V1.2 PiHPSDR Controller Users Guide Pi HPSDR
User Manual:
Open the PDF directly: View PDF
Page Count: 107 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- 1. Controller connection requirements 5
- 2. Front panel controls 7
- 3. Front Panel Display 8
- 4. Side panel connections 9
- 5. Quick Start Instructions 10
- 6. Discovery Menu 11
- 7. Main Menu 13
- 8. On-Screen Controls and toolbar Buttons 38
- 9. User assignable Actions for Encoders E1, E2, and E3 58
- 10. Individual Slider displays 59
- 11. Tuning 63
- 12. TUNE/SWR/FWD Power 64
- 13. Appendix 13. Appendix 65
- 14. Reference materials 69
- 15. Steve Wilson KA6S special addition for Fldigi 71
- 16. Supported CAT Commands (TS-2000 Compatible) 83
- 17. Supported CAT Commands (ZZ Extension commands) 88
- 18. Apache Support 97
- 19. Apache Service and Repair 97
- 1. Controller connection requirements
- Network LAN Connection
- Controller Hardware requirements
- Controller software requirements:
- 2. Front panel controls
- Default assignments of switches and rotary encoders
- 3. Front Panel Display
- 4. Side panel connections
- 5. Quick Start Instructions
- Hardware Setup
- Software Setup
- 6. Discovery Menu
- Discover Ethernet Connections to RPi
- Pihpsdr program START button
- 7. Main Menu
- Menu → Exit
- Menu → Hide
- E1, E2, E3 Click-Set Assignments
- Menu → Radio
- Menu → Receive (individual receiver settings)
- RaspberryPi (Audio Device Settings)
- Menu → TX with USB Input Source
- Menu → PA Gain by Band
- Menu → CW
- Menu → ANT
- Menu → DSP
- Menu → OC Open Collector Aux I/O connectors
- Menu → FreeDV
- Menu → Display
- Menu → Display (continued)
- Menu → XVTR
- Menu → Equalizers
- Menu → Step
- Menu → Meter – now includes new Analog S-Meter
- Menu → VOX
- Menu → FFT
- Menu → About
- 8. On-Screen Controls and toolbar Buttons
- Touch Direct Frequency Entry
- Toolbar – Function button
- There are eight (8) switches on the pihpsdr Controller.
- The functions are arranged in four groups.
- Switches S1 through S6 change function as you push the FN key
- Toolbar – Function menu selections
- Four Function menus – select with Function button or front panel FN switch
- Function Group 1
- Toolbar → MOX
- Toolbar → BAND VFO-A
- Toolbar → Band Stack for VFO-A selected
- Toolbar → Band Stack for VFO-B selected
- Toolbar → Mode VFO-A
- Toolbar → Mode VFO-B
- Toolbar → Filter VFO-A
- Toolbar → Filter VFO-B
- Toolbar → NOISE VFO-A
- Toolbar → NOISE VFO-B
- Toolbar → AGC VFO-A
- Toolbar → AGC VFO-B
- Toolbar → Function button
- Four Function Toolbar Groups → Menu
- Toolbar → VFO Lock
- Toolbar → CTUN – Click Tuning
- Toolbar → A>B, A<B, A<>B
- Toolbar → SPLIT
- Toolbar → FREQ
- Toolbar → MEM
- Toolbar → RIT – Receiver Incremental Tuning
- Tapping the RIT OFF/ON enables or disables Receiver Incremental Tuning
- Tapping on the RIT+ (plus) or RIT- (minus) button will
- Tapping RIT CL = RIT CLEAR
- Note: RIT offset shown in YELLOW TEXT above VFO-A
- Toolbar → TUNE
- 9. User assignable Actions for Encoders E1, E2, and E3
- 10. Individual Slider displays
- AGC Gain slider is shown when DISPLAY → show sliders is unchecked
- Receive Attenuation slider is shown when DISPLAY → show sliders is unchecked
- MIC Gain slider is shown when DISPLAY → show sliders is unchecked
- PA Drive slider is shown when DISPLAY → show sliders is unchecked
- Squelch slider is shown when DISPLAY → show sliders is unchecked
- MIC Compression is shown when DISPLAY → show sliders is unchecked
- 11. Tuning
- VFO Encoder
- Touch Screen
- Mouse
- 12. TUNE/SWR/FWD Power
- 13. Appendix 13. Appendix
- Encoders and Switches
- Switch or Encoder
- GPIO pin Assignments (RaspberryPi
- 14. Reference materials
- GØORX
- pihpsdr latest production version
- 15. Steve Wilson KA6S special addition for Fldigi
- ping a Serial Port to TCP/IP port in Linux
- Example: Set up GRIG to talk to PiHPSDR
- Example: Connect FLDIGI to PiHPSDR
- Also – check the PTT via CAT button in the lower left corner.
- Now Choose Config/Setup/TCPIP
- Setting up rigctld
- Multi-Client Support
- Running applications with the latest version of Hamlib
- Using CAT through a Serial Port
- KA6S Summary
- 16. Supported CAT Commands (TS-2000 Compatible)
- 5. Quick Start Instructions
- 4. Side panel connections