DCM M1 Sony_DCM M1_service_manual Sony Service Manual

User Manual: sony_DCM-M1_service_manual

Open the PDF directly: View PDF PDF.
Page Count: 198

DownloadDCM-M1 Sony_DCM-M1_service_manual Sony Service Manual
Open PDF In BrowserView PDF
DCM-M1
SERVICE MANUAL

US Model
Canadian Model
E Model

Ver 1.3 2000. 08
With SUPPLEMENT-1
(9-927-635-81)
With SUPPLEMENT-2
(9-927-635-82)
With SUPPLEMENT-3
(9-927-635-83)

Lens
Section

Model Name Using Similar Mechanism
Mechanism Type

NEW
CT-DCMM1-164

MD
Section

Model Name Using Similar Mechanism

NEW

Mechanism Type

MT-DCMM1-163

SPECIFICATIONS

– Continued on next page –

MINIDISC AV RECORDER
MICROFILM

SAFETY-RELATED COMPONENT WARNING!!

ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder
splashes and bridges.

4. Look for parts which, though functioning, show obvious signs
of deterioration. Point them out to the customer and recommend their replacement.

2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.

5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing

3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them
out to the customer and recommend their replacement.

• Keep the temperature of the soldering iron around 270 ˚C
during repairing.
• Do not touch the soldering iron on the same conductor of
the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.

–2–

TABLE OF CONTENTS
Section

1.

Title

Page

SERVICE NOTE ................................................

4

Section

Title

4.

PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS

4-1.
4-2.

4-3.

Frame Schematic Diagram ..........................................
Printed Wiring Boards and Schematic Diagrams .......
VC-216 Printed Wiring Board ......................................
VC-216 (LENS MOTOR DRIVE, CCD IMAGER)
Schematic Diagram .....................................................
VC-216 (CAMERA SIGNAL PROCESS)
Schematic Diagram .....................................................
MAIN Printed Wiring Board .........................................
MAIN (AUDIO/VIDEO DATA CONTROL)
Schematic Diagram .....................................................
MAIN (MPEG ENCODER/DECODER)
Schematic Diagram .....................................................
MAIN (RF AMP/DRIVE) Schematic Diagram .............
MAIN (DIGITAL SIGNAL PROCESSOR)
Schematic Diagram .....................................................
MAIN (SYSTEM CONTROL) Schematic Diagram .....
MAIN (VIDEO) Schematic Diagram ............................
MAIN (AUDIO) Schematic Diagram ............................
MAIN (SWITCHING REGULATOR)
Schematic Diagram .....................................................
MAIN CONTROL SWITCH UNIT, ZOOM SWITCH
UNIT Schematic Diagram ...........................................
UPPER CONTROL SW SUB ASSY,
REMOCON RAY-CATCHER BLOCK UNIT,
LCD DETECTION SW FLEXIBLE Board
Schematic Diagram .....................................................
CLV Printed Wiring Board ...........................................
CLV Schematic Diagram .............................................
REC Printed Wiring Board and
Schematic Diagram .....................................................
VF Printed Wiring Board .............................................
VF Schematic Diagram ...............................................
BL Printed Wiring Board .............................................
BL Schematic Diagram ...............................................
LCD Printed Wiring Board ...........................................
LCD Schematic Diagram .............................................
ETHER Printed Wiring Board ......................................
ETHER Schematic Diagram ........................................
JACK Schematic Diagram ...........................................
JACK Printed Wiring Board .........................................
POWER Printed Wiring Board ....................................
POWER Schematic Diagram ......................................
Waveforms ...................................................................

5.

EXPLODED VIEWS

5-1.
5-2.
5-3.
5-4.
5-5.
5-6.
5-7.
5-8.

Main Section ................................................................
Cabinet (R) Section .....................................................
Microphone Block Section ..........................................
Cabinet (L) Section .....................................................
LCD Block Section ......................................................
EVF Block Section .......................................................
Lens Block Section (CT-DCMM1-164) ........................
Mechanism Deck Section-1
(MT-DCMM1-163) ........................................................
Mechanism Deck Section-2
(MT-DCMM1-163) ........................................................

Page

GENERAL

Getting Started ......................................................................
Recording – Basics ...............................................................
Playback – Basics .................................................................
Advanced Recording Operations ..........................................
Advanced Playback Operations ............................................
Editing ...................................................................................
Drawing/Effect .......................................................................
Customing Your Camcorder ..................................................
Using with Other Equipment .................................................
Additional Information ............................................................
Quick Reference ....................................................................

2.

DISASSEMBLY

2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
2-8.
2-9.
2-10.
2-11.
2-12.
2-13.
2-14.
2-15.
2-16.
2-17.
2-18.
2-19.
2-20.
2-21.
2-22.
2-23.
2-24.
2-25.
2-26.
2-27.
2-28.
2-29.

Main Control Switch Unit .............................................
Cabinet (R) Section .....................................................
Zoom Switch Unit ........................................................
Power Board ................................................................
Ether Board .................................................................
Jack Board ...................................................................
Remote Terminal Unit ..................................................
Battery Case Assembly ...............................................
Microphone Block ........................................................
Main Board ..................................................................
Lens Block (CT-DCMM1-164) .....................................
Hinge Cover .................................................................
LCD Block ....................................................................
LCD Cabinet Assembly (U) .........................................
LCD Board ...................................................................
Fluorescent Tube .........................................................
Touch Panel, LCD Module (LCD4301) .......................
EVF Block ....................................................................
VF Board .....................................................................
VF Lens Assembly ......................................................
BL Board ......................................................................
Upper Panel Assembly ................................................
Mechanism Deck (MT-DCMM1-163) ...........................
CLV Board ...................................................................
Stepper Block Assembly (M5811) ...............................
Holder Assembly .........................................................
Service Position ...........................................................
Circuit Boards Location ...............................................
Flexible Boards Location .............................................

3.

BLOCK DIAGRAMS

3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
3-10.
3-11.
3-12.
3-13.
3-14.
3-15.
3-16.

Overall Block Diagram .................................................
Camera Signal Process Block Diagram ......................
Camera Control Block Diagram ..................................
A/V Data Control, Video Out Block Diagram ..............
MPEG Encode Block Diagram ....................................
MD Signal Process Block Diagram .............................
MD Servo Block Diagram ............................................
System Control Block Diagram ...................................
Audio Block Diagram ...................................................
LCD Block Diagram .....................................................
EVF Block Diagram .....................................................
Mode Control Block Diagram ......................................
Ether Interface Block Diagram ....................................
Power 1 Block Diagram ...............................................
Power 2 Block Diagram ...............................................
Power 3 Block Diagram ...............................................

1-1
1-5
1-7
1-8
1-11
1-14
1-19
1-21
1-23
1-26
1-28

2-3
2-3
2-3
2-4
2-4
2-4
2-5
2-5
2-5
2-6
2-6
2-6
2-7
2-7
2-7
2-8
2-8
2-8
2-9
2-9
2-9
2-9
2-10
2-10
2-11
2-11
2-12
2-14
2-16

3-1
3-3
3-5
3-7
3-9
3-11
3-13
3-15
3-17
3-19
3-21
3-23
3-25
3-27
3-29
3-31

5-9.

6.

4-5
4-9
4-9
4-13
4-17
4-21
4-29
4-33
4-39
4-43
4-48
4-53
4-56
4-59
4-62

4-65
4-68
4-75
4-79
4-83
4-87
4-93
4-97
4-101
4-106
4-109
4-116
4-119
4-121
4-125
4-130
4-133

5-1
5-2
5-3
5-4
5-5
5-6
5-7
5-8
5-9

ELECTRICAL PARTS LIST ............................. 6-1

* The color reproduction frame is shown after the page
of ELECTRICAL PARTS LIST.

–3–

SERVICE NOTE
• NOTE FOR REPAIR

When remove a connector, don’t pull at wire of connector.
Be in danger of the snapping of a wire.

Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.

When installing a connector, don’t press down at wire of connector.
Be in danger of the snapping of a wire.

Cut and remove the part of gilt
which comes off at the point.
(Take care that there are some
pieces of gilt left inside)

• When repairing this device with the power on, if you remove
the MAIN board or open the upper panel assy, this device stops
working.
In this case, you can work without the device stopping by fastening the hook of the open/close detect switch (S8003) on the
MAIN Board with tape.

S8003

–4–

DCM-M1
SECTION 1
GENERAL

1-1

This section is extracted from instruction manual. (3-866-152-11)

1-2

1-3

1-4

1-5

1-6

1-7

1-8

1-9

1-10

1-11

1-12

1-13

1-14

1-15

1-16

1-17

1-18

1-19

1-20

1-21

1-22

1-23

1-24

1-25

1-26

1-27

1-28

1-29

1-30E
1-30

DCM-M1
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.

DCM-M1

Main Control Switch Unit
(Page 2-3)

Cabinet (R) Section
(Page 2-3)

Power Board
(Page 2-4)

Jack Board
(Page 2-4)

Zoom Switch Unit
(Page 2-3)

Ether Board
(Page 2-4)

Remote Terminal Unit
(Page 2-5)

Microphone Unit
(Page 2-5)

Main Board
(Page 2-6)

Upper Panel Assembly
(Page 2-9)

Battery Case Assembly
(Page 2-5)

Mechanism Deck (MT-DCMM1-163)
(Page 2-10)

CLV Board
(Page 2-10)

Holder Assembly
(Page 2-11)

Stepper Block Assembly (M5811)
(Page 2-11)

EVF Block
(Page 2-8)

VF Board
(Page 2-9)

VF Lens Assembly
(Page 2-9)

BL Board
(Page 2-9)

Lens Block (CT-DCMM1-164)
(Page 2-6)

Hinge Cover
(Page 2-6)

LCD Block
(Page 2-7)

LCD Cabinet Assembly (U)
(Page 2-7)

LCD Board
(Page 2-7)

Fluorescent Tube
(Page 2-8)

Touch Panel, LCD Module (LCD4301)
(Page 2-8)

2-1

PAPER BOX FOR SCREW
We suggest to make a photo copy of this page before removing the set,
put cellophane tape (adhesive tape) in each dotted-line frame for each screw.
You can replace these screws without any mistakes after this preparation.
(If you use OHP sheet or something similar, you can use it repeatedly.)
unit: mm
S1

S2

S3

4.5

3

S5

S6

S7

3.5

S10

2

S11

S14

4

S8

5

2.5

S13

4

4

4.5

S9

S4

3

S12

2

5

S15

1.6

S16

1.3

2-2

2

Note: Follow the disassembly procedure in the numerical order given.

2-1. MAIN CONTROL SWITCH UNIT

2-3. ZOOM SWITCH UNIT

3 Two screws (S1)
(M1.7 × 3)
5 Two screws (S3)
(M1.7 × 4)

2 Zoom switch unit

6 Main control switch unit

4 Screw (S2)
(M1.7 × 4.5)

1 Screw (S6)
(M1.7)

8 Flexible board
(zoom switch unit)

2 Screw (S1)
(M1.7 × 3)

7 Translation
flexible board

1 Open the LCD panel.

2-2. CABINET (R) SECTION
0 Flexible board
1 Two screws (S4)
(power board)
(K2 × 4)
2 Bracket
9 Flexible board (CN9101)
(shoe)
(ether board)
6 Screw (S3)
(CN8007)
(M1.7 × 4)
5 Screw (S1)
7 Cabinet (R)
(M1.7 × 3)
section

S4

S1

3

4

S5

S2

4.5

8 Translation
flexible (jack)
board (CN3002)
3 Screw (S5)
(M2.0 × 4.5)

S6

S3

4

4 Screw (S1)
(M1.7 × 3)

2-3

4.5

3.5

2-4. POWER BOARD

2-6. JACK BOARD

1 Open the jack cover.
3 Flexible board
(remote terminal unit)
(CN8004)
3 Earth lug

2 Two screws (S7)
(M1.7 × 5)

5 Remove the JACK board
in the direction of the arrow.

1 Connector
5 POWER board

4 Two screws (S8)
(M1.7)
2 Translation flexible
(jack) board
(CN3003)

4 Two screws (S8)
(M1.7)

2-5. ETHER BOARD
S7

5

3 Insulating
sheet
1 Screw (S7)
(M1.7 × 5)
S8

5 Two earth lugs
6 ETHER board

2 Bracket
(ether board)
4 Screw (S7)
(M1.7 × 5)

2-4

3

2-7. REMOTE TERMINAL UNIT

ET

HE

2-9. MICROPHONE BLOCK

1 Connector
(CN3001)

R

5 Microphone block

2 Remove the remote
terminal unit in the
direction of the arrow.

3 Screw (S8)
(M1.7)

1 Screw (S8)
(M1.7)

4 Lug

2 Flexible board
(remocon ray-catcher block unit)
(CN8003)

2-8. BATTERY CASE ASSEMBLY

S3

1 Two screws (S3)
(M1.7 × 4)

4

S8

2 Screw (S3)
(M1.7 × 4)

3

3 Screw (S3)
(M1.7 × 4)
4 Battery case assembly

2-5

2-10. MAIN BOARD

3 VF flexible board
(CN4511)

2-12. HINGE COVER
2 Flexible board
(upper control switch unit)
(CN8002)
1 Flexible board
(VC-216 board)
(CN8101)

6 Two screws (S10)
(M1.7 × 2.5)

9 Hinge cover
(rear)

7 LCD detection sw
flexible board
(CN8006)

qa MAIN board

7 Blind plate
assembly

0 Three screws
(S9)
(M1.4 × 2)

8 Screw (S1)
(M1.7 × 3)

4 Claw

2 Two screws (S1)
(M1.7 × 3)

3 Two claws
5 Hinge cover
(front)

4 Flexible board
(OP block)
(CN5011)
9 Screw (S8)
(M1.7)
8 Screw (S7)
(M1.7 × 5)

qs Connector
(gray)
(CN4313)

6 Connector
(yellow)
(CN4312)

5 Flexible board
(CLV board)
(CN5002)

1 Open the LCD panel
and turn it 90°.

2-11. LENS BLOCK
(CT-DCMM1-164)

S1

3Lens block (CT-DCMM1-164)

S9

3

2

2 Screw (S1)
(M1.7 × 3)

S7

S10

5

S8
1 Acostic isolation (S)
material

3

2-6

2.5

2-13. LCD BLOCK

2-15. LCD BOARD
8 Flexible board
(fluorescent tube)
(CN4307)
7 Flexible board
(touch panel)
(CN4301)

4 Boss

2 Screw (S11)
(PS2 × 5)

6 Flexible board
(LCD)
(CN4306)

qa LCD board

5 Boss
9 Screw (S8)
(M1.7)

6 Remove the LCD block
in the direction of the arrow.
3 Screw (S11)
(PS2 × 5)
LCD panel

Hinge assembly

0 claw

1 Screw (S10)
(M1.7 × 2.5)

5 Two connectors
(CN4302, 4303)
3 Claw

2 Two claws

1 Set the LCD panel and
hinge assembly to a state
of the figure.

4 LCD frame

S1

2-14. LCD CABINET ASSEMBLY (U)

S11

3

1 Turn the hinge assembly.

S8

A

3

2 Two screws (S1)
(M1.7 × 3)

B

S10

3 Remove the LCD cabinet assembly (U)
in the direction of the arrows A-B.

2.5

2-7

5

2-16. FLUORESCENT TUBE

2-18. EVF BLOCK
1 Screw (S3)
(M1.7 × 4)

2 EVF block

1 Claw
2 Fluorescent tube

2-17. TOUCH PANEL, LCD MODULE (LCD4301)

1 Two screws (S10)
(M1.7 × 2.5)

S3

2 Claw
4 Hinge assembly

4

S10

3 Claw

5 Claw

2.5

6 Touch panel,
LCD module (LCD4301)

2-8

2-19. VF BOARD

2-21. BL BOARD

1 Flexible board
(LCX024AK-5)
(CN4702)

4 BL board

4 Claw

2 Two claws
2 Claw

7 VF board

6 Two claws

3 Two claws

3 Claw
5 Claw

2-22. UPPER PANEL ASSEMBLY

1 VF/LCD Flexible board
(CN4601)

2-20. VF LENS ASSEMBLY

3 EVF cabinet (upper)

5 Upper panel assembly
2 Screw
(S12)
(M1.4 × 2)

4 VF lens
assembly
Shaft

Visibility adjustment
arm
1 Set on eject position.
4 Two screws (S12)
(M1.4 × 2)

3 Screw (S12)
(M1.4 × 2)

2 Two screws (S7)
(M1.7 × 5)
1 Two screws (S7)
(M1.7 × 5)

S12

S7

Note : When installing VF lens assembly,
move the visibility adjustment knob
in the direction of the arrow and
connect shaft of VF lens assembly
with visibility adjustment arm.

5

Visibility adjustment knob

2-9

2

2-23. MECHANISM DECK
(MT-DCMM1-163)
2 Two screws (S13)
(damper)

5 Two dampers (MD)
6 Damper (MD)
9 Hold the part maked A in the
figure trying not to touch either
over write head or OP.
Pulling the mechanism deck
(MT-DCMM1-163) toward you,
pull out it to the disc slot side.
3 Two screws (S13)
(damper)

8 Claw
A

4 Damper (MD)
7 Claw

1 Rotate the worm gear in the direction
of the arrow A and move the torsion
spring (limitter) in the direction of the arrow B.
OK

NG

NG
Worm gear

A
B

Note : When installing damper (MD),
put it together in the figure.

Torsion spring (limitter)

2-24. CLV BOARD
2 Motor flexible board
(CN5801)

S13

4 Two screws (S14)
(M1.4)
4

5 CLV board
1 Flexible board
(CN5902)

S14

1.6

3 Remove the solders of the spindle
motor flexible board.

2-10

2-25. STEPPER BLOCK ASSEMBLY (M5811)

5 Stepper block assembly
(M5811)

S15

2 Motor flexible board

3 Screw (S15)
(M1.4)

1.3

1 Remove solders of
motor flexible board.

S16

2

4 Claw

2-26. HOLDER ASSEMBLY

3 Screw (S16)
(M1.4)
4 Holder guide
1 Flexible board (CLV board)
5 Shaft
(CN5902)
6 Shaft

2 Flexible board
(over write head)
(CN5901)

Lever (rack)
Holder assembly

Note : When installing holder
assembly, connect lever
(cam) with lever (rack).

Flexible board
(over write head)

Note : When connecting flexible board
(over write head), put it together
in the figure.

7 Holder assembly

2-11

2-27. SERVICE POSITION
Preparation: Refer to previous section “DISASSEMBLY”, and connect as shown in the figure after each part has been removed.
AC adaptor
(AC-VQ800)

MAIN BOARD, CLV BOARD

AC in
Zoom switch unit
Battry case assembly
Main control switch unit

MAIN board
Lens block
CLV board

LCD block

Note : Put an insulating sheet
between MAIN board and
POWER board.

POWER board
Cabinet (L) block
Stand

LCD BOARD

VF BOARD

AC adaptor
(AC-VQ800)
AC in

AC adaptor
(AC-VQ800)

Main control switch unit
AC in

POWER board

MAIN board
VF board

LCD board

LCD block
Stand

EVF block
Stand

2-12

MEMO

2-13

2-28. CIRCUIT BOARDS LOCATION

BL board
(EVF BACK LIGHT)

VF board
(EVF)

POWER board
(DC/DC CONVERTER)

MAIN board
AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER,
RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR,
SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR

2-14

ETHER board
(ETHER INTERFACE)

JACK board
(AV IN/OUT)
LCD board
(LCD)

VC-216 board
LENS MOTOR DRIVE,
CCD IMAGER,
CAMERA SIGNAL PROCESS

REC board
OVER WRITE
HEAD DRIVE

CLV board
(MD MOTOR DRIVE)

2-15

2-29. FLEXIBLE BOARDS LOCATION

3 VF/LCD flexible board

Upper control switch unit

Remote terminal unit

1 Translation flexible board
Remocon ray-catcher
block unit

Fluorescent tube

LCD module (LCD4701)

Lens device

Zoom switch unit

4 LCD detection sw
flexible board
LCD module (LCD4301)
Touch panel

2-16

5 Motor flexible board
VF flexible board

2 Translation flexible
(jack) board

Over write head (HR5901)

Spindle motor
(M5821)
OP block

unit: mm

1 Translation flexible board

2 Translation flexible (jack) board

3 VF/LCD flexible board

10

5

15

38

4 LCD detection sw flexible board

5 Motor flexible board

10
5
11

22

3
26

3

4
9

3

5

6
5

10

2-17
2-17E

DCM-M1
SECTION 3
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM
ZOOM LENS UNIT
IRIS METER
ZOOM LENS

VC-216 BOARD
CCD OUT

IC001
CCD
IMAGER

IC101

D0-D9
IC102
S/H,AGC,
A/D CONVERTER

TIMING
GENERATOR

Y0-Y7

CAMERA
Y/C
PROCESS

C0-C3

IC5403
MEC0-MEC7
IC8602

DDO

SYS MVP0-SYS MVP7

IC8601
MPEG2
ENCODER

CLV BOARD
(1/2)

1M FAST SDRAM

(SEE PAGE 4-75)

DDI

IC202

M

ZOOM MOTOR
DRIVE

IC5901

IC5102

V IN

16M EDO DRAM

FOCUS
SENSOR

MNT0
DADT

IC8701
MPEG2
VIDEO
PROCESSOR

IC5301

DETECTOR

IC5007

LASER
DIODE

SWITCH

IC5602

FOCUS
COIL
TRACKING
COIL

FOCUS/TRACKING
COIL DRIVE

DIGITAL
SERVO
SIGNAL
PROCESSOR

IC201

I,J

RF AMP
FOCUS/TRACKING
ERROR AMP

RFI

MD1 DIGITAL
SIGNAL
PROCESSOR

OPTICAL PICK-UP
BLOCK

IC5002

RF
MDTI

SERIAL BUS

IC8702 IC8703
ZOOM
SENSOR

RFO

MPEG2
RATE
CONTROL
&
SYSTEM
CONTROL

PARALLEL BUS

M902
FOCUS MOTOR

MVP0-MVP7

ENDT0-ENDT7

IRIS/
FOCUS/
ZOOM
CONTROL

OUT A/B

A/D CONVERTER
IC8501

FOCUS MOTOR
DRIVE

HR5901
OVER WRITE HEAD

HEAD SWITCH
D0-D7

64M SDRAM

(SEE PAGE 4-79)

HN-H/L,HP-H/L

MD2 DIGITAL
SIGNAL
PROCESSOR

SERIAL BUS

M903
ZOOM MOTOR

M

IC105

REC BOARD

IC5501

MAIN BOARD (SEE PAGE 4-29 to 59)

(SEE PAGE 4-13, 17)

SLED MOTOR
DRIVE
IC5601

IRIS DRIVE
HALL BIAS/
GAIN CONTROL

HALL
SENSOR

M

HEAD UP/DOWN
MOTOR DRIVE
SERIAL BUS

IC106
HALL AMP

IC103

IC8101

EEP ROM

AUDIO & VIDEO
DATA CONTROL

CAMERA
CONTROL

MF
BLOCK

M
M5801
SLED MOTOR

SERIAL BUS
IC5404

FG

DRIVE
CONTROL

CLV BOARD (2/2)

M5821
SPINDLE MOTOR

(SEE PAGE 4-75)

THERMAL
SENSOR
IC5405

SERIAL BUS

YAW
SE001 SENSOR

IC002

PITCH
SE201
SENSOR

SENSOR
AMP

IC8102 IC8103

IC5804 IC5805 IC5806 IC5808

NV-RAM

64M EDO DRAM

PHASE CONTROL
DETECT SWITCH

IC5406

SE5851

TEMPERATURE
SENSOR

REMOCON RAYCATCHER BLOCK UNIT

M5811
HEAD UP/DOWN
MOTOR

IC5851

IC1

SHOCK
SENSOR

SHOCK SENSOR AMP

REMOTE CONTROL
RECEIVER

(SEE PAGE 4-65)

IC8002 IC8003

UPPER CONTROL SW SUB ASSY,
LCD DETECTION SW,
FLEXIBLE BOARD

ACDI

FUNCTION KEY
&
JOG

(SEE PAGE 4-65)

POWER BOARD

IC8004

IC4502

1M EEPROM

EVR

TIMING GENERATOR
64M FLASH

+

PARALLEL BUS

2.3V
D2.85V
A2.85V
–20V
–6.5V
13V
12V
4.95V (CAMERA)
4.95V (ETHER)
4.95V (VIDEO)
4.95V (DRIVE)
D3.1V

BATTERY
TERMINAL

LCD DRIVER

LCD
PANEL

(SEE PAGE 4-97)
BACK LIGHT

IC8005

IC8001

SWITCHING
&
REGULATOR

R
B
G

IC4501

BL BOARD
IC4602

RESET

IC4601

SYSTEM CONTROL

SWITCHING
CONTROL

R-Y
B-Y
Y

IC8009

(SEE PAGE 4-130)

IC9001

VF BOARD (SEE PAGE 4-87)

R-Y
B-Y
Y
C

SERIAL BUS

(SEE PAGE 4-62)

ACDO

64M SDRAM

MAIN CONTROL SWITCH UNIT (1/2),
ZOOM SWITCH UNIT

IC8008

DRIVE PULSE GENERATOR

LCD BOARD (SEE PAGE 4-106)

REAL TIME
CLOCK

SERIAL BUS

SERIAL BUS

R-Y
B-Y
Y

R
B
G

IC4302
LCD DRIVER

LCD
PANEL

TOUCH
PANEL

IC4301
D/A CONVERTER
IC4303
TIMING GENERATOR

BACK LIGHT
IV4301
INVERTER UNIT

UNREG

BATT SIG

J11

JACK BOARD (2/2)

–

(SEE PAGE 4-119)

REMOTE TERMINAL
UNIT (SEE PAGE 4-119)

IC8027

ETHER BOARD (SEE PAGE 4-109)

ETHER
ADAPTER

LANC
DRIVER

IC8808
SRAM

IC8806

10BASE-T

SERIAL BUS

IC3009
ATRAC

ETHER
INTERFACE

Y

IC4002

IC4001

Y

Y

J4001

C

IC4004

IC4003

C

C

S. VIDEO

Y/C VIDEO
SIGNAL AMP

Y/C VIDEO
SIGNAL AMP

LINE R
LINE IN

SDTO

LINE L

LINE IN L/R

Y

ACDO

DIDT

SERIAL BUS

SDTI
ACDI
J3001
MIC R

MIC
PLUG IN POWER

JACK BOARD (1/2)
L/R IN2

(SEE PAGE 4-119)

MIC L

MIC IN L/R
IC3001

05
MIC2001
MIC1001

3-1

R CH
L CH

MIC R
MIC L

IC3004
AD/DA
CONVERTER

L/R OUT1
L/R OUT2

IC3007
HP/LINE
AMP

C

IC4005
COMPOSITE
VIDEO AMP

VIDEO

LINE-L
LINE-R

LINE OUT L/R

HP-R

HP OUT L/R

HP-L

L/R IN1
HP OUT L/R

J3002

MAIN CONTROL SWITCH UNIT (2/2)

IC3008

MIC AMP

J3003
AUDIO/VIDEO

(SEE PAGE 4-62)

SP AMP

3-2

SP+

SP3001
(SPEAKER)

REMOTE

DCM-M1

3-2. CAMERA SIGNAL PROCESS BLOCK DIAGRAM
VC-216 BOARD (1/2)
(SEE PAGE 4-13, 17)

CAMERA Y/C PROCESS
IC105 (1/2)
1 Vp-p
H

CDS, AGC, A/D CONVERTER
IC102

REC/PB

CLPOB 20

CCD IMAGER
IC001
26

BUFFER
Q001

CCD OUT 8

AGC

CDS

S/H

27

A/D
CONVERTER

D0
I
D9

50
I
YO 0 47
I
YO 7 45
I
42

78 CLPOB

2
I
11

89
I
80

AD 0
I
AD 9

V1 4

26 V1

V2 3

25 V2

V3 2

28 V3

XSHP 15

V4 1

31 V4

XSHD 16

TIMING

PGA CONT 2

21 22 16

33 VSHT

VCK (CL) 12

29

3 AGC CONT 2

30

2 AGC CONT 1

CAMERA
Y/C
PROCESS

CO 0 40
I
I
CO 3 37

16
I
19

HDO 51

7

VDO 52

6

ZV1 41
ID 48

3.28 Vp-p

AHD 44

18 MHz

AVD 45

REC/PB

18MHz

ZSG1
3.84 Vp-p

VGAT

18 MHz

ZV1

REC/PB

ID
TGHD

13.5MHz

21 H1
22 H2

TO SYSTEM CONTROL
(SEE PAGE 3-15)

SPCKO

73 PBLK

2.96 Vp-p

74 ZSG1
2V

71 VGAT

REC/PB

75 ZV1
72 ID
76 TGHD

3.04 Vp-p

2.88 Vp-p

Approx.
3.4 Vp-p

77 TGVD
13.5 MHz

V

H1 11

3

VCK 65

18 RG

H2 12

B

REC/PB

69 CHCK

TGVD

CK 7
RG 10

CAM VD

2.88 Vp-p

AGC THROUGH

VGAT 36

REC/PB

CAM HD

V

STBY

ZSG1 34
H

C0-C3

FLDO 53

MCKO 63
7 Vp-p

Y0-Y7

18 40

PBLK

SUB 13

PGA CONT 1

23 CLPDM

CLPDM 1

TO A/V DATA CONTROL,
VIDEO OUT
(SEE PAGE 3-7)

REC/PB

19 PBLK

PBLK 2

A

3.04 Vp-p

H
REC/PB

8
I
15

H

TIMING GENERATOR
IC101
7 Vp-p

CN101 (1/2)

OSCO 5

X101
36MHz

REC/PB

OSC ADJ
IC104

OSCI 4

H
REC/PB

REC/PB

6 FRQ

3.12 Vp-p

DSGAT 42

16.33 MHz

29

REC/PB

2.24 Vp-p

CAM VD

RST

SEN

SSI

SSK

SSO

REC/PB

2

CAM RST

CS CAM

CAM SO

CAM SCK

CAM SI

35 37 38 39 40

TO CAMERA CONTROL
(SEE PAGE 3-6)

CAM FLD

36 MHz

TO CAMERA
CONTROL
(SEE PAGE 3-6)

SIGNAL PATH
VIDEO SIGNAL
CHROMA

1

Y

Y/CHROMA

REC

05

3-3

3-4

CAM DD ON

DCM-M1

3-3. CAMERA CONTROL BLOCK DIAGRAM
VC-216 BOARD (2/2)
(SEE PAGE 4-13 to 17)
SENSOR AMP
IC002

SE001
YAW
SENSOR

2

4 Vref 1

4

8 LIA 1

ZOOM LENS
UNIT

CRST 19

7 C RESET

16 Vref 2

OUT 2 18

74 PITCH AD

4

12 LIA 2

CAMERA CONTROL
IC106

8

REC/PB

XTAL 40
EXTAL 41

X102
20MHz

CN101 (2/2)

MF VCC SWITCH
Q203

CN201
MF VCC

2

73 YAW AD

OUT 1 2

SE201
PITCH
SENSOR

1.22 Vp-p
20 MHz

HI SCK 62

20

HI SO 61

21

DATA TO HI

HI SI 60

22

DATA FROM HI

XCS CAM 59

23

XCS CAM

XRST CAM 38

24

XRST CAM

ZOOM SW AD 80

28

ZOOM SW AD

A2.85V (CAMERA)

C

TO SYSTEM CONTROL
(SEE PAGE 3-15)

D

TO MODE CONTROL
(SEE PAGE 3-24)

XHI SCK

17 MF LED
MF
BLOCK

THERMAL
SENSOR

MF A, MF B

TEMP OUT

10

30 MF A

9

22 MF B

85 LENS THERMAL A/D

22

2

IRIS DRIVE
IC201 (1/4)
IRIS
METER

DRIVE +

16

4.95V
(CAMERA)

STBY GCAM

3

AGC THROUGH

4

M

STBY
AGC THROUGH
CAM VD

VD 51
15

DRIVE
Q202

+
–

DRIVE –

8

CAM FLD

FLD 56

9
10

TO CAMERA SIGNAL
PROCESS
(SEE PAGE 3-4)

43 IRIS PWM

LPF

1

20

HALL +

H

–
+

BIAS +

1

XRST CAM

SOFT V 11

2

CAM SI 33

5
HALL GAIN CONTROL
IC201 (3/4)

18

HALL GAIN
CONTROL
Q204

–
+

BIAS –

14

6

+
–

7

HALL AD

EEPROM
IC103

72 HALL AD

12

16 LENS RST LED

XCS EEPROM 27

1

XCS

SCK

2

13

19 ZOOM RST SENSOR

XWEN EEPROM 28

6

RST

DI

3

20 FOCUS RST SENSOR

BUSY EEPROM 31

7

BUSY

DO

4

5

91 IRIS COM

LENS RST LED
ZOOM RST SENSOR

FOCUS
SENSOR

FC RST

IRIS

11 HALL REF

XSCK 26

12 HALL GAIN

FOCUS RST SENSOR
ZM RST

IRIS,
FOCUS/ZOOM
IC105 (2/2)

13 HALL OFFSET

A2.85V (CAMERA)
23

ZOOM
SENSOR

CAM SCK

CAM SCK 35

SENSOR VCC
SWITCH
Q201
SENSE VCC

CAM SI
CAM SO

CAM SO 34

HALL ANP
IC201 (4/4)

17

CAM RST

2

3

19

HALL –

CS CAM

CS CAM 98

HALL BIAS CONTROL
IC201 (2/4)

SI 27
EACH
BLOCK

94 SENS 1

6

SIO

SO 28
SYS V 29
XCLR 30

M903
ZOOM
MOTOR

ZM XA

M

ZM B

24

ZM A

ZM XB
M902
FOCUS
MOTOR

M

FC A
FC XA
FC B
FC XB

93 SENS 0

2

8 A3 ZA

4

22 B3 ZA

1

10 A4 ZB

3

20 B4 ZB

12

5 A1 FA

14

26 B1 FA

11

7 A2 FB

13

24 B2 FB

ZOOM
MOTOR
DRIVE
IC202 (1/2)

IN3 16

99 DIR1A

EN3 17

98 EN1

IN4 18

100 DIR1B

FOCUS/
ZOOM
MOTOR

EN4 19
FOCUS
MOTOR
DRIVE
IC202 (2/2)

IN1 12

96 DIR0A

EN1 13

95 EN0

IN2 14

97 DIR0B

EN2 15

05

3-5

3-6

TO CAMERA SIGNAL
PROCESS
(SEE PAGE 3-3)

DCM-M1
3-4. A/V DATA CONTROL, VIDEO OUT BLOCK DIAGRAM
MAIN BOARD (1/7)

JACK BOARD (1/4)

AUDIO & VIDEO DATA CONTROL
IC8101

(SEE PAGE 4-29, 48, 53, 59)

(SEE PAGE 4-119)
Y VIDEO SIGNAL AMP
IC4004

CN8101 (1/3)
8
ı
15

Y0 – Y7

A
TO CAMERA SIGNAL
PROCESS
(SEE PAGE 3-4)

C0 – C3

16
ı
19

CAM_VD
CAM_HD
SPCKO

92
ı
98
•
100

ADC0/YIN0
ı
ADC7/YIN7

89
•
91
•
101
•
109

C0/CIM0
ID/CIN1
ADC8/CIN2
ADC9/CIN3

CN3002
(1/4)

FL4002
BUFFER
Q4002

IO0 71

LPF

4

IN

OUT

4

2

IN

OUT 2
•
SAG 3

6

S_Y

CN3003
(1/4)

S

6

G

Y

J4001
S. VIDEO

STBY
1

STBY
1

C

2.32 Vp-p

REC/PB

C VIDEO SIGNAL AMP
IC4002

H
REC/PB

4
1
STBY

G
S

H

1.12 Vp-p

111 EXVD
110 EXHD
112 VCLK

6
7
3

Y VIDEO SIGNAL AMP
IC4003

S_JACK_DET

4

C VIDEO SIGNAL AMP
IC4001

1
STBY

FL4001
3.04 Vp-p

BUFFER
Q4001

IO1 72

BPF

4

OUT

IN

4

2

IN

OUT

2.88 Vp-p

188
195
194
192
190
191

ACLK
SYS_ACDO
SYS_ACDI
XABS
XARQ

BUFFER
Q4005

Y IN

LINE OUT L
OUT1, 2

H
REC/PB

IO3 84

BUFFER
Q4006

IO2 83

BUFFER
Q4007

4

C IN

1

VHD 66

REC/PB

7

VCC

SWITCH
Q4002, 4004

360 mVp-p
H

IC4006

VIDEO OUT
10
10
4_JACK_DET
12
12

6•
7

1.48 Vp-p

CN4313
(1/3)

H
REC/PB

12
11
10
3
4

IC4006

6

3

1

7

IC4009

6

3

IC4009

VVD 67

SA0 – SA11

WE

RAS

LCAS

UCAS

WE

RAS

DQ1
ı
DQ16

UCAS

13

14

37

38

13

14

TO MD SIGNAL
PROCESS
(SEE PAGE 3-12)
TO MD SIGNAL
PROCESS
(SEE PAGE 3-12)

SCLK_SYS
SO
SI
DDO
DDI
DSYNC
DCLK
512FS
MDTI
MLRCK

4

5

6

V

130
129
135
134
132
131

RAS
DWE
CAS0
CAS1
CAS2
CAS3

196
197
198
205
206
207
209
189
200
202

SCLK
SO
SI
DDO
DDI
DSYNC
DCLK
RCLK
MDTI
MLRCK

2 1D

37
ı
41
•
43
ı
45

MEC0 – MEC7

MVP0
ı
MVP7

54
•
52
ı
46

SYS_MVP0 – SYS_MVP7

BITO
BITI
HANDO
HANDI

32
33
34
36

FSY 210

2 –• 4
224 –• 227
– 233
229
DATA0
•
ı
235 – 240
DATA31 242 –• 248
•
250 – 256

X1Q 6
X1CK 3

C_OUT_OFF
S_OUT_OFF
S_JACK_DET
4_JACK_DET

SYS_BITO
SYS_BITI
HANDO
HANDI

7

ADDR1
ı
ADDR23

203 MBCK
128 PLL OUT

5 –• 8
10 –• 15
17 –• 23
25 –• 29
31

XRD
XWE3
XWE2
XWE1
XWE0
XWAIT
XINT

212 MCLK

TO MPEG ENCODE
(SEE PAGE 3-9)

FSY_INT
MCLK_BUFF

D0 – D31

8

D-FF
IC8104 (1/2)
MBCK

MEC0
ı
MEC7

REC/PB

38

CN4511
(1/2)

3.1 Vp-p

19 – 24 • 27 – 32

37

TO MD SERVO
(SEE PAGE 3-14)

REC/PB

A0
ı
A11

2 – 5 • 7 – 10 •
41 – 44 • 46 – 49

H

64M
EDO DRAM
IC8103

LCAS

DQ1
ı
DQ16

SD0 – SD15

SA0 – SA11

19 – 24 • 27 – 32

A0
ı
A11

2 – 5 • 7 – 10 •
41 – 44 • 46 – 49

174 –• 176 DRAMA0
178 –• 184
ı
186 • 187 DRAMA11

TO SYSTEM CONTROL
(SEE PAGE 3-16)

A0 – A23

FSY_INT
RD
DQMUU_ICIOWR
DQMUL_ICIORD
DQMLU_WE1
DQMLL_WE0
SYS_WAIT
SYSCHIP_INT

213
214
215
217
218
219
220
D-FF
IC8020 (1/2)

XCS 222

5 1Q
3 X1CK

1D 2

CPU_CS4_100

3.52 Vp-p

SIGNAL PATH

27 MHz
REC/PB

TRST 123
RST 211

D-FF
IC8104 (2/2)
9 2Q
11 X2CK

2D 12

VIDEO SIGNAL

MD SIGNAL
MD1

DEV_RESET

MD2

CHROMA

Y

Y/CHROMA

AUDIO
SIGNAL

REC
Approx.
3.4 Vp-p

PB

13.5 MHz
REC/PB

05

3-7

J3003 (1/2)
AUDIO/VIDEO
LINE OUT R

3.6 Vp-p

64M
EDO DRAM
IC8102

3

2

700 mVp-p

136 –• 140
142 –• 147
149 –• 153 DRAMD0
155 –• 158
ı
160 –• 163 DRAMD31
165 –• 169
171 – 173

DATA BUS

SD16 – SD31

ACLK
RCK4
ACDO
ACDI
XABS
XARQ

8

ADDRESS BUS

S_C

COMPOSITE VIDEO
SIGNAL AMP
IC4005

REC/PB

3

3

REC/PB

V

TO AUDIO
(SEE PAGE 3-18)

2

H

3-8

PANEL_Y
PANEL_R-Y
PANEL_B-Y
LCD_XHD
LCD_XVD

EVF_Y
25
EVF_R-Y
24
EVF_B-Y
26
EVF_XHD
27
EVF_XVD
23

E

TO LCD
(SEE PAGE 3-19)

F

TO EVF
(SEE PAGE 3-21)

DCM-M1

3-5. MPEG ENCODE BLOCK DIAGRAM

41 – 43 • 45 – 48
• 50 – 55
BA0, BA1,
AD0 – AD9

DR0 – DR31

17 18 19 68

59 58 57 84
MPEG2 RATE CONTRL
&
SYSTEM CONTROL
IC8501

XWE
CAS
RAS
SCLK

1 – 4 • 6 – 8 • 10 • 11 • 13 – 16 • 18 •
19 • 21 – 28 • 30 – 32 • 44 – 38 • 40

MPEG2 ENCODER
IC8601

64M SDRAM
IC8602

WE
CAS
PAS
CLK

l

A0

A12

22 – 27 •
60 – 66
BA0, BA1,
ADE0 – ADE9

l

2 • 4 • 5 • 7 • 8 • 10 • 11 • 13 • 31 • 33 • 34 • 36 • 37 • 39 • 40 • 42 •
45 • 47 • 48 • 50 • 51 • 53 • 54 • 56 • 74 • 76 • 77 • 79 • 80 • 82 • 83 • 85
DRE0 – DRE31

DQ0

(SEE PAGE 4-33, 59)

DQ31

MAIN BOARD (2/7)

137 • 138

127

•

140 – 143
MEC0 – MEC7

D0-D15

113 VE0 – VE7
l
120

•

DRAM INTERFACE

122

MOTION
ESTIMATION

FSY

MB DATA
PROCESSOR

94

TO A/V DATA CONTROL,
VIDEO OUT
(SEE PAGE 3-8)

l

99 VDI0 – VDI7
•
101
l

102
ADAPTIVE PREFILTER

MB DATA
INTERFACE

128 ENDT0 – ENDT7
l
135

136 D15
l

•

HOST INTERFACE

7

CLK

l

•

157

VIDEO
INTERFACE

l

111

134 D0
143

•

104 VDD0 – VDD7
SYS_MVP0 – SYS_MVP7 •
106

FSY_INT

850D0 – 850D15

155 • 156

•

175

850D0 – 850D15

150 – 153

103

MCLK_BUFF

l

•

145 – 148

A0 – A5 158
•
160

850A1 – 850A6

850A0 – 850A6

l

119 A0
l

l

125 A6

163
XRST
PLLI(FN)
XIMB
BS
XCS
XRD
XWR

ENCODE SEQUENCE
CONTROL

173
62
170
164
168
166
167

CHROMA POSTFILTER

4JACK_DET
S_JACK_DET
C_OUT_OFF
S_OUT_OFF

4
80
1
87
98
94
95
97

MEC_RESET
CLK_OUT
XIMB
BS
XCS1
XRD
XWR
XCS2

106
103
101
102

4JACK_DET
S_JACK_DET
C_OUT_OFF
S_OUT_OFF

ADA_REST
AT_REST
AT_EXEC
AT_STRO
AT_INSL
AT_MUTE
AT_REC
AT_ATRAC2
AT_LEVEL3
SP_BEEP
HP_BEEP
SP_NMUTE
AMUTE
SP_VDD
PWR_DWN
MIC_ATT
XWIND

19
20
47
48
49
50
51
52
53
7
8
88
89
90
91
110
111

ADA_REST
AT_REST
AT_EXEC
AT_STRO
AT_INSL
AT_MUTE
AT_REC
AT_ATRAC2
AT_LEVEL3
SP_BEEP
HP_BEEP
SP_NMUTE
AMUTE
SP_VDD
PWR_DWN
MIC_ATT
XWIND

MIC_JACK_DET
MIC_JACK_DET 104
HP_JACK_DET
HP_JACK_DET 105
W_JACK_DET
W_JACK_DET 107
CN8007
(1/3)
ETHER_RESET 23

11 X2CK

CLK

65
l

68
•

VOUT0 – VOUT7

DATA BUS

ADDRESS BUS

•

17 18 34 • 35

V_REC_LED
V_REC_LED 78
A_REC_LED
A_REC_LED 79

10

TO MODE CONTROL
(SEE PAGE 3-24)

DRV_RESET

11

TO MD SERVO
(SEE PAGE 3-14)

DEV_RESET
RATE_RTS

12

TO SYSTEM CONTROL
(SEE PAGE 3-15)

VA0 – VA9

DRV_RESET 22

63 61 62
XRESET 71
RATE_RTS 33
RXDO 40

XWE
RAS
CAS

ENCODER

•

LOCAL
DECODER

•

RX_SYS 43
TXDO 39
RST
TRST

VARIABLE LENGTH
CODING

VARIABLE LENGTH
DECODING

RIGHT
1
DOWN
2

RIGHT 58
DOWN 59

LCAS

WRITE
RAS
UCAS

l

A9

A0

VA0 – VA9

l

I/O1

VD16 – VD31

•

LCAS

I/O16

21 – 24 •
27 – 32

HOST INTERFACE

112

FSY

2 – 5 • 7 – 10 •
41 – 44 • 46 – 49

DRAM INTERFACE

POSTFILTER

•

11
1

RA0 – RA9

ENDT0 – ENDT7
MB DATA
INTERFACE

l

9

17 18 34 • 35

49 • 50 • 52 – 57
• 59 • 60

RD0 – RD31

12 – 14 • 16 – 19 • 21 – 24 •
26 – 36 • 38 – 43 • 45 – 48

VIDEO
INTERFACE

2

WRITE
RAS
UCAS

l

A9

VA0 – VA9

A0

l

VD0 – VD15

I/O1

I/O16

21 – 24 •
27 – 32

VD0 – VD31

ENDT0 – ENDT7

MVP0 – MVP7

MPEG2 VIDEO PROCESSOR
IC8701

2 – 5 • 7 – 10 •
41 – 44 • 46 – 49

XWR
XRD
XCS
A0 – A5

•

TX_SYS 40
RATE_CTS 6

•

118

RATE_TX
RATE_RX
RATE_CTS

92
91
90
84
l

89
D0 – D7

•

111

75
l

82

1.12 Vp-p
6.6 MHz
REC/PB

850A0 – 850A5
X1 64
X8501
6.6MHz

850D0 – 850D7
X2 63

BIT STREAM MANAGER

70

BITO
BITI

106 107

SYS_BITI
SYS_BITO
HANDO
HANDI

HANDO
HANDI

l

73

108 110

05

3-9

ETHER_RESET

G

TO ETHER
INTERFACE
(SEE PAGE 3-25)

H

TO LCD
(SEE PAGE 3-19)

CN4313
(2/3)

16M EDO DRAM
IC8703

REC/PB

32

5 MVP_RESEM

D-FF
IC8020(2/2)

3.52 Vp-p
27 MHz

16M EDO DRAM
IC8702

2D 12
2Q 9

TO AUDIO
(SEE PAGE 3-17)

9

3-10

DCM-M1

3-6. MD SIGNAL PROCESS BLOCK DIAGRAM

1 – 4 • 13 – 21 •
29 – 32

OE
WE

l

I/O1

l

A0

A16

(SEE PAGE 4-39, 43)

I/O8

1M FAST SRAM
IC5501

MAIN BOARD (3/7)

6 • 7 • 10 • 11 •
22 • 23 • 26 • 27

28 12

56 – 62 • 64 – 73 46 – 50 • 53 – 55

74 75

SRAM CS

CS 5

50

MHEN

47

48
MOFRO

CN5001
I
J

24
25

MOFRI
RFO

I
1
J
2

RF AMP

CLOCK
GENERATOR

LSRCK

Approx.
1.22 Vp-p
: MD1
Approx.
880 mVp-p
: MD2

12
CLK
21 VIN

SYNC
GENERATOR

37

A/D
CONVERTER
IC5102

L. P. F.
FL5101, Q5101

46

89

TO/FROM
ADIP

ADRF0
l
87 ADRF7
l
80

D0 1
l

SYNC
SELECTOR

ADCCK

l

D7 8

COMMAND

B

D

A

EQ

VC

ADDER/
SUBTRACTER

WBL
AMP

G&H

21

8
9

B.P.F.

PEAK
37
BOTM
36

SE

SLED ERROR
AMP

TE

TRACKING
ERROR AMP

B
C
D

27

4

23

5

22

6

26

7

A

AT
AMP

B.P.F

29

30

ADFG

ADIN

I-V
AMP

D

ABCD

ABCD
AMP

55
52
51

28

Approx.
324 mVp-p

26
200 ns
PB (MD1)

FS4

Approx.
360 mVp-p
100 ns
PB (MD2)

59
58
61
60
90

32

78

VC
RFI
ASYI
ASYO
FILI
PCO
CLTV
FILO

ADFG

35

FE

FOCUS ERROR
AMP

Approx.
200 mVp-p

34
AUX1
TEMP 33
FOCNT

V-I
CONVERTER

EQ

35

XSCSY

19

DDI

42

MD1X2

36
96

980 mVp-p

200 ns

100 ns

PB (MD1)

PB (MD2)

79

FOCNT

IC5303
1
2

SEL
31
XLDON
16

4

MONITOR
CONTROL

11
13

12

DADT

OSCI
OSCO
MNT0
MNT1
MNT2
SRDT
SWDT
SCLK
XLAT
SENS

25
26
27
16
17

LRCK
XBCK
256FS
X5403 70.54MHz
512FS

BUFFER
IC5302

MDTI
MBCK
MLRCK

1
2
3

6

8
5
6
7
9

SI
SCLK SV
XLAT SV
SENS

XINT
DQSY
SQSY

PWM
GENERATOR

AD7

TO A/V DATA
CONTROL,
VIDEO OUT
(SE PAGE 3-7)

14

RECP

DPP

16

DADT

24

TO AUDIO
(SE PAGE 3-17)
LRCK
XBCK
FS256

DRAM

SUBCODE
PROCESSOR

20

22.5792 MHz
REC/PB

CLOCK
GENERATOR

Approx.
280 mVp-p

TO MD SERVO
(SE PAGE 3-14)

15

XRST

FS4

PIG

WBL

LASER
DIODE

67

PIG

B
C

ADFM

VC

ASYO

WBL
A

XSCSY

10
A/B TRACK
DETECT
IC5201, 5205(2/2)
Q5201, 5202

EF(XE)
HG(XF)

18 32 33 34

EDEN
EDIEN

SRDTEX

MD1 DIGITAL SIGNAL PROCESSOR
IC5301(1/2)

38

EFWBL
42
GHWBL
41

AMP

17

320 mVp-p
70.54 MHz
REC/PB

XCLR
100

WBL
PEAK & BOTTOM
HOLD

WBL

E&F

28

RF

RF AGC
& EQ

J

E&F

DTRF
CKRF
XLRF

IOBUSY

COMPARATOR

C

SWDT
16
SCLK
17
XLAT 18

SERIAL
COMAND
DECODER

RECP

X5301 22.5792MHz

PLL

I

3

30

CENTER VOLTAGE
GENERATOR
(FOR BIAS)

200 ns: MD1
100 ns: MD2
PB

41

Approx.
1.54 Vp-p
: MD1
Approx.
1.86 Vp-p
: MD2

ADIP
DECODER

G&H

VC

27

SPINDLE
SERVO

VC

PIG

FILTER

DETECTOR

MODE

XLAT
DDX

PIG

DCLK

31

EDEN
40
EDIEN
39

MD1X2

A_B

200 ns
PB (MD1)

XEMG
SRDT
SWDT
SCLK

AGCI

XSTBY 19

TO A/V DATA CONTROL,
VIDEO OUT
(SE PAGE 3-7)

DSYNC

44

OSCI
29
OSCO
28

D OUT

SERIAL COMMAND
INTERFACE

40
Approx.
712 mVp-p

XOE
XWE

LASER
CLOCK
GENERATOR

5

DDO

43

DRV RESET

OPTICAL PICK-UP BLOCK (1/2)

l

XBISY

RFGAIN UP

200 ns: MD1
100 ns: MD2
PB

DIN

REFCK

RFGAIN DOWN

RF AMP
FOCUS/TRACKING
ERROR AMP
IC5002

MAIN DATA SIGNAL
PROCESSING

50

Q5901

GAIN CONTROL AMP
IC5003, Q5005

MAGNETIC
HEAD
DRIVE
SIGNAL
GENERATOR

ATRAC
ENCODER/
DECODER

MHEN

MHEN

5

MON2(HN-H)
MON3(HN-L)
MON4(HP-H)
MON5(HP-L)

CPU
INTERFACE

19

5
6
7
8

XINT

5

43
44
45
46

DRV
RESET

•

1
2
3
4

SHOEH PROOF
MEMORY
CONTROLLER

•

CN5002
(1/2)
43
44
45
46

HN-H
HN-L
HP-H
HP-L

XLAT

OUT A

2
4

HN-H
HN-L
HP-H
HP-L

DQSY

1

CN5803
(1/2)

CN5902

8, 9
4, 5
6, 7
2, 3

11, 12
15, 16 HEAD
13, 14 SWITCH
17, 18 IC5901

SQSY

OUT B

OVER
WRITE
HEAD
DRIVE
Q5902,
5903

EFM/ACIRIC
ENCODER/DECODER

CN5901

RAMDAT0

(SEE PAGE 4-75)

RAMDAT17

(SEE PAGE 4-79)

l

CLV BOARD(1/2)

RAMADR0

HR5901
OVER WRITE HEAD

REC BOARD

RAMADR16

MD2 DIGITAL SIGNAL PROCESSOR
IC5403(1/2)

17

IC5007
VLPC
PD

13

LD

AUTOMATIC
POWER CONTROL
IC5005, Q5002

BUFFER
IC5006(1/2)

7

1

83

6

WRITE PWM

TO MD SERVO
(SE PAGE 3-14)

APCREF

I GAIN

5
3

PD-A

IC5008

11
5 6

7

SIGNAL PATH
2
1

MD SIGNAL

XKSHOCK
MD1
J GAIN

COMPARATOR
IC5205(1/2)

REC
PB

TO MD SERVO
(SE PAGE 3-14)

13

14

TO MD SERVO
(SE PAGE 3-14)

05

3-11

3-12

MD2

MD1/MD2

DCM-M1

3-7. MD SERVO BLOCK DIAGRAM
MAIN BOARD (4/7)

5
•
6

8

TRK+
TRK–

FI1 16

88

RO1

RI1 15

89

3
•
4

31 FO3

FI3 21

86

7
•
8

29 RO3

RI3 22

85

13 FO2
11 RO2

FI2 17
RI2 18

SFDR
92
SRDR
91

TRACKING
MONITOR
IC5006 (2/2)

XPS
3

FRDR

TFDR
TRDR

DIGITAL
SERVO
SIGNAL
PROCESS

PEAK
BOTM
ABCD
FE
AUX1
SE
TE

FROM CPU
INTERFACE

62
63
64
65
66
73
74

XLRF
80
CKRF
81
DTRF
82

AUTO
SEQUENCER

14
TO MD SIGNAL PROCESS
(SEE PAGE 3-11)

CLK
2

IC5015

M5801
SLED MOTOR

1

SIA

2

SIB

OUT

CN5002
(2/2)
38

4

SHOCK

85 KSHOCK EN
31 SHOCK

38

23
20

M

28

4

29
30

2

REFLECT

Approx.
1 Vp-p
: MD1
Approx.
1.32 Vp-p
: MD2

S5801
PROTECT

Approx.
1.38 Vp-p
: MD1
Approx.
1.68 Vp-p
: MD2

M5821
SPINDLE MOTOR

27

1

PROTECT

M5811
HEAD UP/DOWN
MOTOR

3

S5802
REFLECT

S5803
MD 1/2

(DISK TYPE JUDGMENT)

INLMIT

B (2A)
XB (2B)

SLED MONITOR
IC5802, 5807

S5804
INITIAL
HEAD
UP/DOWN

V
W

2A
2B

HEAD UP/DOWN MOTOR DRIVE
IC5601
7

OUT 1A

IN 1A

2

53 ST1A

10 OUT 1B

IN 1B

3

54 ST1B

29

5

IN 2A 16

55 ST2A

30
31

35

35

12 OUT 2B

IN 2B 15

Approx.23.6 ms: MD1
Approx.14.8 ms: MD2
REC/PB

S5805
IN LIMIT
OPTICAL
PICK-UP
POSITION

OUT

1

6

4

PHASE
CONTROL
IC5804-5806,
5808

3

CLV_U_CON
CLV_V_CON
CLV_W_CON

2

SPINDLE
MONITOR
IC5801, 5803

4
6

CLV_U_MON
CLV_V_MON
CLV_W_MON

5
SCLK SELECT
IC5407

7

4

TEMP MON

XLAT SV
SENS
XINT
DQSY
SQSY

CLV_U_CON
45

CLV_VCON

3

CLV_V_CON
46

SPRD

5

CLV_W_CON
47

2

42

4

43

6

44

CLV_U_MON
CLV_V_MON
CLV_W_MON

SPINDLE
CONTROL

88

Approx.12 ms: MD1
Approx.7.5 ms: MD2
REC/PB

5
1

CLV_VCONT

14

4

1
2

9

3
4
2
1

DI
DO
SK
CS PI 7

DRV RESET

11

TO MPEG ENCODE
(SEE PAGE 3-10)

TO MD SIGNAL PROCESS
(SEE PAGE 3-12)

SO

7

SI

4

32

TO A/V DATA CONTROL,
VIDEO OUT
(SEE PAGE 3-7)

TO MD SIGNAL PROCESS
(SEE PAGE 3-12)

40
94

DIGITAL SERVO SIGNAL PROCESSOR
IC5403 (2/2)

94

98
97

ADIP
DECODER
&
SPINDLE
SERVO

SPFDEX

ADIPFM

90

ADFG

SPRD
SPRD

SPINDLE DRIVE
SIGNAL SLECTOR
TO SERIAL COMMAND
INTERFACE

INTERVAL
COUNTER

05

3-13

RESET

6

70
99
27
33

IC5402
14

72
73
74
75

3

SWDT 65

1

3 Vp-p

NV_DI
NV_DO
NV_CLK
NV_CS

SCLK_SYS

17

5

SPINDLE VOLTAGE
CONTROL
Q5801-5803

2

READ DATA SELECT
IC5408

COM

Approx.
560 mVp-p
: MD1
Approx.
780 mVp-p
: MD2

SCLK 63

SRDT 64
INLMIT
PROTECT
REFLECT
MD1_MD2
INITIAL

TO SYSTEM CONTROL
(SEE PAGE 3-15)

15

56 ST2B

95
96
97
98
100

19

NV-RAM
IC5405

13 17 18 26 28 48 49 66 71 81 82 83 87 93

SYS_SEL 67

28

OUT 2A

30

36 SLED1_MON
•
37 SLED2_MON

27

31

1
SPINDLE
MOTOR
PRE-DRIVE
Q5808-5813

1B

41 MR_ADJ

TEMPERATURE
SENSOR
IC5406

U
SPINDLE
MOTOR
DRIVE
Q5821-5826

DRIVE CONTROL
IC5404
REFERENCE VOLTAGE
GENERATOR
IC5401

MR_REF

1A

SE2_MON

23

20
SLED0_MON
16 SLED1_MON 16
•
•
18
18

INITIAL

A (1A)
XA (1B)

7
•
9

MD 1_2

VO1, VO2

FG

SD–

CLV_BRAKE_EN

SLED–

SI

6

21

A/D
DPP
WRITE PWM
I gain0
J gain0

21

61 PS_36

20

7 12 39 57 59

PWM (P67)

5

SD+

6

M

Approx.23.6 ms: MD1
Approx.14.8 ms: MD2
REC/PB

XKSHOCK 86
TELEVEL INT 38
68

CN5801
SLED+

Approx.23.6 ms: MD1
Approx.14.8 ms: MD2
REC/PB

DETECT LEVEL
CONTROL
IC5009,5010

SCLK
SRDT
SWDT

SHOCK
SENSOR

CN5803
(2/2)

XKSHOCK

19

SCLK SV

SHOCK SENSOR AMP
IC5851

SE5851

TELEVEL
INTRRUPT
IC5013

TE

MHEN
PIG
XSTBY
XSCSY
IOBUSY
RFGAIN_UP
RFGAIN_DOWN
MD1X2
XLAT_DDX
SRAM_CS
EDEN
EDIEN
XEMG
A_B

KSHOCK
ENABLE
IC5014

(SEE PAGE 4-68)

DRV REQ

FE

L.P.F.
IC5011,
5012

AD7
DPP
WRITE PWM
I GAIN
J GAIN

CLV BOARD (2/2)

1.58 Vp-p
16.934 MHz
REC/PB

X5401
16.9344MHz

FS4

ERROR LEVEL
DETECT
IC5004

TO MD SIGNAL PROCESS
(SEE PAGE 3-11)

DRV RESET

FCS–

FFDR

FO1

SYS_CS

6

XIN

1
•
2

XOUT

(FOCUS)

(TRACKING)

FCS+

13

ANALOG MUX

CN5001
2-AXIS DEVICE

DIGITAL SERVO SIGNAL PROCESSOR
IC5301 (2/2)

FOCUS/TRACKING COIL DRIVE,
SLED MOTOR DRIVE
IC5602

A/D CONVERTER

(SEE PAGE 4-39, 43)

PWM GENERATOR

OPTICAL PIC-UP BLOCK
(2/2)

3-14

RFEX

92

ASYO

DCM-M1
3-8. SYSTEM CONTROL BLOCK DIAGRAM
MAIN BOARD (5/7)
CN8101
(2/3)
DATA_TO_HI

21

XHI_SCK

TO CAMERA CONTROL
(SEE PAGE 3-6)

IC4007

20

DATA_FROM_HI

IC4008

CAM_DD_ON

B

3

SO

23

167 CAM ENABLE

2

SCLK

24

184 CAM RESET

4

SI

29

186 CAM PWR

CLOCK_EN 182

7

X8001
32kHz

OSC OUT

5

OSC IN

3

9
IC4010
IC4011

CAM_SO

EVF_EN 107

DRV_REQ

TO MD SERVO
(SEE PAGE 3-14)

169 DRV_REQ

3

EVF_EN_SWED

10

7

CN8007
(2/3)
ETHER_PWR 94

36

ETHER_INT 138

33

SBHE_CE2B 104

27

CS6_ETHER 102

26

1.5 Vp-p

ETHER_PWR

K

ETHER_INT
SBHE_CE2B

TO ETHER INTERFACE
(SEE PAGE 3-25)

CS6_ETHER

RATE_TX

D0 – D15

A2 – A13,
A22, A23

DQ0
ı
DQ15

RATE_CTS
DEV_RESET

2

34

174 RATE_RX

DQMUL_ICIORD 91

29

176 RATE_CTS

DQMUU_ICIOWR 92

28

RD/WT 93

31
ADDRESS BUS

TO MPEG ENCODE
(SEE PAGE 3-10)

DQMLU_WE1 90
CS3_SDRAM 99
SWITCH
Q8005

177 DEV_RESET

SH_3.1V

IC8007

CAS 108

2

RAS3L 106

1

4

IC8006

KIO 162

1

WAIT 123

2

193 XRESET

2

2

185 DRV_PWR

SYS_WAIT

SYSCHIP_INT
FSY_INT
CPU_CS4_100
64M FLASH
IC8005

CLE 110
ALE 112
CE 113

DEV_RESET
2

CLE

3

ALE

43 CE
41 R/B

RDY_BUSY 191
1M EEPROM
IC8004
CSO_ROM 96

1
ı
4•
7•
10
ı
20
•
31

A0 – A16

21
I/O-0 ı
ı 23
•
I/O-7 25
ı
29

D0 – D7

30 CE
SWITCH
Q8013
SWITCH
Q8012
SWITCH
Q8014

5

WE

32 OE
9

RDY/BAO

6

RES

A0
ı
A6

RE 42
WE 4
18
I/O-0 ı
21
ı
•
I/O-7 24
ı
27

D0 – D7

D0 – D31

8

WP 5
A0 – A23

05

3-15

RD & WT

RD

SYSCHIP_INT 137

6

1

DQMUU_ICIOWR

DQMLU_WE1

RD 88

CS4_SYSCHIP 100

IC8023
2

ETHER_WAIT
DQMUL_ICIORD

DQMLL_WE0

FSY_INT 139
IC8013

A0 – A3

DQMUU_ICIOWR
4

CS2_FLASH 98
4

D0 – D15

DQMUL_ICIORD

CKE 105

IC8010

VOUT 3

21
ı
24

15 39 16 19 17 18 37 38

DQMLL_WE0 89

1

A0 – A3

1

170 RATE_RTS

RATE_RX

VCC 4

D0–D15

IC8025
4

CLK

CKE

/CE

/RAS

A0
ı
A13

/CAS

2 • 4 • 5 • 7 • 8 • 10 •
11 • 13 • 42 • 44 • 45 •
47 • 48 • 50 • 51 • 53

/WE

20 – 26 •
29 – 35

UDQM

D16 – D31

15 39 16 19 17 18 37 38

64M SDRAM
IC8003

UDQM

CLK

CKE

DQ0
ı
DQ15

A2 – A13,
A22, A23

168 RATE_TX

RATE_RTS

12

A0
ı
A23

2 • 4 • 5 • 7 • 8 • 10 •
11 • 13 • 42 • 44 • 45 •
47 • 48 • 50 • 51 • 53

/RAS

REC/PB

20 – 26 •
29 – 35

/CAS

156 EXTAL

1.1 Vp-p
9.8304 MHz

53 – 56
• 58 •
60 – 68
• 70 •
72 – 78
• 80 • 82

/CE

X8003
9.8304MHz

qg

64M SDRAM
IC8002

A0
ı
A13

155 XTAL

1
ı
4•
6
ı
9•
11
ı
13
•
15
ı
19

ADDRESS BUS

/WE

5 EXTAL2

D0
ı
D31

UDQM

X8002
32KHz

DATA BUS

13 – 18
• 20 •
22 – 26
• 28 •
30 – 32
• 34 •
36 – 44
• 46 •
48 – 52

UDQM

4 XTAL2

REC/PB

4

EVF_SO

7

qh

32.768 kHz

RESET
IC8009

8

190 ADA_EN

TO AUDIO
(SEE PAGE 3-17)

J
TO EVF
(SEE PAGE 3-21)

EVF_SCK

7
6

189 ATRAC2_EN

ADA_EN

19

3

1

5

164 CAM_SO

ATRAC2_EN

18

165 CAM_SCK

IC4011

EVF_SI

9

1

5

2

CAM_SCK

CN4511
(2/2)
2

6

32.768 kHz
REC/PB

LCD_EN 103

LCD_EN_SWED

14

7

8

TO CAMERA SIGNAL PROCESS
(SEE PAGE 3-4)

171 CAM_SI

LCD_SO

1
CN4313 (3/3)

IC4010

CE

I
TO LCD
(SEE PAGE 3-19)

LCD_SCK

2

1

408 mVp-p

CAM_SI

3

6

IC4008

RFAL TIME CLOCK
IC8008

LCD_SI

3

7

2

SYSTEM CONTROL
IC8001

CAM_XCS

2
1

5

22

CAM_RST

CN4312
(1/2)

IC4007
6

DATA BUS

C

(SEE PAGE 4-48, 59)

3-16

TO A/V DATA CONTROL,
VIDEO OUT
(SEE PAGE 3-8)

DCM-M1

3-9. AUDIO BLOCK DIAGRAM

ETHER BOARD
(1/2)

MAIN BOARD (6/7)
(SEE PAGE 4-48, 56)

(SEE PAGE 4-109)

ETHER ADAPTER
(1/2)

CN8801
(1/2)

CN8802
(1/2)

LINE IN

W_JACK_DET
LINE_R
LINE_L

19
1
3

JACK BOARD (3/4)

HP/LINE AMP
IC3007
W_JACK_DET
LINEIN_R
LINEIN_L

59
53
55

(SEE PAGE 4-119 )
CN3002 (3/4)

CN8007 (3/3)

AD/DA CONVERTER
IC3004

59
53
55
37

38

RIN3

23

LIN3

26

VCOM
VREF

OPGAR

ROUT2

OPGAL

LOUT2

28

15

29

16

INR

OUTR

INL

OUTL
NF1

JACK BOARD (2/4)
(SEE PAGE 4-119)
21
26
30

MIC AMP
IC3001

41

5

17
EXT

44

BIAS

NF2
MUTE

11

LINEOUT-R

20

16
19

LINEOUT-L
SP_IN

16
19

BEEP
21

SP SWITCH
IC3003

2
CLOCK
DIVIDER

13

14

15

1

7
3

1

5

3 2

5

6

4

MAIN CONTROL
SWITCH UNIT
(1/2)

–
+

(SEE PAGE 4-62)

SP AMP
IC3008

IC3005

CN8001
(1/2)

OFF

HPF

2

12

CAM_SO

SP_VDD

DADT

AT_INSL

9
3.84 Vp-p

AT_RESET

18

19

CAM_SCK
CAM_SO
ATRAC2_EN
AT_EXEC
AT_STRO
AT_MUTE
AT_REC
AT_ATRAC2
AT_LEVEL3

15

20
23
24
39
40
46
47
49
50

EXTAL

CLOCK
GENERATOR

XRST

RESET
CIRCUITR

SCLK
SWDT
XLAT
LEXC
STRO
MTE
REC
ATRAC2
LEVEL3

17
•
19

SP–

18
•
20

3

REC/PB

34

AUDIO I/F

SHOCK
PROOF
I/F

ACLK
ACDI
XABS
ACDO
XARQ

25
28
29
31
32

ACLK
SYS_ACDO
XABS
SYS_ACDI

3

TO A/V DATA CONTROL,
VIDEO OUT
(SEE PAGE 3-7)

XARQ

MICRO
COMPUTER
I/F

SIGNAL PATH
MD SIGNAL
PROGRAM
ROM

DSP CORE

DATA
RAM & ROM

MD1
REC
PB

05

3-17

17
•
19

AIDT

BCK

38

LRCK

36

33

DODT

35

DIDT

JNSL
512FS

SP+

4.24 Vp-p

ATRAC
IC3009
45

16

CN8301 (1/2)
18
•
20

44.1 kHz

REC/PB

TO SYSTEM CONTROL
(SEE PAGE 3-15)

SP_BEEP

XBCK
LRCK

AMUTE
HP_BEEP
HP_JACK_DET
SP_NMUTE

SD BIAS

11.2896 MHz

TO MD SIGNAL PROCESS
(SEE PAGE 3-12)

5

1

4

256FS

CAM_SI

CAM_SCK

ADA_EN

ADA_RESET
PWR_DWN

MIC_ATT

W_JACK_DET

MIC_JACK_DET

XWIND

25

–
+

4

ON

TO MPEG ENCODE
(SEE PAGE 3-10)

VIDEO OUT
4 JACK DET

13

REC/PB

12
–
+

17

BEEP

2..8224 MHz

ATT
SWITCH
Q3001

14

HP_L

J3002

INVERTER
Q3002

CONTROL
REGISTER
I/F

FILTER

6
11

11

4.32 Vp-p

+
–

20

LOUTL

46 XRST

21
20
10
9

8

LINL

LIN1

FILTER

MIC1001

14

MUTE
23

47 PD
+
–

11

HP_R

15

J3003 (2/2)

SDTO

23

RIN1

4

CN3003 (3/4)
HP_COM

AUDIO/VIDEO

AUDIO
I/F
CONTROL

XCS

3
4

1

OFF

19
24

DA
L
CONVERTER OUT1
25

BCLK
LCLK

HPF

L CH

+
2
–

43

17

9

ON

18

1
2

7

3

13
INT

R CH

+
–

6

8

LOUTR
LINR
17

24

IC3002

EXT

2

PGAL

LIN2

15

18

30

INT

CN3001

36

AD
ADCL CONVERTER
35

CN3002 (2/4)

29

MIC2001

32

SDTI

MICIN_R
MICIN_L

31

MCLK

21
26
30

MIC_JACK_DET

R
OUT1

ADCR

CDTI

CN3003 (2/4)

CCLK

MIC
PLUG IN POWER

40

PGAR

RIN2

CDTO

J3001

6

3-18

AUDIO
SIGNAL

SP3001
(SPEAKER)

DCM-M1
3-10. LCD BLOCK DIAGRAM

LCD BOARD (1/2)
4 Vp-p

(SEE PAGE 4-106)
2H
REC/PB

LCD DRIVER
IC4302

LCD UNIT
LCD4301
4 Vp-p

560 mVp-p
2H
H

REC/PB
REC/PB

CN4303

PANEL_Y

E
TO A/V DATA CONTROL,
VIDEO OUT
(SEE PAGE 3-8)

CN4306

3

BUFFER
Q4303, 4304

8

4

BUFFER
Q4305, 4306

9

5

BUFFER
Q4307, 4308

10

PANEL_R-Y

PANEL_B-Y

220mVp-p

LCD_XVD

11

LCD_XHD

12

XVD

G/Y

G_OUT

PICTURE

R/R-Y/CR

R_OUT
CLAMP

GCA

MATRIX

GAMMA

CLAMP

CLAMP

INV

B/B-Y/CB

B_OUT

REC/PB

XHD

I

18 CS/LD

1

2

6

LCD_13V

1

LCD_2.85V

2

LCD_–15V

3

LCD_4.95V

24

A05

5

40

A01

1

39

A06

6

30

A04

4

31

A03

3

32

A07

7

35

REC/PB

COLOR

TG-24

BRIGHT

TG-12

RGB_AMP

TG-23
TG-22

COM_OUT

SUB_BRT_B

41

TG-20

COM_AMP

TG-13
TG-17

14

COM_AMP

XTEST

EXT_BGP

19 CLK

48

38

37

18
17
16
15
14

TG-21

SUB_BRT_R

17 DO

13

TG-18

CONT

COM_FRP

A02

12

LCD_SCK

21

VR

VB

VGH
2.85V (TG) (VDO)
VGL

LCD
PANEL

LCD_4.95V (VSH)

2H

RIGHT

CN4302 (1/2)

LCD_SI

24

VG

4 Vp-p

DOWN

TO MPEG ENCODE
(SEE PAGE 3-10)
LCD_EN_SWED

22

REC/PB

FRP

14

20

H

BLACK IN

H

13

RIGHT

20

236 mVp-p

H

D/A CONVERTER
IC4301
DOWN

22

1.26 Vp-p

13
12
9
8

TG-16

7

TG-15

2H
REC/PB

6

TG-14

5

29 28

23

LCD_SO

20 DI

14

10

MODE1
MCLK
HCNT
OE
SRTL
SRTM
SRTR
MODE2
RESET
GSRT
GPCK
GRES
CS
VCOM

TO SYSTEM CONTROL
(SEE PAGE 3-16)
TIMING GENERATOR
IC4303
CN4305
A10 10
BL_LVL
V_COM
VCO

8

A11

9

A09

1
2

PHOIN
PHOOUT

BGP
SW

VG

3

XTST

9

PANEL_COM

SW_COM 10
A12 12

11 A08

47 COMTST

PANEL_XHD

FRP 11
HDB

HSY

4

SYF

SYF 33
SRT1 22
ı
ı
SRT3 20
MCLK 24
OE 23
RIGHTO 18
RESET 17
DOWN
RIGHT
3.1 Vp-p
V

XVD

REC/PB

XHD

GSRT 16
44 DOWN

GPCK 15
GRES 14

46 RIGHT

DOWNO 13
HCNT 12

34 QVD/XVD

BL (–)

OSCI 27

4
6
7

FOR JIG

ND4307
BACK LIGHT

8
1
2

TG-23
TG-18
TG-17
TG-16
TG-15

COM AMP
IC4304 (2/2)

3.12 Vp-p
15.4 MHz
REC/PB

5

TG-14
TG-13
TG-12

6

+
–

7

COM DRIVE
Q4312, 4313

CN4307

FILTER
IC4304 (1/2)

UNREG

INVERTER
UNIT
IV4301

LCD_4.95V

3.6 Vp-p

BL_LVL

V_COM

VCO

3
2

VIDEO SIGNAL
CHROMA
PB

05

3-20

BL_HIGH
BL_LOW
LED
BL_GND

D4317
(LED)

SIGNAL PATH
REC/PB

10

1

VCO

H

3-19

FLUORESCENT
TUBE

TG-24

PD 32
OSCO 26

37 CSY/XHD

BL (+)
TG-20, TG-21, TG-22

3
9

Y

DCM-M1

3-11. EVF BLOCK DIAGRAM

VF BOARD
(SEE PAGE 4-87)
208 mVp-p

500 mVp-p

8 Vp-p

8 Vp-p

H

2H

LCD DRIVER
IC4501

REC/PB

2H
REC/PB

H
REC/PB

CN4601

CN4501

F
TO A/V DATA CONTROL,
VIDEO OUT
(SEE PAGE 3-8)

EVF_Y

EVF_R-Y

EVF_B-Y

19

BUFFER
Q4502, 4503

8

18

BUFFER
Q4504, 4505

9

20

BUFFER
Q4506, 4507

10

G/Y

AGC

R/R-Y/CR

CLAMP

G OUT

PICTURE

GCA

CLAMP

MATRIX

S/H

GAMMA

CLAMP

R OUT

INV

B OUT

B/B-Y/CB

9

20

11

24

13

204 mVp-p

BUF IN

2H

4

COLOR

2

6

GAMMA1

9

33

CONTRAST

5

40

BRT

1

39

18 LD

TO SYSTEM CONTROL
(SEE PAGE 3-16)

8

D_CLIP

6

27

SUB_BRT_B

4

31

SUB_BRT_R

3

32

BUF OUT

PICTURE

COM

15

10

14

9

13

12

16

8

12

1

11

2

10

3

9

4

7

5

6

6

5

7

4

13

3

G

R

B

COM (5.7V)

VF LCD
CN BOARD
LCD4701

15

16

BLK

GAMMA1
BRIGHT

CLR
EN

SUB BRT B

VCK1

SUB BRT R

VCK2

14

CLR

23

EN

25

VCK1

27

VCK2

29

VST

INV CURRENT

HST

21

REC/PB

BLACK LIMIT

HCK2

19

HST

2H

HCK1

17

HCK2
8 Vp-p

CONTRAST

BLK

15

HCK1

45 46 47 48
7

B

7

COLOR

RGB BLK

EVF_EN_SWED

17 DO

R

CN4702

11

VST

30

EVF_12V

1

FRP

J

3

19 CLK

AGC LEVEL

EXT BGP

2

EVF_SI

5
1

SHR

EVF_SCK

AGC 11
PICTURE 10

20 DI

SHG

1

G

AGC DET

SHA

EVF_SO

EVR
IC4502

SHB

REC/PB

CN4701

22

8

BLK
HCK1
HCK2
HST
CLR
EN
VCK1
VCK2
VST
VVDD (12V)
GRT (12V)

28 29

VCO

LCD TIMING GENERATOR
IC4602
SH3 34
SH1 32
SH0 30
VCO

42 CKI

SH2 38

41 CKO

XCLP 35
SBLK

EVF_XVD

45 XVD

FRP 28

21

27 XHD

CLR 16
EN 17
VST1 18
VCK2 20

39 RPD

VCK1 21
HST1 22
2.16 Vp-p

HCK2 23

11 MHz

HCK1 24

REC/PB

(SEE PAGE 4-97)

5

17

BLK 12

EVF_XHD

BL BOARD

BLK
EN
VST
VCK2

3.6 Vp-p

FB

18

VCK1

6

HST

DRIVE_PULSE

21
19

EVF_BL_4.95V
6

8

OSC

4

–
+

V
H

REC/PB

15

REC/PB

9
10

+
–

SHORT
CIRCUIT
PROTECTION

12
2

12 Vp-p
H

CN4901

11

5

DISCHARGE
SWITCH
Q4601

G

4

EVF_4.95V (–)
3

2.5V REG
EVF_4.95V

EVF_4.95V
VCO

2

FOR JIG

1
SIGNAL PATH
VIDEO SIGNAL
CHROMA
PB

05

3-21

T4701

SWITCHING
Q4701

25

DRIVE PULSE GENERATOR
IC4601

HCK2
HCK1

BL_LOW

14

7

3.1 Vp-p

BACK LIGHT
ND4701

CLR

3-22

Y

DCM-M1

3-12. MODE CONTROL BLOCK DIAGRAM
LCD BOARD (2/2)

MAIN BOARD (7/7)

(SEE PAGE 4-106)

SYSTEM CONTROL
IC8001

(SEE PAGE 4-29, 48, 56, 59)

SH3.1V
CN4302 (2/2)

CN4312 (2/2)
TP Y1 118

UPPER CONTROL SW SUB ASSY
(SEE PAGE 4-65)

KEY AD1

6
S8311

S8308

S8306

S8303

SH3.1V

TP X1 117
KEY AREC

3
5

KEY PLAY & PAUSE
KEY STOP

4
VOL

S8315

S8312

10 KEY AREC

5

11 KEY PLAY/PAUSE
S8001, 8003

141 OPEN/CLOSE
S8002
142 HALF LOCK

AUDIO REC
A REC LED

1

CN4301

188 KEY EJECT
S8003

S8002
HALF LOCK
DETECT

1

A REC LED

TP IY1 207

8

TP IX1 204

6

TP IY0 206

7

TP IX0 203

5

MAIN CONTROL SWITCH UNIT (2/2) (SEE PAGE 4-62)

S8306

FOCUS
INFINITY

BACK LIGHT
7

MARK

PHOTO

2

2

1

S8304

S8302

S8301

ERASE

MENU

EXPOSURE

KEY AD2

1

KEY VREC
129 LCD REVERSE

KEY PHOTO

7

9

5

TOUCH
PANEL

TP IX0

TP X0

SWITCH
Q4302 (2/2)

5

9

TP Y0

SWITCH
Q4301 (2/2)

6

LANC OUT 192

KEY PHOTO

PUSH ENTER
9
10

KEY KURU1
KEY KURU2

10

127 KEY KURU1

9

128 KEY KURU2

RV8301
ZOOM

10

TP Y0 120

A2.85V

4

10

TP IY0

ETHER STB 116

JOG

W

TP IX0

TP IX1

130 LCD OPEN
8

SEL/

2

MULTI_WAKE 187

202 KEY AD2

S8300

PHOTO

3

8

8

7

S8308

9

TP IY0

TP IY1

CN8001 (2/2)

CN8301 (2/2)

KEY PLAY EDIT

S8307

FOCUS

4

TP IX1

KEY CAMERA

2
1

7

LANC IN 115

CN8302

KEY INTERVIEW

CN8303

TP IY1

RMC IN 159
TP X0 119

(SEE PAGE 4-62)

SWITCH
Q4302 (1/2)

4

S8001

OPEN/CLOSE
DETECT

D8301

TP X1

LANC WAKE 12

143 KEY STOP

4

S8309

11

LANC DETECT 140

3

D2.85V

ZOOM SWITCH UNIT

SWITCH
Q4301 (1/2)

3

201 KEY AD1

6

S8301

DSPL

TP Y1

CN8002

CN8301

S8314

12

131 135 133

4
S8303

ZOOM

POWER
T

5

INTERVIEW

6

KEY INTERVIEW
KEY CAMERA

6
5

CAMERA
OFF
7

PLAY/EDIT

LCD DETECTION SW FLEXIBLE BOARD

11

(SEE PAGE 4-65)

LCD REVERSE
DETECT
S8022
LCD
OPEN/CLOSE
DETECT

KEY VREC

6

8

7

3 2

12

1
2

4

IC8015

S8305
(START/STOP)
13

S8021

KEY PLAY EDIT

IC8016

1

5

ZOOM SW

CN8101 (3/3)

CN8021
6

LCD REVERSE

LCD REVERSE

28

14

ZOOM SW AD

D

TO CAMERA CONTROL
(SEE PAGE 3-6)

CN8006
6

SH3.1V
PCONT 4

3

LCD OPEN

LCD OPEN

REMOTE CONTROL
RECEIVER
IC1

CN1
OUT 2

D2.85V

1

RMC OUT

SWITCH
Q8011

3

8 EVER 5V
DOUT 10

CN8003
BUFFER
Q8006

1

CN3002
(4/4)

IC8026
1

4

2

L DC 14
12 D IN
LOUT 11

29

LANC VCC OUT

27
25

LANC DET
LANC DATA

CN3003
(4/4)

J11
CN8004

29

2

27

3

25

4

LANC VCC OUT
LANC DETECT
LANC DATA

CN11
2
3
4

05
4

REMOCON RAY-CATCHER
BLOCK UNIT

D1
(CAMERA RECORDING)

V REC LED

4

V REC LED

10

TO MPEG ENCODE
(SEE PAGE 3-10)

LANC DRIVER
IC8027

JACK BOARD
(4/4)

(SEE PAGE 4-65)

3-23

(SEE PAGE 4-119)

3-24

REMOTE
TERMINAL
UNIT
(SEE PAGE 4-119)

REMOTE

DCM-M1

3-13. ETHER INTERFACE BLOCK DIAGRAM

LEVEL SHIFT
IC8801

ETHER BOARD (2/2)
(SEE PAGE 4-109)

D0 – D7

14 B0
I

A0 3

I

I

21 B7

I

A7 10

T/R
2

SD0 – SD7

OE
22
ETHER INTERFACE
IC8806

CN8801 (2/2)
LEVEL SHIFT
IC8802

1
I

I
•

25

I

•

•

11

TO SYSTEM CONTROL
(SEE PAGE 3-16)

D8 – D15

14 B0
I

A0 3

I

I

21 B7

I

A7 10

SD8 – SD15

I

29

I

•

13

85

•

DATA BUS

SD0 – SD15

•

15

T/R
2

I

19
RD&WT

27

87

OE
22

I

91

31
LEVEL SHIFT
IC8803

21

SBHE_CE2B
DQMUU_ICIOWR
DQMUL_ICIORD
CS6_ETHER

24
27
28
29
26

I

A0 – A3

14 B4

A4 7

I

I

I

I

17
19
20
21
18

B7
B2
B1
B0
B3

A7
A2
A1
A0
A3

10
5
4
3
6

SA0 – SA3

4
I

7
11
17
15
82

SA0 – SA3
BHE
IOW
IOR
ECS

OE
22

ADDRESS BUS

SYSTEM INTERFACE

A0 – A3

ENCODER/DECODER

9

DO – D15

CN8802
(2/2)

DETA LINK CONTROLLER

K

23

•

6

IO BASE-T TRANSCEIVER

4

TPIP
TPIN

71
72

3
1

13
14

77
78
79
80

7
6
5
4

CLKO

CLKI

61
X8801
20MHZ
62

18

14 B7
15 B6

A7 10
A6 9

92
3

OE
22
ETHER_PWR

BUFFER MANAGER

l

33
34

DATA BUS

34

BD0 – BD7

l

41
42

BD0 – BD7

l

5

l
•

53

•

BD0 – BA14

17

ETHER_RESET

32

14 B7

A7 10

l

•

l

BCS
BWE
BOE
64

HWRST

60
30
32
33

27 CE
6 WE
1 OE

TO MPEG ENCODE
(SEE PAGE 3-10)

05

3-25

A0
A14

28

•

58

G

8
l

56

36

l

22 I/O8

2

47
50

•

26

l
•

BA0 – BA14

20 I/O1
l

45

ADDRESS BUS

LEVEL SHIFT
IC8804

8

9

9

10

1.28 Vp-p
20 MHz
REC/PB

LEVEL SHIFT
IC8805

INT
READY

7
8

RD+
RD–

10BASE-T
TPOPA
TPOPB
TPONA
TPONB

SRAM
IC8808

ETHER_INT
ETHER_WAIT

ETHER ADAPTER
(2/2)

PULSE TRANSFORMER
IC8807

18

3-26

TD+
TD–

DCM-M1
3-14. POWER 1 BLOCK DIAGRAM
BATTERY TERMINAL

POWER BOARD
(SEE PAGE 4-130)
CN9002
BATT_SIG
AC_DETECT

LITIUM_BATT_ –
(AC_IN_ –)
LITIUM_BATT_+
(AC_IN_+)

U_GND

1

3

3
5

4

LITIUM BATT_+

BATT_SIG
AC_DETECT
DD_CTL

F9001 L9001

L
TO MAIN BOARD
CN9101 (2/2)
(SEE PAGE 3-30)

1
F9002 L9002
58
•
60
•
62
•
64
•
66
•
68
•
70

F9004 L9005
UNREG
F9003 L9003

SWITCHING CONTROL
IC9001

VREF

STANDBY3
29
•
30 STANDBY
L9004

63

OUTPUT
CIRCUIT

PWM
COMP

COMP
13
•
28 VCC

OUTPUT_6

SWITCHING
Q9003

L9007

L9013

2.3V

34
•
36

UNREG

2.3V

27
4

800 mVp-p
470 kHz
REC/PB

INVINPUT_6

OUTPUT
VCCC_4&5&6

ERROR
AMP

NONINVINPUT_6

11
10
SWITCHING
Q9004

42 OUTPUT
VCC_1&3
51 OUTPUT
VCC_2

OUTPUT
CIRCUIT

PWM
COMP

OUTPUT_5

INVINPUT_5
ERROR
AMP

2.88 Vp-p

NONINVINPUT_5

L9008

64

48

15

L9009

SWITCHING
Q9009

OUTPUT
CIRCUIT

OUTPUT_4
MOSGATE_4

470 kHz
REC/PB

ERROR
AMP

INVINPUT_4

57
SWITCHING
Q9007

60

20
L9016

OUTPUT
CIRCUIT

OUTPUT_3

–20V

38

19
L9020

SWITCHING
Q9001
PWM
COMP

12
•
14
•
16
•
18

A2.85V

5.44 Vp-p
470 kHz
REC/PB

–6.5V REGULATOR
Q9002, 9010

4

ERROR
AMP

L9015

INVINPUT_3

13V
12V REGULATOR
IC9002

33

6 IN

840 mVp-p

SWITCHING
Q9005

470 kHz
REC/PB

L9018

L9006

PWM
COMP

ERROR
AMP

INVINPUT_2

A2.85V (NF)

–20V

–6.5V

13V

OUT

4

FB

3

2

12V

4.95V (CAMERA)

4.95V (CAMERA)
6

L9023
OUTPUT_2

A2.85V

T9001

470 kHz
REC/PB

OUTPUT
CIRCUIT

D2.85V (NF)

56
32

1.44 Vp-p

D2.85V

840mVp-p

16

470 kHz
REC/PB

PWM
COMP

40
•
42
•
44
•
46

D2.85V

4.95V (ETHER)

8•
10

4.95V (ETHER)

L9017

4.95V (VIDEO)

50
•
52

4.95V (VIDEO)

L9019

4.95V (DRIVE)

54
•
56

4.95V (DRIVE)

50

36

940 mVp-p
470 kHz
REC/PB

SWITCHING
Q9006
OUTPUT
CIRCUIT

PWM
COMP

ERROR
AMP

OSC

TIMER
&
LATCH

OUTPUT_1
MOSGATE_1

INVINPUT_1

L9010

22
•
24
•
26
•
28

D3.1V

46
SWITCHING
Q9008

43

30

39

5.52 Vp-p
470 kHz
REC/PB

05

3-27

3-28

M
TO MAIN BOARD
CN9101 (1/2)
(SEE PAGE 3-29)

L9021

AC_DETECT_SW

CN9001

2

L9022

BATT_SIG

D3.1V

D3.1V (NF)

DCM-M1

3-15. POWER 2 BLOCK DIAGRAM

ETHER BOARD

MAIN BOARD
(SEE PAGE 4-29 to 59)

CN8007
40

TO POWER BOARD
CN9001
(SEE PAGE 3-28)

CN8002

(SEE PAGE 4-109)

D3.1V

IC8801 IC8804
IC8802 IC8805
IC8803

40

8 10

•

•

39
36

ETHER PWR

SWITCH
Q8801

2

D2.85V

UPPER CONTROL
SW SUB ASSY
(SEE PAGE 4-65)
CN4511

CN1
3

IC8806
IC8808

2

D2.85V

3

RMC VCC

D2.85V
IC1

2

2.8V
REGULATOR
IC9104

REMOCON RAY
–CATCHER
BLOCK UNIT

EVF A2.85V
17
•
18
EVF D2.85V
19
•
20

EVF PWR1

(SEE PAGE 4-65)

36

SWITCH
Q9115, 9116

EVF 4.95V
13
•
14

SWITCH
Q9113, 9117

EVF 12V
15
•
16

P
TO VF BOARD
CN4501
(SEE PAGE 3-32)

EVF PWR2
12V

12V

12V

2

EVF PWR3
–20V

–20V

38

–20V
LCD PWR2

13V
D3.1V
D3.1V (NF)
2.3V
4.95V (VIDEO)

13V

32
22 • 24 •
26 • 28
30

13V

D3.1V
3.1V
REGULATOR
IC8202

IC8601

2.3V

34 • 36

IC8101

SWITCH
Q4003, 4004

IC4005

EVF PWR1
EVF PWR2
EVF PWR3
LCD PWR1
LCD PWR2
LCD PWR3
LCD PWR4
XLCD PWR5

C CUT OFF 101

D2.85V
D2.85V (NF)
A2.85V (NF)
A2.85V
4.95V (DRIVE)

IC4006
IC4007
IC4008
IC4009
IC4010
IC4011

48
20
12 • 14 •
16 • 18
54 • 56

SWITCH
Q3003, 3004

IC4001
IC4002
IC4003
IC4004

3.2V
REGULATOR
IC8012,
Q8001, 8002

3.2V
REGULATOR
IC8011

6

RESET
IC8009

4

LCD 4.95V

SH 3.1V
UNREG

IC8023

1

12
A2.85V (DRIVE)
•
24
4.95V (DRIVE)

1

MAIN PWR 178

1

IC8023
5

IC8010

2

SDRAM PWR 180
3
179 XCPU PWR
AC DETECT 151
IC8013

IC8023
DRV PWR 185
UNREG WATCH 199

6

2

PS A_B 62
BUFFER
Q8009, 8010

5 INFOBATT SI
29 INFOBATT SO

CN8001

CN9101 (2/2)

N

3-29

O

1

BATT SIG

3
AC DETECT

TO MAIN CONTROL SWITCH UNIT
CN8301
(SEE PAGE 3-31)

DD CTL

5

SH 3.1V

TO VC-216 BOARD
CN101
(SEE PAGE 3-31)

A2.85V (CAMERA)

CAM DD ON

11 2

L

TO POWER BOARD
CN9001
(SEE PAGE 3-28)

3-30

LD-VCC
18
•
19
PD-K
12
MDEN
17
32

SWITCH
Q5102

IC5003
IC5102

SWITCH
Q5203, 5204

IC5201
IC5205

ADCS 84

3 UNREG MON

29

SWITCH
Q5001

XMOD 15

4

94 ETHER PWR
186 CAM PWR

CN8101

CN5001
SWITCH
Q5003, 5004

SWITCH
Q5009, 5010

2
1

IC5004 IC5010
IC5005 IC5011
IC5006 IC5012
IC5009

LDON 14
IC5301
IC5302
IC5401
IC5402
IC5405
IC5406
IC5407
IC5408
IC5501

TO CLV BOARD
CN5803
(SEE PAGE 3-32)

IC5601

DRV REG 16

IC3003
IC3004
IC3007
IC3008
IC5002
IC5007
IC5008
IC5013
IC5014
IC5015

R

UNREG

48

DRIVE CONTROL
IC5404

IC8004
IC8013
IC8015
IC8016
IC8025
IC8026

13V

MH-V
47
•
49

IC5602

XSTPON 89

7

200 DD WATCH
2

9

SWITCH
Q5602

IC8002
IC8003
IC8005
IC8006
IC8007
IC8014

IC8024

IC8008

VCC 4

1.9V

4

13
•
15

SH 3.1V

SWITCH
Q8003

4

OUT 3

A2.85V (CAMERA)

6

LCD PWR4

DC-DC CONVERTER
Q5601, 5603
IC5603

A2.85V

SYSTEM CONTROL
IC8001

–6.5V

SWITCH
Q9107, 9110

LCD 2.85V

CN4312

IC8012
IC8013
IC8602
IC8701
IC8702
IC8703

4.95V (DRIVE)

SWITCH
Q8008

4

4.95V (CAMERA)

9

LCD 13V

LCD PWR1

SH 3.1V

A2.85V

SWITCH
Q8007

U8001

05

2.8V
REGULATOR
IC9103

IC3001
IC3002

4.95V (DRIVE)

SWITCH
Q8004

IC8010
IC8023
IC8024

35 34 • 36

8

LCD PWR3

UNREG

D2.85V

40 • 42 •
44 • 46

37

SWITCH
Q9105, 9108

LCD 6.5V

Q
TO LCD BOARD
CN4302, CN4303
(SEE PAGE 3-32)

MIC PWR 112

UNREG

38 • 40

7

13

58 • 60 •
62 • 64 •
66 • 68 •
70

39

6.5V
REGULATOR
Q9101, 9103, 9111

LCD –15V

CN5002

1.9V
REGULATOR
IC9102

4.95V
(CAMERA)

5

IC8027

PROTECT
Q9122

–6.5V

CN4313

XLCD PWR5

86 85 84 10 11 12 13 14

UNREG VCC
MONITOR
Q9125, 9126

–15V
REGULATOR
Q9102, 9104, 9112

4.95V (VIDEO)
MPEG2 RATE CONTROL & SYSTEM CONTROL
IC8501

UNREG

IC3005
IC3009
IC5303
IC5403
IC8020
IC8104

4.95V (VIDEO)

50 • 52

12V

M

4.95V (ETHER)

4.95V (ETHER) 38
•
39

D2.85V

CN8003

CN9101 (1/2)
38

CN8301
2

CN8801

VCC

OPTICAL
PICK-UP
BLOCK

DCM-M1
3-16. POWER 3 BLOCK DIAGRAM
VC-216 BOARD

VF BOARD

BL BOARD

(SEE PAGE 4-13, 17)

(SEE PAGE 4-87)

(SEE PAGE 4-97)

CN4501

CN101
TO MAIN BOARD
CN8101
(SEE PAGE 3-29)

N

4.95V (CAMERA)

38
•
40

A2.85V (CAMERA)

34
•
36

TO MAIN BOARD
CN4511
(SEE PAGE 3-30)

IC104

IC202

P

EVF 4.95V

CN201
SWITCH
Q203

CAMERA MICON
IC106

8

MF VCC

SWITCH
Q4602, 4603

MF
BLOCK

SWITCH
Q201

5•
23

SENSE VCC

FOCUS/
ZOOM
SENSOR

EVF A2.85V

LENS RST LED 16

35

EVF BL 4.95V

26
•
27

22
•
24

EVF 12V

16
•
17

9•
10
11
•
12

CN4901
EVF D2.85V

13
•
14

EVF 4.95V

IC4602

2•
3

FOR JIG

CAM DD ON

SWITCH
Q102

37

SWITCH
Q103,104

29

LCD BOARD
(SEE PAGE 4-106)

12V

IC001

SWITCH
Q101

39

CN4303
TO MAIN BOARD
CN4312, CN4313
(SEE PAGE 3-30)

Q

LCD 13V

CN4306
VGH

1

7
IC4304

LCD –15V
LCD 2.85V

3
2

10
6

VGL
2.85V (TG) (VDD)
LCD
PANEL

IC4301
IC4303
LCD 6.5V
LCD 4.95V

MAIN CONTROL
SWITCH UNIT

ZOOM
SWITCH UNIT

(SEE PAGE 4-62)

(SEE PAGE 4-62)

TO MAIN BOARD
CN8001
(SEE PAGE 3-29)

O

A2.85V (CAMERA)
SH 3.1V

CN8302

1

24

INVERTER UNIT
IV4301

2

VCC-ZOOM

6

BL HIGH

10

BACK
LIGHT

CN4305

SH 3.1V

11

LCD 4.95V (VSH)

CN4307

BL

CN8303
6

12

9

CN4302
UNREG

SH 3.1V
CN8301

IC4302

8

1•
2

FOR JIG

VCC-ZOOM

SH 3.1V

05

CLV BOARD

REC BOARD

(SEE PAGE 4-75)

(SEE PAGE 4-79)
CN5902

CN5803
TO MAIN BOARD
CN5002
(SEE PAGE 3-30)

R

MH-V
4.95V (DRIVE)

MH-V

47
•
49

4.95V

48

8•
9
10

IC5901
4.95V

IC5801
IC5803
A2.85V (DRIVE)
12

CN5801

A2.85V

10

VCC
MOTOR FLEXIBLE BOARD

IC5802
IC5807
IC5851
24
13V
UNREG

3-31

A2.85VSL

9

13V

13
•
15

UNREG

1
8

VVDD (12V)
GRT (12V)

VF LCD
CN BOARD
LCD4701

IC4501

IC101
–6.5V

INVERTER TRANS
T4701

IC4601

IC4502

IC002
IC102
IC103
IC201
SE001
SE201

IC105

CN4701
2•
4

CN4702
EVF 12V

MF LED 17

1.9V

CN4601

7•
8

BACK LIGHT
ND4701

IC5804
IC5805
IC5806
IC5808

3-32 E

DCM-M1

SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520

(For printed wiring boards)
• b: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
• Through hole is omitted.
• Circled numbers refer to waveforms.
• There are few cases that the part printed on diagram
isn’t mounted in this model.
• Chip parts.
Transistor
6 5 4 4 5 6

C

B

E

Diode
4 5

1

3

2

1 2 3 3 2 1 3 2 1 5 4 3

2

3

1 2

3

1 2

1

• Lead Layouts

surface

(Measuring conditions voltage and waveform)
MD1 PB :
• Voltages are dc between measurement point.
• Readings are taken when playing CD reference disc.
MD2 REC/PB :
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input impedance
of VOM used.)
1. Connection
Pattern box

Kinds of capacitor
Temperature characteristics
External dimensions (mm)

Front side of the lens

L = About 90 cm

2. Adjust the distance so that the output waveform of Fig.
a and the Fig. b can be obtain.

A B

Red
Blue

A=B

B A

Fig. a (Video output terminal output waveform)

Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro
spécifié.

Color bar chart
picture frame
Yellow
Cyan
Green
White
Magenta
Red
Blue

Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.

H
White
Magenta

• The voltage and waveform of CSP (chip size package) cannot be measured, because its lead layout is different form
that of conventional IC.

L

Cyan
Green

• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT → EDIT
PB/XREC → PB/REC
• 2: non flammable resistor
• 1: fusible resistor
• C: panel designation
• U : B+ Line
• V : B– Line
• C: adjustment for repair.
• Circled numbers refer to waveforms.

CSP (chip size package)

Yellow

Lead layout of conventional IC

Monitor TV
picture frame

When indicating parts by reference number, please
include the board name.
Fig.b (Picture on monitor TV)

4-1

4-2

DCM-M1

DCM-M1
4-1. FRAME SCHEMATIC DIAGRAM

FRAME
4-5

4-6

4-7

4-8

DCM-M1

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

• For Printed Wiring Board.
• There are few cases that the part isn't mounted in this model
is printed on this diagram.
• Chip transistor
4

1

R226

30

LND202

C206

16

D201
C202

R207

Q203 R202

R205
R201

C218

R223

L202

C201
R212
R216

R214

C205
7

C222

R219

1

C207

R218

R217

15

IC201

C217

R225

Q201

C220

R222

B

C216

C215

C214

A

L201

1 2 3

C213

FB201

C211

IC202

R211

Q204

E

R213 C204 R204 Q202

R209

C210 R224
R206

BB

C221

B

VC-216 BOARD (SIDE B)

VC-216 BOARD (SIDE B)

8

14

B

C219
SE201
(PITCH SENSOR)

C132
C133

E

05

4

IC103
8

1

C116

R013

CN101

48

C141

R103

IC106

C107

C101 R104

1-673-65025

51
26

50

R110

R113 R124
R126
R120
R111
R112
R121

FB101

2

3

4

5

6

7

8

05

8

7

6

5

4

1

2
37
36

25

11

R127

X102

E

VC-216 board
LENS MOTOR DRIVE,
CCD IMAGER,
CAMERA SIGNAL PROCESS

1

D

R131
IC101

R102

C102

39

40

C137

L104

R129

R132

R133
R134
1

C104

11

C139
76
75

100
1

C140

C119

1-673-650-

C138

C117

24

L002

C

R128
R130

C136

X101

12
13

C106

C024

5

LND101

R136

R125

R114 4
R106
C121

R105

FB102

C013

R101

10

R016

8

C011

R008

C023

SE001
YAW
SENSOR

1

Q001
C004

14

R007
R009

R005

C115

11

IC002

1

R122

R119 C143 L103

C134

D-4
E-4

FB103
5

C007

C014

20

C105
C103

R123 R118 C131

C135

25
24

C018
R012

R014
C010

C020

51

76

C110

C022

C021

C127
75

50

12
13

C003

D-8
B-7

L001

D101

C019

SE001

7

C009

IC105
IC102

C015

IC001

1

C012

37
36

R015
C016

C002

48
1

D

R011

R010
C111

C008

100

26

C124

C001

1

C017

Q102

25

IC104
3

D102

LND102

Q103

Q101

C130

FB105

R109

Q104

R138

C112

C

R137

R117

C142 R135

C129

R108

LND201

C108

SE001
SE201

R208

R215 R210

1

R220

C114

D-7
D-8
D-8
C-8
C-8
C-8
E-4
E-4
E-4
E-3
E-3
E-3
C-4
C-3
A-8
A-8
A-8
A-8
A-8
A-8
A-8
A-8
B-8
B-8
A-8
A-8
B-8
A-8
B-6
B-8

24

C109

R005
R007
R009
R010
R011
R015
R107
R115
R116
R118
R119
R123
R135
R138
R203
R206
R208
R209
R210
R211
R213
R215
R218
R219
R220
R221
R222
R224
R225
R226

CN201

C113

D-7
C-4
C-4
C-4
C-4
A-8
A-8

A

C123
C122
C120
C118

Q001
Q101
Q102
Q103
Q104
Q202
Q204

C212 C203
R221

BB

IC102
IC103

D-7
E-5
E-3

L101

E-4
E-4
C-3

R203
L001
L101
L103

5

C208

R107

A-7

FB103
FB104
FB105

D-3
B-8

R115

CN201

IC105
IC201

C128
C125 C126

D-7
D-7
D-6
D-7
D-7
D-8
D-7
D-8
C-8
C-8
C-8
E-5
D-5
D-6
C-5
D-5
D-5
D-5
D-5
E-5
D-5
D-5
D-4
C-4
D-4
C-4
D-4
D-4
C-3
C-3
E-3
E-3
E-3
E-3
E-3
C-4
E-3
A-8
A-8
B-8
A-8
A-8
A-8
B-8
A-6

FB104
R116

C001
C002
C003
C004
C007
C008
C009
C012
C015
C016
C022
C108
C109
C110
C111
C112
C113
C114
C115
C116
C118
C120
C123
C124
C125
C126
C127
C128
C129
C130
C131
C132
C133
C134
C135
C142
C143
C203
C204
C207
C208
C210
C212
C217
C221

C

L203

VC-216 BOARD (SIDE A)

VC-216 BOARD (SIDE A)

C209

VC-216 (LENS MOTOR DRIVE, CCD IMAGER, CAMERA SIGNAL PROCESS) PRINTED WIRING BOARD
– Ref. No.: VC-216 board; 20,000 series –

3

2

1

D-1

R008
R012
R013
R014
R016
R101
R102
R103
R104
R105
R106
R108
R109
R110
R111
R112
R113
R117
R120
R121
R122
R124
R125
R126
R127
R128
R129
R130
R131
R132
R133
R134
R136
R137
R201
R202
R205
R207
R212
R214
R216
R217
R223

D-6
D-8
D-8
D-8
D-8
D-5
D-5
D-5
E-4
D-5
C-4
C-4
C-4
E-4
E-4
E-4
E-4
C-4
E-4
E-4
E-3
E-3
C-3
E-3
E-3
C-3
C-3
C-3
D-2
C-2
D-2
D-2
C-3
C-5
B-7
B-7
A-6
B-7
B-8
B-8
B-8
B-8
B-7

D101
D201

C-4
B-7

X101
X102

C-4
E-3

FB101
FB102
FB201

E-4
D-5
A-8

IC002
IC101
IC104
IC106
IC202

D-8
D-4
C-4
D-3
A-8

L002
L104
L201
L202
L203

E-6
C-4
B-6
B-7
B-6

Q201
Q203

A-6
B-7

C010
C011
C013
C014
C017
C018
C019
C020
C021
C023
C024
C101
C102
C103
C104
C105
C106
C107
C117
C119
C121
C136
C137
C138
C139
C140
C141
C201
C202
C205
C206
C209
C211
C213
C214
C215
C216
C218
C219
C220
C222

D-8
D-6
D-8
D-8
D-8
C-8
C-8
E-8
E-8
D-8
D-6
E-5
E-5
D-5
E-4
E-5
D-5
E-4
D-4
C-5
C-4
C-3
C-3
C-3
C-2
C-2
D-2
B-8
B-7
B-8
B-8
A-8
A-8
A-6
A-8
A-6
A-8
B-7
B-7
B-7
B-7

CN101

REC board
OVER WRITE
HEAD DRIVE

CLV board
(MD MOTOR DRIVE)

4-12

LENS MOTOR DRIVE, CCD IMAGER, CAMERA SIGNAL PROCESS
4-9

4-10

4-11

VC-216

DCM-M1

VC-216 (LENS MOTOR DRIVE, CCD IMAGER) SCHEMATIC DIAGRAM

• See page 4-9 for VC-216 printed wiring board.

• See page 4-133 for waveforms.

4-13

LENS MOTOR DRIVE, CCD IMAGER
VC-216 (1/3)

VC-216 (2/3)

4-14

4-15

4-16

VC-216 (CAMERA SIGNAL PROCESS) SCHEMATIC DIAGRAM

• See page 4-9 for VC-216 printed wiring board.

• See page 4-133 for waveforms.

DCM-M1

CAMERA SIGNAL PROCESS
4-17

4-18

4-19

VC-216 (3/3)

DCM-M1

DCM-M1

MAIN (AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER, RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR,
SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR) PRINTED WIRING BOARD
– Ref. No.: MAIN board; 10,000 series –

MAIN BOARD (SIDE A)

H

2

1

7

4-23

2

C9121

R9128

C9113

R9136

C9116

R9137

R9129

R9132

R3009
R1031

C8127

C8114

C9129

R9131

C9128

R8111 R8121

C8106
R8102

C8109

R3018

R3019

R4015
R4014

C3013

4

R3015

R3014

Q3004

R3013

C1010
R1004

R1008
R1010

C1011

R1009
R1012

L3001

R2008

C2011

R1003

R1014

C1006

R1007
IC3001

C2006
R3001

C3011

R2004

1

30

C3001
C2004

C3003

C1004
C2003

C1003

C3015
C3019

R1019
R1020

R1032

C3017

C3002
C3012

C3021

R2019
R2020

C1014

R2021

R1005

R2007

R2003

R1021

15

1
CN3001
C2002

R1001

4
R3030

R2002

C1002

R1002

C3014

C3016

C1016

R2001

C2005

14

FB8022

1

11

6

CN8006

29

3

C1007
C1008

R1006

R2005
R2032

C3023

C2014

C1019

R2010

C1015

R2014

R1017

R1018

R2017

R2018
C2015

C2010

C3033

C3032

R1023

C1018

R1028

R1029

R2012 R2009
C3005

C3025

C3026

R4013
R2027
R1027

R2023

16
R2006

CN3002

1

C1009

1-672-520-

30

CN4312

1

R4022

C3007
FB8021

IC8027

1

C3050

R4026
D4001

C1013

C1005

R4027
D4002

C4024

R9909

C4025
R4030

8

4

4

CN8003

14

1

D9904

1

4

C3006

C2016

C3051

1

R1015

37
36

IC4006

IC4007

5

IC4008

R1011

C2008

C3020

R2016

R2011

C2007

IC3004

R1024

5

4

C1012

R1016

Q3003

C2009

1

R2022

13

C2018

L3006

8

8

C3030

C4027

IC8026

5

L3003

8

R8937

R4024

C1020

C3029

4
3

C4023

C5407

5
1

R2028

C4026

R1030

5

1
48

24
25

Q3001

R1013

8

IC3002

12
13

C2019

R2029

C2020

R2024

C3010

C3009

24

12

4
3

IC3005

IC3007

C1022

5
1

R2013

C2012

R3002

R2030

8

C3027

C2013
C3004

1

R3004 C3048 R3005

R2015

C2017

C3046

R5413

5

C8072

C8071

Q8006

1

C3053

D3009

C2022

IC5407

R8932

6

R8912 R8933

R8936
D8005

C8075

Q8011

R8934

1

R8908

C8077

R8935

9

D8004

C8078

8

TP5401 TP5403

4

R5414

C8074

IC5601

Q5602

4

C5412

16
C8073

1

1

C2021

IC3009
C3042

R5408

X5401

R5402
R5401

C8079

IC5401

5
IC5405

C5411

R8098

G

4
3

8

L3002

R3007 C3031 C3022

R2025

R5418 C5404

IC5404

C5402

5
1

R4023

R3006

4

C3008

R5422 R5421

C5401

C5403

R1025

C1021

IC5408

1

Q3002
L8103

R1022
C1017

5

Q4007

C3035
C3034

C3045

C3018

8

R8128

C3024

C3055

C3043
R5424

TP5422

C3044

TP5423

C5413

C5415

R5403

R5406

R5404

R5412

R5405

R5407

R5411

TP5404

C8126

C3047

R4018

17

Q4006

R4010

R8123

TP5424

05

R4016
R4017

C4002

C4001

Q4002

R4021

16

Q4005

R4005

R1026 R3022 R2026

C5608

L5603

C5607

R8126

7

C5408

2

Q4001

L4002

L4001

8

1

L5601

C5405

MAIN board
AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER,
RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR,
SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR

C8105

C8107

R8105

C8104

R8127

C8103

40

2

R8103

R8104
R8106

C8108

C8110

R8107

R8101

R8114

L8101

R8108

C8120

C5503

C5603

C8102
IC5501

L5604

CN8101

R9906

R8112

IC8101

R8116

R8125

32

14

R5410
TP5421

1

R9135

R8130

R8110

C8101
D9903

C8119

1

4

39

1

C5421

IC5205

D5601

CN5002

F

R5409

R8079 FB8017

C8122

R8118

R8122

C5424

L5403

C5417

L5401

C5422

C5418

C5423

R8129

R5417

C5406

3
2

R8078 FB8016

FB8020

R8080 FB8018

R8120

R5416

C8111

R5425

R5419

R8109

R5420

5

1

C8118

Q5201

C5416

8

R8077 FB8015

R8082

R5206

IC8104

4
1

60
FB8019

L3005

POWER board
(DC/DC CONVERTER)

C9120

R3010
R2031

59

C8115

R8113 R8115

C8116

R8081

36

C5614

CN8002

1

R8117 R8119

C8117

C5605

IC5406

C3037

C3039 C3041
R3016

C8130

L5402
C5202

C5414

C5203

R5204

R5203

C8123

R5426
R5429

7

R8075 FB8013

IC5403

X5403

C5208 C5212

L5602

R8072 FB8010

C5204

C5611

R5428

C9122

R8070 FB8008
R8071 FB8009

L5608

C5604

C5606

CN8007

IC8102

R8074 FB8012

R5319

19

L9104

R8073 FB8011

R5216 R5217

Q5202

R5207 R5208

4
3

1

R8068 FB8006

1

C5206 C5207

5
1

L5605

L5606

Q5102

C5107

R5106
L5001

C5315
C5319

IC5303

C5311

IC5302

8

R5205

2

R8067 FB8005

L8104

L9105

R5423

32

IC8103

IC5201

C5205

1

R5427

R8064 FB8002

R8066 FB8004

IC5602

50

R8063 FB8001

R8069 FB8007

4

L5610

49

2

R8076 FB8014

5

18

E

1

CN4511
Q9113

R8065 FB8003

R8124

VF board
(EVF)

R9139

C9112

C8112

C5302

TP5407

C3038

R3011
R3023

C3028

C3036

L3004
L8102

C8121

3 4

R8208

R9127

C8204
C8208

C8113

C8129

C9130

C8069

IC8202

R9134

27

26

Q9117

L8004

R5415
C9131

C5104
R5113

25

R5112

C5103

24

R5201

C5201

R5212

TP5408

6 IC9104 4
1
3

4

1
R9905

1 6

C8211
R8204

C9101

R9143

C9117

R9148

R8920

R9155

Q9115

R8922

TP5409

BL board
(EVF BACK LIGHT)

R9121

5

C5501

R5107

R5313

4
3

C5609
L5607

C5307

C5309

8

R8921

1

C5420

C5101

C5011

C5308

C5310

5
1

C5318

Q5204

3

R5214

1

C5313

X5301

L5301

L8003

IC5003

R5202

R5310
C5610

R5315

TP5015

Q5203

R5215

C5025

C5014

R5020

4

5

C5317 R5314

D

R9122

C3040

Q9116
IC5102

R5307

R5309

R5312

IC5301

C8070

8

C5105

C5210

C5106

R5305

C5316

R5311

C5303

20

4

R5105

C5314

R5306

C5312

C5304
R5302

AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER, RF AMP/DRIVE, DIGITAL
SIGNAL PROCESSOR, SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR
4-22

C8035

R5308
R5210 R5209 R5213

R5103 R5101

R5102 R5104

R5010

Q5004
R5016

R5021

R5303

5

R5304 C5306

4

Q5005

C5305

C

C5102

2

9

Q5101

C5010

Q5003
C5002

8
IC5005

R5014

C5012

CSP (chip size package)

1

C5008 R5017

R5029

L5002

C5020
R5013

C5009

C5021

R5003

R5027
C5026

16
17

L5101

TP5010 TP5014
C5055

C5022

C5027

R5061

R5018

R5024

C5017

C5001 R5011

B

R5022

C5015

37
36

24
25

4-21

MAIN

Q9125

3

R8919

2

C9123

R9150

C9118

1

C5016

IC5002

R5028

Lead layout of conventional IC

Q9126

R5023

surface

• Lead Layouts

FL5101

Q5002
R5009

C5013

R9153

R5211 C5209

R5026

48

1

12
13

C5018

4

R9156

R5025

1 2 3 5 4 3

5

C8128

2

70

TP5001

C5006

R5060

E

R5004

C5007

R5019

B

CN8001

5

1

FB3001

CN9101

R5111

2

L8202

Q5001

32

R5316

D-1
G-2
D-4

A

2

R5317

X5301
X5401
X5403

6 5 4 1

C

R5015

H-2
G-3
B-3
A-3
A-6
H-3
H-3
G-3
H-3
G-3
G-3
G-3
A-7
B-7
A-8
B-7
A-4
B-8
B-7
B-7
A-8
A-7
B-7
A-4
A-4
A-3
A-3
A-3
A-3
A-2
B-6
D-7
G-1

C5003

R8910
R8912
R8915
R8919
R8921
R8931
R8932
R8933
R8934
R8935
R8936
R8937
R9121
R9127
R9128
R9129
R9130
R9132
R9134
R9135
R9136
R9137
R9139
R9143
R9148
R9150
R9153
R9155
R9156
R9904
R9905
R9906
R9910

C5410

G-8
H-8
F-8
F-8
F-8
F-8
F-8
F-8
F-8
F-8
F-8
F-8
F-8
F-8
F-7
G-6
F-7
G-7
G-7
G-6
G-6
G-5
F-5
F-5
G-6
G-6
G-6
G-5
F-8
G-8
H-8
G-8
G-8
F-8
F-8
G-8
F-8
F-8
F-8
F-8
F-8
F-8
F-8
E-7
G-6
F-7
G-7
G-7
G-6
G-6
G-5
F-5

D-3
C-2
D-2
C-2
C-2
D-2
C-2
D-1
D-1
G-1
G-1
F-3
F-3
F-2
F-3
F-2
G-3
F-2
F-2
F-2
F-2
F-4
G-4
D-4
D-4
G-3
D-4
D-4
G-2
G-2
B-4
F-3
D-4
E-2
E-2
E-2
E-2
B-8
B-8
B-8
B-8
B-8
B-8
B-8
C-8
C-8
C-8
C-8
C-8
C-8
C-8
C-8
C-8
C-8
C-8
C-7
C-7
G-2
D-7
E-7
E-7
E-7
E-6
E-7
E-6
E-6
D-6
D-6
C-8
D-6
C-8
D-6
C-8
D-6
C-8
D-6
C-8
D-6
C-8
D-6
D-5
F-5
E-6
D-7
D-7
B-6
G-3
G-2

C5409

F-8
E-6
H-5
A-6
F-5
H-5
E-5
E-5
C-3
B-1
B-3
D-1
D-4
C-3
D-4
E-3
D-3
F-3
F-3
D-2
D-2
D-2
E-1
B-4
B-4
D-7
A-6

R1001
R1002
R1003
R1004
R1005
R1006
R1007
R1008
R1009
R1010
R1011
R1012
R1013
R1014
R1015
R1016
R1017
R1019
R1021
R1022
R1023
R1024
R1025
R1026
R1027
R1028
R1029
R1030
R1032
R2001
R2002
R2003
R2004
R2005
R2006
R2007
R2008
R2009
R2010
R2011
R2012
R2013
R2014
R2015
R2016
R2017
R2019
R2021
R2022
R2023
R2024
R2025

R5308
R5309
R5310
R5311
R5312
R5313
R5314
R5316
R5318
R5401
R5402
R5403
R5404
R5405
R5406
R5407
R5408
R5409
R5410
R5411
R5412
R5413
R5414
R5416
R5417
R5418
R5419
R5420
R5421
R5422
R5423
R5424
R5425
R5426
R5427
R5428
R5429
R8063
R8064
R8065
R8066
R8067
R8068
R8069
R8070
R8071
R8072
R8073
R8074
R8075
R8076
R8077
R8078
R8079
R8080
R8081
R8082
R8098
R8101
R8102
R8103
R8104
R8105
R8106
R8107
R8108
R8109
R8110
R8111
R8112
R8113
R8114
R8115
R8116
R8117
R8118
R8119
R8120
R8121
R8122
R8125
R8126
R8127
R8129
R8130
R8208
R8908
R8909

R8909

L3001
L3002
L3003
L3004
L3005
L3006
L4001
L4002
L5001
L5002
L5101
L5301
L5401
L5402
L5403
L5601
L5602
L5603
L5604
L5605
L5606
L5607
L5610
L8003
L8004
L8101
L8102

G-8
F-8
F-7
F-7
F-6
A-6
G-4
G-5
G-4
G-4
B-1
B-2
B-2
B-4
C-3
D-3
C-2
D-2
C-3
G-1
C-4
F-3
G-3
F-2
G-4
F-3
E-4
G-2
E-2
G-3
H-3
D-5
B-6
B-5
E-5
B-5
A-7

F-8
F-8
E-7
F-8
E-6
E-6
E-6
E-6
F-6
A-2
A-2
B-2
B-2
B-2
B-2
C-3
C-3
C-3
B-3
B-3
G-1
G-3
G-3
B-8
A-7
B-7
A-8
A-3
A-3

F-5
G-6
G-6
G-6
G-5
G-8
G-8
F-6
E-8
E-8
F-5
A-7
A-7
A-7
F-8
F-8
F-8
A-7
E-7
E-7
F-5
A-7
E-6
E-6
E-6
E-6
E-6
E-6
E-6
F-6
F-5
F-6
H-5
H-4
A-1
C-2
A-2
B-2
B-2
B-2
B-1
C-1
C-1
B-2
B-2
B-2
B-2
B-2
B-1
B-2
B-1
A-1
B-1
B-1
B-1
B-1
B-1
B-2
B-2
B-2
B-2
B-2
C-3
C-3
B-3
B-3
C-3
C-3
C-3
C-3
C-3
C-3
D-3
C-3
D-3
D-3
D-3
B-3
B-3
D-3
C-3
C-1
C-1
C-2
C-2
C-2
C-2
C-2

R5318

IC3001
IC3002
IC3004
IC3005
IC3007
IC3008
IC3009
IC4006
IC4007
IC4008
IC5002
IC5003
IC5005
IC5102
IC5201
IC5205
IC5301
IC5302
IC5303
IC5401
IC5403
IC5404
IC5405
IC5406
IC5407
IC5408
IC5501
IC5601
IC5602
IC8026
IC8027
IC8101
IC8102
IC8103
IC8104
IC8202
IC9104

Q3004
Q3001
Q3002
Q3003
Q4001
Q4002
Q4005
Q4006
Q4007
Q5001
Q5002
Q5003
Q5004
Q5005
Q5101
Q5102
Q5201
Q5202
Q5203
Q5204
Q5602
Q8006
Q8011
Q9113
Q9115
Q9116
Q9117
Q9125
Q9126

R2026
R2027
R2028
R2029
R2030
R2032
R3001
R3002
R3004
R3005
R3006
R3009
R3010
R3011
R3013
R3014
R3015
R3016
R3018
R3019
R3022
R3023
R4005
R4010
R4013
R4014
R4015
R4016
R4017
R4018
R4021
R4022
R4026
R4030
R5001
R5003
R5004
R5009
R5010
R5011
R5013
R5014
R5015
R5016
R5017
R5018
R5020
R5021
R5022
R5023
R5024
R5025
R5026
R5027
R5028
R5060
R5061
R5101
R5102
R5103
R5104
R5105
R5106
R5107
R5112
R5113
R5201
R5202
R5203
R5204
R5205
R5206
R5207
R5208
R5209
R5210
R5211
R5214
R5215
R5216
R5217
R5301
R5302
R5303
R5304
R5305
R5306
R5307

C5023

A-2

E-6
B-5
B-5
B-8
B-4

C8076

A-6
A-6
B-8
B-8

FL5101

L8103
L8104
L8202
L9104
L9105

R8910

FB3001
FB3002
FB8001
FB8002

H-5
E-3
H-3

B-8
B-8
B-8
B-8
B-8
C-8
C-8
C-8
C-8
C-8
C-8
C-8
C-8
C-8
C-8
C-8
C-7
C-7
H-6
H-6

8
IC3008

FB3002

R8931

D4001
D5601
D8005

G-8
H-3
H-5
B-8
A-2
F-1
A-5
C-8
H-2
H-6
B-7
D-8
A-4

FB8003
FB8004
FB8005
FB8006
FB8007
FB8008
FB8009
FB8010
FB8011
FB8012
FB8013
FB8014
FB8015
FB8016
FB8017
FB8018
FB8019
FB8020
FB8021
FB8022

C5601

CN3001
CN3002
CN4312
CN4511
CN5001
CN5002
CN8001
CN8002
CN8003
CN8006
CN8007
CN8101
CN9101

E-3
D-3
E-3
D-2
F-2
F-3
D-2
D-2
F-2
B-3
B-4
B-4
G-3
G-3
G-2
G-2
H-2
H-3
G-2
H-2
G-2
D-7
E-5
E-5
E-6
E-6
D-7
E-6
E-6
E-7
E-6
C-6
B-6
B-5
D-7
C-6
C-5
C-5
C-5
D-5
D-5
A-6
E-5
E-6
D-7
A-6
B-5
C-5
B-5
B-5
B-6
A-4
B-7
A-8
A-7
A-4
B-3
A-7
A-7
B-8
A-4
B-8
B-8
B-4
B-4

C5004

C5603
C5604
C5605
C5606
C5607
C5608
C5609
C5610
C5614
C8035
C8069
C8070
C8071
C8072
C8073
C8074
C8075
C8076
C8077
C8078
C8079
C8101
C8102
C8103
C8104
C8105
C8106
C8107
C8108
C8109
C8110
C8111
C8112
C8113
C8114
C8115
C8116
C8117
C8118
C8119
C8120
C8121
C8123
C8126
C8127
C8128
C8129
C8130
C8204
C8208
C8211
C9101
C9112
C9113
C9116
C9117
C9118
C9120
C9121
C9122
C9123
C9128
C9129
C9130
C9131

R9910

G-4
H-5
G-4
G-4
C-2
B-2
A-1
B-1
A-1
A-2
A-2
B-2
B-1
C-3
C-1
B-2
B-2
B-2
B-2
B-2
A-1
B-1
B-1
B-1
B-1
B-1
B-2
B-1
B-2
B-2
B-3
B-2
B-3
B-3
B-3
B-2
C-3
C-3
C-3
C-3
C-3
D-3
C-3
D-3
D-3
D-3
C-1
D-1
C-1
C-1
C-1
C-2
D-2
C-2
D-2
C-2
D-2
C-2
C-2
C-2
C-2
C-2
C-2
D-2
C-2
G-1
G-1
G-1
F-3
F-2
F-2
G-4
F-2
G-2
F-2
G-2
G-3
F-3
C-3
F-3
D-4
D-4
B-3
D-4
D-4
C-3
E-3
G-1

19

1

1

CN5001

C5024

C4023
C4024
C4026
C4027
C5001
C5002
C5003
C5004
C5005
C5006
C5007
C5008
C5009
C5011
C5012
C5013
C5014
C5015
C5016
C5017
C5018
C5020
C5021
C5022
C5023
C5024
C5025
C5026
C5027
C5055
C5101
C5102
C5103
C5104
C5105
C5106
C5201
C5202
C5203
C5204
C5205
C5206
C5207
C5208
C5209
C5212
C5301
C5302
C5303
C5304
C5305
C5306
C5307
C5308
C5309
C5310
C5311
C5312
C5313
C5314
C5315
C5316
C5317
C5318
C5319
C5401
C5402
C5403
C5404
C5405
C5406
C5407
C5408
C5409
C5410
C5411
C5412
C5413
C5414
C5415
C5417
C5418
C5420
C5421
C5424
C5501
C5503
C5601

69

R5301

G-8
G-8
H-8
F-8
F-8
F-8
F-8
F-8
F-8
F-7
G-7
G-7
F-7
G-7
G-6
G-6
G-6
G-5
F-5
G-5
G-8
G-8
H-8
G-8
F-8
F-8
F-8
F-8
F-8
F-7
F-7
G-7
F-7
G-7
G-6
G-6
F-6
G-5
F-5
G-5
G-8
G-8
G-8
F-7
F-8
F-8
H-5
F-5
G-8
G-7
G-7
G-7
G-7
G-8
G-5
G-7
G-6
F-6
F-6
E-6
E-6
F-7
A-6
H-5
F-6
F-6
F-6
F-6
F-6
A-6
A-7
A-7
A-7
A-6
A-7
G-4
F-4
F-5
F-5
F-5
E-6
A-5
G-6
H-6
E-7
F-5
E-5
E-5

TP8047

1

C5301

C1003
C1004
C1005
C1006
C1007
C1008
C1009
C1010
C1011
C1012
C1013
C1014
C1015
C1016
C1017
C1018
C1019
C1020
C1021
C1022
C2003
C2004
C2005
C2006
C2007
C2008
C2009
C2010
C2011
C2012
C2013
C2014
C2015
C2016
C2017
C2018
C2019
C2020
C2021
C2022
C3001
C3002
C3003
C3004
C3005
C3006
C3007
C3008
C3011
C3013
C3014
C3015
C3016
C3017
C3018
C3019
C3021
C3022
C3023
C3025
C3026
C3027
C3028
C3030
C3031
C3032
C3033
C3034
C3035
C3036
C3037
C3038
C3039
C3040
C3041
C3042
C3043
C3044
C3045
C3046
C3047
C3049
C3050
C3051
C3053
C3055
C4001
C4002

33

R5001

C5005

MAIN BOARD (SIDE A)

R9130

R9904

TP5002
R5002

C3049

• For Printed Wiring Board.
• There are few cases that the part isn't mounted in this model
is printed on this diagram.
• Chip transistor

5

6
4-24

7

8

DCM-M1

R8517

R8514

R8519

R8516

R8515

R5078
R5039

R5040

R5042

R8508

R8509

R8510

C8512

R5005
R5012
R5030

R5601
C4005

C4020
C4022

R4002

Q4004

R4007

C4010
C4011

TP4002

8

C4018

C4014

R4019

C4016

5

C4015
R4006

Q4003

IC4005

6 1
R4008

1

4

4
3

C4017

R9908

C4019

R4012

6
1

4 3
FL4002

14

4

G

L4003

C4003

C4006

C4007
C4008

R4001

C4013

TP1001

1

5

4 3

C4021

R4004 C4009

R9126
C9108

R9107

R9115

Q9105

IC4001

IC4003

R9109

C9103

D5001

C5602

F

5

6 1

TP2001

IC4004
R9157

C5028

C5056

R5034
C5029
C5030
C5031

R5076

C5019

R5006

R5051

TP5405

1

C4012

R4009

R9101

4-25

6 1

S8003
OPEN/CLOSE
DETECT

Q9108

Q9102

6

4 3

FL4001

CN4313

7

E

C8621
R4003

C8620
R9108

R9113

S8003

C9119

8

3 4
IC5015

TP4001

IC4002

R9111

05

1 5

R5059

R4011

Q9101

C9114

R9105

C9104
R9123

5

R5602

C8605
C8603
R9120

C9106

R9106
R9124
R9114

6

4

C9115

C9105
R9102

C9102

44

43

C9107

Q9107
Q9110

R9117

R9112

Q9111

C9110

R9110
Q9104

R9118

R9154
R9116 R9125

R9103

R9144

S8002

TP5402

1
IC9103

Q9103

TP9113

4

R5058

IC5603

TP5414

IC5402

C8618

3

L9102

Q9112

R9104

R9147

C9111

C9109

TP1002

8

C4004

R9119

L9103

C3052

5

1

D5602

3

4

4
3

C8604

L8601

4
TP2002

R8521

C5613

C8607

C8703

C8608

R8601

C8609

R8602

C8702

C8606

C5419

5
1

C8613

C8617

R8502

R8501

R5605

IC8601

C8616

4

S8001

C5052

C8610

C8615

R8503

A

TP5417

C8614

IC5013

S8002
HALF LOCK
DETECT

C8624

C8601

8

5

8
1

D

R5607

R5606

IC8602

IC3003

C

K

Q5603

C8718

1

8

Q5601

C5615

C8612

1
IC5008

C8623

C8602

TP8601

R8505

C8502

C8622

86

C8619

C8709

C8611

R8050

C8501

1

L8603

L8701

C5054

C8082

C8507

R8603

L8602

R8504

R8506

IC5014

R8532

C8716

L8702

R5077

R8051

Q8001

C8503

R8525

R8507

C8510

R8513

C8704

C8714

C8701

C8715

IC8703

4
5

TP8502

R8530

R8512

C5032

C5051

R8528
R8526 R8527

8

S8001
OPEN/CLOSE
DETECT

C8508

IC8010

IC5007

5

U8001
(LITHIUM SECONDARY BATTERY)

TP8501 TP8503

IC8501

IC8701

C8717

R8052
D8002

IC8011

R8055
C8055

R8529

C8504

U8001

C8708

C8713

4
3

C8511

R8524

Q8005

4
3

C8706

C8712

IC8009

C8037

R8090

5
1

X8501

C8505

R8511

C8029

C8705

C8711

TP8108

4

1

3
2

1

R8522

C8023
R8088

C8707

TP8106

4
1

C8030

C8710

R8913

IC8023

TP8107

R8045

C8031

5

8

X8001

C8024
R8083

R8038

R8041 C8025

R8043

R8047

R8089

R8093

1
5

3
4
C8064

C8020

6

5
R8096

14

IC8008

R8094

IC8702

IC5004

5
1

TP8505

10

1

R8095

IC8024

C5036
IC5009

R8520
TP8504

C8063

C8021

TP8020

7

C8016

R8531

D8001

R8042

L8001
C8067

R8044 C8026

C8001

C8027

R8905 R8099

C8028

C8003 R8904

8

4

C5040

1

4

C5033

C8018 C8017

C8022

X8002

R8006

R8002 R8001

R8009 R8004

R9903

TP8114

R8007

R8010 R8003

TP8029 TP8109

R8011

R8008 R8005

TP8028
TP8102

1

R8911

TP8026 TP8027

1

C8068

TP8101
TP8103

8

R5049 R5050
C5038

1
5

C5037

C8066

C8004

Q8004

IC5010

3
4

R8523

C8015 R8035

4

R8032
R8026

R5057

C5049

R8027

R5055

B

TP5003

C5050

R8024

3

R8034

R5056

R5008

8 5
IC5006
1 4

C5048

R5048

TP8045 R8018 R8025

C5046
C5039

C5043

C5047

5

Q8003

4
3

R5043

R8033

R8907 R8906

C8039

1

5

8

5
1

R5054

R5052
C5045

R5031

R8030

C8036

R8054

R8017 R8031

C5042 R5053

4
3

R5047

R8013

IC8012

4
3

5
1

R5044

R8020

C8065
IC8025

5
1

C5041

R5046

R8021

4

R5110
C5044

IC5011

R5037

R8029

X8003

TP8013
C8040

R8917

R8028

R8019

C5108
R5036

IC5012

IC8001

TP8113 TP8110

TP8112

R8023

R8037

TP8009

TP8111

Q9122

R8016

C8005

IC8002

TP8035

R8097

5

R8915

R5109
R5035
Q5010

C5035

C8014

C8006 C8007

TP8015

TP8033

R9161

C8041

TP8017
TP8036

R8022

TP8046

C8019

R9158 R9152 R9140

TP807

C8044

R8015

R8053

C8038

R8012

C8002

R9159

6 IC9102 4
1
3

C8042

R9160

TP9116

TP9112

C8057

R8040

C8012

TP8034

TP8038

Q8010

R5108

C8506

C8011

4
3

R8049

R5032 R5007

R5603

C8010

5
1

D8003

C5057

TP9110

Q8002

C8009

C8008

R8092

R8048

1

Q5009

L8501

C8034

IC8003

R8046

C9127

5

R5033 C5034

C8032

R5604

TP8019

TP8010

TP8014

C8059
IC8016

TP8018

TP8008
C9132

C9126

1

32

TP8016

R8057

3

R8916

R8036

C8033

4

D8006

R8086

TP8007

C4028

C9133

C8045

4

A

TP5016

1

8

R8914

TP8006

C8054

TP5012

TP9114

Q8007

C8062

C8080

TP8011

R8901

C8013

5

TP8039
TP8030
TP8012

IC8004

R8091

IC4009

4

TP8043

TP8023

1
5

C8056

R8062
TP8005

TP8025

TP9111

R8039
C8051

R8061

4

D8007

L8002

R8085

8

TP8032

R8087

TP8004

1

TP8041

TP8031

C4029

16

17

R9902

TP8040

TP8003 TP8001

4 1
IC8015
5 8

Q8014

R8058

TP8022

TP8002

D4003

Q8012

D9901

C4030
R4028

3
4

TP8042
TP8024

MAIN BOARD (SIDE B)

TP9104

5
TP9106

TP8044

1

R4029

TP8104

5 8 5
IC4011
4 1 4

R8902

IC4010

R8903

8

1

7

IC8014

TP5018

TP5011

TP9109

Q8008

1

R8084
R8918

Q8013

C8043

TP9115 D4004
TP8105

C8049

TP3001
TP8021

TP9107

4
3

C8053

R4031

5
1

5

TP5013

IC8020

TP9105

C8048 C8052

C4032

4
3

IC8013

IC8005
C4031

5
1

C8081

4
3

8

R8056

5
1

TP3002

TP9103

8

14

R5045

TP9108

R5038

IC8006

Q8009

TP9101

R5041

C8047

IC8007

TP9102

R9901

C8046

C8050

MAIN BOARD (SIDE B)

H

TP4003

1-672-520-

11

C3048
C3052
C4003
C4004
C4005
C4006
C4007
C4008
C4009
C4010
C4011
C4012
C4013
C4014
C4015
C4017
C4018
C4019
C4020
C4021
C4022
C4028
C4029
C4031
C4032
C5019
C5028
C5029
C5030
C5031
C5032
C5033
C5034
C5035
C5036
C5037
C5038
C5039
C5040
C5041
C5042
C5043
C5044
C5045
C5046
C5047
C5048
C5049
C5051
C5052
C5056
C5057
C5419
C5602
C5615
C8001
C8002
C8003
C8004
C8005
C8006
C8007
C8008
C8009
C8010
C8011
C8012
C8013
C8014
C8015
C8016
C8017
C8018
C8019
C8020
C8021
C8022
C8023
C8024
C8025
C8026
C8027
C8028
C8029
C8030
C8031
C8032
C8033

E-8
G-6
G-1
G-2
G-2
G-2
G-3
G-3
G-3
H-2
H-3
H-2
H-2
H-3
H-3
H-2
H-2
H-1
G-1
G-2
G-1
C-8
B-8
A-8
A-8
B-1
B-1
B-1
B-1
C-1
C-1
C-1
A-1
C-2
C-2
C-2
C-2
B-2
C-2
B-2
B-2
B-1
B-1
B-2
B-2
B-1
B-1
C-1
E-2
E-1
B-1
A-1
F-3
F-2
F-3
D-6
C-6
D-6
C-6
C-6
C-6
C-6
C-6
B-5
B-5
B-5
B-4
B-4
C-4
C-4
C-3
C-3
C-4
C-4
C-4
D-4
C-3
D-5
D-5
D-5
D-5
D-5
D-5
D-5
D-5
D-5
A-3
A-3

C8034
C8036
C8037
C8038
C8039
C8040
C8041
C8042
C8043
C8044
C8045
C8046
C8047
C8048
C8049
C8050
C8051
C8052
C8053
C8055
C8056
C8057
C8059
C8062
C8063
C8064
C8065
C8067
C8068
C8080
C8081
C8501
C8502
C8503
C8504
C8506
C8507
C8508
C8510
C8511
C8601
C8602
C8603
C8604
C8605
C8606
C8607
C8608
C8609
C8610
C8611
C8612
C8613
C8614
C8615
C8616
C8617
C8618
C8619
C8620
C8621
C8622
C8623
C8624
C8701
C8702
C8703
C8704
C8705
C8706
C8707
C8708
C8709
C8710
C8711
C8712
C8713
C8714
C8715
C8716
C8717
C8718
C9103
C9104
C9105
C9106
C9107
C9108

B-5
B-3
D-6
B-3
C-6
C-6
C-6
C-6
B-6
C-6
B-6
A-4
A-4
A-4
A-6
A-4
B-4
A-4
A-4
B-3
B-3
B-4
B-4
A-3
D-4
D-6
B-3
D-6
D-4
B-3
A-3
E-3
E-3
D-2
E-3
C-2
E-3
D-2
E-2
D-3
F-6
F-6
G-4
G-4
F-4
F-5
F-5
F-5
F-5
F-7
F-5
F-6
G-6
G-6
G-5
G-5
G-5
G-5
E-4
G-4
G-3
E-3
E-3
F-3
E-7
F-5
F-5
E-4
E-4
E-4
E-6
E-6
E-6
D-6
E-6
E-6
E-6
E-6
E-6
E-6
E-7
F-6
H-5
H-5
H-6
G-5
H-5
H-4

C9109
C9110
C9111
C9114
C9115
C9119
C9126
C9127
C9132
C9133

G-5
H-5
G-6
H-4
H-5
H-6
C-8
C-8
C-8
C-8

CN4313

H-4

D4003
D5602
D8001
D8002
D8003
D8006
D8007

B-8
E-1
D-5
B-2
B-3
C-3
A-3

FL4001
FL4002

G-3
H-3

IC3003
IC4001
IC4002
IC4003
IC4004
IC4005
IC4009
IC4010
IC4011
IC5004
IC5006
IC5007
IC5008
IC5009
IC5010
IC5011
IC5012
IC5013
IC5014
IC5015
IC5402
IC5603
IC8001
IC8002
IC8003
IC8004
IC8005
IC8006
IC8007
IC8008
IC8009
IC8010
IC8011
IC8012
IC8013
IC8015
IC8016
IC8020
IC8023
IC8024
IC8025
IC8501
IC8601
IC8602
IC8701
IC8702
IC8703
IC9102
IC9103

G-6
G-2
G-2
H-2
H-3
H-2
B-8
A-8
A-8
C-2
B-1
B-1
C-1
C-2
C-2
B-2
B-2
C-1
E-2
E-1
F-3
F-2
C-5
C-6
B-6
B-5
A-5
A-4
A-4
D-4
D-5
D-5
A-3
B-3
A-4
B-4
B-4
A-3
D-5
D-5
B-3
D-3
F-5
F-4
E-5
E-6
E-6
C-8
G-5

L4003
L8001
L8002
L8501
L8601
L8602
L8603
L8701
L8702
L9102
L9103

G-1
D-5
D-3
E-2
G-7
F-6
F-3
F-6
F-7
G-5
G-6

Q4003
Q4004

H-1
H-1

A-2
B-2
E-2
F-3
B-3
B-2
C-3
C-2
D-4
A-3
A-3
B-3
B-3
B-6
A-6
B-6
H-5
H-6
H-5
H-6
H-4
H-5
G-4
H-6
H-5
G-6
D-8

R4001
R4002
R4003
R4004
R4006
R4007
R4008
R4009
R4011
R4012
R4019
R4020
R4028
R4031
R5005
R5006
R5007
R5008
R5012
R5030
R5031
R5032
R5033
R5034
R5037
R5038
R5039
R5040
R5041
R5042
R5043
R5044
R5045
R5046
R5047
R5048
R5049
R5050
R5051
R5052
R5053
R5054
R5055
R5056
R5057
R5058
R5059
R5076
R5077
R5078
R5601
R5602
R5603
R5604
R5605
R5606
R5607
R8001
R8002
R8003

G-2
G-2
G-3
G-3
H-3
H-3
H-3
H-3
H-1
H-1
H-3
H-3
B-8
A-7
B-1
B-1
B-1
B-1
B-1
C-1
C-2
B-1
A-1
B-1
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
C-2
B-2
B-2
C-2
B-2
B-2
B-1
B-2
B-2
B-1
E-2
E-2
B-2
B-2
A-2
F-2
F-2
F-2
F-2
F-3
F-3
E-2
D-6
D-6
D-6

R8004
R8005
R8006
R8007
R8008
R8009
R8010
R8011
R8012
R8013
R8015
R8016
R8017
R8018
R8019
R8020
R8021
R8022
R8023
R8024
R8025
R8026
R8027
R8028
R8029
R8030
R8031
R8032
R8033
R8034
R8035
R8036
R8037
R8038
R8039
R8040
R8041
R8042
R8043
R8044
R8045
R8046
R8047
R8048
R8049
R8050
R8051
R8052
R8053
R8055
R8056
R8057
R8058
R8061
R8062
R8083
R8084
R8085
R8086
R8087
R8088
R8089
R8090
R8091
R8092
R8093
R8094
R8095
R8096
R8097
R8099
R8501
R8502
R8503
R8504
R8505
R8506
R8507
R8508
R8509
R8510
R8511
R8512
R8513
R8514
R8515
R8516
R8517

D-6
D-7
D-6
D-6
D-7
D-6
D-6
D-6
C-3
C-3
B-4
B-4
C-4
C-4
C-4
C-4
C-4
B-4
B-4
C-4
C-4
C-3
C-3
B-3
C-3
C-4
C-4
C-3
C-3
C-4
C-4
B-7
C-4
D-5
B-4
B-3
D-5
D-5
D-5
D-5
D-5
C-7
D-5
B-3
B-3
B-2
B-3
B-2
B-4
B-3
B-3
B-4
B-4
A-2
B-7
D-5
A-4
B-7
B-7
B-7
D-4
D-5
D-5
B-7
C-7
D-5
D-5
D-5
D-5
B-3
D-6
D-2
D-2
D-2
D-2
D-2
D-2
D-2
D-2
D-2
D-2
D-3
E-4
E-4
E-4
E-4
E-4
E-4

R8519
R8520
R8521
R8522
R8523
R8524
R8525
R8526
R8527
R8528
R8529
R8530
R8531
R8532
R8601
R8602
R8603
R8901
R8902
R8903
R8904
R8906
R8911
R8913
R8914
R8916
R8917
R8918
R9101
R9102
R9103
R9104
R9105
R9106
R9107
R9108
R9109
R9110
R9111
R9112
R9113
R9114
R9116
R9117
R9118
R9119
R9120
R9123
R9124
R9125
R9126
R9140
R9144
R9147
R9152
R9154
R9157
R9159
R9161
R9901
R9902
R9903

E-4
C-3
D-2
D-2
D-2
D-3
E-4
E-4
E-4
E-4
D-3
E-2
D-3
E-3
F-5
F-5
F-4
B-4
B-6
B-6
D-6
C-4
C-3
D-5
C-3
B-3
A-3
A-3
H-6
H-6
H-6
H-6
H-5
G-5
H-4
G-4
H-4
H-5
H-6
H-6
G-4
H-6
H-6
H-5
G-5
G-5
G-4
H-5
H-6
G-6
G-4
C-8
H-6
G-6
C-8
G-5
H-5
C-8
C-8
A-2
B-7
D-6

S8001
S8002
S8003

D-1
E-1
G-4

U8001

D-4

X8001
X8002
X8003
X8501

D-4
D-6
C-4
D-3

4-27

R4020

3

Q5009
Q5010
Q5601
Q5603
Q8001
Q8002
Q8003
Q8004
Q8005
Q8007
Q8008
Q8009
Q8010
Q8012
Q8013
Q8014
Q9101
Q9102
Q9103
Q9104
Q9105
Q9107
Q9108
Q9110
Q9111
Q9112
Q9122

2

AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER, RF AMP/DRIVE, DIGITAL
SIGNAL PROCESSOR, SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR

1
4-26

MAIN

DCM-M1

MAIN (AUDIO/VIDEO DATA CONTROL) SCHEMATIC DIAGRAM

DCM-M1

• See page 4-21 for MAIN printed wiring board.

• See page 4-133 for waveforms.

4-29

AUDIO/VIDEO DATA CONTROL
MAIN (1/8)

4-30

4-31

4-32

DCM-M1

MAIN (MPEG ENCODER/DECODER) SCHEMATIC DIAGRAM

• See page 4-21 for MAIN printed wiring board.

• See page 4-133 for waveforms.

4-37

MPEG ENCODER/DECODER
4-33

4-34

4-35

4-36

MAIN (2/8)

DCM-M1

DCM-M1
MAIN (RF AMP/DRIVE) SCHEMATIC DIAGRAM

• See page 4-21 for MAIN printed wiring board.

• See page 4-134 for waveforms.

RF AMP/DRIVE
MAIN (3/8)

4-39

4-40

4-41

4-42

MAIN (DIGITAL SIGNAL PROCESSOR) SCHEMATIC DIAGRAM

• See page 4-21 for MAIN printed wiring board.

• See page 4-134 for waveforms.

DCM-M1

4-46

DIGITAL SIGNAL PROCESSOR
4-43

4-44

4-45

MAIN (4/8)

DCM-M1

DCM-M1

MAIN (SYSTEM CONTROL) SCHEMATIC DIAGRAM

• See page 4-21 for MAIN printed wiring board.

• See page 4-133 for waveforms.

4-48

SYSTEM CONTROL
MAIN (5/8)

4-49

4-50

4-51

4-52

MAIN (VIDEO) SCHEMATIC DIAGRAM

• See page 4-21 for MAIN printed wiring board.

DCM-M1

• See pages 4-133, 134 for waveforms.

VIDEO

4-53

4-54

4-55

MAIN (6/8)

DCM-M1

MAIN (AUDIO) SCHEMATIC DIAGRAM

• See page 4-21 for MAIN printed wiring board.

• See page 4-134 for waveforms.

AUDIO

MAIN (7/8)

4-56

4-57

4-58

MAIN (SWITCHING REGULATOR) SCHEMATIC DIAGRAM

• See page 4-21 for MAIN printed wiring board.

DCM-M1

• See page 4-133 for waveforms.

SWITCHING REGULATOR
4-59

4-60

4-61

MAIN (8/8)

DCM-M1

MAIN CONTROL SWITCH UNIT, ZOOM SWITCH UNIT SCHEMATIC DIAGRAM

4-62

MAIN CONTROL SWITCH UNIT, ZOOM SWITCH UNIT
4-63

4-64

DCM-M1

UPPER CONTROL SW SUB ASSY, REMOCON RAY-CATCHER BLOCK UNIT,
LCD DETECTION SW FLEXIBLE BOARD SCHEMATIC DIAGRAM

4-67
4-65

4-66

UPPER CONTROL SW SUB ASSY, REMOCON RAY-CATCHER
BLOCK UNIT, LCD DETECTION SW FLEXIBLE BOARD

DCM-M1

CLV (MD MOTOR DRIVE) PRINTED WIRING BOARD
– Ref. No.: CLV board; 20,000 series –

CLV BOARD (SIDE A)
C5807
C5808
C5811
C5813
C5814
C5815
C5818
C5819
C5823
C5825

C-11
C-11
B-9
B-5
A-6
B-8
B-7
B-11
C-9
B-9

R5802
R5803
R5806
R5807
R5809
R5810
R5823
R5824
R5826
R5828

C-11
C-11
B-10
B-10
C-10
C-10
C-11
C-11
C-9
B-9

IC5802
IC5804
IC5805
IC5806
IC5807
IC5808

B-10
B-6
B-8
B-6
C-11
B-7

S5801
S5802
S5803
S5804

A-5
A-6
A-6
A-9

Q5821
Q5823

C-9
B-9

MD MOTOR DRIVE
CLV

4-68

4-69

4-70

DCM-M1

• For Printed Wiring Board.
• There are few cases that the part isn't mounted in this model
is printed on this diagram.
• Chip transistor
C

B

CLV BOARD (SIDE B)

4 5 6

E

3 2 1

VC-216 board
LENS MOTOR DRIVE,
CCD IMAGER,
CAMERA SIGNAL PROCESS

REC board
OVER WRITE
HEAD DRIVE

CLV board
(MD MOTOR DRIVE)

C5804
C5805
C5806
C5809
C5810
C5812
C5816
C5817
C5820
C5824
C5826
C5827
C5828
C5829
C5851
C5852
C5853
C5854

A-10
A-9
B-10
C-9
C-10
C-10
A-8
B-8
A-9
C-8
C-9
B-9
B-9
A-6
D-6
C-7
D-7
D-7

CN5801
CN5803

C-11
B-1

D5801

C-7

IC5801
IC5802
IC5803
IC5851

B-10

L5801

B-6

Q5801
Q5802
Q5803
Q5808
Q5809
Q5810
Q5811
Q5812
Q5813
Q5822
Q5824
Q5825
Q5826

B-7
A-8
A-9
D-8
C-8
C-8
C-8
B-8
B-8
C-9
C-9
B-9
B-9

R5801
R5804
R5805
R5808
R5811
R5812
R5813
R5814
R5815
R5816
R5817
R5818
R5819
R5820
R5821
R5822
R5825
R5827
R5829
R5830
R5831
R5832
R5833
R5834
R5851
R5852

A-10
A-9
C-10
C-9
A-8
A-9
C-8
C-8
C-8
C-9
B-8
B-8
A-9
B-7
A-8
A-8
E-12
D-8
C-8
B-9
B-8
B-10
B-10
C-10
D-6
D-7

S5805

E-11

SE5851

D-6

C-10
D-7

MD MOTOR DRIVE
4-71

4-72

4-73

4-74

CLV

DCM-M1
CLV (MD MOTOR DRIVE) SCHEMATIC DIAGRAM

• See page 4-68 for CLV printed wiring board.

• See page 4-134 for waveforms.

MD MOTOR DRIVE
CLV

4-75

4-76

4-77

4-78

DCM-M1

REC (OVER WRITE HEAD DRIVE) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM
– Ref. No.: REC board; 20,000 series –

• For Printed Wiring Board.
• There are few cases that the part isn't mounted in this model
is printed on this diagram.
• Chip transistor
C

B

E

VC-216 board
LENS MOTOR DRIVE,
CCD IMAGER,
CAMERA SIGNAL PROCESS

REC board
OVER WRITE
HEAD DRIVE

CLV board
(MD MOTOR DRIVE)

OVER WRITE HEAD DRIVE
4-79

4-80

4-81

4-82

REC

DCM-M1

VF (EVF) PRINTED WIRING BOARD
– Ref. No.: VF board; 20,000 series –

VF BOARD (SIDE B)

• For Printed Wiring Board.
• There are few cases that the part isn't mounted in this model
is printed on this diagram.
• Chip transistor

VF BOARD (SIDE A)
C4502
C4503
C4504
C4505
C4506
C4507
C4508
C4510
C4512
C4514
C4516
C4517
C4518
C4519
C4520
C4521
C4522
C4523
C4524
C4526
C4527
C4612
C4618
C4620
C4624
C4625

F-4
F-3
E-1
E-1
F-1
F-1
F-2
H-4
F-1
G-1
H-3
H-3
H-3
H-2
G-1
H-4
G-4
H-1
H-2
E-4
E-4
A-4
C-2
B-2
A-3
A-1

IC4501
IC4602

G-3
A-2

L4501
L4502

H-5
F-3

Q4502
Q4503
Q4504
Q4505
Q4506
Q4507

F-1
F-1
F-1
G-1
G-1
H-1

R4501
R4516
R4517
R4518
R4525
R4528
R4530
R4531
R4540
R4564
R4565
R4566
R4567
R4568
R4604
R4607
R4615
R4617
R4618
R4629
R4630
R4634

E-2
F-2
F-2
G-5
F-4
F-4
G-4
G-4
G-4
G-2
G-4
G-4
G-4
G-5
B-4
B-5
A-4
A-4
B-4
B-1
C-2
C-2

C

B

BL board
(EVF BACK LIGHT)

E

VF board
(EVF)

POWER board
(DC/DC CONVERTER)

MAIN board
AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER,
RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR,
SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR

EVF
VF

4-83

4-84

4-85

4-86

C4501
C4509
C4515
C4525
C4601
C4602
C4603
C4604
C4605
C4606
C4608
C4610
C4611
C4613
C4614
C4615
C4616
C4617
C4619
C4621
C4622

F-3
F-1
G-1
H-1
C-5
C-5
C-4
C-4
A-5
C-4
C-4
B-4
B-4
A-4
C-4
C-4
C-1
C-2
B-3
B-2
C-3

CN4501
CN4601
CN4901

F-4
A-2
H-7

D4601
D4602

A-3
C-2

IC4502
IC4601

G-4
B-4

L4503
L4601
L4602
L4603

F-4
B-3
B-3
B-1

Q4601
Q4602
Q4603

C-5
A-3
A-3

R4502
R4503
R4507
R4508
R4514
R4515
R4519
R4520
R4523
R4524
R4526
R4527
R4529
R4532
R4533
R4534
R4535
R4538
R4539
R4541
R4542
R4543
R4544
R4546
R4547
R4550
R4551
R4553
R4556
R4557
R4558
R4559
R4560
R4561
R4562
R4570
R4601
R4602
R4603
R4605
R4608
R4609
R4610
R4611
R4612
R4613
R4614
R4616
R4619
R4620
R4621
R4622
R4623
R4624
R4626
R4627
R4628
R4636

F-4
F-3
F-4
F-3
E-1
E-1
F-1
F-1
F-1
F-1
G-3
G-2
F-1
G-3
F-1
F-1
G-1
F-1
G-1
G-3
H-3
G-3
G-1
H-3
H-3
G-2
G-2
G-1
G-3
G-1
G-1
G-1
G-1
G-1
H-2
G-1
C-3
C-3
B-4
B-4
B-4
B-4
A-4
A-4
A-4
B-4
B-4
B-4
C-4
C-4
B-4
A-3
C-4
B-2
C-3
C-1
C-2
B-3

DCM-M1

VF (EVF LCD DRIVE, EVF TIMING GENERATOR) SCHEMATIC DIAGRAM

• See pages 4-133, 134, 135 for waveforms.

4-91

EVF LCD DRIVE, EVF TIMING GENERATOR
4-87

4-88

4-89

4-90

VF

DCM-M1

DCM-M1

BL (EVF BACK LIGHT) PRINTED WIRING BOARD
– Ref. No.: BL board; 20,000 series –

• For Printed Wiring Board.
• There are few cases that the part isn't mounted in this model
is printed on this diagram.
• Chip transistor
C

B

BL board
(EVF BACK LIGHT)

E

VF board
(EVF)

POWER board
(DC/DC CONVERTER)

MAIN board
AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER,
RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR,
SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR

EVF BACK LIGHT
BL

4-93

4-94

4-95

4-96

DCM-M1
BL (EVF BACK LIGHT DRIVE, EVF BACK LIGHT) SCHEMATIC DIAGRAM

Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.

Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro
spécifié.

4-100

EVF BACK LIGHT DRIVE, EVF BACK LIGHT
4-97

4-98

4-99

BL

DCM-M1

LCD (LCD) PRINTED WIRING BOARD
– Ref. No.: LCD board; 20,000 series –

• For Printed Wiring Board.
• There are few cases that the part isn't mounted in this model
is printed on this diagram.
• Chip transistor
C

B

E

LCD
LCD

4-101

4-102

4-103

4-104

LCD (LCD) SCHEMATIC DIAGRAM

• See page 4-135 for waveforms.

DCM-M1

LCD BOARD (SIDE B)
C4301
C4302
C4303
C4304
C4305
C4306
C4307
C4308
C4309
C4310
C4311
C4312
C4313
C4314
C4315
C4316
C4317
C4318
C4319
C4320
C4321
C4322
C4323
C4324
C4325
C4326
C4327
C4328
C4329
C4330
C4331
C4332
C4334
C4335
C4336
C4337
C4338
C4339
C4340
C4341
C4342
C4344
C4345
C4346
C4352

D-9
D-10
D-10
G-10
F-7
E-8
G-9
F-5
G-8
H-8
H-8
F-9
G-8
H-7
F-8
G-8
G-5
H-6
D-10
B-3
B-4
G-7
H-7
G-7
G-5
G-6
A-4
C-2
D-3
D-3
D-2
B-4
B-4
B-4
C-3
B-4
B-2
C-4
D-4
C-5
D-3
A-3
D-8
A-4
D-9

CN4301
CN4302
CN4303
CN4305
CN4306
CN4307

A-5
C-11
F-11
F-1
A-3
A-8

D4302
D4303
D4304

D-2
B-4
D-4

FB4301

A-4

IC4301
IC4302
IC4303
IC4304

E-9
F-7
C-3
C-4

L4301
L4302
L4303
L4305
L4306
L4307
L4308
L4309

E-10
E-10
E-8
G-6
B-4
C-2
B-3
B-2

Q4301
Q4302
Q4303
Q4304
Q4305
Q4306
Q4307
Q4308
Q4312
Q4313

E-4
E-3
G-9
G-8
H-8
H-9
G-8
H-7
D-3
D-4

R4301
R4302
R4303
R4304
R4305
R4309
R4310
R4313
R4314
R4315
R4316
R4317
R4318
R4319
R4320
R4321
R4322
R4323
R4324
R4325
R4326
R4327
R4328
R4329
R4330
R4331
R4334
R4335
R4336

F-9
G-8
G-9
G-9
G-9
E-4
F-6
G-9
H-8
H-8
H-8
F-7
F-6
F-8
F-8
H-8
G-8
F-6
F-6
F-6
F-6
F-6
G-9
F-6
F-6
F-9
F-9
H-7
G-7

R4337
R4338
R4339
R4340
R4343
R4344
R4345
R4347
R4350
R4351
R4353
R4354
R4356
R4357
R4358
R4359
R4360
R4362
R4366
R4369
R4370
R4371
R4372
R4373
R4374
R4375
R4376
R4377
R4378
R4379
R4380
R4381
R4382
R4383
R4384
R4385
R4386
R4387
R4388
R4389
R4390
R4391
R4392
R4393
R4394
R4395
R4396
R4397
R4400
R4401
R4402
R4403
R4405
R4407
R4408
R4409

G-8
E-3
H-7
G-8
G-8
H-7
F-8
F-8
G-6
G-7
F-8
D-3
D-2
D-3
C-3
B-5
B-5
D-3
C-2
B-4
C-4
C-4
C-4
C-4
C-4
C-4
C-4
C-4
C-4
C-5
C-5
C-5
D-3
C-4
E-4
E-3
C-5
G-2
F-2
F-2
F-2
A-5
F-2
D-10
E-10
D-11
D-11
E-7
B-2
C-4
B-5
F-6
F-9
H-7
D-8
E-8

ETHER board
(ETHER INTERFACE)

JACK board
(AV IN/OUT)
LCD board
(LCD)

4-105

Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.

Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce por tant le numéro
spécifié.

LCD
4-106

4-107

4-108

LCD

DCM-M1

ETHER (ETHER INTERFACE) PRINTED WIRING BOARD
– Ref. No.: ETHER board; 20,000 series –

• For Printed Wiring Board.
• There are few cases that the part isn't mounted in this model
is printed on this diagram.
• Chip transistor
C

B

E

ETHER board
(ETHER INTERFACE)

JACK board
(AV IN/OUT)
LCD board
(LCD)

ETHER INTERFACE
ETHER

4-109

4-110

4-111

4-112

DCM-M1

ETHER INTERFACE
4-113

4-114

4-115

ETHER

DCM-M1
ETHER (ETHER INTERFACE) SCHEMATIC DIAGRAM

• See page 4-109 for printed wiring board.

• See page 4-135 for waveforms.

ETHER INTERFACE
ETHER

4-116

4-117

4-118

DCM-M1

JACK (AV IN/OUT) SCHEMATIC DIAGRAM

• See page 4-121 for printed wiring board.

AV IN/OUT
4-119

4-120

JACK

DCM-M1

JACK (AV IN/OUT) PRINTED WIRING BOARD
– Ref. No.: JACK board; 20,000 series –

AV IN/OUT
JACK

4-121

4-122

DCM-M1

• For Printed Wiring Board.
• There are few cases that the part isn't mounted in this model
is printed on this diagram.

ETHER board
(ETHER INTERFACE)

JACK board
(AV IN/OUT)
LCD board
(LCD)

AV IN/OUT
4-123

4-124

JACK

DCM-M1

POWER (DC/DC CONVERTER) PRINTED WIRING BOARD
– Ref. No.: POWER board; 20,000 series –
POWER BOARD
(SIDE A)
C9001
C9002
C9003
C9004
C9009
C9011
C9015
C9052
C9055
C9057
C9061
C9063
C9064
C9065
C9068
C9076
C9080

A-10
A-10
A-10
C-9
C-8
C-8
C-6
A-9
C-5
C-5
C-5
C-5
C-1
C-4
C-1
C-4
C-5

CN9001

G-1

D9001
D9002
D9003
D9011
D9012

A-10
C-9
C-9
A-10
B-1

F9001
F9002

C-10
B-10

FB9001
FB9002

A-10
A-9

L9001
L9002
L9003
L9004
L9005
L9006
L9007
L9008
L9009
L9010
L9013
L9015
L9017
L9018
L9019
L9023

C-9
B-9
C-7
B-8
B-7
C-6
B-6
B-3
B-5
B-2
A-5
B-1
C-5
C-4
C-5
C-4

R9060
R9062
R9064
R9066
R9067
R9068

C-2
B-5
C-3
B-3
A-4
C-2

T9001

B-1

DC/DC CONVERTER
POWER

4-125

4-126

DCM-M1

• For Printed Wiring Board.
• There are few cases that the part isn't mounted in this model
is printed on this diagram.
• Chip transistor
C

B

4 5 6

E

3 2 1

BL board
(EVF BACK LIGHT)

VF board
(EVF)

POWER board
(DC/DC CONVERTER)

MAIN board
AUDIO/VIDEO DATA CONTROL, MPEG ENCODER/DECODER,
RF AMP/DRIVE, DIGITAL SIGNAL PROCESSOR,
SYSTEM CONTROL, VIDEO, AUDIO, SWITCHING REGULATOR

DC/DC CONVERTER
4-127

4-128

4-129

POWER

DCM-M1
POWER (DC/DC CONVERTER) SCHEMATIC DIAGRAM

DC/DC CONVERTER
POWER

4-130

• See page 4-125 for printed wiring board.

Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.

• See page 4-135 for waveforms.

Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce por tant le numéro
spécifié.

4-131

4-132

DCM-M1

4-3. WAVEFORMS
1

ql

0
2.88 Vp-p

7 Vp-p

360 mVp-p
H

V

H
REC/PB

REC/PB

REC/PB

2

w;

qa
2.96 Vp-p

7 Vp-p
H

1.12 Vp-p
H

2V
REC/PB

REC/PB

REC/PB

3

wa

qs
Approx.
3.4 Vp-p

1 Vp-p

3.1 Vp-p

13.5 MHz

H

V
REC/PB

REC/PB

REC/PB

4

qd

ws

3.28 Vp-p

3.6 Vp-p

1.22 Vp-p
20 MHz

18 MHz
REC/PB

H

REC/PB

REC/PB

qf

5

wd

3.12 Vp-p

408 mVp-p

16.33 MHz

1.12 Vp-p
6.6 MHz

32.768 kHz
REC/PB

REC/PB
6

REC/PB

qg

wf

2.24 Vp-p

2.32 Vp-p

1.1 Vp-p

36 MHz

9.8304 MHz

REC/PB

H

REC/PB

7

REC/PB
wg

qh
3.84 Vp-p

2.04 Vp-p

1.5 Vp-p

18 MHz

32.768 kHz

REC/PB

H
REC/PB

REC/PB
qj

8

wh

3.04 Vp-p

1.48 Vp-p

3.52 Vp-p
H
27 MHz

H

REC/PB

REC/PB

REC/PB
wj

qk

9

700 mVp-p

2.88 Vp-p

1.1 Vp-p
H

H

V
REC/PB

REC/PB

4-133

REC/PB

DCM-M1

ej

wk

rh

680 mVp-p

980 mVp-p
Approx.23.6 ms: MD1
Approx.14.8 ms: MD2
REC/PB

22.5792 MHz
REC/PB

H
REC/PB
ek

wl

rj

368 mVp-p

3.4 Vp-p

H

Approx.23.6 ms: MD1
Approx.14.8 ms: MD2
REC/PB

22.5792 MHz
REC/PB

REC/PB
el

e;

500 mVp-p

320 mVp-p
70.54 MHz
REC/PB

H
REC/PB

r;

ea

rl

Approx.
324 mVp-p

208 mVp-p

1.58 Vp-p
H

16.934 MHz
REC/PB

200 ns
PB (MD1)
es

REC/PB

ra

t;
3.84 Vp-p

Approx.
360 mVp-p

204 mVp-p

11.2896 MHz
100 ns
PB (MD2)

2H

REC/PB

ed

REC/PB

rs

ta

Approx.
200 mVp-p
44.1 kHz

PB (MD1)

2H

REC/PB

REC/PB

rd

ef

ts

Approx.
280 mVp-p
2..8224 MHz

PB (MD2)

200 ns: MD1
100 ns: MD2
PB
eh

200 ns: MD1
100 ns: MD2
PB

8 Vp-p

4.32 Vp-p

100 ns

eg

8 Vp-p

4.24 Vp-p

200 ns

2H
REC/PB

REC/PB
Approx.
1.54 Vp-p
: MD1
Approx.
1.86 Vp-p
: MD2

rf

rg
Approx.
1.22 Vp-p
: MD1
Approx.
880 mVp-p
: MD2

Approx.
560 mVp-p
: MD1
Approx.
780 mVp-p
: MD2

rk

Approx.
712 mVp-p
200 ns
PB (MD1)

Approx.
1.38 Vp-p
: MD1
Approx.
1.68 Vp-p
: MD2

td
3 Vp-p

8 Vp-p

Approx.12 ms: MD1
Approx.7.5 ms: MD2
REC/PB

Approx.23.6 ms: MD1
Approx.14.8 ms: MD2
REC/PB

4-134

2H
REC/PB
tf
Approx.
1 Vp-p
: MD1
Approx.
1.32 Vp-p
: MD2

12 Vp-p
H
REC/PB

DCM-M1

yf

tg

1.28 Vp-p

2.16 Vp-p
11 MHz

20 MHz
REC/PB

REC/PB
th

yg
560 mVp-p

800 mVp-p
470 kHz

H

REC/PB

REC/PB
yh

tj
220mVp-p

5.52 Vp-p
470 kHz

H

REC/PB

REC/PB
tk

yj
236 mVp-p

940 mVp-p

H

470 kHz
REC/PB

REC/PB
tl

yk
4 Vp-p

840 mVp-p

2H

470 kHz
REC/PB

REC/PB
y;

yl
4 Vp-p

1.44 Vp-p

2H

470 kHz
REC/PB

REC/PB
u;

ya
4 Vp-p

2.88 Vp-p

2H

470 kHz
REC/PB

REC/PB
ua

ys
1.26 Vp-p

5.44 Vp-p
470 kHz
REC/PB

2H
REC/PB
us

yd

3.12 Vp-p
15.4 MHz
REC/PB

840mVp-p
470 kHz
REC/PB

4-135E
4-135

DCM-M1
SECTION 5
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color

5-1.

• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.

The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.

MAIN SECTION

2
13

14

15

12

16

cabinet (R) section

11
9

2

10
#1

15

17

7
2
6
8
5

2

4
1
3

20

19
2
1
18
Ref. No.

Part No.

Description

Part No.

Description

1
2
3
4
5

4-223-679-23
4-223-676-15
3-977-650-01
4-218-461-11
4-216-024-01

SCREW (2.0), MI (M2.0X4.5)
SCREW (1.7), MI (M1.7X3)
SCREW, TRIPOD
SCREW (M1.7)
COVER, JACK

Remark

Ref. No.
11
12
13
14
15

4-216-049-01
4-219-035-01
X-4951-294-1
1-418-201-21
4-223-676-23

SHAFT (BRACKET REAR)
SCREW
CAP ASSY, LENS
SWITCH UNIT, MAIN CONTROL
SCREW (1.7), MI (M1.7X4)

6
7
8
9
10

4-216-022-01
4-216-023-01
4-218-462-01
4-221-110-01
4-216-036-01

BRACKET, BELT
SHAFT (BELT FRONT)
BELT, GRIP
BRACKET
BRACKET (REAR), BELT

16
17
18
19
20

4-223-676-31
4-220-888-01
X-4950-890-1
1-418-732-21
3-742-854-01

SCREW (1.7), MI (M1.7X4.5)
BRACKET (SHOE)
PEN ASSY, TOUCH
REMOTE COMMANDER (RMT-DCM1)
LID, BATTERY (for RMT-DCM1)

5-1

Remark

5-2.

CABINET (R) SECTION
69

68

70
67

71
72

73
79

80

75
51

74
77

66
not supplied

#2

51
65

81

64

not supplied

76
not supplied

74

59

63

83
78

59

74
77

59

82
#2

62

77
61
51

53

60

51
58

51
57
55
56

54
51

52
Ref. No.

Part No.

Description

51
52
* 53
54
* 55

4-218-461-01
A-3321-881-A
4-216-028-01
3-043-103-01
4-216-027-01

SCREW (M1.7)
POWER BOARD, COMPLETE
CASE (REAR), SHIELD
CUSHION (SHIELD)
CASE (FRONT), SHIELD

56
57
58
59
60

1-672-513-11
A-3321-883-A
4-216-025-01
4-224-946-01
4-224-945-01

61
* 62
63
64
65

1-418-563-11
4-220-720-01
4-216-021-01
4-223-676-15
4-225-467-01

66
67

Remark

Ref. No.

Part No.

Description

68
69
70
71
72

3-043-016-01
1-418-202-21
X-3378-880-1
4-216-052-01
4-984-017-21

RUBBER, GRIP
SWITCH UNIT, ZOOM
CABINET (R) SUB ASSY
BLIND (EVF), ADJUSTMENT
SCREW (1.7), TAPPING

TRANSLATION FLEXIBLE (JACK) BOARD
JACK BOARD, COMPLETE
BRACKET (JACK)
SPACER (JACK)
SPACER (REMOTE TERMINAL)

73
74
75
76
77

4-215-993-01
3-713-791-01
X-4950-899-1
3-972-819-01
4-223-676-23

SHEET, BT
SCREW (M1.7X5), TAPPING, P2
CASE ASSY, BATTERY
SPRING, BATTERY
SCREW (1.7), MI (M1.7X4)

TERMINAL UNIT, REMOTE
MATERIAL, ACOUSTIC ISOLATION (M)
BRACKET (FRONT), BELT
SCREW (1.7), MI (M1.7X3)
SEAL (JACK. ENGLISH)

78
79
80
81
82

1-694-497-11
4-219-034-01
4-215-995-01
A-3323-174-A
3-043-261-01

TERMINAL BOARD, BATTERY
SHEET, INSULATING
BRACKET (ETHER PC BOARD)
ETHER BOARD, COMPLETE
SHEET, COPY

83

3-044-616-01 SHEET, SHIELD

3-043-483-01 SHEET (GRIP RUBBER), ADHESIVE
3-043-015-01 RUBBER, GRIP

5-2

Remark

5-3.

MICROPHONE BLOCK SECTION

119

122

not supplied

116
116

118
121

116

115

#2

112
110

111

120
117
111
113

114
106
107

109
105

123

108
104
102
cabinet (L) section
#3

124
103

101
LCD block section

102

Ref. No.

Part No.

Description

Remark

101
102
* 103
104
* 105

4-216-044-01
4-223-676-15
4-220-721-01
4-216-045-01
4-220-719-01

COVER (FRONT), HINGE
SCREW (1.7), MI (M1.7X3)
MATERIAL, ACOUSTIC ISOLATION (S)
COVER (REAR), HINGE
MATERIAL, ACOUSTIC ISOLATION (L)

106
107
108
109
110

X-4950-891-1
4-223-676-09
X-4950-897-1
4-216-018-01
1-418-564-11

PLATE ASSY, BLIND
SCREW (1.7), MI (M1.7X2.5)
BASE ASSY, MICROPHONE
RUBBER, MICROPHONE
RAY-CATCHER BLOCK UNIT, REMOCON

111
112

4-984-017-21 SCREW (1.7), TAPPING
1-418-192-11 MICROPHONE UNIT

Ref. No.

5-3

Part No.

Description

113
114
115
116
117

4-220-639-01
4-216-019-01
3-043-171-01
4-218-461-01
4-220-640-01

ABSORBENT (GEL), ACOUSTIC
COVER, BASE
SHEET (MICROPHONE)
SCREW (M1.7)
ABSORBENT (SHEET), ACOUSTIC

118
119
120
121
122

3-713-791-01
3-335-797-01
A-3323-422-A
3-044-612-01
1-672-514-11

SCREW (M1.7X5), TAPPING, P2
SCREW (M1.4X2), TOOTHED LOCK
MAIN BOARD, COMPLETE
SHEET, SHIELD (IC3009)
TRANSLATION FLEXIBLE BOARD

123
124

4-215-975-21 CUSHION (PANEL)
3-043-102-01 FOOT (L), RUBBER

Remark

5-4.

CABINET (L) SECTION

169

167
168

171

170

EVF block section

172

155
166

160

164

168

164

173

CT-DCMM1-164

163

165

154
161
MT-DCMM1-163

162

160
152

159
158

157

156

154
152
155

153
151

152

Ref. No.

Part No.

Description

Part No.

Description

151
152
153
154
155

X-3378-420-1
4-218-229-19
3-320-382-11
4-218-458-01
4-223-676-15

PANEL ASSY, UPPER
SCREW (1.4), MI (M1.4X2)
FOOT, RUBBER
DAMPER (MD)
SCREW (1.7), MI (M1.7X3)

Remark

Ref. No.
163
164
165
166
167

3-837-971-01
4-215-989-01
4-218-461-01
4-220-349-01
4-216-053-01

CUSHION
CUSHION (MD)
SCREW (M1.7)
CUSHION (CAMERA)
CUSHION (CABINET)

156
157
158
159
160

X-3378-881-1
X-4950-893-1
4-995-402-01
3-914-116-01
4-215-976-01

CABINET (FRONT) ASSY
CHASSIS (F) ASSY
SPRING (LOCK), TENSION
SPRING (R), TENSION
SCREW (DAMPER)

168
169
170
171
172

4-223-676-09
X-3378-951-1
X-4950-892-1
4-223-676-23
4-221-112-01

SCREW (1.7), MI (M1.7X2.5)
CONTROL SW SUB ASSY, UPPER
BUTTON ASSY, AUDIO CONTROL
SCREW (1.7), MI (M1.7X4)
SHAFT

161
162

4-215-989-21 CUSHION (MD)
X-4950-894-1 CHASSIS (M) ASSY

173

3-842-935-01 CUSHION

5-4

Remark

5-5.

LCD BLOCK SECTION

216
215

217
205

205
209

208

218
220
219

210
214
211

207
224

206
223
205

213
221

203

204

222
LCD4301

202

212

201

The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.

Ref. No.

Part No.

Description

201
202
203
* 204
205

X-3378-952-1
4-216-051-01
4-223-676-15
4-216-034-01
4-223-676-09

CABINET ASSY (U), LCD
BLIND (LCD), ADJUSTMENT
SCREW (1.7), MI (M1.7X3)
FRAME, LCD
SCREW (1.7), MI (M1.7X2.5)

206
207
208
209
210

4-218-461-01
1-959-252-11
1-959-251-11
4-220-687-01
A-3323-169-A

SCREW (M1.7)
HARNESS (GLAY)
HARNESS (YELLOW)
TAPE (LCD), HARNESS BLIND
LCD BOARD, COMPLETE

211
212
0 213

Remark

Ref. No.

4-220-440-01 SHEET (LCD), SHIELD
4-926-578-01 PLATE (P), RUBBER
1-517-843-11 FLUORESCENT TUBE

Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.

Part No.

Description

Remark

214
215
216
217
218

X-4950-896-1
1-672-355-11
4-223-676-07
4-216-041-01
3-051-046-01

HINGE ASSY
LCD DETECTION SW FLEXIBLE BOARD
SCREW (1.7), MI (M1.7X2)
CABINET (O), LCD
SLEEVE, HARNESS

219
220
221
222
223

4-216-047-01
4-216-043-01
1-803-445-11
4-218-463-01
3-042-678-01

SPRING (LOCK), TORSION
LOCK, LCD
PANEL, TOUCH
SPACER (LCD)
SHEET (LCD), ELECTROSTATIC

224
3-042-688-01 SHEET (LCD FLEXIBLE RETAINER)
LCD4301 1-803-033-21 INDICATOR MODULE, LIQUID CRYSTAL

5-5

5-6.

EVF BLOCK SECTION

259
258
257

260
256
255
261
253
254
253
262

252
LCD4701

263
264
263
265

251
267

266

Ref. No.

Part No.

Description

Remark

Ref. No.

251
252
253
254
255

1-672-356-11
A-3321-877-A
3-989-416-01
3-988-563-01
3-960-302-11

VF/LCD FLEXIBLE BOARD
BL BORAD, COMPLETE
CUSHION (458), LCD
ILLUMINATOR (458), BL
CUSHION (1), LCD

260
261
262
263
264

256
257
258
259

X-3948-473-1
4-216-042-01
3-988-565-01
3-988-564-01

LENS ASSY (458), VF
CABINET (UPPER), EVF
SHEET, VF COVER ADHESIVE
COVER, VF

265
4-218-459-01
266
A-3321-879-A
267
1-672-357-11
LCD4701 8-753-023-89

5-6

Part No.

Description

4-216-039-01
4-218-460-01
4-216-040-01
3-713-791-01
3-950-044-01

CUP, EYE
ARM, VISIBILITY ADJUSTMENT
CABINET (LOWER), EVF
SCREW (M1.7X5), TAPPING, P2
RING, O
KNOB, VISIBILITY ADJUSTMENT
VF BORAD, COMPLETE
VF FLEXIBLE BOARD
LCX024AK-5

Remark

5-7.

LENS BLOCK SECTION
(CT-DCMM1-164)

309

310
310

308

307

302
306
305

302

not
supplied
not supplied
(IC001)

311

304
303

301

302

Ref. No.

Part No.

Description

301
302
* 303
304
305

A-3250-920-A
3-713-791-01
4-215-973-01
8-848-732-01
3-963-467-11

CT-DCMM1-164
SCREW (M1.7X4), TAPPING, P2
BRACKET, LENS FRAME
DEVICE, LENS (LSV-620B)
ADAPTOR (FH), CCD FITTING

306

Remark

Ref. No.

Part No.

Description

307
* 308
309
310
311

3-961-192-01
4-215-974-01
4-215-989-21
3-335-797-01
3-318-203-11

RUBBER (FH), SEAL
BRACKET, LENS BLOCK
CUSHION (MD)
SCREW (M1.4X2), TOOTHED LOCK
SCREW (B1.7X6), TAPPING

1-758-202-21 FILTER BLOCK, OPTICAL

5-7

Remark

5-8.

MECHANISM DECK SECTION-1
(MT-DCMM1-163)

366
370

M5811

369

356

365
364
363

355
362

368

354

361
360
367

359

358
357

353

Ref. No.

Part No.

Description

351
352
353
354
355

3-349-825-41
A-3321-863-A
X-4951-230-1
4-217-955-01
4-963-883-41

SCREW
REC BOARD, COMPLETE
HOLDER ASSY
SPRING (POWER TENSION), TENSION
SCREW (M1.4), PRECISION PAN

Remark

356
357
358
359
360

4-217-946-01
3-315-414-41
4-217-950-01
4-217-957-01
4-996-249-01

GUIDE, HOLDER
WASHER
GEAR, WORM
SPRING (WORM GEAR), COIL
SCREW (M1.2X1.2)

361

4-217-944-01 GEAR (STEPPER)

Ref. No.

352

Part No.

Description

362
363
364
365
366

4-217-948-01
X-4951-231-1
3-338-645-31
4-963-883-01
4-217-958-01

GEAR (WORM WHEEL)
HOLDER (STEPPER) ASSY
WASHER (0.8-2.5)
SCREW (M1.4), PRECISION PAN
SHEET, ADHESIVE

367
* 368
* 369
370
M5811

A-3323-163-A
4-217-952-01
4-217-953-01
4-963-883-21
1-698-543-21

CLV BOARD, COMPLETE
SHIELD (A)
SHIELD (B)
SCREW (M1.4), PRECISION PAN
MOTOR (STEPPING)

5-8

351

Remark

5-9.

MECHANISM DECK SECTION-2
(MT-DCMM1-163)

not supplied
(HR5901)

422
420

418

423

not
supplied

421

417
416
419
411
410

409

415
414

413
412

405
not supplied
(M5801)

404

408

not supplied
(M5821)

406
407
405

402

401

Ref. No.

Part No.

Description

401
402
403
404
405

X-4952-432-1
4-963-883-21
X-4951-229-1
4-995-585-01
4-963-897-01

* 406
407
408
409
410

4-217-956-01
3-704-197-33
1-675-950-11
1-418-191-11
4-217-928-01

411
* 412

4-217-954-01 SCREW (M1.4X4), TAPPING
4-217-943-01 BRACKET, MOTOR

403

Remark

Ref. No.

Part No.

Description

SERVICE ASSY, OP
SCREW (M1.4), PRECISION PAN
CHASSIS ASSY
SPRING (LIMITTER), TORSION
HOLDER (GUIDE SHAFT)

413
414
* 415
416
417

3-704-246-01
4-217-941-01
4-217-949-01
4-217-927-01
1-452-997-11

SCREW (P 1.4X1.6)
BRACKET (LEAD SCREW)
SHAFT (MAIN GUIDE)
GEAR (B)
ENCODER, MAGNET

SHAFT (SUB GUIDE)
SCREW (M1.4X3.0), LOCKING
MOTOR FLEXIBLE BOARD
SENSOR, MR
GEAR (A)

* 418
419
420
421
422

4-217-942-01
4-963-883-81
4-963-883-41
4-217-947-01
4-955-841-11

SCREW, LEAD
SCREW (M1.4), PRECISION PAN
SCREW (M1.4), PRECISION PAN
SPRING, THRUST
SCREW

423

5-9
5-9E

4-217-951-01 COVER, MD

Remark

DCM-M1
SECTION 6
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable

Ref. No.

Part No.

• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH

Description

Remark

Ref. No.

A-3321-877-A BL BOARD, COMPLETE
*******************
(Ref. No.: 20,000 Series)

1-162-970-11
1-113-642-11
1-115-566-11
1-164-677-11
1-115-464-91

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.01uF
47uF
4.7uF
0.033uF
0.0022uF

10%
20%
10%
10%
10%

25V
10V
10V
16V
630V

< CONNECTOR >
CN4701 1-784-421-11 CONNECTOR, FFC/FPC (ZIF) 27P
CN4702 1-691-354-21 CONNECTOR, FFC/FPC (ZIF) 16P
< DIODE >
0 D4701

1-410-389-31 INDUCTOR CHIP 47uH
1-414-398-11 INDUCTOR
10uH
< FLUORESCENT INDICATOR >

0 ND4701 1-517-758-11 TUBE, FLUORESCENT (0.55 INCH)

0 Q4701

8-729-039-24 TRANSISTOR

FX216-TL1

< RESISTOR >
R4701
R4702

1-218-883-11 METAL CHIP
1-216-809-11 METAL CHIP

33K
100

0.5%
5%

Les composants identifiés par une
marque 0 sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
When indicating parts by reference
number, please include the board.

Description

Remark

C5804
C5805
C5806
C5807
C5808

1-164-943-11
1-164-943-11
1-107-820-11
1-164-874-11
1-164-874-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.01uF
0.01uF
0.1uF
100PF
100PF

10%
10%
0%
5%
5%

16V
16V
16V
16V
16V

C5809
C5810
C5811
C5812
C5813

1-164-943-11
1-164-943-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.01uF
0.01uF
0.1uF
0.1uF
0.1uF

10%
10%
0%
0%
0%

16V
16V
16V
16V
16V

C5814
C5815
C5816
C5817
C5818

1-107-820-11
1-107-820-11
1-125-777-11
1-113-991-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
33uF
0.1uF

0%
0%
10%
20%
0%

16V
16V
10V
16V
16V

C5819
C5820
C5823
C5824
C5825

1-107-820-11
1-113-682-11
1-164-939-11
1-164-939-11
1-164-939-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
33uF
0.0022uF
0.0022uF
0.0022uF

0%
20%
10%
10%
10%

16V
10V
16V
16V
16V

C5826
C5827
C5828
C5829
C5851

1-164-939-11
1-164-939-11
1-164-939-11
1-113-991-11
1-115-566-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

0.0022uF
0.0022uF
0.0022uF
33uF
4.7uF

10%
10%
10%
20%
10%

16V
16V
16V
16V
10V

C5852
C5853
C5854

1-125-777-11 CERAMIC CHIP 0.1uF
1-164-870-11 CERAMIC CHIP 68PF
1-135-070-00 TANTALUM CHIP 0.1uF

10%
5%
10%

10V
16V
35V

< CONNECTOR >

1/16W
1/16W

* CN5801 1-778-158-21 CONNECTOR, FFC/FPC (ZIF) 10P
CN5803 1-778-592-21 CONNECTOR, BOARD TO BOARD 50P

< TRANSFORMER >
0 T4701 1-426-848-51 TRANSFORMER, INVERTER
************************************************************

< DIODE >
D5801

8-719-048-98 DIODE RB160L-40TE25

A-3323-163-A CLV BOARD, COMPLETE
*********************
(Ref. No.: 20,000 Series)
*
*

The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.

8-719-056-49 DIODE 1SS370 (TE85L)
< COIL >

L4701
L4702

Part No.

CLV

< CAPACITOR >

< CAPACITOR >
C4701
C4702
C4703
C4704
0 C4706

BL

< IC >
IC5801
IC5802
IC5803
IC5804
IC5805

4-217-952-01 SHIELD (A)
4-217-953-01 SHIELD (B)

6-1

8-759-358-40
8-759-572-35
8-759-358-40
8-759-082-55
8-759-082-57

IC
IC
IC
IC
IC

TLC372CPW-E20
TLC3702CPWR
TLC372CPW-E20
TC7W00FU
TC7W04FU

CLV
Ref. No.
IC5806
IC5807
IC5808
IC5851

ETHER
Part No.
8-759-082-55
8-759-572-28
8-759-082-55
8-759-572-54

Description
IC
IC
IC
IC

Remark

Ref. No.

TC7W00FU
NJU7016R
TC7W00FU
TA6009FN (EL)

Part No.

Description

R5832
R5833
R5834
R5851

1-218-965-11
1-218-965-11
1-218-965-11
1-218-967-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

R5852

1-218-987-11 RES, CHIP

Remark
10K
10K
10K
15K

5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W

680K

5%

1/16W

< COIL >
< SWITCH >
L5801

1-416-928-21 INDUCTOR

470uH
S5801
S5802
S5803
S5804
S5805

< TRANSISTOR >
Q5801
Q5802
Q5803
Q5808
Q5809

8-729-047-36
8-729-046-70
8-729-037-89
8-729-037-73
8-729-037-73

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

CPH3303-TL
XP4654- (TX).SO
2SC4627J-C (TX).SO
UN9212J- (TX).SO
UN9212J- (TX).SO

Q5810
Q5811
Q5812
Q5813
Q5821

8-729-037-73
8-729-037-73
8-729-037-73
8-729-037-73
8-729-044-26

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

UN9212J- (TX).SO
UN9212J- (TX).SO
UN9212J- (TX).SO
UN9212J- (TX).SO
CPH3404-TL

Q5822
Q5823
Q5824
Q5825
Q5826

8-729-044-26
8-729-044-26
8-729-044-26
8-729-044-26
8-729-044-26

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

CPH3404-TL
CPH3404-TL
CPH3404-TL
CPH3404-TL
CPH3404-TL

1-692-847-21
1-692-377-31
1-692-377-31
1-572-467-61
1-572-467-61

SWITCH, PUSH (1 KEY) (PROTECT)
SWITCH, PUSH (1 KEY) (REFLECT)
SWITCH, PUSH (1 KEY) (MD1/2)
SWITCH, PUSH (1 KEY) (INITIAL)
SWITCH, PUSH (1 KEY) (IN LIMIT)
< SENSOR >

SE5851 1-418-203-21 SENSOR, SHOCK (SHOCK SENSOR)
************************************************************
A-3323-174-A ETHER BOARD, COMPLETE
***********************
(Ref. No.: 20,000 Series)
3-043-261-01 SHEET, COPY
3-044-616-01 SHEET, SHIELD
< CAPACITOR >

< RESISTOR >
R5801
R5802
R5803
R5804
R5805

1-218-965-11
1-218-977-11
1-218-977-11
1-218-965-11
1-218-965-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

10K
100K
100K
10K
10K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5806
R5807
R5808
R5809
R5810

1-218-971-11
1-218-953-11
1-218-965-11
1-218-971-11
1-218-953-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

33K
1K
10K
33K
1K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5811
R5812
R5813
R5814
R5815

1-218-969-11
1-218-965-11
1-218-977-11
1-218-977-11
1-218-977-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

22K
10K
100K
100K
100K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5816
R5817
R5818
R5819
R5820

1-218-977-11
1-218-977-11
1-218-977-11
1-218-965-11
1-218-973-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

100K
100K
100K
10K
47K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5821
R5822
R5823
R5824
R5825

1-218-955-11
1-218-961-11
1-218-965-11
1-218-965-11
1-218-990-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
SHORT

1.5K
4.7K
10K
10K
0

5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W

R5826
R5827
R5828
R5829
R5830

1-218-975-11
1-218-975-11
1-218-975-11
1-218-975-11
1-218-975-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

68K
68K
68K
68K
68K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5831

1-218-975-11 RES, CHIP

68K

5%

1/16W

C8801
C8802
C8803
C8804
C8805

1-107-820-11
1-104-851-11
1-107-820-11
1-164-943-11
1-107-820-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
10uF
0.1uF
0.01uF
0.1uF

0%
20%
0%
10%
0%

16V
10V
16V
16V
16V

C8806
C8807
C8808
C8809
C8810

1-107-820-11
1-164-858-11
1-164-854-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
22PF
15PF
0.1uF
0.1uF

0%
5%
5%
0%
0%

16V
16V
16V
16V
16V

C8811
C8812
C8813
C8814
C8815

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

0%
0%
0%
0%
0%

16V
16V
16V
16V
16V

C8816
C8817
C8818
C8819
C8820

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-164-937-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.001uF

0%
0%
0%
0%
10%

16V
16V
16V
16V
16V

< CONNECTOR >
CN8801 1-778-598-21 CONNECTOR, BOARD TO BOARD 60P
CN8802 1-537-439-41 TARMINAL BOARD, CONNECTOR 20P
< IC/FILTER >

6-2

IC8801
IC8802
IC8803
IC8804
IC8805

8-759-573-34
8-759-573-34
8-759-573-34
8-759-573-34
8-759-573-34

IC
IC
IC
IC
IC

74LVX4245MTCX
74LVX4245MTCX
74LVX4245MTCX
74LVX4245MTCX
74LVX4245MTCX

IC8806
IC8807
IC8808

8-759-572-50 IC MB86967PFV-G-BND
1-803-453-11 FILTER MODULE, PCMCIA
8-759-573-35 IC KM62256DLTG-7L

ETHER
Ref. No.

Part No.

Description

Ref. No.

Remark

< COIL >
L8801

1-414-753-91 INDUCTOR

8-729-047-36 TRANSISTOR

Description

LCD
Remark

FB2101 1-469-637-21 FERRITE
FB2102 1-469-637-21 FERRITE

0uH
0uH

FB2103
FB3001
FB3002
FB3003
FB3101

0uH
0uH
0uH
0uH
0uH

4.7uH

< TRANSISTOR >
Q8801

Part No.

JACK

CPH3303-TL

1-469-637-21
1-469-637-21
1-469-637-21
1-469-637-21
1-469-637-21

FERRITE
FERRITE
FERRITE
FERRITE
FERRITE

< RESISTOR >
< JACK/CONNECTOR >
R8801
R8803

1-218-977-11 RES, CHIP
1-218-957-11 RES, CHIP

100K
2.2K

5%
5%

1/16W
1/16W

J3001
J3002
J3003
J4001

< VIBRATOR >

1-779-881-21
1-569-950-21
1-778-040-11
1-779-870-11

X8801 1-781-265-21 VIBRATOR, CRYSTAL (20MHz)
************************************************************

< RESISTOR >

A-3321-883-A JACK BOARD, COMPLETE
**********************
(Ref. No.: 20,000 Series)

R3051
R3052
R3053
R3055
R4051

< CAPACITOR >
C1001
C1014
C2001
C2014
C3008

1-164-937-11
1-164-937-11
1-164-937-11
1-164-937-11
1-164-937-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.001uF
0.001uF
0.001uF
0.001uF
0.001uF

10%
10%
10%
10%
10%

16V
16V
16V
16V
16V

C3060
C3061

1-164-937-11 CERAMIC CHIP
1-164-937-11 CERAMIC CHIP

0.001uF
0.001uF

10%
10%

16V
16V

JACK (MIC)
JACK (i)
JACK, SMALL TYPE (AUDIO/VIDEO)
CONNECTOR (ROUND TYPE) 4P (S. VIDEO)

1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-216-821-11

SHORT
SHORT
SHORT
SHORT
METAL CHIP

0
0
0
0
1K

5%

1/16W

< VARISTOR >
VDR103 1-801-923-11 VARISTOR, CHIP
VDR203 1-801-923-11 VARISTOR, CHIP
************************************************************
A-3323-169-A LCD BOARD, COMPLETE
*********************
(Ref. No.: 20,000 Series)

< CONNECTOR >
4-220-440-01 SHEET (LCD), SHIELD
CN3003 1-778-596-21 CONNECTOR, BOARD TO BOARD 30P
CN8004 1-778-711-11 CONNECTOR, FFC/FPC (ZIF) 5P

< CAPACITOR >

< DIODE >
D1001
D1002
D2001
D2002
D3001

8-719-074-62
8-719-074-62
8-719-074-62
8-719-074-62
8-719-074-62

DIODE
DIODE
DIODE
DIODE
DIODE

MAZS082001SO
MAZS082001SO
MAZS082001SO
MAZS082001SO
MAZS082001SO

D3002
D3003
D3004
D3005
D3006

8-719-074-62
8-719-074-62
8-719-074-62
8-719-074-62
8-719-074-62

DIODE
DIODE
DIODE
DIODE
DIODE

MAZS082001SO
MAZS082001SO
MAZS082001SO
MAZS082001SO
MAZS082001SO

D3007
D3008
D4001
D4002
D4003

8-719-074-62
8-719-074-62
8-719-074-62
8-719-074-62
8-719-074-62

DIODE
DIODE
DIODE
DIODE
DIODE

MAZS082001SO
MAZS082001SO
MAZS082001SO
MAZS082001SO
MAZS082001SO

D4004
D4005
D8011
D8012
D8013

8-719-074-62
8-719-074-62
8-719-074-62
8-719-074-62
8-719-074-62

DIODE
DIODE
DIODE
DIODE
DIODE

MAZS082001SO
MAZS082001SO
MAZS082001SO
MAZS082001SO
MAZS082001SO

< FERRITE BEAD >
FB1101 1-469-637-21 FERRITE
FB1102 1-469-637-21 FERRITE
FB1103 1-469-637-21 FERRITE

0uH
0uH
0uH

6-3

C4301
C4302
C4303
C4304
C4305

1-125-777-11
1-117-919-11
1-117-919-11
1-119-750-11
1-125-777-11

CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP

0.1uF
10uF
10uF
22uF
0.1uF

10%
20%
20%
20%
10%

10V
6.3V
6.3V
6.3V
10V

C4306
C4307
C4308
C4309
C4310

1-125-777-11
1-117-919-11
1-104-752-11
1-164-004-11
1-119-750-11

CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP

0.1uF
10uF
33uF
0.1uF
22uF

10%
20%
20%
10%
20%

10V
6.3V
6.3V
25V
6.3V

C4311
C4312
C4313
C4314
C4315

1-125-777-11
1-135-180-21
1-164-004-11
1-119-750-11
1-164-943-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

0.1uF
3.3uF
0.1uF
22uF
0.01uF

10%
20%
10%
20%
10%

10V
6.3V
25V
6.3V
16V

C4316
C4317
C4318
C4319
C4320

1-125-777-11
1-119-751-11
1-164-004-11
1-125-777-11
1-164-866-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
22uF
0.1uF
0.1uF
47PF

10%
20%
10%
10%
5%

10V
16V
25V
10V
16V

C4321
C4322
C4323
C4324
C4325

1-164-882-11
1-110-501-11
1-110-501-11
1-110-501-11
1-104-851-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP

220PF
0.33uF
0.33uF
0.33uF
10uF

5%
10%
10%
10%
20%

16V
16V
16V
16V
10V

C4326

1-125-777-11 CERAMIC CHIP

0.1uF

10%

10V

LCD
Ref. No.

Part No.

Description

C4327
C4328
C4329
C4330

1-117-919-11
1-164-004-11
1-125-777-11
1-110-501-11

TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

10uF
0.1uF
0.1uF
0.33uF

20%
10%
10%
10%

Remark
6.3V
25V
10V
16V

C4331
C4332
C4334
C4335
C4336

1-164-870-11
1-164-004-11
1-164-937-11
1-164-862-11
1-164-004-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

68PF
0.1uF
0.001uF
33PF
0.1uF

5%
10%
10%
5%
10%

16V
25V
16V
16V
25V

C4337
C4338
C4339
C4340
C4341

1-164-934-11
1-125-777-11
1-125-777-11
1-113-985-11
1-109-982-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

330PF
0.1uF
0.1uF
10uF
1uF

10%
10%
10%
20%
10%

16V
10V
10V
20V
10V

C4342
C4344
C4345
C4346
C4352

1-113-985-11
1-107-682-11
1-119-751-11
1-125-777-11
1-162-964-11

TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP

10uF
1uF
22uF
0.1uF
0.001uF

20%
10%
20%
10%
10%

20V
16V
16V
10V
50V

Ref. No.
Q4306
Q4307
Q4308
Q4312
Q4313

CONNECTOR, FFC/FPC (ZIF) 6P
PIN, CONNECTOR (PC BOARD) 14P
PIN, CONNECTOR (PC BOARD) 14P
CONNECTOR, FFC/FPC (LIF) 9P
CONNECTOR, FFC/FPC (ZIF) 24P

* CN4307 1-569-352-11 HOUSING, CONNECTOR 10P
< DIODE >
D4302
D4303
D4304

8-713-102-80 DIODE 1T369-01-T8A
8-713-102-80 DIODE 1T369-01-T8A
8-719-421-69 DIODE MA133
< FERRITE BEAD >

FB4301 1-414-445-11 FERRITE

0uH

< IC >
IC4301
IC4302
IC4303
IC4304

8-759-596-12
8-759-539-27
8-759-524-61
8-759-327-01

IC
IC
IC
IC

Description

8-729-037-53
8-729-037-53
8-729-037-53
8-729-037-52
8-729-037-53

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

Remark
2SB1462J-QR (TX).SO
2SB1462J-QR (TX).SO
2SB1462J-QR (TX).SO
2SD2216J-QR (TX).SO
2SB1462J-QR (TX).SO

< RESISTOR >

< CONNECTOR >
* CN4301 1-778-154-21
* CN4302 1-785-283-41
CN4303 1-785-283-21
CN4305 1-764-708-21
* CN4306 1-778-172-11

Part No.

AK9813AFS-E2
IR3Y37A4
CM7018L3-T4
NJM062V (TE2)

R4301
R4302
R4303
R4304
R4305

1-208-691-11
1-208-675-11
1-208-683-11
1-218-971-11
1-218-975-11

METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP

2.2K
470
1K
33K
68K

0.5%
0.5%
0.5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4309
R4310
R4313
R4314
R4315

1-218-929-11
1-218-973-11
1-218-957-11
1-218-849-11
1-208-675-11

RES, CHIP
RES, CHIP
RES, CHIP
METAL CHIP
METAL CHIP

10
47K
2.2K
3.3K
470

5%
5%
5%
0.5%
0.5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4316
R4317
R4318
R4319
R4320

1-208-683-11
1-218-971-11
1-218-967-11
1-218-967-11
1-218-967-11

METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
33K
15K
15K
15K

0.5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4321
R4322
R4323
R4324
R4325

1-218-971-11
1-218-975-11
1-218-969-11
1-218-967-11
1-218-973-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

33K
68K
22K
15K
47K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4326
R4327
R4328
R4329
R4330

1-218-967-11
1-218-971-11
1-218-957-11
1-218-963-11
1-218-975-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

15K
33K
2.2K
6.8K
68K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4331
R4334
R4335
R4336
R4337

1-218-983-11
1-218-990-11
1-208-691-11
1-208-675-11
1-208-683-11

RES, CHIP
SHORT
METAL CHIP
METAL CHIP
METAL CHIP

330K
0
2.2K
470
1K

5%

1/16W

0.5%
0.5%
0.5%

1/16W
1/16W
1/16W

R4338
R4339
R4340
R4343
R4344

1-218-929-11
1-218-971-11
1-218-975-11
1-218-977-11
1-218-957-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

10
33K
68K
100K
2.2K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4345
R4347
R4350
R4351
R4353

1-218-990-11
1-218-965-11
1-216-009-91
1-218-990-11
1-218-975-11

SHORT
RES, CHIP
RES, CHIP
SHORT
RES, CHIP

0
10K
22
0
68K

5%
5%

1/16W
1/10W

5%

1/16W

R4354
R4356
R4357
R4358
R4359

1-218-990-11
1-218-983-11
1-218-975-11
1-218-990-11
1-208-939-11

SHORT
RES, CHIP
RES, CHIP
SHORT
METAL CHIP

0
330K
68K
0
150K

5%
5%

1/16W
1/16W

0.5%

1/16W

R4360
R4362
R4366
R4369
R4370

1-208-955-11
1-218-990-11
1-208-931-11
1-218-965-11
1-218-989-11

METAL CHIP
SHORT
METAL CHIP
RES, CHIP
RES, CHIP

680K
0
68K
10K
1M

0.5%

1/16W

0.5%
5%
5%

1/16W
1/16W
1/16W

< COIL >
L4301
L4302
L4303
L4305
L4306

1-414-754-11
1-414-754-11
1-414-404-41
1-414-754-11
1-414-754-11

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

10uH
10uH
100uH
10uH
10uH

L4307
L4308
L4309

1-414-754-11 INDUCTOR
1-412-945-11 INDUCTOR
1-414-754-11 INDUCTOR

10uH
3.3uH
10uH

< TRANSISTOR >
Q4301
Q4302
Q4303
Q4304
Q4305

8-729-044-38
8-729-044-38
8-729-037-53
8-729-037-53
8-729-037-53

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

SI6552DQ-T1
SI6552DQ-T1
2SB1462J-QR (TX).SO
2SB1462J-QR (TX).SO
2SB1462J-QR (TX).SO

6-4

LCD
Ref. No.

Part No.

Description

R4371
R4372
R4373
R4374
R4375

1-218-975-11
1-218-969-11
1-218-973-11
1-218-961-11
1-218-933-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

68K
22K
47K
4.7K
22

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4376
R4377
R4378
R4379
R4380

1-218-975-11
1-218-961-11
1-218-977-11
1-218-971-11
1-218-977-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

68K
4.7K
100K
33K
100K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4381
R4382
R4383
R4384
R4385

1-218-971-11
1-218-967-11
1-218-965-11
1-218-929-11
1-218-929-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

33K
15K
10K
10
10

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4386
R4387
R4388
R4389
R4390

1-218-990-11
1-218-937-11
1-218-937-11
1-218-937-11
1-218-961-11

SHORT
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

0
47
47
47
4.7K

5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W

R4391
R4392
R4393
R4394
R4395

1-218-977-11
1-218-961-11
1-218-990-11
1-218-990-11
1-218-990-11

RES, CHIP
RES, CHIP
SHORT
SHORT
SHORT

100K
4.7K
0
0
0

5%
5%

1/16W
1/16W

R4396
R4397
R4400
R4401
R4402

1-218-990-11
1-218-971-11
1-218-990-11
1-218-933-11
1-208-719-11

SHORT
RES, CHIP
SHORT
RES, CHIP
METAL CHIP

0
33K
0
22
33K

Ref. No.

Remark

5%

1/16W

5%
0.5%

1/16W
1/16W

R4403 1-218-961-11 RES, CHIP
4.7K
5%
1/16W
R4405 1-208-711-11 METAL CHIP
15K
0.5% 1/16W
R4407 1-208-707-11 METAL CHIP
10K
0.5% 1/16W
R4408 1-217-671-11 METAL CHIP
1
5%
1/10W
R4409 1-217-671-11 METAL CHIP
1
5%
1/10W
************************************************************
A-3323-422-A MAIN BOARD, COMPLETE
*********************
(Ref. No.: 10,000 Series)
< CAPACITOR >
C1003
C1004
C1005
C1006
C1007

1-163-077-00
1-125-891-11
1-164-480-11
1-125-777-11
1-164-677-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.47uF
0.01uF
0.1uF
0.033uF

10%
10%
10%
10%
10%

25V
10V
50V
10V
16V

C1008
C1009
C1010
C1011
C1012

1-162-967-11
1-164-943-11
1-164-677-11
1-164-677-11
1-164-874-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.0033uF
0.01uF
0.033uF
0.033uF
100PF

10%
10%
10%
10%
5%

50V
16V
16V
16V
16V

C1013
C1014
C1015
C1016
C1017

1-135-337-11
1-125-837-91
1-135-177-21
1-125-837-91
1-117-919-11

TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP

1uF
1uF
1uF
1uF
10uF

20%
10%
20%
10%
20%

6.3V
6.3V
20V
6.3V
6.3V

C1018
C1019

1-117-919-11 TANTALUM CHIP 10uF
1-164-935-11 CERAMIC CHIP 470PF

20%
10%

6.3V
16V

6-5

Part No.

Description

MAIN
Remark

C1020
C1021
C1022

1-107-686-11 TANTALUM CHIP 4.7uF
20%
1-125-891-11 CERAMIC CHIP 0.47uF
10%
1-164-939-11 CERAMIC CHIP 0.0022uF 10%

16V
10V
16V

C2003
C2004
C2005
C2006
C2007

1-163-077-00
1-125-891-11
1-164-480-11
1-125-777-11
1-164-677-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.47uF
0.01uF
0.1uF
0.033uF

10%
10%
10%
10%
10%

25V
10V
50V
10V
16V

C2008
C2009
C2010
C2011
C2012

1-162-967-11
1-164-943-11
1-164-677-11
1-164-677-11
1-164-874-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.0033uF
0.01uF
0.033uF
0.033uF
100PF

10%
10%
10%
10%
5%

50V
16V
16V
16V
16V

C2013
C2014
C2015
C2016
C2017

1-135-337-11
1-125-837-91
1-135-177-21
1-125-837-91
1-117-919-11

TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP

1uF
1uF
1uF
1uF
10uF

20%
10%
20%
10%
20%

6.3V
6.3V
20V
6.3V
6.3V

C2018
C2019
C2020
C2021
C2022

1-117-919-11
1-164-935-11
1-107-686-11
1-125-891-11
1-164-939-11

TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP

10uF
470PF
4.7uF
0.47uF
0.0022uF

20%
10%
20%
10%
10%

6.3V
16V
16V
10V
16V

C3001
C3002
C3003
C3004
C3005

1-164-937-11
1-164-943-11
1-135-337-11
1-107-820-11
1-117-919-11

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP

0.001uF
0.01uF
1uF
0.1uF
10uF

10%
10%
20%
0%
20%

16V
16V
6.3V
16V
6.3V

C3006
C3007
C3008
C3011
C3013

1-107-820-11
1-107-820-11
1-125-891-11
1-117-919-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.47uF
10uF
0.1uF

0%
0%
10%
20%
0%

16V
16V
10V
6.3V
16V

C3014
C3015
C3016
C3017
C3018

1-107-686-11
1-107-820-11
1-107-686-11
1-107-820-11
1-135-337-11

TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP

4.7uF
0.1uF
4.7uF
0.1uF
1uF

20%
0%
20%
0%
20%

16V
16V
16V
16V
6.3V

C3019
C3021
C3022
C3023
C3025

1-107-820-11
1-119-750-11
1-107-820-11
1-110-569-11
1-107-820-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

0.1uF
22uF
0.1uF
47uF
0.1uF

0%
20%
0%
20%
0%

16V
6.3V
16V
6.3V
16V

C3026
C3027
C3028
C3030
C3031

1-117-919-11
1-107-820-11
1-110-569-11
1-119-750-11
1-125-777-11

TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP

10uF
0.1uF
47uF
22uF
0.1uF

20%
0%
20%
20%
10%

6.3V
16V
6.3V
6.3V
10V

C3032
C3033
C3034
C3035
C3036

1-117-919-11
1-135-337-11
1-119-750-11
1-135-337-11
1-117-919-11

TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP

10uF
1uF
22uF
1uF
10uF

20%
20%
20%
20%
20%

6.3V
6.3V
6.3V
6.3V
6.3V

C3037
C3038
C3039
C3040
C3041

1-107-826-91
1-107-826-91
1-164-874-11
1-125-926-91
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

0.1uF
0.1uF
100PF
4.7uF
0.1uF

10%
10%
5%
20%
0%

16V
16V
16V
6.3V
16V

MAIN
Ref. No.

Part No.

Description

Remark

C3042
C3043
C3044
C3045
C3046

1-107-820-11
1-107-820-11
1-117-919-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
10uF
0.1uF
0.1uF

0%
0%
20%
0%
0%

16V
16V
6.3V
16V
16V

C3047
C3048
C3049
C3050
C3051

1-107-820-11
1-125-777-11
1-107-820-11
1-107-820-11
1-119-750-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP

0.1uF
0.1uF
0.1uF
0.1uF
22uF

0%
10%
0%
0%
20%

16V
10V
16V
16V
6.3V

C3052
C3053
C3055
C4001
C4002

1-107-820-11
1-117-919-11
1-164-943-11
1-104-851-11
1-104-851-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP

0.1uF
10uF
0.01uF
10uF
10uF

0%
20%
10%
20%
20%

16V
6.3V
16V
10V
10V

C4003
C4004
C4005
C4006
C4007

1-104-851-11
1-119-749-11
1-125-777-11
1-135-181-21
1-135-181-21

TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP

10uF
33uF
0.1uF
4.7uF
4.7uF

20%
20%
10%
20%
20%

10V
4V
10V
6.3V
6.3V

C4008
C4009
C4010
C4011
C4012

1-125-777-11
1-164-943-11
1-125-899-11
1-119-749-11
1-125-777-11

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP

0.1uF
0.01uF
220uF
33uF
0.1uF

10%
10%
20%
20%
10%

10V
16V
4V
4V
10V

C4013
C4014
C4015
C4017
C4018

1-135-181-21
1-135-181-21
1-125-777-11
1-104-847-11
1-125-899-11

TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP

4.7uF
4.7uF
0.1uF
22uF
220uF

20%
20%
10%
20%
20%

6.3V
6.3V
10V
4V
4V

C4019
C4020
C4021
C4022
C4023

1-125-777-11
1-125-777-11
1-125-777-11
1-135-337-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
1uF
0.1uF

10%
10%
10%
20%
0%

10V
10V
10V
6.3V
16V

C4024
C4026
C4027
C4028
C4029

1-115-467-11
1-107-820-11
1-107-820-11
1-115-467-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.22uF
0.1uF
0.1uF
0.22uF
0.1uF

10%
0%
0%
10%
0%

10V
16V
16V
10V
16V

C4031
C4032
C5001
C5002
C5003

1-107-820-11
1-107-820-11
1-164-937-11
1-107-820-11
1-119-750-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP

0.1uF
0.1uF
0.001uF
0.1uF
22uF

0%
0%
10%
0%
20%

16V
16V
16V
16V
6.3V

C5004
C5005
C5006
C5007
C5008

1-107-820-11
1-119-750-11
1-125-777-11
1-125-777-11
1-164-943-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
22uF
0.1uF
0.1uF
0.01uF

0%
20%
10%
10%
10%

16V
6.3V
10V
10V
16V

C5009
C5011
C5012
C5013
C5014

1-164-943-11
1-113-985-11
1-125-777-11
1-125-777-11
1-125-837-91

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.01uF
10uF
0.1uF
0.1uF
1uF

10%
20%
10%
10%
10%

16V
20V
10V
10V
6.3V

C5015
C5016

1-107-819-11 CERAMIC CHIP
1-164-943-11 CERAMIC CHIP

0.022uF
0.01uF

10%
10%

16V
16V

Ref. No.

6-6

Part No.

Description

Remark

C5017
C5018
C5019

1-115-467-11 CERAMIC CHIP
1-164-942-11 CERAMIC CHIP
1-119-923-81 CERAMIC CHIP

0.22uF
10%
0.0068uF 10%
0.047uF 10%

10V
16V
10V

C5020
C5021
C5022
C5023
C5024

1-164-938-11
1-164-943-11
1-125-837-91
1-110-563-11
1-164-677-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.0015uF
0.01uF
1uF
0.068uF
0.033uF

10%
10%
10%
10%
10%

16V
16V
6.3V
16V
16V

C5025
C5026
C5027
C5028
C5029

1-107-820-11
1-104-851-11
1-107-820-11
1-107-820-11
1-164-943-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
10uF
0.1uF
0.1uF
0.01uF

0%
20%
0%
0%
10%

16V
10V
16V
16V
16V

C5030
C5031
C5032
C5033
C5034

1-164-943-11
1-125-777-11
1-107-820-11
1-107-820-11
1-119-923-81

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.01uF
0.1uF
0.1uF
0.1uF
0.047uF

10%
10%
0%
0%
10%

16V
10V
16V
16V
10V

C5035
C5036
C5037
C5038
C5039

1-107-820-11
1-107-820-11
1-107-820-11
1-164-943-11
1-119-923-81

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.01uF
0.047uF

0%
0%
0%
10%
10%

16V
16V
16V
16V
10V

C5040
C5041
C5042
C5043
C5044

1-125-777-11
1-107-820-11
1-164-870-11
1-164-862-11
1-125-777-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
68PF
33PF
0.1uF

10%
0%
5%
5%
10%

10V
16V
16V
16V
10V

C5045
C5046
C5047
C5048
C5049

1-107-820-11
1-164-870-11
1-164-862-11
1-125-777-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
68PF
33PF
0.1uF
0.1uF

0%
5%
5%
10%
0%

16V
16V
16V
10V
16V

C5051
C5052
C5055
C5056
C5057

1-107-820-11
1-107-820-11
1-125-777-11
1-107-819-11
1-107-819-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.022uF
0.022uF

0%
0%
10%
10%
10%

16V
16V
10V
16V
16V

C5101
C5102
C5103
C5104
C5105

1-125-777-11
1-125-837-91
1-164-943-11
1-164-943-11
1-104-851-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP

0.1uF
1uF
0.01uF
0.01uF
10uF

10%
10%
10%
10%
20%

10V
6.3V
16V
16V
10V

C5106
C5201
C5202
C5203
C5204

1-107-820-11
1-107-826-91
1-107-826-91
1-107-820-11
1-164-850-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
10PF

0%
10%
10%
0%
0.5PF

16V
16V
16V
16V
16V

C5205
C5206
C5207
C5208
C5209

1-164-850-11
1-164-940-11
1-164-940-11
1-125-777-11
1-125-777-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

10PF
0.0033uF
0.0033uF
0.1uF
0.1uF

0.5PF
10%
10%
10%
10%

16V
16V
16V
10V
10V

C5212
C5301
C5302
C5303
C5304

1-107-820-11
1-110-569-11
1-119-750-11
1-107-820-11
1-125-777-11

CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
47uF
22uF
0.1uF
0.1uF

0%
20%
20%
0%
10%

16V
6.3V
6.3V
16V
10V

MAIN
Ref. No.

Part No.

Description

Remark

C5305
C5306
C5307
C5308
C5309

1-107-820-11
1-125-777-11
1-164-847-11
1-164-677-11
1-164-847-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
7PF
0.033uF
7PF

0%
10%
0.5PF
10%
0.5PF

16V
10V
16V
16V
16V

C5310
C5311
C5312
C5313
C5314

1-125-891-11
1-107-820-11
1-164-939-11
1-164-874-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.47uF
0.1uF
0.0022uF
100PF
0.1uF

10%
0%
10%
5%
0%

10V
16V
16V
16V
16V

C5315
C5316
C5317
C5318
C5319

1-125-891-11
1-164-943-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.47uF
0.01uF
0.1uF
0.1uF
0.1uF

10%
10%
0%
0%
0%

10V
16V
16V
16V
16V

C5401
C5402
C5403
C5404
C5405

1-125-777-11
1-125-777-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

10%
10%
0%
0%
0%

10V
10V
16V
16V
16V

C5406
C5407
C5408
C5409
C5410

1-107-820-11
1-107-820-11
1-107-820-11
1-164-845-11
1-164-845-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
5PF
5PF

0%
16V
0%
16V
0%
16V
0.25PF 16V
0.25PF 16V

C5411
C5412
C5413
C5414
C5415

1-107-820-11
1-107-820-11
1-107-820-11
1-119-750-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
22uF
0.1uF

0%
0%
0%
20%
0%

C5417
C5418
C5419
C5420
C5421

1-164-845-11
1-164-943-11
1-107-820-11
1-107-820-11
1-164-850-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

5PF
0.01uF
0.1uF
0.1uF
10PF

0.25PF 16V
10%
16V
0%
16V
0%
16V
0.5PF 16V

C5424
C5501
C5503
C5601
C5602

1-164-842-11
1-107-820-11
1-107-820-11
1-125-777-11
1-119-751-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP

2PF
0.1uF
0.1uF
0.1uF
22uF

0.25PF 16V
0%
16V
0%
16V
10%
10V
20%
16V

C5603
C5604
C5605
C5606
C5607

1-107-820-11
1-104-912-11
1-113-985-11
1-104-912-11
1-104-912-11

CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP

0.1uF
3.3uF
10uF
3.3uF
3.3uF

0%
20%
20%
20%
20%

16V
16V
20V
16V
16V

C5608
C5609
C5610
C5614
C5615

1-104-912-11
1-113-682-11
1-113-682-11
1-113-642-11
1-164-874-11

TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP

3.3uF
33uF
33uF
47uF
100PF

20%
20%
20%
20%
5%

16V
10V
10V
10V
16V

C8001
C8002
C8003
C8004
C8005

1-119-750-11
1-107-820-11
1-164-847-11
1-164-847-11
1-107-820-11

TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

22uF
0.1uF
7PF
7PF
0.1uF

20%
0%
0.5PF
0.5PF
0%

6.3V
16V
16V
16V
16V

C8006
C8007

1-107-820-11 CERAMIC CHIP
1-107-820-11 CERAMIC CHIP

0.1uF
0.1uF

0%
0%

16V
16V

Ref. No.

16V
16V
16V
6.3V
16V

6-7

Part No.

Description

Remark

C8008
C8009
C8010

1-107-820-11 CERAMIC CHIP
1-107-820-11 CERAMIC CHIP
1-107-820-11 CERAMIC CHIP

0.1uF
0.1uF
0.1uF

0%
0%
0%

16V
16V
16V

C8011
C8012
C8013
C8014
C8015

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

0%
0%
0%
0%
0%

16V
16V
16V
16V
16V

C8016
C8017
C8018
C8019
C8020

1-164-935-11
1-164-935-11
1-107-820-11
1-107-820-11
1-164-858-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

470PF
470PF
0.1uF
0.1uF
22PF

10%
10%
0%
0%
5%

16V
16V
16V
16V
16V

C8021
C8022
C8023
C8024
C8025

1-164-858-11
1-119-750-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

22PF
22uF
0.1uF
0.1uF
0.1uF

5%
20%
0%
0%
0%

16V
6.3V
16V
16V
16V

C8026
C8027
C8028
C8029
C8030

1-164-937-11
1-119-750-11
1-107-820-11
1-107-820-11
1-125-891-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.001uF
22uF
0.1uF
0.1uF
0.47uF

10%
20%
0%
0%
10%

16V
6.3V
16V
16V
10V

C8031
C8032
C8033
C8034
C8035

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-119-751-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP

0.1uF
0.1uF
0.1uF
0.1uF
22uF

0%
0%
0%
0%
20%

16V
16V
16V
16V
16V

C8036
C8037
C8038
C8039
C8040

1-107-820-11
1-107-820-11
1-115-565-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
2.2uF
0.1uF
0.1uF

0%
0%
10%
0%
0%

16V
16V
10V
16V
16V

C8041
C8042
C8043
C8044
C8045

1-107-820-11
1-107-820-11
1-119-750-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
22uF
0.1uF
0.1uF

0%
0%
20%
0%
0%

16V
16V
6.3V
16V
16V

C8046
C8047
C8048
C8049
C8050

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

0%
0%
0%
0%
0%

16V
16V
16V
16V
16V

C8051
C8052
C8053
C8055
C8056

1-107-820-11
1-107-820-11
1-164-874-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
100PF
0.1uF
0.1uF

0%
0%
5%
0%
0%

16V
16V
16V
16V
16V

C8057
C8059
C8062
C8063
C8064

1-125-777-11
1-107-820-11
1-125-777-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

10%
0%
10%
0%
0%

10V
16V
10V
16V
16V

C8065
C8067
C8068
C8069
C8070

1-107-820-11
1-107-820-11
1-164-845-11
1-107-820-11
1-119-750-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP

0.1uF
0.1uF
5PF
0.1uF
22uF

0%
16V
0%
16V
0.25PF 16V
0%
16V
20%
6.3V

MAIN
Ref. No.

Part No.

Description

Remark

C8071
C8072
C8073
C8074
C8075

1-164-937-11
1-107-820-11
1-119-750-11
1-104-851-11
1-113-985-11

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP

0.001uF
0.1uF
22uF
10uF
10uF

10%
0%
20%
20%
20%

16V
16V
6.3V
10V
20V

C8076
C8077
C8078
C8079
C8080

1-119-923-81
1-107-820-11
1-107-820-11
1-107-820-11
1-125-777-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.047uF
0.1uF
0.1uF
0.1uF
0.1uF

10%
0%
0%
0%
10%

10V
16V
16V
16V
10V

C8081
C8101
C8102
C8103
C8104

1-125-777-11
1-119-750-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
22uF
0.1uF
0.1uF
0.1uF

10%
20%
0%
0%
0%

10V
6.3V
16V
16V
16V

C8105
C8106
C8107
C8108
C8109

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-164-943-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.01uF

0%
0%
0%
0%
10%

16V
16V
16V
16V
16V

C8110
C8111
C8112
C8113
C8114

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

0%
0%
0%
0%
0%

16V
16V
16V
16V
16V

C8115
C8116
C8117
C8118
C8119

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

0%
0%
0%
0%
0%

16V
16V
16V
16V
16V

C8120
C8121
C8123
C8126
C8127

1-107-820-11
1-119-750-11
1-107-820-11
1-128-964-91
1-107-820-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

0.1uF
22uF
0.1uF
100uF
0.1uF

0%
20%
0%
20%
0%

16V
6.3V
16V
6.3V
16V

C8128
C8129
C8130
C8204
C8208

1-107-820-11
1-107-820-11
1-119-750-11
1-125-777-11
1-104-851-11

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP

0.1uF
0.1uF
22uF
0.1uF
10uF

0%
0%
20%
10%
20%

16V
16V
6.3V
10V
10V

C8211
C8501
C8502
C8503
C8504

1-117-919-11
1-119-750-11
1-107-820-11
1-107-820-11
1-107-820-11

TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

10uF
22uF
0.1uF
0.1uF
0.1uF

20%
20%
0%
0%
0%

6.3V
6.3V
16V
16V
16V

C8506
C8507
C8508
C8510
C8511

1-164-858-11
1-107-820-11
1-107-820-11
1-107-820-11
1-164-858-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

22PF
0.1uF
0.1uF
0.1uF
22PF

5%
0%
0%
0%
5%

16V
16V
16V
16V
16V

C8601
C8602
C8603
C8604
C8605

1-119-750-11
1-119-750-11
1-107-820-11
1-107-820-11
1-107-820-11

TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

22uF
22uF
0.1uF
0.1uF
0.1uF

20%
20%
0%
0%
0%

6.3V
6.3V
16V
16V
16V

C8606
C8607

1-107-820-11 CERAMIC CHIP
1-107-820-11 CERAMIC CHIP

0.1uF
0.1uF

0%
0%

16V
16V

Ref. No.

6-8

Part No.

Description

Remark

C8608
C8609
C8610

1-107-820-11 CERAMIC CHIP
1-164-937-11 CERAMIC CHIP
1-107-820-11 CERAMIC CHIP

0.1uF
0.001uF
0.1uF

0%
10%
0%

16V
16V
16V

C8611
C8612
C8613
C8614
C8615

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

0%
0%
0%
0%
0%

16V
16V
16V
16V
16V

C8616
C8617
C8618
C8619
C8620

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

0%
0%
0%
0%
0%

16V
16V
16V
16V
16V

C8621
C8622
C8623
C8624
C8701

1-107-820-11
1-107-820-11
1-107-820-11
1-119-750-11
1-119-750-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP

0.1uF
0.1uF
0.1uF
22uF
22uF

0%
0%
0%
20%
20%

16V
16V
16V
6.3V
6.3V

C8702
C8703
C8704
C8705
C8706

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

0%
0%
0%
0%
0%

16V
16V
16V
16V
16V

C8707
C8708
C8709
C8710
C8711

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

0%
0%
0%
0%
0%

16V
16V
16V
16V
16V

C8712
C8713
C8714
C8715
C8716

1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.1uF
0.1uF
0.1uF

0%
0%
0%
0%
0%

16V
16V
16V
16V
16V

C8717
C8718
C9101
C9103
C9104

1-107-820-11
1-119-750-11
1-164-004-11
1-107-820-11
1-125-777-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
22uF
0.1uF
0.1uF
0.1uF

0%
20%
10%
0%
10%

16V
6.3V
25V
16V
10V

C9105
C9106
C9107
C9108
C9109

1-125-777-11
1-125-777-11
1-164-943-11
1-125-777-11
1-107-820-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.1uF
0.01uF
0.1uF
0.1uF

10%
10%
10%
10%
0%

10V
10V
16V
10V
16V

C9110
C9111
C9112
C9113
C9114

1-104-916-11
1-104-752-11
1-164-943-11
1-125-777-11
1-117-919-11

TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP

6.8uF
33uF
0.01uF
0.1uF
10uF

20%
20%
10%
10%
20%

20V
6.3V
16V
10V
6.3V

C9115
C9116
C9117
C9118
C9119

1-117-919-11
1-125-777-11
1-164-004-11
1-107-819-11
1-135-213-21

TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP

10uF
0.1uF
0.1uF
0.022uF
3.3uF

20%
10%
10%
10%
20%

6.3V
10V
25V
16V
25V

C9120
C9121
C9122
C9123
C9126

1-117-919-11
1-117-919-11
1-119-750-11
1-164-004-11
1-125-777-11

TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP

10uF
10uF
22uF
0.1uF
0.1uF

20%
20%
20%
10%
10%

6.3V
6.3V
6.3V
25V
10V

MAIN
Ref. No.

Part No.

Description

C9127
C9128
C9129
C9130
C9131

1-117-919-11
1-107-820-11
1-107-820-11
1-107-820-11
1-119-750-11

TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP

C9132
C9133

1-107-820-11 CERAMIC CHIP
1-127-772-11 CERAMIC CHIP

Remark
10uF
0.1uF
0.1uF
0.1uF
22uF

20%
0%
0%
0%
20%

6.3V
16V
16V
16V
6.3V

0.1uF
0.033uF

0%
10%

16V
16V

Ref. No.
FB8019
FB8020
FB8021
FB8022

Part No.

Description

1-469-638-21
1-469-638-21
1-469-637-21
1-469-637-21

FERRITE
FERRITE
FERRITE
FERRITE

Remark
0uH
0uH
0uH
0uH

< FILTER >
FL4001 1-233-732-21 FILTER, BAND PASS
FL4002 1-233-733-21 FILTER, LOW PASS
FL5101 1-234-255-21 FILTER, LOW PASS

< CONNECTOR >
< IC >
CN3001
CN3002
* CN4312
CN4313
CN4511

1-778-507-21
1-778-591-21
1-785-283-41
1-785-283-21
1-784-651-11

PIN, CONNECTOR (PC BOARD) 4P
CONNECTOR, BOARD TO BOARD 30P
PIN, CONNECTOR (PC BOARD) 14P
PIN, CONNECTOR (PC BOARD) 14P
CONNECTOR, FFC/FPC (ZIF) 27P

CN5001
CN5002
CN8001
CN8002
CN8003

1-784-422-11
1-778-597-21
1-778-595-21
1-573-916-11
1-573-915-11

CONNECTOR, FFC/FPC (ZIF) 33P
CONNECTOR, BOARD TO BOARD 50P
CONNECTOR, BOARD TO BOARD 20P
CONNECTOR, FFC/FPC (ZIF) 7P
CONNECTOR, FFC/FPC (ZIF) 6P

CN8006
CN8007
CN8101
* CN9101

1-573-915-11
1-778-593-21
1-778-803-11
1-785-481-41

CONNECTOR, FFC/FPC (ZIF) 6P
CONNECTOR, BOARD TO BOARD 60P
CONNECTOR, BOARD TO BOARD 40P
CONNECTOR, BOARD TO BOARD 70P

IC3001
IC3002
IC3003
IC3004
IC3005

8-759-380-80
8-759-536-71
8-759-488-29
8-759-584-59
8-759-058-58

IC
IC
IC
IC
IC

LA7473V-TLM
TLV23621PWR
TC7W66FU (TE12R)
AK4517A-VQ-L
TC7S04FU (TE85R)

IC3007
IC3008
IC3009
IC4001
IC4002

8-759-584-58
8-759-649-95
8-752-397-21
8-759-571-31
8-759-571-31

IC
IC
IC
IC
IC

AN7535NSA-E1
LM4881MMX
CXZ31021GA
TK15406M-1TL
TK15406M-1TL

< DIODE >

IC4003
IC4004
IC4005
IC4006
IC4007

8-759-571-32
8-759-571-31
8-759-540-53
8-759-566-06
8-759-497-44

IC
IC
IC
IC
IC

TK15405M-1TL
TK15406M-1TL
BA7664FV-E2
TC7WH08FU (TE12R)
TC7WH125FU (TE12R)

D4001
D4003
D5601
D5602
D8001

8-719-056-48
8-719-056-48
8-719-046-85
8-719-067-36
8-719-046-91

DIODE
DIODE
DIODE
DIODE
DIODE

1SS388 (TPL3)
1SS388 (TPL3)
MA2S728
MA3ZD1200LS0
MA2S111

IC4008
IC4009
IC4010
IC4011
IC5002

8-759-497-44
8-759-566-06
8-759-497-44
8-759-497-44
8-752-081-97

IC
IC
IC
IC
IC

TC7WH125FU (TE12R)
TC7WH08FU (TE12R)
TC7WH125FU (TE12R)
TC7WH125FU (TE12R)
CXA2524R

D8002
D8003
D8005
D8006
D8007

8-719-046-85
8-719-046-91
8-719-046-85
8-719-056-48
8-719-056-48

DIODE
DIODE
DIODE
DIODE
DIODE

MA2S728
MA2S111
MA2S728
1SS388 (TPL3)
1SS388 (TPL3)

IC5003
IC5004
IC5005
IC5006
IC5007

8-759-449-58
8-759-273-87
8-759-572-28
8-759-572-28
8-759-082-61

IC
IC
IC
IC
IC

LM7131BCM5X
NJM2901V (TE2)
NJU7016R
NJU7016R
TC4W53FU

IC5008
IC5009
IC5010
IC5011
IC5012

8-759-082-58
8-759-572-34
8-759-572-34
8-759-572-34
8-759-572-34

IC
IC
IC
IC
IC

TC7W08FU
LMV821M7X
LMV821M7X
LMV821M7X
LMV821M7X

IC5013
IC5014
IC5015
IC5102
IC5201

8-759-082-55
8-759-082-55
8-759-058-58
8-752-371-18
8-759-572-38

IC
IC
IC
IC
IC

TC7W00FU
TC7W00FU
TC7S04FU (TE85R)
CXD2302Q
NJM2140R

IC5205
IC5301
IC5302
IC5303
IC5401

8-759-572-35
8-752-397-34
8-759-196-96
8-759-196-96
8-759-572-34

IC
IC
IC
IC
IC

TLC3702CPWR
CXD2652AGA
TC7SH08FU-TE85R
TC7SH08FU-TE85R
LMV821M7X

IC5402
IC5403
IC5404
IC5405
IC5406

8-759-196-96
8-752-390-38
8-759-676-88
8-759-449-23
8-759-559-93

IC
IC
IC
IC
IC

TC7SH08FU-TE85R
CXD606-112GA
RU6815TC-DCMM1
AK93C55AV-L
S-8110ANP-DSB-T2

IC5407
IC5408

8-759-443-08 IC TC7W241FU-TE12R
8-759-082-61 IC TC4W53FU

< FERRITE BEAD >
* FB3001 1-469-092-11
* FB3002 1-469-092-11
FB8001 1-469-638-21
FB8002 1-469-638-21
FB8003 1-469-638-21

FERRITE
FERRITE
FERRITE
FERRITE
FERRITE

0uH
0uH
0uH
0uH
0uH

FB8004
FB8005
FB8006
FB8007
FB8008

1-469-638-21
1-469-638-21
1-469-638-21
1-469-638-21
1-469-638-21

FERRITE
FERRITE
FERRITE
FERRITE
FERRITE

0uH
0uH
0uH
0uH
0uH

FB8009
FB8010
FB8011
FB8012
FB8013

1-469-638-21
1-469-638-21
1-469-638-21
1-469-638-21
1-469-638-21

FERRITE
FERRITE
FERRITE
FERRITE
FERRITE

0uH
0uH
0uH
0uH
0uH

FB8014
FB8015
FB8016
FB8017
FB8018

1-469-638-21
1-469-638-21
1-469-638-21
1-469-638-21
1-469-638-21

FERRITE
FERRITE
FERRITE
FERRITE
FERRITE

0uH
0uH
0uH
0uH
0uH

6-9

MAIN
Ref. No.

Part No.

Description

Remark

IC5501
IC5601
IC5602

8-759-572-37 IC KM68V1002AT-12
8-759-482-07 IC MPC17A28SVMEL
8-759-460-34 IC MPC17A36VMEL

IC5603
IC8001
IC8002
IC8003
IC8004

8-759-578-53
8-759-572-52
8-759-572-70
8-759-572-70
8-759-676-89

IC
IC
IC
IC
IC

XC6365D103MR
HD6417709BT80A
KM416S4034CC-C10
KM416S4034CC-C10
HN58V1001T-25-DCMM1

IC8005
IC8006
IC8007
IC8008
IC8009

1-803-635-11
8-759-196-97
8-759-196-97
8-759-560-17
8-759-578-13

IC
IC
IC
IC
IC

WTGA-EKM29U64000-K1
TC7SH32FU-TE85R
TC7SH32FU-TE85R
RS5C348A-E2
PST9329UL

IC8010
IC8011
IC8012
IC8013
IC8015

8-759-196-97
8-759-573-16
8-759-656-85
8-759-058-54
8-759-082-55

IC
IC
IC
IC
IC

TC7SH32FU-TE85R
S-81232SG-Q4-T1
XC62EP3202MR
TC7S00FU (TE85R)
TC7W00FU

IC8016
IC8020
IC8023
IC8024
IC8025

8-759-195-81
8-759-523-11
8-759-531-92
8-759-196-96
8-759-196-96

IC
IC
IC
IC
IC

TC7S86FU
TC74AC74FT (EL)
TC7WH04FU (TE12R)
TC7SH08FU-TE85R
TC7SH08FU-TE85R

IC8026
IC8027
IC8101
IC8102
IC8103

8-759-196-96
8-759-642-45
8-752-396-85
8-759-572-71
8-759-572-71

IC
IC
IC
IC
IC

TC7SH08FU-TE85R
TL1596CPW-ELM2000
CXD702-102GA
KM416U4104BC-L6
KM416U4104BC-L6

IC8104
IC8202
IC8501
IC8601
IC8602

8-759-523-11
8-759-325-27
8-759-653-48
8-752-396-81
8-759-596-11

IC
IC
IC
IC
IC

TC74AC74FT (EL)
TK11231AMTL
uPD70F3102AF1-33-FA1
CXD1405GG
KM432S2030CT-G8

IC8701
IC8702
IC8703
IC9102
IC9103

8-752-394-48
8-759-572-69
8-759-572-69
8-759-252-41
8-759-426-83

IC
IC
IC
IC
IC

CXD1404GA
KM416U1204CC-L6
KM416U1204CC-L6
TK11900MTL
TK11228BMCL

IC9104

8-759-426-83 IC TK11228BMCL

Ref. No.

Part No.

Description

L5601
L5602
L5603
L5604

1-414-407-41
1-412-056-11
1-412-056-11
1-412-056-11

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

330uH
4.7uH
4.7uH
4.7uH

Remark

L5605
L5606
L5607
L5610
L8001

1-412-056-11
1-410-389-31
1-410-389-31
1-416-346-11
1-414-754-11

INDUCTOR
INDUCTOR CHIP
INDUCTOR CHIP
INDUCTOR
INDUCTOR

4.7uH
47uH
47uH
33uH
10uH

L8002
L8003
L8004
L8101
L8102

1-414-754-11
1-414-398-11
1-414-394-41
1-412-028-11
1-414-754-11

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR CHIP
INDUCTOR

10uH
10uH
2.2uH
4.7uH
10uH

L8103
L8104
L8202
L8501
L8601

1-414-754-11
1-414-398-11
1-414-754-11
1-469-367-21
1-414-398-11

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

10uH
10uH
10uH
10uH
10uH

L8602
L8603
L8701
L8702
L9102

1-414-398-11
1-414-398-11
1-469-367-21
1-414-398-11
1-414-404-41

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

10uH
10uH
10uH
10uH
100uH

L9103
L9104
L9105

1-414-404-41 INDUCTOR
1-414-398-11 INDUCTOR
1-414-398-11 INDUCTOR

100uH
10uH
10uH

< TRANSISTOR >

< COIL >
L3001
L3002
L3003
L3004
L3005

1-414-754-11
1-414-754-11
1-414-398-11
1-414-398-11
1-414-754-11

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

10uH
10uH
10uH
10uH
10uH

L3006
L4001
L4002
L4003
L5001

1-414-398-11
1-414-754-11
1-414-754-11
1-414-754-11
1-414-398-11

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

10uH
10uH
10uH
10uH
10uH

L5002
L5101
L5301
L5401
L5402

1-414-754-11
1-414-398-11
1-414-754-11
1-412-939-11
1-414-398-11

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

10uH
10uH
10uH
1uH
10uH

L5403

1-410-985-42 INDUCTOR CHIP 0.22uH

6-10

Q3001

8-759-426-37 TRANSISTOR

Q3002
Q3003
Q3004
Q4001

8-729-037-52
8-729-047-37
8-729-047-68
8-729-037-53

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

MC68HC05G6PBSC430917PB
2SD2216J-QR (TX).SO
FDN338P
SSM3K03FE (TPL3)
2SB1462J-QR (TX).SO

Q4002
Q4003
Q4004
Q4005
Q4006

8-729-037-53
8-729-037-67
8-729-037-74
8-729-427-70
8-729-427-70

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

2SB1462J-QR (TX).SO
UN9119J- (TX).SO
UN9213J- (TX).SO
XP4401
XP4401

Q4007
Q5001
Q5002
Q5003
Q5004

8-729-427-70
8-729-429-50
8-729-037-89
8-729-047-36
8-729-037-73

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

XP4401
XP4312
2SC4627J-C (TX).SO
CPH3303-TL
UN9212J- (TX).SO

Q5005
Q5009
Q5010
Q5101
Q5102

8-729-426-22
8-729-047-36
8-729-037-73
8-729-427-74
8-729-047-36

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

XP1211
CPH3303-TL
UN9212J- (TX).SO
XP4601
CPH3303-TL

Q5201
Q5202
Q5203
Q5204
Q5601

8-729-427-72
8-729-427-70
8-729-047-36
8-729-037-73
8-729-047-90

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

XP4501
XP4401
CPH3303-TL
UN9212J- (TX).SO
XP162A11C0PR

Q5602
Q5603
Q8001

8-729-037-61 TRANSISTOR
8-729-037-73 TRANSISTOR
8-729-037-53 TRANSISTOR

UN9113J- (TX).SO
UN9212J- (TX).SO
2SB1462J-QR (TX).SO

MAIN
Ref. No.

Part No.

Description

Remark

Q8002
Q8003

8-729-043-94 TRANSISTOR
8-729-044-20 TRANSISTOR

CPH3106-PM-TL
SI6463DQ-T1

Q8004
Q8005
Q8006
Q8007
Q8008

8-729-044-20
8-729-037-53
8-729-047-68
8-729-044-20
8-729-044-20

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

SI6463DQ-T1
2SB1462J-QR (TX).SO
SSM3K03FE (TPL3)
SI6463DQ-T1
SI6463DQ-T1

Q8009
Q8010
Q8011
Q8012
Q8013

8-729-047-68
8-729-032-62
8-729-032-62
8-729-047-68
8-729-047-68

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

SSM3K03FE (TPL3)
2SJ347-TE85L
2SJ347-TE85L
SSM3K03FE (TPL3)
SSM3K03FE (TPL3)

Q8014
Q9101
Q9102
Q9103
Q9104

8-729-047-68
8-729-427-72
8-729-037-52
8-729-047-68
8-729-427-70

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

SSM3K03FE (TPL3)
XP4501
2SD2216J-QR (TX).SO
SSM3K03FE (TPL3)
XP4401

Q9105
Q9107
Q9108
Q9110
Q9111

8-729-041-23
8-729-047-37
8-729-047-68
8-729-047-68
8-729-427-70

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

NDS356AP
FDN338P
SSM3K03FE (TPL3)
SSM3K03FE (TPL3)
XP4401

Q9112
Q9113
Q9115
Q9116
Q9117

8-729-047-68
8-729-047-68
8-729-042-82
8-729-047-68
8-729-041-23

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

SSM3K03FE (TPL3)
SSM3K03FE (TPL3)
NDH834P
SSM3K03FE (TPL3)
NDS356AP

Q9122
Q9125
Q9126

8-729-047-37 TRANSISTOR
8-729-037-74 TRANSISTOR
8-729-032-62 TRANSISTOR

Ref. No.

FDN338P
UN9213J- (TX).SO
2SJ347-TE85L

< RESISTOR >
R1001
R1002
R1003
R1004
R1005

1-218-963-11
1-218-957-11
1-218-959-11
1-218-947-11
1-218-965-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

6.8K
2.2K
3.3K
330
10K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R1006
R1007
R1008
R1009
R1010

1-218-963-11
1-218-963-11
1-218-971-11
1-218-971-11
1-218-969-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

6.8K
6.8K
33K
33K
22K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R1011
R1012
R1013
R1014
R1015

1-218-971-11
1-218-969-11
1-218-961-11
1-218-963-11
1-218-973-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

33K
22K
4.7K
6.8K
47K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R1016
R1017
R1019
R1021
R1022

1-208-691-11
1-208-927-11
1-218-990-11
1-208-927-11
1-218-965-11

METAL CHIP
METAL CHIP
SHORT
METAL CHIP
RES, CHIP

2.2K
47K
0
47K
10K

0.5%
0.5%

1/16W
1/16W

0.5%
5%

1/16W
1/16W

R1023
R1024
R1025
R1026
R1027

1-218-965-11
1-208-927-11
1-218-446-11
1-218-990-11
1-218-849-11

RES, CHIP
METAL CHIP
METAL CHIP
SHORT
METAL CHIP

10K
47K
1
0
3.3K

5%
0.5%
5%

1/16W
1/16W
1/16W

0.5%

1/16W

6-11

Part No.

Description

R1028
R1029
R1030
R1032
R2001

1-218-975-11
1-218-973-11
1-208-675-11
1-218-955-11
1-218-963-11

RES, CHIP
RES, CHIP
METAL CHIP
RES, CHIP
RES, CHIP

68K
47K
470
1.5K
6.8K

5%
5%
0.5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

Remark

R2002
R2003
R2004
R2005
R2006

1-218-957-11
1-218-959-11
1-218-947-11
1-218-965-11
1-218-963-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

2.2K
3.3K
330
10K
6.8K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R2007
R2008
R2009
R2010
R2011

1-218-963-11
1-218-971-11
1-218-971-11
1-218-969-11
1-218-971-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

6.8K
33K
33K
22K
33K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R2012
R2013
R2014
R2015
R2016

1-218-969-11
1-218-961-11
1-218-963-11
1-218-973-11
1-208-691-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
METAL CHIP

22K
4.7K
6.8K
47K
2.2K

5%
5%
5%
5%
0.5%

1/16W
1/16W
1/16W
1/16W
1/16W

R2017
R2019
R2021
R2022
R2023

1-208-927-11
1-218-990-11
1-208-927-11
1-218-965-11
1-218-965-11

METAL CHIP
SHORT
METAL CHIP
RES, CHIP
RES, CHIP

47K
0
47K
10K
10K

0.5%

1/16W

0.5%
5%
5%

1/16W
1/16W
1/16W

R2024
R2025
R2026
R2027
R2028

1-208-927-11
1-218-446-11
1-218-990-11
1-218-849-11
1-218-975-11

METAL CHIP
METAL CHIP
SHORT
METAL CHIP
RES, CHIP

47K
1
0
3.3K
68K

0.5%
5%

1/16W
1/16W

0.5%
5%

1/16W
1/16W

R2029
R2030
R2032
R3001
R3002

1-218-973-11
1-208-675-11
1-218-955-11
1-218-981-11
1-216-150-91

RES, CHIP
METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP

47K
470
1.5K
220K
10

5%
0.5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/8W

R3004
R3005
R3006
R3009
R3010

1-218-977-11
1-218-989-11
1-218-446-11
1-218-965-11
1-218-965-11

RES, CHIP
RES, CHIP
METAL CHIP
RES, CHIP
RES, CHIP

100K
1M
1
10K
10K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R3011
R3013
R3014
R3015
R3016

1-218-969-11
1-218-979-11
1-218-989-11
1-218-989-11
1-218-965-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

22K
150K
1M
1M
10K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R3018
R3019
R3022
R3023
R4001

1-218-975-11
1-218-969-11
1-218-990-11
1-218-983-11
1-218-941-11

RES, CHIP
RES, CHIP
SHORT
RES, CHIP
METAL CHIP

68K
22K
0
330K
100

5%
5%

1/16W
1/16W

5%
0.5%

1/16W
1/16W

R4002
R4003
R4004
R4005
R4006

1-208-671-11
1-208-683-11
1-208-683-11
1-218-957-11
1-218-941-11

METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP
METAL CHIP

330
1K
1K
2.2K
100

0.5%
0.5%
0.5%
5%
0.5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4007
R4008
R4009

1-208-671-11 METAL CHIP
1-208-683-11 METAL CHIP
1-208-683-11 METAL CHIP

330
1K
1K

0.5%
0.5%
0.5%

1/16W
1/16W
1/16W

MAIN
Ref. No.

Part No.

Description

Remark

R4010
R4011

1-218-957-11 RES, CHIP
1-208-675-11 METAL CHIP

2.2K
470

5%
0.5%

1/16W
1/16W

R4012
R4013
R4014
R4015
R4016

1-218-941-11
1-218-957-11
1-218-957-11
1-218-957-11
1-218-957-11

METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

100
2.2K
2.2K
2.2K
2.2K

0.5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4017
R4018
R4019
R4020
R4021

1-218-957-11
1-218-957-11
1-218-990-11
1-218-990-11
1-218-990-11

RES, CHIP
RES, CHIP
SHORT
SHORT
SHORT

2.2K
2.2K
0
0
0

5%
5%

1/16W
1/16W

R4022
R4026
R4028
R4030
R4031

1-218-990-11
1-218-985-11
1-218-985-11
1-218-965-11
1-218-965-11

SHORT
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

0
470K
470K
10K
10K

5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W

R5001
R5003
R5004
R5005
R5006

1-218-945-11
1-218-985-11
1-218-957-11
1-218-957-11
1-218-987-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

220
470K
2.2K
2.2K
680K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5007
R5008
R5009
R5010
R5011

1-218-973-11
1-218-973-11
1-218-953-11
1-218-965-11
1-218-987-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

47K
47K
1K
10K
680K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5012
R5013
R5014
R5015
R5016

1-218-977-11
1-218-957-11
1-218-977-11
1-218-965-11
1-218-953-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

100K
2.2K
100K
10K
1K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5017
R5018
R5020
R5021
R5022

1-218-949-11
1-218-949-11
1-218-951-11
1-218-951-11
1-218-990-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
SHORT

470
470
680
680
0

5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W

R5023
R5024
R5025
R5026
R5027

1-218-953-11
1-218-965-11
1-218-981-11
1-218-977-11
1-218-975-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
10K
220K
100K
68K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5028
R5030
R5031
R5032
R5033

1-218-965-11
1-218-965-11
1-218-965-11
1-218-977-11
1-218-977-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

10K
10K
10K
100K
100K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5034
R5037
R5038
R5039
R5040

1-218-953-11
1-218-985-11
1-218-985-11
1-218-967-11
1-218-967-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
470K
470K
15K
15K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5041
R5042
R5043
R5044
R5045

1-218-965-11
1-218-967-11
1-218-965-11
1-218-985-11
1-218-965-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

10K
15K
10K
470K
10K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

Ref. No.

6-12

Part No.

Description

R5046
R5047
R5048
R5049
R5050

1-218-985-11
1-218-965-11
1-218-965-11
1-218-973-11
1-218-973-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

470K
10K
10K
47K
47K

5%
5%
5%
5%
5%

Remark
1/16W
1/16W
1/16W
1/16W
1/16W

R5051
R5052
R5053
R5054
R5055

1-218-961-11
1-218-977-11
1-218-977-11
1-218-973-11
1-218-977-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

4.7K
100K
100K
47K
100K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5056
R5057
R5058
R5059
R5060

1-218-977-11
1-218-973-11
1-218-977-11
1-218-990-11
1-218-990-11

RES, CHIP
RES, CHIP
RES, CHIP
SHORT
SHORT

100K
47K
100K
0
0

5%
5%
5%

1/16W
1/16W
1/16W

R5061
R5076
R5077
R5078
R5101

1-218-990-11
1-218-989-11
1-218-989-11
1-218-957-11
1-218-953-11

SHORT
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

0
1M
1M
2.2K
1K

5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W

R5102
R5103
R5104
R5105
R5106

1-218-953-11
1-218-941-11
1-218-953-11
1-218-953-11
1-218-989-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
100
1K
1K
1M

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5107
R5112
R5113
R5201
R5202

1-218-989-11
1-218-981-11
1-218-977-11
1-218-953-11
1-218-953-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1M
220K
100K
1K
1K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5203
R5204
R5205
R5206
R5207

1-218-953-11
1-218-953-11
1-218-971-11
1-218-971-11
1-218-977-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
1K
33K
33K
100K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5208
R5209
R5210
R5211
R5214

1-218-977-11
1-218-977-11
1-218-977-11
1-218-981-11
1-218-989-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

100K
100K
100K
220K
1M

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5215
R5216
R5217
R5301
R5302

1-218-989-11
1-218-990-11
1-218-990-11
1-218-935-11
1-218-959-11

RES, CHIP
SHORT
SHORT
RES, CHIP
RES, CHIP

1M
0
0
33
3.3K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5303
R5304
R5305
R5306
R5307

1-218-965-11
1-218-971-11
1-218-989-11
1-218-975-11
1-218-975-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

10K
33K
1M
68K
68K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5308
R5309
R5310
R5311
R5312

1-218-961-11
1-218-985-11
1-218-961-11
1-218-977-11
1-218-965-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

4.7K
470K
4.7K
100K
10K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5313
R5314
R5316

1-216-801-11 METAL CHIP
1-218-937-11 RES, CHIP
1-218-959-11 RES, CHIP

22
47
3.3K

5%
5%
5%

1/16W
1/16W
1/16W

MAIN
Ref. No.

Part No.

Description

Remark

R5318
R5401

1-218-990-11 SHORT
1-218-965-11 RES, CHIP

0
10K

5%

1/16W

R5402
R5403
R5404
R5405
R5406

1-218-965-11
1-218-983-11
1-218-983-11
1-218-983-11
1-218-983-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

10K
330K
330K
330K
330K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5407
R5408
R5409
R5410
R5411

1-218-983-11
1-218-983-11
1-208-707-11
1-208-719-11
1-218-973-11

RES, CHIP
RES, CHIP
METAL CHIP
METAL CHIP
RES, CHIP

330K
330K
10K
33K
47K

5%
5%
0.5%
0.5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5412
R5413
R5414
R5416
R5417

1-218-985-11
1-218-983-11
1-218-983-11
1-208-663-11
1-218-937-11

RES, CHIP
RES, CHIP
RES, CHIP
METAL CHIP
RES, CHIP

470K
330K
330K
150
47

5%
5%
5%
0.5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R5418
R5419
R5420
R5421
R5422

1-218-983-11
1-218-989-11
1-218-939-11
1-218-989-11
1-218-990-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
SHORT

330K
1M
68
1M
0

5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W

R5423
R5424
R5425
R5426
R5427

1-218-990-11
1-218-985-11
1-218-990-11
1-218-941-11
1-218-941-11

SHORT
RES, CHIP
SHORT
METAL CHIP
METAL CHIP

0
470K
0
100
100

R5428
R5429
R5601
R5602
R5603

1-218-941-11
1-218-941-11
1-218-990-11
1-218-977-11
1-218-985-11

METAL CHIP
METAL CHIP
SHORT
RES, CHIP
RES, CHIP

R5604
R5605
R5606
R5607
R8001

1-218-989-11
1-218-990-11
1-218-983-11
1-218-990-11
1-218-977-11

R8002
R8003
R8004
R8005
R8006

5%

1/16W

0.5%
0.5%

1/16W
1/16W

100
100
0
100K
470K

0.5%
0.5%

1/16W
1/16W

5%
5%

1/16W
1/16W

RES, CHIP
SHORT
RES, CHIP
SHORT
RES, CHIP

1M
0
330K
0
100K

5%

1/16W

5%

1/16W

5%

1/16W

1-218-953-11
1-218-953-11
1-218-953-11
1-218-953-11
1-218-953-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
1K
1K
1K
1K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8007
R8008
R8009
R8010
R8011

1-218-985-11
1-218-985-11
1-218-985-11
1-218-985-11
1-218-985-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

470K
470K
470K
470K
470K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8012
R8013
R8015
R8016
R8017

1-218-977-11
1-218-977-11
1-218-985-11
1-218-953-11
1-218-985-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

100K
100K
470K
1K
470K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8018
R8019
R8020
R8021
R8022

1-218-953-11
1-218-953-11
1-218-985-11
1-218-953-11
1-218-985-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
1K
470K
1K
470K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

Ref. No.

6-13

Part No.

Description

R8023
R8024
R8025
R8026
R8027

1-218-953-11
1-218-985-11
1-218-953-11
1-218-985-11
1-218-953-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
470K
1K
470K
1K

5%
5%
5%
5%
5%

Remark
1/16W
1/16W
1/16W
1/16W
1/16W

R8028
R8029
R8030
R8031
R8032

1-218-985-11
1-218-953-11
1-218-985-11
1-218-953-11
1-218-985-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

470K
1K
470K
1K
470K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8033
R8034
R8035
R8036
R8037

1-218-953-11
1-218-941-11
1-218-941-11
1-218-983-11
1-218-965-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
100
100
330K
10K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8038
R8039
R8040
R8041
R8042

1-218-953-11
1-218-977-11
1-218-985-11
1-218-985-11
1-208-955-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
METAL CHIP

1K
100K
470K
470K
680K

5%
5%
5%
5%
0.5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8043
R8044
R8045
R8046
R8047

1-208-955-11
1-218-990-11
1-218-983-11
1-218-961-11
1-218-953-11

METAL CHIP
SHORT
RES, CHIP
RES, CHIP
RES, CHIP

680K
0
330K
4.7K
1K

0.5%

1/16W

5%
5%
5%

1/16W
1/16W
1/16W

R8048
R8049
R8050
R8051
R8052

1-216-304-11
1-216-304-11
1-218-941-11
1-218-973-11
1-218-953-11

METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP

3.3
3.3
100
47K
1K

5%
5%
5%
5%
5%

1/10W
1/10W
1/16W
1/16W
1/16W

R8053
R8055
R8056
R8057
R8058

1-218-983-11
1-218-977-11
1-218-945-11
1-218-965-11
1-218-985-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

330K
100K
220
10K
470K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8061
R8062
R8063
R8064
R8065

1-218-989-11
1-218-983-11
1-218-990-11
1-218-990-11
1-218-990-11

RES, CHIP
RES, CHIP
SHORT
SHORT
SHORT

1M
330K
0
0
0

5%
5%

1/16W
1/16W

R8066
R8067
R8068
R8069
R8070

1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11

SHORT
SHORT
SHORT
SHORT
SHORT

0
0
0
0
0

R8071
R8072
R8073
R8074
R8075

1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11

SHORT
SHORT
SHORT
SHORT
SHORT

0
0
0
0
0

R8076
R8077
R8078
R8079
R8080

1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11

SHORT
SHORT
SHORT
SHORT
SHORT

0
0
0
0
0

R8081
R8082
R8083

1-218-990-11 SHORT
1-218-990-11 SHORT
1-218-977-11 RES, CHIP

5%

1/16W

0
0
100K

MAIN
Ref. No.

Part No.

Description

Remark

R8084
R8085

1-218-990-11 SHORT
1-218-983-11 RES, CHIP

0
330K

5%

1/16W

R8086
R8087
R8088
R8089
R8090

1-218-983-11
1-218-983-11
1-218-983-11
1-218-983-11
1-218-983-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

330K
330K
330K
330K
330K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8091
R8092
R8093
R8094
R8095

1-218-983-11
1-218-983-11
1-218-983-11
1-218-983-11
1-218-983-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

330K
330K
330K
330K
330K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8096
R8097
R8098
R8099
R8101

1-218-983-11
1-218-985-11
1-218-953-11
1-218-983-11
1-218-945-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
METAL CHIP

330K
470K
1K
330K
220

5%
5%
5%
5%
0.5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8102
R8103
R8104
R8105
R8106

1-208-671-11
1-208-679-11
1-208-683-11
1-208-691-11
1-208-683-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

330
680
1K
2.2K
1K

0.5%
0.5%
0.5%
0.5%
0.5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8107
R8108
R8109
R8110
R8111

1-218-945-11
1-218-945-11
1-218-990-11
1-218-990-11
1-218-977-11

METAL CHIP
METAL CHIP
SHORT
SHORT
RES, CHIP

220
220
0
0
100K

0.5%
0.5%

1/16W
1/16W

5%

1/16W

R8112
R8113
R8114
R8115
R8116

1-218-977-11
1-218-977-11
1-218-977-11
1-218-977-11
1-218-977-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

100K
100K
100K
100K
100K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8117
R8118
R8119
R8120
R8121

1-218-977-11
1-218-977-11
1-218-977-11
1-218-977-11
1-218-977-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

100K
100K
100K
100K
100K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8122
R8125
R8126
R8127
R8129

1-218-977-11
1-218-990-11
1-218-990-11
1-208-683-11
1-218-977-11

RES, CHIP
SHORT
SHORT
METAL CHIP
RES, CHIP

100K
0
0
1K
100K

5%

1/16W

0.5%
5%

1/16W
1/16W

R8130
R8208
R8501
R8502
R8503

1-218-977-11
1-208-679-11
1-218-961-11
1-218-961-11
1-218-961-11

RES, CHIP
METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP

100K
680
4.7K
4.7K
4.7K

5%
0.5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8504
R8505
R8506
R8507
R8508

1-218-961-11
1-218-961-11
1-218-961-11
1-218-961-11
1-218-965-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

4.7K
4.7K
4.7K
4.7K
10K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8509
R8510
R8511
R8512
R8513

1-218-965-11
1-218-965-11
1-218-965-11
1-218-977-11
1-218-977-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

10K
10K
10K
100K
100K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

Ref. No.

6-14

Part No.

Description

R8514
R8515
R8516
R8517
R8519

1-218-977-11
1-218-977-11
1-218-977-11
1-218-977-11
1-218-977-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

100K
100K
100K
100K
100K

5%
5%
5%
5%
5%

Remark
1/16W
1/16W
1/16W
1/16W
1/16W

R8520
R8521
R8522
R8523
R8524

1-218-949-11
1-218-977-11
1-218-985-11
1-218-985-11
1-218-989-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

470
100K
470K
470K
1M

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8525
R8526
R8527
R8528
R8529

1-218-989-11
1-218-977-11
1-218-985-11
1-218-985-11
1-218-961-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1M
100K
470K
470K
4.7K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8530
R8531
R8532
R8601
R8602

1-218-977-11
1-218-977-11
1-218-977-11
1-218-987-11
1-218-990-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
SHORT

100K
100K
100K
680K
0

5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W

R8603
R8901
R8902
R8903
R8904

1-218-990-11
1-218-977-11
1-218-977-11
1-218-977-11
1-218-990-11

SHORT
RES, CHIP
RES, CHIP
RES, CHIP
SHORT

0
100K
100K
100K
0

5%
5%
5%

1/16W
1/16W
1/16W

R8906
R8908
R8909
R8910
R8911

1-218-957-11
1-218-977-11
1-218-937-11
1-218-959-11
1-218-985-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

2.2K
100K
47
3.3K
470K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8912
R8913
R8914
R8915
R8916

1-218-965-11
1-218-965-11
1-218-989-11
1-216-304-11
1-218-949-11

RES, CHIP
RES, CHIP
RES, CHIP
METAL CHIP
RES, CHIP

10K
10K
1M
3.3
470

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/10W
1/16W

R8917
R8918
R8919
R8921
R8931

1-218-977-11
1-218-965-11
1-218-990-11
1-218-990-11
1-218-967-11

RES, CHIP
RES, CHIP
SHORT
SHORT
RES, CHIP

100K
10K
0
0
15K

5%
5%

1/16W
1/16W

5%

1/16W

R8932
R8933
R8934
R8935
R8936

1-218-965-11
1-218-989-11
1-218-965-11
1-218-977-11
1-218-959-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

10K
1M
10K
100K
3.3K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R8937
R9101
R9102
R9103
R9104

1-218-989-11
1-208-947-11
1-208-927-11
1-208-691-11
1-218-969-11

RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP

1M
330K
47K
2.2K
22K

5%
0.5%
0.5%
0.5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R9105
R9106
R9107
R9108
R9109

1-218-977-11
1-218-989-11
1-218-989-11
1-218-979-11
1-218-990-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
SHORT

100K
1M
1M
150K
0

5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W

R9110
R9111
R9112

1-218-989-11 RES, CHIP
1-218-981-11 RES, CHIP
1-218-977-11 RES, CHIP

1M
220K
100K

5%
5%
5%

1/16W
1/16W
1/16W

MAIN
Ref. No.

Part No.

Description

Ref. No.

Remark

R9113
R9114

1-218-989-11 RES, CHIP
1-218-989-11 RES, CHIP

1M
1M

5%
5%

1/16W
1/16W

R9116
R9117
R9118
R9119
R9120

1-218-973-11
1-218-990-11
1-208-947-11
1-208-947-11
1-218-989-11

RES, CHIP
SHORT
METAL CHIP
METAL CHIP
RES, CHIP

47K
0
330K
330K
1M

5%

1/16W

0.5%
0.5%
5%

1/16W
1/16W
1/16W

R9121
R9123
R9124
R9125
R9126

1-218-990-11
1-218-977-11
1-218-989-11
1-218-989-11
1-218-977-11

SHORT
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

0
100K
1M
1M
100K

R9127
R9128
R9129
R9130
R9132

1-218-977-11
1-218-989-11
1-218-989-11
1-218-990-11
1-218-989-11

RES, CHIP
RES, CHIP
RES, CHIP
SHORT
RES, CHIP

R9134
R9135
R9136
R9137
R9139

1-218-989-11
1-218-989-11
1-218-989-11
1-218-979-11
1-218-989-11

R9140
R9143
R9144
R9147
R9148

5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W

100K
1M
1M
0
1M

5%
5%
5%

1/16W
1/16W
1/16W

5%

1/16W

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1M
1M
1M
150K
1M

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

1-208-715-11
1-218-990-11
1-208-711-11
1-218-989-11
1-218-990-11

METAL CHIP
SHORT
METAL CHIP
RES, CHIP
SHORT

22K
0
15K
1M
0

0.5%

1/16W

0.5%
5%

1/16W
1/16W

R9150
R9152
R9153
R9154
R9155

1-218-990-11
1-208-691-11
1-218-989-11
1-218-989-11
1-208-715-11

SHORT
METAL CHIP
RES, CHIP
RES, CHIP
METAL CHIP

0
2.2K
1M
1M
22K

0.5%
5%
5%
0.5%

1/16W
1/16W
1/16W
1/16W

R9156
R9157
R9159
R9161
R9901

1-208-927-11
1-218-959-11
1-208-927-11
1-218-989-11
1-218-990-11

METAL CHIP
RES, CHIP
METAL CHIP
RES, CHIP
SHORT

47K
3.3K
47K
1M
0

0.5%
5%
0.5%
5%

1/16W
1/16W
1/16W
1/16W

R9902
R9903
R9904
R9905
R9906

1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11

SHORT
SHORT
SHORT
SHORT
SHORT

0
0
0
0
0

R9910

1-218-990-11 SHORT

0

X5403
X8001
X8002

Part No.

POWER

Description

Remark

1-781-247-21 VIBRATOR, CRYSTAL (70.54MHz)
1-767-994-41 VIBRATOR, CRYSTAL (32.768kHz)
1-767-994-22 VIBRATOR, CRYSTAL (32.768kHz)

X8003 1-781-259-21 VIBRATOR, CRYSTAL (9.8304MHz)
X8501 1-781-260-21 VIBRATOR, CRYSTAL (6.6MHz)
************************************************************
A-3321-881-A POWER BOARD, COMPLETE
***********************
(Ref. No.: 20,000 Series)
3-043-103-01 CUSHION (SHIELD)
4-216-027-01 CASE (FRONT), SHIELD
4-216-028-01 CASE (REAR), SHIELD

*
*

< CAPACITOR >
C9001
C9002
C9003
C9004
C9005

1-164-937-11
1-164-937-11
1-164-937-11
1-119-751-11
1-119-751-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP

0.001uF
0.001uF
0.001uF
22uF
22uF

10%
10%
10%
20%
20%

16V
16V
16V
16V
16V

C9007
C9008
C9009
C9010
C9011

1-119-923-81
1-107-820-11
1-107-820-11
1-107-820-11
1-119-751-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP

0.047uF
0.1uF
0.1uF
0.1uF
22uF

10%
0%
0%
0%
20%

10V
16V
16V
16V
16V

C9012
C9013
C9014
C9015
C9017

1-164-938-11
1-164-874-11
1-164-489-11
1-119-751-11
1-164-942-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

0.0015uF
100PF
0.22uF
22uF
0.0068uF

10%
5%
10%
20%
10%

16V
16V
16V
16V
16V

C9018
C9019
C9021
C9023
C9024

1-119-751-11
1-164-941-11
1-164-938-11
1-164-939-11
1-164-938-11

TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

22uF
0.0047uF
0.0015uF
0.0022uF
0.0015uF

20%
10%
10%
10%
10%

16V
16V
16V
16V
16V

C9027
C9028
C9029
C9030
C9031

1-164-858-11
1-164-858-11
1-119-751-11
1-164-935-11
1-164-935-11

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP

22PF
22PF
22uF
470PF
470PF

5%
5%
20%
10%
10%

16V
16V
16V
16V
16V

C9032
C9033
C9034
C9035
C9036

1-164-858-11
1-164-935-11
1-164-858-11
1-164-935-11
1-164-935-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

22PF
470PF
22PF
470PF
470PF

5%
10%
5%
10%
10%

16V
16V
16V
16V
16V

C9037
C9038
C9039
C9040
C9041

1-164-935-11
1-164-858-11
1-164-858-11
1-119-751-11
1-119-751-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP

470PF
22PF
22PF
22uF
22uF

10%
5%
5%
20%
20%

16V
16V
16V
16V
16V

C9042
C9043
C9044
C9045
C9046

1-115-566-11
1-115-566-11
1-115-566-11
1-115-566-11
1-115-566-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

4.7uF
4.7uF
4.7uF
4.7uF
4.7uF

10%
10%
10%
10%
10%

10V
10V
10V
10V
10V

C9047
C9048
C9049

1-115-566-11 CERAMIC CHIP 4.7uF
1-104-851-11 TANTALUM CHIP 10uF
1-104-851-11 TANTALUM CHIP 10uF

10%
20%
20%

10V
10V
10V

< SWITCH >
S8001
S8002
S8003

1-572-467-61 SWITCH, PUSH (1 KEY)
(OPEN/CLOSE DETECT)
1-572-467-61 SWITCH, PUSH (1 KEY) (HALF LOCK DETECT)
1-762-805-21 SWITCH, PUSH (1 KEY)
(OPEN CLOSE DETECT)
< BATTERY >

U8001

1-528-834-11 BATTERY, LITHIUM SECONDARY
< VIBRATOR >

X5301
X5401

1-767-498-11 OSCILLATOR, CRYSTAL (22.5792MHz)
1-767-124-11 VIBRATOR, CRYSTAL (16.9344MHz)

6-15

POWER
Ref. No.

Part No.

Description

Remark

C9050
C9051

1-104-851-11 TANTALUM CHIP 10uF
1-104-852-11 TANTALUM CHIP 22uF

20%
20%

10V
10V

C9052
C9053
C9055
C9057
C9059

1-164-937-11
1-115-339-11
1-104-913-11
1-110-569-11
1-115-339-11

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP

0.001uF
0.1uF
10uF
47uF
0.1uF

10%
10%
20%
20%
10%

16V
50V
16V
6.3V
50V

C9061
C9062
C9063
C9064
C9065

1-104-852-11
1-115-566-11
1-104-852-11
1-104-916-11
1-104-852-11

TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP

22uF
4.7uF
22uF
6.8uF
22uF

20%
10%
20%
20%
20%

10V
10V
10V
20V
10V

C9066
C9067
C9068
C9069
C9070

1-107-820-11
1-107-820-11
1-104-916-11
1-107-820-11
1-113-994-11

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP

0.1uF
0.1uF
6.8uF
0.1uF
6.8uF

0%
0%
20%
0%
20%

16V
16V
20V
16V
16V

C9071
C9072
C9073
C9074
C9076

1-113-994-11
1-113-984-11
1-104-752-11
1-104-916-11
1-113-682-11

TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP

6.8uF
1.5uF
33uF
6.8uF
33uF

20%
20%
20%
20%
20%

16V
35V
6.3V
20V
10V

C9077
C9078
C9079
C9080
C9081

1-115-566-11
1-115-566-11
1-115-566-11
1-115-566-11
1-115-566-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

4.7uF
4.7uF
4.7uF
4.7uF
4.7uF

10%
10%
10%
10%
10%

10V
10V
10V
10V
10V

Ref. No.

Part No.

Description

Remark

< IC >
IC9001
IC9002

8-759-596-54 IC SN104241PM-TEB
8-759-252-41 IC TK11900MTL
< COIL >

L9001
L9002
L9003
L9004
L9005

1-409-529-41
1-409-529-41
1-409-529-41
1-414-757-11
1-409-529-41

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

10uH
10uH
10uH
100uH
10uH

L9006
L9007
L9008
L9009
L9010

1-424-674-11
1-409-535-41
1-409-535-41
1-409-529-41
1-409-529-41

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

22uH
100uH
100uH
10uH
10uH

L9013
L9015
L9016
L9017
L9018

1-469-367-21
1-414-757-11
1-414-757-11
1-469-367-21
1-469-367-21

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

10uH
100uH
100uH
10uH
10uH

L9019
L9020
L9021
L9022
L9023

1-469-367-21
1-414-757-11
1-414-757-11
1-414-757-11
1-469-367-21

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

10uH
100uH
100uH
100uH
10uH

< TRANSISTOR >

< CONNECTOR >
CN9001 1-785-482-41 CONNECTOR, BOARD TO BOARD 70P
* CN9002 1-695-106-11 PIN, CONNECTOR (PC BOARD) 4P

Q9001
Q9002
Q9003
Q9004
Q9005

8-729-804-41
8-729-037-52
8-729-043-94
8-729-043-94
8-729-043-94

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

2SB1122-S
2SD2216J-QR (TX).SO
CPH3106-PM-TL
CPH3106-PM-TL
CPH3106-PM-TL

Q9006
Q9007
Q9008
Q9009
Q9010

8-729-043-94
8-729-047-38
8-729-047-38
8-729-043-94
8-729-427-70

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

CPH3106-PM-TL
FDN359AN
FDN359AN
CPH3106-PM-TL
XP4401

< DIODE >
D9001
D9002
D9003
D9004
D9005

8-719-074-63
8-719-074-63
8-719-074-63
8-719-074-63
8-719-074-63

DIODE
DIODE
DIODE
DIODE
DIODE

MAZS120001SO
MAZS120001SO
MAZS120001SO
MAZS120001SO
MAZS120001SO

D9006
D9007
D9008
D9009
D9010

8-719-067-36
8-719-067-36
8-719-067-36
8-719-067-36
8-719-067-36

DIODE
DIODE
DIODE
DIODE
DIODE

MA3ZD1200LS0
MA3ZD1200LS0
MA3ZD1200LS0
MA3ZD1200LS0
MA3ZD1200LS0

D9011
D9012
D9013
D9014
D9015

8-719-074-63
8-719-056-48
8-719-056-48
8-719-056-48
8-719-056-48

DIODE
DIODE
DIODE
DIODE
DIODE

MAZS120001SO
1SS388 (TPL3)
1SS388 (TPL3)
1SS388 (TPL3)
1SS388 (TPL3)

< RESISTOR >
R9001
R9003
R9004
R9005
R9006

1-208-699-11
1-208-707-11
1-218-973-11
1-218-969-11
1-218-973-11

METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP

4.7K
10K
47K
22K
47K

0.5%
0.5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R9007
R9008
R9011
R9013
R9014

1-208-699-11
1-218-967-11
1-218-965-11
1-218-965-11
1-218-959-11

METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

4.7K
15K
10K
10K
3.3K

0.5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R9015
R9016
R9017
R9019
R9020

1-218-965-11
1-208-715-11
1-208-715-11
1-208-927-11
1-218-969-11

RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP

10K
22K
22K
47K
22K

5%
0.5%
0.5%
0.5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R9021
R9022
R9023
R9024

1-208-715-11
1-208-703-11
1-208-715-11
1-208-715-11

METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

22K
6.8K
22K
22K

0.5%
0.5%
0.5%
0.5%

1/16W
1/16W
1/16W
1/16W

< FUSE >
0 F9001
0 F9002
0 F9003
0 F9004

1-533-760-21
1-533-760-21
1-533-760-21
1-533-760-21

FUSE (SMD) (1.4A/24V)
FUSE (SMD) (1.4A/24V)
FUSE (SMD) (1.4A/24V)
FUSE (SMD) (1.4A/24V)
< FERRITE BEAD >

* FB9001 1-469-230-21 FERRITE
* FB9002 1-469-230-21 FERRITE

0uH
0uH

6-16

The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.

Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.

POWER
Ref. No.

Part No.

Description

Ref. No.

Remark

R9025

1-208-691-11 METAL CHIP

2.2K

0.5%

1/16W

R9029
R9031
R9032
R9033
R9035

1-208-703-11
1-218-965-11
1-218-965-11
1-208-707-11
1-208-703-11

METAL CHIP
RES, CHIP
RES, CHIP
METAL CHIP
METAL CHIP

6.8K
10K
10K
10K
6.8K

0.5%
5%
5%
0.5%
0.5%

1/16W
1/16W
1/16W
1/16W
1/16W

R9036
R9037
R9038
R9039
R9040

1-208-703-11
1-218-849-11
1-218-959-11
1-218-849-11
1-218-849-11

METAL CHIP
METAL CHIP
RES, CHIP
METAL CHIP
METAL CHIP

6.8K
3.3K
3.3K
3.3K
3.3K

0.5%
0.5%
5%
0.5%
0.5%

1/16W
1/16W
1/16W
1/16W
1/16W

R9041
R9042
R9043
R9044
R9045

1-208-683-11
1-218-975-11
1-218-971-11
1-218-971-11
1-218-965-11

METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
68K
33K
33K
10K

0.5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R9046
R9047
R9048
R9049
R9050

1-218-955-11
1-208-935-11
1-208-927-11
1-208-711-11
1-208-699-11

RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

1.5K
100K
47K
15K
4.7K

5%
0.5%
0.5%
0.5%
0.5%

1/16W
1/16W
1/16W
1/16W
1/16W

R9051
R9052
R9053
R9054
R9055

1-218-969-11
1-208-943-11
1-208-935-11
1-208-715-11
1-208-931-11

RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP

22K
220K
100K
22K
68K

5%
0.5%
0.5%
0.5%
0.5%

1/16W
1/16W
1/16W
1/16W
1/16W

R9056
R9058
R9059
R9060
R9062

1-218-977-11
1-208-935-11
1-208-715-11
1-218-933-11
1-218-933-11

RES, CHIP
METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP

100K
100K
22K
22
22

5%
0.5%
0.5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R9064
R9066
R9067
R9068

1-218-933-11
1-219-365-11
1-216-296-91
1-211-950-11

RES, CHIP
SHORT
SHORT
SHORT

22
0
0
0

5%

1/16W

D5901
D5902

Q5901
Q5902
Q5903

8-759-475-53 IC TC74LCX541FT (EL)

8-729-037-73 TRANSISTOR
8-729-047-35 TRANSISTOR
8-729-047-82 TRANSISTOR

UN9212J- (TX).SO
FTD1003-TL
FTD2007-TL

R5901 1-218-983-11 RES, CHIP
330K
5%
1/16W
R5902 1-218-983-11 RES, CHIP
330K
5%
1/16W
R5903 1-218-983-11 RES, CHIP
330K
5%
1/16W
R5904 1-218-983-11 RES, CHIP
330K
5%
1/16W
R5905 1-218-983-11 RES, CHIP
330K
5%
1/16W
************************************************************
VC-216 BOARD, COMPLETE
***********************
(Ref. No.: 20,000 Series)
< CAPACITOR >

< CAPACITOR >

1-107-820-11 CERAMIC CHIP

8-719-073-16 DIODE SBE802-TL
8-719-073-16 DIODE SBE802-TL

< RESISTOR >

A-3321-863-A REC BOARD, COMPLETE
*********************
(Ref. No.: 20,000 Series)

C5906

Remark

< TRANSISTOR >

0 T9001 1-433-623-21 TRANSFORMER, CONVERTER
************************************************************

CERAMIC CHIP
CAP-CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP

Description

< IC >

< TRANSFORMER >

1-107-820-11
1-117-177-91
1-104-851-11
1-104-851-11
1-104-851-11

VC-216

< DIODE >

IC5901

C5901
C5902
C5903
C5904
C5905

Part No.

REC

C001
C002
C003
C004
C007

1-104-851-11
1-164-943-11
1-164-943-11
1-164-850-11
1-107-826-91

TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

10uF
0.01uF
0.01uF
10PF
0.1uF

20%
10%
10%
0.5PF
10%

10V
16V
16V
16V
16V

C008
C009
C010
C011
C012

1-119-750-11
1-113-994-11
1-107-826-91
1-119-750-11
1-107-826-91

TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

22uF
6.8uF
0.1uF
22uF
0.1uF

20%
20%
10%
20%
10%

6.3V
16V
16V
6.3V
16V

C013
C014
C015
C016
C017

1-165-176-11
1-165-176-11
1-107-826-91
1-165-176-11
1-165-176-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.047uF
0.047uF
0.1uF
0.047uF
0.047uF

10%
10%
10%
10%
10%

16V
16V
16V
16V
16V

C018
C019
C020
C021
C022

1-125-817-11
1-125-817-11
1-125-817-11
1-125-817-11
1-110-501-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

10uF
10uF
10uF
10uF
0.33uF

10%
10%
10%
10%
10%

6.3V
6.3V
6.3V
6.3V
16V

0.1uF
33PF
10uF
10uF
10uF

0%
5%
20%
20%
20%

16V
500V
10V
10V
10V

C023
C024
C101
C102
C103

1-107-826-91
1-119-750-11
1-164-506-11
1-164-506-11
1-164-862-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
22uF
4.7uF
4.7uF
33PF

10%
20%
0%
0%
5%

16V
6.3V
16V
16V
16V

0.1uF

0%

16V

C104
C105
C106
C107
C108

1-109-982-11
1-164-862-11
1-107-826-91
1-119-750-11
1-125-839-91

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP

1uF
33PF
0.1uF
22uF
47uF

10%
5%
10%
20%
20%

10V
16V
16V
6.3V
6.3V

C109
C110
C111

1-107-826-91 CERAMIC CHIP
1-107-826-91 CERAMIC CHIP
1-107-826-91 CERAMIC CHIP

0.1uF
0.1uF
0.1uF

10%
10%
10%

16V
16V
16V

< CONNECTOR >
CN5901 1-778-711-11 CONNECTOR, FFC/FPC (ZIF) 5P
* CN5902 1-778-158-21 CONNECTOR, FFC/FPC (ZIF) 10P

6-17

The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.

Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.

VC-216
Ref. No.

Part No.

Description

Remark

C112
C113

1-107-826-91 CERAMIC CHIP
1-107-826-91 CERAMIC CHIP

0.1uF
0.1uF

10%
10%

16V
16V

C114
C115
C116
C117
C118

1-164-943-11
1-165-176-11
1-165-176-11
1-164-943-11
1-107-826-91

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.01uF
0.047uF
0.047uF
0.01uF
0.1uF

10%
10%
10%
10%
10%

16V
16V
16V
16V
16V

C119
C120
C121
C123
C124

1-164-846-11
1-107-826-91
1-164-943-11
1-107-826-91
1-107-826-91

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

6PF
0.1uF
0.01uF
0.1uF
0.1uF

0.5PF
10%
10%
10%
10%

16V
16V
16V
16V
16V

C125
C126
C127
C128
C129

1-125-837-91
1-107-826-91
1-107-826-91
1-117-919-11
1-119-750-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP

1uF
0.1uF
0.1uF
10uF
22uF

10%
10%
10%
20%
20%

6.3V
16V
16V
6.3V
6.3V

C130
C131
C132
C133
C134

1-107-826-91
1-107-826-91
1-125-837-91
1-165-176-11
1-117-920-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP

0.1uF
0.1uF
1uF
0.047uF
10uF

10%
10%
10%
10%
20%

16V
16V
6.3V
16V
6.3V

C135
C136
C137
C138
C139

1-107-826-91
1-164-943-11
1-117-920-11
1-107-826-91
1-164-943-11

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP

0.1uF
0.01uF
10uF
0.1uF
0.01uF

10%
10%
20%
10%
10%

16V
16V
6.3V
16V
16V

C140
C141
C142
C143
C201

1-164-943-11
1-107-826-91
1-109-982-11
1-164-850-11
1-164-943-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.01uF
0.1uF
1uF
10PF
0.01uF

10%
10%
10%
0.5PF
10%

16V
16V
10V
16V
16V

C202
C203
C204
C205
C206

1-164-941-11
1-107-826-91
1-107-826-91
1-164-935-11
1-164-489-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.0047uF
0.1uF
0.1uF
470PF
0.22uF

10%
10%
10%
10%
10%

16V
16V
16V
16V
16V

C207
C208
C209
C210
C211

1-164-937-11
1-107-823-11
1-164-943-11
1-164-943-11
1-164-943-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.001uF
0.47uF
0.01uF
0.01uF
0.01uF

10%
10%
10%
10%
10%

16V
16V
16V
16V
16V

C212
C213
C214
C215
C216

1-164-939-11
1-164-943-11
1-107-826-91
1-117-920-11
1-164-943-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

0.0022uF
0.01uF
0.1uF
10uF
0.01uF

10%
10%
10%
20%
10%

16V
16V
16V
6.3V
16V

C217
C218
C219
C220
C221

1-107-826-91
1-107-826-91
1-119-750-11
1-164-943-11
1-125-839-91

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP

0.1uF
0.1uF
22uF
0.01uF
47uF

10%
10%
20%
10%
20%

16V
16V
6.3V
16V
6.3V

C222

1-119-750-11 TANTALUM CHIP 22uF

20%

6.3V

Ref. No.

Description

Remark

< DIODE >
D101
D201

8-713-103-84 DIODE 1T379-01-T8A
8-719-056-23 DIODE MA2S111- (K8).SO
< FERRITE BEAD >

FB101
FB102
FB103
FB104
FB105

1-414-228-11
1-500-284-21
1-414-228-11
1-414-228-11
1-414-228-11

FERRITE
FERRITE
FERRITE
FERRITE
FERRITE

0uH
0uH
0uH
0uH
0uH

FB201

1-414-228-11 FERRITE

0uH

< IC >
IC002
IC101
IC102
IC103
IC104

8-759-489-19
8-752-386-72
8-759-570-81
8-759-445-93
8-759-387-31

IC
IC
IC
IC
IC

uPC6756GR-8JG-E2
CXD2444R
AD9808AJSTRL
AK6440AM-E2
TC75S55F (TE85R)

IC105
IC106
IC201
IC202

8-759-497-43
8-752-904-85
8-759-444-87
8-759-492-31

IC
IC
IC
IC

CXD8691R-TEB
CXP912032-098R-T6
NJM324V (TE2)
MPC17A134VMEL

< COIL >
L001
L002
L101
L103
L104

1-414-757-11
1-414-754-11
1-414-754-11
1-414-754-11
1-414-754-11

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

L201
L202
L203

1-414-754-11 INDUCTOR
1-414-754-11 INDUCTOR
1-414-754-11 INDUCTOR

100uH
10uH
10uH
10uH
10uH
10uH
10uH
10uH

< TRANSISTOR >
Q001
Q101
Q102
Q103
Q104

8-729-117-73
8-729-037-61
8-729-037-74
8-729-037-61
8-729-037-74

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

2SC4178-F14
UN9113J- (TX).SO
UN9213J- (TX).SO
UN9113J- (TX).SO
UN9213J- (TX).SO

Q201
Q202
Q203
Q204

8-729-037-53
8-729-037-52
8-729-037-53
8-729-037-52

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

2SB1462J-QR (TX).SO
2SD2216J-QR (TX).SO
2SB1462J-QR (TX).SO
2SD2216J-QR (TX).SO

< RESISTOR/FILTER>

< CONNECTOR >
CN101
CN201

Part No.

1-778-804-11 CONNECTOR, BOARD TO BOARD 40P
1-766-354-21 CONNECTOR, FFC/FPC 24P

6-18

R005
R007
R008
R009
R010

1-218-959-11
1-218-969-11
1-218-933-11
1-218-969-11
1-218-969-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

3.3K
22K
22
22K
22K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R011
R012
R013
R014
R015

1-218-969-11
1-218-965-11
1-218-965-11
1-218-989-11
1-218-967-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

22K
10K
10K
1M
15K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R016
R101

1-218-989-11 RES, CHIP
1-469-537-21 FILTER

1M
0uH

5%

1/16W

VC-216
Ref. No.

Part No.

Description

Remark

R102
R103
R104

1-469-537-21 FILTER
1-218-933-11 RES, CHIP
1-218-977-11 RES, CHIP

0uH
22
100K

R105
R106
R107
R108
R109

1-218-945-11
1-218-977-11
1-218-990-11
1-218-985-11
1-218-983-11

RES, CHIP
RES, CHIP
SHORT
RES, CHIP
RES, CHIP

R110
R111
R112
R113
R115

1-218-953-11
1-218-973-11
1-218-973-11
1-218-953-11
1-218-977-11

R116
R117
R118
R119
R120

Ref. No.
R224
R225
R226

Part No.

Description

1-218-973-11 RES, CHIP
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP

VF
Remark

47K
0
0

5%
5%
5%

1/16W
1/16W
1/16W

5%
5%

1/16W
1/16W

220
100K
0
470K
330K

5%
5%

1/16W
1/16W

5%
5%

1/16W
1/16W

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
47K
47K
1K
100K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

1-218-977-11
1-216-864-11
1-218-941-11
1-218-941-11
1-218-977-11

RES, CHIP
METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP

100K
0
100
100
100K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R121
R122
R123
R124
R125

1-218-977-11
1-218-977-11
1-218-933-11
1-218-953-11
1-218-973-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

100K
100K
22
1K
47K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

C4501
C4502
C4503
C4504
C4505

1-125-777-11
1-164-943-11
1-104-851-11
1-104-851-11
1-164-943-11

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP

0.1uF
0.01uF
10uF
10uF
0.01uF

10%
10%
20%
20%
10%

6.3V
16V
10V
10V
16V

R126
R127
R128
R129
R130

1-218-989-11
1-218-973-11
1-218-953-11
1-218-989-11
1-218-989-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1M
47K
1K
1M
1M

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

C4506
C4507
C4508
C4509
C4510

1-119-750-11
1-117-919-11
1-135-179-21
1-125-777-11
1-107-686-11

TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP

22uF
10uF
2.2uF
0.1uF
4.7uF

20%
20%
20%
10%
20%

6.3V
6.3V
16V
10V
16V

R131
R132
R133
R134
R135

1-218-977-11
1-218-961-11
1-218-961-11
1-218-957-11
1-218-965-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

100K
4.7K
4.7K
2.2K
10K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

C4512
C4514
C4515
C4516
C4517

1-119-750-11
1-125-777-11
1-125-777-11
1-107-686-11
1-107-686-11

TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP

22uF
0.1uF
0.1uF
4.7uF
4.7uF

20%
10%
10%
20%
20%

6.3V
10V
10V
16V
16V

R136
R137
R138
R201
R202

1-216-864-11
1-216-864-11
1-216-009-91
1-218-961-11
1-218-975-11

METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP

0
0
22
4.7K
68K

5%
5%
5%
5%
5%

1/16W
1/16W
1/10W
1/16W
1/16W

C4518
C4519
C4520
C4521
C4522

1-107-686-11
1-115-566-11
1-119-750-11
1-135-179-21
1-164-943-11

TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP

4.7uF
4.7uF
22uF
2.2uF
0.01uF

20%
10%
20%
20%
10%

16V
10V
6.3V
16V
16V

R203
R205
R206
R207
R208

1-216-864-11
1-218-975-11
1-218-989-11
1-218-961-11
1-218-957-11

METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

0
68K
1M
4.7K
2.2K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

C4523
C4524
C4525
C4526
C4527

1-125-777-11
1-164-505-11
1-125-777-11
1-107-686-11
1-164-943-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP

0.1uF
2.2uF
0.1uF
4.7uF
0.01uF

10%
0%
10%
20%
10%

10V
16V
10V
16V
16V

R209
R210
R211
R212
R213

1-218-953-11
1-218-981-11
1-218-965-11
1-218-985-11
1-218-985-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
220K
10K
470K
470K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

C4601
C4602
C4603
C4604
C4605

1-115-467-11
1-164-943-11
1-104-851-11
1-107-826-91
1-104-916-11

CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP

0.22uF
0.01uF
10uF
0.1uF
6.8uF

10%
10%
20%
10%
20%

10V
16V
10V
16V
20V

R214
R215
R216
R217
R218

1-218-957-11
1-218-969-11
1-218-963-11
1-218-985-11
1-218-953-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

2.2K
22K
6.8K
470K
1K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

C4606
C4608
C4610
C4611
C4612

1-164-939-11
1-107-686-11
1-107-819-11
1-107-819-11
1-109-982-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.0022uF
4.7uF
0.022uF
0.022uF
1uF

10%
20%
10%
10%
10%

16V
16V
16V
16V
10V

R219
R220
R221
R222
R223

1-218-953-11
1-218-947-11
1-218-969-11
1-218-953-11
1-218-965-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

1K
330
22K
1K
10K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

C4613
C4614
C4615
C4616
C4617

1-164-943-11
1-164-878-11
1-164-943-11
1-164-940-11
1-115-566-11

CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

0.01uF
150PF
0.01uF
0.0033uF
4.7uF

10%
5%
10%
10%
10%

16V
16V
16V
16V
10V

< SENSOR >
SE001
SE201

1-803-042-41 SENSOR, ANGULAR VELOCITY (YAW SENSOR)
1-803-042-31 SENSOR, ANGULAR VELOCITY
(PITCH SENSOR)
< VIBRATOR >

X101
1-767-203-21 VIBRATOR, CRYSTAL (36MHz)
X102
1-767-980-21 VIBRATOR, CERAMIC (20MHz)
************************************************************
A-3321-879-A VF BOARD, COMPLETE
*******************
(Ref. No.: 20,000 Series)
< CAPACITOR >

6-19

VF
Ref. No.

Part No.

Description

C4618
C4619
C4620
C4621
C4622

1-164-943-11
1-135-259-11
1-164-874-11
1-162-964-11
1-164-943-11

CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP

C4624
C4625

1-107-820-11 CERAMIC CHIP
1-165-112-11 CERAMIC CHIP

Remark
0.01uF
10uF
100PF
0.001uF
0.01uF

10%
20%
5%
10%
10%

16V
6.3V
16V
50V
16V

0.1uF
0.33uF

0%
0%

16V
16V

Ref. No.

< CONNECTOR >
CN4501 1-784-420-11 CONNECTOR, FFC/FPC (ZIF) 21P
CN4601 1-778-596-21 CONNECTOR, BOARD TO BOARD 30P
CN4901 1-764-704-21 CONNECTOR, FFC/FPC (LIF) 5P
< DIODE >
D4601
D4602

8-719-043-70 DIODE MA6S121- (TX)
8-713-102-80 DIODE 1T369-01-T8A
< IC >

IC4501
IC4502
IC4601
IC4602

8-759-546-65
8-759-596-12
8-759-097-75
8-752-392-33

IC
IC
IC
IC

CXA8115AR-T4
AK9813AFS-E2
MB3789PFV-G-BND
CXD2458AR

< COIL >
L4501
L4502
L4503
L4601
L4602

1-414-754-11
1-414-754-11
1-414-754-11
1-414-406-41
1-414-756-11

INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR

10uH
10uH
10uH
220uH
47uH

L4603

1-412-949-21 INDUCTOR

6.8uH

< TRANSISTOR >
Q4502
Q4503
Q4504
Q4505
Q4506

8-729-037-53
8-729-037-53
8-729-037-53
8-729-037-53
8-729-037-53

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

2SB1462J-QR (TX).SO
2SB1462J-QR (TX).SO
2SB1462J-QR (TX).SO
2SB1462J-QR (TX).SO
2SB1462J-QR (TX).SO

Q4507
Q4601
Q4602
Q4603

8-729-037-53
8-729-013-73
8-729-037-61
8-729-037-74

TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR

2SB1462J-QR (TX).SO
RN2105-TE85R
UN9113J- (TX).SO
UN9213J- (TX).SO

< RESISTOR >
R4501
R4502
R4503
R4507
R4508

1-216-009-91
1-218-969-11
1-218-990-11
1-218-969-11
1-218-975-11

RES, CHIP
RES, CHIP
SHORT
RES, CHIP
RES, CHIP

22
22K
0
22K
68K

5%
5%

1/10W
1/16W

5%
5%

1/16W
1/16W

R4514
R4515
R4516
R4517
R4518

1-208-711-11
1-208-691-11
1-218-990-11
1-218-990-11
1-218-990-11

METAL CHIP
METAL CHIP
SHORT
SHORT
SHORT

15K
2.2K
0
0
0

0.5%
0.5%

1/16W
1/16W

R4519
R4520
R4523
R4524

1-208-675-11
1-208-683-11
1-218-971-11
1-218-975-11

METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP

470
1K
33K
68K

0.5%
0.5%
5%
5%

1/16W
1/16W
1/16W
1/16W

6-20

Part No.

Description

Remark

R4525

1-218-975-11 RES, CHIP

68K

5%

1/16W

R4526
R4527
R4528
R4529
R4530

1-218-971-11
1-218-985-11
1-218-971-11
1-218-957-11
1-218-971-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

33K
470K
33K
2.2K
33K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4531
R4532
R4533
R4534
R4535

1-218-975-11
1-218-971-11
1-218-849-11
1-208-675-11
1-208-683-11

RES, CHIP
RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP

68K
33K
3.3K
470
1K

5%
5%
0.5%
0.5%
0.5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4538
R4539
R4540
R4541
R4542

1-218-971-11
1-218-975-11
1-218-990-11
1-218-941-11
1-218-941-11

RES, CHIP
RES, CHIP
SHORT
RES, CHIP
RES, CHIP

33K
68K
0
100
100

5%
5%

1/16W
1/16W

5%
5%

1/16W
1/16W

R4543
R4544
R4546
R4547
R4550

1-218-941-11
1-218-957-11
1-218-903-11
1-218-887-11
1-218-990-11

RES, CHIP
RES, CHIP
METAL CHIP
METAL CHIP
SHORT

100
2.2K
220K
47K
0

5%
5%
0.5%
0.5%

1/16W
1/16W
1/16W
1/16W

R4551
R4553
R4556
R4557
R4558

1-218-990-11
1-208-691-11
1-218-969-11
1-208-675-11
1-208-683-11

SHORT
METAL CHIP
RES, CHIP
METAL CHIP
METAL CHIP

0
2.2K
22K
470
1K

0.5%
5%
0.5%
0.5%

1/16W
1/16W
1/16W
1/16W

R4559
R4560
R4561
R4562
R4564

1-218-971-11
1-218-975-11
1-218-957-11
1-218-875-11
1-218-990-11

RES, CHIP
RES, CHIP
RES, CHIP
METAL CHIP
SHORT

33K
68K
2.2K
15K
0

5%
5%
5%
0.5%

1/16W
1/16W
1/16W
1/16W

R4565
R4566
R4567
R4568
R4570

1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-208-707-11

SHORT
SHORT
SHORT
SHORT
METAL CHIP

0
0
0
0
10K

0.5%

1/16W

R4601
R4602
R4603
R4604
R4605

1-217-671-11
1-217-671-11
1-208-719-11
1-218-971-11
1-208-939-11

METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP
METAL CHIP

1
1
33K
33K
150K

5%
5%
0.5%
5%
0.5%

1/10W
1/10W
1/16W
1/16W
1/16W

R4607
R4608
R4609
R4610
R4611

1-208-927-11
1-218-975-11
1-218-981-11
1-218-973-11
1-218-965-11

METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

47K
68K
220K
47K
10K

0.5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4612
R4613
R4614
R4615
R4616

1-218-973-11
1-218-973-11
1-218-965-11
1-218-969-11
1-218-969-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

47K
47K
10K
22K
22K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4617
R4618
R4619
R4620
R4621

1-218-985-11
1-218-953-11
1-218-971-11
1-218-979-11
1-218-979-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

470K
1K
33K
150K
150K

5%
5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W
1/16W

R4622

1-218-961-11 RES, CHIP

4.7K

5%

1/16W

VF
Ref. No.
R4623
R4624
R4626
R4627

Part No.

Description

1-218-983-11
1-218-971-11
1-218-969-11
1-218-965-11

RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP

Remark
330K
33K
22K
10K

5%
5%
5%
5%

1/16W
1/16W
1/16W
1/16W

R4628 1-218-971-11 RES, CHIP
33K
5%
1/16W
R4629 1-218-990-11 SHORT
0
R4630 1-218-953-11 RES, CHIP
1K
5%
1/16W
R4634 1-218-990-11 SHORT
0
R4636 1-218-963-11 RES, CHIP
6.8K
5%
1/16W
************************************************************

Ref. No.

1-418-201-21
1-672-513-11
1-418-563-11
1-418-202-21
1-694-497-11

SWITCH UNIT, MAIN CONTROL
TRANSLATION FLEXIBLE (JACK) BOARD
TERMINAL UNIT, REMOTE
SWITCH UNIT, ZOOM
TERMINAL BOARD, BATTERY

110
112
122
169
207

1-418-564-11
1-418-192-11
1-672-514-11
X-3378-951-1
1-959-252-11

RAY-CATCHER BLOCK UNIT,REMOCON
MICROPHONE UNIT
TRANSLATION FLEXIBLE BOARD
CONTROL SW SUB ASSY, UPPER
HARNESS (GLAY)

208
0 213
215
221
251

1-959-251-11
1-517-843-11
1-672-355-11
1-803-445-11
1-672-356-11

HARNESS (YELLOW)
FLUORESCENT TUBE
LCD DETECTION SW FLEXIBLE BOARD
PANEL, TOUCH
VF/LCD FLEXIBLE BOARD

267
304
306
408
409

1-672-357-11
8-848-732-01
1-758-202-21
1-675-950-11
1-418-191-11

VF FLEXIBLE BOARD
DEVICE, LENS (LSV-620B)
FILTER BLOCK, OPTICAL
MOTOR FLEXIBLE BOARD
SENSOR, MR

Description

Remark

ACCESSORIES & PACKING MATERIALS
*******************************
0

1-418-327-21
1-418-732-21
1-543-793-11
1-543-798-11
1-765-080-11

CHARGER, AC ADAPTOR (AC-VQ800)
REMOTE COMMANDER (RMT-DCM1)
FILTER, CLAMP (FERRITE CORE) (SMALL)
FILTER, CLAMP (FERRITE CORE) (LARGE)
CORD, CONNECTION (STEREO AV) (1.5m)

0

1-790-107-22
1-790-351-11
3-742-854-01
3-866-152-11
3-866-152-21

CORD, POWER
CORD, CONNECTION (ZK-ET1) (1.8m)
LID, BATTERY (for RMT-DCM1)
MANUAL, INSTRUCTION (ENGLISH)
MANUAL, INSTRUCTION (FRENCH) (Canadian)

MISCELLANEOUS
***************
14
56
61
69
78

Part No.

3-987-015-01 BELT (S), SHOULDER
4-220-941-01 ATTACHMENT (TRIPOD)

417
1-452-997-11 ENCODER, MAGNET
M5811 1-698-543-21 MOTOR (STEPPING)
LCD4301 1-803-033-21 INDICATOR MODULE, LIQUID CRYSTAL
LCD4701 8-753-023-89 LCX024AK-5
************************************************************
**************
HARDWARE LIST
**************
#1
7-621-591-00 SCREW +K 2X4
#2
7-623-505-01 LUG, 2
#3
7-628-253-15 SCREW +PS 2X5
************************************************************

6-21
6-21E

The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.

Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.

< PARTS REFERENCE SHEET >
You can find the parts position of mount locations applying to MAIN board of a set.

MAIN DCM–M1
1

2

3

4

5

6

7

SIDE A
8
A

A
B

4008CI

B

IC5002

C

C
D

D

IC8101
1058CI

E

E

F

F
1068CI
IC3004

G

G

IC5404

H

H
1

✄

✄

B EDIS

2

3
1M–MCD

4

NIAM

5

6

7

8
DCM-M1

DCM-M1

Sony Corporation
9-927-635-11

Personal Audio Division Company

– 254 –

1999L05044-1
Printed in Japan C 1999. 12
Published by General Engineering Dept.

DCM-M1
SERVICE MANUAL

US Model
Canadian Model
E Model

2000. 03

SUPPLEMENT-1
File this supplement with the service manual.

Subject:
1. Change of General
2. Correction of Schematic Diagram
3. Change of repair parts
4. Addition of the note about a special tool for ICs.
5. Addition of the instruction manual for Argentina
model.

1.

Change of General

! : Indicates changed portion.
Page

Before Change

After Change

1-14

$
2.

$

Correction of Schematic Diagram
Page 4-49 to 4-50. Location G to H, 14 to 16.
Incorrect

Correct

3.

Change of repair parts (Section 5 Exploded Views/Section 6 Electrical Parts List)

! : Indicates changed portion.
Page

Before Change
Ref. No. Part No.

5-2 Ref No. 52/6-15
5-2 Ref No. 57/6-3
5-6 Ref No. 252/6-1
5-6 Ref No. 266/6-19
5-7

After Change

Description

Remark Ref. No. Part No.

A-3321-881-A POWER BOARD, COMPLETE
A-3321-883-A JACK BOARD, COMPLETE
A-3321-877-A BL BOARD, COMPLETE
A-3321-879-A VF BOARD, COMPLETE
not supplied (IC001)

Description

A-3323-172-A
A-3323-173-A
A-3323-170-A
A-3323-171-A
A-3328-667-A

312

Remark

POWER BOARD ASSY
JACK BOARD ASSY
BL BOARD ASSY
VF BOARD ASSY
CCD BLOCK ASSY

$
310

309

310

309

310

310

307

307
306

306

not
supplied

not
supplied

311

not supplied
(IC001)

not supplied
(IC001)

311

312

$

4.

Additional of the note about a special tool for ICs. (Electrical Parts List MAIN Board)
Note: @ Replacement of the following ICs used in this set requires a special tool.
Therefore, it cannot be replaced.

Page

IC

Page

Ref. No. Part No.

Description

6-9

@IC3009
@IC5301
@IC5403
@IC5404

IC
IC
IC
IC

6-10

@IC8001 8-759-572-52 IC HD6417709BT80A
@IC8002 8-759-572-70 IC KM416S4034CC-C10
@IC8003 8-759-572-70 IC KM416S4034CC-C10

5.

8-752-397-21
8-752-397-34
8-752-390-38
8-759-676-88

Remark

CXZ31021GA
CXD2652AGA
CXD606-112GA
RU6815TC-DCMM1

6-10

IC
Ref. No. Part No.

Description

@IC8005
@IC8101
@IC8102
@IC8103
@IC8501
@IC8601

IC
IC
IC
IC
IC
IC

1-803-635-11
8-752-396-85
8-759-572-71
8-759-572-71
8-759-653-48
8-752-396-81

Remark

WTGA-EKM29U64000-K1
CXD702-102GA
KM416U4104BC-L6
KM416U4104BC-L6
uPD70F3102F1-33-FA1
CXD1405GG

@IC8701 8-752-394-48 IC CXD1404GA

Additional of the instruction manual for Argentina model.

Page

ACCESSORIES & PACKING MATERIALS
Ref. No. Part No.

6-21

Description

Remark

3-866-152-31 MANUAL, INSTRUCTION (SPANISH) (Argentina)

Sony Corporation
9-927-635-81

Personal Audio Division Company

–2–

2000C05044-1D
Printed in Japan C 2000. 3
Published by General Engineering Dept.

DCM-M1
SERVICE MANUAL
2000. 05

SUPPLEMENT-2
File this supplement with the service manual.

Subject:
• Addition of Section 7 Adjustments
• Correction of Schematic Diagrams

US Model
Canadian Model
E Model

7. ADJUSTMENTS
For the adjustment of this set, the test mode and the firmware data writing are provided.
In the test mode, various adjustment, setting, and checking can be made. Also, the firmware data writing is executed when the Main board
itself, or the Flash Memory (IC8005) or MPEG Control (IC8501) on the Main board is replaced.

TABLE OF CONTENTS
7-1.
1-1.
1-2.
1-3.
1-4.
1-5.
1-6.
1-7.

Test Mode ......................................................................
Outline of Test Mode .....................................................
EVF System Adjustment ...............................................
LCD System Adjustment ...............................................
Servo System Adjustment .............................................
MAC Address Setting ....................................................
Touch Panel Adjustment ...............................................
Other Checking .............................................................

3
3
5
8
13
16
20
21

7-2.
2-1.
2-2.
2-3.

Firmware Data Writing Method .....................................
Preparation ....................................................................
Writing to Flash Memory (IC8005) ................................
Writing to MPEG Control (IC8501) ...............................

23
23
26
26

• Adjustment items required at the replacement of main parts and boards
Adjust the items marked with z in the following table when main parts were replaced.

Adjustment items

EVF System
Adjustment

LCD System
Adjustment

Servo System
Adjustment

MAC Address
Setting

Touch Panel
Position
Alignment

Replacement parts

z

MAIN BOARD IC8005 (Flash)
z

MAIN BOARD IC5405 (NV-RAM)
VF BOARD IC4502 (D/A CONV.(EVR))

z
z

LCD BOARD IC4301 (D/A CONV.(EVR))

z

Mecha. Deck Block

z

Touch Panel
*1
LCD Block LCD4301 (LCD Panel)
EVF Block LCD4701 (LCD Panel)

z

z

z

z

Table.7-1
*1
Note: When LCD panel in the LCD block was replaced, first perform the LCD system adjustment, and then the touch panel position
alignment.

–2–

1-1-4. Description of Test Mode Screen

7-1. Test Mode
1-1.

Outline of Test Mode

In the Test mode, this set allows you to adjust the LCD, EVF,
servo, and touch panel and also to set MAC address.

TEST MODE

I TRON
Drive
JAVA APP
JAVA OS
BOOT
I PL
RATE CTL

1-1-1. Equipment Used
In performing the LCD, EVF, and servo adjustment, use the following measuring instruments.
EVF and LCD system adjustment
• Oscilloscope
Dual-trace oscilloscope, band over 30MHz, and delay mode
(Use 10:1 probe unless otherwise specified)
• Frequency counter
• Digital voltmeter
• Adjusting monitor jig
Part code: J-2053-017-A
Servo system adjustment
• MD1 High reflectance pre-mastered disc (TDYS-1)
Part code: 4-963-646-01
• MD1 MO disc
Commercially available SONY MD1 MO disc
(already recorded)
• MD2 MO disc
Commercially available SONY MD2 MO disc

Item No.

Ver.
Ver.
Ver.
Ver.
Ver.
Ver.
Ver.

Ver.
Ver.
Ver.
Ver.
Ver.
Ver.
Ver.

s. sss
s. sss
ssssssss
ssssssss
s. sss
s. sss
s. sss

4–01–01

Drive

Offset
Function code change

0790
: 6C0 DATA : 00 00 00 30 00 00 00 00
Adjustment data and
adjustment status display field

Special data
display field

Test mode item name
display field
Version display field

Fig.7-1-2

made by MD dep.

I TRON
Drive
JAVA APP
JAVA OS
BOOT
I PL
RATE CTL

Item No.

Test mode item
number display field

1-1-2. How to Enter the Test Mode
In the normal mode, set the POWER switch to “CAMERA”.
While pressing u key on the set, press >, >, ., .,
e, E, e, E, y, y keys on the set in this order.
The Test Mode screen (Fig.7-1-1) appears on the LCD and the
Test mode becomes active.

TEST MODE

made by MD dep.

s. sss
s. sss
ssssssss
ssssssss
s. sss
s. sss
s. sss

1) Version display field
The versions of respective programs that compose the set are
displayed.
ITON ............ Version of set program
Drive ............. Version of drive program
JAVA APP ..... Version of JAVA application
JAVA OS ....... Date when JAVA OS was released
BOOT ........... Version of BOOT program
IPL ................ Version of IPL program
RATE CTL ... Version of V850 (IC8501 on Main board)
program
2) Test mode item number display field
Major item number
Medium item number
Minor item number

1–00–00

Item No.

Camera

4–01–01
Fig.7-1-3

Current Test mode item number is used.
The Test mode items are composed of a major item, medium
item, and minor item.
The number displayed in blue is currently active item.

Fig.7-1-1
1-1-3. How to Exit from the Test Mode
Turn the power off.
Note: In the Test mode, the POWER switch is inactive and therefore disconnect AC adapter to turn the power off.

3) Test mode item name display field
Major item name

Drive

Medium
item name

Offset
Function code change
Minor item name

Fig.7-1-4
Major item, medium item, and minor item of current test mode
item are displayed respectively.

–3–

4) Adjustment data and adjustment status display field
For the items in which there are adjustment data, the data being adjusted is displayed.In the EVF and LCD adjustment, if
data are written, the characters are displayed in violet. At the
white balance adjustment in the EVR and LCD adjustment,
“R” or “B” in small size is displayed on the side of data.
Also, for automatic adjustment items such as servo auto adjustment among the items in which there is no adjustment data,
“Adjusting”, “OK”, or “NG” is displayed.

3. Switching of screen display
The LCD and EVF adjustment contains the items that require
the screen display to be switched to the test signal screen.
• Color bar display method (MENU key)
When major item is in the LCD state (item number: 3), press
the MENU key, and the screen display will be switched to
the color bar display.
To return to the test mode screen, press the MENU key once
more.

5) Special data display field
Only the minor item for Drive and Servo adjustment is displayed. RAM value of address on the drive side is periodically
read and displayed.

• 10-step gradation pattern display method (DSPL key)
Press the DSPL key, and the screen display will be switched
as shown below. (Except Drive and Servo items)

1-1-5. Key Operation in Test Mode
In the Test mode, use the keys on the set for operation.
1. Change or setting of test mode items
• Movement over active item numbers (u, x keys)

Test mode screen
10-step gradation pattern screen
(Set in “EVF” item)

x key moving

Item No.

Camera-through screen

4–01–01

• 10-step gradation pattern setting method (MENU key)
When major item is in the EVF state (item number: 2) and
the 10-step gradation pattern screen is displayed, press the
MENU key, and the screen will be switched to the 10-step
gradation pattern (green) display. Pressing the MENU key
once more causes the screen to be switched to the 10-step
gradation pattern (white/black) display. If this setting is not
made, the 10-step gradation pattern screen is switched to
the camera-through screen.

u key moving

Fig.7-1-5
Use u key when setting active item number and moving
to lower level, or use x key when canceling current item
and moving to higher level.
• Change of active item number (>, ., u keys)
Use > key to raise active item number, or . key to
lower it. For a minor item of Drive and Servo adjustment,
use u key to change the item number.
• Execution or cancellation of active item (y, x keys)
For automatic adjustment items such as servo auto adjustment, pressing y key executes automatic adjustment. To
cancel automatic adjustment, press x key.
2. Change or writing of adjustment data
For the items of LCD and EVF adjustment in which there are
adjustment data, the data can be changed or written by a key
operation.

1-1-6. Test Mode Configuration
The Test mode (major item) is composed of the following items.
Camera (item number: 1) ... Not used.
EVF (item number: 2) ........ Use for EVF system adjustment.
LCD (item number: 3)........ Use for LCD system adjustment.
Drive (item number: 4) ....... Use for checking if an error
occurredin Servo system adjustment.
Audio (item number: 5) ..... Not used.
Power (item number: 6) ..... Not used.
Other (item number: 7) ...... Use for touch panel adjustment,
MAC address setting, or other
checking.
Servo (item number: 8) ...... Use for Servo system adjustment.

• Change of adjustment data (e, E keys)
Use e key to increase the adjustment data, or E key to
reduce it.
• Writing of adjustment data (y key)
Pressing y key causes the adjustment data to be written to
nonvolatile memory.
At this time, the displayed adjustment data characters
changes to violet in color. (Unless this operation is performed, new adjustment data are not stored in nonvolatile
memory)

–4–

1-2.

EVF System Adjustment

Note 1: The backlight (fluorescent tube) is driven with high voltage AC power. Accordingly, do not touch the backlight
holder; otherwise you could receive an electric shock.
Note 2: Take extreme care not to destroy the LCD unit by static
electricity, when replacing it.
Note 3: On the Menu screen, set the “Finder Brightness” to the
center.
Note 4: Once the 10-step gradation pattern (white/black) has been
set, it is held until the power is turned off. Therefore, it
is not necessarily set every time in successive adjustment.

[Connector for adjustment]
The measurement points for EVF adjustment are concentrated on
the CN4901 on the VF board. Connect a measuring instrument to
it via adjusting monitor jig (J-2503-017-A).
The following table lists the pin No. and signal name of CN4901.

[Adjustment steps]
The EVF adjustment, as a rule, should be performed following the
steps given below.
Only for the “Backlight Consumed Current Adjustment”, the order may be changed.
1. EVF Adjustment Data Initializing
2. VCO Adjustment
3. Brightness Adjustment
4. Contrast Adjustment
5. Backlight Consumed Current Adjustment
6. White Balance Adjustment

Pin No.
VF board
Adjustment
CN4901
monitor jig

Signal name

5

A

EVF_GND

4

B

G

3

C

EVF_BL_4.95V (–)

2

D

EVF_BL_4.95V

1

E

VCO

–

F

NC

–

G

NC

–

H

NC

–

I

NC

–

J

NC

Table.7-1-1

VF board CN4901
1
5

Use the connector with EVF labeling.

A
B
C
D
E
F
G
H
I
J
Adjusting monitor jig
(J-2503-017-A)

Fig.7-1-6

–5–

1. EVF Adjustment Data Initializing
Item number

3. Brightness Adjustment
Set the VIDEO signal level that drives the LCD (of EVF) to proper
value.
If deviated, the EVF screen will be unclear, black blurring, or white
blurring.

2-03-01

Screen display Test mode screen
Adjusting method
1) Select the item number “2-03-01”.
2) Press y key to execute the adjustment data initializing.
Check that “OK!” is displayed on the test mode screen.
3) Move to the item number “2-01-ss”, and check that the adjustment data of each minor item is initial value. (See the following table)
Item No.

Initial Data

2-1-1

83

VCO adjustment

2-1-2

90

BRIGHT adjustment

2-1-3

B5

CONTRAST adjustment

2-1-4

B8

Back Light adjustment

2-1-5

R data: 97
B data: 57

Item number

Minor item name

2-01-02

Screen display

Arbitrary

Measurement point

Adjusting monitor jig B pin (G)

Measuring instrument

Oscilloscope

Adjustment data
initial value

90

Adjustment value

A = 7.1 ± 0.1 Vp-p

Adjusting method
1) Select the item number “2-01-02”.
2) Using e and E keys, change the adjustment data so that the
voltage (A) between pedestal of inverted waveform and pedestal of non-inverted waveform satisfies the adjustment value.
3) Press y key to write the adjustment data.

White balance adjustment

Pedestal

Table.7-1-2
Note: To switch between R data and B data of “White Balance
Adjustment”, press u key. After checking the data, move
to other item with R data kept displayed.
A

2. VCO Adjustment
Set free running frequency of VCO.
Item number

2-01-01

Screen display

Arbitrary

Measurement point

Adjusting monitor jig E pin (VCO)

Measuring instrument

Oscilloscope (DC range)

Adjustment data
initial value

83

Adjustment value

A = 1.80 ± 0.05 V

Pedestal
2H

Fig.7-1-8

Adjusting method
1) Select the item number “2-01-01”.
2) Check the GND level of oscilloscope.
3) Using e and E keys, change the adjustment data so that the
VCO output voltage (A) satisfies the adjustment value.
4) Press y key to write the adjustment data.
H

A
GND level
(0Vdc)

Fig.7-1-7

–6–

4. Contrast Adjustment
Set the VIDEO signal level that drives the LCD to proper value.
If deviated, the EVF screen will be unclear, black blurring, or white
blurring.

5. Backlight Consumed Current Adjustment
Set the brightness of backlight.
If deviated, the picture will be too dark or too bright.
Item number

2-01-04

Item number

2-01-03

Screen display

10-step gradation pattern (white/black)

Screen display

10-step gradation pattern (white/black)

Measurement point

Measurement point

Adjusting monitor jig B pin (G)

Measuring instrument

Oscilloscope

Adjustment data
initial value

B5

+ probe: Adjusting monitor jig D pin
(BL+)
– probe: Adjusting monitor jig C pin
(BL–)

Adjustment value

A = 2.1 ± 0.1 Vp-p

Adjusting method
1) Set the 10-step gradation pattern (white/black).
2) Select the item number “2-01-03”.
3) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the EVF screen.
4) Using e and E keys, change the adjustment data so that the
voltage (A) between pedestal (0 IRE) and 100 IRE satisfies
the adjustment value.
5) Press y key to write the adjustment data.
6) Press the DSPL key to return the EVF screen to the test mode
screen.

100 IRE

Measuring instrument

Digital voltmeter

Adjustment data
initial value

B8

Adjustment value

A = 21.0 ± 1.0 mV

Note: After turning on the power, wait for more than 30 seconds,
and then start the adjustment.
Adjusting method
1) Set the 10-step gradation pattern (white/black).
2) Select the item number “2-01-04”.
3) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the EVF screen.
4) Using e and E keys, change the adjustment data so that potential difference (A) between adjusting monitor jig D pin
(BL+) and C pin (BL–) satisfies the adjustment value.
5) Press y key to write the adjustment data.
6) Press the DSPL key to return the EVF screen to the test mode
screen.
6. White Balance Adjustment
Adjust the white balance properly.
If deviated, the color reproducibility of EVF screen will be poor.

A
Pedestal(0 IRE)

Item number
2H

Fig.7-1-9

2-01-05

Screen display

10-step gradation pattern (white/black)

Measurement point
Measuring instrument

Check on the EVF screen

Adjustment data
initial value

R data: 97
B data: 57

Adjustment value

EVF screen must not be colored

Note: To switch between R data and B data, press u key.
After the adjustment finished, move to other item with R
data kept displayed.
Adjusting method
1) Set the 10-step gradation pattern (white/black).
2) Select the item number “2-01-05”.
3) Set the adjustment data to initial value (R data:97, B data:57).
Note: Each time the data is set, press y key to write data to
nonvolatile memory.
4) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the EVF screen.
5) Check that the EVF screen is not colored.
If colored, change the adjustment data by using e and E keys
so that the EVF screen is not colored.
Note: Each time the data is set, press y key to write data to
nonvolatile memory.
6) Press the DSPL key to return the EVF screen to the test mode
screen.

–7–

1-3.

LCD System Adjustment

Note 1: The backlight (fluorescent tube) is driven with high voltage AC power. Accordingly, do not touch the backlight
holder; otherwise you could receive an electric shock.
Note 2: Take extreme care not to destroy the LCD unit by static
electricity, when replacing it.
Note 3: On the Menu screen, set the “Panel Brightness” and
“Panel Color Density” to the center.
Note 4: Once the 10-step gradation pattern (white/black) has been
set, it is held until the power is turned off. Therefore, it
is not necessarily set every time in successive adjustment.

[Connector for adjustment]
The measurement points for LCD adjustment are concentrated on
the CN4305 on the LCD board.
Connect a measuring instrument to it via adjusting monitor jig
(J-2503-017-A).
The following table lists the pin No. and signal name of CN4305.
Use the connector with LCD labeling.
Pin No.
LCD board Adjustment
CN4305
monitor jig
9
A

[Adjustment steps]
The LCD adjustment, as a rule, should be performed following
the steps given below.
Only for the “Backlight Consumed Current Adjustment”, the order may be changed.
1. LCD Adjustment Data Initializing
2. VCO Adjustment
3. Horizontal Position Adjustment
4. RGB D Range Adjustment
5. Brightness Adjustment
6. Contrast Adjustment
7. V-COM Level Adjustment
8. Color Adjustment
9. V-COM Adjustment
10. Backlight Consumed Current Adjustment
11. White Balance Adjustment

Signal name
XTST

8

B

SYF

7

C

HSY

6

D

PANEL_XHD

5

E

GND

4

F

PANEL_COM

3

G

VG

2

H

BL (+)

1

I

BL (–)

–

J

NC

Table.7-1-3

LCD board CN4305

9

1

Use the connector
with LCD labeling.

A
B
C
D
E
F
G
H
I
J
Adjusting monitor jig
(J-2503-017-A)

Fig.7-1-10

–8–

1. LCD Adjustment Data Initializing
Item number

3. Horizontal Position Adjustment
Adjust the display position on LCD panel properly.

3-03-01
Item number

Screen display Test mode screen
Adjusting method
1) Select item number “3-03-01”.
2) Press y key to execute the adjustment data initializing.
Check that “OK!” is displayed on the test mode screen.
3) Move to the item number “3-01-ss”, and check that the adjustment data of each minor item is initial value. (See the following table)
Item No.
3-1-1

Initial Data
BF

Minor item name
VCO adjustment

3-1-2

5D

Flat Position adjustment

3-1-3

80

RGB D-range adjustment

3-1-4

7C

BRIGHT adjustment

3-1-5

D5

CONTRAST adjustment

3-1-6

A8

V-COM level adjustment

3-1-7

76

COLOR adjustment

3-1-8

9C

V-COM adjustment

3-1-9

B6

Back Light adjustment

3-1-A

R data: 95
B data: 70

3-01-02

Screen display

Color bar

Measurement point

CH1: Adjusting monitor jig D pin
(PANEL XHD)
CH2: Adjusting monitor jig C pin
(HSY)

Measuring instrument

Oscilloscope

Adjustment data
initial value

5D

Adjustment value

T = 0.65 ± 0.1 µsec

Adjusting method
1) Select the item number “3-01-02”.
2) Press the MENU key to display color bar on the LCD screen.
3) Using e and E keys, change the adjustment data so that the
falling time difference (T) between PANEL XHD signal and
HSY signal satisfies the adjustment value.
4) Press y key to write the adjustment data.
5) Press the MENU key to return the LCD screen to the test mode
screen.

White balance adjustment

CH1

Table.7-1-4
Note: To switch between R data and B data of “White Balance
Adjustment”, press u key. After checking the data, move
to other item with R data kept displayed.

CH2

2. VCO Adjustment
Set free running frequency of VCO.
enlargement

Item number

3-01-01

Screen display

Arbitrary

Measurement point

Adjusting monitor jig C pin (HSY)

Measuring instrument

Frequency counter

Adjustment data
initial value

BF

Adjustment value

f = 15734 ± 30 Hz

CH1

CH2

Adjusting method
1) Select the item number “3-01-01”.
2) Connect the adjusting monitor jig B pin (SYF) and E pin
(GND).
3) Using e and E keys, change the adjustment data so that the
VCO frequency (f) satisfies the adjustment value.
4) Press y key to write the adjustment data.
5) Disconnect the adjusting monitor jig B pin (SYF) and E pin
(GND).

–9–

T

Fig.7-1-11

4. RGB D Range Adjustment
Set the D range of RGB decoder driver step-wise output that drives
the
LCD to proper value.
If deviated, the LCD screen will be black blurring or white blurring.
Item number

3-01-03

Screen display

10-step gradation pattern (white/black)

Measurement point

Adjusting monitor jig G pin (VG)

Measuring instrument

5. Brightness Adjustment
Set the VIDEO signal level that drives the LCD to proper value.
If deviated, the LCD screen will be unclear, black blurring, or white
blurring.
Item number

3-01-04

Screen display

10-step gradation pattern (white/black)

Measurement point

Adjusting monitor jig G pin (VG)

Measuring instrument

Oscilloscope

Oscilloscope

Adjustment data
initial value

7C

Adjustment data
initial value

80

Adjustment value

A = 1.40 ± 0.05 Vp-p

Adjustment value

A = 3.00 ± 0.05 Vp-p

Note: This is the tracking adjustment in relation to “6. Contrast
Adjustment”.

Adjusting method
1) Select major item number “2” (EVF), and set the 10-step gradation pattern (white/black).
2) Select the item number “3-01-03”.
3) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the LCD screen.
4) Using e and E keys, change the adjustment data so that the
voltage (A) between pedestal of inverted waveform and pedestal of non-inverted waveform satisfies the adjustment value.
5) Press y key to write the adjustment data.
6) Press the DSPL key to return the LCD screen to the test mode
screen.
Pedestal

A

Adjusting method
1) Select major item number “2” (EVF), and set the 10-step gradation pattern (white/black).
2) Select the item number “3-01-04”.
3) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the LCD screen.
4) Connect the adjusting monitor jig A pin (XTST) and E pin
(GND).
5) Using e and E keys, change the adjustment data so that the
voltage (A) between pedestal (0 IRE) and GAMMA1 limiter
level satisfies the adjustment value.
6) Press y key to write the adjustment data.
7) Disconnect the adjusting monitor jig A pin (XTST) and E
pin (GND).
8) Press the DSPL key to return the LCD screen to the test mode
screen.
9) Check that the adjustment value of “Contrast Adjustment” is
satisfied.
If not satisfied, perform “Contrast Adjustment”.

GAMMA1
limiter level

Pedestal
2H

Fig.7-1-12

A

Pedestal(0 IRE)
2H

Fig.7-1-13

– 10 –

6. Contrast Adjustment
Set the VIDEO signal level that drives the LCD to proper value.
If deviated, the LCD screen will be unclear, black blurring, or white
blurring.

7. V-COM Level Adjustment
Set common electrode drive signal level of the LCD panel to proper
value.
Item number

3-01-06

Item number

3-01-05

Screen display

10-step gradation pattern (white/black)

Screen display

10-step gradation pattern (white/black)

Measurement point

Measurement point

Adjusting monitor jig G pin (VG)

Adjusting monitor jig F pin
(PANEL COM)

Measuring instrument

Oscilloscope

Measuring instrument

Oscilloscope

Adjustment data
initial value

D5

Adjustment data
initial value

A8

Adjustment value

A = 2.54 ± 0.05 Vp-p

Adjustment value

A = 4.95 ± 0.05 Vp-p

Note: This is the tracking adjustment in relation to “5. Brightness Adjustment”.
Adjusting method
1) Select major item number “2” (EVF), and set the 10-step gradation pattern (white/black).
2) Select the item number “3-01-05”.
3) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the LCD screen.
4) Using e and E keys, change the adjustment data so that the
voltage (A) between pedestal (0 IRE) and 100 IRE satisfies
the adjustment value.
5) Press y key to write the adjustment data.
6) Press the DSPL key to return the LCD screen to the test mode
screen.
7) Check that the adjustment value of “Brightness Adjustment”
is satisfied.
If not satisfied, perform “Brightness Adjustment”.

Adjusting method
1) Select major item number “2” (EVF), and set the 10-step gradation pattern (white/black).
2) Select the item number “3-01-06”.
3) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the LCD screen.
4) Using e and E keys, change the adjustment data so that the
V-COM signal level satisfies the adjustment value.
5) Press y key to write the adjustment data.
6) Press the DSPL key to return the LCD screen to the test mode
screen.

A

100 IRE
2H

Fig.7-1-15
A

Pedestal(0 IRE)
2H

Fig.7-1-14

– 11 –

8. Color Adjustment
Set the color density to the specified value.
If deviated, the color will be too dark or too light.
Item number

3-01-07

Screen display

Color bar

Measurement point

Adjusting monitor jig G pin (VG)

Measuring instrument

Oscilloscope

Adjustment data
initial value
Adjustment value

9. V-COM Adjustment
Set DC bias of common electrode drive signals for the LCD panel
to proper value.
If deviated, the LCD screen will be unstable where flickering or
vertical streaks appear.
Item number

3-01-08

Screen display

Test mode screen

76

Measurement point
Measuring instrument

Check on LCD screen

A = 0.15 ± 0.05 Vp-p

Adjustment data
initial value

9C

Adjustment value

Fig. 7-1-17

Adjusting method
1) Select the item number “3-01-07”.
2) Press the MENU key to display color bar on the LCD screen.
3) Using e and E keys, change the adjustment data so that a
difference (A) between white signal level and green signal level
satisfies the adjustment value.
4) Press y key to write the adjustment data.
5) Press the MENU key to return the LCD screen to the test mode
screen.
White

Note: This adjustment must be performed after performing
“Brightness Adjustment” and “Contrast Adjustment”.
Adjusting method
1) Select the item number “3-01-08”.
2) Set the adjustment data to initial value (9C).
3) Check that the density of character “e” on the LCD screen is
same (see Fig. 7-1-17). If different, change the adjustment data
by using e and E keys so as to attain the same density of
character “e”.
4) Press y key to write the adjustment data.

A

TEST MODE

made by MD dep.

I TRON
Drive
JAVA APP
JAVA OS
BOOT
I PL
RATE CTL

Green

Item No.

Ver.
Ver.
Ver.
Ver.
Ver.
Ver.
Ver.

s. sss
s. sss
ssssssss
ssssssss
s. sss
s. sss
s. sss

3–01–08

LCD Panel

Adust

V–COM adjst

9C

2H

Fig.7-1-16

enlargement

NG

OK

Fig.7-1-17

– 12 –

NG

10. Backlight Consumed Current Adjustment
Set the brightness of backlight.
If deviated, the picture will be too dark or too bright.
Item number

3-01-09

Screen display

Color bar

Measurement point

+ probe: Adjusting monitor jig I pin
(BL+)
_ probe: Adjusting monitor jig H pin
(BL–)

Measuring instrument

Digital voltmeter

Adjustment data
initial value

B6

Adjustment value

A = 66.0 ± 1.0 mV

1-4.

Servo System Adjustment

1. Servo Auto Adjustment
The servo auto adjustment is executed automatically so that the
adjustment data of the servo system meets the optical pick-up block
in that set.
The servo auto adjustment checks the type of inserted disc and
executes automatically the adjustment that meets the inserted disc.
If the optical pick-up block or IC5405 on the Main board was
replaced, perform the servo auto adjustment with the following
three types of discs respectively.
• MD1 High reflectance pre-mastered disc (TDYS-1)
Part code: 4-963-646-01
• MD1 MO disc
Commercially available SONY MD1 MO disc (already recorded)
• MD2 MO disc
Commercially available SONY MD2 MO disc

Note: Use AC adapter whenever performing this adjustment.
After turning on the power, wait for more than 30 seconds,
and then start the adjustment.
Adjusting method
1) Select the item number “3-01-09”.
2) Press the MENU key to display color bar on the LCD screen.
3) Using e and E keys, change the adjustment data so that potential difference (A) between adjusting monitor jig I pin
(BL+) and H pin (BL–) satisfies the adjustment value.
4) Press y key to write the adjustment data.
5) Press the MENU key to return the LCD screen to the test mode
screen.

Adjusting method
1) Select the item number “8-01-01”.
2) Insert the desired type of disc to be adjusted.
3) Press y key to execute the servo auto adjustment. (Auto adjustment will start and “Now Adjusting ... ss” will be displayed in the adjustment status display field.)
Note: Place the set horizontally and perform adjustment under stable condition.

TEST MODE

I TRON
Drive
JAVA APP
JAVA OS
BOOT
I PL
RATE CTL

11. White Balance Adjustment
Adjust the white balance properly.
If deviated, the color reproducibility of LCD screen will be poor.
Item number

Item No.

3-01-0A

Screen display

10-step gradation pattern (white/black)

Measurement point
Measuring instrument

Check on the LCD screen

Adjustment data
initial value

R data: 95
B data: 70

Adjustment value

LCD screen must not be colored

made by MD dep.

Ver.
Ver.
Ver.
Ver.
Ver.
Ver.
Ver.

s. sss
s. sss
ssssssss
ssssssss
s. sss
s. sss
s. sss

8–01–01

Servo

Servo Common
All Adjust START
Now Adjusting . . . ss

: 6C0 DATA : 00 00 00 30 00 00 00 00
Adjustment status display field

Note: To switch between R data and B data, press u key.
After the adjustment finished, move to other item with R
data kept displayed.
Adjusting method
1) Select major item number “2” (EVF), and set the 10-step gradation pattern (white/black).
2) Select the item number “3-01-0A”.
3) Set the adjustment data to initial value (R data:95, B data:70).
Note: Each time the data is set, press y key to write data to
nonvolatile memory.
4) Press the DSPL key to display the 10-step gradation pattern
(white/black) on the LCD screen.
5) Check that the LCD screen is not colored.
If colored, change the adjustment data by using e and E keys
so that the LCD screen is not colored.
Note: Each time the data is set, press y key to write data to
nonvolatile memory.
6) Press the DSPL key to return the LCD screen to the test mode
screen.

Fig.7-1-18
4) At the completion of adjustment, the adjustment result will be
displayed in the adjustment status display field.
Note: If an error occurs during adjustment, you can check
the item name where the error occurred. (Refer to
“Faulty item checking method”.)
• In case of successful adjustment

OK!
• In case of NG adjustment

NG

NG. ss ss
A

Fig.7-1-19
5) Remove the disc inserted in step 2).

– 13 –

Faulty item checking method
1) From the adjustment status display screen at “NG” (Fig.7-119), read a 2-digit number at part “A”.
Example: On the following screen, if adjustment finished, “78” is
displayed.

TEST MODE

made by MD dep.

I TRON
Drive
JAVA APP
JAVA OS
BOOT
I PL
RATE CTL
Item No.

Ver.
Ver.
Ver.
Ver.
Ver.
Ver.
Ver.

s. sss
s. sss
ssssssss
ssssssss
s. sss
s. sss
s. sss

8–01–01

Servo

Servo Common
All Adjust START

NG NG. 78 ss
: 6C0 DATA : 00 00 00 30 00 00 00 00
Fig.7-1-20
2) Move over major item to Drive (item number: 4).
3) Set medium item number to higher digit of the number read in
step 1).
Example: If the read number is “78”, medium item number is 7.
4) Set minor item number to lower digit of the number read in
step 1).
At this time, the medium item name and minor item name on
the screen indicate the adjustment item names where an error
occurred during servo auto adjustment.
Example: If the read number is “78”, minor item number is 8.

TEST MODE

made by MD dep.

I TRON
Drive
JAVA APP
JAVA OS
BOOT
I PL
RATE CTL
Item No.

Ver.
Ver.
Ver.
Ver.
Ver.
Ver.
Ver.

s. sss
s. sss
ssssssss
ssssssss
s. sss
s. sss
s. sss

4–07–08

Drive

MD1 GRV adj
MD1 GRV F-BIAS (ADIP)

0790
: 6C0 DATA : 00 00 00 30 00 00 00 00

Fig.7-1-21
Then, from the medium item name and minor item name, you
can confirm that a fault occurred in “MD1 GRV F-BIAS
(ADIP)” item of the “MD1 GRV adj”.

– 14 –

2. Mecha. Deck Block Primary Check
The following parts of the mecha. deck block can be checked in a
simple check.
• Laser diode
• Focus coil
• Spindle motor
• Disc type check switch
• Sled motor
• Tracking coil
• INITIAL SW
• HEAD UP/DOWN motor
• INITIAL SW
Note: To check the operation of mecha. deck block, remove the
Upper Panel Assembly. (See 2. Removal on page 2-9)

Checking method
1) In the normal mode, set the POWER switch to “CAMERA”.
2) Check that “DISC LID IS OPEN” is displayed on the LCD
screen.
3) Press the part A to check that the part B lights in red and
moves up and down. (Laser diode check, Focus coil check)
Also, check that the spindle motor rotates at this time. (Spindle
motor check)
Note: If the part A is released once and then pressed again, the
operation restarts though the operation time is short.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.

D

X

B
OPTICAL PICK-UP block

Spindle Motor

A
C

MD1/MD2
PIT/GRV
PROTECT SW

Fig.7-1-22

– 15 –

4) Operating the keys on the set, enter the Test mode.
5) Select the item “7-02-01” and press u key to activate the
Switch Check mode.
Note: When the Switch Check mode becomes active, the
screen as shown in Fig.7-1-23 appears.

LCD

CLOSE
OFF

REVERSE/CLOSE
IN LIMIT SW
INITIAL SW
MD1/MD2
PIT/GRV
PROTECT SW

OFF
OFF
MD2
GRV
ON

D 1 (decimal)
327679 or less

D2 (decimal)
D1-262144

H1 (hexadecimal)
04

327680 or more

D1-327680

05

Table 7-1-6

LCD switch status display
Mecha. deck switch status display
Set switch status display

Fig.7-1-23
6) Press each switch at part C to check that the mecha. deck
switch status display on the LCD screen changes as listed below. (Disc type check switch)
Switch name

When not pressed

When pressed

MD1/MD2

MD2

MD1

PIT/GRV

GRV

PIT

PROTECT SW

ON

OFF

MAC Address Setting

The MAC address must be unique in the world.
On this set, hexadecimal MAC address is set for every serial number of the set.
1. How to Get MAC Address
1) Read the lower 5 digits of serial No. and add “291903 (decimal)” to it, which is assumed to be D 1.
D1 = “Lower 5 digits of serial No.” + 291903
Example: If the lower 5 digits of serial No. is “03574”
D1 = 3574 + 291903 = 295477
2) From Table 7-1-6, obtain D2 and H1 that correspond to D 1
Example: If D1 = 295477
D2 = 295477 – 262144 = 33333
H1 = 04

SW CHECK MODE
COVER
EJECT SW

1-5.

Table 7-1-5
7) Check that the Optical Pick-up block moves outward when
> key is pressed, or it moves inward when . key is
pressed. (Sled motor check)
8) At this time, check that the part B also moves in the same
direction as the direction in which the Optical Pick-up block
moves. (Tracking coil check)
9) Check that when the Optical Pick-up block moves inward as
far as it will go, the IN LIMIT SW status display on the LCD
screen is “ON” and when it moves outward, the switch becomes “OFF”. (IN LIMIT SW check)
10) Check that the part D moves in arrow direction when y key
is pressed, and it returns to original position when y key is
pressed once more. (HEAD UP/DOWN motor check)
11) At this time, check that each time the y key is pressed, the
INITIAL SW status display on the LCD screen changes over
between “ON” and “OFF”. (INITIAL SW check)
12) Turn the power off.
Note: Disconnect the AC adapter to turn the power off, because the POWER switch is inactive in the Test mode.

3) From Table 7-1-7, obtain maximum decimal number not exceeding D2, which is assumed to be D3.
Example: If D2 = 33333
D3 = 33280
4) From Table 7-1-7, obtain hexadecimal number that corresponds
to D3, and the higher 2 digits of that number is assumed to be
H3.
Example: If D3 = 33280
H3 = 82
5) Obtain a difference between D2 and D 3, which assumed to be
D4. (0 ≤ D4 ≤ 255)
D4 = D 2 – D 3
Example: If D2 = 33333 and D3 = 33280,
D4 = 33333 – 33280 = 53
6) From Table 7-1-8, convert D4 into hexadecimal number to obtain H4 .
Example: If D4 = 53
H4 = 35
7) The MAC address is “08:00:46:H 1:H3:H4”. (08, 00, 46 are fixed
values)
Example: If H1 = 04, H3 = 82 and H4 = 35
08:00:46:04:82:35

– 16 –

D3
0

H3
0000

D3
8192

H3
2000

D3
16384

H3
4000

D3
24576

H3
6000

D3
32768

H3
8000

D3
40960

H3
A000

D3
49152

H3
C000

D3
57344

H3
E000

256
512

0100
0200

8448
8704

2100
2200

16640
16896

4100
4200

24832
25088

6100
6200

33024
33280

8100
8200

41216
41472

A100
A200

49408
49664

C100
C200

57600
57856

E100
E200

768
1024

0300
0400

8960
9216

2300
2400

17152
17408

4300
4400

25344
25600

6300
6400

33536
33792

8300
8400

41728
41984

A300
A400

49920
50176

C300
C400

58112
58368

E300
E400

1280
1536

0500
0600

9472
9728

2500
2600

17664
17920

4500
4600

25856
26112

6500
6600

34048
34304

8500
8600

42240
42496

A500
A600

50432
50688

C500
C600

58624
58880

E500
E600

1792
2048

0700
0800

9984
10240

2700
2800

18176
18432

4700
4800

26368
26624

6700
6800

34560
34816

8700
8800

42752
43008

A700
A800

50944
51200

C700
C800

59136
59392

E700
E800

2304
2560

0900
0A00

10496
10752

2900
2A00

18688
18944

4900
4A00

26880
27136

6900
6A00

35072
35328

8900
8A00

43264 A900 51456 C900 59648
43520 AA00 51712 CA00 59904

E900
EA00

2816
3072

0B00
0C00

11008
11264

2B00
2C00

19200
19456

4B00
4C00

27392
27648

6B00
6C00

35584
35840

8B00
8C00

43776 AB00 51968
44032 AC00 52224

60160
60416

EB00
EC00

3328
3584

0D00
0E00

11520
11776

2D00
2E00

19712
19968

4D00
4E00

27904
28160

6D00
6E00

36096
36352

8D00
8E00

44288 AD00 52480 CD00 60672
44544 AE00 52736 CE00 60928

ED00
EE00

3840
4096

0F00
1000

12032
12288

2F00
3000

20224
20480

4F00
5000

28416
28672

6F00
7000

36608
36864

8F00
9000

44800
45056

AF00
B000

52992
53248

CF00
D000

61184
61440

EF00
F000

4352
4608

1100
1200

12544
12800

3100
3200

20736
20992

5100
5200

28928
29184

7100
7200

37120
37376

9100
9200

45312
45568

B100
B200

53504
53760

D100
D200

61696
61952

F100
F200

4864
5120

1300
1400

13056
13312

3300
3400

21248
21504

5300
5400

29440
29696

7300
7400

37632
37888

9300
9400

45824
46080

B300
B400

54016
54272

D300
D400

62208
62464

F300
F400

5376
5632

1500
1600

13568
13824

3500
3600

21760
22016

5500
5600

29952
30208

7500
7600

38144
38400

9500
9600

46336
46592

B500
B600

54528
54784

D500
D600

62720
62976

F500
F600

5888
6144
6400

1700
1800
1900

14080
14336
14592

3700
3800
3900

22272
22528
22784

5700
5800
5900

30464
30720
30976

7700
7800
7900

38656
38912
39168

9700
9800
9900

46848
47104
47360

B700
B800
B900

55040
55296
55552

D700
D800
D900

63232
63488
63744

F700
F800
F900

6656
6912

1A00
1B00

14848
15104

3A00
3B00

23040
23296

5A00
5B00

31232
31488

7A00
7B00

39424
39680

9A00
9B00

47616
47872

BA00
BB00

55808 DA00 64000
56064 DB00 64256

FA00
FB00

7168
7424

1C00
1D00

15360
15616

3C00
3D00

23552
23808

5C00
5D00

31744
32000

7C00
7D00

39936
40192

9C00
9D00

48128 BC00 56320 DC00 64512
48384 BD00 56576 DD00 64768

FC00
FD00

7680
7936

1E00
1F00

15872
16128

3E00
3F00

24064
24320

5E00
5F00

32256
32512

7E00
7F00

40448
40704

9E00
9F00

48640
48896

FE00
FF00

Note: D3: Decimal
H3: Hexadecimal

Table 7-1-7

– 17 –

BE00
BF00

56832
57088

CB00
CC00

DE00
DF00

65024
65280

Hexadecimal-decimal Conversion Table
Lower digit of
hexadecimal

0

1

2

3

2
4

5

6

7

8

9

A
(A)

B
(b)

C
(c)

D
(d)

E
(E)

F
(F)

Upper digit
of hexadecimal

1

0

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

1

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

2

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

3

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

4

64

65

66

67

68

69

70

71

72

73

74

77

76

77

78

79

5

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

6

96

97

98

99

100

101

102

103

104

105

106

107

108

109

110

111

7

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

8

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

9

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

A (A)

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

B (b)

176

179

180

181

182

183

184

185

186

187

188

189

190

191

C (c)

177
193

178

192

194

195

196

197

198

199

200

201

202

203

204

205

206

207

D (d)

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

E (E)

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

F (F)

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

255

Example: If decimal number is “53”, the higher digit 1 of hexadecimal number is “3”
and the lower digit 2 is “5”, and thus “35” is the hexadecimal number to be obtained.

Table 7-1-8

– 18 –

2. MAC Address Setting Method
1) Select the item number “7-01-01”.
2) Press u key to activate the MAC Address Set mode.
(When the MAC Address Set mode becomes active, the MAC
address is displayed as shown in Fig.7-1-24)

TEST MODE

made by MD dep.

ITRON
Drive
JAVA APP
JAVA OS
BOOT
IPL
RATE CTL
Item No.

Ver.
Ver.
Ver.
Ver.
Ver.
Ver.
Ver.

s. sss
s. sss
ssssssss
ssssssss
s. sss
s. sss
s. sss

7–01–01

Other

Adjust

MAC Address Write
MAC

08 : 00 : 46 : ss : ss : ss

Moves the cursor by . key

MAC

08 : 00 : 46 : ss : ss : ss

Moves the cursor by > or u key

Fig.7-1-24
3) Operating the keys on the set, set the MAC address.
Note: Set the address values at three places on the right side.
Three address values on the left side are fixed values
and not changeable.
• Key operation
> or u key ...... Moves the cursor to the right.
. key ................. Moves the cursor to the left.
e key ..................... Increases address value at the cursor position.
E key ..................... Decreases address value at the cursor position.
x key ...................... Releases the MAC Address Set mode.
y key .................... Writes MAC address.
4) Press y key to write the MAC address.
Note: Even if the y key is pressed, the screen does not
change. Unless this key is pressed, the set MAC address
is not stored in nonvolatile memory.
Also, the MAC address writing can be done only once
after the power was turned on. To set the MAC address
once more, the power must be turned off, and on again.

– 19 –

1-6.

Touch Panel Adjustment

1. Touch Panel Position Alignment
The touch panel position alignment should be made in both cases
where the LCD screen is opened, and it is closed.
In touching the screen, use the input pen attached.
Adjusting method
1) Select the item number “7-01-02”.
2) Press u key to activate the Touch Panel Position Alignment
mode.
(The screen display will be as shown in Fig.7-1-25)
3) Touch the center of mark displayed at the upper left of LCD
screen.
(The screen display switches to the one shown in Fig.7-1-26)
4) Touch the center of mark displayed at the lower right of LCD
screen.
(The screen display switches to the one shown in Fig.7-1-27)
5) Touch the center of mark displayed in the center of LCD screen.
6) The touch panel position alignment finishes, and the adjustment result is displayed.
• If alignment is successful ........... “OK!”
• If alignment failed ...................... “NG!”
7) If the touch panel alignment is to be made once more by changing the direction of the LCD, press u key to display the screen
shown in Fig.7-1-25, and then perform adjustment after step
3).
Note: If the alignment failed, perform the touch panel position alignment again without changing the LCD direction.
8) At successful completion of the alignment in both cases where
the LCD is opened and closed, press x key to release the Touch
Panel Position Alignment mode.

Touch Panel
Please Touch

Fig.7-1-25

Touch Panel
Please Touch

Fig.7-1-26

Touch Panel
Please Touch

2. Touch Panel Simple Check
Checking method
1) Select the item number “7-01-03”.
2) Check that “OK” is displayed when you touch the LCD screen.

Fig.7-1-27

• In case of successful adjustment

Touch Panel
Please Touch

OK!

• In case of NG adjustment

Touch Panel
Please Touch

NG!

Fig.7-1-28

– 20 –

1-7.

Other Checking

1. Switch Check
In the Switch Check mode, even pressing the x key cannot release the Switch Check mode. To exit from this mode, turn the
power off.
Checking method
1) Select the item number “7-02-01”.
2) Press u key to activate the Switch Check mode.
(The screen display becomes as shown in Fig.7-1-29, and the
detection status of each switch on the set, LCD switch, and
mecha. deck switch is displayed)

2.Key Check
In the Key Check mode, even pressing the x key cannot release
the Key Check mode. To exit from this mode, turn the power off.
Checking method
1) Select the item number “7-02-01”.
2) Press u key to activate the Switch Check mode.
3) From the Switch Check mode, press u key to activate the
Key Check mode. (The screen display becomes as shown in
Fig.7-1-30)

KEY CHECK MODE

SW CHECK MODE

PLAY/EDIT MODE
COVER
EJECT SW
LCD

CLOSE
OFF

ssssss

REVERSE/CLOSE
IN LIMIT SW
INITIAL SW
MD1/MD2
PIT/GRV
PROTECT SW

OFF
OFF
MD2
GRV
ON

000
C control dial status display
A Power switch status display

LCD switch status display
B Set key status display

Set switch status display
Mecha. deck switch status display

Fig.7-1-30
4) Check that the POWER switch detection status displayed at
part A is normal. (See Table below)

Fig.7-1-29
3) Check that each switch is detected normally.
(See Table below. For the mecha. deck switch, see “Mecha.
Deck Block Simple Check”)
• SET switch

COVER
EJCT SW

Display

Condition

OPEN

Disc lid is OPEN

CLOSE

Disc lid is CLOSE

ON

DISC EJECT switch ON

OFF

DISC EJECT switch OFF

Display
NORMAL/CLOSE

LCD panel Condition
NORMAL/CLOSE

NORMAL/OPEN

NORMAL/OPEN

REVERS/CLOSE

REVERSE/CLOSE

REVERS/OPEN

REVERSE/OPEN

• MECHANISM DECK switch
Display
IN LIMIT SW

MD1/MD2

Remark
Condition of OPTICAL PIC-UP in limit
switch
Condition of REC HEAD initial position
detect switch
Condition of MD1/MD2 detect switch

PIT/GRV

Condition of REFLECT switch

PROTECT

Condition of PROTECT detect switch

INITIAL SW

Condition
PLAY/EDIT position

MODE OFF

OFF position

Camera MODE

CAMERA position

Interview MODE

INTERVIEW position

5) Check that a numeric value displayed at part B decreases if
the control dial is rotated clockwise, or increases if counterclockwise.

• LCD switch

LCD

Display
PLAY/EDIT MODE

– 21 –

6) Check that the name associated with the pressed key is displayed at part C if a key on the set is pressed. (See Table
below)
Display
PLAY

Key name
u (PLAY/PAUSE)

STOP

x (STOP)

FF

> (FF)

REW

. (REW)

SLOW

y (SLOW)

A REC

AUDIO REC

V REC

(VIDEO REC)

PON

ENTER

ERASE

ERASE

MENU

MENU

BRIGHT

EXPOSURE

DISPLAY

DSPL

VOLUME +

e (VOL +)

VOLUME –

E (VOL –)

PHOTO

PHOTO

MARK

BACK LIGHT

FORCUS

FORCUS

3. Adjustment Condition Check
In the Adjustment Condition Check mode, current conditions of
servo auto adjustment, MAC address setting, and touch panel position alignment can
be checked.
1) Select the item number “7-02-05”.
2) Press u key to activate the Adjustment Condition Check
mode.
(When the Adjustment Condition Check mode becomes active, the screen changes as shown in Fig.7-1-31, and current
adjustment conditions are displayed)

Adjust Condition
MO CD
MD1 -- OK
MD2 OK NG
Correct a location of Touch Panel

NG
Write MAC address

OK
Condition display of MAC address setting

7) Check that the “KEY CHECK MODE” characters on the screen
change to green in color if all keys on the set are pressed.

Condition display of
touch panel position alignment
Condition display of servo auto adjustment

Fig.7-1-31
• escription of display
OK ........... Adjustment successfully completed
NG ........... Adjustment failed (or not adjusted yet)
– ............... Not adjusted yet (Servo auto adjustment only)
• Key operation
x key ....... Releases the Adjustment Condition Check mode
y key ..... Initializes the Adjustment Condition Check mode
If y key is pressed, the condition display of servo auto adjustment will be all “–”, and that of MAC address setting and touch
panel position alignment will be “NG”. (Fig.7-1-31)
Note: The adjustment data are not initialized even if the Adjustment Condition Check mode is initialized.
4. Set Value Initializing
Each set value on the set can be initialized to the factory setting.
Initializing method
1) Select the item number “7-02-06”.
2) Press y key, and “OK” will be displayed on the screen and
each set value will be initialized to the factory setting.

– 22 –

7-2. Firmware Data Writing Method
Write the data by the method given below, when the Main board
or the Flash Memory (IC8005) and MPEG Control (IC8501)
mounted on the MAIN board were replaced.

2-1.

Preparation

1. Measuring Equipment
To write the data, use measuring equipment listed below:
1) Personal computer (Windows95/98 installed)
2) Hyper Terminal (Communication software attached to the Windows)
3) Firmware Writer Ether Flash BB(U)
Part code: J-2503-019-A
4) MPEG RATE CONTROL
Part code: J-2503-020-s
5) RS-232C Cable D-Sub 9pin (Female) (Cross cable type)
6) Regulated power supply
7) AC Adaptor/Charger (AC-VQ800)
2. Connection
1) Disconnect the CN8801 of ETHER board from the CN8007
of MAIN board, and connect the Ether Flash BB instead.
Note: Be careful of the connection direction when connecting
the Ether Flash BB.
2) Connect the CN7 of Ether Flash BB and the personal computer with the RS-232C Cable (Cross cable type).

Personal computer

to RS-232C

AC adaptor/charger
(AC-VQ800)
*1 MPEG RATE CONTROL

*1 Regulated power supply
(15 Vdc)

Test pins
TP5002
GND

TP8047
TEST

*1 Use the regulated power supply and
MPEG RATE CONTROL when
MPEG Control (IC8501) was replaced.

CN6
2 1

CN7

CN8007
CN3

Ether Flash BB
Cabinet (R)
POWER BOARD

MAIN BOARD

Fig.7-2-1

– 23 –

RS-232C Cable
(Cross cable Type)

3. Hyper Terminal Setting
1) Double-click [Hypertrm.exe] in the Hyper Terminal folder of
the personal computer.
2) On the [Connection Description] screen, enter the name “DCMM1” and select the icon, and then click [OK].

3) On the [Port Settings] screen, set the following and click [OK].
Bits per second: 57600
Data bits: 8
Parity: None
Stop bit: 1
Flow control: Xon/Xoff

Fig.7-2-2
Select [Direct to Com1] for the Connect using: and click [OK].
If Com1 port has been used, select [Direct to Com2].

Fig.7-2-4
4) From the File on the menu bar, click the Properties to select
the Settings screen.
Next, click [ASCII Setup] on the Settings screen.

Fig.7-2-3

Fig.7-2-5

– 24 –

5) On the [ASCII Setup] screen, set the following and click [OK].
[ASCII Sending]
Line delay: [2] milliseconds
[ASCII Receiving]
[Append line feeds to incoming line ends]: [√] marking
[Wrap lines that exceed terminal width]: [√] marking
Next, on the [Settings] screen, click [OK] once more.

4. Setting of the Set
After the Hyper Terminal setting finished, check that the prompt
appears on the screen, and then perform a setting to the set through
the steps given below.
1) Set the POWER switch to PLAY/EDIT.
Note: Setting the POWER switch to CAMERA/INTERVIEW allows the Auto Power OFF function to operate, thus causing the power to be turned off during measurement. Therefore, be sure to set it to PLAY/EDIT.
2) Short the test pins TP8047 (TEST) and TP5002 (GND) with
tweezers, etc.
3) From the AC Adaptor, turn the power on.
4) Remove tweezers to release the test pins.
5) Check that the following message is displayed on the screen.
Board Check Monitor ver1.XXX
5. Exit Hyper Terminal
From the File on the menu bar, click the “Exit Hyper Terminal”.
On the following screen, click [Yes] to finish the Hyper Terminal.

Fig.7-2-7

Fig.7-2-6

– 25 –

2-2.

Writing to Flash Memory (IC8005)

2-3.

Note 1: When the writing to the Flash Memory (IC8005) was
executed, perform the following:
• MAC Address Setting (See Test Mode page 16)
• Touch Panel Adjustment (See Test Mode page 20)
Note 2: Hyper Terminal setting must already be finished.
Note 3:
on typical screen display indicates input characters.
1) Perform a setting to the set. (See page 25)
2) Make “Board Check Monitor ver1.XXX” displayed on the
screen, enter “WT” for the prompt and press the [Enter] key.
3) Data writing to the Flash Memory starts, and the progress status is displayed on the screen as shown below. After about one
minute, [WT>OK] is displayed and the writing finishes.

Board Check Monitor ver1.XXX
> WT
Formatting FLASH file... src=1 ,dst=0
Format done.
Copying file: MDCX_ITRON
@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@
Copying file: MDCX_JAPP
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@
Copying file: MDCX_JAVA
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@
Copying file: MDCX_FTPBT
@@@@@@@@@@@@@@@@@@@@@@@@@@@@
@@@@@@@@@@@@@@@@@@
Copying file: MDCX_FTPD
@@@@@@@@
Copying file: MDCX_WKSCR
@@@@@
Copying file: MDCX_JDICS
@@@@@@@@@@@@@@@@
Copying file: MDCX_EFFECT
@
Copying file: MDCX_SLEEP
@
Copying file: MDCX_VERSION
@
Copying 2nd partition...
End of WT.
WT>OK

Writing to MPEG Control (IC8501)

Note 1: Hyper Terminal setting must already be finished.
Note 2:
on typical screen display indicates input characters.
1)
2)
3)
4)

Insert MPEG RATE CONTROL disc into the drive A.
Perform a setting to the set. (See page 25)
Apply +15Vdc to the CN6 of Ether Flash BB.
Make “Board Check Monitor ver1.XXX” displayed on the
screen, enter “V” for the prompt and press the [Enter] key.
5) After [V850E>] is displayed, enter “R” and press the [Enter]
key.
6) Again, after [V850E>] is displayed, enter “L” and press the
[Enter] key.
7) From the Transfer on the menu bar, click [Send Text File] to
display the [Send Text File] screen.

Fig. 7-2-9
Select [3 1/2 Floppy (A:)] for the Look in, and [All files (*.*)]
for the File type.
Click the “Rom_1000.hex” displayed on the screen to highlight, and click [Open].
The data are then sent and displayed on the screen.
8) After [V850E>] is displayed, enter “A” and press the [Enter]
key.
The Flash Data writing starts, and the following is displayed:
[Program to V850 flash memory finished] Then, [V850E>] is
displayed as a prompt.
9) Enter “Q” to quit the data writing.
10) Exit the Hyper Terminal. (See page 25)
Note 3: Disconnect the +15Vdc applied to the CN6 of Ether Flash
BB in prior to disconnection of the power supply from
the AC Adaptor.

Fig.7-2-8 Typical screen display
4) Exit the Hyper Terminal. (See page 25)

– 26 –

Board Check Monitor ver1.XXX
>V
<< V850E Flash Writer menu V0.203 >>
A ........................... V850E Auto sequence
(Erase, Program,Verify)
R ........................... V850E Device reset
P ........................... V850E Program mode on
I ............................ Initialize parameter
L ........................... Load Motlora S format file
W .......................... Write all flash memory
E ........................... Erase all flash memory (without PreWrite)
C ... Send V850E command
Q ........................... Quit V850 menu
V850E> R
V850E RESET,Vpp=7.8V
V850E> L
S0086262322E6F75747B
S2080000008007C00AA6
S254000130E00F40005C1A630F0100E10F40005C1A630F0
100E087600180FF684BC0FF58F1D20DC0
BF58F1243779860656010064577986005FDAF0465F0000E0
076001230F0100441AE10F2000230F01
00441AE107FF
~ an omission ~
S21500DB5C0000000000000000000000000000000000B3
S804000AC031
V850E> A
V850E RESET,Vpp=7.8V
V850E PROGRAM MODE .... FAILED
V850E PROGRAM MODE .... READY
FREQ SET COMMAND OK
ERASE SET COMMAND OK
WRITE SET COMMAND OK
BAUDRATE SET COMMAND
baudrate 76800bps OK
WRITEBACK SET COMMAND OK
Initialize OK!
WRITE ALL 0
.............................................. OK
ALL ERASE
Waiting ... OK
RESET COMMAND
OK
ALL BLANK CHECK
Waiting ... OK
WRITE START
.............................................. OK
ALL VERIFY
.............................................. OK
Program to V850 flash memory finished.
V850E RESET,Vpp=7.8V
V850E> Q
>

Fig.7-2-10 Typical screen display

– 27 –

• Correction of Schematic Diagrams

! : Indicates changed portion.

MAIN BOARD (1/8) (Page 4-29 to 4-30. Location A to E, 1 to 8)
Incorrect

$
# #
!

%

#

Correct

$
# #
!

%

– 28 –

#

MAIN BOARD (3/8) (Page 4-32. Location E, 28)
Incorrect

Correct

$

$
MAIN BOARD (3/8) (Page 4-32. Location J, 27 to 29)
Incorrect

Correct

^

^
^

^

MAIN BOARD (3/8) (Page 4-39. Location C to E, 1 to 4)
Incorrect

Correct

^^

^^
MAIN BOARD (3/8) (Page 4-39 to 40. Location E, 8 to 10)
Incorrect

Correct

^

^
$

$

MAIN BOARD (3/8) (Page 4-40. Location C to E, 11 to 14)
Incorrect

Correct

#
%
%

#

$

^

%
%

^
– 29 –

^

^

$

MAIN BOARD (3/8) (Page 4-40. Location C, 15 to 19)
Incorrect

Correct

^
$

%
$

MAIN BOARD (3/8) (Page 4-40. Location F to G, 17 to 18)
Incorrect

Correct

%

%

MAIN BOARD (3/8) (Page 4-40. Location J to L, 15 to 18)
Incorrect

Correct

^
@

MAIN BOARD (4/8) (Page 4-44. Location A to B, 14 to 17)
Incorrect

Correct

# $
#$

# $
#$

– 30 –

MAIN BOARD (4/8) (Page 4-44. Location D to E, 14 to 16)
Incorrect

Correct

%

%

MAIN BOARD (4/8) (Page 4-44 to 45. Location J to L, 17 to 19)
Incorrect

Correct

%

%

MAIN BOARD (4/8) (Page 4-45. Location H to J, 24 to 27)
Incorrect

Correct

#

^

MAIN BOARD (4/8) (Page 4-46. Location G to H, 30 to 33)
Incorrect

Correct

%
#

%
#
– 31 –

MAIN BOARD (5/8) (Page 4-48. Location F to G, 1 to 4)
Incorrect

Correct

#

#
MAIN BOARD (8/8) (Page 4-59. Location L, 1 to 4)
Incorrect

Correct

#

#

CLV BOARD (Page 4-77. Location G to H, 12 to 14)
Incorrect

Correct

%

%

#

#

REC BOARD (Page 4-82. Location D to E, 10 to 12)
Incorrect

Correct

#

– 32 –

#

DCM-M1
• Signal Paths were Missing in Service Manual.
LCD (LCD) SCHEMATIC DIAGRAM (Page 4-106 to 4-108)

LCD
– 33 –

– 34 –

– 35 –

LCD

DCM-M1

ETHER BOARD (Page 4-116. Location D, 1 to 3)
Incorrect

Correct

#

#

Sony Corporation
9-927-635-82

Audio Entertainment Group

– 38 –

2000E05035-1
Printed in Japan C 2000. 5
Published by PE General Engineering Dept.

DCM-M1
SERVICE MANUAL

US Model
Canadian Model
E Model

2000. 08

SUPPLEMENT-3
File this supplement with the service manual.

Subject:
• Addition of Section 7 Camera Section Adjustment
• Correction of Schematic Diagrams

7-3. CAMERA SECTION ADJUSTMENT
TABLE OF CONTENTS
3-1. Preparation before Adjustment .................................. 3

3-3. Camera System Adjustment ........................................ 8

3-1-1. Service Tools List ........................................................ 3
3-1-2. Preparation .................................................................. 4
3-1-3. Precautions ................................................................. 5

1.
2.
3.

Zoom Center Adjustment ................................................
Hall Adjustment ...............................................................
Flange Back Adjustment (Using flange back
adjusting chart subject more than 500 m away) .............
4. Flange Back Adjustment (Using mini pattern box) .........
5. Flange Back Check .........................................................
6. Optical Axis Adjustment ..................................................
7. AGC Gain Calibration Adjustment ..................................
8. Color Reproduction Adjustment ......................................
9. Max. Gain Adjustment .....................................................
10. Auto White Balance & LV Reference Data Acquisition ...
11. Auto White Balance Adjustment .....................................
12. Auto White Balance Check ..............................................

3-2. Operation during Adjustment ........................................ 6
3-2-1.
3-2-2.
3-2-3.
3-2-4.

How to Enter the Test Mode ........................................ 6
How to Exit from the Test Mode .................................. 6
Description of Test Mode Screen ................................ 6
Key Operation in Test Mode ........................................ 7

• Main Parts
The following parts can be supplied as main parts of the camera block in this set.
1) Camera Block (General Assembly including 2), 3) mentioned below and minor parts) .... (A-3250-920-A)
2) Zoom Lens (LSV-620B) ....................................................................................................... (8-848-732-01)
3) CCD Block Assembly ........................................................................................................... (A-3328-667-A)
* Further, there are small parts such as brackets and screws. See the Parts Price List.
* The Camera Process Board (VC-216 Board) alone is not supplied.
• Adjustment Items Required When Main Parts are Replaced
When the main parts were replaced, the adjustments marked with “z” in the following table are required.
Replacement Parts
Camera Block
Zoom Center Adjustment (Note 1)

Camera Block
(A-3250-920-A)

Zoom Lens (LSV-620B)
(8-848-732-01)

CCD Block Ass’y
(A-3328-667-A)

z

Hall Adjustment

z

Flange Back Adjustment

z

z (Note 2)

Optical Axis Adjustment

z

z

AGC Gain Calibration Adjustment

z

Color Reproduction Adjustment

z

Max Gain Adjustment

z

Auto White Balance &
LV Reference Data Acquisition

z

Auto White Balance Adjustment

z

Table 7-3-1
Note 1: Also, if the Zoom Switch Unit (1-418-202-21) was replaced, perform the Zoom Center Adjustment.
Note 2: Check the flange back, and if deviated, adjust it.

–2–

8
8
9
11
12
13
15
16
17
18
18
19

3-1.

Preparation before Adjustment

3-1-1. Service Tools List
• Oscilloscope
• Regulated Power Supply

• Color Monitor
• Digital Voltmeter

• Vectorscope

Ref. No.

Name

J-1

Filter for color temperature correction (C14)

J-6080-058-A

Auto white balance adj./check
White balance adj./check

ND filter 1.0

J-6080-808-A

White balance check
White balance check

J-2

Part Code

Usage

ND filter 0.3

J-6080-818-A

J-3

Pattern box PTB-450

J-6082-200-A

J-4

Color chart for pattern box

J-6020-250-A

J-5

Siemens star chart

J-6080-875-A

J-6

Clear chart for pattern box

J-6080-621-A

J-7

Mini pattern box

J-6082-353-B

Flange back adjustment

J-8

Camera base

J-6082-384-A

Flange back adjustment

J-1

J-2

J-3

J-6

J-7

J-8

Flange back check

J-4

Fig. 7-3-1

–3–

J-5

3-1-2.

Preparation
Pattern box

Note 1: See “DISASSEMBLY” for removing the cabinet and each
board.
Note 2: The lens block and each board need not be separated, if
only the adjustment is performed.
Note 3: For the power supply, use exclusive AC adapter.
about 1.5m

Front side of the lens

Fig. 7-3-2

–4–

3-1-3.

Precautions

1. Switch setting
Set the switches to the following positions respectively and perform the adjustment without loading a disc, unless otherwise specified.
1.
2.
3.
4.
5.
6.
7.
8.

POWER switch ...................................................... CAMERA
DIGITAL ZOOM (MENU screen) ........................ OFF
STEADY SHOT (MENU screen) ......................... OFF
FOCUS ................................................................... MANUAL
PROGRAM AE (MENU screen) ........................... AUTO
PICTURE EFFECT (MENU screen) .................... OFF
WHITE BALANCE (MENU screen) .................... AUTO
AUTO SHUTTER (MENU screen) ...................... OFF

2. Order of Adjustments
Basically carry out adjustments in the order given.
Color bar chart (Color reproduction adjustment frame)

Electronic beam scanning frame

C

C=D

D

Yellow
Cyan
Green
White
Magenta
Red
Blue

Blue

Yellow
Cyan
Green
White
Magenta
Red

H

CRT picture frame

V
A B

A=B

B A

Fig. b (monitor TV picture)

Enlargement

Fig. a
(VIDEO terminal of A/V jack
output waveform)

Difference in level

B

Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the monitor TV display shown in Fig. b.

A

Fig. 7-3-3
3. Subjects
1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 7-3-3. (Color reproduction
adjustment frame)
2) Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time)
3) Chart for flange back adjustment
Join together a piece of white A0 size paper (1189 mm × 841
mm) and a piece of black paper to make the chart shown in
Fig. 7-3-4.
Note: Use a non-reflecting and non-glazing vellum paper. The
size must be A0 or larger and the joint between the white
and black paper must not have any undulations.

–5–

White
841 mm
Black

1189 mm

Fig. 7-3-4

3-2. Operation during Adjustment
In adjusting the camera, execute the service mode in the Test Mode.
Note: For the adjustment items that must be checked with the color
monitor, first connect the VIDEO OUT to the monitor, and
then set the Test Mode.
(If connected later, no video signal will be outputted.)
3-2-1. How to Enter the Test Mode
In the normal mode, set the POWER switch to “CAMERA”.
While pressing u key on the set, press >, >, ., .,
e, E, e, E, y, y keys on the set in this order.
The Test Mode screen (Fig. 7-3-5) appears on the LCD and the
Test mode becomes active.

TEST MODE

2) Test mode item number display field
Major item number
Medium item number
Minor item number

made by MD dep.

I TRON
Drive
JAVA APP
JAVA OS
BOOT
I PL
RATE CTL
Item No.

1) Version display field
The versions of respective programs that compose the set are
displayed.
ITON ............ Version of set program
Drive ............. Version of drive program
JAVA APP ..... Version of JAVA application
JAVA OS ....... Date when JAVA OS was released
BOOT ........... Version of BOOT program
IPL ................ Version of IPL program
RATE CTL ... Version of V850 (IC8501 on Main board)
program

Ver.
Ver.
Ver.
Ver.
Ver.
Ver.
Ver.

Item No.

s. sss
s. sss
ssssssss
ssssssss
s. sss
s. sss
s. sss

1–02– 01
Fig. 7-3-7

Current Test mode item number is used.
The Test mode items are composed of a major item, medium
item, and minor item.
The number displayed in blue is currently active item.

1–00–00

Camera

3) Test mode item name display field
Medium
item name

Major item name

Fig. 7-3-5

Camera

3-2-2. How to Exit from the Test Mode
Turn the power off.
Note: In the Test mode, the POWER switch is inactive and therefore disconnect AC adapter to turn the power off.

Adjust

Service mode
Minor item name

Fig. 7-3-8
3-2-3.

Description of Test Mode Screen
Major item name, medium item name, and minor item name of
current test mode are displayed respectively.

TEST MODE

made by MD dep.

I TRON
Drive
JAVA APP
JAVA OS
BOOT
I PL
RATE CTL
Item No.

Ver.
Ver.
Ver.
Ver.
Ver.
Ver.
Ver.

4) Camera register display field

s. sss
s. sss
ssssssss
ssssssss
s. sss
s. sss
s. sss

Page
Address
Data

1–02–01

Camera

06–00–00

Adjust

Service mode

Cursor

06–00–00

Fig. 7-3-9
Camera register
display field
Test mode item name
Test mode item No. display field
display field
Version display field

The register state (page/address/data) in the camera block is displayed. Also, active item at present is underlined with a red cursor.

Fig. 7-3-6

–6–

3-2-4. Key Operation in Test Mode
In the Test mode, use the keys on the set for operation.
For adjusting the camera, execute the test mode item “1-02-01”
(major item: Camera, medium item: Adjust, and minor item: Service mode) to select the Service mode and perform adjustment
while writing data to the camera register.
1.

2.

Moves the cursor by . key

Change or setting of test mode item
• Movement over active item numbers (u, x keys)

06–00–00

x key Moveing

Item No.

Change or writing of camera register
(Operation in Service mode)
• Cursor movement (., > keys)

Moves the cursor by > key

1–02–01

Fig. 7-3-11

u key Moveing

Pressing the . key or > key causes the cursor to be
moved as shown above.
Note: If page is “01”, the cursor will stand still at the page
position.

Fig. 7-3-10
Use u key when setting active item number and moving
to lower level, or use x key when canceling current item
and moving to higher level.

• Page change (e, E keys)
When the cursor is in page position, pressing the e key increases the page, or the E key decreases the page. There are
15 pages, 01 to 0F.

• Change of active item number (> . keys)
Use > key to raise active item number, or . key to
lower it.

• Address change (e, E keys)
When the cursor is in address position, pressing the e key
increases the address, or the E key decreases the address.
Also, pressing the u key increases the higher order digit
of 00-FF.
There are 256 addresses, 00 to FF.

• Execution or cancellation of item (u, x keys)
If the test mode item “1-02-01” (major item: Camera, medium item: Adjust, and minor item: Service mode) was set,
pressing the u key causes the register state to be displayed
in the cameral register display field, and the Service mode
to be active. To cancel this item, press the x key.

• Data change (e, E keys)
When the cursor is in data position, pressing the e key increases the data, or the E key decreases the data.
Also, pressing the u key increases the higher order digit
of 00-FF.
There are 256 data, 00 to FF.
• Data writing (y key)
To write data to the nonvolatile memory, press the y key.
(Unless this operation is performed, new data are not stored
in the nonvolatile memory.)
3. Switching of screen display
The camera adjustment contains the items to be adjusted with the
camera-through screen.
• Camera-through screen display method (DSPL key)
Press the DSPL key, and the screen display will be switched
as shown below.

Test mode screen

10-step gradation pattern screen
(Camera-through screen, if not set in “EVF” item)

Camera-through screen

–7–

3-3.

Camera System Adjustment

1. Zoom Center Adjustment
Adjust the center voltage of Zoom control to the center of microcomputer A/D value.
If deviated, zooming will be executed even with the Zoom control in center position.
Subject

Arbitrary

Measurement point

Display data of page: 06, address: 50

Adjustment page

0F

Adjustment address

5D

Note: Do not touch the Zoom lever during adjustment.
(The Zoom lever must be in center position.)
Adjusting method
Page

Address

1

06

50

2

0F

5D

Steps

Data

Work Description
Read the displayed data (D50).

D50

Set the data read in step 1, and press the y key.

2. Hall Adjustment
To detect the lens iris position, adjust the gain and offset of the amplifier.
If deviated, the iris will oscillate or the white balance between indoor and outdoor will be disordered.
Subject

Arbitrary

Adjustment page

0F

Adjustment address

1E, 1F, 70

Note: For the data display, the data at the time when address was set is displayed, and it is not updated.
Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Adjusting method
Page

Address

1

06

02

2

06

94

8A

Press the y key.

3

06

95

17

Press the y key.

4

06

01

6D

Press the y key.
(Hall is adjusted, and the data are automatically entered to page: F, address: 1E, 1F, 70.)

5

06

02

6

06

01

Steps

Data

Work Description
Check that the data is “00”.

Check that the data becomes “01”. (Note)
00

Press the y key.

Processing after completion of adjustment
Page

Address

Data

1

06

01

00

Press the y key.

2

06

94

00

Press the y key.

3

06

95

00

Press the y key.

Steps

Work Description

–8–

3. Flange Back Adjustment (Using flange back adjusting chart subject more than 500 m away)
The flange back adjustment of the inner focus lens is carried out automatically.
If deviated, auto focus and manual focus will be disordered.
Flange back adjustment (1)
Subject

Flange back adjusting chart
(Located at 2.00 m position from lens front surface)
(Luminance: 350 (50 lux)

Measurement point

Check operation on monitor TV

Measuring instrument

(Camera-through screen)

Adjustment page

0F

Adjustment address

24 – 29, 36 – 3D

Note: For the data display, the data at the time when address was set is displayed, and it is not updated.
Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Adjusting method
Steps

Page

Address

Data

Work Description
With the zoom lens at TELE end and WIDE end respectively, check that the center of the
shot image screen concurs with the center of flange back adjusting chart.

1
2

06

02

Check that the data is “00”.

3

06

01

13

Press the y key.

4

06

01

15

Press the y key.
(The flange back adjustment is carried out, and the data are automatically entered to
page: F, address: 24 – 29 and 36 – 3D.)

5

06

02

Check that the data becomes “01”. (Note)

Processing after completion of adjustment
Steps
1
2

Page

Address

Data

06

01

00

Work Description
Press the y key.
Perform “Flange back adjustment (2)”.

–9–

Flange back adjustment (2)
Subject

Subject more than 500 m away
(which should be clear contrast such as a building)

Measurement point

Check operation on monitor TV

Measuring instrument

(Camera-through screen)

Adjustment page

0F

Adjustment address

24 – 29, 36 – 3D

Note: For the data display, the data at the time when address was set is displayed, and it is not updated.
Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Adjusting method
Steps

Page

Address

Data

Work Description
With the zoom lens at TELE end, shoot the subject distant over 500 m (such as a building
having clear contrast).
(At this time, the subjects distant below 500 m must not be displayed on the screen.)

1
2

06

02

3

06

01

Check that the data is “00”.
13

4

Press the y key.
Cover the lens with ND filter, and adjust so as to get the optimum image.

5

06

01

6

06

02

29

Press the y key.
(The flange back adjustment is carried out, and the data are automatically entered to
page: F, address: 24 – 29 and 36 – 3D.)
Check that the data becomes “01”. (Note)

Processing after completion of adjustment
Steps
1
2

Page

Address

Data

06

01

00

Work Description
Press the y key.
Perform “Flange Back Check”.

– 10 –

4. Flange Back Adjustment (Using mini pattern box)
The flange back adjustment of the inner focus lens is carried out automatically.
If deviated, auto focus and manual focus will be disordered.
Subject

Mini pattern box with ND filter
Siemens star chart (Note 1)

Measurement point

Check operation on monitor TV

Measuring instrument

(Camera-through screen)

Adjustment page

0F

Adjustment address

24 – 29, 36 – 3D

Note 1: Darker Siemens star chart
Note 2: The mini pattern box is used for the flange back adjustment only.
For other adjustments, use the pattern box (PTB-450).
Note 3: For the data display, the data at the time when address was set is displayed, and it is not updated.
Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Preparation for adjustment
Install the mini pattern box as shown below.
Note 4: The attachment is not used.

Within 3 cm
Mini pattern box
Set

Specified voltage: Variable depending on the mini pattern box.
Therefore, set the voltage given on the sheet
attached to the mini pattern box.

Camera
base
Regulated power supply
Specified voltage ( 0.01 Vdc)
Output current over 3.5 A

Red (+)
Black (–)
Yellow (SENS +)
White (SENS –)

No connection

Black (GND)

Fig. 7-3-12
Adjusting method
Steps

Page

Address

Data

Work Description

1

Install the mini pattern box so that it is located within 3 cm from the lens front surface.

2

Adjust the height of mini pattern box.

3

Check that the output voltage of regulated power supply is the specified voltage
± 0.01 Vdc.

4

With the zoom lens at TELE end and WIDE end respectively, check that the center of the
shot image screen concurs with the center of Siemens star frame.

5

06

02

6

06

01

13

Check that the data is “00”.
Press the y key.

7

06

01

27

Press the y key.
(The flange back adjustment is carried out, and the data are automatically entered to
page: F, address: 24 – 29 and 36 – 3D.)

8

06

02

Check that the data becomes “01”. (Note 3)

Processing after completion of adjustment
Steps
1
2

Page

Address

Data

06

01

00

Work Description
Press the y key.
Perform “Flange Back Check”.

– 11 –

5. Flange Back Check
Subject

Siemens star (reflection type)
(Located at 2.00 m position from lens front surface)
(Luminance: about 200 lux)

Measurement point

Check on monitor TV

Measuring instrument

(Camera-through screen)

Adjustment value

Focus must be in order at TELE end and WIDE end

Switch setting
1) DIGITAL ZOOM (Menu screen) ....... OFF
2) STEADY SHOT (Menu screen) ......... OFF
3) FOCUS ................................................ AUTO
Note: When Auto Focus is ON, whether the focus is in order or disordered can be judged from the data displayed on page 01.
1) Select page: 06, address: 04, and set data: 0F, then press the y key.
2) The focusing condition can be confirmed from the data displayed on page 01.
01-00-XX
Odd number : Focus is in order.
Even number: Focus is disordered.
Checking method
Steps

Page

Address

Data

Work Description

1

Place the Siemens star at 2.0 m forward position from the lens front surface. As the iris is
in open state, lower the luminance of Siemens star to the extent that noise does not appear
on the monitor TV.

2

Shoot the Siemens star with the zoom at TELE end.

3

Check that the focus is in order. (Note)

4

06

21

10

Press the y key.

5

Shoot the Siemens star with the zoom at WIDE end.

6

Check on the monitor screen that the focus is in order.

Processing after completion of check
Page

Address

Data

1

06

21

00

Press the y key.

2

06

04

00

Press the y key.

Steps

Work Description

– 12 –

6. Optical Axis Adjustment
Correct the deviation of optical axis between lens and CCD imager.
If deviated, the center of screen will be shifted when the zoom is moved from TELE end to WIDE end.
Subject

Siemens star (reflection type)

Measurement point

Check on monitor TV

Measuring instrument

(Camera-through screen)

Adjustment page

0F

Adjustment address

43

Switch setting
1) DIGITAL ZOOM (Menu screen) ....... OFF
2) STEADY SHOT (Menu screen) ......... OFF
Preparation for adjustment:
Stick the optical axis deviation specification frame to the monitor screen. At this time, make the monitor center and the specification frame
center concurrent.

0
337.5

22.5

8
1

7
292.5

270

67.5

6

2

247.5

90

112.5

3

5
4
202.5

157.5

180
Fig. 7-3-13

– 13 –

Adjusting method
Page

Address

Data

06

40

02

Press the y key.

2

06

41

01

Press the y key.

3

0F

43

00

Press the y key.

Steps
1

Work Description

4

Place the Siemens star at 2.0 m forward position from the lens front surface.

5

Shoot the Siemens star with the zoom at TELE end.

6

Adjusting the lens direction, make the center of Siemens star and the center of optical axis
deviation specification frame (monitor screen) concurrent.

7

Shoot the Siemens star with the zoom at WIDE end.

8

On the monitor TV, check which area of the optical axis deviation specification frame the
center of Siemens star enters.
At this time, measure the center deviation “L1” (distance between center of Siemens star
and center of optical axis deviation specification frame).
Read correction data (D43) according to the area in the following table.
Area

Deviation phase

Correction data

1

22.6° – 67.5°

01

2

67.6° – 112.5°

02

3

112.6° – 157.5°

03

4

157.6° – 202.5°

04

5

202.6° – 247.5°

05

6

247.6° – 292.5°

06

7

292.6° – 337.5°

07

8

337.6° – 22.5°

08

9

10

0F

43

D43

Set the read correction data, and press the y key.

11

Shoot the Siemens star with the zoom at TELE end.

12

Adjusting the lens direction, make the center of Siemens star and the center of optical axis
deviation specification frame concurrent.

13

Shoot the Siemens star with the zoom at WIDE end.

14

Measure the center deviation “L2” (distance between center of Siemens star and center of
optical axis deviation specification frame).

15

0F

Compare L1 and L2 to make sure that L2 is smaller than L1.
If larger, set data: 00 and press the y key.

43

Processing after completion of adjustment
Page

Address

Data

1

06

40

00

Press the y key.

2

06

41

00

Press the y key.

Steps

Work Description

– 14 –

7.

AGC Gain Calibration Adjustment

Subject

Clear chart (PTB-450)
(Color reproduction adjusting frame)

Adjustment page

0E

Adjustment address

3A – 3D

Note: For the data display, the data at the time when address was set is displayed, and it is not updated.
Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Switch setting
1) DIGITAL ZOOM (Menu screen) ....... OFF
2) STEADY SHOT (Menu screen) ......... OFF
Adjusting method
Steps

Page

Address

Data

Work Description

1

06

02

2

0F

6E

08

Check that the data is “00”.
Press the y key.

3

06

01

71

Press the y key.
(The AGC gain calibration adjustment is carried out, and the data are automatically
entered to page: E, address: 3A – 3D.)

4

06

02

Check that the data becomes “01”. (Note)

Processing after completion of adjustment
Page

Address

Data

1

0F

6E

FF

Press the y key.

2

06

01

00

Press the y key.

Steps

Work Description

– 15 –

8 Color Reproduction Adjustment
Adjust the primary color separation matrix factor so that colors are reproduced correctly.
If deviated, colors are not reproduced correctly.
Subject

Color bar chart (PTB-450)
(Color reproduction adjusting frame)

Measuring point

VIDEO terminal of VIDEO/AUDIO terminals
(Camera-through screen)

Measuring instrument

Vectorscope

Adjustment page

0F

Adjustment address

2E, 30, 44, 45

Adjustment value

All color luminance points must fall in respective
color reproduction frame

Adjusting method
Page

Address

Data

06

00

01

Press the y key.

2

06

01

3D

Press the y key.

3

0F

16

37

Press the y key.

Steps
1

Adjusting the GAIN and PHASE of the vectorscope, adjust the burst luminance point to
the burst position of the color reproduction adjusting frame.

4
5

0F

5E

29

2E
6

Work Description

0F

30

Press the y key.
Change the data so that each color luminance point falls within each color reproducible
area.
Note: Each time the data is changed, press the y key.
Unless this key is pressed, new data is not written.

44
45

Processing after completion of adjustment
Page

Address

Data

1

0F

5E

2E

Press the y key.

2

0F

16

33

Press the y key.

3

06

00

00

Press the y key.

4

06

01

00

Press the y key.

Steps

Work Description

R-Y

R

MG

YE
B-Y
B

CY
G
Burst position

Fig. 7-3-14

– 16 –

9. Max. Gain Adjustment
Set the lowest subject illuminance.
If deviated, necessary video level will not be got in low illuminance environment.
Clear chart (PTB-450)
(Color reproduction adjusting frame)

Subject
Adjustment page

0F

Adjustment address

2C

Note: For the data display, the data at the time when address was set is displayed, and it is not updated.
Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Switch setting
1) STEADY SHOT (Menu screen) ......... OFF
Adjusting method
Page

Address

1

06

02

2

06

96

00

Press the y key.

3

06

97

27

Press the y key.

4

06

01

6F

Press the y key.
(The max. gain adjustment is carried out, and the data is automatically entered to
page: F, address: 2C.)

5

06

02

Steps

Data

Work Description
Check that the data is “00”.

Check that the data becomes “01”. (Note)
It may take much time (several sec to ten and several sec).

Processing after completion of adjustment
Page

Address

Data

1

06

96

00

Press the y key.

2

06

97

00

Press the y key.

3

06

01

00

Press the y key.

Steps

Work Description

– 17 –

10. Auto White Balance & LV Reference Data Acquisition
Clear chart (PTB-450)
(Color reproduction adjusting frame)

Subject
Adjustment page

0F

Adjustment address

20 – 23, 3E, 3F

Note 1: Color Reproduction Adjustment must be already finished.
Note 2: The auto white balance & LV reference data acquisition is available only once after the power is turned on. Turn the power off,
then on again if the data acquisition is retried.
Note 3: For the data display, the data at the time when address was set is displayed, and it is not updated.
Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Adjusting method
Page

Address

1

06

02

2

06

01

Steps

3

06

01

4

06

02

Data

Work Description
Check that the data is “00”.

11

Press the y key.

0D

Press the y key.
(The auto white balance & LV reference data acquisition is carried out, and the data are
automatically entered to page: F, address: 20 – 23, 3E, 3F.)
Check that the data becomes “01”. (Note 3)

Processing after completion of adjustment
Steps
1

Page

Address

Data

06

01

00

2

Work Description
Press the y key.
Perform “Auto White Balance Adjustment”.

11. Auto White Balance Adjustment
Adjust auto white balance so that correct data are outputted.
If deviated, color reproduction in the auto white balance mode will be reduced.
Subject

Clear chart (PTB-450)
(Color reproduction adjusting frame)

Filter

Color temperature correction filter C14

Measurement point

Displayed data on page: 01

Adjustment page

0F

Adjustment address

34, 35

Note 1: “Auto White Balance & LV Reference Data Acquisition” must be already finished.
Note 2: The auto white balance adjustment is available only once after the power is turned on. Turn the power off, then on again if the
adjustment is retried.
Note 3: For the data display, the data at the time when address was set is displayed, and it is not updated.
Check data variation while repeating address change and resetting (change address from “02” to “01”, and then return it to “02”).
Adjusting method
Steps

Page

Address

Data

1

Work Description
Cover the lens with the color temperature correction filter C14.

2

06

02

3

06

01

83

Check that the data is “00”.
Press the y key.

4

06

01

81

Press the y key.
(The auto white balance adjustment is carried out, and the data are automatically entered
to page: F, address: 34, 35.)

5

06

02

Check that the data becomes “01”. (Note 3)

Processing after completion of adjustment
Steps
1

Page

Address

Data

06

01

00

Work Description
Press the y key.

– 18 –

12.

Auto White Balance Check

Subject

Clear chart (PTB-450)
(Color reproduction adjusting frame)

Filter

Color temperature correction filter C14
ND filter 1.0 and 0.3

Measurement point

VIDEO terminal of VIDEO/AUDIO terminals
(Camera-through screen)

Measuring instrument

Vectorscope

Adjustment value

Fig. 7-3-15 (A) – (C)

Checking method
Steps

Page

Address

Data

06

01

0F

06

01

23

1
2

Check that the lens is not covered with any filter.

3
4

Work Description
Press the y key.
Check that the center of white luminance point is within a circle shown in Fig. 7-3-15 (A).
Press the y key.

5

Cover the lens with C14 filter.

6

Check that the center of white luminance point falls within a circle shown in Fig. 7-3-15 (B).

7

Remove the C14 filter, and cover the lens with ND filter 1.3 (1.0 + 0.3).

8

After making sure that the white luminance point pull-in motion finished, remove the ND
filter 1.3.

9

Check that the center of white luminance point falls within a circle shown in Fig. 7-3-15 (C).

Processing after completion of check
Steps
1

Page

Address

Data

06

01

00

Work Description
Press the y key.

R-Y

R-Y
R-Y

3 mm

1 mm

B-Y

B-Y
2 mm

3 mm

3 mm

0.5 mm

2 mm
B-Y

2 mm

3 mm
1 mm

Fig. 7-3-15 (A)

Fig. 7-3-15 (B)

– 19 –

Fig. 7-3-15 (C)

• Correction of Schematic Diagrams

! : Indicates changed portion.

MAIN BOARD (4/8) (Page 4-44. Location B to C, 14 to 16)
Incorrect

Correct

^

^

MAIN BOARD (5/8) (Page 4-52. Location A to B, 37 to 39)
Incorrect

^

Correct

^

^

^

MAIN BOARD (6/8) (Page 4-53. Location A to E, 5 to 8)
Incorrect

Correct

#

#

%

%

– 20 –

VF BOARD (2/3) (Page 4-90. Location I to J, 30 to 32)
Incorrect

Correct

% ^

%

^

ETHER BOARD (Page 4-117. Location B to D, 6 to 9)
Incorrect

Correct

%
#

%
#

– 21 –

FOR CAMERA OPTICAL AXIS ADJUSTMENT

0
337.5

22.5

8
1

7
292.5

6

2

247.5

90

112.5

3

5
4
202.5

157.5

180

– 22 –

✄

270

67.5

FOR CAMERA COLOR REPRODUCTION ADJUSTMENT
Take a copy of CAMERA COLOR
REPRODUCTION FRAME with a
clear sheet for use.

R-Y

R

MG

YE
B-Y
B

CY
G

✄

✄

DCM-M1

– 23 –

CDM-M1

Sony Corporation
9-927-635-83

Audio Entertainment Group

2000H05035-1
Printed in Japan C 2000. 8
Published by General Engineering Dept.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2000:01:08 14:14:22
Producer                        : Acrobat Distiller 4.0 for Macintosh
Modify Date                     : 2000:08:08 11:49:27+09:00
Title                           : DCM-M1
Subject                         : US/Canadian/E
Author                          : Sony Corporation
Page Count                      : 198
Page Mode                       : UseThumbs
EXIF Metadata provided by EXIF.tools

Navigation menu