S COM 7K Owner's Manual Manual7k203i

• Title Page
• Table of Contents
• Product Description
  • Standard Hardware Features
    • Configuration
    • Cabinet
    • Main Board
  • Optional Hardware Features
    • Telephone Interface Module
    • Speech Synthesis Module
    • Digital Audio Delay Module
  • Standard Software Features
    • CW Identifier
    • CW Messages and Paging Formats
    • Timers
    • Repeater Characteristics
    • Clock and Calendar
    • Logic Inputs and Outputs
    • Command Language
• Getting Started
  • Power ON Initialization
    • Initialize Controller
    • Cold Start
    • Warm Start
    • Default Condition
• Programming Fundamentals
  • Valid Digit and Time Detection
  • Control Command Structure
  • Command Response Messages
    • Acknowledgement
    • Errors
  • Special Keys
    • Star(*) and Carrier Drop as Terminators
    • Pound (#) as Clear or Abort Key
  • DTMF Interdigit Timer
  • DTMF Mute Delay
• Messages
  • Message Buffer
  • Message Handler
  • Control Characters
  • Routing and Unrouting Control Characters
  • Synchronizing Messages and Commands
  • CW Messages
    • Control Character
    • Format
    • Pre-Message Delay Character
    • Wordspace Character
    • Frequency Change
    • Speed Change
    • CW Alphanumeric Characters
    • CW Punctuation and Related Characters
    • CW Frequency Change Characters
    • CW Speed Change Characters
  • Beep Messages
    • Control Character
    • Format
    • Beep Parameters (General)
    • Pre-Message Delay Character
    • Factory-Fixed-Frequency Beeps
    • Owner-Fixed Frequency Beeps
    • Custom Beeps
    • Custom Beep Delay
    • Beep Gap Change Characters
    • Beep Duration Change Characters
    • Automatic Beep Gap ON Character
    • Automatic Beep Gap OFF Character
    • Defaults
  • Single Tone Page Messages
    • Control Character
    • Format
    • Delays
  • Two-Tone Sequential Page Messages
    • Control Character
    • Format
    • Delays
  • Five-Six-Tone Page Messages
    • Control Character
    • Format
    • Delays
  • DTMF Page Messages
    • Control Character
    • Format
    • Delays
    • Defaults
    • DTMF Characters
    • DTMF Duration Change Characters
    • DTMF Custom Duration Change Characters
    • DTMF Gap Change Characters
    • DTMF Custom Gap Change Characters
    • DTMF Pause Characters
    • DTMF Custom Pause Characters
    • DTMF Custom Changes (Duration, Gap, Pause)
    • DTMF-Related Notes
    • DTMF Character Set Tables Explained
  • Synthesized Speech Messages
    • Control Character
    • Format
    • Delay Character
    • Pause Character
    • Timeout Timer
    • Synthesized Speech Vocabulary
  • Tone Codes
    • Tone Code Table Explained
    • Calculating Tone Codes
  • Run-Time Variables
  • Commands
    • Enable/Disable CW
    • Select Frequency of CW
    • Send Next Message Slowly
    • Select CW Speed
    • Select Frequency of Owner-Fixed Frequency Beeps
    • Select Programmable Messages
    • Review Programmable Messages
    • Select/Review/Play User Messages
    • Send Message
    • Select (Review) Command Response Messages
    • Select (Review) Programmable Messages
• Security
  • Commands
    • Assign Control Operator Password
    • Assign Master Password
    • Assign Control Operator Privilege Level
    • Assign Control Operator Privilege Level to a Range
    • Enable/Disable Front Panel Display
• Macros
  • Quantity of Macros
  • Size of Macros
  • Names of Macros
  • Contents of Macros
  • Sequence of Execution
  • Cautions
  • Applications of Macros
  • Commands
    • Create New Macro
    • Append To Macro
    • List Macro
    • Erase Macro
    • Erase All Macros
    • Rename Macro
    • Pause
    • Select Power ON_Triggered Macro
• Telephone Interface Functions
  • Autopatch
    • Autopatch Setup and Configuration
    • Autopatch Dialing Mode
    • Autopatch Timeout Timer
    • Autopatch Access and Passwords
    • Autopatch Call Types
    • Autopatch Restrictions
    • Autopatch Redialer
    • Autopatch Call Counter
  • Phone Line Control Mode
    • Phone Line Busy Input
    • Phone Line Busy Output
    • Phone Line Answer Modes
  • Reverse Patch
  • Multiple Port Access
    • Autopatch Audio Routing
    • Autopatch Command Response Message Routing
    • Receiver-Specific Autopatch Access
    • Preventing Multiple Access
  • Commands
    • Select Autopatch Dialing Mode
    • Select (Review) Autopatch Dialing Message
    • Select (Review) Autopatch Error Messages
    • Select (Review) Autopatch Dump Message
    • Enable/Disable Autopatch Dialing Mixed-Mode
    • Select Pause ("B") Digit Time
    • Enable/Disable Pound Down (# Dump)
    • Select Dialing Prefix
    • Dump Autopatch Using a Code
    • Select Autopatch Access-Triggered Macro
    • Select Autopatch Dump-Triggered Macro
    • Enable/Disable Full-Duplex Mode
    • Enable/Disable Autopatch Privacy
    • Enable/Disable Repeater-to-Phone DTMF Mute
    • Enable/Disable ID Messages During Autopatch
    • Require Dump Before Next Call
    • Select Receiver-to-Autopatch-Triggered Macros
    • Landline Hookflash
    • Select Autopatch Timeout Timer
    • Reset Autopatch Timeout Timer
    • Select (Review) Autopatch Timeout Warning Message
    • Access Autopatch (With Password)
    • Access Autopatch (Without Password)
    • Change Autopatch Access Password
    • Enable/Disable Autopatch Access Without Password
    • Go Off-Hook
    • Select Autopatch Call Types
    • Clear (or Enter) Accepted Number Table
    • Clear (or Enter) Rejected Number Table
    • Redial Last Number
    • Clear Autopatch Redialer
    • Clear Autopatch Call Counter
    • Send Autopatch Call Count
    • Select Phone Line Answer Mode
    • Select (Review) Phone Line Answer Message
    • Select Phone Line Answer Macro
    • Select Control Mode Dump-Triggered Macro
    • Select Phone Line Off-Hook Timer
    • Monitor/Talk Out Via Phone
    • Trigger Reverse Patch
    • Answer Reverse Patch
    • Select (Review) Reverse Patch Ringout Message
    • Select Reverse Patch Ring-Triggered Macro
    • Select Autopatch Receiver-Specific Access-Triggered Macro
    • Select Autopatch Command Response Message Routing
• Clock and Calendar
  • Commands
    • Set Clock and Calendar
    • Adjust Daylight Savings Time
    • Reset Clock Seconds
    • Adjust Clock Seconds
• Scheduler
  • Commands
    • Create a Setpoint
    • Delete One or More Setpoints
    • Enable/Disable Scheduler
• CTCSS Functions
  • Commands
    • Enable/Disable CTCSS Encoder
    • Select Frequency of CTCSS
• DTMF Decoder
  • Commands
    • Enable/Disable Command Response Messages
    • Select DTMF Priority/Scan
    • Select DTMF Decoder Access Mode
    • Select DTMF Decoder Interdigit Timer
    • Select DTMF Decoder Mute Delay
    • Enable/Disable DTMF Decoder Mute
    • Enable/Disable DTMF Long Tones
    • Select DTMF Long Tone Macros
    • Select DTMF Digit-Decoded Macros
• Identifier
  • Commands
    • Select (Review) Identifier Messages
    • Select ID-Triggered Macros
    • Select ID Message Interval
    • Select ID Pending Interval for Tx1 and Tx2
    • Reset Initial ID Message to Normal Message
    • Send Initial ID Message
    • Select (Review) Programmable Tail Messages for Tx1
    • Select (Review) Initial and Normal ID Tail Messages
    • Enable/Disable ID Messages During Autopatch
• Links
  • Commands
    • Enable/Disable Path
    • Select Audio Routing Priority
    • Select Path Access Mode
• Logic Inputs
  • Commands
    • Assign Macro to Logic Input
• Logic Outputs
  • Commands
    • Select Logic Outputs
• Receiver Functions
  • Commands
    • Select Receiver Activity-Triggered Macros
    • Select Receiver Post-Activity Timers
    • Select COR Pulse-Triggered Macro
    • Select Pulse Parameters
    • Enable/Disable End-of-Transmission Command Execution
    • Select From-Start-of-Transmission Timer
• Transmitter Functions
  • Transmitter Tail Sequence
    • Courtesy Delay and Courtesy Message
    • Dropout Delay and Dropout Message
    • Transmitter Timeout Timer and Timeout Message
    • Transmitter Unkey Delay
  • Commands
    • Select Courtesy Delay
    • Select Dropout Delay
    • Select Transmitter Timeout Timer
    • Reset Transmitter Timeout Timer
    • Enable/Disable Transmitter
    • Key Transmitter (Timed)
    • Key Transmitter (Untimed)
    • Enable/Disable Transmitter Minimum Unkey Delay
    • Select Transmitter Minimum Unkey Delay
    • Select Receiver-to-Transmitter-Triggered Macros
    • Select Transmitter PTT-Triggered Macros
  • Example: CTCSS Encode Control
• Repeater Functions
  • Commands
    • Select Repeater Access Mode (Path 1)
    • Select Repeater Activity-Triggered Macros
    • Select Repeater Activity Counter/Timer
    • Select Anti-Kerchunker Parameters
    • Select Anti-Kerchunk No Hangtime Mode
    • Select (Review) Courtesy Messages
    • Select Repeater Action-Triggered Macros
• Base Station Functions
  • Commands
    • Enable/Disable Star/Pound Talkout
    • Select Talkout Transmitter Mode
    • Enable/Disable Command Execution on Interdigit Timer
• User Timers
  • Commands
    • Select Timeout Value
    • Select Timer Event Macro
    • Stop Timer
    • Start Timer (Retriggerable)
    • Start Timer (One-Shot)
  • Example: Fan Control
  • Example: An Activity Timer
• Remote Base Interface
  • Remote Base Setup and Configuration
    • Wiring
    • Switch Setting
    • Software Configuration
    • Event-Triggered Macros
  • User Functions: Controlling the Radios
  • Defining Memory Channels using Macros
  • RBI-1 User Function Outputs
  • Commands
    • Assign Remote Base Password
    • Select Remote Base Access-Triggered Macro
    • Select Remote Base Dump-Triggered Macro
    • Select (Review) Remote Base Off Message
    • Reset RBI-1
    • Enable/Disable Access to the Remote Base
    • User Function: Access Remote Base
    • User Function: Dump Remote Base
    • User Function: Speak Radio Configuration
    • User Function: Select Memory Channel and Band
    • User Function: Select VFO Frequency and Offset
    • User Function: Select Transmitter Offset
    • User Function: Enable/Disable Transmitter
    • User Function: Enable/Disable Receiver
    • User Function: Enable/Disable Radio Power
    • User Function: Select Transmitter Power Output
    • User Function: Select Frequency of CTCSS
    • User Function: Enable/Disable CTCSS Encoder
    • User Function: Enable/Disable CTCSS Decoder
    • Macro Function: Send Queued Settings
    • Select RBI-1 Number of User Function Outputs
    • Select Individual RBI-1 User Function Outputs
    • Enter RBI-1 User Function Output Group
• Programming Tables
  • CW Character Set Tables
  • Beep Character Set Tables
  • DTMF Character Set Tables
  • Synthesized Speech Vocabulary
  • Message Run-Time Variables
  • Message Control Characters
  • Scheduler Day Code Table
  • Tone Code Table
  • Root Numbers by Number
  • Event Macros by Number
  • Messages by Number
  • Tenth-Second Timers by Number
  • Tenth-Minute Timers by Number
  • Path Access Mode by Number
  • Software Switches by Number
  • Command Quick Reference
• Application Notes
• Installation
• Parts Lists and Schematics