MSC 18K X Manual (Oct 2017) ALI
User Manual: msc-18k-x-manual
Open the PDF directly: View PDF 
.
Page Count: 34
| Download | |
| Open PDF In Browser | View PDF |
Mobile Column Lift Model Sets MSC-18K-X-236, MSC-18K-X-472 & MSC-18K-X-6108 Capacity 18,000lbs / Each Column Installation - Operation – Service Manual IMPORTANT!! READ MANUAL THOROUGHLY BEFORE INSTALLING, OPERATING, SERVICING OR MAINTAINING LIFT Oct. 2017 INDEX PREFACE--------------------------------------------------------------------------- PAGE 2 PRODUCT IDENTIFICATION-------------------------------------------------- PAGE 2 OWNER / EMPLOYER OBLIGATIONS------------------------------------- PAGE 3 IMPORTANT SAFETY INSTRUCTIONS----------------------------------- PAGE 4 LOCATION------------------------------------------------------------------------- PAGE 7 GENERAL INFORMATION ---------------------------------------------------- PAGE 9 SET-UP / INSTALLATION ------------------------------------------------------ PAGE 10 SYSTEM TESTING BEFORE ACTUAL USE------------------------------ PAGE 15 LIFTING OPERATION----------------------------------------------------------- PAGE 20 MAINTENANCE INSTRUCTIONS ------------------------------------------- PAGE 21 SERVICE --------------------------------------------------------------------------- PAGE 22 SYSTEM DIAGNOSTIC MESSAGES -------------------------------------- PAGE 24 EMERGENCY LOWERING PROCEDURE-------------------------------- PAGE 25 EXPLODED VIEWS & PARTS LISTS -------------------------------------- PAGE 26 LIMITED WARRANTY ---------------------------------------------------------- PAGE 34 PREFACE Prior to the operation of your lift make sure that you have read the instructions thoroughly. These instructions are found in this manual. Please note that your warranty can be voided if you do not read the manual and understand its content. If you have any questions, concerning operation, safety or application of your lift, please consult your distributor. PRODUCT IDENTIFICATION 2 MSC-18K-X Oct. 2017 OWNER / EMPLOYER OBLIGATIONS 1. The Owner/Employer shall ensure that lift operators are qualified and that they are trained in the safe use and operation of the lift using the manufacturer’s operating instructions; ALI/SM10-1, ALI Lifting it Right safety manual; ALI/ST-10 ALI Safety Tips card; ANSI/ALI ALOIM-2008 (R2013), American National Standard for Automotive Lifts - Safety Requirements for Operation, Inspection and Maintenance; ALI/WL400 Series, ALI Uniform Warning Label Decals/Placards; and in the case of frame engaging lifts, ALI/LP-GUIDE, Vehicle Lifting Points/Quick Reference Guide for Frame Engaging Lifts. 2. The Owner/Employer shall establish procedures to periodically inspect the lift in accordance with the lift manufacturer’s instructions or ANSI/ALI ALOIM-2008 (R2013), American National Standard for Automotive Lifts - Safety Requirements for Operation, Inspection and Maintenance; and the Employer shall ensure that the lift inspectors are qualified and that they are adequately trained in the inspection of the lift. 3. The Owner/Employer shall establish procedures to periodically maintain the lift in accordance with the lift manufacturer’s instructions or ANSI/ALI ALOIM-2008 (R2013), American National Standard for Automotive Lifts - Safety Requirements for Operation, Inspection and Maintenance; and the Employer shall ensure that the lift maintenance personnel are qualified and that they are adequately trained in the maintenance of the lift. 4. The Owner/Employer shall maintain the periodic inspection and maintenance records recommended by the lift manufacturer’s instructions or ANSI/ALI ALOIM-2008 (R2013), American National Standard for Automotive Lifts - Safety Requirements for Operation, Inspection and Maintenance. 5. The Owner/Employer shall display the lift manufacturer’s operating instructions; ALI/SM 10-1, ALI Lifting it Right safety manual; ALI/ST-10 ALI Safety Tips card; ANSI/ALI ALOIM-2008 (R2013), American National Standard for Automotive Lifts - Safety Requirements for Operation, Inspection and Maintenance; ALI/WL Series, ALI Uniform Warning Label Decals/Placards; and in the case of frame engaging lifts, ALI/LP- GUIDE, Vehicle Lifting Points/Quick Reference Guide for Frame Engaging Lifts in a conspicuous location in the lift area convenient to the operator. 3 MSC-18K-X Oct. 2017 6. The Owner/Operator shall provide necessary lockout/tag out means for energy sources per ANSI Z244.1-1982 (R1993), Safety Requirements for the Lockout/Tag out of Energy Sources, before beginning any lift repairs and maintenance. 7. The Owner/Employer shall not modify the lift in any manner without the prior written consent of the manufacturer. IMPORTANT SAFETY INSTRUCTIONS (SAVE THESE INSTRUCTIONS) Please deliver this manual to the lift owner and/or operator along with all other documentation provided with the lift. Failure to operate this equipment as intended may cause injury or death. When using this lift, basic safety precautions should always be followed, including the following: 1. Read all instructions in this manual and on the lift thoroughly before installing, operating, servicing or maintaining the lift. 2. Care must be taken as burns can occur from touching hot parts. 3. Do not operate equipment with a damaged cord or if the equipment has been dropped or damaged – until it has been examined by a qualified service person. 4. Do not let a cord hang over the edge of the table, bench, or counter or come in contact with hot manifolds or moving fan blades. 5. If an extension cord is necessary, a cord with a current rating equal to or more than that of the equipment should be used. Cords rated for less current than the equipment may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled. 6. Always unplug equipment from electrical outlet when not in use. Never use the cord to pull the plug from the outlet. Grasp plug and pull to disconnect. 7. Let equipment cool completely before putting away. Loop cord loosely around equipment when storing. 8. To reduce the risk of fire, do not operate equipment in the vicinity of open containers of flammable liquids (gasoline). 4 MSC-18K-X Oct. 2017 9. Adequate ventilation should be provided when working on operating internal combustion engines. 10. Keep hair, loose clothing, fingers, and all parts of body away from moving parts. 11. To reduce the risk of electric shock, do not use on wet surfaces or expose to rain. 12. Use only as described in this manual. Use only manufacturer’s recommended attachments. 13. ALWAYS WEAR SAFETY GLASSES. Everyday eyeglasses only have impact resistant lenses; they are not safety glasses. 14. Inspect lift daily. Do not operate if it malfunctions or problems have been encountered. Never operate lift if it has broken, damaged or worn parts. 15. Never attempt to overload the lift. The manufacturer’s rated capacity is shown on the identification label on the power side column. Do not override the operating controls or the warranty will be void. 16. Only trained and authorized personnel should operate the lift. Do not allow customers or bystanders to operate the lift or be in the lift area. 17. Position the lift support pads to contact the vehicle manufacturers recommended lifting points. Raise the lift until the pads contact the vehicle. Check pads for secure contact with the vehicle. 18. CAUTION! Never work under the lift unless the mechanical safety locks are engaged. 19. Note that the removal or installation of some vehicle parts may cause a critical load shift in the center of gravity and may cause the vehicle to become unstable. Refer to the vehicle manufacturer’s service manual for recommended procedures. 20. Always keep the lift area free of obstruction and debris. Grease and oil spills should always be cleaned up immediately. 21. Never raise vehicle with passengers inside. 22. Before lowering check area for any obstructions. 23. Before removing the vehicle from the lift area, position the columns to prevent damage to the lift and /or vehicle. 5 MSC-18K-X Oct. 2017 24. Check and adjust if need the correct air pressure in all tires before lifting. Do not exceed tire load when raising vehicle. 25. DO NOT raise / lower only one side if a vehicle. 26. Lift only on same axle. Do not stagger between axles. 27. Do not drive over or pinch the electrical communication cables. 28. Do not remove hydraulic fittings while under pressure. 29. Check floor to ceiling height for clearance when vehicle is fully raised. 30. Use only qualified lift service personnel and genuine manufacturing parts to make repairs. WARNING!! Failure by purchaser to provide the recommended mounting surface could result in unsatisfactory lift performance, property damage, or personal injury. 6 MSC-18K-X Oct. 2017 For additional safety instructions regarding lifting, lift types, warning labels, preparing to lift, vehicle spotting, vehicle lifting, maintaining load stability, emergency procedures, vehicle lowering, lift limitations, lift maintenance, good shop practices, installation, operator training and owner/employer responsibilities, please refer to “Lifting It Right” (ALI/SM) and “Safety Tips” (ALI/ST) and vehicle lift points for service garage lifting SAE J2184. For additional instruction on general requirements for lift operation, please refer to “Automotive Lift-Safety Requirements for Operation, Inspection and Maintenance” (ANSI/ALI ALOIM). Installation shall be performed in accordance with ANSO/ALI ALIS, Safety Requirements for Installation and Service of Automotive Lifts. LOCATION This lift has been evaluated for INDOOR USE ONLY with an operating ambient temperature range of 5 - 40°C (41-104°F) ATTENTION! This lift is intended for indoor installation only. It is prohibited to install this product outdoors. Operating environment temperature range should be 41 – 104 °F (5 – 40 °C). Failure to adhere will result in decertification, loss of warranty, and possible damage to the equipment. NOTICE If attachments, accessories, or configuration modifying components used on this lift are located in the load path and affect operation of the lift, affect the lift electrical listing, or affect intended vehicle accommodation; and if they are not certified for use on this lift, then the certification of this lift shall become null and void. Contact the participant for information pertaining to certified attachments, accessories, or configuration modifying components. www.auolift.org © 2011 by ALI, Inc. 7 MSC-18K-X Oct. 2017 ALI/WLSIA01 SAFETY DECALS These Decals Must Be Applied to Lift. REFERENCE: AUTOMOTIVE LIFT INSTITUTE, Inc. NOTE: SOME IMAGES IN THIS MANUAL ARE GENERIC AND MAY NOT RESEMBLE THE LIFT YOU HAVE PURCHASED. 8 MSC-18K-X Oct. 2017 1. GENERAL INFORMATION 1.1 SPECIFICATIONS Models # MSC-18K-X-236, MSC-18K-X-472 & MSC-18K-X-6108 Capacity 18,000 lbs. / Each Column Pressure Relief Valve 2,030 psi Sealed Ex-Works Pump motor 4HP ( 3Kw, DC24V, Max 125 Amp ) / Each Column Battery charger power supply Input: 100-140VAC, 60Hz, Single Phase Output: 24VDC, Max 15 Amp Operational Voltage 24 VDC Lifting Height 67.1" Column L / W / H 56.9” / 44.1” / 88.6” (Max Ht. 155.5”) Fork Adjustable Range 12.6” - 22” Fork length 17.9” Lifting / Lowering Time 100 sec / 60 sec at load of 18,000 lbs / each column Noise Level Max. 70 dB(A) Set-up Indoors Unit Weight 1,548 lbs. per Column Maximum Distance between Columns 32.8' Min. Concrete Surface Strength 3000 Psi 9 MSC-18K-X Oct. 2017 2. SET-UP / INSTALLATION Remark: Only move the lifting column with the forklift. Only raise the lifting column at the correct points. Damage to lifting column and /or injury to persons may occur if the lifting column is not moved in the correct manner. 2.1 PACKING LIST The complete lift is a set of either two (2), four (4) or six (6) mobile column lifting units and one (1) parts box, based on model type. 1. Each column is a self-contained unit. 2. The parts box contains: (Based on Model Type) a) Either - One (1), Three (3) or Five (5) Communication Cable Reels. b) Either - Eight (8), Sixteen (16) or twenty-four (24) Battery Clamps. c) Either – One (1), Two (2) or Three (3) Sets of Combined Seal Washers and Filter Meshes. d) One (1) spare Electro-Magnetic Valve. e) One (1) spare T-Connector. f) Two (2) Keys for Column Door Interlock. g) One (1) Magnet Ring. (Emergency Lowering Procedure) Important document packet that includes, Installation, Operation and Maintenance Manual, ALI Manual, “Lifting it Right”, Automotive Lift Safety Tips Placard, ALI “Lifting Points Guide”, ANSI/ALI ALOIM:2008(R2013) Safety Requirements for Operation, Inspection and Maintenance. Warranty Statement and Warranty Registration Instructions. 2.2 INSTALLATION REQUIREMENTS AND TOOLS / SUPPLIES Foundation Important: It is the user’s responsibility to provide a satisfactory installation area for the lift. Lifts should only be installed on level concrete floors with a minimum thickness of four inches and half (4.5") or 114 mm. Concrete must have a minimum strength of 3000 psi and should be aged thirty (30) days prior to installation. Please consult an architect, contractor or engineer if doubt exists as to the strength and feasibility of the floor to enable proper lift installation and operation. Do not use on asphalt. Do not use on a suspended floor without approval from a licensed structural engineer. A qualified person should be consulted to address seismic loads and other local or state requirements. 10 MSC-18K-X Oct. 2017 It is the user’s responsibility to provide all wiring for electrical hook-up prior to installation and to insure that the electrical installation conforms to local building codes. Where required, it is the user’s responsibility to provide an electrical isolation switch located in close proximity to the lift that will enable emergency stop capability and isolate electrical power from the lift for any servicing requirements. Tools / Supplies 1. Cutting device to remove packaging. 2. Metric wrenches. 3. Allen wrenches. 4. Philips screw drivers. 5. Clean funnel for adding hydraulic oil. 6. Clean new * AW-32 Hydraulic Oil (Hydraulic Oil needed per column 3.6 Gallons / 13.5 Liters) *Note: Use only new fresh clean AW-32 Hydraulic Oil. The use of transmission fluids will void the lift warranty. NOTE: MSC-18K-X Lifts are NOT supplied with Batteries. Customer must supply Batteries as recommended on Page 14. Installation Instructions When the lift arrives on site: Check for any freight damages. The shipment should be thoroughly inspected as soon as it is received. The signed bill of lading is acknowledgement by the carrier of receipt in good condition of shipment covered by our invoice. If any of the goods called for on your bill of lading are shorted or damaged, do not accept them until the carrier makes a notation on the freight bill of the missing or damaged goods. Do this for your own protection. Check the contents of the accessory and hardware boxes to make sure no parts are missing. NOTE: IT IS DIFFICULT TO COLLECT FOR LOSS OR DAMAGE AFTER YOU HAVE GIVEN THE CARRIER A CLEAR RECEIPT. THE LIFT MANUFACTURER IS NOT RESPONSIBLE FOR ANY FREIGHT DAMAGE. 11 MSC-18K-X Oct. 2017 2.3 UNPACKING AND HANDLING THE LIFTING COLUMN Unpacking Procedure • Remove all plastic wrap and cardboard. Be careful not to cut into the lower hydraulic hoses and fittings or to scratch the paint or damage the safety decals. • Carefully open the parts box, avoid cutting the enclosed communication cables. • Take out all of the cable reels, battery clamps, spare parts and document packet. Preparing Lift for Initial Startup To transport the columns to a location within the service facility for setup, please use the pallet jack attached to the column. Each column can be easily moved by lifting up and holding the lever on the handle, by raising up & lowering down the pallet jack handle in a pumping motion, 3-5 times until the column’s central base is lifted from the floor. You can now maneuver the lift columns to any location by pulling the pallet jack handle to the desired location. Once you release the lever on the pallet jack handle, the column will lower down to the ground. The lift shall not be operated unless the column is fully lowered to the ground. Filling the tank with hydraulic oil after the lower column cover is opened and the red plug on the motor pump tank is removed. Use a clean funnel and add new hydraulic oil (AW-32) into the tank. The oil level shall meet the indicating label on the tank. The approx. amount of oil per tank is 3.6Gal / 13.5 Liter. After finished, reinstall the red plug back to the top of the tank. Close motor pump cover and secure with bolts. Note: The hydraulic system was tested during manufacturing. Each hydraulic cylinder and the power unit tank was filled and cycled to test for leaks and for performance. During this process the hydraulic cylinders were bleed to remove any air. The hydraulic oil was removed from the tank after testing. Because residual oil at the bottom of the tank and inside the cylinder remain, additional hydraulic system bleeding is not necessary. To install the batteries, first take away the battery covers on both sides of each column. After the battery is positioned, secure it with the battery clamps provided. Then connect the power cables to the battery terminals. Repeat for other side. Note: Ensure to correctly connect terminals: Red/Pos. = (+), Black/Neg. = (-) 12 MSC-18K-X Oct. 2017 To charge the battery, if necessary. A battery charger is built into each column. Plug the battery charger power supply cord into a 110 volt grounded electrical outlet. Charge each mobile column lifts using a separate electrical outlet. Best performance will be obtained by charging all mobile column batteries at the same time. While charging, the red CHARGING lamp will be lighted. After the batteries are fully charged (about 10 hours), this red lamp will be off and the green FINISHED lamp will be lighted When the lifts are new, charge the batteries for the first time approx. 12-15 hours or until the charging indicator light turns green. Battery charging after 20-30 cycles will typically take 6-8 hours. When the batteries are fully charged, disconnect the electrical cable and store in the charger bay. To install the communication cable reels, first insert the reel holding frame into the base on the upper cover of the column. Then fix the reel on the base by screws. Plug the communication cable end into the socket on that specific column. Please Note the Important Safety Information below for use of Extension Cords: An extension cord should not be used unless absolutely necessary. Use of improper extension cords could result in a risk of fire or electric shock. If extension cords must be used, make sure the following safety precautions are observed. • That the pins of plug of the extension cord are the same number, size and shape of those of the plug on the battery charger. • That the extension cord is properly wired and in good electrical condition. • That the wire in the extension cord is proper size as recommend below. Minimum recommended wire size for various length extension cords used with each battery charger: Length of Cord Cord Gauge 25' 50' 100' 16 Gauge 14 Gauge 12 Gauge • Do not operate the battery charger with a damaged cord or plug. • Do not operate the battery charger if it has received a sharp blow, been dropped or otherwise damaged in any way. • Do not disassemble the charger. Incorrect reassembly may result in a risk of electric shock or fire. • To reduce the risk of electric shock, unplug the charger from outlet before attempting any maintenance or cleaning. Disconnecting the leads will not reduce this risk. • To reduce the risk of shock or spark, never touch the ring terminals together while the charger is plugged into an outlet or extension cord. • External connections to the battery charger shall comply with all local, state, and federal regulations. 13 MSC-18K-X Oct. 2017 WARNING RISK OF EXPLOSIVE GASES WORKING IN THE VICINITY OF A LEAD ACID BATTERY IS DANGEROUS. BATTERIES CONTAIN SULFURIC ACID AND PRODUCE EXPLOSIVE GASES. A BATTERY EXPLOSION COULD RESULT IN LOSS OF EYESIGHT OR SERIOUS BURNS. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS EACH TIME YOU USE THE CHARGER. TO REDUCE THE RISK OF BATTERY EXPLOSION, FOLLOW THESE INSTRUCTIONS AND THOSE PUBLISHED BY THE BATTERY MANUFACTURER FOR ANY EQUIPMENT YOU INTEND TO USE IN THE VICINITY OF THE BATTERY. REVIEW CAUTIONARY MARKINGS ON THESE PRODUCTS AND ON ENGINE, MOTOR OR OTHER EQUIPMENT REQUIRING BATTERY USAGE. Battery Requirement Information: • Battery Quantity: 2ea per MSC Column - (Not included with MSC-18K-X Lifts) • Battery Type: 12VDC Sealed Deep Cycle Battery • Battery Size: BCI Group 31 • Battery Capacity: 105 AH (Amp/Hour) @ 20 HR (Hour Rate) • Battery Terminals: Threaded Stud Terminals 14 MSC-18K-X Oct. 2017 3. System testing before actual use (Do not do any testing with a vehicle) Familiarize yourself with the electronic controls and warning lights by reviewing the functions of each item listed below. 3.1 The Electronic Control Panels: The electronic control system of MSC-18K-X includes one master and either one, three or five slave control panels, based on the model type. Each column has one height sensor, one motor pump, and one electromagnet safety latch. Main Control Panel - #1 Column 15 MSC-18K-X Oct. 2017 Sub Control Panels - #2, #3, #4, #5, #6 Columns 3.2 CONTROL PANEL DETAILS 1. EMERGENCY Button To stop movements (lifting or lowering) immediately. 2. POWER Switch Controls the power of the control panel or charging of the batteries. ⇑ ’ ( UP ) Button 3. ‘⇑ Controls the lifting of the columns. 4. ‘⇓ ⇓ ’ ( DOWN ) Button Controls the lowering of the columns. 5. ‘⇓ ⇓ ’ ( PARK ) Button Controls the locking of the columns. 6. POWER Light This light will go on when the control panel is power on. 7. 8. 9. 10. CURSOR Buttons These buttons move cursor on the screen to edit items. 16 MSC-18K-X Oct. 2017 11. 12. 13. MODE Buttons To select between the functions: “WHEEL”, “AXLE” & “ALL” 14. BIAS Button To set the zero point of height in initialization. 15. START Button To start the running of the software. 16. SHIFT Button This button is for the running of the program. 17. ENTER Button This button serves confirming of instruction or entering sub menu. 18. ESC Button Serves to enter or exit from menu; or from sub menu to upper lever menu. 19. LCD SCREEN Display the height readings of columns & information 20. WARNING Light This light will go on when the EMERGENCY button is pressed. 21. CABLE Port This port is used for communication cable connection. 22. BATTERY Indicator This indicator shows the output voltage of the batteries. 23. LED Light Socket This socket provides the DC power for the LED light. 24. CHARGING Lamp This is to indicate the batteries are in charging. 25. FINISHED Lamp This is to indicate the batteries are fully charged. Note: Before turning on again the Power Switch, please wait for 20 seconds. In “Axle” mode, are always paired as 1# & 2#, 3# & 4#, 5# & 6# per each vehicle axle. In “ALL” mode, all columns move together. In “Wheel” mode, each column moves individually. In case of emergency, push down the ‘EMERGENCY’ button to stop. If any motor does not stop, turn off the battery switch on column’s right side to make an immediate cease. 17 MSC-18K-X Oct. 2017 3.3 COLUMN POSITIONS & CONNECTIONS Depending on the model type, a full combination consists of either 2, 4 or 6 lifting columns. The position of the main column 1# should be located opposite of column 2# loading on the same axel of vehicle. The columns 3# and 4# shall be at wheels of the same axel. If required, the same will apply for columns 5# and 6#. (Figs. 3.3a, b, c) Fig. 3.3a (Two Column Configuration) Fig. 3.3b (Four Column Configuration) Fig. 3.3c (Six Column Configuration) 18 MSC-18K-X Oct. 2017 3.4 OPERATION TEST The mobile column lifts are designed in such a way as to offer maximum flexibility and convenience. A lifting system can consist of 4 lifting columns. The mobile column lifts are set-up as following: 1. Position the lifting columns as indicated in 3.3 (Fig. 3.3.) 2. Then turn on the battery power switch of each column on the side. 3. Set the control box power switch on each sub column to left position (ON) first, the green Power indicators will be on. 4. Then turn on the switch on main column to left (ON) and the LCD screen is lighted. 5. Wait until the LCD screen displays ‘Press START…’, then press the START button to start running of the software. 6. Take care that the emergency stop button of each lifting column must been released. Unloaded Rise: 1. Press and hold the “UP” button on the master 1# column panel, check if the carriages rise normally. Repeat to try the other columns in same way. 2. Press and hold the “UP” button and allow the carriage to rise to its highest position. Check for any hydraulic leaks. Emergency Stop: 1. Push down the red emergency button to stop the lifts while rising. 2. Turn red emergency button to release it after test. Lower Down: 1. Press and hold the “DOWN” button, the carriages will go up a little automatically to disengage the safety locks first, then go down. 19 MSC-18K-X Oct. 2017 Park: 1. Press and hold the ‘Park’ button, the carriage will go down until the safety lock is engaged. Mode ‘Wheel’ or ‘Axle’ test: 1. Press the button ‘Wheel’ or ‘Axle’ or ‘All’ to change mode. 2. In ‘Wheel’ mode, only that button pressed column will operate. 3. In ‘Axle’ mode, only that button pressed pair columns will operate. Note: a. In WHEEL or AXLE mode, the lifting or lowering will be carried out only 5 seconds per time. b. In WHEEL or AXLE mode, the lifting or lowering will be stopped when the height difference between all columns or axles is greater than 2” (50 mm) c. It is normal that during the moving process you may notice one or more columns slow or stop momentary. This occurs when the lift control system is synchronizing each column to maintain leveling. After you have read and understand all of the information in this manual and finished the operations testing you are ready to proceed to lifting vehicles. All technicians that will be using this equipment MUST read and understand all of the safety and operation items in this manual. 4. 4.1 LIFTING OPERATION Load a Vehicle: 1. Check and correct the tire pressure in each tire of the vehicle. 2. Position each mobile column adjacent to each tire on the vehicle. If the vehicle has dual rear axles position the mobile columns to use on the drive axle. Note: If an older vehicle has air bag suspension on the non-drive axles and mobile column are not used, extra support for the axles may be needed to prevent air bag damage. Consult with the vehicle manufacturer to determine if the air bag suspension has mechanical stops. 3. Adjust the lifting arms so they are at the narrowest position that will allow the arms to position under the tires. 4. Move the lifting arms under the vehicle wheels then rest on ground. Note: Always maintain approx. 6 inches of clearance between the column top and the vehicle body. Note: The lift shall not be operated until the columns are fully lowered off dolly wheels. 20 MSC-18K-X Oct. 2017 4.2 Operation 5. Connect all communication cables as show in Fig. 3.3 6. Turn on all the battery switches on columns. Then turn on all the power switch with the master one in the last. 7. Depress the “UP” button and let columns rise approx. 6 inches. Release the “UP” button and inspect all of the columns to insure that the lifting arms are positioned properly. 8. Depress the “UP” button again and raise the vehicle to the desired height. Note: During the raising process you may notice one or more columns slow or stop lifting momentary. This occurs when the lift control system is synchronizing each column to maintain level lifting. This is normal. 9. After reaching to the desired height, press the “PARK” button. All lift columns will lower to the first available safety lock position. When the lifts have settled onto the safety locks release the “Lock” button. The vehicle is now safe and secured and ready for service. 10. To lower the lifts, check that all tools and equipment and has been removed from under the vehicle. Press and hold the “DOWN” button. The lift will rise for a few seconds to allow the safety lock disengaged. Then the lifts will lower down. 11. Before moving out the vehicle, move away all the columns from under the vehicle wheel first. 12. After finished one day’s work, turn off the power switch, disconnect the communication cables, move the columns to the charging bay for charging. 5. Maintenance Instructions CAUTION! If you are not familiar with vehicle lift maintenance, do not attempt repairs and contact the factory/distributor for assistance. Use only experienced lift service technicians to perform lift maintenance. Daily: • Check hydraulic system for leaks. • Check the safety lock mechanism. • Check communication cables for damage • Inspect lifting arms to ensure they are in proper location & engaged in the locks. 21 MSC-18K-X Oct. 2017 Monthly: • Test the emergency stop button on all columns. Columns should stop immediately. • Check the battery charging cables and cable ends. • Inspect communication cables and cable ends for wear or damage. • Check oil levels in hydraulic pump tank. Add oil on necessary. Annually: • Have an ALI Certified Lift inspector check all of your vehicle lifts and the safety systems for wear or damage. 6. Service CAUTION! If you are not familiar with vehicle lift service procedures, do not attempt repairs and contact the factory/distributor for assistance. Use only experienced lift service technicians to perform lift service. Before and vehicle lift is serviced, follow the proper procedure for lock / out tag / out below. Rules for Using Lockout Procedure Use the Lockout Procedure whenever the lift is being repaired or serviced, waiting for repair when current operation could cause possible injury to personnel, or for any other situation when unintentional operation could injure personnel. No attempt shall be made to operate the lift when the energy isolating device is locked out. Purpose This procedure establishes the minimum requirements for the lockout of energy that could cause injury to personnel by the operation of lifts in need of repair or being serviced. All employees shall comply with this procedure. Responsibility The responsibility for assuring that this procedure is followed is binding upon all employees and service personnel from outside service companies (Installers, contactors, service repairmen). All employees shall be instructed in the safety significance of the lockout procedure by the facility owner/manager. Each new or transferred employee along with visiting outside service personnel shall be instructed by the owner/manager (or assigned designee) in the purpose and use of the lockout procedure 22 MSC-18K-X Oct. 2017 Preparation Employees authorized to perform lockout shall ensure that the appropriate energy isolating device (circuit breaker, fuse, disconnect, etc.) is identified for the lift being locked out Other such devices for other equipment may be located in close proximity of the appropriate energy isolating device. If the identity of the device is in question, see the shop supervisor for resolution. Assure that proper authorization is received prior to performing the lockout procedure. Sequence of Lockout Procedure Notify all affected employees that a lockout is being performed and the reason for it. Unload the subject lift. Shut it down and assure the disconnect switch is "OFF" if one is provided on the lift. The authorized lockout person operates the main energy isolation device removing power to the subject lift. If this is a lockable device, the authorized lockout person places the assigned padlock on the device to prevent its unintentional reactivation. An appropriate tag is applied stating the person's name, at least 3"x 6" in size, an easily noticeably color, and states do not operate device or remove tag. If this device is a non-lockable circuit breaker or fuse, replace with a "dummy" device and tag it appropriately as mentioned above. Attempt to operate lift to assure the lockout is working. Be sure to return any switches to the "OFF" position. The equipment is now locked out and ready for the required maintenance or service. Restoring Equipment to Service Assure the work on the lift is complete and the area is clear of tools, vehicles, and personnel. At this point, the authorized person can remove the lock (or dummy circuit breaker or fuse) & tag and activate the energy isolating device so that the lift may again be placed into operation. 23 MSC-18K-X Oct. 2017 7. System Diagnostic Messages The mobile column lifts have self-diagnostic systems that may display a fault message on the LCD screen. Most fault messages indicate some sort of operator error and are designed so the user can correct the most common operation mistakes without employing a service technician. Listed below are the most common fault messages. MESSAGE EXPLAINATION 1 PLC err, check & repower 2 Encode err, WHEEL/AXLE! 3 Asynch! WHEEL / AXLE mode 4 24Vdc insufficient 5 Locked by abnormal ope. 6 Stop! 7 Manual adj.! Max. <5s / time 8 Reset! 9 xx time Reach end of travel xx min. a. Communication between master and slave columns failed. (bad cable connection, antenna problem or some PLC lack of power.) b. Some PLC not working Solution: System must be power off for checking then power on again Some encoder is not working ( not powered, bad wired or in error) Solution: System must be power off for checking then power on again a. Too big difference in height reading (>1700mm), caused by over turning b. Some column not move (motor not running, carriage locked) c. Some encoder not turning (belt left the gear) Solution: The height sensor (encoder) must be reset. After moving stopped, one or more columns were found battery in low voltage. The lift will not raise up any more but may lower down. Solution: To System must be power off for checking then power on again One button is pressed within 2’ after previous button is released. Solution: To press any button on other column control panel. a. Emergency button is pressed. b. Communication between columns is broken. c. One or more column is power off. d. Within 2 second after button is released. Solution: Waiting for 2 seconds. Manually adjust column height. Maximum single operation for 5 seconds per time. Solution: Press more time for more movement. RESET state: one lift height is below 5 cm when in ALL mode. Lift will be back in ZERO bias. Free movement is possible and pair of column can be added or taken away. Note: Any operation will leave this in RESET state. One column stops after reaching its height limit. (this column will not raise when lower down) 24 MSC-18K-X Oct. 2017 8. Emergency - Manual Lowering Procedure WARNING!! THIS PROCEDURE IS RECOMMENDED TO BE PERFORMED BY A QUALIFED SERVICE PERSON AND/OR A FULLY TRAINED OPERATER Note: Before performing this procedure, make sure there are no obstructions that will affect lowering down. In case of an emergency or without power, please use the supplied magnet ring found in the parts box, to lower each column down manually. (Fig. 8.1) 1. Open the lower cabinet, by removing the screws to access the power unit. 2. Locate the solenoid valve coil on the right side of power unit’s valve body, then loosen hex nut to remove the valve coil from the release valve. 3. Place the magnet ring on the release valve’s stem. The release valve will open and the lift column will begin to lower down by gravity. (See Note below) Fig. 8.1 Note: Before placing the magnet ring on release valve stem, ensure the safety latch is not in the locked position, located inside the upper cabinet. 4. Using the key provided to open the upper cabinet door (Fig. 8.2), locate the safety latch mechanism to ensure the safety latch is not in the locked position. (Fig 8.3). 5. If safety latch is in the locked position, pull the electro-magnet pin back by hand and hold to disengage the safety latch to lower. (Fig. 8.4) Fig. 8.2 Fig. 8.3 Fig. 8.4 Note: If a vehicle is loaded on the lift, columns can only be lowered down in 2” (5cm) increments each time, one after another, to keep the vehicle in a safe level position. For procedure assistance, please contact the factory/distributor. 25 MSC-18K-X Oct. 2017 EXPLODED VIEWS & PARTS LISTS Column Assembly Drawing #1 26 MSC-18K-X Oct. 2017 Column Assembly Parts List ITEM 1 2 3 4 5 6 7 8 8-1 9 10 11 12 13 14 15 16 17 18 22 23 24 25 26 27 28 28-1 30 31 32 33 34 35 36 37 38 39 40 41 42 43 43-1 43-2 43-3 Tux P/N MSC-18KX-01-001 MSC-18KX-01-002 MSC-18KX-01-003 MSC-18KX-01-004 MSC-18KX-01-005 MSC-18KX-01-006 MSC-18KX-01-007 MSC-18KX-01-008 MSC-18KX-01-008.1 MSC-18KX-01-009 MSC-18KX-01-010 MSC-18KX-01-011 MSC-18KX-01-012 MSC-18KX-01-013 MSC-18KX-01-014 MSC-18KX-01-015 MSC-18KX-01-016 MSC-18KX-01-017 MSC-18KX-01-018 MSC-18KX-01-022 MSC-18KX-01-023 MSC-18KX-01-024 MSC-18KX-01-025 MSC-18KX-01-026 MSC-18KX-01-027 MSC-18KX-01-028 MSC-18KX-01-028.1 MSC-18KX-01-030 MSC-18KX-01-031 MSC-18KX-01-032 MSC-18KX-01-033 MSC-18KX-01-034 MSC-18KX-01-035 MSC-18KX-01-036 MSC-18KX-01-037 MSC-18KX-01-038 MSC-18KX-01-039 MSC-18KX-01-040 MSC-18K-01X-041 MSC-18KX-01-042 MSC-18KX-01-043 MSC-18KX-01-043.1 MSC-18KX-01-043.2 MSC-18KX-01-043.3 M-Ref P/N DJ02-04000-000 5102-12035-000 DJ02-02003-000 5202-00012-000 DJ02-00011-000 5114-05014-000 DJ02-02001-000 DJ02-02005-000 DJ02-02004-000 DJ02-02000-000 DJ02-00021-000 DJ02-00017-000 5302-00004-000 5306-00004-000 5110-04010-000 5302-00010-000 5102-10035-000 DJ02-19003-M00 5115-06012-000 5110-05014-000 DJ02-00034-000 SJ03-14002-000 DJ02-19001-000 5206-00005-000 DJ02-19002-000 5116-06012-000 DJ02-00039-000 DJ02-19100-A00 5202-00006-000 BZ22-05503-MET BZ22-05514-000 BZ22-05516-000 BZ22-05515-000 5202-00008-000 DJ02-00019-000 DJ02-00016-000 5306-04005-000 5306-00006-000 DJ02-00015-000 DESCRIPTION Right Fork Bolt, M12 x 35mm Nylon Slider Self-Lock Nut, M12 Pin Socket Screw, M5 x 14mm Roller Copper Bushing Washer Carriage Block Plate Teeth Belt Flat Washer, D4 Elastic Washer, D4 Screw, M4 x 10mm Flat Washer, D10 Bolt, M10 x 35mm Right Side Plate Screw, M6 x 12mm Screw, M5 x 14mm Small Hook Fitting Cover Self-Lock Nut, M5 Hinge Hand Screw, M6 x 12mm Nylon Washer Left Side Plate Nut, M6 Battery Switch Fuse Case Copper Plate Fuse, 150A Hex Nut, M8 Gear Electro-Optical Encoder Threaded Pin, M4 x 5mm Spring Washer, D6 Support Board QTY 1 2 2 2 2 28 4 4 4 1 1 1 9 5 8 7 1 1 42 9 2 1 1 1 1 2 4 1 4 1 1 1 1 4 1 1 2 24 1 5110-06020-000 DJ02-11000-000 DJ02-11003-000 DJ02-11100-000 DJ02-11001-000 Screw, M6 x 20mm Wheel Support Shaft Roller Frame Big Roller 2 1 2 1 1 27 MSC-18K-X Oct. 2017 43-4 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 58-1 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 MSC-18KX-01-043.4 MSC-18KX-01-044 MSC-18KX-01-045 MSC-18KX-01-046 MSC-18KX-01-047 MSC-18KX-01-048 MSC-18KX-01-049 MSC-18KX-01-050 MSC-18KX-01-051 MSC-18KX-01-052 MSC-18KX-01-053 MSC-18KX-01-054 MSC-18KX-01-055 MSC-18KX-01-056 MSC-18KX-01-057 MSC-18KX-01-058 MSC-18KX-01-058.1 MSC-18KX-01-059 MSC-18KX-01-060 MSC-18KX-01-061 MSC-18KX-01-062 MSC-18KX-01-063 MSC-18KX-01-064 MSC-18KX-01-065 MSC-18KX-01-066 MSC-18KX-01-067 MSC-18KX-01-068 MSC-18KX-01-069 MSC-18KX-01-070 MSC-18KX-01-071 MSC-18KX-01-072 MSC-18KX-01-073 MSC-18KX-01-074 MSC-18KX-01-075 MSC-18KX-01-076 MSC-18KX-01-077 MSC-18KX-01-078 MSC-18KX-01-079 MSC-18KX-01-080 MSC-18KX-01-081 MSC-18KX-01-082 MSC-18KX-01-083 MSC-18KX-01-084 MSC-18KX-01-085 MSC-18KX-01-086 MSC-18KX-01-087 MSC-18KX-01-088 DJ02-11002-000 DJ02-00018-000 5102-08020-000 5302-00008-000 5901-00010-000 DJ02-00004-000 DJ02-00006-000 5102-05040-000 DJ02-00031-000 5107-03010-000 5306-00008-000 DJ02-00008-000 5402-04030-000 DJ02-01000-MET DJ02-00007-000 QK02-11000-MET DJ02-00007-A00 QK04-00100-M00 Small Roller Weight Bar Bolt, M8 x 20mm Flat Washer, D8 O-Ring, D10 x 2.4 Coil Support Board Electro-Magnet Bolt, M5 x 40mm Coil Fixing Board Screw, M3 x 10mm Spring Washer, D8 Lock Tongue Cotter Pin, D4 x 30mm Column Slip Plate Control Box Cover, HP-22 Cable Reel 1 1 4 8 1 1 1 1 1 4 5 1 1 1 2 1 1 1 SJ03-14001-000 SJ03-14005-000 DJ02-12000-000 DJ02-00030-000 DBZ22B-00 5102-10020-000 DJ02-00033-000 BZ22-05511-000 DJ02-00029-000 DJ02-11000-000 5402-05030-000 DJ02-00001-000 DJ02-00032-000 DJ02-00010-000 DJ02-00009-000 DJ02-03000-000 DJ02-17000-000 5304-00016-000 DJ02-00004-MET 5302-00016-000 DJ02-00014-000 DJ02-06000-000 DJ02-00013-000 5102-16035-000 DJ02-00003-MET DT01-06026-000 DJ02-00019-MET BZ22-05509-MET DJ02-15000-000 T-Fitting Close Nut Oil Pipe Rubber Ring Motor Pump Hex Screw, M10 x 20mm Cover Support Pipe Fixing Frame Pipe Cover Trolley Cotter Pin, D5 x 30mm Pin Shaft Ring, D4 x D35 Chain Left Fork Connecting Frame Circlip, D16 Right, Battery Cover Flat Washer, D16 Bushing Front Wheel Wheel Shaft Hex Bolt, M16 x 35 Left, Battery Cover Nylon Tie Plate Charger Board Battery Charger Fork Pocket 1 1 1 1 1 1 2 1 1 1 2 2 1 4 2 1 1 2 1 2 2 2 2 2 1 1 1 1 2 28 MSC-18K-X Oct. 2017 89 90 91 92 93 94 95 96 97 98 99 100 101 102 106 107 108 109 110 111 112 113 114 115 116 117 118 119 121 122 123 124 125 MSC-18KX-01-089 MSC-18KX-01-090 MSC-18KX-01-091 MSC-18KX-01-092 MSC-18KX-01-093 MSC-18KX-01-094 MSC-18KX-01-095 MSC-18KX-01-096 MSC-18KX-01-097 MSC-18KX-01-098 MSC-18KX-01-099 MSC-18KX-01-100 MSC-18KX-01-101 MSC-18KX-01-102 MSC-18KX-01-106 MSC-18KX-01-107 MSC-18KX-01-108 MSC-18KX-01-109 MSC-18KX-01-110 MSC-18KX-01-111 MSC-18KX-01-112 MSC-18KX-01-113 MSC-18KX-01-114 MSC-18KX-01-115 MSC-18KX-01-116 MSC-18KX-01-117 MSC-18KX-01-118 MSC-18KX-01-119 MSC-18KX-01-121 MSC-18KX-01-122 MSC-18KX-01-123 MSC-18KX-01-124 MSC-18KX-01-125 5306-00010-000 5102-14035-000 DJ02-00036-000 DJ02-00035-000 DJ02-10100-000 5304-00025-000 DJ02-10102-002 DJ02-10002-001 DJ02-10001-000 5906-00070-000 DJ02-05005-000 DJ02-05004-000 DJ02-05102-000 DJ02-09000-000 DJ02-05007-000 DJ02-05011-000 DJ02-05010-000 DJ02-05008-000 DJ02-00027-000 5105-08025-000 DJ02-05003-000 DJ02-05009-000 DJ02-05002-000 5903-00795-000 DJ02-05002-000 BZ22-05508-000 BZ22-00002-000 SL02-00041-A00 5206-00004-000 5110-04010-000 5302-00004-000 5206-00004-000 QK04-80001-FJ5 29 MSC-18K-X Oct. 2017 Elastic Washer, D10 Socket Bolt, M14 x 35mm Washer Protecting Board Roller Holder Circlip, D25 Spacer Shaft Roller Dust Ring, D70 Guide Belt - #2 Guide Ring Cylinder Body Safety Valve Combined Washer Oil Screw Connector Oil Fitting Cylinder Fixing Board Hex Screw, M8 x 25mm Piston Rod Position Bushing Guide Belt - #1 Seal Ring Piston Battery Hose Clamps Socket LED Lamp Socket, M4 Screw, M4 x 10mm Flat Washer, D4 Lock Nut, M4 LED Lamp, 24VDC/27W 6 2 2 1 1 2 2 1 1 1 1 1 1 1 4 1 1 1 1 1 1 1 2 1 1 2 4 1 2 4 8 4 1 Control Panel Assembly Drawing #2 30 MSC-18K-X Oct. 2017 Control Panel Assembly Parts List ITEM 1-1 1-2 1-3 2 3 4 4-1 4-2 5 6 7 8-1 8-2 9 10 11 12 14 15 16 17 21 22 24-1 24-2 25 26 26-1 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Tux P/N MSC-18KX-02-001.1 MSC-18KX-02-001.2 MSC-18KX-02-001.3 MSC-18KX-02-002 MSC-18KX-02-003 MSC-18KX-02-004 MSC-18KX-02-004.1 MSC-18KX-02-004.2 MSC-18KX-02-005 MSC-18KX-02-006 MSC-18KX-02-007 MSC-18KX-02-008.1 MSC-18KX-02-008.2 MSC-18KX-02-009 MSC-18KX-02-010 MSC-18KX-02-011 MSC-18KX-02-012 MSC-18KX-02-014 MSC-18KX-02-015 MSC-18KX-02-016 MSC-18KX-02-017 MSC-18KX-02-021 MSC-18KX-02-022 MSC-18KX-02-024.1 MSC-18KX-02-024.2 MSC-18KX-02-025 MSC-18KX-02-026 MSC-18KX-02-026.1 MSC-18KX-02-027 MSC-18KX-02-028 MSC-18KX-02-029 MSC-18KX-02-030 MSC-18KX-02-031 MSC-18KX-02-032 MSC-18KX-02-033 MSC-18KX-02-034 MSC-18KX-02-035 MSC-18KX-02-036 MSC-18KX-02-037 MSC-18KX-02-038 MSC-18KX-02-039 MSC-18KX-02-040 MSC-18KX-02-041 MSC-18KX-02-042 M-Ref P/N DJ02-20002-000-Grn DJ02-20002-000-Blu DJ02-20002-000-Blk DJ02-20003-000 DJ02-20010-000 5110-00004-000 5203-00004-000 5202-00004-000 QK04-00012-000 DJ02-20006-000 DJ02-20005-000 DJ03-13001-000 QK02-11100-MET 5110-03008-000 QK02-20200-L60 QK02-10013-000 5110-03015-000 5202-00003-000 DJ04-20001-100 QK04-00011-000 DJ02-00200-000 DT01-06023-000 QK04-30300-000 DJ02-10002-000M DJ02-10002-000S DJ02-10032-000 QK04-13300-MZ2 JK01-10113-100 5202-00006-000 5110-04004-000 JK01-10010-000 JK01-JD000-000 QK06-10001-100 5301-00005-000 QK05-20006-H00 QK05-20005-H00 QK04-80002-FJ5 QK04-00015-000 QK04-50700-M00 JK01-00004-000 QK04-50800-M00 DJ02-00007-000 QK04-00013-M00 QK04-30100-M00 31 MSC-18K-X Oct. 2017 DESCRIPTION Operation Button, Green Operation Button, Blue Operation Button, Black Emergency Button, Red Screen, Main Screw, M4 x 12mm Spring Washer, D4 Nut, M4 Battery Meter Indicator Red Lamp Indicator Green Lamp Indicator Main Panel (Sub) Case Bolt, M3 x 8mm Connecting PCB Spacer, M3 x 10mm Screw, M3 x 15mm Nut, M3 Power Switch Plug Cover, D16 Coil Cable Cable Nut, M16 Charger Cable, Red / Black PLC (Main) PLC (Sub) Screw, 3.5 x 15mm Main PCB Delay Fuse, D5 x 20mm Nut, M6 Screw Earthling End Ground Label Bottom Plate Flat Washer, D5 Battery Charger Indicator - Red Battery Charger Indicator - Green LED Lamp Socket, 12-24VDC LED Lamp Cable, Red / Black Cable XS1, 11.8” Cable Nut, M20 Cable XS7, 3.9” Cable Nut, M25 Battery Indicator Cable, 53” Control Panel Cable, 25.6” QTY 1 1 1 1 1 2 2 2 1 1 1 1 1 12 1 8 6 6 1 1 1 2 1 1 1 2 1 1 8 2 1 1 1 2 1 1 1 1 1 2 1 1 1 1 Power Unit Assembly Drawing #3 32 MSC-18K-X Oct. 2017 Power Unit Assembly Parts List ITEM 1 2 3 4 5 5-1 5-2 5-3 6 6-1 6-2 6-3 7 8 9 10 11 12 13 13-1 14 15 16 17 17-1 17-2 18 19 20 21 22 23 24 26 27 28 29 30 31 Tux P/N MSC-18KX-03-001 MSC-18KX-03-002 MSC-18KX-03-003 MSC-18KX-03-004 MSC-18KX-03-005 MSC-18KX-03-005.1 MSC-18KX-03-005.2 MSC-18KX-03-005.3 MSC-18KX-03-006 MSC-18KX-03-006.1 MSC-18KX-03-006.2 MSC-18KX-03-006.3 MSC-18KX-03-007 MSC-18KX-03-008 MSC-18KX-03-009 MSC-18KX-03-010 MSC-18KX-03-011 MSC-18KX-03-012 MSC-18KX-03-013 MSC-18KX-03-013.1 MSC-18KX-03-014 MSC-18KX-03-015 MSC-18KX-03-016 MSC-18KX-03-017 MSC-18KX-03-017.1 MSC-18KX-03-017.2 MSC-18KX-03-018 MSC-18KX-03-019 MSC-18KX-03-020 MSC-18KX-03-021 MSC-18KX-03-022 MSC-18KX-03-023 MSC-18KX-03-024 MSC-18KX-03-026 MSC-18KX-03-027 MSC-18KX-03-028 MSC-18KX-03-029 MSC-18KX-03-030 MSC-18KX-03-031 M-Ref P/N BZ22-05001-300 BZ01-04008-000 5901-00118-000 BZ22-04001-F00 BZ20-04002-000 5901-00160-000 5901-00125-000 5901-00095-000 BZ20-04024-100 5901-00190-000 5901-00130-000 5901-00130-000 5601-00800-000 5109-10010-000 BZ22-00003-B00 5901-00277-000 5901-00925-000 BZ01-03000-F00 BZ20-01000-000 BZ01-01002-000 5301-00006-000 5303-00006-000 5101-06012-000 BZ20-02100-300 DJ02-00042-000 BZ20-02101-000 BZ20-02200-000 5901-01120-000 5105-08080-000 BZ20-00001-000 BZ01-04011-000 BZ13-04100-000 BZ20-04026-000 BZ20-04007-000 BZ22-05008-B00 BZ22-05002-001 5105-05030-000 5105-06025-000 BZ22-05003-000 DESCRIPTION DC Motor, 24VDC, 3KW, 125A Close Nut, 9/16-18 UNF O-Ring, D11.8 x D1.8 Valve Block Overflow Valve, 25Mpa O-Ring, D16 x D2 Circlip, D12 x 1.5mm O-Ring, D9.5 x D1.8 Main, Flow Control Valve O-Ring, D19 x D2 Circlip, D13 x 1.5mm O-Ring, D13 x D1.8 Steel Ball, D8 Threaded Pin, M10x1x10 Connecting Rod, D20 x 34.5mm O-Ring, D27.7 x D2.4 O-Ring, D9.25 x D1.78 Gear Pump, 21Mpa Suction Pipe, D18 x 350mm Filter Washer, D6 Elastic Washer, D6 Bolt, M6 x 12mm Oil Tank Fluid Level Indicator Outlet Plug, M12 x 10mm Tank Cover O-Ring, D112 x D3.55 Screw, M8 x 80mm Return Pipe, D10 x 260mm Filter Solenoid Release Valve, 24VDC Sub, Flow Control Valve Check Valve Motor Adaptor Plate Unipolar DC Contactor, 24VDC, 200A Screw, M5 x 30mm Screw, M6 x 25mm Contactor Support 33 MSC-18K-X Oct. 2017 QTY 1 1 1 1 1 4 3 3 1 1 1 1 3 3 1 1 1 1 1 1 4 4 4 1 1 1 1 1 2 2 2 2 1 1 1 1 4 4 1 LIMITED WARRANTY Structural Warranty: The following parts and structural components carry a five year warranty: Columns Legs Tracks Arms Carriages Cross Rails Uprights Overhead Beam Top Rail Beam Swivel Pins Limited One-Year Warranty: Tuxedo Distributors, LLC (iDEAL) offers a limited one-year warranty to the original purchaser of Lifts and Wheel Service equipment in the United States and Canada. Tuxedo will replace, without charge, any part found defective in materials or workmanship under normal use, for a period of one year after purchase. The purchaser is responsible for all shipping charges. This warranty does not apply to equipment that has been improperly installed or altered or that has not been operated or maintained according to specifications. Other Limitations: This warranty does not cover: 1. Parts needed for normal maintenance 2. Wear parts, including but not limited to cables, slider blocks, chains, rubber pads and pulleys 3. Replacement of lift and tire changer cylinders after the first 30 days. A seal kit and installation instructions will be sent for repairs thereafter. 4. On-site labor Upon receipt, the customer must visually inspect the equipment for any potential freight damage before signing clear on the shipping receipt. Freight damage is not considered a warranty issue and therefore must be noted for any potential recovery with the shipping company. The customer is required to notify Tuxedo of any missing parts within 72 hours. Timely notification must be received to be covered under warranty. Tuxedo will replace any defective part under warranty at no charge as soon as such parts become available from the manufacturer. No guarantee is given as to the immediate availability of replacement parts. Tuxedo reserves the right to make improvements and/or design changes to its lifts without any obligation to previously sold, assembled or fabricated equipment. There is no other express warranty on the Tuxedo lifts and this warranty is exclusive of and in lieu of all other warranties, expressed or implied, including all warranties of merchantability and fitness for a particular purpose. To the fullest extent allowed by law, Tuxedo shall not be liable for loss of use, cost of cover, lost profits, inconvenience, lost time, commercial loss or other incidental or consequential damages. This Limited Warranty is granted to the original purchaser only and is not transferable or assignable. Some states do not allow exclusion or limitation of consequential damages or how long an implied warranty lasts, so the above limitations and exclusions may not apply. This warranty gives you specific legal rights and you may have other rights, which may vary from state to state. 1905 N Main St Suite C, Cleburne, TX 76033 Ph 817-558-9337 / Fax 817-558-9740 34 MSC-18K-X Oct. 2017
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 34 Page Mode : UseNone Producer : EXP Systems LLC (www.exp-systems.com) Create Date : 2017:10:03 14:34:58 Modify Date : 2017:10:03 14:35:14+05:00 Title : MSC-18K-X Manual (Oct 2017) ALI Creator : PDF reDirect v2EXIF Metadata provided by EXIF.tools