Dowtelecom DTP-800 Cellular CDMA WLL Phone User Manual DTP800 1900 user manual
Dowtelecom Inc. Cellular CDMA WLL Phone DTP800 1900 user manual
UserManual.wiki
>
Dowtelecom
>
DTP 800 User Manual
User Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![DTP-800/DTP-1900 Operating Manual 10 2.2 Keypad As shown in the figure below, there are 12-Dial Button and 10-Function Button in this phone. Figure : 2.2.1 2.2.1 DND/MUTE & RCL DND/MUTE - Use this button to set on/off the [DND(Do Not Disturb)] function if you don’t want to answer the incoming call in idle-state. (Reference 3.8) - Use this button to set on/off the [MUTE] function if you don’t want to send sound to the calling party through the handset or microphone during the conversation. RCL Use this button to find the last dialed phone number and to search the stored number in the Phone Book. STORE MENU CLR RCL DND/MUTE MSG/VAS SPK SND/RDL 3DEF 6MNO 5JKL 8TUV 7PQRS 9WXYZ 1 0OPER * # 4GHI 2ABC RCL DND/MUTE](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-10.png)
![DTP-800/DTP-1900 Operating Manual 11 <Note> DND/MUTE & RCL and MSG/VAS & CLR buttons are designed as an one -button as shown in figure 2.2.1. But these buttons separately operate the upper side and bottom side of the button to work their own function. 2.2.2 MENU Use this button to set the [MENU] mode or return to Idle-state. 2.2.3 UP / DOWN Use this button to set the [MENU] mode, adjust the ringer and voice volume, and store/find the phone number in the Phone Book. 2.2.4 STORE Use this button to store the Phone Numbers and setting-value under the [MENU] mode. MENU STORE](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-11.png)
![DTP-800/DTP-1900 Operating Manual 12 2.2.5 MSG/VAS & CLR (Clear & Recall) MSG/VAS - Use this button if you want to retrieve the text message of SMS(Short Message Service) transmitted and received during the idle-state. - Use this button to make a call to VMC(Voice Message Center) direct to retrieve the voice mail after picking up the handset or setting the speakerphone on. CLR Use this button to erase the number when you dialed incorrectly or when you stored the number in the Phone Book incorrectly. 2.2.6 SPEAKER [SPK] Use this button to make a call or receive a call by using speaker phone. 2.2.7 SEND & REDIAL [SND/RDL] Use this button to send the dialed number when you make a call and redial the last number dialed. CLR MSG/VAS](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-12.png)
![DTP-800/DTP-1900 Operating Manual 13 2.2.8 Dial Button(0~9, * , # ) - Use this button to store the phone number - There are small alphabets beside the numeric number on the each Dial Button. It is used to store the name related with the phone number when you want to store the phone number. <Example for use> If you want to store “DOWTEL3”, follow below procedure. As shown in the example above, the output alphabet character is serially displayed on the LCD screen when you press the button repeatedly. <Note> You can store the name with only uppercase character. 3→6→6→6→9→8→3→3→5→5→5→3→3→3→3 → [STORE] D O W T E L 3](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-13.png)
![DTP-800/DTP-1900 Operating Manual 14 2.3 ICON The various icons are displayed in the first line on the LCD screen to indicate the setting-status and operating-status of the phone. 2.3.1 RSSI Icon - Indicate the strength of received signal. It is closely related with the quality of service. - There are 5 bars with different length. It is the best condition if all bars are displayed beside the Antenna. symbol. - When there is only 1-bar on the screen, it means poor service condition. With flashing icon, the phone is capable of only marginally dependable phone operation, means phone can be disconnected. - When there is no bar on the screen, you cannot make a call because there is no received signal from the service provider in your area. 2.3.2 Connecting Icon - Indicate the phone is processing a call when you press the [SND/RDL] button to make a call. - This icon is displayed with the “Connecting…” message. 2.3.3 Off-Hook Icon - Indicate the Hook Switch Mode of the phone. - It is displayed when the handset is picked up from the phone.](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-14.png)
![DTP-800/DTP-1900 Operating Manual 16 2.3.8 Battery Icon - Indicate the strength of the battery installed inside the phone - The battery strength is displayed 5-step. - When the battery strength is weakening, the phone beeps to request the recharge of the battery. 2.3.9 DND (Do Not Disturb) Icon - Indicate the status that user set DND function on to deny the incoming call when user don’t want to answer the incoming call. - During this icon is flashing, the phone doesn’t answer to the incoming call. 2.3.10 Message Icon - Indicate the status that the phone is received the Text Message and/or Voice Message. - When the message is received, this icon is displayed on the screen with the indicate-tone. - You can read the received message and retrieve the voice mail through the Voice Mail Center (VMC) in the system using the [MSG/VAS] button.](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-16.png)
![DTP-800/DTP-1900 Operating Manual 19 3. Basic Function 3.1 Making Calls 3.1.1 Using the Handset ▶ Pick up the handset and dial the phone number you want to make a call. ▶ Press the [SND/RDL] button . ▶ The call is connected. 11:11 am Nov 11 (Sun) 1001234 1001234Connecting… 100123400:01](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-19.png)
![DTP-800/DTP-1900 Operating Manual 20 3.1.2 Using the Speaker Phone ▶ Press the [SPK] button and dial the phone number you want to make a call. ▶ Press the [SND/RDL] button. ▶ The call is connected. 1001234Connecting… 100123400:01 1001234](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-20.png)
![DTP-800/DTP-1900 Operating Manual 21 3.1.3 On-Hook Dialing ▶ Dial the phone number, and then press the [SND/RDL] button. ▶ The speaker phone operates automatically, and then the call is connected. 3.1.4 Redial the Last Number called <Method 1> ▶ Pick up the handset or press the [SPK] button, and then press [SND/RDL] button. (figure 3.1.3-1) 1001234 Connecting… (Figure 3.1.4-1) 1001234 Connecting… (Figure 3.1.3-2) 1001234 00:01](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-21.png)
![DTP-800/DTP-1900 Operating Manual 22 ▶ The last number dialed is connected automatically. <Method 2> ▶ Press the [SND/RDL] button, and then the speaker Phone operates automatically. ▶ The last number dialed is connected. 3.1.5 Speed Dial You can store up to 99 phone numbers in this phone using 2-digit addresses (01~99). The stored numbers in the Phone Book allow you to make a call simply by just press these addresses. And you can search and edit the number in the Phone Book. The method of store/search/edit of the phone number is explained next chapter. 3.1.5.1 One-Touch Dialing This function allows you to simply make a call just pressing the memory station number ([0] ~ [9]). (Figure 3.1.4-2) 1001234 00:01 (Figure 3.1.4-3) 1001234 00:01](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-22.png)
![DTP-800/DTP-1900 Operating Manual 23 <Method 1> ▶ Pick up the handset or press the [SPK] button. ▶ Press the memory station number stored in the address [1] ~ [9] for over 2 seconds then the stored number dialed, or press the memory station number shortly, and then press the [SND/RDL] button. (Example) When you want to make a call to the number stored in address [1], press the [SND/RDL] button after press [1] button shortly or press [1] button for over 2 seconds. ▶ The number in the Phone Book is connected. <Method 2> ▶ Press the button of the phone number stored in the address [1] ~ [9], and then press the [SND/RDL] button. (Figure 3.1.5.1-3) Memory 1 Speed Dialing (Figure 3.1.5.1-1) Memory 1 Speed Dialing (Figure 3.1.5.1-2) 1001234 Connecting…](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-23.png)
![DTP-800/DTP-1900 Operating Manual 24 ▶ The speaker phone operates automatically and the phone number stored in the Phone Book is connected. 3.1.5.2 Two-Touch Dialing This function allows you to simply make a call using the phone numbers stored in addresses 10 through 99. <Method 1> ▶ Pick up the handset or press the [SPK] button. ▶ Press the first number shortly, and then press the second number over 2 seconds of the phone number stored in any of address [10] ~ [99]. (Example) When you want to make a call to the number stored in address [12], press the [1] button shortly and press the [2] button for over 2 seconds or press the two buttons, and then press the [SND/RDL] button. (Figure 3.1.5.2-1) Memory 12 Speed Dialing (Figure 3.1.5.1-4) 1001234 Connecting…](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-24.png)
![DTP-800/DTP-1900 Operating Manual 25 ▶ The number in the Phone Book is connected. <Method 2> ▶ Press the button of the phone number stored in any of Address [10] ~ [99], and then press the [SND/RDL] button. ▶ The speaker phone operates automatically and the phone number stored in the Phone Book is connected. (Figure 3.1.5.2-2) 1001234 Connecting… (Figure 3.1.5.2-4) 1001234 Connecting… (Figure 3.1.5.2-3) Memory 12 Speed Dialing](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-25.png)
![DTP-800/DTP-1900 Operating Manual 26 3.2 Answering Calls 3.2.1 On-Hook State ▶ When a call is being received, the phone rings. ▶ If you subscribe a caller ID service, the calling party information will be displayed in the third line on the screen. And the information will be displayed in the fourth line on the screen if the calling party number is stored in your Phone Book. <Note> The calling party information is not displayed unless the service provider provides the Caller ID service. ▶ Pick up the handset or press the [SPK] button, and then the call is connected. (Figure 3.2.1-2) 1001234 00:01 (Figure 3.2.1-1) 1001234 03:DOWTEL Ringing…](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-26.png)
![DTP-800/DTP-1900 Operating Manual 27 3.2.2 Off-Hook State ▶ If a call is being received when the handset is picked up or the speaker is on, click the Hook Switch or press [SPK] button, and then the call is connected., (Figure 3.2.2-1) 1001234 Ringing… (Figure 3.2.2-2) 1001234 00:01](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-27.png)
![DTP-800/DTP-1900 Operating Manual 28 3.3 Disconnecting Calls 3.3.1 Using the Handset ▶ Hang up the handset when the call is finished. ▶ If the calling party hang up the phone before you do that, the warning-tone sound is supplied through the earpiece until you hang up the phone. 3.3.2 Using the Speaker Phone ▶ Press the [SPK] button when the call is finished. ▶ If the calling party hangs up the phone before you do that, the [SPK] lamp is turned off automatically and the speaker phone does n’t operate. (Figure 3.3.1) 11:11 am Nov 11 (Sun) (Figure 3.3.2) 11:11 am Nov 11 (Sun)](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-28.png)
![DTP-800/DTP-1900 Operating Manual 29 3.4 Transfer between Handset & Speaker Phone 3.4.1 Transfer to Speaker Phone in Off-Hook State ▶ When you press the [SPK] button under the Off-Hook state, the [SPK] lamp is turned on and voice is out through the speaker. 3.4.2 Transfer to Handset in Speaker ON State ▶ If you pick up the handset when the [SPK] lamp is on, the [SPK] lamp is turned off and voice is out through the earpiece. (Figure 3.4.1) 1001234 00:01 (Figure 3.4.2) 1001234 00:01](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-29.png)
![DTP-800/DTP-1900 Operating Manual 30 3.5 Volume Control You can adjust the volume from low to high in 5 different levels. 3.5.1 Keypad Tone Control ▶ The Keypad Tone can be changed by pressing [▲] or [▼] button when the handset is on the phone and the [SPK] button is off. 3.5.2 Ear Volume Control ▶ The Ear Volume can be changed by pressing [▲] or [▼] button after you pick up the handset. [Note] The Keypad Beep Tone is not changed even though you adjust the earpiece volume. 3.5.3 Speaker Volume Control ▶ The Speaker Volume can be changed by pressing [▲] or [▼] button after you turn the [SPK] button on. (Figure 3.5.1) ☞ Keypad Volume (Figure 3.5.2) ☞ Earpiece Volume (Figure 3.5.3-1) ☞ Speaker Volume](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-30.png)
![DTP-800/DTP-1900 Operating Manual 31 3.5.4 Ringer Volume Control ▶ The Ringer Volume can be changed by pressing [▲] or [▼] button when the phone is ringing. (Figure 3.5.4-1) ☞ Ringer Volume](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-31.png)
![DTP-800/DTP-1900 Operating Manual 32 3.6 Hot Line This function is useful when you want to make an automatic call to the designated number without dialing or pressing the [SND/RDL] button. Hot Line operates in 2 modes. ▶ Timed Hot Line : This will make a call to the designated number without dialing or pressing the [SND/RDL] button within the Sending Time(4 ~ 8 seconds) after you pick up the handset. ▶ Immediate Hot Line : This function will automatically make a call to the designated number as soon as you pick up the handset. The Hot Line number can be registered at address 99 in the Phone Book using the Phone Book function. (Reference 4.4 Using the Phone Book) You can set up the Hot Line function (ON/OFF) and the Sending Time using the Menu Mode. (Reference 5.4.3 Hotline Call) <Note> This function only operates when the Hot Line function is on and the Hot Line number must be registered at address 99 in the Phone Book. 3.6.1 Timed Hot Line ▶ Pick up the handset or press the [SPK] button. ▶ The call is connected automatically when you don’t dial or press the [SND/RDL] button during the sending time(4 ~ 8 seconds. (Default value is 6 seconds). ▶ The hot Line function is canceled if you dial or press the [SND/RDL] button within the sending time. 3.6.2 Immediate Hot Line As soon as you pick up the handset or press the [SPK] button, the hot Line is connected. (Figure 3.6.1) Hotline Dialing](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-32.png)
![DTP-800/DTP-1900 Operating Manual 33 3.7 Emergency Call Hold This function is used in the emergency situation and once the call is connected, it won’t be disconnected as long as the receiver does not hang up. You can store up to three emergency call hold numbers at address 01 ~ 03 in the Phone Book. (Reference 4.4 Phone Book Function) You can set the ON/OFF of the Emergency Call Hold function using the Menu Mode. (Reference 5.4.2 Emergency Call) <Note> This function can be operated only when the Emergency Call Hold function is on and the Emergency Call Hold number must be registered at address 01 ~ 03 in the Phone Book. ▶ Press the emergency call hold number in address 01 ~ 03 for over 2 seconds or shortly, and then press the [SND/RDL] button. ▶ The stored number is connected. [Note] - In this case, the [SPK] lamp is not turned on and you cannot hear the any voice through the speaker. The voice or sound of yours is only transmitted to the called party because only the Mic of the phone is on. - When the handset is on the phone, confirm that the speaker is off and the Mic is on. - when you pick up the handset, confirm that there is a dial tone. - In the state of the Emergency Call Hold, the line will remain be connected with the receiving party as long as the called party doesn’t hang up. If the called party hangs up the call, the call will be disconnected automatically. (Figure 3.7) No. 1 Emergency Call](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-33.png)
![DTP-800/DTP-1900 Operating Manual 34 3.8 Do Not Disturb (DND) When you don’t want to answer the incoming call, use this function. [Setting ON] ▶ Press the [DND/MUTE] button when the handset is on the phone and the [SPK] lamp is off. ▶ The phone doesn’t answer to the incoming call and the DND icon is flashing simultaneously. [Setting OFF] ▶ Press the [DND/MUTE] button when the handset is on the phone and the [SPK] lamp is off. ▶ The DND icon is disappeared and the phone is returned to the normal condition. (Figure 3.8-1) 11:11 am Nov 11 (Sun) (Figure 3.8-2) 11:11 am Nov 11 (Sun)](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-34.png)
![DTP-800/DTP-1900 Operating Manual 35 3.9 Voice Mute 3.9.1 Functions During the conversation, if you don’t want to transmit your voice or sound to the called party, use this function. You can use this function the following case. - When you input the memo in the phone Book using the keypad. - When you need to control the Menu to change the Voice Privacy function during the conversation. - When you use the Memo Storing function during the conversation. 3.9.2 Using Function ▶ Press the [DND/MUTE] button when you want to use the Voice Mute function during the conversation. ▶ Select the [Mute] menu instead of the [Unmute] menu using [▲] or [▼] button, and then press the [STORE] button. (Figure 3.9.2-1) 0192548962 00:36 (Figure 3.9.2-2) [Unmute] Voice Mute](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-35.png)
![DTP-800/DTP-1900 Operating Manual 36 ▶ When the setting is done, the Voice Mute Icon is appeared on the screen and any voice or sound will not be transmitted to the other party. ▶ If you want to release this function, select the <Unmute> in figure 3.9.2-2 and press the [STORE] button. <Note> This function is valid in each call. Even though you finish the call with [Mute] status, the phone is returned to [Unmute] status automatically. (Figure 3.9.2-3) 00:36](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-36.png)
![DTP-800/DTP-1900 Operating Manual 37 4. Additional Functions 4.1 Short Message Service (SMS) You can transmit/receive the simple text or voice message using this phone. ▶ When the phone received the text message, the sign like the figure 4.1-1 is appeared on the screen with the SMS/VMS notification tone. ▶ To retrieve the text message, ① Press the [CLR] button to return to the idle-state. ② Press the [MSG/VAS] button, and then press the [2] button. ③ Retrieve the received message. ▶ When the phone is received the voice message, the sign like the figure 4.1-2 is appeared on the screen with the beep-sound. ▶ To retrieve the voice message. ① Press the [CLR] button to return to the idle-state. ② Press the [MSG/VAS] button, and then press the [1] button. ③ The phone number of the calling party and the number of stored message is scrolled and [VMC] menu is appeared on the bottom of the screen. At this time, press the [STORE] button, and then [Send] button one by one. ④ The Message Center is connected. 4/10 11:45am MESSAGE ! (Figure 4.1-1) 4/10 11:45am VOICE MAIL (Figure 4.1-2)](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-37.png)
![DTP-800/DTP-1900 Operating Manual 38 ▶ To send the text message. ① Press the [MSG/VAS] button in the idle-state, and then press the [MENU] button. ② Press the [1] button to input the receiver’s name, and then press the [STORE] button. ③ Press the [2] button again to input the message, and then press the [STORE] button. ④ Press the [3] button to input the calling party’s name, and then press the [STORE] button. ⑤ Press the [4] button, and then the text message is transmitted to the called party.](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-38.png)
![DTP-800/DTP-1900 Operating Manual 39 4.2 Alarm Reminder This phone has Time Alarm function. You can set the alarm time under the 12-hour system. - The phone has a Two-type mode (Onetime Mode and an Always Mode). The Alarm time can be set and edit under the 12-hour system. - Onetime Mode; The alarm rings at the specified time, and then the setting mode is released automatically. But the stored time will be remained. - Always Mode; The alarm rings at the specified time every day until the setting value is released. The method of set/edit of this function will be explained the next chapter. When the alarm rings : ① Pick up the handset or press [SPK/RDL] button when the alarm rings, and then the ring will be stopped. The phone is returned in the normal state. ② If you don’t take any action during the alarm rings, the ring will be stopped after 30 seconds automatically.](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-39.png)
![DTP-800/DTP-1900 Operating Manual 40 (그림 4.3.1) Standard Voice Privacy 4.3 Voice Privacy (System Dependent) 4.3.1 On-hook State ▶ Press [MENU]à3à4 in order and Select <Enhanced> mode or <Standard> mode by using [▲] or [▼] button, and then press the [STORE] button. 4.3.2 During a Conversation ▶ Press [MENU] button during a conversation and press <1>. ▶ Select <Enhanced> mode or <Standard> mode by using [▲] or [▼] button, and then press the [STORE] button. 4.4 Authentication (System Dependant) The phone has its own authentication key function. This will prohibit any illegal use of the phone. Your service provider will register your phone using this authentication function. (그림 4.3.2) 2. Memo Dialing 1. Voice Privacy](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-40.png)
![DTP-800/DTP-1900 Operating Manual 41 4.5 Using the Phone Book 4.5.1 Store the Phone Number in idle-state ▶ When the state of the phone is in idle-state, ▶ Enter the phone number using the dial button, and then press the [STORE] button. ▶ The figure 4.5.1-3 is displayed on the screen. ▶ Type the name using the dial button, and then press the [STORE] button. ▶ If you don’t need name information, skip above, and then press the [STORE] button directly. (Figure 4.5.1-1) 11:11 am Nov 11 (Sun) (Figure 4.5.1-2) 1001234 (Figure 4.5.1-3) DOWTEL_ <<Name Reg>>](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-41.png)
![DTP-800/DTP-1900 Operating Manual 42 (Figure 4.5.2-2) 1001234 Want to store? ▶ The figure 4.5.1-4 is displayed on the screen. ▶ Press the memory location number you want to store the phone number, and then press the [STORE] button. ▶ If you just press the [STORE] button, the number is stored at memory location number [03]. 4.5.2 Storing the Caller/Receiver Number When you make a call or answer to the incoming call, the number of caller and receiver is displayed on the LCD screen. You can store this number in the Phone Book when the call is finished. [Incoming Call] ▶ The number of caller is displayed on the screen if the caller ID service is supplied by the service provider. ▶ When you finish the call, the number will be shown for 3 seconds on the screen as shown in figure 4.5.2-1. ▶ At this time, press the [STORE] button. (Reference 4.5.1) (Figure 4.5.1-4) User Define [??] Auto [03] <<Address Reg>> (Figure 4.5.2-1) 1001234 00:01](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-42.png)
![DTP-800/DTP-1900 Operating Manual 43 (Figure 4.5.2-4) 1001234 Want to store? [Note] The incoming call’s number is displayed in the left side on the screen and the making call’s number is displayed in the right side on the screen to separate between the incoming call and making call. [Making Call] ▶ The number of called party is displayed on the screen when you dial the number. ▶ When you finished a call, the number is shown for 3 seconds on the screen. ▶ At this time, press the [STORE] button. (Reference 4.5.1) (Figure 4.5.2-3) 1001234 00:01](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-43.png)
![DTP-800/DTP-1900 Operating Manual 44 4.5.3 Storing the Memo during a conversation During a conversation, you can enter the number using the dial button and store the number in the Phone Book or make a call after the call is finished. ▶ Press the [MENU] button during a conversation. ▶ Press the [2] button, and then enter the phone number during a conversation using keypad. ▶ Even though you press the dial button, the keypad tone is not transmitted and the number is just displayed on the screen. ▶ Even after the call is finished, the number is remained on the screen until you pick up the handset or press the other button. ▶ If you want to store the number to the Phone Book, press the [STORE] button. (Reference 4.5.1) ▶ if you want to call that number, just press the [SND/RDL] button. (Figure 4.5.3-1) 2. Memo Dialing 1. Voice Privacy (Figure 4.5.3-2) 0192548962 01:05 0192548962 (Figure 4.5.3-3)](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-44.png)
![DTP-800/DTP-1900 Operating Manual 45 4.5.4 Search the Stored Number ▶ When the phone is in idle-state, the screen(Figure 4.5.4-1) is displayed if you press the [RCL] button. ▶ When you press the [1] button, the screen(Figure 4.5.4-2) is displayed. ▶ Enter the memory location number using the dial button. ▶ The name and number is displayed on the screen as shown in figure 4.5.4-3. (Figure 4.5.4-3) 1001234 [Menu] for EDIT 01:DOWTEL (Figure 4.5.4-1) 2.Name Search 3.Last 10 Dialed 1.Address Search (Figure 4.5.4-2) User Define [??] <<Address Reg>>](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-45.png)
![DTP-800/DTP-1900 Operating Manual 46 ▶ If you press the [UP]/[Down] button in the figure 4.5.4-3, you can search other number. ▶ Select the address you want, and then press the [STORE] button. The phone displays the number of the stored address. ▶ When you pick up the phone or press the [SND/RDL] button, the phone make a call the selected number. ▶ If you press the [2] button in the figure 4.5.4-1, the screen(figure 4.5.4-5) is displayed on the screen. ▶ Enter the name you want to search using the dial button, and then press the [STORE] button. ▶ All stored name is displayed in the screen as shown in figure 4.5.4-6. ▶ Select the address using the [UP]/[DOWN] button, and then press the [STORE] button. The phone displays the number of the stored address. ▶ Press the [SND/RDL] button or pick up the phone, and then the phone will make a call. (Figure 4.5.4-5) DO_ <<Recall Name>> (Figure 4.5.4-4) 02:TOM 08:JERRY 01:DOWTEL (Figure 4.5.4-6) 11:FERNANDO 27:DONALD 01:DOWTEL](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-46.png)
![DTP-800/DTP-1900 Operating Manual 47 ▶ If you press the [3] button in the figure 4.5.4-1, the screen(figure 4.5.4-7) is displayed. ▶ Select the number using the [UP]/[DOWN] button, and then press the [STORE] button. The phone displays the number of the stored number. ▶ Press the [SND/RDL] button or pick up the phone, and then the phone will make a call. 4.5.5 Edit the Stored Number ▶ When you search the number using the stored address or name, the screen(figure 4.5.5-1) is displayed. ▶ Press the [Menu] button in the figure 4.5.5-1, and then the screen is changed to the figure 4.5.5-2. (Figure 4.5.4-7) 02:0166121601 03:9176203899 01:0172890085 (Figure 4.5.5-1) 1001234 [Menu] for EDIT 01:DOWTEL (Figure 4.5.5-2) 1. EDIT 2.DELETE 01:DOWTEL](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-47.png)
![DTP-800/DTP-1900 Operating Manual 48 ▶ Select the [1] button in the figure 4.5.5-1, and then you can change the number using the [CLR] and dial button. ▶ After changing the number in the figure 4.5.5-3, press the [STORE] button. ▶ The screen is changed automatically as shown in the figure 4.5.5-3, and then you can change the name using the [CLR] and dial button. ▶ If you want to store the original address or enter the other address among the address 01 ~99, press the [STORE] button, and then it’s stored. (Figure 4.5.5-3) 1001234 (Figure 4.5.5-3) DOWTEL 1001234 <<Name Reg>> (Figure 4.5.5-4) User Define Original <<Adress Reg>>](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-48.png)
![DTP-800/DTP-1900 Operating Manual 49 ▶ When the address that you enter in the figure 4.5.5-4 is already existed on the phone book, the phone will ask you to replace the address or not. ▶ If you select the “Yes”, the address will be replaced. ▶ If you select the “No”, the original number will remain at that address and you should store new address as shown on the figure 4.5.5-4. ▶ When all procedure is finished, the stored address and name will be displayed on the screen. ▶ And then the phone is returned in the idle-state automatically a few seconds later. 4.5.6 Erase the Stored Number ▶ Search the number using the address or name, the screen(figure 4.5.6-1) is displayed. (Reference 4.5.4) (Figure 4.5.5-5) 1. 2. NO < Overwrite? > (Figure 4.5.5-6) Address 01 of Phonebook Dowtel (Figure 4.5.6-1) 1001234 [Menu] for EDIT 01:DOWTEL](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-49.png)
![DTP-800/DTP-1900 Operating Manual 50 ▶ Press the [Menu] button in the figure 4.5.6-1, the screen is changed in the edit state. ▶ If you select the [2] button in the figure 4.5.6-2, the screen will be changed like the figure 4.5.6-3. ▶ If you select the “Yes”, the address will be erased. ▶ If you select the “No”, the address will not be erased and the screen will be changed to the figure 4.5.6-1. ▶ In the figure 4.5.6-3, the erasing procedure is processing if you select the “Yes” ▶ A few seconds later, the phone is returned to idle-state automatically. (Figure 4.5.6-2) 1. EDIT 2. DELETE 01:DOWTEL (Figure 4.5.6-3) [1]YES [2]NO 1001234 DELETE #01 (Figure 4.5.6-4) Deleting…](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-50.png)
![DTP-800/DTP-1900 Operating Manual 51 4.6 List of the Dialed Number 4.6.1 Last 10 Called Number ▶ Press the [RCL] button when the phone is in the idle-state. ▶ The screen (figure 4.6.1-1) is displayed. ▶ In the figure 4.6.1-1, you can see the dialed list up to 10 numbers when you press the [3] button. (Figure 4.6.1-1) 2.Name Search 3.Last 10 Calls 1.Address Search (Figure 4.6.1.-2) 02:0166121601 03:9176203899 01:0192548962](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-51.png)
![DTP-800/DTP-1900 Operating Manual 52 4.7 DATA Service 4.7.1 Definition DTP-800/1900 provides the Data Service. You can transmit and receive the data or fax data through the wireless path as connecting the Notebook (or Desktop PC) with DTP-800/1900. The following service is available. ① Async Data Service - File transmit and receive - PC communication ② PC Fax Service - Wireless Fax transmit/receive using the Winfax or Hotfax ③ Packet Data Service - FTP, Internet, Intranet, LAN, E-Mail etc. 4.7.2 Using the Data Service Reference the Appendix A. Data Service. <Note> You have to set the DTP-800/1900 with the receive mode when you receive the data using the Async Data Service and PC Fax Service. (Reference 5.5.2 PC Fax & Modem and Table DS-1) [Note] ① This phone provides both Async Data Service (14.4kbps) and Packet Data Service. ② If you want to use the Packet Data Service, you need the Internet account (free or charged) supplied by the service provider.](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-52.png)
![DTP-800/DTP-1900 Operating Manual 54 5.2 Sound Control You can select the tone types, ring types and sound volume of this phone using the Menu Mode. 5.2.1 Ring Select You can select the ring types when the phone rings. There are 6 Bell-Type and 4 Melody-Type in this phone. ▶ Press the button following sequence; [MENU] → 1 → 1 ▶ The screen(figure 5.2.1) is displayed with the current setting ring sound. ▶ At this time, select the ring type you want using the [▼] or [▲] button, and then press the [STORE] button to store the ring type. 5.2.2 DTMF Tone Length You can select the two-type mode of the DTMF Tone Length transmitted to the service provider via air when you use the additional service during the conversation or try to connect with ARS system. You can select the <Short Mode> transmit the DTMF Tone during 0.2 second when you press the dial button or the <Long Mode> which transmit the DTMF Tone while you are pressing the dial button. (Figure 5.2.1) [STORE] <Ring1> playing](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-54.png)
![DTP-800/DTP-1900 Operating Manual 55 ▶ Press the button as following sequence; [MENU] → 1 → 2 ▶ The screen(figure 5.2.2) is displayed. ▶ At this time, select the DTMF Mode you want using the [▼] or [▲] button and then press the [STORE] button to store. 5.2.3 Keypad Tone (Volume) This menu is used to select the keypad tone. This function has <Silent> mode and 5-volume level. ▶ Press the button as following sequence; [MENU] → 1 → 3 ▶ The current tone level is displayed on the screen(figure 5.2.3). ▶ At this time, select the tone level you want using the [▼] or [▲] button and then press the [STORE] button to store. [Speed Menu] You can select the tone level simply using the [▼] or [▲] button when the handset is on the phone and [SPK] lamp is off. (Figure 5.2.2) → Short DTMF Tone Length (Figure 5.2.3) ☞ Keypad Volume](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-55.png)
![DTP-800/DTP-1900 Operating Manual 56 5.2.4 Ringer Volume This menu is to select the ringer volume. This function has from <Silent> mode to 5-volume level. ▶ Press the button as following sequence; [MENU] → 1 → 4 ▶ The current volume level is displayed on the screen(figure 5.2.4). ▶ At this time, select the volume level you want using the [▼] or [▲] button and then press the [STORE] button to store the ringer volume. [Speed Menu] You can select the volume level simply using the [▼] or [▲] button when the phone is ringing. 5.2.5 Ear Volume This menu is to select the earpiece volume. This function has 5-volume level. ▶ Press the button as following sequence; [MENU] → 1 → 5 ▶ The current volume level is displayed on the screen(figure 5.2.5). ▶ At this time, select the volume level you want using the [▼] or [▲] button and then press the [STORE] button to store. (Figure 5.2.4) ☞ Ringer Volume (Figure 5.2.5) ☞ Ear Volume](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-56.png)
![DTP-800/DTP-1900 Operating Manual 57 [Speed Menu] You can select the volume level simply using the [▼] or [▲] button when you pick up the handset. 5.2.6 Speaker Volume This menu is used to select the speaker volume. This function has 5-volume level. ▶ Press the button as following sequence; [MENU] → 1 → 6 ▶ The current volume level is displayed on the screen(figure 5.2.6). ▶ At this time, select the volume level you want using the [▼] or [▲] button and then press the [STORE] button to store. [Speed Menu] You can select the volume level simply using the [▼] or [▲] button when the [SPK] lamp is on. (Figure 5.2.6) ☞ Speaker Volume](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-57.png)
![DTP-800/DTP-1900 Operating Manual 58 5.3 Management You can use this function to limit the phone use by others. And also, memory management, editing Lock Code, Reset as default and checking phone version are available. ▶ Press the button as following sequence [MENU] → 2 ▶ The phone ask you the user’s password as in the figure 5.3-1. The default password is “0000”. ▶ When you enter the user’s password, the Management Menu is displayed on the screen (Figure 5.3-1) 0000 <Enter Password> (Figure 5.3-3) 2.Clr Memory 3.ResetAsDefault 4.Phone Info (Figure 5.3-2) 2.Outgoing Lock 3.Lock Code 1.Talk Time Inf ](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-58.png)
![DTP-800/DTP-1900 Operating Manual 59 5.3.1 Talk Time Information The phone records the call time when you make a call only. You can search or erase the records using this menu. ▶ Press the button as following sequence. [MENU] → 2 → Password → 1 [Note] The item’s number 1 and 2 in this menu is initialized automatically when you turn the power of this phone off and then on again. 5.3.1.1 Recent Call ▶ The last number you dialed is displayed on the screen when you press the [1] button as the figure 5.3.1. ▶ The call time is displayed as [Hour:Minute:Second]. (Figure 5.3.1-1) (Figure 5.3.1) 2:Total Calls 3:Clr Info Above 1:Recent Call (Figure 5.3.1-1) 00:02:05 Recent Call Time](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-59.png)
![DTP-800/DTP-1900 Operating Manual 60 5.3.1.2 Total Calls ▶ The total call time is displayed on the screen when you press the [2] button as the figure 5.3.1. ▶ The total call time is displayed as [Hour:Minute:Second] & the number of Calls. 5.3.1.3 Clr(clear) Info(rmation) above The above items are initialized automatically when you turn the power off and on again. And you can initialize these items using the menu as follows. ▶ The screen (figure 5.3.1-3) is displayed when you press the [3] button as the figure 5.3.1. ▶ Press the [1] button, and then the records will be erased. (Figure 5.3.1-2) 00:05:13 3 Calls Total Calls (figure 5.3.1-3) Clear? 1.Yes 2.No Clear Info Above](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-60.png)
![DTP-800/DTP-1900 Operating Manual 61 5.3.2 Outgoing (Call) Lock This menu is to limit or permit to make a call. ▶ Press the button as following sequence. [MENU] → 2 → Password → 2 ▶ The <Yes>/<No> menu is toggled in the bottom of the screen. ▶ When the <Yes> menu is displayed, press the [STORE] button. ▶ No outgoing calls can be made. 5.3.3 Lock Code (Password Change) This menu is used to change the user’s password. ▶ Press the button as following sequence. [MENU] → 2 → Password → 3 ▶ Enter the new password, and then press the [STORE] button. ▶ The phone requires you to reenter the new password to confirm whether the new password is correct or not. ▶ Enter the new password again, and then press the [STORE] button. (Figure 5.3.2) Lock ? → Yes Outgoing Call (Figure 5.3.3-1) 0000 ENTER NEW PWD (Figure 5.3.3-2) 0000 REENTER NEW PWD](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-61.png)
![DTP-800/DTP-1900 Operating Manual 62 ▶ If the reentered new password is not correct, the figure 5.3.3-3 is displayed on the screen and the phone is returned to the figure 5.3.3-1. 5.3.4 Phone Information This menu is to confirm the number of the phone and the software version. ▶ Press the button as following sequence. [MENU] → 2 → Password → 4 ▶ The figure 5.3.4 is displayed on the screen. 5.3.4.1 Phone Number ▶ If you press the [1] button in the figure 5.3.4, the number of the phone is displayed on the screen. (Figure 5.3.3-3) Please Try Again No Match! (Figure 5.3.4) 2:S/W Version 1:Phone Number (Figure 5.3.4.1) 011-313-1234 Phone Number](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-62.png)
![DTP-800/DTP-1900 Operating Manual 63 5.3.4.2 S/W Version ▶ If you press the [2] button in the figure 5.3.4, the installed S/W Version in the phone is displayed on the screen. 5.3.5 Clear Memory This menu is to erase the list of last-dialed number and the stored numbers in the Phone Book. ▶ Press the button as following sequence. [MENU] → 2 → Password → 5 ▶ The figure 5.3.5 is displayed on the screen. 5.3.5.1 (Clear) Last 10 Calls ▶ If you press the [1] button in the figure 5.3.5, the figure 5.3.5-1 is displayed on the screen. ▶ If you want to erase the records of last 10 dialed, press the [STORE] button when “Yes” menu is appeared on the screen after press the [▲] or [▼] button. (Figure 5.3.4.2) ST0PP0-04.07 S/W Version (Figure 5.3.5) 2:Phone Book 1:Last 10 Calls (Figure 5.3.5-1) Clear ? Yes Last 10 Calls](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-63.png)
![DTP-800/DTP-1900 Operating Manual 64 5.3.5.2 (Clear) Phone Book ▶ If you press the [2] button in the figure 5.3.5, the figure 5.3.5-2 is displayed on the screen. ▶ If you want to erase the records of the Phone Book, press the [STORE] button when “Yes” menu is appeared on the screen after press the [▲] or [▼] button. 5.3.6 Reset as Default This menu is used when you want to recover the changed functions to the initial status. ▶ Press the button as following sequence. [MENU] → 2 → Password → 6 ▶ The figure 5.3.6 is displayed. ▶ If you press the [STORE] button when the “Yes” menu is appeared on the screen after you press the [▲] or [▼] button, the phone will start initializing process. ▶ At this time, the power of the phone is turned off and on automatically. ▶ If you press the [STORE] button when the “No” menu is appeared, the phone is returned to the idle-state. (Figure 5.3.5-2) Clear ? Yes Phone Book (Figure 5.3.6) Default ? Yes Reset as](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-64.png)
![DTP-800/DTP-1900 Operating Manual 66 5.4 Call Functions This menu is to set or release some useful function related with the calls. ▶ Press the button as following sequence. [MENU] → 3 ▶ The figure 5.4 is displayed on the screen. 5.4.1 Speed Dial ▶ Press the button as following sequence. [MENU] → 3 → 1 ▶ The figure 5.4.1 is displayed on the screen. ▶ If you press the [STORE] button when the <Enabled> menu is appeared after you press the [▲] or [▼] button, this function is set on. ▶ If you press the [STORE] button when the <Disable> menu is appeared, this function is released. (Figure 5.4) 2.Emergency Call 3.Hotline Call 1.Speed Dial (Figure 5.4.1) Enabled Speed Dial](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-66.png)
![DTP-800/DTP-1900 Operating Manual 67 5.4.2 Emergency Call ▶ Press the button as following sequence. [MENU] → 3 → 2 ▶ The figure 5.4.2 is displayed on the screen. ▶ If you press the [STORE] button when the <Enabled> menu is appeared after you press the [▲] or [▼] button, this function is set on. ▶ If you press the [STORE] button when the <Disable> menu is appeared, this function is released. 5.4.3 Hot-Line Call ▶ Press the button as following sequence. [MENU] → 3 → 3 ▶ The figure 5.4.3-1 is displayed on the screen. ▶ If you press the [▲] or [▼] button after press the [STORE] button, the figure 5.4.3-2 or 5.4.3-3 is displayed on the screen. (Figure 5.4.2) Enabled Emergency Call (Figure 5.4.3-1) Enabled Hotline Call (Figure 5.4.3-2) Immediate Hotline Call](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-67.png)
![DTP-800/DTP-1900 Operating Manual 68 ▶ If you press the [STORE] button when the figure 5.4.3-3 is displayed on the screen, the phone is in “Timed Hotline” state. ▶ And then the screen will be changed to the figure 5.4.3-4. ▶ When you press the [STORE] button after you set the time using the [▲] or [▼] button, the setting is done. ▶ You can set the time between 4 ~ 8 seconds. 5.4.4 Voice privacy This menu is used to set or release the privacy function to protect from the illegal wiretapping. ▶ In figure 5.4, if you press the [4] button, the figure 5.4.4-1 is displayed on the screen. ▶ At this time, the phone is in the normal privacy mode after you press the [STORE] button. (Figure 5.4.3-3) Timed Hotline Call (Figure 5.4.3-4) 6 seconds Delay Time (Figure 5.4.4-1) Standard Voice Privacy](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-68.png)
![DTP-800/DTP-1900 Operating Manual 69 ▶ If you press [▲]/[▼] button, the figure 5.4.4-2 is displayed on the screen. ▶ And then, if you press the [STORE] button, the phone is in the enhanced privacy mode. 5.4.5 Alert per 1 min This menu is used to set or release the alarm sound every 1-minute during the call. ▶ Press the button as following sequence. [MENU] → 3 → 5 ▶ The figure 5.4.5 is displayed on the screen. ▶ Select the “Yes” or “No” menu using the [▲] or [▼] button, and then press the [STORE] button. 5.4.6 Automatic Dialing This menu is used to make an automatic call even if you don’t press the [SND/RDL] button after you dialed the number within a set time.. ▶ Press the button as following sequence. [MENU] → 3 → 6 ▶ The figure 5.4.6-1 is displayed on the screen. (Figure 5.4.4-2) Enhanced Voice Privacy (Figure 5.4.5) Enabled Alert per 1 min](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-69.png)
![DTP-800/DTP-1900 Operating Manual 70 ▶ Select the “Yes” or “No” menu using the [▲] or [▼] button, and then press the [STORE] button. ▶ When you select the “Yes” menu, the figure 5.4.6-2 is displayed on the screen. ▶ Select the time using the [▲] or [▼] button, and then press the [STORE] button. 5.5 Additional Functions This menu is used to set the alarm function and the Data Receive Mode when you use the data service using the PC or Fax. ▶ Press the button as following sequence. [MENU] → 4 ▶ The figure 5.5 is displayed on the screen. (Figure 5.4.6-1) Enabled Automatic Dialing (Figure 5.4.6-2) 6 seconds Delay Time (Figure 5.5) 2:PC FAX & MODEM 1:Alarm Setting](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-70.png)
![DTP-800/DTP-1900 Operating Manual 71 5.5.1 Alarm Setting This menu is used to set on/off the alarm function and the alarm time. ▶ Press the button as following sequence. [MENU] → 4 → 1 ▶ The figure 5.5.1-1 is displayed on the screen. ▶ When you set the alarm time, the screen will prompt you to enter the time. ▶ Use the dial button when you enter the time. ▶ Use the [UP/DOWN] button when you select the AM/PM. ▶ And then, press the [STORE] button. If you enter the time incorrectly, press the [CLR] button. The entered time will be erased as inverse sequence. ▶ The figure 5.5.1-2 is displayed on the screen. ▶ If you press the [STORE] button in this stage, the entered time is stored. But the alarm function is not on. (Figure 5.5.1-1) 08:30 AM Alarm Time (Figure 5.5.1-2) Off Alarm Mode](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-71.png)
![DTP-800/DTP-1900 Operating Manual 72 ▶ If you want to use the alarm for only one time, select the figure 5.5.1-3 using the [▲] or [▼] button in the figure 5.5.1 -2 and then press the [STORE] button. ▶ If you want to use the alarm always, select the figure 5.5.1-4 using the [▲] or [▼] button in the figure 5.5.1-2 and then press the [STORE] button. 5.5.2 PC FAX & MODEM This menu is to set the phone to data receive mode when you use the Data Service to receive the fax through PC or communicate through the modem in the PC. ▶ Press the button as following sequence. [MENU] → 4 → 2 ▶ The figure 5.5.2-1 is displayed on the screen. ▶ At this time, the phone is the voice-call mode, when you press the [STORE] button. (Figure 5.5.1-3) Only Once Alarm Mode (Figure 5.5.1-4) Always Alarm Mode (Figure 5.5.2-1) Receive Mode OFF PC Fax & Modem](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-72.png)
![DTP-800/DTP-1900 Operating Manual 73 ▶ When you select the figure 5.5.2-2 using the [▲] or [▼] button in the figure 5.5.2-1, press the [STORE] button. ▶ The phone stays at the Modem Receive Mode. ▶ When you select the figure 5.5.2-3 using the [▲] or [▼] button in the figure 5.5.2-1, press the [STORE] button. ▶ The phone works the Modem Receive Mode only one time and returns to the voice-call mode. ▶ When you select the figure 5.5.2-4 using the [▲] or [▼] button in the figure 5.5.2-1, press the [STORE] button. ▶ The phone always stays at the PC Fax Receive Mode. ▶ When you select the figure 5.5.2-5 using the [▲] or [▼] button in the figure 5.5.2-1, press the [STORE] button. ▶ The phone works the PC Fax Receive Mode only one time and returns to the voice-call mode. (Figure 5.5.2-2) Receive Mode Always Modem (Figure 5.5.2-4) Receive Mode Always PC Fax (Figure 5.5.2-5) Receive Mode One Time PC Fax (Figure 5.5.2-3) Receive Mode One Time Modem](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-73.png)
![DTP-800/DTP-1900 Operating Manual 74 ▶ When the phone is set in the PC Fax Receive Mode, the PC Fax Receive Mode Icon is displayed on the screen. ▶ When the phone is set in the Modem receive Mode, the Modem receiving mode Icon is also displayed on the screen. 5.5.3 Font Select This model supplies 2 type text fonts. This menu is used to select the text font for LCD display. Default text font is <Font 1>. ▶ Press the button as following sequence. [MENU] → 4 → 3 ▶ Using the [▲] or [▼] button, Select font. And then press the [STORE] button. ▶ At this time, the phone will return to the previous menu mode, displaying with changed text font. 1:41pm Apr 09 (Mon) (Figure 5.5.3-1) Font 1 Font Select](https://usermanual.wiki/Dowtelecom/DTP-800/User-Guide-167593-Page-74.png)