Dorel Juvenile Group 08038TX Home Connection Monitor System User Manual 08038 inst E 112103

Dorel Juvenile Group Home Connection Monitor System 08038 inst E 112103

User Manual

User GuideQuestions? Comments? Missing Parts? Contact Us:www.safety1st.com(800) 544-1108©2003 Dorel Juvenile Group Made in CHINAwww.safety1st.com (800) 544-1108 Styles and colors may vary. Distributed by Dorel Juvenile Group, Inc.,2525 State Street, Columbus, IN 47201-7494 In Canada: 12345 Albert-Hudon, Suite 100,Montreal-N, QC Canada H1G 3K9 12/03Home ConnectionMonitor System0803808038_inst_E_112103 12/10/03 2:00 PM Page 1
PLEASE READ THE FOLLOWING WARNINGS AND ALL ASSEMBLYINSTRUCTIONS CAREFULLY BEFORE USING THE SO CLOSE CRIBMONITOR. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.TERMS USED IN WARNINGS: The term “Receiver” corresponds to “Parent’sUnit” and the term “Transmitter” corresponds to “Baby’s Unit” in the rest of thisinstruction booklet.• The Home Connection Monitor System is not intended to replaceresponsible and proper parental supervision.• Check your child’s activity at regular intervals as this monitor will not alert parents to the silent activities of a child.• Before using your Home Connection Monitor System:- Read and follow all instructions carefully.- Read and observe all warnings on the product and in thisinstruction booklet.• To prevent entanglement with the adapter cord, NEVER place the cord in or near a crib or playpen. DO NOT place the Transmitter orReceiver anywhere its AC adapter cord could be within reach of children.• ALWAYS KEEP THE TRANSMITTER, RECEIVER AND AC ADAPTERSOUT OF REACH OF CHILDREN.• This product is not intended to be used as a medical monitor and its use should not replace adult supervision.• It is essential to check reception regularly. Please see the Testing Reception section for complete instructions.• The Transmitter is intended for indoor use only.• NEVER use the Transmitter or Receiver near water. For example, do notuse near a bathtub, bathroom sink, laundry tub, kitchen sink, in a wetbasement, etc.• Always unplug the AC adapters from wall outlets during long periods of non-use.• Position the Transmitter, Receiver and AC adapters to allow adequateventilation and prevent these components from overheating.• To prevent overheating, keep the Transmitter, Receiver and AC adaptersaway from heat sources such as radiators, heat registers, stoves or otherappliances (including amplifiers) which produce heat. Also keep thesecomponents out of direct sunlight.• Use only the AC adapters provided. Use of any other adapters may damage the Transmitter and/or Receiver. Plug the AC adapters intostandard household current only (120V AC outlet)! To prevententanglement and overheating, DO NOT use extension cords.• The AC adapters may become slightly warm to the touch during operation.This is normal.• Position the AC adapter cords so that they are not walked on or pinched byitems placed upon or against them, paying particular attention to cords atAC adapter plugs, wall plugs, and the point at which the cords attach to theTransmitter and Receiver.WARNING208038_inst_E_112103 12/10/03 2:00 PM Page 2
3• This product should be serviced only by qualified service personnel at DorelJuvenile Group when:-An AC adapter or its plug is damaged, -The Transmitter or Receiver are dropped,-Liquid has spilled into the Transmitter or Receiver or-The Transmitter or Receiver do not appear to operate normally or exhibit amarked change in performance• DO NOT attempt to service this product beyond that described in the Troubleshooting section at the end of these instructions. All other servicingshould be referred to qualified personnel at Dorel Juvenile Group.NOTE: The LEDs emit IR (infra red) light that is not harmful.TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER ORBACK OF TRANSMITTER. NO SERVICEABLE PARTS INSIDE. REFER SERVICING TODOREL JUVENILE GROUP CONSUMER RELATIONS (800) 544-1108.TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THISPRODUCT TO WATER OR MOISTURE. NEVER ATTEMPT TO OPEN THE CASE OF THETRANSMITTER. THIS IS DANGEROUS AND WILL VOID THE WARRANTY.CAUTIONWARNINGFCC InformationThis device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions (1) this device may not cause harmful interference, and (2) thisdevice must accept any interference received, including interference that may causeundesired operation.RADIO AND TELEVISION INTERFERENCEThis equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interferenceto radio communications. However, there is no guarantee that interference will not occurin a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the followingmeasures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Changes and Modifications not expressly approved by the manufacturer or registrant ofthis equipment can void your authority to operate this equipment under FederalCommunications Commissions rules.WARNING: Changes or modifications to this unit not expressly approved byDorel Juvenile Group could void the user’s authority to use the equipment.08038_inst_E_112103 12/10/03 2:00 PM Page 3
4• Lay out and identify all parts.• Do not return this product to the place of purchase. If any parts are missing, or if youare having difficulty using product visit our web site at www.safety1st.com. Or callConsumer Relations at (800) 544-1108. Have the model number (08038) and datecode (manufacturing date) ready before you call. The date code is located on thebottom of each Parent’s Unit.• The Recharging Battery is designed for many years of use, but if you should need toreplace it, the part number is ######.Keep These Instructions for Future UseMicrophoneSecure Sound LightsTalk ButtonChannel SelectorRoom Selector ButtonsScan ButtonOn/Off & Volume ControlSpeakerPower On & Low Battery IndicatorABCBFeatures and ComponentsDEFOn/Off SwitchPower On IndicatorMicrophoneChannel SelectorAC Adapter (5)Attachable Cord Shortener (3)Rechargeable Batteries (2)LKParent’s Unit (2)Baby’s Units (3)ACHFOKJMNNLOMEIDHGJGIPP08038_inst_E_112103 12/10/03 2:01 PM Page 4
5Installing Your Home Connection Monitor System• To prevent entanglement, only mount the Baby’s Unit in a location where itand its AC adapter cord are OUT OF REACH OF CHILDREN.• DO NOT mount the Baby’s Unit directly above heating vents, other heatproducing sources or in direct sunlight.• To prevent entanglement and overheating, NEVER use an extension cord.WARNINGTo Charge the Parent’s Units:IMPORTANT: You will need to fullycharge each Parent’s Unit BEFOREFIRST USE and when low batteryindicator is illuminated.1.Unscrew the two screws at the bottomof each Parent’s Unit. Insert theRecharging Battery with 2 pinconnector wire facing down. Connectthe two pin connector inside eachParent’s Unit. Replace the bottom andsecure screws (Figure 1).2.Connect an AC adapter into eachParent’s Unit and into a power outlet(Figure 1). It takes approximately 8hours to fully charge. 1RechargingBatteryScrewsNOTE:The Parent’s Units may use either the AC adapter or the rechargeable batteriesprovided. • When using batteries, check batteriesregularly. Amber LED indicates thebatteries are low. DO NOT rely onParent’s Unit when batteries are low.CAUTION3.For AC Power Use: Locate each Parent’s Unit and its AC adapter. Connect theAC adapter into the side of the Parent’s Unit. Connect the AC adapter into a poweroutlet.CAUTION: DO NOT use an adapter or batteries that did not come with thisproduct.For Battery Use: Charge the Parent’s Units as noted above. NOTE: If desired, slide the belt clip over your belt.2 PinConnector08038_inst_E_112103 12/10/03 2:01 PM Page 5
6Installing Your Home Connection Monitor System2To Set Up the Baby’s Units:4.Locate each Baby’s Unit and its ACadapter. Connect the AC adapterinto the bottom of each Baby’sUnit (Figure 2). If desired, wrap theexcess cord onto cord shortener.Connect the AC adapter into apower outlet. Place the Baby’s Uniton a flat surface 4 to 6’ (1.5 to 2 m)away from the baby. CAUTION: DO NOT use an adapterthat did not come with this product.ACAdapter5.Turn each charged Parent’s Unit and Baby’s Units to the On position. Be sure thatchannel I is selected on all Baby’s Units.NOTE: The channel selectors on the Parent’s Units are preset to channel I. Asecond channel is available if you experience interference. Please refer to theTroubleshooting section.Choose Locations:• For best sound quality and safety, place each Baby’s Unit 4 to 6’ (1.5 to 2 m) awayfrom the baby.• Be certain the Parent’s Unit and Baby’s Unit are set on the same channel (all Unitsare preset on channel I when packaged).• Check reception regularly.• Adjust the volume to a comfortable level for your environment.• Use each Parent’s Unit far enough away from the Baby’s Units so as not to getfeedback.• During use of the monitor, if the sound quality deteriorates you may be reaching thelimits of the monitor’s range. If this happens, you will need to move the Parent’s Unitsin closer proximity to the Baby’s Units.IMPORTANT: When choosing locations to set up the Baby’s Units and Parent’s Unitsfollow these guidelines:Baby’s UnitTo Use the Baby’s Unit and Parent’s Units:08038_inst_E_112103 12/10/03 2:01 PM Page 6
7Operating Your Home Connection Monitor System4On/OffVolumeControlTo Use the Baby’s Unit and Parent’s Units (continued):Scan Feature:8.The Parent’s Units can scan eachBaby’s Unit for three secondintervals. For example, Baby’s Unit Ais monitored for three seconds andthe corresponding colored LEDilluminates. Next, Baby’s Unit B ismonitored and so on. Press the Scanbutton to turn Scan On. To turnScan Off and listen only to oneBaby’s Unit, press the room selectorbutton that corresponds to theBaby’s Unit (Figure 5).Two-way Talk Feature:9.The two-way talk feature on eachParent’s Unit allows the parent tocommunicate with someone on thesecond Parent’s Unit. Press and hold6.Adjustthe volume by turning theknob on the side of each Parent’sUnit. Check the battery LED onthe Parent’s Units to be sure theunit is charged (green). If the LowBattery LED is illuminated amber,you need to recharge the Parent’sUnit (Figure 4).7.To listen to a Baby’s Unit press theroom selector button thatcorresponds to the Baby’s Unit thatyou want to monitor. Each Baby’sUnit is color coded to match thecorresponding button on theParent’s Units.Low BatteryLED(Amber)5Baby’sUnit AScanButtonBaby’sUnit B Baby’sUnit CTalkButtonthe talk button. Release button to listen (Figure 5).Secure Sound Lights:10.The 5 sound lights on the Parent’s Units indicate the sound level of the roomthat you are monitoring. The more noise in the selected room, the moresound lights will illuminate.CAUTION: Test the Parent’s Unit before each use. It is essential to check receptionregularly. IMPORTANT: The first time you use your Home Connection Monitor System, gothrough the section “To Test the Reception” with two adults.08038_inst_E_112103 12/10/03 2:01 PM Page 7
8Operating Your Home Connection Monitor SystemTo Test the Reception:11.Place each Baby’s Unit in a room near the baby. Have an adult speak intoeach Baby’s Unit at various levels (soft to loud) while another adult checkseach Parent’s Unit for the proper sound and reception. Try the Parent’s Unitin every location that it will be used. Try talking from one Parent’s Unit to theother. It is best to follow these guidelines for good reception:Guidelines for good reception:• The Baby’s Unit should be placed 4 to 6’ (1.5 to 2 m) away from the baby.• Be certain each Parent’s Units and corresponding Baby’s Unit are set on the samechannel (see Troubleshooting).• Check reception regularly by following Step 10 above.• Adjust the volume to a comfortable level for your environment.• Use each Parent’s Unit far enough away from the Baby’s Units so as not to getfeedback.• During use of the monitor, if the sound quality deteriorates you may be reaching thelimits of the monitor’s range. If this happens, you will need to move the Parent’s Unitin closer proximity to the Baby’s Unit.NOTE: It is possible for the Parent’s Units to pick up sounds or interference fromother signal producing devices including other audio or video monitors whichbroadcast in the 900 MHzrange. To minimize this potential problem, twoindependent channels have been provided. If interference becomes a problem on the preset channel, please refer to theTroubleshooting section at the end of these instructions.CAUTION: To protect your privacy, always turn the Baby’s Units off when not inuse. Always remember that you are using public airwaves. Sound may be broadcastto other receiving devices. Conversations, even from rooms near by, may be broadcast.NOTE:Do not return this product to the place of purchase. If you are having difficultyusing product visit our web site at www.safety1st.com or contact ConsumerRelations at (800) 544-1108. TroubleshootingProblemStatic or no sound on presetchannelPossible CauseChannel switches are not on thesame setting (I or II)Signal interference due tomonitors, cellular or cordlesstelephones, etc.Out of rangeSolutionCheck the channel switches onthe Baby’s Unit and Parent’s Unitto confirm they are on the samechannel (I or II)Try the other channelTurn the Baby’s Unit and Parent’sUnit off, wait a moment thenturn them back onBring Parent’s Unit unit closer toBaby’s Unit08038_inst_E_112103 12/10/03 2:01 PM Page 8
9Troubleshooting (continued)ProblemParent’s Unit’s power indicatordoes not illuminatePossible CauseParent’s Unit is not turned onBatteries are dead/Power is turned offAC Adapter not properlyconnectedSolutionSlide the button on each side ofParent’s Unit to the on positionMake certain that any light switchesthat control the power flow to thewall outlet are on (when using AC)Make certain that house fuses and circuit breakers are on (whenusing AC)Check AC Adapter jack-to-socketand plug-to-outlet connectionsAudio feedback (squealing) Baby’s Unit is too close to theParent’s UnitMove the Baby’s Unit furtheraway from the Parent’s UnitLower the volume on theParent’s UnitParent’s Unit not functioning orstatic or power LED is amberBatteries are lowWrong AC adapter usedNot within rangeIf amber LED lights or no LEDat all, change the batteriesIf you are not using batteries, becertain that you are using thecorrect AC adapter Move closer to the Baby’s UnitBaby’s Unit not functioning orpower LED is offBaby’s Unit is not turned onNot within rangeSlide the button on side of eachBaby’s Unit to the on positionBring Parent’s Unit unit closer toBaby’s UnitRecharging Battery for Parent’sUnit does not rechargeExceed Recharging Battery’s lifespanReplace Recharging Battery (seepage 5)3Channel Selector SwitchNOTE: To change the presetchannels, slide open the door onthe bottom of both Parent’s Unitand flip the switches for eachcorresponding Baby’s Unit to thedesired position. Be sure to changethe switch on the side of Baby’sUnits to the matching channel.Parent’s Unit has no sound Volume not turned up Adjust the volume control onthe Parent’s Unit08038_inst_E_112103 12/10/03 2:01 PM Page 9
10Dorel Juvenile Group, Inc. warrants to the original purchaser that this product(Home Connection Monitor System), is free from material and workmanshipdefects when used under normal conditions for a period of one (1) year from thedate of purchase. Should the product contain defects in material or workmanshipDorel Juvenile Group, Inc., will repair or replace the product, at our option, free ofcharge. Purchaser will be responsible for all costs associated with packaging andshipping the product to Dorel Juvenile Group Consumer Relations Department atthe address noted on the front page of this document and all other freight orinsurance costs associated with the return. Dorel Juvenile Group will bear the costof shipping the repaired or replaced product to the purchaser. Product should bereturned in its original package accompanied by a proof of purchase, either a salesreceipt or other proof that the product is within the warranty period. This warrantyis void if the owner repairs or modifies the product or the product has beendamaged as a result of misuse.This warranty excludes any liability other than that expressly stated previously,including but not limited to, any incidental or inconsequential damages.SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OFINCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONOR EXCLUSION MAY NOT APPLY TO YOU.THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAYALSO HAVE OTHER RIGHTS THAT MAY VARY FROM STATE TO STATE. One-Year Limited Warranty08038_inst_E_112103 12/10/03 2:01 PM Page 10

Navigation menu