Draytek 2952 Dual-WAN Security Firewall User Manual Vigor2952 Eng

Draytek Corporation Dual-WAN Security Firewall Vigor2952 Eng

User Manual

i
ii Vigor2952 Series Dual-WAN Security Firewall Quick Start Guide Version: 1.0 Firmware Version: V3.8.2_RC5 (For future update, please visit DrayTek web site) Date: December 14, 2015
i Intellectual Property Rights (IPR) Information Copyrights © All rights reserved. This publication contains information that is protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document:  Microsoft is a registered trademark of Microsoft Corp.  Windows, Windows 95, 98, Me, NT, 2000, XP, Vista, 7, 8 and Explorer are trademarks of Microsoft Corp.  Apple and Mac OS are registered trademarks of Apple Inc.  Other products may be trademarks or registered trademarks of their respective manufacturers. Safety Instructions and Approval Safety Instructions  Read the installation guide thoroughly before you set up the router.  The router is a complicated electronic unit that may be repaired only be authorized and qualified personnel. Do not try to open or repair the router yourself.  Do not place the router in a damp or humid place, e.g. a bathroom.  Do not stack the routers.  The router should be used in a sheltered area, within a temperature range of 0 to +45 Celsius.  Do not expose the router to direct sunlight or other heat sources. The housing and electronic components may be damaged by direct sunlight or heat sources.  Do not deploy the cable for LAN connection outdoor to prevent electronic shock hazards.  Keep the package out of reach of children.  When you want to dispose of the router, please follow local regulations on conservation of the environment. Warranty We warrant to the original end user (purchaser) that the router will be free from any defects in workmanship or materials for a period of two (2) years from the date of purchase from the dealer. Please keep your purchase receipt in a safe place as it serves as proof of date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, we will, at our discretion, repair or replace the defective products or components, without charge for either parts or labor, to whatever extent we deem necessary tore-store the product to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be offered solely at our discretion. This warranty will not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. The warranty does not cover the bundled or licensed software of other vendors. Defects which do not significantly affect the usability of the product will not be covered by the warranty. We reserve the right to revise the manual and online documentation and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.
ii European Community Declarations Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou Township, HsinChu Industrial Park, Hsin-Chu County, Taiwan 303 Product: Vigor2952 Series DrayTek Corp. declares that Vigor2952 Series of routers are in compliance with the following essential requirements and other relevant provisions of R&TTE 1999/5/EC, ErP 2009/125/EC and RoHS 2011/65/EU. The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by complying with the requirements set forth in EN55022/Class A and EN55024/Class A. The product conforms to the requirements of Low Voltage (LVD) Directive 2006/95/EC by complying with the requirements set forth in EN60950-1. This product is designed for 2.4GHz WLAN network throughout the EC region. Please see the user manual for the applicable networks on your product. Regulatory Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and(2) This device may accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. More update, please visit www.draytek.com.
iii Be a Registered Owner Web registration is preferred. You can register your Vigor router via http://www.draytek.com. Firmware & Tools Updates Due to the continuous evolution of DrayTek technology, all routers will be regularly upgraded. Please consult the DrayTek web site for more information on newest firmware, tools and documents. http://www.draytek.com
iv TTaabbllee ooff CCoonntteennttss 1. Introduction ........................................................................................................... 1 2. Package Content .................................................................................................. 2 3. Panel Explanation ................................................................................................. 3 4. Hardware Installation ........................................................................................... 5 5. Software Configuration ........................................................................................ 6 6. Customer Service ................................................................................................ 11
1 11.. IInnttrroodduuccttiioonn Vigor2952 is a broadband router with dual-WAN interface. It provides policy-based load-balance, fail-over and BoD (Bandwidth on Demand), also it integrates IP layer QoS, NAT session/bandwidth management to help users control works well with large bandwidth. By adopting hardware-based VPN platform, hardware encryption of AES/DES/3DS and hardware key hash of SHA-1/MD5, the router increases the performance of VPN greatly, and offers several protocols (such as IPSec/PPTP/L2TP) with up to 100 VPN tunnels. The object-originated design used in SPI (Stateful Packet Inspection) firewall allows users to set firewall policy with ease. CSM (Content Security Management) provides users control and management in IM (Instant Messenger) and P2P (Peer to Peer) more efficiency than before. By the way, DoS/DDoS prevention and URL/Web content filter strengthen the security outside and control inside. Vigor2952 series supports USB interface for connecting USB printer to share printing function, 3G/4G USB modem for network connection, or connectivity for network FTP service.
2 22.. PPaacckkaaggee CCoonntteenntt Take a look at the package content. If there is anything missed or damaged, please contact DrayTek or dealer immediately. Vigor Router Quick Start Guide RJ-45 Cat-5 Ethernet Cable Antenna (for “n” model) The type of the power adapter depends on the country that the router will be installed. * The maximum power consumption is 17-23 Watt. UK-type Power Cord EU-type Power Cord USA/Taiwan-type Power Cord AU/NZ-type Power Cord
3 33.. PPaanneell EExxppllaannaattiioonn LED Status Explanation ACT (Activity) Blinking The router is powered on and running normally. Off The router is powered off. USB1~USB2 On A USB device is connected and active. Blinking The data is transmitting. SFP On No fiber line connected. Off File line connected. WAN1~WAN2 On The WAN connection is ready. Blinking It will blink while transmitting data. QoS On The QoS function is active. WLAN On Wireless access point is ready. Blinking Ethernet packets are transmitting over wireless LAN. Off The WLAN function is inactive. CSM On The profile of CSM (Content Security Management) for IM/P2P application is enabled from Firewall >> General Setup. (Such profile is established under CSM menu). VPN On VPN tunnel is up and down. Off VPN services are disabled. Blinking Traffic is passing through VPN tunnel. LED on Connector WAN1 or Fiber WAN Left LED (Green) On The port is connected. Off The port is disconnected. Blinking The data is transmitting through WAN1 or Fiber WAN. Right LED (Green) On The WAN1/Fiber port is connected with 1000Mbps. Off The WAN1/Fiber port is connected with 10/100Mbps. WAN2 Left LED (Green) On The port is connected. Off The port is disconnected. Blinking The data is transmitting. Right LED (Green) On The port is connected with 1000Mbps. Off The port is connected with 10/100Mbps. LAN1~LAN4 Left LED (Green) On The port is connected. Off The port is disconnected.
4 Blinking The data is transmitting. Right LED (Green) On The port is connected with 1000Mbps. Off The port is connected with 10/100Mbps. Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Wireless LAN ON/OFF/WPS WLAN On - Press the button and release it within 2 seconds. When the wireless function is ready, the green LED will be on. WLAN Off - Press the button and release it within 2 seconds to turn off the WLAN function. When the wireless function is not ready, the LED will be off. WPS - When WPS function is enabled by web user interface, press this button for more than 2 seconds to wait for client’s device making network connection through WPS. Fiber Connector for accessing the Internet. WAN1~WAN2 Connector for remote networked devices. LAN1~LAN4 Connectors for local networked devices. USB1~USB2 Connector for a USB device (for 3G/4G USB Modem or printer). PWR Connector for a power cord. ON/OFF Power Switch. Note Vigor router will use either Fiber WAN or WAN1 for Internet connection. If both Fiber WAN and WAN1 are connected at the same time, Fiber WAN will be the first choice.
5 44.. HHaarrddwwaarree IInnssttaallllaattiioonn This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. Before starting to configure the router (taking Vigor2952n for example), you have to connect your devices correctly. 1. Connect a cable Modem/DSL Modem/Media Converter (depends on your requirement) to any WAN port of router with Ethernet cable (RJ-45). Or, connect the fiber cable to the WAN (SFP) port of router. 2. Connect one end of an Ethernet cable (RJ-45) to one of the LAN ports of the router and the other end of the cable (RJ-45) into the Ethernet port on your computer (that device also can connect to other computers to form a small area network). 3. Connect the power cord to the router’s power port on the rear panel, and the other side into a wall outlet. 4. Power on the device by pressing down the power switch on the rear panel. 5. The system starts to initiate. After completing the system test, the ACT LED will light up and start blinking. The WAN1/WAN2/LAN connector LED (Left or Right) will light up according to the network card feature (1000 or 100) of the device that it connected. If Fiber connection is used, check if SFP LED lights up or not. (For the detailed information of LED status, please refer to section 3. Panel Explanation)
6 55.. SSooffttwwaarree CCoonnffiigguurraattiioonn To access Internet, please finish basic configuration after completing the hardware installation. The Quick Start Wizard is designed for you to easily set up your router for Internet access. You can directly access the Quick Start Wizard via Web Configurator. 1. Make sure your PC connects to the router correctly. Note You may either simply set up your computer to get IP dynamically from the router or set up the IP address of the computer to be the same subnet as the default IP address of Vigor router 192.168.1.1. For the detailed information, please refer to the later section - Trouble Shooting of the guide. 2. Open a web browser on your PC and type http://192.168.1.1. A pop-up window will open to ask for username and password. Please type “admin/admin” as the Username/Password and click Login. Note If you fail to access to the web configuration, please go to “Trouble Shooting” for detecting and solving your problem.
7 3. Now, the Main Screen will pop up. Click Wizards>>Quick Start Wizard. Note The home page will change slightly in accordance with the router you have. 4. Enter the login password on the field of New Password and retype it on the field of Confirm Password. Then click Next to continue.
8 5. On the next page as shown below, please select the WAN interface (WAN 1 to WAN4) that you use. If Fiber interface is used, please choose WAN1. If Ethernet interface is used, please choose WAN2. If USB interface is used, choose WAN3 or WAN4. Here we take WAN2 as an example. Then, click Next for next step. Note There are four WAN selections available for you to choose. In which WAN3 /WAN4 is selected for 3G/4G USB modem connection. 6. On the next page as shown below, please select the appropriate protocol according to the information from your ISP. For example, you should select PPPoE mode if the ISP provides you PPPoE interface. Then click Next for next step.
9 PPPoE: If you click PPPoE as the protocol, after clicking Next, you will get the following web page. Please manually enter the Username/Password provided by your ISP. Then click Next. PPTP/L2TP: if you click PPTP/L2TP, you will get the following page. Please type in all the information originally provided by your ISP. Then click Next for next step.
10Static IP: if you click Static IP, you will get the following page. Please type in the IP address information originally provided by your ISP. Then click Next for next step. DHCP: if you click DHCP, you will get the following page. Simply click Next to continue.
117. Now you can see the following screen. It indicates that the setup is complete. Different types of connection modes will have different summary. Click Finish and then restart the router. Afterward, you will enjoy surfing on the Internet. 66.. CCuussttoommeerr SSeerrvviiccee If the router cannot work correctly after trying many efforts, please contact your dealer/DrayTek for further help right away. For any questions, please feel free to send e-mail to support@draytek.com.

Navigation menu