mode A 2010-2013 Microchip Technology Inc. Power Mode B Mode A DS30009740B-page 11 dsPIC33/PIC24 Family Reference Manual 5.1.2 CONTRAST CONTROL The LCD contrast control circuit consists of a 7-tap resistor ladder, controlled by the LCDCST<2:0> bits (see Figure 5-3). Figure 5-3: Internal Reference and Contrast Control Block Diagram 7 Stages VDD R R R R Analog MUX 7 To Top of Reference Ladder 0 LCDCST<2:0> 3 Internal Reference 5.1.3 Contrast Control INTERNAL REFERENCE Under firmware control, an internal reference for the LCD Bias voltages can be enabled. When enabled, the source of this voltage can be VDD. When no internal reference is selected, the LCD contrast control circuit is disabled and the LCD Bias must be provided externally. Whenever the LCD module is inactive (LCDA = 0), the internal reference will be turned off. 5.1.4 VLCDxPE PINS The VLCD3PE, VLCD2PE and VLCD1PE pins provide the ability for an external LCD Bias network to be used instead of the internal ladder. Use of the VLCDxPE pins does not prevent use of the internal ladder. Each VLCDxPE pin has an independent control in the LCDREF register, allowing access to any or all of the LCD Bias signals. This architecture allows for maximum flexibility in different applications. The VLCDxPE pins could be used to add capacitors to the internal reference ladder for increasing the drive capacity. For applications where the internal contrast control is insufficient, the firmware can choose to enable only the VLCD3PE pin, allowing an external contrast control circuit to use the internal reference divider. DS30009740B-page 12 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Register 5-1: LCDREF: LCD Reference Ladder Control Register R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 LCDIRE — LCDCST2 LCDCST1 LCDCST0 VLCD3PE VLCD2PE VLCD1PE bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 LRLAP1 LRLAP0 LRLBP1 LRLBP0 — LRLAT2 LRLAT1 LRLAT0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 LCDIRE: LCD Internal Reference Enable bit 1 = Internal LCD reference is enabled and connected to the internal contrast control circuit 0 = Internal LCD reference is disabled bit 14 Unimplemented: Read as ‘0’ bit 13-11 LCDCST<2:0>: LCD Contrast Control bits Selects the Resistance of the LCD Contrast Control Resistor Ladder: 111 = Resistor ladder is at maximum resistance (minimum contrast) 110 = Resistor ladder is at 6/7th of maximum resistance 101 = Resistor ladder is at 5/7th of maximum resistance 100 = Resistor ladder is at 4/7th of maximum resistance 011 = Resistor ladder is at 3/7th of maximum resistance 010 = Resistor ladder is at 2/7th of maximum resistance 001 = Resistor ladder is at 1/7th of maximum resistance 000 = Minimum resistance (maximum contrast); resistor ladder is shorted bit 10 VLCD3PE: LCD Bias 3 Pin Enable bit 1 = Bias 3 level is connected to the external pin, LCDBIAS3 0 = Bias 3 level is internal (internal resistor ladder) bit 9 VLCD2PE: LCD Bias 2 Pin Enable bit 1 = Bias 2 level is connected to the external pin, LCDBIAS2 0 = Bias 2 level is internal (internal resistor ladder) bit 8 VLCD1PE: LCD Bias 1 Pin Enable bit 1 = Bias 1 level is connected to the external pin, LCDBIAS1 0 = Bias 1 level is internal (internal resistor ladder) bit 7-6 LRLAP<1:0>: LCD Reference Ladder A Time Power Control bits During Time Interval A: 11 = Internal LCD reference ladder is powered in High-Power mode 10 = Internal LCD reference ladder is powered in Medium Power mode 01 = Internal LCD reference ladder is powered in Low-Power mode 00 = Internal LCD reference ladder is powered down and unconnected bit 5-4 LRLBP<1:0>: LCD Reference Ladder B Time Power Control bits During Time Interval B: 11 = Internal LCD reference ladder is powered in High-Power mode 10 = Internal LCD reference ladder is powered in Medium Power mode 01 = Internal LCD reference ladder is powered in Low-Power mode 00 = Internal LCD reference ladder is powered down and unconnected bit 3 Unimplemented: Read as ‘0’ 2010-2013 Microchip Technology Inc. DS30009740B-page 13 dsPIC33/PIC24 Family Reference Manual Register 5-1: bit 2-0 LCDREF: LCD Reference Ladder Control Register (Continued) LRLAT<2:0>: LCD Reference Ladder A Time Interval Control bits Sets the number of 32 clock counts when the A Time Interval Power mode is active. For Type-A Waveforms (WFT = 0): 111 = Internal LCD reference ladder is in A Power mode for 7 clocks and B Power mode for 9 clocks 110 = Internal LCD reference ladder is in A Power mode for 6 clocks and B Power mode for 10 clocks 101 = Internal LCD reference ladder is in A Power mode for 5 clocks and B Power mode for 11 clocks 100 = Internal LCD reference ladder is in A Power mode for 4 clocks and B Power mode for 12 clocks 011 = Internal LCD reference ladder is in A Power mode for 3 clocks and B Power mode for 13 clocks 010 = Internal LCD reference ladder is in A Power mode for 2 clocks and B Power mode for 14 clocks 001 = Internal LCD reference ladder is in A Power mode for 1 clock and B Power mode for 15 clocks 000 = Internal LCD reference ladder is always in B Power mode For Type-B Waveforms (WFT = 1): 111 = Internal LCD reference ladder is in A Power mode for 7 clocks and B Power mode for 25 clocks 110 = Internal LCD reference ladder is in A Power mode for 6 clocks and B Power mode for 26 clocks 101 = Internal LCD reference ladder is in A Power mode for 5 clocks and B Power mode for 27 clocks 100 = Internal LCD reference ladder is in A Power mode for 4 clocks and B Power mode for 28 clocks 011 = Internal LCD reference ladder is in A Power mode for 3 clocks and B Power mode for 29 clocks 010 = Internal LCD reference ladder is in A Power mode for 2 clocks and B Power mode for 30 clocks 001 = Internal LCD reference ladder is in A Power mode for 1 clock and B Power mode for 31 clocks 000 = Internal LCD reference ladder is always in B Power mode 5.2 LCD Bias Generation The LCD driver module is capable of generating the required Bias voltages for LCD operation with a minimum of external components. This includes the ability to generate the different voltage levels required by the different Bias types that are required by the LCD. The driver module can also provide Bias voltages, both above and below the microcontroller VDD, through the use of an on-chip LCD voltage regulator. 5.2.1 LCD BIAS TYPES There is support for three Bias types based on the waveforms generated to control segments and commons: • Static (two discrete levels) • 1/2 Bias (three discrete levels • 1/3 Bias (four discrete levels) The use of different waveforms in driving the LCD is discussed in more detail in Section 10.0 “LCD Waveform Generation”. 5.2.2 LCD VOLTAGE REGULATOR The purpose of the LCD regulator is to provide proper Bias voltage and good contrast for the LCD, regardless of VDD levels. This module contains a charge pump and internal voltage reference. The regulator can be configured by using external components to boost Bias voltage above VDD. It can also operate a display at a constant voltage below VDD. The regulator can also be selectively disabled to allow Bias voltages to be generated by an external resistor network. The LCD regulator is controlled through the LCDREG register (Register 5-2). It is enabled or disabled using the CKSEL<1:0> bits, while the charge pump can be selectively enabled using the CPEN bit. When the regulator is enabled, the MODE13 bit is used to select the Bias type. The peak LCD Bias voltage, measured as a difference between the potentials of LCDBIAS3 and LCDBIAS0, is configured with the BIAS<2:0> bits. DS30009740B-page 14 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Register 5-2: LCDREG: LCD Voltage Regulator Control Register R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 CPEN — — — — — — — bit 15 bit 8 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-0 R/W-0 — — BIAS2 BIAS1 BIAS0 MODE13 CKSEL1 CKSEL 0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared bit 15 CPEN: LCD Charge Pump Enable bit 1 = Charge pump enabled; highest LCD Bias voltage is 3.6V 0 = Charge pump disabled; highest LCD Bias voltage is AVDD bit 14-6 Unimplemented: Read as ‘0’ bit 5-3 BIAS<2:0>: Regulator Voltage Output Control bits 111 = 3.60V peak (offset on LCDBIAS0 of 0V) 110 = 3.47V peak (offset on LCDBIAS0 of 0.13V) 101 = 3.34V peak (offset on LCDBIAS0 of 0.26V) 100 = 3.21V peak (offset on LCDBIAS0 of 0.39V) 011 = 3.08V peak (offset on LCDBIAS0 of 0.52V) 010 = 2.95V peak (offset on LCDBIAS0 of 0.65V) 001 = 2.82V peak (offset on LCDBIAS0 of 0.78V) 000 = 2.69V peak (offset on LCDBIAS0 of 0.91V) bit 2 MODE13: 1/3 LCD Bias Enable bit 1 = Regulator output supports 1/3 LCD Bias mode 0 = Regulator output supports Static LCD Bias mode bit 1-0 CKSEL<1:0>: Regulator Clock Source Select bits 11 = 31 kHz LPRC 10 = 8 MHz FRC 01 = SOSC 00 = LCD regulator is disabled 2010-2013 Microchip Technology Inc. x = Bit is unknown DS30009740B-page 15 dsPIC33/PIC24 Family Reference Manual 5.3 Bias Configurations dsPIC33/PIC24 family devices have four distinct circuit configurations for LCD Bias generation: • • • • M0: Regulator with Boost M1: Regulator without Boost M2: Resistor Ladder with Software Contrast M3: Resistor Ladder with Hardware Contrast 5.3.1 M0 (REGULATOR WITH BOOST) In M0 operation, the LCD charge pump feature is enabled. This allows the regulator to generate voltages up to +3.6V to the LCD (as measured at LCDBIAS3). M0 uses a Flyback Capacitor connected between VLCAP1 and VLCAP2, as well as filter capacitors on LCDBIAS0 through LCDBIAS3, to obtain the required voltage boost (Figure 5-4). The output voltage (VBIAS) is the difference of the potential between LCDBIAS3 and LCDBIAS0. It is set by the BIAS<2:0> bits, which adjust the offset between LCDBIAS0 and VSS. The Flyback Capacitor (CFLY) acts as a charge storage element for large LCD loads. This mode is useful in those cases where the voltage requirements of the LCD are higher than the microcontroller’s VDD. It also permits software control of the display’s contrast, by adjustment of the Bias voltage, by changing the value of the BIASx bits. M0 supports Static and 1/3 Bias types. Generation of the voltage levels for 1/3 Bias is handled automatically, but must be configured in software. M0 is enabled by selecting a valid regulator clock source (CKSEL<1:0> set to any value except ‘00’) and setting the CPEN bit. If a Static Bias type is required, the MODE13 bit must be cleared. 5.3.2 M1 (REGULATOR WITHOUT BOOST) M1 operation is similar to M0, but does not use the LCD charge pump. It can provide VBIAS up to the voltage level supplied directly to LCDBIAS3. It can be used in cases where VDD for the application is expected to never drop below a level that can provide adequate contrast for the LCD. The connection of external components is very similar to M0, except that LCDBIAS3 must be tied directly to VDD (Figure 5-4). Note: When the device is put to Sleep while operating in M0 or M1 mode, make sure that the Bias capacitors are fully discharged to get the lowest Sleep current. • The BIAS<2:0> bits can still be used to adjust contrast in software by changing VBIAS. As with M0, changing these bits changes the offset between LCDBIAS0 and VSS. In M1, this is reflected in the change between the LCDBIAS0 and the voltage tied to LCDBIAS3. Thus, if VDD should change, VBIAS will also change; where in M0, the level of VBIAS is constant. • Like M0, M1 supports Static and 1/3 Bias types. Generation of the voltage levels for 1/3 Bias is handled automatically, but must be configured in software. M1 is enabled by selecting a valid regulator clock source (CKSEL<1:0> set to any value except ‘00’) and clearing the CPEN bit. If 1/3 Bias type is required, the MODE13 bit should also be set. DS30009740B-page 16 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Figure 5-4: LCD Regulator Connections for M0 and M1 Configurations dsPIC33/PIC24 VDD VDD AVDD VLCAP1 CFLY 0.47 F(1) CFLY 0.47 F(1) VLCAP2 LCDBIAS3 C3 0.47 F(1) LCDBIAS2 C2 0.47 F(1) LCDBIAS1 C1 0.47 F(1) LCDBIAS0 C0 0.47 F(1) Mode 0 (VBIAS up to 3.6V) Note 1: VDD C2 0.47 F(1) C1 0.47 F(1) C0 0.47 F(1) Mode 1 (VBIAS VDD) These values are provided for design guidance only. They should be optimized for the application by the designer based on the actual LCD specifications. 2010-2013 Microchip Technology Inc. DS30009740B-page 17 dsPIC33/PIC24 Family Reference Manual 5.3.3 M2 (RESISTOR LADDER WITH SOFTWARE CONTRAST) M2 operation also uses the LCD regulator but disables the charge pump. The regulator’s internal voltage reference remains active as a way to regulate contrast. It is used in cases where the current requirements of the LCD exceed the capacity of the regulator’s charge pump. In this configuration, the LCD Bias voltage levels are created by an external resistor voltage divider, connected across LCDBIAS0 through LCDBIAS3, with the top of the divider tied to VDD (Figure 5-5). The potential at the bottom of the ladder is determined by the LCD regulator’s voltage reference, tied internally to LCDBIAS0. The Bias type is determined by the voltages on the LCDBIAS pins, which are controlled by the configuration of the resistor ladder. Most applications using M2 will use a 1/3 or 1/2 Bias type. While Static Bias can also be used, it offers extremely limited contrast range and additional current consumption over other Bias Generation modes. Like M1, the LCDBIAS bits can be used to control contrast, limited by the level of VDD supplied to the device. Also, since there is no capacitor required across VLCAP1 and VLCAP2, these pins are available as digital I/O ports: RG2 and RG3. M2 is selected by clearing the CKSEL<1:0> bits and setting the CPEN bit. Figure 5-5: Resistor Ladder Connections for M2 Configuration dsPIC33/PIC24 VDD AVDD LCDBIAS3 10 k(1) 10 k(1) LCDBIAS2 10 k(1) LCDBIAS1 10 k(1) 10 k(1) LCDBIAS0 1/2 Bias 1/3 Bias Bias Type Bias Level at Pin 1/2 Bias 1/3 Bias LCDBIAS0 (Internal Low Reference Voltage) (Internal Low Reference Voltage) LCDBIAS1 1/2 VBIAS 1/3 VBIAS LCDBIAS2 1/2 VBIAS 2/3 VBIAS LCDBIAS3 VBIAS (up to AVDD) VBIAS (up to AVDD) Note 1: These values are provided for design guidance only. They should be optimized for the application by the designer based on the actual LCD specifications. DS30009740B-page 18 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) 5.3.4 M3 (RESISTOR LADDER WITH HARDWARE CONTRAST) In M3, the LCD regulator is completely disabled. Like M2, LCD Bias levels are tied to AVDD and are generated using an external divider. The difference is that the internal voltage reference is also disabled and the bottom of the ladder is tied to ground (VSS) (see Figure 5-6). The value of the resistors, and the difference between VSS and VDD, determine the contrast range; no software adjustment is possible. This configuration is also used where the LCD module’s current requirements exceed the capacity of the charge pump and software contrast control is not needed. Depending on the Bias type required, resistors are connected between some or all of the pins. A potentiometer can also be connected between LCDBIAS3 and VDD to allow for hardware controlled contrast adjustment. M3 is selected by clearing the CKSEL<1:0> and CPEN bits. Figure 5-6: Resistor Ladder Connections for M3 Configuration dsPIC33/PIC24 VDD AVDD (2) LCDBIAS3 10 k(1) 10 k(1) LCDBIAS2 10 k(1) LCDBIAS1 10 k(1) 10 k(1) LCDBIAS0 Static Bias 1/2 Bias 1/3 Bias Bias Type Bias Level at Pin Static 1/2 Bias 1/3 Bias LCDBIAS0 AVSS AVSS AVSS LCDBIAS1 AVSS 1/2 AVDD 1/3 AVDD LCDBIAS2 AVDD 1/2 AVDD 2/3 AVDD LCDBIAS3 AVDD AVDD AVDD Note 1: 2: These values are provided for design guidance only. They should be optimized for the application by the designer based on the actual LCD specifications. A potentiometer for manual contrast adjustment is optional; it may be omitted entirely. 2010-2013 Microchip Technology Inc. DS30009740B-page 19 dsPIC33/PIC24 Family Reference Manual 5.4 Design Considerations for the LCD Charge Pump When designing applications that use the LCD regulator with the charge pump enabled, users must always consider both the dynamic current and RMS (Static) current requirements of the display, and what the charge pump can deliver. Both dynamic and Static current can be determined by Equation 5-1: Equation 5-1: I=Cx dV dT For dynamic current, C is the value of the capacitors attached to LCDBIAS3 and LCDBIAS2. The variable, dV, is the voltage drop allowed on C2 and C3 during a voltage switch on the LCD display, and dT is the duration of the transient current after a clock pulse occurs. For practical design purposes, these will be assumed to be 0.047 ìF for C, 0.1V for dV and 1 ìs for dT. This yields a dynamic current of 4.7 mA for 1 ìs. RMS (Root Mean Square) current is determined by the value of CFLY for C, the voltage across VLCAP1 and VLCAP2 for dV, and the regulator clock period (TPER) for dT. Assuming a CFLY value of 0.047 ìF, a value of 1.02V across CFLY and a TPER of 30, the maximum theoretical Static current will be 1.8 mA. Since the charge pump must charge five capacitors, the maximum current becomes 360 ìA. For a real world assumption of 50% efficiency, this yields a practical current of 180 ìA. Users should compare the calculated current capacity against the requirements of the LCD. While dV and dT are relatively fixed by device design, the values of CFLY and the capacitors on the LCDBIAS pins can be changed to increase or decrease current. As always, any changes should be evaluated in the actual circuit for their impact on the application. DS30009740B-page 20 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) 6.0 LCD MULTIPLEX TYPES The LCD driver module can be configured into four Multiplex types: • • • • • • • • Static (only COM0 used) 1/2 Multiplex (COM0 and COM1 are used) 1/3 Multiplex (COM0, COM1 and COM2 are used) 1/4 Multiplex (COM0, COM1, COM2 and COM3 are used) 1/5 Multiplex (COM0, COM1, COM2, COM3 and COM4 are used) 1/6 Multiplex (COM0, COM1, COM2, COM3, COM4 and COM5 are used) 1/7 Multiplex (COM0, COM1, COM2, COM3, COM4, COM5 and COM6 are used) 1/8 Multiplex (COM0, COM1, COM2, COM3, COM4, COM5, COM6 and COM7 are used) The LMUX<2:0> bits setting (LCDCON<2:0>) decides the function of the COM pins. (For details, see Table 6-1.) If the pin is a digital I/O, the corresponding TRIS bit controls the data direction. If the pin is a COM drive, the TRIS setting of that pin is overridden. Note: Table 6-1: On a Power-on Reset, the LMUX<2:0> bits are ‘000’. COM<7:0> Pin Function LMUX<2:0> COM7 Pin COM6 Pin COM5 Pin COM4 Pin COM3 Pin COM2 Pin COM1 Pin COM0 Pin 111 COM7 COM6 COM5 COM4 COM3 COM2 COM1 COM0 110 I/O Pin COM6 COM5 COM4 COM3 COM2 COM1 COM0 101 I/O Pin I/O Pin COM5 COM4 COM3 COM2 COM1 COM0 100 I/O Pin I/O Pin I/O Pin COM4 COM3 COM2 COM1 COM0 011 I/O Pin I/O Pin I/O Pin I/O Pin COM3 COM2 COM1 COM0 010 I/O Pin I/O Pin I/O Pin I/O Pin I/O Pin COM2 COM1 COM0 001 I/O Pin I/O Pin I/O Pin I/O Pin I/O Pin I/O Pin COM1 COM0 000 I/O Pin I/O Pin I/O Pin I/O Pin I/O Pin I/O Pin I/O Pin COM0 Note: Pins, COM<7:4>, can also be used as SEG pins when 1/4 Multiplex to Static Multiplex are used. These pins can be used as I/O pins only if the respective bits in the LCDSEx registers are set to ‘0’. 2010-2013 Microchip Technology Inc. DS30009740B-page 21 dsPIC33/PIC24 Family Reference Manual 7.0 SEGMENT ENABLES The LCDSEx registers are used to select the pin function for each segment pin. The selection allows each pin to operate as either an LCD segment driver or a digital only pin. To configure the pin as a segment driver, the corresponding bits in the LCDSEx registers must be set to ‘1’. If the pin is a digital I/O, the corresponding TRIS bit controls the data direction. Any bit set in the LCDSEx registers overrides any bit settings in the corresponding TRIS register. On a Power-on Reset, these pins are configured as digital I/O. Note: 8.0 PIXEL CONTROL The LCDDATAx registers contain bits that define the state of each pixel. Each bit defines one unique pixel. Table 3-2 shows the correlation of each bit in the LCDDATAx registers to the respective common and segment signals. Any LCD pixel location not being used for display can be used as general purpose RAM. 9.0 LCD FRAME FREQUENCY The rate at which the COM and SEG outputs change is called the LCD frame frequency. Table 9-1: Note: 10.0 Frame Frequency Formulas Multiplex Frame Frequency = Static (000) Clock Source/(4 x 1 x (LP<3:0> + 1)) 1/2 (001) Clock Source/(2 x 2 x (LP<3:0> + 1)) 1/3 (010) Clock Source/(1 x 3 x (LP<3:0> + 1)) 1/4 (011) Clock Source/(1 x 4 x (LP<3:0> + 1)) 1/5 (100) Clock Source/(1 x 5 x (LP<3:0> + 1)) 1/6 (101) Clock Source/(1 x 6 x (LP<3:0> + 1)) 1/7 (110) Clock Source/(1 x 7 x (LP<3:0> + 1)) 1/8 (111) Clock Source/(1 x 8 x (LP<3:0> + 1)) The clock source is FRC/8192, SOSC/32 or LPRC/32. LCD WAVEFORM GENERATION LCD waveform generation is based on the philosophy that the net AC voltage across the dark pixel should be maximized and the net AC voltage across the clear pixel should be minimized. The net DC voltage across any pixel should be zero. The COM signal represents the time slice for each common, while the SEG contains the pixel data. The pixel signal (COM-SEG) will have no DC component and can take only one of the two RMS values. The higher RMS value will create a dark pixel and a lower RMS value will create a clear pixel. As the number of commons increases, the delta between the two RMS values decreases. The delta represents the maximum contrast that the display can have. The LCDs can be driven by two types of waveforms: Type-A and Type-B. In a Type-A waveform, the phase changes within each common type, whereas a Type-B waveform’s phase changes on each frame boundary. Thus, Type-A waveforms maintain 0 VDC over a single frame, whereas Type-B waveforms take two frames. Note: DS30009740B-page 22 If Sleep has to be executed with LCD Sleep enabled (SLPEN (LCDCON<6>) = 1), care must be taken to execute Sleep only when the VDC on all the pixels is ‘0’. 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Figure 10-1 through Figure 10-13 provide waveforms for Static, Half-Multiplex, One-Third Multiplex and Quarter Multiplex drives for Type-A and Type-B waveforms. Figure 10-1: Type-A/Type-B Waveforms in Static Drive V1 COM0 V0 COM0 V1 SEG0 V0 V1 SEG1 SEG0 SEG2 SEG7 SEG6 SEG5 SEG4 SEG3 SEG1 V0 V1 V0 COM0-SEG0 -V1 COM0-SEG1 V0 1 Frame 2010-2013 Microchip Technology Inc. DS30009740B-page 23 dsPIC33/PIC24 Family Reference Manual Figure 10-2: Type-A Waveforms in 1/2 MUX, 1/2 Bias Drive V2 V1 COM0 V0 COM1 V2 COM0 COM1 V1 V0 V2 V1 SEG0 V0 SEG0 SEG1 SEG2 SEG3 V2 V1 SEG1 V0 V2 V1 V0 COM0-SEG0 -V1 -V2 V2 V1 V0 COM0-SEG1 -V1 -V2 1 Frame DS30009740B-page 24 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Figure 10-3: Type-B Waveforms in 1/2 MUX, 1/2 Bias Drive V2 V1 COM0 COM1 V0 COM0 V2 V1 COM1 V0 V2 SEG0 V1 V0 SEG0 SEG1 SEG2 SEG3 V2 SEG1 V1 V0 V2 V1 V0 COM0-SEG0 -V1 -V2 V2 V1 V0 COM0-SEG1 -V1 -V2 2 Frames 2010-2013 Microchip Technology Inc. DS30009740B-page 25 dsPIC33/PIC24 Family Reference Manual Figure 10-4: Type-A Waveforms in 1/2 MUX, 1/3 Bias Drive V3 V2 COM0 V1 COM1 V0 V3 COM0 V2 COM1 V1 V0 V3 V2 SEG0 V1 V0 SEG0 SEG1 SEG2 SEG3 V3 V2 SEG1 V1 V0 V3 V2 V1 V0 COM0-SEG0 -V1 -V2 -V3 V3 V2 V1 V0 COM0-SEG1 -V1 -V2 1 Frame DS30009740B-page 26 -V3 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Figure 10-5: Type-B Waveforms in 1/2 MUX, 1/3 Bias Drive V3 V2 COM0 V1 COM1 V0 V3 COM0 V2 COM1 V1 V0 V3 V2 SEG0 V1 V0 V2 SEG1 SEG0 SEG1 SEG2 SEG3 V3 V1 V0 V3 V2 V1 V0 COM0-SEG0 -V1 -V2 -V3 V3 V2 V1 V0 COM0-SEG1 -V1 -V2 2 Frames 2010-2013 Microchip Technology Inc. -V3 DS30009740B-page 27 dsPIC33/PIC24 Family Reference Manual Figure 10-6: Type-A Waveforms in 1/3 MUX, 1/2 Bias Drive V2 COM0 V1 V0 COM2 V2 COM1 V1 V0 COM1 COM0 V2 COM2 V1 V0 V2 SEG0 SEG2 V1 SEG0 SEG1 SEG2 V0 V2 V1 SEG1 V0 V2 V1 V0 COM0-SEG0 -V1 -V2 V2 V1 V0 COM0-SEG1 -V1 -V2 1 Frame DS30009740B-page 28 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Figure 10-7: Type-B Waveforms in 1/3 MUX, 1/2 Bias Drive V2 COM0 V1 V0 COM2 V2 COM1 V1 COM1 V0 COM0 V2 COM2 V1 V0 V2 V1 V0 SEG0 SEG1 SEG2 SEG0 V2 SEG1 V1 V0 V2 V1 V0 COM0-SEG0 -V1 -V2 V2 V1 V0 COM0-SEG1 -V1 -V2 2 Frames 2010-2013 Microchip Technology Inc. DS30009740B-page 29 dsPIC33/PIC24 Family Reference Manual Figure 10-8: Type-A Waveforms in 1/3 MUX, 1/3 Bias Drive V3 V2 COM0 V1 V0 V3 COM2 V2 COM1 V1 COM1 V0 COM0 V3 V2 COM2 V1 V0 V3 V2 V1 V0 SEG0 SEG1 SEG2 SEG0 SEG2 V3 V2 SEG1 V1 V0 V3 V2 V1 V0 COM0-SEG0 -V1 -V2 -V3 V3 V2 V1 V0 COM0-SEG1 -V1 -V2 -V3 1 Frame DS30009740B-page 30 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Figure 10-9: Type-B Waveforms in 1/3 MUX, 1/3 Bias Drive V3 V2 COM0 V1 V0 V3 COM2 V2 COM1 V1 COM1 V0 COM0 V3 V2 COM2 V1 V0 V3 V2 V1 V0 SEG0 SEG1 SEG2 SEG0 V3 V2 SEG1 V1 V0 V3 V2 V1 V0 COM0-SEG0 -V1 -V2 -V3 V3 V2 V1 V0 COM0-SEG1 -V1 -V2 -V3 2 Frames 2010-2013 Microchip Technology Inc. DS30009740B-page 31 dsPIC33/PIC24 Family Reference Manual Figure 10-10: Type-A Waveforms in 1/4 MUX, 1/3 Bias Drive COM3 COM2 COM1 COM0 V3 V2 V1 V0 COM1 V3 V2 V1 V0 COM2 V3 V2 V1 V0 COM3 V3 V2 V1 V0 SEG0 V3 V2 V1 V0 SEG1 V3 V2 V1 V0 SEG0 SEG1 COM0 COM0-SEG0 V3 V2 V1 V0 -V1 -V2 -V3 COM0-SEG1 V3 V2 V1 V0 -V1 -V2 -V3 1 Frame DS30009740B-page 32 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Figure 10-11: Type-B Waveforms in 1/4 MUX, 1/3 Bias Drive COM3 COM2 COM1 COM0 V3 V2 V1 V0 COM1 V3 V2 V1 V0 COM2 V3 V2 V1 V0 COM3 V3 V2 V1 V0 SEG0 V3 V2 V1 V0 SEG1 V3 V2 V1 V0 SEG0 SEG1 COM0 COM0-SEG0 V3 V2 V1 V0 -V1 -V2 -V3 COM0-SEG1 V3 V2 V1 V0 -V1 -V2 -V3 2 Frames 2010-2013 Microchip Technology Inc. DS30009740B-page 33 dsPIC33/PIC24 Family Reference Manual Figure 10-12: Type-A Waveforms in 1/8 MUX, 1/3 Bias Drive COM4 COM0 COM5 COM3 COM7 COM6 COM2 COM1 COM1 COM0 COM2 COM7 SEG0 SEG0 COM0-SEG0 COM1-SEG0 DS30009740B-page 34 V3 V2 V1 V0 V3 V2 V1 V0 V3 V2 V1 V0 V3 V2 V1 V0 V3 V2 V1 V0 V3 V2 V1 V0 -V1 -V2 -V3 V3 V2 V1 V0 -V1 -V2 -V3 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Figure 10-13: Type-B Waveforms in 1/8 MUX, 1/3 Bias Drive COM4 COM0 COM5 COM3 COM7 COM1 V3 V2 V1 V0 COM2 V3 V2 V1 V0 COM6 COM2 COM1 COM0 COM7 SEG0 SEG0 COM0 - SEG0 COM1 - SEG0 2010-2013 Microchip Technology Inc. V3 V2 V1 V0 V3 V2 V1 V0 V3 V2 V1 V0 V3 V2 V1 V0 -V1 -V2 -V3 V3 V2 V1 V0 -V1 -V2 -V3 DS30009740B-page 35 dsPIC33/PIC24 Family Reference Manual 11.0 LCD INTERRUPTS The LCD timing generation provides an interrupt that defines the LCD frame timing. This interrupt can be used to coordinate the writing of the pixel data with the start of a new frame, which produces a visually crisp transition of the image. This interrupt can also be used to synchronize external events to the LCD. For example, the interface to an external segment driver can be synchronized for segment data updates to the LCD frame. A new frame is defined as beginning at the leading edge of the COM0 common signal. The interrupt will be set immediately after the LCD controller completes accessing all pixel data required for a frame. This will occur at a fixed interval before the frame boundary (TFINT), as shown in Figure 11-1. The LCD controller will begin to access data for the next frame, within the interval from the interrupt to when the controller begins accessing data after the interrupt (TFWR). New data must be written within TFWR, as this is when the LCD controller will begin to access the data for the next frame. When the LCD driver is running with Type-B waveforms and the LMUX<2:0> bits are not equal to ‘00’, there are some additional issues. Since the DC voltage on the pixel takes two frames to maintain 0V, the pixel data must not change between subsequent frames. If the pixel data was allowed to change, the waveform for the odd frames would not necessarily be the complement of the waveform generated in the even frames, and a DC component would be introduced into the panel. Because of this, using Type-B waveforms requires synchronizing the LCD pixel updates to occur within a subframe after the frame interrupt. To correctly sequence writing in Type-B, the interrupt only occurs on complete phase intervals. If the user attempts to write when the write is disabled, the WERR bit (LCDCON<5>) is set. Note: DS30009740B-page 36 The interrupt is not generated when the Type-A waveform is selected and when the Type-B with no Multiplex (Static) is selected. 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) Figure 11-1: Example Waveforms and Interrupt Timing in Quarter Duty Cycle Drive LCD Interrupt Occurs Controller Accesses Next Frame Data COM0 V3 V2 V1 V0 COM1 V3 V2 V1 V0 COM2 V3 V2 V1 V0 V3 V2 V1 V0 COM3 2 Frames TFINT Frame Boundary Frame Boundary TFWR Frame Boundary TFWR = TFRAME/2 * (LMUX<2:0> + 1) + TCY/2 TFINT = (TFWR/2 – (2 TCY + 40 ns)) Minimum = 1.5(TFRAME/4) – (2 TCY + 40 ns) (TFWR/2 – (1 TCY + 40 ns)) Maximum = 1.5(TFRAME/4) – (1 TCY + 40 ns) 2010-2013 Microchip Technology Inc. DS30009740B-page 37 dsPIC33/PIC24 Family Reference Manual 12.0 CONFIGURING THE LCD MODULE To configure the LCD module: 1. 2. 3. 4. 5. 6. 7. DS30009740B-page 38 Select the frame clock prescale using bits, LP<2:0> (LCDPS<2:0>). Configure the appropriate pins to function as segment drivers using the LCDSEx registers. If using the internal reference resistors for biasing, enable the internal reference ladder and: • Define the Mode A and Mode B interval by using the LRLAT<2:0> bits (LCDREF<2:0>) • Define the low, medium or high ladder for Mode A and Mode B by using the LRLAP<1:0> bits (LCDREF<7:6>) and the LRLBP<1:0> bits (LCDREF<5:4>), respectively • Set the VLCDxPE bits (LCDREF<10:8> and enable the LCDIRE bit (LCDREF<15>) Configure the following LCD module functions using the LCDCON register: • Multiplex and Bias mode – LMUX<2:0> bits • Timing Source – CS<1:0> bits • Sleep mode – SLPEN bit Write the initial values to the LCD Pixel Data registers: LCDDATA0 through LCDDATA31. Clear the LCD Interrupt Flag, LCDIF, and if desired, enable the interrupt by setting bit, LCDIE. Enable the LCD module by setting bit, LCDEN (LCDCON<15>). 2010-2013 Microchip Technology Inc. Liquid Crystal Display (LCD) 13.0 OPERATION DURING SLEEP The LCD module can operate during Sleep. The selection is controlled by the SLPEN bit (LCDCON<6>). Setting the SLPEN bit allows the LCD module to go to Sleep. Clearing the SLPEN bit allows the module to continue to operate during Sleep. If a SLEEP instruction is executed and SLPEN = 1, the LCD module will cease all functions and go into a very Low-Current Consumption mode. The module will stop operation immediately and drive the minimum LCD voltage on both segment and common lines. Figure 13-1 shows this operation. The LCD module current consumption will not decrease in this mode, but the overall consumption of the device will be lower due to the shutdown of the core and other peripheral functions. To ensure that no DC component is introduced on the panel, the SLEEP instruction should be executed immediately after a LCD frame boundary. The LCD interrupt can be used to determine the frame boundary. See Section 11.0 “LCD Interrupts” for the formulas to calculate the delay. If a SLEEP instruction is executed and SLPEN = 0, the module will continue to display the current contents of the LCDDATAx registers. The LCD data cannot be changed. Figure 13-1: Sleep Entry/Exit when SLPEN = 1 or CS<1:0> = 00 V3 V2 V1 COM0 V0 V3 V2 V1 COM1 V0 V3 V2 V1 COM2 V0 V3 V2 V1 SEG0 V0 2 Frames SLEEP Instruction Execution 2010-2013 Microchip Technology Inc. Wake-up DS30009740B-page 39 REGISTERS Table 14-1: Name Special Function Registers Associated with LCD Driver Module Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 LCDEN — LCDSIDL — — — — — — — — — — — — — LCDREF LCDIRE — LCDREG CPEN — LCDCON LCDPS Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 — SLPEN WERR CS1 CS0 LMUX2 LMUX1 LMUX0 WFT BIASMD LCDA WA LP3 LP2 LP1 LP0 — LRLAT2 LRLAT1 LRLAT0 LCDCST2 LCDCST1 LCDCST0 VLCD3PE VLCD2PE VLCD1PE LRLAP1 LRLAP0 LRLBP1 LRLBP0 — — — — LCDSEx — — — — BIAS2 BIAS1 BIAS0 MODE13 CKSEL1 CKSEL0 LCD Segment x Pin Enable Registers LCDDATAx LCD Data x Registers IFS6 — — — — — — — — — — — LCDIF — IEC6 — — — — — — — — — — — LCDIE — — — — IPC25 — — — — — — — — — — — — — LCDIP2 LCDIP1 LCDIP0 Legend: — = Unimplemented bit; r = Reserved bit — — — 2010-2013 Microchip Technology Inc. dsPIC33/PIC24 Family Reference Manual DS30009740B-page 40 14.0 Liquid Crystal Display (LCD) 15.0 REVISION HISTORY Revision A (December 2010) This is the initial released revision of this document. Revision B (October 2013) Corrected CS<1:0> bit information in Register 2-1. Removed MUX from Figure 5-3. Minor typographical edits throughout document. 2010-2013 Microchip Technology Inc. DS30009740B-page 41 dsPIC33/PIC24 Family Reference Manual NOTES: DS30009740B-page 42 2010-2013 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MTP, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. Analog-for-the-Digital Age, Application Maestro, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 2010-2013, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-62077-536-3 QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV == ISO/TS 16949 == 2010-2013 Microchip Technology Inc. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. DS30009740B-page 43 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 China - Hong Kong SAR Tel: 852-2943-5100 Fax: 852-2401-3431 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 China - Shenzhen Tel: 86-755-8864-2200 Fax: 86-755-8203-1760 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 India - Pune Tel: 91-20-3019-1500 Japan - Osaka Tel: 81-6-6152-7160 Fax: 81-6-6152-9310 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Japan - Tokyo Tel: 81-3-6880- 3770 Fax: 81-3-6880-3771 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 Taiwan - Kaohsiung Tel: 886-7-213-7828 Fax: 886-7-330-9305 Taiwan - Taipei Tel: 886-2-2508-8600 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS30009740B-page 44 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 08/20/13 2010-2013 Microchip Technology Inc.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res Author : Microchip Technology Create Date : 2013:10:16 15:18:59Z Keywords : dsPIC33;, PIC24;, Liquid, Crystal, Display;, LCD Modify Date : 2013:10:16 15:33:26-07:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Producer : Acrobat Distiller 10.1.8 (Windows) Creator Tool : FrameMaker 11.0.2 Metadata Date : 2013:10:16 15:33:26-07:00 Format : application/pdf Title : dsPIC33/PIC24 Family Reference Manual, Liquid Crystal Display (LCD) Creator : Microchip Technology Description : FRM Subject : dsPIC33, PIC24, Liquid Crystal Display, LCD Document ID : uuid:f7d06017-6c5b-499c-b79c-223087fc47d6 Instance ID : uuid:efe4a6f7-438a-4bb5-9692-420a8890da7d Page Mode : UseOutlines Page Count : 44EXIF Metadata provided by EXIF.tools