Doodle Labs NM-DB-3 Wi-Fi Radio Transceiver User Manual

Doodle Labs (SG) Pte Ltd Wi-Fi Radio Transceiver

User Manual

NM-DB-3Rugged/Military grade 2.4/5 GHz 3x3 MIMO Wi-Fi® Radio TransceiversFeaturesQualcomm-Atheros AR9590-AR1B Chipset with Extended Temperature RangeUp to 450 Mbps Throughput with 3x3 MIMO TechnologyCalibrated High Power 2.4 GHz and 5 GHz operation for Extended Range802.11 Dynamic Frequency Selection (DFS) in AP and Client mode Supported Ath9k Linux DriverMiniPCIE InterfaceUser Manual
TECHNICAL SPECIFICATIONSModel No. NM-DB-3MAC ChipsetQualcomm AtherosQCA9590-AR1B with Extended Temperature range for Outdoor and Rugged models)Software Support Linux Driversath9kCenter Frequency Range5.180 GHz ~ 5.825 GHz2.412 GHz ~ 2.462 GHzThis varies by the regulatory domainChannel Bandwidth* 20, 40 MHz channelsRadio Modulation (Dynamic Link Adaptation)BPSK, QPSK, 16 QAM, and 64 QAM (5.x GHz)CCK, BPSK, QPSK, 16 QAM, and 64 QAM (2.4 GHz)Data Rates Supported802.11a: 6, 9, 12, 18, 24, 36, 48 and 54 Mbps (5.x GHz)802.11n: MCS0-23 (5.x and 2.4 GHz)802.11b/g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48 and 54 Mbps (2.4 GHz)802.11n version 2.0 Capabilities802.11 dynamic frequency selection (DFS) as an AP and Client802.11n and b/g Beam FormingPacket aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx), Maximal ratio combining (MRC), Cyclic shift diversity (CSD), Frame aggregation, block ACK, 802.11e compatible bursting, Spatial multiplexing, cyclic-delay diversity (CDD), low-density parity check (LDPC), Space Time Block Code (STBC)Phy data rates up to 450 Mbps (40 MHz channel)Operating Modes AP, STA and Adhoc modes to implement Point to Point, Point to multi PointMAC Protocol TDD with Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA)Wireless Error Correction FEC, ARQWireless Data Security 128 bit AES, WEP, TKIP and WAPI hardware encryption. Support for IEEE 802.11d, e, h, i, k, r, v, w and time stamp standardsFIPS Certification Loop back mode to facilitate FIPS AES certification, Small packet size (96 bytes) in AES encryption at full packet rateTx/Rx SpecificationRadioModulation Coding Rate Max Tx Power Rx Sensitivity(Typ)5 GHz (20 MHz Channel)802.11a, STBC BPSK 1/2 25.18 -96802.11n, STBC 64 QAM 3/4 25.09 -81MIMO BPSK 1/2 25.09 -93MIMO 16 QAM 3/4 25.09 -83MIMO 64 QAM 5/6 25.09 -725 GHz (40 MHz Channel)MIMO BPSK 1/2 22.93 -90MIMO 16 QAM 3/4 22.93 -79MIMO 64 QAM 5/6 22.93 -69 2.4 GHz (20 MHz Channel)802.11b, STBC 1 Mbps CCK 27.32 -100802.11g, STBC 64 QAM 3/4 27.16 -80802.11n, MIMO BPSK 1/2 26.84 -92
802.11n, MIMO 16 QAM 3/4 26.84 -82802.11n, MIMO 64 QAM 5/6 26.84 -722.4 GHz (40 MHz Channel)802.11n, MIMO BPSK 1/2 26.94 -90802.11n, MIMO 16 QAM 3/4 26.94 -79802.11n, MIMO 64 QAM 5/6 26.94 -70Note 1 It is advantageous to use the smallest Channel Bandwidth that can support the Throughput requirements. Smaller bandwidths provide more channels to choose and help avoid interference issues. The system’s SNR is higher at smaller Channel Bandwidths and Range is longer.Note 2 Max allowed Tx power depends on the regulatory domainAntenna Signal Strength -35 to -85 dBm (Recommended), Absolute Maximum=+12 dBmAntenna port isolation for concurrent operationUp to +10 dBm signal strength for 5 GHz signal without degrading 2.4 GHz operationUp to +5 dBm signal strength for 2.4 GHz signal without degrading 5.x GHz operationIntegrated Antenna Port Protection >20 KV (Human Body Model)Receiver LNA Gain >10 dBReceiver Adjacent Channel Rejection (ACR) >18 dB @ 11a, 6 Mbps (Typ)Receiver Alternate Channel Rejection (ALCR) >35 dB @ 11a, 6 Mbps (Typ)Receive chain Noise Figure +6 dBTransmitter Adjacent ChannelLeakage power Ratio (ACLR) 45 dB (Fc ± ChBW)Transmitter Spurious Emission Suppression -40 dBcRF Power control In 0.5 dBm steps. Accuracy of power calibration loop ±2 dBm. Each transceiver individually calibrated and tested.RF Hardware Disable (RF Kill) Pin 20 of miniPCI-E interface. (Required for FAA compliance)Control for External Power Amp Available as an optional configurationSpectral Analysis 8 bit resolution spectral FFTs available for software analysisPHYSICAL, ENVIRONMENTAL AND OTHER SPECIFICATIONSAntenna Ports 3 Ports (50 Ohms) with MMCX connectors.Host Interface miniPCI-Express 1.2 StandardHost CPU Board Any CPU board with Industry standard miniPCI-Express interface with minimum 6 mm connector heightOperating Voltage 3.3 Volts from miniPCI-Express connectorPower Consumption5.3W @ Max power, in continuous data transfer mode on all chains3.75W @ 25 dBm power, in continuous data transfer mode on all chains2.5W @ 20 dBm power (ETSI max), in continuous data transfer mode on all chains0.9W in continuous data receive mode250 mW in Sleep modeShield case temperature range (Operating)-40°C to +80°CThe System’s thermal design should ensure that the transceiver’s casetemperature is maintained within these specifications.Humidity (Operating) 0% – 95% (Non-condensing)
Dimensions 30 x 50 x 7 mm, 14 gramsMechanical drawing and 3D-CAD files available upon requestRegulatory RequirementsDesigned and Verified to meet various regulatory requirements. Formaltesting and approval is required based on the Integrator’s particular host platform and antenna type. The Integrator is also responsible for obtaining all required regulatory approvals in target markets for the finished product.FCC ID 2AG87NM-DB-3CE/ETSI Q3 2016Industry Canada (IC) Q3 2016RoHS/WEEE Compliance Yes. 100% Recyclable/Biodegradable packaging
et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptibleLe présent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio exempts de licence.The term "IC: " before the certification/registration number only signifies that the Industry Canada technical specifications were met. (1) This device may not cause interference; and FCC StatementChanges or modifications not expressly approved by the party responsible for compliance could void the user's authority tooperate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Thisequipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:-- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for helpThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operationSingapore: USA:Doodle Labs (SG) Pte. Ltd. Doodle Labs LLC150 Kampong Ampat 2 Mattawang DriveKA Center, Suite 05-03 Somerset, NJ 08873Singapore 368324 Tel: +1 862 345 6781Tel: +65 6253 0100 Fax: +65 6353 5564This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (2) This device must accept any interference, including interference that may cause undesired operation of the device. This product meets the applicable Industry Canada technical specifications.L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,d'en compromettre le fonctionnementIC Statement The antenna(s) used for this transmitter must be installed to provide aseparation distance of at least 20 cm from all persons and must not becollocated or operating in conjunction with any other antenna or transmitter,except in accordance with FCC multi-transmitter product procedures.Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for anuncontrolled environment.This transmitter must not be co-located or operating in conjunction with any otherantenna or transmitter.The availability of some specific channels and/or operational frequency bandsare country dependent and are firmware programmed at the factory to matchthe intended destination.The firmware setting is not accessible by the end user.The final end product must be labelled in a visible area with the following:“Contains Transmitter Module 2AG87NM-DB-3”In the event that these conditions can not be met (for example certain laptop configurationsor co-location with another transmitter), then the FCC authorization is no longer consideredvalid and the FCC ID can not be used on the final product. In these circumstances, the OEMintegrator will be responsible for re-evaluating the end product (including the transmitter) andobtaining a separate FCC authorization

Navigation menu