Dremel 1680 User Manual SCROLL SAW Manuals And Guides L0902530

DREMEL Saw Scroll Manual L0902530 DREMEL Saw Scroll Owner's Manual, DREMEL Saw Scroll installation guides

User Manual: Dremel 1680 1680 DREMEL SCROLL SAW - Manuals and Guides View the owners manual for your DREMEL SCROLL SAW #1680. Home:Tool Parts:Dremel Parts:Dremel SCROLL SAW Manual

Open the PDF directly: View PDF .
Page Count: 21

Download
Open PDF In Browser	View PDF

DREMEE

owner's manual

MODEL 1680, VARIABLE SPEED
16" SCROLL SAW

Parlez-vous frangais? Voir page 21
&Habla espaSol? Ver pagina 41

Voltage

rating

Amperage

rating

No load speed
Throat
Blade

assembly • operation
OREMEL

120 V _

50 - 60Hz

1.4A
n O 500-1,600/min
16"

Blade stroke

5" Plain and pin-end
3/4"

Cutting

2" at 0°; 1" at 45 °

capacity

• safety instructions
P.O. Box 1468
Racine, Wisconsin

1 -800-437-3635
http://www.dremel.com
Form No. 2610914195

7/01

Printed in Taiwan

General

Safety

"READ ALL INSTRUCTIONS"
Failure to follow
and other basic safety precautions
may result

the safety rules listed below
in serious personal injury.

DISCONNECT TOOLS FROM POWER SOURCE
When not in use, before servicing, when changing
blades, bits, cutters, etc.

Work Area
KEEP CHILDREN AWAY
Do not let visitors contact tool or extension
tors should be kept away from work area.

Rules

cord. All visi-

KEEP GUARDS IN PLACE
In working order, and in proper adjustment
alignment.

KEEP WORK AREAS CLEAN
Cluttered areas and benches invite accidents.

and

REMOVE ADJUSTING KEYS AND WRENCHES
Form the habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.

MAKE WORKSHOP CHILD-PROOF
With padlocks, master switches.

AVOID ACCIDENTAL STARTING
Make sure the switch is in the "OFF" position before plugging in tool.

AVOID DANGEROUS ENVIRONMENTS
Don't use power tools in damp or wet locations. Keep
work area well lit. Do not expose power tools to rain. Do
not use the tool in the presence of flammable liquids or
gases.

GROUND ALL TOOLS
This tool is equipped with an approved 3-conductor cord
and a 3 prong grounding type plug to fit the proper
grounding type receptacle. The green conductor in the
cord is the grounding wire. Never connect the green wire
to a live terminal.

Personal Safety
KNOW YOUR POWER TOOL
Read and understand the owner's manual and labels
affixed to the tool. Learn its application and limitations as
well as the specific potential hazards peculiar to this tool.

NEVER STAND ON TOOL OR ITS STAND
Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. Do not store materials
on or near the tool such that it is necessary to stand on the
tool or its stand to reach them.

DON'T OVERREACH
Keep proper footing and balance at all times.

CHECK DAMAGED PARTS
Before further use of the tool, a guard or other part that is
damaged should be carefully checked to ensure that it will
operate properly and perform its intended function. Check
for alignment of moving parts, mounting, and any other
conditions that may affect its operation. A guard or other
part that is damaged should be properly replaced.

STAY ALERT
Watch what you are doing. Use common sense. Do not
operate tool when you are tired. Do not operate while
under medication or while using alcohol or other drugs.
DRESS PROPERLY
Do not wear loose clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are
recommended when working outdoors. Wear protective
hair covering to contain long hair.

All repairs, electrical or mechanical, should
be attempted only by trained repairmen.
Contact the nearest Dremel Service Center, Authorized
Dremel Service Station or other competent repair service.

USE SAFETY GLASSES
Also face or dust mask if cutting operation is dusty, and ear
plugs during extended periods of operation.

Use only Dremel replacement
others may create a hazard.

Everyday eyeglasses have only impact
they are NOT safety glasses.

The use of any other accessories not specified in the current Dremel catalog, may cre-

resistant

lenses,
ate a hazard.

GUARD AGAINST ELECTRIC SHOCK
Prevent body contact with grounded surfaces. For example: pipes, radiators, ranges, refrigerator enclosures.

"SAVE THESE INSTRUCTIONS"

parts; any

Tool Use

For your own safety, do not operate your
Scroll Saw until it is completely assembled
and installed according to the instructions...and
until you
have read and understood the following:

DON'T FORCE TOOL
It will do the job better and safer at the rate for which it was
designed.

1. General Safety Rules ..............................................
2=4
2. Motor Specifications
and Electrical ..........................
Requirements
............................................................
5
3. Getting to Know Your Scroll Saw ........................ 8-9
4. Operating Adjustments
..........................................
10
5. Basic Scroll Saw Operations ............................ 11=14
6. Mounting the Scroll Saw .................................... 15-16
7. Maintaining Your Scroll Saw .................................. 17

USE THE RIGHT TOOL
Don't force a small tool or attachment to do the job of a
heavy duty tool. Don't used tool for purpose not intended-for
example, don't use a circular saw for cutting tree
limbs or logs.
SECURE WORK
Use clamps or a vise to hold work when practical. It's safer
than using your hand and it frees both hands to operate
the tool.

8. STABILITY OF SAW
Your Scroll Saw must be bolted securely to a stand or
workbench.
In addition, if there is any tendency for the
Scroll Saw to tip over or move during certain operations,
such as cutting long, heavy boards, bolt your Scroll Saw
stand or workbench to the floor.

NEVER LEAVE TOOL RUNNING UNATTENDED
Turn power off. Don't leave tool until it comes to a complete stop.

9. LOCATION
This Scroll Saw is intended for indoor use only.

Tool Care
DO NOT ALTER OR MISUSE TOOL
These tools are precision built. Any alteration or modification not specified is misuse and may result in dangerous
conditions.

10. PROTECTION:

Eyes, hands, face, ears and body.

TO AVOID BEING PULLED INTO THE
BLADE--

AVOID GASEOUS AREAS
Do not operate electric tools in a gaseous or explosive
atmosphere. Motors in these tools normally spark, and
may result in a dangerous condition.

DO NOT WEAR:

MAiNTAiN TOOLS WiTH CARE
Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing
accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect
extension cords periodically and replace if damaged. Keep
handles dry, clean and free from oil and grease.

Loose Fitting Gloves
Necktie
Loose Clothing
Jewelry

DO: TiE BACK LONG HAiR
ROLL LONG SLEEVES ABOVE ELBOWS
a. If any part of your saw is missing, malfunctioning,
has
been damaged or broken..,
such as the motor switch, or
other operating control, a safety device or the power
cord...cease operating immediately until the particular part
is properly repaired or replaced.

Before

connecting
the tool to a power
(receptacle, outlet, etc.), be sure
voltage supplied is the same as that specified on the nameplate of the tool. A power source with a voltage greater than
that specified for the tool can result in serious injury to the
user, as well as damage to the tool. If in doubt, DO NOT
PLUG IN THE TOOL. Using a power source with a voltage
less than the nameplate rating is harmful to the motor.

b. Do not cut piece too small to hold by hand.
HINT: When making a very small cut out, always secure
the workpiece to a scrap piece of plywood with doublefaced tape. This way, the work is supported and your fingers are away from the blade.
c. Never turn your Scroll Saw on before clearing the table
of all objects (tools, scraps of wood, etc.) except for the
workpiece and related feed or support devices for the
operation planned.

d. Avoid awkward hand positions where a sudden
could cause a hand to move into the blade.

slip

i. Quick Release Tension Lever should be in down position
before operating.

• ALWAYS adjust the drop foot to just clear the workpiece to protect the operator, keep blade breakage to a
minimum and provide maximum support for blade.

11. THINK SAFETY
SAFETY iS A COMBINATION OF OPERATOR COMMON
SENSE AND ALERTNESS AT ALL TIMES WHEN THE
SCROLL SAW IS BEING USED.

• Always adjust blade tension correctly.

Do not allow familiarity (gained from frequent use of your Scroll Saw) to become
commonplace. Always remember that a careless fraction
of a second is sufficient to inflict severe injury.

• The Scroll Saw should cut on the down stroke. Always
make sure blade teeth are oriented downward toward
table.
•

When cutting a large piece of material, make sure it is
supported at table height.

•

Hold the work firmly against the table.

•

Do not feed the material too fast while cutting. Only
feed the material fast enough so that the blade will cut.
Keep fingers away from the blade.

•

The operation of any power tool
can result in foreign objects

.."_,Q

Use caution when cutting off material which is irregular
in cross section, it could pinch the blade before the cut
is completed. A piece of molding, for example, must lay
flat on the table and not be permitted to rock while
being cut.

which can result in severe eye
damage.
Alwaysintowear
being thrown
the safety
eyes,
goggles that comply with ANSi
Z87.1
before
commencing
power tool operation.

Some dust created by power sanding,
sawing,
grinding,
drilling,
and other
construction
activities
contains chemicals
known to
cause cancer, birth defects or other reproductive
harm.
Some examples of these chemicals are:

Use caution when cutting off round material such as
dowel rods or tubing. They have a tendency to roll while
being cut, causing the blade to "bite".

• Lead from lead-based

paints,

• Crystalline silica from bricks
masonry products, and

e. Never leave the Scroll Saw running unattended. Turn
the saw OFF, make sure the saw has come to a complete
stop, and then remove plug from power supply before
leaving the work area.

and

cement

and other

• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic
particles.

f. Do not perform layout, assembly or setup work on the
table while the cutting tool is operating.
g. Turn saw off and remove plug from power supply outlet
before installing or removing an accessory attachment.
h. Access Door must be closed before operation.

NOTE AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS
THAT APPEAR ON THE PANEL ON SCROLL SAW HOUSING:

Motor

Specifications

Electrical

and

Requirements
prong in the attachment plug at the other end.

Motor Specifications

This plug requires a mating 3-conductor grounded type outlet
as shown. It must be grounded in accordance with all local
codes and ordinances.

In the event of a malfunction or breakdown, grounding provides
a path of least resistance for electric current to reduce the risk of
electric shock.

If the outlet you are planning to use for this power tool is of the
two-prong
type, DO NOT REMOVE OR ALTER THE
GROUNDING PRONG IN ANY MANNER. Have a qualified
electrician replace the TWO-prong outlet with a properly
grounded THREE prong outlet.

This Scroll Saw is designed to use a Variable Speed RPM motor.
It is wired for operation on 110-120 volts, 60 Hz. alternating current. Before connecting the motor cord to power source, make
certain the switch is in the "OFF" position and be sure the electric current is of the same characteristics as stamped on the
nameplate.

improper connection of the equipment-grounding
conductor
can result in a risk of electric shock. If repair or replacement of
the electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.

Connection To A Power
Source

Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if in
doubt as to whether the tool is properly grounded.

This machine must be grounded while in use to protect the operator from electric shock.
Plug power cord into a 110-120V properly grounded type outlet
protected by a 15-amp dual element time delay fuse or circuit
breaker.

The temporary adapter should be used only until a properly
grounded outlet can be installed by a qualified electrician.
The green grounding lug extending from the
adapter must be connected to a permanent
ground such as a properly grounded outlet box.

Not all outlets are properly grounded. If you are not sure that
your outlet, as pictured below, is properly grounded; have it
checked by a qualified electrician.

GROUNDING LUG

To avoid electric shock, do not touch the
metal prongs on the plug when installing or
removing the plug to or from the outlet.
Failure to properly ground this power tool can
cause electrocution or serious shock, particularly when used near metal plumbing or other metal objects.
If shocked, your reaction could cause your hands to hit the
tool.

SCREW _!

If power cord is worn, cut or damaged in any
way, have it replaced immediately to avoid
shock or fire hazard.

MAKE SURE THIS
IS CONNECTED TO
KNOWN
GROUND

ADAPTER

2-PRONG
RECEPTACLE

Your unit is for use on 120 volts; it has a plug that looks like
the one below.
NOTE: The adapter illustrated is for use only if you already
have a properly grounded 2-prong receptacle. Adapter is not
allowed in Canada by the Canadian Electrical Code. Always
use proper extension cord.

ALWAYS USE A

The use of any extension cord will cause some loss of power.
To keep this to a minimum and to prevent overheating and
motor burn-out, use the table below to determine the minimum wire size (A.W.G.) extension cord. Use only 3-wire extension cords which have 3-prong grounding type plugs and 3pole receptacles which accept the tool's plug. Make sure your
extension cord is in good condition.

GROUNDED
OUTLET

Extension Cord Length

3-PRONG PLU_NDING

PRONG

0-25
26-50
51-100

This power tool is equipped with a 3-conductor cord and
grounding type plug, approved by Underwriters Laboratories
and the Canadian Standards Association. The ground conductor has a green jacket with or without yellow stripes and is
attached to the tool housing at one end and to the ground

Feet
Feet
Feet

Wire Size A.W.G.
18
16
16

"SAVE THESE INSTRUCTIONS"
m

Table

of Contents
2

Replacing the Bulb ..........................................................

3-4

On/Off Switch ..................................................................

Variable Speed Switch ....................................................

Reset Button ....................................................................

General Safety Rules ......................................................
Additional

Safety Rules ................................................

Motor Specifications and Electrical
Requirements ..................................................................

Connection

to a Power Source ..........................................

Unpacking

and Checking

Making Interior Scroll Cuts Pin-End Blades and
Plain-End Blades ..............................................................

Table of Loose Parts ..........................................................

Mounting the Scroll Saw ..........................................

Glossary

of Terms ............................................................

Mounting the Scroll Saw to a Bench ..............................

to Know Your Scroll Saw ..............................

8-9

Mounting the Scroll Saw to Plywood ..............................

Attaching

Getting

Operating

Adjustments

Contents

..............................

................................................

Scroll Saw to Leg Set ......................................

Setting the Table for Horizontal or Bevel Cutting ............ 10

Maintaining Your Scroll

Aligning the Degree Scale Pointer ..................................

Lubrication

Basic Scroll Saw Operations

..................................

Removing and Installing Pin-End Blades ........................ 12

Trouble

Removing and Installing Plain-End Blades .................... 12

Dremel Limited

Adjusting

Service

the Lamp ..........................................................

Saw ........................................

......................................................................

Recommended

11-14

15-16

Accessories

........................................

Shooting ............................................................
Warranty

18
19

..............................................

Parts List ......................................................

61-64

Unpacking

and

Checking

Table of Loose Parts

To avoid injury from unexpected starting or
electrical shock, always remove plug from
power source when tool is not in use.

Item

Model 1680 Motorized
one carton.

A
B
C

Scroll Saw is shipped complete

Contents

1. Unpacking and Checking Contents. Separate all "loose
parts" from packing materials and check each item with
the "Table of Loose Parts" to make sure all items are
accounted for before discarding any packing material.

Description

Qty.

16" Scroll Saw ..........................................................
1
Owner's Manual ........................................................
1
Loose Parts Bag (containing) .................................... 1
Allen Wrench (3 mm) ................................................
1
Allen Wrench (5 mm) ................................................
1
Blades ....................................................................
11

NOTE: Hardware to mount this Scroll Saw to a bench or
leg set is NOT supplied. See mounting instructions on
Page 15-16 for recommended hardware size.

If any parts are missing, do not attempt to
operate Scroll Saw, plug in the power
cord or turn the switch on until the missing parts are
obtained and are installed correctly.

To remove protective coating from the table surface,
moisten a soft cloth with kerosene and wipe off coating.
Do not use acetone, gasoline or lacquer thinner for this
purpose.
After removing protective coating, If you wish, you may
apply a coat of paste wax to the table to allow the workpiece to slide easily across the table surface and deter
rust. Wipe the table thoroughly with a clean dry cloth.

Tools Needed
COMBINATION SQUARE MUST BE TRUE
Check its accuracy as illustrated below.
STRAIGHT EDGE OF
BOARD 3/4" THICKTHIS EDGE MUST BE
PERFECTLY STRAIGHT

DRAW LIGHT LINE
ON BOARD ALONG

PHILLIPS SCREWDRIVER

THIS EDGE

.3"']_

II
II

WRENCHES
7/16 in.
SHOULD BE NO GAP OR OVERLAP WHEN
SQUARE IS FLIPPED OVER IN DOTTED POSITION

COMBINATION
SQUARE

Glossary
KERF

of Terms
BLADE TOOTH SET
The distance that the edge of the sawblade
(onset) outward from the side of the blade.

The slot cut by the blade.

LEADING EDGE
The edge of the workpiece
blade first.

which is pushed into the

tooth is bent

TRAILING EDGE
The workpiece edge last cut by the sawblade.

SAWBLADE PATH
The area of the workpiece directly in line with and moving
toward the sawblade edge.

WORKPIECE
The item on which the cutting operation
formed.

9. VARIABLE

This versatile Scroll Saw is great for making toys, puzzles,
games, fretwork, and jewelry. Because of its cutting capacity, it is a handy do-it-yourself tool. It cuts wood up to 2
inches thick as well as plastics and non-ferrous metals.

is being per-

SPEED DIAL

Your Scroll Saw is equipped
greater versatility.

with a variable speed dial for

1. BLADE & WRENCH STORAGE CASE
Your Scroll Saw is equipped with a blade storage area
located on the easy access door of the saw. The blade
storage area conveniently stores your allen wrenches, and
both Pin and Plain end blades.

10. POWER ON/OFF SWITCH
Has holes provided by the switch for a lock (not included).
THIS FEATURE IS INTENDED TO PREVENT UNAUTHOURIZED
AND POSSIBLY
HAZARDOUS
USE BY
CHILDREN AND OTHERS. To turn saw on, push power
switch to the "on" position; to turn saw off, push power
switch to the "off" position.

2. SAWDUST BLOWER
Keeps workpiece clean for more accurate scroll cuts. For
best results, always direct air flow from blower tube at
blade and workpiece. To adjust, simply bend to desired
position.

11. LIGHT SWITCH
To turn light on, push light switch to the "on" position;
turn light off, push light switch to the "off" position.

12. TABLE
Provide working surface to support workpiece.

3. VACUUM HOOK-UP
Your Scroll Saw is equipped with a vacuum hook-up. This
feature will allow you to attach any 1-1/4" vacuum hose
into the hole provided for convenient sawdust removal.

12.a TABLE iNSERT
Should always be in place and flush with table during cutting operation.

4. DROP FOOT
The foot should always be lowered until it just rests on top
of the workpiece to prevent workpiece from lifting, but not
so much that the workpiece drags.

13. LIGHT

5. DROP FOOT LOCK KNOB

Allows easy access to lower blade holder when changing
blades.

Illuminates the workpiece.
14. EASY ACCESS DOOR

Allows you to raise or lower the foot and lock it at desired
heights.

15. CIRCUIT BREAKER
Protects motor from from overheating

6. QUICK RELEASE TENSION LEVER
Allows you to quickly loosen, or tighten the blade to it's
original tension with lever action.

and damage.

16. TABLE TILT DETENTS
Automatically stops the table to the right or left at 0, 15,
30, and 45 degree increments.

7. TABLE LOCK KNOB
Allows you to tilt the table and lock it at desired angle up
to 45 degrees to the right or left.

17. ALLEN WRENCHES
Convenient wrenches, assists
and adjustments if desired.

8. DEGREE SCALE
Shows the degree the table is tilted.
m

in making

blade changes

Getting

to Know

Your

Scroll

Saw

I=[_i
6
QUICK RELEASE
TENSION LEVER

9
VARIABLE SPEED
DIAL
10
POWER
ON/OFF
SWITCH

5
DROP FOOT
LOCK KNOB

11
LIGHT
SWITCH

13
LIGHT

4
DROPFOOT
12a
TABLE INSERT

12
TABLE

2
BLOWER

7
LOCK KNOB

15
CIRCUIT
BREAKER
1
BLADE & WRENCH
STORAGE CASE
14
EASY ACCESS
DOOR

8
DEGREE
SCALE

16
TABLE
TILT
DETENTS

3
VACUUM

HOJ-UP

VACUUM

DOOR

HOOK-UP

Operating

Adjustments
NOTE: When cutting at extreme angles, the drop foot
should be lifted off the workpiece, as it will impede cutting.
Hold the workpiece against the table. The drop foot may
be disassembled when thick materials are cut at extreme
angles.

Setting the Table for
Horizontal or Bevel Cutting
1. Loosen the table lock knob, and the saw table can be
tilted to the right or left and locked at any angle from 0
degree horizontal cutting position up to 45 degrees for
bevel cutting (Fig. 4). Your tool also features table tilt dentents which automaticlly stops the table to the right or left
every 15 degrees.
2. A degree scale is also provided under the work table as
a convenient reference for setting the approximate table
angle for bevel cutting. When greater precision is required,
make practice cuts and adjust the table as necessary for
your requirements.

DROP
FOOT
LOCK
KNOB

Adjusting the hold down clamp
The hold down clamp should always rest just above the
workpiece to help prevent the workpiece from lifting from
the table.

MOUNTING
SCREW

DROP
FOOT

TABLE

1. Hold the drop foot, loosen the drop foot lock knob and
lower by hand until it just rests above the workpiece surface, and securely tighten the drop foot lock knob.
2. When cutting with the table angled, adjust drop foot so
it's parallel to the table. To adjust, loosen screw with the
allen wrench provided, turn foot to correct angle, tighten
screw.
Always make sure the blade does not contact
of the drop foot, or the table opening.

TABLE
LOCK KNOB

either side

DEGREE
SCALE

Aligning the Degree Scale Pointer
The table is factory set to 0°. If further adjustments are
necessary, please follow the instructions below:
1. Loosen the table lock knob and move the table until it is
90 degree to the blade.

If adjustment is necessary. Loosen, but don't remove the
two screws holding the pointer. With the steel ball centered in the 0° detent, slide the pointer left or right until the
blade is parrallel to the square.
4. Tighten the table lock knob, both screws, and replace
drop foot, washers and screw. Remember, the degree
scale is a convenient guide but should not be relied upon
for precision. Make practice cuts in scrap wood to determine if your angle setting is correct.

2. With the wrench provided remove the drop foot assembly, mounting screw, and washer, and move it out of the
way. Place a small square on the table next to the blade as
shown in (Fig. 5) to check if the table is 90 ° to the blade. If
no adjustment is required, replace the drop foot assembly,
washer and screw.

MOUNTILG
SCREW
SQUARE

BLADE

FOOT

/
\
DEGREE
SCALE

[EL
BALL

POINTER
ADJUSTMENT SCREW

10.

Basic

Scroll

Saw

Follow these instructions for operating your Scroll Saw to
get the best results and to minimize the likelihood of personal injury.

Best results are achieved when cutting wood less than
one inch thick.
• When cutting wood thicker than one inch the user must
feed the wood very slowly into the blade, increase blade
tension and take extra care not to bend or twist the blade
while cutting in order to maximize blade life.

ALWAYS OBSERVE THE SAFETY PRECAUTIONS HERE AND ON PAGES 2, 3, 4,
AND 5.

• Teeth on Scroll Saw blades wear out and as such must be
replaced frequently for best cutting results. Scroll Saw
blades generally stay sharp for 1/2 hour to 2 hours of cutting.

1. Protection: Eyes, Hands, Face, Ears and Body
TO AVOID BEING PULLED INTO THE
BLADE--

DO NOT WEAR:

Operations

• To get accurate cuts be prepared to compensate for the
blade's tendency to follow the wood grain as you are cutting.

Loose Fitting Gloves
Necktie
Loose Clothing
Jewelry

• When choosing a blade to use with your Scroll Saw
consider the following carefully:
• Choose a blade that allows at least three (3) teeth to be in
contact with the workpiece at all times.

DO:

TIE BACK LONG HAIR
ROLL LONG SLEEVES ABOVE
ELBOWS

• Very fine, narrow blades should be used to scroll cut in thin
wood (1/4 inch thick or less).
• To cut thicker wood, use wider blades with fewer teeth per
inch.

The saw does not cut wood by itself. You allow the saw
to cut wood by guiding the wood into the blade as it
moves.
o

The blade teeth cut ONLY on the down stroke.

• Most blade packages state the size or thickness of wood
which that blade is intended to cut, and the radius (size of
curve) which can be cut with that blade.

The drop foot should always be lowered until it just rests
on top of the workpiece.

• Wider blades can't cut curves as tight or small as thinner blades.

You must feed the wood into the blade slowly because
the teeth of the blade are very small and they can only
remove wood when they are on the down stroke. The
blade will flex backwards when applying feed pressure.
Too much feed pressure will cause blade breakage.

This saw uses 5 inch long, Pin or Plain-End type blades
only (See Accessories on page 18).
Blades wear faster when (1) cutting plywood, which is
very abrasive, (2) when sawing wood which is thicker
than the 3/4 inch blade stroke, and (3) when sawing
hardwood, or when side pressure is placed on the
blade.

There is a learning curve for each person who wants to
use this saw. During that period of time it is expected that
some blades will break until you learn how to use the saw
and receive the greatest benefit from the blades.

11.

Basic

Scroll

Saw

Operations
Removing and Installing
Plain-End Blades

Blades
Your new Scroll Saw accepts 5 inch Pin-End blades or 5 inch
Plain-End blades (See Accessories on page 18).

1. Release blade tension by lifting up the Quick Release
Tension Lever (Fig. 7).

To
personal
the prevent
plug from
power injury
sourcealways
beforedisconnect
changing
blades or making adjustments.

Removing and Installing
Pin-End Blades
1. Release blade tension by lifting up the Quick Release
Tension Lever (Fig. 7).

3. Install the blade by inserting one end of the blade through
the access hole in the table and centering the blade in the
blade slot in the upper and lower blade holders. To secure
the blade securely tighten the clamping knob on the upper
and lower holders. If desired, the allen wrench provided can
assist in securely tightening the blade into the upper and
lower blade holders (Fig. 6).

2. Open easy access door and loosen the blade clamping
knob on the upper and lower blade holders. Remove blade
from the upper and lower blade holders by pulling forward on
blade and then lifting the blade through the access hole in
the table. Slight downward pressure against the upper holder may be helpful when removing blade from upper holder.

Blade Tension

3. Look at the blade holders closely and notice the blade
slots and pin recesses in the blade holders.

To tension blade, move Quick Release Tension Lever to "down"
position. As the lever is lowered, tension will be applied to the
blade (Fig. 8).

NOTE: In order to cut, and avoid uncontrollable lifting of the
workpiece, the teeth of the blade used on the Scroll Saw
should always point downward as shown in (Fig. 6) when
installed.

ATTENTION: Moving the lever downward should require moderate, steady pressure only. If heaw pressure is needed, the
blade is too tight. Loosen tension by rotating the Quick Release
Tension Lever counterclockwise 1-2 turns, then reset the tension lever to the "down" position. If the tension lever is in the
"down" position and the blade is too loose, you can increase
tension by leaving the tension lever "down" and rotating it
clockwise just until you feel the slack in the blade removed.
Then turn the tension lever ONE full turn clockwise. This amount
of blade pressure should do well for most cutting operations
and blades (Fig. 7).

4. Install the blade by inserting one end of the blade through
the access hole in the table and hook the blade pin in the pin
recess in the lower blade holder. Slide the top blade pin into
the pin recess of the upper blade holder. You may need to
press down lightly on the upper blade holder to install the
blade.
5. Check to see that the pins are properly located in the blade
holders.

When the blade tension has been properly adjusted, you should
be able to lift up the Quick Release Tension Lever, remove and
install the blade, lower the lever and return the original blade
tension.
SLIGHT
PRESSURE
HERE

I=[,_1[,I
NOTE: It may be necessary to re-adjust the tension lever when
using different types of blades.
NOB
C_AMP

___

LOOSEN

TIGHTEN
I=[._'_lr4

UPPER BLADE

QUICK RELEASE
TENSION LEVER

HOLDER
BLADE

_I(

ABLE TILTED FOR PICTURE CLARITY

QUICK RELEASE
TENSION LEVER

LOWER BLADE
HOLDER

I=[_ E=]
CLAMP
KNOB

12.

asic Scroll
Adjusting

Saw

Operations

the Lamp

LOCK KNOB

1. Position the lamp as needed to illiminate the workpiece.
2. Loosen lock knob, slide lamp to desired position
tighten lock knob (Fig. 9).

OUTER
SHADE
COVER

and

Note: Lamp shade angle is fixed and cannot be adjusted.

Replacing

the Bulb

1. Use only a (25 watt maximum), candelabra
Turn the light switch off and unplug the saw.

base bulb.
SHADESCREW

2. Remove the shade screw and the outer shade cover.

1=1[._1[_3

3. Slide the inner shade off the bulb socket.
4. Replace bulb and reassemble the shades (Fig. 9).
Note: Additional
Service.

bulbs are available

through

Customer
INNER
SHADE

ON/OFF Switch
1. To turn
(Fig. 10).

power

ON or OFF push the power

switch

B_LB

Variable Speed Switch
1.Your saw is equipped with a variable speed dial.
The blade stroke rate may be adjusted by simply rotating
the dial (Fig. 10).

VARIABLE
SPEED DIAL

I=1
[._1k"l[0]

To increase speed, rotate dial clockwise.
To reduce speed, rotate dial counterclockwise.

Reset

LIGHT

POWER
ON/OFF
SWITCH

Button

Your saw features a reset button that protects the motor
from overheating and damage (Fig. 11).

1. If the switch pops, turn the power ON/Off switch to the
off position.
2. Unplug the cord from the power source and allow the
saw to cool down.
RESET
BUTTON

3. Return reset button to its original position.

13.

SWITCH

Basic

Scroll

Saw

Making Interior Scroll Cuts
(Pin-End Blades and Plain-End Blades)
TO AVOID ACCIDENTAL
STARTING,
ALWAYS TURN SWITCH "OFF" AND
REMOVE
PLUG FROM POWER SOURCE BEFORE
REMOVING OR REPLACING THE BLADE.

A main benefit of this saw is the ability to perform intricate
interior cuts quickly and easily. This is best accomplished
using the Quick Release Tension Lever. Simply follow these
steps (Fig. 12):
1. Drill appropriate sized pilot hole in work piece.
2. Release Quick ReleaseTension Lever.
3 Remove the blade from the upper blade holder as explained
on page 12 Removing and Installing (Pin-End) or (Plain-End)
blades.
4. Thread blade through pilot hole from underneath the workpiece. If needed, remove the table insert. This will allow the
blade to fall forward for more clearance between the workpiece
and the upper arm housing. Reinstall the blade in the upper
blade holder.
5. Retension blade by pulling tension lever down.
6. Lower drop foot until it just rests on top of the workpiece and
you're ready to begin cutting.
7. When finished making the interior scroll cuts simply remove
the blade from the blade holders, as described on page 12
Removing and Installing (Pin-End) or (Plain-End) blades, and
remove the board from the table.

14.

Operations

Mounting

the

Scroll

Saw

Mounting the Scroll Saw
to a Bench
1. The Scroll Saw should be fastened securely to a firm
supporting surface such as a stand or workbench, using
the four mounting holes.

5/16"
Dia.

Note: When mounting this saw to a workbench, a solid
bench is preferable to a plywood bench where noise and
vibration will be more noticeable.

6 1/4"

We recommend to reduce noise and vibration, that a soft
foam pad be placed between your Scroll Saw and workbench. (Not Supplied)
Quantity
1

]

Description
Soft foam pad, such as carpet padding,
24"xl 2"xl/2"

2. When mounting the Scroll Saw to a workbench, holes
should be drilled through the foam pad or carpet and
mounting surface of the workbench using the dimensions
illustrated in Figure 13.
Each of the four mounting holes should be bolted securely using no less than 1/4" hex bolts, flat washers, lock
washers, and nuts. We recommend:
Quantity
4
4
4
8

I;1[0 iE!
HEX HEAD /f

Description
Hex Head Bolts,
1/4"-20 x 1/4"-20 x Length Required
Flat Washers, 9/32" I.D.
Lockwasher, 9/32" I.D.
Hex Nuts, 1/4"-20
(Hardware not supplied)

1/2" Foam PadBo_LTxL

Carpet (optional)

A. Locate and mark where the Scroll Saw is to be mounted.
B. Drill the four 5/16" holes through the workbench.
C. Place the Scroll Saw on the workbench aligning holes
in the base with the holes drilled in the workbench. Insert
all four (4) screws and tighten.

this Scroll Saw to workbench

WORKBENCH

JAM NUT /

(Fig.

15.

BASE

LOCKWASHER""a__________

ATTENTION: When inserting the front right hex head bolt,
it will be necessary to insert the hex head bolt from the
bottom side of the workbench, and secure with hex nut
from the top side of Scroll Saw Base.

SAW

Note: Do NOT overtighten mounting bolts - leave some
cushion in the foam pad for absorbing noise and vibration.

Example of mounting
14).

SCROLL

V>A

FLATWASHER
"HEX NUT

Mounting

the

Scroll

Saw

I _i[_lqi t,,l

Mounting the Scroll Saw to
Plywood

24"

5/16" Dia.

An alternative method of securing your Scroll Saw is to
fasten the Scroll Saw base to a mounting board 18" x 24".
Any good grade of plywood with a 3/4" minimum thickness is recommended.
Follow the instructions
for
"Mounting the Scroll Saw to a Bench", substituting the 18"
x 24" board for the workbench
and using 1/4"-20 Flat
Head Screws for the Hex Screws (Fig.15).

3/4,L------

Note: For proper stability, holes must be counter sunk so
screw heads are flush with the bottom surface of the supporting board.
Securely clamp
"C" Clamps.

board to workbench

6 1/4"

18"

using two or more

I=[_ H,I

Attaching the Scroll Saw to
Leg Set
(Available as Accessory)
If you prefer to mount your Scroll Saw to a leg set we recommend the leg set for benchtop tools which is available
through Dremel. The model number is 16500. This leg set
is an optional accessory and instructions to mount the
Scroll Saw to this leg set are included in the package (Fig.
16).

16.

Maintaining

Your

Maintenance

Saw

power, makes unusual noises or runs at a reduced speed,
check the brushes. To continue using the tool in this condition will permanently damage your tool.

For your own safety, turn power switch
"OFF" and remove plug from the power
source outlet before maintaining or lubricating your Scroll
Saw.
GENERAL
Frequently blow out any dust that may accumulate
the motor.

Scroll

With the cord unplugged, remove the brush caps one at a
time with a small screwdriver by rotating cap counter-clockwise and check each brush (Fig. 17).

An occasional coat of paste wax on the work table will
allow materials being cut to glide smoothly across the
work surface and deters rust.

If the brush is less than 1/8" long and the end surface of the
brush that contacts the commutator is rough and/or pitted,
they should be replaced. Check both brushes. Usually the
brushes will not wear out simultaneously. If one brush is
worn out, replace both brushes. Make sure the brushes are
installed as illustrated. The curved surface of the brush must
match the curvature of the commutator.

Certain cleaning agents and solvents damage plastic parts. Including: gasoline, cartetrachloride, chlorinated cleaning solvents, ammonia
household detergents that contain ammonia. Avoiding
of these and other types of cleaning agents minimizes
probability of damage.

After replacing brushes the tool should be run at no-load;
place it on a clean surface and run it freely for 5 minutes
before loading (or using) the tool. This will allow the brushes
to "seat" properly and will give you more hours of life from
each set of brushes. This will also extend the total life of your
tool since the commutator surface will "wear" longer.

bon
and
use
the

inside

Lubrication

To avoid shock or fire hazard, if the power
cord is worn or cut, or damaged in any way,
have it replaced immediately.

ARM BEARINGS
Lubricate the arm bearings with oil after 10 hours of use.
Re-oil after every 50 hours of use or whenever there is a
squeak coming from the bearings.

All repairs, electrical or mechanical, should
be attempted only by trained repairmen.
Contact the nearest Dremel Factory Service Center, or
other competent repair service. Use only Dremel replacement parts, any others may create a hazard.

TO LUBRICATE
1. Turn saw on its side (Fig. 18).
2. Remove rubber plug to expose bronze bearing.

Carbon Brushes

3. Squirt a generous amount of SAE 20 oil around the shaft
end and bronze bearing.

The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain
peak efficiency of the motor, we recommend every two to six
months the brushes be examined. Only genuine Dremel
replacement brushes specially designed for your tool should
be used.

4. Let the oil soak in overnight

The brushes should be inspected frequently when tools are
used continuously. If your tool runs sporadically, loses

BRUSH

in this condition.

5. Next day repeat the above procedure
side of the saw.

I=1[_ li[:]

BRUSH
CAP

I_1[_ 5kJ

@
@

17.

for the opposite

ecornrnended
Use only Dremel accessories.
ards.

Accessories

Follow instructions that accompany

accessories.

Use of improper accessories may cause haz-

LEG SET
Cat. No.
16500 Scroll Saw Stand

Saw

Blades

Dremel offers both Plain and Pin-End 5 inch blades.
PIN-END
Pin-End blades permit relatively tight radius cutting in hard and soft wood.
Cat. No.
16412
16411
16413

Suggested Usage
For cutting wood 3/8" to 2" thick
For cutting wood 3/16" to 1"thick
For cutting wood thinner than 1/4" thick

Width
Thick
.110" x .018"
.110" x .018"
.070" x .010"

TPI
x 10
x 15
x 18.5

Speed
Any
Any
Any

PLAIN-END
The Pin-End blades, while somewhat easier to put in and take out of the machine, do not always produce the same controlled
cutting action provided with the Plain-End blade. These narrow Plain-End blades allow the user to cut more detailed, intricate
patterns and smaller inside cuts.
Cat.No.
16453
16446
16443
16440
16448

Suggested Usage
For cutting hard and soft woods 1/4" to 2" thick
For close radius cutting in materials 1/8" or thicker
For very tight radius work in thin materials, up to 1/8"

Width
.062"
.038"
.029"
.022"
.045"

Thick
.020"
.016"
.012"
.010"
.017"

x
x
x
x
x

Kerr
.028" - .030"
.034" - .036"

x
x

x
x
x
x
x

TPI
9.5
12.5
20
28
11.5

Speed
High
High
High
High
High

TPI
46
41

Speed
Any

SPIRAL
Saws in all directions without turning the workpiece.
Cat. No.
16461
16463

Suggested Usage
For wood, plastic and abrasive materials

METAL PIERCING
For cutting precious and non-ferrous metals; these must be used at very slow speeds. They perform well on machines
that have variable speed capability and should be lubricated with beeswax, or a light machine oil.
Cat. No. Suggested Usage
Kerr
TPI
Speed
16483
Metals and other hardwood materials.
.033" x .016" x 36
Low
REVERSE TOOTH
Provides a smooth, splinter free finish. Eliminates the need for excessive finish sanding, and leaves a clean sharp edge on
both the top and bottom of your workpiece.
Cat. No.
16431
16432
16433

Suggested Usage
For cutting hard or soft woods up to 1/8" thick.
For cutting hard or soft woods 1/8" or thicker
For cutting hard or soft woods 3/8" to 2" thick

PERMA-GRIT

x
x
x

TPI
20
12.5
11.5

Speed
Any
Any
Any

TUNGSTEN CARBIDE

Shapes and cuts ceramic tiles cleanly and accurately.
wood. Not for use on ceramic floor tile.
Cat. No.
16471
16472

Kerr
.029" x .012"
.038" x .016"
.047" x .017"

Cuts intricate patterns easily in any direction. Also use for thin

Suggested Usage
For very tight radius work in cearmic tile or thin wood.
For close radius cutting in ceramic tile or thin wood.

18.

Kerr
.031" x .033"
.046" x .048"

Grit
60
120

Speed
Medium
Medium

Troubleshooting
Turn switch "OFF" and always remove plug from the power source before troubleshooting.

TROUBLE

PROBLEM

Breaking blades.

1. Wrong tension.

REMEDY
1. Adjust blade tension, see "REMOVING AND
INSTALLING BLADES," Page 12 (Pin End) or (Plain
End).
2. Reduce feed rate, see "BASIC SCROLL SAW

2. Over working blade.

OPERATION," Page 11.
3. Use narrow blades for cutting thin wood, wide
blades for thicker wood.

3. Wrong blade application.

4. Avoid side pressure on blade.
5. Blade should have minimum 3 teeth in contact with

4. Twisting blade in wood.
5. incorrectteeth per inch.

workpiece.
1.

Motor will not run.

1. Defective cord or plug.
2. Defective motor.

2. & 3.

3. Defective wire connections.
4. Brushes worn.

Vibration
NOTE: There will always
be some vibration present
when the saw is running
because of motor operation.

1. Improper mounting of saw.
2. Unsuitable mounting surface.

3. Loose table or table resting
against motor.

19.

Replace defective parts before using saw
again.
Consult Dremel Service. Any attempt to
repair this motor may create a HAZARD
unless repair is done by a qualified service
technician.
Replace both brushes.

1. See "MOUNTING YOUR SCROLL SAW," Pages 15
&16.
2. The heavier your work bench is, the less vibration
will occur. A plywood workbench will not be as good
a work surface as the same size solid lumber. Use
common sense in choosing a mounting surface.
3. Tighten table lock knob.

Dremel

Limited

Warranty

Your Dremel product is warranted against defective material or workmanship for a period of two years from date of purchase. In the
event of a failure of a product to conform to this written warranty, please take the following action:

1. DO NOT return your product to the place of purchase.
2. Carefully package the product by itself, with no other items, and return it, freight prepaid, along with:
A. A copy of your dated proof of purchase (please keep a copy for yourself).
B. A written statement about the nature of the problem.
C. Your name, address and phone number to:
UNITED STATES
Dremel Service Center
4915 Twenty-First Street
Racine, Wisconsin 53406

Dremel Service Center
4631 E. Sunny Dune
Palm Springs, CA 92264

CANADA
Giles Tool Agency
6520 Lawrence Av. East
Scarborough, Ont.
Canada M1C 4A7
We recommend

OUTSIDE
CONTINENTAL UNITED STATES
See your local distributor or write
to Dremel, 4915 Twenty-First St.
Racine, Wisconsin 53406

that the package be insured against loss or in transit damage for which we cannot be responsible.

This warranty applies only to the original registered purchaser. DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE, NEGLIGENCE, UNAUTHORIZED REPAIRS OR ALTERATIONS, UNAPPROVED A-FI-ACHMENTS
OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
No employee, agent, dealer or other person is authorized to give any warranties on behalf of Dremel. If Dremel inspection
shows that the problem was caused by problems with material or workmanship within the limitations of the warranty, Dremel
will repair or replace the product free of charge and return product prepaid. Repairs made necessary by normal wear or
abuse, or repair for product outside the warranty period, if they can be made, will be charged at regular factory prices.
DREMEL MAKES NO OTHER WARRANTY OF ANY KIND WHATEVER, EXPRESSED OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE ABOVE MENTIONED
OBLIGATION ARE HEREBY DISCLAIMED BY DREMEL AND EXCLUDED FROM THIS LIMITED WARRANTY.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. The obligation of
the warrantor is solely to repair or replace the product. The warrantor is not liable for any incidental or consequential damages
due to any such alleged defect. Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusion may not apply to you.
For prices and warranty fulfillment in the continental United States, contact your local Dremel distributor.

20.

ORDER BY PART NUMBER,

CODE
NO.
4
5
6
7
8
10
19
20
22
23
24
25
26
27
28
29
30
31
33
36
41
44
45
46
5O
51
52
53
54
55
56
57

PART
NO.
2610907536
2615303007
2615303043
2615303006
2610614355
2610913478
2615303038
2615302956
2615302951
2615302952
2615302953
2615302963
2615302964
2615302965
2615302962
2615302968
2615302970
2615302974
2615302999
2615296771
2615302972
2610914356
2610914357
2615302960
2615302995
2615302961
2615302950
2615303001
2615303002
2615303003
2615303004
2615303005

CODE
DESCRIPTION

NO.

Rocker Switch (2)
Cord 120V (1)
Strain Relief (2)
Cord Clamp (4)
Nameplate (1)
Dust Boot (2)
Screw (6)
Warning Label Plate (1)
Foot (4)
Cover (1)
Ball Plunger (1)
Spring (1)
Angle Indicator (1)
Ball 12 MM (1)

58
58/4
59
60
61
62
63
64
65
66
67
68
69
70

Knob (1)
Dust Cap (4)
Handle Assembly (1)
Bracket (1)
Switch Housing (1)
Brush Cap (Pair)
Counter Weight (1)
Table (1)
Table Insert (1)
Pivot Shaft (1)
Air Hose (1)
Bevel Scale (1)
Base Assembly (1)
Knob (1)
Speed Control Unit (1)
Housing (1)
Housing Cover Assembly (1) .
Control Power Cable (1)

71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
89
90

NOT CODE NUMBER

PART
NO.

DESCRIPTION

2610914358
2610914362
2615914358
2615303014
2615303015
2615303016
2610355570
2610911895
2615302973

Light Assembly (1)
Light Bulb 25 W (1)
Support Rod (1)
Blade Guard (1)
Linking Bracket (1)
Blade Holder Assembly (2) __
Washer (4)
Washer (1)
Bearing Seat Assembly (1) __

2615296167
2615303019
2615303020
2610909178
2610001734
2615303021
2610021599
2610911450
2610909171
2610306064
2615303024
2615303025
2615303026
2615303023
2615303012
2615303010

Washer (1)
Washer (1)
Washer (4)
Washer (1)
Washer (4)
Washer (1)
Washer (1)
Washer/1)
Washer (1)
Bolt (4)
Bolt (1)
Bolt (2)
Bolt (1)
Bolt (1)
Knob (1)
Knob (1)

2615303027
2615303028
2615303029
2615303030
2615303031

Set Screw (1)
Bolt w/Washer(3)
Bolt w/Washer (1)
Bolt w/Washer (3)
Screw (1)

2615302996
2615302997

PVC Hose (1)
Blower Housing (1)

WRITE FOR CURRENT PRICES--NO

PART
NO.
2615303033
91
2615302998
92
2615296164
93
2615303034
94
2615302966
95
2615303035
96
2615303036
97
2615302967
98
2615303037
99
2615302975
100
2615303039
102
2615303040
103
2610909504
104
2610910774
105
2615303042
106
2610909166
109
2610914360
111
2615302957
113
2610909173
116
2615302969
117
2615296749
118
2610909175
120
2615302971
126
2610909182
127
2610913479
131
650/13 2615303046
2610909158
650/14
2615302976
801
2615296770
810
2610914361
823
CODE
NO.

C.O.D.'S

DESCRIPTION
Screw (7)
Bellow (1)
Retainer (2)
Screw (3)
Upper Arm (1)
Screw (15)
Screw (6)
Lower Arm (1)
Screw (1)
Collar (2)
Screw (2)
Screw (2)
Screw (2)
Nut (2)
Nut (3)
Spring Clip (1)
Blade Box (1)
Hinge (1)
Lower Clamp Bolster (1)
Linkage Bar (1)
Spring (1)
Upper Clamp Bolster (1)
Spacer (1)
Spacer (1)
Switch Plate (1)
Hex Wrench 5.0 mm (1)
Hex Wrench 3.0 mm (1)
Motor Assembly (1)
Brush Spring (Pair)
Housing Set Assembly (1) __

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 21
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 4, 0, 0, 13
Create Date                     : Sun Mar 08 05:44:22 2009
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Dremel 1680 User Manual SCROLL SAW Manuals And Guides L0902530

DREMEL Saw Scroll Manual L0902530 DREMEL Saw Scroll Owner's Manual, DREMEL Saw Scroll installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation