STM32 LCD Development Board For GSM Applications
User Manual: olimex -
Open the PDF directly: View PDF 
.
Page Count: 19
| Download | |
| Open PDF In Browser | View PDF |
STM32-LCD development board Users Manual All boards produced by Olimex are ROHS compliant Revision Initial, May 2009 Copyright(c) 2009, OLIMEX Ltd, All rights reserved Page 1 INTRODUCTION: STM32-LCD is development prototype board with STM32F103ZE microcontroller from STMicroelectronics. This powerful microcontroller supports various serial interfaces such as USB, USART, SPI. In addition you will find also accelerometer, JTAG, TFT LCD, mini SD/MMC card connector on this board and most of the GPIOs are on extension headers where you can connect your additional circuits. All this allows you to build a diversity of powerful applications to be used in a wide range of situations. BOARD FEATURES: – Microcontroller – STM32F103ZE - high-performance ARM® Cortex™-M3 32-bit RISC core operating at a 72 MHz frequency, high-speed embedded memories (Flash memory - 512 Kbytes and SRAM - 64 Kbytes), and an extensive range of enhanced I/Os and peripherals connected to two APB buses. – JTAG connector – EXT connector – UEXT40 connector – UEXT1 connector – UEXT2 connector – EXT_PWR connector – Mini SD/MMC – Mini USB – LCD TFT 320x240 pixels coloured with touch screen – Power source connector – Accelerometer – 8 MHz crystal oscillator – Reset circuit – Clock circuit – PCB: FR-4, 1.5 mm (0,062"), soldermask, silkscreen component print – Dimensions 79.2x57.6 mm (3.12x2.27”) Page 2 ELECTROSTATIC WARNING: The STM32-LCD board is shipped in protective anti-static packaging. The board must not be subject to high electrostatic potentials. General practice for working with static sensitive devices should be applied when working with this board. BOARD USE REQUIREMENTS: Cables: The cable you will need depends on the programmer/debugger you use. If you use ARM-JTAG-EW, you will need USB A-B cable. Hardware: Programmer/Debugger ARM-JTAG-EW or other compatible programming/debugging tool if you work with EW-ARM. You can use also ARM-USB-OCD, ARM-USB-TINY, ARM-JTAG. or other compatible programming/debugging tool. PROCESSOR FEATURES: STM32-LCD use High-density performance line ARM-based 32-bit MCU with these features: – Core: ARM 32-bit Cortex™-M3 CPU – – – – – 72 MHz maximum frequency, 1.25 DMIPS/MHz (Dhrystone 2.1) performance at 0 wait state memory access – Single-cycle multiplication and hardware division Memories – 512 Kbytes of Flash memory – 64 Kbytes of SRAM – Flexible static memory controller with 4 Chip Select. Supports Compact Flash, SRAM, PSRAM, NOR and NAND memories – LCD parallel interface, 8080/6800 modes Clock, reset and supply management – 2.0 to 3.6 V application supply and I/Os – POR, PDR, and programmable voltage detector (PVD) – 4-to-16 MHz crystal oscillator – Internal 8 MHz factory-trimmed RC – Internal 40 kHz RC with calibration – 32 kHz oscillator for RTC with calibration Low power – Sleep, Stop and Standby modes – VBAT supply for RTC and backup registers 3 × 12-bit, 1 µs A/D converters (up to 21 channels) Page 3 – Conversion range: 0 to 3.6 V – Triple-sample and hold capability – Temperature sensor – 2 × 12-bit D/A converters – DMA: 12-channel DMA controller – – – Debug mode – Serial wire debug (SWD) & JTAG interfaces – Cortex-M3 Embedded Trace Macrocell™ 112 fast I/O ports – – – – Supported peripherals: timers, ADCs, DAC, SDIO, I2Ss, SPIs, I2Cs and USARTs 112 I/Os, all mappable on 16 external interrupt vectors, all 5 V-tolerant except for analog inputs 11 timers – four 16-bit timers, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input – 2 × 16-bit motor control PWM timers with dead-time generation and emergency stop – 2 × watchdog timers (Independent and Window) – SysTick timer: a 24-bit downcounter – 2 × 16-bit basic timers to drive the DAC 13 communication interfaces – 2 × I2C interfaces (SMBus/PMBus) – 5 USARTs (ISO 7816 interface, LIN, IrDA capability, modem control) – 3 SPIs (18 Mbit/s), 2 with I2S interface multiplexed – CAN interface (2.0B Active) – USB 2.0 full speed interface – SDIO interface CRC calculation unit, 96-bit unique ID Page 4 BLOCK DIAGRAM: MEMORY MAP: Page 5 Page 6 Page 7 DACOUT1 DACOUT2 3.3V VREF+ SPI1_ NSS SPI1_SCK +5V_USB PF15 PF13 PF11 PF9 PF7 PF5 PF3 PF1 USART1_TX I2C1_SCL1 SPI1 _MISO SPI1_SCK 3.3V PD12 PB2 PA1 +5V_USB PG 15 PG13 PG11 PG9 PG 7 PG 5 PG3 PG1 VBAT PE0 PE5 PC6 PC13 3 3.3V 10K RESET 1 GND EXT 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 BH40R 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 PF14 PF12 PF10 PF8 PF6 PF4 PF2 PF0 RST ADC12_IN8 ADC1 2_IN9 ADC12 _IN14 ADC12_IN15 USART1_RX I2C1_SDA1 SPI1_MOSI SPI1 _NSS VIN VIN RST PG14 PG 12 PG1 0 PG8 PG6 PG4 PG 2 PG0 RST PD6 PD11 USB_P PA8 PE1 PE6 PC7 PB5 100nF UEXT40 BH40R 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 R69 390R R19 0R R20 47R R40 C12 27pF Q1 8MHz C13 27p F 560R C28 C44 100nF 3.3V 2 U2 NA D5 2 VCC + 10K 3.3V_A C7 100nF 3.3V_A BAT54C R8 FB1 R15 C40 100nF C9 C8 100nF 1 00nF 56 57 87 88 89 90 91 92 93 124 125 126 127 128 129 132 10 11 12 13 14 15 18 19 20 21 22 49 50 53 54 55 PF0 PF1 PF2 PF3 PF4 PF5 PF6 PF7 PF8 PF9 PF10 PF11 PF12 PF13 PF14 PF15 25 106 24 23 138 6 30 31 32 33 PG 0 PG1 PG2 PG3 PG4 PG 5 PG6 PG7 PG8 PG9 PG 10 PG11 PG12 PG13 PG14 PG 15 RST R12 NA NA C79 VREF+ 100nF C47 C6 100nF 3.3V C45 100nF FB0805 C11 C5 100nF 10uF/6.3V C42 100nF 0 C39 100nF 3.3V_A C38 100nF 3 C23 100nF 1 GND GND ADJ 5 4 R16 47K/1% R14 330K/1 % C96 1 uF C10 STM32F1 03ZE(LQFP144) PF0/FSMC_A0 PF1/FSMC_A1 PF2/FSMC_A2 PF3/FSMC_A3 PF4/FSMC_A4 PF5/FSMC_A5 PF6/ADC3_IN4/FSMC_NIORD PF7/ADC3_IN5/FSMC_NREG PF8/ADC3_IN6/FSMC_NIOWR PF9/ADC3_IN7/FSMC_CD PF10/ADC3_IN8/FSMC_INTR PF11/FSMC_NIOS16 PF12/FSMC_A6 PF13/FSMC_A7 PF14/FSMC_A8 PF15/FSMC_A9 141 142 1 2 3 4 5 58 59 60 63 64 65 66 67 68 114 115 116 117 118 119 122 123 77 78 79 80 81 82 85 86 R54 BAT_PWR +5V_USB PE0 PE1 TFT_RST TFT_RS SENS_INT PE5 PE6 D4 D5 D6 D7 D8 D9 D10 D11 D12 Q2 NA 32768/6 pF D2 D3 SD_CMD DISC /O E /WE PD6 /NCE2 D13 D14 D15 PD11 PD12 TFT_LIG HT D0 D1 YD YU XL XR ADC12_IN14 ADC12_IN15 PC6 PC7 SD_D0 SD_D1 SD_D2 SD_D3 SD_CLK PC13 ADC12_ IN8 ADC12_IN9 PB2 TDO TRST PB5 I2 C1 _SCL1 I2C1_SDA1 I2C1_SCL 2 I2C1_SDA2 I2C2_SCL I2 C2_ SDA SPI2_NSS SPI2_SCK SPI2_MISO SPI2_MOSI 46 47 48 133 134 135 136 137 139 140 69 70 73 74 75 76 26 27 28 29 44 45 96 97 98 99 111 112 113 7 8 9 R104 USB_ P PA1 USART2_TX USART2_RX SPI1_NSS SPI1_SCK SPI1_MISO SPI1_MOSI PA8 USART1 _TX USART1_RX USBDM USBDP TMS TCK TDI 3.3V 34 35 36 37 40 41 42 43 100 101 102 103 104 105 109 110 GND 1 00nF C99 0R 3.3V_E EXT_PWR 1 2 3 4 5 6 CO N6 PE0/TIM4_ETR/FSMC_NBL0 PE1/FSMC_NBL1 PE2/TRACECK/FSMC_A23 PE3/TRACED0/FSMC_A19 PE4/TRACED1/FSMC_A20 PE5/TRACED2/FSMC_A21 PE6/TRACED3/FSMC_A22 PE7/FSMC_D4/TIM1_ETR PE8/FSMC_D5/TIM1_CH1N PE9/FSMC_D6/TIM1_CH1 PE10/FSMC_D7/TIM1_CH2N PE11/FSMC_D8/TIM1_CH2 PE12/FSMC_D9/TIM1_CH3N PE13/FSMC_D10/TIM1_CH3 PE14/FSMC_D11/TIM1_CH4 PE15/FSMC_D12/TIM1_BKIN PD0/OSC_IN/FSMC_D2/CANRX PD1/OSC_OUT/FSMC_D3/CANTX PD2/TIM3_ETR/UART5_RX/SDIO_CMD PD3/FSMC_CLK/USART2_CTS PD4/FSMC_NOE/USART2_RTS PD5/FSMC_NWE/USART2_TX PD6/FSMC_NWAIT/USART2_RX PD7/FSMC_NE1/FSMC_NCE2/USART2_CK PD8/FSMC_D13/USART3_TX PD9/FSMC_D14/USART3_RX PD10/FSMC_D15/USART3_CK PD11/FSMC_A16/USART3_CTS PD12/FSMC_A17/TIM4_CH1/USART3_RTS PD13/FSMC_A18/TIM4_CH2 PD14/FSMC_D0/TIM4_CH3 PD15/FSMC_D1/TIM4_CH4 PC0/ADC123_IN10 PC1/ADC123_IN11 PC2/ADC123_IN12 PC3/ADC123_IN13 PC4/ADC12_IN14 PC5/ADC12_IN15 PC6/I2S2_MCK/TIM8_CH1/SDIO_D6/TIM3_CH1 PC7/I2S3_MCK/TIM8_CH2/SDIO_D7/TIM3_CH2 PC8/TIM8_CH3/SDIO_D0/TIM3_CH3 PC9/TIM8_CH4/SDIO_D1/TIM3_CH4 PC10/UART4_TX/SDIO_D2/USART3_TX PC11/UART4_RX/SDIO_D3/USART3_RX PC12/UART5_TX/SDIO_CK/USART3_CK PC13/TAMPER-RTC PC14/OSC32_IN PC15/OSC32_OUT PB0/ADC12_IN8/TIM3_CH3/TIM8_CH2N/TIM1_CH2N PB1/ADC12_IN9/TIM3_CH4/TIM8_CH3N/TIM1_CH3N PB2/BOOT1 PB3/TRACESWO/JTDO/SPI3_SCK/I2S3_CK/TIM2_CH2/SPI1_SCK PB4/JNTRST/SPI3_MISO/TIM3_CH1/SPI1_MISO PB5/I2C1_SMBAI/SPI3_MOSI/I2S3_SD/TIM3_CH2/SPI1_MOSI PB6/I2C1_SCL/TIM4_CH1/USART1_TX PB7/I2C1_SDA/FSMC_NL/TIM4_CH2/USART1_RX PB8/TIM4_CH3/SDIO_D4/I2C1_SCL/CANRX PB9/TIM4_CH4/SDIO_D5/I2C1_SDA/CANTX PB10/I2C2_SCL/USART3_TX/TIM2_CH3 PB11/I2C2_SDA/USART3_RX/TIM2_CH4 PB12/SPI2_NSS/I2S2_WS/I2C2_SMBAI/USART3_CK/TIM1_BKIN PB13/SPI2_SCK/I2S2_CK/USART3_CTS/TIM1_CH1N PB14/SPI2_MISO/USART3_RTS/TIM1_CH2N PB15/SPI2_MOSI/I2S2_SD/TIM1_CH3N PA0/WKUP/USART2_CTS/ADC123_IN0/TIM5_CH1/TIM2_CH1_ETR/TIM8_ETR PA1/USART2_RTS/ADC123_IN1/TIM5_CH2/TIM2_CH2 PA2/USART2_TX/TIM5_CH3/ADC123_IN2/TIM2_CH3 PA3/USART2_RX/TIM5_CH4/ADC123_IN3/TIM2_CH4 PA4/SPI1_NSS/DAC_OUT1/USART2_CK/ADC12_IN4 PA5/SPI1_SCK/DAC_OUT2/ADC12_IN5 PA6/SPI1_MISO/TIM8_BKIN/ADC12_IN6/TIM3_CH1/TIM1_BKIN PA7/SPI1_MOSI/TIM8_CH1N/ADC12_IN7/TIM3_CH2/TIM1_CH1N PA8/USART1_CK/TIM1_CH1/MCO PA9/USART1_TX/TIM1_CH2 PA10/USART1_RX/TIM1_CH3 PA11/USART1_CTS/CANRX/TIM1_CH4/USBDM PA12/USART1_RTS/CANTX/TIM1_ETR/USBDP PA13/JTMS-SWDIO PA14/JTCK-SWCLK PA15/JTDI/SPI3_NSS/I2S3_WS/TIM2_CH1_ETR/SPI1_NSS MCP1825-ADJE/DC 3 6 #SHDN VIN VOUT VR1 PG0/FSMC_A10 PG1/FSMC_A11 PG2/FSMC_A12 PG3/FSMC_A13 PG4/FSMC_A14 PG5/FSMC_A15 PG6/FSMC_INT2 PG7/FSMC_INT3 PG8 PG9/FSMC_NE2/FSMC_NCE3 PG10/FSMC_NCE4_1/FSMC_NE3 PG11/FSMC_NCE4_2 PG12/FSMC_NE4 PG13/FSMC_A24 PG14/FSMC_A25 PG15 NRST NC OSC_OUT OSC_IN BOOT0 VBAT VSSA VREF- VREF+ VDDA VSS_1 VSS_2 VSS_3 VSS_4 VSS_5 VSS_6 VSS_7 VSS_8 VSS_9 VSS_10 VSS_11 VDD_1 VDD_2 VDD_3 VDD_4 VDD_5 VDD_6 VDD_7 VDD_8 VDD_9 VDD_10 VDD_11 U1 10K 2 + 71 107 143 38 16 51 61 83 94 120 130 72 108 144 39 17 52 62 84 95 121 131 100 nF C100 1 C15 10pF C14 10pF GND 10K 1 B1 _0/B1_1 3 22R 47pF(NA) 3.3V 3.3V 3.3V SD_CLK SD_D0 SD_D1 SD_D2 SD_D3 SD_CMD 2 10K R147 10K R155 NA R106 R100 R105 3.3V R10 7 33K 33K 33K 33K L5 470 nH 3 .3V R41 1M 100 nF 10K 10K +5V_J-LINK R153 R154 SD_CLK SD_D0 SD_D1 SD_D2 47uF/6.3V C20 SD_D3 SD_CMD 9 11 2 3 6 4 5 7 8 1 10 12 VBUS DD+ ID GND 1 3 5 7 9 11 13 15 17 19 BH20R JATG 10nF C80 MICRO_SD_CARD_holder CP1 CP2 CD/DAT3/CS CMD/DI VSS VDD CLK/SCLK DAT0/DO DAT1/RES DAT2/RES WP1 WP2 USD 10K R151 R150 10K SD/MMC CARD R-T 1 R149 R148 10K R10 2 0K C33 C58 +5V_USB USBLC6-2P6 U9 USB_P R9 10K 1 2 3 6 5 4 DISC 100nF C32 3 .3V R152 10K R22 R21 2K R38 3 .3V R10 8 33K TRST TDO RST TRST TDI TMS TCK 47pF(NA) C17 USBDM C16 22R 3.3V R51 1 .5K USBDP Q3 BC807 R36 47K/1% USB CIRCUIT 10uF/6.3V B0_1/B0_0 C97 R17 100uF/6.3V/tant 3 .3V 1N5819S D2 3.3V + GND3 VBAT 1N5 819S D1 POWER SUPPLY CIRCUIT 2 4 6 8 10 12 14 16 18 20 MINI_USB USB GND4 USB 0R 1N5819S D3 1 00uF/6 .3V/tant 1N5 819S D4 + 3.3V_MCU_E RF1 RF110_SMD +5V_USB +5V_J-LINK BAT_PWR GND2 GND1 3.3V 1 2 4V_MIN-6V_MAX PWR VIN 3.3V TFT_RST /NCE2 TFT_RS /WE /OE R7 NA R3 NA 5 DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 DB9 DB10 DB11 DB12 DB13 DB14 DB15 #RESET #CS RS #WR #RD TFT GND LEDK1 LEDK2 LEDK3 LEDK4 LEDK5 LEDA LEDA YD XL YU XR GND GND VCC VCC FS-K320QVB-V1 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 6 7 8 4 2 4 6 8 10 100nF UEXT1 0R BH10R 1 3 5 7 9 C18 UEXT1_3.3V UEXT1 2 4 6 8 10 100n F UEXT2 0R BH10R 1 3 5 7 9 C19 UEXT2_3.3V http://www.o limex.com/dev COPYRIG HT(C), 200 9 Rev. Initial STM32-LCD D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 R2 NA 3.3V 3.3V 3.3V 10 12 15 8 1 6 5 3 2 U10 RES_1 RES_2 RES_3 GND GND1 GND2 VDD_IO CS NC SCL/SPC SDA/SDI/SDO SDO VDD VDD1 CK RDY/INT 9 14 16 11 13 4 7 37 30 31 32 33 34 35 36 26 27 28 29 1 25 2 3 0R 3.3V C72 TFT_LIGHT FET1 IRLML640 2 100nF C3 3.3V R13 33K 3.3V R50 1.5K R1 100K 3.3V 100nF R12 0 33K 3.3V 100nF C1 R_LCD YD XL YU XR USART1_RX I2C1_SDA1 SPI1_MOSI SPI1_NSS 3.3V R11 4.7K R11 9 4.7K USART2_RX I2C1_SDA2 SPI2 _MOSI SPI2_NSS 3.3V LIS3LV02DL-TR(LGA16) 2K UEXT2 560R R6 4.7K USART1_TX I2C1_SCL1 SPI1_MISO SPI1_SCK 3.3V R90 R91 R4 4.7K R11 8 4.7K USART2_TX I2C1_SCL 2 SPI2 _MISO SPI2_SCK 3.3V SENS_INT I2 C2_SCL I2C2_SDA R5 4.7K 3.3V3.3V 3.3V ACCELEROMETER SCHEMATIC: + 2 BOARD LAYOUT POWER SUPPLY CIRCUIT: STM32-LCD can take power from four sources: – Power connector – 4V – 6V DC. – BAT_PWR from EXT_PWR – 4V DC. – +5V_J-LINK from JTAG connector – +5V_USB from USB connector The programmed board power consumption is about 200 mA. RESET CIRCUIT: STM32-LCD reset circuit includes R8 (10k), R69 (560 Ohm), C28 (100nF) pin 15 of JTAG connector, EXT pin 32, UEXT40 pin 32 and STM32F103ZE pin 25 (NRST). CLOCK CIRCUIT: Quartz crystal 8 MHz is connected to STM32F103ZE pin 23 (OSC_IN) and pin 24 (OSC_OUT). Quartz crystal 32.768 kHz is connected to STM32F103ZE pin 8 (PC14/OSC32_IN) and pin 9 (PC15/OSC32_OUT). Page 8 JUMPER DESCRIPTION: R-T Connect RST with TRST. Default state is open. UEXT1_3.3V This jumper when closed, supplies 3.3 V voltage to UEXT1 pin 1. Default state is closed. UEXT2_3.3V 3.3V_E This jumper when closed, supplies 3.3 V voltage to UEXT2 pin 1. Default state is closed. This jumper, when closed, enable the main 3.3 V regulator VR1 - MCP1825-ADJE/DC. Default state is closed. 3.3V_MCU_E This jumper, when closed, enables STM32F103ZE 3.3 V power supply. Default state is closed. R_LCD You can use this jumper, when it's open, to measure the current of LCD backlight. Default state is closed. B0_1/B0_0 Select BOOT0 Boot mode. Default state is in position B0_0. B1_0/B1_1 Select BOOT1 Boot mode. Default state – B1_0 – not shorted and B1_1 – not shorted. Boot mode selection pins Boot Mode Aliasing BOOT1 BOOT0 x 0 Main Flash memory Main Flash memory is selected as boot space 0 1 System memory System memory is selected as boot space 1 1 Embedded SRAM Embedded SRAM is selected as boot space INPUT/OUTPUT: – LCD TFT 320x240 pixels coloured with touch screen. Page 9 EXTERNAL CONNECTORS DESCRIPTION: UEXT1 Pin # Signal Name 1 3.3V 2 GND 3 USART1_TX 4 USART1_RX 5 I2C1_SCL1 6 I2C1_SDA1 7 SPI1_MISO 8 SPI1_MOSI 9 SPI1_SCK 10 SPI1_NSS UEXT2 Pin # Signal Name 1 3.3V 2 GND 3 USART2_TX 4 USART2_RX 5 I2C1_SCL2 6 I2C1_SDA2 7 SPI2_MISO 8 SPI2_MOSI 9 SPI2_SCK 10 SPI2_NSS EXT Page 10 Pin # Signal Name Pin # Signal Name 1 3.3 V 2 GND 3 PE0 4 PE1 5 PE5 6 PE6 7 PC6 8 PC7 9 PC13 10 PB5 11 3.3 V 12 GND 13 +5V_USB 14 VIN 15 PG15 16 PG14 17 PG13 18 PG12 19 PG11 20 PG10 21 PG9 22 PG8 23 PG7 24 PG6 25 PG5 26 PG4 27 PG3 28 PG2 29 PG1 30 PG0 31 VBAT 32 RST 33 GND 34 PD6 35 PD12 36 PD11 37 PB2 38 USB_P 39 PA1 40 PA8 Page 11 UEXT40 Pin # Signal Name Pin # Signal Name 1 3.3 V 2 GND 3 USART1_TX 4 USART1_RX 5 I2C1_SCL1 6 I2C1_SDA1 7 SPI1_MISO 8 SPI1_MOSI 9 SPI1_SCK 10 SPI1_NSS 11 3.3 V 12 GND 13 +5V_USB 14 VIN 15 PF15 16 PF14 17 PF13 18 PF12 19 PF11 20 PF10 21 PF9 22 PF8 23 PF7 24 PF6 25 PF5 26 PF4 27 PF3 28 PF2 29 PF1 30 PF0 31 3.3V_A 32 RST 33 AGND 34 ADC12_IN8 35 VREF+ 36 ADC12_IN9 37 SPI1_NSS 38 ADC12_IN14 39 SPI1_SCK 40 ADC12_IN15 Page 12 JTAG: The JTAG connector allows the software debugger to talk via a JTAG (Joint Test Action Group) port directly to the core. Instructions may be inserted and executed by the core thus allowing STM32F103ZE memory to be programmed with code and executed step by step by the host software. Pin # Signal Name Pin # Signal Name 1 3.3V 2 3.3V 3 TRST 4 GND 5 TDI 6 GND 7 TMS 8 GND 9 TCK 10 GND 11 pull-down 12 GND 13 TDO 14 GND 15 RST 16 GND 17 pull-down 18 GND 19 +5V J-LINK 20 GND Page 13 USB Pin # Signal Name 1 +5V_USB 2 USBDM 3 USBDP 4 NC 5 GND PWR Pin # Signal Name 1 VIN (4 – 6) V DC 2 GND SD/MMC Pin # Signal Name 1 SD_D2 2 SD_D3 3 SD_CMD 4 VDD (3.3V) 5 SD_CLK 6 GND 7 SD_D0 8 SD_D1 9 Not connected 10 Not connected 11 Not connected 12 Not connected Page 14 SPI Up to three SPIs are able to communicate up to 18 Mbits/s in slave and master modes in full-duplex and simplex communication modes. The 3-bit prescaler gives 8 master mode frequencies and the frame is configurable to 8 bits or 16 bits. The hardware CRC generation/verification supports basic SD Card/MMC modes. All SPIs can be served by the DMA controller. I2S Two standard I2S interfaces (multiplexed with SPI2 and SPI3) are available, that can be operated in master or slave mode. These interfaces can be configured to operate with 16/32 bit resolution, as input or output channels. Audio sampling frequencies from 8 kHz up to 48 kHz are supported. When either or both of the I2S interfaces is/are configured in master mode, the master clock can be output to the external DAC/CODEC at 256 times the sampling frequency. I2C Up to two I²C bus interfaces can operate in multimaster and slave modes. They can support standard and fast modes. They support 7/10-bit addressing mode and 7-bit dual addressing mode (as slave). A hardware CRC generation/verification is embedded. They can be served by DMA and they support SMBus 2.0/PMBus. Page 15 MECHANICAL DIMENSIONS Page 16 AVAILABLE DEMO SOFTWARE – STM32-LCD-DEMO Page 17 ORDER CODE: STM32-LCD - assembled and tested board How to order? You can order to us directly or by any of our distributors. Check our web www.olimex.com/dev for more info. Revision history: Revision Initial, May 2009 Page 18 Disclaimer: © 2009 Olimex Ltd. All rights reserved. Olimex®, logo and combinations thereof, are registered trademarks of Olimex Ltd. Other terms and product names may be trademarks of others. The information in this document is provided in connection with Olimex products. No license, express or implied or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Olimex products. Neither the whole nor any part of the information contained in or the product described in this document may be adapted or reproduced in any material from except with the prior written permission of the copyright holder. The product described in this document is subject to continuous development and improvements. All particulars of the product and its use contained in this document are given by OLIMEX in good faith. However all warranties implied or expressed including but not limited to implied warranties of merchantability or fitness for purpose are excluded. This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product. Page 19
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 19 Language : bg-BG XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:5aab22df-ed45-45df-9759-d4cd52e6b56d Producer : OpenOffice.org 3.1 Create Date : 2010:12:13 09:31:35+02:00 Creator Tool : Writer Modify Date : 2010:12:13 09:55:10+02:00 Metadata Date : 2010:12:13 09:55:10+02:00 Document ID : uuid:c709dfc9-4895-4e92-bc24-7ca172a4d980 Format : application/pdf Title : STM32-LCD development board for GSM applications Creator : OLIMEX LTD Description : Development board for STM32F103ZE Author : OLIMEX LTD Keywords : stm32f103ze, development, board, prototype, board Subject : Development board for STM32F103ZEEXIF Metadata provided by EXIF.tools