GM Service Manuals DC98 Paintspec
User Manual: DC98
Open the PDF directly: View PDF 
.
Page Count: 46
GM Approved
Refinish Materials
GM Approved
Refinish Materials
GENERAL MOTORS CORPORATION
OCTOBER 2003
PRINTED IN USA
GM4901M-D-2004
2k4PaintCov.ai
9/05/03
4 color process
2004 GM Approved Refinish Materials
Foreword
The products listed in this booklet have been approved by GM following a
thorough, standardized test process to meet the GM4901M Specification.
Only the products listed, and their support products (i.e., reducers) can be
used for GM warranty work. This booklet supersedes previous publications.
Primers, surfacers, sealers, basecoats and clearcoats approved to meet
this specification create a complete ″SYSTEM″and are not interchangeable.
Mixing products from different manufacturer-approved lines or the use of
any generic substitutions is strictly forbidden. Unapproved substitution will result
in voiding the manufacturers’ warranty and a loss of GM-approved payments
(chargebacks) for warranty work.
This booklet contains product information based on the latest data available
at the time of publication approval. The right is reserved to make product
or publication changes at any time, without notice. This booklet, or any portions
thereof, may not be reproduced without the written consent of General Motors
Corporation.
Published by North American Operations,
General Motors Corporation, Warren, Michigan 48090-9003
© 2003 General Motors Corporation. All rights reserved. All brands and product
names are registered trademarks of their respective owners.
Information cutoff date 9-18-03.
PRINTED IN U.S.A.
i
Table Of Contents
1. Introduction ..............................................................................1-1
The Bottom Line .......................................................................1-1
2. Approved Paint Systems ..........................................................2-1
Paint Manufacturers ............................................................... .. 2-1
Testing for the GM4901M Specification ...................................... ..2-1
System Categories ................................................................ .. 2-2
Akzo Nobel Coatings, Inc. ....................................................... .. 2-3
BASF .................................................................................. .. 2-6
DuPont .................................................................................2-12
Martin-Senour ..................................................................... .. 2-16
Nexa Autocolor ................................................................... .. 2-19
PPG .....................................................................................2-24
Sherwin-Williams ................................................................. .. 2-31
Standox ............................................................................. .. 2-34
Spies Hecker ...................................................................... .. 2-37
Contacts
For further information on paint suppliers, go to the following web sites:
Akzo Nobel Coatings ....................... www.akzonobelcarrefinishes.net
BASF ................................................................. www.basfrefinish.com
DuPont Performance Coatings
............ DuPont ............................................ www.dupontfinishes.com
............ Standox, Inc. ......................................... www.standoxna.com
............ Spies Hecker, Inc. ........................ www.spiesheckerusa.com
PPG
............ Nexa Autocolor ................................. www.nexaautocolor.com
............ PPG ....................................................... www.ppgrefinish.com
Sherwin Williams
............ Martin Senour .................... www.martinsenour-autopaint.com
............ Sherwin Williams ..................... www.sherwin-automotive.com
ii
1. Introduction
General Motors continuously pursues quality improvement. Therefore GM has
established automotive refinishing standards for itself as well as its Marketing
Division Dealers and Retailers. GM was the first domestic car company to set a
specification for aftermarket paint finishes.
GM has established standards for paint refinishing. Each Division requires the
Dealer to use only materials and methods that meet GM Standard GM4901M
when repairing, replacing, or refinishing vehicles. Where it is determined that
the Dealer is using paint systems or materials which do not meet GM4901M
standards, appropriate counsel and/or corrective action may be taken.
The Bottom Line
The Dealer or Retailer must ensure that all finish repairs, including sublets,
meet GM Specification GM4901M. Use of materials (and associated methods)
that do not meet this GM standard may result in a review of claim(s) leading
to chargeback(s).
As warranty periods increase, customer expectations continue to rise.
Many Dealers/Retailers understand customer expectations. As a result, they
have chosen a single, complete system approach and only use the systems
that meet the highest standards of quality and durability.
All the paint manufacturers that meet the GM4901M Specification have spent
thousands of manhours in research and development to ensure the approved
system gives the appearance, performance, and durability comparable to
the OEM finish. The products in the systems listed in this book are the very
best products to use. They are guaranteed to produce the consistent, quality
results that GM customers expect. This makes it easier for you, as the
Dealer/Retailer, to confidently choose a system that will maximize your
customers’ satisfaction.
Each year, all new paint systems will be tested and evaluated. New or improved
products will also be tested. The paint systems that pass this annual testing
process will be published in this booklet, updated annually.
1-1
1. Introduction
The National Rule was implemented in January 1999. You are required to
use only VOC systems listed in this book for business in the United States.
Some non-VOC systems that meet GM4901M Specifications are still approved
for Canada. Check with your paint supplier to see if a listed non-VOC system
is one of those.
If additional booklets are needed, contact
your paint manufacturer’s representative.
A down-loadable PDF of this booklet is also available at
the GM web site address:
www.gmgoodwrench.com
1-2
2. Approved Paint Systems
Paint Manufacturers
The Manufacturers and their Paint Refinish Systems that have passed the
GM4091M Specification are:
Akzo Nobel Coatings, Inc.
BASF
DuPont
Martin-Senour
Nexa Autocolor
PPG
Sherwin-Williams
Standox
Spies Hecker
Testing for the GM4901M Specification
To meet this specification, each manufacturer has conducted the following tests
for their paint refinish systems:
•Tukon Hardness - point of hardness of paint film after cure
•Humidity Adhesion - durability of paint films exposed to rain and damp
weather conditions
•Chip Resistance - resistance of paint films to stone chipping and or small
mars caused by road dirt/gravel
•Cycle Test - durability of paint films going from cold-to-hot-to-cold or
hot-to-cold-to-hot conditions
•Gas Resistance - resistance of paint to staining or softening when
exposed to gasoline
•Chemical Resistance - resistance to environmental chemicals/ products
•Weather Resistance - overall long-term durability of the paint system
as related to cracking, crazing, fading, hazing, fogging or any other
customer dissatisfaction issues
2-1
2. Approved Paint Systems
System Categories
″Rules″involving refinishing products in the United States have been established.
The products in this booklet are grouped as systems. All systems are listed once,
whether they are Non-VOC Regulated or VOC Regulated. VOC Regulated
systems that meet the National Rule are indicated by one bullet (•) to the right
of the Clearcoat. If the system meets National Rule and Rule 45, it has two
bullets (••). Three bullets (•••) means the system meets National Rule, Rule 45,
and Rule 1151. Approved Non-VOC systems, indicated by four stars (****),
can still be used in Canada.
Only products meeting the National Rule or stricter standards may be
manufactured for use in the United States. A brief explanation of each of the
rules follows:
National Rule: Establishes the pounds-per-gallon limits for Volatile Organic
Compound (VOC) emissions, that are released into the
atmosphere during several steps of the refinishing process.
The regulation focuses on paint manufacturers by prohibiting
the production of noncompliant materials. State and local
regulations will take precedence if they are more strict.
The National Rule takes effect in non-regulated states and
in those states with less restrictive regulations.
Rule 45: Bay Area Air Quality Management District (B.A.A.Q.M.D.)
concerns VOC emissions in the San Francisco Bay area.
It is stricter than the National Rule.
Rule 1151: South Coast Air Quality Management District (S.C.A.Q.M.D.)
concerns VOC emissions for Los Angeles. It is the most
strict for VOC emissions of the VOC regulated products.
Check with your paint supplier to see if the system you are using meets the
VOC requirement of your area.
There may be more than one paint system in a manufacturer’s line that has met
the GM4901M Specification. Each system listed is complete, as tested, and
no substitution, even of a similar product in another system, is acceptable.
The manufacturers and their GM approved systems are laid out on the following
pages for your ease of reference.
2-2
2. Approved Paint Systems
Akzo Nobel Coatings, Inc.
Rigid Substrates* (Steel and Aluminum)
Clearcoat • Autoclear II OE
Basecoat Autobase
Surfacer Colorbuild
Anti-Corrosion Primer # Washprimer CR
* See Akzo Nobel OE Warranty Technical Manual for all mixing and use instructions.
To meet GM4901M Specifications a hardener must be used in the basecoat.
# Primer can be used direct to aluminum.
• VOC Regulated - National Rule
2-3
2. Approved Paint Systems
Akzo Nobel Coatings, Inc. – Rigid Substrates*
(Steel and Aluminum) (Cont’d)
Clearcoat Autoclear III
Basecoat Autobase Plus
Surfacer Colorbuild
Anti-Corrosion Primer # Washprimer CR
Clearcoat •• Autocoat ll LV
Basecoat Autobase
Surfacer Colorbuild 2.1-2.8
Anti-Corrosion Primer # Washprimer CR
Clearcoat ••• Autoclear II LV
Basecoat Autobase
Surfacer Colorbuild 2.1-2.8
Anti-Corrosion Primer # Washprimer EMCF
Clearcoat ••• Autoclear ll LV
Basecoat Autobase Plus
Surfacer Colorbuild 2.1-2.8
Anti-Corrosion Primer # Washprimer EMCF
* See Akzo Nobel OE Warranty Technical Manual for all mixing and use instructions.
To meet GM4901M Specifications a hardener must be used in the basecoat.
# Primer can be used direct to aluminum.
•• VOC Regulated - National Rule and Rule 45
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-4
2. Approved Paint Systems
Akzo Nobel Coatings, Inc. –
Flexible Substrates*
Clearcoat • Autoclear II OE
Basecoat Autobase
Surfacer Colorbuild
Adhesion Primer Primer PO
Clearcoat • Autoclear III
Basecoat Autobase Plus
Surfacer Colorbuild
Adhesion Primer Primer PO
Clearcoat ••• Autoclear II LV
Basecoat Autobase
Surfacer Colorbuild 2.1-2.8
Adhesion Primer Primer PO
Clearcoat ••• Autocoat ll LV
Basecoat Autobase Plus
Surfacer Colorbuild 2.1-2.8
Adhesion Primer Primer PO
* See Akzo Nobel OE Warranty Technical Manual for all mixing and use instructions.
To meet GM4901M Specifications a hardener must be used in the basecoat.
• VOC Regulated - National Rule
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-5
2. Approved Paint Systems
BASF
Rigid Substrates (Steel and Aluminum)
R-M Systems
Clearcoat • DC92 Low VOC Clear
DC5100 CTR Clear
DC5300 CTR Baking Clear
Basecoat DIAMONT Basecoat
Primer DP20 Diamond Primer #
DS30 Diamond Transparent Sealer #
DP26 Power Fill 2K Primer
Anti-Corrosion Primer DE15 Epoxy Primer Surfacer
DE40 Epoxy Primer Surfacer
• VOC Regulated - National Rule
# These primers can be used direct to aluminum using appropriate special hardeners.
To meet GM4901M Specifications a hardener must be used in the basecoat.
2-6
2. Approved Paint Systems
BASF – Rigid Substrates (Steel and Aluminum)
R-M Systems (Cont’d)
Clearcoat • DC92 Low VOC Clear
DC5100 CTR Clear
DC5300 CTR Baking Clear
Basecoat DIAMONT Basecoat
Primer DP21 2K Tintable Urethane Sealer #
Anti-Corrosion Primer DE17
Clearcoat • DC92 Low VOC Clear
DC5100 CTR Clear
DC5300 CTR Baking Clear
Basecoat DIAMONT Basecoat
Primer NP80 High-Build Primer (non-iso)
Anti-Corrosion Primer EP689 Epoxy Primer
Clearcoat •• DC95 3.5 VOC Urethane Clear
DC98 Low VOC Clear
DC5300 CTR Baking Clear
Basecoat DIAMONT Basecoat
Primer DP200 Low VOC Primer #
Anti-Corrosion Primer DE15 Epoxy Primer Surfacer
DE17 Diamond Etching Primer #
Clearcoat •• DC98 Low VOC (2.0) Clear
DC95 3.5 VOC Urethane Clear
Basecoat DIAMONT Basecoat
Primer –
Anti-Corrosion Primer EP359 Low VOC Epoxy Primer
• VOC Regulated - National Rule
•• VOC Regulated - National Rule and Rule 45
# These primers can be used direct to aluminum using appropriate special hardeners.
To meet GM4901M Specifications a hardener must be used in the basecoat.
2-7
2. Approved Paint Systems
BASF – Rigid Substrates (Steel and Aluminum)
R-M Systems (Cont’d)
Clearcoat ••• DC98 Low VOC (2.0) Clear
Basecoat DIAMONT Basecoat
Primer –
Anti-Corrosion Primer DP210 Low VOC Primer #
Clearcoat ••• DC98 Low VOC (2.0) Clear
Basecoat DIAMONT Basecoat
Primer DP200 Low VOC Primer
Anti-Corrosion Primer DE17 Diamond Etching Primer #
••• VOC Regulated and Rule 45 and Rule 1151
# These primers can be used direct to aluminum using appropriate special hardeners.
To meet GM4901M Specifications a hardener must be used in the basecoat.
2-8
2. Approved Paint Systems
BASF – Rigid Substrates
(Steel and Aluminum)
Glasurit Systems
Clearcoat • 923-94 HS Clear
923-550 Fast Urethane Acrylic Clear
923-450 Multi Temp Baking Urethane
Acrylic Clear
923-155 Urethane Acrylic Clear
923-109 HS UV Klarlack (3.5 VOC)
Basecoat Line 55 Basecoat
Primer 285-50 HS Primer #
285-60 Universal HS Primer #
285-0 2K Transparent Filler #
Anti-Corrosion Primer 801-1552 Epoxy Primer Filler EP
(Chromate Free)
Clearcoat •• 923-355 HS Urethane Clear
923-200 Ultra Low VOC Clear
923-109 HS UV Klarlack (3.5 VOC)
Basecoat Line 55 Basecoat
Primer 285-21 2.1 VOC Primer #
Anti-Corrosion Primer 801-1552 Epoxy Primer Filler EP
(Chromate Free)
283-155 Etching Primer #
• VOC Regulated - National Rule
•• VOC Regulated - National Rule and Rule 45
# These primers can be used direct to aluminum using appropriate special hardeners.
To meet GM4901M Specifications a hardener must be used in the basecoat.
2-9
2. Approved Paint Systems
BASF – Rigid Substrates (Steel and Aluminum)
Glasurit Systems (Cont’d)
Clearcoat •• 923-355 HS Urethane Clear
923-109 HS UV Klarlack (3.5 VOC)
Basecoat Line 90 Waterborne Basecoat
Primer 285-21 2.1 VOC Primer #
Anti-Corrosion Primer 801-1552 Epoxy Primer Filler EP
(Chromate Free)
283-155 Etching Primer #
Clearcoat ••• 923-355 HS Urethane Clear
923-109 HS UV Klarlack (3.5 VOC)
Basecoat Line 90 Waterborne Basecoat
Primer 285-21 2.1 VOC Primer #
(Do not use over 70-2)
Anti-Corrosion Primer 70-2 2K Waterborne Primer
283-155 Etching Primer #
Clearcoat ••• 923-200 Ultra Low VOC Clear
Basecoat Line 55 Basecoat
Primer 285-21 2.1 VOC Primer #
Anti-Corrosion Primer 283-155 Etching Primer
•• VOC Regulated - National Rule and Rule 45
••• VOC Regulated and Rule 45 and Rule 1151
# These primers can be used direct to aluminum using appropriate special hardeners.
To meet GM4901M Specifications a hardener must be used in the basecoat.
2-10
2. Approved Paint Systems
BASF – Flexible Substrates
R-M Systems
Clearcoat
DC92 Low VOC Clear w/flexibilizing agent
DC98 Low VOC (2.0) Clear w/flexiblizing agent
Basecoat DIAMONT Basecoat
Primer
DP21 2K Urethane Sealer w/flexiblizing agent
Adhesion Promoter 865 Plastic Adhesion Promoter
Glasurit Systems
Clearcoat 923-450 Urethane Clear w/flexiblizing agent
923-109 HS UV Klarlack
Basecoat Line 55 Basecoat
Primer 285-60 Universal HS Primer/Sealer
w/flexiblizing agent
Adhesion Promoter 934-0 1K Plastic Adhesion Primer
Clearcoat 923-109 HS UV Klarlack
Basecoat Line 90 Basecoat
Primer 285-60 Universal HS Primer/Sealer
w/flexiblizing agent
Adhesion Promoter 934-0 1K Plastic Adhesion Primer
To meet GM4901M Specifications a hardener must be used in the basecoat.
2-11
2. Approved Paint Systems
DuPont
Rigid Substrates (Steel and Aluminum)
Clearcoat •
72400S ChromaPremier™ Appearance Clear
Basecoat * ChromaBase
®
BaseCoat Color ″K″Suffix
ChromaPremier™ BaseCoat Color ″F″Suffix
Primer 3240S 2K High Build Primer
Anti-Corrosion Treatment # 22860S Vinyl Wash Primer
* To meet GM4901M Specifications a hardener must be used in the basecoat.
# These primers can be used direct to aluminum.
• VOC Regulated - National Rule
2-12
2. Approved Paint Systems
DuPont − Rigid Substrates
(Steel and Aluminum) (Cont’d)
Clearcoat •
72200S ChromaPremier™ Productive Clear
72400S ChromaPremier™ Appearance Clear
Basecoat *
ChromaPremier™ BaseCoat Color ″F″Suffix
Primer 424xxS ChromaPremier™ Sealer
Anti-Corrosion Treatment
615S or 625S Variprime
®
Self-Etching Primer
Clearcoat
72500S ChromaPremier™ Premium
Appearance Clear plus 2350S Flex Additive
(High Gloss, Non-Textured)
72500S ChromaPremier™ Premuim
Appearance Clear plus 2350S Flex Additive
plus 2380S Texture Additive (Textured)
72500S ChromaPremier™ Premuim
Appearance Clear plus 2350S Flex Additive
plus 2360S Matting Additive (Low Gloss,
Non-Textured)
Basecoat * ChromaPremier™ BaseCoat Color ″F″Suffix
Anti-Chip Primer 220S Stone Chip Primer
Primer 1140S Uro-Primer plus 2350S Flex Additive
Clearcoat ••
72400S ChromaPremier™ Appearance Clear
Basecoat * ChromaPremier™ BaseCoat Color ″F″Suffix
Primer # 25xxS DuPont™ Epoxy DTM Primer/Sealer
Clearcoat ••
72400S ChromaPremier™ Appearance Clear
3600S ChromaClear
®
Low VOC Productive
Basecoat * ChromaPremier™ BaseCoat Color ″F″Suffix
Primer 3240S 2K High Build Primer
* To meet GM4901M Specifications a hardener must be used in the basecoat.
# These primers can be used direct to aluminum.
• VOC Regulated - National Rule
•• VOC Regulated - National Rule and Rule 45
2-13
2. Approved Paint Systems
DuPont − Rigid Substrates
(Steel and Aluminum) (Cont’d)
Clearcoat •• 2100S ChromaClear
®
Multi Use
G2-V4500S ChromaClear
®
Ultra Productive
G2-V4700S ChromaClear
®
Ultra Productive
(HyperCure Air Dry)
Basecoat * ChromaBase
®
BaseCoat Color ″K″Suffix
ChromaPremier™ BaseCoat Color ″F″Suffix
Primer 3240S 2K High Build Primer
Anti-Corrosion Treatment # 22860S Vinyl Wash Primer
Clearcoat •• 2100S ChromaClear
®
Multi Use
Basecoat * ChromaBase
®
BaseCoat Color ″K″Suffix
Primer # 25xxS DuPont™ Epoxy DTM Primer/Sealer
Clearcoat ••• 2100S ChromaClear
®
Multi Use
Basecoat * ChromaBase
®
BaseCoat Color ″K″Suffix
Primer 3240S 2K High Build Primer
Clearcoat **** 7500S ChromaClear
®
7000S ChromaClear
®
8500S ChromaClear
®
Basecoat * ChromaBase
®
BaseCoat Color ″K″Suffix
Primer # 25xxS DuPont™ Epoxy DTM Primer/Sealer
Clearcoat **** 72200S ChromaPremier™ Productive Clear
72400S ChromaPremier™ Appearance Clear
Basecoat * ChromaPremier™ BaseCoat Color ″F″Suffix
Primer 424xxS ChromaPremier™ Sealer
Anti-Corrosion Treatment # 810R or 820R Corlar
®
Wash Primer Filler
* To meet GM4901M Specifications a hardener must be used in the basecoat.
**** Non-VOC Regulated Systems - Canada
# These primers can be used direct to aluminum.
•• VOC Regulated - National Rule and Rule 45
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-14
2. Approved Paint Systems
DuPont – Flexible Substrates
Clearcoat • 72500S ChromaPremier™ Premium
Appearance Clear plus 2350S Flex Additive
(High Gloss, Non-Textured)
72500S ChromaPremier™ Premium
Appearance Clear plus 2350S Flex Additive
plus 2380S Texture Additive (Textured)
72500S ChromaPremier™ Premium
Appearance Clear plus 2350S Flex Additive
plus 2360S Matting Additive (Low Gloss,
Non-Textured)
Basecoat * ChromaPremier™ BaseCoat Color ″F″Suffix
Anti-Chip Primer 220S Stone Chip Primer
Primer 1140S Uro-Primer plus 2350S Flex Additive
Adhesion Promoter 2330S Plas-Stick™ Adhesion Promoter
Clearcoat •• 72400S ChromaPremier™ Appearance
Clear plus 2350S Flex Additive
Basecoat * ChromaPremier™ BaseCoat Color ″F″Suffix
Sealer 2340S Plas-Stick™ Flexible Adhesion Sealer
Adhesion Promoter 2322S Plas-Stick™ Adhesion Promoter
Clearcoat **** 8500S ChromaClear
®
plus
2350S Flex Additive
Basecoat * ChromaBase
®
BaseCoat Color ″K″Suffix
Sealer 2340S Plas-Stick™ Flexible Adhesion Sealer
Adhesion Promoter 2322S Plas-Stick™ Adhesion Promoter
Clearcoat **** 72400S ChromaPremier™ Appearance
Clear plus 2350S Flex Additive
Basecoat * ChromaPremier™ BaseCoat Color ″F″Suffix
Sealer 2340S Plas-Stick™ Flexible Adhesion Sealer
Adhesion Promoter 2322S Plas-Stick™ Adhesion Promoter
* To meet GM4901M Specifications a hardener must be used in the basecoat.
**** Non-VOC Regulated Systems - Canada
• VOC Regulated - National Rule
•• VOC Regulated - National Rule and Rule 45
2-15
2. Approved Paint Systems
Martin-Senour
Rigid Substrates (Steel and Aluminum)
Clearcoat • TC741 Tec/BASE
®
Performance
Urethane Clearcoat
TC730 Tec/BASE
®
Speed Clearcoat
Basecoat * Tec/BASE
®
BaseCoat w / TH121, 122, 123,
124, 704, 8660, 8670 or 8876
Sealer TP520-526 Complete™ Sealer System
5100 2K Urethane Sealer Series
Surfacer TP520-526 Complete™ Primer System
5103 Tint/PRIME
®
Primer/Surfacer
Anti-Corrosion Primer # 8827 Vinyl Wash Etching Primer
8847 TRIO/Prime
®
Etching Filler
TE500 TRIO/Prime
®
Lead & Chromate Free
Etching Filler
* To meet GM4901M Specifications, a hardener must be used in the Base Color.
Add listed Hardeners at a ratio of 2 oz. to a ready-to-spray quart of Tec/BASE
®
Basecoat.
# These primers can be applied direct to aluminum.
• VOC Regulated - National Rule
2-16
2. Approved Paint Systems
Martin-Senour − Rigid Substrates
(Steel and Aluminum) (Cont’d)
Clearcoat •• TC730 Tec/BASE
®
Speed Clearcoat
8955 Tec/BASE
®
3.5 VOC HS Clearcoat
Basecoat * Tec/BASE
®
BaseCoat w / TH121, 122,
123, 124, 704, 8660, 8670 or 8876
Sealer TP520-526 Complete™ Sealer System
5100 2K Urethane Sealer Series
Surfacer TP520-526 Complete™ Primer System
5103 Tint/PRIME
®
Primer/Surfacer
Anti-Corrosion Primer # 8827 Vinyl Wash Etching Primer
8847 TRIO/Prime
®
Etching Filler
TE500 TRIO/Prime
®
Lead & Chromate Free
Etching Filler
Clearcoat ••• 8901V Tec/BASE
®
2.1 VOC Clearcoat
Basecoat * Tec/BASE
®
BaseCoat w / TH121, 122,
123, 124, 704, 8660, 8670 or 8876
Sealer Tec/SHADE™ 2.1 Sealer System
Surfacer Tec/SHADE™ 2.1 Primer System
Anti-Corrosion Primer # TE500 TRIO/Prime
®
Lead & Chromate Free
Etching Filler
* To meet GM4901M Specifications, a hardener must be used in the Base Color.
Add listed Hardeners at a ratio of 2 oz. to a ready-to-spray quart of Tec/BASE
®
Basecoat.
# These primers can be applied direct to aluminum.
•• VOC Regulated - National Rule and Rule 45
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-17
2. Approved Paint Systems
Martin-Senour – Flexible Substrates
Clearcoat ••• TC741 Tec/BASE
®
Performance
Urethane Clearcoat
TC730 Tec/BASE
®
Speed Clearcoat
8955 Tec/BASE
®
3.5 VOC HS Clearcoat
8901V Tec/BASE
®
2.1 VOC Clearcoat
Basecoat * Tec/BASE
®
BaseCoat w / TH121, 122, 123,
124, 704, 8660, 8670 or 8876
Sealer TP520-526 Complete™ Sealer System
Tec/SHADE™ 2.1 Sealer System
5100 2K Urethane Sealer Series
Surfacer TP520-526 Complete™ Primer System
5103 Tint/PRIME
®
Primer/Surfacer
Tec/SHADE™ 2.1 Primer System
Adhesion Promoter 6246 Plastic Adhesion Promoter Clear
6247 Plastic Adhesion Promoter Dk. Gray
5100 2K Ad Pro Series
* To meet GM4901M Specifications, a hardener must be used in the Base Color.
Add listed Hardeners at a ratio of 2 oz. to a ready-to-spray quart of Tec/BASE
®
Basecoat.
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-18
2. Approved Paint Systems
Nexa Autocolor
Rigid Substrates (Steel and Aluminum)
Clearcoat • P190-643 HS Clearcoat
Basecoat * P422 line 2K Basecoat
P965 line Aquabase Basecoat
Sealer P565-357/358 Wet-on-Wet Sealer
P565-3011/3015 Fast HS Wet-on-Wet Sealer
Anti-Corrosion Primer # P565-713 Chromate-Free Etch Primer
*To meet GM4901M Specifications, a hardener must be added to the basecoat.
# The primers can be applied directly to aluminum.
• VOC Regulated - National Rule
2-19
2. Approved Paint Systems
Nexa Autocolor − Rigid Substrates
(Steel and Aluminum) (Cont’d)
Clearcoat • P190-643 HS Clearcoat
Basecoat * P422 line 2K Basecoat
P965 line Aquabase Basecoat
Surfacer P565-693 Hi Dur Rapide
P565-510/511 HS Primer Surfacer
Anti-Corrosion Primer # P565-713 Chromate-Free Etch Primer
Clearcoat • P190-643 HS Clearcoat
Basecoat * P422 line 2K Basecoat
P965 line Aquabase Basecoat
Surfacer ** P110-5000 UV Speedprime
Clearcoat •• P190-6530 HS Plus Clearcoat
Basecoat * P422 line 2K Basecoat
Sealer P565-3111/3115 HS Wet-on-Wet Sealer
Anti-Corrosion Primer # P565-713 Chromate-Free Etch Primer
Clearcoat •• P190-6530 HS Plus Clearcoat
Basecoat * P422 line 2K Basecoat
Surfacer P565-5201/5205 HS Plus Primer Surfacer
Anti-Corrosion Primer # P565-713 Chromate-Free Etch Primer
Clearcoat •• P190-6530 HS Plus Clearcoat
Basecoat * P422 line 2K Basecoat
Surfacer ** P110-5000 UV Speedprime
*To meet GM4901M Specifications, a hardener must be added to the basecoat.
** Spot repair only.
# The primers can be applied directly to aluminum.
• VOC Regulated - National Rule
•• VOC Regulated - National Rule and Rule 45
2-20
2. Approved Paint Systems
Nexa Autocolor – Rigid Substrates
(Steel and Aluminum) (Cont’d)
Clearcoat ••• P190-6730 HS Plus Clearcoat
Basecoat * P422 line 2K Basecoat
Sealer P565-3111/3115 HS Wet-on-Wet Sealer
Anti-Corrosion Primer # P565-713 Chromate-Free Etch Primer
Clearcoat ••• P190-6730 HS Plus Clearcoat
Basecoat * P422 line 2K Basecoat
Surfacer P565-5201/5205 HS Plus Primer Surfacer
Anti-Corrosion Primer # P565-713 Chromate-Free Etch Primer
Clearcoat ••• P190-6730 HS Plus Clearcoat
Basecoat * P422 line 2K Basecoat
Surfacer ** P110-5000 UV Speedprime
*To meet GM4901M Specifications, a hardener must be added to the basecoat.
** Spot repair only.
# The primers can be applied directly to aluminum.
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-21
2. Approved Paint Systems
Nexa Autocolor – Flexible Substrates
Clearcoat • P190-643 HS Clearcoat (flexibilized)
Basecoat * P422 line 2K Basecoat
P965 line Aquabase Basecoat
Sealer P565-357/358 Wet-on-Wet Sealer
(flexibilized)
P565-3011/3015 Fast HS Wet-on-Wet Sealer
(flexibilized)
Adhesion Promoter P573-2001 Adhesion Primer for Plastics
Clearcoat • P190-643 HS Clearcoat (flexibilized)
Basecoat * P422 line 2K Basecoat
P965 line Aquabase Basecoat
Surfacer P565-693 Hi Dur Rapide (flexibilized)
P565-510/511 HS Primer Surfacer
(flexibilized)
Adhesion Promoter P573-2001 Adhesion Primer for Plastics
Clearcoat • P190-643 HS Clearcoat (flexibilized)
Basecoat * P422 line 2K Basecoat
P965 line Aquabase Basecoat
Surfacer ** P110-5000 UV Speedprime
Clearcoat •• P190-6530 HS Plus Clearcoat (flexibilized)
Basecoat * P422 line 2K Basecoat
Sealer P565-3111/3115 HS Wet-on-Wet Sealer
(flexibilized)
Adhesion Promoter P573-2001 Adhesion Primer for Plastics
*To meet GM4901M Specifications, a hardener must be added to the basecoat.
** Spot repair only.
• VOC Regulated - National Rule
•• VOC Regulated - National Rule and Rule 45
2-22
2. Approved Paint Systems
Nexa Autocolor − Flexible Substrates (Cont’d)
Clearcoat •• P190-6530 HS Plus Clearcoat (flexibilized)
Basecoat * P422 line 2K Basecoat
Surfacer P565-5201/5205 HS Plus Primer
Surfacer (flexibilized)
Adhesion Promoter P573-2001 Adhesion Primer for Plastics
Clearcoat •• P190-6530 HS Plus Clearcoat (flexibilized)
Basecoat * P422 line 2K Basecoat
Surfacer ** P110-5000 UV Speedprime
Clearcoat ••• P190-6730 HS Plus Clearcoat (flexibilized)
Basecoat * P422 line 2K Basecoat
Sealer P565-3111/3115 HS Wet-on-Wet Sealer
(flexibilized)
Adhesion Promotor P573-2001 Adhesion Primer for Plastics
Clearcoat ••• P190-6730 HS Plus Clearcoat (flexibilized)
Basecoat * P422 line 2K Basecoat
Surfacer P565-5201/5205 HS Plus Primer Surfacer
(flexibilized)
Adhesion Promotor P573-2001 Adhesion Primer for Plastics
Clearcoat ••• P190-6730 HS Plus Clearcoat (flexibilized)
Basecoat * P422 line 2K Basecoat
Surfacer ** P110-5000 UV Speedprime
*To meet GM4901M Specifications, a hardener must be added to the basecoat.
** Spot repair only.
•• VOC Regulated - National Rule and Rule 45
••• VOC Regulated - National Rule, Rule 45 and Rule
2-23
2. Approved Paint Systems
PPG
Rigid Substrates (Steel and Aluminum)
Deltron Systems
Clearcoat • DCU2002 High Solids Polyurethane Clear
DCU2021 Urethane Clear
DCU2035 3.5 VOC Clear
DCU2042 Low VOC Speed Clear
DCU2055 Clear
DCU2082 StratoClear™
DCD35 3.5 VOC Compliant Clear
Specialty Coating *** DCU2060 Flexed-Flat Clear
Basecoat DBU / DBC * Deltron Basecoat
Primer Surfacer # DS1002 UV Cured Primer Surfacer
* To meet GM4901 Specifications, DX57 must be added to DBC Basecoat.
*** This coating meets the anti-glare safety and elastomeric coating designations.
# These primers can be applied directly to aluminum.
• VOC Regulated - National Rule
2-24
2. Approved Paint Systems
PPG – Rigid Substrates (Steel and Aluminum)
Deltron Systems (Cont’d)
Clearcoat • DCU2082 StratoClear™
Specialty Coating *** DCU2060 Flexed-Flat Clear
Basecoat DBU / DBC * Deltron Basecoat **
Undercoat Primer NPC270 Corrosion Resistant Primer
Anti-Corrosion Primer DPX170 Chrome Self-Etching Primer
DPX171 Non-Chrome Self-Etching Primer
DX1791 Wash Primer
Metal/Aluminum
Treatments # DX533 Aluminum Cleaner /
DX503 Aluminum Conditioner
Clearcoat • DCU2002 High Solids Polyurethane Clear
DCU2021 Urethane Clear
DCU2035 3.5 VOC Clear
DCU2042 Low VOC Speed Clear
DCU2055 Clear
DCU2082 StratoClear™
DCD35 3.5 Compliant Clear
Specialty Coating *** D2060 Flexed-Flat Clear
Basecoat DBU / DBC * Deltron Basecoat **
Surfacer K36 PRIMA™ Acrylic Urethane Primer
Surfacer
Anti-Corrosion Primer DPX170 Chrome Self-Etching Primer
DPX171 Non-Chrome Self-Etching Primer
DX1791 Wash Primer
DPLF Non-Sanding Epoxy Primer
Metal/Aluminum
Treatments # DX533 Aluminum Cleaner /
DX503 Aluminum Conditioner
*To meet GM4901 Specifications, DX57 must be added to DBC Basecoat.
** NCS1990, Compliant Wet-on-Wet Sealer, may be used prior to topcoating.
*** This coating meets the anti-glare safety and elastomeric coating designations.
# These primers can be applied directly to aluminum.
• VOC Regulated - National Rule
2-25
2. Approved Paint Systems
PPG − Rigid Substrates (Steel and Aluminum)
Deltron Systems (Cont’d)
Clearcoat •• DCU2002 High Solids Polyurethane Clear
DCU2021 Urethane Clear
DCU2035 3.5 VOC Clear
DCU2042 Low VOC Speed Clear
DCU2055 Clear
DCU2082 StratoClear™
DCD35 3.5 Compliant Clear
Specialty Coating *** D2060 Flexed-Flat Clear
Basecoat DBU / DBC * Deltron Basecoat
Primer Surfacer # DS1002 UV Cured Primer Surfacer
Clearcoat •• DCU2002 High Solids Polyurethane Clear
DCU2021 Urethane Clear
DCU2035 3.5 VOC Clear
DCU2042 Low VOC Speed Clear
DCU2055 Clear
DCU2082 StratoClear™
DCD35 3.5 Compliant Clear
Specialty Coating *** DCU2060 Flexed-Flat Clear
Basecoat DBU / DBC * Deltron Basecoat **
Undercoat Primer NCP270 Corrosion Resistant Primer
Anti-Corrosion Primer DPX170 Chrome Self-Etching Primer
DPX171 Non-Chrome Self-Etching Primer
DX1791 Wash Primer
DPLF Non-Sanding Epoxy Primer
Metal/Aluminum
Treatments # DX533 Aluminum Cleaner /
DX503 Aluminum Conditioner
*To meet GM4901 Specifications, D888 must be added to BC Basecoat.
** NCS1990, Compliant Wet-on-Wet Sealer, may be used prior to topcoating.
*** This coating meets the anti-glare safety and elastomeric coating designations.
# These primers can be applied directly to aluminum.
•• VOC Regulated - National Rule and Rule 45
2-26
2. Approved Paint Systems
PPG – Rigid Substrates (Steel and Aluminum)
Deltron Systems (Cont’d)
Clearcoat ••• DCU2010 2.1 Speed Clear
DCU2030 3.5 Spot and Panel Clear
Specialty Coating *** DCU2060 Flexed-Flat Clear
Basecoat DBU / DBC * Deltron Basecoat
Primer Surfacer # DS1002 UV Cured Primer Surfacer
Clearcoat ••• DCU2010 2.1 Speed Clear
Specialty Coating *** DCU2060 Flexed-Flat Clear
Basecoat DBU / DBC * Deltron Basecoat **
Undercoat Primer Surfacer NCP280 2.1 VOC Primer Surfacer
Anti-Corrosion Prep DPX170 Chrome Self-Etching Primer
DPX171 Non-Chrome Self-Etching Primer
DX1791 Wash Primer
Metal/Aluminum
Treatments # DX533 Aluminum Cleaner /
DX503 Aluminum Conditioner
Clearcoat ••• DCU2030 3.5 Spot and Panel Clear
Specialty Coating *** DCU2060 Flexed-Flat Clear
Basecoat DBU / DBC * Deltron Basecoat **
Undercoat Primer NCP280 2.1 VOC Primer Surfacer
Anti-Corrosion Prep DPX171 Non-Chrome Self-Etching Primer
Metal/Aluminum
Treatments # DX533 Aluminum Cleaner /
DX503 Aluminum Conditioner
* To meet GM4901 Specifications, D888 must be added to BC Basecoat.
** NCS1990, Compliant Wet-on-Wet Sealer, may be used prior to topcoating.
*** This coating meets the anti-glare safety and elastomeric coating designations.
# These primers can be applied directly to aluminum.
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-27
2. Approved Paint Systems
PPG – Rigid Substrates (Steel and Aluminum)
Global Systems
Clearcoat • D890 Compliant Clear
D893 Low VOC Performance Clear
D894 High Solids Clear
Specialty Coating *** D8102 Matte Clear
Basecoat BC * Basecoat Colour
Envirobase Colour **◆
Primer Surfacer # D8080 UV Cured Primer Surfacer
Clearcoat • D890 Compliant Clear
D893 Low VOC Performance Clear
D894 High Solids Clear
Specialty Coating *** D8102 Matte Clear
Basecoat BC * Basecoat Colour **
Envirobase Colour **◆
Surfacer D839 2K Primer Surfacer
DTM Primer Surfacer
Anti-Corrosion Primer D831 Chrome-Free Wash Primer
Metal/Aluminum
Treatments # DTM Primer Surfacer
Clearcoat • D8101 Fast Clear
Specialty Coating *** D8102 Matte Clear
Basecoat BC * Basecoat Colour **
Envirobase Colour **◆
Undercoat Primer D822 Corrosion Resistant Primer
D839 2K Primer Surfacer
DTM Primer Surfacer
Anti-Corrosion Primer D831 Chrome-Free Wash Primer
Metal/Aluminum
Treatments # DTM Primer Surfacer
*To meet GM4901 Specifications, D888 must be added to BC Basecoat.
** D891, Compliant Sealer, may be used prior to topcoating.
*** This coating meets the anti-glare safety and elastomeric coating designations.
# These primers can be applied directly to aluminum.
• VOC Regulated - National Rule
◆To meet GM4901 Specifications, T588 must be added to Envirobase Colour,
Clearcoats are limited to D890 and D894 with Envirobase Colour.
2-28
2. Approved Paint Systems
PPG − Rigid Substrates (Steel and Aluminum)
Global Systems (Cont’d)
Clearcoat ••• D890 Compliant Clear
D894 High Solids Clear
D8106 2.1 Performance
D8107 Stoving Clear
Specialty Coating *** D8102 Matte Clear
Basecoat BC * Basecoat Colour
Envirobase Colour **◆
Primer Surfacer # D8080 UV Cured Primer Surfacer
Clearcoat ••• D890 Compliant Clear
D894 High Solids Clear
D8106 2.1 Performance
D8107 Stoving Clear
Specialty Coating *** D8102 Matte Clear
Basecoat BC * Basecoat Colour **
Envirobase Colour **◆
Undercoat Primer D8002 Ultra High Solids Surfacer
Anti-Corrosion Primer # D831 Chrome-Free Wash Primer
*To meet GM4901 Specifications, D888 must be added to BC Basecoat.
** D891, Compliant Sealer, may be used prior to topcoating.
*** This coating meets the anti-glare safety and elastomeric coating designations.
# These primers can be applied directly to aluminum.
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
◆To meet GM4901 Specifications, T588 must be added to Envirobase Colour,
Clearcoats are limited to D890 and D894 with Envirobase Colour.
2-29
2. Approved Paint Systems
PPG – Flexible Substrates
Deltron Systems
Clearcoat •• DCU2042 Low VOC Speed Clear
Specialty Coating *** DCU2060 Flexed-Flat Clear
Basecoat DBU / DBC Deltron Basecoat
Primer Surfacer DS1002 UV Cured Primer Surfacer
Clearcoat •• DCU2042 Low VOC Speed Clear
Specialty Coating *** DCU2060 Flexed-Flat Clear
Basecoat DBC Deltron Basecoat *
Flexible Primer Surfacer K36 PRIMA™ Acrylic Urethane Primer
Surfacer reduced with DX814 Universal
Flexibilizer
SX1056 Flexible 2K Sealer
SX1057 Flexible 2K Surfacer
Adhesion Promoter SX1050 Plastic Adhesion Promotor
Global Systems
Clearcoat •• D893 Low VOC Performance Clear
Specialty Coating *** D8102 Matte Clear
Basecoat BC Basecoat Colour *
Primer Surfacer D8080 UV Cured Primer Surfacer
Clearcoat •• D893 Low VOC Performance Clear
Basecoat BC Basecoat Colour *
Flexible Primer Surfacer D839 2K Primer Surfacer reduced
with D814 Plasticiser
SX1056 Flexible 2K Sealer
SX1057 Flexible 2K Surfacer
Adhesion Promoter SX1050 Plastic Adhesion Promoter
* To meet GM4901 Specifications, a basecoat hardener and universal flexibilizer
must be used.
*** This coating meets the anti-glare safety and elastomeric coating designations.
•• VOC Regulated - National Rule and Rule
2-30
2. Approved Paint Systems
Sherwin-Williams
Rigid Substrates (Steel and Aluminum)
Clearcoat • CC930 ULTRA 7000
®
Clearcoat
CC940 ULTRA 7000
®
Clearcoat
Basecoat * ULTRA 7000
®
Basecoatw/UH22,33,44,
55, 60, 70, 80 or 904
Sealer S50 Series
S60 2K Series
P30 SpectraSeal™
Surfacer P30 SpectraPrime™
P47 Color-Prime
®
Tintable Primer Surfacer
Anti-Corrosion Primer # E2G973 Vinyl Wash Etching Primer
E2G980 G.B.P.
®
Etching Filler
PE990 Chrome Free Etching Filler
* To meet GM4901M Specifications, a hardener must be used in the Basecoat.
Add UH Hardeners at a ratio of 2 oz. to a ready-to-spray quart of Ultra 7000
®
Basecoat.
# These primers can be used direct to aluminum.
• VOC Regulated - National Rule
2-31
2. Approved Paint Systems
Sherwin-Williams – Rigid Substrates
(Steel and Aluminum) (Cont’d)
Clearcoat •• CC930 ULTRA 7000
®
Clearcoat
CC350 ULTRA 7000
®
3.5 VOC Clearcoat
Basecoat * ULTRA 7000
®
Basecoatw/UH22,33,44,
55, 60, 70, 80 or 904 *
Sealer S50 Series
S60 2K Series
Surfacer P47 Color-Prime
®
Tintable Primer Surfacer
P30 SpectraPrime™
Anti-Corrosion Primer # E2G973 Vinyl Wash Etching Primer
E2G980 G.B.P.
®
Etching Filler
PE990 Chrome Free Etching Filler
Clearcoat ••• CC210 ULTRA 7000
®
2.1 VOC Clearcoat
Basecoat * ULTRA 7000
®
Basecoatw/UH22,33,44,
55, 60, 70, 80 or 904 *
Sealer P23 UltraShade Sealer™
Surfacer P23 UltraShade Primer™
Anti-Corrosion Primer # PE990 Chrome Free Etching Filler
* To meet GM4901M Specifications, a hardener must be used in the Basecoat.
Add UH Hardeners at a ratio of 2 oz. to a ready-to-spray quart of Ultra 7000
®
Basecoat.
# These primers can be used direct to aluminum.
•• VOC Regulated - National Rule and Rule 45
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-32
2. Approved Paint Systems
Sherwin-Williams − Flexible Substrates
Clearcoat ••• CC940 ULTRA 7000
®
Clearcoat
CC930 ULTRA 7000
®
Clearcoat
CC350 ULTRA 7000
®
3.5 VOC Clearcoat
CC210 ULTRA 7000
®
2.1 VOC Clearcoat
Basecoat * ULTRA 7000
®
Basecoatw/UH22,33,44,
55, 60, 70, 80 or 904 *
Sealer P23 UltraShade Sealer™
P30 SpectraSeal™
S50 Series
Surfacer P30 SpectraPrime™
P47 Color-Prime
®
Tintable Primer Surfacer
P23 UltraShade Primer™
Adhesion Promoter
UPO7226 Plastic Adhesion Promoter Clear
UPO7227 Plastic Adhesion Promoter Dk. Gray
S60 2K Series
* To meet GM4901M Specifications, a hardener must be used in the Basecoat.
Add UH Hardeners at a ratio of 2 oz. to a ready-to-spray quart of ULTRA 7000
®
Basecoat.
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-33
2. Approved Paint Systems
Standox
Rigid Substrates (Steel and Aluminum)
Clearcoat • 2K Clear 20-60
2K MS Clear
2K HS Clear
Basecoat * MSB Basecoat Color with 15% 2K Hardener
Surfacer 2K Nonstop Primer Filler
Anti-Corrosion Primer # Etching Adhesion Primer
* Solventborne basecoat requires the addition of hardener per technical
recommendations.
# Can be used direct to aluminum.
• VOC Regulated - National Rule
2-34
2. Approved Paint Systems
Standox – Rigid Substrates (Steel and Aluminum) (Cont’d)
Clearcoat ••• 2.1 Clear
Basecoat * MSB Basecoat Color w/ 15% 2K Hardener
or Standohyd
®
Basecoat Color
Surfacer 2.1 Filler
Anti-Corrosion Primer # Etching Adhesion Primer
Clearcoat • Standox 2K MS Clear 20-60 plus
2K Plasticiser (High Gloss, Non-Textured)
Standox 2K MS Clear 20-60 plus
2K Plasticiser plus 2K Texture Additive
Coarse – Mix 603 (Textured)
Standox 2K MS Clear 20-60 plus 2K Elastic
Matt – Mix 005 (Low Gloss, Non-Textured)
Basecoat * Standox Basecoat
Anti-Chip Primer Standohyd
®
Stone Chip Primer
Primer Standox 2K Nonstop Primer Filler plus
2K Plasticiser
* Solventborne basecoat requires the addition of hardener per technical
recommendations.
# Can be used direct to aluminum.
• VOC Regulated - National Rule
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-35
2. Approved Paint Systems
Standox – Flexible Substrates
Clearcoat ••• 2K Clear 20-60
Flexible Additive 2K Plasticiser (for surfacer and clearcoat)
Basecoat * MSB Basecoat Color with 15% 2K Hardener
Surfacer 2K Nonstop Primer Filler
Adhesion Primer Standoflex 1K Plastic Primer
Clearcoat • Standox 2K MS Clear 20-60 plus
2K Plasticiser (High Gloss, Non-Textured)
Standox 2K MS Clear 20-60 plus
2K Plasticiser plus 2K Texture Additive
Coarse – Mix 603 (Textured)
Standox 2K MS Clear 20-60 plus 2K Elastic
Matt – Mix 005 (Low Gloss, Non-Textured)
Basecoat * Standox Basecoat
Anti-Chip Primer Standohyd
®
Stone Chip Primer
Primer Standox 2K Nonstop Primer Filler plus
2K Plasticiser
Adhesion Promoter Standoflex
®
Plastic Primer
* Solventborne basecoat requires the addition of hardener per technical
recommendations.
• VOC Regulated - National Rule
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-36
2. Approved Paint Systems
Spies Hecker
Rigid Substrates (Steel and Aluminum)
Clearcoat • Permacron
®
MS Vario Clear Coat 8000
Basecoat * Permacron
®
Basecoat Series 293/295
Surfacer Permacron
®
Vario Surfacer 8590
Anti-Corrosion Primer # Priomat
®
1:1 Primer 3688
*Important: Hardener must be added to Permacron Basecoat Series 293-295
per technical recommendations.
# Can be used direct to aluminum.
• VOC Regulated - National Rule
2-37
2. Approved Paint Systems
Spies Hecker − Rigid Substrates (Cont’d)
Clearcoat • Permasolid
®
HS Clear Coat 8030
Basecoat * Permacron
®
Basecoat Series 293/295
Surfacer Permacron
®
Vario Surfacer 8590
Anti-Corrosion Primer # Priomat
®
1:1 Primer 3688
Clearcoat ••• Permacron
®
2.1 Clear Coat 8095
Basecoat * Permacron
®
Basecoat Series 293/295
Surfacer Permacron
®
2.1 Surfacer 5155
Anti-Corrosion Primer # Priomat
®
Wash Primer 4075
Clearcoat ••• Permacron
®
2.1 Clear Coat 8095
Basecoat * Permahyd
®
Basecoat Series 280/285
Surfacer Permacron
®
2.1 Surfacer 5155
Anti-Corrosion Primer # Priomat
®
Wash Primer 4075
Clearcoat • Permacron
®
MS Vario Clear Coat 8000 plus
Permacron
®
Elastic Additive 9050
(High Gloss, Non-Textured)
Permacron
®
MS Vario Clear Coat 8000 plus
Permacron
®
Elastic Additive 9050 plus
Permasolid
®
Texture Additive TA 101
Coarse (Textured)
Basecoat * Permacron
®
Basecoat Series 293/295
Surfacer Permacron
®
Vario Surfacer 8590
Anti-Chip Primer Permanal
®
Stone Chip Protector 7100
Primer Permacron
®
Vario Surfacer 8590 Gray plus
Permacron
®
Elastic Additive 9050
*Important: Hardener must be added to Permacron Basecoat Series 293-295
per technical recommendations.
# Can be used direct to aluminum.
• VOC Regulated - National Rule
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-38
2. Approved Paint Systems
Spies Hecker – Flexible Substrates
Clearcoat ••• Permacron
®
MS Vario Clear Coat 8000
Flexible Additive Permasolid
®
Elastic Additive 9050
(for surfacer and clearcoat)
Basecoat * Permacron
®
Basecoat Series 293/295
Surfacer Priomat
®
Vario Surfacer 8590
Primer Priomat
®
Elastic Primer 3304 Transparent
Clearcoat • Permacron
®
MS Vario Clear Coat 8000 plus
Permacron
®
Elastic Additive 9050
(High Gloss, Non-Textured)
Permacron
®
MS Vario Clear Coat 8000 plus
Permacron
®
Elastic Additive 9050 plus
Permasolid
®
Texture Additive TA 101
Coarse (Textured)
Basecoat * Permacron
®
Basecoat Series 293/295
Surfacer Permacron
®
Vario Surfacer 8590
Anti-Chip Primer Permanal
®
Stone Chip Protector 7100
Primer Permacron
®
Vario Surfacer 8590 Gray plus
Permacron
®
Elastic Additive 9050
Adhesion Promoter Priomat
®
Elastic Primer 3304
*Important: Hardener must be added to Permacron Basecoat Series 293-295
per technical recommendations.
• VOC Regulated - National Rule
••• VOC Regulated - National Rule, Rule 45 and Rule 1151
2-39
NOTES
2-40
GM Approved
Refinish Materials
GM Approved
Refinish Materials
GENERAL MOTORS CORPORATION
OCTOBER 2003
PRINTED IN USA
GM4901M-D-2004
2k4PaintCov.ai
9/05/03
4 color process
