S.G_TM4060_BOOK Travel Mate 4060 Travelmate

4060 to the manual b06535fc-05c6-4880-a76e-defa7cc26f5f

User Manual: TravelMate 4060

Open the PDF directly: View PDF .
Page Count: 99

Download
Open PDF In Browser	View PDF

TravelMate 4060 Series
Service Guide

Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw

PRINTED IN TAIWAN

Revision History
Please refer to the table below for the updates made on TravelMate 4060 service guide.

Date
200512/27

Chapter
Chapter 1

Updates
Revise memory specification to 533MHz on page 19.

2006/01/17

Chapter 1

Update LCD panel specification on page 25.

2006/02/15

Chapter 3

Revise disassembling SOP on chapter 3.

2006/9/18

Chapter 6

Revise touchpad board to main board FFC part number.

Copyright
Copyright © 2005 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.

Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.

Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.

III

Conventions
The following conventions are used in this manual:

SCREEN MESSAGES

Denotes actual messages that appear
on screen.

NOTE

Gives bits and pieces of additional
information related to the current
topic.

WARNING

Alerts you to any damage that might
result from doing or not doing specific
actions.

CAUTION

Gives precautionary measures to
avoid possible hardware or software
problems.

IMPORTANT

Reminds you to do specific actions
relevant to the accomplishment of
procedures.

Preface
Before using this information and the product it supports, please read the following general information.
1.

This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.

Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.

Table of Contents
Chapter 1

System Introduction 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Closed front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Left view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Right view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Bottom view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Easy-Launch Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Using the keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Lock keys and embedded numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Touchpad basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Chapter 2

System Utilities

BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
BIOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Create Crisis Recovery Diskette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Recover BIOS from Crisis Recovery Diskette . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Chapter 3

Machine Disassembly and Replacement

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Removing the HDD Module/the Memory and the Wireless LAN Card/
the Thermal Module and the CPU/ODD Module and LCD Module . . . . . . . . . . . . . .47
Removing the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Removing the Memory and the Wireless LAN Card . . . . . . . . . . . . . . . . . . . . . .47
Removing the Thermal Module and CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Removing the ODD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Disassembling the Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Separate the Main Unit Into the Upper and the Lower Case Assembly . . . . . . .51
Disassembling the Upper Case Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Disassembling the Lower Case Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

VII

Table of Contents
Disassembling the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Disassembling the External Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Disassembling the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Disassembling the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

Chapter 4

Troubleshooting

System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
External Diskette Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
External CD-ROM Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Keyboard or Auxiliary Input Device Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Memory check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Power System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Touchpad Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Power-On Self-Test (POST) Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Phoenix BIOS Beep Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Chapter 6

FRU (Field Replaceable Unit) List

TravelMate 4060 Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Please notice that Chapter 5 has been combined to Chapter 1.

VIII

Chapter 1

System Introduction
Features
This computer was designed with the user in mind. Here are just a few of its many features:

Platform
T

Intel® Pentium® M 730/740/750/760/770/780 processor (2MB L2 cache, 1.60/1.73/1.86/2/2.13/
2.26 GHz, 533 MHz FSB)

Intel® Pentium® M 725 processor (2MB L2 Cache, 1.60 GHz, 400 MHz FSB)

Intel Celeron M processor 360/370/380 (1 MB L2 cache, 1.40/1.50/1.60 GHz, 400 MHz FSB)

Chipset: Intel® 915GM

256 MB/512 MB of DDRII 533 memory, upgradeable to 2 GB with dual so DIMM modules

Memory

Data storage
T

40/60/80/100 GB ATA/100 hard disk

DVD-Dual double-layer drive

DVD/CD-RW combo drive

Display and graphics
T

Color Thin-Film Transistor (TFT) LCD displaying at
-- 15” XGA (1024 X 768)

-- 15.4” WXGA (1280 X 800) supporting simultaneous multi-window viewing on dual displays via
Acer GridVista
T

Intel® 915GM integrated 3D graphics, featuring Intel Graphics Media Accelerator 900 and up to
128 MB of shared memory

Microsoft® DirectX® 7.0 and dual independent display support

MPEG-2/DVD hardware-assisted capability

Simultaneous LCD and CRT display with LCD panel resolution at 70 Hz

Communication
T

Modem: 56K ITU V.92 modem with PTT approval; Wake-on-Ring ready

LAN: 10/100 Mbps Fast Ethernet; Wake-on-LAN ready

Wireless LAN (optional): integrated miniPCI Acer InviLinkTM 802.11b/g Wi-Fi CERTIFIEDTM
solution

Acer SignalUP wireless technology support

Wireless PAN (optional): integrated Bluetooth®

Audio system with two built-in speakers

Sound Blaster ProTM and MS-Sound compatible

Built-in microphone

Audio

Chapter 1

Input devices
T

88-/89-key Acer FineTouchTM keyboard

Touchpad with 4-way integrated scroll button

Four easy-launch buttons

Two front-panel buttons: wireless LED-button and Bluetooth® LED-button

I/O interface

Three USB 2.0 ports

Ethernet (RJ-45) port

Modem (RJ-11) port

External display (VGA) port

Microphone

Line-in jack

Headphones/speaker/line-out port

One Type II PC Card slot

DC-in jack for AC adaptor

TravelMate 4060

System Block Diagram

CPU CORE
SENTECH
SC451ITSTR

SYSTEM 3V/5V
MAXIM
MAX1999

Page:23

Page:24

+3VPCU
+3V_S5/+3VSUS
+3V
+5VPCU
+5VSUS
+5V
+15V

+1.8VSUS
+1.8V
NCP5214

+0.9VSUS
ON
+0.9V

+1.5V
SENTECH
SC1470

SENTECH
SC4215

SENTECH
SC1565

SI9183-AD

+1.5V_S5

+2.5V

+1.05V
Page:25

Page:26

BATTERY CHARGER
MAXIM
MAX8724

MIC IN
Page: 19

CLOCK GEN
ICS954206
Page:4

Page: 10

DDR-II SODIMM1

DDR-II SODIMM2
Page: 10

PATA HDD
Page: 16

IDE-ODD
Page: 16

AUDIO CODEC

DDR-II

FLASH

Page: 22

FAN

CRT

Page: 11

LVDS

Page: 11

TYPE II
SLOT

Page: 18

Page: 17

RJ45

Acer Incorporated

Document Number

Tuesday, August 09, 2005

BLOCK DIAGRAM

Sheet

PROJECT:Lugano II

Page:16

Bluetooth
USB
interface

USB4

Date:

Size

Page: 17

AD24
REQ0# / GNT0#
INTA#

REALTEK
RTL8100CL

Page: 16

AD20
REQ2# / GNT2#
INTB# , INTD#

MINI-PCI
Wireless LAN

Page: 18

AD17
REQ1# / GNT1#
INTC#

TI PCMCIA
PCI1510A ( L-F )

Page: 16

(Option)

Page: 21

Page:16

RGB

SYSTEM
USB PORT *3

MINI-PCIE slot
Wireless LAN

PCI-E BUS

PCI BUS 33MHZ

Page: 22

Keyboard

USB 2.0

Page: 22

Touchpad

USB2,3,5

LVDS

TM4060/AS1640(ZL8 for Quanta project code)

SB
INTEL
ICH6-M

DMI I/F

Page: 5, 6 , 7, 8

NB
INTEL
ALVISO 915GM

HOST BUS 533/400MHZ

Page:2, 3

INTEL Mobile_479 CPU

CELERON-M/PENTIUM-M

ATA 66/100

HD Audio
Page: 12 , 13 , 14

LPC 33MHZ

Page: 21

RJ11

KBC
NS
PC97551

Page: 17

Page: 19

MODEM

Page: 19

Realtek
ALC260 (ALC883)

AMP

Page: 20

MAX9755

Page: 20

LINE OUT

Page: 20

SPEAKER

Rev
3A

Chapter 1

Board Layout
Top View

TravelMate 4060

Bottom View

SW1

Lid Switch

CN1

CN2

Launch Board Connector

CN3

Modem Connector

CN7

Keyboard Connector

CN4

Bluetooth Module Connector

CN5

Touchpad Board Connector

CN6

Internal Microphone Connector

U17

Clock Generator

PCMCIA Connector

CN9

MDC Connector

CN11

Internal Speaker Connector

CN13

Power Jack

CN12

CRT Connector

CN14

Battery Connector

CN15

Optical Disk Drive Connector

CN17

RJ45 & RJ11 Connector

CN26

Wireless LAN Controller

U11

North Bridge

U13

CPU Socket

Chapter 1

LCD Connector

CN20

USB Connector

CN21

USB Connector

U19

BIOS ROM

EC PC97551 (Power and I/O
Connector)

CN22

RTC Battery

CN18

Memory Socket 1

LAN Chipset RTL8100CL

CN19

Memory Socket 2

U18

South Bridge

CN24

PCMCIA Connector

CN25

HDD Connector

CN27

USB Connector

CN28

Line-out/SPEDIF Jack

CN29

Microphone Jack

CN30

Line-in Jack

SW3

WLAN Button

SW2

Bluetooth Button

LED2

Charger LED

LED1

Power LED

U22

Audio Codec

U10

Fan Connector

TravelMate 4060

Panel
This is a brief introduction to the I/O ports, the features and the indicators.

Front view

Item

Description

Display screen

Also called LCD (Liquid Crystal Display), displays computer
output.

Microphone

Internal microphone for sound recording.

Keyboard

For entering data into you computer.

Palmrest

Comfortable support area for your hands when you use the
computer.

Click buttons (Left, center and right)

The left and right buttons function like the left and right
mouse buttons; the center button serves as a 4-way scroll
button.

Touchpad

Touch-sensitive pointing device which functions like a
computer mouse.

Status indicators

LEDs (Light Emitting Diodes) that turn on and off to show
the status of the computer and its functions and
components.

Easy-Launch buttons

Buttons for launching frequently used programs.

Power button

Turns the computer on and off.

Chapter 1

Closed front view

Description
Left and right speakers deliver stereo audio
output.

Power indicator

Lights up when the computer is on.

Battery indicator

Lights up when the battery is being charged.

Bluetooth communication button/
indicator

Press to enable/disable the Bluetooth function.
Indicates the status of Bluetooth communication
(optional).

7
#

Item/ Port
Speakers

5
Item

Icon

Item

Wireless communication button/
Description
indicator

Press to enable/disable the wireless function.
Indicates the status of wireless LAN
communication (optional).

Line-in jack

Accepts audio line-in devices (e.g., audio CD
player, stereo walkman).

Microphone jack

Accepts inputs from external microphones.

Description

Speaker/Line-Out/Headphone jack

Connects to audio line-out devices (e.g.,
speakers, headphones).

USB 2.0 port

Connects to Universal Serial Bus (USB) 2.0
devices (e.g., USB mouse, UsB camera).

Left view

TravelMate 4060

Icon

Item/ Port

Description

Optical drive

Internal optical drive; accepts CDs or DVDs
depending on the optical drive type.

LED indicator

Lights up when the optical drive is active.

Optical drive eject button

Ejects the optical drive tray from the drive.

Emergency eject hole

Ejects the optical drive tray when the computer is
turned off.

Right view

Icon

Item/ Port

Description

PC Card slot eject button

Ejects the PC Card from the slot

PC card slot

Accepts one Type II CardBus PC Card.

Two USB 2.0 ports

Connects to Universal Serial Bus (USB) 2.0
devices (e.g., USB mouse, USB camera).

Network jack

Connects to an Ethernet 10/100 based
network.

Modem jack

Connects to a phone line.

Ventilation slots

Enable the computer to stay cool, even after
prolonged use.

Rear view

Chapter 1

Icon

Port

Description

Power jack

Connects to an AC adaptor.

External display port

Connects to a display device (e.g., external
monitor, LCD projector).

Security keylock

Connects to a Kensington-compatible
computer security lock.

Bottom view

#
1

Item
Hard disc bay

Description
Houses the computer’s hard disc (secured by a screw).

Battery release latch

Unlatches the battery to remove the battery pack.

Battery bay

Houses the computer’s battery pack.

Battery lock

Locks the battery in place.

Cooling fan

Helps keep the computer cool.
Note: Do not cover or obstruct the opening of the fan.

Memory comparment

House the computer’s main memory.

TravelMate 4060

Indicators
The computer has three easy-to-read status icons on the upper-right above the keyboard, and four on the front
panel.

Icon

Function

Icon

Description

Function

Description

Caps Lock

Lights when Caps Lock is activated.

Num Lock

Lights when Numeric Lock is activated.

Media activity

Indicates when the hard disk or optical
drive is active.

Power

Lights when the computer is on.

Battery

Lights when the battery is being charged.

Bluetooth

Indicates the status of Bluetooth
communication.

Wireless LAN

Indicates the status of Bluetooth
communication.

NOTE: 1. Charging: the light shows amber when the battery is charging.
NOTE: 2. Fully charged: light shows green when in AC mode.

Chapter 1

ction

Function

Hot Key

Icon

Function

Description

Fn-F1
Description

Easy-Launch Buttons
Fn-F2

Located at the upper-right, above the keyboard are four buttons. These buttons are called launch keys. They
are mail, Web browser, Acer Empowering key “

eManager" on page 23

"Acer
“, and
one user-programmable button.

"Acer
“ to run
the Acer eManager. The mail and Web buttons are pre-set ot email and internet programs,
but can be reset by users. To set the Web browser, mail and programmable keys, run the Acer Launch
Manager.

Fn-F3 Press “
eManager" on page 23

"Acer eManager" on page
23

Fn>
"Acer eManager" on page
23

Fn-F4

Description
Launch key

Default application

User-programmable
Acer eManager (user-programmable)
"Acer

eManager" on page 23

Web browser

Internet browser (user-programmable)

Mail

Email application (user-programmable)

"Acer eManager" on page
23

TravelMate 4060

Using the keyboard
The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and
twelve function keys.

Lock keys and embedded numeric keypad
The keyboard has three lock keys which you can toggle on and off.

Lock key
Caps Lock

Description
When @is on, all alphabetic characters typed are in uppercase.

@
Num Lock +

]

When ] is on, the embedded keypad is in numeric mode. The keys function
as a calculator (complete with the arithmetic operators ), -, *, and /). Use this mode
when you need to do a lot of numeric data entry. A better solution would be to
connect an external keypad.

Scroll Lock +

When [ is on, the screen moves one line up or down when you press the up

[

or down arrow keys respectively. [ does not work with some applications.

The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.

Desired access

Num lock on

Num lock off

Number keys on embedded
keypad

Type numbers in a normal manner.

Cursor-control keys on embedded
keypad

Hold while using cursor-control
keys.

Hold while using cursorcontrol keys.

Main keyboard keys

Hold while typing letters on embedded
keypad.

Type the letters in a normal manner.

Windows keys
The keyboard has two keys that perform Windows-specific functions.

Chapter 1

Keys

Description
Start button. Combinations with this key perform shortcut functions. Below
are a few examples:

Windows logo key

+ (Activates the next Taskbar button)
+ (Opens the My Computer window)
+ (Opens Help and Support)
+ (Opens the Find: All Files dialog box)
+ (Opens the Run dialog box)
+ (Minimizes all windows)

+
Application key

+< M> (Undoes the minimize all windows)

This key has the same effect as clicking the right mouse button; it opens the
application’s context menu.

Hot Keys
The computer employs hot keys or key combinations to access most of the computer’s controls like screen
contrast and brightness, volume output and the BIOS Utility.
To activate hot keys, press and hold the key before pressing the other key in the hot key combination.

Hot Key

Icon

Function

Description

Fn-l

Hotkey help

Displays a list of the hotkeys and their functions.

Fn-m

Acer eSetting

Launches Acer eSetting in the eManager set by the
Acer Empowering key..

TravelMate 4060

Hot Key

Icon

Function

Description

Fn-n

Power Management

Launches Power options.

Fn-o

Sleep

Puts the computer in Sleep mode.

Fn-p

Display toggle

Switches display output between the display screen,
external monitor (if connected) and both the display
screen and external monitor.

Fn-q

Screen blank

Turns the display screen backlight off to save power.
Press any key to return.

Fn-r

Touchpad Toggle

Turns the internal touchpad on and off.

Fn-s

Speaker toggle

Turns the speakers on and off.

Fn-w

Volume up

Increases the sound volume.

Fn-y

Volume down

Decreases the sound volume.

Fn-x

Brightness up

Increases the screen brightness.

Fn-¨z

Brightness down

Decreases the screen brightness.

Special keys
You can locate the Euro symbol at the upper-center (for European keyboard) and/or bottom-right (Chinese
keyboard) of your keyboard. To type:

Chapter 1

The Euro symbol
1.

Open a text editor or word processor.

Either directly press the key at the bottom-right of the keyboard (for Chinese keyboard), or hold
and then press the <5> key at the upper-center of the keyboard.symbol at the upper-center of
the keyboard (for European keyboard, you can use both method).
NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.

The US dollar sign
1.

Open a text editor or word processor.

Either directly press the key at the bottom-right of the keyboard (for Chinese keyboard), or hold
and then press the <4> key at the upper-center of the keyboard.symbol at the upper-center of the
keyboard (for European keyboard, you can use both method).
NOTE: This function varies according to the language settings.

TravelMate 4060

Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor
responds as you move your finger on the surface of the touchpad. The central location on the palmrest
provides optimum comfort and suuport.

Touchpad basics
The following items teach you how to use the touchpad:

* Move your finger across the touchpad (2) to move the cursor.
* Press the left (1) and right (4) buttons located on the edge of the touchpad to do selection and execution
functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the touchapd is
the same as clicking the left button.
* Use the 4-way scroll (3) button to scroll up or down and move left or right a page. This button mimics your
cursor pressing on the right scroll bar of Windows applications.

Function

Left button (1)

Right button (4)

Touchpad (2)

Execute

Click twice quickly.

Tap twice (at the same speed
as double-clicking a mouse
button).

Select

Click once.

Tap once.

Drag

Click and hold,
then use finger to
drag the cursor on
the touchpad.

Tap twice (at the same speed
as double-clicking a mouse
button); hold finger to the
touchpad on the second tap
and drag the cursor.

Access
context menu
Scroll

Center button (3)

Click once.
Click and hold to
move up/down/left/
right.

NOTE: Keep your fingers dry and clean when using the touchpad. Also keep the touchpad dry and clean. The
touchpad is sensitive to finger movement, hence, the lighter the touch, the better the response. Taping
harder will not increase the touchpad’s responsiveness.

Chapter 1

Hardware Specifications and Configurations
System Board Major Chip
Item

Controller

System core logic

®
Intel 915GM+ICH6-M

Memory controller

®
Integrated in Intel 915GM

Audio controller

RealTek ALC260 HD audio interface

PCMCIA controller for socket

TI PCI1510A

Video controller

®
built-in Intel 915GM

Power and Keyboard controller

KBC NS97551

Wireless controller (mini PCI)

Intel (The controller is on the Wireless LAN card. Please look at the
wireless LAN card for controller details).

(Audio amplifer: Maxiam MAX9755)

Processor
Item
CPU type

Specification
Intel® Pentium® M 730/740/750/760/770/780 processor (2MB L2 cache,
1.60/1.73/1.86/2/2.13/2.26 GHz, 533 MHz FSB)
®
®
Intel Pentium M 725 processor (2MB L2 Cache, 1.60 GHz, 400 MHz FSB)
Intel® Celeron® M processor 360/370/380 (1 MB L2 cache, 1.40/1.50/1.60
GHz, 400 MHz FSB)

CPU package

Intel socketable 478 pins Micro-FCPGA

CPU core voltage

Low speed: 0.8V
High speed: 1.5V

CPU I/O voltage

1.2V

BIOS
Item
BIOS vendor

Specification
Pheonix BIOS

BIOS Version
BIOS ROM type

Flash ROM, SST39VF040

BIOS ROM size

512Kbyte

BIOS package

32 Pin PLCC-lead

Supported protocols

ACPI 2.0 (if available, at least 1.0b), SMBIOS 2.3, PCI 2.2, Boot Block,
PXE 2.0, Mobile PC2001, Hard Disk Password, INT 13h Extensions, PCI
Bus Power Management interface Specification, EI Torito-Bootable CDROM Format Specification V1.0, Simple Boot Flag 1.0

Second Level Cache
Item

Specification

Cache controller

Built-in CPU

Cache size

®
®
2MB for Intel Pentium M processor
®
®
1MB for Intel Celeron M processor

1st level cache control

Always Enabled

2nd level cache control

Always Enabled

TravelMate 4060

Second Level Cache
Item

Specification

Cache scheme control

Fixed-in write back

System Memory
Item

Specification

Memory controller

built-in CPU

Onboard memory size

0MB

DIMM socket number

2 Sockets

Supports memory size per socket

256MB(min)/1024MB(max)

Supports maximum memory size

2GB with 2 SODIMM support

Supports DIMM type

DDRII

Supports DIMM Speed

533MHz

Supports DIMM voltage

1.8 V/0.9V

Supports DIMM package

200-pin so-DIMM

Memory module combinations

You can install memory modules in any combinations as long as they
match the above specifications .

Memory Combinations
Slot 1

Slot 2

Total Memory

0MB

256MB

0MB

512MB

0MB

1024MB

256MB

0MB

256MB

512MB

256MB

512MB

768MB

256MB

1024MB

1280MB

512MB

0MB

512MB

256MB

768MB

512MB

1024MB

512MB

1024MB

1536MB

1024MB

0MB

1024MB

256MB

1280MB

1024MB

512MB

1536MB

1024MB

2048MB (2G)

Above table lists some system memory configurations. You may combine DIMMs with various capacities to
form other combinations.
LAN Interface
Item
Chipset

Specification
RealTek 8100CL

Supports LAN protocol

10/100

LAN connector type

RJ45

LAN connector location

Right side

Chapter 1

Modem Interface
Item

Specification

Chipset

CS1037 Internal Agere Scorpio chipset (Scorpio+CSP1037B)

Fax modem data baud rate (bps)

14.4K

Data modem data baud rate (bps)

56K

Supports modem protocol

V.92MDC

Modem connector type

RJ11

Modem connector location

Right side

Wireless Module 802.11b/g (optional device)
Item

Specification

Chipset
Data throughput

11M~54M bps

Protocol

802.11 b+g

Interface

Mini-PCI type II

Floppy Disk Drive Interface
Item

Specification

Vendor & model name

There is no FDD module for this product

Floppy Disk Specifications
Media recognition

2DD (720KB)

2HD (1.2 MB, 3 mode)

2HD (1.44MB)

Sectors/track

Tracks

Data transfer rate
(Kbit/s)

1 MB

1.6 MB

2 MB

Rotational speed (RPM)

300

360

300

Read/write heads

Encoding method

MFM

Power Requirement
Input Voltage (V)

+5V

.
Hard Disk Drive Interface
Item
Vendor & Model
Name

HGST MORAGA
IC25N060ATMR04-0
08K0634

HGST MORAGA
IC25N080ATMR04-0 08K635

TOSHIBA PLUTO
MK1031GAS

Seagate N2 ST9808210A

SEAGATE N2 ST9100822A

Seagate N2 ST960821A

TOSHIBA PLUTO
MK6025GAS

TOSHIBA PLUTO
MK6025GAS
Capacity (MB)

60000

80000

100000

Bytes per sector

512

Logical heads

Logical sectors

16383

Drive Format
Logical cylinders

TravelMate 4060

Hard Disk Drive Interface
Item
Physical read/write
heads

3/3/4

4/3/2

Disks

2/2/4

Spindle speed (RPM)

4200RPM

8MBytes (8192kbytes)

8MBytes

Performance Specifications
Buffer size

8MBytes (8192kbytes)

Interface

ATA-6

ATA/ATAPI-6

Data transfer, rate
(host~buffer, Mbytes/
s)

100 MB/Sec

5 +/- 5%

DC Power Requirements
Voltage tolerance

5 +/- 5%

Combo Drive Interface
Item
Vendor & model name

Specification

Remark

DVD/CDRW TOSHIBA TS-L462A

General Specification
Interface

Enhanced IDE (ATAPI)

Disc Diameter

8cm/12cm

Loading Type

Drawer Type

Drive Mounting

Horizontal/Vertical

Read/Write

Read Speed:
Max. 24X(3,600 KB/sec) for CD-ROM
Max. 24X(3,600 KB/sec) for CD-RW
Write Speed:
Max. 24X(3,600 KB/sec) for CD-R
Max. 10X(1,500 KB/sec) for CD-RW
Max. 24X(3,600 KB/sec) for US-RW

Mounting Orientation

Horizontal/Vertical

CAV 24X
CAV 24X
P-CAV 24X/20X/16X ; CLV 10X/8X/4X
CLV 10X/4X
P-CAV 24X/16X
All angles

Buffer Under Run

2MB

Power consumption

DC +5v/1.2A

Interface

Enhanced IDE(ATAPI) compatible

Media compatibility

CD:
120mm CD-ROM (Read Only)
80mm CD
800/700/650/550MB CD-Recordable (Read & Write)
700/650MB CD-Rewritable (Read & Write)
700/650MB High Speed CD-Rewritable (Read & Write)
DVD:
5/9/10/18 DVD-Single/Dual (PTP, OTP)
3.9/4.7G DVD-R (Read Only)
4.7GDVD+R (Read Only)
DVD±RW (Read only)
80mm DVD

Chapter 1

Combo Drive Interface
Item

Specification

Remark

Format compatibility

CD
CD-DA (Red Book) - Standard Audio CD & CD-TEXT
CD-ROM (Yellow Book Mode1 & 2) - Standard Data
CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session
CD-I /FMV (Green Book, Mode2 Form1 & 2, Ready, Bridge)
CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video
Video-CD (White Book) - MPEG1 Video
DVD
DVD-ROM (Book 1.02),
DVD-Video (Book 1.1)
DVD-R (Book 1.0, 3.9G)
DVD-R (Book 2.0, 4.7G) - General & Authoring
DVD+R (Version 1.0)
DVD±RW
Play DVD-AUDIO except the case that required CPPM
(Content protection for prerecorded Media)
Write Method

Loading mechanism

Load: Manual
Release: (a) Electrical Release
(Release Button)
(b) Release by ATAPI
command
(c) Emergency Release

Power Requirement
Input Voltage

DC +5V+/- 5% (operation)
DC +5V+/- 8% (start up)

DVD-RW Interface
Item
Vendor & model name

Specification
TOSHIBA TS-L532A

Performance Specification
Transfer rate (KB/sec)
(1) Read DVD-ROM
DVD-R
CD-ROM
(2) Write CD-R
CD-RW
HS-RW
US-RW
(3) ATAPI Interface
PIO mode
DMA mode
Ultra DMA mode

MAX 8X CAV (MAX 10800kB/s)
MAX 4X CAV (MAX 5400kB/s)
MAX 24X CAV (MAX 3600kB/s)
4X, 8X (CLV), MAX. 24X(ZCLV)
4X
(CLV)
4X, 8X, 10X (CLV)
8X, 10X(CLV), MAX. 16X (ZCLV)
16.6MB/s: PIO mode4
16.6MB/s: Multi word mode2
33.3MB/s: Ultra DMA mode2

Buffer Memory

2MB

Interface

Enhanced IDE(ATAPI) compatible

Applicable disc format

Read:
copy-protected DVD discs, CD-ROM, CD audio, DVD-ROM and DVD-RAM,
DVD-R/-RW, DVD+R/+RW and CD-R/-RW, DVD-ROM, DVD-R/+R, DVD-R/+R,
DVD-RW/+RW, 4.38GB DVD-RAM, CD-DA discs, CD-ROM discs, CD-R discs,
CD-RW discs
Write:
CD-R, CD-RW, high-speed CD-RW, Ultra-speed CD-RW, DVD-R, DVD-RW,
DVD+R, DVD+RW

TravelMate 4060

DVD-RW Interface
Item

Specification

Loading mechanism

Load: Manual
Release: (a) Electrical Release (Release Button)
(b) Release by ATAPI command
(c) Emergency Release

Power Requirement
Input Voltage

5 V +/- 5 % (Operating)

Audio Interface
Item

Specification

Audio Controller

Realtek ALC260 (Audio amplifier: Maxim MAX9755)

Audio onboard or optional

Built-in

Mono or Stereo

Stereo

Resolution

18 bit stereo full duplex

Compatibility

HD audio Interface; S/PDIF output for PCM or AC-3 content

Sampling rate

1Hz resolution VSR (Variable Sampling Rate)

Internal microphone

Yes

Internal speaker / Quantity

Yes

Supports PnP DMA channel

DMA channel 0
DMA channel 1

Supports PnP IRQ

IRQ10, IRQ11

Video Interface
Item

Specification

Vendor & Model Name

built-in Intel

Video memory size

915GM

up to 128MB for Aspire 3000/5000
up to 64MB for Aspire 3500

Chip voltage

Core / 2.5V, 1.5V,

Supports ZV (Zoomed Video) port

Graph interface

4X AGP (Accelerated Graphic Port) Bus

Maximum resolution LCD

1600X1200 (UXGA)

Maximum resolution CRT

2048X1536@60HZ

Video Resolutions Mode
Monitor Resolution

2D Display Mode
640x480

120

800x600

120

1024x768

120

1152X864

120

1280X1024

120

1600x1200

1920x1080*16:9

1920x1200

1920x1440

Chapter 1

Video Resolutions Mode
Monitor Resolution
2048x1536

Hz
60

Resolution, colors and maximum refersh rate (Hz) in 256, 65K or 16.7M colors.
NOTE: 16:9 aspect ratio monitors are supported on 1920x1080 and 848x480 on Windows(R)XP, Windows(R)
2000 and Windows(R)ME. The complete list of resolutions depends on the driver version and operating
system. NOTE: resolutions are limited by the performance of the attached monitor.
USB Port
Item

Specification

USB Compliancy Level

2.0

OHCI

USB 2.0

Number of USB port

Location

Two on the right side; one on the front side

Serial port function control

Enable/Disable by BIOS Setup

PCMCIA Port
Item

Specification

PCMCIA controller

TI PCI1510A

Supports card type

Type II (No Tpye III)

Number of slots

One type II

Access location

Right side

Supports ZV (Zoomed Video) port

Supports 32 bit CardBus

Yes (IRQ17)

Keyboard
Item

Specification

Keyboard controller

KBC NS97551

Keyboard vendor

Darfon

Total number of keypads

88-/89-key

Windows keys

Yes

Internal & external keyboard work simultaneously

Yes

Battery
Item
Vendor & model name

Specification
SANYO
PANASONIC
PANASONIC (RoHS)
SANYO LI-ION 4UR18650F-2-QC141
SIMPPLO
SONY

Battery Type

Lithium-ION

Pack capacity

4400mAH

Nominal voltage

14.8V

Number of battery cell

TravelMate 4060

Battery
Item

Specification

Package configuration

4S2P for Sanyo and Panasonic

Package voltage

41.8V / 9.6V

4S1P for Sanyo QC141,SIMPPLO and SONY

LCD
Item

Specification

Vendor & model name

AU B154EW01-08

QDI QD15TL02-03

Screen Diagonal (mm)

15.4inch

Active Area (mm)

331.2(H)x207.0(V)

Display resolution (pixels)

WXGA (1280x800)

Pixel Pitch

0.2588(H)x0.2588(H)mm

Pixel Arrangement

RGB vertical stripe

Display Mode

Normally white

Surface Treatment

Not show

glossy, hardness 2H

Typical White Luminance (cd/m2)

180

160

Luminance Uniformity

not show

1.4(max)

Contrast Ratio

400

Response Time (Optical Rise Time/Fall
Time)msec

25(5ms for rise+20 ms for
decay)

Nominal Input Voltage VDD

not show

Typical Power Consumption (watt)

6.5 (max)

4.38 (for lamp)

also called Brightness

Weight

585

Physical Size(mm)

344(W)x222(H)x6.5(D)

Support Color

Native 262K colours

262K colours

40/40
10/30

45/45
15/35

0 to 50
-20 to 60

Viewing Angle (degree)
Horizontal: Right/Left
Vertial: Upper/Lower
Temperature Range( ° C)
Operating
Storage (shipping)

AC Adapter
Item
Vendor & model name

Specification
LITE-ON PA-1650-02QR
LI SHIN SLS0335A19A57LF
DELTA SADP-65KB

Input Requirements
Maximum input AC current

3.42A

Inrush currenct

50A @ 115Vac
100A @ 230Vac

Nominal frequency (Hz)

50-60

Frequency variation range (Hz)

47-63

Input voltage range (Vrms)

90V AC-264V AC

Inrush current

The maximum inrush current will be less than 50A and 100A when the adapter
is connected to 115Vac and 230Vac respectively.

Chapter 1

AC Adapter
Item
Efficiency

Specification
It should provide an efficiency of 83% minimum, when measured at maximum
load under 115Vac.

Output Ratings (CV mode)
DC output voltage

19V

Noise + Ripple

300mVp-pmax (20 MHz bandwidth)

Load

0(min) 3.16A(max)

Output Ratings (CC mode)
DC output voltage

19V +/-1.0V for CV mode

Constant current mode

3.6 +/- 0.3A

Dynamic Output Characteristics
Turn-on delay time

3 sec (@ 115Vac)

Hold up time

5ms (@115Vac, Full load)

Over Voltage Protection (OVP)

24V

Short circuit protection

3.9A max can be protected and output can be shorted without damage

Electrostatic discharge (ESD)

15KV (at air discharge)
8KV (at contact discharge)

Dielectric Withstand Voltage
Primary to secondary

3000Vac

Leakage current

0.25 mA max. (@ 254Vac, 60Hz)

Regulatory Requirements

Safety Requirements:
1.The subject product rated 100-120V 60Hz must be listed under UL 1950 and
certified with SCA Standard C22.2 No.950.
2.The subject product rated 200-240V 50Hz must comply with low voltage
directive 73/23EEC.
EMI Requirements:
1.The subject product rated 100-120V 60Hz must meet the EMI requirements
of FCC part 15, Subpart B for Class B Digital Device and get FCC Certification
before marketing into USA and Canada.
2.The subject product rated 200-240V 50Hz must meet the EMC Directive 89/
336/EEC.
3.The subject product rated 100-120V must meet the VCCI-2 EMI
requirements.

Power Management
ACPI Mode

Power Management

Mech. Off (G3)

All devices in the system are turned off completely.

Soft Off (G2/S5)

OS initiated shutdown. All devices int he sytem are turned off
completely.

Working (G0/S0)

Individual devices such as the CPU and hard disk may be power
managed in this state.

S3 Sleeping State

CPU set power down
VGA suspend
PCMCIA suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode

S4 Sleeping State

Also called Hibernate stats. System saves all system state and
data onto disk prior to power off the whole system.

TravelMate 4060

Environmental Requirements
Item

Specification

Temperature
Operating

+0~+35 °C

Non-operating

-20~+65 °C

Package storage

-20~+65 °C

Humidity
Operating

10% to 90% RH, non-condensing

Non-operating

10% to 90% RH, non-condensing (Unpacked)

Non-operating

10% to 90% RH, non-condensing (Storage package)

Vibration
Operating (unpacked)

Operation vibration: 1.0G ,X,Y,Zaxis, 30 minutes/axis

Non-operating (unpacked)

5~27.1Hz: 0.6G
27.1~50Hz: 0.04mm (peak to peak)
50~500Hz: 2.0G

Non-operating (packed)

5~62.6Hz: 0.51mm (peak to peak)
62.6~500Hz: 4.0G

Mechanical Specification
Item
Dimensions

Specification
364(W) x 279(D) x 33.9/38.9 (H)mm
14.3 3X 10.98x 1.33/1.53 inches

Weight

6.4 Ibs (2.91kg) for 15” XGA LCD model
6.5 lbs (2.94kg) for 15.4” WXGA LCD model

I/O Ports

Three USB 2.0 ports
Ethernet (RJ-45) port
Modem (RJ-11) port
External display (VGA) port
Microphone-in jack
Line-in jack
Headphones/speaker/line-out jack
Type II PC Card slot
DC-in jack for AC adaptor

Drive Bays

One

Indicators

LED indicator for keyboard hot key: Caps Lock, Scroll Lock, NUmber lock
LED indicator for function indicator: System power-on, HDD/ODD, Wireless on/off,
Arcade LED mode, DC-in, Battery/Charging indicator

Switch

Chapter 1

Power

Chapter 2

System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press to enter Setup” message is prompted
on the bottom of screen).
Press m to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.

PhoenixBIOS Setup Utility
Info.

Main

Security

Boot

Exit

Intel (R) Pentium (R) processor 1.73GHz
CPU Type :
1733MHz
CPU Speed :
HDD Model Name:
TOSHIBA MK1031GAS
HDD Serial Number : 751U0320S
HL-DT-ST DVD-RW GWA-4082N
ATAPI Device :
System BIOS Version : 2A02
Alviso 1219
VGA BIOS Version :
1A16
KBC Version :
LXT123456705290116EF00
Serial Number :
Asset Tag Number :
Produce Name

N/A
Aspire 1640

Manufacturer Name:
UUID :

Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

F1 Help

↑↓

Select Item

F5/F6 Change Values

F9 Setup Defaults

Esc Exit

←→

Select Menu

Enter Select 4 Sub-Menu

F10 Save and Exit

Chapter 2

Navigating the BIOS Utility
There are six menu options: Info., Main, System Devices, Security, Boot, and Exit.
Follow these instructions:
T

To choose a menu, use the cursor left/right keys (zx).

To choose a parameter, use the cursor up/down keys ( wy).

To change the value of a parameter, press por q.

A plus sign (+) indicates the item has sub-items. Press e to expand this item.

Press ^ while you are in any of the menu options to go to the Exit menu.

In any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.

NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information vary in models.

Chapter 2

Information
PhoenixBIOS Setup Utility
Main

Info.

Security

Boot

Exit

N/A
Aspire 1640

Manufacturer Name:
UUID :

Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx

F1 Help

↑↓

Select Item

F5/F6 Change Values

F9 Setup Defaults

Esc Exit

←→

Select Menu

Enter Select 4 Sub-Menu

F10 Save and Exit

NOTE: The system information is subject to different models.

Parameter

Description

HDD Model Name

This field shows the model name of HDD installed on primary IDE master.

HDD Serial Number

This field displays the serial number of HDD installed on primary IDE master.

ATAPI Device

This field displays the mofel name of devices installed on secondary IDE master. The hard
disk drive or optical drive model name is automatically detected by the system.

System BIOS Version

This field displays the BIOS version of the system.

VGA BIOS Version

This field displays the VGA BIOS version of this system.

KBC Version

This filed displays the KBC version of this system.

ATAPI Serial Number

This field shows the serial number of devices installed on secondary IDE master.

Serial Number

This field displays the serial number of this unit.

Asset Tag Number

An Asset Tag with 32 bytes will be stored in EEPROM. Default value is set as
“0000000000000000” (in binary code).

Chapter 2

Parameter
UUID Number

Description
This will be visible only when there is an internal LAN device present. UUID means
Universally Unique ID, a method for computing object identifiers (OIDs). It uses the serial
number in the local Ethernet card combined with the date and time to generate a 128 bit
(16bytes) number. For Acer product, this field displays UUID number. A UUID string will be
stored in the secured data area which is an alphanumeric string of maxium 16 bytes in
length.

Chapter 2

Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup
parameters. It allows the user to specify standard IBM PC AT system parameters.

PhoenixBIOS Setup Utility
Information

Main

Security

Boot

Exit

Item Specific Help
System Time:

[05:45:48]

System Date:

[08/30/2005]

System Memory:

640 KB

, , or
selects field.
Shows system base memory size

Extended Memory:

1040 MB

Shows extended memory size

Video Memory

[128MB]

VGA memory size

Quiet Boot:

[Enabled]

Power On Display:
Network Boot

[Both]
[Enabled]

F12 Boot Menu
D2D Recovery

[Disabled]
[Enabled]

F1 Help

↑↓

Select Item

F5/F6 Change Values

F9 Setup Defaults

Esc Exit

←→

Select Menu

Enter Select 4 Sub-Menu

F10 Save and Exit

NOTE: The screen above is for reference only. Actual values may differ.

Chapter 2

The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.

Parameter

Description

Format/Option

System Time

Sets the system time. The hours are displayed
with 24-hour format.

Format: HH:MM:SS
(hour:minute:second) System Time

System Date

Sets the system date.

Format MM/DD/YYYY (month/day/
year)
System Date

System Memory

This field reports the memory size of the system.
Memory size is fixed to 640MB

Extended Memory

This field reports the memory size of the
extended memory in the system.
Extended Memory size=Total memory size-1MB

VGA Memory

Shows the VGA memory size. VGA Memory
size=64/128MB

Quiet Boot

Determines if Customer Logo will be displayed or
not; shows Summary Screen is disabled or
enabled.

Option: Enabled or Disabled

Enabled: Customer Logo is displayed, and
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and
Summary Screen is enabled.
Power on display

Auto: During power process, the system will
detect if any display device is connected on
external video port. If any external display device
is connected, the power on display will be in CRT
(or projector) only mode. Otherwise it will be in
LCD only mode.

Option: Both or Auto

Both: Simultaneously enable both the integrated
LCD screen and the system’s external video port
(for an external CRT or projector).
Network Boot

Enables, disables the system boot from LAN
(remote server).

Option: Enabled or Disabled

F12 Boot Menu

Enables, disables Boot Menu during POST.

Option: Disabled or Enabled

D2D Recovery

Enables, disables D2D Recovery function. The
function allows the user to create a hidden
partition on hard disc drive to store operation
system and restore the system to factory
defaults.

Option: Enabled or Disabled

NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.

Chapter 2

Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.

Information

Main

PhoenixBIOS Setup Utility
Security
Boot

Exit

Item Specific Help
Supervisor Password Is :
User Password Is :
HDD Password Is :
HDD Master ID :

Clear
Clear
Clear
15422442

Set Supervisor Password
Set User Password
Set HDD Password

[Enter]
[Enter]
[Enter]

Password on Boot

[Disabled]

Help

Esc Exit

Chapter 2

↑ ↓
←→

Supervisor Password
controls accesses of the
whole setup utility.
It can be used to
boot up when Password
on boot is enabled.

Select Item

F5/F6 Change Values

F9 Setup Defaults

Select Menu

Enter Select 4 Sub-Menu

F10 Save and Exit

The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.

Parameter

Description

Option

User Password Is

Shows the setting of the user password.

Clear or Set

Supervisor Password Is

Shows the setting of the Supervisor password.
Please note that Supervisor Password controls
access to the entire Setup. The Supervisor
Password can be used to boot up when
Password on boot is set to enabled.

Clear or Set

HDD Password Is

Shows the setting of the HDD password.

Clear or Set

Set User Password

Press Enter to set the user password. When
user password is set, this password protects
the BIOS Setup Utility from unauthorized
access. The user can enter Setup menu only
and does not have right to change the value of
parameters.

Set Supervisor Password

Press Enter to set the supervisor password.
When set, this password protects the BIOS
Setup Utility from unauthorized access. The
user can not either enter the Setup menu nor
change the value of parameters.

Set HDD Password

Press Enter to set the HDD password.

Primary Harddisk Security

This feature is available to user when
Supervisor password is set. Password can be
written on HDD only when Supervisor
password or user password is set and
password on HDD is set to enabled.
Supervisor Password is written to HDD only
when Supervisor password is being set. User
password is written to HDD when both
passwords are set. When both Supervisor and
user password are present, both passwords
can unlock the HDD.

Disabled or Enabled

Password on Boot

Defines whether a password is required or not
while the events defined in this group
happened. The following sub-options are all
requires the Supervisor password for changes
and should be grayed out if the user password
was used to enter setup.

Disabled or Enabled

NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
NOTE: The User Password can chagne the following items in BIOS: System Date, System Time and Power
on Display on Main menu, System Devices menu and Set User Password function on Security menu.
Meanwhile, the Supervisor Password can change ALL settings in BIOS.

Setting a Password
Follow these steps as you set the user or the supervisor password:
1.

Use the w andy keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Supervisor Password box appears:

Chapter 2

Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.

IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.
4.

Press e.
After setting the password, the computer sets the User Password parameter to “Set”.
If desired, you can opt to enable the Password on boot parameter.

When you are done, press u to save the changes and exit the BIOS Setup Utility.

Removing a Password
Follow these steps:
1.

Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:

Type the current password in the Enter Current Password field and press e.

Press e twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.

When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.

Changing a Password
1.

Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:

Type the current password in the Enter Current Password field and press e.

Chapter 2

Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.

Press e. After setting the password, the computer sets the User Password parameter to “Set”.

If desired, you can enable the Password on boot parameter.

When you are done, press u to save the changes and exit the BIOS Setup Utility.

If the verification is OK, the screen will display as following.

The password setting is complete after the user presses u.
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.

If the new password and confirm new password strings do not match, the screen will display the following
message.

Chapter 2

Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.

PhoenixBIOS Setup Utility
Info.

Main

Advanced

Security

Boot

Exit

Item Specific Help
CD-ROM/DVD Drive
+ and - indicate device
categories. Use to
expand/collapses.

Floppy Devices
+Hard Drive
Network Boot

Boot order is top-down using
only the top device in each
category.
Use and to move
highlighted item up and down.

Help

Esc Exit

Chapter 2

↑ ↓
←→

Select Item

F5/F6 Change Values

F9 Setup Defaults

Select Menu

Enter Select 4 Sub-Menu

F10 Save and Exit

Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.

PhoenixBIOS Setup Utility
Info.

Main

Advanced

Security

Exit

Boot

Item Specific Help
Exit Saving Changes
Exit System Setup and save
your changes to CMOS.

Exit Dicarding Changes
Load Setup Defaults
Discard Changes
Save Changes

Help

Esc Exit

↑ ↓
←→

Select Item

F5/F6 Change Values

F9 Setup Defaults

Select Menu

Enter Select 4 Sub-Menu

F10 Save and Exit

The table below describes the parameters in this screen.

Parameter
Exit Saving Changes

Description
Exit System Setup and save your changes to CMOS.

Exit Discarding Changes

Exit utility without saving setup data to CMOS.

Load Setup Default

Load default values for all SETUP item.

Discard Changes

Load previous values from CMOS for all SETUP items.

Save Changes

Save Setup Data to CMOS.

Chapter 2

BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
T

New versions of system programs

New features or options

Restore a BIOS when it becomes corrupted.

Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.

Create Crisis Recovery Diskette
1.

Rename BIOS file of this product to BIOS.wph

Copy BIOS.wph file to crisis folder and overwrite the original BIOS.wph file.

Insert a blank floppy diskette to floppy drive.

Run cs.bat and follow its instructions to create crisis recovery diskette.

Recover BIOS from Crisis Recovery Diskette
1.

Insert the crisis recovery diskette to the floppy drive.

Use AC adaptor power supply.

Press Fn and ESC key together for more than two seconds when you power on the system.

The system will read the files inside the floppy diskette without backlight.

After one to three minutes, the system will automatically reboot. Please do not shut down the system or
remove the power supply.

After step 1 to 5, you sould be able to recover BIOS already. Then you can see the LCD screen with the
backlight is on.

Chapter 2

Chapter 3

Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
T

Wrist grounding strap and conductive mat for preventing electrostatic discharge

Flat-bladed screw driver

Phillips screw driver

Tweezers

Plastic Flat-bladed screw driver

Hexed Screw Driver
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
T

Chapter 3

General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:

Turn off the power to the system and all peripherals.

Unplug the AC adapter and all power and signal cables from the system

NOTE: Aspire 9100 series product uses mylar or tape to fasten the FFC/FPC/connectors/cable, you may
need to tear the tape or mylar before you disconnect different FFC/FPC/connectors.

Chapter 3

Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence
and instructs you on the components that need to be removed during servicing. For example, if you want to
remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in
that order.

Start

Battery

E*2

RAM/Wireless
Cover

HDD Cover

IO Bezel

ODD Module
*2 back side
*4 left/right side

*2
Heatsink
Cover

HDD Module
Wireless LAN
Card

Memory

ODD
Connector
Board

ODD Holder

special screw for thermal*3
Ex1
Thermal
Module

CPU

ODD Drive

E*3
Middle Cover
B*2
Keyboard
*4
(right and left hinges)
LCD Module

B*2
Switch Board
B*5
E*16+B*2
Lower and
Upper Case
Assembly

Lower Case
Assembly

Upper Case
Assembly
Touchpad

E*2
*2 screw nuts
VGA Heatsink

Chapter 3

Main Board

3-in-1 Cover

*4
Speaker Set

B*2
Modem Board

B*2
Touchpad
Bracket

Bluetooth
Module

Touchpad
Board

LCD Module
4 screw pads
M*4
LCD Bezel

*6 hinges
*2 brackets
LCD Inverter
Antenna set

LCD Cover

LCD
Assembly
*4

LCD

LCD Cable

LCD Brackets

Screw List
Item

Description

SCREW F040 9 5.0X5.0 9.5X(IO) R00

SCREW M2.0X0.4P+3FP ZK(NL)

SCREW M2.5 K 5/2 X0.85 4 ZK(NL)

SCREW M2.5X0.45+10K NIL

SCREW M2.5X0.45+8K ZBL

SCREW M2.5X0.45P+3F NI

SCREW M3.0X0.8P+3K NL

Chapter 3

Removing the Battery Pack
1.

Unlock the battery lock.

Slide the battery latch as shown.

Then remove the battery pack.

Chapter 3

Removing the HDD Module/the Memory and the Wireless LAN Card/
the Thermal Module and the CPU/ODD Module and LCD Module
Removing the HDD Module
1.

Remove the two screws holding the HDD cover.

Remove the HDD cover.

Remove the screw fastening the HDD module to the notebook.

Then detach the HDD module from the notebook.

Removing the Memory and the Wireless LAN Card

Remove the two screws that secure the RAM/Wireless cover.

Remove the RAM/Wireless cover.

Pop up the memory then remove it.

Disconnect the auxiliary and the main wireless antennae.

Pop the wireless LAN card then remove it.

Chapter 3

Removing the Thermal Module and CPU
1.

Remove the three screws holding the thermal door

Detach the thermal door.

Disconnect the fan cable from the main board.

Remove the three screws fastening the thermal module.

Disconnect the fan cable.

NOTE: When you remove the screws fastening the thermal module, please follow the number order 3, 2, 1 on
the thermal module. When you need to assemble the thermal module, fasten the screws as the order 1,
2, 3 on the thermal module.
6.

Use a flat-bladed screwdriver to release the CPU lock.

Remove the CPU from the socket carefully.

Chapter 3

Removing the ODD Module
1.

Remove the three screws holding the middle cover.

Detach the middle cover carefully.

Then remove the two screws fastening the keyboard.

Turn over the keyboard as shown.

Disconnect the keyboard cable from the main board then remove the keyboard.

Remove the screw that fastens the ODD module.

7. Turn over the notebook computer then detach the ODD module carefully.
NOTE: When you reattach the ODD, please make sure you attach the ODD module completely to the main
unit. Otherwise, you can not fasten the screw and the screw may damage the main board.
.

Removing the LCD Module
1.

Remove the three screws holding the keyboard cover.

Open the LCD module as the picture shown then detach the keyboard cover from the main unit.

Chapter 3

Remove the two screws that secure the keyboard as shown.

Turn over the keyboard as shown and disconnect the keyboard cable then remove the keyboard.

Pull out the antenna set with a tweezers then take out the antenna set from the main unit.

Disconnect the LCD coaxial cable.

Remove the four screws holding the right and the left hinge. Two on each side.

Then detach the LCD module from the main unit.

Chapter 3

Disassembling the Main Unit
Separate the Main Unit Into the Upper and the Lower Case Assembly
1.

Remove the two screws holding the switch board.

Remove the switch board.

Disconnect the touchpad FFC from the main board.

Disconnect the bluetooth cable.

Remove the five screws that secure the upper case.

Remove the 17 screws on the bottom as shown.

Detach the upper case assembly and place it next to the lower case assembly.

Disconnect the microphone cable then remove the upper case assembly.

Disassembling the Upper Case Assembly

Disconnect the touchpad board to touchpad FFC.

Disconnect the touchpad board to main board FFC.

Then detach the touchpad board to main board FFC from the touchpad board.

Chapter 3

Remove the three screws that secure the touchpad board.

Remove the touchpad board from the upper case.

Disconnect the touchpad board to touchpad FFC.

Remove the touchpad board to touchpad FFC from the uppwer case assembly.

Remove the four screws holding the touchpad bracket.

Detach the touchpad bracket from the upper case assembly.

10. Remove the touchpad from the upper case.
11. Remove the two screws that secure the bluetooth module.
12. Disconnect the bluetooth module then remove it.

Disassembling the Lower Case Assembly
1.

Disconnect the MDC cable from the modem board.

Chapter 3

Detach the MDC cable from the main board.

Remove the two screws holding the modem board then disconnect the modem board from the main
board.

Disconnect the speaker cable from the main board.

Remove the screw that secure the main board.

Remove the two screw nuts as shown.

The you can detach the main board from the upper case.

Remove the ttwo screws that fasten the N/B heatsink.

Remove the N/B heatsink from the main board as shown.

10. Remove the card reader dummy card from the lower case. (For SKU with three-in-one card reader, please
remove three in one cover).
11. Remove the two screws that secure the speaker set on one side.

12. Then remove another two screws holding the speaker set on the other side.
13. Then take out the speaker set from the lower case.

Chapter 3

IMPORTANT:When assembling/disassembling the main board, whenever there is a mylar on the main board
(see the highlighted with red below; the mylar is sami-transparent, film-like stuff ), it should be
transferred “if necessary” to the replacement main board. Because the main board mylar should be
stuck to the main board to prevent the antenna cable and the main board components short circuit.
The short could cause the main board or the antenna cable burned.

Chapter 3

Disassembling the LCD Module
1.

Remove the four screw caps as shown.

Remove the four screws holding the LCD bezel.

Then detach the LCD bezel from the LCD module.

Disconnect the inverter board then remove it.

Remove the three screws holding the right hinge.

Then remove the three screws that secure the left hinge.

Remove one screw that secure the LCD bracket.

Remove another screw holding the LCD bracket on the other side.

Then detach the LCD panel from the LCD cover carefully.

10. Remove the two screws holding the right bracket.
11. Then remove the right bracket.
12. Remove another two screws that tighten the left bracket.

Chapter 3

13. Remove the left bracket as the picture shows.
14. Tear off the tape fastening the LCD cable.
15. Tear off the the LCD cable fastening the LCD cable, then remove it..

Chapter 3

Disassembling the External Modules
Disassembling the HDD Module
1.

Remove the two screws holding the HDD bracket on one side.

Remove another two screws holding the HDD bracket on the other side.

Then take the hard disc drive out from the HDD bracket.

Disassembling the Optical Drive Module

Remove the four screws as the picture shows.

Remove the two screws that secure the optical disc drive and the ODD holder.

Push the ODD holder as shown.

Detach the ODD holder.

Disconnect the ODD connector board then remove it.

Chapter 3

Chapter 4

Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1.

Obtain the failing symptoms in as much detail as possible.

Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.

Use the following table with the verified symptom to determine which page to go to.

Symptoms (Verified)

Go To

Power failure. (The power indicator does not go
on or stay on.)

“Power System Check” on page 60.

POST does not complete. No beep or error
codes are indicated.

“Power-On Self-Test (POST) Error Message” on
page 63
“Undetermined Problems” on page 75

POST detects an error and displayed messages
on screen.

“Error Message List” on page 64

Other symptoms (i.e. LCD display problems or
others).

“Power-On Self-Test (POST) Error Message” on
page 63

Symptoms cannot be re-created (intermittent
problems).

Use the customer-reported symptoms and go to
“Power-On Self-Test (POST) Error Message” on
page 63
“Intermittent Problems” on page 74
“Undetermined Problems” on page 75

Chapter 4

System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is
required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause
damage to the drive or cause the drive to fail.
Do the following to select the test device.
1.

Boot from the diagnostics diskette and start the diagnostics program.

See if FDD Test is passed as the program runs to FDD Test.

Follow the instructions in the message window.

If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.

Reconnect the external diskette drive/DVD-ROM module.

Replace the external diskette drive/CD-ROM module.

Replace the main board.

External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1.

Boot from the diagnostics diskette and start the diagnostics program.

See if CD-ROM Test is passed when the program runs to CD-ROM Test.

Follow the instructions in the message window.

If an error occurs, reconnect the connector on the System board. If the error still remains:
1.

Reconnect the external diskette drive/CD-ROM module.

Replace the external diskette drive/CD-ROM module.

Replace the main board.

Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1.

Reconnect the keyboard cables.

Replace the keyboard.

Replace the main board.

The following auxiliary input devices are supported by this computer:
T

Numeric keypad

External keyboard

If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
59

Chapter 4

Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.

Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.

Go to the diagnostic memory in the test items.

Press F2 in the test items.

4. Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.

Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.

Remove the battery pack.

Connect the power adapter and check that power is supplied.

Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.

If you suspect a power problem, see the appropriate power supply check in the following list:

Chapter 4

“Check the Power Adapter” on page 61

“Check the Battery Pack” on page 62

Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power
adapter cable. See the following figure

Pin 1: +19 to +20.5V
Pin 2: 0V, Ground

If the voltage is not correct, replace the power adapter.

If the voltage is within the range, do the following:
T

Replace the System board.

If the problem is not corrected, see “Undetermined Problems” on page 75.

T
If the voltage is not correct, go to the next step.
NOTE: An audible noise from the power adapter does not always indicate a defect.

If the power-on indicator does not light up, check the power cord of the power adapter for correct
continuity and installation.

If the operational charge does not work, see “Check the Battery Pack” on page 62.

Chapter 4

Check the Battery Pack
To check the battery pack, do the following:
From Software:
1.

Check out the Power Management in control Panel

In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.

Repeat the steps 1 and 2, for both battery and adapter.

This helps you identify first the problem is on recharging or discharging.

From Hardware:
1.

Power off the computer.

Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground).

If the voltage is still less than 7.5 Vdc after recharging, replace the battery.

To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.

Touchpad Check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1.

Reconnect the touchpad cables.

Replace the touchpad.

Replace the system board.

After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.

Chapter 4

Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 75.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.

Chapter 4

Index of Error Messages
Error Code List
Error Codes
006

Error Messages
Equipment Configuration Error
Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
(THe causes will be shown before “Equipment Configuration
Error”)

010

Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)

070

Real Time Clock Error

071

CMOS Battery Bad

072

CMOS Checksum Error

110

System disabled.
Incorrect password is specified.

Battery critical LOW
In this situation BIOS will issue 4 short beeps then shut down
system, no message will show.

Thermal critical High
In this situation BIOS will shut down system, not show message.

Error Message List
Error Messages
Failure Fixed Disk

FRU/Action in Sequence
Reconnect hard disk drive connector.
“Load Default Settings” in BIOS Setup Utility.
Hard disk drive
System board

Stuck Key

see “Keyboard or Auxiliary Input Device Check” on page 59.

Keyboard error

see “Keyboard or Auxiliary Input Device Check” on page 59.

Keyboard Controller Failed

see “Keyboard or Auxiliary Input Device Check” on page 59.

Keyboard locked - Unlock key switch

Unlock external keyboard

Monitor type does not match CMOS - Run Setup

Run “Load Default Settings” in BIOS Setup Utility.

Shadow RAM Failed at offset: nnnn

BIOS ROM
System board

System RAM Failed at offset: nnnn

DIMM
System board

Extended RAM Failed at offset: nnnn

DIMM
System board

System battery is dead - Replace and run Setup

Replace RTC battery and Run BIOS Setup Utility to reconfigure
system time, then reboot system.

System CMOS checksum bad - Default
configuration used

RTC battery

System timer error

RTC battery

Run BIOS Setup Utility to reconfigure system time, then reboot
system.
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board

Chapter 4

Error Message List
Error Messages
Real time clock error

FRU/Action in Sequence
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board

Previous boot incomplete - Default configuration
used

Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board

Memory size found by POST differed from
CMOS

Run “Load Default Settings” in BIOS Setup Utility.
DIMM
System board

Diskette drive A error

Check the drive is defined with the proper diskette type in BIOS
Setup Utility
See “External Diskette Drive Check” on page 59.

Incorrect Drive A type - run SETUP

Check the drive is defined with the proper diskette type in BIOS
Setup Utility

System cache error - Cache disabled

System board

CPU ID:

System board

DMA Test Failed

DIMM
System board

Software NMI Failed

DIMM
System board

Fail-Safe Timer NMI Failed

DIMM
System board

Device Address Conflict

Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board

Allocation Error for device

Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board

Failing Bits: nnnn

DIMM
BIOS ROM
System board

Fixed Disk n

None

Invalid System Configuration Data

BIOS ROM
System board

I/O device IRQ conflict

Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board

Operating system not found

Enter Setup and see if fixed disk and drive A: are properly identified.
Diskette drive
Hard disk drive
System board

Chapter 4

Error Message List
No beep Error Messages
No beep, power-on indicator turns off and LCD is
blank.

FRU/Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
LED board.
System board.

No beep, power-on indicator turns on and LCD is
blank.

Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Reconnect the LCD connector
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board

No beep, power-on indicator turns on and LCD is
blank. But you can see POST on an external
CRT.

Reconnect the LCD connectors.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board

No beep, power-on indicator turns on and a
blinking cursor shown on LCD during POST.
No beep during POST but system runs correctly.

Ensure every connector is connected tightly and correctly.
System board
Speaker
System board

Chapter 4

Phoenix BIOS Beep Codes
Code

Beeps

Verify Real Mode

03h

Disable Non-Maskable Interrupt (NMI)

04h

Get CPU type

06h

Initialize system hardware

08h

Initialize chipset with initial POST values

09h

Set IN POST flag

0Ah

Initialize CPU registers

0Bh

Enable CPU cache

0Ch

Initialize caches to initial POST values

0Eh

Initialize I/O component

0Fh

Initialize the local bus IDE

10h

Initialize Power Management

11h

Load alternate registers with initial POST
values

12h

Restore CPU control word during warm boot

13h

Initialize PCI Bus Mastering devices

14h

Initialize keyboard controller

16h

1-2-2-3

17h

BIOS ROM checksum
Initialize cache before memory autosize

18h

8254 timer initialization

1Ah

8237 DMA controller initialization

1Ch

Reset Programmable Interrupt Controller

20h

1-3-1-1

22h

1-3-1-3

Test DRAM refresh
Test 8742 Keyboard Controller

24h

Set ES segment register to 4 GB

26h

Enable A20 line

28h

Autosize DRAM

29h

Initialize POST Memory Manager

2Ah

Clear 215 KB base RAM

2Ch

1-3-4-1

RAM failure on address line xxxx

2Eh

1-3-4-3

RAM failure on data bits xxxx of low byte of
memory bus

2Fh
30h

Enable cache before system BIOS shadow
1-4-1-1

RAM failure on data bits xxxx of high byte of
memory bus

32h

Test CPU bus-clock frequency

33h

Initialize Phoenix Dispatch Manager

36h

Warm start shut down

38h

Shadow system BIOS ROM

3Ah

Autosize cache

3Ch

Advanced configuration of chipset registers

3Dh

Load alternate registers with CMOS values

42h

Initialize interrupt vectors

45h
46h

POST Routine Description

02h

POST device initialization
2-1-2-3

Check ROM copyright notice

Chapter 4

Code

Beeps

POST Routine Description

48h

Check video configuration against CMOS

49h

Initialize PCI bus and devices

4Ah

Initialize all video adapters in system

4Bh

QuietBoot start (optional)

4Ch

Shadow video BIOS ROM

4Eh

Display BIOS copyright notice

50h

Display CPU type and speed

51h

Initialize EISA board

52h

Test keyboard

54h

Set key click if enabled

58h
59h

2-2-3-1

Test for unexpected interrupts
Initialize POST display service

5Ah

Display prompt “Press F2 to enter SETUP”

5Bh

Disable CPU cache

5Ch

Test RAM between 512 and 640 KB

60h

Test extended memory

62h

Test extended memory address lines

64h

Jump to User Patch1

66h

Configure advanced cache registers

67h

Initialize Multi Processor APIC

68h

Enable external and CPU caches

69h

Setup System Management Mode (SMM) area

6Ah

Display external L2 cache size

6Bh

Load custom defaults (optional)

6Ch

Display shadow-area message

6Eh

Display possible high address for UMB
recovery

70h

Display error messages

72h

Check for configuration errors

76h

Check for keyboard errors

7Ch

Set up hardware interrupt vectors

7Eh

Initialize coprocessor if present

80h

Disable onboard Super I/O ports and IRQs

81h

Late POST device initialization

82h

Detect and install external RS232 ports

83h

Configure non-MCD IDE controllers

84h

Detect and install external parallel ports

85h

Initialize PC-compatible PnP ISA devices

86h

Re-initialize onboard I/O ports

87h

Configure Motherboard Configurable Devices
(optional)

88h

Initialize BIOS Area

89h

Enable Non-Maskable Interrupts (NMIs)

8Ah

Initialize Extended BIOS Data Area

8Bh

Test and initialize PS/2 mouse

8Ch

Initialize floppy controller

Chapter 4

Code

Beeps

8Fh

Determine number of ATA drives (optional)

90h

Initialize hard-disk controllers

91h

Initialize local-bus hard-disk controllers

92h

Jump to UserPatch2

93h

Build MPTABLE for multi-processor boards

95h

Install CD ROM for boot

96h

Clear huge ES segment register

97h

Fixup Multi Processor table

98h

1-2

Search for option ROMs. One long, two short
beeps on checksum failure.

99h

Check for SMART drive (optional)

9Ah

Shadow option ROMs

9Ch

Set up Power Management

9Dh

Initialize security engine (optional)

9Eh

Enable hardware interrupts

9Fh

Determine number of ATA and SCSI drives

A0h

Set time of day

A2h

Check key lock

A4h

Initialize Typematic rate

A8h

Erase F2 prompt

AAh

Scan for F2 key stroke

ACh

Enter SETUP

AEh

Clear Boot flag

B0h

Check for errors

B2h
B4h

POST Routine Description

POST done- prepare to boot operating system
1

One short beep before boot

B5h

Terminate QuietBoot (optional)

B6h

Check password (optional)

B9h

Prepare Boot

BAh

Initialize DMI parameters

BBh

Initialize PnP Option ROMs

BCh

Clear parity checkers

BDh

Display MultiBoot menu

BEh

Clear screen (optional)

BFh

Check virus and backup reminders

C0h

Try to boot with INT 19

C1h

Initialize POST Error Manager (PEM)

C2h

Initialize error logging

C3h

Initialize error display function

C4h

Initialize system error handler

C5h

PnPnd dual CMOS (optional)

C6h

Initialize notebook docking (optional)

C7h

Initialize notebook docking late

C8h

Force check (optional)

C9h

Extended checksum (optional)

D2h

Unknown interrupt

Chapter 4

Code

Beeps

E0h

Initialize the chipset

E1h

Initialize the bridge

E2h

Initialize the CPU

E3h

Initialize the system timer

E4h

Initialize system I/O

E5h

Check force recovery boot

E6h

Checksum BIOS ROM

E7h

Go to BIOS

E8h

Set Huge Segment

E9h

Initialize Multi Processor

EAh

Initialize OEM special code

EBh

Initialize PIC and DMA

ECh

Initialize Memory type

EDh

Initialize Memory size

EEh

Shadow Boot Block

EFh

System memory test

F0h

Initialize interrupt vectors

F1h

Initialize Run Time Clock

F2h

Initialize video

F3h
F4h

Initialize System Management Mode
1

Output one beep before boot

F5h

Boot to Mini DOS

F6h

Clear Huge Segment

F7h

Boot to Full DOS

Chapter 4

Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
LCD backlight doesn't work

Action in Sequence

LCD is too dark

Enter BIOS Utility to execute “Load Setup Default Settings”, then
reboot system.

LCD brightness cannot be adjusted

Reconnect the LCD connectors.

LCD contrast cannot be adjusted

Keyboard (if contrast and brightness function key doesn't work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board

Unreadable LCD screen

Reconnect the LCD connector

Missing pels in characters

LCD inverter ID

Abnormal screen

LCD cable

Wrong color displayed

LCD inverter
LCD
System board

LCD has extra horizontal or vertical lines
displayed.

LCD inverter ID
LCD inverter
LCD cable
LCD
System board

Indicator-Related Symptoms
Symptom / Error
Indicator incorrectly remains off or on, but system
runs correctly

Action in Sequence
Reconnect the inverter board
Inverter board
System board

Power-Related Symptoms
Symptom / Error
Power shuts down during operation

Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Battery pack
Power adapter
Hard drive & battery connection board
System board

The system doesn’t power-on.

Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Battery pack
Power adapter
Hard drive & battery connection board
System board

The system doesn’t power-off.

Power source (battery pack and power adapter). See “Power
System Check” on page 60.
Hold and press the power switch for more than 4 seconds.
System board

Battery can’t be charged

See “Check the Battery Pack” on page 62.
Battery pack
System board

Chapter 4

PCMCIA-Related Symptoms
Symptom / Error
System cannot detect the PC Card (PCMCIA)

Action in Sequence
PCMCIA slot assembly
System board

PCMCIA slot pin is damaged.

PCMCIA slot assembly

Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from
actual size.

Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings, then
reboot system.
DIMM
System board

Speaker-Related Symptoms
Symptom / Error
In Windows, multimedia programs, no sound
comes from the computer.

Action in Sequence
Audio driver
Speaker
System board

Internal speakers make noise or emit no sound.

Speaker
System board

Power Management-Related Symptoms
Symptom / Error
The system will not enter hibernation

Action in Sequence
Keyboard (if control is from the keyboard)
Hard disk drive
System board

The system doesn't enter hibernation mode and
four short beeps every minute.

See “S4 Sleeping State” on page 26.
Press Fn+oand see if the computer enters hibernation mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board

The system doesn’t enter standby mode after
closing the LCD

See “S4 Sleeping State” on page 26.
LCD cover switch
System board

The system doesn't resume from hibernation
mode.

See “S4 Sleeping State” on page 26.
Hard disk connection board
Hard disk drive
System board

The system doesn't resume from standby mode
after opening the LCD.

See “S4 Sleeping State” on page 26.
LCD cover switch
System board

Battery fuel gauge in Windows doesn’t go higher
than 90%.

Remove battery pack and let it cool for 2 hours.
Refresh battery (continue use battery until power off, then charge
battery).
Battery pack
System board

Chapter 4

Power Management-Related Symptoms
Symptom / Error
System hangs intermittently.

Action in Sequence
Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board

Peripheral-Related Symptoms
Symptom / Error

Action in Sequence

System configuration does not match the
installed devices.

Enter BIOS Setup Utility to execute “Load Default Settings”, then
reboot system.

External display does not work correctly.

Press Fn+F5, LCD/CRT/Both display switching

Reconnect hard disk/CD-ROM/diskette drives.
System board
USB does not work correctly

System board

Print problems.

Ensure the “Parallel Port” in the “Onboard Devices Configuration” of
BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board

Serial or parallel port device problems.

Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup
Utility is set to Enabled.
Device driver
Device cable
Device
System board

Keyboard/Touchpad-Related Symptoms
Symptom / Error
Keyboard (one or more keys) does not work.

Action in Sequence
Reconnect the keyboard cable.
Keyboard
System board

Touchpad does not work.

Reconnect touchpad cable.
Touchpad board
System board

Modem-Related Symptoms
Symptom / Error
Internal modem does not work correctly.

Action in Sequence
Modem phone port
modem combo board
System board

NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 75.

Chapter 4

Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.

Run the advanced diagnostic test for the system board in loop mode at least 10 times.

If no error is detected, do not replace any FRU.

If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.

Chapter 4

Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 60):

Power-off the computer.

Visually check them for damage. If any problems are found, replace the FRU.

Remove or disconnect all of the following devices:
T

Non-Acer devices

Printer, mouse, and other external devices

Battery pack

Hard disk drive

DIMM

CD-ROM/Diskette drive Module

PC Cards

Power-on the computer.

Determine if the problem has changed.

If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.

If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
T

System board

LCD assembly

Chapter 4

Chapter 6

FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 4060.
Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available
on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on
the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use
the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer
machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.

Chapter 6

TravelMate 4060 Exploded Diagram

TravelMate 4060 FRU List

Adapter
NS

ADP 19V 3.42A PA-1650-02QR
90~264V LF

AP.06503.010

ADP 19V 3.42A SLS0335A19A57LF
90~264V EU

AP.06506.002

ADP 19V 3.42A SADP-65KB DBHF
90~264V LF

AP.06501.009

Battery

Chapter 6

TravelMate 4060 FRU List

BATTERY SANYO LI-ION 4S2P 4.4A
4UR18650F-2-QC140

BT.T5003.001

BATTERY PANASONIC LI-ION 4S2P
4.4A CGR-B/8B5AE

BT.T5005.001

BATTERY PANASONIC LI-ION 4S2P
4.4A ROHS

BT.00805.003

BATTERY SIMPPLO PACK LI-ION
4S1P 2.0A

BT.00407.001

BATTERY SANYO PACK LI-ION
4S1P 2.0A

BT.00403.004

BATTERY SONY PACK LI-ION 4S1P
1.96A

BT.00404.004

MODEM 56K (MDC)T60M845.02 EU

54.TAKV7.001

BLUETOOTH MODULE W/ANTENNA

54.T48V7.001

W/L 802.11B/G(WM3B2200BGMW2)

KI.CAX01.008

LAUNCH BOARD

55.TAKV7.001

TOUCH PAD BOARD

55.TAKV7.002

FFC CABLE - TP/B TO MB

50.A50V7.001

Board

Cable

Chapter 6

TravelMate 4060 FRU List

MODEM CABLE

50.A510V7.001

POWER CORD US (3 PIN)

27.A03V7.001

POWER CORD PRC (3 PIN)

27.A03V7.003

POWER CORD KOERA ( Pin)

27.T23V7.006

POWER CORD EU (3 PIN)

27.A03V7.002

POWER CORD UK (3 PIN)

27.A03V7.004

POWER CORD ITALIAN (3 PIN)

27.A03V7.005

POWER CORD- SWISS

27.A03V7.007

POWER CORD AU (3 PIN)

27.A03V7.008

POWER CORD DANISH (3 PIN)

27.A03V7.006

POWER CORD AF (3 PIN)

27.T48V7.001

MIDDEL COVER ERGO W/BUTTON LIGHT GREEN SILVER

42.T50V7.101

UPPER CASE W/TOUCHPAD,
BRACKET, MIC,BLUETOOTH CABLE

60.T91V7.001

UPPER CASE W/TOUCHPAD,
BRACKET, MIC W/O BLUETOOTH
CABLE

60.T91V7.002

LOWER CASE W/SPEAKER

60.A51V7.002

DIMM/WIRELESS COVER

42.A50V7.001

HEATSINK COVER W/O DOCKING

42.A50V7.002

Case/Cover/Bracket Assembly

Chapter 6

TravelMate 4060 FRU List

3 IN 1 DUMMY COVER

42.T51V7.003

HDD COVER

42.T63V7.004

HDD BRACKET

33.T50V7.001

WIRELESS LAN ANTENNA

50.T50V7.003

AMD MOBILE SEMPRON 2800+
25WD

KC.S2802.25D

AMD MOBILE SEMPRON 3000+
25WD

KC.S3002.25D

AMD MOBILE TURION 64 ML28

KC.TML02.280

AMD MOBILE TURION 64 ML30

KC.TML02.300

AMD MOBILE TURION 64 ML32

KC.TML02.320

AMD MOBILE TURION 64 ML34

KC.TML02.340

AMD MOBILE TURION 64 ML37

KC.TML02.370

DVD/CDRW COMBO MODULE 24X
PHILIPS SCB5265 LF

6M.A65V7.004

Communication Module

CPU/Processor

Optical Disk Drive Module
NS

Chapter 6

TravelMate 4060 FRU List

DVD/CDRW COMBO DRIVE 24X
PHILIPS SCB5265 GB LF

KO.02403.007

OPTICAL DEVICE HOLDER-FIX

42.T51V7.003

DVD/CDRW BEZEL FOR G BASE

42.A65V7.003

DVD/CDRW COMBO MODULE KME
UJDA-770

6M.TAGV7.002

DVD/CDRW COMBO DRIVE 24X
KME UJDA-770

KO.02406.013

OPTICAL DEVICE HOLDER-FIX

42.T51V7.003

DVD/CDRW BEZEL FOR G BASE

42.A65V7.003

DVD/CDRW COMBO MODULE LITEON SOSC-2483K LF

6M.ATKV7.001

DVD/CDRW COMBO LITE-ON
SOSC-2483K LF GB

KO.02409.011

OPTICAL DEVICE HOLDER-FIX

42.T51V7.003

DVD/CDRW BEZEL FOR G BASE

42.A65V7.003

DVD/CDRW COMBO MODULE HLDS
GCC-4244N LF

6M.ATKV7.002

DVD/CDRW COMBO HLDS GCC4244N GB LF

KO.0240A.004

OPTICAL DEVICE HOLDER-FIX

42.T51V7.003

DVD DUAL BEZEL G BASE

42.A65V7.003

DVD DUAL MODULE PANASONIC
UJ-840BAA2 G BASE

6M.A51V7.003

DVD DUAL DRIVE PANASONIC UJ840BAA2 D. LAYER G BASE

KU.00807.010

OPTICAL DEVICE HOLDER-FIX

42.T51V7.003

DVD DUAL BEZEL G BASE

42.A51V7.005

DVD DUAL MODULE LITE-ON
SOSW-833 DL G BASE

6M.T66V5.003

Chapter 6

TravelMate 4060 FRU List

DVD DUAL DRIVE LIET-ON SOSW833 DL G BASE

KU.00804.012

OPTICAL DEVICE HOLDER-FIX

42.T51V7.003

DVD DUAL BEZEL G BASE

42.A51V7.005

DVD DUAL MODULE PIONEER DVRK15RA F/W:1.05 G BASE

6M.ATKV7.003

DVD DUAL DRIVEPIONEER DVRK15RA D. LAYER F/W:1.05 G BASE

KU.00805.020

OPTICAL DEVICE HOLDER-FIX

42.T51V7.003

DVD DUAL BEZEL G BASE

42.A51V7.005

DVD DUAL MODULE HLDS GWA4082N G BASE

6M.ATKV7.004

DVD DUAL DRIVE HLDS GWA4082N G BASE

KU.0080D.016

OPTICAL DEVICE HOLDER-FIX

42.T51V7.003

DVD DUAL BEZEL G BASE

42.A51V7.005

40G SEAGATE 2.5 IN. 4200RPM
N2.1ST9402113A (ROHS), F/W 3.01

KH.04001.016

40G TOSHIBA 2.5 IN. 4200RPM
PLUTO MK4025GAS (ROHS) F/W
KA100A

KH.04004.005

40G HGST 2.5 IN. 4200RPM
HAKONA-A F/W :A70G

KH.04007.013

40G WD 2.5 IN. 5400RPM ML40
WD400UE-22HCT0 (ROHS)

KH.04008.025

40G SAMSUNG 2.5 IN. 5400RPM
M40MP0402H (ROHS) F/W YQ20004

KH.0400B.003

60G SEAGATE 2.5 IN. 4200RPM
N2.2ST960812A F/W:3.04

KH.06001.003

60G TOSHIBA 2.5 IN. 4200RPM
PLUTO MK6025GAS (ROHS) F/W
KA200

KH.06004.004

60G HGST 2.5 IN. 4200RPM
HAKONE-A F/W :A70G

KH.06007.009

60G WD 2.5 IN. 5400RPM ML40
WD600UE-22HCT0 (ROHS)

KH.06008.002

80G SEAGATE 2.5 IN. 4200RPM
N2.2ST980829A F/W:3.04

KH.08001.013

80G TOSHIBA 2.5 IN. 4200RPM
PLUTO MK8025GAS (ROHS) F/W
KA023

KH.08004.003

HDD/Hard Disk Drive
NS

Chapter 6

TravelMate 4060 FRU List

80G HGST 2.5 IN. 4200RPM
HAKONE-A F/W:A70G

KH.08007.011

80G WD 2.5 IN. 5400RPM ML40
WD800UE-22HCT0 (ROHS)

KH.08008.027

100G TOSHIBA 2.5 IN. 4200RPM
ARES MK1031GAS (ROHS) F/W
AA204A

KH.10004.001

100G HGST 2.5 IN. 4200RPM
HAKONE-A F/W:A70G

KH.10007.002

AS1680/AS1410 KEYBOARD
DARFON US International

KB.A2707.001

AS1680/AS1410 KEYBOARD
DARFON Chinese

KB.A2707.002

AS1680/AS1410 KEYBOARD
DARFON Spanish

KB.A2707.003

AS1680/AS1410 KEYBOARD
DARFON Thai

KB.A2707.004

AS1680/AS1410 KEYBOARD
DARFON Brazilian Protugese

KB.A2707.005

AS1680/AS1410 KEYBOARD
DARFON Korea

KB.A2707.006

AS1680/AS1410 KEYBOARD
DARFON UK

KB.A2707.007

AS1680/AS1410 KEYBOARD
DARFON German

KB.A2707.008

AS1680/AS1410 KEYBOARD
DARFON Italian

KB.A2707.009

AS1680/AS1410 KEYBOARD
DARFON French

KB.A2707.010

AS1680/AS1410 KEYBOARD
DARFON Swiss/G

KB.A2707.011

AS1680/AS1410 KEYBOARD
DARFON Portuguese

KB.A2707.012

AS1680/AS1410 KEYBOARD
DARFON Arabic

KB.A2707.013

AS1680/AS1410 KEYBOARD
DARFON Belgium

KB.A2707.014

AS1680/AS1410 KEYBOARD
DARFON Sweden

KB.A2707.015

AS1680/AS1410 KEYBOARD
DARFON Czech

KB.A2707.016

AS1680/AS1410 KEYBOARD
DARFON Hungaian

KB.A2707.017

AS1680/AS1410 KEYBOARD
DARFON Norway

KB.A2707.018

AS1680/AS1410 KEYBOARD
DARFON Danish

KB.A2707.019

AS1680/AS1410 KEYBOARD
DARFON Turkish

KB.A2707.020

Keyboard
NS

Chapter 6

TravelMate 4060 FRU List

AS1680/AS1410 KEYBOARD
DARFON Canadian French

KB.A2707.021

AS1680/AS1410 KEYBOARD
DARFON Japanese

KB.A2707.022

AS1680/AS1410 KEYBOARD
DARFON Greek

KB.A2707.023

AS1680/AS1410 KEYBOARD
DARFON Hebrew

KB.A2707.024

AS1680/AS1410 KEYBOARD
DARFON Russian

KB.A2707.025

LCD 15.0 IN. MODULE SAMSUNG
LTN150XB-L03-V LF

6M.ATKV7.011

LCD 15.0 IN. XGA SAMSUNG
LTN150XB-L03-V LF

LK.15006.008

LCD INVERTER BOARD

19.TAKV7.001

LCD CABLE - 15 IN. XGA

50.T50V7.004

LCD BRACKET W/HINGE 15 IN. - L

33.T50V7.002

LCD Module

Chapter 6

TravelMate 4060 FRU List

LCD BRACKET W/HINGE 15 IN. - R

33.T50V7.003

LCD PANEL W/LOGO ANTENNA 14/
15 IN.

60.T50V7.102

LCD BEZEL W/RUBBER PAD 15 IN.

60.T50V7.004

LCD 15.0 IN. MODULE CMO N150X3L07 LF

6M.ATKV7.012

LCD 15.0 IN. XGA CMO N150X3-L07
REV C4 LF

LK.1500D.012

LCD INVERTER BOARD

19.TAKV7.001

LCD CABLE - 15 IN. XGA

50.T50V7.004

LCD BRACKET W/HINGE 15 IN. - L

33.T50V7.002

LCD BRACKET W/HINGE 15 IN. - R

33.T50V7.003

LCD PANEL W/LOGO ANTENNA 14/
15 IN.

60.T50V7.102

LCD BEZEL W/RUBBER PAD 15 IN.

60.T50V7.004

LCD 15.0 IN. MODULE LPL
LP150X07-TLA2 LF

6M.ATKV7.013

LCD 15.0 IN. XGA LPL LP150X07TLA2 LF

LK.15008.019

LCD INVERTER BOARD

19.TAKV7.001

LCD CABLE - 15 IN. XGA

50.T50V7.004

LCD BRACKET W/HINGE 15 IN. - L

33.T50V7.002

LCD BRACKET W/HINGE 15 IN. - R

33.T50V7.003

LCD PANEL W/LOGO ANTENNA 14/
15 IN.

60.T50V7.102

LCD BEZEL W/RUBBER PAD 15 IN.

60.T50V7.004

LCD 15.0 IN. MODULE LPL
LP150X07-TLA2 LF

6M.ATKV7.013

Chapter 6

TravelMate 4060 FRU List

Chapter 6

LCD 15.0 IN. XGA LPL LP150X07TLA2 LF

LK.15008.019

LCD INVERTER BOARD

19.TAKV7.001

LCD CABLE - 15 IN. XGA

50.T50V7.004

LCD BRACKET W/HINGE 15 IN. - L

33.T50V7.002

LCD BRACKET W/HINGE 15 IN. - R

33.T50V7.003

LCD PANEL W/LOGO ANTENNA 14/
15 IN.

60.T50V7.102

LCD BEZEL W/RUBBER PAD 15 IN.

60.T50V7.004

LCD MODULE 15.4 IN. WXGA CMO
N154I1-L09

6M.A51V7.013

LCD 15.4 IN. WXGA CMO N154I1L09

LK.1540D.002

LCD INVERTER BOARD

19.TAKV7.001

LCD CABLE - 15.4 IN. XGA

50.T50V7.006

LCD BRACKET W/HINGE 15.4 IN. - L

33.T50V7.004

LCD BRACKET W/HINGE 15.4 IN. - R

33.T50V7.005

LCD PANEL W/LOGO ANTENNA 14/
15 IN.

60.T50V7.102

LCD BEZEL W/RUBBER PAD 15.4 IN.

60.T50V7.006

LCD 15.4 MODULE SAMSUNG
LTN154X3-L01-V104

6M.ATKV7.014

LCD 15.4 WXGA SAMSUNG
LTN154X3-L01-V104

LK.15406.009

LCD INVERTER BOARD

19.TAKV7.001

LCD CABLE - 15.4 IN. WXGA

50.T50V7.006

LCD BRACKET W/HINGE 15.4 IN. - L

33.T50V7.004

LCD BRACKET W/HINGE 15.4 IN. - R

33.T50V7.005

LCD PANEL W/LOGO ANTENNA
15.4 IN.

60.T50V7.103

LCD BEZEL W/RUBBER PAD 15.4 IN.

60.T50V7.006

LCD 15.4 MODULE QDI QD15TL0203 LF NON-GLARE

6M.ATKV7.015

LCD 15.4 WXGA QDI QD15TL02-03
LF NON-GLARE

LK.15409.004

LCD INVERTER BOARD

19.TAKV7.014

LCD CABLE - 15.4 IN. WXGA

50.T50V7.006

LCD BRACKET W/HINGE 15.4 IN. - L

33.T50V7.004

LCD BRACKET W/HINGE 15.4 IN. - R

33.T50V7.005

LCD PANEL W/LOGO ANTENNA
15.4 IN.

60.T50V7.103

LCD BEZEL W/RUBBER PAD 15.4 IN.

60.T50V7.006

LCD 15.4 IN. MODULE AU
B154EW01 V8 LF NON-G

6M.ATKV7.016

TravelMate 4060 FRU List

LCD 15.4 IN. WXGA AU B154EW01
V8 LF NON-G

LK.15405.005

LCD INVERTER BOARD

19.TAKV7.001

LCD CABLE - 15.4 IN. WXGA

50.T50V7.006

LCD BRACKET W/HINGE 15.4 IN. - L

33.T50V7.004

LCD BRACKET W/HINGE 15.4 IN. - R

33.T50V7.005

LCD PANEL W/LOGO ANTENNA
15.4 IN.

60.T50V7.103

LCD BEZEL W/RUBBER PAD 15.4 IN.

60.T50V7.006

LCD 15.0 IN. MODULE SAMSUNG
LTN150XB-L03-V W/O WIRELESS

6M.ATKV7.021

LCD 15.0 IN. XGA SAMSUNG
LTN150XB-L03-V LF

LK.15006.008

LCD INVERTER BOARD

19.TAKV7.001

LCD CABLE - 15 IN. XGA

50.T50V7.004

LCD BRACKET W/HINGE 15 IN. - L

33.T50V7.002

LCD BRACKET W/HINGE 15 IN. - R

33.T50V7.003

LCD PANEL W/LOGO W/O
ANTENNA 14/15 IN.

60.T56V7.102

LCD BEZEL W/RUBBER PAD 15 IN.

60.T50V7.004

LCD 15.0 IN. MODULE CMO N150X3L07 LF W/O WIRELESS

6M.ATKV7.022

LCD 15.0 IN. XGA CMO N150X3-L07
REV C4 LF

LK.1500D.012

LCD INVERTER BOARD

19.TAKV7.001

LCD CABLE - 15 IN. XGA

50.T50V7.004

LCD BRACKET W/HINGE 15 IN. - L

33.T50V7.002

LCD BRACKET W/HINGE 15 IN. - R

33.T50V7.003

LCD PANEL W/LOGO W/O
ANTENNA 14/15 IN.

60.A56V7.102

LCD BEZEL W/RUBBER PAD 15 IN.

60.T50V7.004

LCD 15.0 IN. MODULE LPL
LP150X07-TLA2 LF W/O WIRELESS

6M.ATKV7.023

LCD 15.0 IN. XGA LPL LP150X07TLA2 LF

LK.15008.019

LCD INVERTER BOARD

19.TAKV7.001

LCD CABLE - 15 IN. XGA

50.T50V7.004

LCD BRACKET W/HINGE 15 IN. - L

33.T50V7.002

LCD BRACKET W/HINGE 15 IN. - R

33.T50V7.003

LCD PANEL W/LOGO W/O
ANTENNA 14/15 IN.

60.A56V7.102

LCD BEZEL W/RUBBER PAD 15 IN.

60.T50V7.004

LCD 15.4 MODULE QDI QD15TL0203 LF NON-GLARE W/O WIRELESS

6M.ATKV7.025

Chapter 6

TravelMate 4060 FRU List

LCD 15.4 WXGA QDI QD15TL02-03
LF NON-GLARE

LK.15409.004

LCD INVERTER BOARD

19.TAKV7.001

LCD CABLE - 15.4 IN. WXGA

50.T50V7.006

LCD BRACKET W/HINGE 15.4 IN. - L

33.T50V7.004

LCD BRACKET W/HINGE 15.4 IN. - R

33.T50V7.005

LCD PANEL W/LOGO ANTENNA
15.4 IN.

60.T56V7.103

LCD BEZEL W/RUBBER PAD 15.4 IN.

60.T50V7.006

LCD 15.4 IN. MODULE AU
B154EW01 V8 LF NON-G W/O
WIRELESS

6M.ATKV7.026

LCD 15.4 IN. WXGA AU B154EW01
V8 LF NON-G

LK.15405.005

LCD INVERTER BOARD

19.TAKV7.001

LCD CABLE - 15.4 IN. WXGA

50.T50V7.006

LCD BRACKET W/HINGE 15.4 IN. - L

33.T50V7.004

LCD BRACKET W/HINGE 15.4 IN. - R

33.T50V7.005

LCD PANEL W/LOGO ANTENNA
15.4 IN.

60.T56V7.103

LCD BEZEL W/RUBBER PAD 15.4 IN.

60.T50V7.006

MAINBOARD 915GM UMA W/
PCMCIA W/O CPU MEMORY

LB.TAK02.001

MEMORY DDR333 256MB INFINEON
HYS64D32020HDL-6-C (.11u)

KN.25602.012

MEMORY DDR333 256MB NANYA
NT256D64SH8C0GM-6K

KN.25603.019

MEMORY DDR333 256MB
SAMSUNG M470L3224FT0-CB3

KN.2560B.008

MEMORY DDR333 256MB HYNIX
HYMD232M646D6-J

KN.2560G.001

MEMORY DDR333 512MB INFINEON
HYS64D64020HBDL-6-C (.11u)

KN.51202.025

MEMORY DDR333 512MB
SAMSUNG M470L6524BT0-CB3

KN.5120B.006

MEMORY DDR333 256MB HYNIX
HYMD564M646B6-J

KN.5120G.006

Main Board

Memory

Speaker

Chapter 6

TravelMate 4060 FRU List

N/S

SPEAKER SET

23.T50V7.001

THERMAL MODULE

60.A51V7.005

NAME PLATE - TM4060

1HYXZZZ24H9

Heatsink

Miscellaneous
NS

RUBBER FOOT

1HYXZZZ24D6

LCD SCREW RUBBER PAD

47.T50V7.003

LCD BEZEL RUBBER PAD

47.T50V7.004

SCREW M2.0X3.0-I-NI-NYLOK

86.A03V7.012

SCREW I2.5*3M-BNIH(M2.5L3)

86.T25V7.012

SCREW M2.5*4L-BZN-NYLOK

86.A03V7.006

SCREW M2.0X5-I-NI-NYLOK

86.T23V7.006

SCREW MM25060IL69

86.A08V7.004

SCREW M2.0*5-I(NI)(NYLOK)

86.T23V7.010

SCREW M2.0X2.5-I-NI-NYLOK

86.A03V7.007

SCREW I2*3M-NIHY (M2L3)

86.T25V7.008

SCREW M1.7*3.0-I (BK)

86.T50V7.001

SCREW I3*3.5M-NIH(M3L3.5)

86.A03V7.011

Screw

Chapter 6

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2006:09:18 14:44:08+08:00
Create Date                     : 2006:02:15 15:20:04Z
Page Count                      : 99
Creation Date                   : 2006:02:15 15:20:04Z
Mod Date                        : 2006:09:18 14:44:08+08:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : Administrator
Metadata Date                   : 2006:09:18 14:44:08+08:00
Creator                         : Administrator
Title                           : S.G_TM4060_BOOK.book
Page Mode                       : UseOutlines
Has XFA                         : No

EXIF Metadata provided by EXIF.tools

S.G_TM4060_BOOK Travel Mate 4060 Travelmate

4060 to the manual b06535fc-05c6-4880-a76e-defa7cc26f5f

Navigation menu

Versions of this User Manual:

Views

Navigation