Dorel Juvenile Group 48020T 900 MHz Color Baby Monitor User Manual

Dorel Juvenile Group 900 MHz Color Baby Monitor Users Manual

Users Manual

Table of ContentsImportant Safety Messages & Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2FCC Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Camera Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Monitor Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Child Monitor Operation and Channel Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Camera Location and Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Wall Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Table Top Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Monitor Location and Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Installing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8Monitor Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9System Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Television Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Problems and Solutions Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Important Safety MessagesTO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOTEXPOSE THIS PRODUCT TO WATER OR MOISTURE. NEVERATTEMPT TO OPEN THE CASE OF EITHER THE CAMERA OR MONITOR. THIS IS DANGEROUS AND WILL VOID THE WARRANTY.NO SERVICEABLE PARTS INSIDE. REFER SERVICING TO SAFETY1ST CONSUMER RELATIONS (800) 723-3065.IN CANADA CALL (800) 721-3389.WARNING3. ALWAYS KEEP THE CAMERA, TV/MONITOR AND AC ADAPTERS OUT OF REACH OF CHILDREN.4. This product is not intended to be used as a medical monitor and its use should not replace adult supervision. It is important that an adult stay within the viewing range of the 900 MHz Hand-Held Monitor and Television at all times during use.5. It is essential to check reception regularly. Please see the Reception section for complete instructions.6. The Camera and Monitor are intended for indoor use only.7. NEVER use the Camera or Monitor near water. For example,do not use near a bathtub, bathroom sink, laundry tub, kitchen sink, in a wet basement, etc.8. Always unplug the AC adapters from wall outlets during long periods of non-use.9. Position the Camera,Monitor and AC adapters to allow adequate ventilation and prevent these components from overheating.10. To prevent overheating, keep the Camera, Monitor and AC adapters away from heat sources such as radiators, heat registers, stoves or other appliances (including amplifiers) which produce heat.Also keep these components out ofdirect sunlight.11. Use only the AC adapters provided. Use of any other adapters may damage the Camera and/or Monitor. Plug the AC adapters into standard household current only (120V AC outlet)! To prevent entanglement and overheating,DO NOT use extension cords.12. The AC adapters may become slightly warm to the touch during operation.This is normal.13. Position the AC adapter cords so that they are not walked on or pinched by items placed upon or against them, payingparticular attention to cords at AC adapter plugs, wall plugs, and the point at which the cords attach to the Cameraand Monitor.14. This product should be serviced only by qualified service personnel at Safety 1st when:• An AC adapter or its plug is damaged,• The Camera or Monitor have fallen,• Liquid has spilled into the Camera or Monitor, or• The Camera or Monitor do not appear to operate normally or exhibit a marked change in performance15. DO NOT attempt to service this product beyond that described in the Problems and Solutions Guide at the end of these instructions.All other servicing should be referred to qualified personnel at Safety 1st.16. Retain these instructions for future reference.NOTE: The LED's on the Camera emit IR (Infra Red) light that is not harmful.FCC NoteNOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCCRules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.Thisequipment generates, uses and can radiate radio frequency energy and, if not installed and used according to the instructions,maycause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or television reception,which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Re-orient or relocate the receiving antenna,• Increase the separation between the equipment and receiver,• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected,• Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may causeundesired operation.Page 2 Page 31. Before using your Safety 1st 900 MHz In Sight Hand-Held TV-Video Monitor:• Read and follow all instructions carefully.• Read and observe all warnings on the product and in this instruction booklet.2. To prevent entanglement with the adapter cord, NEVER place the Camera in or near a crib or playpen. DO NOT place the Camera on any surface or mount it on any wall where the Camera or its AC adapter cord are within reach of children.The 900 MHz Hand-Held Monitor and Television is intended for indoor use only.Do not place the Camera where it will receive directsunlight indoors. Outdoor use may damage the Camera and/or Monitor.The outer surface of the Camera and Monitor can be cleaned with a cloth LIGHTLY dampened with water or a mild cleaning solution. Do not immerse any part of the 900 MHz Hand-Held Monitor and Television in water. As with any other electronic product, care should be exercised so as not to drop the product or physically damage it. Electronic components may be affected by such abuse.Care and MaintenanceCAUTION: Changes or modifications to this unit not expressly approved by Safety 1st, Inc.could void the user’s authority to use the equipment.
ContentsCamera 1 Wall AnchorFeatures and ComponentsCAMERA:TV-Video MonitorPage 4 Page 5(2)AC AdaptersRequirements:.Tools needed for wall mounting of Camera:Drill, 3/16” (4.8mm) drill bit, hammer, and Phillips head screwdriver (not included).4 “AA” alkaline batteries (not included) for TV-Video Monitor.Adult assembly is required.1 Screw(base)2173456891110AC ADAPTER:The AC Adapters are a low voltage power source that allows you to use your household electricity to run the 900 MHz Hand-Held Monitor and Television. The separate AC Adapters connect to the ACAdapter Jack in the Monitor and Camera . Bothplug into any standard 110 volt electrical outlet in your home.CAUTION: These adapters were made with a specific design for Safety 1st 900 MHz In Sight Hand-Held TV-Video Monitor. They cannot be used with any otherappliance. Never use a different type of adapter with this monitor.TV-VIDEO MONITOR:31107456891113122Top ViewBottom ViewON OFF EXT. ANT. BRIGHTNESS1. Power On (green) / Low Battery (red) LED Light2. 2" Color TFT Active Matrix Display Screen3. TV Tuning/Brightness Adjuster Buttons4. On/ Volume Control5. External Antenna Jack6. Earphone Jack7. Brightness/Tint Button8. Channel Selector9. Mode Switch (TV/Camera/Audio)10. TV-Video Antenna11. Battery Compartment12. Belt Clip13. AC Adapter Jack1. Channel Switch (A, B, or C) 2. Antenna3. Power Indicator4. Night Vision LED's:Allows Camera toautomatically adjust to darkened room5. Microphone6. Camera Lens7. AC Adapter8. ON/OFF Switch9. Tilt Adjustment Knob. Controls up anddown tilt of camera for optimal viewing10. AC Adapter Jack11. Base/Wall Mount
Monitor ReceptionBefore installing Wall Mount Screw, it is very important to test the video and sound reception of the 900 MHz Hand-Held Monitor andTelevision at the following times:• Before initial use• Regularly during use• Whenever you change the location of the Camera or MonitorTo Test: It is easiest for two adults to test reception. One adult should be present in the room with the Camera, while the other adultmoves the Monitor to several different locations throughout the house.As with any audio equipment, feedback or a high pitched shrillsound may occur if the Camera and Monitor are too close to each other. It is important to test sound quality and video reception in eachlocation in which you intend to use the 900 MHz Hand-Held Monitor and Television.To test the video reception, the adult present in the room with the Camera should place the Camera in the most appropriatelocation for monitoring the baby (on a table top, dresser, or against a wall). Direct the Camera lens toward the area you want to see onthe Monitor screen. (While testing, it may be helpful to place an object,such as a doll or stuffed animal, in the area you want to beviewing on the monitor.) Check the video reception on the Monitor screen. Adjust the quality of the picture using the brightnessadjustment knob on the back of the Monitor. Make sure you check reception in all areas in which you intend to use both the Monitor andCamera.The Camera has an Auto Sensor to allow the Camera to see clearly, automatically, even in a completely darkened room. In theNight Vision mode, the Picture will be black and white.To test sound reception quality,have the adult present in the room with the Camera speak in both a whisper and a normalconversation level at the location of the child being monitored. During sound testing, keep in mind the volume of your child’s sounds andtest accordingly.The Monitor must be placed far enough away from the Camera to prevent feedback noise from occurring. Usually thismeans placing the Monitor in a different room than the Camera is in.Operating Your 900 MHz Hand-Held Monitor and TelevisionAlways remember that you are using public airwaves when you use the Safety 1st 900 MHz Hand-Held Monitor and Television. Soundand video may be broadcast to other receiving devices. Conversations, even from rooms near the Camera,may be broadcast as well.CAUTION: To protect your privacy, always turn the Camera off when not in use.It is possible for the Monitor to pick up sounds or display interference from other signal producing devices including other audio or videomonitors which broadcast in the 900 MHz range.To minimize this potential problem, three independent channels have been provided foryour use.If you experience interference while using one channel setting, simply switch the Camera and Monitor to another channel. Selecting achannel is usually a one-time adjustment. If interference persists on all channels, please refer to the Problems and Solutions Guide at theend of these instructions.Camera Location and Set UpYou can position and adjust the Camera in a variety of ways to provide the best view of your baby at all times. The Camera can be easilymounted on a wall, or it can be simply placed on a stable, flat surface,such as a dresser, table top or shelving unit.IMPORTANT: Once you have selected a location for mounting, TEST the reception of the 900 MHz In Sight Hand-Held TV-Video MonitorBEFORE INSTALLING any wall mount screws. If interference or other problems occur, please refer to the Problems and Solutions Guideat the end of these instructions.Camera Wall Mount Installation• Using a 3/16” (4.8 mm) drill bit on an electric drill, drill a hole in the wall.• Place the Wall Anchor in the drilled hole.Tap gently with a hammer on the Wall Anchor until the end of the Wall Anchor is even or flushwith the surface of the wall as shown in Figure A.• Place the Screw in the Wall Anchor and tighten until there is a 1/4” (6.2 mm) gap between the wall and the Screw head as shown in Figure B.Page 6 Page 7Mounting the Camera on the Wall1/4" (6.2 mm)ABCDGroovesWARNING:In selecting a location to mount the Camera, keep the following things in mind:• To prevent entanglement, only mount the Camera in a location where it and its A/C adapter cord are OUT OFREACH OF CHILDREN.• For best viewing,mount the Camera approximately 6' (2m) away from the child.• Mount the Camera in a location where the camera lens will have an unobstructed view.Use the tilt and swivel adjustments to properly aim the Camera.• Allow adequate ventilation of the Camera when mounted on a wall. DO NOT mount the Camera directly above heating vents, other heat producing sources or in direct sunlight.• Make certain that the Camera will be mounted so that the AC adapter cord will reach an outlet.To prevent entanglement and overheating, NEVER use an extension cord.• Unwrap and fully extend the AC Adapter cord.NOTE: Two AC Adapters are included in the 900 MHz In Sight Hand-Held TV-Video Monitor. Use the Adapter with the longer cord with the Camera. Use only the AC Adapters included with the 900 MHz In Sight Hand-Held TV-Video Monitor.• Plug the jack on the Camera’s AC Adapter cord into the AC Adapter jack on the bottom of the Camera.• Hold the Camera so the underside of the base/wall mount faces you.• Insert the AC Adapter cord into the groove on the underside of the Camera base/wall mount as shown in Figure C. Make certain the AC Adapter cord stays in the groove as you place the Camera on the wall mount Screw.• Slide the Camera base/wall mount down on the Screw to secure it to the wall as shown in Figure D.NOTE: If the Camera does not slip easily onto the wall mount Screw, remove the Camera from the wall and slightly loosen the Screw.• Plug AC Adapter into a standard wall outlet.• Wrap up and secure any excess AC Adapter cord.Camera Table Top Set UpThe Camera can be positioned on any stationary flat surface, such as a dresser, table top or shelving unit. Position the cameraapproximately 6' (2M) away from the desired object.NOTE: Use only the AC adapters included with the 900 MHz In Sight Hand-Held TV-Video Monitor.• Unwrap and fully extend the AC adapter cord.• Plug AC Adapter into a standard wall outlet.• Wrap up and secure any excess AC adapter cord.WARNING: TO PREVENT THE RISK OF ENTANGLEMENT, NEVER PLACE THE CAMERA IN CRIB OR PLAYPEN. ALWAYS POSITIONTHE CAMERA AND ITS AC ADAPTER CORD OUT OF CHILD’S REACH.
Monitor Set UpThe portable Monitor operates by use of 4 AA alkaline batteries (not included) or the AC Adapter cord included with the 900 MHz In SightHand-Held TV-Video Monitor for AC Monitor power.REMEMBER: Use only the AC Adapter included with the 900 MHz In Sight Hand-Held TV-Video Monitor for power.IMPORTANT NOTES:• Keep the Monitor out of reach of children.• Keep the Monitor upright for best reception.Page 8 Page 9Installing the Batteries• Do not submerge any part of TV/Video Monitor in water.• Remove batteries when stored for long periods of non-use.• Remove spent batteries promptly.• Rechargeable batteries may be used but must not berecharged in the unit.• Only an adult should charge rechargeable batteries.• Non-rechargeable batteries must not be recharged.• DO NOT short circuit supply terminals.• Insert batteries oriented for the correct polarity (as shown in battery compartment).WARNINGSTEP 1 Locate the battery compartment door on the back of the TV/Monitor,and unscrew the battery door in the direction of the arrow to remove as shown in Figure A.STEP 2 Install 4 AA alkaline batteries (not included) into the battery compartment as shown. Ensure the (+) and (-) symbols match those shown in the battery compartment.STEP 3 Re-align battery door and screw into position.NOTE: The TV/Monitor will not work in battery mode if batteries are not installed properly.After several hours of continuous use, the Power On/Low Battery LED Light may turn solid red, indicating that the batteries need to be replaced. Please follow instructions noted above for the installation of new batteries.NOTE: We recommend using household electrical power when possible to conserve battery power.A• Place the Monitor where you can see and hear it.• To use household power, unwrap and fully extend the AC adapter cord, and plug the jack on the Monitor’s AC Adapter cord into the AC adapter jack (DC 12V IN) on the side of the Monitor.Then plug the AC adapter into a standard wall outlet. Be certain to wrap up and secure any excess AC adapter cord.• Turn the Monitor “ON”by:-Sliding the Mode Switch to Camera.-Sliding the channel switch to either A,B or C to match the camera setting.• Adjust the volume rotary dial to a comfortable sound level.• If you experience interference switch both the Camera and the Monitor to another channel using the Channel Selector.To Adjust Brightness and Tint:• To adjust brightness, press the Brightness/Tint Button on top of the TV-Video Monitor.Then use the TV Tuning/Brightness Adjuster Buttons to make the picture lighter or darker as needed.• To adjust tint, press the Brightness/Tint Button twice.Then use the TV Tuning/Brightness Adjuster Buttons to change the tint as needed.Monitor OperationCamera Operation• Set Camera and Monitor to the same channel.• Slide the ON/OFF switch on the top of the Camera to the “ON”position.To Adjust:• Turn the tilt adjustment knob counter-clockwise just enough to loosen the camera.Move the camera up or down to the desired position and tighten the camera in place by turning the tilt adjustment knob clockwise.DO NOT OVER TIGHTEN.• Swivel the camera from side-to-side to obtain desired position.NOTE: Camera will turn approximately 180°. Do not attempt to turn it past 180°.DO NOT attempt to adjust the small antenna on Camera or Monitor.Using the Audio Only FeatureThe Audio Only feature allows the Monitor to be used without the picture in a sound only mode. To use the Audio Only feature, set the Mode Switch on the bottom of the Monitor to “AUDIO”. This will allow the Monitor to receive sound only without picture.Using the Monitor as a Television1. Switch the TV/CAMERA/AUDIO mode to TV.2.Tune the TV to the desired station using the TV Tuning/Brightness Adjuster Buttons.You can either depress the Buttons quickly to move through the channels one at a time, or hold the Button down to scroll through the channels.3.Adjust volume.4.Adjust the telescoping antenna for best picture.Note: The Camera has Night Vision LED’s that allow the Camera to automatically adjust to adarkened room.The Monitor will automatically switch to black and white reception at thistime, providing you with a clear view of baby at night.
Problem Possible Cause SolutionSound, but no picture (continued) Monitor is set to “Audio” Adjust switch to “TV”or “Camera”modeSignal interference due to Test reception by moving the Camera other nursery monitor, and/or Monitor to different locations cordless telephones, etc. throughout the house. Relocate the Camera and/or MonitorPicture, but no sound Volume not turned up Adjust the volume control on the Monitor.Change channel setting to both the Camera and MonitorOut of range Bring Camera unit closer to MonitorPicture flickers in low light Object too close to Camera Remove objects that are tooclose to the Camera or movethe Camera/MonitorCamera or Monitor near Test reception by moving Camera metal concentration and/or Monitor to different locations throughout the houseSignal interference due to Change the channel setting on the other monitors, cordless Camera and Monitor or cellular telephones, etc.Identify and eliminate the sourceof interferenceAudio feedback (squealing) Monitor is too close to Move the Monitor further away from the Camera the CameraVolume is set too high Lower the volume on the MonitorDark picture at night Night Vision LED’s not With room lights off, check Camera to be functioning properly certain that all Night Vision LED's are glowing red if not, contact the Consumer Relations Department at Safety 1stPage 10 Page 11TroubleshootingProblem Possible Cause SolutionCamera’s power indicator light Camera is not turned “ON” Slide the ON/OFF switch to the does not light Power is turned off “ON” positionMake certain house fuses and circuit breakers are onMake certain that any light switches that control the power flow to the wall outlet are onAC Adapter not Check AC Adapter jack-to-socket and properly connected plug-to-outlet connectionsMonitor screen does Monitor is not turned “ON” Turn the Monitor on. Slide Mode not illuminate and no sound for video or television use Switch to Camera for Monitor use or to TV for television use. May be in Audio Only modeBatteries may be dead Replace batteries, 4AAPower is turned off Make certain house fuses andcircuit breakers are onMake certain that any light switches that control the power flow to the wall outlet are onAC Adapter not Check AC Adapter jack-to-socketproperly connected and plug-to-outlet connections. Becertain it is plugged into the ACjack (DC 12V IN)No sound or picture Channel switches are not on Check the channel switches on the the same setting (A, B, C) Camera and the Monitor to confirm they are on the same channel (A, B, C)Signal interference due to Change the channel setting on both other Monitors, cordless the Camera and the Monitoror cellular telephones, etc Turn both the TV and Camera off.Wait a moment and turn them back onSound, but no picture In TV Mode, may need to Use TV Tuning/Brightness Adjusterchange channels Buttons to tune the television.In Monitor Mode, may need Press Brightness Button to activate.Then to adjust brightness use TV Tuning/Brightness Adjuster Buttons to adjust brightness as neededCamera or Monitor near Test reception by moving the metal concentration Monitor closer to the Camera or by moving the Camera and/or Monitor to different locations throughoutthe house. Relocate the Cameraand/or MonitorWarranty InformationONE (1) YEAR LIMITED WARRANTYSafety 1st, Inc., warrants to the original owner of this product that the Nursery Monitor is free from defects in materials andworkmanship for a period of one (1) year from the date of the original purchase. If this monitor fails to function when used asdirected under normal conditions, within the one (1) year period, Safety 1st will either repair or replace the product at our option,free of charge, when it is returned complete and in its original packaging, prepaid postage, and insured to Safety 1st ConsumerRelations Department (see appropriate address on next page). Product must be accompanied by a proof of purchase,either a bill ofsale, receipted invoice, or other proof that the monitor is within the warranty period.Safety 1st will bear the cost of repairing orreplacing the product and shipping it back to you.This warranty does not apply to a Nursery Monitor that has been damaged as a result of improper maintenance, accidents,improper voltage supply or other misuse.The warranty is also void if the owner repairs or modifies the product in any way.Safety 1st is not liable for any incidental or consequential damages with regard to this product.The warranty also excludes any liability other than what is stated above. No other warranties are given.LEGAL RIGHTS VARY FROM STATE TO STATE.SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONOF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.IMPORTANT NOTE: ONLY USE THE ADAPTERS SUPPLIED FOR THIS NURSERY MONITOR.USE OF OTHER ADAPTERS WILL VOID THIS WARRANTY.
If you have any questions or comments, please call our toll free Consumer Relations number. If you are not completely satisfied, please return with proof of purchase to:Safety 1st Inc., 45 Dan Road, Canton, MA 02021 USA 800-723-3065Safety 1st Canada Inc., 84 rue Deslauriers,Ville St-Laurent, Quebec H4N 1X1 Canada 800-721-3389Safety 1st Europe Ltd., Isopad House, Shenley Road, Borehamwood, Hertfordshire WD61TE UK +44(0)20 8236 0707Made in CHINA to Safety 1st quality specifications. ©2000 Safety 1st,Inc.www.safety1st.comStyles and colors may vary4/00Page 1Thank you for purchasing the Safety 1st 900 MHz Hand-Held Monitor and Television. This extraordinarily versatile, state-of-the-art system featuresfull-color viewing when used as a monitor during the day. At night, Infra RedLED’s provide you with a clear black and white image of baby in a darkenedroom. The 900 MHz Hand-Held Monitor and Television can also be used as afull-color TV, for years of added use. This unique monitor also features 3channel selections for optimal performance as well 900MHz RF technology forsuperior clarity and additional privacy. Both the Camera and the VideoMonitor/TV are AC powered for use with convenient household electricity, andthe Monitor/TV can also be powered with 4 AA alkaline batteries (notincluded) for additional portability.We are sure that you will find the 900 MHz Hand-Held Monitor andTelevision convenient and easy to use. To ensure that you benefit from all of thegreat features that your monitor offers, and to make sure that you use it properly,we urge you to:Please read all instructions carefully before using this product. Keep these instructions for futurereference. If you have any questions, please call our Consumer Relations number at (800)723-3065.In Canada call (800)721-3389.CAUTION:• THE 900 MHz HAND-HELD MONITOR AND TELEVISION IS NOT INTENDED TO REPLACE RESPONSIBLE AND PROPER PARENTAL SUPERVISION.• YOU SHOULD CHECK YOUR CHILD’S ACTIVITY AT REGULAR INTERVALS AS THIS MONITOR WILL NOT ALERT PARENTS TO THE SILENT ACTIVITIES OF A CHILD.900 MHz Hand-Held Monitor and TelevisionTelevision and Baby Monitor in one! No. 48020Owner’s ManualIMPORTANT!Please do not return this product to the store! Your questions and comments are important to us!Thank you for purchasing this quality product from Safety 1st. We are confident you will bepleased with its many features and performance. If you are having any problems assembling,installing, or using this product, please call us. We will be very happy to answer any questionsthat you may have. Many times there is a simple solution to any problem that may occur.Talking to us directly will be convenient and save you time.Call our Consumer Relations Department toll-free at (800) 723-3065; in Canada call (800) 721-3389 from 9:00 am to 5:00 pm (EST) Monday - Friday.We will gladly answer any and all of your questions about this product.

Navigation menu