Dongbu Robot DRI-0007 ZIGBEE MODULE User Manual

Dongbu Robot Co., Ltd. ZIGBEE MODULE Users Manual

Contents

User Manual

DRI-0007 Zigbee Module User Manual
Block Diagram & Operational description
ZigBee Chipset(RP-S2470) Pin Description
FCC Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected. • Consult the dealer or an experienced radio/TV technician for help. Caution Modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation IMPORTANT NOTE: FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this equipment near water. 6) Do not using near any heat sources such as radiators, heat resisters, stove, or other equipment that produce heat. European CE notice to users and product statements This product is CE marked according to the provisions of the R&TTE Directive(99/5/EC). Hereby, Dongbu Robot Co., Ltd. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. For further information, please contact http:// www. dongbu.com Dongbu Robot Co., Ltd. #235, Singal-ri, Jiksan-eup, Seobuk-gu, Cheonan-si, Chungcheongnam-do, Korea Tel: +82-41-590-1700 / Fax: +82-41-590-1702 URL: www. dongbu.com
CONTACT INFORMATION Manufacturer Address : #235, Singal-ri, Jiksan-eup, Seobuk-gu, Cheonan-si, Chungcheongnam-do, Korea To locate in-country Dongbu Robot Co., Ltd., distributors of the Zigbee Module please refer to the Dongbu Robot Co., Ltd. Website http://www. www. dongbu.com These distributor(s) represent local contacts for this product. CORPORATE HEADQUARTERS: Dongbu Robot Co., Ltd. #235, Singal-ri, Jiksan-eup, Seobuk-gu, Cheonan-si, Chungcheongnam-do, Korea Tel: +82-41-590-1700 Fax: +82-41-590-1702 Web: http:// www. dongbu.com This device complies with Industry Canada license-exempt RSS standard(s). Operation is Subject to the following two condition: (1) this device may not cause interference ,and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
EUROPEAN UNION “DECLARATION OF CONFORMITY” DECLARATION OF CONFORMITY Dongbu Robot Co., Ltd. #235, Singal-ri, Jiksan-eup, Seobuk-gu, Cheonan-si, Chungcheongnam-do, Korea declare under our sole responsibility that the product(s) Zigbee Module – DRI-0007 to which this declaration relate(s) is in conformance with the following standards: EN 301 489-1 V1.9.2:2011 EN 301 489-17 V2.2.1 :2012 EN60950-1:2006 EN 300 328 V1.8.1:2012 following the provisions of the 1999/5/EC Directives.

Navigation menu