Dongguan longxin barcode equipment LM800 2.4G Wireless Barcode Scanner User Manual

Dongguan longxin barcode equipment co.,LTD 2.4G Wireless Barcode Scanner User Manual

User_Manual

1NADAMOO2.4GWireless&USBwiredBarcodeScannerQuickStartGuideRespected customer,thank you for choose our scanner. Please read carefully the following user manual before using your device. Package Include： 1 x Barcode scanner 1 x USB cable 1 x USB Wireless receiver 1 x User manual Technical Parameters Interface： USB Wires + 2.4 G Wireless Transmission diatancce: 30m/98ft Light source:Red LED (Aiming) Storage:30000 barcode Decoding capability: UPC-A,UPC-E,EAN-13,EAN-8,ISBN/ISSN code,code 39,code 39 Full ASCII,code93,code 128, code128 Full ASCII, Codabar, Interleaved 2 of 5,industral 2 of 5,Chinese Postal code,MSI, Code11 Decoding speed:260 scan /s Error rate:1/500million Trigger mode: Manual trigger, Continuous scanning Scanning area: 5*5 cm2 ~ 30-30cm2 Indicator mode：Buzzer indicator light Charging time:4 hours Shock resistance: design to fall from 1.5meters from concrete surface Charging Please ensure that the scanner has enough power before start using it. If the scanner is run out of battery,the buzzer will ring for a second.And the scanner will shut down automatically. At this time,please stop scanning and charge the scanner. Correctly insert one end of USB cable into the scanner, and insert another end to computer USB interface or 5V DC USB interface power (NOTE: please use computer USB interface or special 5V DC power supply to charge, the informal power will cause permanent damage to scanning gun and battery), Yellow LED light will light when is at charge state, the charging will complete after about four hours and the yellow LED light will go out.
Power onPress the butto Power offThe system dea long beeping **Scan one of time interval y30s auto powe 5min auto pow20min auto po Reset theTo reset the fa ConnectioWired Mode: 1. Connect the2. Press the sc3. Scan the fol 4.Run Microsofbarcode into th on,the scanner will f efault shut down timeg. And the system w the following barcodyou set,the scanner er off (default) wer off ower off e factory defaactory default seting reset ton Setting e scanner to your cocanner's yellow buttllowing code to conv PS2 keyboardft Word on computehe location of the cu2beep two times. Powe is 30s. If non-operwill shut down automde to set the time inwill power off. 6 1 ult setting ,scan the following the factory defalut omputer Via USB cabon to wake up the svert the scanner to d wired mode er,when barcode is sursor. wer is on successfulration in 30s, the scamatically. nterval,when it's idle60s auto power off 0min power off power offf code ble scanner. wired mode scaned, the scanner ly. anner will issue e exceeding the inputs the
Wireless Mod1.Plug the USB2.Press the sca3.Scan the follscanner to wir Wireless mode4.Run Microsofbarcode into th Under wireless A.Real-time ubarcode is uplobuzzer will givdiscontinuous. **To set the sc Real B.Collection mit’s own memodata to compu **To set the sc Collection mod** Scan the fo de: B wireless receiver ianner's yellow buttoowing codes to mateless mode e ft Word on computehe location of the cus mode,there are twupload mode: Scanoad successfully, thee one continuous so canner to Real-time-time upload mode mode：Under this mory. Internal storage uter when you need canner to Collectionde ollowing barcode to Upload data 3nto a PC’s USB porton to wake up the sctch the receiver withMatch the er,when barcode is sursor. wo 2 upload mode： nning barcode and re blue LED light willounds;if the scan faie upload mode,pleas mode, the scanner w supports up to 30,0 it. n mode ,please scanupload the stored dt canner. h the scanner and corscaned, the scanner eal-time upload the flicker once, at theiled,the buzzer beepse scan the followingwill automatically sto000barcodes .You co the following barcoata onvert the receiver inputs the barcode.If the same time p twice g barcode ore the data in ould upload the ode
 **Scan the fol Show**Scan the fol Cle Scanning Key trigger mContinuous sThe scanner re ** Scan one o K Co Buzzer seScan one of th Open vo Upload spScan one of thlowing barcode to sw total storage lowing barcode to cear data Mode Settingmode: Red laser lighscanning mode: Reeads barcode withouf the following barcoKeys Trigger mode (dontinuous Mode ettings： he following barcode ice peed he following barcode 4show total number oclear all the stored bg ht is on when pressed laser light always ut pressing any buttode to select scannidefault) e to ON / OFF the bu Close voice to select the dataof stored barcode barcode sing the button on when the scannetons. ing mode uzzer ce a upload speed er is electrified.
 Upload speedData Edtt ID settings Add Code ID a Case sensit All in lower-caAll in capital leChage lower-cChange capita Turn off letter -fast Uploaing s as prefix Add Ctivity settings se letters etters ase to capital l to lower-case conversion 5ad speed-modest (dCode ID as suffix default) Upload Turn off ID (d speed-slow (default)
 Barcode se code39-On code39 UPCA-ON UPCA to EAN 13UPCE-On UPCE tO UPCA-OEAN13-On etting Code39-Offcode39 FulASCII-Off UPCA-Off 3-On UPCA TO EAUPCE-Off On UPCE to UPEAN13-Off 6f Code39ll Code39UPCA-cAN13-Off UPCA IUPCE-cPCA - Off UPCE IEAN13- check digit-ON ID Character “m” check digit - ON D Character “e” check digit - ON D character “f” check digit -OnCode39 check digit-Off UPCA-check digit-Off UPCE-check digit - off EAN13-check digit-Off
EAN13 to IBSNEAN8 -On EAN8-2digit extracode-On Code93-On Code128-On Codabar-On Interleaved 2 5-On N- On EAN13 to IEAN8-Off EAN8-5 digextracode-Code93-OffCode128-OfCodabar-Ofof Interleave5-Off 7IBSN- Off EAN13 EAN8-cgit -On EAN8-f Code93ff Code12ff Codabaed 2 of InterlcharacID charater “d” check digit- On extracode-Off id charater “i”8 ID Character “a”ar ID Charater “v”eaved 2 of 5 ID cter “n”  EAN8-chec digit-Off EAN8 ID character “c”
Industrial 2 -On Prefix & su Insert charat (1) . The first sEnter into pref (2) .The seconE.g. To add pre 1082 R Now the “RST” Scan the abov of 5 Industrial5-Off MSI-Offuffix setting ter as prefix step: scan the set u fix setting nd step: scan the neefix ”RST”,scan the ” will be added then X001E52257 e X001E52257 barc8l 2 of IndustCharacMSI IDCode11up code below： eeded character codcharacter R , S ,T in 1083 S scan the normal bacode, ”RSTX001E522rial 2 of 5 ID cter “o” D character “s” ID Character “u”e （char-table is onn order. 1ar code 257” will show.  n page 10） 084 T
Insert charat (1) . The first s Enter into (2) .The seconE.g. To add pre 1082 R Now the “RST”X001E52257 Scan the abov Example: To add TAB a To add CR afte To add CR&LF Scan the follow Clear all charaprefix ter as suffix step: scan the set u suffix setting nd step: scan the neefix ”RST”,scan the ” will be added thene X001E52257 barcafter barcode , Pleaser barcode , Please sF after barcode , Plewing to clear charac cter suffix 9up code below： eeded character codcharacter R , S ,T in 1083 S scan the normal ba code, ”X001E52257se scan the “enter inscan the “enter intoase scan the “enter cter e （char-table is onn order. 10ar code 7RST” will show.nto suffix setting”“To suffix setting”“CR ” into suffix setting”“Clear alln page 10） 084 T TAB” ” “CR ””LF” character
 char-ta 1001S 1004E 1007B 1010 LF 1013 1016D 1019Dable SOH 100EOT BEL CR DLE DC3 1002STX 1005ENQ 1008Backspace1011VT 1014SO 1017DC1 1020DC4 10 10 10 1 1 1 0 10003ETX 006ACK 009TAB 012FF 015SI 18DC2 021NAK
 1022S 1025 1028 1031US 1034“ 1037 1040 1043SYN 5EM 8FS 1037% 0( 3+ 111023ETB 1026SUB 1029GS 32SPACE 1035# 1038& 1041) 1044, 10 10 1 1 1 1 1 1024CAN 027ESC 030RS 1033! 1036$ 1039‘ 1042* 1045-
 1046 1049 1052 1055 1058 1061 1064 10676. 91 24 57 8: 1= 4@ 7C 121047/ 10502 10535 10568 1059; 1062> 1065A 1068D 1 1 1 1 1 1 1 110480 10513 10546 10579 1060< 1063? 1066B 1069E
 1070 1073 1076 1079 1082 1085 1088 10910F 3I 6L 9O 2R 5U 8X 1[ 131071G 1074J 1077M 1080P 1083S 1086V 1089Y 1092\ 1 1 1 1 1 1 1 11072H 1075K 1078N 1081Q 1084T 1087W 1090Z 1093]
 1094 1097 1100 1103 1106 1109 1112 11154^ 7a 0d3g 6j 9m 2p 5s 141095_ 1098b 1101e 1104h 1107k 1110n 1113q 1116t 1 1 1 1 1 1 1 11096` 1099c 1102f 1105i 1108l 1111o 1114r 1117u
 1118 1121 1124 1127De 1130 1133 1136 1139F8v 1y 4| elete 0F3 3F6 6F9 F12 151119w 1122z 1125} 1128F1 1131F4 1134F7 1137F10 1140INSERT 1 1 1 1 1 1 11 111120x 1123{ 1126~ 129F2 132F5 135F8 138F11 41HOME
 1142Pag 1145Page 1148Down For any spe natamo@12 ge up e down n arrow cific requests, pl26.com , burnfree161143Delete 1146Right arrow1149Up arrowease contact us:e@126.com 11 1147L: 144END Left arrow
17FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver.
18-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. * RF warning for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portableexposure condition without restriction.

Navigation menu