PN512 Datasheet. Www.s Manuals.com. Nxp

User Manual: Datasheets PN5120A0HN/C1, PN5120A0HN/C2, PN5120A0HN1/C1, PN5120A0HN1/C2, PN512AA0HN1/C2, PN512AA0HN1/C2BI.

Open the PDF directly: View PDF .
Page Count: 133 [warning: Documents this large are best viewed by clicking the View PDF Link!]

Scroll down to view the document on your mobile browser.

1. Introduction
- 1.1 Different available versions
2. General description
3. Features and benefits
4. Quick reference data
5. Ordering information
6. Block diagram
7. Pinning information
- 7.1 Pinning
- 7.2 Pin description
8. Functional description
- 8.1 ISO/IEC 14443 A/MIFARE functionality
- 8.2 ISO/IEC 14443 B functionality
- 8.3 FeliCa reader/writer functionality
  - 8.3.1 FeliCa framing and coding
- 8.4 NFCIP-1 mode
9. PN512 register SET
- 9.1 PN512 registers overview
  - 9.1.1 Register bit behavior
- 9.2 Register description
10. Digital interfaces
- 10.1 Automatic microcontroller interface detection
- 10.2 Serial Peripheral Interface
- 10.3 UART interface
- 10.4 I2C Bus Interface
11. 8-bit parallel interface
- 11.1 Overview of supported host controller interfaces
- 11.2 Separated Read/Write strobe
- 11.3 Common Read/Write strobe
12. Analog interface and contactless UART
- 12.1 General
- 12.2 TX driver
- 12.3 RF level detector
- 12.4 Data mode detector
- 12.5 Serial data switch
- 12.6 S2C interface support
  - 12.6.1 Signal shape for Felica S2C interface support
  - 12.6.2 Waveform shape for ISO/IEC 14443A and MIFARE S2C support
- 12.7 Hardware support for FeliCa and NFC polling
13. FIFO buffer
- 13.1 Accessing the FIFO buffer
- 13.2 Controlling the FIFO buffer
- 13.3 FIFO buffer status information
14. Interrupt request system
- 14.1 Interrupt sources overview
15. Timer unit
16. Power reduction modes
- 16.1 Hard power-down
- 16.2 Soft power-down mode
- 16.3 Transmitter power-down mode
17. Oscillator circuitry
18. Reset and oscillator start-up time
- 18.1 Reset timing requirements
- 18.2 Oscillator start-up time
19. PN512 command set
- 19.1 General description
- 19.2 General behavior
- 19.3 PN512 command overview
  - 19.3.1 PN512 command descriptions
20. Testsignals
- 20.1 Selftest
- 20.2 Testbus
- 20.3 Testsignals at pin AUX
- 20.4 PRBS
21. Errata sheet
22. Application design-in information
23. Limiting values
24. Recommended operating conditions
25. Thermal characteristics
26. Characteristics
- 26.1 Timing characteristics
- 26.2 8-bit parallel interface timing
  - 26.2.1 AC symbols
  - 26.2.2 AC operating specification
    - 26.2.2.1 Bus timing for separated Read/Write strobe
    - 26.2.2.2 Bus timing for common Read/Write strobe
27. Package information
28. Package outline
29. Abbreviations
30. Glossary
31. References
32. Revision history
33. Legal information
- 33.1 Data sheet status
- 33.2 Definitions
- 33.3 Disclaimers
- 33.4 Licenses
- 33.5 Trademarks
34. Contact information
35. Tables
36. Figures
37. Contents

Navigation menu