Titan Assembly Guide

User Manual:

Open the PDF directly: View PDF PDF.
Page Count: 5

DownloadTitan Assembly Guide
Open PDF In BrowserView PDF
6

5

4

3
ITEM
12

ASSEMBLY OVERVIVEW
D

13
14

QTY
1
1
1

15
16
17

2
PARTS LIST
PART NUMBER

1

M4 x 10
M4 Hex Nut

DESCRIPTION
M3 x 8 Dome Head Socket Cap Screw
M4 x 10 Dome Head Socket Cap Screw
M4 Hex Nut

1

EX_SPRING

Extruder Idler Spring

1

EX_PINION
EX_BRACKET

Extruder Pinion Gear (Steel)

1

M3 x 8

D

Extruder Bracket - Printed Example

NOTE: A SPACER IS ALWAYS REQUIRED

NOTE: THESE DRAWINGS ARE FOR REFERENCE ONLY.
REFER TO http://wiki.e3d-online.com/wiki/Titan_Assembly FOR ASSEMBLY INFORMATION

1. THICKNESS: 2 MIN - 4.5 MAX
2. MAX ASSUMES MOTOR SHAFT LENTH 22.2
3. SUPPLIED FIXINGS FOR THICKNESS OF 2

C

C

16

13
14
15

B

B

17
12

Copyright (C) E3D-Online Ltd (e3d-online.com)
These drawings are free hardware: you can redistribute it and/or modify it under the terms of the GNU General Public License as
published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.
Designed by

A

Checked by

Approved by

Date

E3D Online - JR

Date
16/02/2016

A

E3D Titan - Supplementary Drawings
ASM_EX_2
6

5

4

3

2

Edition
1

Sheet
8 / 13

PARTS LIST

ASSEMBLY STEPS 1-4

ITEM QTY
PART NUMBER
12
1 M3 x 8
1 M3 x 4 Grub Screw
26

DESCRIPTION
M3 x 8 Dome Head Socket Cap Screw
M3 x 4 Socket Set Screw

NOTE:
The gear must go on the correct way around.
The grub screw hole must be towards the motor face.
26

THE TOP SURFACES OF THE
TWO GEARS MUST BE FLUSH
ADJUST THE PINION ACCORDINGLY

12
Assembly Steps:
1.
2.
3.
4.

Present motor up to mounting bracket.
Present body to mounting bracket and install the M3 x 8 Screw to hold the body in place
Fit the small pinion gear onto the motor shaft.
Fit the large gear into the bearing on the body and use this to set the position of the pinion gear.
Tighten up the grub screw on the pinion gear.

Copyright (C) E3D-Online Ltd (e3d-online.com)
These drawings are free hardware: you can redistribute it and/or modify it under the terms of the GNU General Public License as
published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.
Designed by

Checked by

Approved by

Date

E3D Online - JR

Date
16/02/2016

E3D Titan - Supplementary Drawings
ASM_EX_2

Edition

Sheet
9 / 13

PARTS LIST

ASSEMBLY STEPS 5-8

ITEM QTY
PART NUMBER
14
1 M4 Hex Nut
1 M4 x 10
13
27
1 PTFE

DESCRIPTION
M4 Hex Nut
M4 x 10 Dome Head Socket Cap Screw

16

14

13

Assembly Steps:
5.

Note:

Install the filament guide and HotEnd into the extruder body.
For the 1.75mm version, make sure the PTFE goes all the
way up into the filament guide. See cutout below.
Rotate the HotEnd if necessary to insert.
The diagram shows a bowden adaptor for a bowden setup,
if you are using a direct, there will be a HotEnd in place of this part.

Assembly Steps:
6.
7.
8.

Slide the lever onto the motor shaft.
Screw the M4 Nut fully onto the M4 x 10 Screw
Slide the spring onto the screw and insert the assembly into the slot as shown.

Note:

This bit is fiddly. Don't add any tension to the spring,
it will fly across the room to be lost forever.

Copyright (C) E3D-Online Ltd (e3d-online.com)
These drawings are free hardware: you can redistribute it and/or modify it under the terms of the GNU General Public License as
published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.
Designed by

Checked by

Approved by

Date

E3D Online - JR

Date
16/02/2016

E3D Titan - Supplementary Drawings

27
ASM_EX_2

Edition

Sheet
10 / 13

PARTS LIST

ASSEMBLY STEP 9

ITEM QTY
PART NUMBER
29
1 M3 x 25
30
3 M3 x 30

Assembly Steps:
9.

DESCRIPTION
M3 x 25 Low Head Socket Cap Screw
M3 x 30 Low Head Socket Cap Screw

The lid is held on with 4 screws. Note the bottom right screw is shorter than the others.

30

29

Copyright (C) E3D-Online Ltd (e3d-online.com)
These drawings are free hardware: you can redistribute it and/or modify it under the terms of the GNU General Public License as
published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.
Designed by

Checked by

Approved by

Date

E3D Online - JR

Date
16/02/2016

E3D Titan - Supplementary Drawings
ASM_EX_2

Edition

Sheet
11 / 13

19.5

TITAN EXTRENAL DIM'S

11.1

25

4.6

13.5

2 MIN

27

11.4

Copyright (C) E3D-Online Ltd (e3d-online.com)
These drawings are free hardware: you can redistribute it and/or modify it under the terms of the GNU General Public License as
published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version.
Designed by

Checked by

Approved by

Date

E3D Online - JR

Date
16/02/2016

E3D Titan - Supplementary Drawings
ASM_EX_2

Edition

Sheet
12 / 13
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Count                      : 5
Page Mode                       : UseOC
Page Layout                     : SinglePage
EXIF Metadata provided by EXIF.tools

Navigation menu