Dorel Juvenile Group 49270T Nursery Monitor User Manual Users manual

Download:
Mirror Download [FCC.gov]
Document ID	128532
Application ID	7tx3Wy//6k38KDmHA1tVfg==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.88kB (111027 bits)
Date Submitted	2000-12-13 00:00:00
Date Available	2000-12-13 00:00:00
Creation Date	2000-10-25 15:39:59
Producing Software	Acrobat Distiller 4.0 for Macintosh
Document Lastmod	2000-10-25 15:40:01
Document Title	Users manual

49MHz Two-Way Intercom Monitor
No. 49270
Owner’s Manual
Introduction
Thank you for purchasing the Safety 1st Two-Way Intercom Monitor.
We are confident that this advanced system will help keep you in tune with your baby’s
every sound, offering you two-way communication, clear reception, and portability.
Communication
• Two-way communication feature lets you soothe baby with your own voice or talk
to another adult
• Sound Lights let you see baby’s sound level
Reception
• 49 MHz technology provides superior clarity
• Extended range up to 400' (122 meters)
• Two channels to help minimize interference
Portability
• Both Units can run on battery power while you are on the go
• Parent’s Unit features a handy belt-clip for portability
• Units also run on household electricity – two A/C adapters included
Please read all instructions carefully before using the 49MHz Two-Way Intercom
Monitor. Keep these instructions for your future reference. If you have any
questions, please call our toll-free Consumer Relations number: (800) 723-3065.
In Canada, please call (800) 387-2229.
CAUTION:
• THE TWO-WAY INTERCOM NURSERY MONITOR IS NOT INTENDED
TO REPLACE RESPONSIBLE AND PROPER PARENTAL SUPERVISION.
• YOU SHOULD CHECK YOUR CHILD’S ACTIVITY AT REGULAR
INTERVALS AS THIS MONITOR WILL NOT ALERT PARENTS TO THE
SILENT ACTIVITIES OF A CHILD.
• KEEP ALL PARTS OF THIS MONITOR OUT OF REACH OF CHILDREN!
Page 1
WARNING: Changes or modifications to this unit not
expressly approved by Safety 1st, Inc. could void the
user’s authority to use the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following 2 conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The Baby’s Unit carrier frequency on channel A is 49.830 MHz and on
channel B is 49.845 MHz. The Parent’s Unit carrier frequency on channel A
is 49.875 MHz and on channel B is 49.890 MHz. The field strength is 80 dB
microvolts per meter at 3 meters.
Safety Instructions
WARNING
• TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT
EXPOSE THIS PRODUCT TO WATER OR MOISTURE. NEVER
TOUCH THE END OF THE ADAPTER CORD WHEN THE ADAPTER
IS PLUGGED INTO AN ELECTRICAL OUTLET.
• TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE
COVER OR BACK. NO SERVICEABLE PARTS INSIDE. REFER TO
SAFETY 1ST CONSUMER RELATIONS: (800) 723-3065.
IN CANADA CALL (800) 387-2229.
Page 2
Safety Instructions
HEED WARNINGS: All warnings on the Two-Way Intercom Monitor and operating instructions
should be adhered to.
WATER AND MOISTURE: The Two-Way Intercom Monitor should not be used near water, for
example, near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement, near a
swimming pool, etc.
VENTILATION: The Two-Way Intercom Monitor should be placed so that its location does not
interfere with proper ventilation of the unit. For example, it should never be situated on a bed,
sofa, rug or similar surface that may block ventilation.
HEAT: The Two-Way Intercom Monitor should be kept away from heat sources such as radiators,
heat registers, stoves or other appliances that produce heat.
AC POWER SOURCE: The Two-Way Intercom Monitor should be connected only to the AC Adapters
supplied with the Unit.
POWER CORD PROTECTION: The power supply cord should be routed so that it is not likely to be
walked on or pinched by items placed upon or against it. Pay particular attention to the cord at the
plug, convenience receptacle, and at the point it exits from the AC Adapters.
CLEANING: Use a dry cotton cloth to keep the Two-Way Intercom Monitor free from dust.
Do not use water!
NON-USE PERIODS: The power cords of the Two-Way Intercom Monitor should be unplugged
from the outlet when unused for long periods of time. The batteries should also be removed
during these periods.
OBJECT AND LIQUID ENTRY: Care should be taken so that objects do not fall onto the product,
and liquids are not spilled into the enclosure through the openings.
DAMAGE REQUIRING SERVICE: The Two-Way Intercom Monitor should be serviced by qualified
personnel when:
A: The power supply cord or plug has been damaged.
B: Objects have fallen or liquid has been spilled onto the product.
C: The Monitor has been exposed to rain.
D: The Monitor does not appear to operate normally or exhibits a marked change in its performance.
E: The Monitor has been dropped or the enclosure damaged.
Contents
Parent’s Unit
(Requires one 9 volt alkaline
battery to operate in portable
mode. Not included.)
Baby’s Unit
(Requires one 9 volt alkaline
battery to operate in portable
mode. Not included.)
2 AC Adapters
Page 3
Features and Components - Parent’s Unit
On/Volume Dial
Power On (green)/Low Battery (amber) LED Indicator
Push to Talk Button
Channel Selector
LED Sound Lights (4)
Microphone
Antenna – turns 90° clockwise
to facilitate horizontal belt clip
AC Adapter Jack
Belt Clip
CHANNEL
10 Battery Compartment
(1 screw in door)
10
AC-9V IN
Features and Components - Baby’s Unit
AC-9V IN
On/Volume Dial
Power On (green)/Low Battery (amber)
LED Indicator
Two-Way Activation Button
Two-Way Mode LED (red) Indicator
Channel Selector
Antenna
Microphone
Speaker
AC Adapter Jack
10 Battery Compartment Door
10
CHANNEL
AC Adapters
The AC Adapters are low voltage power sources that allow you to use your household
electricity to run the Parent’s and Baby’s Units. They connect to the AC Adapter jacks
in the Parent’s Unit and in the Baby’s Unit, and plug into any standard electrical outlet.
CAUTION: These Adapters were made with a specific design for this Safety 1st
Two-Way Intercom Monitor. They cannot be used with any other appliance. Never
use a different type of Adapter with this monitor.
WARNING: Never touch the end
of the adapter cord when the adapter is
plugged into an electrical outlet.
Page 4
Operating your 49MHz Two-Way Intercom Monitor
Follow these instructions to operate your 49 MHz Two-Way Intercom Monitor. Reference the
illustrations on page 4 for the location of all features described in these instructions.
Baby’s Unit:
For best results, place the Baby’s Unit on a table near the crib or bed. It should be
facing the baby’s head as close to the crib as possible, but out of baby’s reach.
-9
IN
To Use Baby’s Unit:
STEP 1 To use household power, plug the round end of adapter cord into the jack on the
Baby’s Unit, then plug the adapter into an electrical outlet.
NOTE: Battery power is available when one 9 volt alkaline battery (not included) is
installed in the Baby’s Unit. However, it is not recommended to use the battery power for
extended periods when household power is available.
STEP 3 Turn Unit on by using On/Volume Dial. Power On LED should illuminate solid green.
STEP 4 Set Baby’s Unit to channel “A”. If you hear interference, switch both Units to channel “B”.
-9
IN
NOTE: If you experience a power failure, the Baby’s Unit WILL NOT
automatically switch to battery power. You must disconnect the AC Adapter
from the Baby’s Unit and insure that (1) 9 volt alkaline battery (not included)
is installed for battery power.
To Install Battery (for use in Portable Mode):
(One 9 volt alkaline battery required, not included)
STEP 1 Locate battery compartment door on bottom of the Baby’s Unit as
shown in Figure A. Using Phillips head screwdriver, remove the screw to take
off the battery compartment door.
STEP 2 Snap 9 volt alkaline battery onto the battery clip, and return to battery
compartment as shown in Figure B. Replace battery compartment door and
secure with Phillips screwdriver, taking care not to over tighten.
NOTE: Power On/Low Battery LED Indicator illuminates (amber) when batteries
need replacing.
AC
Parent’s Unit
-9V
IN
To Use Parent’s Unit:
STEP 1 To use household power, plug the round end of adapter cord into the
AC Adapter Jack on the Parent’s Unit, then plug the adapter into an electrical
outlet. Turn the On/Volume Dial to “ON” and set at an appropriate volume level
to hear baby at all times. The Power On LED Indicator on the Parent’s Unit
should be illuminated solid green.
NOTE: If you experience a power failure, the Parent’s Unit WILL NOT
automatically switch to battery power. You must disconnect the AC
Adapter from the Parent’s Unit and ensure that one 9 volt alkaline
battery (not included) is installed for battery power.
AC
-9V
IN
NOTE: If you experience static or noise interference, you may need to change
channels on both Units.
STEP 2 To clip over waist band or belt, as shown in Figure E, rotate antenna 90°.
To Install Battery (for use in Portable Mode):
(One 9 volt alkaline battery required, not included)
STEP 1 Locate battery compartment door on back of the Parent’s Unit as
shown in Figure C. Using Phillips head screwdriver, remove the screw to take off
the battery compartment door.
STEP 2 Snap 9 volt alkaline battery onto the battery clip, and return to battery
compartment as shown in Figure D. Replace battery compartment door and
secure with Phillips screwdriver, taking care not to over tighten.
NOTE: Power On/Low Battery LED Indicator illuminates (amber) when batteries need replacing.
NOTE: If you experience static or noise interference, you may need to change channels
on both Units.
Page 5
Intercom Mode
How to Operate
STEP 1 Depress Two-Way Activation Button on Baby’s Unit. Two-Way Mode LED will illuminate solid red.
STEP 2 Set volume on Baby’s Unit to desired level.
STEP 3 Press the “Push to Talk” Button on Parent’s Unit and speak directly into Microphone. “Push to Talk” Button must
be depressed while you speak for Baby’s Unit to receive communication.
Note: If interference is heard, switch both Units to the other channel.
Operating Tips
• Make sure both Units are on the same channel. Even though you may hear your baby’s sounds, proper use of this
system requires that both units be on the same channel. If on different channels, signals from Baby’s Unit can be
strong enough to be picked by Parent’s Unit, however, there will be a lot of static.
• When using AC adapter, make sure electrical outlet has power. Some electrical outlets are powered through a wall
switch in the room. When Baby’s and Parent’s Units are plugged in and turned “ON”, the power indicator light should
be lit. If it is not, turn wall switch “ON”.
Troubleshooting
Problem
Possible Cause
Solution
• Power On LED not working
• Battery may be dead, 9-volt battery
needs to be replaced
• Replace 9-volt battery
• Make sure wall outlet is working
• Power is not getting to the unit
• Make sure unit is properly plugged into
the wall and outlet is switched ON
• Static or interference in the signal
transmission
• Baby’s and Parent’s Units may be set on
different channels
• Appliances with loud fans near Units may
be blocking transmission
• Local interference from electrical or radio
frequency appliance near your location
• Make sure both Units are on the same
channel (A or B)
• Turn off the appliances that may be
causing interference
• Reduce the distance between the
two Units
• Unit may be under fluorescent lights,
turn off lights
• Switch channel setting on both Parent’s
and Baby’s Units
• Parent’s Unit is making loud noises
• Units are too close together
• Parent’s Unit needs to be at least 3
meters (10 feet) away from the Baby’s Unit
• Parent’s Unit is picking up noises from
outside your home
• Neighbors may have a baby monitor or
cordless phone
• Change both Units to the alternate
channel (A or B)
• Weak sound coming from Unit
• Batteries may be weak
• Units may be too far away from
each other
• Check batteries, replace if necessary
• Move the Units closer
• Baby’s Unit is set for Intercom Mode
but not receiving communication from
Parent’s Unit
• Parent’s “Push to Talk” Button is not
being continuously depressed while
parent is speaking
• Continuously hold “Push to Talk” Button
while speaking into microphone for Baby’s
Unit to receive complete communication
Page 6
IMPORTANT!
Please do not return this product to the store!
Your questions and comments are important to us!
Thank you for purchasing this quality product from Safety 1st. We are
confident you will be pleased with its many features and performance. If you
are having any problems assembling, installing, or using this product, please
call us. We will be very happy to answer any questions that you may have.
Many times there is a simple solution to any problem that may occur. Talking
to us directly will be convenient and save you time.
Call our Consumer Relations Department toll-free at (800) 723-3065;
in Canada call (800) 387-2229
from 9:00 am to 5:00 pm (EST) Monday – Friday.
We will gladly answer any and all of your questions about this product.
Page 7
Warranty Information
ONE (1) YEAR LIMITED WARRANTY
Safety 1st, Inc., warrants to the original owner of this product that the Nursery Monitor is free from defects in materials
and workmanship for a period of one (1) year from the date of the original purchase. If this monitor fails to function when used as directed under
normal conditions, within the one (1) year period, Safety 1st will either repair or replace the product at our option, free of charge, when it is
returned complete and in its original packaging, prepaid postage, and insured to Safety 1st Consumer Relations Department (see appropriate
address below). Product must be accompanied by a proof of purchase, either a bill of sale, receipted invoice, or other proof that the monitor is
within the warranty period. Safety 1st will bear the cost of repairing or replacing the product and shipping it back to you.
This warranty does not apply to a Nursery Monitor that has been damaged as a result of improper maintenance, accidents, improper voltage supply
or other misuse. The warranty is also void if the owner repairs or modifies the product in any way. Safety 1st is not liable for any incidental or consequential damages with regard to this product. The warranty also excludes any liability other than what is stated above. No other warranties are
given.
LEGAL RIGHTS VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
IMPORTANT NOTE: ONLY USE THE ADAPTERS SUPPLIED FOR THIS TWO-WAY INTERCOM MONITOR.
USE OF OTHER ADAPTERS WILL VOID THIS WARRANTY.
If you have questions or comments, please call our Consumer Relations number.
All Safety 1st products are guaranteed. If you are not completely satisfied, please return with proof of purchase to:
Safety 1st, Inc., 45 Dan Road, Canton, MA 02021 USA 800-723-3065
Safety 1st Home Products Canada Inc., 804 rue Deslauriers, Ville St-Laurent, Quebec H4N 1X1 Canada 800-387-2229
Safety 1st (Europe) Limited, Isopad House, Shenley Road, Borehamwood, Hertfordshire WD61TE UK +44(0)20 8236 0707
Made in CHINA to Safety 1st quality specifications. ©2000 Safety 1st, Inc.
www.safety1st.com
Styles and colors may vary.
Page 8

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Create Date                     : 2000:10:25 15:39:59
Producer                        : Acrobat Distiller 4.0 for Macintosh
Modify Date                     : 2000:10:25 15:40:01-04:00
Page Count                      : 8

EXIF Metadata provided by EXIF.tools