HCD MD333 Sony_HCD MD333_service_manual Sony Service Manual
User Manual: sony_HCD-MD333_service_manual
Open the PDF directly: View PDF 
.
Page Count: 92
| Download | |
| Open PDF In Browser | View PDF |
HCD-MD333 SERVICE MANUAL US Model Canadian Model AEP Model UK Model E Model Australian Model Tourist Model Ver 1.1 2001. 06 HCD-MD333 is the amplifier, CD, MD and tuner section in DHC-MD333. CD SECTION MD SECTION Model Name Using Similar Mechanism NEW Mechanism Type CDM13C-5BD19 Base Unit Type BU-5BD19 Optical Pick-up Type KSS-213B/K-N Model Name Using Similar Mechanism NEW Mechanism Type MDM-3J Optical Pick-up Type KSM-260A-JIN SPECIFICATIONS — Continued on next page — COMPACT DISC DECK RECEIVER 9-922-935-12 Sony Corporation 2001F0200-1 © 2001.6 Home Audio Company Shinagawa Tec Service Manual Production Group –1– –2– SELF-DIAGNOSIS FUNCTION The self-diagnosis function consists of error codes for users which are displayed automatically when errors occur, and error codes which show the error history in the test mode during servicing. For details on how to view error codes for users, refer to the following box in the instruction manual. For details on how to perform checks during servicing, refer to the following “Procedure for Using the Self-Diagnosis Function (Error History Display Mode)”. Procedure for Using the Self-Diagnosis Function (Error History Display Mode) Note: Perform the self-diagnosis function in the “error history display mode” in the test mode. The following describes the least required steps. Be careful not to enter other modes by mistake. If other modes are set accidentally, press the ^ (CD) button to exit that mode. 1. 2. 3. 4. 5. 6. 7. 8. With the power off, press the ^ (MD) button while pressing the PLAY MODE button. Rotate the VOLUME knob until “ERR DP MODE” is displayed. Pressing the p (CD) button sets the error history mode and displays “total rec”. Select the contents to be displayed or executed using the VOLUME knob. Pressing the 6 (CD) button displays or executes the contents selected. Pressing the 6 (CD) button another time returns to step 4. Pressing the ^ (CD) button displays “ERR DP MODE” and exits the error history mode. To exit the test mode, press the REPEAT button. The unit sets into the STANDBY state, and the test mode ends. –3– ITEMS OF ERROR HISTORY MODE ITEMS AND CONTENTS Selecting the Test Mode Display Details of History total rec Displays the recording time in the form of “rππππππh”. The displayed time is the total number of hours the laser is high power, which is about one-fourth of the actual recording time. The time is displayed in decimal digits between 0h to 65535h. total play Displays the playback time in the form of “pππππππh”. The displayed time is the total actual play time. The paused time is not counted. The time is displayed in decimal digits between 0h to 65535h. retry err Displays the total number of retries during recording and retry errors during playback in the form of “rππpππ”. “r” indicates the retries during recording while “p” indicates the retry errors during playback. The number of retries is displayed in hexadecimal digits between 00 to FF. total err Displays the total number of errors in the form of “total ππ”. The number of errors is displayed in hexadecimal digits between 00 to FF. err history Displays the 10 latest errors in the form of “0π E@@”. The π indicates the history number. The smaller the number, the newer is the error. (00 is the latest error.) The @@ indicates the error code. Refer to the following table for details. Rotate the VOLUME knob to switch the error history. er refresh? Mode which erases all the error histories. The error history serves as a reference for when to replace the optical pick-up. Perform this procedure when the optical pick-up has been replaced in order to erase past error histories and not at other times. Press the p (CD) button when “er refresh??” is displayed. The history will be erased and “Complete!” will be displayed momentarily. Be sure to check the following when this mode has been executed. • Check that the data has been erased. • Perform recording and playback, and check that the mechanism operates normally. Table of Error Codes Error Code E00 No error E05 Details of Error FOK has deviated E01 Disc error. Cannot read PTOC E06 Unfocused (Servo has deviated) (Disc is ejected out) E07 Recording retry Disc error. UTOC error E08 Recording retry error (Disc is not ejected out) E09 Play retry error E02 Details of Error E03 Loading error E04 Cannot read address (Servo has deviated) Error Code (Access error) E0A –4– Playback retry error (C2 error) MODEL IDENTIFICATION — BACK PANEL — Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. This caution label is located inside the unit. MODEL AEP, UK, EE model MY, SP, JE, HK, AR, AUS model US, CND model PARTS No. 4-993-849-5π 4-993-849-6π 4-993-849-7π • Abbreviation CND : Canadian model EE : East European model HK : Hong Kong model SP : Singapore model MY : Malaysia model AR : Argentine model AUS : Australian model JE : Tourist model CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing • Keep the temperature of soldering iron around 270˚C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. SAFETY-RELATED COMPONENT WARNING !! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. –5– SAFETY CHECK-OUT TABLE OF CONTENTS After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. 1. SERVICING NOTE .......................................................... 7 LEAKAGE The AC leakage from any exposed metal part to earth Ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A) 3-1. Case .................................................................................... 10 3-2. Front Panel/MD Mechanism Deck Section ........................ 10 3-3. Back Panel, Jack Board ....................................................... 11 3-4. MD Mechanism Deck (MDM-3D) ..................................... 11 3-5. CD Mechanism Deck (CDM13C-5BD19).......................... 12 3-6. BD (MD) Board .................................................................. 12 3-7. Disc Table .......................................................................... 13 3-8. Sub Chassis ......................................................................... 13 3-9. Optical Pick-up (KSS-213B/K-N) ...................................... 14 3-10. Over Write Head ............................................................... 14 3-11. Slider Complete ASSY ...................................................... 15 3-12. Shutter ASSY .................................................................... 16 2. GENERAL .......................................................................... 8 3. DISASSEMBLY 4. SERVICE MODE ............................................................. 17 5. TEST MODE ..................................................................... 18 6. ELECTRICAL ADJUSTMENTS ............................... 24 To Exposed Metal Parts on Set 0.15µF 1.5kΩ 7. DIAGRAMS AC voltmeter (0.75V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. 7-1. Circuit Boards Location ...................................................... 31 7-2. Block Diagrams • CD Section ....................................................................... 33 • MD Section ...................................................................... 35 • Main Section .................................................................... 37 7-3. Schematic Diagram – CD Section – ................................... 41 7-4. Printed Wiring Board – CD Section – ................................. 43 7-5. Schematic Diagram – MD (1/3) Section – .......................... 45 7-6. Schematic Diagram – MD (2/3) Section – .......................... 47 7-7. Schematic Diagram – MD (3/3) Section – .......................... 49 7-8. Printed Wiring Board – MD Section – ................................ 51 7-9. Schematic Diagram – MD Switch Section – ...................... 53 7-10. Printed Wiring Board – MD Switch Section – ................. 54 7-11. Schematic Diagram – Main (1/3) Section – ..................... 55 7-12. Schematic Diagram – Main (2/3), (3/3) Section – ........... 57 7-13 Printed Wiring Board – Main Section – ........................... 59 7-14. Schematic Diagram – Audio Section – ............................. 61 7-15. Printed Wiring Board – Audio Section – .......................... 63 7-16. Schematic Diagram – Panel Section – ............................. 65 7-17. Printed Wiring Board – Panel Section – ........................... 67 7-18. Schematic Diagram – Jack Section – ............................... 69 7-19. Printed Wiring Board – Jack Section – ............................ 71 7-20. Schematic Diagram – ST Terminal/Loading Section – .... 73 7-21. Printed Wiring Board – ST Terminal/Loading Section – . 74 7-22. Schematic Diagram – Trans Section – ............................. 75 7-23. Printed Wiring Board – Trans Section – ........................... 76 7-24. Schematic Diagram – Power AMP Section – ................... 77 7-25. Printed Wiring Board – Power AMP Section – ................ 79 7-26. IC Block Diagrams ........................................................... 81 7-27. IC Pin Functions ............................................................... 88 8. EXPLODED VIEWS 8-1. 8-2. 8-3. 8-4. 8-5. 8-6. Front Panel Section ............................................................. 96 Chassis Section ................................................................... 97 MD Mechanism Deck Section-1 (MDM-3J) ...................... 98 MD Mechanism Deck Section-2 (MDM-3J) ...................... 99 CD Mechanism Deck Section-1 (CDM13C-5BD19) ....... 100 CD Mechanism Deck Section-2 (BU-5BD19) ................. 100 9. ELECTRICAL PARTS LIST ...................................... 102 –6– SECTION 1 SERVICING NOTE DISC TABLE GETTING OUT PROCEDURE ON THE POWER SUPPLY IS OFF NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. 1. Insert the tweezers to a hole on bottom of the chassis as shown a figure, then tern fully it toward direction 2. 2. Pull out the disc table. cam NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. disc table LASER DIODE AND FOCUS SEARCH OPERATION CHECK 3 Carry out the “S curve check” in “CD section adjustment” and check that the S curve waveform is output three times. 2 Note: Be sure to connect all wires (including FFC) in the MD section before applying power or ICs may be damaged. 1 tweezers PRECAUTIONS ON REMOVING WINDOW (FL) FROM FRONT PANEL • Use the following procedure to prevent scratches on the front panel. 3 Remove the ornament (VOL). 4 Remove the window (FL) using the notch. 2 Remove the nut. 1 Remove the Knob (VOL). –7– SECTION 2 GENERAL Front Panel 1 2 3 4 5 6 23 22 7 8 9 10 21 20 19 18 17 Location of Parts and Controls 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 1/u button MD indicator MD disc slot 6 (MD) button ^ (MD) button and indicator p (MD) button VOLUME knob ^ (CD) button and indicator p (CD) button FUNCTION button MD/CD ) +/TUNING + button MD/CD = 0/TUNING – button TUNER/BAND button 6 (CD) button r REC button and indicator CD-MD SYNC button CD disc tray CD indicator REPEAT/STEREO/MONO button PLAY MODE/TUNING MODE button PHONES jack Remote sensor Display window –8– 16 15 14 13 12 11 This section is extracted from instruction manual. –9– SECTION 3 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 3-1. CASE 3 Case 1 Two screws (CASE3 TP2) 2 Two screws (CASE3 TP2) 3-2. FRONT PANEL/MD MECHANISM DECK SECTION 7 Six screws (BVTT3x6) 8 Wire 9 MD mechanism 3 Connector (CN490) 5 Front panel 4 Claw 2 Wire (flat type)(23core) (CN873) 1 Two screws (BVTT3x6) – 10 – 6 Wire (flat type)(25core) (CN820) 3-3. BACK PANEL, JACK BOARD 2 Four screws (BVTP3x10) 7 JACK board 6 Wire (flat type)(15core) (CN401) 3 Two screws (BVTP3x10) 8 Connector (CN402) 1 Connector (CN590) 5 Back panel 4 Five claws 3-4. MD MECHANISM DECK (MDM-3D) 1 Two screws (BVTT2x3) Bracket (MD) 2 Two screws (BVTT2x3) 3 MD mechanism deck (MDM-3J) – 11 – 3-5. CD MECHANISM DECK (CDM13C-5BD19) 4 Two screws (BVTT3x6) 8 CD mechanism deck (CDM13C-5BD19) 5 Bracket (CD) 6 Two screws (BVTT3x6) 7 Two hooks 3 Two screws (BVTT3x6) 2 Connector (CN291) 1 Wire (flat type)(19core) (CN801) 3-6. BD (MD) BOARD 3 Wire (flat type)(14core) (CN106) 5 OP relay flexible board (CN101) 2 Flexible board (over write head) (CN104) 1 Wire (flat type)(25core) (CN107) 6 BD board(MD) 4 Screw (BVTP2x4) – 12 – 3-7. DISC TABLE 3 Holder (MG) assembly 1 Screw (BV3x8) 2 Screw (BV3x8) 4 Pull the disc table 3-8. SUB CHASSIS 1 Two step screws 3 Two step screws 2 Two insulators 4 Two insulators Part A Part A Part A 5 Sub chassis Take care so that the part A may be right position when installing. – 13 – 3-9. OPTICAL PICK-UP (KSS-213B/K-N) 4 Remove the optical pick-up (KSS-213B/K-N) in the direction of the arrow C. C 3 Wire (flat type)(16 core) (CNU101) 1 Move the claw in the direction of the arrow A. B A 2 Remove the sled shaft in the direction of the arrow B. BD board (CD) 3-10. OVER WRITE HEAD 1 Screw (P1.7x6) 2 Over write head – 14 – 3-11. SLIDER COMPLETE ASSY 3 Set the shaft of gear (LB) to be at the position in the figure. Claw Claw 45˚ 4 Remove the slider complete assembly in the direction of arrow with putting out of two claws. 1 Special screw (M1.7x1.4) 2 Retainer (gear) • Note for installation of Slider complete assembly Slider assembly Install the part A of lever (head up) to pass over the slider complete assembly. OK Part A NG Take care not to damage the detective switch. – 15 – 3-12. SHUTTER ASSY 1 Stopper washer shutter assembly 2 Shaft (shutter) A Shaft (shutter) B 3 Shutter assembly Hole B Shaft (shutter) A Hole A When installing, install the shaft (shutter) A into the hole as show in the figure before installing the shaft (shutter) B into the hole B. – 16 – SECTION 4 SERVICE MODE Change-over of AM (MW) Tuner Step between 9 kHz and 10 kHz • A step of AM (MW) channels can be changed over between 9 kHz and 10 kHz. Procedure: 1. Press 1/u button to turn the set ON. 2. Select the function “TUNER”, and press TUNER/BAND button to select the BAND “AM (MW)”. 3. Press 1/u button to turn the set OFF. 4. Press FUNCTION and 1/u buttons simultaneously, and the display of fluorescent indicator tube changes to “AM (MW) 9 kHz STEP” or “AM (MW) 10 kHz STEP”, and thus the channel step is changed over. Change-over of LW Tuner Step between 1 kHz and 3 kHz • A step of LW channels can be changed over between 1 kHz and 3 kHz. Procedure: 1. Press 1/u button to turn the set ON. 2. Select the function “TUNER”, and press TUNER/BAND button to select the BAND “LW”. 3. Press 1/u button to turn the set OFF. 4. Press FUNCTION and 1/u buttons simultaneously, and the display of fluorescent indicator tube changes to “LW 1 kHz STEP” or “LW 3 kHz STEP”, and thus the channel step is changed over. LED and Fluorescent Indicator Tube All Lit, Key Check Mode Procedure: 1. Press PLAY MODE and p (MD) buttons simultaneously. 2. LEDs and fluorescent indiator tube are all turned on. 3. When the FUNCTION button is pressed, the fluorescent indicator tube lights up in the order of; partial lighting 1 n partial lighting 2 n all lit n partial lighting 1 n ······. When the VOLUME knob is rotated, the LED lighting pattern changes. To end without switching to the key check mode, press the 1/u button to turn off the power. 4. Press p (CD) button, and the key check mode is activated. 5. In the key check mode, the fluorescent indicator tube displays “KEY=0 JOG=0”. Each time a button is pressed, “KEY=” value increases. However, once a button is pressed, it is no longer taken into account. “JOG=” Value increases like 1, 2, 3 ... if rotating VOLUME knob in clockwise direction, or it decreases like 10, 9, 8 ... if rotating in counterclockwise direction. 6. To exit from this mode, press order all buttons (15 buttons), the displays “KEY=OK”, and press any button, or disconnect the power cord. SUB CLOCK CHECK Procedure: 1. Connect an oscilloscope to IC601 pin (¡ and ground of the MAIN board. 2. Press PLAY MODE and p (MD) buttons simultaneously, and the fluorescent indiator tube displays “32.768 kHz (91)”. 3. To check the signal on oscilloscope becomes 32 kHz square wave. 4. Press 1/u button to exit. – 17 – SECTION 5 TEST MODE 5-1. PRECAUTIONS FOR USE OF TEST MODE Recording Laser Emission Mode and Operating Buttons • Continuous recording mode (CREC MODE) • Traverse adjustment mode (EFBAL ADJUST) • Laser power adjustment mode (LDPWR ADJUST) • Laser power check mode (LDPWR CHECK) • Traverse (MO) check (EF MO CHECK) • Traverse (MO) adjustment (EF MO ADJUST) 5-2. SETTING THE TEST MODE With the power off, press the ^ (MD) button while pressing the PLAY MODE button. 5-3. EXITING THE TEST MODE Press the REPEAT button. The STANDBY state will be set and the test mode will be cleared. 5-4. BASIC OPERATIONS OF THE TEST MODE All operations are performed using the VOLUME knob, p (CD) button, and ^ (CD) button. The functions of these buttons are as follows. Function name Function VOLUME knob Changes parameters and modes p (CD) button Proceeds onto the next step. Finalizes input. ^ (CD) button Returns to previous step. Stops operations. – 18 – 5-5. SELECTING THE TEST MODE There are altogether 26 test modes, shown in the following table. Rotating the VOLUME knob to the right switches to the mode below the current mode in the table while rotating to the left switches to the mode above. Each time the ^ (CD) button is pressed, the display changes in the following order; “TEMP CHECK” n ”TEMP ADJUST” n ”SLED MOVE” n“TEMP CHECK”… Contents Display Mark TEMP CHECK Temperature compensation offset check LDPWR CHECK Laser power check EF MO CHECK Traverse (MO) check EF CD CHECK Traverse (CD) check FBIAS CHECK Focus bias check CPLAY MODE Continuous playback mode CREC MODE Continuous recording mode Scurve CHECK S curve check (X) VERIFY MODE Non-volatile memory check (X) DETRK CHECK Detrack check (X) TEMP ADJUST Temperature compensation offset adjustment LDPWR ADJUST Laser power adjustment EF MO ADJUST Traverse (MO) adjustment EF CD ADJUST Traverse (CD) adjustment FBIAS ADJUST Focus bias adjustment EEP MODE Nonvolatile memory control MANUAL CMD Command transfer (X) SVDATA READ Status display (X) ERR DP MODE Error history display, clear SLED MOVE Sled check (X) ACCESS MODE Access check (X) 0920 CHECK Outermost circumference check (X) WRITE sure? Non-volatile memory Initialize (X) (!) HEAD ADJUST Head position check (X) CPLAY2 MODE Continuous playback mode (X) CREC2 MODE Continuous recording mode (X) Ver @@@@@ Microprocessor version display (X) (!) • For details of each adjustment mode, refer to the items in “6. Electrical Adjustments”. For details of “ERR DP MODE”, refer to the selfdiagnosis function on page 2. • If other modes are set accidentally, press the ^ (CD) button to exit that mode. • As items marked (X) in the “Mark” column are not used during servicing, they are not described here. If these modes are set accidentally, press the ^ (CD) button to exit the mode. Be especially careful with items marked (!) as they will overwrite the non-volatile memory, and as a result, the unit will not operate normally. 5-5-1. Operating the Continuous Playback Mode 1. Entering the continuous playback mode 1 Set the disc in the unit. (Recordable discs or discs for playback only.) 2 Rotate the VOLUME knob and display “CPLAY MODE”. 3 Press the p (CD) button to change the display to “CPLAY MID”. 4 When access completes, the display changes to “C = AD = ”. Note : The numbers “ ” displayed indicate the error rates and “ADER”. 2. Changing the part to be played back 1 When the p (CD) button is pressed during continuous playback, the display changes as below, and the played back part can be changed. “CPLAY MID” n “CPLAY OUT” n “CPLAY IN” 2 When access completes, the display changes to “C1 = AD = ”. Note : The numbers “ ” displayed indicate the error rate and “ADER”. – 19 – 3. Ending the continuous playback mode 1 Press the ^ (CD) button. The display changes to “CPLAY MODE”. 2 Press the 6 (MD) button to remove the disc. Note : The playback start addresses for IN, MID, and OUT are as follows. To display the playback position address on the display, press the 1/u button to display “CPLAY ( )”. IN: 40h cluster MID: 300h cluster OUT: 700h cluster 5-5-2. Operating the Continuous Recording Mode 1. Entering the continuous recording mode 1 Set a recordable disc in the unit. (Refer to Note 3.) 2 Rotate the VOLUME knob and display “CREC MODE”. 3 Press the p (CD) button to change the display to “CREC MID”. 4 When access completes, the display changes to “CREC ( )” and the REC display lights up. Note : The numbers “ ” displayed indicate the recording position address. 2. Changing the part to be recorded 1 When the p (CD) button is pressed during continuous recording, the display changes as below and the recorded part can be changed. The REC display is off while changing. “CPLAY MID” n “CPLAY OUT” n “CPLAY IN” 2 When access completes, the display changes to “CREC MODE” and the REC display lights up. Note : The numbers “ ” displayed indicate the recording position address. 3. Ending the continuous recording mode 1 Press the ^ (CD) button. The display changes to “CREC ( )”, and the REC display lights up. 2 Press the 6 (MD) button to remove the disc. Note 1 : The recording start addresses for IN, MID, and OUT are as follows. IN: 40h cluster MID: 300h cluster OUT: 700h cluster Note 2 : The ^ (CD) button can be used to stop recording anytime. Note 3 : Do not perform continuous recording for long periods of time above 5 minutes. Note 4 : During continuous recording, be careful not to apply vibration. 5-5-3. Non-Volatile Memory Mode (EEP MODE) This mode reads and writes the contents of the non-volatile memory. It is not used in servicing. If set accidentally, press the ^ (CD) button immediately to exit it. 5-6. FUNCTIONS OF OTHER BUTTONS Contents Function ·P Sets continuous playback when pressed in the STOP state. Turns ON/OFF the tracking servo when pressed during continuous playback. p Stops the continuous playback and recording. )+ Moves the sled to the external circumference only while the button is pressed. =0 Moves the sled to the internal circumference only while the button is pressed. CD-MD SYNC Switches between pit and groove when pressed. 1/u Switches the displayed contents when pressed. 6 (MD) Ejects the disc. REPEAT Exits the test mode. – 20 – 5-7. DISPLAYS DURING TEST MODE The display changes according to the following sequence each time the 1/u button is pressed. 1. Mode display “TEMP ADJUST” and “CPLAYMODE” are displayed. Mode display 2. Error rate display The error rate is displayed as follows. C= AD = C = :Indicates the C1 error. AD = :Indicates ADER. Error rate display Address display Auto gain display (Not used in servicing) 3. Address display The address is displayed as follows. (MO: Recordable disc, CD: Disc for palyback only) When the CD-MD SYNC button is pressed, the display will switch between groove and pit. h= s= (MO pit and CD) a= (MO groove) h= h = Indicates the header address. s = Indicates the SUBQ address. a = Indicates the ADIP address. Note: Displayed as “–” when servo is operated. 4. Auto gain display (Not used in servicing) The auto gain is displayed as follows. AG = / . 5. Detrack check display (Not used in servicing) The detrack is displayed as follows. ADR = 6. IVR display (Not used in servicing) IVR is displayed as follows. ][ ][ [ Meanings of other displays Contents Display When Off When Lit REC Recording mode ON ATT ABCD adjustment completed OVER Tracking offset cancel ON SHUFFLE Focus auto gain OK TRACK Pit Groove DISC High reflection rate Low reflection LEVEL-SYNC CLV-S CLV-A SYNC CLV LOCK CLV UNLOCK Recording mode OFF Tracking offset cancel OFF – 21 – Detrack check display (Not used in servicing) IVR display (Not used in servicing) 5-8. AGING MODE This unit is provided with an aging mode. In this mode, MD and CD operations are performed alternately according to the following sequence. Aging will be carried out continuously unless an error occurs. If an error occurs, the status and number of cycles are displayed alternately, and operations stop. (Refer to Table 1.) Aging Mode Sequence Start Turn ON Power using function MD MD TOC READ Cannot read Message 6 Can read Above 20 MD all erase Blank disc MD last track NO Less than 20 Message 1 YES CD function is set and CD TOC is read CD TOC OK? NO Message 7 YES CD synchro standby OK? NO Message 2 or 8 YES CD last track search pause state OK? NO Message 9 YES CD synchro starts OK? NO Message 3 or 0 YES Synchro ends? Playing CD? OK MD function is set NG Message !º CD tray opens OK? NO Message !¡ YES CD tray closes OK? NO Message !™ YES MD last track (for 3 sec.) play OK? NO Message 4 YES Power goes off and MD TOC is written Aging cycle number is displayed Power turns ON and MD TOC is read OK? NO Message 5 or Message 6 YES – 22 – Procedure: 1. Load a recordable disc (MD) and CD test disc (YEDS-18). (*Note 1) 2. While pressing the PLAY MODE button, press the ^ (CD) button. 3. Aging is executed in the above sequence. 4. To end, press the p (CD or MD) button. *Note 1: Any CD can be used, but one with a short last track is recommended. The time of one aging cycle will be longer if the last track is long. Also use a CD in which the length of the last track x 20 does not exceed the recording time of the recording MD. Table 1. Messages and Main Causes When Aging Stops No 1 Error Messages MD A Erase NG Details of Error Cannot MD all erase. Main Causes A disc for playback only was used. The rec-proof tab is set to protect. Disc error, etc. 2 MD R-Pause NG Cannot set MD Rec Pause. 3 MD D-input NG Cannot lock MD digital in. 4 MD Play NG Cannot play last track. Access error, etc. 5 MD TOC NG MD TOC are different. No. of total tracks does not match logic value. 6 MD No Disc NG Cannot read MD TOC. Disc error, etc. 7 CD No Disc NG Cannot read CD TOC. Optical defect, spindle defect (including motor), cannot read Disc is full, etc. Q data, disc defect (scratches, etc.), bad focus, bad GFS, etc. 8 CD Pause NG 9 CD Search NG Cannot search last track on CD. 0 CD Play NG Cannot play last track on CD. !¡ CD Open NG Cannot open CD tray. LOAD OUT SW defect !™ CD Close NG Cannot close CD tray. LOAD IN SW defect Cannot set CD pause in Disc defect (scratches, etc.), cannot read Q data, etc. CD synchro mode. Optical defect, sled, tracking defect (including motor), cannot read Q data, disc defect (scratches, etc.). Optical defect, cannot read Q data, disc defect (scratches, etc.), etc. – 23 – SECTION 6 ELECTRICAL ADJUSTMENTS MD SECTION 6-1. PRECAUTIONS FOR CHECKING LASER DIODE EMISSINON When checking the emission of the laser diode during adjustments, never view directly from the top as this may cause blindness. 6-4. CREATING THE CONTINUOUSLY RECORDED DISC 6-2. PRECAUTIONS FOR USE OF OPTICAL PICKUP (KMS-260A) As the laser diode in the optical pick-up is easily damaged by static electricity, solder the laser tap of the flexible board when using it. Before disconnecting the connector, solder first. Before connecting the connector, be careful not to remove the solder. Also take adequate measures to prevent damage by static electricity. Handle the flexible board with care as it breaks easily. pick-up Note : When performing laser power checks and adjustment (electrical adjustment), use of the new MD laser power meter 8010S (J-2501-145-A) instead of the conventional laser power meter is convenient. It sharply reduces the time and trouble to set the laser power meter sensor onto the objective lens of the pick-up. flexible board • The disc is used for the focus bias adjustment and error rate check. The following describes how to create a continuously recorded disc. 1. Insert a disc (blank disc) commercially available. 2. Rotate the VOLUME knob to display “CREC MODE”. 3. Press the p (CD) button to display “CREC MID”. “CREC (0300)” will be momentarily displayed and recording started. 4. Complete recording within 5 minutes. 5. Press the ^ (CD) button and stop recording . 6. Press the 6 (MD) button and remove the disc. Create the continuous recorded disc for adjusting the focus bias and checking the error rate as described above. Note : • Be careful not to apply vibrations during continuous recording. 6-5. TEMPERATURE COMPENSATION OFFSET ADJUSTMENT laser tap Optical pick-up flexible board Save the current temperature data in the non-volatile memory as the 25 °C standard data. 6-3. PRECAUTIONS FOR ADJUSTMENTS 1) When replacing the following parts, perform adjustments and checks marked ¬ in the order shown in the following table. Optical Pick-up IC171 BD Board D101 IC101, IC121, IC192 1. Temperature compensation offset adjustment G ¬ ¬ ¬ 2. Laser power adjustment ¬ ¬ G ¬ 3. Traverse adjustment ¬ ¬ G ¬ 4. Focus bias adjustment ¬ ¬ G ¬ 5. Error rate check ¬ ¬ G ¬ 2) Perform the adjustment in the test mode. After completing the adjustments, exit the test mode. 3) Perform the adjustments in the order shown. 4) Use the following tools and measuring devices. • Check disc (MD) TDYS-1 (Parts No. 4-963-646-01) • Laser power meter LPM-8001 (Parts No. J-2501-046-A) or MD Laser power meter 8010S (Parts No. J-2501-145-A) • Oscilloscope (Measure after calibration of the probe). • Digital voltmeter • Thermometer 5) When observing several signals on the oscilloscope, etc., make sure that VC and ground do not connect inside the oscilloscope. (The VC and ground will short-circuit.) Notes: 1. Normally, this adjustment should not be preformed. 2. Set the surrounding temperature to 22 to 28 °C when performing this adjustment. Also perform this adjustment immediately after the power is turned on when the internal temperature of the unit is the same as the surrounding temperature (22 to 28 °C). 3. After replacing D101, perform this adjustment after the temperature of parts reach the surrounding temperature. Adjusting Procedure: 1. Rotate the VOLUME knob, to display “TEMP ADJUST”. 2. Press the p (CD) button and select the “TEMP ADJUST” mode. ” and the current temperature data are displayed. 3. “TEMP= 4. To save the data: Press the p (CD) button. If not saving the data: Press the ^ (CD) button. 5. When the p (CD) button is pressed, “TEMP= SAVE” is displayed, and then “TEMP ADJUST” is displayed again. “TEMP ADJUST” is displayed again immediately after the ^ (CD) button is pressed. Specifications: TEMP= should be E0 to EF. F0 to FF, 00 to 0F, 10 to 1F and 20 to 2F. – 24 – 6-6. LASER POWER ADJUSTMENT 6-7. TRAVERSE ADJUSTMENT Connection : Connection : Laser power meter Oscilloscope BD (MD) board TP (TEO) TP (VC) Optical pick-up objective lens Digital volt meter BD (MD) board TP (I+3V) TP (IOP) Adjusting Procedure: 1. Set the laser power meter on the objective lens of the optical pick-up from the disc slot. (If it cannot be set properly, press the = 0 or ) + button to move the optical pick-up). Connect the digital voltmeter to TP (I+3V) and TP (IOP) of the BD (MD) board. 2. Rotate the VOLUME knob to display “LDPWR ADJUST”. (Laser power: For adjustment) 3. Press the p (CD) button once to display “LD 0.9 mW $ ”. 4. Rotate the VOLUME knob so that the laser power meter reads 0.86 to 0.92 mW. Set the range knob of the laser power meter to 10 mW, press the p (CD) button, and save the adjustment results in the non-volatile memory. (“LD SAVE $ ” is displayed momentarily.) 5. “LD 7.0 mW $ ” is next displayed. 6. Rotate the VOLUME knob so that the laser power meter reads 6.9 to 7.1 mW, press the p (CD) button, and save the adjustment results in the non-volatile memory. (“LD SAVE $ ” is displayed momentarily.) Note: Do not emit 7.0 mW continuously for more than 15 seconds. 7. Rotate the VOLUME knob to display “LDPWR CHECK”. 8. Press the p (CD) button once to display “LD 0.9 mW $ ”. Check that the laser power meter reading is 0.85 to 0.91 mW. 9. Press the p (CD) button another time to diaplay “LD 7.0 mW $ ”. Check that the readings of the laser power meter and digital voltmeter become the specified value. Specified Value : Laser power meter reading : 7.0 ± 0.1 mW Digital voltmeter reading : Value displayed on optical pick-up label ± 10% Adjusting Procedure: 1. Connect an oscilloscope to TP (TEO) and TP (VC) of CN110 of the BD (MD) board. 2. Load a recordable disc (any available on the market). (Refer to Note 1.) 3. Press the = 0 or ) + button to move the optical pick-up outside the pit. 4. Rotate the VOLUME knob to display “EFBAL ADJUST”. 5. Press the p (CD) button to display “EFB = MO-R”. (Laser power READ power/Focus servo ON/tracking servo OFF/ spindle (S) servo ON) 6. Rotate the VOLUME knob so that the oscilloscope waveform becomes the specified value. (Rotating the VOLUME knob changes the “EFB= ” value and the waveform.) The waveform changes by about 2% everytime when adjusted. Adjust as close as possible to the specified value. (Read power traverse adjustment) (Traverse Waveform) A VC B Specified value : A = B 7. Press the p (CD) button and save the adjustment results in the non-volatile memory (displayed as “EFB = SAVE” MO-W”). momentarliy and then displayed as “EFB = 8. Rotate the VOLUME knob so that the oscilloscope waveform becomes the specified value. (Rotating the VOLUME knob changes the “EFB= ” value and the waveform.) The waveform changes by about 2% everytime when adjusted. Adjust as close as possible to the specified value. (Write Power Traverse Adjustment) (Traverse Waveform) (Optical pick-up label) A KMS 260A 27X40 B0825 VC N B Iop = 82.5 mA in this case Iop (mA) = Digital voltmeter reading (mV)/1 (Ω) Specified value : A = B 10. Press the ^ (CD) button to display “LDPWR CHECK” and stop the laser emission. (The ^ (CD) button is effective at all times to stop the laser emission.) 9. Press the p (CD) button to save the adjustment results in the SAVE” non-volatile memory (displayed as “EFB = momentarliy). – 25 – 10. Next “EFB = MO-P” is displaed, the optical pick-up moves to the internal circumference of the pit and servo is imposed. 11. Rotate the VOLUME knob so that the oscilloscope waveform becomes the specified value. The waveform changes by about 2% everytime when adjusted. Adjust as close as possible to the specified value. (Traverse Waveform) A VC B Specified value : A = B 12. Press the p (CD) button and save the adjustment results in the non-volatile memory (displayed as “EFB = SAVE” momentarliy). “EFBAL: CD is next displayed and the disc stops rotating automatically. 13. Press the 6 (MD) button and remove the disc. 14. Load the check disc (MD) TDYS-1. 15. Press the p (CD) button to display “EFB = CD”. The servo is imposed automatically. 16. Rotate the VOLUME knob so that the oscilloscope waveform becomes the specified value. The waveform changes by about 2% everytime when adjusted. Adjust as close as possible to the specified value. (Traverse Waveform) A VC B 6-8. FOCUS BIAS ADJUSTMENT Adjusting Procedure : 1. Load a continuously recorded disc (Refer to 6-4. Creating the Continuously Recorded Disc”). 2. Rotate the VOLUME knob to display “CPLAY MODE”. 3. Press the p (CD) button to display “CPLAY MID”. 4. When “C1 = AD = ” is displayed, press the ^ (CD) button. 5. Rotate the VOLUME knob to display “FBIAS ADJUST”. 6. Press the p (CD) button to display “ / a = ”. The first four digits indicate the C1 error rate, the two digits after the “/” indicate ADER and the two digits after “a =” indicate the focus bias value. 7. Rotate the VOLUME knob in the clockwise direction, and look for the focus bias value at which the C1 error rate becomes approximately approx. 200. (Refer to Note 2). / b = ”. 8. Press the p (CD) button to display “ 9. Rotate the VOLUME knob in the counterclockwise direction, and look for the focus bias value at which the C1 error rate becomes approx. 200. Check that the C1 error rate becomes almost equal to the value set in step 7. 10. Press the p (CD) button to display “ / c = ”. 11. Check that the C1 error rate is below 50 and that ADER is 00. and press the p (CD) button. 12. If the value of “( )” in the “ ( )” displayed is above 20, press the p (CD) button. If below, press the ^ (CD) button and start from step 2 again. 13. Press the 6 button and remove the continuously recorded disc. Note 1 : The following figure shows the relation between the C1 error and focus bias value. Look for points a and b in the following figure by the adjustment avove. The focus position (point c) is automatically calculated from points a and b. Note 2 : As the C1 error rate changes, use the average value in the adjustment. C1 error Specified value : A = B 17. Press the p (CD) button and save the adjustment results in the non-volatile memory after “EFB = SAVE” is momentarliy displayed. “EFBAL ADJUST” is next displayed. 18. Press the 6 (MD) button and remove the check disc (MD) TDYS-1. approx. 200 Note 1 : The data will be overwritten on the MO and erased when a recorded disc is used in this adjustment. Note 2 : If the traverse waveform is not clear, connect the oscilloscope as shown in the following figure so that it can be seen more clearly. Oscilloscope BD (MD) board TP (TEO) TP (VC) 330 kΩ 10pF – 26 – b c a Focus bias value (F. BIAS) 6-9. ERROR RATE CHECK 6-9-1. CD Error Rate Check Checking Procedure : 1. Load a check disc (MD) TDYS-1. 2. Rotate the VOLUME knob to display “CPLAY MODE”. 3. Press the p (CD) button to display “CPLAY MID”. 4. “C1 = AD = ” is displayed. 5. Check that the C1 error rate is below 20. 6. Press the ^ (CD) button to stop playback. Then press the 6 (MD) button, and remove the check disc (MD). 6-9-2. MO Error Rate Checking Checking Procedure : 1. Load a continuously recorded disc (Refer to 6-4. Creating the Continuously Recorded Disc”). 2. Rotate the VOLUME knob to display “CPLAY MODE”. 3. Press the p (CD) button to display “CPLAY MID”. AD = ” is displayed. 4. “C1 = 5. Check that the C1 error rate is below 50 and ADER is 00. 6. Press the ^ (CD) button to stop playback. Then press the 6 (MD) button, and remove the disc. 6-10. FOCUS BIAS CHECK Change the focus bias value and check the focus tolerance amount. Checking Procedure : 1. Load a continuously recorded disc (Refer to 6-4. Creating the Continuously Recorded Disc”). 2. Rotate the VOLUME knob to display “CPLAY MODE”. 3. Press the p (CD) button to display “CPLAY MID”. 4. When “C1 = AD = ” is displayed, press the ^ (CD) button. 5. Rotate the VOLUME knob to display “FBIAS CHECK”. / c = ”. 6. Press the p (CD) button to display “ The first four digits indicate the C1 error, the two digits after the “/” indicate ADER and the two digits after “c =” indicate the focus bias value. Check that the C1 error is below 50 and ADER is 00. 7. Press the p (CD) button to change the display to “ / b= ”. Check that the C1 error does not drop below 220 and ADER does not remain above 00. 8. Press the p (CD) button to change the display to “ / a= ”. Check that the C1 error does not drop below 220 and ADER does not remain above 00. 9. Press the ^ (CD) button, press the 6 (MD) button next, and remove the continuously recorded disc. Note 1 : If the C1 error is above 220 or ADER is above 00 only for point a (step 8 above) and point b (step 7 above), the focus bias may not adjusted properly. In this case, adjust again. – 27 – 6-11. ADJUSTING POINTS AND CONNECTING POINTS [BD (MD) BOARD] (SIDE A) D101 IC192 [BD (MD) BOARD] (SIDE B) TP (IOP) TP (I + 3V) Q163 IC316 IC171 TP (VC) TP (TEO) IC101 Q102 IC121 – 28 – S Curve Check CD SECTION Note: 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10MΩ impedance. 4. Clean the object lens by an applicator with lens cleaning liquid when the signal level is low than specified value with the following checks. 5. Adjust the focus bias adjustment when optical block is replaced. Focus Bias Adjustment Perform this adjustment when the optical pick-up has been replaced or repaired. oscilloscope BD (CD) board TP (RF) TP (VC) oscilloscope BD (CD) board + – TP (FEO) TP (VC) Procedure : 1. Connect oscilloscope to test point TP (FEO). 2. Connect between test point TP (FOK) and Ground by lead wire. 3. Turn Power switch on. 4. Put disc (YEDS-18) in and turned Power switch on again and actuate the focus search. (actuate the focus search when disc table is moving in and out.) 5. Check the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 2.4 ± 0.7 Vp-p. + – S-curve waveform symmetry Procedure: 1. Connect oscilloscope to test point TP (RF). 2. Turned Power switch on. 3. Put disc (YEDS-18) in and playback. 4. Adjust RV101 so that the waveform is clear. (Clear RF signal waveform means that the shape “◊” can be clearly distinguished at the center of the waveform.) 5. After adjustment, check the RF signal level. • RF signal VOLT/DIV: 200 mV TIME/DIV: 500 nS A within 2.4 ± 0.7 Vp-p B 6. After check, remove the lead wire connected in step 2. Note: • Try to measure several times to make sure than the ratio of A : B or B : A is more than 10 : 7. • Take sweep time as long as possible and light up the brightness to obtain best waveform. RF Level Check oscilloscope level : 1.3 ± 0.3 Vp-p BD (CD) board TP (RF) TP (VC) + – Procedure : 1. Connect oscilloscope to test point TP (RF) on BD board. 2. Turned Power switch on. 3. Put disc (YEDS-18) in and playback. 4. Confirm that oscilloscope waveform is clear and check RF signal level is correct or not. Note: Clear RF signal waveform means that the shape “◊” can be clearly distinguished at the center of the waveform. RF signal waveform VOLT/DIV : 200 mV TIME/DIV : 500 nS level : 1.3 ± 0.3 Vp-p – 29 – E-F Balance (1 Track Jump) Check (Without remote commander) Adjustment Location: [BD (CD) BOARD] — Component Side — oscilloscope RF BD (CD) board + – RV101 IC101 TEI RV103 Procedure : 1. Connect oscilloscpe to test point TP (TEO) on BD board. 2. Turn Power switch on. 3. Put disc (YEDS-18) in to play the number five track. 4. Press the “P (Pause)” button. (Becomes the 1 track jump mode) 5. Confirm that the oscilloscope waveform is symmetrical on the top and bottom in relation to 0Vdc, and check this level. TEO VC FEO IC102 TP (TEO) TP (VC) FOK (Focus Bias Adjust) FEI RV102 1 track jump waveform IC104 PCK A 0V GND B LEVEL : 300 ± 100 mVp-p Specified level: • A–B x 100 = less than ± 7% 2 (A + B) • A + B = 300 ± 100 mVp-p 6. Remove the lead wire connected in step 1. Focus/Tracking Gain Adjustment (RV102, RV103) This gain has a margin, so even if it is slightly off. There is no problem. Therfore, do not perform this adjustment. Please note that it should be fixed to mechanical center position when you moved and do not know original position. – 30 – HCD-MD333 SECTION 7 DIAGRAMS 7-1. CIRCUIT BOARDS LOCATION POWER AMP board AUDIO board MAIN board MD LED board HP board ENCAPSULATED COMPONENT (US, Canadian, Malaysia, Singapore, HongKong, Argentine, Australian, Tourist) TUNER (FM/MW/LW) (AEP, UK, EE) PANEL board TRANS board JACK board ST TERMINAL board SW board BD (MD) board BD (CD) board LOADING board – 31 – HCD-MD333 7-2. BLOCK DIAGRAMS – CD SECTION – OPTICAL PICK-UP (KSS-213B) 34 B RV102 FOCUS GAIN F RV101 FOCUS BIAS 2 FEI FE-O FE-M TA-M TAO 44 TEI RV103 TRACKING GAIN PD +5V FE BIAS 37 1 FEO 42 TEO DIGITAL SIGNAL PROCESSOR IC103 55 CNIN 54 SEIN C.OUT 23 SENS 24 56 57 59 3 1 64 63 51 52 53 43 46 47 49 50 39 26 28 27 6 7 12 13 D OUT LASER DIODE 49 50 60 22 53 48 46 52 51 59 FOK 25 34 PHD FOCUS SW Q103 FGD 4 XRST 22 7 FOCUS COIL TRACKING COIL 18 17 T– 2-AXIS DEVICE F– F+ TRACKING COIL DRIVE MOTOR DRIVER IC801 19 TRACKING/FOCUS COIL DRIVE IC102 (1/2) 12 11 FOCUS COIL DRIVE 9 M904 (CD) LOADING MOTOR M M101 SPINDLE MOTOR M 2 DRIVE 5 10 DRIVE 6 57 LOAD-OUT M 58 LOAD-IN SLED SERVO IC101 (2/2) SLED/SPINDLE MOTOR DRIVE IC102 (2/2) M102 SLED MOTOR CLK DATA XRST SCOR SENS SQCK SQSO DF LATCH XLAT FOCUS SW XRST T+ 26 • 27 SLED MOTOR DRIVE 25 1 • 2 SPINDLE MOTOR DRIVE 4 16 SLO SL+ 14 56 S291 (LOAD OUT) 55 S292 (LOAD IN) 09 • SIGNAL PATH :CD :digital out (CD) – 33 – C MAIN SECTION (Page 37) DATA 21 XLT 20 CLK 19 33 LD MAIN SECTION (Page 37) S101 (LIMIT) LD LD DRIVE Q101, 102 A ROUT 13 DATA MLAT CLOK C 38 F 39 E DIGITAL FILTER D/A CONVERTER IC104 LOUT 16 D OUT D 2 DATA 1 LRCK 3 BCLK PCMD 21 LRCK 20 BCLK 22 XRST C 14 RF RFO 31 RFI 30 SCOR SQSO SQCK SENS B 35 PD1 36 PD2 DATA XLAT CLOK D SPOD A 5•6 DATAO XLTO CLKO MDP FOK XLON 1 4 2 5 10 6 A 4 CKO E XTI • XTO TRACKING/FOCUS SERVO, RF AMP IC101 (1/2) B+ K XTAI DETECTOR X101 22.5792 MHz – 34 – OUT-SW IN-SW B MAIN SECTION (Page 38) HCD-MD333 – MD SECTION – HR901 OVER WRITE HEAD OVER WRITE HEAD DRIVE Q181, 182 1 2 I J BPF C B D A E PEAK & BOTTOM PEAK J A B C D E F 4 5 6 7 8 9 A B C D E F ABCD AMP IV AMP 15 VC LASER ON SW Q101 PD PD 10 66 36 63 37 62 35 64 PCO FILI FILO CLTV 34 31 65 67 VC 74 73 29 BPF ADIN ADFG CVB TRACKING ERROR AMP TEMP AMP VICONV APCREF APC EQADJ 3TADJ WBLADJ + – 11 TE SE CSLED PD LASER DIODE 22 23 25 12 PLL DIGITAL AUDIO I/F ATRAC ENCODER/ DECODER SERIAL ↓ PARALLEL DECODER DADT DOUT RFI AUX1 CLOCK GENERATOR SAMPLING RATE CONVERTER BOTM PEAK FS256 XBCK LRCK OSCI OSCO SQSY DQSY SUBCODE PROCESSOR ABCD FE VC 30 32 78 ADFG SWDT SCLK XLAT FOCNT 26 28 27 A/D CONVERTER ADIP DEMODULATOR/ DECODER APC SENS SRDT SCLK SWDT XLAT CPU I/F SERVO DSP 3 SPINDLE SERVO VC 16 17 18 82 81 80 20 79 MNT3 MNT2 MNT1 MNT0 MONITOR CONTROL TE SE TEMPR TEMPI ADDT SHOCK RESISTANT MEMORY CONTROLLER EFM, ACIRC, ENCODER/ DECODER ADFM D101 14 33 VC VC VCC 3 FE IV AMP AT AMP 55 38 DIN EFMO ANALOG MUX FOCUS ERROR AMP VC VC ABCD 58 59 60 61 BUFFER IC401 XINIT TX AUX BOTM E-F BALANCE LD RF P-P F I 100 RF AGC & EQ RF AMP 14 PWM GENERATOR AUTO SEQUENCER 20 DTRF CKRF XLRF FOCNT 93 94 95 10 13 APCREF FFDR FRDR TFDR TRDR SFDR SRDR MORFO MORFI RFO AGCI I J IC181 (4/4) 12 11 13 RF AMP IC101 48 47 46 40 OPTICAL PICK-UP BLOCK (KMS-260A/J1N) DETECTOR 15 IC181 (1/4) 1 3 2 RECP : digital out (CD) SCTX XINT XRST : REC SPRD SPFD FG IN : PB (MD) FILTER • SIGNAL PATH DIGITAL SERVO SIGNAL PROCESSOR, DIGITAL SIGNAL PROCESSOR EFM/ACIRC ENCODER/DECODER, SHOCK-PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER, 2M-BIT DRAM IC121 OVER WRITE HEAD DRIVE IC181 (2/4) IC181 (3/4) 4 9 6 8 5 10 83 88 89 86 85 92 91 7 21 ADDT 24 DADT 22 27 26 25 16 FS256 BCK LRCK X101 22 MHz 17 11 12 SQSY DQSY 4 3 2 1 MNT3 MNT2 MNT1 MNT0 9 8 6 5 7 SENS SRDT SCLK SWDT XLAT DRAM IC124 XWE XRAS XCAS XOE 45 44 42 41 3 4 17 16 D MAIN SECTION XWE XRAS XCAS XOE DQ1 | | | | DQ4 (Page 37) 6 A0 ı | 9 | • | 11 | | ı 15 || • 5 A9 A0 –––––––––– A9 32–29 • 34–38 • 43 APC Q162, 163 ILCC DIN 23 1 • 2 • 18 • 19 D0 –––––––– D3 47 • 46 • 48 • 49 1 LDON HF MODULE WRPWR HF MODULE SW IC103, Q102-104 MOD TRACKING COIL MOD SLED/SPINDLE MOTOR DRIVE FOCUS/TRACKING COIL DRIVE IC152 FOCUS COIL TRK– TRK+ FSC+ FSC– M902 SLED MOTOR M901 SPINDLE MOTOR M SLED+ SLED– M SPDL+ SPDL– 15 10 12 DRIVER 23 DRIVER DRIVER 30 4 6 8 18 29 27 25 14 19 21 DRIVER 3 PSB 16 SDA SCL TRDR TFDR DETECT SW S681 - 683, S685 - 688 FFDR FRDR SFDR SRDR SPRD SPFD M903 (MD) LOADING MOTOR XRST M LIMIT REFLECT PROTECT CHUCK IN PACK OUT PB P REC P LOAD-IN LOAD-OUT XRST 09 – 35 – SDA 5 SCL 6 EEP ROM IC171 – 36 – HCD-MD333 – MAIN SECTION – SOUND PROCESSOR IC701 TUNER UNIT ANTENNA R-CH R-CH POWER AMP IC1201 7 1 DBFB SW Q701 2 MUTE Q702 R-CH D881 18 13 THP1230 6 4 MUX LDON WRPWR MOD LOAD-OUT 2 9 DRIVE 10 DRIVE SCTX EMP XINT DA-EN SQSY AD-EN DQSY MNT3 MNT2 MNT1 MNT0 SENS SRDT SCLK SWDT XLAT LIMIT-IN REFLECT PROTECT CHUCK-IN PACK-OUT PB.P MEC-BUSY REC.P MD SYSTEM CONTROL IC316 49 LDON 44 WRPWR TXD 50 MOD 51 LDIN 7 24 25 16 23 24 MCLK ∆∑ MOD LPF 8X INTERPOLATOR ∆∑ MOD LPF AOUTR DECIMATION FILTER ∆∑ MOD DECIMATION FILTER ∆∑ MOD AINL 27 R-CH 5 3 12 13 11 REC MUTE Q410 R-CH R-CH REC MUTE DRIVER Q871 31 1 13 21 20 75 77 63 41 37 38 39 31 100 35 45 44 43 42 61 22 46 48 49 50 51 52 53 59 60 55 56 57 58 18 19 MASTER CONTROL IC601 16 9 VF 12 3 11 24 ı 31 • 33 ı 59 VF 10 DIG11 ı DIG2 • DIG14 ı DIG12 1 ı 10 • 62 ı 64 FLUORESCENT INDICATOR TUBE FL901 4 SEG35 ı SEG27 • SEG27 ı SEG0 RST CS SCK SDATA 3 +B DIG1 11 SW Q901 DIG15 61 SW Q902 66 – 70 • 72 • 73 LED 10 11 13 14 15 X601 5 MHz X602 32 kHz RESET SW Q602 3 RESET IC602 1 3 +7V REG. 1 IC511 3 M+5V 1 +5V REG. SYS+3.3V 5 +3.3V REG. +10V REG. 1 IC510 RECT D501 ı D504 +7.5V REG. Q510 –7.5V REG. Q520, 521 –7.5V +5V (AC IN) RECT D1300 –B +10V M+7V +3.3V REG. 1 IC192 VOLTAGE SELECTOR S1600 (JE, HK, AR, AUS) • R CH : Same as L CH • SIGNAL PATH 3 : FM 52 LDOUT ANA+5V 4 +5V REG. B.UP +3.3V 6 BACK UP : PB –29V REG. Q530 –VG : REC : CD DRIVER Q601 79 SDA SYSTEM- 12 80 SCL RST 40 DIG-RST PDOWN 53 LD-LOW PWR-DWN 19 XOUT XIN 13 15 09 25 – 27 T1600 POWER TRANSFORMAER 4 LOADING MOTOR DRIVE LOADING SW IC153 Q350 SDA SCL XRST 90 CN402 AU BUS 13 14 15 16 +7.5V +3.3V (BD) RXD 32 CLK 33 MAS-BUSY 34 LED DRIVE Q904 – 910 S902 – 916 8 DISPLAY DRIVER IC901 2 17 AU BUS SW Q420 LEVEL CONVERT IC840 26 ROTARY ENCODER S901 (OPEN) 10 VOLUME (Page 34) B A/D, D/A CONVERTER IC201 OPTICAL SELECTOR IC842 CD SECTION 26 74 76 82 83 84 85 86 87 88 34 CLOCK DIVIDER DEMO PDDA PDAD AOUTL XO 14 D902 – 908 SIRCS IC902 22 46 48 49 50 51 52 53 59 60 55 56 57 58 SERIAL I/O INTERFACE 8X INTERPOLATOR RDATA RCLK 2 16 X1501 4.332 MHz RESET SLOCK XBUSY 42 23 5 20 45 46 47 48 41 36 37 35 38 59 55 54 58 57 61 60 SDTO SDTI SCLK LRCK XI 13 XT1 J402 TAPE OUTPUT KEY-0 ı KEY-2 L A R ST-MUTE AC-CUT POWER-ON MD-OEM/REST RESET CS RDS/DATA CLOCK DATA RDS/CLK CD-POWER 15 4 J1400 PHONES RDS DECODER IC1500 82 83 84 85 86 87 88 14 13 12 11 ADDT DADT BCK LRCK DIN FS256 LOAD-IN R-CH +B REC OUT.MUTE DBFB ATT/6DB MUTE D.IN.SELECT STEREO MECHA BUSY TUNED RXD DATA-IN TXD DATA-OUT MD-CLK CLOCK MASTER BUSY CE (Page 34) C (Page 36) R-CH (AEP, UK, EE) IC1501 BUFFER CD SECTION D FAN DRIVE Q591, 592 + POWER SW Q431 R-CH MD SECTION FAN901 DC DETECT SW Q433 OVER LOAD DETECT SW Q434 R-CH SCTX XINT SQSY DQSY MNT3 MNT2 MNT1 MNT0 SENS SRDT SCLK SWDT XLAT LIMIT REFLECT PROTECT CHUCK-IN PACK-OUT PB-R REC-R R RELAY SW Q432 HEAT SENSOR SW Q1231, 1232 GAIN CONTROL Q400 GAIN CONTROL DRIVER Q872 TM440 SPEAKER + R-CH RELAY DRIVE Q435, 436 OVER LOAD DET Q1251 POWER SW Q1202 R-CH – R-CH 16 MUTE SW Q703 L R-CH – + – 17 R-CH D882 + 10 OVER LOAD DET Q1201 R-CH 18 RY430 + – XT2 L B R + 6 – SIRCUS J401 TAPE INPUT 25 X1 FM 300 Ω (Page 34) A 29 ECN/A ECN/B FM 75 Ω CD SECTION 30 5 X2 AM AMP IC702 39 38 37 36 35 4 5 6 7 8 SCOR (BD) SUBQ SQCLK CLOCK DATA XLT DF.LAT SENCE FOCUS-SW BD-REST AU-BUS IN IN-SW OUT-SW LOAD-OUT AU-BUS OUT LOAD-IN STEREO TUNED DO DI CLK CE MUTE RDS 82 83 84 85 86 87 88 3 MD RESET IC603 5 2 9 D581 MD REG. IC570 8 CD+5V POWER ON/OFF SW Q571, 572 X302 7 MHz – 37 – D582 +5V 7 RECT D551 ı D554 3 +5V REG. 1 IC560 CP POWER SW Q561, 562 VF – 38 – : digital out (CD) : TAPE • Abbreviation CND : Canadian model. EE : East European model. SP : Singapore model. MY : Malaysia model. HK : Hong Kong model. JE : Tourist model. AR : Argentine model. AUS : Australian model. HCD-MD333 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) WAVEFORMS – CD SECTION – – MD SECTION – – MAIN SECTION – 1 1 3.4 Vp-p Approx. 500 mVp-p 1.3 ± 0.3 Vp-p For schematic diagrams. IC101 #¡ (RFO) (PLAY Mode) 500 mV/DIV, 500 ns/DIV 2 2 5 MHz IC121 (º (FS4) IC601 !¡ (XI) 2 8 3.1 Vp-p Approx. 200 mVp-p IC101 $¢ (TEI) (PLAY Mode) 50 mV/DIV, 1 µs/DIV 3 IC601 !¢ (XI) IC121 !¶ (OSCI) IC101 4 (A) (PLAY Mode) 9 3 3.4 Vp-p Approx. 150 mVp-p Approx. 150 mVp-p 44.1 kHz IC101 2 (FEI) (PLAY Mode) 50 mV/DIV, 1 µs/DIV 4 IC121 @∞ (LRCK) IC101 8, 9 (E, F) (PLAY Mode) !º 4 3.5 Vp-p 1.2 ± 0.2 Vp-p 2.6 Vp-p 2.8224 MHz 7.6 µs IC103 3 (MDP) (PALY Mode) Signal path. F : FM E : PB (MD) m : PB (TAPE) n : REC J : CD c : digital out • Abbreviation CND : Canadian model. EE : East European model. SP : Singapore model. MY : Malaysia model. JE : Tourist model. HK : Hong Kong model. AR : Argentine model. AUS : Australian model. 5 IC101 #• (RF) (PLAY Mode) IC121 @§ (XBCK) !¡ 5 4.6 Vp-p 3.4 Vp-p 5.1 Vp-p 11.2896 MHz 1.5 µsec 136 µs IC121 @¶ (FS256) IC152 #™ (CAPA–) (PLAY Mode) IC103 @• (RFCK) 6 6 !™ 4.6 Vp-p 3.3 Vp-p 5.3 Vp-p 1.5 µsec 14 ns IC152 #™ (CAPA+) (PLAY Mode) 7 MHz IC316 !£ (XOUT) IC103 @∞ (XPCK) 7 For printed wiring boards. Note: • X : parts extracted from the component side ® • : Through hole. ¢ • : internal component. • b : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) 5 Vp-p 474 ns IC103 @™ (BCLK) 8 5.1 Vp-p Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. 22.8 µs IC103 @º (LRCK) 9 • Indication of transistor 4.6 Vp-p C Q B E These are omitted 16.9344 MHz BC E IC104 6 (XTO) These are omitted – 39 – 2.6 Vp-p 32 kHz 22.5792 MHz • U : B+ Line. • V : B– Line. • H : adjustment for repair. Caution: Pattern face side: (Side B) Parts face side: (Side A) IC501 1, 2 (I.J) (PLAY Mode) Approx. 100 mVp-p M Note: Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce por tant le numéro spécifié. 4.3 Vp-p 5.7 µsec Note: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1 /4 W or less unless otherwise specified. ¢ • : internal component. • 2 : nonflammable resistor. • 1 : fusible resistor. • : Switch with sliding contact indicated by hatched lines shows shorting type. • C : panel designation. Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. 1 7 – 40 – HCD-MD333 7-3. SCHEMATIC DIAGRAM – CD SECTION – • See page 39 for Waveforms. • See page 81 for IC Block Diagrams. (Page 55) – 41 – – 42 – HCD-MD333 7-4. PRINTED WIRING BOARD – CD SECTION – • See page 31 for Circuit Boards Location. (Page 59) • Semiconductor Location • Semiconductor Location Ref. No. Location Ref. No. Location IC103 C-1 Q101 Q103 B-3 C-3 IC101 IC102 IC104 B-1 B-1 C-3 Q102 B-1 – 43 – – 44 – HCD-MD333 7-5. SCHEMATIC DIAGRAM – MD (1/3) SECTION – • See page 40 for Waveforms. • See page 51 for Printed Wiring Board. (Page 47) • See page 84 for IC Block Diagrams. • See page 88 for IC Pin Functions. (Page 47) – 45 – (Page 48) (Page 48) – 46 – HCD-MD333 7-6. SCHEMATIC DIAGRAM – MD (2/3) SECTION – • See page 40 for Waveforms. • See page 51 for Printed Wiring Board. • See page 85 for IC Block Diagrams. • See page 89 for IC Pin Functions. (Page 45) (Page 45) (Page 46) (Page 46) (Page 55) (Page 49) (Page 49) – 47 – (Page 50) – 48 – HCD-MD333 7-7. SCHEMATIC DIAGRAM – MD (3/3) SECTION – • See page 40 for Waveforms. • See page 83 for IC Block Diagrams. • See page 92 for IC Pin Functions. (Page 47) (Page 47) (Page 48) (Page 53) – 49 – – 50 – HCD-MD333 7-8. PRINTED WIRING BOARD – MD SECTION – • See page 31 for Circuit Boards Location. (Page 54) (Page 59) • Semiconductor Location Ref. No. Location D101 A-2 IC192 IC401 C-4 D-4 • Semiconductor Location – 51 – Ref. No. Location Ref. No. Location D181 D183 B-1 B-1 IC316 A-2 IC101 IC103 IC121 IC124 IC152 IC153 IC171 IC181 IC201 B-3 B-4 C-4 D-4 A-4 A-1 A-3 B-1 D-3 Q101 Q102 Q103 Q104 Q162 Q163 Q181 Q182 Q350 B-3 B-4 B-4 B-4 B-4 A-3 B-1 B-1 A-1 – 52 – HCD-MD333 7-9. SCHEMATIC DIAGRAM – MD SWITCH SECTION – 7-10. PRINTED WIRING BOARD – MD SWITCH SECTION – • See page 31 for Circuit Boards Location. (Page 51) (Page 50) – 53 – – 54 – HCD-MD333 7-11. SCHEMATIC DIAGRAM – MAIN (1/3) SECTION – • See page 40 for Waveforms. • See page 59 for Printed Wiring Board. • See page 86 for IC Block Diagrams. • See page 94 for IC Pin Functions. (Page 73) (Page 61) (Page 62) (Page 69) (Page 57) (Page 42) (Page 47) (Page 73) (Page 66) – 55 – – 56 – HCD-MD333 7-12. SCHEMATIC DIAGRAM – MAIN (2/3), (3/3) SECTION – • See page 86 for IC Block Diagrams. (Page 77) (Page 56) (Page 75) – 57 – – 58 – HCD-MD333 7-13. PRINTED WIRING BOARD – MAIN SECTION – • See page 31 for Circuit Boards Location. (Page 44) (Page 63) (Page 52) (Page 64) (Page 72) (Page 79) (Page 76) (Page 67) (Page 74) (Page 74) • Semiconductor Location Ref. No. D501 D502 D503 D504 D511 D521 D531 D532 D533 D534 D551 D552 D553 D554 D561 D562 D563 D571 D572 – 59 – – 60 – Location A-9 A-9 A-9 A-9 D-9 C-7 E-7 E-7 D-7 D-7 C-9 C-9 C-9 C-9 E-9 E-7 E-5 D-9 C-10 Ref. No. Location Ref. No. Location D581 D582 D591 D601 D602 D603 D604 D605 D801 D802 D803 D881 D882 B-10 B-10 A-8 D-4 D-4 E-5 E-5 C-5 A-3 B-2 D-4 B-5 A-7 IC603 IC801 IC840 IC842 E-3 E-4 C-4 A-1 IC510 IC511 IC560 IC601 IC602 C-10 C-10 E-10 D-2 D-4 Q510 Q520 Q521 Q530 Q561 Q562 Q571 Q572 Q591 Q592 Q601 Q602 Q871 Q872 C-8 C-7 C-7 E-6 E-8 E-8 D-9 D-9 A-7 A-8 E-3 D-4 D-4 D-4 HCD-MD333 7-14. SCHEMATIC DIAGRAM – AUDIO SECTION – • See page 87 for IC Block Diagrams. (Page 55, 56) (Page 56) (Page 69) – 61 – – 62 – HCD-MD333 7-15. PRINTED WIRING BOARD – AUDIO SECTION – • See page 31 for Circuit Boards Location. • Semiconductor Location (Page 72) (Page 59) – 63 – (Page 59) – 64 – Ref. No. Location D701 D1501 C-3 B-4 IC701 IC702 IC1500 IC1501 B-2 B-3 A-4 B-5 Q701 Q702 Q703 Q751 Q752 A-3 C-4 C-3 B-3 C-3 HCD-MD333 7-16. SCHEMATIC DIAGRAM – PANEL SECTION – (Page 55) (Page 70) – 65 – – 66 – HCD-MD333 7-17. PRINTED WIRING BOARD – PANEL SECTION – • See page 31 for Circuit Boards Location. • Semiconductor Location (Page 59) (Page 71) – 67 – – 68 – Ref. No. Location D901 D902 D903 D904 D906 D907 D908 C-3 A-2 A-2 E-3 D-2 D-2 E-6 IC901 IC902 C-6 C-8 Q901 Q902 Q904 Q905 Q906 Q907 Q908 Q909 Q910 C-5 C-5 A-3 B-2 E-4 B-3 D-2 D-2 E-4 HCD-MD333 7-18. SCHEMATIC DIAGRAM – JACK SECTION – (Page 65) (Page 61) (Page 55) – 69 – (Page 78) – 70 – HCD-MD333 7-19. PRINTED WIRING BOARD – JACK SECTION – • See page 31 for Circuit Boards Location. (Page 67) (Page 79) (Page 63) (Page 59) • Semiconductor Location Ref. No. Location D422 D430 D447 D497 A-4 B-1 A-1 A-1 IC470 A-8 Q400 Q410 Q420 Q431 Q432 Q433 Q434 Q435 Q436 Q450 Q460 B-5 A-6 A-4 A-3 A-3 A-3 A-3 A-3 A-3 B-6 A-7 – 71 – – 72 – HCD-MD333 7-20. SCHEMATIC DIAGRAM – ST TERMINAL/LOADING SECTION – 7-21. PRINTED WIRING BOARD – ST TERMINAL/LOADING SECTION – • See page 31 for Circuit Boards Location. (Page 55) (Page 59) LOADING BOARD (Page 55) S292 (LOAD IN) S291 (LOAD OUT) CN291 5 4 3 (Page 59) M M904 (LOADING MOTOR) 2 1 1-634-461- – 73 – – 74 – 11 (11) HCD-MD333 7-22. SCHEMATIC DIAGRAM – TRANS SECTION – 7-23. PRINTED WIRING BOARD – TRANS SECTION – • See page 31 for Circuit Boards Location. (Page 78) (Page 58) (Page 60) – 75 – – 76 – (Page 79) HCD-MD333 7-24. SCHEMATIC DIAGRAM – POWER AMP SECTION – (Page 70) (Page 57) (Page 75) – 77 – – 78 – HCD-MD333 7-25. PRINTED WIRING BOARD – POWER AMP SECTION – • See page 31 for Circuit Boards Location. (Page 71) • Semiconductor Location (Page 60) Ref. No. Location D1201 D1202 D1203 D1213 D1251 D1263 D1300 C-2 B-1 B-2 C-2 D-2 E-2 B-3 IC1201 C-1 Q1201 Q1202 Q1231 Q1232 Q1251 C-2 B-2 B-1 B-1 E-2 (Page 76) – 79 – – 80 – HCD-MD333 PHD2 PHD1 PHD LD RF M RF O RF I CP CB CC1 CC2 FOK VCC 36 35 34 33 32 31 30 29 28 27 26 25 15 OP– 16 OP+ 17 OUT3A 18 OUT3B VCC DRIVE BUFFER DRIVE BUFFER 19 IN3A 20 IN3B 21 VCC 22 VCC 23 VC 24 IN4B 25 IN4A IC101 CXA1782BQ 26 OUT4B 28 GND • CD section 27 OUT4A IC102 BA6397FP 7-26. IC BLOCK DIAGRAMS DRIVE BUFFER LEVEL SHIFT – + – + THERMAL SHUT DOWN – + LEVELS DRIVER MUTE MIRR RF IV AMP1 IIL 24 SENS TTL 23 C. OUT LEVEL SHIFT + – FOK + + – – – + – REGULATOR + APC – + DFCT – DRIVE BUFFER DRIVE BUFFER DRIVE BUFFER • ADDRESS DECODER FE AMP • OUTPUT DECODER IIL 19 CLK IC103 CXD2507AQ + – XLAT CLOK SEIN CNIN DATO VDD XLTO PS1-4 CLKO TM1-7 SPOA TG1-2 64 63 62 61 60 59 58 57 56 55 54 53 52 18 VCC FZC COMP + E 39 FS1-4 BAL1-3 SPOB TOG1-3 SPOC XLON + – F IV AMP SPOD – + • TRACKING HPF COMP MDS 4 • ISET • PHASE COMPENSATION LPF COMP 17 ISET – TM6 TG1 FILI 8 + – 16 SL 0 TOG3 • FCS PHASE COMPENSATION TZC COMP LPFI 43 FS1 TM7 ATSC FS2 45 EXCK 44 SBSO 43 SCOR 42 VSS 3 41 WFCK ASYMMETRY CORRECTOR 40 EMPH D/A INTERFACE 5 RF 14 BIAS 15 DIGITAL OUT 39 DOUT 38 C4M 6 16K RAM ASYO 17 ASYE 18 ERROR CORRECTOR 3 37 FSTT 36 XTSL 35 XTAO 34 XTAI 33 MNTO • F SET + 47 SQCK EFM DEMODULATOR DIGITAL PLL WDCK 19 TG2 DFCT – – 13 TA O – TDFCT 47 AVSS 11 CLTV 12 48 MUTE DIGITAL CLV 46 SQSO ASYI 16 + TM1 TZC 46 FS4 + TG2 FSET TA M VDD GFS MNT1 TGU MNT3 SRCH – 81 – XROF 12 RFCK 11 CZPO 10 XPCK 9 XUGF 8 GTOP 7 BCLK 6 PCMD 5 FE M FDFCT 4 FE O 3 FLB 2 FGD 1 FEI 20 21 22 23 24 25 26 27 28 29 30 31 32 FEO VC 48 14 SL P TM2 DFCT • WINDOW COMP PCO 9 VSS 10 AVDD 13 TM3 TEI 44 ATSC 45 15 SL M TM4 – SUB CODE PROCESSOR 4 LRCK TOG2 TOG1 + TM5 + CPU INTERFACE 14 51 DATA 50 XRST 49 SENS 5 LOCK 5 TEST 6 FILO 7 VEE 41 TEO 42 SERVO AUTO SEQUENCER FOK 1 MON 2 MDP 3 CLOCK GENERATOR + – BAL3 BAL2 BAL1 TE AMP + – – – + E IV AMP EI 40 – 82 – OP-OUT 14 GND 13 OUT2B 12 OUT2A 11 9 IN2A XRST REG 0 20 XLT IIL – + TR-B • INPUT SHIFT RESISTOR IN1B • IIL DATA RESISTOR TTL IN1A 21 DATA FE BIAS 37 IN2B 10 8 GND 7 6 5 2 OUT1B 3 1 OUT1A + TTL RF IV AMP2 F 38 DRIVE BUFFER 22 XRST 4 – + LEVEL SHIFT – + – – + + LEVEL SHIFT DRIVE BUFFER IC104 PCM1710U-B LRCIN 1 28 ML/DSD INPUT INTERFACE DIN 2 DIGITAL FILTER MODE CONTROL BCKIN 3 26 MD/DM1 TIMING CONTROL 4 CLKO 27 MC/DM2 25 MUTE XTI 5 24 MODE XTO 6 23 CKSL NOISE SHAPER DGND 7 22 DGND VDD 8 21 VDD 5-LEVEL DAC RIGHT 5-LEVEL DAC LEFT LOW-PASS FILTER RIGHT LOW-PASS FILTER LEFT VCC2R 9 GND2R 10 EXT1R 11 19 GND2L 18 EXT1L 3-STAGE AMP LEFT 3-STAGE AMP RIGHT EXT2R 12 VOUTR 13 17 EXT2L 16 VOUTL 15 VCC1 GND1 14 – MD Section – IC153 LB1830-S-TE-L VD TST1 TST2 TST3 DEM1 DEM0 MCLK VREF DGND VCONT 6 PWDA IC201 AK4520A-VF-E2 VREF 7 PWAD VM 8 CMODE IN1 9 VCOM AOUTR AOUTL IN2 10 20 VCC2L 28 27 26 25 24 23 22 21 20 19 18 17 16 15 LOGIC PREDRIVER LPF ∆Σ MODULATOR 8× INTERPOLATOR LPF ∆Σ MODULATOR 8× INTERPOLATOR COMMON VOLTAGE DECIMATION FILTER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 DIF0 DIF1 LRCK SCLK SDTI SDTO OUT1 VS AGND GND ∆Σ MODULATOR VA OUT2 5 AINL+ AINL– VCC 4 DECIMATION FILTER AINR– 3 ∆Σ MODULATOR AINR+ 2 SERIAL I/O INTERFACE VREFH VREFL 1 CLOCK DIVIDER – 83 – – + RF AGC RF PEAK 44 43 42 41 40 39 38 37 USROP RF AGC + – EQ USRC DET + – RFA1 AGCI 45 COMPO OPN 46 COMPP RFO 47 ADDC MORFI 48 OPO MORFO IC101 CXA2523AR EQ BPF3T RFA2 I 1 J 2 –1 – –2 – HLPT –1 –2 CFST CVB A 3 IVR WBL TEMP PEAK –2 BOTTOM GRVA 36 BOTM PBH –1 GRV + – 4 3T PTGR – 1 – –2 – + VC PEAK3T P-P 3T WBL 34 FE + + + + AA 35 ABCD 33 AUX BPFC ABCDA 32 ADFG B + – 5 IVR C 31 ADAGC BB + – 6 IVR + + – – 30 ADIN FEA CC DET BPF22 D – – + + + – 7 IVR ADIP AGC WBL ATA DD WBL E + – 8 IVR 29 ADFM EE + – EE' –1 PTGR – + – + –2 –1 TESW –2 + – 9 IVR FF + – TG 3T 25 WBLADJ VI CONV EQ AUXSW PD 10 BGR + – COMMAND + – VREF SCRI - PARA DECODE APC 11 26 TE TEA WBL FF' FBAL GSW IV 28 SE SEA 27 CSLED EFB F TG 14 15 16 17 18 19 20 21 22 23 24 TEMPI TEMPR SWDT SCLK XLAT XSTBY F0CNT VREF EQADJ VCC – 84 – 3TADJ 13 GND APCREF 12 MNT1 2 MONITOR CONTROL MNT2 3 DCHG APC ADFG F0CNT XLRF CKRF DTRF APCREF LDDR TRDR TFDR DVDD FFDR 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 PWM GENERATOR SPINDLE SERVO MNT0 1 KRDR FS4 SRDR SFDR SPRD 94 93 AUTO SEQUENCER 100 99 98 97 96 95 SPFD TEST0 TEST1 TEST2 TEST3 DVSS EFMO IC121 CXD2652AR EACH BLOCK 75 AUX2 74 TE 73 SE 72 AVSS MNT3 4 71 ADRB ADIP DEMODULATOR/ DECODER SWDT 5 70 ADRT 69 AVDD 68 ADIO SCLK 6 EACH BLOCK CPU I/F XLAT 7 SRDT 8 67 VC SERVO DSP SENS 9 A/D CONVERTER 66 AUX1 65 FE ANALOG MUX XRST 10 64 ABCD APC SQSY 11 63 BOTM 62 PEAK SUBCODE PROCESSOR DQSY 12 61 CLTV RECP 13 PLL 60 FILO EFM/ACIRC ENCODER/ DECODER SHOCK RESISTANT MEMORY CONTROLLER XINT 14 59 FILI 58 PCO 57 PDO TX 15 56 AVSS OSCI 16 CLOCK GENERATOR OSCO 17 XTSL 18 EACH BLOCK DIGITAL AUDIO I/F RVDD 19 RVSS 20 55 RFI COMP SAMPLING RATE CONVERTER 54 BIAS 53 AVDD DIN 21 52 ASYI DOUT 22 51 ASYO ADDT 23 ATRAC ENCODER/DECODER DADT 24 DRAM LRCK 25 ADDRESS/DATA BUS A00 - A11, D0 - D3 CAPA– CAPA+ IN2R IN2F VM2 OUT2F PGND2 OUT2R VM12 OUT1R PGND1 OUT1F VM1 IN1F IN1R VDD IC152 BH6511FS-E2 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 AMP AMP INTERFACE PREDRIVE PREDRIVE PREDRIVE PREDRIVE 3 4 5 6 7 8 9 10 11 12 IN4R IN4F VM4 OUT4F PGND4 OUT4R VM34 OUT3R PGND3 OUT3F PSB 13 14 15 16 PSB 2 INTERFACE IN3R 1 VG AMP GND AMP IN3F AMP AMP INTERFACE VDD VM3 CHARGE PUMP. OSC AMP AMP INTERFACE – 85 – 50 MVCI D3 D2 D0 D1 XWE XRAS A09 XCAS XOE DVSS A11 A08 A07 A06 A05 A04 A10 A01 A00 A03 A02 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 DVDD FS256 XBCK 26 27 28 – MAIN Section – IC570 LA5620 PH5 IC603 M62016L 1 STBY 2 VCC ANA5 3 4 SYS3.3 5 BACK 6 AC 7 CD1 8 P. DOWN 9 – + – + – + – + – + CD2 11 DELAY CIRCUIT – + 2 3 4 5 RESET CD VCC IC801 LB1641 O.C.P MOTOR DRIVE MOTOR DRIVE 3 4 5 6 7 8 9 MOTOR DRIVE NOISE FILTER CLAMP FWD.IN REV.IN VCC 1 VCC 2 NOISE FILTER 10 MOTOR DRIVE 2 GND FWD/REV/STOP CONTROL LOGIC 1 RESET SIGNAL GENERATING BLOCK INT VREF T.S.D COM + – 1 GND 10 S. RESET 12 INTERRUPT SIGNAL GENERATING BLOCK GND 3.3V DELAY CIRCUIT COM + – – 86 – – AUDIO Section – RDCL TS7 OSCO OSCI VDDD VSSD TEST TSTLD IC1500 BU1922F 16 15 14 13 12 11 10 9 TEST LOGIC AND OUTPUT SELECTOR SWITCH QUALITY BIT GENERATOR OSCILLATOR AND DIVIDER DEFFERENTIAL DECODER BIPHASE SYMBOL DECODER RECONSTRUCTION FILTER 57kHz BANDPASS (8th ORDER) ANTIALIASING FILTER CONTAS LOOP VARIABLE AND FIXED DIVIDER CLOCKED COMPARATOR CLOCK REGENERATION AND SYNC VP1 4 5 RDDA Vref MUX VDDA 6 7 8 SCOUT 3 CIN 2 VSSA 1 QUAL REFERENCE VOLTAGE – 87 – 7-27. IC PIN FUNCTIONS • IC101 CXA2523AR (RF Amplifier) (BD (MD) Board) Pin No. 1 2 3 4 to 9 Pin Name I I/O I Function I-V converted RF signal I input from the optical pick-up block detector J I I-V converted RF signal J input from the optical pick-up block detector VC O Middle point voltage (+1.65V) generation output terminal A to F I Signal input from the optical pick-up detector 10 PD I Light amount monitor input terminal 11 APC O Laser amplifier output terminal to the automatic power control circuit 12 APCREF 13 GND 14 TEMPI I 15 TEMPR O Output terminal for a temperature sensor reference voltage 16 SWDT I Writing serial data input from the CXD2652AR (IC121) 17 SCLK I Serial clock signal input from the CXD2652AR (IC121) 18 XLAT I Serial latch signal input from the CXD2652AR (IC121) 19 XSTBY I I — Reference voltage input terminal for setting laser power Ground terminal Connected to the temperature sensor Standby signal input terminal “L”: standby (fixed at “H” in this set) Center frequency control voltage input terminal of internal circuit (BPF22, BPF3T, EQ) 20 F0CNT I 21 VREF O Reference voltage output terminal 22 EQADJ I Center frequency setting terminal for the internal circuit (EQ) 23 3TADJ I Center frequency setting terminal for the internal circuit (BPF3T) 24 VCC 25 WBLADJ I Center frequency setting terminal for the internal circuit (BPF22) 26 TE O Tracking error signal output to the CXD2652AR (IC121) 27 CSLED I Connected to the external capacitor for low-pass filter of the sled error signal 28 SE O Sled error signal output to the CXD2652AR (IC121) 29 ADFM O FM signal output of the ADIP 30 ADIN I Receives a ADIP FM signal in AC coupling 31 ADAGC I Connected to the external capacitor for ADIP AGC 32 ADFG O ADIP duplex signal (22.05 kHz ± 1 kHz) output to the CXD2652AR (IC121) 33 AUX O Auxiliary signal (I3 signal/temperature signal) output to the CXD2652AR (IC121) 34 FE O Focus error signal output to the CXD2652AR (IC121) 35 ABCD O Light amount signal (ABCD) output to the CXD2652AR (IC121) 36 BOTM O Light amount signal (RF/ABCD) bottom hold output to the CXD2652AR (IC121) 37 PEAK O Light amount signal (RF/ABCD) peak hold output to the CXD2652AR (IC121) 38 RF O Playback EFM RF signal output to the CXD2652AR (IC121) 39 RFAGC I Connected to the external capacitor for RF auto gain control circuit 40 AGCI I Receives a RF signal in AC coupling 41 COMPO O User comparator output terminal Not used (open) 42 COMPP I User comparator input terminal 43 ADDC I Connected to the external capacitor for cutting the low band of the ADIP amplifier 44 OPO O User operational amplifier output terminal 45 OPN I User operational amplifier inversion input terminal 46 RFO O RF signal output terminal 47 MORFI I Receives a MO RF signal in AC coupling 48 MORFO O MO RF signal output terminal — input from the CXD2652AR (IC121) Not used (open) Power supply terminal (+3.3V) – 88 – Not used (fixed at “L”) Not used (open) Not used (fixed at “L”) • IC121 Digital Signa; Processor, Digitak Servo Signal Processor, EFM/ACIRC Encoder/Decoder, Shock-proof Memory Controller, ATRAC Encoder/Decoder, 2M Bit DRAM (CXD2652R) (BD (MD) Board) Pin Name Pin No. I/O Function Focus OK signal output to the MD system controller (IC316) 1 MNT0 (FOK) O 2 MNT1 (SHCK) O Track jump detection signal output to the MD system controller (IC316) 3 MNT2 (XBUSY) O Monitor 2 signal output to the MD system controller (IC316) 4 MNT3 (SLOC) O Monitor 3 signal output to the MD system controller (IC316) 5 SWDT I Writing data signal input from the MD system controller (IC316) 6 SCLK I Serial clock signal input from the MD system controller (IC316) 7 XLAT I Serial latch signal input from the MD system controller (IC316) 8 SRDT O (3) Reading data signal output to the MD system controller (IC316) 9 SENS O (3) Internal status (SENSE) output to the MD system controller (IC316) 10 XRST I 11 SQSY O 12 DQSY O 13 RECP I 14 XINT O 15 TX I 16 OSCI I 17 OSCO O “H” is output when focus is on Reset signal input from the MD system controller (IC316) “L”: reset Subcode Q sync (SCOR) output to the MD system controller (IC316) “L” is output every 13.3 msec Almost all, “H” is output Digital In U-bit CD format subcode Q sync (SCOR) output to the MD system controller (IC316) “L” is output every 13.3 msec Almost all, “H” is output Laser power selection signal input from the MD system controller (IC316) “H”: recording mode, “L”: playback mode Interrupt status output to the MD system controller (IC316) Recording data output enable signal input from the MD system controller (IC316) Writing data transmission timing input (Also serves as the magnetic head on/off output) System clock signal (512Fs=22.5792 MHz) input terminal System clock signal (512Fs=22.5792 MHz) output terminal Input terminal for the system clock frequency setting “L”: 45.1584 MHz, “H”: 22.5792 18 XTSL I 19 RVDD — Power supply terminal (+3.3V) (digital system) 20 RVSS — Ground terminal (digital system) 21 DIN I Digital audio signal input terminal when recording mode (for optical in) 22 DOUT O Digital audio signal output terminal when playback mode (for optical out) 23 ADDT I Recording data input from the A/D, D/A converter (IC201) 24 DADT O Playback data output to the A/D, D/A converter (IC201) 25 LRCK O L/R sampling clock signal (44.1 kHz) output to the A/D, D/A converter (IC201) 26 XBCK O Bit clock signal (2.8224 MHz) output to the A/D, D/A converter (IC201) 27 FS256 O Clock signal (11.2896 MHz) output to the A/D, D/A converter (IC201) 28 DVDD — Power supply terminal (+3.3V) (digital system) 29 A03 O 30 A02 O 31 A01 O 32 A00 O 33 A10 O 34 A04 O 35 A05 O 36 A06 O 37 A07 O 38 A08 O 39 A11 O MHz (fixed at “H” in this set) Address signal output to the external D-RAM (IC124) * I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O. – 89 – Not used Pin No. 40 DVSS Pin Name I/O — Ground terminal (digital system) Function 41 XOE O Output enable signal output to the external D-RAM (IC124) 42 XCAS O Column address strobe signal output to the external D-RAM (IC124) 43 A09 O Address signal output to the external D-RAM (IC124) 44 XRAS O Row address strobe signal output to the external D-RAM (IC124) 45 XWE O Write enable signal output to the external D-RAM (IC124) 46 D1 I/O 47 D0 I/O 48 D2 I/O 49 D3 I/O 50 MVCI I Digital in PLL oscillation input from the external VCO 51 ASYO O Playback EFM full-swing output 52 ASYI I (A) 53 AVDD — 54 BIAS I (A) Playback EFM asymmetry circuit constant current input 55 RFI I (A) Playback EFM RF signal input from the CXA2523AR (IC101) 56 AVSS — 57 PDO O (3) 58 PCO O (3) Phase comparison output for master clock of the recording/playback EFM master PLL 59 FILI I (A) Filter input for master clock of the recording/playback master PLL 60 FILO O (A) Filter output for master clock of the recording/playback master PLL 61 CLTV I (A) Internal VCO control voltage input of the recording/playback master PLL 62 PEAK I (A) Light amount signal (RF/ABCD) peak hold input from the CXA2523AR (IC101) 63 BOTM I (A) Light amount signal (RF/ABCD) bottom hold input from the CXA2523AR (IC101) 64 ABCD I (A) Light amount signal (ABCD) input from the CXA2523AR (IC101) 65 FE I (A) Focus error signal input from the CXA2523AR (IC101) 66 AUX1 I (A) Auxiliary signal (I3 signal/temperature signal) input from the CXA2523AR (IC101) 67 VC I (A) Middle point voltage (+1.65V) input from the CXA2523AR (IC101) 68 ADIO O (A) Monitor output of the A/D converter input signal 69 AVDD — Power supply terminal (+3.3V) (analog system) 70 ADRT I (A) 71 ADRB I (A) 72 AVSS — 73 SE I (A) Sled error signal input from the CXA2523AR (IC101) 74 TE I (A) Tracking error signal input from the CXA2523AR (IC101) 75 AUX2 I (A) Auxiliary signal input terminal 76 DCHG I (A) Connected to the +3.3V power supply 77 APC I (A) Error signal input for the laser automatic power control 78 ADFG I ADIP duplex FM signal (22.05 kHz ± 1 kHz) input from the CXA2523AR (IC101) 79 F0CNT O Filter f0 control signal output to the CXA2523AR (IC101) 80 XLRF O Serial latch signal output to the CXA2523AR (IC101) 81 CKRF O Serial clock signal output to the CXA2523AR (IC101) 82 DTRF O Writing data output to the CXA2523AR (IC101) Two-way data bus for the external D-RAM (IC124) Not used (fixed at “L”) Playback EFM asymmetry comparator voltage input Power supply terminal (+3.3V) (analog system) Ground terminal (analog system) Phase comparison output for clock playback analog PLL of the playback EFM Not used (open) Not used (open) A/D converter operational range upper limit voltage input terminal (fixed at “H” in this set) A/D converter operational range lower limit voltage input terminal (fixed at “L” in this set) Ground terminal (analog system) Not used (fixed at “H”) * I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O. – 90 – Not used (fixed at “L”) Pin Name Pin No. I/O Function Control signal output to the reference voltage generator circuit for the laser automatic 83 APCREF O 84 LDDR O PWM signal output for the laser automatic power control 85 TRDR O Tracking servo drive PWM signal (–) output to the BH6511FS (IC152) 86 TFDR O Tracking servo drive PWM signal (+) output to the BH6511FS (IC152) 87 DVDD — Power supply terminal (+3.3V) (digital system) 88 FFDR O Focus servo drive PWM signal (+) output to the BH6511FS (IC152) 89 FRDR O Focus servo drive PWM signal (–) output to the BH6511FS (IC152) 90 FS4 O Clock signal (176.4 kHz) output terminal (X’tal system) Not used (open) 91 SRDR O Sled servo drive PWM signal (–) output to the BH6511FS (IC152) 92 SFDR O Sled servo drive PWM signal (+) output to the BH6511FS (IC152) 93 SPRD O Spindle servo drive PWM signal (–) output to the BH6511FS (IC152) 94 SPFD O Spindle servo drive PWM signal (+) output to the BH6511FS (IC152) 95 FGIN I 96 TEST1 I 97 TEST2 I 98 TEST3 I 99 DVSS — Ground terminal (digital system) 100 EFMO O EFM signal output terminal when recording mode power control Input terminal for the test (fixed at “L”) – 91 – Not used (open) • IC316 M30610MCA-272FP (MD SYSTEM CONTROL) (BD (MD) BOARD) Pin No. 1,2 3,4 Pin Name (JOG0, JOG1) I/O I Function Not used (fixed at “H”) Encoder switch signal input terminal DAOUT1, DAOUT2 O Not used (fixed at “L”) 5 SQSY I Subcode Q sync (SCOR) input from the CXD2652AR (IC121) 6 REMCON I Remote control signal input 7 EMP O De-emphasis control signal output to the AK4520 (IC201) 8 BYTE I External data bus line byte select signal input terminal “L”:16bit “H”: 8bit (fixed at “L”) 9 CNVSS I Processor mode select signal input terminal (fixed at “L”) 10 XIN-T I Sub system clock input tarminal Not used (fixed at “L”) 11 (XOUT-T) O Sub sytem clock output tarminal Not used (fixed at “L”) 12 SYSTEM-RST I MD reset signal input from the M62016 (IC603) 13 XOUT O Main system clock signal output terminal 14 GND — Ground terminal 15 XIN I 16 +3V — Power supply terminal (+3.3V) 17 NMI — Connecting to power supply 18 AMUTE — Not used (fixed at "L") 19 PWR-DWN O Power down detect signal output to the LA5620 (IC570) 20 DQSY I Digital in U-bit CD format subcode Q sync (SCOR) input from theCXD2652SAR (IC121) 21 STB I Stand-by signal input terminal 22 DA-RST I D/A converter reset signal input terminal 23 XINT I Interrupt status input from the CXD2652AR (IC121) 24 DA-EN O D/A converter enable signal output to the AK4520 (IC201) 25 AD-EN O A/D converter enable signal output to the AK4520 (IC201) 26 MEC-BUSY O Mecha-busy signal output to the master control (IC601) 27 FLCS O Display clear signal output terminal 28 FLCLK O Display data clock signal output terminal 29 — — Not used (fixed at “L”) 30 FLDATA O Display data signal output terminal 31 TXD O MD control data signal output to the master control (IC601) 32 RXD I MD control data signal input to the master control (IC601) 33 CLK I MD control data clock signal input to the master control (IC601) 34 MAS-BUSY I Master-busy signal input from the master control (IC601) 35 SWDT O Writing data signal output to the CXD2652AR (IC121) 36 SRDT I Reading data signal input from the CXD2652AR (IC121) 37 SCLK O Serial clock signal output to the CXD2652AR (IC121) 38 XLAT O Serial latch signal output to the CXD2652AR (IC121) 39 — O Clock signal output terminal 40 DIG-RST O Reset signal output enable signal output to the CXD2652AR (IC121) 41 SENS I Status (SENSE) input from the CXD2652AR (IC121) 42 SCTX O Recording data output enable signal output to the CXD2652AR (IC121) 43 XINT O Not used (fixed at “L”) 44 WRPWR O Laser power selection signal output to the CXD2652AR (IC121) 45 MNT3 I Monitor 3 signal input from the CXD2652AR (IC121) 46 MNT2 I Monitor 2 signal input from the CXD2652AR (IC121) 47 MNT1 I Track jump detection signal input from the CXD2652AR (IC121) 48 MNTO I Focus OK signal input from the CXD2652AR (IC121) 49 LDON O Laser diode ON signal output terminal 50 MOD O HF module ON signal output terminal Main sytem clock signal input terminal – 92 – Not used (fixed at “L”) Not used (fixed at “L”) Not used (fixed at “L”) Not used (fixed at “L”) Not used (fixed at “L”) Not used (fixed at “L”) LDIN I/O O Function MD loading-in signal output to LB1830M (IC153) 52 LDOUT O MD loading-out signal output to LAB1830M (IC153) 53 LD-LOW O Loading motor voltage control signal output to the loading motor driver 54 PROTECT I MD PROTECT switch (S683) detect signal input terminal 55 REFLECT I MD REFLECT switch (S682) detect signal input terminal 56 PACK-IN I Not used 57 PACK-OUT I MD PACK OUT switch (S686) detect signal input terminal 58 CHUCK-IN I MD CHUCKING IN switch (S685) detect signal input terminal 59 LIMIT-IN I MD LIMIT IN switch (S681) detect signal input terminal 60 REC. P I MD REC POSITION switch (S688) detect signal input terminal 61 PB. P I MD PB POSITION switch (S687) detect signal input terminal 62 +5V — Power supply (+5V) 63 — — Not used (fixed at “L”) 64 GND — Ground terminal 65 to 72 — — Connect terminal 65 to 72 73 to 78 — — Not used (fixed at “L”) 79 SDA I/O Tow-way data bus for the EEPROM (IC171) 80 SCL O Clock signal output to the EEPROM (IC171) Not used (fixed at “L”) Pin No. 51 81, 82 Pin Name Not used (fixed at “L”) — — POWER — 84, 85 — — 86, 87 — — Not used (fixed at “L”) 88 to 90 — — Connect terminal 88 to 90 Not used (fixed at “L”) Not used (fixed at “H”) 83 91 to 93 Conenct terminal 83 to 85 KEY0, KEY1, KEY2 — Connect terminal 91 to 93 94 — — Not used (fixed at “L”) 95 SOURCE — Not used (fixed at “L”) 96 AVSS — Ground terminal 97 — — Not used (fixed at “L”) 98 VREF5V — Power supply (+5V) 99 3.3V — Power supply (+3.3V) 100 — — Not used (fixed at “L”) – 93 – Not used (fixed at “L”) • IC601 µPD78078GF-062-3BA (MASTER CONTROL) (MAIN BOARD (1/3)) Pin Name I/O I Function Pin No. 1 to 3 VER 4 VER I 5 to 7 (NC) — Not used 8 — — Not used (open) 9 IC — Connecting to ground 10 X2 O Main system clock output terminal (5 MHz) 11 X1 I Main system clock input terminal (5 MHz) 12 VDD — 13 XT2 O Sub system clock output terminal (32 kHz) 14 XT1 I Sub system clock input terminal (32 kHz) 15 RESET I System reset signal input from the reset signal generator (IC602) 16 AU-BUS IN I AU-BUS signal input terminal 17 AU-BUS OUT O AU-BUS signal output terminal 18 ENC/A I Encorder volume signal A input from the master volume (S901) 19 ENC/B I Encoder volume signal B input from the master volume (S901) 20 RDS/CLK I RDS clock signal input from the RDS demodulator (IC1500) 21 RDS/DATA I RDS data signal input from the RDS demodulator (IC1500) 22 SCOR (BD) 23 AVDD — 24 AVREF0 — 25 KEY0 I 26 KEY 1 I 27 KEY 2 I I Destination setting terminal Destination setting terminal Not used (open) Power supply terminal (+5V) Sub-code sync S0, S1 detect signal input from the digital signal processor (IC103) Power supply terminal (+5V) (for A/D converter) Reference voltage input terminal (+5V) (for A/D converter) Key input terminal (A/D input) POWER key (S902) input Key input terminal (A/D input) p (CD), ^ (CD), § (CD), p (MD), ^ (MD), § (MD) keys (S903 to S908) input Key input terminal (A/D input) FUNCTION, ) + +, TUNER/BAND, = 0 –, r REC, CD-MD SYNC, REPEAT STEREO/MONO, PLAY MODE TUNING MODE (S909 to S916) input 28 to 30 31 — RTS (TO MD. CTS) — Not used O Master-busy signal output to the MD system control (IC316) MD power on/off signal output to the MD power regulator (IC570) MASTER BUSY 32 MD-POWER O 33 AVSS — 34 POWER ON I 35 MD OEM/REST O MD reset signal output terminal 36 AVREF1 I Reference voltage input terminal (+5V) (for A/D converter) I MD control data signal input from the MD system control (IC316) O MD control data signal output to the MD system control (IC316) 37 38 RXD (TO MD. TXD) RXD TXD (TO MD. RXD) Ground terminal (for A/D converter) System power on signal input terminal TXD 39 MD-CLK O MD control data clock signal output to the MD system control (IC316) 40 VSS CTS (TO MD. RTS) — Ground terminal 41 MECHA BUSY I Mecha-busy signal input from the MD system control (IC316) 42 FL/DRIV DATA O Display data signal output to the fluorescent indicator drive (IC901) 43 FL/DRIV CLOCK O Display data clock signal output to the fluorescent indicator drive (IC901) 44 FL/DRIV CS O Display clear signal output to the fluorescent indicator drive (IC901) “L”: data output 45 FL/DRIVE RESET O Display reset signal output to the fluorescent indicator drive (IC901) “L”: reset 46 BD SUBQ I Sub-code Q data signal input from the CXD2507AQ (IC103) 47 (NC) — Not used (open) – 94 – Pin No. 48 Pin Name BD SQCLK I/O O Function Sub-code Q data reading clock signal output to the CXD2507AQ (IC103) 49 BD CLOCK O Serial data clock signal output to the CXD2507AQ (IC103) 50 BD DATA O Serial data output to the CXD2507AQ (IC103) 51 XLT O Serial data latch pulse signal output to the CXD2507AQ (IC103) 52 PRGL (DF. LAT) O Serial data latch pulse signal output to the PCM1710U (IC104) 53 SENCE I Internal status (SENSE) signal input from the CXD2507AQ (IC103) 54 ADJ I Test mode input terminal 55 IN-SW I Disc tray close complete signal input terminal “L”: Completed 56 OUT-SW I Disc tray open complete signal input terminal “L” Completed 57 LOAD-OUT O Disc tray loading out signal output to the motor driver (IC801) 58 LOAD-IN O Disc tray loading in signal output to the motor driver (IC801) 59 FOCUS-SW O Focus gain selection switch signal output terminal 60 BD-REST O BD block reset signal output terminal 61 CD-POWER O CD power on/off signal output to the CD power regulator (Q561, 562) 62 ST-POWER O ST power on/off signal output terminal 63 D. IN. SELECT O Optical/CD select signal output terminal — — Not used 64, 65 “H’: normal (fixed at “H” in this set) “L”: normal “H”: down “L”: reset Not used (open) “H”: optical “L”: CD 66 LED-CD. DISC O CD INDICATOR LED (D908) drive signal output terminal 67 LED-MD. DISC O MD INDICATOR LED (D905) drive signal output terminal 68 LED-MD. REC O r LED (D904) drive signal output terminal 69 LED-CD. PAUSE O P (CD) LED (D907) drive signal output terminal 70 LED-CD. PLAY O ( (CD) LED (D906) drive signal output terminal 71 VSS — Ground terminal 72 LED-MD. PAUSE O P (MD) LED (D903) drive signal output terminal 73 LED-MD. PLAY O ( (MD) LED (D902) drive signal output terminal 74 DBFB O DBFB on/off signal output terminal 75 RECOUT. MUTE O Rec mute (tape) signal output terminal “L”: mute 76 MUTE O Mute signal output terminal 77 ATT/6DB O Tape input level attenuate signal output terminal 78 SOUND/IC DATA O Graphic equalizer data signal output to the M62428FP (IC701) 79 SOUND/IC CLOCK O Graphic equalizer data clock signal output to the M62428FP (IC701) 80 SOUND/IC LAT O Graphic equalizer data latch pulse signal output to the M62428FP (IC701) 81 (GND) — Ground terminal 82 ST STEREO I Stereo detection signal input from the tuner 83 ST TUNED I Tuned detection signal input from the tuner 84 ST DATA-IN I Data signal input from the tuner 85 ST DATA-OUT O Data signal output to the tuner 86 ST CLOCK O Data transfer clock signal output to the tuner 87 ST CE O Chip enable signal output to the tuner 88 ST MUTE O Mute signal output to the tuner 89 FM/AM SELECT O FM/AM select signal output 90 SIRCUS I Remote control signal input from the remote control receiver (IC902) 91 — — Not used (open) 92 — — Connecting to ground 93 FAN SPEED O Fan speed control signal output terminal 94 FAN STOP O Fan on/off signal output terminal — — 95 to 99 100 BACKUP I “L”: on Not used (open) Not used (open) Not used (open) Connecting to ground System reset signal input from the reset signal generator (IC602) – 95 – SECTION 8 EXPLODED VIEWS NOTE: • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The mechanical parts with no reference number in the exploded views are not supplied. • Hardware (# mark) list and accessories and packing materials are given in the last of this parts list. The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. • Abbreviation CND : Canadian model EE : East European model HK : Hong Kong model SP : Singapore model MY : Malaysia model AR : Argentine model AUS : Australian model JE : Tourist model Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. 8-1. FRONT PANEL SECTION 3 12 11 8 8 5 not supplied 7 12 8 10 13 FL901 9 15 not supplied 14 6 2 supplied with S901 1 #4 Ref. No. Part No. Description 1 2 * 3 4 * 5 4-210-901-01 4-210-903-01 4-993-842-01 X-4950-225-1 1-671-020-21 KNOB (VOL) ORNAMENT (VOL) CASE PANEL ASSY, FRONT HP BOARD * 6 * 7 8 * 9 4-930-336-71 1-670-745-21 4-951-620-01 A-4417-317-A FOOT (FELT) MD LED BOARD SCREW (2.6X8), +BVTP PANEL BOARD, COMPLETE 4 Remark Ref. No. 10 11 12 * 13 14 15 15 FL901 – 96 – Part No. Description 1-782-793-11 WIRE (FLAT TYPE) (23 CORE) 4-210-902-01 3-363-099-11 4-993-866-21 4-212-098-01 4-210-890-11 PANEL, LOADING SCREW (CASE 3 TP2) HOLDER (FL) FILTER WINDOW (FL)(AEP,UK,EE) 4-210-890-21 WINDOW (FL)(EXCEPT AEP,UK,EE) 1-517-687-11 INDICATOR TUBE, FLUORESCENT Remark 8-2. CHASSIS SECTION not supplied #4 #4 #2 #2 57 #2 not supplied 58 FAN901 56 54 #4 60 55 T1600 not supplied #2 59 B #1 MDM-3J not supplied 70 not supplied C 61 #1 #3 rA 53 62 rB 67 CDM13C-5BD19 #4 #4 US,CND #2 C A 65 66 #1 51 not supplied 63 64 B 52 CNP1601 CNP1601 (including rA, rB) 68 MY, SP, JE CNP1601 UK,HK 69 A AUS AR CNP1601 EXCEPT US,CND,AR #4 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description 51 52 53 * 54 * 55 4-993-867-01 1-782-990-11 3-703-244-00 1-666-904-11 A-4417-126-A FOOT (8) WIRE (FLAT TYPE) (19 CORE) BUSHING (2104), CORD TRANS BOARD POWER AMP BOARD, COMPLETE (AEP,UK,EE) * 55 * 55 56 * 57 * 57 A-4417-130-A POWER AMP BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS) A-4417-134-A POWER AMP BOARD, COMPLETE (US,CND) 1-782-991-11 WIRE (FLAT TYPE) (15 CORE) A-4414-823-A JACK BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS) A-4414-826-A JACK BOARD, COMPLETE (US,CND) * 67 ! 68 * 57 58 * 59 * 59 * 59 A-4414-830-A 4-985-672-01 4-993-849-52 4-993-849-61 4-993-849-71 ! 69 1-770-019-11 * 70 4-988-533-01 ! CNP1601 1-696-847-11 ! CNP1601 1-769-744-11 ! CNP1601 1-783-532-11 ADAPTOR, CONVERSION PLUG 3P (UK,HK) HOLDER, PWB CORD, POWER (AUS) CORD, POWER (EXCEPT US,CND,AR,AUS) CORD, POWER (US,CND) * 60 * 61 62 62 1-666-905-11 4-984-203-21 1-233-544-21 1-233-546-21 ! CNP1601 1-783-941-11 FAN901 1-698-997-11 ! T1600 1-431-498-11 ! T1600 1-431-988-11 ! T1600 1-431-989-11 CORD, POWER (AR) FAN, D.C. TRANSFORMER, POWER (MY,SP,JE,HK,AR,AUS) TRANSFORMER, POWER (AEP,UK,EE) TRANSFORMER, POWER (US,CND) 62 Remark Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. JACK BOARD, COMPLETE (AEP,UK,EE) SCREW (+PTPWHM2.6), FLOATING PANEL, BACK (AEP,UK,EE) PANEL, BACK (MY,SP,JE,HK,AR,AUS) PANEL, BACK (US,CND) ST TERMINAL BOARD PLATE (ST-A), SHIELD ENCAPSULATED COMPONENT (US,CND) ENCAPSULATED COMPONENT (MY,SP,JE,HK,AR,AUS) 1-693-387-21 TUNER (FM/MW/LW)(AEP,UK,EE) Ref. No. Part No. Description * 63 64 * 65 * 65 * 65 4-984-204-11 1-783-213-11 A-4417-124-A A-4417-128-A A-4417-132-A PLATE (ST-B), SHIELD WIRE (FLAT TYPE) (15 CORE) MAIN BOARD, COMPLETE (AEP,UK,EE) MAIN BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS) MAIN BOARD, COMPLETE (US,CND) * 66 * 67 * 67 4-924-098-91 HOLDER, PC BOARD A-4414-818-A AUDIO BOARD, COMPLETE (AEP,UK,EE) A-4414-821-A AUDIO BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS) A-4414-824-A AUDIO BOARD, COMPLETE (US,CND) 1-569-008-21 ADAPTOR, CONVERSION 2P (MY,SP,JE) – 97 – Remark 8-3. MD MECHANISM DECK SECTION-1 (MDM-3J) not supplied #5 #5 108 108 107 107 not supplied 106 105 109 104 103 102 110 101 #6 Ref. No. Part No. Description * 101 102 103 104 105 A-4699-808-A 1-660-966-11 1-782-683-11 X-4949-900-1 4-997-456-02 BD (MD) BOARD, COMPLETE OP RELAY FLEXIBLE BOARD WIRE (FLAT TYPE) (14 CORE) SHUTTER ASSY SHAFT (SHUTTER)(A) Remark Ref. No. 106 107 108 109 110 – 98 – Part No. Description 4-986-959-01 4-987-327-01 4-628-167-01 4-997-962-01 1-783-113-11 WASHER, STOPPER INSULATOR SCREW, STEP SPRING (O/C), TENSION WIRE (FLAT TYPE) (25 CORE) Remark Ver 1.1 2001.06 8-4. MD MECHANISM DECK SECTION-2 (MDM-3J) 155 152 #5 156 153 154 173 #5 159 171 158 151 160 157 #7 #13 172 #7 161 not supplied 155 162 M902 M903 164 M901 166 163 155 165 168 HR901 170 167 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. #8 Ref. No. Part No. Description 151 * 152 153 154 155 A-4672-138-A 4-983-439-01 3-953-235-01 4-979-901-21 3-342-375-11 156 157 158 159 160 4-979-890-11 4-979-898-01 4-979-899-01 4-979-897-01 4-979-885-01 161 162 * 163 169 Ref. No. Part No. Description SLIDER COMPLETE ASSY BRACKET (DAMPER) DAMPER, OIL LEVER (LIMITTER) SCREW (M1.7X1.4), SPECIAL 164 165 166 ! 167 168 A-3304-200-A 4-963-914-02 3-366-890-11 8-583-028-02 4-987-061-01 SCREW ASSY , LEAD RACK (INSER TER) SCREW (M1.4) OPTICAL PICK-UP KMS-260A/J1N (for MD) SPACER (RACK) RET AINER (GEAR) GEAR (LB) GEAR (LC) GEAR (LA) LEVER (HEAD UP) 169 170 171 * 172 * 173 4-988-560-01 4-955-841-11 4-979-914-01 4-983-511-02 4-983-437-01 SCREW (+P 1.7X6) SCREW SPRING (CLV), TORSION PIN (OUTSER T) SLIDER (CAM) 4-979-906-11 SPRING (LEAD SCREW) 4-984-556-01 SHAFT (MAIN SHAFT) 1-667-719-11 SW BOARD Remark Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. HR901 M901 M902 M903 – 99 – 1-500-396-11 HEAD, OVER LIGHT (RF325-74A) A-4672-135-A MOTOR ASSY , SPINDLE A-4672-133-A MOTOR ASSY , SLED A-4672-134-A MOTOR ASSY , LOADING (MD) Remark 8-5. CD MECHANISM DECK SECTION-1 (CDM13C-5BD19) #1 not supplied 211 #1 212 #9 207 208 205 #1 #1 209 206 210 #10 #11 214 213 219 204 218 215 203 202 BU-5BD19 215 #9 M904 216 216 201 not supplied 217 Ref. No. Part No. Description * 201 202 203 204 205 1-634-461-11 4-927-654-01 3-659-338-00 4-929-764-01 4-927-620-01 LOADING BOARD WASHER (LIMITER) SPRING, COMPRESSION SHAFT (TABLE GUIDE) GEAR (P) 206 207 208 209 210 4-944-006-11 4-927-628-01 4-927-649-01 4-929-724-01 X-4947-265-1 BEARING GEAR (C) BELT PULLEY (B) ARM ASSY, SWING Remark Ref. No. Part No. Description 211 212 * 213 * 214 215 4-944-012-01 A-4604-752-A 4-917-583-21 X-4946-208-1 4-933-134-01 TABLE, DISC HOLDER (MG) ASSY BRACKET, YOKE CHASSIS (MD) ASSY SCREW (+PTPWH M2.6X6) 4-958-593-01 4-929-747-01 4-929-727-01 4-929-729-01 A-4608-362-A SPRING (BU), COMPRESSION HOLDER (BU) CAM (A) CAM (B) MOTOR (L) ASSY (LOADING) (CD) 216 217 218 219 M904 – 100 – Remark 8-6. CD MECHANISM DECK SECTION-2 (BU-5BD19) 255 256 rC 257 #12 253 254 M102 254 M101 (including rC) 258 252 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. 251 Ref. No. Part No. Description Remark 251 * 252 253 254 ! 255 4-951-620-01 A-4673-402-A 4-917-565-01 4-951-940-01 8-848-379-31 SCREW (2.6X8), +BVTP BD (CD) BOARD, COMPLETE SHAFT, SLED INSULATOR (BU) OPTICAL PICK-UP KSS-213B/K-N (for CD) Ref. No. 256 257 258 M101 M102 – 101 – Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. Part No. Description 1-769-069-11 4-917-567-01 4-917-564-01 X-4917-523-4 X-4917-504-1 WIRE (FLAT TYPE) (16 CORE) GEAR (M) GEAR (P), FLATNESS BASE (OUTSART) ASSY (SPINDLE) MOTOR ASSY (SLED) Remark SECTION 9 ELECTRICAL PARTS LIST AUDIO Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. When indicating parts by reference number, please include the board name. • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX, -X mean standardized parts, so they may have some difference from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • RESISTORS All resistors are in ohms METAL: Metal-film resistor METAL OXIDE: Metal Oxide-film resistor F : nonflammable Ref. No. Part No. * A-4414-818-A AUDIO BOARD, COMPLETE (AEP,UK,EE) ********************* Description Remark * A-4414-821-A AUDIO BOARD, COMPLETE ********************* (MY,SP,JE,HK,AR,AUS) A-4414-824-A AUDIO BOARD, COMPLETE (US,CND) ********************* * < CAPACITOR > C701 C702 C703 C704 C705 1-126-163-11 1-126-163-11 1-126-163-11 1-126-163-11 1-126-163-11 ELECT ELECT ELECT ELECT ELECT 4.7uF 4.7uF 4.7uF 4.7uF 4.7uF 20% 20% 20% 20% 20% 50V 50V 50V 50V 50V C706 C707 C708 C709 C712 1-136-165-00 1-124-464-11 1-130-473-00 1-126-160-11 1-162-294-31 FILM ELECT MYLAR ELECT CERAMIC 0.1uF 0.22uF 0.0015uF 1uF 0.001uF 5% 20% 5% 20% 10% 50V 50V 50V 50V 50V C713 C714 C715 C716 C717 1-124-589-11 1-136-165-00 1-136-165-00 1-124-261-00 1-126-163-11 ELECT FILM FILM ELECT ELECT 47uF 0.1uF 0.1uF 10uF 4.7uF 20% 5% 5% 20% 20% 16V 50V 50V 50V 50V C718 C719 C720 C731 C743 1-162-290-31 1-124-589-11 1-124-589-11 1-130-475-00 1-124-589-11 CERAMIC ELECT ELECT MYLAR ELECT 470PF 47uF 47uF 0.0022uF 47uF 10% 20% 20% 5% 20% 50V 16V 16V 50V 16V C751 C752 C753 C754 C755 1-126-163-11 1-126-163-11 1-126-163-11 1-126-163-11 1-126-163-11 ELECT ELECT ELECT ELECT ELECT 4.7uF 4.7uF 4.7uF 4.7uF 4.7uF 20% 20% 20% 20% 20% 50V 50V 50V 50V 50V C756 C757 C758 C759 C762 1-136-165-00 1-124-464-11 1-130-473-00 1-126-160-11 1-124-261-00 FILM ELECT MYLAR ELECT ELECT 0.1uF 0.22uF 0.0015uF 1uF 10uF 5% 20% 5% 20% 20% 50V 50V 50V 50V 50V C763 C764 C765 C766 C767 1-130-477-00 1-136-165-00 1-136-165-00 1-124-261-00 1-126-163-11 MYLAR FILM FILM ELECT ELECT 0.0033uF 0.1uF 0.1uF 10uF 4.7uF 5% 5% 5% 20% 20% 50V 50V 50V 50V 50V Ref. No. • SEMICONDUCTORS In each case, u: µ , for example: uA...: µ A..., uPA...: µ PA..., uPB...: µ PB..., uPC...: µ PC..., uPD...: µ PD... • CAPACITORS uF : µ F • COILS uH : µ H • Abbreviation CND : Canadian model EE : East European model MY : Malaysia model SP : Singapore model JE : Tourist model HK : Hong Kong model AR : Argentine model AUS : Australian model Part No. Description C768 C769 C781 C1501 1-162-290-31 1-162-294-31 1-130-475-00 1-124-589-11 CERAMIC CERAMIC MYLAR ELECT Remark C1502 1-164-159-11 CERAMIC 0.1uF C1503 1-126-157-11 ELECT C1504 470PF 0.001uF 0.0022uF 47uF 10% 10% 5% 20% 50V 50V 50V 16V (AEP,UK,EE) 50V (AEP,UK,EE) 10uF 20% 1-162-291-31 CERAMIC 560PF 10% C1505 1-126-157-11 ELECT 10uF 20% C1506 1-124-257-00 ELECT 2.2uF 20% C1507 1-102-518-11 CERAMIC 33PF 5% 16V (AEP,UK,EE) 50V (AEP,UK,EE) 16V (AEP,UK,EE) 50V (AEP,UK,EE) 50V (AEP,UK,EE) C1508 1-162-288-31 CERAMIC 330PF 10% C1509 1-102-518-11 CERAMIC 33PF 5% C1510 1-162-306-11 CERAMIC 0.01uF 20% C1511 1-162-291-31 CERAMIC 560PF 10% C1512 1-162-306-11 CERAMIC 0.01uF 20% C1513 1-162-301-11 CERAMIC 0.0015uF 20% C1515 1-162-600-11 CERAMIC 50V (AEP,UK,EE) 50V (AEP,UK,EE) 16V (AEP,UK,EE) 50V (AEP,UK,EE) 16V (AEP,UK,EE) 16V (AEP,UK,EE) 0.0047uF 20% 16V (AEP,UK,EE) < CONNECTOR > CN701 CN702 1-779-819-11 CONNECTOR, BOARD TO BOARD 14P 1-779-819-11 CONNECTOR, BOARD TO BOARD 14P < DIODE > D701 D1501 8-719-911-19 DIODE 1SS119-25 8-719-911-19 DIODE 1SS119-25 (AEP,UK,EE) < IC > IC701 IC702 IC1500 IC1501 – 102 – 8-759-439-30 8-759-634-51 8-759-450-87 8-759-636-55 IC IC IC IC M62428FP M5218AP BU1922F (AEP,UK,EE) M5218AFP (AEP,UK,EE) AUDIO Ref. No. Part No. Description Remark Ref. No. Part No. < TRANSISTOR > Q701 Q702 Q703 Q751 Q752 8-729-620-05 8-729-141-30 8-729-422-57 8-729-620-05 8-729-141-30 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR BD (CD) Description Remark < VIBRATOR > 2SC2603-EF 2SC3623A-LK UN4111 2SC2603-EF 2SC3623A-LK X1501 1-579-900-21 VIBRATOR, CRYSTAL (4.332MHz)(AEP,UK,EE) ************************************************************** A-4673-402-A BD (CD) BOARD, COMPLETE *********************** < RESISTOR > < CAPACITOR > R702 R703 R704 R705 R706 1-249-433-11 1-247-903-00 1-249-429-11 1-247-843-11 1-247-885-00 CARBON CARBON CARBON CARBON CARBON 22K 1M 10K 3.3K 180K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R707 R708 R709 R710 R712 1-249-425-11 1-249-421-11 1-247-895-00 1-249-435-11 1-249-421-11 CARBON CARBON CARBON CARBON CARBON 4.7K 2.2K 470K 33K 2.2K 5% 5% 5% 5% 5% 1/4W F 1/4W F 1/4W 1/4W 1/4W F R713 R714 R715 R716 R721 1-249-441-11 1-249-413-11 1-249-413-11 1-249-413-11 1-249-420-11 CARBON CARBON CARBON CARBON CARBON 100K 470 470 470 1.8K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R722 R731 R732 R752 R753 1-249-427-11 1-249-420-11 1-249-427-11 1-249-433-11 1-247-903-00 CARBON CARBON CARBON CARBON CARBON 6.8K 1.8K 6.8K 22K 1M 5% 5% 5% 5% 5% 1/4W F 1/4W F 1/4W F 1/4W 1/4W R754 R755 R756 R757 R758 1-249-429-11 1-247-843-11 1-247-885-00 1-249-425-11 1-249-421-11 CARBON CARBON CARBON CARBON CARBON 10K 3.3K 180K 4.7K 2.2K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W F 1/4W F R759 R760 R771 R772 R781 1-247-895-00 1-247-887-00 1-249-420-11 1-249-427-11 1-249-420-11 CARBON CARBON CARBON CARBON CARBON 470K 220K 1.8K 6.8K 1.8K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W F 1/4W F 1/4W F R782 R1501 1-249-427-11 CARBON 1-247-807-31 CARBON 6.8K 100 5% 5% R1502 1-249-432-11 CARBON 18K R1503 1-249-426-11 CARBON 5.6K R1504 1-249-441-11 CARBON 100K R1505 1-249-441-11 CARBON 100K 5% R1506 1-260-079-11 CARBON 22 5% R1507 1-249-417-11 CARBON 1K 5% R1508 1-249-429-11 CARBON 10K 5% R1509 1-249-429-11 CARBON 10K 5% R1510 1-247-903-00 CARBON 1M F F F F 1/4W F 1/4W (AEP,UK,EE) 5% 1/4W (AEP,UK,EE) 5% 1/4W (AEP,UK,EE) 5% 1/4W (AEP,UK,EE) 5% 1/4W (AEP,UK,EE) 1/2W (AEP,UK,EE) 1/4W F (AEP,UK,EE) 1/4W (AEP,UK,EE) 1/4W (AEP,UK,EE) C101 C102 C103 C105 C106 1-126-607-11 1-163-275-11 1-164-346-11 1-163-038-91 1-164-695-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47uF 20% 0.001uF 5% 1uF 0.1uF 0.0022uF 5% 4V 50V 16V 25V 50V C107 C108 C109 C110 C111 1-164-695-11 1-163-021-91 1-163-021-91 1-163-989-11 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.0022uF 0.01uF 0.01uF 0.033uF 0.1uF 5% 10% 10% 10% 50V 50V 50V 25V 25V C112 C113 C114 C115 C116 1-163-038-91 1-164-695-11 1-164-005-11 1-126-607-11 1-163-016-00 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 0.1uF 0.0022uF 5% 0.47uF 47uF 20% 0.0039uF 10% 25V 50V 25V 4V 50V C117 C118 C119 C120 C121 1-164-005-11 1-107-823-11 1-163-038-91 1-135-201-11 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP 0.47uF 0.47uF 0.1uF 10uF 0.1uF 25V 16V 25V 4V 25V C122 C123 C124 C125 C126 1-163-021-91 1-163-038-91 1-126-607-11 1-163-021-91 1-163-038-91 CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.1uF 47uF 0.01uF 0.1uF C127 C128 C129 C130 C131 1-164-695-11 1-163-135-00 1-163-038-91 1-164-336-11 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.0022uF 5% 560PF 5% 0.1uF 0.33uF 0.1uF 50V 50V 25V 25V 25V C132 C133 C134 C135 C136 1-163-037-11 1-163-145-00 1-164-346-11 1-163-251-11 1-164-005-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.022uF 10% 0.0015uF 5% 1uF 100PF 5% 0.47uF 25V 50V 16V 50V 25V C137 C139 C140 C141 C142 1-163-021-91 1-163-235-11 1-163-235-11 1-163-038-91 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 22PF 22PF 0.1uF 0.1uF 10% 5% 5% 50V 50V 50V 25V 25V C145 C146 C147 C148 C149 1-135-201-11 1-135-201-11 1-163-275-11 1-163-275-11 1-164-346-11 TANTALUM CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 10uF 0.001uF 0.001uF 1uF 20% 20% 5% 5% 4V 4V 50V 50V 16V C153 C154 1-135-259-11 TANTAL. CHIP 1-163-235-11 CERAMIC CHIP 10uF 22PF 20% 5% 6.3V 50V 1/4W (AEP,UK,EE) – 103 – 10% 20% 10% 20% 10% 50V 25V 4V 50V 25V BD (CD) Ref. No. BD (MD) Part No. Description Remark Ref. No. < CONNECTOR > CNU101 1-770-014-11 CONNECTOR, FFC/FPC 16P CNU102 1-770-013-11 CONNECTOR, FFC/FPC 19P Part No. Description R144 R145 R146 R147 R148 1-216-073-00 1-216-097-91 1-216-097-91 1-216-049-91 1-216-049-91 METAL CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 100K 100K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W Remark R149 R150 R151 R152 R153 1-216-049-91 1-216-037-00 1-216-037-00 1-216-037-00 1-216-082-00 RES,CHIP METAL CHIP METAL CHIP METAL CHIP RES,CHIP 1K 330 330 330 24K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R154 R156 R157 R158 1-216-065-91 1-216-085-00 1-216-069-00 1-216-001-00 RES,CHIP METAL CHIP METAL CHIP METAL CHIP 4.7K 33K 6.8K 10 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W < IC > IC101 IC102 IC103 IC104 8-752-069-56 8-759-291-06 8-752-372-94 8-759-185-29 IC IC IC IC CXA1782BQ BA6397FP-T1 CXD2507AQ PCM1710U-B < TRANSISTOR > Q101 Q102 Q103 8-729-010-08 TRANSISTOR MSB710-R 8-729-424-08 TRANSISTOR UN2111 8-729-421-22 TRANSISTOR UN2211 < VARIABLE RESISTOR > < RESISTOR > RV101 RV102 RV103 1-223-587-11 RES, ADJ, CARBON 22K 1-223-587-11 RES, ADJ, CARBON 22K 1-223-587-11 RES, ADJ, CARBON 22K R102 R103 R104 R105 R106 1-216-001-00 1-216-049-91 1-216-097-91 1-216-093-00 1-216-093-00 METAL CHIP RES,CHIP RES,CHIP METAL CHIP METAL CHIP 10 1K 100K 68K 68K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R107 R108 R109 R112 R113 1-216-093-00 1-216-093-00 1-216-097-91 1-216-083-00 1-216-083-00 METAL CHIP METAL CHIP RES,CHIP METAL CHIP METAL CHIP 68K 68K 100K 27K 27K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R114 R115 R116 R117 R118 1-216-101-00 1-216-101-00 1-216-061-00 1-216-069-00 1-216-049-91 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES,CHIP 150K 150K 3.3K 6.8K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R119 R120 R121 R122 R123 1-216-089-91 1-216-089-91 1-216-114-00 1-216-097-91 1-216-099-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP METAL CHIP 47K 47K 510K 100K 120K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C101 C102 C103 C104 C105 1-104-851-11 1-163-038-91 1-104-851-11 1-104-851-11 1-163-021-91 TANTAL. CHIP CERAMIC CHIP TANTAL. CHIP TANTAL. CHIP CERAMIC CHIP 10uF 0.1uF 10uF 10uF 0.01uF R124 R125 R126 R127 R128 1-216-091-00 1-216-069-00 1-216-063-91 1-216-089-91 1-216-105-91 METAL CHIP METAL CHIP RES,CHIP RES,CHIP RES,CHIP 56K 6.8K 3.9K 47K 220K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C106 C107 C108 C109 C110 1-163-275-11 1-163-038-91 1-163-038-91 1-163-037-11 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.001uF 0.1uF 0.1uF 0.022uF 0.1uF 5% R129 R130 R131 R132 R133 1-216-049-91 1-216-079-00 1-216-079-00 1-216-061-00 1-216-061-00 RES,CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1K 18K 18K 3.3K 3.3K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C111 C112 C113 C115 C116 1-164-344-11 1-163-017-00 1-164-346-11 1-164-489-11 1-163-037-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.068uF 0.0047uF 1uF 0.22uF 0.022uF 10% 5% R134 R135 R136 R137 R138 1-216-065-91 1-216-065-91 1-216-073-00 1-216-065-91 1-216-049-91 RES,CHIP RES,CHIP METAL CHIP RES,CHIP RES,CHIP 4.7K 4.7K 10K 4.7K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C117 C118 C119 C121 C122 1-163-038-91 1-163-038-91 1-104-851-11 1-126-206-11 1-163-021-91 CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP ELECT CHIP CERAMIC CHIP 0.1uF 0.1uF 10uF 100uF 0.01uF R139 R140 R141 R142 R143 1-216-033-00 1-216-081-00 1-216-061-00 1-216-061-00 1-216-121-91 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES,CHIP 220 22K 3.3K 3.3K 1M 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W C123 C124 C127 C128 C129 1-163-038-91 1-163-038-91 1-163-038-91 1-163-021-91 1-107-823-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.01uF 0.47uF < SWITCH > S101 1-572-085-11 SWITCH, LEAF (LIMIT) < VIBRATOR > X101 1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz) ************************************************************** A-4699-808-A BD (MD) BOARD, COMPLETE *********************** * < CAPACITOR > – 104 – 20% 20% 20% 10% 10% 10V 25V 10V 10V 50V 50V 25V 25V 25V 25V 10% 10% 25V 50V 16V 16V 25V 20% 20% 10% 25V 25V 10V 6.3V 50V 10% 10% 25V 25V 25V 50V 16V BD (MD) Ref. No. C130 C131 C132 C133 C134 Part No. Description 1-163-251-11 1-163-023-00 1-107-823-11 1-163-017-00 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP Remark 100PF 0.015uF 0.47uF 0.0047uF 0.1uF 5% 5% 10% 5% 50V 50V 16V 50V 25V C135 C136 C139 C140 C142 1-163-038-91 1-126-206-11 1-163-235-11 1-163-099-00 1-163-251-11 CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 100uF 22PF 18PF 100PF C143 C144 C151 C152 C153 1-163-251-11 1-163-251-11 1-126-206-11 1-163-038-91 1-163-021-91 CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 100PF 100PF 100uF 0.1uF 0.01uF C156 C158 C160 C161 C163 1-163-038-91 1-163-019-00 1-104-601-11 1-104-601-11 1-163-021-91 CERAMIC CHIP CERAMIC CHIP ELECT CHIP ELECT CHIP CERAMIC CHIP 0.1uF 0.0068uF 10uF 10uF 0.01uF C164 C167 C168 C169 C171 1-163-021-91 1-163-038-91 1-163-038-91 1-104-851-11 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTAL. CHIP CERAMIC CHIP 0.01uF 0.1uF 0.1uF 10uF 0.1uF 10% C181 C182 C183 C184 C185 1-126-206-11 1-163-038-91 1-163-038-91 1-117-970-11 1-164-611-11 ELECT CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 100uF 0.1uF 0.1uF 22uF 0.001uF 20% C188 C189 C190 C191 C192 1-163-021-91 1-163-989-11 1-126-206-11 1-163-038-91 1-163-038-91 CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP 0.01uF 0.033uF 100uF 0.1uF 0.1uF 10% 10% 20% C197 C201 C202 C203 C205 1-163-038-91 1-164-695-11 1-164-695-11 1-163-038-91 1-126-206-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP 0.1uF 0.0022uF 5% 0.0022uF 5% 0.1uF 100uF 20% 25V 50V 50V 25V 6.3V C206 C207 C208 C209 C210 1-115-363-11 1-163-038-91 1-115-363-11 1-163-038-91 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.1uF 10uF 0.1uF 0.1uF 10V 25V 10V 25V 25V C212 C213 C214 C216 C350 1-163-038-91 1-115-363-11 1-115-363-11 1-124-779-00 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP CERAMIC CHIP 0.1uF 10uF 10uF 10uF 0.1uF 25V 10V 10V 16V 25V C352 C353 C354 C355 C357 1-124-779-00 1-163-038-91 1-163-038-91 1-163-251-11 1-163-021-91 ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 0.1uF 0.1uF 100PF 0.01uF 20% 5% 10% 16V 25V 25V 50V 50V C358 C359 1-163-251-11 CERAMIC CHIP 1-163-251-11 CERAMIC CHIP 100PF 100PF 5% 5% 50V 50V 20% 5% 5% 5% 5% 5% 20% 25V 6.3V 50V 50V 50V 10% 50V 50V 6.3V 25V 50V 10% 20% 20% 10% 25V 50V 10V 10V 50V 20% 20% 10% 20% Part No. Description Remark C361 C362 C363 1-163-038-91 CERAMIC CHIP 1-163-251-11 CERAMIC CHIP 1-163-251-11 CERAMIC CHIP 0.1uF 100PF 100PF C401 C402 C2001 C2002 C2003 1-163-038-91 1-163-021-91 1-163-038-91 1-163-038-91 1-163-038-91 0.1uF 0.01uF 0.1uF 0.1uF 0.1uF C2004 1-163-038-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 5% 5% 10% 0.1uF < CONNECTOR > CN101 CN104 CN106 CN107 1-766-508-11 1-778-283-11 1-774-771-11 1-779-854-11 CONNECTOR, FFC/FPC (ZIF) 22P CONNECTOR, FFC/FPC 4P CONNECTOR, FFC/FPC 14P CONNECTOR, FFC/FPC 25P < DIODE > D101 D181 D183 50V 25V 25V 10V 25V 8-719-988-62 DIODE 1SS355 8-719-046-86 DIODE F1J6TP 8-719-046-86 DIODE F1J6TP < IC > 6.3V 25V 25V 10V 500V 50V 25V 6.3V 25V 25V Ref. No. IC101 IC103 IC121 IC124 IC152 8-752-080-95 8-729-903-10 8-752-384-47 8-759-536-21 8-759-430-25 IC IC IC IC IC CXA2523AR TRANSISTOR FMW1 CXD2652AR MSM51V4400D-10TSK-FS BH6511FS-E2 IC153 IC171 IC181 IC192 IC201 8-759-481-19 8-759-484-73 8-759-481-17 8-759-460-72 8-759-471-38 IC IC IC IC IC LB1830M-S-TE-L BR24C01AF-E2 MC74ACT08DTR2 BA033FP-E2 AK4520A-VF-E2 IC316 IC401 8-759-568-55 IC M30610MCA-272FP 8-759-242-70 IC TC7WU04F < COIL > L101 L102 L103 L105 L106 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 1-414-235-11 INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP 0uH 0uH 0uH 0uH 0uH L121 L122 L151 L152 L153 1-414-235-11 1-414-235-11 1-412-622-51 1-412-622-51 1-412-039-51 INDUCTOR CHIP INDUCTOR CHIP INDUCTOR INDUCTOR INDUCTOR CHIP 0uH 0uH 10uH 10uH 100uH L154 L161 L162 L181 L201 1-412-039-51 1-414-235-11 1-414-235-11 1-424-675-11 1-412-776-11 INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR INDUCTOR 100uH 0uH 0uH 0uH 1uH L301 L351 L401 L1001 1-414-235-11 1-216-295-91 1-216-025-91 1-500-445-21 INDUCTOR CHIP 0uH SHORT 0 RES,CHIP 100 5% 1/10W FERRITE 0uH – 105 – 25V 50V 50V 25V 50V 25V 25V 25V 25V BD (MD) Ref. No. Part No. Description Remark < TRANSISTOR > Q101 Q102 Q103 Q104 Q162 8-729-028-91 8-729-026-53 8-729-028-99 8-729-028-99 8-729-101-07 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR RT1P441M-TP-1 2SA1576A-T106-QR RT1N144M-TP-1 RT1N144M-TP-1 2SB798-DL Q163 Q181 Q182 Q350 8-729-028-91 8-729-018-75 8-729-017-65 8-729-028-99 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR RT1P441M-TP-1 2SJ278MY 2SK1764KY RT1N144M-TP-1 < RESISTOR > Ref. No. Part No. Description R182 R183 R184 R188 R189 1-216-089-91 1-216-089-91 1-216-073-00 1-216-073-00 1-216-073-00 RES,CHIP RES,CHIP METAL CHIP METAL CHIP METAL CHIP 47K 47K 10K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R190 R195 R196 R197 R198 1-216-073-00 1-216-295-91 1-216-295-91 1-216-295-91 1-216-295-91 METAL CHIP SHORT SHORT SHORT SHORT 10K 0 0 0 0 5% 1/10W R199 R200 R202 R203 R204 1-216-295-91 1-216-295-91 1-216-041-00 1-216-025-91 1-216-025-91 SHORT SHORT METAL CHIP RES,CHIP RES,CHIP 0 0 470 100 100 5% 5% 5% 1/10W 1/10W 1/10W R210 R330 R331 R332 R333 1-216-041-00 1-216-073-00 1-216-073-00 1-216-097-91 1-216-073-00 METAL CHIP METAL CHIP METAL CHIP RES,CHIP METAL CHIP 470 10K 10K 100K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R351 R352 R356 R361 R362 1-216-053-00 1-216-061-00 1-216-025-91 1-216-073-00 1-216-025-91 METAL CHIP METAL CHIP RES,CHIP METAL CHIP RES,CHIP 1.5K 3.3K 100 10K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R363 R366 R367 R379 R380 1-216-073-00 1-216-097-91 1-216-097-91 1-216-073-00 1-216-073-00 METAL CHIP RES,CHIP RES,CHIP METAL CHIP METAL CHIP 10K 100K 100K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R381 R382 R383 R384 R386 1-216-073-00 1-216-073-00 1-216-073-00 1-216-073-00 1-216-073-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 10K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R387 R388 R389 R391 R393 1-216-069-00 1-216-069-00 1-216-069-00 1-216-073-00 1-216-073-00 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 6.8K 6.8K 6.8K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R400 R401 R402 R405 R420 1-216-073-00 1-216-089-91 1-216-113-00 1-216-063-91 1-216-097-91 METAL CHIP RES,CHIP METAL CHIP RES,CHIP RES,CHIP 10K 47K 470K 3.9K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R421 R422 R423 R424 R425 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1-216-097-91 RES,CHIP 1-216-097-91 RES,CHIP 100K 100K 5% 5% 1/10W 1/10W R101 R103 R104 R105 R106 1-216-025-91 1-216-049-91 1-216-073-00 1-216-065-91 1-216-133-00 RES,CHIP RES,CHIP METAL CHIP RES,CHIP METAL CHIP 100 1K 10K 4.7K 3.3M 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R107 R110 R112 R113 R115 1-216-113-00 1-216-073-00 1-216-089-91 1-216-049-91 1-216-049-91 METAL CHIP METAL CHIP RES,CHIP RES,CHIP RES,CHIP 470K 10K 47K 1K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R117 R121 R125 R128 R131 1-216-113-00 1-216-097-91 1-216-025-91 1-216-041-00 1-216-073-00 METAL CHIP RES,CHIP RES,CHIP METAL CHIP METAL CHIP 470K 100K 100 470 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R132 R133 R134 R135 R136 1-216-097-91 1-216-117-00 1-216-049-91 1-216-061-00 1-216-049-91 RES,CHIP METAL CHIP RES,CHIP METAL CHIP RES,CHIP 100K 680K 1K 3.3K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R137 R140 R142 R143 R144 1-216-025-91 1-216-029-00 1-216-073-00 1-216-073-00 1-216-025-91 RES,CHIP METAL CHIP METAL CHIP METAL CHIP RES,CHIP 100 150 10K 10K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R146 R147 R148 R158 R159 1-216-037-00 1-216-025-91 1-216-045-00 1-216-097-91 1-216-097-91 METAL CHIP RES,CHIP METAL CHIP RES,CHIP RES,CHIP 330 100 680 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R161 R162 R163 R164 R165 1-216-057-00 1-216-057-00 1-216-057-00 1-216-033-00 1-216-097-91 METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES,CHIP 2.2K 2.2K 2.2K 220 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R166 R167 R169 R170 R171 1-220-149-11 1-216-065-91 1-219-724-11 1-216-073-00 1-216-073-00 REGISTER RES,CHIP METAL CHIP METAL CHIP METAL CHIP 2.2 4.7K 1 10K 10K 10% 5% 1% 5% 5% 1/2W 1/10W 1/4W 1/10W 1/10W R175 R177 R178 R179 R180 1-216-061-00 1-216-061-00 1-216-295-91 1-216-091-00 1-216-073-00 METAL CHIP METAL CHIP SHORT METAL CHIP METAL CHIP 3.3K 3.3K 0 56K 10K 5% 5% 1/10W 1/10W R429 R430 R431 R432 R433 5% 5% 1/10W 1/10W R434 R435 – 106 – Remark HP BD (MD) Ref. No. Part No. Description JACK Remark Ref. No. Part No. R438 R439 R440 1-216-097-91 RES,CHIP 1-216-097-91 RES,CHIP 1-216-097-91 RES,CHIP 100K 100K 100K 5% 5% 5% 1/10W 1/10W 1/10W * A-4414-823-A JACK BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS) ******************** Description Remark * R441 R442 R443 R444 R445 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W A-4414-826-A JACK BOARD, COMPLETE (US,CND) ******************** * A-4414-830-A JACK BOARD, COMPLETE (AEP,UK,EE) ******************** R448 R449 R451 R454 R455 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 1-216-097-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R456 R457 R458 R460 R462 1-216-097-91 1-216-097-91 1-216-097-91 1-216-073-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP METAL CHIP METAL CHIP 100K 100K 100K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R502 R504 R600 R602 R603 1-216-295-91 1-216-295-91 1-216-053-00 1-216-025-91 1-216-025-91 SHORT SHORT METAL CHIP RES,CHIP RES,CHIP 0 0 1.5K 100 100 5% 5% 5% 1/10W 1/10W 1/10W R604 R605 R606 R607 R608 1-216-061-00 1-216-025-91 1-216-061-00 1-216-061-00 1-216-025-91 METAL CHIP RES,CHIP METAL CHIP METAL CHIP RES,CHIP 3.3K 100 3.3K 3.3K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R2001 R2002 1-216-001-00 METAL CHIP 1-216-296-91 SHORT 10 0 5% 1/10W < CAPACITOR > C401 C411 C412 C413 C421 1-162-282-21 1-162-282-31 1-162-290-31 1-126-964-11 1-162-282-31 CERAMIC CERAMIC CERAMIC ELECT CERAMIC 100PF 100PF 470PF 10uF 100PF 10% 10% 10% 20% 10% C422 C431 C432 C448 1-162-282-31 1-126-934-11 1-126-933-11 1-136-165-00 CERAMIC ELECT ELECT FILM 100PF 220uF 100uF 0.1uF 10% 20% 20% 5% C449 1-136-165-00 FILM 0.1uF C498 1-136-165-00 FILM 0.1uF 5% C499 1-136-165-00 FILM 0.1uF 5% C451 C461 C462 1-162-282-31 CERAMIC 1-162-282-31 CERAMIC 1-162-290-31 CERAMIC 100PF 100PF 470PF 10% 10% 10% C463 C473 1-126-964-11 ELECT 1-136-173-00 FILM 10uF 0.47uF 20% 5% 50V 50V 50V 50V 50V 50V 10V 16V 50V (AEP,UK,EE) 5% 50V (AEP,UK,EE) 50V (AEP,UK,EE) 50V (AEP,UK,EE) 50V 50V 50V < CONNECTOR > < VIBRATOR > X101 X302 1-767-286-11 VIBRATOR, CRYSTAL (22.5792MHz) 1-767-670-11 VIBRATOR, CERAMIC (7MHz) ************************************************************** 1-671-020-21 HP BOARD ******** * * CN401 CN402 CN404 * CN420 * CN430 1-568-858-11 1-564-506-11 1-770-379-11 1-565-561-11 1-565-500-11 SOCKET, CONNECTOR 15P PLUG, CONNECTOR 3P CONNECTOR, BOARD TO BOARD 6P PIN, CONNECTOR 3P CONNECTOR, BOARD TO BOARD 9P * CN490 1-568-943-11 PIN, CONNECTOR 5P < DIODE > < CAPACITOR > C1401 C1402 1-162-294-31 CERAMIC 1-162-294-31 CERAMIC 0.001uF 0.001uF 10% 10% D422 D430 D447 D497 50V 50V 8-719-911-19 8-719-911-19 8-719-911-19 8-719-911-19 DIODE DIODE DIODE DIODE 1SS119-25 1SS119-25 1SS119-25 1SS119-25 < JACK > < JACK > J1400 1-764-106-21 JACK (PHONES) ************************************************************** J401 J402 1-764-767-21 JACK, PIN 2P (TAPE INPUT) 1-764-767-21 JACK, PIN 2P (TAPE OUTPUT) < COIL > L448 L498 1-420-872-00 COIL, AIR-CORE 1-420-872-00 COIL, AIR-CORE < TRANSISTOR > Q400 Q410 Q420 – 107 – 8-729-620-05 TRANSISTOR 2SC2603-EF 8-729-141-30 TRANSISTOR 2SC3623A-LK 8-729-620-05 TRANSISTOR 2SC2603-EF 50V 50V JACK Ref. No. LOADING Part No. MAIN Description Remark Q431 Q432 8-729-900-80 TRANSISTOR DTC114ES 8-729-620-05 TRANSISTOR 2SC2603-EF Q433 Q434 Q435 Q436 Q450 8-729-620-05 8-729-119-76 8-729-620-05 8-729-620-05 8-729-620-05 Q460 8-729-141-30 TRANSISTOR 2SC3623A-LK Ref. No. Part No. Remark < RELAY > RY430 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR Description 2SC2603-EF 2SA1175-HFE 2SC2603-EF 2SC2603-EF 2SC2603-EF 1-515-833-11 RELAY < TERMINAL > TM440 1-537-238-31 TERMINAL BOARD (SPEAKER) ************************************************************** 1-634-461-11 LOADING BOARD ************* * < RESISTOR > R401 R402 R403 R404 R405 1-249-417-11 1-249-441-11 1-249-425-11 1-249-425-11 1-249-429-11 CARBON CARBON CARBON CARBON CARBON 1K 100K 4.7K 4.7K 10K 5% 5% 5% 5% 5% 1/4W F 1/4W 1/4W F 1/4W F 1/4W R411 R412 R413 R414 R415 1-249-441-11 1-249-417-11 1-249-429-11 1-249-421-11 1-249-441-11 CARBON CARBON CARBON CARBON CARBON 100K 1K 10K 2.2K 100K 5% 5% 5% 5% 5% 1/4W 1/4W F 1/4W 1/4W F 1/4W R421 R422 R423 R424 R431 1-249-393-11 1-249-429-11 1-249-425-11 1-249-831-11 1-249-437-11 CARBON CARBON CARBON CARBON CARBON 10 10K 4.7K 1K 47K 5% 5% 5% 5% 5% 1/4W F 1/4W 1/4W F 1/4W 1/4W R433 R434 R435 R436 R437 1-249-433-11 1-249-431-11 1-249-437-11 1-249-433-11 1-249-417-11 CARBON CARBON CARBON CARBON CARBON 22K 15K 47K 22K 1K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W F ! R444 1-215-914-11 METAL OXIDE 330 5% 3W F (US,CND,MY,SP,JE,HK,AR,AUS) METAL OXIDE 390 5% 3W F (AEP,UK,EE) CARBON 150 5% 1/2W CARBON 150 5% 1/2W CARBON 15K 5% 1/4W ! R444 1-216-478-11 R445 R446 R447 1-260-089-11 1-260-089-11 1-249-431-11 R448 R449 1-260-076-11 CARBON 1-260-076-11 CARBON 10 10 R451 R452 R453 1-249-417-11 CARBON 1-249-441-11 CARBON 1-249-425-11 CARBON 1K 100K 4.7K 1/2W 1/2W (AEP,UK,EE) 5% 1/4W F 5% 1/4W 5% 1/4W F R454 R455 R461 R462 R463 1-249-425-11 1-249-429-11 1-249-441-11 1-249-417-11 1-249-429-11 CARBON CARBON CARBON CARBON CARBON 4.7K 10K 100K 1K 10K 5% 5% 5% 5% 5% 1/4W F 1/4W 1/4W 1/4W F 1/4W R464 R465 R495 R496 R497 1-249-421-11 1-249-441-11 1-260-089-11 1-260-089-11 1-249-431-11 CARBON CARBON CARBON CARBON CARBON 2.2K 100K 150 150 15K 5% 5% 5% 5% 5% 1/4W F 1/4W 1/2W 1/2W 1/4W R498 R499 1-260-076-11 CARBON 1-260-076-11 CARBON 10 10 5% 5% 1/2W 1/2W (AEP,UK,EE) 5% 5% < CONNECTOR > * CN291 1-564-498-11 PIN, CONNECTOR 5P < SWITCH > S291 S292 1-571-924-11 SWITCH, LEAF (LOAD OUT) 1-571-924-11 SWITCH, LEAF (LOAD IN) ************************************************************** * A-4417-124-A MAIN BOARD, COMPLETE (AEP,UK,EE) ******************** * A-4417-128-A MAIN BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS) ******************** * A-4417-132-A MAIN BOARD, COMPLETE (US,CND) ******************** < CAPACITOR > C501 C502 C503 C504 C511 1-128-548-11 1-104-665-11 1-136-165-00 1-136-165-00 1-126-795-11 ELECT ELECT FILM FILM ELECT 4700uF 100uF 0.1uF 0.1uF 10uF 20% 20% 5% 5% 20% 25V 25V 50V 50V 25V C512 C513 C514 C515 C516 1-126-767-11 1-162-306-11 1-126-926-11 1-126-934-11 1-126-933-11 ELECT CERAMIC ELECT ELECT ELECT 1000uF 0.01uF 1000uF 220uF 100uF 20% 20% 20% 20% 20% 16V 16V 10V 16V 16V C522 C523 C525 C531 C532 1-126-934-11 1-126-934-11 1-126-933-11 1-126-969-11 1-126-969-11 ELECT ELECT ELECT ELECT ELECT 220uF 220uF 100uF 220uF 220uF 20% 20% 20% 20% 20% 16V 16V 16V 50V 50V C533 C535 C536 C550 C551 1-126-969-11 1-126-964-11 1-126-947-11 1-117-850-11 1-136-165-00 ELECT ELECT ELECT ELECT FILM 220uF 10uF 47uF 15000uF 0.1uF 20% 20% 20% 20% 5% 50V 50V 35V 16V 50V C552 C561 C562 C563 C564 1-136-165-00 1-126-791-11 1-126-916-11 1-162-306-11 1-126-964-11 FILM ELECT ELECT CERAMIC ELECT 0.1uF 10uF 1000uF 0.01uF 10uF 5% 20% 20% 20% 20% 50V 16V 6.3V 16V 50V C565 C566 C572 1-126-916-11 ELECT 1-126-916-11 ELECT 1-126-960-11 ELECT 1000uF 1000uF 1uF 20% 20% 20% 6.3V 6.3V 50V – 108 – The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C573 C574 1-126-965-11 ELECT 1-126-934-11 ELECT 22uF 220uF 20% 20% 50V 10V C575 C576 C577 C578 C579 1-126-934-11 1-126-964-11 1-126-934-11 1-164-159-11 1-110-489-11 ELECT ELECT ELECT CERAMIC CAPACITOR 220uF 10uF 220uF 0.1uF 1F 20% 20% 20% 10V 50V 10V 50V 5.5V C580 C591 C592 C602 C604 1-126-933-11 1-126-163-11 1-164-159-11 1-164-159-11 1-126-960-11 ELECT ELECT CERAMIC CERAMIC ELECT 100uF 4.7uF 0.1uF 0.1uF 1uF 20% 20% 20% 16V 50V 50V 50V 50V C608 C612 C613 C614 C615 1-124-261-00 1-124-589-11 1-162-306-11 1-102-514-11 1-102-958-00 ELECT ELECT CERAMIC CERAMIC CERAMIC 10uF 47uF 0.01uF 22PF 20PF 20% 20% 20% 5% 5% 50V 16V 16V 50V 50V C616 C617 C618 C619 C620 1-124-589-11 1-162-294-31 1-136-165-00 1-136-165-00 1-136-165-00 ELECT CERAMIC FILM FILM FILM 47uF 0.001uF 0.1uF 0.1uF 0.1uF 20% 10% 5% 5% 5% 16V 50V 50V 50V 50V C621 C622 C807 C808 C809 1-124-589-11 1-125-623-11 1-164-159-11 1-104-664-11 1-126-925-11 ELECT DOUBLE LAYER CERAMIC ELECT ELECT 47uF 0.22F 0.1uF 47uF 470uF 20% 0 20% 20% 16V 5.5V 50V 16V 10V C814 C815 C816 C817 C821 1-162-306-11 1-162-306-11 1-162-306-11 1-104-664-11 1-124-261-00 CERAMIC CERAMIC CERAMIC ELECT ELECT 0.01uF 0.01uF 0.01uF 47uF 10uF 20% 20% 20% 20% 20% 16V 16V 16V 16V 50V C822 C823 C831 C832 C833 1-162-290-31 1-126-916-11 1-124-261-00 1-162-290-31 1-126-964-11 CERAMIC ELECT ELECT CERAMIC ELECT 470PF 1000uF 10uF 470PF 10uF 10% 20% 20% 10% 20% 50V 6.3V 50V 50V 50V C834 C835 C837 C839 C841 1-162-306-11 1-162-285-31 1-126-925-11 1-162-282-31 1-164-159-11 CERAMIC CERAMIC ELECT CERAMIC CERAMIC 0.01uF 180PF 470uF 100PF 0.1uF 20% 10% 20% 10% 16V 50V 10V 50V 50V EPT501 1-537-770-21 TERMINAL BOARD, GROUND C842 C871 C872 C881 1-164-159-11 1-126-163-11 1-126-163-11 1-126-959-11 CERAMIC ELECT ELECT ELECT 0.1uF 4.7uF 4.7uF 0.47uF 50V 50V 50V 50V FB802 FB803 FB805 FB806 CN872 * CN873 20% 20% 20% 1-779-820-11 CONNECTOR, BOARD TO BOARD 14P 1-568-839-11 SOCKET, CONNECTOR 23P < DIODE > D501 D502 D503 D504 D511 8-719-200-82 8-719-200-82 8-719-200-82 8-719-200-82 8-719-110-09 DIODE DIODE DIODE DIODE DIODE 11ES2 11ES2 11ES2 11ES2 RD8.2ES-B3 D521 D531 D532 D533 D534 8-719-929-15 8-719-200-82 8-719-200-82 8-719-200-82 8-719-983-88 DIODE DIODE DIODE DIODE DIODE MZS9.1NB2 11ES2 11ES2 11ES2 MTZJ-T-72-33C D551 D552 D553 D554 D561 8-719-200-02 8-719-200-02 8-719-200-02 8-719-200-02 8-719-200-82 DIODE DIODE DIODE DIODE DIODE 10E2 10E2 10E2 10E2 11ES2 D562 D563 D571 D572 D581 8-719-911-19 8-719-200-82 8-719-911-19 8-719-911-19 8-719-911-19 DIODE DIODE DIODE DIODE DIODE 1SS119-25 11ES2 1SS119-25 1SS119-25 1SS119-25 D582 D591 D601 D602 D603 8-719-911-19 8-719-921-80 8-719-911-19 8-719-911-19 8-719-200-82 DIODE DIODE DIODE DIODE DIODE 1SS119-25 MTZJ-11B 1SS119-25 1SS119-25 11ES2 D604 D605 D801 D802 D803 8-719-200-82 8-719-911-19 8-719-911-19 8-719-911-19 8-719-921-40 DIODE DIODE DIODE DIODE DIODE 11ES2 1SS119-25 1SS119-25 1SS119-25 MTZJ-4.7C D881 D882 8-719-911-19 DIODE 1SS119-25 8-719-911-19 DIODE 1SS119-25 < GROUND TERMINAL > < FERRITE BEAD > 1-412-473-21 1-412-473-21 1-412-473-21 1-412-473-21 < CONNECTOR > INDUCTOR INDUCTOR INDUCTOR INDUCTOR 0UH 0UH 0UH 0UH < IC > CN503 CN506 CN590 CN801 * CN802 1-564-511-11 1-770-412-11 1-564-506-11 1-770-067-11 1-564-339-00 PLUG, CONNECTOR 8P CONNECTOR, BOARD TO BOARD 6P PLUG, CONNECTOR 3P CONNECTOR, FFC/FPC 19P PIN, CONNECTOR 5P IC510 IC511 IC560 IC570 IC601 8-759-604-32 8-759-604-86 8-759-450-47 8-759-426-96 8-759-545-08 IC IC IC IC IC M5F7810 M5F7807L BA05T LA5620 uPD78078GF-083-3BA CN820 CN850 CN870 CN871 1-770-653-11 1-691-648-11 1-568-834-11 1-779-820-11 CONNECTOR, FFC/FPC 25P SOCKET, CONNECTOR 15P SOCKET, CONNECTOR 15P CONNECTOR, BOARD TO BOARD 14P IC602 IC603 IC801 IC840 8-759-635-63 8-759-481-02 8-759-822-09 8-759-269-09 IC IC IC IC M51943BSL M62016L LB1641 SN74HCT04ANS – 109 – MAIN Ref. No. IC842 Part No. Description Remark 8-759-267-86 IC SN74HC00ANS-E20 Ref. No. Part No. Description Remark R614 R615 1-247-807-31 CARBON 1-249-425-11 CARBON 100 4.7K 5% 5% 1/4W 1/4W F R616 R617 R618 R619 R620 1-247-843-11 1-249-413-11 1-249-425-11 1-247-843-11 1-249-413-11 CARBON CARBON CARBON CARBON CARBON 3.3K 470 4.7K 3.3K 470 5% 5% 5% 5% 5% 1/4W 1/4W F 1/4W F 1/4W 1/4W F R621 R622 R623 R624 R625 1-247-843-11 1-247-807-31 1-247-807-31 1-249-429-11 1-249-429-11 CARBON CARBON CARBON CARBON CARBON 3.3K 100 100 10K 10K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R626 R627 R628 R630 R631 1-247-807-31 1-247-807-31 1-249-429-11 1-249-429-11 1-249-433-11 CARBON CARBON CARBON CARBON CARBON 100 100 10K 10K 22K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R632 R633 R634 R635 R636 1-249-437-11 1-249-437-11 1-249-429-11 1-247-807-31 1-247-807-31 CARBON CARBON CARBON CARBON CARBON 47K 47K 10K 100 100 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R637 R638 R639 R640 R641 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 CARBON CARBON CARBON CARBON CARBON 100 100 100 100 100 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R642 R643 R644 R645 R646 1-247-807-31 1-247-807-31 1-247-807-31 1-249-425-11 1-247-843-11 CARBON CARBON CARBON CARBON CARBON 100 100 100 4.7K 3.3K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W F 1/4W R647 R648 R649 R650 R651 1-249-429-11 1-249-413-11 1-247-891-00 1-249-417-11 1-249-417-11 CARBON CARBON CARBON CARBON CARBON 10K 470 330K 1K 1K 5% 5% 5% 5% 5% 1/4W 1/4W F 1/4W 1/4W F 1/4W F R652 R653 R654 R655 R656 1-249-417-11 1-249-417-11 1-249-417-11 1-249-417-11 1-249-417-11 CARBON CARBON CARBON CARBON CARBON 1K 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R801 R807 R821 R822 R825 1-249-417-11 1-247-807-31 1-249-441-11 1-249-417-11 1-249-429-11 CARBON CARBON CARBON CARBON CARBON 1K 100 100K 1K 10K 5% 5% 5% 5% 5% 1/4W F 1/4W 1/4W 1/4W F 1/4W R826 R831 R832 R851 R852 1-249-429-11 1-249-441-11 1-249-417-11 1-249-421-11 1-249-431-11 CARBON CARBON CARBON CARBON CARBON 10K 100K 1K 2.2K 15K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W F 1/4W F 1/4W R861 R862 R871 R872 R873 1-249-421-11 1-249-431-11 1-249-421-11 1-249-441-11 1-247-887-00 CARBON CARBON CARBON CARBON CARBON 2.2K 15K 2.2K 100K 220K 5% 5% 5% 5% 5% 1/4W F 1/4W 1/4W F 1/4W 1/4W < COIL > L523 L601 L739 1-408-117-00 INDUCTOR 1-410-509-11 INDUCTOR 1-410-470-11 INDUCTOR 10uH 10uH 10uH < TRANSISTOR > Q510 Q520 Q521 Q530 Q561 8-729-111-29 8-729-118-00 8-729-119-76 8-729-018-59 8-729-118-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SD1616A-K 2SB1116-L 2SA1175-HFE 2SB1375-LC (LB-SONY) 2SB1116 Q562 Q571 Q572 Q591 Q592 8-729-422-73 8-729-422-57 8-729-900-80 8-729-119-76 8-729-021-82 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR UN4212 UN4111 DTC114ES 2SA1175-HFE 2SD2396K Q601 Q602 Q871 Q872 8-729-900-80 8-729-620-05 8-729-422-57 8-729-422-57 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC114ES 2SC2603-EF UN4111 UN4111 < RESISTOR > ! R510 R511 ! R520 R521 R522 1-219-786-11 1-249-413-11 1-219-786-11 1-249-421-11 1-249-417-11 FUSIBLE CARBON FUSIBLE CARBON CARBON 22 470 22 2.2K 1K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W F F F F F ! R530 R531 R562 R563 R564 1-219-153-11 1-260-095-11 1-249-421-11 1-249-409-11 1-247-843-11 FUSIBLE CARBON CARBON CARBON CARBON 10 470 2.2K 220 3.3K 5% 5% 5% 5% 5% 1/4W F 1/2W 1/4W F 1/4W F 1/4W R571 R572 R573 R576 R581 1-249-437-11 1-249-437-11 1-249-437-11 1-249-429-11 1-249-425-11 CARBON CARBON CARBON CARBON CARBON 47K 47K 47K 10K 4.7K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W F R582 ! R590 R591 R592 R593 1-249-425-11 1-217-640-11 1-249-425-11 1-249-441-11 1-249-421-11 CARBON FUSIBLE CARBON CARBON CARBON 4.7K 3.3 4.7K 100K 2.2K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R601 R602 R603 R604 R605 1-249-429-11 1-247-807-31 1-249-429-11 1-247-807-31 1-249-417-11 CARBON CARBON CARBON CARBON CARBON 10K 100 10K 100 1K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W F R606 R607 R608 R609 R610 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 CARBON CARBON CARBON CARBON CARBON 100 100 100 100 100 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R611 R612 R613 1-249-429-11 CARBON 1-247-807-31 CARBON 1-247-807-31 CARBON 10K 100 100 5% 5% 5% 1/4W 1/4W 1/4W F F F F – 110 – The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. F F F F F Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. MAIN Ref. No. R874 R875 R876 R881 Part No. Description 1-249-421-11 1-249-441-11 1-247-887-00 1-247-903-00 CARBON CARBON CARBON CARBON Remark 2.2K 100K 220K 1M 5% 5% 5% 5% 1/4W F 1/4W 1/4W 1/4W < VIBRATOR > X601 X602 Ref. No. Part No. MD LED PANEL Description Remark D903 D904 D906 8-719-058-17 DIODE LNG401NPYJA (p (MD)) 8-719-057-09 DIODE LNJ801LPDJA (r REC) 8-719-057-10 DIODE LNJ301MPUJAB (^ (CD)) D907 D908 8-719-058-17 DIODE LNG401NPYJA (p (CD)) 8-719-057-09 DIODE LNJ801LPDJA (CD INDICATOR) 1-760-489-11 VIBRATOR, CERAMIC (5MHz) 1-567-098-41 VIBRATOR, CRYSTAL (32kHz) < FLUORESCENT INDICATOR > FL901 1-517-687-11 INDICATOR TUBE, FLUORESCENT ************************************************************** < IC > 1-670-745-21 MD LED BOARD ************ * IC901 IC902 8-759-297-23 IC M66004M8FP 8-759-459-83 IC NJL55H400A < DIODE > < TRANSISTOR > D905 8-719-057-09 DIODE LNJ801LPDJA (MD INDICATOR) ************************************************************** * A-4417-317-A PANEL BOARD, COMPLETE ********************* * 4-993-866-21 HOLDER (FL) < CAPACITOR > C901 C902 C903 C923 C935 1-162-306-11 1-162-306-11 1-126-160-11 1-164-159-11 1-124-261-00 CERAMIC CERAMIC ELECT CERAMIC ELECT 0.01uF 0.01uF 1uF 0.1uF 10uF 20% 20% 20% C936 C937 C940 C946 C948 1-124-234-00 1-164-159-11 1-162-282-31 1-164-159-11 1-162-286-31 ELECT CERAMIC CERAMIC CERAMIC CERAMIC 22uF 0.1uF 100PF 0.1uF 220PF 20% 10% 16V 50V 50V 50V 50V C949 C950 C951 C952 C953 1-162-286-31 1-162-286-31 1-162-286-31 1-162-286-31 1-162-286-31 CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC 220PF 220PF 220PF 220PF 220PF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C954 C955 C956 C957 C958 1-162-286-31 1-162-286-31 1-162-286-31 1-162-286-31 1-162-286-31 CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC 220PF 220PF 220PF 220PF 220PF 10% 10% 10% 10% 10% 50V 50V 50V 50V 50V C959 C960 C961 C962 C964 1-162-286-31 1-162-286-31 1-162-286-31 1-162-286-31 1-126-160-11 CERAMIC CERAMIC CERAMIC CERAMIC ELECT 220PF 220PF 220PF 220PF 1uF 10% 10% 10% 10% 20% 50V 50V 50V 50V 50V C965 1-124-589-11 ELECT 47uF 20% 16V 20% 10% 16V 16V 50V 50V 50V Q901 Q902 Q904 Q905 Q906 8-729-620-05 8-729-620-05 8-729-422-57 8-729-422-57 8-729-422-57 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC2603-EF 2SC2603-EF UN4111 UN4111 UN4111 Q907 Q908 Q909 Q910 8-729-422-57 8-729-422-57 8-729-422-57 8-729-422-57 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR UN4111 UN4111 UN4111 UN4111 < RESISTOR > R901 R902 R903 R904 R907 1-249-441-11 1-249-441-11 1-249-417-11 1-249-417-11 1-249-441-11 CARBON CARBON CARBON CARBON CARBON 100K 100K 1K 1K 100K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W F 1/4W F 1/4W R908 R909 R910 R911 R912 1-249-435-11 1-249-417-11 1-249-417-11 1-249-417-11 1-249-417-11 CARBON CARBON CARBON CARBON CARBON 33K 1K 1K 1K 1K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R913 R914 R915 R916 R917 1-249-421-11 1-247-807-31 1-249-409-11 1-247-807-31 1-247-807-31 CARBON CARBON CARBON CARBON CARBON 2.2K 100 220 100 100 5% 5% 5% 5% 5% 1/4W F 1/4W 1/4W F 1/4W 1/4W R918 R919 R920 R921 R922 1-249-409-11 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 CARBON CARBON CARBON CARBON CARBON 220 100 100 100 100 5% 5% 5% 5% 5% 1/4W F 1/4W 1/4W 1/4W 1/4W R924 R925 R928 R930 R932 1-249-407-11 1-249-407-11 1-249-411-11 1-247-807-31 1-249-407-11 CARBON CARBON CARBON CARBON CARBON 150 150 330 100 150 5% 5% 5% 5% 5% 1/4W F 1/4W F 1/4W 1/4W 1/4W F R933 R936 R938 R941 R942 1-249-407-11 1-247-807-31 1-249-393-11 1-249-413-11 1-249-415-11 CARBON CARBON CARBON CARBON CARBON 150 100 10 470 680 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W R943 1-249-417-11 CARBON 1K 5% 1/4W F F F F F < CONNECTOR > * CN901 1-568-865-11 SOCKET, CONNECTOR 23P < DIODE > D901 D902 8-719-921-48 DIODE MTZJ-5.6C 8-719-057-10 DIODE LNJ301MPUJAB (^ (MD)) – 111 – F F F F F PANEL Ref. No. POWER AMP Part No. Description R944 R945 R946 R947 1-249-419-11 1-249-421-11 1-249-413-11 1-249-415-11 CARBON CARBON CARBON CARBON 1.5K 2.2K 470 680 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W Remark F F F F R948 R949 R950 R951 R952 1-249-417-11 1-249-419-11 1-249-421-11 1-249-425-11 1-249-430-11 CARBON CARBON CARBON CARBON CARBON 1K 1.5K 2.2K 4.7K 12K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W F F F F Ref. No. Part No. Description C1255 C1256 C1257 C1260 C1261 1-126-967-11 1-126-948-11 1-136-165-00 1-136-163-00 1-136-163-00 ELECT ELECT FILM FILM FILM 47uF 100uF 0.1uF 0.068uF 0.068uF 20% 20% 5% 5% 5% 50V 35V 50V 50V 50V C1301 C1302 C1303 C1304 1-126-042-11 1-126-042-11 1-136-165-00 1-136-165-00 ELECT ELECT FILM FILM 3300uF 3300uF 0.1uF 0.1uF 20% 20% 5% 5% 35V 35V 50V 50V < SWITCH > < CONNECTOR > S901 S902 S903 S904 S905 1-473-392-11 1-762-875-21 1-762-875-21 1-762-875-21 1-762-875-21 ENCODER, ROTARY (VOLUME) SWITCH, KEYBOARD (1/u) SWITCH, KEYBOARD (p (CD)) SWITCH, KEYBOARD (^ (CD)) SWITCH, KEYBOARD (6 (CD)) S906 S907 S908 S909 S910 1-762-875-21 1-762-875-21 1-762-875-21 1-762-875-21 1-762-875-21 SWITCH, KEYBOARD (p (MD)) SWITCH, KEYBOARD (^ (MD)) SWITCH, KEYBOARD (6 (MD)) SWITCH, KEYBOARD (FUNCTION) SWITCH, KEYBOARD (MD/CD ) +/TUNING +) S911 S912 1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND) 1-762-875-21 SWITCH, KEYBOARD (MD/CD = 0/TUNING -) 1-762-875-21 SWITCH, KEYBOARD (r REC) 1-762-875-21 SWITCH, KEYBOARD (CD-MD SYNC) 1-762-875-21 SWITCH, KEYBOARD (REPEAT/STEREO/MONO) S913 S914 S915 S916 Remark * CN1202 1-565-485-11 CONNECTOR, BOARD TO BOARD 9P < DIODE > 1-762-875-21 SWITCH, KEYBOARD (PLAY MODE/TUNING MODE) ************************************************************** * A-4417-126-A POWER AMP BOARD, COMPLETE (AEP,UK,EE) ************************* * A-4417-130-A POWER AMP BOARD, COMPLETE ************************* (MY,SP,JE,HK,AR,AUS) * A-4417-134-A POWER AMP BOARD, COMPLETE (US,CND) ************************* < CAPACITOR > C1201 C1202 C1203 C1204 C1205 1-126-963-11 1-162-288-31 1-162-286-31 1-126-967-11 1-126-967-11 ELECT CERAMIC CERAMIC ELECT ELECT 4.7uF 330PF 220PF 47uF 47uF 20% 10% 10% 20% 20% 50V 50V 50V 50V 50V C1206 C1207 C1208 C1210 C1211 1-126-948-11 1-136-165-00 1-126-965-11 1-136-163-00 1-136-163-00 ELECT FILM ELECT FILM FILM 100uF 0.1uF 22uF 0.068uF 0.068uF 20% 5% 20% 5% 5% 35V 50V 50V 50V 50V C1220 C1251 C1252 C1253 C1254 1-126-924-11 1-126-963-11 1-162-288-31 1-162-286-31 1-126-967-11 ELECT ELECT CERAMIC CERAMIC ELECT 330uF 4.7uF 330PF 220PF 47uF 20% 20% 10% 10% 20% 10V 50V 50V 50V 50V D1201 D1202 D1203 D1213 D1251 8-719-911-19 8-719-911-19 8-719-911-19 8-719-911-19 8-719-911-19 DIODE DIODE DIODE DIODE DIODE 1SS119-25 1SS119-25 1SS119-25 1SS119-25 1SS119-25 D1263 D1300 8-719-911-19 DIODE 1SS119-25 8-719-025-03 DIODE RBA-402-SL < IC > IC1201 8-749-920-13 IC STK4132MK2 < TRANSISTOR > Q1201 Q1202 Q1231 Q1232 Q1251 8-729-620-05 8-729-900-80 8-729-422-73 8-729-620-05 8-729-620-05 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC2603-EF DTC114ES UN4212 2SC2603-EF 2SC2603-EF < RESISTOR > R1201 R1202 R1203 R1204 R1205 1-249-417-11 1-249-437-11 1-249-417-11 1-249-437-11 1-260-103-11 CARBON CARBON CARBON CARBON CARBON 1K 47K 1K 47K 2.2K 5% 5% 5% 5% 5% 1/4W F 1/4W 1/4W F 1/4W 1/2W R1207 ! R1209 ! R1210 R1211 R1212 1-260-103-11 1-212-881-11 1-217-151-00 1-249-417-11 1-249-431-11 CARBON FUSIBLE METAL CARBON CARBON 2.2K 100 0.22 1K 15K 5% 5% 10% 5% 5% 1/2W 1/4W F 2W 1/4W F 1/4W R1214 R1217 R1218 R1219 R1225 1-260-099-11 1-260-099-11 1-249-397-11 1-249-397-11 1-249-397-11 CARBON CARBON CARBON CARBON CARBON 1K 1K 22 22 22 5% 5% 5% 5% 5% 1/2W 1/2W 1/4W F 1/4W F 1/4W F R1226 R1227 1-249-429-11 CARBON 1-247-854-11 CARBON R1227 1-249-429-11 CARBON R1228 1-247-880-11 CARBON R1228 1-249-441-11 CARBON – 112 – The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. 10K 5% 1/4W 9.1K 5% 1/4W (AEP,UK,EE,MY,SP,JE,HK,AR,AUS) 10K 5% 1/4W (US,CND) 110K 5% 1/4W (AEP,UK,EE) 100K 5% 1/4W (US,CND,MY,SP,JE,HK,AR,AUS) Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. POWER AMP ST TERMINAL SW Ref. No. Part No. Description Remark Ref. No. R1229 R1231 R1232 R1233 ! R1243 1-249-429-11 1-247-807-31 1-249-429-11 1-249-429-11 1-217-637-00 CARBON CARBON CARBON CARBON FUSIBLE 10K 100 10K 10K 1 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W F * CN1601 1-564-518-11 PLUG, CONNECTOR 3P CN1602 1-564-523-11 PLUG, CONNECTOR 8P R1251 R1252 R1253 R1254 R1255 1-249-417-11 1-249-437-11 1-249-417-11 1-249-437-11 1-260-103-11 CARBON CARBON CARBON CARBON CARBON 1K 47K 1K 47K 2.2K 5% 5% 5% 5% 5% 1/4W F 1/4W 1/4W F 1/4W 1/2W R1257 ! R1259 ! R1260 R1261 R1262 1-260-103-11 1-212-881-11 1-217-151-00 1-249-417-11 1-249-431-11 CARBON FUSIBLE METAL CARBON CARBON 2.2K 100 0.22 1K 15K 5% 5% 10% 5% 5% 1/2W 1/4W F 2W 1/4W F 1/4W R1268 R1269 R1271 R1272 R1273 1-249-397-11 1-249-397-11 1-249-431-11 1-249-431-11 1-249-413-11 CARBON CARBON CARBON CARBON CARBON 22 22 15K 15K 470 5% 5% 5% 5% 5% 1/4W F 1/4W F 1/4W 1/4W 1/4W F Part No. TRANS Description Remark < FUSE > ! F1601 ! F1603 1-532-388-31 FUSE (T2AL/250V)(MY,SP,JE,HK,AR,AUS) 1-532-504-31 FUSE (T4AL/250V) (AEP,UK,EE,MY,SP,JE,HK,AR,AUS) 1-533-419-11 FUSE, GLASS CYLINDRICAL (DIA.5)(4A/125V) (US,CND) 1-532-504-31 FUSE (T4AL/250V) (AEP,UK,EE,MY,SP,JE,HK,AR,AUS) 1-533-419-11 FUSE, GLASS CYLINDRICAL (DIA.5)(4A/125V) (US,CND) ! F1603 ! F1605 ! F1605 < FUSE HOLDER > FH1601 FH1602 FH1603 FH1604 FH1605 1-533-293-11 1-533-293-11 1-533-293-11 1-533-293-11 1-533-293-11 FUSE HOLDER (MY,SP,JE,HK,AR,AUS) FUSE HOLDER (MY,SP,JE,HK,AR,AUS) FUSE HOLDER FUSE HOLDER FUSE HOLDER FH1606 1-533-293-11 FUSE HOLDER < THERMISTOR(POSITIVE) > < RESISTOR > THP1230 1-807-796-11 THERMISTOR ! R1600 1-202-725-00 SOLID 3.3M ************************************************************** 1-666-905-11 ST TERMINAL BOARD ***************** * ! S1600 1-762-753-11 SWITCH, VOLTAGE SELECTION (MY,SP,JE,HK,AR,AUS) 1-568-834-11 SOCKET, CONNECTOR 15P 1-774-289-11 PIN, CONNECTOR (PC BOARD) 15P < TRANSFORMER > ************************************************************** ! T1600 ! T1600 ! T1600 1-431-498-11 TRANSFORMER, POWER (MY,SP,JE,HK,AR,AUS) 1-431-988-11 TRANSFORMER, POWER (AEP,UK,EE) 1-431-989-11 TRANSFORMER, POWER (US,CND) 1-667-719-11 SW BOARD ******** * < THERMISTOR(POSITIVE) > < CONNECTOR > CN601 CN602 CN603 1/2W (US,CND) < SWITCH > < CONNECTOR > CN744 CN745 10% THP1600 1-801-696-11 THP1601 1-801-696-11 THP1602 1-801-671-11 THP1603 1-801-671-11 1-770-697-11 CONNECTOR, FFC/FPC 14P 1-778-638-21 PIN, CONNECTOR (PC BOARD) 2P 1-778-638-21 PIN, CONNECTOR (PC BOARD) 2P THERMISTOR, POSITIVE THERMISTOR, POSITIVE THERMISTOR, POSITIVE THERMISTOR, POSITIVE ************************************************************** < SWITCH > S681 S682 S683 S685 S686 1-572-467-61 1-692-377-31 1-692-847-21 1-572-467-61 1-762-621-21 S687 S688 1-572-688-11 SWITCH, PUSH (1 KEY)(PB POSITION) 1-762-621-21 SWITCH, PUSH (1 KEY)(REC POSITION) MISCELLANEOUS ************* SWITCH, PUSH (1 KEY)(LIMIT IN) SWITCH, PUSH (1 KEY)(REFLECT) SWITCH, PUSH (1 KEY)(PROTECT) SWITCH, PUSH (1 KEY)(CHUCKING IN) SWITCH, PUSH (1 KEY)(PACK OUT) ************************************************************** * 1-666-904-11 TRANS BOARD *********** 10 52 56 62 62 1-782-793-11 1-782-990-11 1-782-991-11 1-233-544-21 1-233-546-21 WIRE (FLAT TYPE) (23 CORE) WIRE (FLAT TYPE) (19 CORE) WIRE (FLAT TYPE) (15 CORE) ENCAPSULATED COMPONENT (US,CND) ENCAPSULATED COMPONENT (MY,SP,JE,HK,AR,AUS) 62 64 ! 68 ! 69 102 1-693-387-21 1-783-213-11 1-569-008-21 1-770-019-11 1-660-966-11 TUNER (FM/MW/LW)(AEP,UK,EE) WIRE (FLAT TYPE) (15 CORE) ADAPTOR, CONVERSION 2P (MY,SP,JE) ADAPTOR, CONVERSION PLUG 3P (UK,EE,HK) OP RELAY FLEXIBLE BOARD < CONNECTOR > CN1600 1-564-321-00 PIN, CONNECTOR 2P 103 110 – 113 – 1-782-683-11 WIRE (FLAT TYPE) (14 CORE) 1-783-113-11 WIRE (FLAT TYPE) (25 CORE) The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. HCD-MD333 Ref. No. Part No. ! 167 ! 255 256 8-583-028-02 OPTICAL PICK-UP KMS-260A/J1N (for MD) 8-848-379-31 OPTICAL PICK-UP KSS-213B/K-N (for CD) 1-769-069-11 WIRE (FLAT TYPE) (16 CORE) ! CNP1601 1-696-847-11 ! CNP1601 1-769-744-11 ! CNP1601 1-783-532-11 ! CNP1601 1-783-941-11 FAN901 1-698-997-11 Description Remark CORD, POWER (AUS) CORD, POWER (AEP,UK,EE,MY,SP,JE,HK) CORD, POWER (US,CND) CORD, POWER (AR) FAN, D.C. FL901 HR901 M101 M102 M901 1-517-687-11 1-500-396-11 X-4917-523-4 X-4917-504-1 A-4672-135-A INDICATOR TUBE, FLUORESCENT HEAD, OVER LIGHT (RF325-74A) BASE (OUTSART) ASSY (SPINDLE) MOTOR ASSY (SLED) MOTOR ASSY, SPINDLE M902 M903 M904 ! T1600 ! T1600 A-4672-133-A A-4672-134-A A-4608-362-A 1-431-498-11 1-431-988-11 MOTOR ASSY, SLED MOTOR ASSY, LOADING (MD) MOTOR (L) ASSY (LOADING) (CD) TRANSFORMER, POWER (MY,SP,JE,HK,AR,AUS) TRANSFORMER, POWER (AEP,UK,EE) ! T1600 1-431-989-11 TRANSFORMER, POWER (US,CND) ************************************************************** ************* HARDWARE LIST ************* #1 #2 #3 #4 #5 7-685-646-79 7-685-647-79 7-685-650-79 7-685-871-01 7-685-850-04 SCREW +BVTP 3X8 TYPE2 N-S SCREW +BVTP 3X10 TYPE2 N-S SCREW +BVTP 3X16 TYPE2 IT-3 SCREW +BVTT 3X6 (S) SCREW +BVTT 2X3 (S) #6 #7 #8 #9 #10 7-685-851-04 7-627-553-17 7-627-552-27 7-624-105-04 7-685-234-19 SCREW +BVTT 2X4 (S) PRECISION SCREW +P 2X2 TYPE 3 SCREW,PRECISION +P 1.7X2 STOP RING 2.3, TYPE -E SCREW +KTP 2.6X8 TYPE2NON-SLIT #11 #12 #13 7-621-775-10 SCREW +B 2.6X4 7-621-255-15 SCREW +P 2X3 7-627-852-28 +P 1.7X3 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. – 114 – Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié. HCD-MD333 SERVICE MANUAL 1999 . 11 US Model Canadian Model AEP Model UK Model E Model Australian Model Tourist Model SUPPLEMENT-1 File this supplement with the service manual. Subject: PARTS CHANGED 9-922-935-81 Sony Corporation Home Audio Division Company 99K09013-1D Printed in Japan © 1999. 11 Published by Quality Assurance Dept. 1 PARTS CHANGED ! : indicates changed portion Page New Former Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark EXPLODED VIEWS EXPLODED VIEWS 8-2. CHASSIS SECTION 8-2. CHASSIS SECTION * 55 A-4417-130-A POWER AMP BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS) * 55 A-4417-130-A POWER AMP BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS,KR) * 57 A-4414-823-A JACK BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS) * 57 A-4414-823-A JACK BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS,KR) * 59 4-414-849-61 PANEL, BACK (MY,SP,JE,HK,AR,AUS) * 59 4-414-849-61 PANEL, BACK (MY,SP,JE,HK,AR,AUS,KR) $ $ $ 62 1-233-546-21 ENCAPSULATED COMPONENT (MY,SP,JE,HK,AR,AUS) 62 1-233-546-22 ENCAPSULATED COMPONENT (MY,SP,JE,HK,AR,AUS,KR) $ * 65 A-4417-128-A MAIN BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS) * 65 A-4417-128-A MAIN BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS,KR) * 67 A-4414-821-A AUDIO BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS) * 67 A-4414-821-A AUDIO BOARD, COMPLETE (MY,SP,JE,HK,AR,AUS,KR) 97 $ $ $ 0 CNP1601 1-768-079-21 CORD, POWER (KR) $ CNP1601 KR ELECTRICAL PARTS LIST 102 * * 107 ELECTRICAL PARTS LIST A-4414-821-A AUDIO BOARD, COMPLETE ********************** (MY,SP,JE,HK,AR,AUS) * A-4414-823-A JACK BOARD, COMPLETE ********************* (MY,SP,JE,HK,AR,AUS) * $ A-4414-823-A JACK BOARD, COMPLETE ********************* (MY,SP,JE,HK,AR,AUS,KR) $ < RESISTOR > < RESISTOR > 0 R444 1-215-914-11 METAK OXIDE 330 5% 3W F (US,CND,MY,SP,JE,HK,AR,AUS) 0 R444 1-215-914-11 METAK OXIDE 330 5% 3W F (US,CND,MY,SP,JE,HK,AR,AUS,KR) * A-4417-128-A MAIN BOARD, COMPLETE ********************* (MY,SP,JE,HK,AR,AUS) * A-4417-128-A MAIN BOARD, COMPLETE ********************* (MY,SP,JE,HK,AR,AUS,KR) 108 2 A-4414-821-A AUDIO BOARD, COMPLETE ********************** (MY,SP,JE,HK,AR,AUS,KR) $ $ Page New Former Ref. No. Part No. Description Remark Ref. No. ELECTRICAL PARTS LIST Description Remark ELECTRICAL PARTS LIST A-4417-130-A POWER AMP BOARD, COMPLETE * *************************** (MY,SP,JE,HK,AR,AUS) * Part No. A-4417-130-A POWER AMP BOARD, COMPLETE *************************** (MY,SP,JE,HK,AR,AUS.KR) $ 112 < RESISTOR > < RESISTOR > R1227 1-247-854-11 CARBON 9.1K 5% 1/4W (AEP,UK,EE,MY,SP,JE,HK,AR,AUS) R1227 1-247-854-11 CARBON 9.1K 5% 1/4W (AEP,UK,EE,MY,SP,JE,HK,AR,AUS,KR) R1228 1-249-441-11 CARBON R1228 1-249-441-11 CARBON 100K 5% 1/4W (US,AND,MY,SP,JE,HK,AR,AUS,KR) 100K 5% 1/4W (US,AND,MY,SP,JE,HK,AR,AUS) $ $ 1-666-904-11 TRANS BOARD ************ 1-666-904-11 TRANS BOARD ************ < FUSE > < FUSE > 0 F1601 1-532-388-31 FUSE (T2AL/250V) 0 F1601 (MY,SP,JE,HK,AR,AUS) 1-532-388-31 FUSE (T2AL/250V) (MY,SP,JE,HK,AR,AUS,KR) 0 F1603 1-532-504-31 FUSE (T4AL/250V) 0 F1603 (MY,SP,JE,HK,AR,AUS) 1-532-504-31 FUSE (T4AL/250V) (MY,SP,JE,HK,AR,AUS,KR) 0 F1605 1-532-504-31 FUSE (T4AL/250V) 0 F1605 (MY,SP,JE,HK,AR,AUS) 1-532-504-31 FUSE (T4AL/250V) (MY,SP,JE,HK,AR,AUS,KR) < FUSE HOLDER > 113 $ $ $ < FUSE HOLDER > FH1601 1-533-293-11 FUSE HOLDER (MY,SP,JE,HK,AR,AUS) FH1601 1-533-293-11 FUSE HOLDER (MY,SP,JE,HK,AR,AUS,KR) FH1601 1-533-293-11 FUSE HOLDER (MY,SP,JE,HK,AR,AUS) FH1601 1-533-293-11 FUSE HOLDER (MY,SP,JE,HK,AR,AUS,KR) < SWITCH > 0S1600 1-762-753-11 SWITCH, VO;TAGE SELECTION 0S1600 (MY,SP,JE,HK,AR,AUS) < TRANSFORMER > 0 T1600 1-431-498-11 TRANSFORMER, POWER 0 T1600 (MY,SP,JE,HK,AR,AUS) $ $ < SWITCH > 1-762-753-11 SWITCH, VO;TAGE SELECTION (MY,SP,JE,HK,AR,AUS,KR) $ < TRANSFORMER > 1-431-498-11 TRANSFORMER, POWER (MY,SP,JE,HK,AR,AUS,KR) $ 3 HCD-MD333 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.1 1.0 Date Description of Revision 2001.06 Correction of exploded views. 1999.11 SUPPLEMENT-1 1998.08 New (SPM-01012)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 1998:07:31 13:11:59 Producer : Acrobat Distiller 3.0 for Power Macintosh Modify Date : 2001:06:07 10:32:09Z Title : HCD-MD333 Subject : US/Canadian/AEP/UK/E/Australian/Tourist Author : Sony Corporation Page Count : 92 Page Mode : UseThumbs Page Layout : SinglePageEXIF Metadata provided by EXIF.tools