Snocross Manual 10_23_12_as_comments Winter X Games Video Service Raw Thrills

User Manual: winter-x-games-snocross-video-games-service-manual-raw-thrills

Open the PDF directly: View PDF .
Page Count: 43

Download
Open PDF In Browser	View PDF

You can get this game at www.magic-play.eu

OPERATOR’S MANUAL
040-00032-01

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Safety
OPERATION
Before operating game, read this manual. Failure to properly install and operate this game could result in
malfunction or accident. Operate the game in accordance with the manual.

TRANSPORTING
The cabinet is very heavy. Because the monitor is high, the cabinet is also very top‐heavy. Use appropriate care
when moving or transporting cabinet. It contains fragile glass and electronic components. Avoid rough handling.

HANDLING COMPONENTS
Many components are extremely sensitive to handling, environmental and Electrostatic Discharge (ESD) events—
especially the computer. Do not handle it roughly. Before servicing, call your distributor and inquire about the PC
warranty. Use proper ESD procedures when servicing. Protect components from harmful environmental
conditions, such as extreme temperatures, excessive moisture or other damaging effects.

DISCONNECT POWER
Always turn the power off and unplug the unit before servicing or making adjustments unless otherwise instructed.
Installing or repairing components while power is on can damage the components and void the warranty.

GROUNDING
Avoid electrical shock. Do not plug in AC power until you have inspected and properly grounded the unit. Only plug
into a grounded, three‐wire outlet. Do not use a “cheater” plug or cut off the ground pin on the line cord.

ELECTRICAL SHOCKS
There is no isolation transformer in the cabinet. Disconnect AC power before servicing. However, be aware that
lethal voltages can remain in the electronic components even when AC power is disconnected. Use extreme
caution when servicing. Verify that there is a working ground connection. If the unit sustains water damage, cease
using it immediately and unplug AC power.

MONITOR
The monitor contains no user serviceable parts. Do not attempt to service the monitor.

POWER SELECTOR
Before installing game, ensure the voltage on the PC is set properly. There is a 115/230 VAC selector switch that
must be set for the correct voltage for your site. Verify the fluorescent lamp rating. The rating must match the line
voltage at the installation site.

POWER CORD
If the power cord is damaged or lost, replace it with an identical cord as supplied by the manufacturer or an
authorized service agent.

SURGE SUPRESSOR
It is recommended that you plug your game’s power cord into a surge suppressor to help protect from power
surges that may damage sensitive electronic components.
Snocross TM ©2012 Raw Thrills, Inc. All Rights Reserved. X Games: ©2012 ESPN, Inc.. All rights Reserved. X Games, the X Games logo, ESPN and
the ESPN logo are all registered trademarks for ESPN, Inc

Page 2

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Service Manual
CONNECTORS
When servicing machine, ensure all connectors mate properly. If connectors do not slip in easily, do not force
them. Connectors are often keyed and only connect one way. Check for correct orientation.

COMPUTER
The computer contains sensitive components, including a hard drive. Do not handle it roughly. Call your distributor
before servicing its internal components. Ask about warranty information as it relates to the PC.
Do not turn the PC power switch on or off. It should remain permanently in the ON position.
Cycle AC power on or off with the cabinet power switch.
A dongle has been inserted into one of the USB ports. This is required for game play.
Do not remove the dongle except for troubleshooting purposes.

FLUORESCENT LAMP
A dropped fluorescent lamp tube may break and implode. Shattered glass from the implosion can travel long
distances and cause bodily injury. Use proper procedures when handling broken materials, as these items can
contain hazardous material such as mercury or lead.

HAZARD TO EPILEPTICS
A small portion of the population has an epileptic condition that may cause seizures. Affected persons experience
seizure while watching some television pictures or playing certain video games. People who have not had seizures
may still have an undetected epileptic condition. If anyone in your family has experienced epilepsy symptoms
(seizures or loss of awareness), consult your physical before using video games. While children play video games, a
parent should observe. Be alert to the following symptoms: dizziness, altered vision, eye or muscle twitching,
involuntary movements, loss of awareness, disorientation or convulsions. If you or your child experiences these
symptoms, discontinue use immediately and consult your physician.

MANUAL
Keep this manual available and ready for use. If the game fails to function properly, turn off the machine and
unplug the AC line cord. Contact your local distributor. Your warranty, when applicable, lasts 60 days from your
purchase date. You may not reproduce this document or any of its contents without written authorization from
Raw Thrills, Inc. .

SPECIFICATIONS
For reasons such as performance, this product’s specifications may change without notice. Federal patent,
copyright and other intellectual property laws protect the content, devices and design of the game and its
equipment.

Snocross TM ©2012 Raw Thrills, Inc. All Rights Reserved. X Games: ©2012 ESPN, Inc.. All rights Reserved. X Games, the X Games logo, ESPN and
the ESPN logo are all registered trademarks for ESPN, Inc

Page 3

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Product Specifications
Electrical Power
United States, International and Japan
Inrush AC Current: 7 Amps
Operating AC Current: 5 Amps
Voltage: 115 VAC

Temperature
50° F to 104° F
(10° C to 40° C)

Humidity
Must not exceed 95% relative humidity

Dimensions
Height: 81” (2.06 meters)
Width: 39” (.99 meters)
Depth: 55” (1.39 meters)

Carton Weight
405 lbs. (184 kg)

Page 4

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Setup
Unpack Materials
1. Place the shipping crates on a flat, stable surface.
2. Cut the banding straps and remove the cardboard lids.
3. Lift off the large cardboard containers surrounding the front pedestal and monitor assemblies
and remove any shipping cleats.
4. Remove the coin door key from the coin return slot.
5. Open the top coin door.
6. Locate the keys for the back door and the cash box door.
7. Open the cash box door and remove the cash box.
8. Check for shipping damage to the following:
 SnoCross player accessible areas such as the sled, control panel and dash.
 Marquee and monitor
 Cabinet decals
9. Check the AC line cord for visible signs of damage.
Pay particular attention to the plug and line cord insulation.

Check Electrical Settings
1.
2.
3.
4.
5.
6.

Verify the voltage in the nearest AC outlet.
Verify the AC outlet ground connection is present and working.
Open the back door of the monitor assembly.
Near the AC power transformer, verify the voltage selector switch is set to correct AC voltage.
Route the line cord so that the plug is near the AC outlet.
Replace the back door of the monitor assembly.

Game Power Up
1. Plug in line cord to AC outlet.
2. Turn the power switch to ON.
3. Check that no component is excessively hot or emitting foul odors.
If not, turn off AC power and disconnect line cord. Refer to the diagnostic section of this manual.
4. Once software loads, you will be asked to calibrate the controls.
If not, enter the service menu by pressing the TEST button located on the bracket inside the top
coin door.

Page 5

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL
Diagnostics and Adjustments
The Service Button Panel has four buttons, three of which can navigate the menu system.
But it is easiest to navigate with a Start, View & Snoball button

Volume
UP

TEST

SERVICE

Volume
DOWN



Service Panel TEST

enters diagnostic system.



Either Service Panel TEST button or
Start button

selects the highlighted option.

Service Panel VOL DOWN button or
SnoBall button

moves down through menu or setting choices.

Service Panel VOL UP button or
pressing View

moves up through menu or setting choices.



Highlight and select Exit to return to previous screen.

An on‐screen message acknowledges changes or when you exit a selection without making a change.
At the bottom of each screen there is a brief description of the menu option’s function. A complete
description is available here for all menu functions.
Instructions for completing your first calibration start on the next page.

Page 6

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

INITIAL GAME SETUP
GAME CONTROLS CALIBRATION
1. If the calibration screen is not visible, press the TEST button to enter the Diagnostic System.
2. From the Main Menu, use Volume +/‐ to highlight Calibration.
3. Press a Start button to enter calibration.

4.
5.
6.
7.

Follow on‐screen instructions. Re‐try if calibration data is not valid.
Game will proceed to Location and Venue Name entry.
Enter information to be displayed when player scans the QR Code.
Game will enter Attract Mode. All game settings will be default values if no changes are made at
this time.

GAME CONTROLS AND INTERFACE INSPECTION
Other Tests
See the Diagnostic Section for further information.
1.
2.
3.
4.
5.
6.
7.

Enter the Switch Test menu and verify all switches function.
Enter the Screen Test menu and verify that video is acceptable.
Enter the Sound Test menu and verify the audio works and is not distorted.
Enter the Coin Meter Test menu and verify the operation of the coin meter.
Enter the Cabinet Lamps Test menu and verify that all cabinet lights work correctly.
Enter the Watchdog Test menu, which reboots the game.
Upon a successful reboot, you are ready to make adjustments to pricing, volume and other
functions found in the Adjustments, Audits and Diagnostics section.

Page 7

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

8. Adjustments, Audits and Diagnostics
Main Menu

Test Main Menu
Diagnostics
Game Audits
Pricing Adjustments
System Adjustments
Game Adjustments
Utilities
Calibration
Volume
Attract Volume
Exit

Menu Option

Description

Diagnostics

Verify all game functionality. Allows activation of all inputs and
outputs, including linking and watchdog test.

Game Audits

View game earnings and gameplay statistics.

Pricing Adjustments

Setting for coinage unit, denomination and game pricing.

System Adjustments

System related changes such as networking, language, attract volume,
Wheel power, blower and shaker force etc.

Game Adjustments

Game specific adjustments such as difficulty, bonus time, game entry.

Utilities

Clear Credits, Audits and reset player/game statistics. Check system
software errors and download data to USB external storage device.

Page 8

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Calibration

Calibrate controls for maximum player control and game experience.

Volume

Set volume during game only. Attract volume is adjusted
independently.

Attract Volume

Set attract/ standby mode volume only.

Main Menu
Diagnostics
Switch Test
For troubleshooting purposes, this menu gives you visual feedback of all switch functions.

Page 9

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
Diagnostics
Sound Test
For troubleshooting purposes, this menu gives game sound feedback.

Menu Option

Description

Change Music

Change current music.

Change Effect

Change sound current sound effect.

Play 100Hz or 1kHz

Play low and high frequency to stimulate bass or full range speaker
response.

Pan Center, Left,
Right

Isolate sound into separate channel to verify correct speaker function.

Main Menu
Diagnostics
Wheel Test
For troubleshooting purposes, this menu allows the wheel force feedback to be activated in left and
right direction.

Page 10

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
Diagnostics
Monitor Test
For troubleshooting purposes, this menu allows the diagnosis of the display to detect color or linearity
issues.

Main Menu
Diagnostics
Light Test
For troubleshooting purposes, this menu allows the diagnosis of the game’s controlled lighting features.

Page 11

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
Diagnostics
Coin Meter Test
For troubleshooting purposes, this menu allows the activation of coin meter. Press Start or Test to
advance coin meter.
Main Menu
Diagnostics
Watchdog Test
This menu allows the activation of the watchdog/reset system. Press Start or Test to start test. The
game’s watchdog system allows the machine to recover automatically from a crash or a failure to boot.
The watchdog system is always active.
Main Menu
Diagnostics
Link System Test
This allows the operator to view and reset the link status of two or more games connected to a single
network. Linking three or more games requires a network hub and must be purchased separately.

Page 12

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
Diagnostics
Blower Test
Test the blower function at different speeds. This can also be used to determine desired blower
instensity.

Main Menu
Diagnostics
Shaker Test
Test the seat shaker function at different levels. This can also be used to determine desired shaker
intensity for maximum player experience.

Main Menu
Game Audits
General Audits 1
View general game statistics.

Page 13

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
Game Audits
General Audits 2

Main Menu
Game Audits
Courses

Page 14

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
Game Audits
Courses Wins

Main Menu
Game Audits
Placing

Page 15

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
Game Audits
Vehicles

Main Menu
Game Audits
Upgrades

Page 16

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
Game Audits
Music

Main Menu
Game Audits
Stunts

Page 17

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
Pricing Adjustments

Settings, Defaults and Choices
Setting

Default

Freeplay

Money Unit

USD

Coin Value

0.25

Coins per Bill Pulse
Coins Per Credit
Credits To Start
Credits To Continue
Bonus Credits
Credits For Bonus
Max Credits
First Place Free Race
Multiplay Win Free Race

1
4
1
1
0
5
30
Yes
No

Choices

Yes/No
Card Swipes, USD, AUD, CAD, EUR,
GBP,DEM,FRF,JPY,NLG,ITL,CHF,DKK,MXN,RUR,KRW,CNY
0.01, 0.05, 0.10, 0.25, 0.50, 1.00, 2.00, 5.00, 10.00, 20.00, 50.00,
100.00, 500.00, 1000.00, 10000.00
1, 2, 3, 4, 5, 10, 20, 25, 50, 100
1‐10
1‐10
1‐10
Options: 0‐10
1‐20
10, 15, 20, 25, 30, 35, 40, 45, 50
Yes/No
Yes/No

Page 18

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
System Adjustments

Settings, Defaults and Choices
Setting

Motion Seat
Checkpoint Time Bonus
Max Name Length
Wheel Power
Blower Power
Seat Shaker
Automatic Volume Sync
Allow Auto Calibration
Allow Wheel Effects
Network Enabled
Language
QR Codes
Game Venue
Game Location

Default

Choices

Yes
No
7
100
100
60
Yes
Yes
Yes
No
English
On
None
None

Yes, No
Yes, No
3, 4, 5, 6, 7
0‐100
0‐100
0‐100
Yes, No
Yes, No
Yes, No
Yes, No
English, Russian, Chinese, Japanese
On, Off
Enter Venue Name to be displayed.
Enter Location Name to be displayed.

Page 19

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
Game Adjustments

Settings, Defaults and Choices
Setting

Start Time Bonus
Checkpoint Time Bonus
Game Difficulty
Speed Measurements
Plays For Score Reset
Autopilot Available
Girls(Racer/ Crowds)
Name Entry

Default

80
30
5
MPH
10000
Yes
Yes
On

Choices

30‐120
10‐100
1‐10
MPH, KPH
1000‐20000
Yes, No
Yes, No
On, Off

Page 20

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
Utilities

Main Menu
Calibration

Page 21

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Main Menu
Game Volume

Adjust game volume during play mode only. Attract volume is adjusted separately. Automatic Volume
Synch allows for all linked units to be adjusted simultaneously.
Main Menu
Attract Volume

Adjust attract or standby volume only.

Page 22

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

Maintenance
Hard Drive Recovery
Symptoms requiring hard drive recovery include








File Test reports bad or missing files.
Game fails to finish loading during startup.
After resetting the AC power, an error is reported.
You are prompted to insert a boot DVD.
Erratic Game or Attract Mode.
Garbled characters
Bad audit files

To identify corrupt files, press Test, choose System Test Menu and run the CRC Check.
The only way to repair corrupt files is to recover the hard drive, as detailed below.
COMPUTER
The computer contains sensitive components, including a hard drive. Do not handle roughly. Call your distributor
before servicing its internal components. Ask about warranty information as it relates to the PC.

Do not use the PC on/off switch. Turn AC power on or off with the cabinet power switch.
1. With game and PC on, verify that the RIO board has power. If not, see Troubleshooting.
2. Open the Coin door.
3. Open the PC DVD‐ROM tray by reaching back to the PC and pressing the Open/Close button on
the drive bay.
4. Insert the first of two restore DVDs (labeled Disc 1) into the tray.
5. Close the tray by pressing the Open/Close button again.
6. Turn cabinet power switch to OFF. Wait 30 seconds.
7. Turn cabinet power switch to ON.
8. Recovery begins automatically when PC boots up.
9. If recovery does not begin, check to ensure disc is inserted correctly and is not damaged.
10. Initial software loading may take several minutes. Check progress periodically.
Do not interrupt power or reset the game during recovery.
11. When software has been loaded, a message indicates that restore is complete. When instructed
to remove disc, open DVD‐ROM drive tray and remove disc.
12. Turn cabinet power switch off.
13. After 30 seconds, turn cabinet power switch on.
14. Game will reboot and enter calibration mode.
15. Re‐calibrate controls.
Snocross TM ©2012 Raw Thrills, Inc. All Rights Reserved. X Games: ©2012 ESPN, Inc.. All rights Reserved. X Games, the X Games logo, ESPN and
the ESPN logo are all registered trademarks for ESPN, Inc

Page 23

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL
BIOS Settings/Power Management
NOTICE
The PC ships with correct BIOS settings. Making changes to the BIOS different from the description below may
adversely affect game functions.

This BIOS setting lets the PC automatically power up. With the setting enabled, the PC reboots when it
detects AC power. This eliminates the need to manually turn the PC back on after power disruption.
Do not use the PC on/off switch. Turn AC power on or off with the cabinet power switch.
1.
2.
3.
4.
5.

Turn cabinet power switch off.
Open rear of cabinet.
Connect a USB keyboard to the PC.
While holding the F10 key on the keyboard down, turn cabinet power switch on.
When the BIOS menu screen appears, make the following adjustments.
(SETTINGS BELOW ARE SPECIFIC TO HP6005 PC. PLEASE CHECK RAWTHRILLS.COM FOR LATEST
INFORMATION ON BIOS SETTINGS AND OTHER TECHNICAL UPDATES)

STORAGE => Storage Options => SATA Emulation : "Native Mode IDE"
ADVANCED => Power On Options => After Power Loss : "On"
6. Follow instructions on screen to save and exit.
7. PC will reset and load the game.

Page 24

You can get this game at www.magic-play.eu

SNOCROSS MOTION OPERATOR’S MANUAL

MECHANICAL ILLUSTRATIONS
AND
ELECTRICAL SYSTEM DIAGRAM

Page 25

You can get this game at www.magic-play.eu

10
9
8

FW (.25 in)
96075A195
(McMaster-Carr)
LW (.190 in)
FW (.190 in)

7
8
9
10

You can get this game at www.magic-play.eu

Flat Washer, #10 Screw,
Black

Flat Washer, 1/4" Screw,
Black
Alloy STL Pin-in-Torx Button
Socket Cap Screw 10-32
Thread, 1" Length, Black
Split Lock Washer, #10 Screw

SnoMotion Snowmobile
Assembly
SX 42" Marquee Assembly
Alloy STL Pin-in-Torx Button
Socket Cap Screw 1/4"-20
Thread, 1" Length, Black
Split Lock Washer, 1/4" Screw

SnoMotion LCD Cabinet
Assembly
SnoBike T-Base Assembly

QTY.

DESCRIPTION

SnoCross Motion Final Assembly

Not Shown:
(1) 600-00982-01 - Rubber Swivel Guard
(10) TP Torx Button Head Machine Screws (10-32 x 1.25"), Black
(10) Flat Washers, #10 Screw, Black

LW (.25 in)

PART NUMBER
SnoMotion LCD
Cabinet
Assembly
SnoBike T-Base
Assembly
SnoMotion
Snowmobile
Assembly
SX42 Marquee
Assembly
96075A223
(McMaster-Carr)

ITEM
NO.

You can get this game at www.magic-play.eu

You can get this game at www.magic-play.eu
27

11
20

16
15

14
17

SnoMotion LCD Cabinet Assembly
(BOM on next page)

You can get this game at www.magic-play.eu

You can get this game at www.magic-play.eu
SnoMotion LCD Cabinet Assembly BOM
ITEM NO.

DESCRIPTION

QTY.

601-00590-01

PART NUMBER

SX Motion - 42" LCD Cabinet

820-00012-00

Cooling Fan(standard size): 12VDC, 3W, 80CFM

800-00001-00

120mm Wire Fan Guard

91772A206 (McMaster-Carr)

90631A009 (McMaster-Carr)

600-00500-01

92865A542 (McMaster-Carr)

LW (.25 in)

18-8 SS Pan Head Phillips Machine Screw 8-32 Thread, 2-1/4" Length
Znc-Pltd Grade 2 STL Nylon-Insert Hex Locknut 8-32 Thread Size, 11/32" Width, 15/64"
Height
SB2 - Inner Tunnel Support Bracket
Grade 5 Zinc-Plated Steel Hex Head Cap Screw 1/4"-20 Thread, 1" Long, Fully
Threaded
Split Lock Washer, 1/4" Screw, Black

FW (.25 in)

600-00963-01

93548A544 (McMaster-Carr)

90675A029 (McMaster-Carr)

Blower Mounting Assembly

600-00254-01

213974-1

90316A194 (McMaster-Carr)

90675A009 (McMaster-Carr)

2-1-10-00-00-000

90316A197 (McMaster-Carr)

20
21

4
1
16
8

Flat Washer, 1/4" Screw, Black

Mounting Shelf - Blower Assembly
Grade 2 Round Head Square Neck Bolt Zinc-Plated Steel, 1/4"-20 Thread, 1-1/4"
Length, Black
Znc-Pltd Stl Machine Screw Nut W/Tooth Washer 1/4"-20 Thrd Sz, 7/16" Nut Width,
3/16" Nut Height
Blower Mounting Assembly

1
3
7
1

Blind Mate Bracket - Female

Blind Mate Housing (Female): 5mm (.197") Centerline, 600 V, 14 A max. (AMP)

18-8 SS Hex Washer Head Slotted Machine Screw 8-32 Thread, 1/2" Length
Znc-Pltd Stl Machine Screw Nut W/Tooth Washer 8-32 Thread Sz, 11/32" Nut Width,
1/8" Nut Height
Full Range Speaker: 5.25", 8 Ohm

18-8 SS Hex Washer Head Slotted Machine Screw 8-32 Thread, 3/4" Length

600-00961-01

Mounting Bracket - Bottom Dash

600-00957-01

Mounting Channel - Dash

2
2

96075A219 (McMaster-Carr)

Alloy STL Pin-in-Torx Button Socket Cap Screw 1/4"-20 Thread, 3/4" Length

SnoMotion Dash Assembly

SnoMotion LCD Assembly

BB142045UHD (Stafast)

Joint Connector Bolt: 1/4"-20 Thread, 1-3/4" Length, Hex Drive 4 mm, Black

800-00005-01

Mid-Width Coin Door Vault (Happ)

810-00053-01

Test Service Button Assembly

RIO Hardware Assembly

90054A197 (McMaster-Carr)

Znc-Pltd STL Hex Washer Head Sheet Mtl Screw Slotted, NO. 8 Size, 3/4" Length

2-1-02-00-00-021

U-San UP-52 Power Supply: 12V/9A

600-00121-01

Bracket - Power Supply Mounting

HP6005

(or approved equivalent PC)

600-00901-01

Bracket - PC Strap Mounting

601-00580-01

91675A333 (McMaster-Carr)

PC Wood Cleat
Hex Washer Head Screw for Sheet Metal 410 Stainless Steel, NO. 8 Size, 1-1/4"
Length
PC Mounting Nylon Strip: 0.075" Thick, 1" Width, Black (56" Length)
Plastic Buckle for Webbing NO Sew Squeeze-Release for 1" Wide Webbing
(Female)
Plastic Buckle for Webbing NO Sew Squeeze-Release for 1" Wide Webbing (Male)

APS Power Supply (90-AP-188)

Alloy STL Pin-in-Torx Button Socket Cap Screw 6-32 Thread, 1" Length, Black

Flat Washer, #6 Screw, Black

Lock Retainer

87425K76 (McMaster-Carr)

29705T86 (McMaster-Carr) - female

29705T86 (McMaster-Carr) - male

2-1-02-00-00-017

96075A123 (McMaster-Carr)

FW (.138 in)

600-00043-01

150-00001-00

Hex Nut for Standard Lock Assembly

96075A203 (McMaster-Carr)

2
2
2

Standard Door Lock

Hex Nut for 7/8" L Standard Lock

Alloy STL Pin-in-Torx Button Socket Cap Screw 10-32 Thread, 1-1/2" Length, Black

You can get this game at www.magic-play.eu

90316A192

7572K16 (McMaster-Carr)

91831A009

603-00591-01
600-00975-01
800-00038-01

4
5
6

4
4

18-8 Stainless Steel Nylon-Insert Hex Locknut
8-32 Thread Size, 11/32" Width, 15/64" Height

18-8 SS Hex Washer Head Slotted Machine
Screw 8-32 Thread, 3/8" Length
Cable Clamp 3/4", Screw Mount

RIO PCB

QTY.
1

90316A194 (McMasterCarr)

604-00022-01

2
3

600-00719-01

PART NUMBER

DESCRIPTION
RIO - Mounting Plate Chassis

RIO Hardware Assembly

500-00040-01

ITEM NO.
PART NUMBER
1
600-00513-01

ITEM NO.

Blower Mounting Assembly

3 inch hose clamp

SX - Blow Tube
Foam Filter Bag

18-8 SS Hex Washer Head Slotted Machine
Screw 8-32 Thread, 1/2" Length

Johnson Blower

SX - Blower Bracket

DESCRIPTION

1
1

QTY.

You can get this game at www.magic-play.eu

DESCRIPTION
Keypad Mounting Bracket

Keypad (pay phone style)
18-8 SS Flat Head Phillips Machine Screw 440 Thread, 3/8" Length
SX - Keypad Glow
18-8 SS Pan Head Phillips Machine Screw 632 Thread, 3/4" Length

95638A194
600-00717-01
500-00116-01
600-00633-01
600-00570-01
96075A115
(McMaster-Carr)
606-00756-01
606-00757-01

5
6
7
8
9
10
11
12

QTY.
1

600-00912-01

96075A139
(McMaster-Carr)

603-00590-01
SnoMotion
Keypad Assy

PART NUMBER

ITEM NO.

SX - 45CM RGB LED Weatherproof Strip Tape

SnoMotion Keypad Assy

2-1-14-00-00-000
91771A108
(McMaster-Carr)
603-00557-01
91772A151
(McMaster-Carr)

500-00074-01

ITEM NO.
PART NUMBER
1
600-00948-01

SnoMotion Dash Assembly

Control Panel Side Decal

Control Panel Center Decal

Alloy STL Pin-in-Torx Button Socket Cap
Screw 6-32 Thread, 1/2" Length, Black

LED Clip

LED Clip (Short)

SX - 36CM ROB LED "Great Wall" Rope

Tamper-Resistant Screw for Sheet Metal Pinin-Torx, 18-8 SS, Button Head, NO.8 Size, 1/2"
L, Black
SX - Hood Scoop Grille

QTY.

SX - Dash Speaker Grille (2)

Alloy STL Pin-in-Torx Button Socket Cap
Screw 8-32 Thread, 1/2" Length, Black

SnoMotion Keypad Assy

Control Panel Dash Plastic

DESCRIPTION

You can get this game at www.magic-play.eu

600-00073-01
809-00004-01
90631A411
(McMaster-Carr)

3
4
5

Foam Tape

601-00037-01

PART NUMBER

ITEM NO.

SnoMotion LCD Assembly

42" HD Monitor
Znc-Pltd Grade 2 STL Nylon-Insert Hex
Locknut 10-32 Thread Size, 3/8" Width,
15/64" Height

42" LCD Display Glass (Tempered)

Black: 1/4"W x 1/8"T x 2"L

42" LCD Frame Assy

DESCRIPTION

QTY.

You can get this game at www.magic-play.eu

93825A120

600-00020-01
90316A194
(McMaster-Carr)

606-00783-01

600-00984-01
820-00005-00

18
19

603-00019-01
600-01007-01
600-01006-01
96075A139
(McMaster-Carr)

14
15
16

90675A029
(McMaster-Carr)

213283-2

213973-1

92865A712

8
600-00253-01

50-2664-22 (Happ)
LW (.50)

6
7

49-3043-00 (Happ)

92865A540

4
5

LW (.25 in)

Faultless-127-2 12R

ITEM NO.
PART NUMBER
1
608-00157-01

Znc-Pltd Stl Machine Screw Nut W/Tooth
Washer 1/4"-20 Thrd Sz, 7/16" Nut Width,
3/16" Nut Height

SnoBike T-Base Assembly

T-Base Caution Decal (small)

T-Base Plexi
18-8 SS Hex Washer Head Slotted Machine
Screw 8-32 Thread, 1/2" Length

Tread Plate - Platform
Pedestal Seat Lamp

2
2

4
2
4

Class 6 Znc-Pltd Steel Hex Nut W/Tooth
Washer M4 Screw Sz, .7mm Pitch, 7mm
Width, 3.2mm Height

T-Base Corner Guard
SX Motion - T-Base Edge Bracket Long
SX Motion - T-Base Edge Bracket Short
Alloy STL Pin-in-Torx Button Socket Cap
Screw 8-32 Thread, 1/2" Length, Black

1
4

QTY.
1

Pin & Socket Hardware Kit, High Durability
Drawer Connector, M4 Thread (AMP)

DESCRIPTION
SX Motion - T-Base Welded Platform
Faultless Swivel Plate Caster (Series 100) 2.5" Wheel Diameter, 1 1/8" Tread Width,
Plain Bearing
Split Lock Washer, 1/4" Screw
Grade 5 Zinc-Plated Steel Hex Head Cap
Screw 1/4"-20 Thread, 3/4" Long, Fully
Threaded
Leg Leveler #1/2-13 Thread, 4"Long, Fully
Threaded
SX Pivot Assy
Split Lock Washer, 1/2" Screw
Grade 5 Zinc-Plated Steel Hex Head Cap
Screw 1/2"-13 Thread, 1" Long, Fully
Threaded
Blind Mate Bracket - Male
Blind Mate Housing (Male): 5mm (.197")
Centerline, 600 V, 14 A max. (AMP)

You can get this game at www.magic-play.eu

15
2

11
12

SnoMotion Snowmobile Assembly
(BOM on next page)

You can get this game at www.magic-play.eu

You can get this game at www.magic-play.eu
SnoMotion Snowmobile Assembly BOM
ITEM NO.

PART NUMBER

DESCRIPTION

QTY.

Rotomolded Snowmobile
Bike Mounting Bracket - Right
Bike Mounting Bracket - Left

1
1
1

SnoMotion Puck Light Assembly

Front Vacform Bracket

Grade 5 Zinc-Plated Steel Hex Head Cap Screw 5/16"-18 Thread,
1" Long, Fully Threaded

Split Lock Washer, 5/16" Screw
Flat Washer, 5/16" Screw
SnoMotion Handlebar Assembly

18
18
1

1
2
3

603-00602-01
602-00002-00
602-00001-00

SnoMotion Puck Light
Assembly

600-00942-01

92865A583 (McMaster-Carr)

7
8
9

LW (.313 in)
FW (.313 in)
96-1301-00

SnoMotion Fairing Assembly

96075A223 (McMaster-Carr)

Alloy STL Pin-in-Torx Button Socket Cap Screw 1/4"-20 Thread, 1"
Length, Black

12
13

Split Lock Washer, 1/4" Screw
Flat Washer, 1/4" Screw, Black

38
38

LW (.25 in)
FW (.25 in)
SnoMotion Track Light
Assembly

SnoMotion Track Light Assembly

92865A542 (McMaster-Carr)

Grade 5 Zinc-Plated Steel Hex Head Cap Screw 1/4"-20 Thread, 1"
Long, Fully Threaded

SnoMotion Radiator Woofer
Assembly

SnoMotion Radiator Woofer Assembly

SnoMotion Tailglow Assembly

96075A139 (McMaster-Carr)

Alloy STL Pin-in-Torx Button Socket Cap Screw 8-32 Thread, 1/2"
Length, Black

FW (.164)

Flat Washer, #8 Screw, Black

TP-Torx-SMS-8x.50

Tamper-Resistant Screw for Sheet Metal Pin-in-Torx, 18-8 SS, Button
Head, NO.8 Size, 1/2" L, Black

21
22

608-00154-01
Exhaust Tip Assembly

SnoMotion Tailpipe
Exhaust Tip Assembly

2
2

TP-Torx-FH-MS-6-32x.375

18-8 SS Tamper-Resist Flat Head Machine Screw Pin-in-Torx, 6-32
Thread, 3/8" Length, Black

24
25
26
27
28
29
30
31
32
33

603-00587-01
600-00941-01
606-00764-01
606-00765-01
606-00762-01
606-00760-01
603-00588-01
606-00766-01
606-00763-01
606-00761-01

SnoMotion Cover Skirt Plastic - Right
Side Skirt Grille
Shock Decal
Right Mech Decal
Right Accent Decal
Right Frame Decal
SnoMotion Cover Skirt Plastic - Left
Left Mech Decal
Left Accent Decal
Left Frame Decal

1
2
2
1
1
1
1
1
1
1

You can get this game at www.magic-play.eu

Exhaust Tip Assembly

90316A165 (McMasterCarr)
606-00773-01

600-00951-01

3
4

500-00111-01

ITEM NO.
PART NUMBER
1
603-00005-01

Znc-Pltd Grade 2 STL Nylon-Insert Hex
Locknut 8-32 Thread Size, 11/32" Width,
15/64" Height

90631A009 (McMasterCarr)

Zinc-Pltd STL Pan Head Phillips Machine
Screw 8-32 Thread, 5/16" Length

90272A191 (McMasterCarr)

QTY.
1

Blue LED Spotlight PCB

DESCRIPTION
Puck Light Bracket

500-00084-02

2-1-18-00-00-000

4
90316A196 (McMasterCarr)

96075A139 (McMasterCarr)

600-00958-01
601-00592-01

PART NUMBER

1
2

ITEM NO.

ITEM NO.
PART NUMBER
1
600-00939-01

SnoMotion Radiator Woofer Assembly

Tail Cap Decal

18-8 SS Hex Washer Head Slotted Machine
Screw 6-32 Thread, 3/8" Length

Exhaust Cap Bracket

SX - 21CM ROB LED "Great Wall" Rope

DESCRIPTION
Tail Pipe Cap

QTY.
1

1
1

QTY.

SnoMotion Puck Light Assembly

18-8 SS Hex Washer Head Slotted Machine
Screw 8-32 Thread, 5/8" Length

8” Woofer, 4 Ohm, Poly-Mica Cone

Alloy STL Pin-in-Torx Button Socket Cap
Screw 8-32 Thread, 1/2" Length, Black

Radiator - 8" Woofer
8" Woofer Panel - Spacer

DESCRIPTION

You can get this game at www.magic-play.eu

96075A219 (McMasterCarr)

606-00614-01

600-00936-01

Alloy STL Pin-in-Torx Button Socket Cap
Screw 1/4"-20 Thread, 3/4" Length

Track Plate Decal

Track Frame Weldment

Alloy STL Pin-in-Torx Button Socket Cap
Screw 1/4"-20 Thread, 1.75" Length, Black
Split Lock Washer, 1/4" Screw

QTY.

SnoMotion - Tread Light Mount Panel

4-Hole Tread Plastic

SnoMotion Track Light Assembly

LW (.25 in)

601-00595-01

96075A139 (McMasterCarr)

TP-Torx-MS-.25-20x1.75

Alloy STL Pin-in-Torx Button Socket Cap
Screw 8-32 Thread, 1/2" Length, Black

500-00071-01

SX - 24CM Blue LED "Great Wall" Rope

603-00544-01

5-Hole Tread Plastic

603-00543-01

SnoMotion Track Plate

DESCRIPTION

600-00937-01

PART NUMBER

ITEM NO.

You can get this game at www.magic-play.eu

603-00595-01
603-00589-01
96075A139 (McMasterCarr)
FW (.164)
96075A155 (McMasterCarr)
606-00767-01

4
5
6
7
8
9

Tail Light Cover Decal

Alloy STL Pin-in-Torx Button Socket Cap
Screw 8-32 Thread, 1-1/2" Length, Black

Flat Washer, #8 Screw, Black

Alloy STL Pin-in-Torx Button Socket Cap
Screw 8-32 Thread, 1/2" Length, Black

Tailglow Housing Plastic

SnoMotion - Taillight Middle Plate

SnoMotion - Taillight Top/Bottom Plate

15CM RGB LED Weatherproof Strip Tape

SnoMotion - Tail Light Bracket

DESCRIPTION

SnoMotion Tailglow Assembly

603-00594-01

500-00113-01

600-00943-01

PART NUMBER

ITEM NO.

QTY.

You can get this game at www.magic-play.eu

702-00036-00
702-00040-00
702-00039-00
606-00758-01
606-00759-01
606-00772-01
606-00771-01

2
3
4
5
6
7
8

603-00605-01

PART NUMBER

ITEM NO.

You can get this game at www.magic-play.eu

SnoMotion Fairing Assembly

Fairing Left Decal

Fairing Right Decal

Fairing Button Decal

Blue X-Button/Gold sw/6V LED
Small Oval Button/White w "VIEW"/Gold
sw/6V LED
Small Oval Button/Red w "SnoBall"/Gold
sw/6V LED
Fairing Speedo Decal

SnoMotion Fairing

DESCRIPTION

QTY.

You can get this game at www.magic-play.eu

SX 42" Marquee Assembly
(BOM on next page)

You can get this game at www.magic-play.eu

SX 42" Marquee Assembly BOM
ITEM NO.

PART NUMBER

DESCRIPTION

QTY.

601-00601-01

SX - 42" Marquee Back Board

500-00093-01

10CM White LED Strip Tape

500-00115-01

20CM White LED Weatherproof Strip Tape

500-00112-01

30CM White LED Weatherproof Strip Tape

500-00064-01

90316A829 (McMaster-Carr)

600-00950-01

White LED PCB - Black Face
18-8 SS Hex Washer Head Slotted Machine Screw 10-32 Thread,
1/2" Length
SX-42 Marquee Board Bracket

96075A219 (McMaster-Carr)

Alloy STL Pin-in-Torx Button Socket Cap Screw 1/4"-20 Thread, 3/4"
Length

LW (.25 in)

Split Lock Washer, 1/4" Screw

10
11

FW (.25 in)
500-00091-01

Flat Washer, 1/4" Screw, Black
130CM Blue LED Strip Tape

12
1

603-00581-01

SX - Marquee Acrylic "X"

13
14

600-00997-01
606-00744-01

0.75" SLEEVE
SX - Marquee Center PETG

12
1

BH-Socket-MS-10-32x1.75

18-8 SS Button Head Socket Cap Screw 10-32 Thread, 1-3/4"
Length, Black

600-00954-01

2" SLEEVE

17
18

606-00746-01
606-00747-01

SX - Snowmobile Left PETG
SX - Snowmobile Right PETG

1
1

BH-Socket-MS-10-32x2.50

18-8 SS Button Head Socket Cap Screw 10-32 Thread, 2-1/2"
Length, Black

20
21

600-01001-01
606-00745-01

2.50" SLEEVE
SX - Marquee Snocross PETG

6
1

BH-Socket-MS-10-32x3

18-8 SS Button Head Socket Cap Screw 10-32 Thread, 3" Length,
Black

603-00598-01

SX - Marquee Back Cover

96075A187 (McMaster-Carr)

Alloy STL Pin-in-Torx Button Socket Cap Screw 10-32 Thread, 1/2"
Length, Black

96075A191 (McMaster-Carr)

Alloy STL Pin-in-Torx Button Socket Cap Screw 10-32 Thread, 3/4"
Length, Black

You can get this game at www.magic-play.eu

2
1

You can get this game at www.magic-play.eu

For Parts or Service contact your local Distributor or:
Betson Enterprises
303 Paterson Plank Road
Carlstadt, New Jersey

Main Phone: (201) 438-1300
Toll Free Phone: (800) 524-2343
Part Phone: (800) 828-2048
CAUTION:





The specifications of this product are subject to change without notice for reasons such
as performance.
The content of this game, its main devices and design are protected under each federal
law concerning patent, copyright and other intellectual properties.
Unauthorized reproduction of this document or any of its contents is strictly forbidden.
Visit www.Rawthrills.com for the latest technical information.

You can get this game at www.magic-play.eu

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2012:10:23 10:23:00-05:00
Author                          : Richmond
Modify Date                     : 2015:09:28 15:45:16+02:00
Page Count                      : 43
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Title                           : Microsoft Word - snocross manual 10_23_12_as_comments
Creator                         : Richmond
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2013:06:27 16:52:21-05:00
Producer                        : Acrobat Distiller 9.5.2 (Windows)
Document ID                     : uuid:35ef1b51-ffb9-41e9-ae2f-d8d8e58f6e57
Instance ID                     : uuid:6f7121b8-2405-4f9f-8211-b4069981ebef
Has XFA                         : No

EXIF Metadata provided by EXIF.tools

Snocross Manual 10_23_12_as_comments Winter X Games Video Service Raw Thrills

Navigation menu

Versions of this User Manual:

Views

Navigation